DTE 255
GB
Aristotig 255 AC/DC
DTE 255
Instruction manual
0457 784 201 GB 031110
Valid for serial no. 810− to 246−
1 DIRECTIVE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2 SAFETY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3 INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.1
3
3
5
Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5
4 TECHNICAL DATA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5 INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5
6
5.1
Location and connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7
6 OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7
6.1
6.2
6.3
6.4
6.5
6.6
6.7
Controls and connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Remote control unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Protection against overheating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Control panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
MMA welding (Hand welding electrodes) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TIG welding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Forced disconnection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7
8
8
8
11
12
14
7 MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
7.1
Check−up and cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
15
8 ORDERING OF SPARE PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DIAGRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ORDERING NUMBER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SPARE PARTS LIST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ACCESSORIES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
15
16
17
18
19
Rights reserved to alter specifications without notice.
TOCe
−2−
GB
1
DIRECTIVE
DECLARATION OF CONFORMITY
ESAB Welding Equipment AB, S−695 81 Laxå, Sweden, gives its unreserved guarantee that welding
power source DTE 255 from serial number 833 complies with standard IEC/EN 60974−1, in accordance with the requirements of directive (73/23/EEC) and addendum (93/68/EEC) and with standard
EN 50199 in accordance with the requirements of directive (89/336/EEC) and addendum
(93/68/EEC).
−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−−
Laxå 1998−08−11
Anders Birgersson
Managing Director
Esab Welding Equipment AB
695 81 LAXÅ
SWEDEN
2
Tel: + 46 584 81000
Fax: + 46 584 411924
SAFETY
Users of ESAB welding equipment have the ultimate responsibility for ensuring that anyone who
works on or near the equipment observes all the relevant safety precautions. Safety precautions
must meet the requirements that apply to this type of welding equipment. The following recommendations should be observed in addition to the standard regulations that apply to the workplace.
All work must be carried out by trained personnel well−acquainted with the operation of the welding
equipment. Incorrect operation of the equipment may lead to hazardous situations which can result
in injury to the operator and damage to the equipment.
1.
Anyone who uses the welding equipment must be familiar with:
S its operation
S location of emergency stops
S its function
S relevant safety precautions
S welding
2.
The operator must ensure that:
S no unauthorized person is stationed within the working area of the equipment when it is
started up.
S no−one is unprotected when the arc is struck
3.
The workplace must:
S be suitable for the purpose
S be free from drafts
4.
Personal safety equipment
S Always wear recommended personal safety equipment, such as safety glasses, flame−proof
clothing, safety gloves.
S Do not wear loose−fitting items, such as scarves, bracelets, rings, etc., which could become
trapped or cause burns.
5.
General precautions
S Make sure the return cable is connected securely.
S Work on high voltage equipment may only be carried out by a qualified electrician.
S Appropriate fire extinquishing equipment must be clearly marked and close at hand.
S Lubrication and maintenance must not be carried out on the equipment during operation.
dpb1d1ea
−3−
GB
WARNING
ARC WELDING AND CUTTING CAN BE INJURIOUS TO YOURSELF AND OTHERS. TAKE PRECAUTIONS WHEN WELDING. ASK FOR YOUR EMPLOYER’S SAFETY PRACTICES WHICH SHOULD BE
BASED ON MANUFACTURERS’ HAZARD DATA.
ELECTRIC SHOCK − Can kill
S
Install and earth the welding unit in accordance with applicable standards.
S
Do not touch live electrical parts or electrodes with bare skin, wet gloves or wet clothing.
S
Insulate yourself from earth and the workpiece.
S
Ensure your working stance is safe.
FUMES AND GASES − Can be dangerous to health
S
Keep your head out of the fumes.
S
Use ventilation, extraction at the arc, or both, to take fumes and gases away from your breathing zone
and the general area.
ARC RAYS − Can injure eyes and burn skin.
S
Protect your eyes and body. Use the correct welding screen and filter lens and wear protective
clothing.
S
Protect bystanders with suitable screens or curtains.
FIRE HAZARD
S
Sparks (spatter) can cause fire. Make sure therefore that there are no inflammable materials nearby.
NOISE − Excessive noise can damage hearing
S
Protect your ears. Use earmuffs or other hearing protection.
S
Warn bystanders of the risk.
MALFUNCTION − Call for expert assistance in the event of malfunction.
READ AND UNDERSTAND THE INSTRUCTION MANUAL BEFORE INSTALLING OR OPERATING.
PROTECT YOURSELF AND OTHERS!
ESAB can provide you with all necessary welding protection and accessories.
WARNING!
Read and understand the instruction manual
before installing or operating.
WARNING!
Do not use the power source for thawing frozen pipes.
This product is solely intended for arc welding.
dpb1d1ea
−4−
GB
3
INTRODUCTION
DTE 255 is a compact welding power source for two different welding methods.
It can be used for:
welding with tungsten electrodes (TIG), using direct or alternating current.
manual metal arc welding with coated electrodes (MMA), using direct or
alternating current.
DTE 255 is available in two designs:
S
S
S with OKC connection for the TIG torch
S with central connection for the TIG torch
Note: Remove the TIG torch when using the MMA method.
When TIG−welding, remove the electrode holder.
ESAB’s accessories for the product can be found on page 19.
3.1
Equipment
DTE 255 is delivered with:
S
Mains cable (3 m)
S
Return cable (5 m)
S
Gas hose
S
Hose clamps
4
TECHNICAL DATA
DTE 255
Permissible load at
25% duty cycle (MMA)
60% duty cycle (MMA)
100% duty cycle (MMA)
250 A / 30 V
200 A / 28 V
165 A / 26 V
50% duty cycle (TIG)
60% duty cycle (TIG)
100% duty cycle (TIG)
250 A / 20 V
225 A / 19 V
170 A / 17 V
5−250 A, DC
Setting range, TIG
5*−250 A, AC
Setting range, MMA
5−250 A
Slope up
0 − 10 s
Slope down
0 − 10 s
Gas preflow, adjustable on the circuit board
0− 5s
Gas postflow
3 − 30 s
Open circuit voltage
70 − 90 V DC
No−load power, MMA
95 W
No−load power, TIG
50 W
Useful power, P (at max. current MMA)
10 kW
Apparent power, S (at max. current MMA)
10.6 kW
dpb1d1ea
−5−
GB
DTE 255
Power factor at max. current, MMA
0.93
Efficiency at max. current, MMA
0.75
Mains voltage
400 V
Mains frequency
50 − 60 Hz
Welding cable, sectional area
35 mm2
Fuse, slow−acting
16 A
Mains cable, sectional area
4 x 2.5 mm2
Dimensions l x w x h
510 x 310 x 555 mm
Weight
45 kg
+/− 10%
3 phases
Application class
IP 23
Enclosure class
*) The minimum current during AC welding depends on the alloy used for the aluminium plates and
their surface cleanliness.
Duty cycle
The duty cycle refers to the time as a percentage of a ten−minute period that you can weld at a certain load without overloading.
Application class
The symbol
indicates that the power source is designed for use in areas with increased
electrical hazard.
Enclosure class
The IP code indicates the enclosure class, i. e. the degree of protection against penetration by solid
objects or water. Equipment marked IP23 is designed for indoor and outdoor use.
5
INSTALLATION
The installation must be executed by a professional.
WARNING!
This product is intended for industrial use. In a domestic environment this product may cause radio
interference. It is the user’s responsibility to take adequate precautions.
DTE 255 has mains voltage compensation, which means that +/− 10% variation in
the supply voltage produces only +/− 0.2% variation in the welding current.
To reduce the voltage drop resulting from the use of long welding cables, a cable
with a larger sectional area than the one indicated under Technical Data on page 5
can be used.
When the power source is started, the cooling fans work at a reduced rotation
speed, partly to reduce the amount of dirt that can be sucked in and partly to ensure
a lower noise level.
When the power source requires increased cooling, the fans work at a higher
rotation speed.
dpb1d1ea
−6−
GB
5.1
Location and connection
Place the welding power source so that the cooling air in− and outlets remain
free.
S Connect the shielding gas (see fig. on page 7).
S Connect the TIG torch and the torch return cable, alternatively the welding and
return cable of the electrode holder (see fig. on page 7).
S Make sure the welding power source is connected to the right mains voltage and
that it is properly fused. Connect to earth according to applicable regulations.
Rating plate with connection data is located on the rear of the welding power
source.
The machine is now ready for use.
S
6
OPERATION
General safety regulations for the handling of the equipment can be found on
page 3. Read through before you start using the equipment!
6.1
Controls and connections
Central connection
A
Mains switch ON/OFF
H
Mains voltage ON, LED
B
Connection for remote control unit
J
Welding voltage ON, LED
C
Torch connector
L
Error / Overheating, LED
D
Connection for electrode holder (MMA)
M
Flow guard, LED
(Functions when the cooling unit is
connected)
E
OKC connection for TIG torch
N
Connection for shielding gas to the machine
F
Return cable connection
O
Control unit, digital display
G
Shielding gas connection
P
Central connection for TIG torch
N.B. The positions C and G are dropped when the central connection is used.
dpb1d1ea
−7−
GB
When the mains switching device is turned on, the diode (H) goes on.
When open circuit voltage is applied diode (J) goes on.
When an error occurs, for example overheating, diode (L) goes on.
When there is no water flow diode (M) goes on.
When there is a fault that can cause temporary high output voltage, the LED
switches off (J), (output voltage has been switched off). When idling for longer than
30 minutes, the output voltage is switched off and diode (J) goes out.
Restart by turning the switch (1) to TIG mode and then back to MMA mode.
6.2
Remote control unit
For both the TIG and MMA methods the welding current can be adjusted by way of a
remote control unit. The welding power source registers automatically when a
remote control unit is connected.
If the remote control is to include the whole current range, the current must be set to
max. on the welding power source.
Max. value = The reference value set on the welding power source.
6.3
Protection against overheating
Three thermal cut−outs prevent the power source being overloaded as a result of too
high temperature. If this should happen, the welding current is interrupted and the
yellow diode (L) goes on. (See page 7.)
When the temperature has gone down, the welding current circuit is reclosed and
the diode goes out.
6.4
Control panel
1
Method selection switch
S
S
S
S
MMA welding (hand welding electrodes)
TIG, two−stroke (also for remote control)
TIG, four−stroke
TIG four−stroke with the possibility to shift
between two currents (shift function). See items 8
and 9 on page 9 for setting of the two currents.
2
Ignition selection switch
S
S
HF ignition
Lift−Arc ignition, see page 10.
dpb1d1ea
−8−
GB
3
Pulsing selection switch
S
S
S
Non−pulsed welding, d.c. and a.c.
Welding with square−wave pulsing; d.c. and a.c.
Welding with trapezi−form pulsing; d.c. and a.c.
4
Polarity selection switch
S
S
S
Alternating current
Square−wave alternating current
Direct current, negative electrode (normal in TIG
welding)
Direct current, positive electrode
Direct current, negative electrode, but with positive
electrode at the start (for example for 3.2 mm
electrodes, TIG welding).
S
S
5
Potentiometer for Hot Start
S
For setting and optimising the starting cycle with
regard to the electrode size.
TIG welding ( 10...500 ms )
MMA welding (100ms...2s)
6
Potentiometer for Arc−Force
S
For setting and optimising the Arc−Force function
(Anti− Stick), for MMA welding only.
7
Potentiometer
S
For setting the slope−up time of the welding
current (0 to 10 seconds).
8
Potentiometer I1
S
For setting the non−pulsed welding current and the
current pulse when welding with pulsed current.
9
Potentiometer I2
S
For setting the background current for pulsed
welding and the lower current level when using the
shift function.
10
Potentiometer
S
For setting the welding current slope−down (0 to
10 seconds).
11
Potentiometer
S
For setting the gas postflow time (3 to 30
seconds).
12
Potentiometer for setting the frequency
This potentiometer has double functions:
Potentiometer for setting the balance
This potentiometer has double functions:
13
For setting the pulse frequency between 0.3 and
300 Hz for pulsed welding with direct current.
S For setting the a.c. frequency between 30 and 300
Hz for non−pulsed welding with alternating current.
N.B. When welding with pulsed alternating current,
the a.c. frequency is automatically set to 100 Hz!
The max. pulse frequency to be set is then 100 Hz!
S
S
For setting the balance between positive and
negative half−wave when welding with alternating
current to optimise the cleaning or the penetration.
(Turning right =>increased penetration.)
S For setting the time relation between the
background and the peak current when welding
with direct current.
(Turning right =>longer pulse current time.)
N.B. When welding with pulsed a.c. the time
balance between the pulse current and the base
current will automatically be 50/50%.
The relationship between positive and negative
halfwave is adjusted in the same way as nonpulsating
AC welding.
dpb1d1ea
−9−
GB
Position
= MMA
In this position the welding power source is prepared for welding with coated
electrodes. The HF unit and the Lift−Arc are disconnected, and the hot−start function
is activated in order to supply incresaed current at the start.
Position
= HF unit ON
When pressing the torch trigger the gas starts flowing, the HF unit goes on,
generating an electric spark between the electrode and the welding material, the gas
is ionised and an arc is produced. When the arc is stable, the HF unit will
automatically be disconnected.
Position
= Lift−Arc
By Lift−Arc is meant that you place the torch with the electrode on the spot where
you want to start the welding, press the torch trigger and lift up the torch. In doing so
an arc is produced.
The current slowly increases up to the set value during the set “slope up” time. When
you want to finish welding, the contact is released and the current slowly decreases
to the set “slope down” time.
Place the electrode against the workpiece.
Press in the torch trigger.
Tilt the torch a little, lift and an arc is produced.
To stop, release the torch trigger.
Position
Two/four−stroke
Two−stroke means that the arc is struck when the torch trigger is pressed and
extinguished when it is released.
Four−stroke means that it is not necessary to keep the torch trigger pressed while
the welding is going on. The arc is struck by pressing an releasing the switch and is
extinguished by repeating the action.
Four−stroke with the possibility to switch between two currents (switching function).
Through short activation of the burner cpontact, the switching function gives rise to
switching between two adjustable currents.
If the burner contact is kept pressed in the current starts to slope down.
dpb1d1ea
− 10 −
GB
6.5
MMA welding (Hand welding electrodes)
6.5.1
Adjusting the control panel for MMA welding
S
Connect the welding and return cable to the OKC terminals D and F.
S
Set switch (1) to the position for hand welding electrodes.
The LED (J) indicates that open circuit voltage is available on the welding
terminals.
(See also point 5.2.)
S
Set the desired value for welding current using potentiometer (8).
It is also possible to use pulsed welding current. The settings are made in the
same way as for pulsed TIG welding.
S
Potentiometer (5) is used for stepless setting of the Hot−Start function,
potentiometer (6) for stepless setting of the Arc−Force function, and thereby the
control dynamics.
Depending on the electrode type to be used, direct current and polarity or one of
the alternating current alternatives can be selected by way of switch (4) without
shifting the welding cables.
The welding current can be set over a hand−operated remote control unit.
S
dpb1d1ea
− 11 −
GB
6.6
TIG welding
In TIG welding the torch trigger has three different functions:
S
Two−stroke
S
Four−stroke
S
Four−stroke with the possibility to shift between two currents (shift function).
6.6.1
Adjusting the control panel for TIG welding
S
Connect the TIG burner and the earth lead into the OKC outputs E and F, (for
central connection: terminals P and F).
S
Set switch (1) to the desired position.
If a foot−operated remote control unit is to be used, set switch (1) to position
two−stroke.
NB. For direct current control over the foot−operated remote control unit, the
potentiometer (7) and (10) must be set to position 0.
A hand−operated remote control unit can be used for both two−stroke and
four−stroke to set the welding current.
S
Select the desired striking method using switch (2).
S
Adjust the welding current using potentiometer (8).
S
Select the desired type of pulsing using switch (3).
S
For the shift function/pulsing, adjust the lower current value using potentiometer
(9).
dpb1d1ea
− 12 −
GB
6.6.2
Schematic pulsed welding sequence:
6
1. The gas preflow time is preset at 10 ms.
2. Hot start:
S
The start current is preset at 100 A.
S
The time is adjusted on the front panel: 20 − 500 ms.
(For MMA welding: 200 − 2000 ms.)
3. The start current is 15 A.
4. The slope−up time is adjusted on the front panel: 0 − 10 s.
5. The pulse current is adjusted on the front panel: 5 − 250 A.
6. The background current is adjusted on the front panel: 10 − 90% of the pulse
current.
7. The slope−down time is adjusted on the front panel: 0 − 10 s.
8. At termination, the current is pre−set to 5 A.
9. The gas postflow time is adjusted on the front panel: 3 − 30 s.
dpb1d1ea
− 13 −
GB
6.6.3
Setting direct and alternating current
Direct current:
S
Set switch (4) to the position for direct current with negative polarity.
If pulsing has been selected:
S
Set the pulse current value using potentiometer (8).
S
Set the background current in per cent of the pulse current value using
potentiometer (9).
S
Set the pulse frequency using potentiometer (12).
S
Set the time relation between pulse and background current using
potentiometer (13).
Alternating current:
Two different types of alternating current can be set over switch (4):
S
A sine−wave type, characterised by low noise and a soft arc. Effective when low
frequencies are used!
S
A square−wave type, characterised by a hard and stable arc, resulting in a
somewhat higher noise level.
The arc is always struck by way of direct current which is then automatically
switched over to alternating current.
Increased alternating current frequency gives a concentrated and stable arc, suitable
above all when a low amperage is used and when welding in extremely thin plate.
The displacement (balance) of the half−wave in positive direction leads to increased
cleaning, and in negative direction to increased penetration.
(Turn potentiometer (13) more to the right for increased penetration!)
6.7
Forced disconnection
If the torch trigger or the foot−operated remote control unit has been activated and
no arc has been generated, the open circuit voltage is automatically disconnected
after 2 seconds. The same applies in the event of an arc interruption.
This function protects from:
S
Uncontrolled arc strike
S
Material damage
S
Shielding gas drop−out
S
Accidents
dpb1d1ea
− 14 −
GB
7
MAINTENANCE
Regular maintenance is important for safe, reliable operation.
Only those persons who have appropriate electrical knowledge (authorized
personnel) may remove the safety plates to connect or carry out service,
maintenance or repair work on welding equipment.
Note!
All guarantee undertakings from the supplier cease to apply if the customer himself
attempts any work in the product during the guarantee period in order to rectify any
faults.
7.1
Check−up and cleaning
Clean the welding power source once a year using
dry compressed air (reduced pressure). The dust
filter is to be checked up and cleaned regularly.
If the welding power source is used in a dusty and
dirty environment, the cleaning should be
performed more frequently.
For maximal service reliability it could be
advisable to let an authorised retailer service the
machine once a year.
8
ORDERING OF SPARE PARTS
bt07d109
DTE 255 is designed and tested in accordance with the international and European
standards IEC/EN 60974−1 and EN 50199. It is the obligation of the service unit which
has carried out the service or repair work to make sure that the product still conforms
to the said standard.
Spare parts may be ordered through your nearest ESAB dealer, see the last page of
this publication.
dpb1d1ea
− 15 −
Diagram
dpb1e11a
− 16 −
Edition 031110
DTE 255
Ordering number
Ordering no.
Denomination
Type
Notes
0301 035 880 Welding power source
DTE 255
with central connection for the TIG torch
0301 035 881 Welding power source
DTE 255
with OKC connection for the TIG torch
0457 784 990 Spare part list
DTE 255
dpb1o11a
− 17 −
Edition 031110
DTE 255
Spare parts list
Item
Qty
Ordering no.
1
1
0301 028 001
Grill
2
1
0301 054 001
Filter
3
3
0441 819 001
Screw
4
1
0301 027 001
Grill
5
1
0301 053 001
Filter
dpb1s
Denomination
− 18 −
Edition 031110
DTE 255
Accessories
Trolley (with room for gas bottle) . . . . . . . . . . . . 0301 100 880
Return cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0369 857 888
Foot control FS 002 . . . . . . . . . . . . . . . . . . . . . . 0349 090 886
Cooling unit OCF 2D . . . . . . . . . . . . . . . . . . . . . 0457 216 881
TIG torches
HW 26 R, 4 m with OKC connection . . . . . . . . .
HW 26 R, 4 m with central connection . . . . . . .
HW 20, 4 m with OKC connection . . . . . . . . . . .
HW 20, 4 m with central connection . . . . . . . . .
dpb1a11a
− 19 −
0588 000 738
0588 000 740
0588 000 744
0588 000 746
Edition 031110
ESAB subsidiaries and representative offices
Europe
AUSTRIA
ESAB Ges.m.b.H
Vienna−Liesing
Tel: +43 1 888 25 11
Fax: +43 1 888 25 11 85
BELGIUM
S.A. ESAB N.V.
Brussels
Tel: +32 2 745 11 00
Fax: +32 2 726 80 05
THE CZECH REPUBLIC
ESAB VAMBERK s.r.o.
Prague
Tel: +420 2 819 40 885
Fax: +420 2 819 40 120
DENMARK
Aktieselskabet ESAB
Copenhagen−Valby
Tel: +45 36 30 01 11
Fax: +45 36 30 40 03
FINLAND
ESAB Oy
Helsinki
Tel: +358 9 547 761
Fax: +358 9 547 77 71
FRANCE
ESAB France S.A.
Cergy Pontoise
Tel: +33 1 30 75 55 00
Fax: +33 1 30 75 55 24
GERMANY
ESAB GmbH
Solingen
Tel: +49 212 298 0
Fax: +49 212 298 204
GREAT BRITAIN
ESAB Group (UK) Ltd
Waltham Cross
Tel: +44 1992 76 85 15
Fax: +44 1992 71 58 03
ESAB Automation Ltd
Andover
Tel: +44 1264 33 22 33
Fax: +44 1264 33 20 74
HUNGARY
ESAB Kft
Budapest
Tel: +36 1 20 44 182
Fax: +36 1 20 44 186
ITALY
ESAB Saldatura S.p.A.
Mesero (Mi)
Tel: +39 02 97 96 81
Fax: +39 02 97 28 91 81
THE NETHERLANDS
ESAB Nederland B.V.
Utrecht
Tel: +31 30 248 59 22
Fax: +31 30 248 52 60
NORWAY
AS ESAB
Larvik
Tel: +47 33 12 10 00
Fax: +47 33 11 52 03
POLAND
ESAB Sp.z.o.o
Warszaw
Tel: +48 22 813 99 63
Fax: +48 22 813 98 81
PORTUGAL
ESAB Lda
Lisbon
Tel: +351 1 837 1527
Fax: +351 1 859 1277
SLOVAKIA
ESAB Slovakia s.r.o.
Bratislava
Tel: +421 7 44 88 24 26
Fax: +421 7 44 88 87 41
SPAIN
ESAB Ibérica S.A.
Alcobendas (Madrid)
Tel: +34 91 623 11 00
Fax: +34 91 661 51 83
SWEDEN
ESAB Sverige AB
Gothenburg
Tel: +46 31 50 95 00
Fax: +46 31 50 92 22
ESAB International AB
Gothenburg
Tel: +46 31 50 90 00
Fax: +46 31 50 93 60
SWITZERLAND
ESAB AG
Dietikon
Tel: +41 1 741 25 25
Fax: +41 1 740 30 55
North and South America
Asia/Pacific
CHINA
Shanghai ESAB A/P
Shanghai
Tel: +86 21 6539 7124
Fax: +86 21 6543 6622
INDIA
ESAB India Ltd
Calcutta
Tel: +91 33 478 45 17
Fax: +91 33 468 18 80
INDONESIA
P.T. Esabindo Pratama
Jakarta
Tel: +62 21 460 01 88
Fax: +62 21 461 29 29
MALAYSIA
ESAB (Malaysia) Snd Bhd
Selangor
Tel: +60 3 703 36 15
Fax: +60 3 703 35 52
SINGAPORE
ESAB Singapore Pte Ltd
Singapore
Tel: +65 861 43 22
Fax: +65 861 31 95
ESAB Asia/Pacific Pte Ltd
Singapore
Tel: +65 861 74 42
Fax: +65 863 08 39
Representative offices
BULGARIA
ESAB Representative Office
Sofia
Tel/Fax: +359 2 974 42 88
EGYPT
ESAB Egypt
Dokki−Cairo
Tel: +20 2 390 96 69
Fax: +20 2 393 32 13
ROMANIA
ESAB Representative Office
Bucharest
Tel/Fax: +40 1 322 36 74
RUSSIA−CIS
ESAB Representative Office
Moscow
Tel: +7 095 937 98 20
Fax: +7 095 937 95 80
ESAB Representative Office
St Petersburg
Tel: +7 812 325 43 62
Fax: +7 812 325 66 85
Distributors
For addresses and phone
numbers to our distributors in
other countries, please visit our
home page
www.esab.com
SOUTH KOREA
ESAB SeAH Corporation
Kyung−Nam
Tel: +82 551 289 81 11
Fax: +82 551 289 88 63
UNITED ARAB EMIRATES
ESAB Middle East
Dubai
Tel: +971 4 338 88 29
Fax: +971 4 338 87 29
ARGENTINA
CONARCO
Buenos Aires
Tel: +54 11 4 753 4039
Fax: +54 11 4 753 6313
BRAZIL
ESAB S.A.
Contagem−MG
Tel: +55 31 3369 4333
Fax: +55 31 3369 4440
CANADA
ESAB Group Canada Inc.
Missisauga, Ontario
Tel: +1 905 670 02 20
Fax: +1 905 670 48 79
MEXICO
ESAB Mexico S.A.
Monterrey
Tel: +52 8 350 5959
Fax: +52 8 350 7554
USA
ESAB Welding & Cutting Products
Florence, SC
Tel: +1 843 669 44 11
Fax: +1 843 664 44 58
ESAB AB
SE−695 81 LAXÅ
SWEDEN
Phone +46 584 81 000
www.esab.com
031021
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising