Downloading
FOR YOUR PEACE OF MIND
OWNER’S MANUAL
VIDEO, MOVEMENT
& SOUND MONITOR
Model AC417
AC517
TABLE OF CONTENTS
WARNINGS...................................................................................................................................................3
Operating elements............................................................................................................................................5
Delivery content...................................................................................................................................................6
Camera Setup.......................................................................................................................................................7
Adhesive strips.....................................................................................................................................................7
Charging the Parent Unit..................................................................................................................................8
Powering the Camera.........................................................................................................................................8
Navigating the Parent Unit...............................................................................................................................9
Positioning the Movement Sensor Pad........................................................................................................9
Adjusting the Sensitivity of the Sensor Pad.............................................................................................10
Pausing/Restarting the Sensor Pad............................................................................................................10
Movement Monitoring....................................................................................................................................... 11
Additional Information...................................................................................................................................... 11
Troubleshooting................................................................................................................................................. 12
Limited warranty................................................................................................................................................ 13
Technical specifications................................................................................................................................... 13
OWNER’S MANUAL
KEEP YOUR OWNER’S MANUAL FOR FUTURE REFERENCE.
PLEASE READ THE WARNINGS AND INSTRUCTIONS CAREFULLY BEFORE ASSEMBLING & USING THE
PRODUCT.
FAILURE TO FOLLOW THE WARNINGS AND THE INSTRUCTIONS COULD RESULT IN SERIOUS INJURY OR
DEATH OR DAMAGES TO THE PRODUCT.
THE SENSOR PAD FEATURE IS NOT FOR USE WITH ADULTS, CHILDREN OR INFANTS OLDER THAN 24
MONTHS.
THE SENSOR PAD IS NOT INTENDED TO BE USED TO DETERMINE
IF A CHILD IS OUT OF THE CRIB.
WARNING
Adult assembly required.
Keep small parts away from children when assembling.
We, at Angelcare®, stand behind all of our products.
If you are not completely satisfied or have any questions,
United States and Canada: Please contact us at: angelcare@cdecinc.ca
Other countries: Please contact your local distributor.
FCC AND IC REGULATIONS
RF radiation exposure statement
The Nursery Unit complies with FCC RF radiation exposure limits set forth for an uncontrolled environment.
Caution: To maintain the compliance with the FCC’s and Industry Canada’s RF exposure guideline, install
the Nursery Unit at least 20 cm from ALL persons. The transmitter of this device must not be co-located or
operating in conjunction with any other antenna or transmitter.
Industry Canada
This product meets the applicable Industry Canada technical specifications.
CAN ICES-3 (B)/NMB-3 (B)
2
WARNINGS
1. T H I S
PRODUCT
C A N N OT
R EPL AC E
RESPONSIBLE ADULT SUPERVISION. This product
is designed to aid in the monitoring of your child.
When using the monitor, you must still provide the
supervision necessary for the continued safety
of your child. Monitoring of premature babies,
or those considered to be at risk, should always
be carried out under the supervision of a health
professional. This monitor SHOULD NOT be used
as a medical device, nor as a device to prevent
Sudden Infant Death Syndrome (SIDS).
2. WARNING Strangulation Hazard — Children
have STRANGLED in cords. Keep adapter cords
o ut of th e re a ch of
children (more than 1
meter away). NEVER use
Sensor Pad(s) without
t h e p r o te c t i ve c o r d
covering.
Check
protective cord covering
before
each
use.
Immediately discontinue
use of Sensor Pad(s) if
protective covering is
damaged or broken.
3. Never use extension cords with adapters. ONLY
use the adapters provided.
4. When an adapter is plugged into an electrical
outlet, DO NOT touch the exposed end.
5. ALWAYS be sure that both the transmitter and
receiver are working properly and are within range
of each other. Test the monitor before first use,
periodically and when changing location of the
Nursery Unit.
6. ALWAYS be sure to immediately check on baby
whenever an alarm sounds.
7. DO NOT use monitor near water (such as bath
tub, sink, etc.).
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
DO NOT EXPOSE TO RAIN OR MOISTURE
8. Keep monitor AWAY from heat sources (such
as stoves, radiators, etc.).
9. ALWAYS place both the Nursery Unit and the
Parent Unit on a flat surface in an upright position
and allow for proper ventilation. DO NOT place
on sofas, cushions, beds, etc. which may block
ventilation.
10. This monitor uses public airwaves to transmit
signals. The Parent Unit may pick up signals or
interference from other nursery monitors in your
area. Your monitor may even be picked up by
other households. To protect your privacy, make
sure both units are turned OFF when not in use. If
you experience interference, change the channel
on both units.
11. This product is NOT a toy. DO NOT allow
children to play with it.
12. This product contains small parts. Adult
assembly required. Exercise care when unpacking
and assembling the product and keep small parts
away from children.
E
N
13. When using the monitor, the room temperature
should be between 10°C and 40°C.
BATTERY WARNING
14. D a n g e r of ex p l o s i o n if b a t te r i e s a re
incorrectly replaced. The Parent Unit battery is a
replaceable Li-Ion battery. Only use the Angelcare
recommended replacement battery. In both units,
DO NOT mix old and new batteries. DO NOT mix
alkaline, standard or rechargeable batteries.
Insert batteries with correct polarity. DO NOT
short-circuit supply terminals. ONLY use the
recommended batteries or equivalent (volts and
size) and the correct adapter. Remove batteries in
both units when product is stored for long periods
of time or when batteries are exhausted. Dispose
exhausted batteries properly. Keep all batteries
away from children.
15. IMPORTANT SAFETY INSTRUCTIONS
15.1 Heed all warnings – All warnings on the
product and in the operating instructions should
be adhered to.
15.2 Follow all instructions – All operating and
use instructions should be followed.
15.3 Water and moisture - DO NOT use this
apparatus near water. For example, near a bath
tub, wash bowl, kitchen sink, laundry tub, in a wet
environment or near a swimming pool and the
like. Care should be taken so that objects DO NOT
fall onto units and that liquids are not spilled into
either unit or Sensor Pad through its openings.
15.4 Cleaning - Disconnect all units before
cleaning. DO NOT immerse in water any part of
the monitor. Clean only with dry cloth.
15.5 Ventilation - DO NOT block any ventilation
openings. Allow for proper ventilation when units
are in use. DO NOT cover the Nursery Unit or the
Parent Unit with any object such as a blanket.
DO NOT place it in a drawer or in any location
which would muffle the sound or interfere with
the normal flow of air.
15.6 Heat sources - DO NOT install near any heat
sources such as radiators, heat registers, stoves,
TVs or other apparatus (including amplifiers)
that produce heat. Heat can damage the case or
electrical parts.
15.7 Power cord protection - Protect the Sensor
Pad cord and Adapter’s power cord from being
walked on or pinched by furniture or other items –
Power supply cords should be routed so that they
are not likely to be walked on or pinched by items
upon or against them, paying particular attention
to cords and plugs, convenience receptacle, and
the point where they exit from the product.
The socket outlet shall be installed near the
equipment and shall be easily accessible. Make
sure to plug the adapter to the socket outlet
nearest to the equipment and that is easily
accessible. To disconnect from mains, unplug
the adapter.
15.8 Accessories - O nly use at tachm e nt s/
3
accessories specified by the manufacturer. DO
NOT place this product on an unstable cart,
stand, tripod, bracket or table. The product may
fall, causing serious injury to a child or adult and
serious damage to the product. Use ONLY with a
cart, stand, tripod, bracket or table recommended
by the manufacturer or sold with the product.
Any mounting of the product should follow the
manufacturer’s instructions.
15.9 Unplug this appliance during lightning storms
or when not used for long periods of time.
15.10 Servicing - DO NOT attempt to service
this product yourself as opening or removing
covers (except battery door) may expose you to
dangerous voltage or other hazards.
15.11 Replacement parts - When replacement
parts are required, be sure the replacement parts
specified by the manufacturer have the same
characteristic as the original part. Unauthorized
substitution may result in fire, electric shock or
other hazards.
15.12 Usage - This baby monitor is intended as
an aid. It is NOT a substitute for responsible and
proper adult supervision and should not be used
as such. Use this appliance ONLY for its intended
use as described in this manual.
15.13 Power Sources - Operate this product only
from the type of power source indicated on the
type plate of the adaptor. If you are unsure of the
type of power supply to your home, consult your
dealer or local power company.
15.14 Overloading - DO NOT overload wall
outlets, extension cords or integral convenience
receptacles as this can result in a risk of fire or
electric shock.
15.15 Object and Liquid Entry - NEVER push
objects of any kind into this product through
casing slots as they may touch dangerous voltage
points or short out parts that could result in a risk
of fire or electric shock. NEVER spill liquid of any
kind on the product.
15.16 Antenna - The antenna used for this
transmitter must be installed to provide a
separation distance of at least 20 cm from all
persons and must not be collocated or operating in
conjunction with any other antenna or transmitter.
15.17 Power Lines - An outside antenna system
should NOT be located in the vicinity of overhead
power lines or other electric light or power circuit,
or where it can fall into such power lines or circuits
as contact with them may be fatal.
4
15.18 Vibration Source - When the monitor is
in use, DO NOT use a crib mobile or other crib
accessories that may produce vibrations. Other
sources of vibrations may include fans, washing
machines, loud music, etc. These sources of
vibration may interfere with the performance of
your Angelcare ® monitor and the alarm will not
sound if it continues to detect any movement
other than your baby’s. Be sure all vibration
sources are eliminated before using the monitor.
You may experience false alarms for several
reasons . The most common reason is the
Nursery Unit has not been turned OFF after
you have removed your baby from the crib.
Another reason is the Sensor Pad has not
been placed under the mattress properly.
Be sure the Sensor Pad is on a flat, firm surface
with the printed side facing up. The sensitivity
level may also need to be adjusted. Refer to Step
5.1. Always be sure to immediately check on baby
whenever an alarm sounds.
15.19 Sensor Pad - Your Sensor Pad can be used
in any crib that is stationary. If the crib has a
spring or slat base, place a hard board between
the crib base and the Sensor Pad measuring
at least 33 x 33 cm and 6 mm thick. Only use
your Angelcare ® monitor in a stationary sleeping
environment such as a crib where the Sensor
Pad can rest on a completely flat, firm surface.
The sensor pad is made of plastic and does not
permit the air to circulate. Therefore, mildew
build up could develop underneath the mattress
in the sensor pad area. We suggest rotating
the mattress regularly to prevent any mildew.
16. I M P O R TA N T S A F E T Y I N S T R U C T I O N S
RELATED TO USE OF BATTERIES
16.1 Use ONLY the type and size of batteries
specified in the owner’s manual. There is a risk
of explosion if batteries are replaced with an
incorrect type.
16.2 Charge the battery for 9 hours prior to first
use. Be sure to have the monitor in the OFF
position during this period. ONLY use the adapters
included with your monitor.
16.3 DO NOT use these adapters with any other
equipments.
16.4 When unplugging the adapter from the
Nursery Unit, be sure it is switched to the OFF
position. If it isn’t, the unit will revert to battery
mode if batteries are installed.
16.5 DO NOT use rechargeable batteries in the
Nursery Unit. Use alkaline batteries ONLY.
16.6 DO NOT dispose batteries in fire. They may
explode. Check with local regulations for possible
special disposal instructions.
16.7 Exercise care in handling batteries in order
not to short out the batteries with conducting
materials such as rings, bracelets and keys.
Overcharging, short circuiting, reverse charging,
mutilation, or incineration of batteries must be
avoided to prevent one or more of the following
occurrences: release of toxic materials, release of
hydrogen and/or oxygen, gas and rise in surface
temperature.
16.8 DO NOT attempt to recharge batteries
provided with or identified for use with this
product that are not intended to be charged.
The batteries may leak corrosive electrolyte or
explode.
16.9 DO NOT attempt to rejuvenate the batteries
provided with or identified for use with this
product by heating them. Sudden release of
battery electrolyte may occur, causing burns or
irritation to eyes or skin.
16.10 If and when necessary, the batteries must
be replaced with identical new ones or equivalent
(volts and size). If a battery to be replaced is
connected with other batteries in series, replace
the other batteries at the same time as well. DO
NOT mix old and new batteries.
16.11 Reverse polarity installation of the batteries
in the end product must be avoided. Reverse
insertion of batteries can cause charging, and
that may result in leakage or explosion.
harmful interference to radio communications.
16.12 Remove batteries from both units if you store
the product over 30 days because the batteries
could leak and damage the product.
17.3 H oweve r, th e re is n o g ua ra nte e th at
inter ference will not occur in a par ticular
installation. If this equipment does cause harmful
interference to radio or television reception, which
can be determined by turning the equipment OFF
and ON, the user is encouraged to try to correct
the interference by one or more of the following
measures:
16.13 Discard ‘dead’ batteries as soon as possible
since ‘dead’ batteries are more likely to leak in a
product. If a battery has leaked or vented, it should
be replaced immediately using protective gloves.
16.14 DO NOT store this product, or the batteries
provided with or identified for use with this
product, in high-temperature areas.
FCC WARNING
17. (North America Only)
17.1 Warning: Changes or modifications to this
equipment not expressly approved by the party
responsible for compliance could void the user’s
authority to operate the equipment.
17.2 NOTE: This equipment has been tested
and found to comply with part 15 of the FCC
Rules and the Industry Canada license-exempt
RSS standard(s). These limits are designed to
provide reasonable protection against harmful
interference in a residential installation. This
equipment generates, uses and can radiate radio
frequency energy and, if not installed and used
in accordance with the instructions, may cause
E
N
• Reorient or relocate the receiving
antenna.
• Increase the separation between
the equipment and receiver.
• Connect the equipment into an
outlet on a circuit different from that
to which the receiver is connected.
• Consult the dealer or an experienced
radio/TV technician for help.
17.4 This device complies with the part 15 of the
FCC Rules and the Industry Canada license exempt RSS standards(s). Operation is subject
to the following two conditions:
(1) This device may not cause harmful interference,
and
(2) This device must accept any interference
received, including interference that may cause
undesired operation.
Operating elements
Power
On/Off
Power indicator
Power
On/Off
Visual sound indicator
Sensor pad
pause
Microphone
Volume
control +/(on the side)
Micro USB
charging port
(on the side)
Folding stand (on backside)
Rechargeable battery
compartment (on backside)
Parent unit
Micro USB
charging port
Room
temperature
display
Camera
5
Delivery content
Touch control parent unit
AC adapter
(for parent unit)
Camera
Lithium ion battery pack
(for parent unit)
Tabletop stand
(for camera)
AC adapter
(for camera)
* Always place printed side up *
Wall mount
(for camera)
with hardware
Flat micro USB cable
(for camera adapter)
Adhesive strips
(for flat micro USB cable)
Wireless movement sensor
6
Camera Setup
The camera can be hung on a wall or placed on a flat, stable surface.
Consider you will need a suitable wall outlet within reach, be mindful the
camera and cord should always be more than 3 feet away from children.
E
N
Strangulation Hazard: Children have been
STRANGLED by cords. Keep cords out of the
reach of children (more than 3 feet away).
Must be more
than 3 feet away
Must be more
than 3 feet away
Adhesive strips
Six strips of double-sided adhesive tape have been included for use when
wall-mounting the camera.
These strips are intended to keep the USB cable neatly in place along the wall
from the camera to the AC adapter.
a) The two sides of the tape have different strengths so be sure to place the
side which is labeled “3M” against the wall.
b) It is recommended to test the tape in an obscure location on the wall first
to ensure there will not be any damage.
Note:
Each time you power on your camera, the internal thermometer will need to calibrate to
ensure accuracy. This automatic process will take approximately 30 minutes. The color
changing temperature display, by default, will be turned “off.” You may turn this feature
“on” in the settings mode on your parent unit.
2:04
63°F
68°F
79°F
7
Charging the Parent Unit
• Prior to the first use, we recommend that you charge the parent unit for 8 hours.
AC410/AC417
• Unlock the PU
battery compartment on the backside and remove the cover. Insert the provided
08/04/2016
rechargeable
battery into the compartment. Contacts of the battery and the contacts in the
compartment must be aligned.
• To turn the parent unit On/Off, press and hold the power button for 2 - 3 seconds.
Battery compartment lock
+
VOLUME
-
Powering the Camera
Your camera and parent unit come pre-paired, so you should see video within 3 - 4 seconds of
turning on the units. The camera connection signal strength icon will appear in the status bar.
Press and hold
for 2-3 seconds
ON
OFF
Camera connection signal strength
2:04
8
68°F
Navigating the Parent Unit
In the top section of your screen you will see a blue bar with all of the necessary information
concerning the status of units, alerts, temperature, and your chosen settings.
Time/Temperature
Active camera
E
N
Camera connection
signal strength
Volume level
2:04
68°F
Battery status
of parent unit
Adjust screen
brightness
Pause sensor pad
Zoom
Main settings menu
Activate parent
unit microphone
Show reporting
Select Camera
Positioning the Movement Sensor Pad
When using the sensor pad for the first time, you will need to insert the provided CR3032 battery.
1. Remove the battery cover using a coin. Turn in the direction of the arrow.
2. Place the CR3032 battery into position and replace the battery cover, making sure to lock
correctly. The sensor pad is now ON.
3.Position the sensor pad, printed side up, under the mattress in center of the crib.
4.Ensure your sensor pad is connected by rubbing your hand on the mattress. Verify the wireless
sensor pad icon is on the status bar of your parent unit.
Note: To “pause” the alarm refer to the next page.
9
Note:
•
•
•
If the bottom of the crib is not a solid, stable surface you will need to place a hard support
board (not included) underneath the sensor pad to ensure correct operation of the system.
Place the sensor pad directly underneath the mattress (and on top of
support board, if needed) in the center of the crib. Make sure there is
nothing between the mattress and sensor pad to interfere with operation.
The sensor pad is designed to work with all regulatory standard mattresses.
It is not compatible with hollow core mattresses or mattresses containing
memory foam that comes in contact with the sensor pad.
• Never immerse the sensor pad in water or other liquids!
Strangulation Hazard: Children have been STRANGLED by cords.
• Because of the serious strangulation risk to infants and toddlers, parents and caregivers
should never place the camera within 3 feet (0.9 m) of a crib.
Adjusting the Sensitivity of the Sensor Pad
• To ensure adequate monitoring of your child’s movements, you can adjust the sensitivity of the sensor pad in the
main settings menu.
• Set a high sensitivity for a newborn and a lower sensitivity as the child grows and gains weight. A thicker mattress
will also need a higher sensitivity.
• Alarm will sound if there is no movement after 20 seconds.
2:04
68°F
Main settings menu
Pausing/Restarting the Sensor Pad
• If you remove baby from the crib, e.g. for feeding or comforting, remember to pause the sensor pad. That can
be done from the parent unit by pressing OK and then navigate to the pause sensor to activate / deactivate or
from the camera by pressing the pause button on the top right of the unit.
• Don’t forget to restart by utilizing the same methods to re-engage the sensor pad.
• If you do not pause the sensor pad, the alarm will sound if there is no movement after 20 seconds.
Pause sensor pad
2:04
Camera
10
Parent unit
68°F
Movement Monitoring
Angelcare monitors are designed to sense baby’s slightest movements and sound an
alarm if no movement is detected after 20 seconds. This monitor is also equipped with
“Activity Analytics” which track, record and report on baby’s bigger movements (like
restlessness, rollovers and kicks).
E
N
The monitor records data every ten seconds, and if one or more “big movements” is detected, the
system records your baby as being “active” during that time period.
Three times every hour, the system compiles the collected data and a “movement activity report”
can be viewed on the parent unit.
Activity analytics and room temperature tracking give you insight into your little one’s activity
level during sleep, helping you to better adapt routines and respond to their needs.
68°F
28/10/2016
28
28
28
22
14
Additional Information
Product Registration
Registering your Angelcare monitor allows us to send you important product and safety updates.
To register your product online, please visit: www.angelcarebaby.com/product-registration
Customer Support
To obtain a full user guide, please visit: www.angelcarebaby.com/customer-support/manuals
For additional customer support, please contact us at: Email: angelcare@cdecinc.ca Phone: 1-877-281-8827
1 Year Limited Warranty - visit www.angelcarebaby.com, call us at the number above, or write us at the address below for a copy
of the complete warranty statement. Please keep this quick start guide for future reference.
Angelcare Monitors Inc., 201 Boulevard de l’Industrie, Local 104, Candiac, Quebec, J5R 6A6 Canada.
Designed in Canada. Made in China.
While Angelcare intends to provide peace of mind to our consumers, monitoring of a premature baby or babies considered to be at
risk should be carried out only under the supervision of a doctor or health care professional. This product is not intended to diagnose,
treat, mitigate, cure or prevent any disease or condition. This monitor should NOT be used to prevent Sudden Infant Death Syndrome
(SIDS). Vibration Source - When the monitor is in use, DO NOT use a crib mobile or other crib accessories that may produce vibration.
Other sources of vibration may include fans, washing machines, loud music, etc. These sources of vibration may interfere with
the performance of your Angelcare monitor and the alarm will not sound if it continues to detect any movement other than your
baby’s. Be sure all vibration sources are eliminated before using the monitor.
The Angelcare sensor pad feature is not designed for use with adults, children or infants over 24 months. This product is intended
to be used only for parental reassurance to monitor your baby’s movements.
11
TROUBLESHOOTING
TAKING CARE OF YOUR RECHARGEABLE BATTERIES
• Ensure that you fully charge your batteries for 8 hours before their first use.
• To maintain maximum battery life it is recommended that you fully discharge your batteries periodically.
If your Parent Unit is not in use, please turn it OFF.
FALSE ALARMS
Turn OFF the Nursery Unit.
Verify the connection between the Sensor Pad and the Nursery Unit. Unplug and reconnect the cord.
Make sure there is no bedding between the mattress and the Sensor Pad.
If the crib has a spring or slat base, place a hardboard between the crib base and the Sensor Pad
measuring at least 13 in x 13 in x ¼ in thick.
• Make sure the Sensor Pad is positioned as described under the setup requirements. Sensitivity
may need to be adjusted.
•
•
•
•
ALARM WILL NOT SOUND
• Avoid contact with the crib when the monitor is ON.
• Place crib near a solid supporting wall to avoid Sensor Pad from detecting movement from outside the crib.
• You may need to decrease the sensitivity.
NO SOUND IS BEING TRANSMITTED
• Check the volume level on the parent unit and the camera to ensure they are set to an appropriate level
• Try bringing the parent unit closer to the camera to see if you get sound
• Charge the parent unit.
WEAK RECEPTION
•
•
•
•
Bring units closer together.
Change the position of one or both units.
Place units on a flat surface away from baby’s reach.
Recharge the Parent Unit.
STATIC, DISTORTION, INTERFERENCES
(FROM OTHER MONITORS, WIRELESS PHONES, WALKIE-TALKIES, ETC.)
• Rotate Parent Unit or move it away from source of interference.
FEEDBACK (LOUD NOISES EMITTED FROM THE PARENT UNIT)
• Move units farther apart (at least 3 meters).
• Decrease volume on Parent Unit.
THE PARENT UNIT SCREEN IS BLACK (PARENT UNIT IS OFF)
• Turn the Parent Unit back ON by pushing and holding the POWER ON/OFF button for 2 seconds.
• Recharge the Parent Unit.
12
LIMITED WARRANTY
Angelcare® warrants to the original owner of this
product that Angelcare® video, movement and sound
monitor (model AC1300) is free from any material
and workmanship defects, for a period of two (2)
years from the date of the original purchase. If this
monitoring system fails to function properly when
used as directed under normal conditions within
the two years period, Angelcare® will either repair or
replace the product, at our discretion, free of charge.
Please contact your distributor.
The product must be accompanied by a proof of
purchase, either a bill of sale or other proof that the
monitoring system is within the warranty period.
Angelcare® will bear the cost of repairing or replacing
the product and shipping it back to you.
This warranty does not apply to a product which
has been damaged as a result of improper
maintenance, an accident, improper voltage supply
or any other form of misuse. The warranty is also
void if the owner repairs or modifies the product in
any way. Angelcare® is not liable for any incidental
or consequential damages with regard to this
product. The warranty also excludes any liability
other than what is stated above. No other warranty
is given.
This warranty does not cover products and
accessories which are not Angelcare-branded, or
any problems that result from usage that is not in
accordance with product instructions, failure to
follow the product instructions, or problems caused
by using accessories, parts or components not
supplied by Angelcare.
E
N
LEGAL RIGHTS VARY FROM COUNTRY TO
COUNTRY. SOME COUNTRIES DO NOT ALLOW
THE EXCLUSION OR LIMITATION OF INCIDENTAL
OR CONSEQUENTIAL DAMAGES, SO THE ABOVE
LIMITATIONS MAY NOT APPLY TO YOU.
WE ARE NOT IN ANY WAY RESPONSIBLE FOR ANY
OUTCOME RESULTING FROM THE USE OF THIS
PRODUCT.
IMPORTANT! This Angelcare® monitor is a personal
care product. Please do not return this product
to the store. If you have questions or need help,
please call your distributor before returning this
product.
TECHNICAL SPECIFICATIONS
Range:
Open field (Open area without obstructions):
up to 250 meters.
Batteries:
Number of Channels:
USA/Canada: 24 channels.
Europe: 64 channels.
• DO NOT mix alkaline standard
(carbon-zinc), or rechargeable
(NI-CD, NIMH, etc.) batteries.
Power Supply:
1 included Li-Ion battery (parent unit)
100 - 240 VAC / 5 VDC adapter for the parent unit
100 - 240 VAC / 5 VDC adapter for the camera
1 included rechargeable Li-ion battery and
100 - 240 VAC / 5 VDC adapter for the parent unit.
Caution: To reduce the risk of electric shock, do
not expose this product to rain or moisture.
Danger of explosion if batteries are incorrectly
replaced. The battery included for the Parent Unit
is a user replaceable Li-ion rechargeable battery,
manufactured by SPRINGPOWER TECHNOLOGY
(SHENZHEN) COMPANY LIMITED. Only use the
Angelcare recommended replacement battery.
To obtain information on replacement batteries
please contact Angelcare customer service:
www.angelcarebaby.com or contact your local
distributor. Instructions will be included with
the replacement battery. Dispose of exhausted
batteries properly according to your local
ordinances. Keep all batteries away from children.
• DO NOT mix old and new batteries.
Transmission:
Data transmission between the Parent
Unit and the Nursery Unit is made on the 2.4GHz
frequency.
Hereby, Angelcare Monitors Inc., declares this
baby monitor is in compliance with the essential
requirements and other relevant provisions of
Directive 1999/5/EC.
The EU declaration of conformity can be obtained
at: www.angelcarebaby.com.
PROTECT THE ENVIRONMENT
This electronic equipment contains reusable
material and must not be disposed with
domestic waste. Please take it to a collecting
point for electric and electronic equipment
(ask your local authorities for details).
13
www.angelcarebaby.com
IM1300-INT-082216
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising