idatastart COM-IDS(RS)-BM1-EN Install Manual

The idatastart COM-IDS(RS)-BM1-EN is an advanced vehicle interface module designed to integrate seamlessly with your BMW or MINI vehicle. This compact and versatile device offers a range of features to enhance your car's security, convenience, and remote control capabilities. With the COM-IDS(RS)-BM1-EN, you can enjoy the benefits of remote start, keyless entry, trunk release, and more, all from the comfort of your existing OEM remote control. Additionally, the module provides data immobilizer bypass, allowing you to seamlessly integrate an aftermarket remote start system into your vehicle.

PDF Download

Document

instaLL guiDe

COM-IDS(RS)-BM1-EN

Document numbeR

11866

Revision Date

20130723

FiRmwaRe

COM-IDS(RS)-BM1

haRDwaRe

ADS-BM1

accessoRies

PROGRAMMING CABLE ADS-USB (REQUIRED)

COMPATIBLE RF-KIT (OPTIONAL)

DRONE MOBILE DR-2000 (OPTIONAL)

FT-D100 (OPTIONAL)

notice

The manufacturer will accept no responsability for any electrical damage resulting from improper installation of this product, be that either damage to the vehicle itself or to the installed device. This device must be installed by a certified technician. Please review the Installation Guide carefully before beginning any work.

beFoRe instaLLation

1- Connect module to computer

2- Login to Weblink account

3- Flash firmware to module (module is not preloaded with firmware)

4- Use accessories accordingly (accessories are sold separately) compustar.idatalink.com

VEHICLE LIST - 1 OF 1

FEATURES

Page 2 oF 16

DOC.: #11866

• 20130723

NOTES

I This fi rmware covers Automatic Transmission

(AT) vehicles only.

1 Series PTS AT

3 Series PTS AT***

5 Series PTS AT

6 Series PTS AT

1M PTS AT

M3 PTS AT***

M5 PTS AT

08-13 1 • • • • • • • • •

06-11 1 • • • • • • • • •

05-10 1 • • • • • • • • •

11 1 • • • • • • • • •

08-12 1 • • • • • • • • •

06-10 1 • • • • • • • • •

M6 PTS AT

X1 PTS AT***

X5 PTS AT

X5 Diesel PTS AT

X5 M PTS AT

X6 PTS AT

X6 M PTS AT

Z4 PTS AT***

Clubman PTS AT***

06-10 1

12-13 1

08-13 1

10-13 1

08-13 1

10-13 1

•

09-13 1 • • • • • • • • •

08-13 1 • • • • • • • • •

Cooper PTS AT***

Cooper Convertible PTS AT***

07-13 1

08-13 1

•

Coupe PTS AT***

Roadster PTS AT***

* If equipped with a factory hood switch.

** If equipped with an electric E-brake and it is activated, vehicle will shudown when a door is opened during RS sequence.

*** If equipped with the Confort Access System, the door handles will not be functional during RS sequence.

12-13 1 • • • • • • • • •

• • • • •

• • •

•

• • • • •

•

• • • • • • • • •

• • • • • • • • • •

• • • • • •

• • • • •

•

BOX CONTENTS

MODULE

PROGRAMMING

BUTTON

LED 1

LED 2

EXPANSION PACK

XP LED 1 XP LED 2

ACCESSORIES (SOLD SEPARATELY)

PROGRAMMING CABLE (REQUIRED)

T-HARNESS 1

EXPANSION CABLE

BOX CONTENTS - 1 OF 1

10 PIN WHITE CONNECTOR

12 PIN BLACK CONNECTOR

AFTERMARKET HOOD SWITCH AND CABLE

Page 3 oF 16

DOC.: #11866

• 20130723

STICKER 1

STICKER 2

RF KIT (OPTIONAL)

COMPATIBLE MODELS ONLY

TELEMATICS DEVICE (OPTIONAL)

COMPATIBLE MODELS ONLY

imPoRtant technicaL note - 1 OF 1

instaLL viDeo gaLLeRY avaiLabLe onLine

Before installing this product, consult our Install Video Gallery and watch:

•

Vehicle Disassembly Procedure videos

•

Module Connection Procedures videos

•

Module Programming Procedures videos

Simply visit our forum and register at http://www.12voltdata.com/forum/viewtopic.php?f=340&t=9683&sid=a61772b486e4584ad6f058b171ffa425

Page 4 oF 16

DOC.: #11866

• 20130723

START vehicle. Verify all vehicle functionalities. If the vehicle displays error messages or any malfunction: stop the installation and service the vehicle.

Turn ignition to OFF position. Remove keyfob from keyport.

Verify all keyfob functionalities (Door Lock,

Door Unlock, Trunk Release and Comfort

Access System if equipped).

MODULE INSTALLATION PROCEDURE - 1 OF 1

Connect and secure every connector to the vehicle, as shown in STEP 1 of the WIRING

DIAGRAM.

WARNING: Any vehicle harness that is disconnected during installation, must be re-connected before performing any system tests. Failure to comply will result in vehicle displaying error messages. An OEM scantool will be required to clear the error messages.

START vehicle. Verify all vehicle functionalities.

Page 5 oF 16

DOC.: #11866

• 20130723

Connect the P connector to the module, as shown in STEP 3 of the WIRING DIAGRAM.

If required, connect a compatible RF Kit, as shown in STEP 4 of the WIRING DIAGRAM.

If required, connect a compatible Telematics

Device, as shown in STEP 4 of the WIRING

DIAGRAM.

Insert the expansion pack into module.

Use the EXPANSION CABLE to connect the A connector to the module and the O connector to the expansion pack.

Connect the module to the computer with the programming cable and ﬂ ash the module with the latest fi rmware. (F port)

WARNING: If the vehicle displays error messages or any malfunction, stop the installation, verify every connection and if the problem persists, call technical support.

Turn ignition to OFF position. Remove keyfob from keyport.

Connect the C connector to the module, as shown in STEP 2 of the WIRING DIAGRAM.

COM-IDS(RS)-BM1-EN

If the vehicle is not equipped with a factory hood switch, install an aftermarket hood switch as shown in STEP 4 of the WIRING

DIAGRAM.

Put sticker 1 on a clean and visible surface in the engine bay and put sticker 2 under the dashboard near the OBDII connector.

Module installation procedure completed.

compustar.idatalink.com

TYPE 1 - WIRING DIAGRAM - 1 OF 1

STEP 1:

CONNECT THE FOLLOWING TO THE VEHICLE

START THE VEHICLE WITH THE OEM KEYFOB

TO TEST THE CONNECTIONS

RELAY

Page 6 oF 16

DOC.: #11866

• 20130723

BRAKE SWITCH MODULE

WARNING

1-TO CONNECT THE MODULE: FOLLOW STEPS 1 TO 4

2-TO DISCONNECT THE MODULE: FOLLOW STEPS 4 TO 1

STEP 2:

CONNECT THE FOLLOWING TO THE MODULE

BLACK 20 PIN

STEP 3:

CONNECT THE FOLLOWING TO THE MODULE

WHITE 18 PIN

RELAY

07 GRAY/WHITE - HOOD STATUS (-) INPUT

08 GRAY/BLACK (NC)

BLACK 4 PIN - RF CABLE

BLUE 4 PIN - TELEMATIC CABLE

BRAKE HARNESS

COMFORT ACCESS SYSTEM MODULE

MINI: BEHIND INSTRUMENT PANEL, DRIVER SIDE

BMW: UNDER DASH, DRIVER SIDE

STEP 4:

CONNECT THE FOLLOWING IF REQUIRED

IF NOT EQUIPPED

WITH AN OEM HOOD SWITCH,

INSTALL AN AFTERMARKET HOOD SWITCH

B1 CONNECTOR

B2 HARNESS

C1 CONNECTOR

WARNING:

THESE CONNECTORS HAVE TWO

[2X] LOCKING MECHANISMS.

INSERT THE CONNECTOR IN ITS

HOUSING AND APPLY GENTLE

PRESSURE ON BOTH EXTREMITIES

TO SECURE THE CONNECTION.

(TWO AUDIBLE CLICKS WILL BE HEARD.)

C2 HARNESS

AFTERMARKET HOOD SWITCH (-)

COM-IDS(RS)-BM1-EN

RF KIT

TELEMATIC

compustar.idatalink.com

LED 1 is solid RED. Insert keyfob 1 into keyport.

Within 10 seconds, LED 1 will ﬂ ash GREEN once (1x).

Remove keyfob 1 from keyport.

LED 1 will turn solid RED. Wait 5 seconds.

Insert keyfob 1 into keyport.

MODULE PROGRAMMING PROCEDURE - 1 OF 1

Remove keyfob 1 from keyport.

WARNING: Follow steps 4, 3, 2 as shown in the wiring diagram to disconnect the module from the vehicle.

Connect module to computer and proceed with KLON programming.

WARNING: Follow steps 2, 3, 4 as shown in the wiring diagram to connect the module to the vehicle.

LED 1 will turn solid RED.

Insert keyfob 1 into keyport.

Within 10 seconds, LED 1 will ﬂ ash GREEN rapidly.

Page 7 oF 16

DOC.: #11866

• 20130723

LED 1 will turn solid GREEN for 2 seconds.

Remove keyfob 1 from keyport.

Module Programming Procedure completed.

compustar.idatalink.com



instaLLation checKList - 1 OF 2

Page 8 oF 16

DOC.: #11866

• 20130723

checKList

WARNING: Vehicle engine will start many times. Test in a well ventillated area.

Open driver door window for easy vehicle access.

Close all vehicle doors, hood and trunk.

Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle.

Question 1: Does the vehicle remote start?

YES: Go to step 5.

NO: The module doesn't detect OEM remote lock button from the vehicle communication network. Check all connection, repeat step 4 and call technical support if the problem persist.

Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down vehicle.

Question 2: Does the vehicle shut down?

YES: Go to step 6.

NO: Repeat step 5. If problem persists, push vehicle start button once [1x] to shut down the vehicle and call technical support.

Unlock and open driver door.

Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle.

Question 3: Does the vehicle remote start?

YES: The module does NOT detect the door signal from the vehicle communication network. Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down vehicle and call technical support.

NO: Go to step 8.

Open hood.

Question 4: Is the orange warning sticker "Sticker 1" placed under the hood?

YES: Leave hood open and go to step 9.

NO: Put the mandatory orange warning sticker "Sticker 1", leave hood open and go to step 9.

Close all doors.

Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle.

Question 5: Does the vehicle remote start?

YES: Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down vehicle. Go to Question 6.

NO: Go to step 11.

Question 6: Is the vehicle equipped with a factory hood switch? (Inside hood latch)

YES: The module does NOT detect the hood signal from the vehicle communication network. Call technical support.

NO: Install the mandatory hood switch included in the kit. Repeat installation checklist.

Close hood.

Enter vehicle. Do NOT press brake pedal.

Close all doors.

Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle.

Wait for the vehicle to start.

Press brake pedal.

Question 7: Does the vehicle shut down?

YES: Go to step 17.

NO: The module does NOT detect the brake pedal signal from the vehicle communication network. Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down vehicle and call technical support.

Apply parking brake.

Exit vehicle.

instaLLation checKList - 2 OF 2



checKList

Close all doors.

Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle.

Wait for the vehicle to start.

Question 8: Is the vehicle equipped with Comfort Access System ?

YES: For 1, 5, 6, X5, X6: Touch exterior driver door handle to unlock door using Comfort Access System. Within 45 seconds, go to step 22.

YES: For 3, X1, Z4, Mini: Press UNLOCK button once [1x] on the OEM keyfob. Within 45 seconds, go to step 22.

NO: Press UNLOCK button once [1x] on the OEM keyfob. Within 45 seconds, go to step 22.

Open driver door.

Question 9: Does the vehicle shut down?

YES: For Z4, X5, X6: Go to step 25.

YES: For 1, 3, 5, 6, X1: The module does NOT detect the parking brake signal or the unlock signal from the vehicle communication network. Call technical support.

NO: For Z4, X5, X6: The module does NOT detect the parking brake signal correctly from the vehicle communication network. Call technical support.

NO: For 1, 3, 5, 6, X1: Go to step 23.

Press and release brake pedal.

Push vehicle start button once [1x] to shut down the vehicle.

Installation checklist completed.

Page 9 oF 16

DOC.: #11866

• 20130723

NOTE: In Valet Mode, the Remote starter is not functional. Keyless entry, Lock and Unlock will remain functional. See RF kit user manual for alternate valet mode programming.

Insert keyfob into keyport.

VALET MODE PROGRAMMING PROCEDURE - 1 OF 1

Remove keyfob from keyport.

Valet Mode Programming Procedure completed.

To exit valet mode: repeat steps 1 to 6.

Time restriction. Complete next step within 7 seconds.

STOP ACC ON START

Cycle ignition ON fi ve times [5x OFF/ON] rapidly. Parking Light will ﬂ ash once [1x].

ENGINE

START

STOP

Wait, Parking Light will ﬂ ash twice [2x], pause for 1.5 second, then will ﬂ ash once [1x] to indicate that the valet mode is ON or twice [2x] to indicate that the valet mode is OFF.

STOP ACC ON START

Turn ignition to STOP position.

ENGINE

START

STOP

Page 10 oF 16

DOC.: #11866

• 20130723 compustar.idatalink.com

WARNING: Program aftermarket remotes before usage. A maximum of four [4x] aftermarket remotes per system.

Insert keyfob into keyport.

AFTERMARKET REMOTE PROGRAMMING PROCEDURE - 1 OF 1

Press once [1x] on LOCK button of aftermarket remote.

Parking Light will ﬂ ash once [1x].

Time restriction. Complete next step within 7 seconds.

To program additional remotes: repeat steps 5 to 7 using each additional remote.

STOP ACC ON START

Cycle ignition ON fi ve times [5x OFF/ON] rapidly.

ENGINE

START

STOP

Parking Light will ﬂ ash once [1x].

Time restriction. Complete next step within 5 seconds from previous step.

Wait, Parking Light will ﬂ ash twice [2x].

STOP ACC ON START

Turn ignition to STOP position.

ENGINE

START

STOP

Remove keyfob from keyport.

COM-IDS(RS)-BM1-EN

Page 11 oF 16

DOC.: #11866

• 20130723

Aftermarket Remote Programming Procedure completed.

compustar.idatalink.com

It is mandatory to exit the Module Navigation at the end of this procedure. Failure to exit the

Module Navigation will drain vehicle battery.

To exit the Module Navigation at any time:

Follow STEP 13.

Module must be programmed to the vehicle.

Use the Module Navigation Chart on the next page.

STOP ACC ON START

Set ignition to OFF position.

ENGINE

START

STOP

TO ACCESS THE MENUS: Press and hold programming button until LED 1 turns solid

GREEN.

[X]

IN THE MENUS: Press the programming button as many times as the menu number indicates. LED 1 will ﬂ ash GREEN an equal amount of times continuously.

MODULE NAVIGATION PROCEDURE - 1 OF 1

TO ACCESS THE OPTIONS: Press and hold programming button until LED 1 turns solid

RED.

[Y]

IN THE OPTIONS: Press the programming button as many times as the option number indicates. LED 1 will ﬂ ash RED an equal amount of times continuously.

TO ACCESS THE SETTINGS: Press and hold programming button until LED 1 turns solid

GREEN.

[Z]

LED 1 will ﬂash GREEN as many times as the current (or default) setting number, continuously.

[Z]

IN THE SETTINGS: Press the programming button as many times as necessary to access your setting. LED 1 will ﬂ ash GREEN an equal amount of times continuously.

To return to the MENUS: exit the Module

Navigation and redo the Module Navigation

Procedure.

COM-IDS(RS)-BM1-EN

Page 12 oF 16

DOC.: #11866

• 20130723

To save and return to the OPTIONS: Press and hold programming button until LED 1 turns solid RED.

[Y]

LED 1 will ﬂ ash RED as many times as the current option number continuously.

Configure every other setting and proceed to step 13.

MANDATORY: EXIT MODULE NAVIGATION.

Press and hold programming button for 7 seconds. LED 1 will ﬂ ash RED rapidly. Release programming button. LED 1 will turn OFF.

Module navigation completed.

Failure to exit the Module Navigation will drain vehicle battery.

compustar.idatalink.com

moDuLe navigation chaRt - 1 OF 1

Page 13 oF 16

DOC.: #11866

• 20130723

moDuLe navigation chaRt: notes

I Default settings are listed in bold.

II Make sure the option is covered on the vehicle before attempting to change the setting.

*Vehicle will shutdown when a door is opened.

01 CONFIGURATION

02-07 Technical Support only

COM-IDS(RS)-BM1-EN

DISARM/UNLOCK BEFORE START

RELOCK AFTER START

RELOCK AFTER SHUTDOWN

FORCE UNLOCK ALL ON FIRST PRESS

TAKEOVER

SECURE TAKEOVER DELAY

FACTORY KEYLESS RS SEQUENCE

MODULE RUN TIME

WAIT TO START DELAY

10-15 N/A

01 N/A

25 MIN

30 MIN

35 MIN

15 min

02 sec

05 SEC

08 SEC

10 SEC

15 SEC

20 SEC

25 SEC

30 SEC

N/A

oFF

enabLe

DISABLE*

45 sec

90 SEC

03 MIN

04 MIN

DISABLE

N/A

LOCK + UNLOCK + LOCK

LocK + LocK + LocK

03 MIN

05 MIN

10 MIN

15 MIN compustar.idatalink.com

Remote staRteR eRRoR coDes - 1 OF 1

Remote staRteR eRRoR coDes: notes

I WARNING: The following applies only when the parking lights are connected and supported by the system.

II After a remote starter failure, the parking lights will fl ash three [3x] times, then will fl ash [X] number times to indicate an error code. See table.

[X] numbeR oF PaRKing Light FLashes

Engine running.

Key in ignition at ON position.

N/A

Trunk is open.

Foot brake is ON.

Hood is open.

N/A

Tach failure.

N/A

System is in Valet Mode.

CAN communication failure

RS not synchronized. Start vehicle with OEM key for 15 sec before trying a new RS sequence.

Remote staRteR shutDown eRRoR coDes: notes

I WARNING: The following applies only when the parking lights are connected and supported by the system.

If the engine shuts down after a remote starter sequence:

Press and hold the Trunk button and the Start button at the same time for 2.5 seconds when using a 1-WAY remote.

Press once [1x] on button “4” when using a 2-WAY remote.

The parking lights will ﬂ ash four [4x] times, then will ﬂ ash

[Y] number times to indicate an error code. See table.

[Y] numbeR oF PaRKing Light FLashes

Engine tach signal is lost.

N/A

Foot brake is ON.

Hood is open.

Engine RPM limiter is ON.

Glow plug timeout error.

Vehicle is moving (VSS).

Check engine warning light is ON.

Low fuel warning light is ON.

N/A

CAN communication failure during RS sequence.

Page 14 oF 16

DOC.: #11866

• 20130723

moDuLe Diagnostics - 1 OF 1 test moDuLe

I DURING PROGRAMMING

II DURING REMOTE START

III WITH IGNITION OFF

Flashing RED

Solid RED

Flashing GREEN

Solid GREEN then OFF

OFF

Flashing RED

Solid RED

Flashing GREEN

Solid GREEN then OFF

OFF

Flashing RED

Solid RED

Flashing GREEN

Solid GREEN then OFF

OFF

Missing/wrong information from fi rmware or vehicle.

Module waiting for more vehicle information.

Additional steps required to complete module programming.

Module correctly programmed.

No activity or module already programmed.

Module incorrectly programmed.

Module correctly programmed and operational.

Reset in progress.

Invalid ground when running status from remote starter.

Module incorrectly programmed or connected.

Module not programmed. Waiting for more vehicle information.

False ground when running status from remote starter.

Reset in progress.

Module at rest and ready for a remote start sequence.

Page 15 oF 16

DOC.: #11866

• 20130723

Disconnect all connectors from module except the BLACK 20-PIN connector.

MODULE RESET PROCEDURE - 1 OF 1

Reconnect all connectors.

Disconnect the BLACK 20-PIN connector.

Repeat programming procedure.

PRESS AND HOLD programming button while connecting the BLACK 20-PIN connector.

Wait, LED 1 will ﬂash RED. RELEASE programming button.

LED 1 will turn RED for 2 seconds.

Failure to follow procedure may result with a

DTC or a CHECK ENGINE error message.

Module RESET completed.

Page 16 oF 16

DOC.: #11866

• 20130723 compustar.idatalink.com

Hello! I am an AI chatbot specifically trained to assist you with the idatastart COM-IDS(RS)-BM1-EN Install Manual. I have thoroughly reviewed the document and can help you locate the exact information you need or explain the content in clear and simple terms. Whether you’re looking for guidance on specific features, troubleshooting steps, or general usage, feel free to ask your questions. The more details you provide about your concerns or needs, the more accurately and effectively I can assist you!

Assistant typing

Assistant terminated