Biostar B75MU3+ 6.x
B75MU3+ S etup Man ual
FCC Information and Copyright
This equipment has been tested and found to comply with the limits of a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. There is no guarantee
that interference will not occur in a particular installation.
The vendor makes no representations or warranties with respect to the
contents here and specially disclaims any implied warranties of merchantability
or fitness for any purpose. Further the vendor reserves the right to revise this
publication and to make changes to the contents here without obligation to
notify any party beforehand.
Duplication of this publication, in part or in whole, is not allowed without first
obtaining the vendor’s approval in writing.
The content of this user’s manual is subject to be changed without notice and
we will not be responsible for any mistakes found in this user’s manual. All the
brand and product names are trademarks of their respective companies.
Dichiarazione di conformità
sintetica
Ai sensi dell’art. 2 comma 3 del D.M.
275 del 30/10/2002
Si dichiara che questo prodotto è
conforme alle normative vigenti e
soddisfa i requisiti essenziali richiesti
dalle direttive
2004/108/CE, 2006/95/CE e
1999/05/CE
quando ad esso applicabili
Short Declaration of conformity
We declare this product is complying
with the laws in force and meeting all
the essential requirements as specified
by the directives
2004/108/CE, 2006/95/CE and
1999/05/CE
whenever these laws may be applied
Table of Contents
Chapter 1: Introduction ........................................ 1
1.1
1.2
1.3
1.4
1.5
Before You Start......................................................................................... 1
Package Checklist ..................................................................................... 1
Motherboard Features.............................................................................. 2
Rear Panel Connectors.............................................................................. 4
Motherboard Layout................................................................................. 5
Chapter 2: Hardware Installation .......................... 6
2.1
2.2
2.3
2.4
Installing Central Processing Unit (CPU) ............................................... 6
FAN Headers.............................................................................................. 8
Installing System Memory ........................................................................ 9
Connectors and Slots................................................................................ 11
Chapter 3: Headers & Jumpers Setup .................. 14
3.1
3.2
How to Setup Jumpers............................................................................. 14
Detail Settings .......................................................................................... 14
Chapter 4: Useful Help ........................................ 19
4.1
4.2
4.3
4.4
4.5
Driver Installation Note.......................................................................... 19
Software .................................................................................................... 20
Extra Information.................................................................................... 26
AMI BIOS Beep Code ............................................................................... 27
Troubleshooting ....................................................................................... 28
Appendix: SPEC In Other Languages ................... 30
German.................................................................................................................. 30
French .................................................................................................................... 32
Italian..................................................................................................................... 34
Spanish ................................................................................................................... 36
Portuguese ............................................................................................................ 38
Polish...................................................................................................................... 40
Russian ................................................................................................................... 42
Arabic..................................................................................................................... 44
Japanese ................................................................................................................ 46
B75MU3+
CHAPTER 1: INTRODUCTION
1.1
BEFORE YOU START
Thank you for choosing our product. Before you start installing the
motherboard, please make sure you follow the instructions below:
„
„
„
„
„
„
„
1.2
Prepare a dry and stable working environment with
sufficient lighting.
Always disconnect the computer from power outlet
before operation.
Before you take the motherboard out from anti-static
bag, ground yourself properly by touching any safely
grounded appliance, or use grounded wrist strap to
remove the static charge.
Avoid touching the components on motherboard or the
rear side of the board unless necessary. Hold the board
on the edge, do not try to bend or flex the board.
Do not leave any unfastened small parts inside the
case after installation. Loose parts will cause short
circuits which may damage the equipment.
Keep the computer from dangerous area, such as heat
source, humid air and water.
The operating temperatures of the computer should be
0 to 45 degrees Celsius.
PACKAGE CHECKLIST
Serial ATA Cable X 2
Rear I/O Panel for ATX Case X 1
User’s Manual X 1
Fully Setup Driver DVD X 1
Note: The package contents may be different due to area or your motherboard version.
1
Motherboard Manual
1.3
MOTHERBOARD FEATURES
SPEC
Supports Execute Disable Bit / Enhanced Intel
Socket 1155
CPU
SpeedStep® / Intel Architecture-64 / Extended
Intel Core i7 / i5 / i3 / Pentium / Celeron
Memory 64 Technology / Virtualization Technology /
processor
Hyper Threading
Chipset
Intel B75
IT8728
Environment Control initiatives,
Provides the most commonly used legacy
Hardware Monitor Controller
Super I/O functionality.
Fan Speed Controller
Low Pin Count Interface
ITE's "Smart Guardian" function
DDR3 DIMM Slots x 4
Dual Channel Mode DDR3 memory module
Main
Max Memory Capacity 32GB
Supports DDR3 1066 / 1333
Memory
Each DIMM supports 512MB/
Supports DDR3 1600 (Depending on CPU)
1GB/2GB/4GB/8GB DDR3
Registered DIMM and ECC DIMM is not supported
Super I/O
Data transfer rates up to 3.0 Gb/s / 6.0 Gb/s.
SATA 2 & 3 Integrated Serial ATA Controller
SATA Version 2.0 / 3.0 specification compliant
LAN
10 / 100 Mb/s / 1Gb/s auto negotiation
Realtek RTL 8111F
Half / Full duplex capability
Sound
Codec
USB3.0
5.1 channels audio out
ALC662
High Definition Audio
B75
Data transfer rates up to 600 MB/s
PCI Express Gen3 x 16 slot
Supports PCI-E Gen3 x16 expansion card
Slots
On Board
Connectors
2
(Depending on CPU)
x1
PCI slot
x2
Supports PCI expansion cards
PCI Express Gen2 x 1 slot
x1
Supports PCI-E Gen2 x1 expansion cards
SATA3 Connector
x1
Each connector supports 1 SATA3 devices
SATA2 Connector
x5
Each connector supports 1 SATA2 devices
Front Panel Connector
x1
Supports front panel facilities
Front Audio Connector
x1
Supports front panel audio function
B75MU3+
SPEC
CPU Fan Header
x1
CPU Fan power supply (with Smart Fan function)
System Fan Header
x1
System Fan Power supply
Clear CMOS Header
x1
Restore CMOS data to factory default
USB2.0 Connector
x2
Each connector supports 2 front panel USB2.0 ports
USB3.0 Connector
x1
Each connector supports 2 front panel USB3.0 ports
Consumer IR Connector
x1
Supports infrared function
Printer Port Connector
x1
Each connector supports 1 Printer port
Serial Port Connector
x1
Connects to RS-232 Port
S/PDIF out Connector
x1
Supports digital audio out function
Power Connector (24pin)
x1
Connects to Power supply
Power Connector (4pin)
x1
Connects to Power supply
PS/2 Keyboard
x1
Connects to PS/2 Keyboard
HDMI Port
x1
Connects to HDMI cable
VGA Port
x1
Connect to D-SUB monitor
Back Panel DVI Port
x1
Connect to DVI monitor
I/O
LAN port
x1
Connect to RJ-45 ethernet cable
USB2.0 Port
x2
Connect to USB2.0 devices
USB3.0 Port
x2
Connect to USB3.0 devices
Audio Jack
x3
Provide Audio-In/Out and Mic. connection
Board Size
220 (W) x 244 (L) mm
OS Support Windows XP / Vista / 7
ATX
Biostar reserves the right to add or remove support
for any OS with or without notice
3
Motherboard Manual
1.4
REAR PANEL CONNECTORS
PS/2
Keyboard / Mouse
LAN
Line In/
Surround
Line Out
Mic In 1/
Bass/ Center
USB2.0X2
VGA
HDMI
DVI-D
USB3.0X2
NOTE:
HDMI, DVI-D & VGA ports only work with an Intel integrated Graphics Processor.
NOTE:
USB3.0 (only supported by Windows 7) ports are backward compatible with
USB2.0/USB1.X devices.
NOTE:
Maximum resolution:
HDMI: 1920 x 1200 @60Hz, compliant with HDMI 1.4a
DVI: 1920 x 1200 @60Hz
VGA: 2048 x 1536 @75Hz
NOTE:
This motherboard supports Multiple VGA output:
z
z
z
z
z
4
Display Devices
VGA
DVI-D
VGA
X
A
HDMI
A
1
DVI-D
A
X
S , C, E
HDMI
A
S1, C, E
X
A = Single Pipe Single Display, Intel® Dual Display Clone (Only
24-bpp), or Extended Desktop Mode
C = Clone Mode
E = Extended Desktop Mode
1
S = Single Pipe Single Display With One Display Device
Disabled
X = Unsupported / Note Applicable
B75MU3+
1.5
MOTHERBOARD LAYOUT
USB_KBMS1
C PU _FA N1
VGA1
DDR3_B1
DD R3_B2
C PU1
DDR3_A2
DDR3_A1
HD MI1
Socket 1155
DVI1
ATXP W R1
R J45U SB1
BAT1
AUDIO1
JS PDI FO UT1
F_AUDIO1
PE X16_1
BIOS
P E X1_1
LAN
CODEC
B75
JC MOS 1
SATA 1
SATA 2
PCI1
CI R1
Super
I/O
PCI2
J_COM1
J_PRINT1
F_U SB 1
S YS _FA N1
JFRONT_USB3_1 F_U SB 2
S ATA 5
PAN EL1
S ATA 6
SATA 3
SATA 4
Note: ■ represents the 1st pin.
5
Motherboard Manual
CHAPTER 2: HARDWARE INSTALLATION
2.1
INSTALLING CENTRAL PROCESSING UNIT (CPU)
Notice:
1.
2.
Remove Pin Cap before installation, and make good preservation for future use.
When the CPU is removed, cover the Pin Cap on the empty socket to ensure pin
legs won’t be damaged.
The motherboard might equip with two different types of pin cap. Please refer
below instruction to remove the pin cap.
Step 1: Pull the socket locking lever out from the socket and then raise
the lever up.
Step 2: Remove the Pin Cap.
6
B75MU3+
Step 3: Look for the triangular cut edge on socket, and the golden dot on
CPU should point forwards this triangular cut edge. The CPU will
fit only in the correct orientation.
Step 4: Hold the CPU down firmly, and then lower the lever to locked
position to complete the installation.
Step 5: Put the CPU Fan and heatsink assembly on the CPU and buckle it
on the retention frame. Connect the CPU FAN power cable into
the CPU_FAN1 to complete the installation.
7
Motherboard Manual
2.2
FAN HEADERS
These fan headers support cooling-fans built in the computer. The fan
cable and connector may be different according to the fan manufacturer.
Connect the fan cable to the connector while matching the black wire to
pin#1.
CPU_FAN1: CPU Fan Header
1
4
Pin
1
2
3
4
Assignment
Ground
+12V
FAN RPM rate sense
Smart Fan Control
SYS_FAN1: System Fan Header
1
3
Pin
1
2
3
Assignment
Ground
+12V
FAN RPM rate sense
Note:
The SYS_FAN1 supports 3-pin head connector; the CPU_FAN1 supports 4-pin head
connector. When connecting with wires onto connectors, please note that the red wire is
the positive and should be connected to pin#2, and the black wire is Ground and should
be connected to GND.
8
B75MU3+
2.3
INSTALLING SYSTEM MEMORY
DDR3_B1
DDR3_B2
DDR3_A1
DDR3_A2
A. Memory Modules
1.
Unlock a DIMM slot by pressing the retaining clips outward. Align a
DIMM on the slot such that the notch on the DIMM matches the
break on the Slot.
2.
Insert the DIMM vertically and firmly into the slot until the retaining
chip snap back in place and the DIMM is properly seated.
9
Motherboard Manual
B. Memory Capacity
DIMM Socket
Location
DDR3 Module
DDR3_A1
512MB/1GB/2GB/4GB/8GB
DDR3_A2
512MB/1GB/2GB/4GB/8GB
DDR3_B1
512MB/1GB/2GB/4GB/8GB
DDR3_B2
512MB/1GB/2GB/4GB/8GB
Total Memory Size
Max is 32GB.
C. Dual Channel Memory Installation
Please refer to the following requirements to activate Dual Channel function:
Install memory module of the same density in pairs, shown in the table.
Dual Channel Status DDR3_A1 DDR3_A2 DDR3_B1 DDR3_B2
Enabled
O
X
O
X
Enabled
X
O
X
O
Enabled
O
O
O
O
(O means memory installed, X means memory not installed.)
The DRAM bus width of the memory module must be the same (x8 or
x16)
10
B75MU3+
2.4
CONNECTORS AND SLOTS
SATA1: Serial ATA3.0 Connectors
The motherboard has a PCI to SATA Controller with 1 channels SATA interface,
it satisfies the SATA 3.0 spec and with transfer rate of 6.0Gb/s.
1
4
7
Pin
1
2
3
4
5
6
7
Assignment
Ground
TX+
TXGround
RXRX+
Ground
SATA2 ~ 6: Serial ATA2.0 Connectors
The motherboard has a PCI to SATA Controller with 5 channels SATA2 interface,
it satisfies the SATA 2.0 spec and with transfer rate of 3.0Gb/s.
SATA2
SATA5 SATA3
SATA6 SATA4
1
4
7
Pin
1
2
3
4
5
6
7
Assignment
Ground
TX+
TXGround
RXRX+
Ground
11
Motherboard Manual
PEX16_1: PCI-Express Gen3 x16 Slot
-
PCI-Express 3.0 compliant.
Maximum theoretical realized bandwidth of 16GB/s simultaneously per
direction, for an aggregate of 32GB/s totally.
PCI-Express Gen3 supports a raw bit-rate of 8.0Gb/s on the data pins.
PCI-E 3.0 is supported by Core i7-3xxx / i5-3xxx CPU.
PEX1_1: PCI-Express Gen2 x1 Slot
-
PCI-Express 2.0 compliant.
Data transfer bandwidth up to 500MB/s per direction; 1GB/s in total.
PCI-Express supports a raw bit-rate of 2.5Gb/s on the data pins.
2X bandwidth over the traditional PCI architecture.
PEX 16 _1
PEX1 _1
PCI1/PCI2: Peripheral Component Interconnect Slots
This motherboard is equipped with 2 standard PCI slots. PCI stands for
Peripheral Component Interconnect, and it is a bus standard for expansion
cards. This PCI slot is designated as 32 bits.
PCI 1
PCI 2
12
B75MU3+
ATXPWR1: ATX Power Source Connector
This connector allows user to connect 24-pin power connector on the ATX
power supply.
Pin
13
14
15
16
17
18
19
20
21
22
23
24
Assignment
+3.3V
-12V
Ground
PS_ON
Ground
Ground
Ground
NC
+5V
+5V
+5V
Ground
Pin
1
2
3
4
5
6
7
8
9
10
11
12
12
24
1
13
Assignment
+3.3V
+3.3V
Ground
+5V
Ground
+5V
Ground
PW_OK
Standby Voltage+5V
+12V
+12V
+3.3V
ATXPWR2: ATX Power Source Connector
This connector provides +12V to CPU power circuit.
1
4
2
3
Pin
1
2
3
4
Assignment
+12V
+12V
Ground
Ground
Note:
Before you power on the system, please make sure that ATXPWR1 and ATXPWR2
connectors have been well plugged-in.
13
Motherboard Manual
CHAPTER 3: HEADERS & JUMPERS SETUP
3.1
HOW TO SETUP JUMPERS
The illustration shows how to set up jumpers. When the jumper cap is
placed on pins, the jumper is “close”, if not, that means the jumper is
“open”.
Pin opened
3.2
Pin closed
Pin1-2 closed
DETAIL SETTINGS
PANEL1: Front Panel Header
This 16-pin connector includes Power-on, Reset, HDD LED, Power LED, and
speaker connection. It allows user to connect the PC case’s front panel switch
functions.
POW_LED
On/Off
+ + -
9
1
16
8
+ SPK
RST
HLED
Pin
1
2
3
4
5
6
7
8
14
Assignment
+5V
N/A
N/A
Speaker
HDD LED (+)
HDD LED (-)
Ground
Reset control
Function
Speaker
Connector
Hard drive
LED
Reset button
Pin
9
10
11
12
13
14
15
16
Assignment
N/A
N/A
N/A
Power LED (+)
Power LED (+)
Power LED (-)
Power button
Ground
Function
N/A
N/A
Power LED
Power-on button
B75MU3+
F_USB1/F_USB2: Headers for USB 2.0 Ports at Front Panel
These headers allow user to connect additional USB cable on the PC front panel,
and also can be connected with internal USB devices, like USB card reader.
Pin
1
2
3
4
5
6
7
8
9
10
F_USB 1
F_USB 2
2
10
1
9
Assignment
+5V (fused)
+5V (fused)
USBUSBUSB+
USB+
Ground
Ground
Key
NC
JFRONT_USB3_1: Header for USB 3.0 Ports at Front Panel
This header allows user to connect additional USB cable on the PC front panel,
and also can be connected with internal USB devices, like USB card reader.
Pin
1
2
3
4
5
6
7
8
9
10
Assignment
VBUS0
SSRX1SSRX1+
Ground
SSTX1SSTX1+
Ground
D1D1+
ID
1
10
20
11
Pin
11
12
13
14
15
16
17
18
19
20
Assignment
D2+
D2Ground
SSTX2+
SSTX2Ground
SSRX2+
SSRX2VBUS1
Key
NOTE: USB3.0 is only supported by Windows 7.
15
Motherboard Manual
F_AUDIO1: Front Panel Audio Header
This header allows user to connect the front audio output cable with the PC front
panel. This header supports HD and AC’97 audio front panel connector.
10
9
2
1
Pin
1
2
3
4
5
6
7
8
9
10
Assignment
Mic Left in
Ground
Mic Right in
GPIO
Right line in
Jack Sense
Front Sense
Key
Left line in
Jack Sense
JSPDIFOUT1: Digital Audio-out Connector
This connector allows user to connect the PCI bracket SPDIF output header.
3
1
Pin
1
2
3
Assignment
+5V
SPDIF_OUT
Ground
CIR1: Consumer IR Connector
This header is for infrared remote control and communication.
2 6
1 5
16
Pin
1
2
3
4
5
6
Assignment
IrDA serial input
Ground
Ground
Key
IrDA serial output
IR Power
B75MU3+
JCMOS1: Clear CMOS Header
Placing the jumper on pin2-3 allows user to restore the BIOS safe setting and
the CMOS data. Please carefully follow the procedures to avoid damaging the
motherboard.
1
3
Pin 1-2 Close:
Normal Operation
(default).
1
1
3
Pin 2-3 Close:
Clear CMOS data.
3
※ Clear CMOS Procedures:
1.
2.
3.
4.
5.
6.
Remove AC power line.
Set the jumper to “Pin 2-3 close”.
Wait for five seconds.
Set the jumper to “Pin 1-2 close”.
Power on the AC.
Reset your desired password or clear the CMOS data.
J_COM1: Serial Port Connector
The motherboard has a Serial Port Connector for connecting RS-232 Port.
2
10
1
9
Pin
Assignment
1
2
3
4
5
6
7
8
9
10
Carrier detect
Received data
Transmitted data
Data terminal ready
Signal ground
Data set ready
Request to send
Clear to send
Ring indicator
NC
17
Motherboard Manual
J_PRINT1: Printer Port Connector
This header allows you to connector printer on the PC.
Pin
1
2
3
4
5
6
7
8
9
10
11
12
13
18
Assignment
-Strobe
-ALF
Data 0
-Error
Data 1
-Init
Data 2
-Scltin
Data 3
Ground
Data 4
Ground
Data 5
2
26
1
25
Pin
14
15
16
17
18
19
20
21
22
23
24
25
26
Assignment
Ground
Data 6
Ground
Data 7
Ground
-ACK
Ground
Busy
Ground
PE
Ground
SCLT
Key
B75MU3+
CHAPTER 4: USEFUL HELP
4.1
DRIVER INSTALLATION NOTE
After you installed your operating system, please insert the Fully Setup
Driver CD into your optical drive and install the driver for better system
performance.
You will see the following window after you insert the CD
The setup guide will auto detect your motherboard and operating system.
Note:
If this window didn’t show up after you insert the Driver CD, please use file browser to
locate and execute the file SETUP.EXE under your optical drive.
A. Driver Installation
To install the driver, please click on the Driver icon. The setup guide will
list the compatible driver for your motherboard and operating system.
Click on each device driver to launch the installation program.
B. Software Installation
To install the software, please click on the Software icon. The setup guide
will list the software available for your system, click on each software title
to launch the installation program.
C. Manual
Aside from the paperback manual, we also provide manual in the Driver
CD. Click on the Manual icon to browse for available manual.
Note:
You will need Acrobat Reader to open the manual file. Please download the latest version
of Acrobat Reader software from
http://www.adobe.com/products/acrobat/readstep2.html
19
Motherboard Manual
4.2
SOFTWARE
Installing Software
1. Insert the Setup CD to the optical drive. The drivers installation program
would appear if the Autorun function has been enabled.
2. Select Software Installation, and then click on the respective software
title.
3. Follow the on-screen instructions to complete the installation.
Launching Software
After the installation process, you will see the software icon “eHOT Line” /
“BIOS Update” appears on the desktop. Double-click the icon to launch the
utility.
eHot-Line (Optional)
eHot-Line is a convenient utility that helps you to contact with our
Tech-Support system. This utility will collect the system information which is
useful for analyzing the problem you may have encountered, and then send
these information to our tech-support department to help you fix the problem.
Before you use this utility, please set Outlook Express as your default e-mail client application program.
represents important
*informa
ti on that you
must provide. Wi thout
this information, you may
not be able to send out
the mail.
This bl ock will show
the i nformation which
would be collected in
the mail .
conditi on
*Describe
of your system.
your area or
*Select
the area cl ose to you.
Provide the e-ma il
address that you would
like to send the copy to.
e the name of
*Provid
the memory module
manufacturer.
Provide the name of
the power suppl y
manufacturer and the
model no.
Send the mail out.
Exi t thi s dialog.
Save these in forma tion to a .txt file
20
B75MU3+
After filling up this information, click “Send”
to send the mail out. A warning dialog would
appear asking for your confirmation; click
“Send” to confirm or “Do Not Send” to cancel.
If you want to save this information to a .txt file, click “Save As…” and then you
will see a saving dialog appears asking you to enter file name.
Enter the file name and then click
“Save”. Your system information
will be saved to a .txt file.
Open the saved .txt file, you will see
your system information including
motherboard/BIOS/CPU/video/
device/OS information. This
information is also concluded in the
sent mail.
We will not share customer’s data with any other third parties,
so please feel free to provide your system information while using
eHot-Line service.
If you are not using Outlook Express as your default e-mail client
application, you may need to save the system information to a .txt file
and send the file to our tech support with other e-mail application.
Go to the following web
http://www.biostar.com.tw/app/en-us/about/contact.php for getting
our contact information.
21
Motherboard Manual
BIOS Update
BIOS Update is a convenient utility which allows you to update your
motherboard BIOS under Windows system.
AWARD BIOS
Show current BIOS information
Clear CMOS function
(Only for AWARD BIOS)
Save current BIOS
to a .bin file
Update BIOS
with a BIOS file
<Backup BIOS>
Once click on this button, the saving
dialog will show. Choose the
position to save file and enter file
name. (We recommend that the file
name should be English/number
and no longer than 7 characters.)
Then click Save.
22
AMI BIOS
B75MU3+
<Update BIOS>
Before doing this, please download the proper BIOS file from the website.
For AWARD BIOS, update BIOS procedure
should be run with Clear CMOS function, so
please check on Clear CMOS first.
Then click Update BIOS button, a
dialog will show for asking you backup
current BIOS. Click Yes for BIOS
backup and refer to the Backup BIOS
procedure; or click No to skip this
procedure.
After the BIOS Backup procedure, the
open dialog will show for requesting the
BIOS file which is going to be updated.
Please choose the proper BIOS file for
updating, then click on Open.
The utility will update BIOS with the
proper BIOS file, and this process may
take minutes. Please do not open any
other applications during this process.
After the BIOS Update process, click on
OK to restart the system.
While the system boots up and the full screen logo shows, press
key to enter BIOS setup.
<Delete>
In the BIOS setup, use the Load Optimized Defaults function and then Save and
Exit Setup to exit BIOS setup. BIOS Update is completed.
All the information and content above about the software are subject to be changed
without notice. For better performance, the software is being continuously updated.
The information and pictures described above are for your reference only. The actual
information and settings on board may be slightly different from this manual.
23
Motherboard Manual
Intel® Small Business Advantage
Intel Small Business Advantage (Intel SBA) provides an out-of-the-box hardware-based
security and productivity suite designed for the small business user.
Supported Operating Systems:
z
z
Windows 7 Professional 64-bit and 32-bit
Windows 7 Enterprise 64-bit
Installing Intel SBA
This procedure describes how to install Intel SBA.
1.
Logon to the computer with a user that has administrator privileges.
2.
Copy the Setup.exe file to the computer.
3.
Double-click Setup.exe.
The Welcome to the Setup Program window opens.
24
B75MU3+
4.
Click Next. The installer starts the installation and the Setup Progress window
opens showing the progress of the installation. When installation is complete, the
installer starts the Intel SBA service and the Next button is enabled.
5.
Click Next. The Setup Is Complete window opens.
6.
Click Finish. The installer closes.
25
Motherboard Manual
4.3
EXTRA INFORMATION
CPU Overheated
If the system shuts down automatically after system is powered on for
seconds, the phenomenon means the CPU protection function has
been activated.
When the CPU is over heated, the motherboard will shutdown
automatically to avoid a damage of the CPU, and the system may not
power on again.
In this case, please double check:
1. The CPU cooler surface is placed evenly with the CPU surface.
2. CPU fan is rotated normally.
3. CPU fan speed is fulfilling with the CPU speed.
After confirmed, please follow steps below to relief the CPU protection
function.
1. Remove the power cord from power supply for seconds.
2. Wait for seconds.
3. Plug in the power cord and boot up the system.
Or you can:
1. Clear the CMOS data.
(See “Close CMOS Header: JCMOS1” section)
2. Wait for seconds.
3. Power on the system again.
26
B75MU3+
4.4
AMI BIOS BEEP CODE
Boot Block Beep Codes
Number of Beeps
1
2
3
4
5
7
10
11
12
13
Description
No media present. (Insert diskette in floppy drive A:)
“AMIBOOT.ROM” file not found in root directory of diskette in
A:
Insert next diskette if multiple diskettes are used for recovery
Flash Programming successful
File read error
No Flash EPROM detected
Flash Erase error
Flash Program error
“AMIBOOT.ROM” file size error
BIOS ROM image mismatch (file layout does not match
image present in flash device)
POST BIOS Beep Codes
Number of Beeps
1
3
6
7
8
Description
Memory refresh timer error
Base memory read/write test error
Keyboard controller BAT command failed
General exception error (processor exception interrupt error)
Display memory error (system video adapter)
Troubleshooting POST BIOS Beep Codes
Number of Beeps
1, 3
6, 7
8
Troubleshooting Action
Reseat the memory, or replace with known good modules.
Fatal error indicating a serious problem with the system.
Consult your system manufacturer. Before declaring the
motherboard beyond all hope, eliminate the possibility of
interference by a malfunctioning add-in card. Remove all
expansion cards except the video adapter.
z If beep codes are generated when all other expansion
cards are absent, consult your system manufacturer’s
technical support.
z If beep codes are not generated when all other expansion
cards are absent, one of the add-in cards is causing the
malfunction. Insert the cards back into the system one at a
time until the problem happens again. This will reveal the
malfunctioning card.
If the system video adapter is an add-in card, replace or
reseat the
video adapter. If the video adapter is an integrated part of the
system board, the board may be faulty.
27
Motherboard Manual
4.5
TROUBLESHOOTING
Probable
1.
There is no power in the system.
Power LED does not shine; the
fan of the power supply does not
work
2.
Indicator light on keyboard does
not shine.
System is inoperative. Keyboard lights
are on, power indicator lights are lit,
and hard drives are running.
System does not boot from a hard disk
drive, but can be booted from optical
drive.
Solution
1.
2.
3.
Make sure power cable is
securely plugged in.
Replace cable.
Contact technical support.
Using even pressure on both ends of
the DIMM, press down firmly until the
module snaps into place.
1.
Check cable running from disk to
disk controller board. Make sure
both ends are securely plugged
in; check the drive type in the
standard CMOS setup.
2.
Backing up the hard drive is
extremely important. All hard
disks are capable of breaking
down at any time.
System only boots from an optical
1.
Back up data and applications
drive. Hard disks can be read,
files.
applications can be used, but system 2.
Reformat the hard drive.
fails to boot from a hard disk.
Re-install applications and data
using backup disks.
Screen message shows “Invalid
Review system’s equipment. Make sure
Configuration” or “CMOS Failure.”
correct information is in setup.
System cannot boot after user installs a 1.
Set master/slave jumpers
second hard drive.
correctly.
2.
Run SETUP program and select
correct drive types. Call the drive
manufacturers for compatibility
with other drives.
28
B75MU3+
This page is intentionally left blank.
29
Motherboard Manual
APPENDIX: SPEC IN OTHER LANGUAGES
GERMAN
Spezifikationen
Unterstützt Execute Disable Bit / Enhanced Intel
Socket 1155
CPU
Intel Core i7 / i5 / i3 / Pentium / Celeron
Prozessoren
Chipsatz
Intel B75
Umgebungskontrolle,
Bietet die häufig verwendeten alten Super Hardware-Überwachung
E/A-Funktionen.
Lüfterdrehzahl-Controller/-Überwachung
Low Pin Count-Schnittstelle
"Smart Guardian"-Funktion von ITE
Dual-Kanal DDR3 Speichermodul
DDR3 DIMM-Steckplätze x 4
Unterstützt DDR3 1066 / 1333
Arbeitsspeich Max. 32GB Arbeitsspeicher
er
Unterstützt DDR3 1600(Depending on CPU)
Jeder DIMM unterstützt 512MB/
registrierte DIMMs. ECC DIMMs werden nicht
1GB/2GB/4GB/8GB DDR3.
SATA 2 & 3
LAN
unterstützt.
Datentransferrate bis zu 3.0Gb/s / 6.0Gb/s.
Integrierter Serial ATA-Controller
Konform mit der SATA-Spezifikation Version 2.0 / 3.0
10 / 100 / 1000 Mb/s Auto-Negotiation
Realtek RTL 8111F
Halb-/ Vollduplex-Funktion
HD
Unterstützt High-Definition Audio
Audio-Unters ALC662
5.1-Kanal-Audioausgabe
tützung
USB3.0
Steckplätze
Memory 64 Technology / Virtualization Technology /
Hyper Threading
IT8728
Super E/A
SpeedStep® / Intel Architecture-64 / Extended
B75
Datenübertragungsraten bis zu 600 MB / s
PCI Express Gen3 x16 Steckplatz
x1
PCI-Steckplatz
x2
PCI Express Gen2 x 1-Steckplatz
x1
Onboard-Ans SATA3-Anschluss
x1
Jeder Anschluss unterstützt 1 SATA3-Laufwerk
chluss
SATA2-Anschluss
x5
Jeder Anschluss unterstützt 1 SATA2-Laufwerk
Fronttafelanschluss
x1
Unterstützt die Fronttafelfunktionen
Front-Audioanschluss
x1
Unterstützt die Fronttafel-Audioanschlussfunktion
30
B75MU3+
Spezifikationen
CPU-Lüfter-Sockel
x1
System-Lüfter-Sockel
x1
"CMOS löschen"-Sockel
x1
USB2.0-Anschluss
x2
CPU-Lüfterstromversorgungsanschluss (mit Smart
Fan-Funktion)
System-Lüfter-Stromversorgungsanschluss
Jeder Anschluss unterstützt 2
Fronttafel-USB2.0-Anschlüsse
USB3.0-Anschluss
x1
Jeder Anschluss unterstützt 2
Fronttafel-USB3.0-Anschlüsse
Verbraucher-IR Anschluss
x1
Druckeranschluss Anschluss
x1
Serieller Anschluss
x1
S/PDIF Ausgangsanschluss
x1
Stromanschluss (24-polig)
x1
Stromanschluss (4-polig)
x1
PS/2-Tastatur
x1
HDMI-Anschluss
x1
VGA-Anschluss
x1
Rückseiten-E DVI-Anschluss
x1
/A
LAN-Anschluss
x1
USB2.0-Anschluss
x2
USB3.0-Anschluss
x2
Audioanschluss
x3
Platinengröße 220 mm (B) X 244 mm (L)
OS-Unterstüt
zung
Jeder Anschluss unterstützt 1 Druckeranschluss
Unterstützt die digitale Audioausgabefunktion
ATX
Biostar behält sich das Recht vor, ohne Ankündigung
Windows XP / Vista / 7
die Unterstützung für ein Betriebssystem
hinzuzufügen oder zu entfernen.
31
Motherboard Manual
FRENCH
SPEC
Prend en charge les technologies d'exécution de bit
Socket 1155
UC
Processeurs Intel Core i7 / i5 / i3 / Pentium /
Celeron
Chipset
Super E/S
Intel B75
IT8728
Initiatives de contrôle environnementales,
Fournit la fonctionnalité de Super E/S
Moniteur de matériel
patrimoniales la plus utilisée.
Contrôleur /moniteur de vitesse de ventilateur
Interface à faible compte de broches
Fonction "Gardien intelligent" de l'ITE
Module de mémoire DDR3 à mode à double voie
Mémoire
Capacité mémoire maximale de 32 Go
principale
Chaque DIMM prend en charge des DDR3 de
512Mo/1Go/2Go/4Go/8Go
10 / 100 / 1000 Mb/s négociation automatique
Realtek RTL 8111F
Half / Full duplex capability
Prise en charge de l'audio haute définition
ALC662
Sortie audio à 5.1 voies
B75
Taux de transfert de données jusqu'à 600 Mo / s
Fente PCI Express Gen3 x16
x1
Fente PCI
x2
Fente PCI Express Gen2 x1
x1
Connecteur SATA3
x1
Connecteur SATA2
x5
Connecteur du panneau avant
x1
Connecteur
embarqué
32
Les DIMM à registres et DIMM avec code correcteurs
Conforme à la spécification SATA Version 2.0 / 3.0
audio HD
Fentes
Prend en charge la DDR3 1600 (Depending on CPU)
Taux de transfert jusqu'à 3.0Go/s / 6.0Go/s.
Prise en
USB3.0
Prend en charge la DDR3 1066 / 1333
d'erreurs ne sont pas prises en charge
SATA 2 & 3 Contrôleur Serial ATA intégré :
charge
d'architecture Intel 64 / de mémoire étendue 64 / de
virtualisation / Hyper Threading
Fentes DDR3 DIMM x 4
LAN
de désactivation / Intel SpeedStep® optimisée/
Chaque connecteur prend en charge 1 périphérique
SATA3
Chaque connecteur prend en charge 1 périphérique
SATA2
Prend en charge les équipements du panneau avant
B75MU3+
SPEC
Connecteur Audio du panneau avant x1
Embase de ventilateur UC
x1
Embase de ventilateur système
x1
Embase d'effacement CMOS
x1
Connecteur USB2.0
x2
Connecteur USB3.0
x1
Prend en charge la fonction audio du panneau avant
Alimentation électrique du ventilateur UC (avec
fonction de ventilateur intelligent)
Alimentation électrique du ventilateur système
Chaque connecteur prend en charge 2 ports USB2.0
de panneau avant
Chaque connecteur prend en charge 2 ports USB3.0
de panneau avant
Connecteur de IR du consommateur x1
Connecteur de Port d'imprimante
x1
Port série
x1
Connecteur de sortie S/PDIF
x1
Connecteur d'alimentation
x1
Chaque connector prend en charge 1 Port
d'imprimante
Prend en charge la fonction de sortie audio
numérique
(24 broches)
Connecteur d'alimentation
x1
(4 broches)
E/S du
panneau
arrière
Dimensions
de la carte
Clavier PS/2
x1
Port HDMI
x1
Port VGA
x1
Port DVI
x1
Port LAN
x1
Port USB2.0
x2
Port USB3.0
x2
Fiche audio
x3
220 mm (l) X 244 mm (H)
Support SE Windows XP / Vista / 7
ATX
Biostar se réserve le droit d'ajouter ou de supprimer
le support de SE avec ou sans préavis
33
Motherboard Manual
ITALIAN
SPECIFICA
Supporto di Execute Disable Bit / Enhanced
Socket 1155
CPU
Processore Intel Core i7 / i5 / i3 /
Pentium / Celeron
Chipset
Tecnologia Extended Memory 64 / Tecnologia
Virtualization / Hyper Threading
Intel B75
IT8728
Super I/O
Intel SpeedStep® / Architettura Intel 64 /
Funzioni di controllo dell’ambiente:
Fornisce le funzionalità legacy Super I/O Monitoraggio hardware
usate più comunemente.
Controller / Monitoraggio velocità ventolina
Interfaccia LPC (Low Pin Count)
Funzione "Smart Guardian" di ITE
Modulo di memoria DDR3 a canale doppio
Alloggi DIMM DDR3 x 4
Memoria
Capacità massima della memoria 32GB
principale
Ciascun DIMM supporta DDR3
Supporto di DDR3 1066 / 1333
Supporto di DDR3 1600 (Depending on CPU)
DIMM registrati e DIMM ECC non sono
512MB/1GB/2GB/4GB/8GB
supportati
Velocità di trasferimento dei dati fino a 3.0Gb/s
SATA 2 & 3 Controller Serial ATA integrato
/ 6.0Gb/s.
Compatibile specifiche SATA Versione 2.0/3.0
LAN
Supporto
audio HD
USB3.0
Alloggi
Capacità Half / Full Duplex
Supporto audio High-Definition (HD)
ALC662
Uscita audio 5.1 canali
B75
Velocità di trasferimento dati fino a 600 MB / s
Alloggio PCI Express Gen3 x16
x1
Alloggio PCI
x2
Alloggio PCI Express Gen2 x1
x1
Connettori Connettore SATA3
su scheda
Connettore SATA2
34
Negoziazione automatica 10 / 100 / 1000 Mb/s
Realtek RTL 8111F
x1
Ciascun connettore supporta 1 unità SATA3
x5
Ciascun connettore supporta 1 unità SATA2
Connettore pannello frontale
x1
Supporta i servizi del pannello frontale
Connettore audio frontale
x1
Supporta la funzione audio pannello frontale
B75MU3+
SPECIFICA
Collettore ventolina CPU
x1
Collettore ventolina sistema
x1
Collettore cancellaz ione CMOS
x1
Connettore USB2.0
x2
Connettore USB3.0
x1
Alimentazione ventolina CPU (con funzione
Smart Fan)
Alimentazione ventolina di sistema
Ciascun connettore supporta 2 porte USB2.0
pannello frontale
Ciascun connettore supporta 2 porte USB3.0
pannello frontale
Connettore IR del consumatore x1
Ciascun connettore supporta 1 Porta
Connettore Porta stampante
x1
stampante
Porta seriale
x1
Connettore output S/PDIF
x1
Connettore alimentazione
x1
Supporta la funzione d’output audio digitale
(24 pin)
Connettore alimentazione
x1
(4 pin)
Tastiera PS/2
x1
Porta HDMI
x1
Porta VGA
x1
Porta DVI
x1
posteriore Porta LAN
x1
I/O
pannello
Dimension
i scheda
Porta USB2.0
x2
Porta USB3.0
x2
Connettore audio
x3
220 mm (larghezza) x 244 mm
(altezza)
Biostar si riserva il diritto di aggiungere o
Sistemi
operativi
supportati
ATX
Windows XP / Vista / 7
rimuovere il supporto di qualsiasi sistema
operativo senza preavviso.
35
Motherboard Manual
SPANISH
Especificación
Admite Bit de deshabilitación de ejecución / Intel
Socket 1155
CPU
Procesador Intel Core i7 / i5 / i3 / Pentium /
Celeron
Conjunto de
chips
Súper E/S
Intel B75
IT8728
Iniciativas de control de entorno,
Le ofrece las funcionalidades heredadas de
Monitor hardware
uso más común Súper E/S.
Controlador/monitor de velocidad de ventilador
Interfaz de cuenta Low Pin
Función "Guardia inteligente" de ITE
Módulo de memoria DDR3 de canal Doble
Memoria
Capacidad máxima de memoria de 32GB
principal
Cada DIMM admite DDR de
USB3.0
Ranuras
Admite DDR3 de 1600(Depending on CPU)
con ECC
Tasas de transferencia de hasta 3.0 Gb/s / 6.0 Gb/s.
SATA 2 & 3 Controlador ATA Serie Integrado
sonido HD
Admite DDR3 de 1066 / 1333
No admite DIMM registrados o DIMM compatibles
512MB/1GB/2GB/4GB/8GB
Soporte de
Tecnología Extended Memory 64 / Tecnología de
virtualización / Hyper Threading
Ranuras DIMM DDR3 x 4
Red Local
SpeedStep® Mejorado / Intel Architecture-64 /
Compatible con la versión SATA 2.0 / 3.0.
Negociación de 10 / 100 / 1000 Mb/s
Realtek RTL 8111F
Funciones Half / Full dúplex
Soporte de sonido de Alta Definición
ALC662
Salida de sonido de 5.1 canales
B75
Tasas de transferencia de datos hasta 600 MB / s
Ranura PCI Express Gen3 x16
X1
Ranura PCI
X2
Ranura PCI Express Gen2 x 1
X1
Conectores Conector SATA3
X1
Cada conector soporta 1 dispositivos SATA3
en placa
Conector SATA2
X5
Cada conector soporta 1 dispositivos SATA2
Conector de panel frontal
X1
Soporta instalaciones en el panel frontal
Conector de sonido frontal
X1
Soporta funciones de sonido en el panel frontal
36
B75MU3+
Especificación
Cabecera de ventilador de CPU
X1
Fuente de alimentación de ventilador de CPU (con
función Smart Fan)
Cabecera de ventilador de sistema X1
Fuente de alimentación de ventilador de sistema
Cabecera de borrado de CMOS
X1
Conector USB2.0
X2
Cada conector soporta 2 puertos USB2.0 frontales
Conector USB3.0
X1
Cada conector soporta 2 puertos USB3.0 frontales
Conector de IR del consumidor
X1
Conector Puerto de impresora
X1
Puerto serie
X1
Conector de salida S/PDIF
X1
Conector de alimentación
X1
Cada conector soporta 1 Puerto de impresora
Soporta función de salida de sonido digital
(24 patillas)
Conector de alimentación
X1
(4 patillas)
Panel
trasero de
E/S
Tamaño de
la placa
Teclado PS/2
X1
Puerto HDMI
x1
Puerto VGA
X1
Puerto DVI
X1
Puerto de red local
X1
Puerto USB2.0
X2
Puerto USB3.0
X2
Conector de sonido
X3
220 mm. (A) X 244 Mm. (H)
Soporte de
sistema
operativo
Windows XP / Vista / 7
ATX
Biostar se reserva el derecho de añadir o retirar el
soporte de cualquier SO con o sin aviso previo.
37
Motherboard Manual
PORTUGUESE
ESPECIFICAÇÕES
Suporta as tecnologias Execute Disable Bit /
Socket 1155
CPU
Processador Intel Core i7 / i5 / i3 / Pentium /
Celeron
Chipset
o Super I/O
/ Extended Memory 64 / Virtualization / Hyper
Threading
Intel B75
IT8728
Especificaçã
Enhanced Intel SpeedStep® / Intel Arquitecture -64
Iniciativas para controlo do ambiente
Proporciona as funcionalidades mais
utilizadas em termos da especificação Super
I/O.
Monitorização do hardware
Controlador/Monitor da velocidade da ventoinha
Função "Smart Guardian" da ITE
Interface LPC (Low Pin Count).
Módulo de memória DDR3 de canal duplo
Ranhuras DIMM DDR3 x 4
Memória
Capacidade máxima de memória: 32 GB
principal
Cada módulo DIMM suporta uma memória
DDR3 de 512MB/ 1GB/2GB/4GB/8GB
Suporta módulos DDR3 1066 / 1333
Suporta módulos DDR3 1600 (Depending on CPU)
Os módulos DIMM registados e os DIMM ECC não
são suportados
Velocidades de transmissão de dados até 3.0 Gb/s /
6.0 Gb/s.
SATA 2 & 3 Controlador Serial ATA integrado
Compatibilidade com a especificação SATA versão
2.0 / 3.0.
LAN
Auto negociação de 10 / 100 / 1000 Mb/s
Realtek RTL 8111F
Capacidade semi/full-duplex
Suporte
para áudio
de alta
Suporta a especificação High-Definition Audio
ALC662
Saída de áudio de 5.1 canais
definição
USB3.0
Ranhuras
B75
Taxas de transferência de dados até 600 MB / s
Ranhura PCI Express Gen3 x16
x1
Ranhura PCI
x2
Ranhura PCI Express Gen2 x 1
x1
Conectores Conector SATA3
x1
Cada conector suporta 1 dispositivo SATA3
Conector SATA2
x5
Cada conector suporta 1 dispositivo SATA2
Conector do painel frontal
x1
Para suporte de várias funções no painel frontal
na placa
38
B75MU3+
ESPECIFICAÇÕES
Conector de áudio frontal
x1
Conector da ventoinha da CPU
x1
Conector da ventoinha do sistema
x1
Conector para limpeza do CMOS
x1
Conector USB2.0
x2
Conector USB3.0
x1
Conector de IR do consumidor
x1
Conector da para impressora
x1
Porta série
x1
Conector de saída S/PDIF
x1
Conector de alimentação
x1
Suporta a função de áudio no painel frontal
Alimentação da ventoinha da CPU (com a função
Smart Fan)
Alimentação da ventoinha do sistema
Cada conector suporta 2 portas USB2.0 no painel
frontal
Cada conector suporta 2 portas USB3.0 no painel
frontal
Cada conector suporta 1 Porta para impressora
Suporta a saída de áudio digital
(24 pinos)
Conector de alimentação
x1
(4 pinos)
Teclado PS/2
x1
Porta HDMI
x1
Entradas/S Porta VGA
x1
aídas no
Porta DVI
x1
painel
Porta LAN
x1
traseiro
Porta USB2.0
x2
Tamanho
da placa
Porta USB3.0
x2
Tomada de áudio
x3
220 mm (L) X 244 mm (A)
Sistemas
operativos
suportados
ATX
A Biostar reserva-se o direito de adicionar ou
Windows XP / Vista / 7
remover suporte para qualquer sistema operativo
com ou sem aviso prévio.
39
Motherboard Manual
POLISH
SPEC
Obsługa Execute Disable Bit / Enhanced Intel
Socket 1155
Procesor
Procesor Intel Core i7 / i5 / i3 / Pentium /
Celeron
Chipset
SpeedStep® / Intel Architecture-64 / Extended
Memory 64 Technology / Virtualization Technology /
Hyper Threading
Intel B75
Gniazda DDR3 DIMM x 4
Moduł pamięci DDR3 z trybem podwójnego kanału
Pamięć
Maks. wielkość pamięci 32GB
Obsługa DDR3 1066 / 1333
główna
Każde gniazdo DIMM obsługuje moduły
Obsługa DDR3 1600 (Depending on CPU)
512MB/1GB/2GB/4GB/8GB DDR3
Brak obsługi Registered DIMM oraz ECC DIMM
IT8728
Funkcje kontroli warunków pracy,
Zapewnia najbardziej powszechne funkcje
Monitor H/W
Super I/O.
Kontroler/Monitor prędkości wentylatora
Interfejs Low Pin Count
Funkcja ITE "Smart Guardian"
Super I/O
Transfer danych do 3.0 Gb/s / 6.0 Gb/s.
SATA 2 & 3 Zintegrowany kontroler Serial ATA
Zgodność ze specyfikacją SATA w wersji 2.0 / 3.0.
10 / 100 / 1000 Mb/s z automatyczną negocjacją
LAN
Realtek RTL 8111F
szybkości
Działanie w trybie połowicznego / pełnego dupleksu
Obsługa
audio HD
USB3.0
Obsługa High-Definition Audio
ALC662
5.1 kanałowe wyjście audio
B75
Cena transferu danych do 600 MB / s
Gniazdo PCI Express Gen3 x16
x1
Gniazdo PCI
x2
Gniazdo PCI Express Gen2 x 1
x1
Złącze SATA3
x1
Każde złącze obsługuje 1 urządzenie SATA3
wbudowane Złącze SATA2
x5
Każde złącze obsługuje 1 urządzenie SATA2
Złącze panela przedniego
x1
Obsługa elementów panela przedniego
Przednie złącze audio
x1
Obsługa funkcji audio na panelu przednim
Gniazda
Złącza
Złącze główkowe wentylatora
procesora
40
Zasilanie wentylatora procesora (z funkcją Smart
x1
Fan)
B75MU3+
SPEC
Złącze główkowe wentylatora
systemowego
x1
Zasilanie wentylatora systemowego
Złącze główkowe kasowania CMOS x1
Złącze USB2.0
x2
Złącze USB3.0
x1
Złącze Konsument IR
x1
Złącze Port drukarki
x1
Port szeregowy
x1
Złącze wyjścia S/PDIF
x1
Złącze zasilania (24 pinowe)
x1
Złącze zasilania (4 pinowe)
x1
Klawiatura PS/2
x1
Port HDMI
x1
Port VGA
x1
Back Panel Port DVI
x1
I/O
Port LAN
x1
Port USB2.0
x2
Port USB3.0
x2
Gniazdo audio
x3
Wymiary
płyty
220 mm (S) X 244 mm (W)
Obsluga
systemu
operacyjne
go
Każde złącze obsługuje 2 porty USB2.0 na panelu
przednim
Każde złącze obsługuje 2 porty USB3.0 na panelu
przednim
Każde złącze obsługuje 1 Port drukarki
Obsługa funkcji cyfrowego wyjścia audio
ATX
Biostar zastrzega sobie prawo dodawania lub
Windows XP / Vista / 7
odwoływania obsługi dowolnego systemu
operacyjnego bez powiadomienia.
41
Motherboard Manual
RUSSIAN
СПЕЦ
CPU
(центральн
ый
Поддержка технологий Execute Disable Bit /
Socket 1155
Процессор Intel Core i7 / i5 / i3 / Pentium /
Celeron
/ Extended Memory 64 Technology / технологии
виртуализация / Hyper Threading
процессор)
Набор
Enhanced Intel SpeedStep® / Intel Architecture-64
Intel B75
микросхем
Модуль памяти с двухканальным режимом DDR3
Слоты DDR3 DIMM x 4
Основная
Максимальная ёмкость памяти 32 ГБ
память
Каждый модуль DIMM поддерживает
512МБ/1ГБ/2ГБ/4ГБ/8 ГБ DDR3
Super I/O
Поддержка DDR3 1066 / 1333
Поддержка DDR3 1600(Depending on CPU)
Не поддерживает зарегистрированные модули
DIMM and ECC DIMM
IT8728
Инициативы по охране окружающей среды,
Обеспечивает наиболее используемые
Аппаратный монитор
действующие функциональные
Регулятор скорости вентилятора/ монитор
возможности Super I/O.
Функция ITE "Smart Guardian"
Интерфейс с низким количеством выводов (Интеллектуальная защита)
SATA 2 & 3
Локальная
Встроенное последовательное устройство
управления ATA
скорость передачи данных до 3.0 гигабит/с /
6.0 гигабит/с.
Соответствие спецификации SATA версия 2.0/3.0
Автоматическое согласование 10 / 100 / 1000
Realtek RTL 8111F
Мб/с
сеть
Частичная / полная дуплексная способность
Звуковая
поддержка
Звуковая поддержка High-Definition
ALC662
5.1канальный звуковой выход
жесткого
диска
USB3.0
Слоты
B75
Слот PCI Express Gen3 x16
x1
Слот PCI
x2
Слот PCI Express Gen2 x 1
Встроенны Разъём SATA3
Разъём SATA2
й разъём
Разъём на лицевой панели
Входной звуковой разъём
42
скорости передачи данных до 600 МБ / с
x1
x1
Каждый разъём поддерживает 1 устройство SATA3
x5
Каждый разъём поддерживает 1 устройство SATA2
x1
x1
Поддержка устройств на лицевой панели
Поддержка звуковых функций на лицевой
панели
B75MU3+
СПЕЦ
Источник питания для вентилятора центрального
Контактирующее приспособление
вентилятора центрального процессора x1
Контактирующее приспособление
вентилятора системы
x1
процессора (с функцией интеллектуального
вентилятора)
Источник питания для вентилятора системы
Открытое контактирующее
приспособление CMOS
x1
USB2.0-разъём
x2
USB3.0-разъём
x1
Разъём едока ИКЫЙ
x1
Разъём Порт подключения
Задняя
принтера
x1
Последовательный порт
x1
Разъём вывода для S/PDIF
x1
Разъем питания (24 вывод)
x1
Разъем питания (4 вывод)
x1
Клавиатура PS/2
x1
Порт HDMI
x1
Порт VGA
x1
Порт DVI
x1
средств
Порт LAN
x1
USB2.0-порт
x2
USB3.0-порт
x2
ода
лицевой панели
подключения принтера
Поддержка вывода цифровой звуковой функции
Гнездо для подключения
наушников
Размер
лицевой панели
Каждый разъём поддерживает 2 USB3.0-порта на
Каждый разъём поддерживает 1 Порт
панель
ввода-выв
Каждый разъём поддерживает 2 USB2.0-порта на
220 мм (Ш) X 244 мм (В)
x3
ATX
панели
Поддержка
OS
Biostar сохраняет за собой право добавлять или
Windows XP / Vista / 7
удалять средства обеспечения для OS с или без
предварительного уведомления.
43
‫‪Motherboard Manual‬‬
‫‪ARABIC‬‬
‫اﻟﻤﻮاﺻﻔﺎت‬
‫‪Execute Disable Bit / Enhanced Intel‬ﺗﺪﻋﻢ ﺗﻘﻨﻴﺎت‬
‫‪Socket 1155‬‬
‫وﺣﺪة اﻟﻤﻌﺎﻟﺠﺔ‬
‫اﻟﻤﺮآﺰیﺔ‬
‫‪Intel Core i7 / i5 / i3 / Pentium /‬ﻣﻌﺎﻟﺠﺎت‬
‫ﺑﺘﺮدد یﺼﻞ إﻟﻰ ‪Celeron‬‬
‫‪SpeedStep® / Intel Architecture-64 / Extended‬‬
‫‪Memory 64 Technology / Virtualization Technology /‬‬
‫‪Hyper Threading‬‬
‫ﻣﺠﻤﻮﻋﺔ اﻟﺸﺮاﺋﺢ ‪Intel B75‬‬
‫ﻣﺰدوﺝﺔ اﻟﻘﻨﺎة‪DDR3‬وﺣﺪة ذاآﺮة‬
‫ﺳﻌﺎت ‪ 1333 / 1066‬ﻣﻴﺠﺎ ﺑﺎیﺖ‪DDR3‬ﺗﺪﻋﻢ اﻟﺬاآﺮة ﻣﻦ ﻥﻮع‬
‫اﻟﺬاآﺮة اﻟﺮﺋﻴﺴﻴﺔ ‪ 1600(Depending‬ﺳ ﻌﺎت ‪ DDR3‬ﻧ ﻮع ﻣﻦ اﻟﺬاآﺮة ﺗ ﺪﻋﻢ‬
‫ﺑﺎی ﺖ ﻣﻴﺠ ﺎ )‪on CPU‬‬
‫ﻓﺘﺤﺔ ‪DDR3 DIMM‬‬
‫ﻋﺪد‪4‬‬
‫ﺳﻌﺔ ذاآﺮة ﻗﺼﻮى ‪ 32‬ﺝﻴﺠﺎ ﺑﺎیﺖ‬
‫ﻣﻴﺠﺎ ﺑﺎیﺖ و‪ /512 /1‬ﺳﻌﺔ ‪ DDR3‬ﺗﺪﻋﻢ ذاآﺮة ﻣﻦ ﻥﻮع ‪DIMM‬ﺗﺪﻋﻢ آﻞ ﻓﺘﺤﺔ‬
‫و‪ /2‬و‪ /4‬و‪ 8‬ﺝﻴﺠﺎ ﺑﺎیﺖ‬
‫‪ ECC‬وﺗﻠﻚ اﻟﺘﻲ ﻻ ﺗﺘﻮاﻓﻖ ﻣﻊ ‪DIMM‬ﻻ ﺗﺪﻋﻢ رﻗﺎﺋﻖ اﻟﺬاآﺮة‬
‫وﺳﺎﺋﻞ اﻟﺘﺤﻜﻢ ﻓﻲ اﻟﺒﻴﺌﺔ‪:‬‬
‫‪IT8728‬‬
‫ﻣﺮاﻗﺐ ﻟﻤﻌﺮﻓﺔ ﺣﺎﻟﺔ اﻷﺝﻬﺰة‬
‫‪ Super I/O‬اﻷآﺜﺮ اﺳﺘﺨﺪاﻣًﺎ‪Super I/O .‬ﺗﻮﻓﺮ وﻇﻴﻔﺔ‬
‫ﻣﺮاﻗﺐ ﻓﻲ ﺳﺮﻋﺔ اﻟﻤﺮوﺣﺔ‬
‫‪Low Pin Count Interface‬ﺗﺪﻋﻢ ﺗﻘﻨﻴﺔ‬
‫‪ ITE‬ﻣﻦ "‪"Smart Guardian‬وﻇﻴﻔﺔ‬
‫‪ / 6.0‬ﺛﺎﻧﻴ ﺔ‪/‬ﺝﻴﺠﺎﺑ ﺖ ‪ 3.0‬إﻟ ﻰ ﺗﺼ ﻞ ﺑﺴ ﺮﻋﺎت تاﻟﺒﻴﺎﻧ‬
‫‪ SATA 2 & 3‬ﻣﺘﻜﺎﻣﻞ‪Serial ATA‬ﻣﺘﺤﻜﻢ‬
‫ﺎ ﻧﻘ ﻞ‬
‫‪.‬ﺛﺎﻧﻴ ﺔ‪/‬ﺝﻴﺠﺎﺑ ﺖ‬
‫‪ 2.0 / 3.0.‬اﻹﺹﺪار ‪SATA‬ﻣﻄﺎﺑﻘﺔ ﻟﻤﻮاﺹﻔﺎت‬
‫ﺗﻔﺎوض ﺗﻠﻘﺎﺋﻲ ‪ 100/10‬ﻣﻴﺠﺎ ﺑﺎیﺖ ‪ /‬ﺙﺎﻥﻴﺔ و‪1‬ﺝﻴﺠﺎ ﺑﺖ‪/‬ﺙﺎﻥﻴﺔ‬
‫ﺵﺒﻜﺔ داﺥﻠﻴﺔ ‪Realtek RTL 8111F‬‬
‫دﻋﻢ اﻟﺼﻮت ﻋﺎﻟﻲ‬
‫اﻟﺘﻌﺮیﻒ‬
‫إﻣﻜﺎﻥﻴﺔ اﻟﻨﻘﻞ اﻟﻤﺰدوج اﻟﻜﺎﻣﻞ‪/‬اﻟﻨﺼﻔﻲ‬
‫ﺗﺪﻋﻢ ﺗﻘﻨﻴﺔ اﻟﺼﻮت ﻋﺎﻟﻲ اﻟﺘﻌﺮیﻒ ﻣﻦ‬
‫‪ALC662‬‬
‫‪ 5.1‬ﻗﻨﻮات ﻟﺨﺮج اﻟﺼﻮت‬
‫‪B75 USB3.0‬‬
‫ﻓﺘﺤﺔ‪PCI Express x16 Gen3‬‬
‫اﻟﻔﺘﺤﺎت ﻓﺘﺤﺔ ‪PCI‬‬
‫ﻓﺘﺤﺔ ‪PCI Express Gen2 x 1‬‬
‫ﺛﺎﻧﻴ ﺔ ‪ /‬ﺑﺎی ﺖ ﻣﻴﻐ ﺎ ‪ 600‬إﻟ ﻰ ﺗﺼ ﻞ ﺑﻴﺎﻧ ﺎت ﻧﻘ ﻞ ﻣﻌﺪﻻت‬
‫ﻋﺪد‪1‬‬
‫ﻋﺪد ‪2‬‬
‫ﻋﺪد ‪1‬‬
‫اﻟﻤﻨﺎﻓﺬ ﻋﻠﻰ ﺳﻄﺢ ﻣﻨﻔﺬ ‪SATA3‬‬
‫ﻋﺪد ‪1‬‬
‫یﺪﻋﻢ آﻞ ﻣﻨﻔﺬ واﺣﺪ ﻣﻦ أﺝﻬﺰة ‪SATA3‬‬
‫اﻟﻠﻮﺣﺔ ﻣﻨﻔﺬ ‪SATA2‬‬
‫ﻋﺪد ‪5‬‬
‫یﺪﻋﻢ آﻞ ﻣﻨﻔﺬ واﺣﺪ ﻣﻦ أﺝﻬﺰة ‪SATA2‬‬
‫ﻣﻨﻔﺬ اﻟﻠﻮﺣﺔ اﻷﻣﺎﻣﻴﺔ‬
‫ﻋﺪد ‪1‬‬
‫یﺪﻋﻢ ﺗﺠﻬﻴﺰات اﻟﻠﻮﺣﺔ اﻷﻣﺎﻣﻴﺔ‬
‫ﻣﻨﻔﺬ اﻟﺼﻮت اﻷﻣﺎﻣﻲ‬
‫ﻋﺪد ‪1‬‬
‫یﺪﻋﻢ وﻇﻴﻔﺔ اﻟﺼﻮت ﺑﺎﻟﻠﻮﺣﺔ اﻷﻣﺎﻣﻴﺔ‬
‫وﺹﻠﺔ ﻣﺮوﺣﺔ وﺣﺪة اﻟﻤﻌﺎﻟﺠﺔ اﻟﻤﺮآﺰیﺔ‬
‫ﻋﺪد ‪1‬‬
‫ﻟﺘﻮﺹﻴﻞ اﻟﻄﺎﻗﺔ ﻟﻤﺮوﺣﺔ وﺣﺪة اﻟﻤﻌﺎﻟﺠﺔ ﻣﻊ وﻇﻴﻔﺔ ‪Smart Fan‬‬
‫‪44‬‬
‫‪B75MU3+‬‬
‫اﻟﻤﻮاﺻﻔﺎت‬
‫وﺹﻠﺔ ﻣﺮوﺣﺔ اﻟﻨﻈﺎم‬
‫ﻋﺪد ‪1‬‬
‫وﺹﻠﺔ ﻣﺴﺢ ‪CMOS‬‬
‫ﻋﺪد ‪1‬‬
‫ﻣﻨﻔﺬ ‪USB2.0‬‬
‫ﻋﺪد ‪2‬‬
‫یﺪﻋﻢ آﻞ ﻣﻨﻔﺬ ﻓﺘﺤﺘﻲ ‪ USB2.0‬ﺑﺎﻟﻠﻮﺣﺔ اﻷﻣﺎﻣﻴﺔ‬
‫ﻣﻨﻔﺬ ‪USB3.0‬‬
‫ﻋﺪد ‪1‬‬
‫یﺪﻋﻢ آﻞ ﻣﻨﻔﺬ ﻓﺘﺤﺘﻲ ‪ USB3.0‬ﺑﺎﻟﻠﻮﺣﺔ اﻷﻣﺎﻣﻴﺔ‬
‫ﻣﻨﻔﺬ اﻷﺣﻤﺮ ﺗﺤ ﺖ ﻣﺴ ﺘﻬﻠﻜﺔ‬
‫ﻋﺪد ‪1‬‬
‫ﻣﻨﻔﺬ ﻃﺎﺑﻌﺔ‬
‫ﻋﺪد ‪1‬‬
‫ﻣﻨﻔﺬ ﺗﺴﻠﺴﻠﻲ‬
‫ﻋﺪد‪1‬‬
‫ﻣﻨﻔﺬ ﺥﺮج ‪S/PDIF‬‬
‫ﻋﺪد ‪1‬‬
‫ﻣﻨﻔﺬ ﺗﻮﺹﻴﻞ اﻟﻄﺎﻗﺔ )‪24‬دﺑﻮس(‬
‫ﻋﺪد ‪1‬‬
‫ﻣﻨﻔﺬ ﺗﻮﺹﻴﻞ اﻟﻄﺎﻗﺔ )‪4‬دﺑﺎﺑﻴﺲ(‬
‫ﻋﺪد ‪1‬‬
‫ﻟﻮﺣﺔ ﻣﻔﺎﺗﻴﺢ ‪PS/2‬‬
‫ﻋﺪد ‪1‬‬
‫ﻣﻨﺎﻓﺬ ‪HDMI‬‬
‫ﻋﺪد ‪1‬‬
‫ﻣﻨﺎﻓﺬ ‪VGA‬‬
‫ﻋﺪد ‪1‬‬
‫ﻣﻨﺎﻓﺬ دﺧﻞ‪/‬ﺧﺮج ﻣﻨﺎﻓﺬ ‪DVI‬‬
‫ﻋﺪد ‪1‬‬
‫ﻣﻨﺎﻓﺬ ‪USB2.0‬‬
‫ﻋﺪد ‪2‬‬
‫ﻣﻨﺎﻓﺬ ‪USB3.0‬‬
‫ﻋﺪد ‪2‬‬
‫ﻣﻘﺒﺲ ﺹﻮت‬
‫ﻋﺪد ‪3‬‬
‫ﺣﺠﻢ اﻟﻠﻮﺣﺔ ‪ 220‬ﻣﻢ )ﻋﺮض( ‪ 244 X‬ﻣﻢ )ارﺗﻔﺎع(‬
‫‪45‬‬
‫یﺪﻋﻢ وﻇﻴﻔﺔ ﺥﺮج اﻟﺼﻮت اﻟﺮﻗﻤﻲ‬
‫ﻋﺪد ‪1‬‬
‫اﻟﻠﻮﺣﺔ اﻟﺨﻠﻔﻴﺔ ﻣﻨﻔﺬ ﺵﺒﻜﺔ اﺗﺼﺎل ﻣﺤﻠﻴﺔ‬
‫دﻋﻢ أﻧﻈﻤﺔ اﻟﺘﺸﻐﻴﻞ‬
‫ﻟﺘﻮﺹﻴﻞ اﻟﻄﺎﻗﺔ ﻟﻤﺮوﺣﺔ اﻟﻨﻈﺎم‬
‫‪Windows XP / Vista / 7‬‬
‫‪ATX‬‬
‫ﺑﺤﻘﻬﺎ ﻓﻲ إﺿﺎﻓﺔ أو إزاﻟﺔ اﻟﺪﻋﻢ ﻷي ﻧﻈﺎم ﺗﺸﻐﻴﻞ ﺑﺈﺧﻄﺎر أو ‪Biostar‬ﺗﺤﺘﻔﻆ‬
‫ﺑﺪون إﺧﻄﺎر‪.‬‬
Motherboard Manual
JAPANESE
仕様
Execute Disable Bit / Enhanced Intel SpeedStep® /
Socket 1155
CPU
Intel Core i7 / i5 / i3 / Pentium / Celeron プロ
セッサ
Intel Architecture-64 / Extended Memory 64
Technology / Virtualization Technology / Hyper
Threadingをサポートします
チップセット Intel B75
DDR3 DIMMスロット x 4
デュアル チャンネルモードDDR3メモリモジュール
最大メモリ容量32GB
DDR3 1066 / 1333 をサポート
メインメモリ
各DIMMは 512MB/1GB/2GB/4GB/8GB DDR3 DDR3 1600(Depending on CPU) をサポート
Super I/O
をサポート
登録済みDIMMとECC DIMMはサポートされません
IT8728
環境コントロールイニシアチブ、
もっとも一般に使用されるレガシーSuper I/O機
H/Wモニター
能を採用しています。
ファン速度コントローラ/ モニター
低ピンカウントインターフェイス
ITEの「スマートガーディアン」機能
最高3.0 Gb/秒 / 6.0 Gb/秒のデータ転送速度
SATA 2 & 3 統合シリアルATAコントローラ
LAN
SATAバージョン2.0 / 3.0仕様に準拠。
10 / 100 / 1000 Mb/秒のオートネゴシエーション
Realtek RTL 8111F
半/全二重機能
HDオーディ
ALC662
ハイデフィニションオーディオのサポート
オのサポート
5.1 チャンネルオーディオアウト
USB3.0
スロット
B75
データ転送速度最大600 MB /秒の
PCI Express Gen3 x16スロット
x1
PCIスロット
x2
PCI Express Gen2 x 1スロット
x1
オンボードコ SATA3コネクタ
x1
各コネクタは1つのSATA3デバイスをサポートします
ネクタ
SATA2コネクタ
x5
各コネクタは1つのSATA2デバイスをサポートします
フロントパネルコネクタ
x1
フロントパネル機能をサポートします
フロントオーディオコネクタ
x1
フロントパネルオーディオ機能をサポートします
CPUファンヘッダ
x1
CPUファン電源装置(スマートファン機能を搭載)
システムファンヘッダ
x1
システムファン電源装置
46
B75MU3+
仕様
CMOSクリアヘッダ
x1
USB2.0コネクタ
x2
各コネクタは2つのフロントパネルUSB2.0ポートをサポ
ートします
USB3.0コネクタ
x1
各コネクタは2つのフロントパネルUSB3.0ポートをサポ
ートします
消費者IRコネクタ
x1
プリンタポートコネクタ
x1
シリアルポート
x1
S/PDIFアウトコネクタ
x1
電源コネクタ(24ピン)
x1
電源コネクタ(4ピン)
x1
PS/2キーボード
x1
HDMIポート
x1
VGAポート
x1
背面パネル
DVI-Dポート
x1
I/O
LANポート
x1
USB2.0ポート
x2
USB3.0ポート
x2
オーディオジャック
x3
ボードサイズ 220 mm (幅) X 244 mm (高さ)
OSサポート Windows XP / Vista / 7
各コネクタは1つのプリンタポートをサポートします
デジタルオーディオアウト機能をサポートします
ATX
Biostarは事前のサポートなしにOSサポートを追加または
削除する権利を留保します。
2012/04/06
47
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement