#20

Opaque

#10 Clear

SLIM LINE

FILTER HOUSINGS

t4MJNEFTJHOSFEVDFTTQBDFSFRVJSFEGPSJOTUBMMBUJPOXJUIPVUTBDSJmDJOHDBQBDJUZ t"WBJMBCMFJOBOEMFOHUIT t'%"(SBEF t0QUJPOBMQSFTTVSFSFMJFGCVUUPOPOJOMFUTJEFPGDBQ t-FBLQSPPGTFBMXJUIUPQTFBUFEPSJOH t"WBJMBCMFXJUIDMFBSPSPQBRVFTVNQT

Slim Line ® filter housings are available in either reinforced polypropylene or clear Styrene-

Acrylonitrile (SAN) in 5", 10" and 20" lengths. The black or blue reinforced polypropylene housing caps are available with 1/4", 3/8" or 1/2" NPT connections. Four bosses are molded into every cap for mounting purposes.

They are equipped with a black, reinforced polypropylene cap and offer an optional pressure-relief button on the inlet side to relieve pressure inside the housing when changing filter cartridges.

Slim Line ® filter housings are an excellent choice for low-flow applications and when space and chemical compatibility are primary concerns.

Opaque Slim Line ® Filter Housings

Molded from rugged reinforced polypropylene, Opaque Slim Line ® filter housings offer outstanding chemical compatibility and are ideal for use in a variety of low-flow applications. These applications include under-sink and countertop residential filtration, pre- and post-reverse osmosis filtration, recreational vehicle filtration, food service and humidifying systems.

Clear Slim Line ® Filter Housings

offer on-site examination of flow, performance, and cartridge life.

They are also ideal for a variety of applications.

#5 Clear

#5 Opaque

#10

Opaque

Manufactured of clear Styrene-

Acrylonitrile (SAN), the sumps are annealed to relieve stress, adding clarity and strength.

SLIM LINE

'JMUFS)PVTJOHT

4MJN-JOF

'MPX3BUFoHQN -QN

)PVTJOH4QFDJmDBUJPOTBOE1FSGPSNBODF%BUB

.PEFM

.BYJNVN%JNFOTJPOT

#5 Clear

#10 Clear

#5 Opaque

#10 Opaque

#20 Opaque

7 3 ⁄

" x 4 5 ⁄

" (187 mm x 118 mm)

⁄

" x 4

⁄

" (308 mm x 118 mm)

7" x 4 3 ⁄

" (178 mm x 111 mm)

11 3 ⁄

" x 4 3 ⁄

" (299 mm x 111 mm)

21 7 ⁄

" x 4 3 ⁄

" (556 mm x 111 mm)

.BUFSJBMTPG$POTUSVDUJPO

Housing

Cap

SAN (Clear) or Polypropylene (Opaque)

Reinforced Polypropylene

Button Assembly

O-Ring

300-series Stainless Steel, EPDM, and Polypropylene

#VOB/

Maximum Temperature

Maximum Pressure

125ºF (51.7ºC)

125 psi (8.62 bar)

CAUTION: Protect against freezing to prevent cracking of the filter and water leakage.

The 158005, 158006, 158114, 158115, 158120, 158125,

158126, 158128, 158129, 158131,158149, 158195,

158196, 158204, and 158205 are Tested and Certiﬁed by

NSF International to NSF/ANSI Standard 42 for material and structural integrity requirements.

*OJUJBMå1 QTJ!'MPX3BUF HQN

1/4" NPT–2 psi @ 3 gpm (0.14 bar @ 11 Lpm)

3/8" NPT–2 psi @ 5 gpm (0.14 bar @ 19 Lpm)

1/4" NPT–2 psi @ 3 gpm (0.14 bar @ 11 Lpm)

1/2" NPT–2 psi @ 5 gpm (0.14 bar @ 19 Lpm)

*OEJBOB"WFOVFr10#PYr4IFCPZHBO8JTDPOTJO

$VTUPNFS4FSWJDFr'BYrTVQQPSUTQFDJBMJTU!QFOUFLàMUSBUJPODPN

*OUFSOBUJPOBMr'BYrJOUFSOBUJPOBM!QFOUFLàMUSBUJPODPN www.pentekfiltration.com Printed in USA MR06 310050

3G SLIM LINE

FILTER HOUSINGS

tJODIIPVTJOHTBWBJMBCMFXJUIDMFBSPSPQBRVFTVNQ t#VUUSFTTUISFBETGPSBEEJUJPOBMTUSFOHUIBOEFBTJFSDBSUSJEHFDIBOHFT t+PIO(VFTUBOE/15UISFBEFEDPOOFDUJPOTPGGFSFEJOJODIJODIBOEJODI t$BQTUZMFTJODMVEFNPVOUJOHCPTTJOUFHSBMCSBDLFUNFUFSNPVOUBOEPQUJPOBMQSFTTVSFSFMJFGCMFFEWBMWF t)PVTJOHBDDFQUTPVSQSPQSJFUBSZ4FBM4BGF TM EPVCMFPSJOHTFBMJOHDBSUSJEHFTBTXFMMBT%0& EPVCMFPQFOFOEDBSUSJEHFT t-FBLQSPPGTFBMJOHXJUIBUPQTFBUFEnPBUJOH#VOB/PSJOH

Slim Line ® housings are the perfect choice for low-flow filtration applications. Their slim design and high chemical compatibility make them ideal for those challenging applications.

Caps are manufactured from reinforced polypropylene in black, blue, and white. Standard NPT threaded and John Guest connections are available with 1/4-inch,

3/8-inch and 1/2-inch connections.

Three different style caps add to the flexibility of these housings.

The mounting boss cap features bosses molded in to the cap. This allows the housing to be mounted to a single bracket or a multiple housing bracket.

The integral bracket cap does not require a separate bracket as the bracket is part of the cap. This feature saves valuable time during installation.

Take the guesswork out of when to change your cartridge by using the meter mount cap. These gauges indicate when the cartridge is dirty and allow you to get the most out of your cartridges.

Pressure relief buttons are another option with the Slim Line ®

3G housings. Placed on the inlet side, the pressure-relief button helps reduce the pressure in the housing when changing the cartridge.

Housings are available with either clear or opaque sumps. The clear housings are manufactured of Styrene-

Acrylonitrile (SAN) and are stress relieved through a special process for added strength and clarity. Clear housings offer on-site examination of the flow, cartridge life and performance.

Opaque housings are molded from reinforced polypropylene and offer outstanding chemical compatibility.

Typical applications for the 3G Slim

Line ® housings include, but are not limited to, undersink residential filtration, pre- and post reverse osmosis systems, recreational vehicle filtration, and food service.

* U.S. Patent No. D 455,194 S and D 456,486 S

(4MJN-JOF

'JMUFS)PVTJOHT

143549 **

)PVTJOH

143550 **

* Shown with differential gauge.

Gauges are not performance tested or certified by NSF.

** Gauges sold seperately.

Filter Housings Tested and Certiﬁed by NSF

International to NSF/ANSI Standard 42 for material and structural integrity requirements.

'MPX3BUFoHQN -QN

Housing Speciﬁcations and Performance Data

Model

Maximum

Dimensions

Initial

P (psi)

@ Flow Rate (gpm)

1/4-inch #10 3G Slim Line w/MB

1/4-inch #10 3G Slim Line w/IB

3/8-inch #10 3G Slim Line w/MB

3/8-inch #10 3G Slim Line w/IB

1/2-inch #10 3G Slim Line w/MB

1/2-inch #10 3G Slim Line w/IB

11 3 ⁄

" x 4 3 ⁄

(298 mm x 121 mm)

13 3 ⁄

" x 5 ⁄ 3

(340 mm x 137 mm)

11 3 ⁄

" x 4 ⁄ 3

(298 mm x 121 mm)

13 3 ⁄

" x 5 3 ⁄

(340 mm x 137 mm)

11 3 ⁄

" x 4 3 ⁄

(298 mm x 121 mm)

13 3 ⁄

" x 5 3 ⁄

(340 mm x 137 mm)

2 psi @ 3 gpm

(0.14 bar @ 11 L/min)

2 psi @ 3 gpm

(0.14 bar @ 11 L/min)

2 psi @ 5 gpm

(0.14 bar @ 19 L/min)

2 psi @ 5 gpm

(0.14 bar @ 19 L/min)

2 psi @ 5 gpm

(0.14 bar @ 19 L/min)

2 psi @ 5 gpm

(0.14 bar @ 19 L/min)

1/2-inch #10 3G Slim Line w/IB & MM

13 3 ⁄

" x 5 3 ⁄

(340 mm x 137 mm)

2 psi @ 5 gpm

(0.14 bar @ 19 L/min)

MB = Mounting Bosses for MC-1A Bracket, 1B = Integral Bracket, MM = Meter Mount

*Height does not include meter. Add 1 3 ⁄

-inch for 143549 gauge and 1/2-inch for 143550 gauge.

.BUFSJBMTPG$POTUSVDUJPO

Housing

Cap

Button Assembly

O-Ring

Polypropylene (Opaque) or Styrene Acrylonitrile (Clear)

Reinforced Polypropylene

TFSJFT4UBJOMFTT4UFFM&1%.BOE1PMZQSPQZMFOF

#VOB/

$"65*0/1SPUFDUBHBJOTUGSFF[JOHUPQSFWFOUDSBDLJOHPGUIFàMUFSBOEXBUFSMFBLBHF

Maximum

Temperature

125°F

(51.7°C)

125°F

(51.7°C)

125°F

(51.7°C)

125°F

(51.7°C)

125°F

(51.7°C)

125°F

(51.7°C)

125°F

(51.7°C)

Maximum

Pressure

125 psi

(8.62 bar)

125 psi

(8.62 bar)

125 psi

(8.62 bar)

125 psi

(8.62 bar)

125 psi

(8.62 bar)

125 psi

(8.62 bar)

125 psi

(8.62 bar)

¥1FOUBJS'JMUSBUJPO*OD

*OEJBOB"WFOVFr10#PYr4IFCPZHBO8JTDPOTJO

$VTUPNFS4FSWJDFr'BYrTVQQPSUTQFDJBMJTU!QFOUFLàMUSBUJPODPN

*OUFSOBUJPOBMr'BYrJOUFSOBUJPOBM!QFOUFLàMUSBUJPODPN

XXXQFOUFLàMUSBUJPODPN 1SJOUFEJO64"+&

#20

Opaque

#10

Opaque

STANDARD FILTER HOUSINGS

t*EFBMGPSBXJEFSBOHFPGBQQMJDBUJPOTJODMVEJOHSFTJEFOUJBMDPNNFSDJBMBOEJOEVTUSJBM t"WBJMBCMFJOwBOEwMFOHUIT t0QUJPOBMQSFTTVSFSFMJFGCMFFECVUUPOPOJOMFUTJEFPGDBQ t5IJDLXBMMTGPSJODSFBTFETUSFOHUI t-FBLQSPPGTFBMJOHXJUIUPQTFBUFE#VOB/0SJOH t"WBJMBCMFXJUIDMFBSPSPQBRVFTVNQT

Standard filter housings are manufactured of a durable polypropylene or clear FDAcompliant Styrene-Acrylonitrile

(SAN). All are equipped with 3/4"

NPT inlet and outlet ports. Standard filter housings are available in both 10" and 20" lengths and will accommodate a wide range of 2

⁄

" to 2 7 ⁄

" diameter cartridges. The reinforced polypropylene cap and offers an optional pressure-relief button on the inlet side to relieve pressure inside the housing when changing filter cartridges.

Reinforced polypropylene housings have excellent chemical resistance and are ideal for many residential, commercial and industrial applications. Clear sumps offer onsite examination of the cartridge.

Opaque Standard Filter Housings

are molded from rugged reinforced polypropylene. They offer outstanding chemical compatibility and are ideal for use in a variety of low-flow applications. These applications include under-sink and countertop residential filtration, pre- and post-reverse osmosis filtration, recreational vehicle filtration, food service and humidifying systems.

Clear Standard Filter Housings

offer on-site examination of flow, performance, and cartridge life.

They are also ideal for a variety of applications.

#10

Clear

Manufactured of clear, Styrene-

Acrylonitrile (SAN), the sumps are annealed to relieve stress, adding clarity and strength.

STANDARD

'JMUFS)PVTJOHT

'MPX3BUFoHQN -QN

)PVTJOH4QFDJmDBUJPOTBOE1FSGPSNBODF%BUB

.PEFM

.BYJNVN%JNFOTJPOT

#10 Opaque

#10 Clear

#20 Opaque

12 1 ⁄

" x 5 1 ⁄

" (311 mm x 130 mm)

⁄

" x 5

⁄

" (321 mm x 133 mm)

22 3 ⁄

" x 5 1 ⁄

" (568 mm x 130 mm)

.BUFSJBMTPG$POTUSVDUJPO

Housing

Polypropylene (Opaque) or Styrene Acrylonitrile (Clear)

Cap

Button Assembly

Reinforced Polypropylene

300-series Stainless Steel, EPDM, and Polypropylene

O-Ring

Maximum Temperature

Maximum Pressure

#VOB/

125ºF (51.7ºC)

125 psi (8.62 bar)

CAUTION: Protect against freezing to prevent cracking of the filter and water leakage.

The 150001, 150002, 150067, 150068, 150071, 150072,

150435 and 150436 are Tested and Certiﬁed by NSF

International to NSF/ANSI Standard 42 for material and structural integrity requirements.

*OJUJBMå1 QTJ!'MPX3BUF HQN

1 psi @ 10 gpm (0.1 bar @ 38 Lpm)

*OEJBOB"WFOVFr10#PYr4IFCPZHBO8JTDPOTJO

$VTUPNFS4FSWJDFr'BYrTVQQPSUTQFDJBMJTU!QFOUFLàMUSBUJPODPN

*OUFSOBUJPOBMr'BYrJOUFSOBUJPOBM!QFOUFLàMUSBUJPODPN www.pentekfiltration.com Printed in USA MR06 310051

#20 Opaque

VIH

#10 Clear

VIH

VALVE-IN-HEAD FILTER HOUSINGS

• Ideal for a wide range of applications, including residential, commercial and industrial

• Available in 10" and 20" lengths

• Pressure-relief/bleed button on inlet side of cap

• Thick walls for increased strength

• Leak-proof sealing with top-seated Buna-N o-ring

• Available with clear or opaque sumps

Valve-in-head (VIH) filter housings incorporate the same rugged design and application features as our

Standard 3/4" NPT housings.

The internal valve-in-head allows both inlet and outlet ports to be simultaneously shut-off with a half turn of the handle. This eliminates the need for external shut-off valves.

Radial sealing o-rings and sealing surfaces are continuously cleaned each time the valve is used, ensuring leak-proof operation.

Valve-in-head filter housings are available in both 10" and 20" lengths, and will accommodate a wide range of 2

⁄

" to 2

⁄

" diameter cartridges. The polypropylene caps feature pressure-relief button on the inlet side to relieve pressure inside the housing when changing filter cartridges.

Opaque Valve-In-Head

Filter Housings

are molded from rugged reinforced polypropylene,

Opaque Valve-In-Head filter housings offer outstanding chemical compatibility and are ideal for use in a variety of low-flow applications.

These applications include undersink and countertop residential filtration, pre- and post-reverse osmosis filtration, recreational vehicle filtration, food service and humidifying systems.

Clear Valve-In-Head Filter Housings

offer on-site examination of flow, performance, and cartridge life.

Water Systems, Inc.

5301 Airport Rd.

Cle Elum, WA 98922

509 ‐ 674 ‐ 4000 F.

509 ‐ 674 ‐ 4002

Web: www.o3water.com

and www.cascadianwater.com

#10 Opaque

VIH

They are also ideal for a variety of applications.

Manufactured of clear, FDAcompliant Styrene-Acrylonitrile

(SAN), the sumps are annealed to relieve stress, adding clarity and strength.

VALVE-IN-HEAD

Filter Housings

'MPX3BUFoHQN -QN

Housing Specifications and Performance Data

Model Maximum Dimensions

#10 VIH

#10 VIH Clear

#20 VIH

⁄

" x 5

⁄

" (318 mm x 130 mm)

⁄

" x 5

⁄

" (327 mm x 133 mm)

⁄

" x 5

⁄

" (575 mm x 130 mm)

Materials of Construction

Housing

Polypropylene (Opaque) or Styrene Acrylonitrile (Clear)

Cap

Reinforced Polypropylene

Button Assembly

Valve Parts

O-Ring

Maximum Temperature

Maximum Pressure

300-series Stainless Steel, EPDM, and Polypropylene

Delrin

Buna-N

125ºF (51.7ºC)

125 psi (8.62 bar)

CAUTION: Protect against freezing to prevent cracking of the filter and water leakage.

The 150164 and 150172 are Tested and Certified by NSF

International to NSF/ANSI Standard 42 for material and structural integrity requirements.

Initial ∆P (psi) @ Flow Rate (gpm)

4 psi @ 8 gpm (0.3 bar @ 30 Lpm)

Water Systems, Inc.

5301 Airport Rd.

Cle Elum, WA 98922

509 ‐ 674 ‐ 4000 F.

509 ‐ 674 ‐ 4002

Web: www.o3water.com

and www.cascadianwater.com

502 Indiana Avenue • P.O. Box 1047 • Sheboygan, Wisconsin 53082-1047

Customer Service: 800.645.0267 • Fax: 888.203.7361 • [email protected]

International: 920.457.9435 • Fax: 920.457.2417 • [email protected]

www.pentekfiltration.com Printed in USA MR06 310052

3G STANDARD FILTER HOUSINGS

t*OUFHSBMCSBDLFUBOENPVOUJOHCPTTDBQWFSTJPOTBWBJMBCMF t"WBJMBCMFJOBOETVNQTJODMFBSBOEPQBRVF t#VUUSFTTUISFBETBOEVOJGPSNXBMMTGPSFBTJFSDBSUSJEHFDIBOHFBOEJNQSPWFETUSFOHUI t"DDFQUTQSPQSJFUBSZ4FBM¦4BGFEPVCMFP¦SJOHTFBMJOHDBSUSJEHFTBTXFMMBTTUBOEBSE%0&DBSUSJEHFT t0QUJPOBMQSFTTVSFSFMJFGCMFFECVUUPOBOEEJGGFSFOUJBMQSFTTVSFHBVHF t-FBLQSPPGTFBMJOHXJUIUPQ¦TFBUFEnPBUJOH#VOB¦/P¦SJOH

We took our time−tested industry standard and made it even better.

We started from the ground up, utilizing our 35 years of experience, to create the unique and innovative

3G design. This patented* design features integral brackets, 20" clear housings, and caps for differential pressure gauges. The 3G housings accept standard double open end

(DOE) and our Seal−Safe™ o−ring sealing cartridges. The Seal−Safe™ o−ring design offers enhanced cartridge sealing for critical cartridge applications.

3G Standard Filter Housings are manufactured from durable polypropylene or clear

Styrene

−

Acrylonitrile (SAN).

Reinforced polypropylene housings have excellent chemical resistance and are ideal for many residential, commercial and industrial applications. Clear sumps are manufactured from FDA compliant

Styrene

−

Acrylonitrile (SAN). They offer on

− site examination of the cartridge and have excellent chemical compatibility.

All are equipped with 3/4" NPT inlet and outlet ports. 3G Standard

Filter Housings are available in 10" and 20" lengths and will accommodate a wide range of 2 1 ⁄

" to 3 1 ⁄

" diameter cartridges.

* U.S. Patent No. D 455,194 S and D 456,486 S

3G SERIES

4UBOEBSE'JMUFS)PVTJOHT

(0.21)

(0.14)

(0.07)

(0.48)

(0.41)

(0.35)

(0.28)

Flow Rate – gpm (lpm)*

*Pressure drop and flow rate based on housing without cartridge.

)PVTJOH4QFDJmDBUJPOTBOE1FSGPSNBODF%BUB

.PEFM

.BYJNVN%JNFOTJPOT

3G #10 Blue or Clear MB

3G #20 Blue or Clear MB

3G #20 Blue or Clear IB/MM*

⁄

" x 5

⁄

" (324 mm x 137 mm)

13 1 ⁄

" x 5 3 ⁄

" (337 mm x 146 mm)

23" x 5 3 ⁄

" (597 mm x 137 mm)

23 1 ⁄

" x 5 3 ⁄

" (597 mm x 146 mm)

.BUFSJBMTPG$POTUSVDUJPO

Housing

Cap

Polypropylene (Opaque) or Styrene Acrylonitrile (Clear)

Reinforced Polypropylene

Button Assembly

O-Ring

300-series Stainless Steel, EPDM, and Polypropylene

Buna-N

Maximum Temperature

Maximum Pressure

125ºF (51.7ºC)

125 psi (8.62 bar)

CAUTION: Protect against freezing to prevent cracking of the filter and water leakage.

* Shown with differential gauge.

Gauges sold seperately.

*OJUJBMå1 QTJ!'MPX3BUF HQN

1 psi @ 10 gpm (0.07 bar @ 38 Lpm)

¥1FOUBJS'JMUSBUJPO*OD

*OEJBOB"WFOVFr10#PYr4IFCPZHBO8JTDPOTJO

$VTUPNFS4FSWJDFr'BYrTVQQPSUTQFDJBMJTU!QFOUFLàMUSBUJPODPN

*OUFSOBUJPOBMr'BYrJOUFSOBUJPOBM!QFOUFLàMUSBUJPODPN

XXXQFOUFLàMUSBUJPODPN 1SJOUFEJO64"'&

#20 Big Clear

#20 Big Blue ®

BIG BLUE

& BIG CLEAR FILTER HOUSINGS

t-BSHFDBQBDJUZIPVTJOHTVJUBCMFGPSIJHInPXBQQMJDBUJPOT tBOEMFOHUITBWBJMBCMFJOPQBRVFBOEDMFBS t1SFTTVSFSFMJFGCMFFEPOJOMFUTJEFPGDBQ t"DDFQUT ⁄ EJBNFUFSDBSUSJEHFT

#10 Big Blue ® #10 Big Clear

Big Blue ® Filter Housings

offer the versatility to meet all of your largecapacity filtration needs, including high-flow and heavy-sediment applications. The extra large housing allows for greater cartridge capacity, reducing the number of vessels required for high flow-rate applications. Sumps are constructed of durable reinforced polypropylene and are available in both 10" and

20" lengths.

The high-flow polypropylene

(HFPP) cap is available with 3/4",

1" or 1½" NPT inlet and outlet ports. The 1¼" internal port allows a greater volume of liquid to pass through the HFPP cap more rapidly.

Big Blue ® housings are compatible with a broad range of chemicals and are available with or without a pressure relief button. They accept a wide variety of 4½" diameter cartridges.

Big Clear Filter Housings

offer on-site examination of flow, performance, and cartridge life and are ideal for a variety of applications. The blue polypropylene caps are available with an optional pressure-relief button on the inlet side to relieve pressure inside the housing when changing filter cartridges.

BIG BLUE

IG CLEAR

'JMUFS)PVTJOHT

#JH$MFBS)'11

)'11

#JH#MVF #JH#MVF

The 150233, 150234, 150235, 150236, 150237,

150238, 150239, 150240, 150467, 150468, 150469, and 150470 Tested and Certiﬁed by NSF International to NSF/ANSI Standard 42 for material and structural integrity requirements.

NOTE: The Big Clear Series of housings are not NSF component listed.

'MPX3BUFoHQN -QN

)PVTJOH4QFDJmDBUJPOTBOE1FSGPSNBODF%BUB

.PEFM

.BYJNVN%JNFOTJPOT

#10 Big Blue ® –3/4"

#10 Big Blue ® –1"

#10 Big Blue ® –1 1 ⁄

#20 Big Blue

–3/4"

#20 Big Blue ® –1"

#20 Big Blue ® –1 1 ⁄

#10 Big Clear–1"*

#20 Big Clear–1"*

13 1 ⁄

" x 7 1 ⁄

" (333 mm x 184 mm)

⁄

" x 7

⁄

" (333 mm x 184 mm)

13 5 ⁄

" x 7 1 ⁄

" (346 mm x 184 mm)

23 3 ⁄

" x 7 1 ⁄

" (594 mm x 184 mm)

23 3 ⁄

" x 7 1 ⁄

" (594 mm x 184 mm)

23 7 ⁄

" x 7 1 ⁄

" (606 mm x 184 mm)

13½" x 7

⁄

" (343 mm x 181 mm)

23 ¾" x 7 1 ⁄

" (603 mm x 181 mm)

* Not Performance Tested or Certified by NSF.

.BUFSJBMTPG$POTUSVDUJPO

Housing

Cap

#*(#-6&

Polypropylene

Polypropylene (HFPP)

Button Assembly

O-Ring

Maximum Temperature

300-series Stainless Steel, EPDM, and Polypropylene

Buna-N

100ºF (37.8ºC)

Maximum Pressure

#10 Big Blue ®

–

100 psi (6.9 bar)

#20 Big Blue ®

–

90 psi (6.2 bar)

CAUTION: Protect against freezing to prevent cracking of the filter and water leakage.

*OJUJBMå1 QTJ!'MPX3BUF HQN

2 psi @ 15 gpm (0.1 bar @ 57 Lpm)

1 psi @ 15 gpm (0.1 bar @ 57 Lpm)

1 psi @ 20 gpm (0.1 bar @ 76 Lpm)

2 psi @ 15 gpm (0.1 bar @ 57 Lpm)

1 psi @ 15 gpm (0.1 bar @ 57 Lpm)

1 psi @ 20 gpm (0.1 bar @ 76 Lpm)

1 psi @ 15 gpm (0.1 bar @ 57 Lpm)

BIG CLEAR

Lexan (#10), Polycarbonate (#20)

Polypropylene (HFPP)

300-series Stainless Steel, EPDM, and Polypropylene

Buna-N

100ºF (37.8ºC)

#10 Big Clear – 100 psi (6.9 bar)

#20 Big Clear – 90 psi (6.2 bar)

¥1FOUBJS'JMUSBUJPO*OD

*OEJBOB"WFOVFr10#PYr4IFCPZHBO8JTDPOTJO

$VTUPNFS4FSWJDFr'BYrTVQQPSUTQFDJBMJTU!QFOUFLàMUSBUJPODPN

*OUFSOBUJPOBMr'BYrJOUFSOBUJPOBM!QFOUFLàMUSBUJPODPN

XXXQFOUFLàMUSBUJPODPN 1SJOUFEJO64".3

#20

Standard

HIGH TEMPERATURE FILTER HOUSINGS

t*EFBMGPSBXJEFSBOHFPGJOEVTUSJBMBQQMJDBUJPOT t"WBJMBCMFJOBOEMFOHUIT t&YDFMMFOUBMUFSOBUJWFUPTUBJOMFTTBOEDBSCPOIPVTJOHT t%VSBCMFHMBTTSFJOGPSDFEOZMPODPOTUSVDUJPO

Constructed of glass-reinforced nylon, High Temperature filter housings are an economical alternative to stainless and carbon steel housings.

These 1/2" NPT housings can withstand temperatures up to a maximum of 160ºF (71.1ºC) while 3/4" housings can withstand temperatures up to 165ºF (73.9ºC).

Excellent chemical compatibility makes High Temperature housings an ideal choice for a wide variety of industrial applications including those involving organic solvents, sea water, alcohol, petroleum and vegetable oils. They should not be used with ketones.

A #241 o-ring provides dependable sealing. Both 10" and 20" lengths are available to accommodate flow rates up to 20 gpm (76 Lpm).

#10

Slim Line ®

#10

Standard

HIGH TEMPERATURE

'JMUFS)PVTJOHT

4MJN-JOF

4UBOEBS

'MPX3BUFoHQN -QN

)PVTJOH4QFDJmDBUJPOTBOE1FSGPSNBODF%BUB

.PEFM

.BYJNVN%JNFOTJPOT

#10 Standard 3/4"

#20 Standard 3/4"

#10 Slim Line 1/2"

12 1 ⁄

" x 5 1 ⁄

" (308 mm x 130 mm)

⁄

" x 5

⁄

" (565 mm x 130 mm)

11 3 ⁄

" x 4 3 ⁄

" (298 mm x 111 mm)

.BUFSJBMTPG$POTUSVDUJPO

Housing

Cap

O-Ring

Maximum Temperature

Maximum Pressure

Glass-Reinforced Nylon

Slim Line ® Housings Viton ®

Standard Housings Silicone

1/2" Housing 160ºF (71.1ºC)

3/4" Housing 165ºF (73.9ºC)

125 psi (8.62 bar)

CAUTION: Protect against freezing to prevent cracking of the filter and water leakage.

*OJUJBMå1 QTJ!'MPX3BUF HQN

<1 psi @ 8 gpm (<0.1 bar @ 30 Lpm)

5 psi @ 8 gpm (<0.4 bar @ 30 Lpm)

/PSUI(MFO1BSL3PBEr.JMXBVLFF8*

$VTUPNFS4FSWJDFr'BYrTVQQPSUTQFDJBMJTU!QFOUFLàMUSBUJPODPN

*OUFSOBUJPOBMr'BYrJOUFSOBUJPOBM!QFOUFLàMUSBUJPODPN www.pentekfiltration.com FE09 310054

RO MEMBRANE HOUSING

t/4'MJTUFEDPNQPOFOU t.BOVGBDUVSFEGSPNBO'%"BQQSPWFEQPMZQSPQZMFOF t"DDPNNPEBUFTNPTUNFNCSBOFFMFNFOUT tBOHMFPVUMFU

The PENTEK ® RO Membrane

Housing is manufactured in the

U.S.A. from a high-quality, FDAapproved polypropylene.

This component is NSF listed and will accommodate most standard

12" membrane elements.

Both the ribbed cap and the housing are one-piece injection molded parts, requiring no solvents or glues to be used in the manufacturing process.

The ribbed cap incorporates acme square threads and two o-rings to ensure a leak-proof seal.

The RO Membrane Housings have a straight inlet and are equipped with (2) 90º outlets. The 90º outlets eliminate the need for additional elbows. All ports have standard 1/8”

NPT threads.

12" with 90º

Outlet

RO MEMBRANE

)PVTJOH

/15

.BUFSJBMTPG$POTUSVDUJPO

Housing

Reinforced Polypropylene

Finish

O-Ring

Reinforced Polypropylene

EPDM

Maximum Temperature

Maximum Pressure

' $

125 psi (8.62 bar)

CAUTION:

1SPUFDUBHBJOTUGSFF[JOHUPQSFWFOUDSBDLJOHPGUIFàMUFSBOEXBUFSMFBLBHF

¥1FOUBJS'JMUSBUJPO*OD

*OEJBOB"WFOVFr10#PYr4IFCPZHBO8JTDPOTJO

$VTUPNFS4FSWJDFr'BYrTVQQPSUTQFDJBMJTU!QFOUFLàMUSBUJPODPN

*OUFSOBUJPOBMr'BYrJOUFSOBUJPOBM!QFOUFLàMUSBUJPODPN

XXXQFOUFLàMUSBUJPODPN 1SJOUFEJO64".3

MPST-1.5 Multi-Purpose

Stainless Steel Filter Housing

The PENTEK MPST-1.5 multi-purpose stainless steel ﬁlter housing is designed to accept either a

4 1 ⁄

-inch x 20-inch double open end (DOE) cartridge or a PENTEK #420 bag filter. The housing comes standard as a cartridge filter housing, but the optional bag filter kit quickly converts it to a bag filter housing.

MPST-1.5

FEATURES

t 6TFTFJUIFS 1 ⁄

Y%0&DBSUSJEHFTPSCBHmMUFST t

⁄

TJEFJOMFUBOE 1

⁄

CPUUPNPVUMFU t 4JEFESBJOQMVHGPSFBTZDMFBOJOH t (BVHFQPSUTGPSFJUIFSDBSUSJEHFPSmMUFSCBHBQQMJDBUJPOT t 4OBQCBOEDMBNQGPSRVJDLDIBOHFPVUT t "EKVTUBCMFMFHTUBOEUPFBTFJOTUBMMBUJPO

The MPST-1.5 housing is constructed of 304 stainless steel and powder-coated for a professional ﬁnish. This versatile housing is supplied with 1 1 ⁄

-inch side inlet and bottom outlet ports, adjustable legs, drainage port and multiple gauge ports to easily adapt to any installation.

Applications include high temperature (250

F), high pressure (150 psi), and ﬂow rates up to 50 gpm.

Ideal for reduction of sediment and chlorine taste in whole house or small business applications, these housings can also be used in most water treatment, food processing and general ﬁltration applications.

BENEFITS

t 2VJDLMZDIBOHFTGSPNBDBSUSJEHFIPVTJOHUPBCBHIPVTJOH t 6TFTBOZ%0&

⁄

YDBSUSJEHFPSCBHmMUFS t *EFBMGPSIJHIUFNQFSBUVSFBOEIJHIQSFTTVSFBQQMJDBUJPOT t #PUUPNPVUMFUBOEBEKVTUBCMFMFHTUBOEBMMPXGPSnFYJCMF

BQQMJDBUJPOJOTUBMMBUJPOT t .VMUJQMFHBVHFQPSUTBMMPXUIFVTFPGEJGGFSFOUJBMQSFTTVSFHBVHFT

UPUBLFUIFHVFTTXPSLPVUPGXIFOUPDIBOHFUIFDBSUSJEHFPSCBH t 4OBQCBOEDMBNQNJOJNJ[FTEPXOUJNFGPSDIBOHFPVUTCZBMMPXJOH

RVJDLBDDFTTUPDBSUSJEHFPSCBHmMUFS

APPLICATIONS

t 4FEJNFOUSFEVDUJPOVTJOHmMUFSCBHTPSDBSUSJEHFT t $IMPSJOFUBTUFBOEPEPSSFEVDUJPO t 8IPMFIPVTFmMUSBUJPO t 3FTUBVSBOUTDBGFUFSJBTBOEGPPEQSPDFTTJOHPQFSBUJPOT t 4DIPPMTIPUFMTBOENPUFMT t -BVOESJFTBOEMBCPSBUPSJFT

MPST-1.5 Multi-Purpose Stainless Steel Filter Housing

Cartridge and Bag Options

Model Material

Recommended Sediment Cartridges:

DGD-2501-20

DGD-5005-20

Polypropylene

%(%

&$1##

4##

Polypropylene

Cellulose Polyester

Cellulose

Recommended Carbon Cartridges:

/$1## Pleated Carbon

3'$##

&1.##

Granular Carbon

$BSCPO#MPDL

&1##

$#$##

$3'$##

$BSCPO#MPDL

$IMPSBNJOF$BSCPO#MPDL

Recommended Specialty Cartridge:

0"$##

Oil Adsorbing

Micron

Rating

25 to 1

50 to 5

0.5

Model Material

Recommended Filter Bags:

#1)&

Polypropylene Felt

Polypro High Efﬁciency

Nylon Monoﬁlament

Micron

Rating

200

250

400

600

800

100

200

Housing Speciﬁcations and Performance Data

Model

Maximum

Flow Rate**

Dimensions Height x O.A. Dia*

MPST-1.5

50 gpm

-NJO

)

" x 6

⁄

NNYNN

NOTE: Bag ﬁlter conversion kit (243111) sold separately.

*NOTE: Will not accept model GAC 20BB, BBF1-20BB, WS-20BB or CRFC-20BB cartridges.

*Height does not include stand.

** Flow rate listed for housing without cartridge. Check cartridge speciﬁcations for cartridge ﬂow rates.

Materials of Construction

Housing 304 Stainless Steel

Finish

Sealing Gasket

Epoxy

#VOB/

NOTE: Maximum cartridge diameter 4 3 ⁄

-inches (12 mm)

WARNING: If pressure exceeds 150 psi (10.34 bar) at any time, a pressure regulator must be used. Do not use water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the system.

CAUTION: Protect against freezing to prevent cracking of the ﬁlter and water leakage.

NOTE: Not recommended for applications with TDS or chlorides >1000 ppm and/or pH <5.0. Use of this product in these conditions will void the limited warranty. Consult factory for product modiﬁcations for these conditions.

Pipe Size

(NPT)

⁄

(38.1 mm)

Maximum

Temperature

250 ºF

(121 ºC)

Maximum Pressure

150 psi

(10.34 bar)

Customize Your Housing

5BLFUIFHVFTTXPSLPVUPGXIFOUPDIBOHFUIFDBSUSJEHFPS

CBHCZBEEJOHPOFPGUXPEJGGFSFOUTUZMFHBVHFT

Needle differential pressure gauge

Needle points to international standard colors to determine when cartridge should be changed.

Green (clean) 0-6 psid;

Yellow (change) 6-9 psid;

Red (dirty) 9-12 psid.

143549*

143550*

* Gauges sold separately

Color change differential pressure gauge

Green and red colors indicate when cartridge should be changed.

Green (clean) 0-7 psid;

Red (change) 7-10 psid.

*OEJBOB"WFOVFt10#PY

4IFCPZHBO8JTDPOTJO

1IPOFt

'BYt www.pentekﬁltration.com

ST SERIES STAINLESS STEEL FILTER HOUSINGS

t)FBWZEVUZVOJUTGPSTNBMMFSmMUSBUJPOTZTUFNTBOEQPJOUPGVTFBQQMJDBUJPOT t#SVTIFETUBJOMFTTTUFFMTVNQXJUIBDBTUCSBTTOJDLFMQMBUFEIFBE t*EFBMGPSIJHIQSFTTVSFIPUXBUFSBQQMJDBUJPOT t"DDFQUTDPNQMFUFSBOHFPGTUBOEBSEEPVCMFPQFOFOE %0&DBSUSJEHFT

ST Series stainless steel filter housings effectively provide heavy-duty filtration for smaller filtration systems and point-of-use applications. Supplying flow rates of up to 20 gpm (76 Lpm), at a maximum water temperature of

300ºF (149ºC), ST Series housings are ideal for hot water and highpressure applications not suited for plastic housings.

The brushed 304 stainless steel sumps are available with either a pipe plug or pet-cock in the bottom for draining. Heads are manufactured from nickel-plated cast-brass.

ST Series housings are easy to install and maintain. They are compatible with a complete range of filter cartridges, adding to their versatility.

ST-1

ST-3

ST-2

ST SERIES

4UBJOMFTT4UFFM'JMUFS)PVTJOHT

)PVTJOH4QFDJmDBUJPOTBOE1FSGPSNBODF%BUB

.PEFM

.BYJNVN%JNFOTJPOT 'MPX3BUF HQN .BYJNVN1SFTTVSF

ST-1

ST-2

ST-3

⁄

" x 4

⁄

" x 4

⁄

" (327 mm x 105 mm)

" (578 mm x 105 mm)

" (822 mm x 105 mm) r.BYJNVNDBSUSJEHFEJBNFUFS NN r8JMMOPUBDDFQU("$$$$("$54("$841$'PS1$$4FSJFT$BSUSJEHFT

10 gpm (38 Lpm)

15 gpm (57 Lpm)

20 gpm (76 Lpm)

250 psi (17.2 bar)

.BUFSJBMTPG$POTUSVDUJPO

Housing

Head

#SVTIFE4UBJOMFTT4UFFM

#SBTT/JDLFM1MBUFE

Maximum Temperature

Pipe Size

300ºF (149ºC)

/15

Sealing Gaskets

#VOB/$FMMVMPTF'JCFS

WARNING: For drinking water applications, do not use with water that microbiologically unsafe or of unknown quality without adequate disinfection before or after the system.

CAUTION: Protect against freezing to prevent cracking of the filter and water leakage.

¥1FOUBJS'JMUSBUJPO*OD

*OEJBOB"WFOVFr10#PYr4IFCPZHBO8JTDPOTJO

$VTUPNFS4FSWJDFr'BYrTVQQPSUTQFDJBMJTU!QFOUFLàMUSBUJPODPN

*OUFSOBUJPOBMr'BYrJOUFSOBUJPOBM!QFOUFLàMUSBUJPODPN

XXXQFOUFLàMUSBUJPODPN 1SJOUFEJO64".3

ST-BC-16

ST-BC SerieS STainleSS STeel

FilTer HouSingS

• Heavy duty units for large scale commercial/industrial applications

• Brushed 304 stainless steel construction with a gray-silver epoxy finish

• ideal for high-temperature applications

• accepts complete range of standard double open end (Doe) cartridges

ST-BC Series housings are compatible with a complete range of filter cartridges, adding to their versatility.

ST-BC Series stainless steel filter housings offer a variety of solutions for your large-scale, heavy-duty filtration needs. Simple to install and maintain, these housings are ideal for schools, restaurants, farms, institutions and industrial use.

Holding from 4 to 20 cartridges,

ST-BC Series housings provide flow rates from 28 – 125 gpm (106-473

Lpm).

Housings are constructed of 304 stainless steel with a gray-silver epoxy finish. They include drains on both the “clean” and “dirty” sides of the sump.

ST-BC-12

ST-BC-4

ST-BC-20

ST-BC-8

ST-BC SerieS

Stainless Steel Filter Housings

Housing Specifications and Performance Data

Model

ST-BC-4

ST-BC-8

recommended*

Flow rates

28 gpm (106 Lpm)

56 gpm (212 Lpm)

⁄

ST-BC-20 125 gpm (473 Lpm) 49

⁄

Dimensions

Height x o.a. Dia.

" x 10" (489 mm x 254 mm)

29" x 10" (737 mm x 254 mm)

ST-BC-12 84 gpm (318 Lpm) 39

⁄

" x 10" (1010 mm x 254 mm)

ST-BC-16 110 gpm (416 Lpm) 49

⁄

" x 10" (1264 mm x 254 mm)

Max. no.**

Cartridges

4 x 1

4 x 2

4 x 3

4 x 4

5 x 4

• Will not accept GAC, CC, CGAC, TSGAC, WS, PCF or PCC Series Cartridges.

Max. Cart.

Diameter

3" (76 mm)

⁄

" (64 mm)

Max. Cartridge length

Pipe Size

(nPT)

⁄

" or 10" (248 mm or 254 mm) 2" (50.8 mm)

⁄

" or 10" (248 mm or 254 mm) 2" (50.8 mm)

⁄

" or 10" (248 mm or 254 mm) 2" (50.8 mm)

⁄

" or 10" (248 mm or 254 mm) 2" (50.8 mm)

⁄

" or 10" (248 mm or 254 mm) 2" (50.8 mm)

Materials of Construction

Housing

Finish

Maximum Temperature

Maximum Pressure

Brushed 304 Stainless Steel

Epoxy

300ºF (149ºC)

125 psi (8.62 bar)

Pipe Size

Sealing Gasket

2" NPT

Buna-N

* Based on sediment removal with a 25-micron filter cartridge and 1 PSIG initial clean pressure drop.

** Number of cartridges refers to the number of 9

⁄

" (248 mm) or 10" (254 mm) cartridges which are configured around the housing times the number of cartridges that may be stacked. Example 4 x 2 means that 9

⁄

" (248 mm) cartridges are configured four around and two high.

NOTE:

Maximum cartridge diameter 3" (76 mm).

WARNING:

If pressure exceeds 125 psi (8.62 bar) at any time, a pressure regulator must be used. Do not use water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the system.

CAUTION:

Protect against freezing to prevent cracking of the filter and water leakage.

NOTE:

Not recommended for applications with TDS or chlorides >1000 ppm and/or pH <5.0. Use of this product in these conditions will void the limited warranty. Consult factory for product modifications for these conditions.

502 Indiana Avenue • P.O. Box 1047 • Sheboygan, Wisconsin 53082-1047

Customer Service: 800.645.0267 • Fax: 888.203.7361 • [email protected]

International: 920.457.9435 • Fax: 920.457.2417 • [email protected]

www.pentekfiltration.com Printed in USA MR06 310057

BAG VESSEL FILTER ASSEMBLIES

t-JHIUXFJHIUDPSSPTJPOSFTJTUBOUQPMZQSPQZMFOFDPOTUSVDUJPOHJWFTZPVTUSFOHUIXJUIPVUXFJHIU t$IPJDFPGPSIPVTJOHT t"WBJMBCMFJOBOE

⁄

/15TJ[FT t$PNFDPNQMFUFXJUIHBVHFXSFODIBOEESBJOWBMWF t-JHIUFOPVHIUPCFQPSUBCMF t&DPOPNJDBMMZQSJDFE

PENTEK's standard bag vessel assemblies keep your system on stream longer by reducing bag filter change time. They are made of lightweight corrosion resistant polypropylene to give you all the strength you need without the weight.

Install as a duplex system for totally uninterrupted flow rates.

All PBH Series vessels come complete with gauge, wrench and

3/8" drain valve. The single large

Acme thread closure ensures quick opening and positive sealing.

Filter bags are available in polypropylene felt, absolute-rated high-efficiency polypropylene and nylon monofilament mesh–ideal for filtering and straining applications from 1 to 800 microns.

Molded from rugged reinforced polypropylene, Bag filter housings offer outstanding chemical compatibility and are ideal for use in a variety of low-flow applications. These applications include residential prefiltration, food service along with commercial and industrial applications for water filtration and chemical filtration.

They are equipped with a black, reinforced polypropylene cap.

*Bag vessel stand sold separately.

PBH-410

(Shown with bag vessel stand)*

PBH-420

BAG VESSEL

'JMUFS"TTFNCMJFT

1#)o

'MPX3BUFoHQN -QN

)PVTJOH4QFDJmDBUJPOTBOE1FSGPSNBODF%BUB

.PEFM

.BYJNVN%JNFOTJPOT *OJUJBMå1 QTJ!'MPX3BUF HQN

PBH-410-1 (1" NPT)

PBH-410-1.5 (1

⁄

" NPT)

PBH-420-1 (1" NPT)

PBH-420-1 (1

⁄

" NPT)

23 3

⁄

" x 7

⁄

" x 7 1

" x 7

⁄

" (333 mm x 184 mm)

" (346 mm x 184 mm)

⁄

" (594 mm x 184 mm)

" (606 mm x 184 mm)

1 psi @ 15 gpm (0.07 bar @ 57 Lpm)

1 psi @ 15 gpm (0.07 bar @ 57 Lpm) r1#)BDDFQUTBTUBOEBSEY 1

⁄

" (102 mm x 210 mm) bag. Dimensions allow for 1" (25 mm) overlap on basket.

r1#)BDDFQUTBTUBOEBSEY 1 ⁄

" (102 mm x 470 mm) bag. Dimensions allow for 1" (25 mm) overlap on basket.

.BYJNVN1SFTTVSF

100 psi (6.9 bar)

90 psi (6.2 bar)

.BUFSJBMTPG$POTUSVDUJPO

Housing

Cap

Gauge

Polypropylene

Bismuth Brass (lead-free)

Vent Plug

Drain Plug

Ball Valve

Basket

O-Ring and Gaskets

Polypropylene

High Density Polypropylene

PVC/Buna-N Seals

Polypropylene

Buna-N

Maximum Temperature

100ºF (37.8ºC)

NOTE: Many standard bags with rings may be used in these vessels. Refer to PENTEK's bag filter specifications sheet for 1 to 200 micron quick-install bags.

*OEJBOB"WFOVFr10#PYr4IFCPZHBO8JTDPOTJO

$VTUPNFS4FSWJDFr'BYrTVQQPSUTQFDJBMJTU!QFOUFLàMUSBUJPODPN

*OUFSOBUJPOBMr'BYrJOUFSOBUJPOBM!QFOUFLàMUSBUJPODPN www.pentekfiltration.com Printed in USA MR06 310055

TradiTional in-line FilTer SerieS

• Provide bad taste & odor and chlorine taste & odor reduction

• injection molded and pressure rated to 125 psi

• all in-line filters include a pre- and post-filter

PENTEK Traditional In-Line filters feature coconut shell, granular activated carbon, and are designed to reduce unwanted taste, odor and chlorine taste and odor.

The TS-101L contains a combination of GAC and polyphosphate crystals to inhibit lime/scale build-up.

All Traditional In-Line filters include a durable, injection molded polypropylene body and cap, pre- and post-filter. They are pressure rated to 125 psi. and come standard with 1/4" NPT connections.

Traditional In-Line filters are an ideal choice for post-RO, undersink, ice-maker and food service applications.

Contact factory regarding availability of other sizes and media.

IC-101L

TS-101L

TradiTional in-line SerieS

disposable in-line Filters

The IC-101L and TS-101L are Tested and Certified by NSF

International.

'MPX3BUFoHQN -QN

Specifications and Performance data

Model Media

IC-101L

TS-101L

Coconut Shell GAC (17 cu. in.)

Phosphate/GAC (16 cu. in.)

Maximum dimensions

2" x 10

⁄

" (51 mm x 270 mm)

2" x 10

⁄

" (51 mm x 270 mm)

estimated life

2500 gallons (9460L)

1700 gallons (6450L)

Flow rate

0.75 gpm (2.8 Lpm)

Materials of Construction

Body

Polypropylene

Cap

Polypropylene

Pre-Filter and Post-Filter

Carbon

Maximum Temperature

Operating Pressure

Polypropylene

Coconut Shell GAC

100ºF (37.8ºC)

125 psi (8.62 bar)

WARNING:

For drinking water applications, do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the system.

NOTE:

Cartridges will contain a very small amount of fines (very fine powder) and new cartridges, after installation, should be flushed with sufficient water to remove all traces of fines from your water system before use. Each time you use your filtered water tap for drinking or cooking purposes, it is recommended that you run (flush) the tap for at least 10 seconds prior to using the water. This is particularly important if the water tap has not been used daily.

CAUTION:

Protect against freezing to prevent cracking of the filter and water leakage.

502 Indiana Avenue • P.O. Box 1047 • Sheboygan, Wisconsin 53082-1047

Customer Service: 800.645.0267 • Fax: 888.203.7361 • [email protected]

International: 920.457.9435 • Fax: 920.457.2417 • [email protected]

www.pentekfiltration.com Printed in USA MR06 310093

QUICK-CHANGE FILTRATION SYSTEMS

• Easy to install, easy filter change

• Unique cover for single unit for a more appealing look

• Reversible metal brackets for 1, 2 or 3 cartridges

†

• 1/4-inch or 3/8-inch John Guest ® push-fit connections available

• 1/4-inch compression connections available for flex hose connections

• Seven cartridge models to choose from to meet specific application needs

PENTEK

Quick Change Filtration

Systems are designed for easy installation and cartridge change.

1/4-inch or 3/8-inch push fittings, as well as 1/4-inch compression fittings, on the inlet and outlet sides of the filter head allow effortless installation. Many single systems are

NSF Certified.

The cartridge filter is easily changed with a quarter-turn of the filter.

Water is automatically shut off during the change of the filter through the auto shut-off feature built into the filter head. This feature eliminates the need for additional shut-off valves to and from the filter system.

The PENTEK quick-change filter system offers several cartridge options to meet the demands of varying water conditions. The granular activated carbon cartridge offers extended chlorine taste and odor performance with low pressure drop.* The EP carbon block filter offers superior chlorine taste and odor performance with 5 micron sediment reduction.* The CBR carbon block cartridge has enhanced performance capabilities for chlorine taste & odor, cyst, lead, atrazine and lindane reduction.

The new cartridges include carbon/ phosphate cartridge, chloramine reduction cartridge, sediment only

WFS

$PNJOH

4PPO

† The Twin and Triple systems are not performance tested or certified by NSF.

cartridge, a high performance 1micron carbon block cartridge, and the soon to be released membrane filter cartridge for bacteria and virus reduction.*

PENTEK's quick-change filter system applications include:

• under-sink drinking water

• refrigerator/icemaker

• pre/post RO membrane

• vending machine

• ice machine

• coffee machine

• other OEM applications

* Not performance tested or certified by NSF.

*Not Performance Tested or Certified by NSF.

Water Systems, Inc.

5301 Airport Rd.

Cle Elum, WA 98922

509 ‐ 674 ‐ 4000 F.

509 ‐ 674 ‐ 4002

Web: www.o3water.com

and www.cascadianwater.com

QUICK-CHANGE

Filtration Systems

* Shown with optional designer cover

The Twin and Triple systems are Not Performance Tested or Certified by NSF.

Model

QC10-CBR

QC10-EP

Cartridge

Color

White

Claims

chlorine taste & odor, sediment, lead, atrazine, lindane, cyst and turbidity chlorine taste & odor

Filter Life

500 gallons

(1890 L)

1,500 gallons

(5670 L)

QC10-GAC

QC10-TSGAC

Blue

Blue chlorine taste & odor chlorine taste & odor with phosphate crystals sediment

2,500 gallons

1,700 gallons

(9460 L)

(6435 L)

QC10-SED1 White –

QC10-CGAC

QC10-CB1

†

Blue

White chloramine taste & odor and chlorine taste & odor † chlorine taste & odor and sediment

500 gal. (1890 L) chloramine*

10,000 gal. (37850 L) chlorine*

10,000 gallons

*Filter life based on chlorine reduction as tested by Pentair Filtration, Inc.

†Not Performance Tested or Certified by NSF.

(37850 L)

Flow

Rate

0.5 gpm

(1.9 L/min)

0.5 gpm

(1.9 L/min)

0.75 gpm

(2.8 L/min)

0.75 gpm

(2.8 L/min)

0.6 gpm

(2.3 L/min)

0.6 gpm

(2.3 L/min)

0.6 gpm

(2.3 L/min)

Micron

Rating

0.5

–

†

1/4-inch

Threaded

1/4-inch

Push fit

3/8-inch

Push fit

•

–

•

The QC10-CBR is Tested and Certified by NSF/ANSI to Standard 42 for the reduction of Chlorine Taste & Odor and Particulate Class I. Standard 53 Atrazine, Cyst, Lead,

Lindane and Turbidity.

The QC10-SED1 is Tested and Certified by NSF International to NSF/ANSI Standard

42 for the aesthetic reduction of Particulate Class 1.

QC10-EP is Tested and Certified by NSF/ANSI to Standard 42 for the reduction of

Chlorine Taste & Odor.

The QC10-CB1 is Tested and Certified by NSF International to NSF/ANSI Standard

42 for the aesthetic reduction of Chlorine Taste & Odor and Particulate Class 1.

QC10-GAC and QC10-TSGAC is Tested and Certified by NSF/ANSI to Standard 42 for the reduction of Chlorine Taste & Odor.

WARNING:

Do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the system.

CAUTION: Protect against freezing to prevent cracking of the filter housing and water leakage.

Note: Cartridge will contain a very small amount of carbon fines (a very fine black powder). After installation and before using the water follow the instructions for flushing the cartridge to remove fines.

U.S. Patent Numbers 5,976,432 and 5,823,668

Water Systems, Inc.

5301 Airport Rd.

Cle Elum, WA 98922

509

Web:

‐ 674 ‐ 4000 F.

509 ‐ 674 www.o3water.com

‐ and

4002 www.pentekfiltration.com

www.cascadianwater.com

Printed in USA AU06 310125

RO-3500

UNDER-SINK DRINKING WATER SYSTEMS

• US-1000 & US-1500 Chemical/Lead Systems

• AS-301E Arsenic Reduction System*

• RO-3000 & RO-3500 Reverse Osmosis Systems

US-1500

AS-301E

PENTEK

offers five systems suitable for under-sink, point-ofuse installation. These units offer a variety of contaminant reduction capabilities.

The

US-1000

and

US-1500

Chemical/Lead Systems are NSF certified to reduce 43 different

VOCs, lead, cysts, mercury, asbestos and chlorine taste & odor. Both systems come complete with cartridges, a long reach faucet, and installation hardware. The US-1500 features an electronic monitor for filter replacement. The US-1000 features MTBE reduction.

The

AS-301E

Arsenic Reduction

System reduces Arsenic III & V and chlorine taste & odor, a mechanical meter and comes complete with full hardware kit and faucet.*

The

RO-3000

and

RO-3500

Reverse Osmosis systems offer the finest level of water filtration available—filtering particles as small as 1/1000 of a micron. These systems are NSF certified to reduce salts, dissolved minerals and bad taste & odor and are designed for chlorinated or non-chlorinated water. The RO-3000 and RO-3500 each produce up to 7.6 gallons of top quality water per day, depending on your operating conditions. The

RO-3500 features an electronic water quality monitor to indicate when to change the RO membrane.

Both systems come complete with cartridges, a long reach faucet, and installation hardware.

* Not performance tested or certified by NSF.

UNDERSINK

DRINKING WATER

SYSTEMS

System Specifications

Model Claims

US-1000

US-1500

AS-301E

RO-3000

†

Bad Taste & Odor, Chlorine Taste & Odor, Sediment,

Asbestos, Cyst, Lead, Mercury, MTBE, Turbidity, VOC

Bad Taste & Odor, Chlorine Taste & Odor, Sediment,

Asbestos, Cyst, Lead, Mercury, Turbidity, VOC

Bad Taste & Odor, Chlorine Taste & Odor, Sediment,

Arsenic III, Arsenic V †

Bad Taste & Odor, Chlorine Taste & Odor, Copper, Cyst,

Fluoride, Lead, Selenium, Dissolved Minerals & Salts,

Turbidity

RO-3500

Chlorine Taste & Odor, Pentavalent Arsenic, Barium,

Cadmium, Copper, Hexavalent & Trivalent Chromium,

Cyst, Fluoride, Lead, Nitrate/Nitrite, Radium 226/228,

Selenium, Dissolved Minerals & Salts, Turbidity

†Based on manufacturer's internal testing.

Maximum Dimensions

15" x 11" x 6.5"

(381mm x 279mm x 165mm)

15" x 11" x 6.5"

(381mm x 279mm x 165mm)

⁄

" x 5

⁄

" x 14"

(394mm x 133mm x 356mm)

⁄

" x 4

⁄

" x 12

⁄

" system

(349mm x 120mm x 324mm)

⁄

" x 11

⁄

" x 16

⁄

" tank

(286mm x 286mm x 425mm)

⁄

" x 4

⁄

" x 12

⁄

" system

(349mm x 120mm x 324mm)

⁄

" x 11

⁄

" x 16

⁄

" tank

(286mm x 286mm x 425mm)

Replacement Parts

Model

P-250

P-250A

AS-CK

ROM-230T

ROM-230TN

ROR

SW-2

SW-5

FT-20LR

Description

Cartridge Set

Thin Film Membrane

RO Replacement Cartridge Set

Spanner Wrench

Faucet

Auto Shut-Off Valve

Part Number

155584-43

155832-43

255401-43

155854-01

155855-19

155923-43

150295

150424

244439

144653

Pressure

Range

10-125 psi

30-125 psi

40-100 psi

Filter Life/

Daily Capacity

500 gallons

1000 gallons

†

7.6 gallons/day

Fits

US-1500

US-1000

AS-301E

RO-3000

RO-3500

RO-3000, RO-3500

AS-301E

US-1000, US-1500, RO-3000, RO-3500

US-1000, US-1500

RO-3000, RO-3500

The US-1000 is Tested and Certified by NSF/ANSI to Standard 42 for the reduction of Chlorine Taste & Odor and Particulate Class I. Standard 53 Asbestos, Cyst, Lead,

Mercury, MTBE, Turbidity and VOC.

The US-1500 is Tested and Certified by NSF/ANSI to Standard 42 for the reduction of Chlorine Taste & Odor and Particulate Class I. Standard 53 Asbestos, Cyst, Lead,

Mercury, Turbidity and VOC.

The RO-3000 is Tested and Certified by NSF/ANSI to Standard 58 for the reduction of Copper, Cyst, Fluoride, Lead, Selenium, TDS and Turbidity.

The RO-3500 is Tested and Certified by NSF/ANSI to Standard 58 for the reduction of Pentavalent Arsenic, Barium, Cadmium, Copper, Hexavalent & Trivalent

Chromium, Cyst, Fluoride, Lead, Nitrate/Nitrite, Radium 226/228, Selenium, TDS and Turbidity.

502 Indiana Avenue • P.O. Box 1047 • Sheboygan, Wisconsin 53082-1047

Customer Service: 800.645.0267 • Fax: 888.203.7361 • [email protected]

International: 920.457.9435 • Fax: 920.457.2417 • [email protected]

www.pentekfiltration.com Printed in USA AU06 310127

UVBB-120-1

UV-110-2

UV SerieS UltraViolet SyStemS

• High-intensity UV output for supplemental microbiological control in drinking or process water

• Positive alternative to environmentally harmful chemicals

• available in three different sizes and two different voltages

UV-110-1

UVS-110-1

The UVS-110, UV-110, UV-120 and UVBB Ultraviolet Systems are effective at protecting potable drinking water sources from occasional intrusion of microbiological contamination.

This positive alternative to environmentally harmful chemicals uses ultraviolet light to control microbes. A germicidal dose of ultraviolet light (16,000 microwattsec per square centimeter) at a wavelength of 254 nanometers, disrupts the microbes reproductive process.

All UV Series systems are constructed with a durable polypropylene housing; a quartz sleeve to protect the lamp and provide maximum UV transmittance; a UL-listed, voltage regulated control module, mounting bracket and hardware.

UV-120 and UVBB models are equipped with a stainless steel insert sleeve to provide increased durability and maximize microbe reduction.

UVS-110 and UV-110 systems are equipped with a CBU-10 carbon block cartridge to provide protection against Cryptosporidium and Giardia cysts and assuring maximum UV transmittance through the water by reducing turbidity.

UV Series ultraviolet systems are available in two sizes: 120 volt, 60 hertz; and 220/240 volt, 50 hertz.

System flow rate range from 1-15 gpm (3.8 - 57 L/min).

UV SerieS

Ultraviolet Systems

Minimum Dose:*

16 mJ/cm 2

(16,000 microwatt-sec per cm 2 )

Models UVS-110-1, UVS-110-2, UV-110-1 and UV-110-2 incorporate a carbon block cartridge (CBU-10) that surrounds the quartz tube. This cartridge provides prefiltration that assures maximum transmittance of UV light through the water and reduction of cysts such as Cryptosporidium and Giardia.

NOTE:

Carbon block prefilters or other fine filtration can be plumbed in separately to provide this function for models UV-120 and UVBB-120.

*Determined by:

LAMP INTENSITY (microwatts) X TIME OF EXPOSURE IN REACTOR CHAMBER (sec)

÷ SURFACE AREA OF REACTOR CHAMBER (cm

) = microwatt • sec/cm

= mJ/cm

/1000

X-Ray Vacuum UV

Germicidal

Short Wave

UV-C

Middle Wave

UV-B

Sun Tanning

Long Wave

UV-A

Visible Light

100 200 254

PENTEK UV

300 400 800

Nanometers

System Specifications and Performance Data model

UVS-110-2*

†

UV-110-1*

UV-110-2*

UV-120-1

UV-120-2

UVBB-120-1

UVBB-120-2

Dimensions

⁄

" x 15

⁄

" (140 mm x 394 mm)

⁄

" x 15

⁄

" (140 mm x 394 mm)

⁄

" x 15

⁄

" (140 mm x 394 mm)

⁄

" x 25

⁄

" (140 mm x 648 mm)

⁄

" x 25

⁄

" (140 mm x 648 mm)

7" x 29" (178 mm x 737 mm)

Voltage

220

120

220

120

220

120

220

Hertz

recommended Flow rates

1 gpm (3.8 Lpm)

2 gpm (7.6 Lpm)

8 gpm (30.3 Lpm)

15 gpm (56.8 Lpm)

* Supplied with a carbon block filter cartridge which reduces sediment, bad taste and odor, Cryptosporidium and Giardia cysts.

† For export sale only.

materials of Construction

Housing

Cap

Polypropylene

UV Sleeve

O-Rings

Temperature Rating

Reaction Chamber

Quartz

Buna-N

40–100ºF (4.4–37.8ºC)

Stainless Steel (20" models only)

WARNING:

Do not use where the water is microbiologically unsafe or with water of unknown quality without adequate disinfection before or after the system.

EPA Est. No: 039861-WI-001

maximum operating

Pressure

65 psi (4.5 bar)

502 Indiana Avenue • P.O. Box 1047 • Sheboygan, Wisconsin 53082-1047

Customer Service: 800.645.0267 • Fax: 888.203.7361 • [email protected]

International: 920.457-9435 • Fax: 920.457.2417 • [email protected]

www.pentekfiltration.com Printed in USA MR06 310091

FRESHPOINT™ ULTRAFILTRATION SYSTEM

Designed for cyst reduction, turbidity, and ﬁne sediment ﬁltration applications t

> 98% reduction of 0.025 micron

(25 nanometer) particles* t

> 99.99% (> 4 Log) reduction of

0.065 micron (65 nanometer) particles*

The PENTEK ® FreshPoint™

Ultrafiltration System provides complete point-of-entry (POE) filtration proven to reduce turbidity, particulates and cysts for safer, cleaner water at every tap. The system employs hollow-fiber

Ultrafiltration membrane technology to filter impurities as small as 0.025 microns.

To maximize membrane capacity and service life, a metered flushing cycle is controlled using an advanced controller and high-performance turbine meter. The self-cleaning forward and back-flush cycles are initiated when the programmed capacity of the membrane is reached. During the backwash, flow is reversed and particles are ejected from the pores of the membrane and flushed to drain. In the forward-

Forward-flush and back-flush cleaning cycles provide extended filter life in a wide range of applications t

Proprietary hollow-ﬁber ultraﬁltration membrane t

Professional-grade housing, controller and ﬂush valve

flush cycle, service water passes through the capillaries at a high speed, scouring particles from the membrane surface and rinsing them from the system. Since power is only required to flush the system, outages and interruptions will not jeopardize the integrity of membrane or its ability to provide safer, cleaner water.

The advanced electronic controller provides a programmable day override which allows the unit to flush every day with fresh water when the system is not in use.

Critical system diagnostics, including totalized flow, instantaneous flow rate, and previous day’s water usage, are available to optimize flushing cycles and monitor performance.

Metered self-cleaning cycle ﬂushes only when needed t

Day override feature ﬂushes module daily with fresh water when system is not in use t

Peak ﬂow rates up to 10 gpm (2271 L/h)

The new high performance industrial stainless steel housing is pressure rated to 300 PSI. The new housing includes one piece endcaps with robust o-ring seals, all plumbing connection points, as well as, locking bars which allow for easier installation and service while minimizing the potential for leakage.

In addition, test ports/pressure taps are built into the endcaps to allow for easier integrity testing to ensure your membrane fibers are intact.

The system can be applied to solve “known” water problems including high turbidity, suspended solids, and certain microbiological contaminants. It can also serve as a flushable prefilter to extend the life of media filters downstream.

This product is not certiﬁed as a microbiological puriﬁer and should not be applied as a stand-alone disinfection solution for microbiologically unsafe water.

* Performance based on MS-2 (25 nm) and PRD-1 (65 nm) virus particle tests. Data available upon request.

Safe, Clean Water

™

ULTRAFILTRATION

FreshPoint™

Advantages of FreshPoint™ Filter Technology

t3FEVDFTUVSCJEJUZDZTUTBOEPUIFSQBSUJDMFT

EPXOUPNJDSPOJOTJ[F t.VMUJCPSFNFNCSBOFTUSVDUVSFDPNCJOFT

TFWFOTJOHMFDBQJMMBSJFTJOUPPOFSFTJTUBOU

TUSVDUVSFUPNBYJNJ[FNFNCSBOFJOUFHSJUZ

WJSUVBMMZFMJNJOBUJOHUIFQPUFOUJBMGPSmCFS

CSFBLBHF t3FRVJSFTPOMZOPSNBMMJOFQSFTTVSFUPPQFSBUF t1SPUFDUTEVSJOHQPXFSPVUBHFT

PSJOUFSNJUUFOUQPXFS t3FUBJOTOBUVSBMNJOFSBMDPOUFOUPGUIFXBUFS t)JHITVSGBDFBSFBBOEUPMFSBODFUPQMVHHJOH t-PXQSFTTVSFESPQ)JHInPXSBUFT

ET Electronic Metered Controller

t.FUFSFETFMGDMFBOJOHDZDMFnVTIFTPOMZXIFO

OFFEFEVTJOHMFTTUIBOHBMMPOTQFSnVTIDZDMF t%BZPWFSSJEFGFBUVSFnVTIFTNPEVMFEBJMZXJUI

GSFTIXBUFSXIFOTZTUFNJTOPUJOVTF t4VJUBCMFGPSJOEPPSPSPVUEPPSBQQMJDBUJPOT t"MMQBSBNFUFSTBSFBEKVTUFEWJBUJNFS

QSPHSBNNJOHBOEDBOCFNPEJmFEBUBOZUJNF t#SJHIUEJHJU7'%EJTQMBZXJUIVTFSQBOFM

VUJMJ[JOH-&%TUBUVTQSPHSBNNJOHJOEJDBUPST t"SFHFOFSBUJPOMPDLPVUJOQVUJTBWBJMBCMF t%JBHOPTUJDEJTQMBZGPS5PUBMJ[FE'MPX

*OTUBOUBOFPVT'MPX3BUF%BZT4JODF

-BTU'MVTI1SJPS4FSWJDF7PMVNF

1SFWJPVT%BZT8BUFS6TBHF t1SPHSBNNBCMFBVYJMJBSZSFMBZ t7CBUUFSZCBDLVQNBJOUBJOTUJNFPGEBZ

System Speciﬁcations and Performance Data

Membrane

Material

Pore Size

Polyethersulfone, modified (PESM)

0.025 micron (nominal)

0.065 micron (absolute)

Molecular Weight Cut Off

(MWCO)

Active Membrane Surface

Service Flow Rate @

15 psi drop

100-150 kD

51 sq. ft.

6.23 gpm to 10 gpm

(1,416 L/h to 2,271 L/H

Controller

Electrical Rating

Forward Flush Cycle

Metered Volume

Meter Accuracy

50/60 Hz

1-99 minutes

1-9999 gallons

1-50 gpm +/- 5%

System

Inlet/Outlet 3/4-inch NPT

Pentair Water Solutions for Complete POE Treatment

Pressurized

Retention Tank

FreshPoint

Ultraﬁltration

System

Whole House

Carbon Filter

Softener Control

Valve

Whole House

Sediment Filter

NOTE:

This setup is used for most applications.

Flow

Polyglass

Media Tank

¥1FOUBJS'JMUSBUJPO*OD

*OEJBOB"WFOVFr10#PYr4IFCPZHBO8JTDPOTJO

$VTUPNFS4FSWJDFr'BYrTVQQPSUTQFDJBMJTU!QFOUFLàMUSBUJPODPN

*OUFSOBUJPOBMr'BYrJOUFSOBUJPOBM!QFOUFLàMUSBUJPODPN

XXXQFOUFLàMUSBUJPODPN 1SJOUFEJO64"0$

POINT-OF-USE

SySTEmS

VCT-1

Virus Reduction

UF Systems

VGS-600 and VCT-1

VGS-600

The VGS-600 and VCT-1 Virus Reduction UF Systems provide reliable virus, bacteria and protozoan cyst reduction for safer and cleaner drinking water without incorporating chemicals into the media or to the filtered water. These systems are uniquely designed with integral carbon block and sediment pre-filtration for the reduction of chlorine taste and odor and for providing extended life of the internal membrane element.

The systems utilize cartridges that are designed with greater filtration surface area than alternative anti-microbial carbon blocks and operate at a higher flow rates with lower pressure drops. This makes the

VGS-600 and VCT-1 Virus Reduction Systems ideal for Point-of-Use (POU) applications.

The VGS-600 and VCT-1 systems are tested and certified to NSF P231 – Microbiological Water Purifiers.

Tested and Certified by NSF International to

NSF P231 – Microbiological Water Purifiers based on the recommendations set forth in the USEPA Guide Standard and Protocol for

Microbiological Water Purifiers (OPP Task

Force Report, 1987). NSF/ANSI Standard 42 for the reduction of Chlorine Taste and Odor and NSF/ANSI Standard 53 for the reduction of cyst and turbidity.

Typical Applications

• Under Sink, Separate Tap

• Drinking Water Fountains

• Food Preparation and

Hand Washing

• Photography/Film

• Coffee Makers

• Offices, Restaurants

POINT-OF-USE

SySTEmS

VGS-600

Virus Reduction

UF Systems

VGS-600 and VCT-1

VCT-1

Operating Specifications

Pressure Range 30-80 psi (2.07-5.5 bar)

Filter Capacity 600 gallons (2,271 L)

Temperature Range 40-100°F (4.4-38°C)

Rated Service Flow

VGS-600:

VCT-1:

1.35 GPM @ 60 psi

(5.1 Lpm @ 4.1 bar)

0.94 GPM @ 60 psi

(3.78 Lpm @ 4.1 bar)

Features and Benefits

•

Protects and Cleans –

Removes virus, bacteria, cysts, and other particles down to 0.015 micron in size without relying on the addition of chemicals to the water.

•

No Pump Necessary –

Requires only water pressure to operate – no need for an electric pump.

•

Application –

Provides reduction of microorganisms in the water system due to water main breaks or water treatment failure during floods and power outages.

•

No Maintenance –

No waste water or brine/concentrate flushing – simply replace cartridge.

•

Maximum Filtration –

Extra large filtering surface resists clogging.

•

Powerful Flow –

Utilizes polysulfone membrane with proprietary membrane formulation to deliver high flow at low pressure drop.

•

Longer Life –

Combined

Fiberdyne

™

carbon block and sediment pre-filtration for extended life and chlorine taste and odor reduction.

•

PENTEK

Protection –

Double O-ring end cap seals for robust sealing in PENTEK

Seal-Safe

3G housings.

•

No Fouling –

Filter not susceptible to common substances in water, such as hydrogen sulfide (H

2 natural organic matter

S),

(NOM), and total dissolved solids (TDS). Retains natural mineral content of water.

EPA Est. No. 039861-WI-001

Not certified for sale in California, Iowa and Wisconsin.

WARNING: These systems are intended for the disinfection of microbiologically contaminated water that meets all other public health standards. These systems are not intended for the treatment of water that has an obvious contamination or intentional source, such as raw sewage. These systems are not intended to convert wastewater or raw sewage into potable drinking water.

These systems are intended for use on visually clear water.

Operating Specifications – VGS-600 and VCT-1 with DVG-50 Cartridge

Substance

P231

Bacteria: Raoultella terringena (ATCC-33257)

Virus: MS-2 (ATCC-15597-B1)

STANDARD 42

Chlorine Taste & Odor

STANDARD 53

Turbidity

Cyst

Influent

Challenge

Concentration

2.8 x 10

/ 100 mL

4.3 x 10

/ mL

2.0 mg / L ± 10%

11 ± 1 NTU

Min 50,000 / L

Max. Permissible

Product Water

Concentration

0.5 NTU

Reduction

Requirements

Average

Reduction

≥ 99.9999%

≥ 99.99%

≥ 50%

99.95%

7.43 log

4.66 log

97.4%

99%

99.99%

20580 Enterprise Avenue

Brookfield, WI 53045

Tel: 262.784.4490

Fax: 262.784.7794

5730 North Glen Park Road milwaukee, WI 53209

Tel: 262.238.4400

Fax: 262.238.4402

Customer Care: 800.279.9404 www.pentairaquapro.com

311005 Rev A my10

Water Systems, Inc.

5301 Airport Rd.

Cle Elum, WA 98922

509 ‐ 674 ‐ 4000 F.

509 ‐ 674 ‐ 4002

Web: www.o3water.com

and www.cascadianwater.com

Integrated

Cartridge

Solutions

Built

in

the

Northwest

for

Northwest

Waters

System

Benefits

Include

• Environmentally

Green

‐

100%

Efficient

• Low

Cost

High

Quality

Water

• High

Flow

and

High

Volume

• Compact

size;

Installs

Almost

Anywhere

• Easy

Installation;

No

Drain

or

Power

Required

• Long

Life,

Low

Maintenance

Lifestyle

Benefits

Include

• Better

Tasting,

Smelling

and

Looking

Water

• No

Orange

and

Brown

Staining

• Cleaner

Brighter

Laundry

• Reduced

Spotting

‐

Save

on

Cleaning

and

Maintenance

• Protection

for

Pipes

and

Water

Heaters

• Extended

Appliance

Life

and

Reduced

Maintenance

CASCADIAN

ICS

Integrated

Cartridge

Solutions

Include:

• Mineral / Hardness Deposits

• Orange, Red, Brown, Black and Blue Stains

• Etching and Pitting

• Bad Taste and Odor

• Chlorine Taste and Odor

• Low pH problems

• Sediment and Solids

• Cloudy Turbid Water

• Appliance / Pipe Corrosion

CASCADIAN

ICS

‐

Integrated

Cartridge

Solutions

The ICS line of cartridge filter solutions is designed from the ground up with quality and reliability in mind.

ICS solutions will reliably treat water quality problems for years to come.

Capable of treating up to 15 GPM with 1” connections ICS solutions are built from NSF approved components with cartridge filters specially designed for long lasting dependable results.

Where budget or space are a concern the

ICS Solutions are a great alternative to our fully automatic

CASCADIAN

Professional Solutions.

ICS Solution Benefits:

• Systems are fully assembled and ready install.

• Easily install just about anywhere ‐ no power or drain required.

• Large filters result in fewer filter cartridge changes and less maintenance.

• Easy Maintenance – simply change the cartridges in a few minutes.



Protect



Prevent



Save

Water Treatment – “Its what we know, Its all we do”

CASCADIAN

Professional Water Treatment Products Since 1994

Ph.

509 ‐ 674 ‐ 4000



Fax: 509 ‐ 674 ‐ 4002

 www.CascadianWater.com

Integrated

Cartridge

Solutions

Built

in

the

Northwest

for

Northwest

Waters

CASCADIAN

ICS

‐

Integrated

Cartridge

Solutions

ICS Integrated Cartridge Solutions use one, two or three large cartridge filters and each is designed for specific problems.

ICS solutions are the best alternative available to our fully automatic

CASCADIAN

Professional Solutions.

Single Filter Solutions

• S5 – Sediment filtration down to 5 microns

• P06 and P12 – PolyHalt™ iron, manganese, hardness deposits, etching, pitting, appliance protection – 6 or 12 gpm

Double Filter Solutions

• SI – Sediment and soluble Iron

• SP06 and SP12 – Sediment with PolyHalt

™ iron, manganese, hardness, etching, pitting, appliance protection – 6 or 12 gpm

• SS51– Sediment filtration 50 to 1 micron

• SS75 – Sediment filtration 75 to 5 micron

• ST – Sediment, taste and odor

• TO – Taste and odor

Triple Filter Solutions

• SIP – Sediment, soluble iron with PolyHalt

™

• SIT – Sediment, soluble iron, taste and odor

• PWC06 and PWC12 – PolyHalt

™

Salt Free Water Conditioning System 6 or 12 gpm

All ICS two and three filter solutions are pre ‐ assembled, leak tested and complete with filter wrench and extra O ‐ ring.

General Specifications:

• Maximum Flow Rate – 12 ‐ 15 gpm.

• Pressure Drop at 10 gpm ‐ 8 psi.

(typical when new).

• Maximum Dimensions;

Single Filter Systems – 8½” x 8½” x 26½”

Double Filter Systems – 15¼” x 8½” x 26½”

Triple Filter Systems – 23¼” x 8½” x 26½”

• In and Out Pipe Size – 1”

• Soluble Iron Removal;

27,000 gal.

@ 3 ppm, 40,000 gal.

@ 2 ppm,

80,000 gal.

@ 1 ppm and 160,000 gal.

@ 0.5

ppm soluble iron.

•

Single

S5 ‐

P06

P12

Have

‐

Filter

spare

Kits

SS75 ‐

•

SP06 ‐ K

•

SP12 ‐ K

•

SS51 ‐ K

Ready: replacement

•

‐

filter

Double Filter Kits

‐

kit

•

at all

Triple

SIP

SIT

‐

times

Filter

PWC06

PWC12 ‐

‐ K

Kits

Recommended Operating Conditions:

• All ICS Products: Maximum Pressure – 90 psi.

Maximum Temperature ‐ 100°

• SI and SIT Solutions: For soluble iron removal; pH >7.0, Silica <100, Manganese <1 ppm, Iron <3 ppm,

Iron Bacteria – None, Hydrogen Sulfide – None

• PolyHalt

™

Cartridge Limits: Soluble iron and manganese – 6 ppm combined, hardness – 10 grains (171 ppm) silica 100 ppm, Not Recommended for use on Irrigation Systems or in hot water circulating loops

10 Year Warranty:

In the unlikely event that you have trouble with your ICS system we will at our option repair, modify or replace it at no cost to you.

To qualify for tis warranty use only replacement cartridge kits which are designed for the ICS Integrated Cartridge

Solutions and available from O

Water Systems or its distributors.

See warranty online at www.CascadianWater.com



Protect



Prevent



Save

Water Treatment – “Its what we know, Its all we do”

CASCADIAN

Professional Water Treatment Products Since 1994

Ph.

509 ‐ 674 ‐ 4000



Fax: 509 ‐ 674 ‐ 4002

 www.CascadianWater.com

CASCADIAN

PolyHalt

™

Protection

Systems

For

On

Demand

/

Tankless

Water

Heaters

and

Boiler

Makeup

Water

CASCADIAN®

PolyHalt

™

Protection

System

Benefits

Include:

• Prevent

Scale

Buildup,

Corrosion

and

Sediment

Deposits

• Simple

Proven

Low

Cost

Protection

to

Extend

Energy

Efficiencies

and

Life

of

all

Tankless

Water

Heaters

• Environmentally

Green

‐

100%

Efficient,

No

Need

for

Chemical

Cleaning

• High

Flow

– Low

Pressure

Drop

• Low

Cost

Maintenance

– Simply

Change

Cartridges

Annually,

No

Salt

or

Chemicals

• Reduce

Service

and

Repair

Costs

• Compact

size;

Installs

Anywhere

‐

Inside

or

Outside

• Commercial

Quality,

1”

In

and

Out

Housing

CASCADIAN

PolyHalt

™

On

Demand

/

Tankless

Water

Heater

Protection

PolyHalt ™ Protection Systems provide long term protection against deposits of sediment and scale within the heating chamber of your On Demand / Tankless Water Heater.

These deposits prevent efficient transfer of heat to water and lead to premature failure.

Built with quality and reliability in mind, PolyHalt ™ water quality problems for years to come.

Protection Systems will reliably treat

Simply choose the appropriate size base upon your heater flow rate (6 gpm or 12 gpm) and install in the cold water feed line to protect your On Demand / Tankless Water

Heater.

Protect Everything ‐ As an option PolyHalt

™

Protection Systems can be used at the water source to treat all the water throughout your home or business.

Higher flow systems available.

Added PolyHalt

™

Protection System Benefits:

• Systems are fully assembled and ready install.

• Easily install just about anywhere ‐ no power or drain required.

• Large high capacity filters result in fewer filter cartridge changes and less maintenance.

Estimated Life – Hot water only – 8 to 12 months; Whole house or business – 4 to 6 months.

• Easy Maintenance – simply change the cartridges in a few minutes.



Protect



Prevent



Save

Water Treatment – “Its what we know, Its all we do”

CASCADIAN

Professional Water Treatment Products Since 1994

Ph.

509 ‐ 674 ‐ 4000



Fax: 509 ‐ 674 ‐ 4002

 www.CascadianWater.com

CASCADIAN

PolyHalt

™

Protection

Systems

For

On

Demand

/

Tankless

Water

Heaters

and

Boiler

Makeup

Water

CASCADIAN

PolyHalt

™

On

Demand

/

Tankless

Water

Heater

/

Boiler

Makeup

Water

Protection

Against:

• Efficiency Losses and Premature Product Failure

• Mineral and Hardness Scale Deposits

• Corrosion

• Etching and Pitting

• Iron Deposits

• Orange, Red, Brown, Black and Blue Stains

• Low pH problems

• Sediment and Solids Deposits

General Specifications:

• Maximum Flow Rate

• SP06 – 6 gpm

• SP12 ‐ 12 gpm

• Pressure Drop at 10 gpm ‐ 8 psi.

(typical when new)

• Maximum Dimensions;

Double Filter Systems – 15¼” x 8½” x 26½”

• In and Out Pipe Size – 1”

• Maximum Soluble Iron – 6 ppm

Recommended Operating Conditions:

• Maximum Hardness – 10 grains (171 ppm)

• Maximum Pressure – 90 psi.

• Maximum Temperature ‐ 100°

• Not

Recommended for Irrigation Water

• For use with non ‐ recirculating cold water only

•

SP12

Be Ready:

Have a spare replacement filter kit at all times

PolyHalt ™ Part Number

•

SP06

Replacement

•

SP06

SP12 ‐

‐ K

Cartridge

All PolyHalt ™ Protection Systems are pre ‐ assembled, leak tested and complete with filter wrench, an extra O ‐ ring and O ‐ ring lubricant.

For additional cartridge based water treatment solutions please ask for information on the

CASCADIAN® ICS – Integrated Cartridge Solutions Series

Kit

COMPONENT

Cartridges Tested and Certified by NSF

International against NSF/ANSI Standard

42 for material requirements only.

COMPONENT

Filter Housings Tested and Certified by NSF

International against NSF/ANSI Standard 42 for material requirements only.

PolyHalt™ Phosphate Material is

Certified by NSF to NSF/ANSI Standard

60 for Drinking Water Treatment

Chemicals ‐ ‐ Health Effects.

Water Treatment – “Its what we know, Its all we do”

CASCADIAN

Professional Water Treatment Products Since 1994

Ph.

509 ‐ 674 ‐ 4000



Fax: 509 ‐ 674 ‐ 4002

 www.CascadianWater.com

CASCADIAN

ICS ‐ PolyHalt

™

Water Conditioning Systems

Salt

Free

Solution

to

Water

Quality

Problems

CASCADIAN®

PolyHalt

™

Water Conditioning Systems:

• Prevent

Scale

Buildup,

Corrosion

and

Sediment

Deposits

• Improve

Water

Taste

and

Odor

Problems

(PWC Series)

• Simple

Proven

Low

Cost

Water

Conditioning

• Environmentally

Green

‐

100%

Efficient,

No

Need

for

Chemical

Cleaning

• Condition

All

Potable

Water

Sources

• High

Flow

– Low

Pressure

Drop

• Low

Cost

Maintenance

– Simply

Change

Cartridges

Annually,

No

Salt

or

Chemicals

• Reduce

Service

and

Repair

Costs

While

Extending

Appliance

Life

• Compact

size;

Installs

Anywhere

‐

Inside

or

Outside

CASCADIAN

ICS ‐ PolyHalt

™

Salt Free Water Conditioning

Simplify your water treatment needs with PolyHalt ™ Salt Free Water Conditioning Systems.

Addressing many water quality problems that till now were only treatable with larger more expensive water conditioning systems.

PolyHalt

™

Salt produce high quality water straight from the source.

Free Water Conditioning Systems

Every PolyHalt

™ system uses a high quality depth filter to remove particles down to 5 micron size in the first housing.

The three housing systems provide the added benefit of a high quality taste and odor filter in the middle housing.

The final housing contains PolyHalt

™ material that prevents corrosion, hardness problems scale buildup, staining and more.

Simply choose with or without the Taste and Odor feature and your flow rate (6 gpm or 12 gpm) and install in the cold water line and enjoy your water quality.

Added PolyHalt

™

Salt Free Water Conditioning System Benefits:

• Every system is fully assembled and ready install.

• No need to buy bottled water, convenient high quality water at every tap.

• Environmentally friendly – No plastic water bottles, no salt or electricity required.

• Easily install just about anywhere – compact size, no power or drain required.

• Large high capacity filters mean fewer filter cartridge changes and less maintenance.

• Easy Maintenance – simply change cartridges in a few minutes.



Protect



Prevent



Save

Water Treatment – “Its what we know, Its all we do”

CASCADIAN

Professional Water Treatment Products Since 1994

Water Systems, Inc.

Ph.

509 ‐ 674 ‐ 4000



Fax: 509 ‐ 674 ‐ 4002

 www.CascadianWater.com

CASCADIAN

ICS ‐ PolyHalt

™

Water Conditioning Systems

Salt

Free

Solution

to

Water

Quality

Problems

CASCADIAN

ICS ‐ PolyHalt

™

Water Conditioning Systems:

• Mineral and Hardness Scale Deposits

• Corrosion

• Etching and Pitting

• Taste and Odor Including Chlorine

(PWC Series)

• Iron Deposits

• Orange, Red, Brown, Black and Blue Stains

• Low pH problems

• Sediment and Solids Deposits

General Specifications:

• Maximum Flow Rate

• SP06 – 6 gpm

• SP12 ‐ 12 gpm

• PWC06 – 6 gpm

• PWC12 – 12 gpm

• Pressure Drop at 10 gpm ‐ 8 psi.

(typical when new)

• Maximum Dimensions;

SP06 and SP12 Systems – 15¼” x 8½” x 26½”

PWC06 and PWC12 Systems – 23¼” x 8½” x 26½”

• In and Out Pipe Size – 1”

• Maximum Soluble Iron / Manganese – 6 ppm

• Maximum Hardness – 10 grains (171 ppm)

Be Prepared:

Have a spare replacement filter kit at all times

PolyHalt

™

Part Number

Recommended Operating Conditions:

• Maximum Pressure – 90 psi.

• SP06

• SP12

• Maximum Temperature ‐

• Not Recommended for

100°

Irrigation Water

• PWC06

• PWC12

• For use with non ‐ recirculating cold water only

• Estimated Cartridge Life – Hot water only – 1 Year; Whole house or business – 6 months.

Replacement

•

SP06

SP12

‐

PWC06

PWC12 ‐

‐ K

Cartridge Kit

10 Year Warranty:

In the unlikely event that you have trouble with your ICS system we will at our option repair, modify or replace it at no cost to you.

To qualify

for tis warranty use only replacement cartridge kits which are designed for the ICS Integrated Cartridge

Solutions and available from O

Water Systems or its distributors.

See warranty online at www.CascadianWater.com

All PolyHalt

™

Protection Systems are pre ‐ assembled, leak tested and complete with filter wrench, an extra O ‐ ring and O ‐ ring lubricant.

For additional cartridge based water treatment solutions please ask for information on the

CASCADIAN® ICS – Integrated Cartridge Solutions Series

COMPONENT

Cartridges Tested and Certified by NSF

International against NSF/ANSI Standard

42 for material requirements only.

COMPONENT

Filter Housings Tested and Certified by NSF

International against NSF/ANSI Standard 42 for material requirements only.

Water Treatment – “Its what we know, Its all we do”

CASCADIAN

Professional Water Treatment Products Since 1994

Ph.

509 ‐ 674 ‐ 4000



Fax: 509 ‐ 674 ‐ 4002

 www.CascadianWater.com

PolyHalt™ Phosphate Material is

Certified by NSF to NSF/ANSI Standard

60 for Drinking Water Treatment

Chemicals ‐ ‐ Health Effects.

S1 SERIES PLEATED CELLULOSE SEDIMENT

• Pleated design maximizes dirt-holding capacity

• Designed for general water filtration purposes

• Economically priced

• Nominal 20-micron rating

S1-20

S1 S1-BB

S1-20BB

P SERIES SPUN-BONDED POLYPROPYLENE

• Manufactured from pure 100% polypropylene

• Designed for purity, bacteria and chemical resistance

• Spun fibers form a true gradient density from outer to inner surfaces

P5-478

P5-20

P5-30

DGD SERIES DUAL-GRADIENT DENSITY

• Manufactured from 100% pure polypropylene

• Designed for purity, with bacteria and chemical resistance

• Two separate gradient density layers enhance cartridge performance

• Three times the dirt-holding capacity of similar-sized sediment cartridges

DGD-2501

DGD-2501-20

CW/WP SERIES POLYPROPYLENE WOUND

• String-wound design reduces fine sediment from a variety of fluids

• Withstands temperatures up to 165˚F (74˚C)

• Economically priced

• Nominal 5-, 20-, 50-micron rating (CW) and nominal 5-, 30-micron rating (WP)

CW-F

CW-50

CW-MF

CP5-20 CP5-20BB

CP SERIES PLEATED CELLULOSE POLYESTER

• Special formulation of resin-impregnated cellulose and polyester fibers

• Provides higher wet strength than regular cellulose cartridges

• No unloading and minimal media migration

CP-1

CP-5 CP5-BB

Materials of Construction

• Filter Media:

Resin-Impregnated Cellulose

• End Caps:

Vinyl Plastisol

• Core:

Polypropylene

• Netting:

Polyethylene

• Temperature Rating:

40˚F to 145˚F (4.4˚C to 63˚C)

Materials of Construction

• Filter Media:

Polypropylene Fibers

• Temperature Rating:

40˚F to 145˚F (4.4˚C to 63˚C)

Materials of Construction

• Filter Media:

Polypropylene

• Temperature Rating:

40˚F to 145˚F (4.4˚C to 63˚C)

Materials of Construction

• Filter Media:

Polypropylene Fiber Cord

• Core:

Polypropylene

• Temperature Rating:

40˚F to 165˚F (4.4˚C to 74˚C)

Materials of Construction

• Filter Media:

Cellulose Polyester

• Core:

Polypropylene

• End Caps:

Vinyl Plastisol

• Maximum Temperature:

125˚F (52˚C)

HFCP SERIES PLEATED CELLULOSE POLYESTER

• Special formulation of resin-impregnated cellulose and polyester fibers

• Provides higher wet strength than regular cellulose cartridges

• No unloading and minimal media migration

• Designed for high flow rate and high dirt-holding applications

Materials of Construction

• Filter Media:

Cellulose Polyester

• Core:

Vented Polypropylene

• End Caps:

Molded Polypropylene

• Netting:

Polyethylene

• Gasket:

Buna-N & EPR

• Temperature Rating:

40˚F to 165˚F (4.4˚C to 74˚C)

HFCP-1 HFCP-5

PP SERIES POLYPROPYLENE PLEATED

• Pleated design maximizes dirt-holding capacity

• Durable polypropylene media resists bacterial attack

• Suitable for municipal or well water applications

• Nominal 30-micron rating

Materials of Construction

• Filter Media:

• Core:

Non-Woven Polypropylene

Polypropylene

• End Caps:

• Netting:

Vinyl Plastisol

Polyethylene (PP-30 only)

• Gasket:

Buna-N & EPR

• Temperature Rating:

40˚F to 145˚F (4.4˚C to 63˚C)

PP-30

PP30-BB

R SERIES PLEATED POLYESTER

• Pleated design maximizes dirt-holding capacity

• Versatile and reusable, allowing for a variety of uses

• Durable polyester media is bacteria and chemical resistant

• Nominal 30-micron rating (R-30) and nominal

50-micron rating (R-50)

Materials of Construction

• Filter Media:

Non-Woven Polyester

• Core:

Polypropylene

• End Caps:

Vinyl Plastisol

• Temperature Rating:

40˚F to 125˚F (4.4˚C to 52˚C)

R30-20 R30-BB

R50

R50-BB

R30

CRE SERIES CERAMIC

• Specially designed for cyst reduction and fine sediment filtration applications

• 1/2" thick ceramic wall allows for many cleanings, extending cartridge life

• Nominal 1-micron rating

Materials of Construction

• Filter Media:

Sintered Ceramic

• End Caps:

Thermoset Polymeric

• Gasket:

Buna-N

• Temperature Rating:

40˚F to 125˚F (4.4˚C to 52˚C)

CRE-1

POLYDEPTH

™

POLYPROPYLENE SEDIMENT

• Quality polypropylene filter media

• Will not impart taste, odor or color

• Superior chemical resistance. Not prone to bacterial attack

• Compatible with a wide range of industrial filtration

• Available in a wide range of micron ratings and lengths

Materials of Construction

• Filter Media:

Polypropylene

• Temperature Rating:

40˚F to 175˚F (4.4˚C to 79.4˚C)

POLYDEPTH ™

Polypropylene

Sediment

Cartridge

C1-20

C1-20BB

NCP-20

C SERIES DUAL PURPOSE POWDERED-

ACTIVATED CARBON

• Economically priced

• Provides sediment filtration and taste, odor and chlorine reduction

• High dirt-holding capacity

• Available in four sizes and two micron ratings

NCP SERIES NON-CELLULOSE

CARBON-IMPREGNATED PLEATED

• Non-cellulose media resists bacterial attack

• Provides sediment filtration and taste, odor and chlorine reduction

• Pleated for maximum dirt-loading capacity

• Nominal 10-micron rating

Materials of Construction

• Filter Media:

PAC Impregnated Cellulose

• End Caps:

Polypropylene (C8)

Vinyl Plastisol (C1 and C2)

• Netting:

• Core:

Polyethylene

Polypropylene

• Backing:

Polyester(C8) Cellulose Polyester(C1andC2)

• Gasket:

Buna-N (C8) (Optional EPR Gaskets)

• Temperature Rating:

40˚F to 145˚F (C8) (4.4˚C to 63˚C)

40˚F to 125˚F (Others)

(4.4˚C to 52˚C)

Materials of Construction

• Filter Media:

Pleated Carbon-Impregnated Polyester

• End Caps:

Vinyl Plastisol

• Core:

Polypropylene

• Netting:

Polyethylene

• Temperature Rating:

40˚F to 150˚F (4.4˚C to 65.6˚C)

NCP-10

NCP-BB

NCP-20BB

GAC-20

GAC-10

GAC-5

GAC-BB

GAC-20BB

GAC SERIES GRANULAR ACTIVATED CARBON

• Effective taste, odor and chlorine reduction

• Designed for maximum adsorption

• Post-filter to reduce carbon fines

• Available in a variety of sizes and flow rates

Materials of Construction

• Filter Media:

Granular-Activated Carbon

• End Caps:

Polystyrene

• Post-filter:

Spun Polypropylene

• Outer Casing:

Polystyrene

• Expansion Pad:

• Gaskets:

Polyester

Buna-N (top) Santoprene (bottom)

• Temperature Rating:

40˚F to 125˚F (4.4˚C to 52˚C)

CC SERIES COCONUT SHELL GRANULAR

ACTIVATED CARBON

• Effective taste, odor and chlorine reduction

• Greater VOC reduction than standard GAC cartridges

• Post-filter to reduce carbon fines

• Available in a variety of sizes and flow rates

Materials of Construction

• Filter Media:

Granular Activated Carbon

• End Caps:

Polystyrene

• Core:

Spun Polypropylene

• Outer Casing:

Polystyrene

• Expansion Pad:

• Gaskets:

Polyester

Buna-N (Top) Santoprene (Bottom)

• Temperature Rating:

40˚F to 125˚F (4.4˚C to 52˚C)

CC-10

CC-BB

CC-20

CC-20BB

CGAC-10 GRANULAR ACTIVATED CARBON

• Effective taste, odor, chlorine, and chloramine reduction

• Advanced catalytic carbon media

• Designed for maximum adsorption

• Post-filter to reduce carbon fines

Materials of Construction

• Filter Media:

Catalytic Carbon

• End Caps:

Polystyrene

• Post-filter:

Spun Polypropylene

• Outer Casing:

Polystyrene

• Expansion Pad:

Polyester

• Gaskets:

Buna-N (top) Santoprene (bottom)

• Temperature Rating:

40˚F to 125˚F

(4.4˚C to 52˚C)

CGAC-10

SGAC SERIES SILVER-IMPREGNATED

GRANULAR ACTIVATED CARBON

• Effective taste, odor and chlorine reduction

• Silver-impregnated carbon media inhibits the growth of bacteria

• Designed for maximum adsorption

• Post-filter to reduce carbon fines

Materials of Construction

• Filter Media:

Silver-Impregnated

Granular-Activated Carbon

• End Caps:

• Post-filter:

Polystyrene

Spun Polypropylene

• Outer Casing:

Polystyrene

• Gaskets:

Buna-N (top) Santoprene (bottom)

• Temperature Rating:

40˚F to 125˚F (4.4˚C to 52˚C)

SGAC-10

TSGAC SERIES SPECIALTY GRANULAR

ACTIVATED CARBON/PHOSPHATE

• Effective taste, odor and chlorine reduction

• Phosphate crystals reduce rust stains and scale deposits

• Designed for maximum adsorption

• Post-filter to reduce carbon fines

Materials of Construction

• Filter Media:

Granular-Activated Carbon

Hexametaphosphate Crystals

• End Caps:

• Post-filter:

Polystyrene

Spun Polypropylene

• Outer Casing:

Polystyrene

• Expansion Pad:

• Gaskets:

Polyester

Buna-N (top) Santoprene (bottom)

• Temperature Rating:

40˚F to 125˚F (4.4˚C to 52˚C)

RFC SERIES RADIAL FLOW CARBON

• Ideal for point-of-entry (POE) and other high flow rate applications

• Unique design reduces carbon fines in filtered water

• Available in a wide variety of sizes

Materials of Construction

• Filter Media:

Granular Activated Carbon

• End Caps:

Polypropylene

• Outer Shell:

Polyethylene

• Inner/Outer Wrap:

Polypropylene

• Gaskets:

Buna-N

• Temperature Rating:

40˚F to 125˚F (4.4˚C to 52˚C)

RFC20-BB

TSGAC-10

RFC-93 RFC-BB

RFC-20

EPM SERIES MODIFIED EPSILON

CARBON-BRIQUETTE

• Economically priced

• High porosity maximizes utilization of the carbon block

• Greater chlorine-removal capacity than competitive 10-micron carbon blocks.

• Nominal 10-micron rating

Materials of Construction

• Filter Media:

Bonded PAC

• End Caps:

• Netting:

Polypropylene

Polyethylene

• Outer Wrap:

• Gaskets:

Polypropylene

Buna-N

• Temperature Rating:

40˚F to 180˚F (5˚C to 83˚C)

EPM-10

EPM-BB

EPM-20BB

EPM-20

EP SERIES CARBON-BRIQUETTE

• High-dirt-holding tolerance maximizes utilization of the carbon block

• Greater chlorine reduction capacity than competitive 10-micron carbon blocks

• Nominal 5-micron rating

Materials of Construction

• Filter Media:

• End Caps:

Bonded PAC

Polyethylene

• Netting:

Polypropylene

• Inner/Outer Wrap:

Polypropylene

• Gaskets:

Buna-N

• Temperature Rating:

40˚F to 180˚F (5˚C to 83˚C)

EP-20

EP-10

EP-BB

EP20-BB

CBC-20BB

CBC SERIES CARBON-BRIQUETTE

• Reduces taste, odor, chlorine and certain VOCs from drinking water

• Effective at filtering

Giardia

cysts

Cryptosporidium

and

• High capacity chlorine reduction

• Nominal 0.5-micron rating

Materials of Construction

• Filter Media:

Bonded PAC

• End Caps:

Polypropylene

• Inner/Outer Wraps:

Polypropylene

• Netting:

Polyethylene

• Temperature Rating:

40˚F to 180˚F (5˚C to 83˚C)

CBC-BB

CBC-5

CBC-20

CBC-10

CCBC-10

CCBR2-10

CBR2-10

CBR2-10R

CCBC SERIES COCONUT BASED

CARBON BLOCK

• Water-washed coconut-carbon formulation

• Reduces taste, odor, chlorine and certain VOCs from drinking water

• Effective at filtering

Cryptosporidium

and

Giardia

cysts

• Nominal 1-micron rating

Materials of Construction

• Filter Media:

Water-Washed Coconut Based Carbon

• End Caps:

Polypropylene

• Inner/Outer Wraps:

• Netting:

Polypropylene

Polyethylene

• Gaskets:

Buna-N

• Temperature Rating:

40˚F to 180˚F (5˚C to 83˚C)

CBR2 SERIES CARBON-BRIQUETTE MULTIMEDIA

• Highly effective chlorine reduction through more than 20,000 gallons

• Lead reduction through 2000 gallons

• 99.95% reduction of Cryptosporidium and

Giardia cysts

• Nominal 0.5-micron sediment filtration

Materials of Construction

• Filter Media:

Bonded PAC

• End Caps:

Polypropylene

• Outer Wrap:

Polypropylene

• Netting:

Polyethylene

• Gaskets:

Buna-N

• Temperature Rating:

40˚F to 180˚F (4.4˚C to 83˚C)

CEP-20E

CEP SERIES COCONUT BASED CARBON BLOCK

• Acid-washed coconut-carbon formulation

• Low extractables, minimal pH rise

• Greater chlorine removal capacity than competitive 10-micron carbon blocks

• Nominal 5-micron rating

Materials of Construction

• Filter Media:

Acid-Washed Coconut Based Carbon

• End Caps:

Polypropylene

• Inner/Outer Wraps:

Polypropylene

• Netting:

• Gaskets:

Polyethylene

Buna-N

• Temperature Rating:

40˚F to 125˚F (5˚C to 52˚C)

CEP-10E

CEP-20BB

CEP-10BB

OAC-20BB OIL ABSORBING

• High efficiency removal of oils or glycol

• Instantaneous absorption, more effective than activated carbon

• 90% of total hydrocarbons are removed in a single pass

• For use in 20-inch Big Blue ® filter housings

Materials of Construction

• Filter Media:

Modified Cellulose

• End Caps:

PVC Plastisol

• Core:

Natural Polypropylene

• Netting:

Polyethylene

• Temperature Rating:

• Media Area:

40˚F to 125˚F (4.4˚C to 52˚C)

18 sq ft (1.6 sq m)

• Weight:

2.0 lbs (0.7 kg)

OAC-20BB

WS SERIES WATER SOFTENER

• Convenient cartridge change-out

• Manufactured with FDA-grade softener resin

• 750 to 4,500 grain capacity available (CaCo3)

• For use in standard and Big Blue ® filter housings

Materials of Construction

• Filter Media:

Standard Softener Resin

• End Caps:

Polypropylene

• Gasket:

Buna-N

• Temperature Rating:

100˚F (38˚C)

WS-10

WS-20

WS-20BB

PCC SERIES HEXAMETAPHOSPHATE CRYSTAL

• Highly effective at treating scale, corrosion and iron problems

• Ideal for a variety of food service equipment, as well as other types of water processing equipment

Materials of Construction

• Filter Media:

• Shell:

Food Grade Polyphosphate

Polypropylene

• Pre-Filter:

• Post-Filter:

Polyester

Polypropylene

• Gaskets:

Buna-N

• Temperature Rating:

40˚F to 100˚F (4.4˚C to 38˚C)

PCC212

PCC218

PCC10

PCC1

RADIAL FLOW IRON REDUCTION

• Easily and effectively reduces iron in water up to 3 ppm

• Improves flavor and reduces the metallic taste caused by iron

• Reduces the possibility of pipe and water heater damage

• For use in 20-inch Big Blue ® filter housings

Recommended Operating Conditions

• pH:

• Iron:

>7.0

• Silica:

<100 ppm

• Manganese:

<3 ppm

<1 ppm

• Iron Bacteria:

None

• Hydrogen Sulfide:

None

BP SERIES POLYPROPYLENE BAGS

• Thermally welded seams result in consistent filtration efficiencies

• Increased surface area means less frequent bag changes

• Semi-rigid cylindrical design is easily crushed and incinerated

Materials of Construction

• Top:

Polypropylene

• Filter Media:

Felt

• Micron Rating:

1 - 200

• Maximum Temperature:

200˚F (93˚C)

RFFE20-BB

PCF SERIES MIXED BED DEIONIZATION

• Designed for deionizing water up to 16 megaohms

• All materials and construction are FDA-compliant

• Three sizes and capacities

Materials of Construction

• Filter Media:

Mixed bed DI resins

• End Caps:

• Shell:

Polypropylene

• Pre-Filter:

• Post-Filter:

Polyester

Polypropylene

• Gaskets:

Buna-N

• Temperature Rating:

40˚F to 100˚F (4.4˚C to 38˚C)

PCF1-10MB

PCF1-20MB

BBF1-20MB

BP-420

BP-410

C1-20

$4&3*&4%6"-163104&

108%&3"$5*7"5&%$"3#0/$"353*%(&4

C Series cartridges offer an economical solution for all your general-purpose water ﬁltration needs.

Constructed of a carbon impregnated cellulose media, these dual-purpose cartridges ﬁlter out ﬁne sediment particles and reduce unwanted taste, odor, and chlorine taste & odor from your tap water.*

A polyester reinforcement backing and external netting provide additional strength and dirt-loading capacity.

C Series cartridges are available in three (3) different sizes and two (2) different micron ratings. Both the

C1 and C2 are nominally rated at 5-microns, the C8 is nominally rated at 1-micron.

FEATURES

#&/&'*54 t #PUIDIMPSJOFBOETFEJNFOUSFEVDUJPO t )JHInPXSBUFTQPTTJCMFEVFUPMPXJOJUJBMQSFTTVSFESPQ t (PPEEJSUIPMEJOHDBQBDJUZ

C2 t "WBJMBCMFJOUXPEJGGFSFOUNJDSPOTJ[FT t 'JWFQSPEVDUTXJUIBDIPJDFPGUISFFMFOHUITBOEUISFFEJBNFUFST t #BTJDDIMPSJOFSFEVDUJPOBUBWFSZHPPEFDPOPNJDWBMVF

These dual-purpose cartridges are well suited for a wide range of residential applications, and make excellent polishing ﬁlters when used in process or closed-loop streams.

* Based on manufacturer’s internal testing.

"11-*$"5*0/4 t (FOFSBMQVSQPTFUBTUFPEPSSFEVDUJPOGPSSFTJEFOUJBM

DIMPSJOBUFEXBUFSTVQQMJFT t 1PMJTIJOHmMUFSGPSQSPDFTTPSDMPTFEMPPQTUSFBNT

$4&3*&4

%VBM1VSQPTF1PXEFS"DUJWBUFE$BSCPO$BSUSJEHFT

"--$4&3*&4$"353*%(&4

C1-20

1BSUJDMF4J[F .JDSPOT

'MPX3BUFoHQN -QN

$BSUSJEHF4QFDJmDBUJPOTBOE1FSGPSNBODF%BUB

.PEFM

.BYJNVN

%JNFOTJPOT

.JDSPO3BUJOH

/PNJOBM

2 7 ⁄

" x 9 3 ⁄

(64 mm x 248 mm)

CS1

C1-20

⁄

" x 9

⁄

(57 mm x 248 mm)

⁄

" x 4

⁄

(64 mm x 124 mm)

⁄

" x 9

⁄

(67 mm x 248 mm)

2 1 ⁄

" x 20"

(64 mm x 508 mm)

*OJUJBMå1 QTJ!

'MPX3BUF HQN

4 psi @ 5 gpm

(0.3 bar @ 19 Lpm)

4 psi @ 5 gpm

(0.3 bar @ 19 Lpm)

2 psi @ 2 gpm

(0.1 bar @ 7.6 Lpm)

5 psi @ 5 gpm

(0.3 bar @ 19 Lpm)

1 psi @ 5 gpm

(0.1 bar @ 19 Lpm)

#BTFEPONBOVGBDUVSFSTJOUFSOBMUFTUJOH

.BUFSJBMTPG$POTUSVDUJPO

Filter Media

End Caps

PAC Impregnated Cellulose

Polypropylene (C8), Vinyl Plastisol (C1, C2 and CS1)

Netting

Core

Reinforcement Backing

Gasket

Temperature Rating

Polyethylene

Polypropylene

Polyester (C8), Cellulose Polyester (C1 and C2)

Buna-N (C8)

F to 145

F (4.4

C to 62.8

C)(C8), 40

F to 125

F (4.4

C to 51.7

C)(C1, C2, C1-20)

$IMPSJOF5BTUF0EPS3FEVDUJPO

!'MPX3BUF HQN

>5,000 gallons @ 1 gpm

(>11,250 L @ 3.8 Lpm)*

>3,000 gallons @ 1 gpm

(>5,100 L @ 3.8 Lpm)*

>2,500 gallons @ 0.5 gpm*

(>5,600 L @ 7.6 Lpm)

>8,000 gallons @ 1 gpm*

(>30,000 L @ 3.8 Lpm)

>10,000 gallons @ 2 gpm*

(>37,500 L @ 3.8 Lpm)

The C1 is Tested and Certiﬁed by NSF

International to NSF/ANSI Standard 42 for material requirements only.

WARNING:

For drinking water applications, do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the system.

NOTE:

Increased flow rates may result in less effective chlorine reduction.

NOTE:

Some harmless bacteria will attack cellulose media cartridges. If your cartridge seems to disintegrate, or has a musty or moldy odor, switch to a synthetic media cartridge or consult the manufacturer.

NOTE:

Estimated capacity tested at given flow rate using 2 ppm free available chlorine to 0.5 ppm breakthrough.

*OEJBOB"WFOVFr10#PY

Sheboygan, Wisconsin 53082-1047

1IPOF r

'BYr www.pentekfiltration.com

CBC-20BB

CBC SerieS CarBON-BriQUette CartridgeS

• Nominal 0.5-micron rating*

• 99.95% reduction of Cryptosporidium, giardia, entamoeba, and toxoplasma cysts*

• Premium high capacity bad taste & odor and chlorine taste & odor reduction*

• enhanced dirt holding capacity*

CBC-BB

CBC-5

CBC-10

CBC-20

CBC Series cartridges are highly effective at reducing unwanted bad taste and odor, and chlorine taste & odor, from potable drinking water.

The unique structure of the carbon block enables it to reduce Giardia,

Cryptosporidium, Entamoeba, and

Toxoplasma cysts and fine sediment particles down to 0.5 microns.*

CBC Series cartridges are manufactured using a patented process and made entirely from

FDA-compliant materials. They are an ideal choice for a wide range of residential, food service, commercial and industrial applications. They also make excellent polishing filters or pre-filters in applications requiring fine filtration and high capacity.

* Based on manufacturer’s internal testing.

CBC SerieS

Carbon-Briquette Cartridges

$#$

$#$##

'MPX3BUFoHQN -QN

Cartridge Specifications and Performance data

Model Maximum dimensions

Micron rating*

(nominal)

CBC-5

CBC-10

CBC-20

CBC-BB

CBC-20BB

⁄

" x 4

⁄

" (73 mm x 124 mm)

⁄

" x 9

⁄

" (73 mm x 248 mm)

⁄

" x 20" (73 mm x 508 mm)

⁄

" x 9

⁄

" (118 mm x 248 mm)

⁄

" x 20" (118 mm x 508 mm)

0.5

initial ∆P (psi)

@ Flow rate (gpm)

7.0 psi @ 1 gpm (0.48 bar @ 3.8 Lpm)

3.7 psi @ 2 gpm (0.23 bar @ 7.6 Lpm)

3.0 psi @ 2 gpm (0.21 bar @ 7.6 Lpm)

4.6 psi @ 2 gpm (0.32 bar @ 7.6 Lpm)

8.5 psi @ 4 gpm (0.38 bar @ 15.1 Lpm)

Chlorine taste & Odor reduction @ Flow rate

>3000 gallons @ 1 gpm

(11,400L @ 3.8 Lpm)

>20,000 gallons @ 2 gpm

(75,700L @ 7.6 Lpm)

>45,000 gallons @ 2 gpm

(170,300L @ 7.6 Lpm)

>50,000 gallons @ 2 gpm

(189,300L @ 7.6 Lpm)

>150,000 gallons @ 4 gpm

(567,800L @ 15.1 Lpm)

* Based on manufacturer's internal testing

Materials of Construction

Filter Media

End Caps

Bonded PAC

Polypropylene

Inner/Outer Wraps

Netting

Gaskets

Temperature Rating

Polyolefin

Polyethylene

Buna-N

40–180ºF (4.4–82.2ºC)

WARNING:

Do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the system.

The CBC-10, CBC-20, CBC-BB and CBC-

20BB are Tested and Certified by NSF

International to NSF/ANSI Standard 42 for material requirements only.

NOTE:

Performance capacity depends on system design, flow rate and certain other application conditions. Certain states require system registration or certification for health-related contaminant reduction claims.

NOTE:

Cartridges will contain a very small amount of carbon fines (very fine black powder) and a new cartridge after installation should be flushed with sufficient water to remove all traces of the fines from your water system before using the water. Each time you use your filtered water tap for drinking or cooking purposes it is recommended that you run (flush) the tap for at least 20 seconds prior to using water.

NOTE:

Micron ratings based on 85% or greater removal of given particle size.

NOTE:

CBC-Series cartridges are capable of reducing 99.95% of Cryptosporidium and Giardia cysts. Data obtained from actual particle counts using AC Fine Test Dust and Latex spheres.

† Estimated capacity using 2ppm free available chlorine (FAC) with greater than 90% reduction.

U.S. Patent No. 5,976,432 & 5,823,668

502 Indiana Avenue • P.O. Box 1047 • Sheboygan, Wisconsin 53082-1047

Customer Service: 800.645.0267 • Fax: 888.203.7361 • [email protected]

International: 920.457.9435 • Fax: 920.457.2417 • [email protected]

www.pentekfiltration.com Printed in USA MR06 310078

t70$BOE.5#&SFEVDUJPO

CBR2-10

CBR2 SERIES CARBON BRIQUETTE

MULTI-MEDIA CARTRIDGES

t/PNJOBMNJDSPOSBUJOH tSFEVDUJPOPG$SZQUPTQPSJEJVN(JBSEJB

&OUBNPFCBBOE5PYPQMBTNBDZTUT t-FBESFEVDUJPOUISPVHIHBMMPOT t1SFNJVNIJHIDBQBDJUZDIMPSJOFUBTUFPEPSSFEVDUJPO

FYDFFEJOHHBMMPOT

CBR2-10R

The CBR2-10 and CBR2-10R are advanced multimedia cartridges designed to reduce chlorine taste and odor, dissolved and particulate lead, cysts, MTBE and certain volatile organic chemicals (VOCs).*

CBR2 Series cartridges are manufactured using a patented process, and combine powdered activated carbon (PAC) with a specially designed adsorbent medium for lead and mercury reduction.

These cartridges are protected by Endurawrap ™ , a uniquely formulated polyolefin bilaminate prefilter, designed to significantly increase the useful life of the cartridge by trapping sediment that typically plugs carbon block cartridges.

In addition to lead reduction, the unique structure of the carbon block enables it to reduce Giardia,

Cryptosporidium, Entamoeba and

Toxoplasma cysts and fine sediment particles down to 0.5 microns.*

As with our standard CBC Series carbon block, both the CBR2-10 and CBR2-10R are effective at reducing levels of chlorine taste & odor, MTBE and VOCs.*

The CBR2-10R has a built-in flow restrictor (0.6 gpm) to allow for maximum contact time.

* Based on manufacturer’s internal testing.

CBR2 SERIES

$BSCPO#SJRVFUUF.VMUJNFEJB$BSUSJEHFT

$#3

'MPX3BUFoHQN -QN

$BSUSJEHF4QFDJmDBUJPOTBOE1FSGPSNBODF%BUB

.PEFM

.BYJNVN

%JNFOTJPOT

.JDSPO

3BUJOH

OPNJOBM

*OJUJBMå1 QTJ

!'MPX3BUF HQN

CBR2-10

2 7 ⁄

" x 9 3 ⁄

(73 mm x 124 mm)

0.5

15.0 psi @ 1 gpm

(1.0 bar @ 3.8 Lpm)

CBR2-10R

⁄

" x 9

⁄

(73 mm x 124 mm)

0.5

Flow restricted to 0.6 gpm (2.3 Lpm) with built-in Flow restrictor

#BTFEPONBOVGBDUVSFShTJOUFSOBMUFTUJOH

Cyst Reduction* †

Lead & Mercury Reduction*

>99.95%

2000 gallons @ 0.6 gpm

(7570L @ 3.8 Lpm)

$IMPSJOF5BTUF0EPS

3FEVDUJPO!'MPX3BUF

>20,000 gallons @ 1 gpm

(75,700L @ 3.8 Lpm)

>20,000 gallons @ 0.6 gpm

(75,700L @ 2.3 Lpm)

70$HBMMPOT

!HQN

600 @ 0.6

(2270L @ 2.3 Lpm)

600 @ 0.6

(2270L @ 2.3 Lpm)

.5#&HBMMPOT!

HQN

500 @ 0.6

(1890L @ 2.3 Lpm)

500 @ 0.6

(1890L @ 2.3 Lpm)

.BUFSJBMTPG$POTUSVDUJPO

Filter Media

End Caps

Outer Wrap

Netting

Bonded PAC

Polypropylene

Polyolefin

Polyethylene

Gaskets

Temperature Rating

Buna-N

40–165ºF (4.4–73.9ºC)

NOTE: Certain state require system registration or certification for health-related contaminant reduction claims.

This CBR2-10 and CBR2-10R are Tested and Certiﬁed by NSF International to

NSF/ANSI Standard 42 for material requirements only.

NOTE: Chlorine and lead reduction tests conducted by Pentair Water Treatment at 0.6 gallons per minute with a Pentek Slim Line® (SL) housing.

NOTE: Meets NSF Standard 42 for chlorine taste & odor reduction.*

WARNING: Do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the unit.

† NOTE: Giardia, Cryptosporidium, Entamoeba and Toxoplasma cyst claim based on tests showing greater than 99.95% reduction using NSF Standard 53 protocol.

U.S. Patent No. 5,976,432 & 5,823,668

*OEJBOB"WFOVFr10#PYr4IFCPZHBO8JTDPOTJO

$VTUPNFS4FSWJDFr'BYrTVQQPSUTQFDJBMJTU!QFOUFLàMUSBUJPODPN

*OUFSOBUJPOBMr'BYrJOUFSOBUJPOBM!QFOUFLàMUSBUJPODPN www.pentekfiltration.com Printed in USA AU08 310080

CC SERIES COCONUT SHELL

GRANULAR ACTIVATED CARBON CARTRIDGE

t&GGFDUJWFCBEUBTUFPEPSBOEDIMPSJOFUBTUFPEPSSFEVDUJPO t(SFBUFS70$SFEVDUJPOUIBOTUBOEBSE("$DBSUSJEHFT t1PTUmMUFSUPSFEVDFDBSCPOmOFT t"WBJMBCMFJOBWBSJFUZPGTJ[FTBOEnPXSBUFT

CC Series granular activated carbon cartridges are an excellent choice to reduce unwanted chlorine taste

& odor, and certain VOC's from potable drinking water. CC-10 cartridges also reduce MTBE.

They contain coconut shell based activated carbon, which produces drinking water of exceptional taste and quality and provides better

VOC reduction than standard GAC cartridges.*

The construction of the cartridges allows water to enter at one end and pass through the entire length of the carbon bed before exiting the other end of the cartridge, while an internal expansion pad minimizes channeling or bypass. Before the water exits the cartridge, a 20micron post-filter helps remove carbon fines and other suspended particles from the filtered water. The post-filter is permanently fastened to an innovative support basket ensuring that it is firmly secured, eliminating any potential for bypass.

CC Series cartridges effectively provide good general purpose drinking water filtration.

* Based on manufacturer’s internal testing.

CC-10

USCC-10SL

CC SERIES

$PDPOVU4IFMM(SBOVMBS"DUJWBUFE$BSCPO$BSUSJEHFT

'MPX3BUFoHQN -QN

$BSUSJEHF4QFDJmDBUJPOTBOE1FSGPSNBODF%BUB

.PEFM

.BYJNVN%JNFOTJPOT

.JDSPO3BUJOH

OPNJOBM

CC-10 2 7 ⁄

" x 9 3 ⁄

" (73 mm x 248 mm) 20

*OJUJBMå1 QTJ

!'MPX3BUF HQN

4.5 psi @ 1 gpm (0.3 bar @ 3.8 Lpm)

USCC-10SL 2 1 ⁄

" x 9 3 ⁄

" (64 mm x 248 mm)

#BTFEPONBOVGBDUVSFShTJOUFSOBMUFTUJOH

20 8 psi @1 gpm (0.55 bar @3.8 Lpm)

$IMPSJOF5BTUF0EPS

3FEVDUJPO!'MPX3BUF

7,500 gallons @ 1 gpm

(28,000L @ 3.8 Lpm)

3,500 gallons @ 1 gpm

(13,300L @ 3.8 Lpm)

.BUFSJBMTPG$POTUSVDUJPO

Filter Media

End Caps

Post-Filter

Outer Casing

Expansion Pad

Granular Activated Carbon

Polystyrene

Spun Polypropylene

Polystyrene

Polypropylene

The CC-10 is Tested and Certiﬁed by NSF

International to NSF/ANSI Standard 42 for material requirements only.

The USCC-10SL is Tested and Certiﬁed by

NSF International to NSF/ANSI Standard

42 in model US-550 and US-600. See

Performance Data Sheet for speciﬁc claims.

Gasket

Buna-N (top)

Santoprene (bottom)

Temperature Rating

40–125ºF (4.4–51.7ºC)

NOTE:

Performance capacity depends on system design, flow rate and certain other application conditions. Certain states require system registration or certification for health-related reduction claims.

WARNING:

For drinking water applications, do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the system.

NOTE:

A drinking water cartridge may contain carbon fines (very fine black powder). After installation and before using the water, follow the instructions for flushing the cartridge to remove fines.

NOTE:

It is recommended that you run the tap for 20 seconds prior to using the water for drinking or cooking purposes.

*OEJBOB"WFOVFr10#PYr4IFCPZHBO8JTDPOTJO

$VTUPNFS4FSWJDFr'BYrTVQQPSUTQFDJBMJTU!QFOUFLàMUSBUJPODPN

*OUFSOBUJPOBMr'BYrJOUFSOBUJPOBM!QFOUFLàMUSBUJPODPN www.pentekfiltration.com Printed in USA MR06 310071

CEP-10E

CEP-10E COCONUT BASED CARBON BLOCK CARTRIDGE

• Nominal 5-micron rating*

• Acid-washed coconut-carbon formulation

• Bad taste & odor and chlorine taste & odor reduction*

• Low extractables, minimal pH rise for RO pre- and post-filter applications*

• Enhanced dirt holding capacity*

CEP-10E cartridges are manufactured from an acid-washed coconut-carbon based formulation that minimizes the pH rise and produces better tasting water.

Our patented manufacturing process yields a cartridge with a nominal 5micron filtration rating, low extractables and a minimal pH rise ideal for RO pre- and post-filter applications. A thin-wall, high porosity design helps prevent the cartridge from plugging before its adsorption capacity is exhausted, maximizing the utilization of the carbon while maintaining low pressure drop.

These cartridges are protected by

Endurawrap™, a uniquely formulated polyolefin bilaminate prefilter, designed to significantly increase the useful life of the cartridge by trapping sediment that typically plugs carbon block cartridges.

* Based on manufacturer’s internal testing.

CEP-10E

Coconut Based Carbon Block Cartridge

99.9

2 5 10 20

Particle Size (Microns)

50 100

(1.4)

(1.0)

(2.1)

(1.7)

(0.7)

(0.3)

0 2

(7.6)

(15)

(23)

(30)

Flow Rate – gpm (L/min)

(38)

(45)

Tested and Certified by NSF International to NSF/ANSI Standard 42 for material requirements only.

Cartridge Specifications and Performance Data

Model

Maximum

Dimensions

Micron Rating

(Nominal)*

CEP-10E 2-7/8" x 9-3/4"

(73 mm x 248 mm)

* Based on manufacturer’s internal testing.

Initial

P (psi)

@ Flow Rate (gpm)*

3.0 psi @ 1 gpm

(0.2 bar @ 3.8 L/min)

Chlorine Taste & Odor Reduction*

@ Flow Rate (gpm)

>5,000 gallons @ 1 gpm

(18,900 liters @ 3.8 L/min)

Materials of Construction

• Filter Media

• End Caps

• Inner/Outer Wraps

• Netting

Acid-Washed

Coconut Based Carbon

Polypropylene

Polyolefin

Polyethylene

• Gaskets

• Temperature Rating

Buna-N

40˚F to 125˚F (4.4˚C to 51.7˚C)

WARNING:

Do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the system.

U.S. Patent No. 5,976,432 & 5,823,668

502 Indiana Avenue • P.O. Box 1047 • Sheboygan, Wisconsin 53082-1047

Customer Service: 800-645-0267 • Fax: 888-203-7361 • [email protected]

International: 920-457-9435 • Fax: 920-457-2417 • [email protected]

www.pentekfiltration.com

Printed in U.S.A. MR07 310095

CFB-30

CFB SERIES

MODIFIED MOLDED BLOCK CARTRIDGES

t/PNJOBMNJDSPOSBUJOH t&YDFMMFOUEJSUIPMEJOHDBQBDJUZ t)JHIDIMPSJOFUBTUFPEPSBOECBEUBTUFPEPSSFEVDUJPO t&DPOPNJDDIPJDFGPSIJHITFEJNFOUBQQMJDBUJPOTMFBEJOHUPQSFNBUVSFQMVHHJOH

'*#3&%

:/&

™

0(:

CFB Series cartridges provide the effective chlorine taste & odor reduction found in traditional carbon block media while offering excellent sediment reduction capabilities.*

CFB Series products are a modified molded block created by use of our proprietary Fibredyne technology.

This technology creates a unique filter media by attaching powdered activated carbon onto a cellulosefree synthetic fiber matrix. The result is a single cartridge that combines the benefits of both a sediment filter and a carbon block into a single cartridge. Fibredyne's carbon block technology also offers up to two times the chlorine taste & odor reduction and dirt-holding capacity of traditional blocks.* In addition, this technology will not release fines into the effluent stream due to a unique post-filtration layer that is fused to the carbon/fiber media blend.

CFB Series cartridges are manufactured entirely from FDAcompliant materials, making them an ideal choice for a wide range of residential, food service, commercial and industrial applications.

* Based on manufacturer's internal testing.

CFB-10

CFB-20

CFB SERIES

.PEJmFE.PMEFE$BSCPO#MPDL$BSUSJEHFT

$'#

'MPX3BUFoHQN -QN

1BSUJDMF4J[F .JDSPOT

Tested and Certiﬁed by NSF International to NSF/ANSI

Standard 42 for material requirements only.

$BSUSJEHF4QFDJmDBUJPOTBOE1FSGPSNBODF%BUB

.PEFM

.BYJNVN

%JNFOTJPOT

.JDSPO3BUJOH

/PNJOBM

*OJUJBMå1 QTJ!

'MPX3BUF HQN

CFB-10

⁄

" x 9

⁄

(73mm x 248mm)

3.0 psi @ 1 gpm

(0.7 bar @ 3.8 Lpm)

CFB-20

2 7 ⁄

" x 20"

(73mm x 508mm)

3.0 psi @ 2 gpm

(0.7 bar @ 7.6 Lpm)

3.0 psi @ 3 gpm

(0.7 bar @ 11.4 Lpm)

CFB-30

2 7 ⁄

" x 30"

(73mm x 762mm)

#BTFEPONBOVGBDUVSFShTJOUFSOBMUFTUJOH

.BUFSJBMTPG$POTUSVDUJPO

Filter Media

End Caps

Netting

Gaskets

Bonded PAC

Polypropylene

Polyethylene

Santoprene ™

$IMPSJOF5BTUF0EPS

3FEVDUJPO!'MPX3BUF HQN

>5,000 gallons @ 1 gpm

(>18,900 L @ 3.8 Lpm)

>10,000 gallons @ 2 gpm

(>37,800 L @ 7.6 Lpm)

>15,000 gallons @ 3 gpm

(>56,700 L @ 11.4 Lpm)

WARNING: Do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the unit.

NOTE: Performance capacity depends on system design, flow rate and certain other application conditions. Certain states require system registration or certification for health-related contaminant reduction claims.

NOTE: Cartridges will contain a very small amount of carbon fines (very fine black powder). After installation, a new cartridge should be flushed with sufficient water to remove all traces of fines prior to using the water.

NOTE: Micron ratings based on 85% or greater removal of given particle size. Estimated capacity using 2ppm free available chlorine at 0.5 ppm breakthrough.

5FNQFSBUVSF

3BUJOH

40°F-180°F

(4.4°C-82.2°C)

40°F-180°F

(4.4°C-82.2°C)

40°F-180°F

(4.4°C-82.2°C)

*OEJBOB"WFOVFr10#PYr4IFCPZHBO8JTDPOTJO

$VTUPNFS4FSWJDFr'BYrTVQQPSUTQFDJBMJTU!QFOUFLàMUSBUJPODPN

*OUFSOBUJPOBMr'BYrJOUFSOBUJPOBM!QFOUFLàMUSBUJPODPN www.pentekfiltration.com Printed in USA JE06 310113

TECHnoLoG

™

y

CFB-PB10 LEAD REDuCTIon

MoDIFIED MoLDED BLoCK CARTRIDGE

• nominal 0.5-micron rating*

• 99.95% reduction of Cryptosporidium and Giardia cysts*

• Lead reduction through 2000 gallons*

• Premium dirt-holding capacity.*

• High chlorine taste & odor and bad taste and odor reduction*

The CFB-PB cartridge offers the benefits of effective chlorine taste

& odor, cyst and lead reduction found in traditional carbon block media while offering premium sediment filtration.*

The CFB-PB product is modified molded block manufactured using our proprietary Fibredyne technology. This technology creates a unique filter media by attaching powdered activated carbon and lead adsorbent material onto a cellulose-free synthetic fiber matrix.

This results in higher reduction efficiencies that resist plugging, afford the longest life, and feature the lowest pressure drop over the effective life of the cartridge of any available 0.5 micron filter cartridge.*

Fibredyne's carbon block technology also offers up to two times the chlorine taste & odor reduction and dirt-holding capacity of traditional blocks.* In addition, this technology will not release fines into the effluent stream due to a unique postfiltration layer that is fused to the carbon/fiber media blend.

CFB-PB10

The CFB-PB cartridge is manufactured entirely from FDAcompliant materials, making it an ideal choice for a wide range of residential, food service, commercial and industrial applications.

* Based on manufacturer's internal testing.

CFB-PB10 CARTRIDGE

Lead Reduction Modified Molded Block Cartridge

$'#1#

Tested and Certified by NSF International to NSF/ANSI

Standard 42 for material requirements only.

'MPX3BUFoHQN -QN

Cartridge Specifications and Performance Data

Model

Maximum

Dimensions

Micron Rating

(nominal)*

Initial ∆P (psi) @

Flow Rate (gpm)*

CFB-PB10

⁄

" x 9

⁄

(73mm x 248mm)

0.5

8.1 psi @ 1 gpm

(0.6 bar @ 3.8 Lpm)

• Cyst Reduction†*

• Lead & Mercury Reduction*

* Based on manufacturer's internal testing.

Materials of Construction

Filter Media

End Caps

Netting

Gaskets

Bonded PAC

Polypropylene

Polyethylene

Santoprene

™

Chlorine Taste & odor

Reduction @ Flow Rate (gpm)*

>5,000 gallons @ 1 gpm

(>18,900 L @ 3.8 Lpm)

WARNING: Do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the unit.

NOTE: Micron ratings based on 85% or greater removal of given particle size. Estimated capacity using 2ppm free available chlorine at 0.5 ppm breakthrough.

†NOTE: Giardia, Cryptosporidium, Entamoeba and Toxoplasma cyst claim based on tests showing greater than 99.95% reduction using NSF Standard 53 protocol.

Temperature

Rating

40°F-180°F

(4.4°C-82.2°C)

502 Indiana Avenue • P.O. Box 1047 • Sheboygan, Wisconsin 53082-1047

Customer Service: 800.645.0267 • Fax: 888.203.7361 • [email protected]

International: 920.457.9435 • Fax: 920.457.2417 • [email protected]

www.pentekfiltration.com Printed in USA JE06 310116

'*#3&%

:/&

™

0(:

CFB-PLUS SERIES

MODIFIED MOLDED BLOCK CARTRIDGES

t/PNJOBMNJDSPOSBUJOH t1SFNJVNEJSUIPMEJOHDBQBDJUZ t1SFNJVNDIMPSJOFUBTUFPEPSBOECBEUBTUFBOEPEPSSFEVDUJPO

CFB-Plus30

CFB-Plus 10BB

CFB-Plus

CFB-Plus 20BB

CFB-Plus 20

The CFB-Plus Series cartridges are an enhanced version of our CFB product. It offers the same benefits with even greater chlorine taste

& odor reduction and the highest sediment reduction found in a carbon cartridge.*

CFB-Plus Series products are modified molded blocks manufactured using our proprietary

Fibredyne technology. This technology creates a unique filter media by attaching powdered activated carbon onto a cellulosefree synthetic fiber matrix. The result is a single cartridge that combines the benefits of both a sediment filter and a carbon block into a single cartridge.

CFB-Plus Series cartridges are manufactured entirely from FDAcompliant materials, making them an ideal choice for a wide range of residential, food service, commercial and industrial applications.

* Based on manufacturer's internal testing.

CFB-PLUS SERIES

.PEJmFE.PMEFE$BSCPO#MPDL$BSUSJEHFT

$'#1MVT

$'#1MVT##

'MPX3BUFoHQN -QN 'MPX3BUFoHQN -QN

Tested and Certiﬁed by NSF International to NSF/ANSI

Standard 42 for material requirements only.

$BSUSJEHF4QFDJmDBUJPOTBOE1FSGPSNBODF%BUB

.PEFM

.BYJNVN

%JNFOTJPOT

.JDSPO3BUJOH

/PNJOBM

*OJUJBMå1 QTJ!

'MPX3BUF HQN

CFB-Plus10

2 7 ⁄

" x 9 3 ⁄

(73mm x 248mm)

5-10

1.6 psi @ 1 gpm

(0.7 bar @ 3.8 Lpm)

CFB-Plus20

⁄

" x 20"

(73mm x 508mm)

5-10

1.6 psi @ 2 gpm

(0.7 bar @ 7.6 Lpm)

CFB-Plus30

CFB-Plus10BB

⁄

" x 30"

(73mm x 762mm)

4 5 ⁄

" x 9 3 ⁄

(118mm x 248mm)

5-10

CFB-Plus20BB

4 5 ⁄

" x 20"

(118mm x 508mm)

5-10

#BTFEPONBOVGBDUVSFShTJOUFSOBMUFTUJOH

.BUFSJBMTPG$POTUSVDUJPO

Filter Media

End Caps

Netting

Gaskets

Bonded PAC

Polypropylene

Polyethylene

Santoprene ™

1.6 psi @ 3 gpm

(0.7 bar @ 11.4 Lpm)

2.5 psi @ 2 gpm

(0.2 bar @ 7.6 Lpm)

2.5 psi @ 4 gpm

(0.2 bar @ 11.4 Lpm)

$IMPSJOF5BTUF0EPS

3FEVDUJPO!'MPX3BUF HQN

>10,000 gallons @ 1 gpm

(>37,800 L @ 3.8 Lpm)

>20,000 gallons @ 2 gpm

(>75,700 L @ 7.6 Lpm)

>30,000 gallons @ 3 gpm

(>113,500 L @ 11.4 Lpm)

>25,000 gallons @ 2 gpm

(>94,600 L @ 7.6 Lpm)

>50,000 gallons @ 4 gpm

(>189,000 L @ 15.1 Lpm)

WARNING: Do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the unit.

NOTE: Micron ratings based on 85% or greater removal of given particle size. Estimated capacity using 2ppm free available chlorine at 0.5 ppm breakthrough.

5FNQFSBUVSF

3BUJOH

40°F-180°F

(4.4°C-82.2°C)

40°F-180°F

(4.4°C-82.2°C)

40°F-180°F

(4.4°C-82.2°C)

40°F-180°F

(4.4°C-82.2°C)

40°F-180°F

(4.4°C-82.2°C)

*OEJBOB"WFOVFr10#PYr4IFCPZHBO8JTDPOTJO

$VTUPNFS4FSWJDFr'BYrTVQQPSUTQFDJBMJTU!QFOUFLàMUSBUJPODPN

*OUFSOBUJPOBMr'BYrJOUFSOBUJPOBM!QFOUFLàMUSBUJPODPN www.pentekfiltration.com Printed in USA JE06 310114

CFBC SERIES

MODIFIED MOLDED BLOCK CARTRIDGES

t/PNJOBMNJDSPOSBUJOH tSFEVDUJPOPG$SZQUPTQPSJEJVNBOE(JBSEJB$ZTUT t1SFNJVNEJSUIPMEJOHDBQBDJUZ t)JHIDIMPSJOFUBTUFPEPSBOECBEUBTUFBOEPEPSSFEVDUJPO

'*#3&%

:/&

™

0(:

CFBC Series cartridges offer the effective chlorine taste and odor reduction found in traditional carbon block media while providing superior sediment reduction with resistance to premature plugging. They are highly effective at reducing chlorine taste

& odor, bad taste and odor, as well as some organic chemicals.*

CFBC Series products are modified molded blocks manufactured using our proprietary Fibredyne technology. This technology creates a unique filter media by attaching powdered activated carbon onto a cellulose-free synthetic fiber matrix.

The result is a single cartridge that combines the benefits of both a sediment filter and a carbon block into a single cartridge.

Benefits of this technology include low pressure drop over the entire life of the cartridge and up to three times the chlorine taste & odor and dirt-holding capacity of traditional

0.5 micron carbon blocks.* In addition, Fibredyne's technology will not release fines into the effluent stream due to a unique postfiltration layer that is fused to the carbon/fiber media blend.

CFBC Series cartridges are manufactured entirely from FDAcompliant materials, making them an ideal choice for a wide range of residential, food service, commercial and industrial applications.

* Based on manufacturer’s internal testing.

CFBC-10

CFBC-20

CFBC SERIES

.PEJmFE.PMEFE$BSCPO#MPDL$BSUSJEHFT

$'#$

'MPX3BUFoHQN -QN

Tested and Certiﬁed by NSF International to NSF/ANSI

Standard 42 for material requirements only.

$BSUSJEHF4QFDJmDBUJPOTBOE1FSGPSNBODF%BUB

.PEFM

.BYJNVN

%JNFOTJPOT

.JDSPO3BUJOH

/PNJOBM

*OJUJBMå1 QTJ!

'MPX3BUF HQN

CFBC-10

2 7 ⁄

" x 9 3 ⁄

(73mm x 248mm)

0.5

10.7 psi @ 1 gpm

(0.7 bar @ 3.8 Lpm)

CFBC-20

⁄

" x 20"

(73mm x 508mm)

0.5

#BTFEPONBOVGBDUVSFShTJOUFSOBMUFTUJOH

10.7 psi @ 2 gpm

(0.7 bar @ 7.6 Lpm)

.BUFSJBMTPG$POTUSVDUJPO

Filter Media

End Caps

Netting

Gaskets

Bonded PAC

Polypropylene

Polyethylene

Santoprene ™

$IMPSJOF5BTUF0EPS

3FEVDUJPO!'MPX3BUF HQN

>20,000 gallons @ 1 gpm

(>75,700 L @ 3.8 Lpm)

>40,000 gallons @ 2 gpm

(>75,700 L @ 3.8 Lpm)

WARNING: Do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the unit.

NOTE: Micron ratings based on 85% or greater removal of given particle size. Estimated capacity using 2ppm free available chlorine at 0.5 ppm breakthrough.

NOTE: Giardia, Cryptosporidium, Entamoeba and Toxoplasma cyst claim based on tests showing greater than 99.95% reduction using NSF Standard 53 protocol.

5FNQFSBUVSF

3BUJOH

40°F-180°F

(4.4°C-82.2°C)

40°F-180°F

(4.4°C-82.2°C)

*OEJBOB"WFOVFr10#PYr4IFCPZHBO8JTDPOTJO

$VTUPNFS4FSWJDFr'BYrTVQQPSUTQFDJBMJTU!QFOUFLàMUSBUJPODPN

*OUFSOBUJPOBMr'BYrJOUFSOBUJPOBM!QFOUFLàMUSBUJPODPN www.pentekfiltration.com Printed in USA JE06 310112

ChlorPlus 20

ChlorPlus BB

CHLORAMINE REDUCTION CARBON CARTRIDGES

t4VQFSJPSDIMPSBNJOFBOEDIMPSJOFSFEVDUJPO t$3'$##3BEJBM'MPX t$IMPS1MVT

4FSJFT$BSCPO#SJRVFUUF

CRFC20-BB

PENTEK ® offers multiple product solutions for chloramine reduction.

Chloramine is increasingly becoming more common as an alternative to chlorine for water treatment.

The

ChlorPlus ®

carbon block cartridges help reduce sediment while providing greater chloramine performance capacities than granular carbon. They also significantly reduce the carbon fines found in many granular canisters.

The

CRFC20-BB

heavy duty radial flow cartridge measures 4

⁄

inches in diameter and 20 inches long, which is ideal for higher flow rate and capacity applications. This cartridge incorporates a 70–micron porous polypropylene outer shell and a spun polypropylene-wrapped core. The bed of granular activated carbon (GAC) between the outer shell and core creates a unique radial flow design which effectively removes chloramine, has a low pressure drop, and helps to reduce fines commonly seen in GAC-style cartridges.

All of these cartridges utilize advanced activated carbon technology which allows superior chloramine and chlorine reduction.

The range of sizes and capacities offered by PENTEK chloramine reduction cartridges makes them ideal for both point-of-entry (POE) and point-of-use (POU) applications.

CHLORAMINE REDUCTION CARBON CARTRIDGES

60 0.7

ChlorPlus 10

ChlorPlus 20

ChlorPlus 10BB

ChlorPlus 20BB

CRFC-BB

CRFC20-BB

0.6

0.5

0.4

30 0.3

0.2

0.1

2000 4000 6000

ChlorPlus 10 - 0.5 gpm

ChlorPlus 20 - 1 gpm

ChlorPlus 10BB - 2 gpm

ChlorPlus 20BB - 4 gpm

8000 10000 12000

-0.0

-0.1

0 2 4 6

Flow Rate (gpm)

8 10 12

Volume (gallons)

$BSUSJEHF4QFDJmDBUJPOTBOE1FSGPSNBODF%BUB

.PEFM

.BYJNVN

%JNFOTJPOT

.JDSPO

3BUJOH

OPNJOBM

*OJUJBMå1 QTJ

!'MPX3BUF HQN

ChlorPlus 10

2 7 ⁄

" x 9¾"

(73 mm x 248 mm)

6 psi @ 1.0 gpm

(0.41 bar @ 3.8 Lpm)

ChlorPlus 20

ChlorPlus 10BB

ChlorPlus 20BB

2 7 ⁄

" x 20"

(73 mm x 508 mm)

4 1 ⁄

" x 9¾"

(114.3 mm x 248 mm)

⁄

" x 20"

(114.3 mm x 508 mm)

6 psi @ 2 gpm

(0.41 bar @ 7.6 Lpm)

6 psi @ 2.0 gpm

(0.41 bar @ 7.6 Lpm)

6 psi @ 4.0 gpm

(0.41 bar @ 15.2 Lpm)

CRFC-BB

CRFC20-BB

4 1 ⁄

" x 9¾"

(114 mm x 248 mm)

4½" x 20"

(114 mm x 508 mm)

2.5 psi @ 2.5 gpm

(0.17 bar @ 9.5 Lpm)

<1 psi @ 1.5 gpm

(<0.07 bar @ 5.7 Lpm)

2.5 psi @ 5 gpm

(.17 bar @ 18.9 Lpm)

<1 psi @ 2.5 gpm

(<.07 bar @ 9.5 Lpm)

#BTFEPONBOVGBDUVSFS}TJOUFSOBMUFTUJOH

.BUFSJBMTPG$POTUSVDUJPO

1BSU $IMPS1MVT

Filter Media

Endcaps

Inner Wrap/Core

Outer Wrap/Shell

Expansion Pad

Post Filter

Netting

Gasket

Temperature Rating

Advanced Bonded PAC

Polypropylene

Polyolefin

N/A

Polyethylene

4BOUPQSFOF

40–125ºF (4.4–51.7ºC)

$IMPSJOF5BTUF0EPSp

3FEVDUJPO!'MPX3BUF

>50,000 gallons @ 1 gpm

(>189,270L @ 3.8 Lpm)

>100,000 gallons @ 2 gpm

(>378,451L @ 7.6 Lpm)

>250,000 gallons @ 2 gpm

(>946,352L @ 7.6 Lpm)

>500,000 gallons @ 4 gpm

(>1,892,706L @ 15.2 Lpm)

>100,000 gallons @ 2 gpm

(>378,451L @ 7.6 Lpm)

>200,000 gallons @ 4 gpm

(>757,082L @ 15.2 Lpm)

$3'$##$3'$##

Advanced Granular Activated

Carbon

Polypropylene

4QVO1PMZQSPQZMFOF

Polyethylene

N/A

4QVO1PMZQSPQZMFOF

N/A

4BOUPQSFOF

40–125ºF (4.4–51.7ºC)

$IMPSBNJOF3FEVDUJPOp

!'MPX3BUF HQN

2,500 gallons @ 0.5 gpm (9,463L @ 1.9 L/min)

1,000 gallons @ 1.0 gpm (3,785L @ 3.8 L/min)

5,000 gallons @ 1.0 gpm (18,927L @ 3.8 L/min)

2,000 gallons @ 2.0 gpm (7,570L @ 7.6 L/min)

3,500 gallons @ 2.0 gpm (13,249L @ 7.6 L/min)

7,000 gallons @ 4.0 gpm (26,498L @ 15.2 L/min)

12,000 gallons @ 1.5 gpm (45,424L @ 5.7 L/min)

5,000 gallons @ 2.5 gpm (18,927L @ 9.5 L/min)

25,000 gallons @ 2.5 gpm (94,635L @ 9.5 L/min)

10,000 gallons @ 5.0 gpm (37,854L @ 18.9 L/min)

WARNING:

For drinking water applications, do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the system.

NOTE:

4PNFIBSNMFTTCBDUFSJBXJMMBUUBDL cellulose media cartridges. If your cartridge seems to disintegrate, or has a musty or moldy odor, switch to a synthetic media cartridge or consult the manufacturer.

†NOTE:

Estimated capacity tested at given flow rate using 2 ppm free available chlorine to

0.5 ppm breakthrough and 3 ppm chloramine to

0.5 ppm breakthrough.

NOTE:

Increased flow rates may result in less effective chlorine reduction.

*OEJBOB"WFOVFr10#PYr4IFCPZHBO8JTDPOTJO

$VTUPNFS4FSWJDFr'BYrTVQQPSUTQFDJBMJTU!QFOUFLàMUSBUJPODPN

¥1FOUBJS3FTJEFOUJBM'JMUSBUJPO--$

*OUFSOBUJPOBMr'BYrJOUFSOBUJPOBM!QFOUFLàMUSBUJPODPN

XXXQFOUFLàMUSBUJPODPN 1SJOUFEJO64"0$

COCONUT BASED CARBON BLOCK CARTRIDGES

t8BUFSXBTIFEDPDPOVUDBSCPOGPSNVMBUJPO t1SFNJVNIJHIDBQBDJUZCBEUBTUFPEPSBOEDIMPSJOFUBTUFPEPSSFEVDUJPO t&OIBODFEEJSUIPMEJOHDBQBDJUZ

CEP-10E

CCBC-10

Coconut based carbon block cartridges are highly effective at reducing unwanted taste & odor and chlorine taste & odor from potable drinking water, and they are equally effective at reducing fine sediment.*

Coconut based carbon block cartridges are manufactured using a patented process and are made from a water-washed, coconut-carbon formulation. This process and media yield a cartridge with high chlorine taste & odor reduction capacity.

These cartridges are protected by

Endurawrap

, a uniquely formulated polyolefin bilaminate pre-filter, designed to significantly increase the useful life of the cartridge by trapping sediment that typically plugs carbon block cartridges.

They are an ideal choice for a wide range of residential, food service, commercial and industrial applications. They also make excellent polishing filters or prefilters in applications requiring fine filtration and high capacity.

* Based on manufacturer’s internal testing.

COCONUT CARBON

$PDPOVU#BTFE$BSCPO#MPDL$BSUSJEHFT

$$#$

$&1

$$#$

$&1

1BSUJDMF4J[F .JDSPOT

'MPX3BUFoHQN -QN

$BSUSJEHF4QFDJmDBUJPOTBOE1FSGPSNBODF%BUB

.PEFM

.BYJNVN%JNFOTJPOT

.JDSPO3BUJOH

OPNJOBM

CCBC-10 2 7 ⁄

" x 9 3 ⁄

" (73 mm x 248 mm) 1

*OJUJBMå1 QTJ

!'MPX3BUF HQN

3.3 psi @ 1 gpm (0.23 bar @ 3.8 Lpm)

CEP-10E 2

⁄

" x 9

⁄

" (73 mm x 248 mm) 5 3.0 psi @ 1 gpm (0.2 bar @ 3.8 Lpm)

#BTFEPONBOVGBDUVSFShTJOUFSOBMUFTUJOH

.BUFSJBMTPG$POTUSVDUJPO

Filter Media

End Caps

Inner/Outer Wraps

Netting

Gaskets

Temperature Rating

Water-Washed Coconut Based Carbon (CCBC-10)

Acid-Washed Coconut Based Carbon (CEP-10E)

Polypropylene

Polyolefin

Polyethylene

Buna-N

40–125ºF (4.4–51.7ºC)

WARNING:

Do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the system.

U.S. Patent No. 5,976,432 & 5,823,668

$IMPSJOF5BTUF0EPS

3FEVDUJPO!'MPX3BUF

>20,000 gallons @ 1 gpm

(75,700L @ 3.8 Lpm)

>5,000 gallons @ 1 gpm

(18,900L @ 3.8 Lpm)

Tested and Certiﬁed by NSF International to NSF/ANSI Standard 42 for material requirements only.

*OEJBOB"WFOVFr10#PYr4IFCPZHBO8JTDPOTJO

$VTUPNFS4FSWJDFr'BYrTVQQPSUTQFDJBMJTU!QFOUFLàMUSBUJPODPN

*OUFSOBUJPOBMr'BYrJOUFSOBUJPOBM!QFOUFLàMUSBUJPODPN www.pentekfiltration.com Printed in USA MR06 310079

EP sEriEs CarBON-BriQUEttE CartridgEs

• Nominal 5-micron rating*

• High dirt-holding capacity maximizes utilization of the carbon block*

• Highly effective bad taste & odor and chlorine taste & odor reduction*

EP-20

EP-10

EP-BB

EP-

20BB

EP Series carbon briquette cartridges are manufactured using a patented process that yields a cartridge with a nominal 5-micron filtration rating, high dirt-holding capacity. A high porosity design helps prevent the cartridge from plugging before its adsorption capacity is exhausted, maximizing the utilization of the carbon while maintaining low pressure drop.

These cartridges are protected by

Endurawrap

, a uniquely formulated polyolefin bilaminate pre-filter, designed to significantly increase the useful life of the cartridge by trapping sediment that typically plugs carbon block cartridges.

EP Series cartridges are manufactured entirely from FDAcompliant materials making them an ideal choice for a wide range of residential, food service, commercial and industrial applications.

* Based on manufacturer’s internal testing.

EP sEriEs

Carbon-Briquette Cartridges

&14&3*&4$"353*%(&4

1BSUJDMF4J[F .JDSPOT

'MPX3BUFoHQN -QN

Cartridge specifications and Performance data

Model Maximum dimensions

Micron rating*

(nominal)

EP-10 2

⁄

" x 9

⁄

" (73 mm x 248 mm) 5

⁄

" x 20" (73 mm x 508 mm) EP-20

EP-30

initial ∆P (psi)

@ Flow rate (gpm)

3.4 psi @ 1 gpm (0.23 bar @ 3.8 Lpm)

3.4 psi @ 2 gpm (0.23 bar @ 7.6 Lpm)

Chlorine taste & Odor reduction @ Flow rate

>6000 gallons @ 1 gpm

(22,700L @ 3.8 Lpm)

>12,000 gallons @ 2 gpm

(45,400L @ 7.6 Lpm)

EP-40 5

EP-BB

EP20-BB

⁄

" x 9

⁄

" (118 mm x 248 mm)

⁄

" x 20" (118 mm x 508 mm)

4.3 psi @ 2 gpm (0.30 bar @ 7.6 Lpm)

5.5 psi @ 5 gpm (0.38 bar @ 19 Lpm)

>22,000 gallons @ 2 gpm

(83,300L @ 7.6 Lpm)

>40,000 gallons @ 4 gpm

(151,400L @ 15.1 Lpm)

* Based on manufacturer's internal testing

Materials of Construction

Filter Media

End Caps

Inner/Outer Wraps

Netting

Bonded PAC

Polypropylene

Polyolefin

Polyethylene

This EP-10, EP-20, EP-BB and EP-20BB are

Tested and Certified by NSF International to NSF/ANSI Standard 42 for material requirements only.

Gaskets

Temperature Rating

Buna-N

40–180ºF (4.4–82.2ºC)

WARNING:

Do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the system.

NOTE:

The EP cartridges will contain a very small amount of carbon fines (very fine black powder) and a new cartridge after installation should be flushed with sufficient water to remove the fines from your water system before using the water.

NOTE:

Micron ratings based on 85% or greater removal of given particle size. Data obtained from actual particle counts using AC Fine Test Dust and Latex spheres.

NOTE:

Estimated capacity using 2ppm free available chlorine (FAC) at continuous flow with greater than 90% reduction.

U.S. Patent No. 5,976,432 & 5,823,668

502 Indiana Avenue • P.O. Box 1047 • Sheboygan, Wisconsin 53082-1047

Customer Service: 800.645.0267 • Fax: 888.203.7361 • [email protected]

International: 920.457.9435 • Fax: 920.457.2417 • [email protected]

www.pentekfiltration.com Printed in USA MR06 310077

ELPC-30

'*#3&%

:/&

™

0(:

ELPC SERIES

ELECTROPLATING CARBON CARTRIDGES

t$FMMVMPTFGSFFDPOTUSVDUJPO t3FTJTUBOUUPDIFNJDBMCSFBLEPXOJOCPUIBDJEJDBOEBMLBMJOFTPMVUJPOTVQUP' $ t8JMMOPUDPOUSJCVUFUPQMBUJOHQPSPTJUZPSCSJUUMFOFTT t*OUFHSBUFEQPTUmMUSBUJPOMBZFSUPFOTVSFUIBUOPDBSCPOmOFTBSFCMFEJOUPUIFQMBUJOHCBUI t&OEDBQHBTLFUTBSFQFSNBOFOUMZNPMEFEPOUPUIFFOEDBQTUPFBTFmMUFSDBSUSJEHFDIBOHFPVU

HBTLFUTDBOOPUGBMMPGGJOUPUIFmMUFSIPVTJOHEVSJOHJOTUBMMBUJPOPSSFNPWBMPGmMUFS

The ELPC Series is a premium line of activated carbon filter cartridges specifically designed for electroplating solutions. They represent the best technology available in cartridge filtration for use in a wide range of electroplating applications.

The unique technology used to manufacture this product ensures that there is no bleeding of carbon fines into the plating bath. In addition, the carbon that is used is an ultra-clean, highly purified carbon to ensure that sulfur is not leached into the plating bath.

ELPC Series products have a

10-micron nominal rating with superior dirt-holding ability.

The fibrous physical structure created by our proprietary

Fibredyne technology produces a unique block with true depth filtration capability which allows for maximum treatment with minimal pressure drop through the cartridge.

ELPC-10

ELPC-20

ELPC SERIES

&MFDUSPQMBUJOH$BSCPO$BSUSJEHFT

&-1$

'MPX3BUFoHQN -QN

1BSUJDMF4J[F .JDSPOT

$BSUSJEHF4QFDJmDBUJPOTBOE1FSGPSNBODF%BUB

.PEFM

.BYJNVN%JNFOTJPOT

.JDSPO3BUJOH

/PNJOBM

ELPC-10

⁄

" x 10"*

(73mm x 248mm)

*OJUJBMå1 QTJ!'MPX3BUF HQN

ELPC-20

2 7 ⁄

" x 20"

(73mm x 508mm)

3.4 psi @ 1 gpm

(0.2 bar @ 3.8 Lpm)

3.4 psi @ 2 gpm

(0.2 bar @ 7.6 Lpm)

ELPC-30

2 7 ⁄

" x 30"

(73mm x 762mm)

3.4 psi @ 3 gpm

(0.2 bar @ 11.4 Lpm)

*Designed for use in spring-loaded industrial housings. This will not fit a standard PENTEK ® plastic 10-inch housing.

.BUFSJBMTPG$POTUSVDUJPO

Filter Media

End Caps

Netting

Gaskets

Bonded PAC

Polypropylene

Polyethylene

Santoprene ™

WARNING: Do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the unit.

NOTE: Micron ratings based on 85% or greater removal of given particle size. Estimated capacity using 2ppm free available chlorine at 0.5 ppm breakthrough.

5FNQFSBUVSF

3BUJOH

40°F-180°F

(4.4°C-82.2°C)

40°F-180°F

(4.4°C-82.2°C)

40°F-180°F

(4.4°C-82.2°C)

*OEJBOB"WFOVFr10#PYr4IFCPZHBO8JTDPOTJO

$VTUPNFS4FSWJDFr'BYrTVQQPSUTQFDJBMJTU!QFOUFLàMUSBUJPODPN

*OUFSOBUJPOBMr'BYrJOUFSOBUJPOBM!QFOUFLàMUSBUJPODPN www.pentekfiltration.com Printed in USA 310115 JL08

epm series mOdiFied epsiLON

CarBON-BriQUette Cartridges

• Nominal 10-micron rating*

• enhanced dirt holding capacity for extended cartridge life*

• Bad taste & odor and chlorine taste & odor reduction*

• Lowest pressure drop

• economically priced

EPM Series cartridges are a modified version of our EP Series cartridge.

An economical price makes this cartridge suitable for taste, odor and chlorine taste & odor reduction, as well as sediment filtration.*

EPM Series cartridges are manufactured using a patented process that yields a cartridge with a nominal 10-micron filtration rating, high porosity and chlorine taste & odor reduction. The high porosity design helps prevent the cartridge from plugging before its adsorption capability is exhausted, maximizing the utilization of the carbon while maintaining low pressure drop.

These cartridges are protected by

Endurawrap

, a uniquely formulated polyolefin bilaminate pre-filter, designed to significantly increase the useful life of the cartridge by trapping sediment that typically plugs carbon block cartridges.

EPM Series cartridges are manufactured entirely from FDAcompliant materials making them an ideal choice for a wide range of residential, food service, commercial and industrial applications.

* Based on manufacturer’s internal testing.

EPM-20

EPM-10

EPM-BB

EPM-

20BB

epm series

modified epsilon Carbon-Briquette Cartridges

&1.

&1.##

&1.

&1.##

&1.

1BSUJDMF4J[F .JDSPOT

'MPX3BUFoHQN -QN

NOTE:

Micron ratings based on 85% or greater removal of given particle size. Data obtained from actual particle counts, using AC Fine Test Dust at 1 gpm. Estimated capacity using 2.0 ppm free available chlorine (FAC) at 0.5 ppm break through.

Cartridge specifications and performance data model

EPM-10

EPM-20

EPM-BB

EPM-20BB

maximum dimensions

⁄

" x 9

⁄

" (73 mm x 248 mm)

⁄

" x 20" (73 mm x 508 mm)

⁄

" x 9

⁄

" (118 mm x 248 mm)

⁄

" x 20" (118 mm x 508 mm)

micron rating*

(nominal)

initial ∆p (psi)

@ Flow rate (gpm)

1.5 psi @ 1 gpm (0.10 bar @ 3.8 Lpm)

1.0 psi @ 2 gpm (0.07 bar @ 7.6 Lpm)

5.0 psi @ 2 gpm (0.35 bar @ 7.6 Lpm)

4.0 psi @ 4 gpm (0.28 bar @ 15.1 Lpm)

Chlorine taste & Odor reduction @ Flow rate

>3,000 gallons @ 1 gpm

(11,400L @ 3.8 Lpm)

>6,000 gallons @ 2 gpm

(22,700L @ 7.6 Lpm)

>15,000 gallons @ 2 gpm

(56,750L @ 7.6 Lpm)

>30,000 gallons @ 4 gpm

(113,500L @ 15.1 Lpm)

* Based on manufacturer's internal testing materials of Construction

Filter Media

End Caps

Bonded PAC

Polypropylene

Tested and Certified by NSF International to NSF/ANSI Standard 42 for material requirements only.

Outer Wrap

Netting

Gaskets

Temperature Rating

Polyolefin

Polyethylene

Buna-N

40–180ºF (4.4–82.2ºC)

NOTE:

Performance capacity depends on system design, flow rate and certain other application conditions.

NOTE:

When greater chlorine taste & odor reduction is needed, use the standard EP series blocks.

WARNING:

Do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the system.

NOTE:

EPM-Series cartridges will contain a very small amount of carbon fines (very fine black powder). After installation follow the instructions for flushing the cartridge to remove the fines before using the water. You should run (flush) the tap at least 20 seconds prior to using water for drinking or cooking purposes. This is particularly important if the tap has not been used daily.

U.S. Patent No. 5,976,432 & 5,823,668

502 Indiana Avenue • P.O. Box 1047 • Sheboygan, Wisconsin 53082-1047

Customer Service: 800.645.0267 • Fax: 888.203.7361 • [email protected]

International: 920.457.9435 • Fax: 920.457.2417 • [email protected]

www.pentekfiltration.com Printed in USA MR06 310076

GAC-20BB

GAC SERIES GRANULAR ACTIVATED

CARBON CARTRIDGES

t&GGFDUJWFCBEUBTUFPEPSBOEDIMPSJOFUBTUFPEPSSFEVDUJPO t%FTJHOFEGPSPQUJNBMBETPSQUJPO t1PTUmMUFSUPSFEVDFDBSCPOmOFT t"WBJMBCMFJOBWBSJFUZPGTJ[FTBOEnPXSBUFT

GAC Series cartridges effectively reduce unwanted tastes and odors, including chlorine taste & odor from your drinking water.* They are designed to allow maximum contact between the water and carbon, ensuring optimal adsorption.

The construction of the cartridge allows water to enter at one end and pass through the entire length of the carbon bed before exiting the other end of the cartridge, while an internal expansion pad minimizes channeling or bypass.

Before the water exits the cartridge, a 20-micron post filter helps reduce carbon fines and other suspended particles from the filtered water. The post-filter is permanently fastened to an innovative support basket ensuring that it is firmly secured and eliminating any potential for bypass.

GAC Series cartridges are available in a variety of sizes and flow rates, and effectively provide good general-purpose drinking water filtration.

* Based on manufacturer’s internal testing.

GAC-20

GAC-5 GAC-BB

GAC SERIES

(SBOVMBS"DUJWBUFE$BSCPO$BSUSJEHFT

(1.9)

C-20

C-1

C-5

GAC-BB

C-20BB

(7.6) (15.1)

6.0

(22.7)

8.0

(30.3)

Flow Rate – gpm (Lpm)

10.0

(37.9)

$BSUSJEHF4QFDJmDBUJPOTBOE1FSGPSNBODF%BUB

.PEFM

.BYJNVN%JNFOTJPOT

GAC-5

GAC-10

GAC-20

GAC-BB

GAC-20BB

⁄

" x 4

⁄

" (73 mm x 124 mm)

2 7 ⁄

" x 9 3 ⁄

" (73 mm x 248 mm)

2 7 ⁄

" x 20" (73 mm x 508 mm)

⁄

" x 9

⁄

" (114 mm x 248 mm)

4 1 ⁄

" x 20" (114 mm x 508 mm)

#BTFEPONBOVGBDUVSFShTJOUFSOBMUFTUJOH

*OJUJBMå1 QTJ

!'MPX3BUF HQN

3.0 psi @ 0.5 gpm (0.2 bar @ 1.9 Lpm)

7.0 psi @ 1.0 gpm (0.5 bar @ 3.8 Lpm)

16 psi @ 2.0 gpm (1.1 bar @ 7.6 Lpm)

4.0 psi @ 2.0 gpm (0.3 bar @ 7.6 Lpm)

10.0 psi @ 4.0 gpm (0.7 bar @ 15 Lpm)

$IMPSJOF5BTUF0EPS

3FEVDUJPO!'MPX3BUF

250 gallons @ 0.5 gpm (900L @ 1.9 Lpm)

5,000 gallons @ 1.0 gpm (18,900L @ 3.8 Lpm)

10,000 gallons @ 2.0 gpm (37,800L @ 7.6 Lpm)

12,500 gallons @ 2.0 gpm (47,000L @ 7.6 Lpm)

25,000 gallons @ 4.0 gpm (95,000L @ 15 Lpm)

.BUFSJBMTPG$POTUSVDUJPO

Filter Media

End Caps

Post-Filter

Outer Casing

Expansion Pad

Granular Activated Carbon

Polystyrene

Spun Polypropylene

Polystyrene

Polypropylene

The GAC-10 and GAC-20BB are Tested and Certiﬁed by NSF International to

NSF/ANSI Standard 42 for material requirements only.

Gasket

Buna-N (top)

Santoprene (bottom)

Temperature Rating

40–125ºF (4.4–51.7ºC)

WARNING:

Do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the system.

NOTE:

A drinking water cartridge may contain carbon fines (very fine black powder). After installation and before using the water, follow the instructions for flushing the cartridge to remove fines.

NOTE:

It is recommended that you flush for 20 seconds prior to using the water for drinking or cooking purposes.

NOTE:

Chlorine Reduction is estimated capacity using 2ppm free available chlorine (FAC) at continuous flow with greater than 75% reduction.

*OEJBOB"WFOVFr10#PYr4IFCPZHBO8JTDPOTJO

$VTUPNFS4FSWJDFr'BYrTVQQPSUTQFDJBMJTU!QFOUFLàMUSBUJPODPN

*OUFSOBUJPOBMr'BYrJOUFSOBUJPOBM!QFOUFLàMUSBUJPODPN www.pentekfiltration.com Printed in USA JE07 310070

Floplus-20

Floplus-20BB

Floplus

™

Series

Modified Molded carbon Block cartridges

FloPlus™ cartridges utilize a revolutionary new technology that significantly enhances the traditional

Fibredyne product, making it possible to obtain cyst reduction in a cartridge that functions like a nominal

10-micron cartridge.

This product boasts extremely low pressure drops and high flow rates – comparable to 10-micron (very open) carbon cartridges. Its efficiency is so high that a

0.5-micron rating is possible, which means that cysts and very small particles can be removed to create cleaner, safer water.

This product is ideal for applications where pressure drop and low flow have been chronic problems in the past, as well as whole house water treatment with the addition of cyst reduction. However, it will address the needs of any end user looking for a product that offers high flow, low pressure drop, infrequent cartridge changes and cyst-free water.

Floplus-10BB Floplus-10

FEATURES

• Nominal 0.5-micron rating

• 99.95% reduction of Cryptosporidium and Giardia cysts

• Premium dirt-holding capacity

• Outstanding chlorine taste & odor reduction

• True depth filtration which offers greatest life of any cyst-capable

carbon cartridge

BENEFITS

• High flow rates and low pressure drop similar to a nominal

10-micron cartridge

• Delivers optimal cyst reduction for whole house carbon treatment

• Maximum life — dirt-holding ability of a 10-micron carbon block

with the particulate efficiency of a 0.5-micron cartridge

ApplIcATIoNS

• Whole house cyst reduction with carbon treatment

• Cyst reduction where low flow, high pressure drop or premature

plugging has been problematic

• Areas where low water pressure has made cyst reduction

difficult due to high pressure drops (low flow)

• High flow applications (>25 gpm possible)

Floplus™ Modified Molded carbon Block cartridges

20 20

FloPlus

FloPlus 20BB FloPlus 20

5 5

FloPlus™ Cyst Reduction

Carbon Block (NEW!)

Standard Cyst Reduction

Carbon Block

0 2.0

4.0

6.0

Flow Rate – gpm

8.0

10.0

cartridge Specifications and performance Data

Model

Maximum

Dimensions

Micron Rating

(Nominal)*

FloPlus-10

⁄

" x 9

⁄

(73mm x 248mm)

0.5

FloPlus-20

FloPlus-10BB

FloPlus-20BB

⁄

" x 20"

(73mm x 508mm)

⁄

" x 9

⁄

(118mm x 248mm)

⁄

" x 20"

(118mm x 508mm)

0.5

1 gpm 2 gpm

Gallons Per Minute – gpm

Initial ∆p (psi) @

Flow Rate (gpm)*

2 psi @ 1 gpm

(0.1 bar @ 3.8 Lpm)

2 psi @ 2 gpm

(0.1 bar @ 7.6 Lpm)

4 psi @ 2 gpm

(0.3 bar @ 7.6 Lpm)

4 psi @ 4 gpm

(0.3 bar @ 15.2 Lpm)

chlorine Taste & odor Reduction

@ Flow Rate (gpm)*

>10,000 gallons @ 1 gpm

(>37,800 L @ 3.8 Lpm)

>20,000 gallons @ 2 gpm

(>75,700 L @ 7.6 Lpm)

>25,000 gallons @ 2 gpm

(>94,500 L @ 7.6 Lpm)

>50,000 gallons @ 4 gpm

(>189,000 L @ 15.2 Lpm)

Materials of construction

Filter Media

End Caps

Netting

Gaskets

Temperature Rating

Bonded PAC

Polypropylene

Polyethylene

Santoprene

™

40°F to 180°F (4.4°C to 82.2°C) note: Performance capacity depends on system design, flow rate and certain other application conditions. Certain states require system registration or certification for health-related reduction claims.

Warning:

For drinking water applications, do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the system.

note: A drinking water cartridge may contain carbon fines (very fine black powder). After installation and before using the water, follow the instructions for flushing the cartridge to remove fines.

note: It is recommended that you run the tap for 20 seconds prior to using the water for drinking or cooking purposes.

The FPS-10 with the FloPlus 10, FPS-20 with the

FloPlus 20, FPS-10BB with the FloPlus 10BB and the FPS-20BB with the FloPlus 20BB are Tested and Certified by NSF International to NSF/ANSI

Standard 53 for the reduction of Cysts.

502 Indiana Avenue • P.O. Box 1047

Sheboygan, Wisconsin 53082-1047

Phone: 800.645.0267 • 920.457.9435

Fax: 888.203.7361 • 920.457.2417 www.pentekfiltration.com

NCP SERIES NON-CELLULOSE

CARBON-IMPREGNATED PLEATED CARTRIDGES

t/PODFMMVMPTFNFEJBSFTJTUTCBDUFSJBMBUUBDL t1SPWJEFTTFEJNFOUmMUSBUJPOBOEDIMPSJOFUBTUFPEPSSFEVDUJPO t1MFBUFEGPSNBYJNVNEJSUMPBEJOHDBQBDJUZ t/PNJOBMNJDSPOSBUJOH

NCP-20

NCP-10 NCP-BB

NCP-

20BB

NCP Series cartridges are constructed from a carbon- impregnated non-cellulose media.

They offer sediment-filtration, as well as taste, odor and chlorine taste and odor reduction in one cartridge.

Unlike cellulose cartridges, NCP

Series cartridges are resistant to bacterial attack allowing them to be used for municipal and nonchlorinated water applications.

Pleats provide additional surface area for high dirt-loading capacity, while maintaining minimal pressure drop. This combination of a pleated polyester media and carbon filtration produces an outstanding filter cartridge with extended service life.

NCP Series cartridges are excellent polishing filters, closed loop streams and are ideal for post reverse osmosis and well water applications.

NCP SERIES

**/PO$FMMVMPTF$BSCPO*NQSFHOBUFE1MFBUFE$BSUSJEHFT**

"--/$14&3*&4$"353*%(&4

/$1

NCP-20

/$1

NCP-10 NCP-BB

NCP-

20BB

/$1##

1BSUJDMF4J[F .JDSPOT

'MPX3BUFoHQN -QN

$BSUSJEHF4QFDJmDBUJPOTBOE1FSGPSNBODF%BUB

.PEFM

NCP-10

NCP-BB

NCP-20

NCP-20BB

1 ⁄

⁄

.BYJNVN%JNFOTJPOT

" x 9

⁄

" x 9 3 ⁄

⁄

" (64 mm x 248 mm)

" (114 mm x 248 mm)

" x 20" (64 mm x 508 mm)

" x 20" (114 mm x 508 mm)

.JDSPO

3BUJOH

OPNJOBM

*OJUJBMå1 QTJ

!'MPX3BUF HQN

2 psi @ 3 gpm (0.1 bar @ 11 Lpm)

2 psi @ 8 gpm (0.1 bar @ 30 Lpm)

2 psi @ 5 gpm (0.1 bar @ 19 Lpm)

1 psi @ 10 gpm (<0.1 bar @ 38 Lpm)

$IMPSJOF5BTUF0EPS

3FEVDUJPO!'MPX3BUF

225 gallons @ 1 gpm

(850L @ 3.8 Lpm)

500 gallons @ 2 gpm

(1890L @ 7.6 Lpm)

450 gallons @ 2 gpm

(1700L @ 7.6 Lpm)

1000 gallons @ 4 gpm

(3780L @ 15 Lpm)

'JMUSBUJPOFGmDJFODZBOEDIMPSJOFUBTUFBOEPEPSSFEVDUJPOFGmDJFODZBSFSFEVDFEBUIJHIFSnPXSBUFT$IMPSJOFUBTUFBOEPEPSSFEVDUJPO

CBTFEPOHSFBUFSUIBOSFEVDUJPOVTJOHQQNGSFFDIMPSJOFGFFEDPODFOUSBUJPOBU' $BUDPOUJOVPVTnPX

.BUFSJBMTPG$POTUSVDUJPO

Filter Media

End Caps

Pleated Carbon-Impregnated Polyester

Vinyl Plastisol

Netting

Core

Polypropylene

Temperature Rating

40–125ºF (4.4–51.7ºC)

WARNING:

Do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the system.

*OEJBOB"WFOVFr10#PYr4IFCPZHBO8JTDPOTJO

$VTUPNFS4FSWJDFr'BYrTVQQPSUTQFDJBMJTU!QFOUFLàMUSBUJPODPN

*OUFSOBUJPOBMr'BYrJOUFSOBUJPOBM!QFOUFLàMUSBUJPODPN www.pentekfiltration.com Printed in USA MR06 310069

rfc series radiaL fLoW carbon cartridges

• Provides effective chlorine taste & odor reduction*

• bb cartridges are ideal for point-of-entry (Poe) and other high flow rate applications

• Unique design reduces carbon fines in filtered water

• available in a wide variety of sizes

RFC Series cartridges are constructed with a 70-micron porous polyethylene outer shell and durable polypropylene end caps. The 2

⁄

" OD cartridges have a polypropylene core and the 4

⁄

OD cartridges incorporate a spun polypropylene core. Sandwiched between the outer shell and the core is a bed of granular activated carbon

(GAC).

The unique radial flow design offers the benefits of granular activated carbon (GAC) filtration, such as low pressure drop, while at the same time significantly reducing the release of carbon fines commonly associated with GAC style cartridges.

RFC Series cartridges are available in a wide variety of sizes and are ideal point-of-entry (POE) and other high flow rate applications.

* Based on manufacturer’s internal testing.

RFC-20

RFC-BB

RFC20-BB

rfc series

radial flow carbon cartridges

3'$##

3'$

3'$##

'MPX3BUFoHQN -QN cartridge specifications and Performance data

Model Maximum dimensions

RFC-93

RFC-20

RFC-BB

RFC20-BB

⁄

" x 9

⁄

" (70 mm x 248 mm)

" x 20" (70 mm x 508 mm)

" x 9

⁄

" (114 mm x 248 mm)

" x 20" (114 mm x 508 mm)

* based on manufacturer's internal testing initial ∆P (psi)

@ flow rate (gpm)

0.60 psi @ 1 gpm (0.04 bar @ 3.8 Lpm)

0.60 psi @ 2 gpm (0.04 bar @ 7.6 Lpm)

0.90 psi @ 2 gpm (0.06 bar @ 7.6 Lpm)

0.90 psi @ 4 gpm (0.06 bar @ 15.1 Lpm)

chlorine taste & odor reduction @ flow rate

>3000 gallons @ 1 gpm (11,400L @ 3.8 Lpm)

>6000 gallons @ 2 gpm (22,700L @ 7.6 Lpm)

>35,000 gallons @ 2 gpm (132,500L @ 7.6 Lpm)

>70,000 gallons @ 4 gpm (265,000L @ 15.1 Lpm)

Materials of construction

Filter Media

Outer Shell

Granular Activated Carbon

Polyethylene

The TSGAC-10 is Tested and Certified by

NSF International to NSF/ANSI Standard

42 for material requirements only.

End Caps

Gasket

Inner Wraps/Core

Temperature Rating

Polypropylene

Buna-N

Polypropylene

40–125ºF (4.4–51.7ºC)

WARNING:

Do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the system.

NOTE:

The granular activated carbon cartridges will contain a very small amount of carbon fines (very fine black powder). After installation, a new cartridge should be flushed with sufficient water to remove all traces of the fines from your water system before using the water. Each time you use your filtered water tap for drinking or cooking purposes it is recommended that you run (flush) the tap for at least 20 seconds prior to using water. This is particularly important if the water tap has not been used daily.

502 Indiana Avenue • P.O. Box 1047 • Sheboygan, Wisconsin 53082-1047

CCustomer Service: 800.645.0267 • Fax: 888.203.7361 • [email protected]

International: 920.457.9435 • Fax: 920.457.2417 • [email protected]

www.pentekfiltration.com Printed in USA MR06 310075

SCBC-10 ANTI–MICROBIAL CARBON BLOCK CARTRIDGE

t5SFBUFEXJUICBDUFSJPTUBUUPFGGFDUJWFMZSFEVDFUIFHSPXUIPGCBDUFSJBPOUIFmMUFSNFEJB t/PNJOBMoNJDSPOSBUJOH tSFEVDUJPOPG

Cryptosporidium, Giardia, Enamoeba,

BOE

Toxoplasma

DZTUT t1SFNJVNIJHIDBQBDJUZCBEUBTUFPEPSBOEDIMPSJOFUBTUFPEPSSFEVDUJPO t&OIBODFEEJSUIPMEJOHDBQBDJUZ

The SCBC-10 cartridge contains a highly effective anti–microbial compound with controlled silver release that provides long–lasting protection of the activated carbon surfaces from bio–fouling bacteria.

The SCBC-10 cartridge is highly effective at reducing unwanted taste & odor and chlorine taste & odor from potable drinking water.

With a nominal 0.5–micron rating, it is equally effective at reducing fine sediment and cysts such as

Cryptosporidium

and

Giardia

The SCBC-10 cartridge is manufactured using a patented process and is made from activated carbon that is tested for purity and performance prior to manufacture.

This process and media yields a cartridge with high chlorine taste & odor reduction capacity.

This cartridge is protected by Endurawrap ™ , a uniquely formulated polyolefin bilaminate pre–filter, designed to significantly increase the useful life of the cartridge by trapping sediment that typically plugs carbon block cartridges.

This is an ideal choice for a wide range of residential, food service, commercial and industrial applications. They also make excellent polishing filters or pre– filters in applications requiring fine filtration and high capacity.

SCBC-10

SCBC-10

"OUJo.JDSPCJBM$BSCPO#MPDL$BSUSJEHF

1BSUJDMF4J[F .JDSPOT

'MPX3BUFoHQN -QN

.PEFM

SCBC-10

.BYJNVN%JNFOTJPOT

2 7 ⁄

" x 9 3 ⁄

" (73mm x 248mm)

.JDSPO3BUJOH

/PNJOBM

0.5

*OJUJBMå1 QTJ

!'MPX3BUF HQN

12 psi @ 1 gpm

(0.83 bar @ 3.8 Lpm)

$IMPSJOF5BTUF0EPS3FEVDUJPO

!'MPX3BUF HQNp

>20,000 gallons @ 1 gpm

(>75,700 liters @ 3.8 Lpm)

.BUFSJBMTPG$POTUSVDUJPO

Filter Media

End Caps

Inner/Outer Wraps

Netting

Gaskets

Temperature Rating

Silver Content

Bonded PAC

Polypropylene

Polyolefin

Polyethylene

Polyolefin

40–165ºF (4.4–73.9ºC)

0.05% by weight

NOTE:

Performance capacity depends on system design, flow rate and certain other application conditions. Certain states require system registration or certification for health–related contaminant reduction claims.

WARNING:

Do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the system.

NOTE:

Cartridge may contain a very small amount of carbon fines (very fine black powder) and a new cartridge after installation should be flushed with sufficient water to remove all traces of the fines from your water system before using the water.

NOTE:

Nominal micron ratings based on 85% or greater removal of given particle size.

NOTE:

The SCBC-10 cartridge is capable of reducing 99.95% of Cryptosporidium and Giardia cysts. Data obtained from actual test dust and particle counts using Latex spheres.

† Estimated capacity using 2ppm free available chlorine (FAC) with greater than 90% reduction.

U.S. Patent No. 5,976,432 & 5,823,668

EPA Est. 03981-WI-001

*OEJBOB"WFOVFr10#PYr4IFCPZHBO8JTDPOTJO

$VTUPNFS4FSWJDFr'BYrTVQQPSUTQFDJBMJTU!QFOUFLàMUSBUJPODPN

*OUFSOBUJPOBMr'BYrJOUFSOBUJPOBM!QFOUFLàMUSBUJPODPN www.pentekfiltration.com Printed in USA MR06 310018

TSGAC SPECIALTY GRANULAR ACTIVATED

CARBON/PHOSPHATE CARTRIDGE

t&GGFDUJWFCBEUBTUFPEPSBOEDIMPSJOFUBTUFPEPSSFEVDUJPO t1IPTQIBUFDSZTUBMTSFEVDFSVTUTUBJOTBOETDBMFEFQPTJUT t%FTJHOFEGPSNBYJNVNBETPSQUJPO t1PTUmMUFSUPSFEVDFDBSCPOmOFT

TSGAC cartridges contain granular activated carbon to effectively reduce unwanted taste and odor and chlorine taste and odor, as well as phosphate crystals to reduce rust stains and scale deposits.*

The construction of the cartridge allows water to enter at one end and pass through the entire length of the carbon bed before exiting the other end of the cartridge. An internal expansion pad minimizes channeling or bypass. This design allows for maximum contact between the water and carbon, ensuring maximum adsorption.

Before the water exits the cartridge, a 20-micron post filter helps remove carbon fines and other suspended particles from the filtered water. The post filter is permanently fastened to an innovative support basket ensuring that it is firmly secured and eliminating any potential for bypass.

TSGAC cartridges provide superior performance and outstanding protection for your water lines, fixtures, major appliances and commercial equipment.

* Based on manufacturer’s internal testing.

TSGAC-10

TSGAC CARTRIDGE

4QFDJBMUZ(SBOVMBS"DUJWBUFE$BSCPO1IPTQIBUF$BSUSJEHF

54("

'MPX3BUFoHQN -QN

$BSUSJEHF4QFDJmDBUJPOTBOE1FSGPSNBODF%BUB

.PEFM

.BYJNVN%JNFOTJPOT

TSGAC-10 2 7 ⁄

" x 9 3 ⁄

" (73 mm x 248 mm)

#BTFEPONBOVGBDUVSFShTJOUFSOBMUFTUJOH

*OJUJBMå1 QTJ

!'MPX3BUF HQN

2.5 psi @ 1.0 gpm (0.2 bar @ 3.8 Lpm)

$IMPSJOF5BTUF0EPS

3FEVDUJPO!'MPX3BUF

>2000 gallons @ 1 gpm (7570L @ 3.8 Lpm)

.BUFSJBMTPG$POTUSVDUJPO

Filter Media

Granular Activated Carbon

Hexametaphosphate Crystals

The TSGAC-10 is Tested and Certiﬁed by

NSF International to NSF/ANSI Standard

42 for material requirements only.

End Caps

Post-Filter

Outer Casing

Expansion Pad

Polystyrene

Spun Polypropylene

Polystyrene

Polypropylene

Gasket

Buna-N (top)

Santoprene (bottom)

Temperature Rating

40–125ºF (4.4–51.7ºC)

WARNING:

Do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the system.

NOTE:

A drinking water cartridge may contain carbon fines (very fine black powder). After installation and before using the water, flush the cartridge for 5 minutes to remove fines.

NOTE:

It is recommended that you run the tap for 20 seconds prior to using the water for drinking or cooking purposes.

*OEJBOB"WFOVFr10#PYr4IFCPZHBO8JTDPOTJO

$VTUPNFS4FSWJDFr'BYrTVQQPSUTQFDJBMJTU!QFOUFLàMUSBUJPODPN

*OUFSOBUJPOBMr'BYrJOUFSOBUJPOBM!QFOUFLàMUSBUJPODPN www.pentekfiltration.com Printed in USA MR06 310074

CRE-1 CERAMIC CARTRIDGE

t4QFDJBMMZEFTJHOFEGPSDZTUSFEVDUJPOBOEmOFTFEJNFOUmMUSBUJPOBQQMJDBUJPOT tUIJDLDFSBNJDXBMMBMMPXTGPSNBOZDMFBOJOHTFYUFOEJOHDBSUSJEHFMJGF t/PNJOBMNJDSPOSBUJOH

CRE-1 cartridges are manufactured from a sintered ceramic filtration media. They are designed and tested for the reduction of

Cryptosporidium and Giardia cysts, and are ideal for fine sediment filtration applications.

The fine ceramic media will effectively trap dirt, sediment and cysts down to 1-micron in diameter.

A proper fit is ensured and water bypass is prevented through the use of a knife-edge seal.

CRE-1 cartridges are easily cleaned with water and a damp cloth, sponge or stiff nylon brush. They can be cleaned several times until the diameter at the smallest point is 1

⁄

" or the circumference is 4

⁄

", extending cartridge life.

NOTE: Not for residential sale in the state of California.

CRE-1

$FSBNJD$BSUSJEHF

$3&

1BSUJDMF4J[F .JDSPOT

'MPX3BUFoHQN -QN

$BSUSJEHF4QFDJmDBUJPOTBOE1FSGPSNBODF%BUB

CRE-1

.PEFM

.BYJNVN%JNFOTJPOT

1 ⁄ " x 9

⁄

NNYNN

.JDSPO3BUJOH OPNJOBM

*OJUJBMå1 QTJ

!'MPX3BUF HQN

QTJ!HQN CBS!-QN

.BUFSJBMTPG$POTUSVDUJPO

Filter Media

End Caps

4JOUFSFE$FSBNJD

5IFSNPTFU1PMZNFSJD

Gasket

Temperature Rating

#VOB/ m' m$

NOTE: Performance depends on system design, flow rate, feed water quality and certain other application conditions. Certain states require system registration or certification prior to sale if health-related contaminant reduction claims are made. Not for residential sale in the state of California.

NOTE: Only a thin layer of ceramic is removed with each cleaning. It is not necessary to clean the cartridge until the original color is restored as water in some locations may stain or discolor the ceramic.

Good hygiene and housekeeping practices should always be used when cleaning the CRE-1 cartridge.

HANDLE CARTRIDGE WITH CARE! Sharp blows, dropping or freezing can cause cracks in the ceramic. If the cartridge should be cracked or frozen, discard the damaged cartridge and replace it with a new cartridge.

WARNING: Do not use where water is microbiologically unsafe or with water of unknown quality without adequate disinfection before or after the system. Cartridge specifically designed for sediment filtration and the reduction of Giardia and Cryptosporidium cysts, not to kill or filter bacteria.

¥1FOUBJS'JMUSBUJPO*OD

*OEJBOB"WFOVFr10#PYr4IFCPZHBO8JTDPOTJO

$VTUPNFS4FSWJDFr'BYrTVQQPSUTQFDJBMJTU!QFOUFLàMUSBUJPODPN

*OUFSOBUJPOBMr'BYrJOUFSOBUJPOBM!QFOUFLàMUSBUJPODPN

XXXQFOUFLàMUSBUJPODPN 1SJOUFEJO64".3

CW/WP SERIES POLYPROPYLENE

WOUND CARTRIDGES

t4USJOHXPVOEEFTJHOSFEVDFTmOFTFEJNFOUGSPNBWBSJFUZPGnVJET t8JUITUBOETUFNQFSBUVSFTVQUP' $ t&DPOPNJDBMMZQSJDFE t/PNJOBMNJDSPOSBUJOH $8BOEOPNJOBMNJDSPOSBUJOH 81

CW and WP Series cartridges are manufactured from a durable polypropylene cord that is wound around a rigid polypropylene core.

They are an economical solution to reduce fine sediment, including sand, silt, rust and scale particles.

CW cartridges are very economical and wound in a standard pattern around the core. They are available in 10, 30 and 50-micron ratings.

WP Series cartridges are wound in a precise pattern around the core providing greater surface area. The result is higher dirt-loading capacity and greater efficiency than standard wound cartridges like the CW.

Both of these string-wound cartridge styles are capable of withstanding temperatures up to 165ºF (73.9ºC), and will accommodate flow rates between 7 and 10 GPM with minimal pressure drop.

CW and WP Series cartridges are suitable for a wide variety of sediment filtration applications, including municipal and well water as well as many industrial fluids.

CW/WP SERIES

1PMZQSPQZMFOF8PVOE$BSUSJEHFT

$8'

$8.'

CW-F

CW-MF

CW-50

WP-5

WP-30

1BSUJDMF4J[F .JDSPOT

$BSUSJEHF4QFDJmDBUJPOTBOE1FSGPSNBODF%BUB

.PEFM

.BYJNVN%JNFOTJPOT

⁄

" x 9

⁄

" (60 mm x 251 mm)

2 1 ⁄

" x 9 7 ⁄

" (60 mm x 251 mm)

⁄

" x 9

⁄

" (60 mm x 251 mm)

2 1 ⁄

" x 9 7 ⁄

" (60 mm x 251 mm)

⁄

" x 9

⁄

" (60 mm x 251 mm)

.JDSPO3BUJOH OPNJOBM

.BUFSJBMTPG$POTUSVDUJPO

Filter Media

Core

Temperature Rating

Polypropylene Fiber Cord

Polypropylene

40–145ºF (4.4–62.8ºC)

WARNING: Do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the system.

*OJUJBMå1 QTJ

!'MPX3BUF HQN

<1 psi @ 10 gpm (<0.07 bar @ 38 Lpm)

<2.5 psi @ 10 gpm (<0.17 bar @ 38 Lpm)

<1.4 psi @ 10 gpm (<0.17 bar @ 38 Lpm)

*OEJBOB"WFOVFr10#PYr4IFCPZHBO8JTDPOTJO

$VTUPNFS4FSWJDFr'BYrTVQQPSUTQFDJBMJTU!QFOUFLàMUSBUJPODPN

¥1FOUBJS3FTJEOUJBM'JMUSBUJPO--$

*OUFSOBUJPOBMr'BYrJOUFSOBUJPOBM!QFOUFLàMUSBUJPODPN

XXXQFOUFLàMUSBUJPODPN 1SJOUFEJO64"0$

dgd series dUaL-gradieNt deNsitY cartridges

• Manufactured from pure 100% polypropylene

• designed for purity and chemical compatibility

• spun fibers form a true gradient density from outer to inner surfaces

DGD Series cartridges are manufactured from 100% pure polypropylene and are sized for use in our Big Blue

filter housings.

DGD Series cartridges are designed for purity and will not impart taste, odor or color to the liquid being filtered. Additionally, the polypropylene construction provides superior chemical resistance and is not prone to bacterial attack.

The DGD Series' advanced design combines selective final filtration with appropriate pre-filtration to achieve up to three times the dirt-holding capacity of similar size sediment cartridges and even greater capacity than standard spun or string-wound cartridges.

This performance enhancement is achieved by combining two separate gradient layers in one filter.

The larger diameter of the pre-filter reduces the particle load to the post filter, allowing it to operate at higher velocities. The effective filter depth is increased to a full 233% of standard spun-polypropylene or string-wound filters. This increased depth provides for very high particulate reduction efficiencies and added loading capacity.

The unique design and performance characteristics of the DGD

Series cartridges make them an excellent choice for all residential, rural, municipal and commercial applications.

dgd series

dual-gradient density cartridges

%(%

1BSUJDMF4J[F .JDSPOT

'MPX3BUFoHQN -QN cartridge specifications and Performance data

Model Maximum dimensions Micron rating* (nominal)

DGD-2501

DGD-5005

DGD-7525

DGD-2501-20

DGD-5005-20

DGD-7525-20

⁄

" x 10" (114 mm x 254 mm)

⁄

" x 10" (114 mm x 254 mm)

⁄

" x 10" (114 mm x 254 mm)

⁄

" x 20" (114 mm x 508 mm)

⁄

" x 20" (114 mm x 508 mm)

⁄

" x 20" (114 mm x 508 mm)

Pre-filter: 25

Post filter: 1

Pre-filter: 50

Post filter: 5

Pre-filter: 75

Post filter: 25

Pre-filter: 25

Post filter: 1

Pre-filter: 50

Post filter: 5

Pre-filter: 75

Post filter: 25

* Based on manufacturer's internal testing

Materials of construction

Filter Media

Temperature Rating

Polypropylene

40–145ºF (4.4–62.8ºC)

WARNING: Do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the system.

initial ∆P (psi)

@ Flow rate (gpm)

<1 psi @ 10 gpm (<0.1 bar @ 38 Lpm)

<1 psi @ 20 gpm (<0.1 bar @ 76 Lpm)

Tested and Certified by NSF International to NSF/ANSI Standard 42 for material requirements only.

502 Indiana Avenue • P.O. Box 1047 • Sheboygan, Wisconsin 53082-1047

Customer Service: 800.645.0267 • Fax: 888.203.7361 • [email protected]

International: 920.457.9435 • Fax: 920.457.2417 • [email protected]

www.pentekfiltration.com Printed in USA MR06 310061

ECP1-20

ECP SERIES PLEATED CELLULOSE

POLYESTER CARTRIDGES

t3FQMBDFT$1BOE)'$14FSJFTDBSUSJEHFT t4QFDJBMGPSNVMBUJPOPGSFTJOJNQSFHOBUFEDFMMVMPTFBOEQPMZFTUFSmCFST t1SPWJEFTIJHIFSXFUTUSFOHUIUIBOSFHVMBSDFMMVMPTFDBSUSJEHFT t.JOJNBMVOMPBEJOHBOENFEJBNJHSBUJPO

ECP Series cartridges are manufactured from a special formulation of resin-impregnated cellulose and polyester fibers.

This unique blend of materials provides a higher wet strength than regular cellulose cartridges. It also provides high flow rates and dirtholding capacity, while maintaining extremely low pressure drop.

The media is pleated around a polypropylene core for added strength and the ends are immersed in a thermo-setting vinyl plastisol.

Embedding and sealing each end of the pleat block in this fashion fuses the components together forming a unified endcap and gasket.

ECP Series cartridge endcaps feature a color-coding system for easy identification of micron ratings: Tan

(1-micron), White (5-micron), Blue

(20-micron), Yellow (50-micron).

ECP cartridges contain more media surface area than most competitive cartridges. The standard 10-inch

ECP cartridge contains six square feet of media, where most cartridges contain only 4.5 square feet. Other available ECP cartridge sizes contain the following amount of media: r4UBOEBSEJODIDBSUSJEHFmGU

2 rJODI##DBSUSJEHFmGU 2 rJODI##DBSUSJEHFmGU

ECP50-BB

ECP5-10

ECP20-20BB

ECP SERIES

1MFBUFE$FMMVMPTF1PMZFTUFS$BSUSJEHFT

&$1

1BSUJDMF4J[F .JDSPOT

$BSUSJEHF4QFDJmDBUJPOTBOE1FSGPSNBODF%BUB

.PEFM

ECP1-10

ECP5-10

ECP20-10

ECP50-10

ECP1-20

ECP5-20

ECP20-20

ECP50-20

ECP1-BB

ECP5-BB

ECP20-BB

ECP50-BB

ECP1-20BB

ECP5-20BB

ECP20-20BB

ECP50-20BB

&OEDBQ

$PMPS

Tan

Yellow

Tan

White

Blue

Yellow

Tan

White

Blue

Yellow

Tan

White

Blue

White

Blue

Yellow

.BYJNVN%JNFOTJPOT

2 5 ⁄ " x 9 ⁄

NNYNN

2 5 ⁄ " x 9 ⁄

NNYNN

⁄ " x 9 ⁄

NNYNN

2 5 ⁄ " x 9 ⁄

NNYNN

2 5 ⁄ Y NNYNN

⁄ Y NNYNN

2 5 ⁄ Y NNYNN

⁄

" x 9 ⁄

NNYNN

4 1 ⁄

" x 9 ⁄

NNYNN

4 1 ⁄

" x 9 ⁄

NNYNN

⁄

" x 9 ⁄

NNYNN

4 1 ⁄

Y NNYNN

4 1 ⁄

Y NNYNN

4 1 ⁄

Y NNYNN

4 1 ⁄

Y NNYNN

.BUFSJBMTPG$POTUSVDUJPO

Media Cellulose Polyester

Core

Endcaps

Polypropylene

Vinyl Plastisol

Temperature Rating m' m$

WARNING: Do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the system.

.JDSPO3BUJOH

/PNJOBM

*OJUJBMå1 QTJ!'MPX3BUF HQN

QTJ!HQN CBS!-QN

¥1FOUBJS'JMUSBUJPO*OD

*OEJBOB"WFOVFr10#PYr4IFCPZHBO8JTDPOTJO

$VTUPNFS4FSWJDFr'BYrTVQQPSUTQFDJBMJTU!QFOUFLàMUSBUJPODPN

*OUFSOBUJPOBMr'BYrJOUFSOBUJPOBM!QFOUFLàMUSBUJPODPN

XXXQFOUFLàMUSBUJPODPN 1SJOUFEJO64"+&

FILTRATION

COMPONENTS

Gradient Density Cartridges

GD/GDA Series

The new GD and GDA Series of cartridges are manufactured in the USA from 100% pure polypropylene and are sized for use in the PENTEK

10" and 20" Big Blue housings.

GD and GDA Series are designed for purity and will not impact taste, odor and color and provide superior chemical resistance and are not prone to bacterial attack.

Two unique layers provide up to three times the dirt-holding capacity than pleated, string-wound and standard spun polypropylene cartridges provide. A larger outer pre-filter reduces the partial load to the inner post filter allowing the cartridge to operate at higher velocities and lower pressure drop. The effective filter depth is increased over

200% of string-wound and standard spun-polypropylene cartridges for extended life, performance and reliability.

The design and performance characteristics of the GD and GDA Series Cartridges make them an excellent choice for all residential, rural, municipal, industrial, and commercial applications.

Typical Applications

• Well Water

• City Water

• Homes

• Cafeterias

• Hotel/Motel

• Laboratories

• Laundromats

• Restaurants

• Schools

• Factories

FILTRATION

COMPONENTS

Gradient Density

Cartridges

GD/GDA Series

Features and Benefits

•

100% polypropylene filtration media for superior purity without affecting taste, odor or color.

•

Two clearly visible gradient layers ensure higher efficiency and improved performance.

•

Micron ratings for virtually any application

(75-25 for outer layer,

20-0.5 inner layer).

•

GDA Series has polypropy- lene inner support core for added strength and unimpeded flow.

•

Polypropylene filter media resists chemicals and bacterial attack.

•

Up to three times the dirt-holding capacity of similar-sized pleated, string-wound and spunpolypropylene cartridges.

•

Effectively reduces sediment as a pre-filter to softener and automatic filter systems.

•

Saves space – all-in-one, two-layer cartridge eliminates the need for additional filter canisters.

Materials of Construction

Filter Media

Temperature Rating

Polypropylene

40 - 145ºF (4.4 - 62.8ºC)

Cartridge Specifications and Performance Data

Model

GD-7520-BB

GD-5010-BB

GD-2501-BB

GD-7520-20BB

GD-5010-20BB

GD-2501-20BB

GDA-7505-BB

GDA-5001-BB

GDA-250.5-BB

GDA-7505-20BB

GDA-5001-20BB

GDA-250.5-20BB

Maximum Dimensions

4-1/2 " x 9-7⁄ 8 " (114 mm x 251 mm)

4 -1/2 " x 9-7⁄ 8 " (114 mm x 251 mm)

4-1/2 " x 20" (114 mm x 508 mm)

4 -1/2 " x 20" (114 mm x 508 mm)

4-1/2 " x 9-7⁄ 8 " (114 mm x 251 mm)

4 -1/2 " x 9-7⁄ 8 " (114 mm x 251 mm)

4-1/2 " x 20" (114 mm x 508 mm)

Micron Rating*

Nominal

Absolute

Performance – Flow Rate Characteristics

0 7.6

Flow Rate (Lpm)

15.1

22.7

30.3

37.9

1.52

1.38

1.24

1.10

0.97

0.83

0.69

0.55

0.41

0.28

0.14

0 2 4 6 8

Flow Rate in Gallons Per Minute

GD-7520-BB

GD-5010-BB

GD-7520-20BB

GD-2501-BB

GD-5010-20BB

GDA-7505-BB

GD-2501-20BB

GDA-5001-BB

GDA-7505-20BB

GDA-250.5-BB

GDA-5001-20BB

GDA-250.5-20BB

Micron Size

Outside 75 - Core 20

Outside 50 - Core 10

Outside 25 - Core 1

Outside 75 - Core 20

Outside 50 - Core 10

Outside 25 - Core 1

Outside 75 - Core 5

Outside 50 - Core 1

Outside 25 - Core 0.5

Outside 75 - Core 5

Outside 50 - Core 1

Outside 25 - Core 0.5

Initial ΔP (psi) @ Flow Rate (gpm)

<1.5 psi @ 10 gpm (<0.1 bar @ 38 Lpm)

<2 psi @ 10 gpm (<0.1 bar @ 38 Lpm)

<3.2 psi @ 10 gpm (<0.2 bar @ 38 Lpm)

<3 psi @ 10 gpm (<0.2 bar @ 38 Lpm)

<4 psi @ 10 gpm (<0.3 bar @ 38 Lpm)

<6.4 psi @ 10 gpm (<6.4 bar @ 38 Lpm)

<5.2 psi @ 10 gpm (<0.4 bar @ 38 Lpm)

<9 psi @ 10 gpm (<0.6 bar @ 38 Lpm)

<10.5 psi @ 10 gpm (<0.7 bar @ 38 Lpm)

<10.4 psi @ 10 gpm (<0.7 bar @ 38 Lpm)

<18 psi @ 10 gpm (<1.2 bar @ 38 Lpm)

<21 psi @ 10 gpm (<1.4 bar @ 38 Lpm)

*Based on manufacturer’s internal testing.

WARNING: Do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the system.

Tested and Certified by NSF International to NSF/

ANSI Standard 42 for material requirements only.

5730 North Glen Park Road

Milwaukee, WI 53209

Tel: 262.238.4400

Fax: 262.238.4402

Customer Care: 800.279.9404 www.pentairaquapro.com

311006 Rev A AU10

MICROGUARD™ SERIES

MEMBRANE FILTER CARTRIDGES

t"CTPMVUFNJDSPOQBSUJDMFSFUFOUJPOGPSCBDUFSJBBOE

QSPUP[PBODZTUSFEVDUJPO tCBDUFSJBSFEVDUJPO -PH tDZTUSFEVDUJPO -PH t$PNCJOFEDBSCPOCMPDLBOETFEJNFOUQSFmMUSBUJPOGPS

FYUFOEFEMJGFBOEDIMPSJOFUBTUFBOEPEPSSFEVDUJPO

The MicroGuard™ membrane filters provide reliable bacteria and protozoan cyst reduction for safer and cleaner drinking water without incorporating chemicals into the media or adding chemicals to the filtered water. The MicroGuard carbon block membrane cartridge,

MG-10MCB, is uniquely designed with integral carbon block and sediment pre-filtration for the reduction of chlorine taste and odor and for providing extended life of the internal membrane element. This cartridge has 2.5 times greater filtration surface area than some anti-microbial carbon blocks and operates at a higher flow rate with lower pressure drop. This

MG-10T

MG-10MCB

t6UJMJ[FTQBUFOUFEIJHIMZBTZNNFUSJDQPMZFUIFSTVMGPOF

NFNCSBOFXJUIQSPQSJFUBSZIZESPQIJMJDGPSNVMBUJPOGPS

JNNFEJBUFXFUUJOHBOEIJHInPX t%PVCMF0SJOHFOEDBQTFBMTGPSBCTPMVUFTFBMJOHJO

1&/5&,4FBM4BGF(IPVTJOHT

makes the MG-10MCB ideal for

Point-of-Use (POU) applications.

The MicroGuard cartridges do not require USEPA registration and their effectiveness is not susceptible to common substances normally found in some waters, e.g., hydrogen sulfide (H

S), natural organic matter

(NOM) and total dissolved solids

(TDS).

The MicroGuard triple-element cartridge, MG-10T, is uniquely constructed with three membrane elements integrally sealed into one common cartridge design. This unique design allows for higher flow rates and longer life while still providing bacteria and cyst reduction, and is ideal for applications up to five gallons-per-minute. The life of the MG-10T can be extended using

PENTEK carbon block or sediment pre-filtration options.

*U.S. Patent No. 5,240,862

EPA Est. No. 039861-WI-001

Not certified for sale in California, Iowa, Massachusetts and Wisconsin.

NOTE: These cartridges are not intended for converting wastewater or raw sewage into drinking water.

FEATURES AND BENEFITS

%FTDSJQUJPOBOE%JNFOTJPOT

MG-10MCB

r$BSCPO#MPDL.FNCSBOF

rJODIOPNJOBMMFOHUINJDSPàMUFS NJDSPOBCTPMVUFSBUJOH r.BYJNVNEJBNFUFS NN.BYJNVN-FOHUI NN r'JUTJO PENTEK (IPVTJOHT4MJN-JOF ® and Standard.

MG-10T

r5SJQMF&MFNFOU$BSUSJEHF rJODIOPNJOBMMFOHUINJDSPàMUFS NJDSPOBCTPMVUFSBUJOH r.BYJNVNEJBNFUFS NN.BYJNVN-FOHUI NN r'JUTJO PENTEK (IPVTJOHT4MJN-JOF ® and Standard.

"EWBOUBHFTPGUIF.JDSP(VBSE'JMUFS5FDIOPMPHZ

r3FRVJSFTPOMZOPSNBMXBUFSMJOFQSFTTVSFUPPQFSBUF r/PFMFDUSJDBMQPXFSSFRVJSFE FYDFQUGPSBDDFTTPSZQVNQJGOFFEFEGPS pressure) r1SPUFDUTFWFOEVSJOHQPXFSPVUBHFTPSJOUFSNJUUFOUQPXFS r/PXBTUFXBUFSPSCSJOFDPODFOUSBUFáVTIJOH r3FUBJOTOBUVSBMNJOFSBMDPOUFOUPGXBUFS r1SPUFDUTBHBJOTUVOFYQFDUFECBDUFSJBBOEDZTUTJOUIFXBUFSTZTUFNEVF to water main breaks, water treatment plant failure during floods and power outages r)JHITVSGBDFBSFBBOETVQFSJPSUPMFSBODFUPQMVHHJOH r-PXQSFTTVSFESPQXJUIIJHIáPXSBUF r1SPUFDUJPOOPUTVTDFQUJCMFUPDPNNPOTVCTUBODFTJOXBUFSTVDIBT hydrogen sulfide (H

S), natural organic matter (NOM) and total dissolved solids (TDS) r#BDUFSJBBOEDZTUSFNPWBMEPFTOPUSFMZPODIFNJDBMT

1PJOUPG6TF 106"QQMJDBUJPOT

MG-10MCB

r6OEFSTJOLTFQBSBUFUBQ r$PVOUFSUPQ r8BUFSGPSm

oral care

food preparation

hand washing r-BCPSBUPSJFT r1IPUPHSBQIZàMN r0GàDFTSFTUBVSBOUT r$PGGFFNBLFST

MG-10T

r*OMJOF DPMEXBUFSMJOF r#FWFSBHFEJTQFOTJOH r8BUFSGPSm

oral care

food preparation

hand washing r-BCPSBUPSJFT r1IPUPHSBQIZàMN r1SPDFTTXBUFS r0GàDFTSFTUBVSBOUT

Not certified for sale in California, Iowa, Massachusetts and Wisconsin.

Note: These cartridges are not intended for converting wastewater or raw sewage into drinking water.

.(5

MG-CCBR MICROGUARD™

MEMBRANE FILTER CARTRIDGE

t"CTPMVUFNJDSPOQBSUJDMFSFUFOUJPOGPSCBDUFSJBMBOEQSPUP[PBODZTUSFEVDUJPO tCBDUFSJBSFEVDUJPO -PH tDZTUSFEVDUJPO -PH tNJDSPODPDPOVUDBSCPOTIFMMDBSCPOCMPDLQSFmMUFS t-FBE.FSDVSZBOE70$SFEVDUJPO

The MG-CCBR Microguard membrane filter cartridge provides combined carbon block and sediment pre-filtration for extended life and chlorine taste & odor reduction as well as lead, mercury, cyst, bacteria and VOC reduction.

This cartridge utilizes patented* highly asymmetric polyethersulfone membrane with proprietary hydrophilic formulation for immediate wetting and high flow.

The MG-CCBR has a single openended gasket seal and fits all 10" standard and 3G PENTEK ® filter housings.

*U.S. Patent No. 5,240,862

EPA Est. No. 039861-WI-001

Not certified for sale in California, Iowa, Massachusetts and Wisconsin

NOTE: These cartridges are not intended for converting wastewater or raw sewage into drinking water.

MG-CCBR

MG-CCBR MICROGUARD

™

.FNCSBOF'JMUFS$BSUSJEHF

"EWBOUBHFTPGUIF.JDSP(VBSE ™ mMUFSUFDIOPMPHZ

r3FNPWFTCBDUFSJBDZTUTBOEPUIFSQBSUJDMFTEPXOUPNJDSPOJOTJ[F r3FRVJSFTPOMZOPSNBMXBUFSMJOFQSFTTVSFUPPQFSBUF r/PFMFDUSJDBMQPXFSSFRVJSFE FYDFQUGPSBDDFTTPSZQVNQJGOFFEFEGPSQSFTTVSF r1SPUFDUTFWFOXJUIQPXFSPVUBHFTPSJOUFSNJUUFOUQPXFS r/PXBTUFXBUFSPSCSJOFDPODFOUSBUFáVTIJOH r3FUBJOTOBUVSBMNJOFSBMDPOUFOUPGXBUFS r1SPUFDUTBHBJOTUVOFYQFDUFECBDUFSJBBOEDZTUTJOUIFXBUFSTZTUFNEVFUPXBUFS main breaks, water treatment plant failure during floods and power outages r)JHITVSGBDFBSFBBOEIJHIUPMFSBODFUPQMVHHJOH r-PXQSFTTVSFESPQXJUIIJHIáPXSBUF r1SPUFDUJPOOPUTVTDFQUJCMFUPDPNNPOTVCTUBODFTJOXBUFSTVDIBTIZESPHFO

TVMàEF )4OBUVSBMPSHBOJDNBUUFS /0.BOEUPUBMEJTTPMWFETPMJET 5%4 r#BDUFSJBBOEDZTUSFNPWBMEPFTOPUSFMZPODIFNJDBMT r$PDPOVUTIFMMBDUJWBUFEQPXEFSDBSCPOQSPEVDFTFYDFMMFOUUBTUJOHXBUFS

$BSUSJEHF4QFDJmDBUJPOTBOE1FSGPSNBODF%BUB

.PEFM

MG-CCBR

.BYJNVN%JNFOTJPOT

⁄

" x 9

⁄

" (73mm x 248mm)

.JDSPO3BUJOH

"CTPMVUF

0.15

*OJUJBMå1 QTJ!'MPX3BUF HQN

21.5 psi @ 0.6 gpm (1.5 bar @ 2.3 L/min)

.BUFSJBMTPG$POTUSVDUJPO r.FNCSBOF

Polyethersulfone

r.FNCSBOF"TTFNCMZ r&OE$BQT r/FUUJOH

Polystyrene, epoxy resin

Polypropylene

Polyolefin

r(BTLFUT

Santoprene

8"3/*/(

Do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the system.

¥1FOUBJS'JMUSBUJPO*OD

*OEJBOB"WFOVFr10#PYr4IFCPZHBO8JTDPOTJO

$VTUPNFS4FSWJDFr'BYrTVQQPSUTQFDJBMJTU!QFOUFLàMUSBUJPODPN

*OUFSOBUJPOBMr'BYrJOUFSOBUJPOBM!QFOUFLàMUSBUJPODPN

XXXQFOUFLàMUSBUJPODPN 1SJOUFEJO64"+&(

OIL ADSORBING CARTRIDGE

t.PEJmFEDFMMVMPTFCBTFEmMUFSNBUFSJBMDIFNJDBMMZCPOETTQFDJmDBMMZXJUIIZESPDBSCPOTBOEPUIFSQPMMVUBOUT

TVDIBTEJTTPMWFEBOEEJTQFSTFEPJMTJOXBUFS t*OTUBOUBOFPVTBETPSQUJPONPSFFGGFDUJWFUIBOBDUJWBUFEDBSCPO t6QUPQFSDFOUPGUPUBMIZESPDBSCPOTBSFSFNPWFEJOBTJOHMFQBTT t'PSVTFJOJODI#JH#MVF ® mMUFSIPVTJOHT

OAC-20BB

The OAC-20BB filter cartridge is made from modified cellulose-based filter media which is processed into sheets and assembled into cartridges for use in standard 20-inch Big Blue filter housings.

Features

r*OTUBOUBOFPVTBETPSQUJPOmVQUP

90 percent of total hydrocarbons removed in a single pass r)JHIáPXSBUFT r3FNPWFTEJTTPMWFEBOE dispersed oils r-PXQSFTTVSFESPQ r.FEJBDBOIPMEQFSDFOU

of its own weight, with no release of removed hydrocarbons

Applications

r(BTBOEPJMGBDJMJUJFT r-FJTVSFDPNNFSDJBMTIJQQJOH bilge water r4VSGBDFXBUFSSVOPGG USVDLTUPQT

BJSQPSUTQBSLJOHMPUT r"VUPTFSWJDFTUBUJPOT r.BDIJOFTIPQT

r*OEVTUSJBMQSPDFTTFT r'BDUPSJFTBOESFQBJSTIPQT r$BSBOEUSVDLXBTIFT

Installation

Certain applications may require pre-filtration.

Change-Out Frequency

Change-out frequency will depend on the oil burden in the application.

Because no appreciable increase in pressure drop is observed during service life, the filter must be changed when its adsorption capacity is exhausted.

Dimensions

-FOHUI

Outside Diameter

$PSF*%

5FNQFSBUVSF-JNJU

'MPX3BUF

1SFTTVSF%SPQ BUHQN

JO NN

' $

HQN -NJO

QTJ CBS

.BUFSJBM4QFDJàDBUJPOT

End Caps

Center Core

Outer Net

.FEJB

Area

Weight

Chemical Notification #

PVC Plastisol

Natural Polypropylene

Polyethylene

.PEJàFE$FMMVMPTF

TRGU TRN

MCT LH

[FSP

OAC-20BB

0JM"ETPSCJOH$BSUSJEHF

4QFDJmD(SBWJUZ7JTDPTJUZBOE8FJHIUTPG$PNNPO-JRVJET

-JRVJE

4QFDJmD

(SBWJUZ

7JTDPTJUZ

8FJHIU

MCTHBMMPO

Miscellaneous Liquids

Water

(BTPMJOF

+FU'VFM

Kerosene

Turpentine

7BSOJTI4QBS

Fuel Oil and Diesel Oil

/P'VFM0JM

/P"'VFM0JM

/P#'VFM0JM

/P'VFM0JM

/P%%JFTFM'VFM

1.0

m m m m

0.9

400

120 m m m

/P%%JFTFM'VFM

Crankcase Oil - Automobile Lubricating Oils

4"&

Transmission Oils - Automobile Transmission Gear Lubricants

4"&

12000

-JRVJE

Other Oils

Castor Oil

Chinawood

Coconut

Cod

Corn

$PUUPO4FFE

Cylinder

/BWZ/P'VFM

(BT

*OTVMBUJOH-BSE

-JOTFFE

3BX.FOIBEEFO

/FBUT'PPU

Olive

Palm

Peanut

Quencing

3BQF4FFE

3PTJO

3PTJO 8PPE

4FTBNF

4PZB#FBO

4QFSN

5VSCJOF -JHIU

5VSCJOF )FBWZ

Whale

4QFDJmD

(SBWJUZ

0.924

m m

1.0

0.924

0.92

0.919

1.09

0.91

7JTDPTJUZ

9000

14000

1100

24000

1000

900

Extreme

Viscose

1400

8FJHIU

MCTHBMMPO

m m m m m

9.1

1FSGPSNBODF

The Oil Adsorbing cartridge typically reduces hydrocarbon contamination up to 90-95 percent in a single pass. Lower outlet levels of hydrocarbons can be achieved by connecting cartridges in series. Higher flow rates also can be achieved by connecting cartridges in parallel.

Hydrocarbon-adsorbing capacity:

5IFDBSUSJEHFNFEJBIBTUIFQPUFOUJBMUPSFNPWFVQUPHSBNT MCTIZESPDBSCPO contaminant. On this basis, the table below provides expected life data in hours or gallons at several contaminant levels

CBTFEPOBHQNáPXSBUFQFSYDBSUSJEHF

)ZESPDBSCPO

$PODFOUSBUJPO

11.

100

1000

)ZESPDBSCPO

$PODFOUSBUJPO

CZXFJHIU

0.001

0.01

0.1

)ZESPDBSCPO

3FNPWBMQFS.JOVUF

HSBNT

&TUJNBUF-JGFJO

)PVST

(BMMPOT'MVJE

5SFBUFE

&TUJNBUFE$PTUQFS

(BMMPOPG5SFBUFE

'MVJE

0.001

0.01

0.11

1.1

NOTE:

0QFSBUJOHáPXXJMMWBSZCBTFEPOBQQMJDBUJPOTUZQFPGQPMMVUBOUTáPXSBUFTBOEMFWFMPGDPOUBNJOBUJPO

DISPOSAL:

4BGFBOEBDDFQUBCMFNFUIPEUPNFFUBMMMPDBMBOE&1"SFHVMBUJPOTJTSFDPNNFOEFE&OEVTFSJTSFTQPOTJCMFGPSTBGFEJTQPTBMPGVTFEDBSUSJEHFBUVTFSTDPTU$POTVMUGBDUPSZGPS additional information.

¥1FOUBJS'JMUSBUJPO*OD

*OEJBOB"WFOVFr10#PYr4IFCPZHBO8JTDPOTJO

$VTUPNFS4FSWJDFr'BYrTVQQPSUTQFDJBMJTU!QFOUFLàMUSBUJPODPN

*OUFSOBUJPOBMr'BYrJOUFSOBUJPOBM!QFOUFLàMUSBUJPODPN

XXXQFOUFLàMUSBUJPODPN 1SJOUFEJO64".3

P SERIES SPUN-BONDED

POLYPROPYLENE CARTRIDGES

t.BOVGBDUVSFEGSPNQVSFQPMZQSPQZMFOF

t%FTJHOFEGPSQVSJUZBOEDIFNJDBMDPNQBUJCJMJUZ t4QVOmCFSTGPSNBUSVFHSBEJFOUEFOTJUZGSPNPVUFSUPJOOFSTVSGBDFT

P Series cartridges are manufactured from pure 100% polypropylene fibers. The fibers have been carefully spun together to form a true gradient density from outer to inner surfaces.

P Series cartridges are designed for purity. They will not impart taste, odor or color to the liquid being filtered when used within the recommended temperature limit.

Additionally, the polypropylene construction provides superior chemical resistance and is not prone to bacterial attack.

The coreless strength of the cartridges is achieved by sintering the many fibers into a solid matrix.

P Series cartridges are available in a wide array of sizes and micron ratings to accommodate all of your filtration needs.

P SERIES

4QVO#POEFE1PMZQSPQZMFOF$BSUSJEHFT

3%2

)%3

3%2)%3

*>ÀÌViÊ-âiÊVÀÃ®

$BSUSJEHF4QFDJmDBUJPOTBOE1FSGPSNBODF%BUB

.PEFM

.BYJNVN%JNFOTJPOT

P5-478

P25

P1-20

P5-20

P25-20

P1-30

P5-30

2 3 ⁄

" x 4 7 ⁄

" (60 mm x 124 mm)

⁄

" x 9

⁄

" (60 mm x 248 mm)

2 3 ⁄

" x 9 3 ⁄

" (60 mm x 248 mm)

2 3 ⁄

" x 9 3 ⁄

" (60 mm x 248 mm)

2 3 ⁄

" x 20" (60 mm x 508 mm)

2 3 ⁄

" x 20" (60 mm x 508 mm)

⁄

" x 20" (60 mm x 508 mm)

⁄

" x 30" (60 mm x 762 mm)

2 3 ⁄

" x 30" (60 mm x 762 mm)

#BTFEPONBOVGBDUVSFShTJOUFSOBMUFTUJOH

.JDSPO3BUJOH OPNJOBM

.BUFSJBMTPG$POTUSVDUJPO

Filter Media

Temperature Rating

Polypropylene Fibers

40–145ºF (4.4–62.8ºC)

WARNING: Do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the system.

*OJUJBMå1 QTJ

!'MPX3BUF HQN

0.3 psi @ 2 gpm (<0.1 bar @ 7.6 Lpm)

0.6 psi @ 5 gpm (<0.1 bar @ 19 Lpm)

0.2 psi @ 5 gpm (<0.1 bar @ 19 Lpm)

0.6 psi @ 10 gpm (<0.1 bar @ 38 Lpm)

0.2 psi @ 10 gpm (<0.1 bar @ 38 Lpm)

0.5 psi @ 10 gpm (<0.1 bar @ 38 Lpm)

0.2 psi @ 10 gpm (<0.1 bar @ 38 Lpm)

The P1, P5, P1-20, and P5-20 is Tested and Certiﬁed by NSF International to

NSF/ANSI Standard 42 for material requirements only.

*OEJBOB"WFOVFr10#PYr4IFCPZHBO8JTDPOTJO

$VTUPNFS4FSWJDFr'BYrTVQQPSUTQFDJBMJTU!QFOUFLàMUSBUJPODPN

*OUFSOBUJPOBMr'BYrJOUFSOBUJPOBM!QFOUFLàMUSBUJPODPN www.pentekfiltration.com Printed in USA MR06 310060

PCC212

PCC218

Pcc series HeXaMetaPHOsPHate crYstaL cartridges

• Hexametaphosphate crystals help prevent Lime* and scale* deposits

• effective for treating corrosion and iron problems

• three unique designs to fit multiple applications

• Variety of media volumes and flow rates

• Manufactured with all Fda grade materials

PCC Series filter cartridges contain food-grade hexametaphosphate that dissolve slowly in water to inhibit scale and rust build-up.

These cartridges are available in four feeder sizes with variable volumes of phosphate crystals. All materials are FDA grade.

They are effective for treating scale, corrosion and iron problems for up to six months at various flow rates and feed concentrations.

The PCC212 and PCC218 cartridges are designed to fit

PENTEK #10 Standard or Slim

Line

filter housings. The PCC-1 cartridge is designed to fit in #10

Standard filters only.

The PCC-106 is an insert element that is placed in the center core of the cartridge. It is designed for use with standard 10" and 20" radial flow, sediment and carbon block double open-ended filter cartridges.

This type of treatment is recommended for use with ice machines, coffee and vending machines, food service equipment, water heaters, air conditioning equipment and many other types of water processing equipment.

PCC-1

PCC-106

Pcc series

Hexametaphosphate crystal cartridges

SCALE:

Hardness particles are kept separated so they cannot precipitate and form deposits when heated. Maximum hardness

15 gpg.

CORROSION:

A protective coating is formed on all metal surfaces, safeguarding against acidity/alkalinity, hardness, chloride and other factors which effect the corrosion of water equipment and pipes. pH range 6.5 – 9.0.

IRON:

Dissolved iron, up to 1 ppm, is kept suspended in solution

(sequestered), preventing dissolved iron from precipitating, which would cause staining and discoloration.

cartridge specifications and Performance data

Model Maximum dimensions initial ∆P (psi) @ Flow rate (gpm)

PCC-1

PCC-106

PCC212

PCC218

⁄

" x 9

⁄

" (73 mm x 244 mm)

⁄

" x 5

⁄

" (27 mm x 138 mm)

⁄

" x 9

⁄

" (67 mm x 248 mm)

⁄

" x 9

⁄

" (67 mm x 248 mm)

Up to 5 gpm (19 Lpm)

1 to 1.5 gpm (4 to 6 Lpm) for insertion in center core of open core cartridges

1 to 1.5 gpm (4 to 6 Lpm)

1.5 to 2.5 gpm (6 to 10 Lpm)

Materials of construction

Filter Media

Food Grade Polyphosphate

Shell

Polypropylene

Post-Filter

Gaskets

Polypropylene

Buna-N (PCC212 & PCC218)

Temperature Rating

40–100ºF (4.4–37.8ºC)

CAUTION:

Eye irritant. Contains sodium calcium hexametaphosphate. Avoid contact with eyes. In case of eye contact, flush with water for 15 minutes, get medical attention. Keep out of reach of children.

WARNING:

For drinking water applications, do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the system.

NOTE:

PCC212 and PCC218 cartridges are not recommended for main line water applications with flow rates exceeding 3.0 gpm (11.4 lpm).

NOTE:

With steamers, the water should be flushed daily.

CAUTION:

Do not use this cartridge on water that will be carbonated.

502 Indiana Avenue • P.O. Box 1047 • Sheboygan, Wisconsin 53082-1047

Customer Service: 800.645.0267 • Fax: 888.203.7361 • [email protected]

International: 920.457.9435 • Fax: 920.457.2417 • [email protected]

www.pentekfiltration.com Printed in USA MR06 310085

BBF1-20MB

PCF SERIES MIXED BED DEIONIZATION CARTRIDGES

t%FTJHOFEGPSEFJPOJ[JOHXBUFSVQUPNFHPINT t"MMNBUFSJBMTBOEDPOTUSVDUJPOBSF'%"DPNQMJBOU t5ISFFTJ[FTBOEDBQBDJUJFT

PCF1-10MB

PCF1-20MB

PCF Series filter cartridges have been developed in response to the requirements for deionized water in many industries.

They are manufactured using an

FDA-compliant resin that has been subjected to additional postproduction steps to minimize the total organic carbon (TOC) level.

These high-capacity, semi-conductorgrade resin cartridges are ideal for use in pharmaceutical and medical laboratories, cosmetics, and circuit board printing applications.

PCF Series cartridges are available in three sizes, flow rates and capacities. They are convenient and cost effective for many applications where low levels of total organic carbon (TOC) and total dissolved solids (TDS) are required.

Applications:

r$JSDVJUCPBSEQSJOUJOH r1IBSNBDFVUJDBMVTF r4UFBNBOEIVNJEJàDBUJPO r$PTNFUJDT r4UFBNQSPDFTTPST r)VNJEJàDBUJPOTZTUFNT r3FDJSDVMBUJOHDPPMJOHUPXFST r1PXFSHFOFSBUJOHFRVJQNFOU r.FEJDBMMBCPSBUPSZVTF

r-BTFST r+FUXBUFSTQSBZFST r#PJMFSNBLFVQXBUFS

PCF SERIES

.JYFE#FE%FJPOJ[BUJPO$BSUSJEHFT

5ZQJDBM$BSUSJEHF1SPQFSUJFTBOE

$IBSBDUFSJTUJDT

FUNCTION STRUCTURE:

$BUJPO 340)

"OJPO "3/ $) $)0)0)

PHYSICAL FORM:

.PJTUTQIFSJDBMCFBE

IONIC FORM:

)0)

PERCENT CONVERSION:

)ZESPHFO

)ZESPYJEF

NJOJNVN

1$'

##'

'MPX3BUFoHQN -QN

$BSUSJEHF4QFDJmDBUJPOTBOE1FSGPSNBODF%BUB

.PEFM

.BYJNVN%JNFOTJPOT

1$'.# 2 2 ⁄

" x 9 3 ⁄

" (68 mm x 248 mm)

$BQBDJUZ(SBJOT

NH5%4BT$B$0

)

270 (17,500)

1$'.#

##'.#

2 2 ⁄

" x 20" (68 mm x 508 mm)

⁄

" x 20" (114 mm x 508 mm)

600 (38,800)

1850 (120,000)

*OJUJBMå1 QTJ

!'MPX3BUF HQN

1.5 psi @ 0.25 gpm

CBS!-QN

3.4 psi @ 0.50 gpm

CBS!-QN

1.10 psi @ 1.25 gpm

CBS!-QN

4VHHFTUFE'MPX3BUF

HQN -QN

.BUFSJBMTPG$POTUSVDUJPO

Filter Media

End Caps

.JYFE#FE%*3FTJOT

Polypropylene

Shell

Pre-Filter

Polypropylene

Post-Filter

Gaskets

Polypropylene

#VOB/

Temperature Rating

40–100ºF (4.4–37.8ºC)

WARNING:

'PSESJOLJOHXBUFSBQQMJDBUJPOTEPOPUVTFXJUIXBUFSUIBUJTNJDSPCJPMPHJDBMMZVOTBGFPSPGVOLOPXORVBMJUZXJUIPVUBEFRVBUFEJTJOGFDUJPOCFGPSFPSBGUFSUIFVOJU

NOTE:

5IFBCPWFSFTJOEBUBJTCBTFEPOJOGPSNBUJPOPCUBJOFECZ1FOUBJS'JMUSBUJPO*OD5IJTEBUBEPFTOPUJNQMZBOZXBSSBOUZPSQFSGPSNBODFHVBSBOUFF8FSFDPNNFOEUIBUUIFVTFSEFUFSNJOF

QFSGPSNBODFCZUFTUJOHPOIJTPXOQSPDFTTJOHFRVJQNFOU8FBTTVNFOPMJBCJMJUZPSSFTQPOTJCJMJUZGPSQBUFOUJOGSJOHFNFOUSFTVMUJOHGSPNUIFVTFPGUIJTQSPEVDU

CAUTION:

Do not use cartridges on equipment that has an electric conductivity water level indicator.

¥1FOUBJS'JMUSBUJPO*OD

*OEJBOB"WFOVFr10#PYr4IFCPZHBO8JTDPOTJO

$VTUPNFS4FSWJDFr'BYrTVQQPSUTQFDJBMJTU!QFOUFLàMUSBUJPODPN

*OUFSOBUJPOBMr'BYrJOUFSOBUJPOBM!QFOUFLàMUSBUJPODPN

XXXQFOUFLàMUSBUJPODPN 1SJOUFEJO64"/0

POLYDEPTH

SERIES POLYPROPYLENE CARTRIDGE

t5IFSNBMMZCPOEFEQPMZQSPQZMFOFNJDSPmCFSDPOTUSVDUJPOGPSIJHIFSmMUSBUJPOFGmDJFODZ t$POTJTUFOUnPXSBUFBOETVQFSJPSmMUSBUJPOQFSGPSNBODF t"WBJMBCMFJOBXJEFSBOHFPGNJDSPOSBUJOHTBOEMFOHUIT t8JMMOPUJNQBSUUBTUFPEPSPSDPMPSUPXBUFSCFJOHmMUFSFE t*EFBMGPSBXJEFWBSJFUZPGJOEVTUSJBMmMUSBUJPO

The POLYDEPTH ® filtration cartridge is constructed of thermally bonded polypropylene microfibers to ensure high efficiency. The filter incorporates a rigid polypropylene center core for increased collapse strength and durability. This thermal bonded micro-fiber construction has minimal fiber release, consistent flow rate and superior filtration performance. It also is not brittle or prone to breakage problems like resin-bonded cartridges.

Unique micro-grooves provide added surface area. The polydepth cartridge will not impart taste, odor or color to the liquid being filtered, which makes it ideal for food and beverage applications. The recommended temperature limit of

40ºF to 175ºF (4.4ºC to 79.4ºC) allows it to be used in many hot water applications. Additionally, the polypropylene construction provides superior chemical resistance and is not prone to bacterial attack.

Available in different lengths from

⁄

" up to 40". Unlike competitive cartridges, the longer lengths are not manufactured by gluing shorter cartridges together. They are continuous cartridges that cannot separate during use and do not sacrifice filtering surface area. POLYDEPTH cartridges are available in various micron ratings including 1-, 5-, 10-, 25-, and 50microns.

POLYDEPTH

SERIES

1PMZQSPQZMFOF$BSUSJEHFT

NJDS

1BSUJDMF4J[F .JDSPOT

$BSUSJEHF4QFDJmDBUJPOTBOE1FSGPSNBODF%BUB

.PEFM

.BYJNVN%JNFOTJPOT

PD-1-934

PD-5-934

PD-10-934

PD-25-934

PD-50-934

PD-1-20

PD-5-20

PD-10-20

PD-25-20

PD-50-20

PD-1-30

PD-5-30

PD-25-30

PD-1-40

PD-5-40

PD-25-40

2 1 ⁄

" x 9 7 ⁄

" (64 mm x 251 mm)

⁄

" x 9

⁄

" (64 mm x 251 mm)

2 1 ⁄

" x 9 7 ⁄

" (64 mm x 251 mm)

2 1 ⁄

" x 9 7 ⁄

" (64 mm x 251 mm)

2 1 ⁄

" x 9 7 ⁄

" (64 mm x 251 mm)

⁄

" x 20" (64 mm x 510 mm)

2 1 ⁄

" x 20" (64 mm x 510 mm)

2 1 ⁄

" x 20" (64 mm x 510 mm)

2 1 ⁄

" x 20" (64 mm x 510 mm)

⁄

" x 20" (64 mm x 510 mm)

2 1 ⁄

" x 30" (64 mm x 763 mm)

2 1 ⁄

" x 30" (64 mm x 763 mm)

⁄

" x 30" (64 mm x 763 mm)

2 1 ⁄

" x 40" (64 mm x 1017 mm)

2 1 ⁄

" x 40" (64 mm x 1017 mm)

⁄

" x 40" (64 mm x 1017 mm)

/PU1FSGPSNBODF5FTUFEPS$FSUJmFECZ/4'

.JDSPO3BUJOH OPNJOBM

.BUFSJBMTPG$POTUSVDUJPO

Filter Media

Temperature Rating

Polypropylene

40–175ºF (4.4–79.4ºC)

WARNING: Do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the system.

*OJUJBMå1 QTJ

!'MPX3BUF HQN

<2 psi @ 2 gpm (<0.14 bar @ 7.6 Lpm)

<2 psi @ 5 gpm (<0.14 bar @ 19 Lpm)

<2 psi @ 7 gpm (<0.14 bar @ 26.5 Lpm)

<2 psi @ 9 gpm (<0.14 bar @ 34 Lpm)

The PD-1-934, PD-5-934, PD-10-934,

PD25-934, PD-50-934, PD-1-20, PD-5-20,

PD-10-20, PD25-20 and PD-50-20 are

Tested and Certiﬁed by NSF International to NSF/ANSI Standard 42 for material requirements only.

¥1FOUBJS'JMUSBUJPO*OD

*OEJBOB"WFOVFr10#PYr4IFCPZHBO8JTDPOTJO

$VTUPNFS4FSWJDFr'BYrTVQQPSUTQFDJBMJTU!QFOUFLàMUSBUJPODPN

*OUFSOBUJPOBMr'BYrJOUFSOBUJPOBM!QFOUFLàMUSBUJPODPN

XXXQFOUFLàMUSBUJPODPN 1SJOUFEJO64".3

R SERIES PLEATED POLYESTER CARTRIDGES

t1MFBUFEEFTJHONBYJNJ[FTEJSUIPMEJOHDBQBDJUZ t7FSTBUJMFBOESFVTBCMFBMMPXJOHGPSBWBSJFUZPGVTFT t%VSBCMFQPMZFTUFSNFEJBJTCBDUFSJBBOEDIFNJDBMSFTJTUBOU t/PNJOBMNJDSPOSBUJOH 3BOEOPNJOBMNJDSPOSBUJOH 3

R30-20

R50

R50BB

R30-20BB

R30-478

R Series cartridges are manufactured from a durable, non-woven and reusable polyester fabric that is suitable for a wide range of filtration uses.

The media is pleated around a polypropylene core for added strength and the ends are immersed in a thermo-setting vinyl plastisol.

Embedding and sealing each end of the pleat in this fashion fuses the three components together forming a unified end cap and gasket. The overlap seam is sonically welded to reduce internal bypass improving filtration efficiency.

The standard 9

⁄

” length cartridge has more than four square feet of polyester fabric, while the larger

Big Blue ® version has more than 16 square feet. The media is pleated to maximize dirt-holding capacity and extend the time period between changes or cleaning.

R Series cartridges are resistant to both bacteria and chemical attack making them suitable for a variety of residential, commercial and industrial applications.

R SERIES

1MFBUFE1PMZFTUFS$BSUSJEHFT

100

1.0

(0.069)

0.8

(0.062)

R30-478

R30

R30-BB

R50

R50-BB

0.6

(0.041)

0.4

(0.028)

R50-BB

R30-BB

R30

R50

R30-478

0.2

(0.014)

Particle Size (Microns)

$BSUSJEHF4QFDJmDBUJPOTBOE1FSGPSNBODF%BUB

.PEFM

.BYJNVN%JNFOTJPOT

R30

R50

R30-20

2 5 ⁄ " x 4 ⁄ NNYNN

2 5 ⁄ " x 9 3 ⁄

NNYNN

2 5 ⁄ " x 9 3 ⁄

NNYNN

2 5 ⁄ Y NNYNN

R30-BB

R50-BB

4 1 ⁄

" x 9 3 ⁄

NNYNN

4 1 ⁄

" x 9 3 ⁄

NNYNN

R30-20BB 4

⁄

Y NNYNN

#BTFEPONBOVGBDUVSFShTJOUFSOBMUFTUJOH

(3.8)

(7.6)

(11.4)

(18.9)

(22.7)

Flow Rate – gpm (Lpm)

(30.3)

(37.9)

.JDSPO3BUJOH OPNJOBM

.BUFSJBMTPG$POTUSVDUJPO

Filter Media

Endcaps

/PO8PWFO1PMZFTUFS

7JOZM1MBTUJTPM

Core

Temperature Rating

1PMZQSPQZMFOF m' m$

WARNING: Do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the system.

*OJUJBMå1 QTJ

!'MPX3BUF HQN

QTJ!HQN CBS!-QN

¥1FOUBJS'JMUSBUJPO*OD

*OEJBOB"WFOVFr10#PYr4IFCPZHBO8JTDPOTJO

$VTUPNFS4FSWJDFr'BYrTVQQPSUTQFDJBMJTU!QFOUFLàMUSBUJPODPN

*OUFSOBUJPOBMr'BYrJOUFSOBUJPOBM!QFOUFLàMUSBUJPODPN

XXXQFOUFLàMUSBUJPODPN 1SJOUFEJO64".:

S1 SERIES PLEATED CELLULOSE CARTRIDGES

t1MFBUFEEFTJHONBYJNJ[FTEJSUIPMEJOHDBQBDJUZ t%FTJHOFEGPSHFOFSBMXBUFSmMUSBUJPOQVSQPTFT t3FDPNNFOEFEGPSDIMPSJOBUFEXBUFSTVQQMJFT t&DPOPNJDBMMZQSJDFE t/PNJOBMNJDSPOSBUJOH

S1 Series cartridges are manufactured from a pleated cellulose media and are designed for general water filtration purposes.

The media is pleated around a polypropylene core for added strength and the ends are immersed in a thermo-setting vinyl plastisol.

Embedding and sealing each end of the pleat in this fashion fuses the three components together forming a unified end cap and gasket.

The overlap seam is sonically welded to reduce bypass, improving filtration efficiency.

S1 Series cartridges are economically priced and highly effective at reducing sediment particles down to

20 microns in size.

S1 SERIES

1MFBUFE$FMMVMPTF$BSUSJEHFT

100

TRIDGES

-BB CAR

S1 S

AND

ARD CAR

TRIDGES

Particle Size (Microns)

'MPX3BUFoHQN -QN

$BSUSJEHF4QFDJmDBUJPOTBOE1FSGPSNBODF%BUB

.PEFM

.BYJNVN%JNFOTJPOT

.JDSPO3BUJOH

OPNJOBM

S1 2

⁄

" x 9

⁄

" (67 mm x 248 mm) 20

*OJUJBMå1 QTJ

!'MPX3BUF HQN

2.4 psi @ 10 gpm (0.17 bar @ 38 Lpm)

4VSGBDF"SFB

580 in.

2 (0.38 m 2 )

3FDPNNFOEFE

'MPX3BUF

12 gpm (45 Lpm)

S1-20

S1-BB

S1-20BB

2 5 ⁄

" x 20" (67 mm x 508 mm)

⁄

" x 9

⁄

" (114 mm x 248 mm)

4 1 ⁄

" x 20" (114 mm x 508 mm)

0.8 psi @ 10 gpm (0.06 bar @ 38 Lpm) 1110 in.

2 (0.72 m 2 )

1.2 psi @ 10 gpm (0.08 bar @ 38 Lpm) 2070 in.

2 (1.34 m 2 )

1.2 psi @ 10 gpm (0.08 bar @ 38 Lpm) 4280 in.

2 (2.77 m 2 )

15 gpm (57 Lpm)

20 gpm (76 Lpm)

35 gpm (132 Lpm)

.BUFSJBMTPG$POTUSVDUJPO

Filter Media

End Caps

Resin-Impregnated Cellulose

Vinyl Plastisol

Core

Temperature Rating

Polypropylene

40–145ºF (4.4–62.8ºC)

NOTE: S1-BB and S1-20BB are for use in 10" and 20" Big Blue ® housings and BBFS systems only.

NOTE: Big Blue (BB) is a registered trademark of Pentair Filtration, Inc.

WARNING: Do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the system.

*OEJBOB"WFOVFr10#PYr4IFCPZHBO8JTDPOTJO

$VTUPNFS4FSWJDFr'BYrTVQQPSUTQFDJBMJTU!QFOUFLàMUSBUJPODPN

*OUFSOBUJPOBMr'BYrJOUFSOBUJPOBM!QFOUFLàMUSBUJPODPN www.pentekfiltration.com Printed in USA JE08 310059

WS-20BB

Ws series Water sOFteNer cartridges

• Manufactured with Fda grade softener resin

• available in a variety of sizes for multiple applications

• Utilize single use resin technologies for maximum life grains (caco

) capacity

• sodium form

WS Series cartridges are designed to allow optimal contact between water and resin surfaces, ensuring maximum ion exchange. The internal expansion pad minimizes channeling, while the post filter eliminates any potential for bypass.

Designed for low water usage, these units will easily deliver softened product water through the use of

FDA-grade sodium based, nonsolvent rinsed softening resin. The cartridge style design provides a convenient solution for delivering softened water to protect sensitive water delivery equipment.

WS Series cartridges are available in three sizes for use in PENTEK’s

SlimLine

, Standard, and Big Blue

Series filter housings. Properly sized, these units can effectively treat water in applications desiring low hardness and scale deposits with capacity ranging between 750 to

4,500 grains.

PENTEK’s water softening cartridges provide superior performance and outstanding protection for medical equipment, coffee and espresso appliances, low volume beverage and commercial food service machines.

WS-10

WS-20

Ws series

Water softening cartridges

84##

'MPX3BUFoHQN -QN cartridge specifications and Performance data

Model dimensions

WS-10

WS-20

WS-20BB

⁄

" x 9

⁄

" (67 mm x 248 mm)

⁄

" x 20" (67 mm x 508 mm)

⁄

" x 20" (114 mm x 508 mm)

recommended Flow rates

0.50 gpm (1.9 Lpm)

0.75 gpm (2.8 Lpm)

2.0 gpm (8.5 Lpm)

capacity (grains as cacO

)

750

1500

4500

Materials of construction

Filter Media

Cation, sodium-form resin,

20 x 40 mesh, R-SO3-Na+

End Caps

Pre-Filter

Post-Filter

Gaskets

Polypropylene

Buna-N

Temperature Rating

100ºF (37.8ºC)

WARNING:

For drinking water applications, do not use where the water is microbiologically unsafe or with water of unknown quality without adequate disinfection before or after the system.

502 Indiana Avenue • P.O. Box 1047 • Sheboygan, Wisconsin 53082-1047

Customer Service: 800.645.0267 • Fax: 888.203.7361 • [email protected]

International: 920.457.9435 • Fax: 920.457.2417 • [email protected]

www.pentekfiltration.com Printed in USA MR06 310082

SPECIFICATIONS AND PERFORMANCE

.BUFSJBMTPG$POTUSVDUJPO

Membrane:

Polyethersulfone

Membrane Assembly:

Polystyrene, epoxy resin

Carbon Pre-Filter:

.(.$#XJUI'JCSFEZOF ™ technology contains activated carbon with synthetic Polymeric fibers and binders

O-ring Seals:

EPDM

End Caps:

Top:

Netting:

Bottom: Polyolefin (MG-10MCB only)

3FDPNNFOEFE0QFSBUJOH$POEJUJPOT

Water Temperature Range:

40-140 q

' $

Pressure Differential:

88 psi (6.1 bar), max.

Storage Temperature Range:

35-104 q

' q

pH Range:

2-12

Operating Pressure Range:

Water Turbidity:

5-88 psi (0.35-6.1 bar), max.

< 1 NTU

Bacteria Reduction:

-PHDIBMMFOHFE

Organism:

Brevundimonas diminuta

(0.2 micron in size).

Method:

.PEJàFE64&1"(VJEF4UBOEBSEBOE1SPUPDPMGPS8BUFS1VSJàFST

Cyst Reduction:

-PHDIBMMFOHFEXJUINJDSPTQIFSFT

Method:

/4'"/4*4UBOEBSETVSSPHBUFDZTUQSPDFEVSFVTJOHNJDSPO

3FDPNNFOEFE'MPX3BUF

MG-10MCB 1 gpm

MG-10T 3 gpm

*OJUJBMå1 QTJ!'MPX3BUF HQN

MG-10MCB

MG-10T

QTJE!HQN CBS!MQN

13 psid @ 3 gpm (0.9 bar @ 11.4 lpm)

&TUJNBUFE$BQBDJUJFT

MG-10MCB

MG-10T

HBMMPOT -

** Capacities may vary depending on local water quality, type of pre-filtration and acceptable minimum flow rate.

WARNING: Do not use on water that may be contaminated by untreated surface water, water that may be contaminated by human or animal sewage or other wastewater. These cartridges are not intended for reducing pathogenic (disease-causing) virus particles, if present in the water, to below safe levels.

Note: These cartridges are intended for use on visually clear drinking water that meets all other public health standards.

Note: Product features are subject to change by Pentair Water at any time without notice.

Not certified for sale in California, Iowa, Massachusetts and Wisconsin.

MICROGUARD™ SERIES

.JDSPmMUFS.FNCSBOF$BSUSJEHFT

/FU1SFTTVSF%SPQWT'MPX3BUF XBUFS

100

(6.9)

(5.2)

(3.4)

.(.$#

.(5

0 2.0 4.0 6.0 8.0 10

'MPX3BUFHQN -NJO

$BSUSJEHF4QFDJmDBUJPOTBOE1SPEVDU*OGPSNBUJPO

.PEFM

MG-10MCB

MG-10T

%FTDSJQUJPO

$BSCPO#MPDL

Membrane

Triple Element

(membrane only

)

.BYJNVN

-FOHUI

(261.18 mm)

(261.47 mm)

.BYJNVN

%JBNFUFS

(73 mm)

3.0

(76 mm)

.JDSPO

3BUJOH

0.15

absolute rating

0.15

absolute rating

/PUFT

'JUT

PENTEK Standard and Slimline

3G Housing

'JUT PENTEK Standard and Slimline

3G Housing

3FDPNNFOEFEQSFàMUSBUJPOGPSUIF.(5NFNCSBOFPOMZDBSUSJEHFT

− HEP-1-3.1-10 High Efficiency Pleated Cartridge

− EP-10 Carbon Block Cartridge

− CBC-10 Carbon Block Cartridge

− PD-1-934 Polydepth Cartridge

Not certified for sale in California, Iowa, Massachusetts and Wisconsin.

¥1FOUBJS'JMUSBUJPO*OD

*OEJBOB"WFOVFr10#PYr4IFCPZHBO8JTDPOTJO

$VTUPNFS4FSWJDFr'BYrDVTUPNFSTFSWJDF!QFOUFLàMUSBUJPODPN

*OUFSOBUJPOBMr'BYrJOUFSOBUJPOBM!QFOUFLàMUSBUJPODPN www.pentekfiltration.com

Printed in USA JA06 310905

BP, BPHE AND BN SERIES FILTER BAGS

t5IFSNBMMZXFMEFEVOJRVFEFTJHOSFTVMUTJODPOTJTUFOUmMUSBUJPOFGmDJFODJFT t4FNJSJHJEDZMJOESJDBMEFTJHOJTFBTJMZDSVTIFEBOEJODJOFSBUFE t)JHIFSQSPEVDUJWJUZoGBTUFSCBHiDIBOHFPVUTw

BP-420

BN-420

BP-410

BHPE-420

BN-410

BHPE-410

Polypropylene bags are compatible with a broad range of corrosive fluids including organic solvents, oils, acids, alkalis and microorganisms.

BP Series (Polypropylene Felt) Bags

An assortment of filtration ratings is offered – from 1 to 200 microns

– to comply with any filtration requirement.

The bags are manufactured from felt due to its high solids loading capabilities, in comparison to similar mesh fabrics. The media is created by needle-punching two layers of synthetic fibers together in a supporting scrim. A glazed finish, created by melting the outermost surface fibers, is used to produce a bond that reduces the possibility of migration.

BPHE Series (High Efficiency) Bags

High efficiency bags are offered for those critical applications when high efficiency combined with high dirt-holding capacity is required. Polypropylene materials are processed into microfibers with diameters of 1-10 microns or more.

These fibers are converted into filter material. Microfiber media are covered with spun-bonded polypropylene.

BN Series (Strainer) Bags

Woven monofilment materials are offered in nylon with micron ratings of 50-800 and efficiencies from 75 to 95 percent. The materials are cleanable and reusable.

BP, BPHE, & BN SERIES

'JMUFS#BHT

)JHI&GmDJFODZ#BHT

NJDSPOT

1PMZQSPQZMFOF'FMU#BHT

4.5

100

8.3

'MPX3BUFPG8BUFS $14!'HQN

200

16.6

400

27.7

800

50.0

Viscosity (cps)

1000 1500

56.2

77.2

Correction Factor

2000

113.6

4000

161.0

6000

250.0

8000

325.0

10000

430.0

'MPX3BUFPG8BUFS $14!'HQN

$BSUSJEHF4QFDJmDBUJPOTBOE1FSGPSNBODF%BUB

.PEFM

%JNFOTJPOT

BP-410

BP-420

4" x 8 5 ⁄

" (102 mm x 218 mm)

4" x 18" (102 mm x 457 mm)

BPHE-410 4" x 8 5 ⁄

" (102 mm x 218 mm)

BPHE-420 4" x 18" (102 mm x 457 mm)

BN-410

BN-420

4" x 8 5 ⁄

" (102 mm x 218 mm)

4" x 18" (102 mm x 457 mm)

'JMUFS.FEJB

.JDSPO3BUJOH

Glazed Polypropylene Felt

Polypropylene microfibers with spun-bonded polypropylene covers

Nylon monofilament mesh

1, 5, 10, 25, 50, 100, 200

1, 5, 10, 25, 50, 75, 100

50, 100, 150, 200, 250, 300, 400, 600, 800

$BTF

2VBOUJUZ

Maximum Temperature

200ºF (93.3ºC)

See application literature for housing rating.

WARNING:

For drinking water applications, do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the system.

NOTE:

This information is for general guidance. Users should test bag materials with media involved to determine compatibility.

CAUTION:

Protect against freezing to prevent cracking of the filter and water leakage.

*OEJBOB"WFOVFr10#PYr4IFCPZHBO8JTDPOTJO

$VTUPNFS4FSWJDFr'BYrTVQQPSUTQFDJBMJTU!QFOUFLàMUSBUJPODPN

*OUFSOBUJPOBMr'BYrJOUFSOBUJPOBM!QFOUFLàMUSBUJPODPN www.pentekfiltration.com Printed in USA MR06 310088

Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project