Pricing

Pricing
Option No.
0100‐0050
1005‐0133
1025‐0002
1025‐0003
1025‐0004
1025‐0005
1025‐0006
1025‐0007
1025‐0008
1025‐0009
1025‐0010
1025‐0011
1025‐0012
1025‐0013
1025‐0014
1025‐0015
1025‐0016
1025‐0017
1025‐0018
1025‐0020
1025‐0021
1025‐0022
1025‐0023
1025‐0024
1025‐0027
1025‐0028
1025‐0029
1025‐0030
1025‐0031
1025‐0034
1025‐0035
1025‐0036
Description
Rear tandem wheel well modification to driver and officer side to increase storage, by lowering extrusion above. Note SCBA bottle storage not available. Applies only to HP100 rear mount platform without pump.
(4) door, 237" WB & 47" frame cut, front tow hooks, 12K & 23K axles, ABS brakes, 1000 sq.in. radiator, 50 gal. left hand fuel tank, MBE900‐300 6.4L 300 HP 98 EPA Engine EVS3000 transmission, MBE off/low/high compression and exhaust brake (2) 1850 CCA batteries, 270 alternator, ember separator and AC. Dual air horns, 911 Universal High Back Drivers Air Seat, 911 Universal SCBA Non Suspended Officers, (3) 911 Universal SCBA Rear Seats With Under Seat Storage Dual W\estT Coast Bright Finish Heated Remote with Left and Right Mirrors. 294‐046 Separate taillight programming. Export chassis to Chilei ZCHILE‐120308
Dana 22I 22,800 lb. front axle.
Meritor FL941 front axle 16,000lb
Meritor FL941 front axle 18,000 lb. with assist cylinder.
Meritor FL‐941 front axle 18,700 lb.
Meritor FL941 front axle 20,000 lbs.
Meritor FL941 front axle 21,000lb
Meritor FL941 front axle 21,500lb
Meritor FL943 front axle 18,000 lbs.
Meritor FL‐943 front axle 18,700 lb.
Meritor FL‐943 front axle 20,000 lb.
Meritor FL‐943 front axle 21,000 lb.
Meritor FL‐943 front axle 21,500 lbs.
Meritor front drive axle and suspension 16,540#
Meritor front drive axle and suspension 18,000#
Meritor RS‐24‐160 single rear axle 24,000 lb. capacity.
Meritor RS‐25‐160 single rear axle 27,000 lb. capacity.
Meritor RS‐30‐185 single rear axle 31,000 lb. capacity.
Meritor RT‐46‐160 rear tandem axle 46,000 lb. capacity.
Meritor RT‐46‐160 rear tandem axle 48,000 lb. capacity.
Meritor RT‐50‐160 rear tandem axle 52,000 lb. capacity.
Meritor RT‐50‐160 rear tandem axle 54,000 lb. capacity.
Meritor RT‐58‐185 rear tandem axle 60,000 lb. capacity.
Driver controlled rear differential.
Koni shock absorbers for front axle ‐ adjustable.
Front shock absorbers.
Stemco oil seal front axle. Chicago Rawhide seal with Stemco sight glass will be supplied when front disc brakes are selected.
Spiral pins front suspension.
Automatic traction control. In addition to standard ABS system.
Koni shock absorbers for rear axle.
Automatic Traction Control System 6x4/6x6
PRICE
$518.00
$81,208.00
$20,583.00
$12,441.00
$14,198.00
$18,657.00
$19,332.00
$19,332.00
$19,601.00
$15,143.00
$19,601.00
$20,414.00
$20,682.00
$21,089.00
$13,789.00
$41,152.00
$12,441.00
$13,925.00
$15,548.00
$33,117.00
$33,117.00
$41,902.00
$41,902.00
$52,716.00
$888.00
$386.00
$208.00
$126.00
$1,927.00
$666.00
$612.00
$2,270.00
Option No.
1025‐0038
1025‐0039
1025‐0058
1025‐0059
1025‐0060
1025‐0061
1025‐0063
1025‐0064
1025‐0065
1025‐0066
1025‐0067
1025‐0069
1025‐0071
1025‐0073
1025‐0074
1025‐0075
1025‐0076
1025‐0077
1025‐0078
1025‐0079
1025‐0081
1025‐0084
1025‐0085
1025‐0086
1025‐0087
1025‐0088
1025‐0089
1025‐0090
1025‐0095
1025‐0096
1025‐0097
1025‐0099
Description
Meritor RT‐58‐185 rear tandem axle 62,000 lb. capacity.
Rear steer axle FL941 21,500lb for tiller.
Stemco oil seal rear axle (per axle). Not available with disc brakes.
Meritor front drive axle and suspension 21,000#
Meritor FL‐943 front axle 22,100 lb.
A single indicator light installed in cab to show the activation of any of the brake wear indicator switches installed on the caliper at each wheel location.
Control in cab for kneeling of rear air ride suspension. Estimated dump time will be 30 seconds. Switch on dash to "Kneel" rear wire through park brake valve to allow Kneel only when park brake is activated.
Independent front axle/suspension ‐ 18,000 lb. Not available with Series 60 engine.
Independent front axle/suspension ‐ 20,000 lb. Not available with Series 60 engine.
Independent front axle/suspension ‐ 22,800 lb. Not available with Series 60 engine.
Independent front axle/suspension ‐ 24,000 lb. Not available with Series 60 engine.
Driver Controlled Dif Lock. on chassis with 26,000 rear axle.
OBS ‐ Meritor RS‐30‐185 single rear axle 33,000lb capacity.
Meritor RS‐30‐185 single rear axle 31,500 lb. capacity.
Independent front axle/suspension rated at 18,700 lb due to tires (Uses 20,000 lb springs). Not available with Series 60 engine.
Independent front axle/suspension rated at 21,000 lb due to tires (Uses 22,800 lb springs). Not available with Series 60 engine.
Independent front axle/suspension rated at 21,500 lb due to tires (Uses 22,800 lb springs). Not available with Series 60 engine.
Rear steer axle FL941 22,100lb for tiller.
S‐Cam brakes to have Haldex brand slack adjusters (per axle).
Meritor RS‐23‐240 two speed single rear axle 24,000lb capacity.
Chicago Rawhide oil seal rear axle (per axle). Not available with disc brakes.
Driver Controlled Dif Lock (Rearward rear axle). For use with International chassis with 40K tandem rear axle.
Driver Controlled Dif Lock (Rearward rear axle). For use with International chassis with 46K tandem rear axle.
Meritor FL941 front axle 18,500lb.
Dana S35‐590 single rear axle 32,500lb capacity. Requires Bendix rear brakes.
Synthetic 75w90 gear oil for rear axle.
Meritor RS‐26‐185 single rear axle 27,000lb capacity
Meritor RT‐46‐160 rear tandem axle rated at 40,000lb capacity.
Meritor RS‐30‐185 single rear axle 29,000lb capacity
Front axle capacity upgrade for 23,000lb rating.
Meritor RS‐30‐185 single rear axle 33,000 lb. capacity. Requires 16.5" x 8.625" cast shoe brakes and 33K suspension.
Chassis axle package with FL‐941 front axle with 18,000lb. suspension and RS‐24‐160 rear axle with 24,000lb. suspension. Includes front disc and rear cam brakes, Anti‐Lock Brake System (ABS) and air Inlet located inside the driver side door area. Custom ES.
PRICE
$62,176.00
$27,744.00
$267.00
$41,406.00
$21,880.00
$387.00
$579.00
$47,567.00
$47,567.00
$47,567.00
$47,567.00
$604.00
$15,548.00
$15,548.00
$47,567.00
$47,567.00
$47,567.00
$27,744.00
$353.00
$17,507.00
$267.00
$803.00
$627.00
$18,657.00
$19,780.00
$423.00
$15,548.00
$33,117.00
$15,548.00
$27,340.00
$15,548.00
$0.00
Option No.
1025‐0100
1025‐0101
1025‐0102
1025‐0103
1025‐0106
1025‐0107
1025‐0108
1025‐0110
1025‐0114
1025‐0115
1025‐0116
1025‐0119
1025‐0120
1025‐0121
1025‐0122
1025‐0123
1025‐0124
1025‐0125
1025‐0127
1025‐0132
1025‐0133
1025‐0134
1025‐0135
1025‐0137
1025‐0138
1025‐0139
1025‐0140
Description
Chassis axle package with FL‐941 front axle with 18,000lb. suspension and RS‐24‐160 rear axle with 24,000lb. suspension. Includes front disc and rear cam brakes, Electronic Stability Control (ESC) for 172" WB and air inlet located inside the driver side door area. Custom ES.
Chassis axle package with FL‐941 front axle with 18,000lb. suspension and RS‐24‐160 rear axle with 24,000lb. suspension. Includes front disc and rear cam brakes, Electronic Stability Control (ESC), and air inlet located inside the driver side door area. 180" and 194" WB Custom ES.
Chassis axle package with FL‐941 front axle with 18,000lb. suspension and RS‐24‐160 rear axle with 24,000lb. suspension. Includes front disc and rear cam brakes, Electronic Stability Control (ESC), and air inlet located inside the driver side door area. 202", 206", and 214" WB Custom ES.
Chassis axle package with FL‐941 front axle with 18,000lb. suspension and RS‐24‐160 rear axle with 24,000lb. suspension. Includes front disc and rear cam brakes, Anti‐Lock Brake System (ABS) and air Inlet located inside the driver side door area. Export only Custom ES with 98 EPA engine.
Driver Control Differential for M2.
Synthetic 75w90 gear oil for front axle.
Meritor RS‐30‐185 single rear axle 30,000lb capacity
Meritor RT‐50‐160 rear tandem axle 50,000lb capacity
Meritor FL943 front axle 18,700lb with multi‐leaf front springs.
The front axle to be an 18K Dana Spicer with taperleaf and shocks.
The rear axle to be tandem with 40K Dana Spicer with air ride suspension.
3 year extended parts and labor warranty (total of 4 year warranty) on Timoney Independant Front Axle. Does not include steering components.
Driver controlled rear differential. Includes guarded toggle switch located on driver side diagnostic panel.
2 year extended parts and labor warranty (total of 3 year warranty) on Timoney Independent Suspension Front Axle. Does not include steering components.
Stemco Hubometer on driver side of rear axle.
Meritor FL941 front axle 19,840 lb.
Meritor FL943 front axle 20,000 lb. Springs to have Berlin style eyes with rubber bushings.
Meritor FL943 front axle 19,840 lb.
Meritor FL941 front axle 18,000 lb with multi‐leaf front springs.
Koni shock absorbers for front axle ‐ non‐adjustable. For use with IFS front axle only.
Meritor FL943 front axle 20,000 lb with multi‐leaf front springs.
Meritor MT‐40‐14X rear tandem axle 40,000 lb. capacity.
AxleTech FS25 front axle 18,700 lb. Includes sight guage.
Meritor FL943 front axle 19,220 lb.
AxleTech FS25 front axle 20,000 lb. Includes sight guage.
AxleTech front drive axle and suspension 18,700#.
Spicer 232S4 single rear axle 24,000 lb. capacity with power divider (232D4 with DCDL). Includes drivelines to front axle.
PRICE
$3,378.00
$3,378.00
$3,378.00
$0.00
$519.00
$131.00
$15,548.00
$41,902.00
$20,063.00
$0.00
$0.00
$2,798.00
$888.00
$1,867.00
$153.00
$18,657.00
$20,759.00
$19,601.00
$12,891.00
$386.00
$20,864.00
$28,385.00
$20,754.00
$19,601.00
$20,754.00
$46,138.00
$18,629.00
Option No.
1025‐0141
1025‐0142
1025‐0144
1025‐0145
1025‐0146
1025‐0147
1025‐0148
1025‐0149
1025‐0150
1025‐0151
1025‐0152
1025‐0153
1025‐0158
1025‐0159
1025‐0163
1025‐0164
1025‐0165
1025‐0169
1025‐0170
1025‐0171
1025‐0172
1025‐0174
1025‐0175
1025‐0178
1025‐0180
1025‐0181
1025‐0182
1025‐0184
1025‐0186
1050‐0000
1050‐0001
1050‐0002
1050‐0003
Description
Spicer 301S4 single rear axle 31,000 lb. capacity with power divider. Includes drivelines to front axle.
Chicago oil seal front axle. Chicago Rawhide seal with Chicago Rawhide sight glass (model 1743) will be supplied when front disc brakes are selected.
The front axle shall be fitted with a 1" spacer block per customer request. The spacer block shall not compromise step height requirements or impose unacceptable rake characteristics when added. Chassis engineering approval required.
Front suspension grease points/spring pins shall have fittings inboard of the frame rails with grease fittings pointed towards the center of the chassis to prepare for dealer/customer supplied lubrication system.
Reyco Granning independent front suspension ‐ 18,000 lb. Includes shocks and sight glass on hubs.
Reyco Granning independent front suspension ‐ 18,700 lb. Includes shocks and sight glass on hubs.
Reyco Granning independent front suspension ‐ 19,840 lb. Includes shocks and sight glass on hubs.
Reyco Granning independent front suspension ‐ 20,000 lb. Includes shocks and sight glass on hubs.
Reyco Granning independent front suspension ‐ 21,000 lb. Includes shocks and sight glass on hubs.
Reyco Granning independent front suspension ‐ 21,500 lb. Includes shocks and sight glass on hubs.
Reyco Granning independent front suspension ‐ 22,800 lb. Includes shocks and sight glass on hubs.
Reyco Granning independent front suspension ‐ 24,000 lb. Includes shocks and sight glass on hubs.
Stemco sight glass guards.
Meritor front drive axle and suspension 19,840#
Rear axle high water ventilation tube.
Meritor MFS18 front axle rated at 16,000 lb.
Meritor FL‐943 front axle 22,500 lb.
Dana Spicer single rear axle with 27,000 lb capacity with power divider. Includes drivelines to front axle.
Meritor MFS18 front axle rated at 18,000 lb.
Dana 22I 24,000 lb. front axle.
Meritor front drive axle and suspension 22,800#
Meritor FL941 front axle 18,000 lb.
Meritor RS‐25‐160 single rear axle at 24,000 lb. rated capacity.
Meritor FL941 front axle 21,200lb
Stemco oil seal tiller axle.
Dana S35‐590 single rear axle 33,000lb capacity. Requires Bendix rear brakes.
Dana S35‐590 single rear axle 35,000lb capacity. Requires Bendix rear brakes. Unit will have an intermittent speed rating due to rear tires.
Marmon‐Herrington MT‐22 front drive axle and suspension 19,840 lb.
Meritor RS‐30‐185 single rear axle 28,450lb capacity
Steel wheels for front axle (2).
Alcoa aluminum wheels for front axle (2).
Steel wheels for rear axle (4).
Alcoa aluminum wheels for rear axle (4).
PRICE
$23,511.00
$126.00
$229.00
$575.00
$33,261.00
$33,261.00
$33,261.00
$33,261.00
$33,261.00
$33,261.00
$33,261.00
$33,261.00
$108.00
$41,406.00
$246.00
$12,261.00
$21,834.00
$23,511.00
$12,261.00
$20,961.00
$47,508.00
$12,441.00
$13,925.00
$19,332.00
$126.00
$19,780.00
$19,780.00
$42,382.00
$15,548.00
$365.00
$1,967.00
$723.00
$3,927.00
Option No.
1050‐0004
1050‐0005
1050‐0007
1050‐0008
1050‐0009
1050‐0010
1050‐0011
1050‐0012
1050‐0017
1050‐0018
1050‐0019
1050‐0024
1050‐0025
1050‐0026
1050‐0027
1050‐0028
1050‐0029
1050‐0030
1050‐0031
1050‐0032
1050‐0033
1050‐0034
1050‐0035
1050‐0036
1050‐0037
1050‐0038
1050‐0039
1050‐0041
Description
Steel wheels for rear axles (8).
Alcoa aluminum wheels for rear axles (8).
Front axle wheel trim kit. Includes stainless steel lug nut covers (chrome plated plastic if applicable) and center cap with E‐ONE logo. Note: Center cap will have an inspection port IPO a logo if equipped with Stemco oil seals.
Rear axle (single) wheel trim kit. Includes stainless steel lug nut covers (chrome plated plastic if applicable) and center cap with E‐ONE logo. E‐ONE custom chassis w/steel wheels will have chrome plated plastic lug covers.
Rear axle (tandem) wheel trim kit. Includes stainless steel lug nut covers (chrome plated plastic if applicable) and center caps with E‐ONE logo. E‐ONE custom chassis w/steel wheels will have chrome plated plastic lug covers.
Wheel Covers stainless steel (Real Wheels) 4x4
Wheel Covers stainless steel (Real Wheels) 6x6
Wheel Covers stainless steel 8x8 (Real Wheels)
Each inside wheel of the single rear axle shall have valve stem extensions.
Each inside wheel of the tandem rear axles shall have valve stem extensions.
Two steel wheels painted job color on both the inside and outside facing for front axle.
(1) spare steel wheel painted job color for front axle.
(1) spare steel wheel painted job color for rear axle.
Front axle Wheel Trim kit. Includes stainless steel lug nut covers and center cap (no logo). Note: Center cap will have an inspection port if equipped with Stemco oil seals.
Rear axle (single) wheel trim kit. Includes stainless steel lug nut covers (chrome plated plastic if applicable) and center caps (no logo). E‐
ONE custom chassis w/ steel wheels will have chrome plated plastic lug covers.
Rear axle (tandem) Wheel Trim kit. Includes stainless steel lug nut covers (chrome plated plastic if applicable) and center cap (No logo). E‐ONE custom chassis w/ steel wheels will have chrome plated plastic lug covers.
Front & rear axle wheel simulator kit. Includes stainless steel wheel simulator and center cap with E‐ONE logo.
Rear axle (single) wheel trim kit. Includes stainless steel lug nut covers and center caps (no logo). E‐ONE custom chassis w/ steel wheels will have chrome plated plastic lug covers.
Front axle wheel simulator kit. Includes stainless steel wheel simulator and center cap with E‐ONE logo. Note: Center cap will have an inspection port IPO a logo if equipped with Stemco oil seals.
Rear axle (single) wheel simulator kit. Includes full stainless steel wheel simulators with integrated lug nut covers and E‐ONE logo.
Dura‐Brite finish on aluminum wheel (EA). Not available on 13" wheel (425 and 445 tires).
Freightliner chassis rims painted job color. Tradition.
Freightliner provided polished aluminum wheels.
International chassis rims painted job color. Tradition.
International chassis Rims Aluminum. Tradition.
Steel wheels for rear axle (4) 24" split rim.
Polish inner and outer aluminum wheel (EA).
Freightliner provided Front and Rear Wheel Brake Dust Shields
PRICE
$1,442.00
$7,849.00
$264.00
$325.00
$723.00
$1,281.00
$1,916.00
$2,553.00
$133.00
$262.00
$701.00
$186.00
$186.00
$264.00
$325.00
$723.00
$1,906.00
$325.00
$633.00
$923.00
$120.00
$0.00
$1,191.00
$0.00
$1,150.00
$7,459.00
$98.00
$80.00
Option No.
Description
PRICE
1050‐0043
1050‐0044
1050‐0045
1050‐0046
1050‐0047
1050‐0048
1050‐0049
1050‐0050
1050‐0051
1050‐0052
1050‐0053
1050‐0054
1050‐0055
1050‐0056
1050‐0057
1050‐0058
1050‐0059
1050‐0060
1050‐0061
1050‐0062
1050‐0063
1050‐0064
1050‐0065
1050‐0066
1050‐0067
Rear axle (tandem) wheel simulator kit. Includes full stainless steel wheel simulators with integrated lug nut covers and E‐ONE logo.
Accuride aluminum wheels for front axle (2).
Accuride aluminum wheels for rear axle (4).
Accuride aluminum wheels for rear axles (8).
Front axle wheel trim kit. Includes stainless steel "Cover‐Up" covers with E‐ONE logo. Not available with Stemco oil seals.
Rear axle (single) Wheel Trim kit. Includes stainless steel "Cover‐Up" covers with E‐ONE logo. Not available with Stemco oil seals.
Rear axle (tandem) Wheel Trim kit. Includes stainless steel "Cover‐Up" covers with E‐ONE logo.
Commercial chassis rims painted job color. For use with single rear axle.
International chassis rims aluminum. For use with single rear axle.
International chassis rims painted job color. For use with tandem rear axle.
International chassis rims aluminum. For use with tandem rear axle.
Crossfire dual wheel air tire equalizing system.
Six (6) steel wheels for front and rear axle tire package. Outboard wheels (outboard side only) are painted job color. Custom ES.
Six (6) aluminum wheels for front and rear axle tire package. Custom ES.
Wheel trim package. For use with steel or aluminum wheels. Custom ES.
Chassis rims painted job color.
Freightliner aluminum wheels.
International aluminum wheels.
The front and rear axle outboard steel rims to have painted trim. Color to be silver.
Navistar chassis rims painted job color, Wildland.
Navistar chassis rims polished aluminum, Wildland.
Navistar spare wheel/tire polished aluminum, Wildland.
Navistar spare wheel/tire painted steel, Wildland.
Kenworth aluminum wheels. For use with tandem rear axle.
Wheel check loose lug nut indicators (high temp orange) for 4x2/4x4 chassis. Front and rear wheels.
Each outboard facing wheel of the single axle unit shall have valve stem extensions; front 2", rear appropiately sized. Includes additional set (inside and outside) ship loose.
Isolators between wheels and/or hubs.
Accuride aluminum wheels outer and steel inner for rear axles (4).
Wheel check loose lug nut indicators (standard temperature lime green) for 4x2/4x4 chassis. Front and rear wheels.
Wheel simulator kit. Front & rear axle wheel simulator kit. Includes stainless steel wheel simulator and center cap with E‐ONE logo where
applicable.
Wheel trim package. For use with steel or aluminum wheels.
Lug nut Disc‐Lock (40) per unit. Model NMF‐2090‐M‐GEO.
Freightliner chassis rims aluminum. For use with tandem rear axle.
Accu‐Shield finish on aluminum wheel (EA). Not available on 13" wheel (425 and 445 tires).
$1,843.00
$1,910.00
$3,811.00
$7,618.00
$339.00
$435.00
$868.00
$0.00
$1,402.00
$0.00
$1,948.00
$347.00
$0.00
$2,474.00
$393.00
$0.00
$1,206.00
$1,218.00
$127.00
$0.00
$1,150.00
$897.00
$703.00
$2,093.00
$157.00
1050‐0068
1050‐0069
1050‐0070
1050‐0071
1050‐0072
1050‐0073
1050‐0074
1050‐0075
1050‐0076
$260.00
$228.00
$2,268.00
$157.00
$1,094.00
$492.00
$332.00
$0.00
$123.00
Option No.
1050‐0077
1050‐0078
1050‐0079
1050‐0080
1050‐0081
1050‐0082
1050‐0083
1060‐0001
1060‐0004
1060‐0005
1060‐0006
1060‐0007
1060‐0008
1060‐0009
1060‐0010
1060‐0015
1060‐0016
1060‐0017
1060‐0020
1060‐0021
1060‐0022
1060‐0023
1060‐0026
1060‐0030
1060‐0033
1060‐0042
1060‐0043
1060‐0044
1060‐0046
1060‐0047
1060‐0048
1060‐0049
1060‐0050
1060‐0051
1060‐0052
Description
Wheel check loose lug nut indicators (blue) for 4x2/4x4 chassis. Front and rear wheels.
Front axle wheel trim. Includes center cap with E‐ONE logo only; NO lug nut covers. Note: Center cap will have an inspection port IPO a logo if equipped with Stemco oil seals.
Rear axle (single) wheel trim. Includes center cap with E‐ONE logo only; NO lug nut covers.
Trim Kit, Lug nut covers for front and rear axle wheels. Includes lug nut covers only (chrome plated plastic if applicable)
Rear wheels to be 9 inches wide, quantity (4).
Alcoa aluminum wheels outer and steel inner for rear axles (8).
Alcoa aluminum wheels outer and steel inner for rear axles (4).
Two Michelin 315 tires model XZA‐1 for front axle.
Four Michelin 11R tires model XZE2 highway tread for rear axle.
Four Michelin 12R tires model XZE highway tread for rear axle.
Four Michelin 315 tires model XZA‐1 for rear axle
Eight Michelin 11R tires model XZE2 for rear axles.
Eight Michelin 12R tires model XZE for rear axles
Eight Michelin 315 tires model XZA‐1 for rear axles.
Two Goodyear 315 tires model G291 for front axle.
Four Michelin 11R rear tires with XDN2 all weather tread.
Four Michelin 12R rear tires with XDN2 all weather tread.
Four Michelin 315 rear tires with XDN2 all weather tread.
Four Goodyear 315 rear tires with mud and snow tread. Intermittent fire service rating if GAWR is over 29,560.
Eight Michelin 11R rear tires with XDN2 all weather tread.
Eight Michelin 12R rear tires with XDN2 all weather tread.
Eight Michelin 315 rear tires with Mud and Snow tread
Eight Goodyear 315 rear tires with Mud and Snow tread. Intermittent fire service rating if GAWR is over 59,120.
Four Goodyear 315 rear tires with G291 highway tread.
Eight Goodyear 315 rear tires with G291 highway tread.
Two Michelin 365 tires model XZA for front axle. Speed rating for up to 75 mph. Requires Alcoa alum wheels.
Two Michelin 425 tires model XZY3 for front axle.
Two Michelin 445 tires model XZY3 for front axle.
Two Michelin 425 tires model XFE for front axle.
Two Michelin 385 tires model XFE for front axle.
Four Michelin 12.00 x 24 tires model XZY LRH for rear axle. Note: Tires have an operating restriction per Michelin bulletin MSPN29163 (maximum one‐way distance of 50‐miles with a one (1) hour cool down).
Tyron tire pressure monitoring system model TPMS. Includes wireless remote display in cab.
Tire pressure monitoring valve stem caps.
Two Michelin 385 tires model XZY3 for front axle.
Eight Michelin 275/80R tires model XZE2 for rear axles.
PRICE
$157.00
$244.00
$304.00
$203.00
$495.00
$4,650.00
$2,325.00
$1,939.00
$3,332.00
$3,897.00
$3,876.00
$6,659.00
$7,792.00
$7,754.00
$1,939.00
$3,740.00
$4,262.00
$4,672.00
$4,060.00
$7,481.00
$8,523.00
$9,342.00
$8,118.00
$3,876.00
$7,754.00
$1,981.00
$2,398.00
$2,320.00
$2,489.00
$2,297.00
$4,569.00
$1,251.00
$183.00
$2,259.00
$6,435.00
Option No.
1060‐0053
1060‐0054
1060‐0055
1060‐0056
1060‐0057
1060‐0058
1060‐0059
1060‐0060
1060‐0061
1060‐0062
1060‐0063
1060‐0064
1060‐0065
1060‐0066
1060‐0067
1060‐0068
1060‐0069
1060‐0070
1060‐0071
1060‐0072
1060‐0073
1060‐0074
1060‐0075
1060‐0076
1060‐0077
1060‐0078
1060‐0079
1060‐0080
1060‐0081
1060‐0082
1060‐0084
1060‐0085
1060‐0086
1060‐0087
1060‐0088
Description
PressurePro tire pressure monitoring system for single rear axle units. Includes bail mounted display in cab.
PressurePro tire pressure monitoring system for tandem rear axle units. Includes bail mounted display in cab.
Tire pressure monitoring valve stem caps. For use with a chassis with 14K front and 26K rear axle.
Tire pressure monitoring valve stem caps. For use with a chassis with 14K front and 30K rear axle.
Tire pressure monitoring valve stem caps. For use with a chassis with 18K front and 40K tandem rear axle.
Tire pressure monitoring valve stem caps. For use with a chassis with 18K front and 46K tandem rear axle.
Tire pressure monitoring valve stem caps. For use with a chassis with 20K front and 46K tandem rear axle.
Two Michelin 315 tires model XZY3 for front axle.
Four Michelin 12R rear tires with Mud and Snow XDS tread
Front and rear axle tire package. Includes two (2) Michelin 315 XZA‐1 front tires and four (4) Michelin 11R XZE rear tires with highway tread. Custom ES.
Front and rear axle tire package. Includes two (2) Michelin 315 XZA‐1 front tires and four (4) Michelin 11R XDN rear tires with mud and snow tread. Custom ES.
Tire pressure monitoring valve stem caps. Custom ES.
Tire pressure monitoring valve stem caps.
Tire pressure monitoring valve stem caps. For use with a chassis with 12K front and 23K rear axle.
Tire pressure monitoring valve stem caps. For use with a chassis with 12K front and 26K rear axle.
Tire pressure monitoring valve stem caps. For use with a chassis with 12K front and 24K rear axle.
Tire pressure monitoring valve stem caps. For use with a chassis with 14K front and 24K rear axle.
Tire pressure monitoring valve stem caps. For use with a chassis with 14K front and 26K rear axle.
Tire pressure monitoring valve stem caps. For use with a chassis with 16K front and 30K rear axle.
Two Goodyear 385 tires for front axle with G296 MSA highway tread.
Two Goodyear 425 tires for front axle.
Two Goodyear 445 tires for front axle
Four Goodyear 11R rear tires with G622 RSD mud and snow tread.
Four Goodyear 12R rear tires with mud and snow tread.
Eight Goodyear 11R rear tires with G622 RSD Mud and Snow tread.
Eight Goodyear 12R rear tires with Mud and Snow tread
Four Goodyear 11R rear tires with highway tread
Eight Goodyear 11R rear tires with highway tread.
PressurePro tire pressure monitoring system for single rear axle units. Includes electrical system integrated display in cab.
Tire pressure monitoring valve stem caps. For use with a chassis with 16K front and 30K rear axle.
Tire pressure monitoring valve stem caps. For use with a chassis with 14K front and 40K tandem rear axle.
Eight Michelin 12R rear tires with Mud and Snow XDS tread
Four Goodyear 11R rear tires with G287 MSA highway tread
Two Goodyear 315 tires with G287 MSA tread for front axle
Tire pressure monitoring valve stem caps. For use with a chassis with 20K front and 40K tandem rear axle.
PRICE
$1,064.00
$1,273.00
$0.00
$50.00
$67.00
$67.00
$67.00
$2,083.00
$3,520.00
$0.00
$96.00
$0.00
$0.00
$0.00
$0.00
$0.00
$0.00
$0.00
$67.00
$2,222.00
$2,163.00
$2,341.00
$4,114.00
$4,687.00
$8,229.00
$9,376.00
$2,978.00
$5,952.00
$1,064.00
$50.00
$67.00
$7,032.00
$2,978.00
$1,869.00
$159.00
Option No.
1060‐0089
1060‐0090
1060‐0091
1060‐0092
1060‐0095
1060‐0096
1060‐0097
1060‐0098
1060‐0099
1060‐0100
1060‐0103
1060‐0104
1060‐0105
1060‐0106
1060‐0107
1060‐0108
1060‐0109
1060‐0111
1060‐0112
1060‐0113
1060‐0114
1060‐0116
1060‐0117
1060‐0118
1060‐0119
1060‐0120
1060‐0121
1060‐0123
1060‐0124
1060‐0127
1060‐0129
1060‐0130
1060‐0131
1060‐0132
1060‐0133
Description
Front tires to be Bridgestone that are sized for the axle capacity provided.
Rear tandem axle tires to be Bridgestone mus and snow that are sized for the axle capacity provided.
Tire pressure monitor display is to be located on the [#LOC].
Eight Michelin 275/80R22.5 rear tires with Mud and Snow tread.
Eight Goodyear 315 rear tires with G287 MSA highway tread.
Tire balancing (EA). Location: front tires.
Eight Michelin 315 tires model XZU‐S2 for rear axles
Two Bridgestone 315 tires model M860 for front axle.
Four Bridgestone 12R tires model R250F highway tread for rear axle.
Front and rear axle tire package. Includes two (2) Michelin 385 XFE front tires and four (4) Michelin 11R XDN rear tires with mud and snow tread. Custom ES.
Cat's Eye model 6130‐AB00 single rear axle tire pressure monitoring system. For use on 130 PSI tires. Includes braided lines.
Four Goodyear 12R rear tires with G661 HSA highway tread.
Eight Goodyear 12R rear tires with G661 HSA highway tread.
Four Goodyear 11R rear tires with G661 HSA highway tread.
Eight Goodyear 11R rear tires with G661 HSA highway tread.
Tire pressure monitoring valve stem caps. For use with a chassis with 14K front and 23K rear axle.
Eight Michelin 295/80R tires model XZA2 for rear axles.
Four Goodyear 315 rear tires with G289 WHA tread.
Tire pressure monitoring valve stem caps. Real Wheels LED indicators.
Intermittent service tire rating.
Tire pressure monitoring valve stem caps. VECSAFE LED indicators.
Vogel Lube display is to be located on the [#LOC].
RWC AirGuard LED tire pressure monitoring valve stem caps (6) for single rear axle applications.
RWC AirGuard LED tire pressure monitoring valve stem caps (8) for Tiller applications.
RWC AirGuard LED tire pressure monitoring valve stem caps (10) for tandem rear axle applications.
Two Goodyear 315 front tires with G289 WHA tread.
Four Goodyear 11R rear tires with RHD‐II G137 tread.
RWC AirGuard LED tire pressure monitoring valve stem caps (2) front only. For use with rear axle Crossfire equalization systems.
Four Michelin 11R rear tires with XDS2 mud and snow tread.
Four Goodyear 11R rear tires with G751 MSA highway tread
Tire pressure monitoring integrated with V‐MUX multiplex electrical system. Includes wheel mounted sensors. Requires Vista display. For use with tandem rear axle units.
Four Michelin 12R rear tires with XZY3 tread.
Two Michelin 425 tires model XZL for front axle.
Four Goodyear 12R rear tires with G751 MSA highway tread.
Michelin tires for commercial chassis Freightliner M2
PRICE
$0.00
$0.00
$0.00
$6,844.00
$7,861.00
$72.00
$8,891.00
$2,728.00
$4,457.00
$208.00
$890.00
$3,032.00
$6,061.00
$2,817.00
$5,632.00
$0.00
$7,324.00
$4,236.00
$244.00
$0.00
$244.00
$0.00
$188.00
$251.00
$299.00
$2,119.00
$3,682.00
$76.00
$3,740.00
$2,978.00
$1,826.00
$4,900.00
$2,398.00
$3,520.00
$0.00
Option No.
1060‐0134
1060‐0135
1060‐0136
1070‐0001
1070‐0002
1070‐0003
1070‐0004
1070‐0005
1070‐0007
1070‐0011
1070‐0012
1070‐0013
1070‐0014
1070‐0015
1070‐0016
1070‐0017
1070‐0018
1070‐0019
1070‐0020
1070‐0021
1070‐0022
1070‐0024
1070‐0025
1070‐0026
1070‐0027
1070‐0028
1070‐0029
1070‐0030
1070‐0031
1070‐0032
1100‐0000
1100‐0001
1100‐0002
Description
Four Michelin 315 rear tires with XZY3 tread.
Eight Michelin 315 rear tires with XDY tread.
Two Michelin 425 tires model XZU S wide base for front axle.
Rear suspension springs rated equal to the capacity of the axle.
Rear suspension springs rated equal to the capacity of the axles.
Rear suspension air ride rated equal to the capacity of the axle.
Rear suspension air ride (40‐46K) rated equal to the capacity of the axles.
Air ride cab.
Shock absorbers rear single axle. Not available on 31,000 lb.
Ridewell Dynalastic 62,000 lb rear suspension. C‐Frame applications only.
Reyco rear suspension springs rated equal to the capacity of the axle.
Rear suspension air ride (48‐54K) rated equal to the capacity of the axles.
Rear suspension air ride (60‐62K) rated equal to the capacity of the axles.
Ridewell Dynalastic rear suspension (40‐54K) rated equal to the capacity of the axles.
The rear suspension to be for a 24,000lbs. application IPO 27,000lbs.
Reyco rear spring suspension w/aux 33K rating.
Suspension spacers to be held at a minimum to keep OAH as low as possible.
Rear suspension springs rated at 27,000 lbs.
Rear axle u‐bolts .875". 24K/27K rear axles only. Not available with air ride suspensions.
Rear suspension FIREMAAX EX air ride (50‐54K) rated equal to the capacity of the axles. Requires TB modification on 4‐jack aerials. (Raises OAH .5" over springs)
Rear suspension FIREMAAX EX model FMX‐482 air ride rated equal to the capacity of the axles (40‐48K). Requires TB modification on 4‐
jack aerials. (Raises OAH .5" over springs)
Lower leaf wrap. Single rear axle only.
Reyco rear axle shocks and anti‐roll bar. Available on up to 26K rear axle.
Rear axle shocks for Reyco single axle rear suspension.
Rear suspension FIREMAAX EX model FMX‐272 27,000 lb. single axle air ride.
Rear suspension FIREMAAX EX model FMX‐242 24,000 lb. single axle air ride.
Rear suspension FIREMAAX EX model FMX‐312 31,000 lb. single axle air ride. Requires aluminum wheels.
Rear suspension FIREMAAX EX model FMX‐622 air ride (60‐62K) rated equal to the capacity of the axles. Requires alum wheels. Requires TB modification on 4‐jack aerials. (Raises OAH .5" over springs)
Front axle u‐bolts .875". Not available with independent suspensions.
Rear suspension Link Atlas 33,000 ‐ 35,000 lb. single axle air ride. Requires DANA axle and aluminum wheels. Not compatible with tire chains.
16‐1/2'' x 6'' S‐cam brakes with ArvinMeritor automatic slack adjusters for front axle.
Meritor EX225H 17" disc brakes for front axle.
ArvinMeritor 16‐1/2'' x 7'' S‐cam brakes with cast brake drums for a single rear axle.
PRICE
$4,672.00
$9,505.00
$2,398.00
$1,491.00
$4,668.00
$6,057.00
$10,557.00
$3,115.00
$208.00
$12,723.00
$1,491.00
$12,368.00
$14,276.00
$13,905.00
$0.00
$2,238.00
$0.00
$1,739.00
$117.00
$12,314.00
$11,318.00
$596.00
$1,735.00
$938.00
$6,508.00
$6,013.00
$8,524.00
$14,445.00
$117.00
$9,697.00
$341.00
$1,331.00
$341.00
Option No.
1100‐0003
1100‐0004
1100‐0005
1100‐0006
1100‐0007
1100‐0008
1100‐0009
1100‐0010
1100‐0011
1100‐0014
1100‐0015
1100‐0016
1100‐0017
1100‐0018
1100‐0019
1100‐0020
1100‐0022
1100‐0023
1100‐0024
1100‐0025
1100‐0026
1100‐0027
1100‐0028
1100‐0030
1100‐0031
1100‐0032
1100‐0033
1100‐0034
1100‐0035
1100‐0036
1100‐0037
1100‐0038
1100‐0040
1100‐0042
1100‐0043
1100‐0044
Description
Meritor EX225H 17" disc brakes for rear axle, maximum capacity 27,000 lbs.
Meritor EX225H 17" disc brakes for rear axles, maximum capacity 54,000 lbs.
Brake system air 4X2/4X4.
Parking brake release mounted on the driver's side lower dash.
Parking brake release mounted center of the engine cover.
Brake system air 6X4.
Front axle parking brake.
Brake emergency release for spring.
Roll Stability Control, Includes ATC. Not available on commercial chassis, tiller or tandem axle custom chassis.
ArvinMeritor 16‐1/2'' x 7'' S‐cam brakes with cast brake drums for a tandem rear axle.
Air brake system tractor/tiller ABS system for both tractor and tiller axle brakes.
16‐1/2'' x 6'' Q‐Plus S‐cam brakes with ArvinMeritor automatic slack adjusters for Tillerman steering axle.
(OBS) Meritor EX225H 17" disc brakes for Tillerman steering axle.
Dust Shields. Front and Rear Axle. CAM Brakes only.
Dust Shields. Rear Axle. CAM Brakes only.
Compression fittings for all air brake system lines. Includes cab interior air lines as applicable.
Dust Shields. Front and rear tandem axle. CAM brakes only.
Stainless steel park brake release guard.
G4 Electronic Stability Control (4x2), Includes RSC and ATC. Not available on 4x4, commercial chassis or tiller.
ArvinMeritor 16‐1/2'' x 8.625'' Q‐Plus S‐cam brakes with cast brake drums for a single rear axle. 24K axle only.
G4 Electronic Stability Control (6x4), Includes RSC and ATC. Not available on 6x6 or commercial chassis.
Knorr‐Bremse 17" disc brakes for front axle. Timoney IFS only.
ArvinMeritor 18'' x 7'' P‐Type S‐cam brakes with cast brake drums for a 33K single rear axle.
Brake chambers 30‐36 for 24,000# single rear axle. N/A with disc brakes.
Dana ADB22X 17" disc brakes for front axle.
Hinged stainless steel park brake release guard.
Bendix 16‐1/2'' x 7'' S‐cam brakes for 33,000 ‐ 35,000 Dana axle.
Brake chambers 30‐36 for 48K/54K tandem rear axle. N/A with disc brakes.
Glad Hands tow option. Location: Front chassis frame.
16.5'' x 8.625'' P‐Cast S‐cam brakes for 27,000 ‐ 33,000 Meritor axle.
Glad Hands tow option. Location: rear chassis frame.
Heavy duty 16‐1/2'' x 6'' S‐cam brakes with ArvinMeritor automatic slack adjusters for front axle. For use with 22,100 Meritor axle.
Gauge air brake application additional. Location: officer side overhead console.
Navistar ESP Stability control system, 4 x 4, Option, Wildland
Emergency park brake activation valve mounted on the officer's side dash with stainless steel guard.
Parking brake release mounted on the driver side elecrical access cover (side facing). Severe duty interior only.
PRICE
$1,331.00
$2,033.00
$8,994.00
$0.00
$347.00
$9,318.00
$570.00
$1,036.00
$2,153.00
$411.00
$9,195.00
$341.00
$1,331.00
$397.00
$242.00
$1,332.00
$636.00
$232.00
$3,787.00
$1,402.00
$4,515.00
$1,331.00
$2,458.00
$592.00
$1,331.00
$309.00
$341.00
$1,179.00
$581.00
$873.00
$581.00
$802.00
$331.00
$1,750.00
$720.00
$0.00
Option No.
1100‐0045
1100‐0046
1100‐0047
1100‐0048
1100‐0049
1100‐0051
1100‐0052
1100‐0053
1100‐0054
1100‐0055
1100‐0056
1100‐0057
1100‐0058
1100‐0059
1100‐0060
1100‐0061
1100‐0062
1100‐0063
1100‐0064
1100‐0065
1100‐0066
1100‐0067
1100‐0068
1110‐0000
1110‐0001
1110‐0002
1110‐0003
1110‐0004
1110‐0005
1110‐0006
1110‐0007
1110‐0008
1110‐0009
1110‐0010
Description
2nd parking brake release mounted on the officer's side electrical access cover (side facing) with stainless steel guard. Severe duty interior only.
Brake system air tank to be mounted as high as possible.
Navistar ESP (ESC) Stability control system 4 x 2
Emergency park brake activation valve mounted on the center console offset driver side with stainless steel guard.
Parking brake release mounted on center dash (not available with ABS dash).
Location the front axle parking brake shall be located: [#LOC].
G4 Electronic Stability Control with Wabco OnGuard CMS system (4x2). Includes RSC and ATC. Not available on 4x4, commercial chassis or tiller.
G4 Electronic Stability Control with Wabco OnGuard CMS system (6x4). Includes RSC and ATC. Not available on 4x4, commercial chassis or tiller.
Bendix SN7 17" disc brakes for front axle. Reyco Granning IFS only.
Spring guards on each end of brake lines from wheel to frame.
Parking brake release mounted on the driver's side of upper tier. Severe duty dash only.
Brake chambers to be type 24 front and 30/30 rear. MGM piston style long stroke.
Safety Check brake stroke indicators.
Stainless steel u‐bolt design park brake release guard.
Brake chambers on front axle to be type 24. MGM piston style long stroke.
Glad Hands tow option. Location: Front chassis frame, below gravel shield, driver side.
Locate front park brake control adjacent to rear park brake control ipos.
ArvinMeritor 16‐1/2'' x 8.625'' Q‐Plus S‐cam brakes with cast brake drums for a 48K tandem rear axle.
Glad Hands tow option. Location: Front chassis frame, below gravel shield, officer side.
Brake chambers 36‐36 for 27,000# single rear axle. N/A with disc brakes. Option limited to 20,000 front GAWR.
Emergency park brake activation valve mounted on the officer's side upper tier with stainless steel guard.
16‐1/2'' x 7'' S‐cam brakes with automatic slack adjusters for Marmon‐Herrington front drive axle.
Parking brake release to be mounted on the driver's side lower dash, centered on panel to right side of steering column.
Inlet for air system. Location: [#LOC].
Air inlet auto eject. Includes weatherproof gasketed cover. [#LOC].
Air dryer Bendix AD‐9.
Air dryer System Saver 1200.
Air tank drains w/pull cords.
Automatic moisture ejectors, heated.
Air lines nylon.
Air lines braided.
Gauge air brake application mounted in cab
Air horns on hood pair. Requires control.
Air inlet. To charge brake system. Commercial chassis only. Location: [#LOC].
PRICE
$968.00
$232.00
$1,760.00
$720.00
$337.00
$0.00
$8,019.00
$8,747.00
$1,331.00
$182.00
$0.00
$697.00
$770.00
$232.00
$349.00
$581.00
$0.00
$2,802.00
$581.00
$592.00
$720.00
$341.00
$0.00
$404.00
$520.00
$526.00
$633.00
$461.00
$458.00
$0.00
$2,452.00
$331.00
$655.00
$404.00
Option No.
1110‐0011
1110‐0012
1110‐0013
1110‐0021
1110‐0025
1110‐0026
1110‐0027
1110‐0034
1110‐0038
1110‐0039
1110‐0040
1110‐0041
1110‐0042
1110‐0043
1110‐0044
1110‐0045
1110‐0046
1110‐0048
1110‐0049
1110‐0050
1110‐0051
1110‐0052
1110‐0053
1110‐0054
1110‐0055
1110‐0056
1110‐0057
1110‐0058
1110‐0059
1110‐0060
1110‐0061
1110‐0062
1110‐0063
1110‐0064
Description
Air intake restriction gauge.
Air outlet off front ACC tank. It shall be located [#LOC].
Air horns shut‐off valve. Located in cab accessible by driver.
Auxiliary 1738 cubic inch air tank plumbed to vehicle air system.
Thomas 110 volt air compressor plumbed to air brake system.
Air horns recessed in bumper (PR).
Isolated air tank. Includes pressure protection valve.
Auxiliary air tank to be plumbed to the chassis air horns only.
Driver and officer side foot switch. Supplied by International. For use with recess bumper mounted air horns.
Driver and officer side foot switch. Supplied by Freightlinerl. For use with recess bumper mounted air horns.
Dump valve system for rear air ride suspension. Includes three valves, one on each bag and one on supply line. Switch from driver's side overhead console.
Air horns Grover recessed in bumper (PR).
Label on isolated air tank "Air Horns Only".
Auxiliary air tank to be plumbed to the following optional accessories (if equipped): Chassis air horns, brake system air outlet, air reel, light tower, air primer and or customer/dealer supplied pneumatic add‐on(s).
Air inlet Auto‐Eject. Includes [#COL] weatherproof gasketed cover. Location: [#LOC].
Gast air compressor 110v model 3HBB‐32‐M300AX.
Kussmaul 12V Auto Drain. For use with Kussmaul air compressor.
Air inlet below bumper driver side. Fitting to be a Hansen male model B40 with protective plastic cover. Includes matching female model 4000 fitting (ship loose).
Air Lines Wrapped in Thermal Loom
Air brake lines to have 4 to 6'' slack for future service work.
Tilt air horns down due to freezing conditions.
Air horns recessed behind bumper (PR). Includes E‐ONE grilles on bumper.
Air horns Grover recessed in front bumper. (1) air horn 21" long, (1) air horn 24.5" long
Relocate air dryer to opposite the exhaust system inside the frame rails.
Air horns will alternate from driver to officer.
Air dryer Bendix ADIP.
Air outlet plumbed to vehicle air system. It shall be located [#LOC].
Air horns recessed in bumper (PR) with bells behind bumper.
Air horns Grover (1510) recessed in bumper (PR). Locate both to driver side of bumper.
Dual Grover Hood Mounted Air Horns with Driver and Officer Foot Switches to be Supplied and Installed by Freightliner. Tradition
Dual Grover hood mounted air horns with driver and officer foot switches to be supplied and installed by Freightliner.
Dual Hadley Hood Mounted Air Horns with Driver and Officer Foot Switches to be Supplied and Installed by International.
Dual Grover Hood Mounted Air Horns with Driver and Officer Foot Switches to be Supplied and Installed by International. Tradition
Dual Hadley Hood Mounted Air Horns with Driver and Officer Foot Switches to be Supplied and Installed by International.
PRICE
$282.00
$404.00
$119.00
$541.00
$1,263.00
$896.00
$609.00
$0.00
$0.00
$0.00
$696.00
$1,091.00
$36.00
$0.00
$520.00
$1,167.00
$506.00
$520.00
$1,985.00
$122.00
$0.00
$1,127.00
$1,142.00
$292.00
$434.00
$676.00
$404.00
$959.00
$1,119.00
$695.00
$0.00
$825.00
$875.00
$0.00
Option No.
1110‐0065
1110‐0066
1110‐0067
1110‐0068
1110‐0069
1110‐0070
1110‐0074
Description
Dual Grover hood mounted air horns with driver and officer foot switches to be supplied and installed by Navistar.
Air horns Grover recessed in front bumper. (1) air horn 21" long, (1) air horn 24.5" long.
Auxiliary air tanks (2) on Tiller trailer to be plumbed to the air reel only.
Dual Grover Hood Mounted Air Horns with Driver and Officer Foot Switches to be Supplied and Installed by E‐One.
Dual Grover hood mounted air horns with Y lanyard between driver and officer. This shall be supplied and installed by Navistar.
Dual Hadley Hood Mounted Air Horns with Y lanyard switch in overhead between Driver and Officer seating positions tol be Supplied and Installed by International.
Air horns Grover mounted to hood each side. (1) air horn 21" long, (1) air horn 24.5" long.
1110‐0087
1110‐0089
1110‐0090
Dual Stuttertone Hood Mounted Air Horns with Driver and Officer Foot Switches to be Supplied and Installed by Freightliner. Tradition
Dual Stuttertone hood mounted air horns with driver and officer foot switches to be supplied and installed by Freightliner.
Recessed air outlet off isolated tank. Location: [#LOC].
Omit the Hood Mounted Air Horns and install the Air Horn plumbing only with Driver and Officer Foot Switches to be Supplied and Installed by Freightliner. Tradition
Dual Hadley air horns mounted in front bumper extension. For use with driver and officer foot switches supplied and installed by International. Tradition
Dual foot switches. Locate (1) driver and (1) officer. To be supplied by International. For use with E‐ONE installed air horns in bumper extension.
Air horns Grover model 2040 rectangular recessed in bumper (PR) with snow caps.
Dual Hadley Hood Mounted Air Horns with Driver Foot Switch and Center Dash Mounted Push Button to be Supplied and Installed by International. Tradition
Airhorns to be recessed flush (as applicable) with exterior of bumper.
Bumper mounted Grover 21" air horns. Controls required and provided separately.
Locate driver side air tank to rear of battery tray.
Air inlet. To charge brake system. Commercial chassis only. Inlet to be located within the cab and accessable from the driver side door area.
Single Grover 1512 air horn, steering wheel and officers foot switch controlled, Wildland
Air horns Grover recessed in bumper (PR) with snow caps.
1110‐0091
1110‐0092
1110‐0093
1110‐0094
1110‐0095
1110‐0096
1110‐0097
1110‐0098
Dual Grover hood mounted air horns with driver and officer foot switches to be supplied and installed by Navistar, Option, Wildland
Air tank manual drains shall have cables routed to the outside of the apparatus and labeled accordingly.
A momentary switch to activate air horns shall be mounted on the center console in easy reach of the officer.
A switch dedicated to the emergency amber lights shall be mounted on the cab interior instrument panel.
Automatic moisture ejector, heated. Wet tank only.
Stainless steel mounting straps for air tank.
Automatic moisture ejector, non‐heated (EA).
All manual air tank drains to be at 45 degree or 90 degree angle as required.
1110‐0075
1110‐0076
1110‐0077
1110‐0078
1110‐0080
1110‐0081
1110‐0082
1110‐0083
1110‐0084
1110‐0085
1110‐0086
PRICE
$0.00
$1,339.00
$0.00
$1,091.00
$0.00
$0.00
$1,342.00
$726.00
$0.00
$404.00
$695.00
$335.00
$275.00
$1,163.00
$610.00
$0.00
$942.00
$0.00
$404.00
$714.00
$1,230.00
$1,426.00
$100.00
$78.00
$78.00
$197.00
$160.00
$151.00
$0.00
Option No.
1110‐0099
1110‐0100
1110‐0101
1110‐0102
1110‐0103
1110‐0104
1110‐0105
1110‐0106
Description
Air dryer System Saver Twin.
Auxiliary air tank system. Total reservoir capacity to be 11,585 cubic inches or greater (including brakes). Includes pressure protection valves as applicable. Airhorns and outlets plumbed to system.
Locate air horns officer side (1) inboard, (1) outboard of framerails.
Thomas 220 volt air compressor plumbed to air brake system.
Martin‐Horn No. 2297 GM. Includes set of (4) horns, air compressor and snow caps for horns. Locate horns below front bumper and compressor below rear bench seat. Horn compressor to be activated through switch in multiplex display.
Air horns Grover (1510) recessed in bumper (PR). Locate one each side outboard of frame.
Gast air compressor 120V/240V model 4HCC‐10‐M450X.
Air horns Grover recessed behind bumper (PR). Includes E‐ONE grilles on bumper.
1110‐0112
1110‐0113
1110‐0114
The standard air brake release mounted on the center console shall be upgraded to include auxiliary tank release to brakes for emergency PSI buildup/brake release. A separate pressure gauge shall be mounted on the dash to indicate auxiliary air tank pressure.
Rubber cover for air outlet. Includes mechanical fastener for securing of cover.
Air hose routed from the compressor to the dryer shall be upgraded to include stainless steel mesh for the full length of hose.
Dual Stuttertone hood mounted air horns with driver and officer foot switches to be supplied and installed by Freightliner.
Gast air compressor 110v model 1HAB‐10‐M100X.
Martin‐Horn No. 2297 GM. Includes set of (4) horns, air compressor and snow caps for horns. Locate horns and compressor in cab. Horn compressor to be activated through switch in cab accessible to the driver.
Dual Grover hood mounted air horns with a driver side foot switch to be supplied and installed by Navistar.
Dual Hadley Hood Mounted Air Horns with Driver side steering wheel switch to be Supplied and Installed by International.
1110‐0115
1110‐0116
1110‐0117
1110‐0118
1110‐0119
Dual Grover hood mounted air horns with two (2) position horn ring switch DOT horn/air horn, to be supplied and installed by Navistar.
Air horns Buell recessed in bumper (PR).
Air horns Grover model 2040 rectangular recessed in bumper (PR).
Inlet for air system. Includes weather proof box and Hubbel [#COL] cover. Location: [#LOC].
Isolated air tank. Includes pressure protection valve. International chassis only.
1110‐0120
Dual Stuttertone hood mounted air horns with dual lanyard control switches in overhead to be supplied and installed by Freightliner.
Stuttertone air horns on commercial hood pair. Horns to be mounted to side of commercial chassis hood. Does not include foot switch(s).
Dual Grover Hood Mounted Air Horns with E‐ONE supplied activation to be Supplied and Installed by International. Tradition
Dual Stuttertone Hood Mounted Air Horns to be Supplied and Installed by Freightliner. Lanyard activation sold separately. Tradition
Air horns Grover recessed behind bumper (PR). Includes grilles (No Logo) on bumper.
Gast air compressor 110v model 3HBB‐32‐M300AX with moisture filter.
Air horns (pair) includes isolated 12V pump, tank, (2) switches: driver side foot & officer side push button on officer side of center console. Horns to be located: below front bumper between frame rails.
1110‐0107
1110‐0108
1110‐0109
1110‐0110
1110‐0111
1110‐0121
1110‐0122
1110‐0123
1110‐0124
1110‐0125
1110‐0126
PRICE
$1,174.00
$2,430.00
$0.00
$1,263.00
$5,687.00
$1,119.00
$1,355.00
$1,323.00
$649.00
$19.00
$85.00
$0.00
$1,072.00
$5,687.00
$0.00
$0.00
$0.00
$1,137.00
$1,163.00
$515.00
$100.00
$0.00
$0.00
$765.00
$610.00
$1,323.00
$1,328.00
$2,750.00
Option No.
1110‐0127
1110‐0128
1110‐0129
1110‐0130
1110‐0131
1110‐0132
1110‐0133
1110‐0134
1110‐0135
1110‐0136
1110‐0137
1110‐0138
1110‐0139
1110‐0140
1110‐0141
1110‐0142
1110‐0143
1110‐0144
1110‐0145
1110‐0146
1110‐0147
1110‐0148
1110‐0149
1110‐0150
1125‐0000
1125‐0001
1125‐0002
1125‐0003
1125‐0006
1125‐0007
1125‐0009
Description
Automatic moisture ejector, heated. Air dryer only.
Gauge air for tank. Location: driver side overhead.
Diamond plate flip cover for air inlet or outlet with label mounted in driver's door jamb.
Dual Stuttertone hood mounted air horns with driver foot switch to be supplied and installed by Freightliner. See options for additional switches as applicable to be E‐ONE added.
Compression fittings for fan clutch ipos.
Air tank drains w/pull cords. Ends of pulls to be labeled with tank type and drain sequence.
Air dryer Haldex model N4253A.
Auxiliary air tanks to be plumbed to the following optional accessories (if equipped): Air reel, light tower and or customer/dealer supplied pneumatic add‐on(s).
Air horns shut‐off valve. Located on driver side overhead console.
Air horns shut‐off valve. Located on officer side overhead console.
Compression fittings for pump shift ipos.
Air horns Grover model 2040 rectangular behind bumper (PR). Includes E‐ONE grilles.
Air dryer Bendix AD‐SP.
Locate air horns outside of frame rails.
Air inlet shut‐off valve. Located adjacent to air inlet.
Brake system air tank drains located in (1) central location at rubrail.
Diamond plate flip cover for air inlet or outlet with label mounted on officer's gravel shield.
Air outlet shut‐off valve. Located adjacent to air outlet.
Switch. Foot switch siren break. Includes: 25 degree mounting bracket. See photo on file for mounting instructions. Locate (1) officer side for left foot.
Dual Stuttertone hood mounted air horns with driver and officer foot switches to be supplied and installed by Kenworth.
Recessed air outlet off isolated tank. Location: driver and officer side rear wheel well offset rearward.
Locate air horns driver side (1) inboard, (1) outboard of framerails.
Drain. Manual drain for Atlas compressor. Locate at rubrail adjacent to compressor on officer side of body.
Parker model DCR601‐4 air tank drains ipos (EA).
Retarder Telma focal mounted. All four stages applied with brake application. Not available on tandem axle or four jack aerials.
Brake Jacob's exhaust
Jacobs engine compression brake.
Allison transmission retarder. Pre‐select feature will be switched off with this option.
Driveline Mounted Telma Retarder. Standard switch location is on console, manual lever on engine cover offset to driver's side. Cut off at 5 mph ‐ 25% applied with throttle release & balance with brake application.
Tag located at Jacob Brake Controller. To read: Do Not Operate on Wet or Slippery Surfaces.
Allison retarter to activate per Seattle requirements. Dash label "Switch Retarter Off for Wet or Slippery Road Conditions. Retarder shall activate 30% at zero throttle with the remaining 70% applied sequentially through the brake pedal. The brake/stop light circuit shall activate with retarder application.
PRICE
$197.00
$426.00
$125.00
$0.00
$116.00
$461.00
$717.00
$0.00
$119.00
$119.00
$116.00
$1,395.00
$526.00
$0.00
$119.00
$0.00
$125.00
$119.00
$150.00
$0.00
$404.00
$0.00
$0.00
$58.00
$10,952.00
$817.00
$1,897.00
$12,978.00
$10,952.00
$86.00
$324.00
Option No.
1125‐0010
1125‐0011
1125‐0012
1125‐0013
1125‐0014
1125‐0015
1125‐0016
1125‐0017
1125‐0018
1125‐0019
1125‐0020
1125‐0021
1125‐0022
1125‐0023
1125‐0024
1125‐0025
1125‐0026
1150‐0007
1150‐0008
1150‐0009
1150‐0010
1150‐0011
1150‐0012
1150‐0013
1150‐0014
1150‐0015
1150‐0019
1150‐0020
1150‐0021
Description
Allison transmission retarder to be programmed at 1/3 off throttle, 1/3 at 4 psi brake pressure, 1/3 at full (10 psi) brake pressure.
Allison transmission retarder to be programmed at 1/3 at 4 psi brake pressure, 1/3 at 7 psi brake pressure, 1/3 at full (10 psi) brake pressure.
Driveline Mounted Telma Retarder. All four stages applied with brake application.
Lever control for Telma retarder. 5 position lever with low speed cutout.
Dual retarder operation. Engine Jacobs brake and transmission retarders to both be operable at the same time. Requires special approval. Option contingent on receiving formal approval from driveline component suppliers.
Relocate Jake Brake control to driver side of electrical access cover.
Allison transmission retarder.
Transmission to seek 3rd gear when Jacobs Compression brake is engaged. Requires special approval. Option contingent on receiving formal approval from driveline component suppliers.
Compression brake for MAXXFORCE engines.
Driveline Mounted Telma Retarder. Stage 1 & 2 applied off throttle; stage 3 & 4 applied with brake application.
Jacobs engine compression brake. To be controlled only by a single on/off sw.
Driveline Mounted Telma Retarder to operate w/ 5 position lever within cab. 5 position lever sold separately.
Driveline Mounted Telma Retarder. Stage 1 applied off throttle; stage 2, 3 & 4 applied with brake application.
Transmission to seek second gear when Jacobs engine brake or Telma retarder is engaged. N/A with Trans retarder.
Switch selector Jacobs compression brake / transmission retarder. Location and function: driver side overhead console to select compression brake or trans retarder.
Relocate Jacobs Brake control. Location: driver side of center dash upper tier.
Relocate Jacobs Brake control. Location: driver side, side facing, adjacent to Vista Display.
Tray center of bumper with slats 34x13x10 for 149 feet of 1‐3/4" double jacket hose or 57 feet of 5" LDH.
Tray center of bumper with slats 34x13x12 for 182 feet of 1 3/4" double jacket hose or 70 feet of 5" LDH
Tray center of bumper with slats 34x13x14 for 216 feet of 1 3/4" double jacket hose or 83 feet of 5" LDH
Tray center of bumper with slats 34x13x10 with divider running front to back
Tray center of bumper with slats 34x13x12 with divider running front to back
Tray center of bumper with slats 34x13x14 with divider running front to back
Tray center of bumper with slats 34x13x10 with divider running side to side
Tray center of bumper with slats 34x13x12 with divider running side to side
Tray center of bumper with slats 34x13x14 with divider running side to side
Tray driver side bumper outboard with slats 17x9x10 for 51feet of 1 3/4" double jacket hose. For use when the tow eyes are mounted in the up position.
Tray driver side bumper outboard with slats 17x9x12 for 63 feet of 1 3/4" double jacket hose. This tray is for use when the tow eyes are mounted in the up position.
Tray driver side bumper outboard with slats 17x9x14 for 74 feet of 1 3/4" double jacket hose. This tray is for use when the tow eyes are mounted in the up position.
PRICE
$0.00
$0.00
$10,952.00
$318.00
$131.00
$432.00
$11,290.00
$131.00
$1,897.00
$10,952.00
$1,897.00
$10,952.00
$10,952.00
$0.00
$218.00
$432.00
$432.00
$737.00
$737.00
$737.00
$737.00
$737.00
$737.00
$737.00
$737.00
$737.00
$674.00
$674.00
$674.00
Option No.
1150‐0022
1150‐0023
1150‐0024
1150‐0028
1150‐0029
1150‐0030
1150‐0031
1150‐0032
1150‐0033
1150‐0034
1150‐0035
1150‐0036
1150‐0037
1150‐0038
1150‐0040
1150‐0041
1150‐0042
1150‐0043
1150‐0047
1150‐0049
1150‐0050
1150‐0051
1150‐0052
Description
Tray driver side bumper outboard with slats 15x13x10 for 66 feet of 1 3/4" double jacket hose. For use when there is an outboard option on the same side.
Tray driver side bumper outboard with slats 15x13x12 for 80 feet of 1 3/4" double jacket hose. For use when there is an outboard option on the same side.
Tray driver side bumper outboard with slats 15x13x14 for 95 feet of 1 3/4" double jacket hose. For use when there is an outboard option on the same side.
Tray officer side bumper outboard with slats 17x9x10 for 51 feet of 1 3/4" double jacket hose. This tray is for use when the tow eyes are mounted in the up position.
Tray officer side bumper outboard with slats 17x9x12 for 63 feet of 1 3/4" double jacket hose. This tray is for use when the tow eyes are mounted in the up position.
Tray officer side bumper outboard with slats 17x9x14 for 74 feet of 1 3/4" double jacket hose. This tray is for use when the tow eyes are mounted in the up position.
Tray officer side bumper outboard with slats 15x13x10 for 66 feet of 1 3/4" double jacket hose. For use when there is an outboard option on the same side.
Tray officer side bumper outboard with slats 15x13x12 for 80 feet of 1 3/4" double jacket hose. For use when there is an outboard option on the same side.
Tray officer side bumper outboard with slats 15x13x14 for 95 feet of 1 3/4" double jacket hose. For use when there is an outboard option on the same side.
Tray center of bumper with slats 34x17x10 for 195 feet of 1 3/4" double jacket hose or 75 feet of 5" LDH
Tray center of bumper with slats 34x17x12 for 239 feet of 1 3/4" double jacket hose or 91 feet of 5" LDH
Tray center of bumper with slats 34x17x14 for 282 feet of 1 3/4" double jacket hose or 108 feet of 5" LDH
Tray center of bumper with slats 34x17x10 with divider running front to back
Tray center of bumper with slats 34x17x12 with divider running front to back
Tray center of bumper with slats 34x17x14 with divider running front to back
Tray center of bumper with slats 34x17x10 with divider running side to side
Tray center of bumper with slats 34x17x12 with divider running side to side
Tray center of bumper with slats 34x17x14 with divider running side to side
Tray driver side bumper outboard with slats 17x13x10 for 74 feet of 1 3/4" double jacket hose. For use when the tow eyes are mounted in the up position.
Tray driver side bumper outboard with slats 17x13x12 for 91 feet of 1 3/4" double jacket hose. For use when the tow eyes are mounted in the up position.
Tray driver side bumper outboard with slats 17x13x14 for 108 feet of 1 3/4" double jacket hose. For use when the tow eyes are mounted in the up position.
Tray driver side bumper outboard with slats 15x17x10 for 86 feet of 1 3/4" double jacket hose. For use when there is an outboard option on the same side.
Tray driver side bumper outboard with slats 15x17x12 for 105 feet of 1 3/4" double jacket hose. For use when there is an outboard option on the same side.
PRICE
$674.00
$674.00
$674.00
$674.00
$674.00
$674.00
$674.00
$674.00
$674.00
$737.00
$737.00
$737.00
$737.00
$737.00
$737.00
$737.00
$737.00
$737.00
$674.00
$674.00
$674.00
$674.00
$674.00
Option No.
1150‐0053
1150‐0054
1150‐0055
1150‐0056
1150‐0059
1150‐0060
1150‐0061
1150‐0062
1150‐0063
1150‐0064
1150‐0065
1150‐0069
1150‐0070
1150‐0071
1150‐0072
1150‐0074
1150‐0075
1150‐0085
1150‐0086
1150‐0087
1150‐0088
1150‐0089
1150‐0090
1150‐0091
1150‐0092
1150‐0093
1150‐0094
1150‐0095
1150‐0096
Description
Tray driver side bumper outboard with slats 15x17x14 for 124 feet of 1 3/4" double jacket hose. For use when there is an outboard option on the same side.
Hinged diamond plate lid for driver side bumper tray. Includes 1/4 turn latch and gas shock hold open.
Hinged diamond plate lid for center bumper tray. Includes 1/4 turn latch and gas shock hold open.
Hinged diamond plate lid for officer side bumper tray. Includes 1/4 turn latch and gas shock hold open.
Red vinyl lid with velcro fasteners for bumper tray driver side.
Red vinyl lid with velcro fasteners for bumper tray officer side.
Red vinyl lid with velcro fasteners for bumper tray center.
Black vinyl lid with velcro fasteners for bumper tray driver side.
Black vinyl lid with velcro fasteners for bumper tray officer side.
Black vinyl lid with velcro fasteners for bumper tray center.
Diamond plate lid for driver, center, and officer hose trays. 5.25" high with dual chrome grab handles, rubber hood latches and gas shocks.
Tray officer side bumper outboard with slats 17x13x10 for 74 feet of 1 3/4" double jacket hose. For use when the tow eyes are mounted in the up position.
Tray officer side bumper outboard with slats 17x13x12 for 91 feet of 1 3/4" double jacket hose. For use when the tow eyes are mounted in the up position.
Tray officer side bumper outboard with slats 17x13x14 for 108 feet of 1 3/4" double jacket hose. For use when the tow eyes are mounted in the up position.
Tray officer side bumper outboard with slats 15x17x10 for 86 feet of 1 3/4" double jacket hose. For use when there is an outboard option on the same side.
Tray officer side bumper outboard with slats 15x17x12 for 105 feet of 1 3/4" double jacket hose. For use when there is an outboard option on the same side.
Tray officer side bumper outboard with slats 15x17x14 for 124 feet of 1 3/4" double jacket hose. For use when there is an outboard option on the same side.
Nylon black strap on officer side front bumper tray (EA).
Nylon black strap on driver side front bumper tray (EA).
Nylon black strap on center front bumper tray (EA).
Tray officer side bumper outboard with slats 23x18x14 for 202 feet of 1 3/4" double jacket hose
Tray driver side bumper outboard with slats 23x18x14 for 202 feet of 1 3/4" double jacket hose
Tray center of bumper with slats 20x18x14 for 176 feet of 1 3/4" double jacket hose or 67 feet of 5" LDH.
Tray officer side bumper outboard with slats 23x14x14 for 157 feet of 1 3/4" double jacket hose.
Tray driver side bumper outboard with slats 23x14x14 for 157 feet of 1 3/4" double jacket hose.
Tray center of bumper with slats 20x14x16 for 136 feet of 1 3/4" double jacket hose or 52 feet of 5" LDH
Hinged diamond plate lid for driver side bumper tray. Includes D‐Ring latch and gas shock hold open.
Hinged diamond plate lid for center bumper tray. Includes D‐Ring latch and gas shock hold open.
Hinged diamond plate for officer side bumper tray. Includes D‐Ring latch and gas shock hold open.
PRICE
$674.00
$294.00
$324.00
$294.00
$193.00
$193.00
$193.00
$193.00
$193.00
$193.00
$633.00
$674.00
$674.00
$674.00
$674.00
$674.00
$674.00
$84.00
$84.00
$84.00
$737.00
$737.00
$674.00
$737.00
$737.00
$674.00
$322.00
$352.00
$322.00
Option No.
1150‐0097
1150‐0098
1150‐0100
1150‐0102
1150‐0103
1150‐0104
1150‐0105
1150‐0106
1150‐0107
1150‐0108
1150‐0109
1150‐0110
1150‐0111
1150‐0112
1150‐0113
1150‐0114
1150‐0115
1150‐0116
1150‐0117
1150‐0118
1150‐0119
1150‐0120
1150‐0121
1150‐0122
1150‐0123
1150‐0124
1150‐0125
1150‐0126
Description
Tray driver side bumper outboard for hydraulic/cord reel.
Tray officer side bumper outboard for hydraulic/cord reel.
Hinged floor of center bumper tray. Hinged to the rear.
Diamond plate lid for driver hosetray. 5.25" high with chrome grab handle, rubber hood latch, gas shock and water stop angle.
Diamond plate lid for center hose tray 5.25" high with chrome grab handle, rubber hood latch, gas shock and water stop angle.
Diamond plate lid for officer hosetray. 5.25" high with chrome grab handle, rubber hood latch, gas shock and water stop angle.
Diamond plate lid for center and driver hosetrays; 2/3 lid. 5.25" high with chrome grab handle, rubber hood latches, gas shocks and water stop angle.
Diamond plate lid for center and officer hosetrays; 2/3 lid. 5.25" high with chrome grab handle, rubber hood latches, gas shocks and water stop angle.
Nylon black strap with clip release on officer side front bumper tray.
Nylon black strap with clip release on driver side front bumper tray.
Nylon black strap with clip release on center front bumper tray. The strap shall be attached to the inboard side of the tray and shall not reduce the overall tray capacity
(3) bumper extension trays. (1) officer side inboard of front intake. Tray is for storage of 25' of 5" LDH rolled hose (not flat lay). (1) tray center for storage of hydraulic tool. Tray not to be deeper than bumper extension. (1) tray driver side for storage of a Hannay hydraulic reel. The reel is for "core" technology (size larger than standard). The center and driver tray to be under (1) hinged raised lid with gas shock hold‐open. Lid to include (2) LED lights‐ (1) over the reel and (1) over the tool storage area. Lights to be switched with parking brake and headlamps.
Additional divider for front bumper hose tray.
Hinged diamond plate lid for center bumper tray. Includes D‐Ring latch and moon spring hold open.
Tray center of bumper with slats 34x11x14 for 150 feet of 1 3/4" double jacket hose for use with center bumper speaker option
Access cover in center bumper tray for center bumper mounted speaker.
Notch bumper tray lid for preconnected hose. Notch location: [#LOC].
Bumper tray driver's side with slats 10 inches deep (approx 9 inches to slats).
Bumper tray driver's side with slats 12 inches deep (approx 11 inches to slats).
Bumper tray driver's side with slats 14 inches deep (approx 13 inches to slats).
Bumper tray center of bumper with slats 10 inches deep (approx 9 inches to slats).
Bumper tray center of bumper with slats 12 inches deep (approx 11 inches to slats).
Bumper tray center of bumper with slats 14 inches deep (approx 13 inches to slats).
Bumper tray officer's side with slats 10 inches deep (approx 9 inches to slats).
Bumper tray officer's side with slats 12 inches deep (approx 11 inches to slats).
Bumper tray officer's side with slats 14 inches deep (approx 13 inches to slats).
Divider center bumper hose tray running front to back with adjustable track (Provides two storage areas, one left and one right of divider).
Divider center bumper hose tray running side to side with adjustable track (Provides two storage areas, one ahead and one behind divider).
PRICE
$737.00
$737.00
$814.00
$417.00
$417.00
$417.00
$525.00
$525.00
$149.00
$149.00
$149.00
$2,422.00
$112.00
$352.00
$737.00
$100.00
$146.00
$486.00
$486.00
$486.00
$486.00
$486.00
$486.00
$486.00
$486.00
$486.00
$255.00
$255.00
Option No.
1150‐0127
1150‐0128
1150‐0129
1150‐0130
1150‐0131
1150‐0132
1150‐0133
1150‐0135
1150‐0136
1150‐0137
1150‐0138
1150‐0139
1150‐0140
1150‐0141
1150‐0142
1150‐0143
1150‐0144
1150‐0145
1150‐0146
1150‐0147
1150‐0148
1150‐0149
1150‐0150
1150‐0151
1150‐0152
1150‐0153
1150‐0154
Description
Tray center of bumper with slats 34x13x16 with divider running side to side
Notch front bumper tray for speaker/Q2B/radar. Will reduce front hose/equipment load. Center tray only.
Diamond plate lid for center hosetray. Includes chrome grab handle, rubber hood latches and gas shock.
Black nylon cargo net on center front bumper tray.
Extinguisher tube in front bumper extension. Location: [#LOC].
Tray center bumper for hydraulic/cord reel.
Diamond plate raised full lid for extended front bumper. 6" high with dual chrome grab hands, rubber hood latches and gas shocks.
Royal Blue vinyl lid with velcro fasteners for center bumper tray.
Bumper tray center of bumper with slats 16 inches deep (approx 15 inches to slats). Mount tray 1" above gravel shield.
Diamond plate lid for center hosetray and jumpline next to tray. 5.25" high with chrome grab handle, rubber hood latch, gas shock and water stop angle if applicable.
Bumper pan driver's side without slats 4 inches deep with strap. For use with suction strainer only.
Nylon black strap with aluminum quick release buckle for front bumper hose tray. Strap to attach to front and rear walls of tray down low as applicable. Location: [#LOC].
Bumper tray center of bumper with slats 14 inches deep (approx 13 inches to slats). Mount tray 1" above gravel shield.
Bumper tray officer's side with slats 12 inches deep (approx 11 inches to slats). Mount tray 1" above gravel shield.
Hinged diamond plate lid for center bumper tray. Includes (4) sides, 1/4 turn latch and gas shock hold open. For use with raised compts only.
Hinged diamond plate lid for officer bumper tray. Includes (4) sides, 1/4 turn latch and gas shock hold open. For use with raised compts only.
Diamond plate lid for center hosetray and jumpline next to tray. 8.25" high with chrome grab handle, rubber hood latch, gas shock and water stop angle if applicable.
Single crosslay on top of the front bumper gravel shield. Tray to be "U" shape, 10" wide x 8" high x the width of the gravel shield. Vinyl cover, [#COL], with end flaps to cover crosslay, velcro along front edge, fastened along back. Requires 24" extension.
Water stop angle. Gravel shield mounted. Requires raised lid and/or 28" bumper extension with reel trays.
Diamond plate lid for driver, center, and officer hose trays. 5.25" high with dual chrome grab handles, SS butterfly latches and gas shocks.
Tray center of bumper aft of winch max available depth as applicable.
Nylon black cargo net on sides for bumper crosslay.
Double crosslay on top of the front bumper gravel shield. Tray to be "U" shape, approx 20" wide x 7.5" high x 90" wide minimum or as per application bumper width. Holds 200' of 1.75" DJ (each). Includes tri‐fold diamond plate cover hinged at the front. Requires seperate side cover option and 28" extension.
Booster Reel Roller Assembly. Locate in front of center bumper tray.
Hinged diamond plate lid for officer side bumper tray. Includes D‐Ring latch and gas shock hold open.
Bumper tray officer's side with slats located between front intake and frame extension. Tray to be approx 9" W (min) x full length x 14" D (13" to slats) to hold 25' of 5" LDH. Requires minimum 20" extension.
Bumper tray center of bumper with slats located to rear of Q2B. Tray to be approx 34"W x 9"L x 10" deep (9" to slats).
PRICE
$737.00
$131.00
$417.00
$318.00
$818.00
$804.00
$633.00
$193.00
$580.00
$480.00
$486.00
$122.00
$580.00
$580.00
$416.00
$416.00
$544.00
$892.00
$208.00
$719.00
$486.00
$235.00
$1,529.00
$372.00
$322.00
$486.00
$705.00
Option No.
1150‐0155
1150‐0156
1150‐0157
1150‐0158
1150‐0159
1150‐0160
1150‐0161
1150‐0162
1150‐0163
1150‐0164
1150‐0165
1150‐0166
1150‐0167
1150‐0168
1150‐0169
1150‐0170
1150‐0171
1150‐0172
1150‐0173
1150‐0174
1150‐0175
1150‐0176
1150‐0177
1150‐0178
1150‐0179
1150‐0180
1150‐0181
1150‐0182
1150‐0183
1150‐0184
1150‐0185
Description
Tray officer side bumper outboard for hydraulic/cord reel.
Tray driver side bumper outboard for hydraulic/cord reel.
Diamond plate raised full lid for extended front bumper. 6" high with dual chrome grab hands, rubber hood latches and gas shocks.
Bumper tray center of bumper without slats 12 inches deep.
Bumper tray center of bumper with slats 16 inches deep (approx 15 inches to slats).
Hinged smooth plate lid for center bumper tray. Includes D‐Ring latch and gas shock hold open. Smooth plate lid will be painted with black Durabak.
Double crosslay on top of the front bumper gravel shield. Tray to be "U" shape to hold 200' of 1.75" DJ (each). Includes bi‐fold diamond plate cover hinged at the rear. Requires separate side cover option and 28" extension.
Surface mounted tray center of bumper extension. Tray to be sized to fit between outboard reel trays and includes a 1" lip all the way around. Tray is for mounting of customer supplied hydraulic tools that will be utilized with reel applications.
Tray officer side bumper next to front intake/discharge. Half moon style for 25' of 5'' rolled hose.
Bumper tray center of bumper with black Turtle Tile 14" deep (approx. 13.25" from tile). Includes: hinged diamond plate lid for center bumper tray with Tri‐Mark latch, gas shock hold open and door ajar switch.
Bumper tray driver's side without slats 10 inches deep.
Bumper tray driver's side without slats 12 inches deep.
Bumper tray driver's side without slats 14 inches deep.
Bumper tray center of bumper without slats 10 inches deep.
Bumper tray center of bumper without slats 12 inches deep.
Bumper tray center of bumper without slats 14 inches deep.
Bumper tray officer's side without slats 10 inches deep.
Bumper tray officer's side without slats 12 inches deep.
Bumper tray officer's side without slats 14 inches deep.
Slatted Duradek flooring in driver side bumper tray.
Slatted Duradek flooring in center bumper tray.
Slatted Duradek flooring in officer side bumper tray.
Notch front bumper tray for speaker/Q2B. Will reduce front hose/equipment load. Driver's side only.
Hinged diamond plate lid for center bumper tray. Includes push button latch and gas shock hold open.
Bumper tray center of bumper without slats 16 inches deep.
Yellow vinyl lid with velcro fasteners for bumper tray center.
Nylon black strap with aluminum quick release buckle for front bumper hose tray. Strap to attach to side walls of tray down low as applicable. Location: [#LOC].
Tray center and offset to driver side frame rail for hydraulic/cord reel.
Surface mounted tray officer side of bumper extension. Tray to be sized to fit between center reel tray and includes a 1" lip all the way around. Tray is for mounting of customer supplied hydraulic tools that will be utilized with reel applications.
Vinyl [#COL] side covers for diamond plate bumper crosslay cover.
Hinged diamond plate lid for center bumper tray. Includes push button latch and moon spring hold open.
PRICE
$783.00
$783.00
$755.00
$331.00
$486.00
$409.00
$1,529.00
$737.00
$701.00
$1,003.00
$416.00
$416.00
$416.00
$416.00
$416.00
$416.00
$416.00
$416.00
$416.00
$63.00
$63.00
$63.00
$131.00
$324.00
$416.00
$193.00
$122.00
$737.00
$362.00
$199.00
$324.00
Option No.
1150‐0186
1150‐0187
1150‐0188
1150‐0189
1150‐0190
1150‐0191
1150‐0192
1150‐0193
1150‐0194
1150‐0195
1150‐0196
1150‐0197
1150‐0198
1150‐0199
1150‐0200
1150‐0201
1150‐0202
1150‐0203
1150‐0204
1150‐0205
1150‐0206
1150‐0207
1150‐0208
1150‐0209
1150‐0210
1150‐0211
1150‐0212
1150‐0213
Description
The center front bumper tray gas shock is to be mounted to the lid from the officer side of the tray.
Nylon yellow strap with aluminium quick release buckle for front bumper hose tray. Strap to attach to front and rear walls of tray down low as applicable. Location: [#LOC].
Front bumper stainless steel hose wells, Duradek, w/hose retaining straps, Wildland
Front bumper stainless steel hose wells, Duradek, ADT hinged covers, Wildland
Front bumper stainless steel hose well lowered extensions, Wildland
Center Front bumper stainless steel well, SS floor, ADT hinged cover, Wildland
Center front bumper stainless steel well, ADT hinged cover, Used w/Winch Option, Wildland
Bumper tray center of bumper with black turtle tile 16 inches deep (approx 15 inches to tiles).
Dri‐Deck will be added to the center bumper tray. Color will be black.
Bumper tray center of bumper with black Turtle Tile 14" deep (approx. 13.25" from tile).
Tray officer side bumper next to front intake. Half moon style for 20' of 6" rolled hose.
Nylon black strap with aluminum quick release buckle. Location: driver, officer and center top of front bumper gravel shield.
Notch front bumper tray for speaker/Q2B. Will reduce front hose/equipment load. Officer's side only.
Nylon black cargo net with bungee hold downs on sides for bumper crosslay.
Bumper tray center of bumper with slats 18 inches deep (approx 17 inches to slats).
Notch front bumper tray for speaker/Q2B. Notch to be sized as close to obstacle as possible to provide more storage space in tray. Will reduce front hose/equipment load. Center only.
Bumper tray center of bumper with slats 12 inches deep (approx 11 inches to slats). The bumper tray shall be raised 2" above the gravel shield (12" total depth). The bumper tray shall be approximately 17" front to rear X 30" in length side to side. A divider shall be centered (spanning from front to back) making a left hand and right hand center bumper tray.
Hinged smooth plate lid for center bumper tray. Includes D‐Ring latch and gas shock hold open. Smooth plate lid will be painted with black Scorpion coating.
Stainless steel roller assemblies for bumper crosslays. Includes side rollers only; no bottom. Replaces stainless scuff plates on bumper crosslays.
Recessed bumper crosslay. Includes raised lid with outboard fixed panels for optional equipment. Requires 20" extension and side covers.
Hinged diamond plate lid for center bumper tray. Includes push button latch chrome grab handle and gas shock hold open.
Hinged diamond plate lid for center bumper tray. Includes 1/4 turn latch and moon spring hold open.
Bumper tray officer's side without slats, approximately 14 inches deep, 17" front to rear X 9" in length side to side.
Bumper tray driver's side without slats, approximately 14 inches deep, 17" front to rear X 17" in length side to side.
Tray driver side bumper next to frame. Half moon style for 25' of 5'' rolled hose.
Bumper tray center of bumper with slats 16 inches deep (approx 15 inches to slats). Mount tray 1" above gravel shield. Forward bottom edge has 45 degree cut to improve approach angle. Forward cut height begins at approximate tray depth as it aligns with bumper bottom, continuing rearward at a 45 degree angle.
Nylon black strap with clip release on officer side front bumper tray running front to back.
Bumper tray center of bumper (w/o slats) 10 inches deep.
PRICE
$0.00
$122.00
$1,899.00
$2,231.00
$1,000.00
$762.00
$482.00
$486.00
$89.00
$486.00
$701.00
$362.00
$131.00
$291.00
$486.00
$131.00
$486.00
$409.00
$308.00
$3,661.00
$375.00
$324.00
$486.00
$486.00
$701.00
$696.00
$149.00
$486.00
Option No.
1150‐0214
1150‐0215
1150‐0216
1150‐0217
1150‐0218
1150‐0219
1150‐0220
1150‐0221
1150‐0222
1150‐0223
1150‐0224
1150‐0225
1150‐0226
1150‐0227
1150‐0228
1150‐0230
1150‐0231
1150‐0232
1150‐0233
1150‐0234
1150‐0235
1150‐0236
1150‐0237
1150‐0238
Description
Traffic cone storage on front bumper extension. Cones to be oriented downard through a 7 3/4" hole in the gravelshield. Includes nylon strap with aluminum buckle. Location: [#LOC].
Hinged diamond plate lid for center bumper tray. Includes 1/4 turn latch and two (2) gas shock hold open.
Bumper tray lid(s) to be constucted using 3/16" aluminum ipos.
Hinged diamond plate lid for officer side bumper tray 2/3 of length hinged 1/3 remaining length is fastened in place. Hinged inboard,/fixed portion outboard. Includes D‐Ring latch and gas shock to hold open the hinged section.
Bumper tray center of bumper with slats 12 inches deep (approx 11 inches to slats). Mount tray 1" above gravel shield.
Additional gas shock on front bumper tray lid. Location: [#LOC].
Tray driver side bumper outboard for hydraulic/cord reel, 18 inches deep IPOS.
Tray officer side bumper outboard for hydraulic/cord reel, 18 inches deep IPOS.
The gravel shield lid shall open 90 degree's. The gas shock(s) shall be at a length and placed to allow the door to open a full 90 degrees.
Bumper tray officer's side with slats 16 inches deep (approx 15 inches to slats).
Bumper tray officer's side without slats located between front intake and frame extension. Tray to be approx 9" W (min) x full length x 14" D (13" to slats) to hold 25' of 5" LDH. Requires minimum 20" extension.
The rear wall of bumper tray to have louvers for additional ventilation. Location: [#LOC].
Smooth plate raised full lid with black Durabak finish for extended front bumper. 6" high with dual chrome grab hands, rubber hood latches and gas shocks.
Bumper tray center of bumper with slats 18 inches deep (approx 17 inches to slats).
Bumper tray driver's side of bumper with black Turtle Tile 14" deep (approx. 13.25" from tile).
Bumper trough full length, mounted on top of gravel shield. Trough shall run side to side 4" high, 7" wide made from 3/16" smooth plate aluminum.
Nylon black strap with aluminum quick release buckle for front bumper hose tray. Strap to attach to front and rear walls of tray as high as possible. Location: [#LOC].
Hinged diamond plate lid for center bumper tray. Includes Tri‐Mark latch and gas shock hold open.
Hinged smooth plate lid for driver side bumper tray. Includes D‐Ring latch and gas shock hold open. Lid to painted with black Scorpion brand coating inside and outside surfaces (smooth finish).
Bumper tray driver's side with slats 10 inches deep (approx 9 inches to slats). Tray interior to be painted with black Scorpion coating (smooth finish), Slat assembly to remain unpainted aluminum.
Diamond plate lid 3/16 " thick for driver, center, and officer hose trays. 5.25" high with dual chrome grab handles, SS butterfly latches and gas shocks.
Recessed bumper double crosslay to hold of 200' of 1.75" DJ hose in each crosslay. The crosslay floor/bottom shall be slotted to allow drainage (no slats). Includes hinged bi‐fold raised lid in center with outboard fixed panels for optional equipment and stainless steel scuff guards at each side of crosslay opening across bottom and sides. Requires 28" extension, side covers, 12" heavy duty bumper and engineering approval.
Bumper tray driver's side without slats. Tray to be approx 17.5" W x 17"L x 14" D.
Bumper tray officer's side without slats. Tray to be approx 11" W x 17"L x 14" D.
PRICE
$402.00
$354.00
$155.00
$322.00
$580.00
$167.00
$898.00
$898.00
$0.00
$486.00
$416.00
$190.00
$1,553.00
$416.00
$486.00
$260.00
$122.00
$433.00
$428.00
$594.00
$782.00
$3,960.00
$416.00
$416.00
Option No.
1150‐0239
1150‐0240
1150‐0241
1150‐0242
1150‐0243
1150‐0244
1150‐0245
1150‐0246
1150‐0247
1150‐0248
1150‐0249
1150‐0250
1150‐0252
1150‐0253
1150‐0254
1150‐0255
1150‐0256
1150‐0257
1150‐0258
Description
Bumper trays shall have 1/2" drain holes IPOS.
Recessed bumper tray centered full width 6.25" deep. Includes 5.25" raised lid centered. The gravel shield outboard of lid shall serve for mounting of optional equipment. Requires 20" extension and engineering approval.
Bumper tray center of bumper with slats 14 inches deep (approx 13 inches to slats) fabricated from smooth plate aluminum. Outside facing surface of tray below bumper shall be painted black Durabak.
Black nylon cargo net on officer side front bumper tray.
Bumper tray officer's side with slats 10 inches deep (approx 9 inches to slats). Mount tray 2" above gravel shield.
Bumper tray cover(s) to be dealer/customer provided and installed. Cove(s) to meet current NFPA standard(s) to prevent un‐intentional deployment of hose.
Bumper tray driver's side with slats 10 inches deep (approx 9 inches to slats). Mount tray 2" above gravel shield.
Bumper tray center of bumper with Duradek 16 inches deep.
Hinged diamond plate lid raised 3" high for center bumper tray. Includes a single chrome grab handle, SS butterfly latches and gas shocks.
Divider driver side bumper hose tray running side to side with adjustable track (Provides two storage areas, one ahead and one behind divider).
Divider officer side bumper hose tray running side to side with adjustable track (Provides two storage areas, one ahead and one behind divider).
Single crosslay on top of the front bumper gravel shield. Tray to be "U" shape, approx 10" wide x 7.5" high x 90" wide. Holds 200' of 1.75" DJ (each). Includes diamond plate cover hinged at the front. Requires seperate side cover, and 24" extension.
Recessed bumper double crosslay. Includes 5.25" full width raised lid. The crosslay shall only be accessible through the top lid (no side access). The crosslay floor/bottom shall be slotted to allow drainage (no slats). The crosslay shall include an adjustable divider going from side to side to create a forward and rear crosslay run area. Requires 28" extension and engineering approval.
Black nylon cargo net on driver side front bumper tray.
Bumper tray driver side of bumper with slats 14 inches deep (approx 13 inches to slats) fabricated from smooth plate aluminum. Mount tray 2" above gravel shield. Outside facing surface of tray below bumper shall be painted black Durabak.
Hinged smooth plate lid for driver side bumper tray. Includes D‐Ring latch and gas shock hold open. Smooth plate lid will be painted with black Durabak.
Bumper tray(s) to be constructed using smooth plate aluminum with exterior surface painted black Durabak.
Recessed bumper double crosslay to hold of 200' of 1.75" DJ hose with pistol grip (raise lid an additional 1") in each crosslay. The crosslay floor/bottom shall be slotted to allow drainage (no slats). Includes hinged bi‐fold raised lid in center with outboard fixed panels for optional equipment and polished stainless steel scuff guards at each side of crosslay opening across bottom and sides. Requires 28" extension, side covers, 12" heavy duty bumper and engineering approval.
Recessed bumper double crosslay to hold of 200' of 1.75" DJ hose in each crosslay. The crosslay floor/bottom shall be slotted to allow drainage (no slats). Includes hinged bi‐fold raised lid in center with outboard fixed panels for optional equipment and stainless steel rollers at each side of crosslay opening across bottom and sides. Requires 28" extension, side covers, 12" heavy duty bumper and engineering approval.
PRICE
$29.00
$3,881.00
$581.00
$318.00
$580.00
$0.00
$580.00
$530.00
$395.00
$255.00
$255.00
$1,198.00
$4,529.00
$318.00
$677.00
$409.00
$194.00
$3,960.00
$4,119.00
Option No.
1150‐0259
1150‐0260
1150‐0261
1150‐0262
1150‐0263
1150‐0264
1150‐0265
1150‐0266
1150‐0267
1150‐0268
1150‐0269
1150‐0270
1150‐0271
1150‐0272
1150‐0273
1150‐0274
1150‐0275
1150‐0276
1150‐0277
Description
.Bumper tray with no slats approx. 6" deep extending full width of the bumper as applicable based on outboard options. Includes notched frame extensions to provide flat floor for the tray.
Recessed bumper double crosslay to hold of 200' of 1.75" DJ hose in each crosslay. The crosslay floor/bottom shall be slotted to allow drainage (no slats). Includes full width hinged bi‐fold raised lid and stainless steel scuff guards at each side of crosslay opening across bottom and sides. Requires 28" extension, side covers, 12" heavy duty bumper and engineering approval.
Diamond plate lid for driver, center, and officer hose trays. approx 6.25" high or as applicable to allow for jumpline swivel to be under lid pre‐connected. with dual chrome grab handles, SS butterfly latches and gas shocks.
Vinyl cover for bumper tray notch. Includes diamond plate over perimeter of cover.
Recessed bumper crosslay to hold of 150' of 1.75" DJ hose. The crosslay floor/bottom shall be slotted to allow drainage (no slats). Includes full width flat lid. Requires 20" extension, side covers and 10" heavy duty bumper.
Recessed bumper double crosslay to hold 200' of 1.75" DJ hose in each crosslay with a nozzle as applicable. The crosslay floor/bottom shall be slotted to allow drainage (no slats). Includes hinged bi‐fold full width raised lid for open full access to crosslays when open and stainless steel scuff guards at each side of crosslay opening across bottom and sides. Requires 28" extension, side covers, 12" heavy duty bumper and engineering approval. Lid shall be raised approx 5.25" above top of bumper for capacity to ensure ease of use with a nozzle. Lid to be secured in closed position with S/S Butterfly latches. Capacity may be affected and may require a compact nozzle depending on hose selection as loaded.
One continuous recessed bumper tray extending over the center and driver side of the bumper shall be provided with a raised 5.25" lid centered side to side.
Smooth plate raised full lid with black Durabak finish for extended front bumper. 6" high with one 24" Haralson Metals Stainless knurled handrail in place of grab handles centered on the lid, butterfly latches on side and gas shocks.
Bumper tray center / driver side of bumper w/o slats 12 inches deep. Tray to extend to driver side over frame extension. Officer side of tray to be approx 11" towards officer side from center. Tray to be 12" deep each side of step over frame. Requires drop frame extension option.
Bumper tray officer side / center of bumper with slats 12 inches deep (approx 11 inches to slats). Tray to extend to center area over frame extension. Inboard side of tray to be approx 14" towards officer side from center. Requires drop frame extension option.
Bumper tray to be constucted using 3/16" aluminum ipos.
Tray officer side bumper next to frame. Half moon style for (3) 50' sections of 1.5'' rolled hose.
Tray driver side bumper next to frame. Half moon style for (6) 50' sections of 1'' rolled hose.
Raised lid over bumper tray to be extended over jumpline swivel on top of gravel shield. For use with 2" swivel only.
Nylon black cargo net with black powder coated quick release buckles on sides for bumper crosslay.
Stainless steel roller assemblies for bumper crosslays. Includes side rollers and bottom. Replaces stainless scuff plates on bumper crosslays.
Hinged smooth plate lid for center bumper tray. Includes 1/4 turn latch and gas shock hold open. Smooth plate lid will be painted black Durabak.
Nylon black strap with aluminum quick‐release buckle. Location: driver, officer and (2) center top of front bumper gravel shield.
Red vinyl lid with snap fasteners for bumper tray officer side.
PRICE
$905.00
$4,388.00
$762.00
$268.00
$3,661.00
$4,174.00
$3,881.00
$1,606.00
$526.00
$669.00
$108.00
$701.00
$701.00
$63.00
$342.00
$320.00
$404.00
$486.00
$1,366.00
Option No.
1150‐0278
1150‐0279
1150‐0280
1150‐0281
1150‐0282
1150‐0283
1150‐0284
1150‐0286
1150‐0287
1150‐0288
1150‐0289
1150‐0290
1150‐0291
1150‐0292
1150‐0293
1150‐0294
1150‐0295
1150‐0296
1150‐0297
1150‐0298
1150‐0299
1150‐0300
1150‐0301
Description
Bumper tray officer's side with slats to hold (2) lengths of 3" DJ hose, approximately 18" W X 14" L X 15" D
Tray center of bumper forward of winch max depth as applicable per winch application. Smooth plate .125 aluminum DA finish. Tray will will be forward of winch mount and access lid above fairlead path. Recessed to max allowable depth per application to provide additional storage depth under raised lid for rescue tool to be placed topside under lid.
Bumper tray center of bumper with slats 17 inches deep (approx 16 inches to slats). Mount tray 1" above gravel shield. Exterior of tray to be painted FLNA4145 Black.
Hinged diamond plate lid for driver side bumper tray. Includes D‐Ring latch and moon spring hold open.
Hinged diamond plate lid for center bumper tray. Includes Southco model C2‐32‐11‐3 push button latch and gas shock hold open.
Hinged diamond plate lid for center and officer bumper tray. Includes (2) D‐Ring latches, (2) gas shock hold open and smooth plate spacer between bumper trays.
Nylon black strap with aluminum quick release buckle. Location: driver, officer and center top of front bumper gravel shield. Mount at final inspection.
Shallow bumper tray located center of the bumper without slats. Tray to be as wide and as deep as possible while maintaining a flat floor without notches or protrusions.
Hinged diamond plate lid for officer side bumper tray. Includes D‐Ring latch and moon spring hold open.
Bumper tray, secondary. Tray located towards the rear beneath first center tray for additional storage. Tray to be as long front to back as possible while maintaining a flat floor without notches or protrusions and still have the seconday lid removable. Tray to be as wide as applicable and as deep as other trays on the truck.
Diamond plate lid for driver, center, and officer hose trays. 5.25" high with dual chrome grab handles, SS butterfly latches and gas shocks. Hinge will be located as low down and far back as possible on fixed portion of the lid.
All fabricated aluminum sheet metal parts installed on the bumper shall be made using smooth plate in place of standard. Includes gravel shield, tray(s), lid(s) and other miscellanous parts.
Crosslay divider(s) to be held back 6" from each side of bumper.
Bumper tray with no slats extending full width of the bumper as applicable based on outboard options. Includes notched frame extensions to provide at least 6" tray depth directly above the extensions. Tray to have multiple depth to meet customer specific requirements.
Bumper tray driver side of bumper made as large as possible with slats 14 inches deep (approx 13 inches to slats). Mount tray 1" above gravel shield.
Insulation on exterior of the bumper tray assembly. Location: Driver side.
Bumper lid to have one 24" knurled handrail in place of grab handles centered on the lid.
Hinged diamond plate lid for officer bumper tray. Includes Tri‐Mark latch and gas shock hold open.
Bumper tray driver side of bumper made as large as possible without slats 14 inches deep. Mount tray 1" above gravel shield.
Bumper tray center of bumper without slats 14 inches deep. Mount tray 1" above gravel shield.
Tray officer side bumper inboard of frame. Half moon style for 25' of 5'' rolled hose.
Bumper tray driver's side with slats 16 inches deep (approx 15 inches to slats).
Tray center of bumper aft of winch max available depth as applicable. Slats shall be provided.
PRICE
$509.00
$307.00
$934.00
$352.00
$324.00
$673.00
$362.00
$330.00
$352.00
$433.00
$719.00
$194.00
$0.00
$1,708.00
$688.00
$252.00
$60.00
$433.00
$688.00
$580.00
$701.00
$486.00
$586.00
Option No.
1150‐0302
1150‐0303
1150‐0304
1150‐0305
1150‐0306
1150‐0307
1150‐0308
1150‐0309
1150‐0310
1150‐0311
1150‐0312
1150‐0313
1150‐0314
1150‐0315
1150‐0316
Description
Raised diamond plate lid with dual chrome grab handles, stainless steel butterfly latches and gas shocks. The lid shall be full width (as applicable based on outboard options) and high enough to accomodate reels, rescue tools and equipment as applicable per customer specific requirements.
Nylon black strap with aluminum quick release buckle for front bumper hose tray. Strap to attach to front and rear top of tray. Location: [#LOC].
Recessed bumper double crosslay to hold 150' of 1.75" DJ hose in each crosslay. The crosslay floor/bottom shall be slotted to allow drainage (no slats). Includes hinged bi‐fold raised lid and stainless steel scuff guards at the crosslay opening across bottom and sides. Requires 28" extension, side covers, 12" heavy duty bumper and engineering approval. Crosslay only open on one side of the bumper extension.
Bumper tray full width of bumper without slats 12" deep. For use with outboard options. Tray to extend to driver/officer area over frame extension. Center of tray to be approx 12" deep with outboard areas approx. 5.5" deep. Requires drop frame extension option.
Recessed bumper double crosslay to hold of 200' of 1.75" DJ hose in each crosslay. The crosslay floor/bottom shall be slotted to allow drainage (no slats). Includes full width hinged non bi‐fold raised lid with side lips to hold up hinged drop down doors. Hinge will be southco brand hinge to keep lip held in the open position when in use. Rubber hold down latches ipo butterfly latches will be used to secure lid in closed position. Stainless steel scuff guards at each side of crosslay opening across bottom and sides, with a drop down door for side access. Requires 28" extension, side covers, 12" heavy duty bumper and engineering approval.
Bumper tray center of bumper with slats 16 inches deep (approx 15 inches to slats). Mount tray 2" above gravel shield.
Removable recessed lid for front bumper tray. Includes hand hole cutout for ease of removal to access. See drawing for specific customer location requirements. Finish: Sanded Aluminum.
Hinged smooth plate lid with DA finish for center bumper tray. Includes 1/4 turn latch and gas shock hold open.
Modify bumper crosslay. Includes lower side to side divider to 7" tall and ship loose. Add adjustable tracks on front and rear center with divider centered; installed. Single gas shock in center of lid. Outboard hold open devices (see photos on file with sales).
Hinged diamond plate lid for driver bumper tray. Includes (4) sides, 1/4 turn latch and gas shock hold open. For use with raised compts only.
Bumper tray full width of bumper (for use with outboard options) without slats approx. 6" inches deep outboard of frame rails and 12" deep center between rails. Outboard sides raised for airhorns.
Recessed bumper crosslay to hold of 200' of 1.75" DJ hose. The crosslay floor/bottom shall be slotted to allow drainage (no slats). Includes full width lid. Requires minimum 20" extension, side covers and 12" heavy duty bumper.
Bumper tray center / driver side of bumper w/o slats 12 inches deep. Tray to extend to driver side over frame extension. Tray to be 12" deep each side of step over frame. Requires drop frame extension option.
Hinged diamond plate lid for single center/driver bumper tray. Includes (2) push button latches and (2) gas shock hold opens.
D&S brand heavy duty [#COL] vinyl cover for bumper tray. Location: center bumper tray. Driver side of cover to feature a notch for 2.5" hose from bumper discharge to be pre‐connected to hose stored in hose tray.
PRICE
$719.00
$122.00
$4,388.00
$895.00
$4,888.00
$580.00
$293.00
$324.00
$803.00
$416.00
$1,163.00
$3,661.00
$526.00
$524.00
$484.00
Option No.
1150‐0317
1150‐0318
1150‐0319
1155‐0000
1155‐0001
1155‐0002
1155‐0003
1155‐0004
1155‐0005
1155‐0007
1155‐0008
1155‐0009
1155‐0010
1155‐0012
1155‐0013
1155‐0014
1155‐0016
1155‐0018
1155‐0019
1155‐0020
1155‐0021
Description
Recessed bumper double crosslay to hold of 200' of 1.75" DJ hose in each crosslay. The crosslay floor/bottom shall be slotted to allow drainage (no slats). Includes hinged bi‐fold raised lid in center with driver side outboard fixed panel for optional equipment and stainless steel scuff guards at each side of crosslay opening across bottom and sides. Requires 28" extension, side covers, 12" heavy duty bumper and engineering approval.
Bumper tray driver's side with slats 14 inches deep (approx 13 inches to slats). Tray shall be designed and built as big as possible for extra capacity.
45 degree angles horizontally mounted on bottom of front bumper tray(s) for water deflection.
Class III hitch for portable winch for the front.
Receiver under body rearward of wheel well (PR) for winch or rope use (does not include 12V power plug).
Winch, electric front mounted Ramsey 12,000 lb. Includes access door with quarter turn latch and spring hold open device.
Winch Warn Series 8 ‐ 8,000lb with 125' 3/8" plated cable.
Winch semi hidden Warn 12,000lb with 125' 3/8" plated cable. N/A with 16" extended bumper.
Winch, Warn Series 12, 12,000 lb. with 125' 3/8" plated cable. Includes access door with quarter turn latch and spring hold open device. Locate: Mounted to the chassis frame extension centered at the front bumper area.
Winch control receptacle location: [#LOC].
Winch, Warn Series 12, 12,000 lb. with 125' 3/8" plated cable. Mounted in the brush gaurd. Includes rollers.
Winch, Warn 16.5ti, tow eye, front bumper, Wildland
Warn winch model 16.5 TI with 90' of 7/16" diameter IWRC or equal high performance wire rope with a 4‐way roller cable guide controlled with a 30` remote control switch located at the rear of the rescue apparatus.
PRICE
Winch, Warn 16.5ti 16,500 lb. with 90' 7/16" plated cable. Includes access door with quarter turn latch and spring hold open device.
Winch, Warn Series 12, 12,000 lb. with 125' 3/8" plated cable. Includes access door, hinged rearward that is smooth plate alum (IPO tread) and painted with black Scorpion brand coating inside and outside surfaces (smooth finish). Latch to be D‐Ring style (IPO std. 1/4 turn latch). Lid to have 1 gas shock.
A 6000 lb Warn multi‐mount (portable) electric reversible winch with 125' of 3/8'' plated wire rope and a replaceable clevis hook shall be installed and shall be controlled with a 12' remote control switch. Includes rollers.
20,000lb Hydraulically Driven Winch. Ramsey Model H800R (Mfg.Part# 124410) Hydraulic Winch with Dow‐Lok Clutch, roller guide assembly, minimum 200' of 5/8" Wire Rope Assembly, Winch Mounting Brackets, PTO and Hydraulic Pump. Maudlin to supply and install winch, E‐One to complete installation.
Winch, Warn Series 12‐S Spydura Pro, 12,000 lb. with 100' of 7/16" synthetic rope and Hawse fairlead. Includes access door with quarter turn latch and spring hold open device.
Winch, Warn Series 12, 12,000 lb. Includes 100' 7/16" Spydura Pro synthetic rope, fairlead & 32' remote. Locate: Mounted to the chassis frame extension centered at the front bumper area. A service access to the winch shall be provided.
$6,036.00
Winch, Warn Series 15, 15,000 lb. with 90' 7/16" plated cable. Includes access door with quarter turn latch and spring hold open device.
Warn Winch 9,000 lb. with 125' 3/8" plated cable. Includes access door with quarter turn latch and spring hold open device. Locate: Mounted to the chassis frame extension centered at the front bumper area.
$3,960.00
$737.00
$500.00
$932.00
$3,478.00
$4,348.00
$3,733.00
$4,108.00
$5,468.00
$0.00
$5,340.00
$6,450.00
$6,036.00
$5,604.00
$2,388.00
$14,323.00
$6,110.00
$5,879.00
$5,846.00
$3,192.00
Option No.
1160‐0000
1160‐0001
1160‐0002
1160‐0004
1160‐0006
1160‐0007
1160‐0008
1160‐0010
1160‐0011
1160‐0012
1160‐0013
1160‐0014
1160‐0015
1160‐0016
1160‐0020
1160‐0021
1160‐0022
1160‐0026
1160‐0030
1160‐0031
1160‐0032
1160‐0034
1160‐0041
1160‐0042
1160‐0043
1160‐0046
1160‐0047
1160‐0049
1160‐0050
1160‐0051
1160‐0052
1160‐0053
1160‐0054
1160‐0055
Description
Bumper 10" stainless steel.
Bumper 12" high swept back stainless steel.
Bumper reinforcement backing. For use with 10" SS or heavy duty bumpers only.
Stainless Steel 10" high front bumper. Requires extended front bumper.
Brush Guard for Akron Auto Bumper Turret
Brush guard for Akron StreamMaster bumper turret.
3/16" Front Bumper Gravel Shield.
1/8" Front Bumper Gravel Shield.
4" Front Bumper Extension.
12" Front Bumper Gravel Shield Extension.
16" Front Bumper Gravel Shield Extension.
20" Front Bumper Gravel Shield Extension.
24" Front Bumper Gravel Shield Extension.
28" Front Bumper Gravel Shield Extension.
License plate holder mounted center of front bumper.
Number plate, removable size to fit between air horns on front bumper. Spaced out from face of bumper so plate can be removed.
Brush guard for Rhino bumper turret.
Brush Guard Stainless Steel Ford F550
Steel tow bar located below front bumper mounted to chassis extensions for towing purposes only, painted black.
Notch front bumper for low "S" type front intake. Includes tray below pipe extending from cab to bumper.
1/8" diamond plate gravel shield. For use with Spartan extended front bumper.
8" Front Bumper Extension.
Heavy duty front bumper 10" high with full wrap around. To be painted job color.
Heavy duty front bumper 10" high with full wrap around. To be painted 767681 EG black.
Brush guard for Akron Fire Fox bumper turret.
10" Stainless steel front bumper with driver side cut‐out for MS‐100‐01 speaker. Includes 20" bumper extension with center‐mounted hose storage tray with lid.
10" Stainless Steel front Bumper with 20" Bumper extension and center‐mounted hose storage tray with Lid. International
License plate holder mounted officer side of front bumper.
12" heavy duty front bumper with full wrap around. To be painted L0318EG metallic silver.
3/16" Front Bumper Gravel Shield. Smooth plate painted with black Durabak.
Recessed winch receiver in front bumper for model QM5000 portable winch. Includes swing down front center section of bumper for winch access, bumper reinforcement, winch enclosure, raised lid, and port winch wiring. For use on E‐ONE chassis with 10" high 28'' ext bumper only.
14" Front Bumper Gravel Shield Extension.
Overlay front heavy duty bumper with diamond plate panels.
Guard straps for bumper mtd recessed Q2B ‐ polished stainless steel.
PRICE
$1,360.00
$1,539.00
$483.00
$1,359.00
$779.00
$779.00
$139.00
$0.00
$0.00
$154.00
$294.00
$522.00
$691.00
$835.00
$43.00
$188.00
$779.00
$2,047.00
$1,962.00
$1,156.00
$827.00
$154.00
$2,386.00
$2,386.00
$827.00
$2,208.00
$2,207.00
$43.00
$2,386.00
$1,431.00
$5,173.00
$225.00
$408.00
$326.00
Option No.
1160‐0057
1160‐0058
1160‐0059
1160‐0060
1160‐0061
1160‐0062
1160‐0064
1160‐0065
1160‐0066
1160‐0067
1160‐0068
1160‐0069
1160‐0070
1160‐0071
1160‐0072
1160‐0073
1160‐0076
1160‐0080
1160‐0083
1160‐0084
1160‐0085
1160‐0086
Description
Rear bumper steel with dia plt overlay. Includes rubrail across rear surface and no step tags.
Trailer hitch ball and pintle hook combo kit.
10" Stainless steel front bumper with driver and officer side fog light cut‐outs and driver side (inboard of fog light) cut‐out for NFPA speaker. Includes frame mounted painted tow hooks, 20" bumper extension with center‐mounted hose storage tray with lid.
Dock bumpers (4) on front bumper equally spaced (as applicable).
10" heavy duty front bumper with full wrap around. To be painted L0318EG metallic silver.
PRICE
$1,626.00
$1,123.00
Rear bumper steel 8" deep with Gator Grip dia plt overlay. Includes rubrail across rear surface and handrail located below hosebed.
Heavy duty front bumper 10" high with full wrap around. To be painted [#COL].
Heavy duty front bumper 10" high with full wrap around. Center of bumper to have a 5" deep notch for recessed Q2B. Bumper to be painted job color.
License plate holder mounted driver side of front bumper.
Brush Guard Black with winch mount for Ford Super Duty Series. Includes tow hooks. Winch not included.
1/8" Front Bumper Gravel Shield. Smooth plate painted with black Durabak.
10" Stainless steel bumper with 4" extension. Includes driver side cut‐out for (1) ES‐100 speaker with grille, two (2) recessed mounted air horns with two (2) floor mounted foot switches. Custom ES.
10" Stainless steel bumper with 20" gravel shield extension. Includes driver side cut‐out for (1) ES‐100 speaker with grille, two (2) recessed mounted air horns with two (2) floor mounted foot switches. Custom ES.
10" Stainless steel bumper w/ 20" gravel shield extension. Includes center‐mounted hose storage tray w/ preconnect provision, hose tray lid, driver side cut‐out for (1) ES‐100 speaker w/ grille, and two (2) recessed mounted air horns w/ two (2) floor mounted foot switches. Custom ES.
10" Stainless steel bumper w/ 20" gravel shield extension. Includes front intake provision, center‐mounted hose storage tray w/ lid, driver side cut‐out for (1) ES‐100 speaker w/ grille, and two (2) recessed mounted air horns w/ two (2) floor mounted foot switches. Custom ES.
10" Stainless steel bumper w/ 20" gravel shield extension. Includes front intake provision, center‐mounted hose storage tray w/ preconnect provision, hose tray lid, driver side cut‐out for (1) ES‐100 speaker w/ grille, and two (2) recessed mounted air horns w/ two (2) floor mounted foot switches. Custom ES.
10" Stainless steel front bumper with driver side cut‐out for NFPA speaker. Includes 20" bumper extension with center‐mounted hose storage tray with lid.
10" Stainless steel front bumper with driver side cut‐out for NFPA speaker. Includes 20" bumper extension with center‐mounted hose storage tray with lid.
24" Bumper extension with 1/8" diamond plate gravel shield, 10" front stainless steel bumper with location for NFPA speaker and dual Hadley air horns with driver and officer foot switch controls.
Heavy duty 12" front bumper with full wrap around. To be painted job color.
6" Front Bumper Extension.
Removable number plate with mounting brackets. Locate centered on front bumper. Plate to be painted job color. Plate to be 8"W x 8"H. Lettering and/or graphics not included.
$2,040.00
$2,386.00
$0.00
$324.00
$2,386.00
$2,961.00
$43.00
$1,334.00
$1,431.00
$0.00
$889.00
$1,425.00
$1,425.00
$1,425.00
$0.00
$0.00
$3,442.00
$2,386.00
$0.00
$280.00
Option No.
1160‐0087
1160‐0088
1160‐0092
1160‐0093
1160‐0094
1160‐0095
1160‐0096
1160‐0097
1160‐0098
1160‐0099
1160‐0100
1160‐0101
1160‐0102
1160‐0103
1160‐0104
1160‐0105
1160‐0106
1160‐0107
1160‐0108
1160‐0109
1160‐0110
1160‐0111
1160‐0112
1160‐0115
1160‐0116
1160‐0117
Description
Brush Guard Stainless Steel with winch mount for Ford Super Duty Series. Includes tow hooks. Winch not included.
Removable number plate with mounting brackets. Locate [#LOC]. Plate to be painted job color. Plate to be 12"W x 8"H. Lettering and/or graphics not included.
3/16" ADT Bumper gravel shield, w/valve cut‐out(s), Wildland
Aluminum tapered channel front bumper with natural finish. Kenworth.
18" Front Bumper Gravel Shield Extension.
Heavy duty front bumper with full wrap around. To be painted FLNA 91733 silver.
Two (2) 1.5" diameter stainless steel bumper guide rods are to be offset mounted on the ends of the front bumper with 8.5" convex mirrors top mounted via stainless steel brackets. In addition each guidepost shall have a stainless steel reinforcement rod inserted in guidepost tubes for extra stiffness. The officers side mirror shall be 3" higher than drivers side.
Dock bumpers NYPD (placement per NYPD). Quality Custom Components model 32220 bumpers; (4) front and (4) rear.
10 GA brushed stainless steel overlay on front face of 10" heavy duty bumper.
12Ga stainless steel front bumper gravel shield painted with black Durabak. NYPD only.
Brush Guard Stainless Steel with winch mount and front receiver for Ford Super Duty Series. Winch not included.
Brush Guard Black with heavy duty bumper and winch mount for Ford Super Duty Series. Winch not included.
1/8" Front Bumper Gravel Shield. gravel shield will utilize the OEM bumper angles.
Rear bumper steel 8" deep with Gator Grip dia plt overlay. Includes rubrail across rear surface and handrail located horizontally below turntable access door.
Swing down front section of bumper. 10" front bumper only. Requires extended front bumper and bumper reinforcement.
Removable number plate with mounting brackets. Locate [#LOC]. Plate to be painted lower job color (if cab is painted two tone). Plate to be 14"W x 8"H. Lettering and/or graphics not included.
Tubular rear bumper shall be mounted on the rear of the unit.
10" Stainless steel front bumper with driver side cut‐out for NFPA speaker. Includes frame mounted painted tow hooks, 20" bumper extension (1/8" diamond plate) with center‐mounted hose storage tray with red vinyl cover.
3/16" Front Bumper Gravel Shield. Smooth plate painted with black Scorpion coating.
10" Front Bumper Gravel Shield Extension.
Brush Guard Black with winch mount and front receiver for Ford Super Duty Series. Winch not included.
10" Stainless steel front bumper with driver side cut‐out for NFPA speaker. Includes 24" bumper extension for booster reel.
10" Stainless steel front bumper with driver side cut‐out for NFPA speaker. Includes 24" bumper extension with center‐mounted hose storage tray with lid.
Brush Guard Stainless Steel Dodge 5500
Heavy duty front bumper 10" high with full wrap around. Driver side of bumper to have a 5" deep notch for recessed Q2B. Bumper to be painted job color.
License plate holder mounted driver side of front bumper.
PRICE
$3,136.00
$280.00
$1,188.00
$0.00
$409.00
$2,386.00
$1,017.00
$593.00
$613.00
$1,193.00
$3,358.00
$4,674.00
$640.00
$2,040.00
$1,238.00
$307.00
$727.00
$3,205.00
$1,431.00
$151.00
$1,830.00
$0.00
$0.00
$2,047.00
$2,961.00
$43.00
Option No.
1160‐0119
1160‐0120
1160‐0121
1160‐0122
1160‐0123
1160‐0124
1160‐0125
1160‐0126
1160‐0127
1160‐0128
1160‐0129
1160‐0130
1160‐0131
1160‐0132
1160‐0133
1160‐0134
1160‐0135
1160‐0136
1160‐0137
1160‐0138
1160‐0139
1160‐0140
1160‐0141
1160‐0142
1160‐0144
Description
Holmatro bulkhead fitting (fitting comes with hinged cover) shall be mounted to an angled mounting bracket which is mounted to the top of the driver side gravel shield. The mounting bracket shall enclose the lead lines feeding the rear of the bulkhead fitting as mounted on the angled bracket. The bracket shall be made of 1/8" aluminum diamond plate. Includes Core Technology hose (up to 10,000 PSI). The hose shall run from R7 compartment to the driver side front bumper gravel shield.
1/8" Front Bumper Gravel Shield. Includes 1" return break on each side of heavy duty bumper.
Diamond plate lower gravelshield. Located under side of the front bumper extension.
20" Front Bumper Gravel Shield Extension. The extension shall extend further forward and each side to align with the edge of the bumper.
10 GA brushed stainless steel overlay on front face of 12" heavy duty bumper.
Heavy duty 12" front bumper with full wrap around. To be painted the same as the upper area two tone job color.
Heavy duty front bumper 10" high with full wrap around. Officer side of bumper to have a 5" deep notch for recessed Q2B. Bumper to be painted job color.
Dock bumpers NYPD (placement per NYPD). Buyers Products Company model B4000 bumpers; (4) front and (4) rear.
2" lip on rear and sides of gravelshield. See photos on file with sales.
Bumper guide (PR). RoDon 60" red/white fiberglass with spring mount. To be installed at final inspection.
License plate holder hinge mounted below center of front bumper.
Rear bumper steel 8" deep with Gator Grip dia plt overlay and angled (Boston style) style corners. Includes rubrail across rear surface and handrail located below hosebed.
1/8" Front Bumper Gravel Shield for heavy duty bumper. Includes 1" turn down around perimeter of HD bumper.
Notch front bumper for low "S" type front intake. Tray below pipe extending from cab to bumper. Tray to hold 15' of 5" LDH. Include nylon strap (seat belt type) for tray.
Heavy duty front bumper 10" high with full wrap around. Center of bumper to have a 5" deep notch for recessed Q2B. Bumper to be painted 2‐tone job color.
28" Front Bumper Gravel Shield Extension for recessed crosslay to be used on commercials only.
Two (2) 1.5" diameter stainless steel bumper guide rods are to be offset mounted on the ends of the front bumper with convex mirrors top mounted via stainless steel brackets (10" driver, 8" officer). In addition each guidepost shall have a stainless steel reinforcement rod inserted in guidepost tubes for extra stiffness. The officers side mirror shall be 3" higher than drivers side.
Bumper guide pinned (PR).
Heavy duty 12" front bumper with full wrap around. To be painted [#COL].
3/16" Front Bumper Gravel Shield. Extend shield to flush with heavy duty bumper edge.
20" Front Bumper Gravel Shield Extension for recessed crosslay to be used on commercials only.
3/16" Front Bumper Gravel Shield for heavy duty bumper. Includes 1" turn down around perimeter of HD bumper.
3/16" Front Bumper Gravel Shield with 1" turn down lips to protect the top edge of the heavy duty bumper from damage. Smooth plate painted with black Durabak.
Front frame extensions to be drop style IPOS. Includes integral tow eyes below bumper.
Heavy duty 12" front bumper with full wrap around. Center of the bumper to be extended (boxed out) for Q2B to be recessed without intruding into the bumper trays, recessed crosslays or any other options as applicable. To be painted [#COL].
PRICE
$4,307.00
$169.00
$814.00
$598.00
$629.00
$2,386.00
$2,961.00
$593.00
$460.00
$196.00
$84.00
$2,183.00
$228.00
$2,046.00
$2,961.00
$2,977.00
$1,017.00
$533.00
$2,386.00
$567.00
$2,664.00
$365.00
$1,485.00
$737.00
$3,087.00
Option No.
1160‐0145
1160‐0146
1160‐0147
1160‐0148
1160‐0149
1160‐0151
1160‐0152
1160‐0153
1160‐0154
1160‐0155
1160‐0156
1160‐0157
1160‐0158
1160‐0159
1160‐0160
1160‐0161
1160‐0162
1160‐0163
1160‐0164
Description
Notch front bumper for low "S" type front intake. 10" deep tray below pipe extending from cab to bumper to hold at minimum 25' of 5" LDH. Include nylon strap (seat belt type) for tray.
Custom built Stainless Steel 10" high front bumper. Requires extended front bumper.
PRICE
Heavy duty front bumper 10" high with full wrap around. To be constructed of 110,000 PSI frame rail material and painted job color.
Smooth aluminum plate with gold Scotchlite centered on front bumper. 6" x 36" with radius corners.
LINE‐X bumper package: Includes all visible diamond plate surfaces including gravel shield, exterior surface of trays and lids(flat or raised). If equipped, exterior of the fabricated booster reel housing, fabricated box for booster reel rollers and winch access door shall be included in this package.
20" front bumper extension with gravel shield for Ford. Includes relocating OEM bumper and tow eyes / hooks.
Rear bumper with 3" square bolt‐on stainless steel tube for rear guard. Includes no step tags. No rub rail or cover plate and rear marker lts attached to lower rear body surface. Note rear bumper to be exposed as natural surface un‐painted.
Heavy duty front bumper 10" high with full wrap around for commercial chassis. Center of bumper to have a 5" deep notch for recessed Q2B. Bumper to be painted job color. To include one piece modular mounting bracket for commercial chassis with welded integral front frame extension mounting rails for added durability and strength.
Heavy duty front bumper 12" high with full wrap around. Driver side of bumper to have a 5" deep notch for recessed Q2B. Bumper to be painted job color.
LINE‐X bumper: The bottom lip of the bumper shall have LINE‐X finish.
Durabak Black bumper package: Includes all visible plate surfaces including gravel shield, exterior surface of trays and lids(flat or raised). If equipped, exterior of the fabricated booster reel housing, fabricated box for booster reel rollers and winch access door shall be included in this package.
Heavy duty front bumper 10" high with full wrap around. Center of bumper to have a 5" deep notch for recessed Q2B. Corners to be tapered for an 8" wide mounting area. (Not available with reel trays). Bumper to be painted job color.
Heavy duty 12" front bumper with full wrap around. Corners to be tapered for an 8" wide mounting area. (Not available with reel trays). To be painted job color.
30" Front Bumper Gravel Shield Extension.
Rear bumper steel 8" deep with Gator Grip dia plt overlay and angled (Boston style) style corners. Includes rubrail across rear surface and (2) 10" handrails located vertically at rear of body.
Diamond plate overlay on the sides and angled corners of heavy duty bumper.
Heavy duty 12" front bumper with full wrap around. Center of bumper to have a 5" deep notch for recessed Q2B. Corners to be tapered for an 8" wide mounting area. (Not available with reel trays). To be painted job color.
$3,578.00
$239.00
Rear bumper with 4" square steel tube for rear guard. Includes no step tags. No rub rail or cover plate and rear marker lts attached to lower rear body surface. Note rear bumper to be painted job color with Boston style corners cut at 30 degree angle on each end.
Heavy duty inner city front bumper 10" high with full angle corners. Includes support wings for angled corners. Center of bumper to have a 5" deep notch for recessed Q2B. Bumper to be painted job color.
$2,046.00
$2,678.00
$960.00
$3,300.00
$2,273.00
$3,701.00
$2,961.00
$223.00
$960.00
$3,167.00
$2,592.00
$1,002.00
$2,183.00
$359.00
$3,167.00
$2,273.00
$3,270.00
1160‐0165
1160‐0166
Description
Heavy duty front bumper 10" high with full wrap around. Officer side notched for front intake recessed as much as possible. Bumper to be painted job color.
26" Front Bumper Gravel Shield Extension.
1160‐0167
1160‐0168
Heavy duty 12" front bumper with full wrap around. Center of bumper to have a 5" deep notch for recessed Q2B. Officer side notched for front intake recessed as much as possible. Corners to be tapered for an 8" wide mounting area. To be painted job color.
Heavy duty bumper wrap around lower edge guard. Extends from bottom of stripe to bottom of bumper.
Option No.
1160‐0169
1160‐0170
1160‐0171
1160‐0172
1160‐0173
1160‐0174
1160‐0175
1160‐0176
1160‐0177
1160‐0178
1160‐0180
1160‐0181
1160‐0182
1160‐0183
1160‐0184
1160‐0185
1160‐0186
1200‐0016
Heavy duty 12" front bumper with full wrap around. Driver side of bumper to have a 5" deep notch for recessed Q2B. Officer side notched for front intake recessed as much as possible. Corners to be tapered for an 8" wide mounting area. To be painted job color.
3/16" Front Bumper Gravel Shield with 1" turn down lip. Smooth plate painted with LINE‐X.
Heavy duty 12" front bumper with full wrap around. Driver side of bumper to have a 5" deep notch for recessed Q2B. Officer side notched for front intake recessed as much as possible. To be painted job color.
Rear bumper steel 8" deep with Gator Grip dia plt overlay and angled (Boston style) style corners. Includes a 4" square steel tube and additional bracing for support, rubrail across rear surface (if applicable) and handrail located below hosebed.
Rear bumper steel 8" deep with Gator Grip dia plt overlay. Includes a 4" square steel tube and additional bracing for support, rubrail across rear surface (if applicable) and handrail located below hosebed.
Heavy duty 12" front bumper with full wrap around. Driver side of bumper to have a 5" deep notch for recessed Q2B. Corners to be tapered for an 8" wide mounting area. (Not available with reel trays). To be painted job color.
Zinc flame spray coating for heavy duty front bumper (outside and inside surfaces) prior to painting.
3/16" smooth plate front bumper gravel shield with DA finish.
Heavy duty 10" front bumper with full wrap around. Corners to be tapered for an 8" wide mounting area. (Not available with reel trays). To be painted job color.
Heavy duty inner city front bumper 10" high with full angle corners. Includes support wings for angled corners. Driver side of bumper to have a 5" deep notch for recessed Q2B. Officer side of bumper to have notch for front suction. Bumper to be painted job color.
Hose deflector stainless steel pin to protect against hose pinch on Drivers side front bumper extension and cab corner.
Front intake swivel stop bracket to be located so it will eliminate the swivel from hitting the cab.
Diamond plate overlay on the front, sides and angled corners of heavy duty bumper.
Number plate, removable size to fit applicable to location on front bumper. Spaced out from face of bumper so plate can be removed. Location: [#LOC].
14GA polished stainless steel overlay on front face of 12" heavy duty bumper.
Scorpion bumper package: Includes all visible diamond plate surfaces including gravel shield, exterior surface of trays and lids(flat or raised). If equipped, exterior of the fabricated booster reel housing, fabricated box for booster reel rollers and winch access door shall be included in this package. Color: job color.
2" lip on rear and sides of gravelshield. Includes 1" radius on corners. See photos on file with sales.
Transmission Lockout 5/6 Gear
PRICE
$3,167.00
$763.00
$3,527.00
$278.00
$3,527.00
$1,325.00
$3,527.00
$2,183.00
$2,040.00
$3,167.00
$498.00
$139.00
$2,586.00
$3,870.00
$221.00
$251.00
$403.00
$188.00
$613.00
$1,160.00
$460.00
$0.00
Option No.
1200‐0017
1200‐0018
1200‐0020
1200‐0021
1200‐0022
1200‐0023
1200‐0024
1200‐0025
1200‐0065
1200‐0070
1200‐0076
1200‐0077
1200‐0078
1200‐0083
1200‐0096
1200‐0097
1200‐0098
1200‐0122
1200‐0126
1200‐0133
1200‐0135
1200‐0137
1200‐0177
1200‐0200
1200‐0208
1200‐0220
1200‐0222
1200‐0223
1200‐0224
1200‐0234
1200‐0235
1200‐0237
1200‐0238
1200‐0239
Description
Push‐button transmission shift selector.
"T" handle transmission selector.
TransSynd synthetic transmission fluid for EVS3000.
TransSynd synthetic transmission fluid for EVS 4000.
Conventional transmission fluid for EVS 3000.
Conventional transmission fluid for EVS 4000.
Speed range from 62 MPH to 67 MPH gear limited.
Speed maximum 75 MPH.
Transfer Case for All Wheel Drive‐ single speed with front axle declutch
Transmission dipstick ‐ extended length for filling from engine access door.
Transmission to be 4500 in place of the 4000. Gears 1 through 4 shall be programmed as "D" (Drive). Gear 5 to be programmed to activate via "mode" switch on shifter.
Transmission re‐programming. ''D'' allows trans to shift from 1st ‐ 3rd gear and ''Mode'' allows 4th gear.
Speed maximum 70 MPH
Transmission re‐programming. ''D'' allows transmission to shift from 1st ‐ 4th gear, and ''Mode'' allows 5th gear.
Electronic speed limiting set at 60 MPH.
Electronic limiting of speed to 68 MPH maximum. Note: Max speed may be set at 65 MPH due to tire rating.
Electronically limited speed to 62 MPH.
Electronic speed limiting set to 60 MPH.
Chassis speed to be electronic limited and not to exceed a maximum of 68 MPH. Note: Speed rating may be lower based on OEM tire ratings/top speed limitations provided on chassis.
Transmission cooler. Extreme hot climate units only.
A RGA transfer case will be installed for hook up of PTO needed accessories. This will include drive line and mounting brkts.
Electronic speed limiting set to 60 MPH.
Electronically limited speed to 68 MPH.
Eng/Trans Cummins ISX12 450HP with EVS4000 transmission. 2010 EPA Compliant.
Compression brake. Provided by the chassis OEM.
6 speed transmission with 6.14 gears for an estimated speed of 66MPH.
Stainless steel transmission yoke shield.
Eng/Trans Cummins ISX15 550HP with EVS4000 transmission. 2010 EPA Compliant.
Transmission re‐programming to allow for 6th gear (lower engine speed/better fuel economy). Rear axle gearing will be the same as used with 5 speed transmission.
Eng/Trans Cummins ISL 350HP/EVS3000 2013 EPA compliant engine.
Eng/Trans Cummins ISL 400HP/EVS3000 2013 EPA compliant engine.
Eng/Trans Cummins ISX12 400HP with EVS4000 transmission. 2013 EPA Compliant.
Eng/Trans Cummins ISX12 450HP with EVS4000 transmission. 2013 EPA Compliant.
Eng/Trans Cummins ISX12 500HP with EVS4000 transmission. 2013 EPA Compliant.
PRICE
$0.00
$1,627.00
$204.00
$321.00
$0.00
$0.00
$0.00
$0.00
$10,300.00
$0.00
$3,189.00
$720.00
$0.00
$720.00
$0.00
$0.00
$0.00
$0.00
$0.00
$2,375.00
$11,092.00
$0.00
$0.00
$128,743.00
$1,144.00
$0.00
$416.00
$137,364.00
$720.00
$86,152.00
$100,273.00
$128,507.00
$130,078.00
$131,648.00
Option No.
1200‐0241
1200‐0242
1200‐0243
1200‐0245
1200‐0269
1200‐0270
1200‐0280
1200‐0282
1200‐0283
1200‐0295
1200‐0309
1200‐0310
1200‐0311
1200‐0312
1200‐0313
1200‐0315
1200‐0316
1200‐0317
1200‐0318
1200‐0319
1200‐0320
1200‐0321
1200‐0322
1200‐0328
1200‐0332
1200‐0335
1200‐0337
1200‐0338
1200‐0339
1200‐0340
1200‐0341
1200‐0342
1200‐0343
1200‐0344
1200‐0345
Description
Eng/Trans Cummins ISX15 550HP with EVS4000 transmission. 2013 EPA Compliant.
Eng/Trans Cummins ISX15 600HP with EVS4000 transmission. 2013 EPA Compliant.
Chassis speed to be electronic limited and not to exceed a maximum of 65 MPH. Note: Speed rating may be lower based off OEM tire ratings provided on chassis.
Eng/Trans Cummins ISX12 500HP with EVS4500 transmission. 2013 EPA Compliant.
"T" handle transmission selector for International chassis only.
Eng/Trans Cummins ISL 380HP/EVS3000 2013 EPA compliant engine.
Transfer Case for HS chassis ‐ single speed with rear axle and pump declutches.
Eng/Trans Cummins ISX15 550HP with EVS4500 transmission. 2013 EPA Compliant.
Eng/Trans Cummins ISX15 600HP with EVS4500 transmission. 2013 EPA Compliant.
Transfer Case for HS chassis ‐ single speed with rear axle, pump and front drive axle declutches.
Eng/Trans Cummins ISL 330HP/EVS3000 2016 EPA compliant engine.
Eng/Trans Cummins ISL 350HP/EVS3000 2016 EPA compliant engine.
Eng/Trans Cummins ISL 380HP/EVS3000 2016 EPA compliant engine.
Eng/Trans Cummins ISL 400HP/EVS3000 2016 EPA compliant engine.
Eng/Trans Cummins ISL 450HP/EVS3000 2016 EPA compliant engine.
Eng/Trans Cummins ISX12 400HP with EVS4000 transmission. 2016 EPA Compliant.
Eng/Trans Cummins ISX12 450HP with EVS4000 transmission. 2016 EPA Compliant.
Eng/Trans Cummins ISX12 500HP with EVS4000 transmission. 2016 EPA Compliant.
Eng/Trans Cummins ISX12 500HP with EVS4500 transmission. 2016 EPA Compliant.
Eng/Trans Cummins ISX15 550HP with EVS4000 transmission. 2016 EPA Compliant.
Eng/Trans Cummins ISX15 550HP with EVS4500 transmission. 2016 EPA Compliant.
Eng/Trans Cummins ISX15 600HP with EVS4000 transmission. 2016 EPA Compliant.
Eng/Trans Cummins ISX15 600HP with EVS4500 transmission. 2016 EPA Compliant.
Eng/Trans Cummins ISX15 455HP with EVS4000 transmission. 2016 EPA Compliant.
Transmission re‐programming. ''D'' allows transmission to shift from 1st ‐ 5th gear, and ''Mode'' allows 6th gear overdrive. Requires overdrive option.
Cummins ISX12 500 HP engine.
Eng/Trans Cummins L9 330HP/EVS3000 2017 EPA compliant engine.
Eng/Trans Cummins L9 350HP/EVS3000 2017 EPA compliant engine.
Eng/Trans Cummins L9 380HP/EVS3000 2017 EPA compliant engine.
Eng/Trans Cummins L9 400HP/EVS3000 2017 EPA compliant engine.
Eng/Trans Cummins L9 450HP/EVS3000 2017 EPA compliant engine.
Eng/Trans Cummins L9 450HP/EVS3000 2017 EPA compliant engine. For use with HS rear engine chassis only.
Eng/Trans Cummins X15 565HP with EVS4000 transmission. 2017 EPA Compliant.
Eng/Trans Cummins X15 565HP with EVS4500 transmission. 2017 EPA Compliant.
Eng/Trans Cummins X15 600HP with EVS4000 transmission. 2017 EPA Compliant.
PRICE
$138,866.00
$142,315.00
$0.00
$133,673.00
$315.00
$94,625.00
$18,984.00
$140,890.00
$144,339.00
$21,427.00
$83,167.00
$86,152.00
$94,625.00
$100,273.00
$101,139.00
$128,507.00
$130,078.00
$131,648.00
$133,673.00
$138,866.00
$140,890.00
$142,315.00
$144,339.00
$135,051.00
$720.00
$0.00
$83,167.00
$86,152.00
$94,625.00
$100,273.00
$101,139.00
$101,139.00
$138,866.00
$140,890.00
$142,315.00
Option No.
1200‐0346
1225‐0005
1225‐0006
1225‐0008
1225‐0010
1225‐0011
1225‐0012
1225‐0013
1225‐0015
1225‐0016
1225‐0017
1225‐0020
1225‐0024
1225‐0025
1225‐0026
1225‐0027
1225‐0029
1225‐0030
1225‐0031
1225‐0035
1225‐0038
1225‐0039
1225‐0040
1225‐0041
Description
Eng/Trans Cummins X15 600HP with EVS4500 transmission. 2017 EPA Compliant.
Exhaust heat shield. Locate below compartment floor.
Exhaust tip stainless steel for Plymovent. For exhaust extraction system.
Wrap exhaust with heat tape from the turbo down to the flex pipe. Inspect after install for tears in material. Wrap outside with wire mesh to ensure material remains affixed.
Exhaust end for Nederman. For exhaust extraction system. Exhaust to discharge at 45 degree angle from body.
Vertical exhaust [#LOC]. Commercial chassis only.
Ward No Smoke Exhaust System.
Tailpipe support. Locate between tailpipe and body approx 10" in from edge of body.
Vertical exhaust officer side. This will include the vertical exhaust support.
Locate exhaust end between rear of compartment ahead of wheels and ahead of forward wheel well angle at approx. 45 degrees to rear.
Vertical exhaust elbow chrome plated 90 degree. Due to high heat from 2007 and later emission exhaust systems, dis‐coloring of exhaust end may occur after prolonged use.
Exhaust tip MagneGrip. For exhaust extraction system. Tip to protrude appox. 2" outside of body (Not rubrail).
Plymovent Grabber magnetic exhaust end. Bolt‐on for exhaust extraction system.
Vertical exhaust officer side. This will include the vertical exhaust support. Locate to forward area of module (internal) with exhaust end being approx. 6" above ladders stowed on ladder rack.
Vertical exhaust rain cap, chrome.
Vertical exhaust officer side. This will include the vertical exhaust support. Aerial vertical exhaust to be plumbed through (internal) right rear of pump module. Top of pipe to turn out.
PRICE
$144,339.00
$198.00
$373.00
$890.00
$0.00
$0.00
$18,534.00
$563.00
$1,725.00
$255.00
$328.00
$683.00
$456.00
$1,953.00
$95.00
$2,571.00
Exhaust end modification for Nederman. For exhaust extraction system. Exhaust to discharge at 45 degree angle from body. Wildland.
Exhaust driver side terminating between L3/L4
Wrap exhaust with heat tape from the turbo down to the muffler. Visually inspect after install for tears in material. Wrap outside with wire mesh to keep material from coming off.
$100.00
$657.00
Exhaust end for Plymovent. For exhaust extraction system. Exhaust to be angled rearward to allow for possible deflection if impacted.
Vertical exhaust officer side. This will include the vertical exhaust support. Locate to forward area of pump module, outboard of deck gun support, rearward of crosslay with exhaust end being approx. 13" above the top of the pump module. End of pipe will be straight cut (no elbow) and shall be modified after delivery by local dealership with a Plymovent exhaust adaptor.
Modify the tailpipe to discharge straight out of a side panel located below R1 compartment but above the bottom edge of the body. Exhaust tip to be MagneGrip for exhaust extraction system. .
Vertical exhaust to have: TAIL PIPE (1) turnback type Bright for single exhaust and Muffler/Tail Pipe Guard (1) Bright Stainless Steel. International 7400 chassis.
Exhaust modification to add stiffeners to the standard exhaust stack to stabilize exhaust for Plymovent application.
$507.00
$942.00
$0.00
$1,028.00
$318.00
$426.00
1225‐0062
Description
Exhaust end for Plymovent. For exhaust extraction system. Set back approx. 4" from exhaust end. Includes "Caution Hot" label above exhaust on side of body.
Exhaust end for Nederman. For exhaust extraction system. Extend tail pipe 2" past side of body (Not rubrail).
Vertical exhaust supplied by Freightliner IPO std horizontal. RH back of cab Tradition base spec 1005‐0517
Stainless steel exhuast system ipos. Export only.
Exhaust. Vertical exhaust provision on rescue body. Includes vertical exhaust support, flue sheet metal thru lower body compartment to upper body, insulation between exhaust stack and body sheet metal, stack heat shield if applicable & warning tags for heat exposure inside body compartment and dunnage area as applicable. Locate: officer side.
Exhaust outlet cooling tip.
Vertical exhaust. M2 106 with ISL 330 HP 2013 EPA commercial chassis only. 114 inches high. Locate: officer side.
Vertical exhaust stack pipe straight chrome plated with rain cap. Due to high heat from 2007 and later emission exhaust systems, dis‐
coloring of exhaust end may occur after prolonged use.
Vertical exhaust officer side through body forward of R2. This will include shortening the existing standard tailpipe and adding the vertical exhaust to standard lower exhaust piping from connection point below rear section of R1 forward of wheel in supplied body cavity. Exhaust stack shall be mounted to supplied body provisions and shall have aluminized piping from lower elbow as attached to existing tail pipe up to upper stack. The upper stack and rain bonnet flap shall be chrome and shall extend up through outer compartment top to available OAH per customer requirements or Approx. 15.50" to topmost bonnet point. The bonnet shall be positioned where it opens outward of the body to expell exhaust away from apparatus.
Locate exhaust end 3" below rubrail extending 2" past rubrail.
Vertical exhaust officer side.
Re‐route vertical exhaust to below body. Includes heat wrap as necessary. Metro 100 only.
Nederman exhaust transmitter on cab dash. Wired through engine run.
Ward No Smoke 2 Exhaust System.
Exhaust end with fresh air vent for Plymovent exhaust extraction system.
Modification to OEM exhaust. Modify commercial exhaust tail pipe aft of DPF supplied by commercial OEM to transition and connect to E‐1 vertical exhaust provision.
Wrap exhaust with heat tape. Wrape the vertical exhaust componet that passes thru the rear body compartment area with heat tape. Includes outside wrap with wire mesh to protect heat wrap.
1225‐0063
1225‐0064
1225‐0065
1250‐0003
1250‐0004
1250‐0005
1250‐0006
1250‐0009
Wrap exhaust with thermal insulation tape from the turbo down to the DPF (not including flex pipe if equipped). Includes S/S tie wraps.
Vertical exhaust driver side. This will include the vertical exhaust support.
The exhaust outlet shall be vertical. (Metro 100 only)
Frame 10.25 x 3.5 x .375 chassis.
Frame ‐ Torque box for HP95 Mid‐Mount aerial.
Frame ‐ Torque box for tandem axle RM aerial.
Frame liner 9.375 x 3.125 x .375.
Frame ‐ Torque box for Tiller.
Option No.
1225‐0043
1225‐0044
1225‐0045
1225‐0046
1225‐0047
1225‐0048
1225‐0049
1225‐0050
1225‐0052
1225‐0054
1225‐0055
1225‐0056
1225‐0057
1225‐0059
1225‐0060
1225‐0061
PRICE
$309.00
$0.00
$628.00
$2,609.00
$2,809.00
$252.00
$0.00
$417.00
$1,158.00
$255.00
$0.00
$1,309.00
$1,138.00
$18,534.00
$547.00
$1,309.00
$942.00
$246.00
$2,379.00
$0.00
$5,908.00
$22,177.00
$22,870.00
$3,253.00
$76,948.00
Option No.
1250‐0010
1250‐0011
1250‐0013
1250‐0014
1250‐0015
1250‐0016
1250‐0017
1250‐0018
1250‐0019
1250‐0020
1250‐0021
1250‐0022
1250‐0023
1250‐0024
1250‐0025
1250‐0026
1250‐0027
1250‐0028
1250‐0029
1250‐0030
1250‐0031
1250‐0032
1250‐0033
1250‐0034
1250‐0035
1250‐0036
1250‐0056
1250‐0057
1250‐0058
1250‐0061
1250‐0062
1250‐0063
1250‐0064
1250‐0065
Description
Frame rail liner for commercial chassis
Rear underbody support frame.
Main frame ‐ 12.0x3.5x.375 with 11.125 liner and 10" step. Step frame ‐ 10.25x3.5x.375 with 9.375 liner.
Frame ‐ Torque box for HP100 platform.
Frame assembly to include 176" wheelbase and 41" framecut.
Frame assembly to include 196" wheelbase and 41" framecut.
Frame assembly to include 210" wheelbase and 41" framecut.
Frame assembly to include 182" wheelbase and 47" framecut.
Frame assembly to include 202" wheelbase and 47" framecut.
Frame assembly to include 216" wheelbase and 47" framecut.
The wheel base of this apparatus must be 4" longer than stated under the commercial chassis line item. This is due to the 2007 EPA exhaust requirements.
Frame assembly to include 212" wheelbase and 47" framecut.
Frame assembly to include 192" wheelbase and 47" framecut.
Frame assembly to include 220" wheelbase and 47" framecut.
Frame 12 x 3.5 x .375 chassis.
Frame liner 11.125 x 3.125 x .375.
Frame ‐ Torque box for tandem axle RM aerial with no waterway pipe.
Rear heavy duty underbody support frame.
Torque box modifications to allow for Hendrickson FIREMAAX tandem air ride suspension (for use with HM100/110 and HP100).
Frame assembly to include 220" wheelbase and 41" framecut.
Frame assembly to include 206" wheelbase and 41" framecut.
Frame assembly to include 186" wheelbase and 41" framecut.
Frame assembly to include 220" wheelbase and 41" framecut.
Frame assembly to include 192" wheelbase and 47" framecut.
Frame assembly to include 212" wheelbase and 47" framecut.
Frame assembly to include 226" wheelbase and 47" framecut.
Frame rails shall have access holes sealed to prevent road debris from accumulating. Access hole covers shall be removable.
Rear underbody support frame. SS product.
Framerails to have no additional holes (as applicable). To be designed for NYPD application.
Frame liner "L" 8.875 x 3.125 x .375.
Frame ‐ Torque box for HP100 platform with 6" w/way pipe. For use with industrial applications only.
Frame ‐ Torque box for single axle RM aerial.
Frame ‐ Torque box for HP100 platform with 5" w/way pipe. For use with 2000 GPM waterway flow. May affect ground ladder storage in tunnel.
Rear chassis subframe for Urban Interface pumper. Raises bottom of chassis approx 4". For use with 12" frame rails and FS‐25 front axle only.
PRICE
$0.00
$621.00
$22,611.00
$29,663.00
$19,223.00
$19,223.00
$19,223.00
$19,223.00
$19,223.00
$19,223.00
$0.00
$19,223.00
$19,223.00
$19,223.00
$5,908.00
$3,620.00
$20,824.00
$1,655.00
$1,793.00
$19,223.00
$19,223.00
$19,223.00
$19,223.00
$19,223.00
$19,223.00
$19,223.00
$2,113.00
$621.00
$462.00
$3,019.00
$32,143.00
$20,987.00
$32,049.00
$2,480.00
Option No.
1250‐0066
1250‐0067
1250‐0068
1250‐0069
1250‐0070
1250‐0071
1250‐0072
1250‐0073
1250‐0074
1250‐0075
1250‐0076
1250‐0077
1250‐0078
1250‐0080
1250‐0081
1250‐0082
1250‐0083
1250‐0084
1250‐0085
1250‐0086
1350‐0000
1350‐0001
1350‐0002
1350‐0003
1350‐0004
1350‐0005
1350‐0006
1350‐0008
1350‐0009
1350‐0010
Description
Rear chassis subframe for 4x4. Raises bottom of chassis 9.375". For use with 12" frame rails and AxleTech 4000 or equivalent front axle only.
Chassis frame rails shall be zinc plated (galvanized) IPOS. Includes rear subframe rails (if applicable).
Chassis frame rails, front frame extensions, rear subframe (Urban Interface), crossmembers and battery brackets shall be zinc plated (galvanized) IPOS.
Chassis frame rails, front frame extensions, rear 4x4 / 6x6 subframe, crossmembers and battery brackets shall be zinc plated (galvanized) IPOS.
Chassis frame liner shall be zinc plated (galvanized) IPOS.
Frame ‐ Formed torque box for HP95 Mid‐Mount aerial.
Torque box modifications to allow for Hendrickson FIREMAAX tandem air ride suspension (for use with CR100/137, 95‐Platform and HP100 Platform).
Frame ‐ Formed torque box for HP95 Mid‐Mount aerial. Includes 12" high rails below cab.
Rear underbody support frame with side tow eye style frame brackets without lower tow eyes to minimize impact on departure angle. To be used with frame mounted tow eyes facing rearward from frame rails.
Forward outriggers on torque box shifted forward 10". Only available on HP100 Platform with 260" wheelbase.
Rear underbody support frame. Includes zinc plated (galvanized) IPOS.
Frame ‐ Torque box for HP100 platform with no waterway pipe.
Zinc flame spray coating for integral torque box chassis.
Frame assembly with 10.25 x 3.5 x .375 powder coated galvanized rails.
Frame assembly with 12 x 3.5 x .375 powder coated galvanized rails.
Frame assembly with powder coated galvanized rails and 10" step for use with front drive axle. Includes 12 x 3.5 x .375 rails behind cab with 11.125 liner and 10.25 x 3.5 x .375 rails below cab with 9.375 liner.
Frame liner 9.375 x 3.125 x .375, galvanized and powder coated.
Frame liner 11.125 x 3.125 x .375, galvanized and powder coated.
Front chassis frame extensions, crossmembers and battery brackets shall be zinc plated (galvanized) IPOS. Includes rear subframe if applicable (urban interface, straight frame 4x4, etc).
Frame ‐ Torque box for single axle Metro 100 Quint aerial.
Electric reprime diesel fuel pump. Not available on E‐One custom chassis.
Dual fuel fill package. Additional fuel fill provided on officer side of unit.
Recessed fuel fill
Fuel system 50 gallon.
Fuel system 50 gallon saddle tanks.
Fuel system 65 gallons.
Fuel system 100 gallons
Fuel water separator Fuel‐Pro 382 (Cummins FH2309). Filter is top serviceable.
Fuel line hose braided. Includes fuel pick‐up (if applicable).
Fuel pick‐up for generator or pump. Includes hoses run to generator compartment.
PRICE
$2,979.00
$2,123.00
$5,131.00
$5,543.00
$544.00
$22,177.00
$3,170.00
$22,177.00
$1,060.00
$536.00
$1,472.00
$27,617.00
$5,333.00
$5,908.00
$5,908.00
$22,611.00
$3,253.00
$3,620.00
$3,008.00
$20,987.00
$768.00
$543.00
$141.00
$1,617.00
$2,779.00
$1,707.00
$2,447.00
$740.00
$316.00
$147.00
Option No.
1350‐0011
1350‐0012
1350‐0013
1350‐0014
1350‐0016
1350‐0022
1350‐0023
1350‐0025
1350‐0026
1350‐0027
1350‐0028
1350‐0029
1350‐0030
1350‐0032
1350‐0034
1350‐0035
1350‐0036
1350‐0037
1350‐0038
1350‐0039
1350‐0040
1350‐0041
1350‐0042
1350‐0043
1350‐0044
1350‐0045
1350‐0046
1350‐0048
1350‐0049
1350‐0050
1350‐0051
1350‐0052
1350‐0053
1350‐0054
1350‐0055
Description
Fuel pump electric w/re‐prime.
Fuel shut‐off valve. Location: [#LOC].
Racor fuel/water separator to be a bottom drop out style. Shall include indicator light and audible alarm.
Thermal control in‐line fuel heater.
Fuel Fill Package. Required on chassis with approved factory tank.
Fuel line hose rubber.
Fuel cooler, to be routed from the discharge side of the pump to the chassis fuel line. Cooler to be functioning when the pump is in operation.
Fuel line hose braided. Includes re‐usable fittings on both ends of the hose.
Fuel Lines Wrapped in Thermal Loom
Fitch fuel catalyst drop in style
Additional Fuel Sender in tank. For future use only. No wiring.
Racor fuel separator. To allow fuel flow to primary or secondary (back‐up) fuel separator. Control valve to be located in pump compartment access in walkway with labeling. Locate adjacent to primary Racor unit.
Fuel water seperator to be mounted outboard of the driver's side frame rail in the pump module area.
A fuel water seperator heater and alarm will be added to the current system.
Racor separator 12 volt heated fuel / water, bottom drop out style (w/o alarm).
24 volt heated fuel/ water Racor separator to be a bottom drop out style.
Fuel water Racor separator light and audible alarm (w/o heat).
Fuel system w/65 gallon stainless steel tank.
Fuel water seperator with a heater, alarm and indicator light.
A fuel water seperator with heater will be added to the current Detroit Diesel system.
Fuel system 50 gallon stainless steel saddle tanks.
Fuel line service loop for tank maintenance. 4' loop coiled above fuel tank(s).
A 56 gallon aluminum fuel tank with 9 gallon DEF. tank to be located [#LOC].
Fuel system w/50 gallon stainless steel tank.
E.J. Ward Canceiver electronic fuel monitoring system. Includes (2) sensors for dual fuel fill application.
Channel and rod mount fuel tank in addition to straps.
Fuel water separator Fuel‐Pro 382 with light and alarm. Filter is top servicable.
Fuel system 100 gallons. Tank located above framerails to rear of cab.
Fuel system 85 gallons. Tank located above framerails to rear of cab.
Fuel system 60 gallon saddle tanks.
Locate fuel/water seperator up high. Mount directly to cab tilt lock bracket.
Fuel system 75 gallons.
Racor model 4120R1230 fuel/water separator.
Fuel water separator Fuel‐Pro 382 with light and alarm. Filter is top servicable.
Fuel system w/100 gallon stainless steel tank.
PRICE
$449.00
$115.00
$781.00
$520.00
$391.00
$0.00
$497.00
$316.00
$931.00
$854.00
$396.00
$1,218.00
$0.00
$523.00
$336.00
$362.00
$117.00
$2,999.00
$695.00
$351.00
$5,417.00
$99.00
$0.00
$2,756.00
$3,100.00
$573.00
$854.00
$2,447.00
$2,447.00
$3,285.00
$0.00
$2,077.00
$869.00
$854.00
$3,341.00
Option No.
1350‐0056
1350‐0057
1350‐0058
1350‐0059
1350‐0060
1350‐0061
1350‐0062
1350‐0063
1350‐0064
1350‐0065
1350‐0066
1350‐0067
1350‐0068
1400‐0002
1400‐0003
1400‐0010
1400‐0011
1400‐0012
1400‐0013
1400‐0014
1400‐0019
1400‐0020
1400‐0021
1400‐0023
1400‐0024
1400‐0026
1400‐0027
1400‐0028
Description
Fuel system w/65 gallon tank below cab. HS chassis only.
Fuel line hose silicone.
Radiator mounted fuel cooler.
Fuel system w/65 gallon stainless steel tank below cab. HS chassis only.
Fuel system 60 gallon stainless steel saddle tanks.
Fuel system 70 gallons.
Fuel tank vent lines to be extended below frame rails and secured with metal clamps.
Fuel fills on each side of vehicle to be labeled "ULTRA LOW SULFUR DIESEL FUEL ONLY" with embossed metallic tags fastened in place with stainless steel hardware.
The exterior of the chassis fuel tank(s) shall be coated with LINE‐X.
The exterior of the battery tray(s) shall be coated with LINE‐X. Includes covers if equipped.
Fuel pick‐up for diesel compressor. Includes hoses run to compressor compartment.
Fuel system w/50 gallon stainless steel tank. Includes taper rear.
Fuel drain valve in place of plug.
Battery four group 31 1000 CCA.
Battery six group 31 1000 CCA.
Battery six Delco 1150 Hi‐Cycle 700 CCA.
Battery splash cover for ULC compliance.
Officer side front and middle batteries shall be Isolated for use with communication equipment only. The (2) batteries are not to be hooked up to the 12 Volt electric bus. Provide (3) 2AWG red cables and (1) 2AWG black cable from the location of the batteries through the officer side comm box to the driver comm box w/4ft of excess cable.
Battery four group 31 1000CCA. (3) batteries driver side, (1) battery officer side w/ available space for additional (2) batteries on officer side.
Mount (3) 100A fuses, (2) 40A fuses near officer batteries. 100A fuse to manual trip, manual reset type. Wire (3) 2AWG red battery cables from comm box to 100A fuses. Provide jumpers from fuses to batteries. Wire 8AWG wires from comm box to 40A fuses. Route 2AWG cables into officer comm box, under bottom shelf and up through inboard side of shelf. Route through wireway to driver side comm box. Leave 4ft of excess in comm box.
Special battery jumper stud location. Jumper studs to be located [#LOC].
Relocate custom chassis batteries. Location: [#LOC].
Six (6) Odyssey Group 31 1000CCA Batteries. Locate (3) each side of the chassis.
Battery six Delco 1110 Hi‐Cycle 750CCA.
Jumper studs to be located below driver's side front corner of body (or pump module if equipped). Studs to face down with positive stud outboard.
Black insulated battery terminal protectors shall be installed.
Additional set of jumper studs. Location: Opposite standard location.
Battery six Optima model D31T 900CCA.
PRICE
$1,707.00
$316.00
$514.00
$2,999.00
$5,923.00
$2,077.00
$0.00
$0.00
$504.00
$504.00
$587.00
$3,168.00
$115.00
$1,071.00
$1,601.00
$1,411.00
$324.00
$882.00
$1,337.00
$423.00
$380.00
$1,133.00
$4,077.00
$1,411.00
$229.00
$21.00
$390.00
$3,731.00
Option No.
1400‐0029
1400‐0031
1400‐0032
1400‐0033
1400‐0034
1400‐0035
1400‐0036
1400‐0037
1400‐0038
1400‐0039
1400‐0040
1400‐0041
1400‐0042
1400‐0043
1400‐0046
1400‐0047
1400‐0048
1400‐0049
1400‐0050
1400‐0051
1400‐0052
1400‐0053
1400‐0054
1400‐0055
1400‐0056
1400‐0057
1400‐0058
1400‐0059
1400‐0060
1400‐0061
1510‐0000
Description
Battery jump start system. Includes Anderson receptacle under officer side running board offset forward and 25' jumper cables with alligator clips and Anderson connector.
Stainless steel battery trays with stainless steel covers.
Battery five group 31 1000 CCA (two left / three right). For use with below cab DEF tank only.
Heater pads for (4) Group 31 battery system. Wire pads to block heater receptacle.
Stainless steel battery trays.
Batteries to be wired in a "cross‐charging" method as outlined in city spec. See details on file with sales.
Battery six group 31 1000CCA. Deka model 1231MF.
Battery rollout tray in body compartment R1.
Battery two 8D 1400 CCA.
Battery five Optima model D31T 900CCA.
Battery set additional two group 31 1000 CCA. Location: [#LOC].
Insulation on under side of battery tray assembly. NYPD only.
Jumper studs to be located below driver's side front corner of body (or pump module if equipped). Studs to face outboard.
Jumper studs to be located below driver's side front corner of body. Studs to face outboard.
Heater pads for (5) Group 31 battery system. Wire pads to winterization shoreline receptacle.
Battery six group 31 1000 CCA. For use with 67.5"/80" cab with 10G DEF under driver side of cab.
Battery five group 31 1000 CCA (two left / three right).
Battery six group 31 1000 CCA with post terminals. For use with 67.5"/80" cab with 10G DEF under driver side of cab.
(2) additional batteries located in R1 shall be Isolated for use with 24V winch. The (2) batteries are not to be hooked up to the 12 Volt electric bus.
(2) additional batteries located under the cab shall be Isolated for use with 24V winch. The (2) batteries are not to be hooked up to the 12 Volt electric bus.
Battery / Idle Mitigation System. Includes 200Ah power module (battery) on driver side and 300 Ah power module on officer side. For use with below cab DEF tank only.
Power module 500 Ah additional for Idle Mitigation System. Location: [#LOC]
Four(4) group 31 AGM 1150 CCA Odyssey PC‐2150 batteries.
Battery four group 31 1000 CCA. One battery left side (with DEF) and three on right side. For use with 44.5" cab only.
Officer side front battery isolated for use with 12V accessory system. The battery is not to be hooked up to the 12 Volt electric bus.
Battery five group 31 760 CCA (two left / three right). For use with below cab DEF tank only.
Battery, deep cycle. Two (2) 12V deep cycle batteries shall be provided. Isolated batteries shall be wired in series to provide 24VDC service to a CBRN system. Note: Batteries not to be connected to OEM chassis electric bus. Locate: L1 Aft.
Five (5) group 31 AGM 1150 CCA Odyssey PC‐2150 batteries. (two left / three right). For use with below cab DEF tank only.
Battery five Delco 1110 Hi‐Cycle 750CCA (two left / three right). For use with below cab DEF tank only.
Stainless steel picture frame hold down battery brackets. Allows for batteries to be serviced without removing cover.
Seat cavity cover (EA).
PRICE
$646.00
$1,595.00
$1,337.00
$1,093.00
$541.00
$577.00
$1,853.00
$732.00
$1,309.00
$3,301.00
$594.00
$116.00
$229.00
$229.00
$1,258.00
$2,483.00
$1,337.00
$3,038.00
$908.00
$908.00
$15,012.00
$12,371.00
$3,061.00
$1,071.00
$557.00
$1,337.00
$908.00
$3,825.00
$1,176.00
$333.00
$187.00
Option No.
1510‐0003
1510‐0004
1510‐0005
1510‐0007
1510‐0008
1510‐0009
1510‐0010
1510‐0035
1510‐0037
1510‐0038
1510‐0039
1510‐0040
1510‐0041
1510‐0042
1510‐0043
1510‐0044
1510‐0045
1510‐0046
1510‐0047
1510‐0048
1510‐0049
1510‐0050
1510‐0051
1510‐0052
1510‐0053
1510‐0054
1510‐0055
1510‐0056
1510‐0057
1510‐0058
1510‐0059
1510‐0060
1510‐0061
1510‐0062
1510‐0063
1510‐0064
1510‐0065
Description
Seats, Inc. brand 911 cab seats.
Seats, Bostrom brand.
Seat cover material Imperial 1200.
Seat cover material vinyl.
Seat color gray.
Seat color black.
Seat color burgundy
Universal air pack bottle bracket (EA). Location: [#LOC].
Seat cover material Durawear.
Driver seat 911 air ride.
Driver seat to be 911 air ride with SCBA back
Officer seat to be 911 air ride
Officer seat 911 air ride SCBA.
Officer seat to be 911 fixed SCBA.
Driver seat to be Bostrom air ride.
Driver seat to be Bostrom air ride with SCBA back
Officer seat to be Bostrom air ride.
Officer seat to be Bostrom air ride SCBA.
Officer seat to be Bostrom fixed SCBA.
Driver seat to be 911 electric.
Driver seat to be Bostrom electric.
Rear facing 911 seat with SCBA driver's side.
Engine cover 911 one man bench with SCBA
Engine cover 911 two man bench with SCBA.
Rear facing 911 seat with SCBA officer's side.
Rear facing Bostrom seat with SCBA driver's side.
Engine cover Bostrom one man bench with SCBA
Engine cover Bostrom two man bench with SCBA.
Rear facing Bostrom seat with SCBA officer's side.
Fold down 911 seat located [#LOC]
Fold down 911SCBA seat located [#LOC].
Fold down Bostrom seat located [#LOC].
Fold down Bostrom SCBA seat located [#LOC].
Two man bench centered on rear wall with 911 SCBA backs. Includes angled corners.
Two man bench centered on rear wall with Bostrom SCBA. Includes angled corners.
Four man bench centered on rear wall with 911 SCBA
Four man bench centered on rear wall with Bostrom SCBA.
PRICE
$0.00
$0.00
$0.00
$0.00
$0.00
$0.00
$0.00
$163.00
$0.00
$1,000.00
$1,188.00
$1,000.00
$1,188.00
$971.00
$1,106.00
$1,283.00
$1,106.00
$1,283.00
$1,075.00
$1,491.00
$1,594.00
$835.00
$1,093.00
$1,845.00
$835.00
$804.00
$1,123.00
$1,870.00
$804.00
$449.00
$990.00
$449.00
$931.00
$1,423.00
$1,754.00
$3,350.00
$3,084.00
Description
One man bench centered on rear wall with 911 SCBA
One man bench centered on rear wall with Bostrom SCBA
Three 911 SCBA seats rear facing, one outboard driver, one outboard officer, one centered.
Three 911 SCBA seats rear facing, one outboard driver, one outboard officer, one centered for top mount enclosed cab only. The outboard seats to be angled 30 degrees inward.
PRICE
$1,157.00
$1,262.00
$2,505.00
$2,689.00
$2,689.00
$1,068.00
$0.00
$2,142.00
$1,106.00
1510‐0082
1510‐0083
1510‐0084
1510‐0085
1510‐0086
1510‐0087
1510‐0088
1510‐0089
1510‐0090
Three Bostrom SCBA seats rear facing, one outboard driver, one outboard officer, one centered. For top mount enclosed cab only.
SEAT 911 3 RR FACING TME 30DEG
Tiller cab seating 911 air ride and flip down training seat.
Tag seat capacity one (1) for tiller cab only.
Bostrom SCBA seats forward facing center of rear wall (PR). Free standing with individual risers on rear wall.
Tiller cab seating Bostrom air ride and flip down training seat.
Three individual forward facing 911 Imperial 1200 gray attendant seats with flip up bottom seat cushions. Bottom cushions to be large as possible.
Rear Seat Riser Storage. Includes smooth plate doors with push‐button latches and 250lbs. slide out trays‐ (1) each side. Compartment opening to be 17" w x 10" h and transverse side to side. Riser to be Zolatone gray.
Officer seat to be 911 attendant.
Cab occupant detection seating system. Wired to visual indicator (hazard light). Includes audible alarm. Requires multiplex electrical system.
Zico Quic‐Hold mechanical air pack bottle bracket for 5'' bottle (ea). Model MWAB with adjustable footplate and pull release strap. Location: [#LOC].
911 Attendant seat with individual riser (PR). Locate centered on rear wall.
Officer seat to be Bostrom electric
Custom logo embroidery (EA). Bostrom seats only. Requires set‐up sales code.
Embroidery set‐up for Bostrom cab seats.
Center rear wall seats to be mounted approximately 11" apart.
911 SCBA seats forward facing center of rear wall (PR). Free standing mtd on a common seat riser.
Tailbone pad for jump seat(s). (Reference print #634894)
One man bench (PR) on rear cab wall with Bostrom SCBA back. Location: driver and officer side outboard.
$589.00
$2,393.00
$1,594.00
$143.00
$727.00
$254.00
$2,237.00
$53.00
$1,757.00
1510‐0091
1510‐0092
1510‐0093
1510‐0094
1510‐0095
1510‐0096
1510‐0097
Zico Quic‐Hold mechanical air pack bottle bracket (EA). Model QLM‐U with adjustable footplate and pull release. Location: [#LOC].
Two man bench centered on rear wall with bench seat style back cushion and angled riser corners.
Custom logo embroidery (EA). Seats Inc. seats only. Requires set‐up sales code.
Embroidery set‐up for Seats Inc. 911 cab seats.
Driver seat Bostrom electric with integral seat belt.
Officer seat Bostrom electric with SCBA back with integral seat belt.
Rear facing seat driver side Bostrom with SCBA back and integral seat belt.
$712.00
$1,372.00
$158.00
$964.00
$1,774.00
$2,113.00
$900.00
Option No.
1510‐0066
1510‐0067
1510‐0068
1510‐0069
1510‐0070
1510‐0071
1510‐0072
1510‐0073
1510‐0076
1510‐0077
1510‐0078
1510‐0079
1510‐0080
1510‐0081
$2,505.00
$2,893.00
$2,853.00
$703.00
$4,909.00
Option No.
1510‐0098
1510‐0099
1510‐0100
1510‐0101
1510‐0104
1510‐0105
1510‐0106
1510‐0107
1510‐0108
1510‐0109
1510‐0110
1510‐0111
1510‐0112
1510‐0113
1510‐0114
1510‐0116
1510‐0117
1510‐0118
1510‐0119
1510‐0120
1510‐0121
1510‐0122
1510‐0123
1510‐0124
1510‐0125
1510‐0126
1510‐0127
1510‐0128
1510‐0129
Description
Rear facing seat officer side Bostrom with SCBA back and integral seat belt.
Rear wall seat Bostrom flip‐up with SCBA back and integral seat belt. Location: [#LOC].
Padded headrest for fold down jump seat (EA). Not available with rear wall windows.
Driver and officer outboard rear facing seats mounted at 30 degree angle. Includes upper seat belt brkt. adjusted to rear of cab.
911 SCBA seat forward facing center of rear wall. Free standing mtd on seat riser.
One man bench (PR) on rear cab wall with Seats 911 SCBA back. Location: driver and officer side outboard.
911 SCBA seats forward facing rear wall (PR). Equally spaced with individual risers on rear wall.
Seats Talladega 910 hi‐back air suspended driver seat with 2 person bench. Rear seating area to have a 3 person bench seat.
Universal 911 Seating Package. Includes one (1) hi‐back air ride suspension driver seat, one (1) hi‐back fixed SCBA officer seat, and three (3) fixed SCBA rear seats. Tradition.
International Seating Package. Includes one (1) national brand air ride driver, Gra‐Mag (2) person fixed bench and a (3) person fixed bench seat. Tradition.
PRICE
$900.00
$1,248.00
$131.00
$519.00
$1,121.00
$1,426.00
$2,237.00
$0.00
Bostrom Seating Package. Includes one (1) air ride driver seat, one (1) fixed SCBA officer seat and (3) fixed SCBA rear seats. Tradition.
Seating Package Two (2) Door Freightliner. Includes One (1) Talladega 910 Hi‐Back Air Ride Driver and One (1) 911 Fixed Officer (Non‐
SCBA).
$1,948.00
Seating Package Two (2) Door Freightliner. Includes One (1) Talladega 910 Hi‐Back Air Ride Driver and a Two (2) Person Bench Seat.
Seating Package Two (2) Door International. Includes One (1) Nat'l Brand Air Ride Driver and Two (2) Person Bench Seat.
Seating Package Two (2) Door International. Includes One (1) Nat'l Brand Air Ride Driver and One (1) Nat'l Brand Air Ride Officer (Non‐
SCBA).
Fold‐down seat located [#LOC].
Bostrom SecureAll mechanical air pack bottle bracket (EA). Location: [#LOC].
Flip‐up 911 SCBA seat located [#LOC].
Flip up Bostrom SCBA seat located [#LOC].
Flip up 911 attendant seat located [#LOC].
Flip up Bostrom attendant seat located [#LOC].
Fold down seat with 911 SCBA back located [#LOC].
Fold down seat with Bostrom SCBA back located [#LOC].
Officer seat fixed Bostrom with SCBA back and integral seat belt.
Seating Package Two (2) Door International. Includes One (1) Bostrom Sierra 140 high back air suspended Driver seat and (1) Bostrom Tanker 400 ct non suspended SCBA Officer seat.
CrewGuard occupant seating detection system. Display location: [#LOC].
Additional CrewGuard display. Location: [#LOC].
FlameFighter air pack bottle bracket (EA). Model 17000 with adjustable footplate and push‐button release. Location: [#LOC]
Two man bench centered on rear wall with Bostrom SCBA backs for use with ALS provision with side access only. Includes (1) horizontally hinged door on the front of the rear bench seat for access to storage below bench.
$1,995.00
$0.00
$139.00
$0.00
$0.00
$114.00
$446.00
$567.00
$1,018.00
$1,051.00
$1,112.00
$1,238.00
$993.00
$1,008.00
$1,043.00
$545.00
$3,672.00
$293.00
$571.00
$2,217.00
Option No.
1510‐0130
1510‐0131
1510‐0132
1510‐0133
1510‐0134
1510‐0135
1510‐0136
1510‐0137
1510‐0138
1510‐0139
1510‐0140
1510‐0141
1510‐0142
1510‐0143
1510‐0144
1510‐0145
1510‐0146
1510‐0147
1510‐0148
1510‐0149
1510‐0150
1510‐0151
1510‐0152
1510‐0153
1510‐0154
Description
Flip up Bostrom ABTS attendant seat located [#LOC].
Bostrom SecureAll mechanical air pack bottle bracket (EA) for bench / fold‐down seat. Location: [#LOC].
Rear Seat Riser Storage. Includes smooth plate doors with push‐button latches on sides and front (access to battery charger). Side access is to SCBA storage (2) bottles. Bottles to be stored on plastic trays with vecro strapping to secure bottles with unit in motion. Side compartment openings to be 17" w x 10" h x 26" d. Front access to be a drop down door with push‐button latches. Riser and doors to be cab interior color.
Adjust rear facing outboard seats as far inboard as appicable next to engine cover.
Rear wall seat Bostrom air ride Sierra non SCBA. Includes single riser. N/A with outboard rear wall seats. Storage below seat N/A. Location: [#LOC].
Arm rest installed on both sides of the seat. Location: [#LOC].
Center rear wall seats to be mounted approximately 5" apart. C2X/T2X only.
Bostrom SCBA seat forward facing center of rear wall. Free standing mtd on seat riser.
Two man bench centered on rear wall with (1) 911 SCBA back driver and (1) bench back cushion officer.
Seating Package Two (2) Door Freightliner. Includes One (1) Seats Inc 911 Universal Hi‐Back Air Ride Driver and a Two (2) Person Bench Seat.
Universal 911 Seating Package. Includes one (1) hi‐back air ride suspension driver seat, one (1) hi‐back fixed SCBA officer seat, and three (3) fixed SCBA rear seats. Seats shall have NFPA 1901‐2009 compliant seat sensors.Tradition.
Seating Package Two (2) Door International. Includes One (1) National Brand air suspended driver seat and (1) National Brand air suspended officer seat.
Seating Package Two (2) Door International. Includes One (1) Gra‐Mag fixed driver seat and (1) Gra‐Mag fixed officer seat.
One (1) two person seating capacity tag‐ driver side area and two (2) seat belt warning tags‐ one (1) each cab door. For use with International chassis.
FlameFighter model 14000 air pack bottle bracket with model 39015 safety strap (EA). Location: [#LOC]
Seating Package Two (2) Door International 7600. Includes One (1) National Brand air suspended driver seat and (1) Gra‐Mag fixed officer seat.
911 AIR SCBA seats forward facing center of rear wall (PR). Free standing with individual risers on rear wall.
PRICE
$1,155.00
$695.00
911 SCBA seats forward facing rear wall (3). Equally spaced with common riser on rear wall. Extended cab with medium doors only.
Rear facing 911 attendant seat driver's side.
Rear facing 911 attendant seat officer's side.
Two man bench centered on rear wall with (1) Bostrom SCBA back officer and (1) bench back cushion driver.
Universal air pack bottle bracket installed (EA).
N/A ‐ Base extends to far rearward) Driver seat Bostrom mechanical with integral seat belt.
Bostrom SCBA seats forward facing center of rear wall (PR). Free standing mounted on a common seat riser.
Three man bench offset to driver on rear wall with Bostrom SCBA backs for use with ALS provision with officer side access only. Includes provision for rear heaters mounted below bench.
$3,354.00
$703.00
$703.00
$1,581.00
$163.00
$2,017.00
$2,142.00
$2,796.00
$126.00
$1,466.00
$535.00
$254.00
$1,131.00
$1,250.00
$0.00
$0.00
$363.00
$0.00
$0.00
$245.00
$0.00
$3,213.00
$2,781.00
Option No.
Description
PRICE
1510‐0155
Bostrom SCBA seats forward facing rear wall (3). Equally spaced with common riser on rear wall. Extended cab with medium doors only.
One (1) Bostrom (Non‐SCBA) driver seat, Durawear gray. Includes air ride suspension, occupant detection switches and E‐ONE logo. Custome ES.
Bostrom Fixed SCBA officer seat, Durawear gray. Includes occupant detection switches and E‐ONE logo. Custom ES.
$3,147.00
1510‐0156
1510‐0157
1510‐0158
1510‐0159
1510‐0160
1510‐0161
1510‐0162
1510‐0163
1510‐0164
1510‐0165
1510‐0166
1510‐0167
1510‐0168
1510‐0169
1510‐0170
1510‐0171
1510‐0172
1510‐0173
1510‐0174
1510‐0175
1510‐0176
Bostrom Fixed SCBA officer seat, Durawear gray. Includes SecureAll SCBA brkt, occupant detection switches and E‐ONE logo. Custom ES.
Bostrom fixed rearward facing SCBA seat, Durawear gray. Locate over driver side wheel well. Includes occupant detection switches and E‐
ONE logo. Custom ES.
Bostrom fixed rearward facing SCBA seat, Durawear gray. Locate over driver side wheel well. Includes SecureAll SCBA brkt, occupant detection switches and E‐ONE logo. Custom ES.
Bostrom fixed rearward facing SCBA seat, Durawear gray. Locate over officer side wheel well. Includes occupant detection switches and E‐ONE logo. Custom ES.
Bostrom fixed rearward facing SCBA seat, Durawear gray. Locate over officer side wheel well. Includes SecureAll SCBA brkt, occupant detection switches and E‐ONE logo. Custom ES.
Rear two (2) person bench seat, Durawear gray. Includes (2) Bostrom SCBA seat backs. Locate centered on rear cab wall. Includes occupant detection switches and E‐ONE logos. Custom ES.
Rear two (2) person bench seat, Durawear gray. Includes (2) Bostrom SCBA seat backs. Locate centered on rear cab wall. Includes SecureAll SCBA brkts, occupant detection switches and E‐ONE logos. Custom ES.
One seating capacity tag (3 person) to be installed visible by driver. Custom ES.
One seating capacity tag (4 person) to be installed visible by driver. Custom ES.
One seating capacity tag (5 person) to be installed visible by driver. Custom ES.
One seating capacity tag (6 person) to be installed visible by driver. Custom ES.
Universal air pack bottle bracket installed (EA). Commercial ES.
Universal air pack bottle bracket installed (EA). Custom ES.
Seating Package Two (2) Door Freightliner. Includes One (1) Talladega 910 Hi‐Back Air Ride Driver and One (1) 911 Fixed Officer (Non‐
SCBA).
Seating Package Two (2) Door Freightliner. Includes One (1) Talladega 905 Hi‐Back Air Ride Driver and a Two (2) Person Bench Seat.
Universal 911 Seating Package. Includes one (1) hi‐back air ride suspension driver seat, one (1) hi‐back fixed SCBA officer seat, and three (3) fixed SCBA rear seats.
Seating Package Four (4) Door Freightliner. Includes One (1) Talladega 910 Hi‐Back Air Ride Driver, Two (2) Person Bench Seat (front) and Three (3) Person Bench Seat (rear).
Universal 911 Seating Package. Includes one (1) hi‐back air ride suspension driver seat, one (1) hi‐back fixed SCBA officer seat, and three (3) fixed SCBA rear seats.
Universal 911 Seating Package. Includes one (1) hi‐back air ride suspension driver seat, one (1) hi‐back fixed SCBA officer seat, and three (3) fixed SCBA rear seats.
$0.00
$0.00
$440.00
$0.00
$580.00
$0.00
$580.00
$2,045.00
$3,266.00
$0.00
$0.00
$0.00
$0.00
$136.00
$136.00
$332.00
$0.00
$2,239.00
$0.00
$0.00
$0.00
Option No.
1510‐0177
1510‐0178
1510‐0179
1510‐0180
1510‐0181
1510‐0182
1510‐0183
1510‐0184
1510‐0185
1510‐0186
1510‐0190
1510‐0193
1510‐0197
1510‐0198
1510‐0199
1510‐0200
1510‐0203
1510‐0204
1510‐0205
1510‐0206
1510‐0207
1510‐0208
1510‐0209
1510‐0210
Description
Seating Package Two (2) Door International. Includes One (1) Nat'l Brand Air Ride Driver and Two (2) Person Bench Seat.
Seating Package Two (2) Door International. Includes One (1) Nat'l Brand Air Ride Driver and One (1) Nat'l Brand Air Ride Officer (Non‐
SCBA).
Seating Package Two (2) Door Freightliner. Includes One (1) Seats Inc 911 Universal Hi‐Back Air Ride Driver and a Two (2) Person Bench Seat.
One (1) two person seating capacity tag‐ driver side area and two (2) seat belt warning tags‐ one (1) each cab door. For use with International chassis.
One (1) three person seating capacity tag‐ driver side area and two (2) seat belt warning tags‐ one (1) each cab door. For use with International chassis.
One (1) five person seating capacity tag‐ driver side area and four (4) seat belt warning tags‐ one (1) each cab door. For use with International chassis.
One (1) three person seating capacity tag‐ driver side area and two (2) seat belt warning tags‐ one (1) each cab door. For use with Freightliner chassis.
One (1) five person seating capacity tag‐ driver side area and four (4) seat belt warning tags‐ one (1) each cab door. For use with Freightliner chassis.
Rear facing seat center rear engine cover Bostrom with SCBA back and integral seat belt.
Driver and officer outboard rear facing seats mounted at 10 degree inboard angle.
911 SCBA seats forward facing rear wall (3). Equally spaced with common riser on rear wall. Center seat lowered 4". For use with extended LTH aerial cab with medium doors only.
Seating Package Two (2) Door International. Includes one (1) 911 hi‐back air ride suspension driver seat and one (1) 911 hi‐back fixed SCBA officer seat.
CrewGuard occupant seating detection system. Display location: [#LOC].
Seating Package Two (2) Door International. Includes One (1) National Brand air suspended driver seat and (1) National Brand fixed officer seat.
Seating Package Two (2) Door International. Includes One (1) Nat'l Brand Air Ride Driver and One (1) Seats Inc. (Universal Series) high back fixed SCBA.
Department patch sewn on Bostrom seat (EA). Requires customer supplied department patch for each seat.
Bracket SCBA IMMI SmartDock Gen2 restraint system. Location: [#LOC].
Officer seat to be 911 electric SCBA
Officer SCBA release located on the inboard side of the seat.
Zico electric hands‐free air pack bottle bracket (EA). Model QM‐ELB with adjustable footplate. Bracket release will be activated with park brake. Location: [#LOC].
Riser to be 13" in height. Vista cabs only.
Seating Package Two (2) Door Freightliner. Includes One (1) 911 Universal brand high back air suspended driver seat and (1) 911 Universal brand air suspended officer seat. NFPA compliant seat sensors and wiring included in seats.
Driver seat to be 911 attendant. Includes forward and aft adjustment.
Two man bench centered on rear wall with bench style back cushion for use with ALS provision with side access only.
PRICE
$0.00
$121.00
$0.00
$0.00
$0.00
$0.00
$0.00
$0.00
$986.00
$519.00
$3,354.00
$472.00
$1,960.00
$420.00
$689.00
$114.00
$527.00
$2,098.00
$0.00
$765.00
$157.00
$363.00
$703.00
$1,835.00
PRICE
$1,970.00
$2,735.00
$157.00
$157.00
1510‐0230
1510‐0231
1510‐0232
Description
Driver seat to be Bostrom air ride with integral seat belt.
Officer seat to be Bostrom SCBA air ride with integral seat belt.
Rear wall seat riser to be 16" in height. Vista cabs only.
Rear wall seat riser to be raised 4" in height. Includes 2" bench seat cushion thickness reduction for non‐vista roofs.
One (1) two person seating capacity tag‐ driver side area and two (2) seat belt warning tags‐ one (1) each cab door. For use with Kenworth chassis.
Seating Package National brand for (2) Door Kenworth. Includes One (1) high back air suspended driver seat and (1) fixed officer seat with seat riser storage area. Seat color to be black and include NFPA compliant seat sensors and wiring.
Arm rest rear wall (PR). Located outboard of bench seat on seat support channel.
Seating Package Two (2) Door International. Includes One (1) 911 air ride driver seat and (1) 911 non‐suspended SCBA officer seat.
Navistar seat package, Wildland, Base, Air driver, Air passenger
Navistar seat package, Wildland, optional, Air driver, SCBA passenger.
Navistar seat package, Wildland, Base, Rear, Bench
Navistar seat package, Wildland, option, Rear, (2) SCBA
Seat package, Wildland, option, Rear, (3) SCBA
Bostrom seat package, Wildland, Option, Rear, (2) Hi‐Back
Seat base option Wildland, Option, Rear, (2) pull‐out trays
Officer seat to be Bostrom fixed attendant.
Zico Quic‐Hold mechanical air pack bottle bracket (EA). Model QM‐ROLO‐SA with adjustable footplate and pull release.
Three man bench center on rear wall with 911 SCBA backs. Includes provision for rear heaters mounted below bench (if equipped).
(2) Flip up Bostrom attendant seats with common riser located center on rear wall.
One (1) two person seating capacity tag‐ driver side area and two (2) seat belt warning tags‐ one (1) each cab door. For use with Freightliner chassis.
Seats to be provided with black seat belts in lieu of red.
Seat 911 Magnum 100 air ride. Location: driver and officer. NON‐NFPA compliant units only. No Logo.
1510‐0233
1510‐0234
Three man bench center on rear wall with Bostrom SCBA backs. Includes provision for rear heaters mounted below bench (if equipped).
Seat cover material Turnout Tuff.
$2,781.00
$0.00
1510‐0235
Two man bench centered on rear wall with Seats 911 SCBA backs for use with ALS provision. Includes recess for SCBA brackets in wall.
Seating Package Two (2) Door Freightliner. Includes One (1) 911 Universal brand high back air suspended driver seat and (1) 911 Universal brand high back air suspended officer seat. NFPA compliant seat sensors and wiring included in seats.
Seating Package Two (2) Door Freightliner. Includes One (1) Seats Inc 911 Universal Hi‐Back Air Ride Driver and One (1) 911 Fixed Officer (Non‐SCBA).
Bostrom SCBA seats with integral seat belt forward facing center of rear wall (PR). Free standing mounted on a common seat riser.
Universal 911 Seating Package. Includes one (1) hi‐back air ride suspension driver seat, one (1) hi‐back air ride suspension officer seat, and three (3) fixed SCBA rear seats.
$3,265.00
Option No.
1510‐0211
1510‐0212
1510‐0213
1510‐0214
1510‐0215
1510‐0216
1510‐0217
1510‐0218
1510‐0219
1510‐0220
1510‐0221
1510‐0222
1510‐0223
1510‐0224
1510‐0225
1510‐0226
1510‐0227
1510‐0228
1510‐0229
1510‐0236
1510‐0237
1510‐0238
1510‐0239
$0.00
$363.00
$451.00
$1,436.00
$0.00
$175.00
$0.00
$878.00
$1,274.00
$1,853.00
$4,508.00
$680.00
$524.00
$3,077.00
$2,471.00
$0.00
$0.00
$1,066.00
$363.00
$0.00
$2,334.00
$50.00
Option No.
1510‐0240
1510‐0241
1510‐0243
1510‐0244
1510‐0245
1510‐0246
1510‐0248
1510‐0249
1510‐0251
1510‐0252
1510‐0253
1510‐0254
1510‐0255
1510‐0256
1510‐0257
1510‐0258
1510‐0259
1510‐0260
1510‐0261
1510‐0262
1510‐0263
1510‐0264
1510‐0265
1510‐0266
Description
Driver, officer and rear bench seat riser constructed of diamond plated IPOS (as equipped). Includes diamond plate overlay for rear facing seats.
Driver and officer's seat riser constructed of diamond plated IPOS (as equipped).
Two (2) Bostrom SCBA seat backs and a three (3) person bench (no center position).
Driver seat Bostrom electric with SCBA back with integral seat belt.
Universal 911 Seating Package. Includes one (1) hi‐back air ride suspension driver seat, one (1) hi‐back air ride suspension SCBA officer seat, and two (2) fixed SCBA rear seats.
One (1) four person seating capacity tag‐ driver side area and four (4) seat belt warning tags‐ one (1) each cab door. For use with Freightliner chassis.
Seats Inc 911 SCBA seat forward facing rear wall center. For use with extended cab with side access ALS compartments. Includes pass‐
thru and rear heater provision (if equipped).
Two man bench centered on rear wall with Bostrom SCBA backs for use with ALS provision with side access only or interior side compartments. Includes provision for rear heaters mounted below bench.
Flamefighter SCBA seats forward facing center of rear wall (PR). Free standing mounted on a common seat riser.
Location modification of electric seat controls. The controls shall be relocated to the outboard side of the seat as mounted IPO standard location.
Bostrom SecureAll mechanical air pack bottle bracket (EA). SecureAll factory adjusted to accommodate carbon fiber bottle(s) in mounted location(s) as specified. Location: [#LOC].
Bostrom SecureAll mechanical air pack bottle bracket (EA) for bench / fold‐down seat. SecureAll factory adjusted to accommodate carbon fiber bottle(s) in mounted location(s) as specified. Location: [#LOC].
Back cushion for a folding jump seat. The rear cushion shall be located: [#LOC].
Two man bench centered on rear wall Non‐SCBA seat backs. (1) Access door on each side/end of riser to store (1) SCBA bottle on each side of riser.
Rear facing and forward facng rear cab risers to be extended 2" in height. Vista cabs only.
Zico EZ‐LOC mechanical air pack bottle bracket (EA). Model QM‐EZL with adjustable top clamp and footplate with center pull release for Bostrom seat. Location: [#LOC].
Driver and officer outboard rear facing seats mounted at 15 degree inboard angle.
Cargo net covers for sides of seat riser IPOS.
911 Attendant seat (PR) on common riser. Locate centered on rear wall.
Universal 911 Seating Package. Includes one (1) hi‐back air ride suspension driver seat, one (1) hi‐back fixed SCBA officer seat, and three (3) fixed SCBA rear seats. Seats shall have NFPA 1901‐2009 compliant seat sensors. Tradition.
Two man bench centered on rear wall with 911 SCBA backs. Includes square corners.
Two man bench centered on rear wall with Bostrom SCBA. Includes square corners.
Department patch sewn on 911 seat (EA). Requires customer supplied department patch for each seat.
Seat 911 Magnum 100 air ride forward facing center of rear wall (PR). Free standing mtd on a common seat riser. NON‐NFPA compliant units only. No Logo.
PRICE
$351.00
$127.00
$2,268.00
$2,113.00
$2,239.00
$0.00
$1,146.00
$2,217.00
$3,920.00
$226.00
$567.00
$695.00
$235.00
$1,725.00
$499.00
$627.00
$519.00
$178.00
$2,393.00
$0.00
$1,423.00
$1,754.00
$114.00
$2,131.00
Option No.
1510‐0267
1510‐0268
1510‐0269
1510‐0270
1510‐0271
1510‐0272
1510‐0273
1510‐0274
1510‐0275
1510‐0276
1510‐0277
1510‐0278
1510‐0279
1510‐0280
1510‐0281
1510‐0282
1510‐0283
1510‐0284
1510‐0285
1510‐0286
1510‐0287
1510‐0288
1510‐0289
1510‐0290
1510‐0291
1510‐0292
1510‐0300
1510‐0301
1510‐0302
1510‐0303
1510‐0304
1510‐0305
1510‐0306
Description
Two man bench centered on rear wall with Bostrom SCBA backs includes squared corners and separate seat bottoms spaced 6" from each other.
Rear facing seat center rear engine cover Bostrom flip‐up with SCBA back and integral seat belt.
There shall be no E‐One logos on cab seats.
Seatbelt P‐clips. Provide on all connector ends of seatbelts.
Seating Package Two (2) Door International. Includes One (1) National Brand air suspended driver seat and (1) National Brand standard suspension officer seat.
Driver seat to be Bostrom fixed SCBA. Includes fore and aft adjustment.
Four man bench centered on rear wall with (2) Bostrom SCBA inboard and attendant backs outboard.
Two man bench centered on rear wall with 911 SCBA backs for use with exterior side access only or interior side compartments. Includes provision for rear heaters mounted below bench.
Arm rest installed on the outboard side of the seat. Location: [#LOC].
Face mask storage pouch for Bostom Tanker series SCBA seats (EA).
Driver outboard rear facing seat mounted at 10 degree inboard angle.
Two man bench centered on rear wall with bench style back cushion with 2" extra depth removable bottom cushion with cut‐out under cushion and angle corners for use with ALS provision with side access only.
ReadyReach seat belt extender. Location: [#LOC].
Rear facing seat driver side rear engine cover Bostrom with SCBA back and integral seat belt.
Driver seat 911Battalion air ride ABTS.
Officer seat 911 Battalion ABTS air ride SCBA. N/A with Roll‐Tek or 4Front due to reduction in legroom caused by pre‐tensioner.
Officer seat to be 911 Battalion ABTS fixed SCBA.
Rear facing 911 Battalion ABTS seat with SCBA driver's side.
Rear facing 911 Battalion ABTS seat with SCBA officer's side.
Two man bench centered on rear wall with 911 Battalion ABTS SCBA backs. Includes angled corners.
Two man bench centered on rear wall with 911 Battalion ABTS SCBA backs. Includes square corners.
Flip‐up 911 Battalion ABTS SCBA seat located [#LOC].
Fold down seat with 911 Battalion ABTS SCBA back located [#LOC].
Rear facing 911 Battalion ABTS seat with SCBA on engine cover.
Arm rest installed on the inboard side of the seat. Location: [#LOC].
Flip‐up 911 SCBA seats forward facing center of rear wall (PR). Free standing mtd on a common seat riser.
Heated seat. The seat shall include a switch that shall be easily accessible from the seated position. Location: [#LOC]
Seats, Valor brand.
Seat cover material Valor Tech XD (previously identified as Cordura).
Seat color black with red stitching.
Seats to be 18" wide.
Seats to be 20" wide.
Driver seat USSC Valor air ride ABTS.
PRICE
$1,878.00
$1,248.00
$0.00
$202.00
$138.00
$1,171.00
$2,864.00
$2,513.00
$270.00
$96.00
$260.00
$2,741.00
$89.00
$986.00
$2,356.00
$2,103.00
$1,096.00
$1,096.00
$1,096.00
$2,212.00
$2,212.00
$1,252.00
$1,152.00
$1,096.00
$270.00
$2,036.00
$169.00
$0.00
$0.00
$0.00
$0.00
$0.00
$2,503.00
Option No.
1510‐0307
1510‐0308
1510‐0309
1510‐0310
1510‐0314
1510‐0315
1510‐0316
1510‐0317
1510‐0318
1510‐0319
1510‐0320
1510‐0321
1510‐0322
1510‐0323
1510‐0324
1510‐0325
1510‐0326
1510‐0327
1510‐0328
1510‐0329
1510‐0330
1510‐0331
1510‐0332
1510‐0333
1510‐0334
1510‐0335
1510‐0336
1510‐0337
1510‐0338
Description
Officer seat USSC Valor ABTS fixed SCBA. Includes fore and aft slides.
Rear facing USSC Valor ABTS seat with SCBA driver's side.
Rear facing USSC Valor ABTS seat with SCBA officer's side.
Dynamic adjustable SCBA cavity (ea). Valor seats only.
Flip‐up USSC Valor ABTS SCBA seat (3). Locate in crew compartment equally spaced. Outboard seats to be approx 29" from center seat (center to center).
Flip‐up USSC Valor ABTS SCBA seat (4). Locate in crew compartment equally spaced.
Two man SCBA bench seat riser only with angled corners. No SCBA backs or bottom cushion. For lower storage only.
**OBS** (use 1510‐0258‐XXX instead) Zico EZ‐LOC mechanical air pack bottle bracket (EA). Model QM‐EZL‐CPR with adjustable top clamp and adjustable footplate with center pull release for 911 seats. Location: [#LOC].
Rear facing Bostrom seat fixed attendant officer's side.
(2) Flip up Bostrom SCBA seats with common riser located center on rear wall.
Rear facing USSC Valor ABTS seat with SCBA driver's side. Includes fore and aft slides.
Rear facing USSC Valor ABTS seat with SCBA officer's side. Includes fore and aft slides.
Flip‐up USSC Valor ABTS seat with 90 deg SCBA back (PR) forward facing center of rear wall mounted on a common seat riser. Long cab with medium doors only.
Adjustable forward/aft seat track on officer seat.
Officer seat USSC Valor air ride ABTS SCBA. Includes fore and aft slides.
Flip‐up USSC Valor ABTS seats forward facing center of rear wall mounted on a common seat riser. Includes (1) SCBA (driver side) and (1) non‐SCBA (officer side) forward facing center of rear wall mounted on a common seat riser.
Zico EZ‐LOC mechanical air pack bottle bracket (EA). Model QM‐EZL with adjustable top clamp and adjustable footplate with center pull release for Valor seats. Location: [#LOC].
Custom logo embroidery (EA). Valor seats only.
Driver seat USSC Valor air ride.
Officer seat USSC Valor fixed SCBA.
Rear facing USSC Valor SCBA seat driver's side.
Rear facing USSC Valor SCBA seat officer's side.
Two man bench centered on rear wall with Valor SCBA backs. Includes angled corners.
Two man bench centered on rear wall with Valor SCBA backs. Includes square corners.
Seat color black and red with red stitching.
Fold down seat with Bostrom SCBA back and Bostrom bottom cushion. Not available at outboard position w/manual windows. Located [#LOC].
Bostrom SecureAll pull handles in bottom cushions. Locations: Officer seat, driver rear facing seat, officer rear facing seat, rear 2‐man bench seat.
Universal air pack bottle bracket (EA). Ziamatic KD‐ULLH‐EZO Universal SCBA E‐Z Out bottle bracket(s) shall be mounted in place. Location : [#LOC].
Rear facing cab risers to be extended 3" in height. Vista cabs only.
PRICE
$1,409.00
$1,181.00
$1,181.00
$363.00
$4,076.00
$5,435.00
$1,224.00
$708.00
$680.00
$2,591.00
$1,409.00
$1,449.00
$3,251.00
$98.00
$2,351.00
$3,515.00
$690.00
$99.00
$1,855.00
$998.00
$1,080.00
$1,080.00
$2,201.00
$2,346.00
$0.00
$1,035.00
$1,788.00
$195.00
$209.00
Option No.
1510‐0339
1510‐0340
1510‐0341
1510‐0342
1510‐0343
1510‐0344
1510‐0345
1510‐0346
1510‐0347
1510‐0349
1510‐0350
1510‐0351
1510‐0352
1510‐0353
1510‐0354
1510‐0355
1510‐0356
1510‐0357
1510‐0358
1510‐0359
1510‐0360
1510‐0361
1510‐0362
1510‐0363
1510‐0364
1510‐0365
1510‐0366
1510‐0367
1510‐0368
1510‐0369
1510‐0370
Description
Bostrom attendant seats with integral seat belt forward facing center of rear wall (PR). Free standing mounted on a common riser.
Officer seat USSC Valor ABTS fixed SCBA.
Engine cover USSC Valor two man bench with SCBA.
Dynamic adjustable SCBA cavity (ea). Valor seats only. Location: [#LOC].
Flip‐up USSC Valor ABTS seat with 90 deg SCBA back (3) forward facing equally spaced on rear wall mounted on a common seat riser. Long cab with medium doors only.
Driver seat USSC Valor air ride ABTS with R style back.
Officer seat USSC Valor air ride SCBA.
Zico model ULLH‐EZO air pack bottle bracket (EA). Location: [#LOC].
Rear walll 4 man seat riser. Includes 2 man bench centered on rear wall with Bostrom SCBA and outboard flip up Bostrom SCBA seat each side of bench. 80" C/A cabs only.
Fold‐down rear wall seat with 12.25" long Bostrom bottom cushion. Includes E‐ONE non‐SCBA backrest. Seat located [#LOC].
One man bench inboard driver side on rear wall with 911 SCBA.
(3) Flip up Bostrom SCBA seats with integral seat belt and common riser located evenly spaced on rear wall.
(2) individual Bostrom ABTS SCBA seats outboard on a common 60" wide riser. Includes provision for rear heaters mounted below bench (if equipped).
Driver seat Bostrom electric with integral dual retractor seat belt.
Officer seat fixed Bostrom 550 with SCBA back and integral dual retractor seat belt.
Rear facing seat officer side Bostrom 550 with SCBA back and integral dual retractor seat belt.
Bostrom 550 SCBA seats with integral dual retractor seat belt forward facing center of rear wall (PR). Free standing mounted on a common seat riser.
Driver seat to be 911 Battalion electric ABTS.
Flip‐up 911 Battalion ABTS SCBA seat located rear engine cover (PR). Vista cabs only.
Two man bench centered on rear wall with (1) 911 SCBA back center on rear wall.
Rear facing Bostrom seat fixed attendant driver's side.
Rear facing seat driver side Bostrom attendant with integral seat belt.
Rear facing seat officer side Bostrom attendant with integral seat belt.
Two (2) Bostrom SCBA seat backs on a three (3) person bench riser (no center position) with individual bottom cusions.
Officer seat fixed Bostrom attendent with integral seat belt.
Officer seat USSC Valor air ride.
Fold‐down rear wall seat with Valor bottom cushion. Includes E‐ONE non‐SCBA backrest. Seat located [#LOC].
One (1) two person seating capacity tag‐ driver side area and two (2) seat belt warning tags‐ one (1) each cab door. For use with Commercial chassis.
Officer seat USSC Valor non‐SCBA fixed with recline back.
Locate officer's seat as far rearward as possible.
Fold‐down rear wall jump seat to be mounted 2.75" lower than std to provide additional headroom (EA). Non‐SCBA seats only. (Not available with heaters mounted outboard on rear wall)
PRICE
$2,334.00
$1,181.00
$3,067.00
$363.00
$4,699.00
$2,503.00
$1,929.00
$323.00
$3,855.00
$912.00
$1,157.00
$3,887.00
$2,584.00
$2,122.00
$1,248.00
$1,248.00
$3,031.00
$2,791.00
$2,854.00
$1,250.00
$680.00
$983.00
$983.00
$2,268.00
$983.00
$1,855.00
$939.00
$0.00
$1,516.00
$0.00
$197.00
Option No.
1510‐0371
1510‐0372
1510‐0373
1510‐0374
1510‐0375
1510‐0376
1510‐0377
1510‐0378
1510‐0379
1510‐0380
1510‐0381
1510‐0382
1510‐0383
1510‐0384
1510‐0385
1510‐0386
1510‐0387
1515‐0000
1515‐0001
1515‐0002
1515‐0003
1515‐0004
1515‐0005
1515‐0006
1515‐0007
1515‐0012
1515‐0017
1515‐0018
1515‐0019
1515‐0020
1515‐0021
1515‐0023
1515‐0027
Description
Bench seat to have Valor supplied bottom cushion.
Fold‐down rear wall seat with Valor bottom cushion. Includes E‐ONE lumbar backrest. Seat located [#LOC].
Officer seat USSC Valor ABTS fixed attendant.
Officer seat to be Bostrom electric SCBA.
Rear facing seat driver side Bostrom 550 with SCBA back and integral dual retractor seat belt.
Rear wall seat Bostrom 500CT flip‐up with SCBA back and integral dual retractor seat belt. Location: [#LOC].
Two man bench riser centered on rear wall with (1) Bostrom SCBA back officer with single bottom cushion. Driver side open for dealer/customer installed equiipment.
Rear wall seat Bostrom 500CT flip‐up with SCBA back and integral dual retractor seat belt. Rear facing engine cover.
Officer seat Bostrom 550 electric with SCBA back with integral dual retractor seat belt.
Officer seat USSC Valor fixed SCBA with adjustable fore/aft track.
Rear facing USSC Valor SCBA seat driver's side with adjustable fore/aft track.
Rear facing USSC Valor SCBA seat officer's side with adjustable fore/aft track.
Fold down 911 Battalion ABTS SCBA seat located rear engine cover (PR). NON‐Vista cabs only.
Officer seat to be 911 Battalion ABTS fixed attendant.
Officer seat 911Battalion air ride ABTS.
Seat cover material Durawear Plus with low seams. Available in black only.
Rear wall seat Bostrom 500CT flip‐up with fold and hold seat bottom, SCBA back and integral dual retractor seat belt. Location: [#LOC].
Air conditioning aerial ISM/S60. Two roof top condensers, for use with aerials
Air Conditioning premium aerial ISM/S60. Two roof top condensers, for use with aerials
Air Conditioning ISC/ISL. Radiator mounted condenser
Air conditioning premium ISC/ISL. Radiator mounted condenser
Air Conditioning ISM/S60. Single roof top mounted condenser.
Air Conditioning premium ISM/S60. Single roof top mounted condenser
Air Conditioning filter kit
Air conditioning for Typhoon only
Paint air conditioning condenser job color.
Air conditioning for the Typhoon X, CII X and Quest with Cummins ISC/ISL engine and radiator mounted condenser.
Air conditioning for the Typhoon X, CII X and Quest with roof top mounted condenser.
Air Conditioning lines and fittings wrapped
Well nut fasteners to attach A/C filter to overhead panel
The AC lines to be wrapped and routed from any sharp edges.
A/C Cutoff Switch. Install switch in cab dash to turn off A/C in rear crew area.
Danhard cooling system for cab medical cabinet. 115v / 12v 13,500 BTU wired to battery charger recept. Includes auto transfer switch and IOTA 75A converter mounted on permanent shelf above breaker box in L1 compt. Evaporator to be cabimet mtd, condensor to be roof mtd and compressor to be frame mtd. Note: System draws up to 12 amps AC.
PRICE
$0.00
$939.00
$1,626.00
$2,094.00
$1,248.00
$2,028.00
$1,381.00
$2,028.00
$2,461.00
$1,226.00
$1,308.00
$1,308.00
$2,854.00
$1,036.00
$2,356.00
$56.00
$2,133.00
$7,608.00
$10,025.00
$6,508.00
$8,494.00
$6,761.00
$9,111.00
$280.00
$7,271.00
$849.00
$7,060.00
$8,246.00
$445.00
$258.00
$0.00
$65.00
$6,522.00
Option No.
1515‐0028
1515‐0029
1515‐0030
1515‐0031
1515‐0032
1515‐0033
1515‐0034
1515‐0035
1515‐0036
1515‐0037
1515‐0038
1515‐0040
1515‐0041
1515‐0042
1515‐0043
1515‐0044
1515‐0045
1515‐0046
1515‐0048
1515‐0049
1515‐0052
1515‐0053
1515‐0054
1515‐0055
1515‐0056
Description
Danhard cooling system for cab medical cabinet. 115v / 12v 13,500 BTU wired to battery charger recept. Includes auto transfer switch. Evaporator to be cabinet mtd and condensor to be roof mtd. Note: System draws up to 12 amps AC.
Air conditioning for the TyphoonX, CII X and Quest with Cummins ISC or ISL, roof top mounted condensor.
The cab A/C compressor drive to be a "V" belt with a 1.5:1 ratio.
Roof mtd A/C system Penguin 13,500 BTU. Locate on cab roof wired to shore power. Includes auto transfer switch.
Cab air conditioning for use with ISC or ISL engines. Custom ES.
Cab air conditioning for use with ISC or ISL engines. Includes front and rear floor heaters with diamond plate covers on rear units. Custom
ES.
PRICE
Roof mtd A/C system Coleman 13,500 BTU. Locate on rear cab roof wired to shore power and (if equipped w/auto transfer) generator.
Stainless steel pan for cab roof mounted A/C unit. Includes drain line to rear of cab. Drain not to drip on drivelines.
Danhard cooling system. 115v / 12v 13,500 BTU wired to battery charger recept. Includes evaporator enclosure on ceiling centered rear of cab AC. Compressor located on rear engine cover with expanded metal cover painted to match cab interior. Condensor to be officer side roof mounted above canopy area. Note: System draws up to 12 amps AC.
Locate roof mountd AC condensor offset to officer side.
Air hose routed from the compressor to the dryer shall be upgraded to include stainless steel mesh for the full length of hose.
Heating and air conditioning cab controls shall be located in the lower center dash panel between driver and officer.
Locate Danhard AC compressor offset to officer side next to rear facing seat on rear engine cover.
Defrost only for the cab heating system includes controls within the cab.
Roof mtd A/C system Penguin 13,500 BTU. Locate on driver side rear cab vista roof wired to shoreline.
Roof mtd A/C system Penguin 13,500 BTU. Locate on officer side rear cab vista roof wired to generator.
Controls for heating and air conditioning shall be located in the center dash area upper tier offset to driver side. For use with severe duty dash only.
Locate roof mounted AC condenser on [#LOC].
Controls for heating and air conditioning shall be located in the driver side lower dash area. For use without front air bags only.
Roof mtd A/C system Penguin II 13,500 BTU with 5600 BTU heat strips. Locate on cab roof wired to shore power. Locate control head in center overhead console offset to driver side.
Controls for heating and air conditioning shall be located in the center dash area upper tier. For use with severe duty dash only.
$2,096.00
$684.00
Controls for heating and air conditioning shall be located in the center dash area. (Lower area on Typhoon and CII with severe duty dash)
Controls for heating and air conditioning shall be located in the center dash area low and offset to driver side. For use with QST2 and HS products only.
Roof mtd A/C system Penguin 13,500 BTU. Includes: auto transfer switch and a dedicated auto‐eject with "Yellow "cover. The outer housing cover for the A/C unit to be painted Black. Locate: on body module rehab roof includes wiring to shore power connection at cab door.
Roof mtd A/C system Coleman Mach 8 15,000 BTU. Locate on rear cab roof wired to shore power and (if equipped w/auto transfer) generator.
$6,317.00
$8,246.00
$2,737.00
$3,763.00
$0.00
$2,046.00
$6,317.00
$0.00
$85.00
$520.00
$0.00
$0.00
$3,763.00
$3,763.00
$0.00
$595.00
$0.00
$3,838.00
$0.00
$0.00
$0.00
$4,659.00
$3,346.00
Option No.
1515‐0057
1515‐0058
1515‐0059
1515‐0061
1515‐0062
1515‐0063
1515‐0064
1515‐0065
1515‐0066
1515‐0067
1515‐0068
1515‐0069
1515‐0070
1515‐0071
1515‐0072
1515‐0073
1515‐0074
1515‐0075
1515‐0076
1515‐0077
1520‐0000
1520‐0001
1520‐0002
Description
Two (2) 21,000 BTU heaters shall be installed, One (1) in each step well of the TME module.
A Red Dot model# 9777 roof mounted air‐conditioner and heater shall be installed on top of the TME module. 25,000 BTU's cooling and 45,000 BTU's heat.
A remote mount filter and booster blower shall be located in the [#LOC] and be plumbed to the TME pump module roof mounted HVAC unit.
Roof mtd A/C system Penguin 13,500 BTU w/ 5600 BTU heat. Includes: auto transfer switch and a dedicated auto‐eject with "Yellow "cover. The outer housing cover for the A/C unit to be painted Black. Locate: on body module rehab roof includes wiring to shore power connection at cab door.
Roof mtd A/C system Penguin II 13,500 BTU with 5600 BTU heat strips. Wire to shore power (includes auto transfer switch). Locate A/C Unit on cab roof.
Controls for heating and air conditioning shall be located in the center dash area upper tier offset to officer side. For use with severe duty dash only.
Locate rear cab heaters one each side below rear wall seats.
A Red Dot model# 9777 roof mounted air‐conditioner and heater shall be installed on top of the walk in rescue body. 25,000 BTU's cooling and 45,000 BTU's heat. 12VDC system R134A plumbed to existing chassis AC compressor for a split system. The heating unit shall be piped to the chassis radiator/cooling system with silicone heater hose. The heating system shall be equipped with shut‐off valves at the engine area connection.
Roof mtd A/C system Dometic BliZZard Self‐Contained HVAC Series SC14K 14,000 BTU with heat strips. Wire to APU/Generator. Locate condenser unit on officer side of cab roof. Location of interior evaporator: [#LOC].
Locate rear cab heaters outboard each side above seat support channel.
Roof mtd A/C system Dometic BliZZard Self‐Contained HVAC Series SC14K 14,000 BTU. Wire to shorepower and generator (if equipped with transfer switch). Locate condenser unit on officer side of cab roof. Location [#LOC].
Heaters cab rear (PR), and front heater with heat to the feet for the driver and officer. Driver side rear wall w/cover only.
Air conditioning for HS cab with Cummins ISL engine. Includes center front cab evaporator and roof top mounted condenser.
Locate roof mountd AC condensor offset to driver side (same as location as rear mount aerial).
Roof mtd A/C system Dometic BliZZard Self‐Contained HVAC Series SC14K 14,000 BTU. Wire to APU. Locate condenser unit on officer side of cab roof. Location of interior evaporator: rear engine cover.
Roof mtd A/C system Penguin II 13,500 BTU. Wire to APU only. Locate A/C Unit on cab roof.
Roof mtd A/C system Dometic BliZZard Self‐Contained HVAC Series SC14K 14,000 BTU. Wire to shoreline receptacle. Locate condenser unit on officer side of cab roof. Location of interior evaporator: [#LOC].
Defroster system with ceiling mounted heater.
Heater rear cab w/o cover (EA) and front cab heater with heat to the feet for the driver and officer. Rear heater located under driver side of bench seat.
Additional control for rear facing air conditioner. Locate adjacent to rear AC vents/filter.
Cyclone II medium cab 58" CA
Cyclone II long cab 67.5" CA
Cyclone II extended cab 80" CA
PRICE
$1,922.00
$3,004.00
$661.00
$4,741.00
$3,362.00
$0.00
$0.00
$3,556.00
$4,909.00
$397.00
$4,909.00
$1,676.00
$8,246.00
$0.00
$4,909.00
$3,362.00
$4,909.00
$0.00
$1,233.00
$498.00
$59,338.00
$65,553.00
$66,229.00
Option No.
1520‐0003
1520‐0004
1520‐0005
1520‐0006
1520‐0007
1520‐0008
1520‐0009
1520‐0010
1520‐0011
1520‐0012
1520‐0013
1520‐0014
1520‐0015
1520‐0017
1520‐0018
1520‐0019
1520‐0020
1520‐0021
1520‐0022
1520‐0023
1520‐0024
1520‐0025
1520‐0026
1520‐0027
1520‐0028
1520‐0029
1520‐0030
1520‐0031
1520‐0032
1520‐0033
1520‐0036
1520‐0037
1520‐0038
1520‐0071
1520‐0076
Description
Typhoon long cab 67.5" CA
Typhoon Medium cab 58" CA
Cyclone II medium cab three door with rear door on officer's side.
Cyclone II long cab three door with rear door on officer's side.
Tillerman cab. Heat & A/C and (3) 6" (12VDC) fans ceiling mounted, (1) each rear corner & (1) front left corner. Seat material and color is the same as in the front cab.
Cyclone II X medium cab with 58" CA
Cyclone II X short cab with 44.5" CA
Cyclone II X long cab with 67.5" CA
Cyclone II X extended cab with 80" CA
Typhoon X long cab with 67.5" CA
Typhoon X medium cab with 58" CA
Cyclone II X medium cab with 58" CA. Includes barrier style doors. Orange County, California. Includes mounting on engine cover of customer supplied computer bracket (see engineering), cut‐out in driver side overhead for customer supplied radio.
Cyclone II X medium cab with ALS provision and 80" CA. Includes exterior hinged ALS doors approx 73" high.
Quest long cab with 68" CA
Quest medium cab with 58" CA
Cyclone II X medium cab with ALS provision, barrier style doors and 80" CA. Includes exterior hinged ALS doors approx 73" high.
Quest medium cab with 58" CA and barrier style doors.
Typhoon X long cab with 67.5" CA. Includes barrier style doors.
Cyclone II X medium cab with 58'' CA. Includes barrier style doors.
Cyclone II X long cab with 67.5" CA. Includes barrier style doors.
Cyclone II X extended cab with 80" CA. Includes barrier style doors.
Typhoon X medium cab with 58" CA. Includes barrier style doors.
Quest long cab with 68" CA and barrier style doors.
Quest extended cab with 80" CA.
Cyclone II X long cab with 67.5" CA. For use with a lowered aerial. Requires full length 4.5" deep trough option.
Typhoon X short cab with 44.5" CA
Cyclone II X Hush/Mid‐Engine long cab with 67.5" C/A
Cyclone II X Hush/Mid‐Engine medium cab with 58" C/A.
Cyclone II X Hush/Mid‐Engine medium cab with 58" C/A. Includes barrier style doors.
Cyclone II X Hush/Mid‐Engine long cab with 67.5" C/A. Includes barrier style doors.
Cyclone II X (2) door long cab with 67.5" C/A.
Cyclone II X 3DR Long cab with 67.5" CA. Includes barrier style doors.
Cyclone II X extended cab with 80" CA. For use with a lowered aerial. Requires full length 4.5" deep trough option.
Cyclone II X medium cab with 58" CA. For use with a lowered aerial. Requires full length 4.5" deep trough option.
Cyclone II X short cab with 30" CA. 2 door cab with barrier style doors and rear transverse compartment.
PRICE
$39,874.00
$37,171.00
$59,338.00
$65,553.00
$48,137.00
$57,211.00
$61,276.00
$63,428.00
$64,104.00
$37,746.00
$35,045.00
$65,137.00
$65,665.00
$63,428.00
$57,211.00
$66,491.00
$58,038.00
$38,576.00
$58,038.00
$64,257.00
$64,930.00
$35,885.00
$64,257.00
$64,104.00
$71,765.00
$39,111.00
$62,297.00
$56,081.00
$56,895.00
$63,126.00
$64,104.00
$64,257.00
$68,701.00
$61,808.00
$59,241.00
Option No.
1520‐0081
1520‐0087
1520‐0090
1520‐0092
1520‐0095
1520‐0096
1520‐0097
1520‐0098
1520‐0104
1520‐0105
1520‐0106
1520‐0107
1520‐0108
1520‐0109
1520‐0110
1520‐0111
1520‐0114
1520‐0115
1520‐0116
1520‐0118
1520‐0119
1520‐0122
1520‐0125
1520‐0126
1520‐0127
1520‐0128
1520‐0129
1520‐0130
1520‐0131
1520‐0142
1520‐0159
1535‐0002
Description
Cyclone II X short cab with 44.5" CA and right hand drive.
Cyclone II X short cab 2 door with 44.5" ca. Includes transverse compartment at rear of cab above the front axle accessible from both sides. The compartment is approx 48.5" wide x 44.25" high x the width of the cab.
Cyclone II X (3) door extended cab with 80" CA. Officer side rear door.
Cyclone II X medium cab with 58'' CA. Includes barrier style doors. For use with a lowered aerial. Requires full length 4.5" deep trough option.
Cyclone II X long cab with 67.5" CA and barrier style doors. For use with a lowered aerial. Requires full length 4.5" deep trough option.
Typhoon X extended cab with 80" CA
Typhoon X extended cab with 80" CA. Includes barrier style doors.
Quest (3) door extended cab with 80" CA and barrier style doors. Officer side rear door.
Cyclone II X (3) door extended cab with 80" CA. Includes barrier style doors. Locate rear door on Officer side of cab.
Upgrade rear cab subframe with solid billet aluminum inserts. Severe duty 80" cab only.
Quest medium cab with 58" CA. (QST2)
Quest long cab with 68" CA. (QST2)
Quest extended cab with 80" CA. (QST2)
Quest medium cab with 58" CA and barrier style doors. (QST2)
Quest long cab with 68" CA and barrier style doors. (QST2)
Quest extended cab with 80" CA and barrier style doors. (QST2)
Typhoon X medium cab with ALS provision, barrier style doors and 80" CA. Includes exterior hinged ALS doors approx 73" high.
Quest medium cab with ALS provision and 80" CA (QST2). Includes exterior hinged ALS doors approx 73" high.
Quest medium cab with ALS provision, barrier style doors and 80" CA (QST2). Includes exterior hinged ALS doors approx 73" high.
Quest HS medium cab with 58" CA.
Cyclone HS medium cab with 58" C/A. Includes barrier style doors.
Typhoon X medium cab with ALS provision and 80" CA. Includes exterior hinged ALS doors approx 73" high.
Cyclone HS medium cab with 58" C/A.
Cyclone HS long cab with 67.5" C/A. Includes barrier style doors.
Cyclone HS long cab with 67.5" C/A.
Quest HS medium cab with 58" CA and barrier style doors.
Quest HS long cab with 68" CA.
Quest HS long cab with 68" CA and barrier style doors.
Typhoon X short cab with 44.5" CA with barrier style doors.
Cyclone II X short cab 2 door with 44.5" ca with barrier style doors. Includes transverse compartment at rear of cab above the front axle accessible from both sides. The compartment is approx 35.5" wide x 36" high x the width of the cab.
Cyclone II X (3) door medium cab with 58" CA. Officer side rear door.
Driver side cab wheel well medical cabinet approximately 42 x 22 (25 Quest) x 28. Includes external locking roll‐up door and interior hinged door with locking push‐button latch. Cabinet includes (2) adjustable shelves.
PRICE
$76,814.00
$61,276.00
$64,104.00
$62,635.00
$72,595.00
$41,938.00
$42,768.00
$64,817.00
$66,227.00
$840.00
$70,065.00
$76,282.00
$76,958.00
$70,892.00
$77,111.00
$77,784.00
$44,328.00
$78,519.00
$79,346.00
$69,012.00
$56,895.00
$43,502.00
$56,068.00
$63,114.00
$62,285.00
$69,839.00
$75,229.00
$76,058.00
$39,938.00
$61,626.00
$57,211.00
$2,179.00
Option No.
1535‐0003
1535‐0004
1535‐0005
1535‐0006
1535‐0007
1535‐0012
1535‐0013
1535‐0026
1535‐0027
1535‐0028
1535‐0029
1535‐0030
1535‐0031
1535‐0032
1535‐0033
1535‐0034
1535‐0035
1535‐0037
1535‐0038
1535‐0039
1535‐0040
1535‐0043
1535‐0044
Description
Officer side cab wheel well medical cabinet approximately 42 x 22 (25 Quest) x 28. Includes external locking roll‐up door and interior hinged door with locking push‐button latch. Cabinet includes (2) adjustable shelves.
Medical cabinet mounted on rear wall of cab 48 x 32 x 24 with a locking roll up door. Lower door opening raised to provide hand clearance.
Medical cabinet mounted on rear wall of cab 48 x 40 x 20 with locking roll up door. Lower door opening raised to provide hand clearance.
Medical cabinet mounted on rear wall of cab 55X32X19 with a locking roll up door. Lower door opening raised to provide hand clearance.
Medical cabinet mounted on rear wall of cab 55 x 40 x 20 with a locking roll up door. Lower door opening raised to provide hand clearance.
Medical cabinet mounted on the wheel well driver side of cab 45H x 21W x 24D with a locking roll‐up door.
Medical cabinet mounted on the wheel well officer side of cab 45H x 21W x 24D with a locking roll‐up door.
Cab medical storage cabinet(s) finish to be OTO gray.
Cab medical/storage cabinet(s) finish to be Zolatone gray. Exterior of bolt‐in cabinets; interior and exterior of weld‐in cabinets.
Cab medical storage cabinet(s) finish to be swirled with clear coating.
All medical cabinet doors within the cab to be POK brand
All roll‐up medical cabinet doors selected on the cab to be ROM brand.
All medical cabinet RUD in the cab to be locking with J236 key
All medical cabinet RUD in the cab to be locking with 1250 key
All exterior access RUD for medical cabinets to have satin finish
All exterior access RUD for medical cabinets to be painted job color. Not available on two tone cabs.
Engine compartment light, LED (EA).
Rear cab wall medical cabinet with side access doors (one each side). Cabinet to be 50" high x 38" wide x 24" deep. Includes (2) locking roll‐up doors (satin finish) and (3) adjustable shelves. Lower door openings raised to provide hand clearance.
Interior medical cabinet. Locate to rear of engine cover. Cabinet to be 30" high x 38" wide x 20" deep with a locking roll up door. Includes (1) adjustable shelf.
Medical cabinet. Locate center on rear wall (20" wide x 24" deep x 52" high). Includes (3) adjustable shelves and (1) vertically mounted incandescent light.
Medical cabinet. Locate center on rear wall (20" wide x 21" deep x 52" high). Includes (3) adjustable shelves and (1) vertically mounted incandescent light.
Medical cabinet mounted on rear wall of cab 48X32X24 with a locking roll up door and windows in door slats. Lower door opening raised to provide hand clearance.
Communication cabinets (PR). (1) each side rearward facing with hinged access door. Each cabinet includes (2) adjustable shelves and (1) incandescent light mounted up high. To have compartment vents as required.
PRICE
$2,179.00
$4,516.00
$4,246.00
$2,896.00
$3,611.00
$2,710.00
$2,710.00
$0.00
$0.00
$1,291.00
$0.00
$143.00
$148.00
$148.00
$0.00
$271.00
$255.00
$3,289.00
$3,371.00
$2,971.00
$2,844.00
$4,835.00
$3,556.00
Option No.
1535‐0045
1535‐0046
1535‐0047
1535‐0048
1535‐0049
1535‐0050
1535‐0051
1535‐0052
1535‐0053
1535‐0054
1535‐0055
1535‐0056
1535‐0057
1535‐0058
1535‐0059
1535‐0060
1535‐0061
1535‐0062
1535‐0063
Description
ALS interior ‐ Style ''A''. Includes forward wall with center locking roll‐up door for access from int, small compts up high ea side of ctr opening with glove box latch on driver's side compt and Medco keyed lock on officer's side, strikers high and low on ALS doors, access plts on int panel of ALS doors, approx 5"W x 17"H x 70"L backboard sleeve, two adj shelves ahead of backboard sleeve and a roll‐out tray with 36" slides each side on floor.
Medical cabinet mounted on rear wall of cab 60X40X23 with a locking roll up door. Lower door opening raised 12" to provide area for rear heaters. Includes lower ventilation, front access and removable sub‐floor for additional access.
Medical cabinet mounted on the officer side rear cab wall 55(54 as required)X18X12 with a locking roll up door. Lower door opening raised to provide hand clearance.
Medical cabinet mounted on the driver side rear cab wall 55(54 as required)X18X12 with a locking roll up door. Lower door opening raised to provide hand clearance.
Louvers for interior medical/ ALS cabinet wall(s) to help cabinet contents to maintain cab interior temperatures. The louvers to be in four sets of three, located two high and two low. Location: [#LOC].
Medical cabinet on rear wall of cab. Reference 131288 #1‐H‐0468 and 1‐H‐07A.
Compartment rear side of cab ''under riser'' type. Approx 22W x 30H opening. Includes double pan hinged door. Location: driver and officer side.
Medical cabinet mounted on rear wall of cab 52" x 40" x 23" with a locking roll up door. Lower door opening raised 4" to provide area for radio installation. Includes lower ventilation and removable sub‐floor for additional access.
ALS interior ‐ Style 'B''. Includes forward wall with center locking roll‐up door for access from int, compts up high ea side of ctr opening with glove box latch on driver's side compt and Medco keyed lock on officer's side, strikers high and low on ALS doors, access plts on int panel of ALS doors, approx 5"W x 17"H x 70"L backboard sleeve, two adj shelves ahead of backboard sleeve and a roll‐out tray with 36" slides each side on floor.
Exterior access roll up doors for medical cabinets to be painted upper cab color.
Cab medical/storage cabinet(s) finish to be Zolatone black. Exterior of bolt‐in cabinets; interior and exterior of weld‐in cabinets.
All map boxes in the cab to be painted Zolatone black.
Driver side cab wheel well medical cabinet approximately 42 x 22 (25 Quest) x 28. Includes external locking pan door painted job color and interior hinged full height door with locking push‐button latch. Cabinet includes (2) adjustable shelves.
Medical cabinet mounted on rear wall of cab 48X42X20 with angled corners and locking roll up door. Lower door opening raised to provide hand clearance.
Brace .75 x 2.75 below medical cabinet shelf
Rear cab wall medical cabinet with side access doors (one each side). Cabinet to be 62" high x 38" wide x 24" deep. Includes (2) locking roll‐up doors (satin finish) and (3) adjustable shelves. Lower door openings raised to provide hand clearance.
Driver side cab wheel well medical cabinet approximately 42x22(25 Quest)x28. Includes external locking pan door painted job color and interior locking roll‐up door with satin finish. Cabinet includes (2) adjustable shelves.
Interior medical cabinet. Locate to rear of engine cover. Cabinet to be 30" high x 38" wide x 20" deep with a locking roll up door. Includes (1) adjustable shelf and forward facing drop down door.
Officer side cab wheel well medical cabinet approximately 42x22(25 Quest)x28. Includes external locking single door painted job color and interior hinged door with locking push‐button latch. Cabinet includes (2) adjustable shelves.
PRICE
$9,422.00
$3,426.00
$2,731.00
$2,731.00
$190.00
$4,516.00
$1,252.00
$3,426.00
$9,677.00
$271.00
$0.00
$0.00
$2,614.00
$4,246.00
$94.00
$3,544.00
$2,868.00
$3,469.00
$2,614.00
Option No.
1535‐0064
1535‐0065
1535‐0066
1535‐0067
1535‐0068
1535‐0069
1535‐0070
1535‐0071
1535‐0072
1535‐0073
1535‐0074
1535‐0075
1535‐0076
1535‐0077
1535‐0078
1535‐0079
1535‐0080
Description
Rear cab wall medical cabinet with side access doors (one each side). Cabinet to be 48" high x 38" wide x 24" deep. Includes (2) locking roll‐up doors (satin finish) and (3) adjustable shelves. Lower door openings raised to provide hand clearance.
Rear wall lower medical front to have a removable front plate. Plate to be painted to match cabinet.
Interior medical cabinet. Locate to lower rear of engine cover. Cabinet to be 32" high x 30" wide x 24" deep with single pan double bi‐
fold doors. Includes (1) vertical and (1) horizontal partition centered in the cabinet, louvered lower side walls and removable lower rear facing panel for installation of heaters.
ALS ‐ Side access. Includes compts on each side of cab, access up high each side of interior outboard with glove box latches, strikers high and low on ALS doors (CIIX/TyphoonX only), access plts on int panel of ALS doors (CIIX/TyphoonX only), extended cab floor and three adj shelves.
Rear wall medical cabinets. Includes forward wall and (2) full height, equal width locking roll‐up door compts with (3) shelves in each compt.
Rear cab wall medical cabinet with side access doors (one each side). Cabinet to be 50" high x 30" wide x 24" deep. Includes (2) locking roll‐up doors (satin finish) and (3) adjustable shelves. Lower door openings raised to provide hand clearance.
Riser for medical cabinet. Lifts bottom of cabinet up to top of rear wall seat support. Front of riser to be closed, sides to be open. CII X / Typhoon X only.
ALS interior ‐ Style ''A''. Includes forward wall with center locking roll‐up door for access from int, small compts up high ea side of ctr opening with glove box latch on driver's side compt and Medco keyed lock on officer's side, strikers high and low on ALS doors, access plts on int panel of ALS doors, approx 5"W x 17"H x 70"L backboard sleeve, two adj shelves ahead of backboard sleeve and a roll‐out tray with 36" slides each side on floor. HCFD.
Rear cab wall medical cabinet with side diamond plate access doors (one each side) mounted above support channel on back wall. Cabinet to be 38" high x 47.25" wide x 14" deep. Includes diamond plate doors hinged to the rear with d‐ring latches and (2) adjustable shelves.
Officer side cab wheel well medical cabinet approximately 42 x 22 (25 Quest) x 28. Includes external locking pan door painted job color and interior hinged full height door with locking push‐button latch. Cabinet includes (2) adjustable shelves.
All medical cabinet RUD in the cab to be locking with CH751 key.
Driver side cab wheel well medical cabinet approximately 42x22(25 Quest)x28. Includes external locking roll‐up door and interior hinged door with locking push‐button latch. Cabinet includes (1) adjustable partition installed and (2) adjustable shelves shipped loose in the cabinet.
Driver side cab wheel well medical cabinet approximately 42x22(25 Quest)x28. Includes external pan door with locking Tri‐Mark latch painted job color and interior full height hinged door with locking push‐button latch. Cabinet includes (2) adjustable shelves.
Officer side cab wheel well medical cabinet approximately 42x22(25 Quest)x28. Includes external pan door with locking Tri‐Mark latch painted job color and interior full height hinged door with locking push‐button latch. Cabinet includes (2) adjustable shelves.
Interior medical cabinet. Locate to rear of engine cover. Cabinet to be 25.5" high x 30" wide x 23" deep with (2) drop down doors.
All roll‐up medical cabinet doors selected on the cab to be Amdor brand.
Officer side cab wheel well medical cabinet approximately 42x22(25 Quest)x28. Includes external locking roll‐up door. Cabinet includes (2) adjustable shelves.
PRICE
$3,289.00
$0.00
$3,405.00
$3,759.00
$10,302.00
$3,289.00
$757.00
$20,424.00
$3,289.00
$2,614.00
$148.00
$2,300.00
$2,780.00
$2,780.00
$1,124.00
$143.00
$1,949.00
Option No.
1535‐0081
1535‐0082
1535‐0083
1535‐0084
1535‐0085
1535‐0086
1535‐0087
1535‐0088
1535‐0089
1535‐0090
1535‐0091
1535‐0092
1535‐0093
1535‐0094
1535‐0095
1535‐0096
Description
Driver side cab wheel well medical cabinet approximately 42x22(25 Quest)x28. Includes external locking roll‐up door. Cabinet includes (2) adjustable shelves.
11"H x 18"W access opening with cargo net cover on driver and officer side wheel well medical cabinets back wall(engine cover side)up high. Includes deflector plate on ceiling to protect roll‐up door.
Cabinet officer side behind officer seat with a Norcold DE‐0740 refrigerator. Cabinet to include a garage style roll‐up door (no lighting but wired to door ajar indicator). Wire refrigerator to operate thru shore line and during transit and on scene.
Full width cabinet along upper forward vista area of cab. To include two drop down doors with push‐button latching. Two LED lights to be mounted in the upper area of the cabinet. Each door to wired to door adjar indicator. Final design to be discussed with customer
Rear cab wall medical cabinet with side access doors (one each side). Cabinet to be 36" high x 38" wide x 24" deep. Includes (2) roll‐up doors (satin finish) and (2) adjustable shelves. Lower door openings raised to provide hand clearance.
Driver and officer side cab wheel well medical cabinet approximately 17x23x28. Includes internal locking vertically hinged door. Quest cabs only.
Special medical cabinet on rear wall. Includes lower area ROM door with satin finish (front lower area raised 6")and lock, (1) fixed shelf and (2) adjustable (above)‐All with 1" lips all the way around, upper area with drop down down with (2) non‐locking push buttons, lower sides open with cargo nets, upper side officer with vertically hinged door with Medeco3 cam lock with (2) alike keys (each unit to be keyed differently). See full design in file.
Riser for medical cabinet. Approx 40"W x 20"D x 17"H. Front of riser to have a drop down door with two locking latches. Finish to match medical cabinet.
Full width cabinet along upper rearward vista area of cab. To include three (3) lift‐up doors with push‐button latching (hold‐opens for each as size of door permits). Each opening to include one (1) ROM LED strip light mounted in the upper area of the cabinet. Each door to wired to door ajar indicator.
Medical cabinet mounted on rear wall of cab 48X40X23 with a locking roll up door. Lower door opening raised 4" to provide area for radio installation. Includes lower ventilation and removable sub‐floor for additional access.
Officer side cab wheel well medical/communication cabinet approximately 42x22(25 Quest)x28. Includes external half height locking pan door with Tri‐Mark latch painted job color and interior full height opening with cargo netting. Cabinet includes (3) adjustable interior pull‐
out shelves.
Driver side cab wheel well medical/communication cabinet approximately 42x22(25 Quest)x28. Includes external half height locking pan door with Tri‐Mark latch painted job color and interior full height opening with cargo netting. Cabinet includes (3) adjustable interior (4) sided trays with 1" lips.
Compartment rear side of cab ''under riser'' type. Approx 22W x 30H opening. Includes double pan hinged door with Tri‐Mark locking latches. Location: driver and officer side.
Driver side cab wheel well medical cabinet approximately 42x22(25 Quest)x28. Includes external pan door with locking Tri‐Mark latch painted job color and interior full height opening with cargo net cover. Cabinet includes (2) adjustable shelves.
Officer side cab wheel well medical cabinet approximately 42x22(25 Quest)x28. Includes external pan door with locking Tri‐Mark latch painted job color and interior full height opening with cargo net cover. Cabinet includes (2) adjustable shelves.
Exterior access roll up door for medical cabinet to be painted two‐tone to match cab paint break (EA).
PRICE
$1,949.00
$843.00
$4,025.00
$3,737.00
$3,289.00
$1,466.00
$9,176.00
$984.00
$3,737.00
$3,426.00
$3,438.00
$3,438.00
$1,419.00
$2,954.00
$2,954.00
$461.00
Option No.
Description
PRICE
1535‐0097
Medical cabinet mounted on the wheel well officer side of cab 15.5X24X21 with a vertically hinged door and locking push‐button latch.
Upper forward vista area cabinet. Cabinet to be full width and height of vista area forward of rear cab doors. Includes (3) horizontal hinged lift‐up doors. Outboard compartments to be approx. 12" wide.
Upper rearward vista area cabinet. Cabinet to be full width and height of vista area rearward of rear cab doors. Includes (3) horizontally hinged lift‐up doors. Outboard compartments to be approx. 12" wide.
Medical cabinet mounted on the driver side rear cab wall 55X28X12 with a locking roll up door. Lower door opening raised 12" to provide space for rear heater. Includes lower ventilation, front access and removable sub‐floor for additional access.
Medical cabinet mounted on the officer side rear cab wall 55X28X12 with a locking roll up door. Lower door opening raised 12" to provide space for rear heater. Includes lower ventilation, front access and removable sub‐floor for additional access.
Medical cabinet ‐ ALS style side access. Includes compt on officer side of cab, access up high on interior with glove box latch, extended cab floor and three adj shelves. Includes pass‐thru under bench seat riser if equipped.
$1,081.00
1535‐0098
1535‐0099
1535‐0100
1535‐0101
1535‐0102
1535‐0103
1535‐0104
1535‐0105
1535‐0106
1535‐0107
1535‐0108
1535‐0109
1535‐0110
1535‐0111
1535‐0112
1535‐0113
1535‐0114
Compartment rear side of cab ''under riser'' type. Approx 22W x 30H opening. Includes double pan hinged door. Location: driver side.
Medical cabinet mounted on the driver side rear cab wall with a locking roll up door. Cabinet to be approx 53H x 18W x 12D. Bottom of exterior opening just above rear seat channel. Includes 2 adj shelves in upper area, false floor at top of seat channel and interior door below false floor. Interior door to be vert hinged on inboard side.
Medical cabinet mounted on the officer side rear cab wall 55(54 as required)X18X12 with a locking roll up door. Lower door opening raised approx. 12" to provide space for rear wall heaters. Includes slots and false floor.
Medical cabinet mounted on the driver side rear cab wall 55(54 as required)X18X12 with a locking roll up door. Lower door opening raised approx. 12" to provide space for rear wall heaters. Includes slots and false floor.
Medical cabinet ‐ driver side cab wheel well. Includes (1) external locking roll‐up door (satin finish), (1) vertically‐hinged internal door with locking push button latch, (2) adjustable shelves. Custom ES.
Medical cabinet ‐ officer side cab wheel well. Includes (1) external locking roll‐up door (satin finish), (1) vertically‐hinged internal door with locking push button latch, (2) adjustable shelves. Custom ES.
Compartment rear side of cab below floor. Approx 22W x 19.5H opening. Includes double pan hinged door with Tri‐Mark latch. Location: driver and officer side.
Medical cabinet mounted on the driver side rear cab wall 55(54 as required)X20X22 with a locking satin finish roll‐up door and (3) adjustable shelves.
Medical cabinet mounted on the officer side rear cab wall 55(54 as required)X20X22 with a locking satin finish roll‐up door and equipment rack.
Officer side cab wheel well medical cabinet approximately 42x22(25 Quest)x28. Includes external locking pan door painted job color and interior locking roll‐up door with satin finish. Cabinet includes (2) adjustable shelves.
(2) Cabinets rear of commercial extended cab. Sized in height, width and depth as space within cab permits while allowing for installation requirements for a commercial chassis. Each cabinet to include (1) LED strip light mounted as applicable. Cabinets to be bolt‐in and have zolatone grey interior and exterior finish.
Medical cabinet mounted on the wheel well driver side of cab 44HX21WX16D with a locking roll up door.
$3,201.00
$3,201.00
$3,088.00
$3,088.00
$2,663.00
$1,252.00
$3,881.00
$2,731.00
$2,731.00
$1,186.00
$1,186.00
$1,419.00
$2,858.00
$2,858.00
$2,868.00
$3,578.00
$2,630.00
Option No.
1535‐0115
1535‐0116
1535‐0117
1535‐0118
1535‐0119
1535‐0120
1535‐0121
1535‐0122
1535‐0123
1535‐0124
1535‐0125
1535‐0126
1535‐0127
1535‐0128
1535‐0129
1535‐0130
1535‐0131
Description
Special medical cabinet on rear wall. Includes lower side access only with (2) adjustable shelves with 1" lips all the way around, (1) fixed shelf with 1" lips all the way around, upper front area with drop down door with (2) non‐locking push buttons, lower sides open with cargo nets attached with clips in lieu of snaps, upper side officer with vertically hinged door with Medeco3 cam lock with (2) alike keys (each unit to be keyed differently). See full design in file.
Equipment bag storage rack; finish to match cab interior. Location: officer side rear wall medical cabinet.
Medical cabinet(s) interior finish and components (shelves/trays) to match interior cab finish.
PRICE
Medical cabinet mounted on rear wall of cab 50X38X12 with locking roll up door. Lower door opening raised to provide hand clearance.
Medical cabinet mounted on rear wall of cab 55X40X23 with a locking roll up door. Cabinet floor to be level with top of PTO box on cab floor.
Medical cabinet mounted on the officer side rear cab wall full height (as applicable)X 18W X 12D with a locking roll up door. For use with vista cabs only. Lower door opening raised to provide hand clearance.
Medical cabinet mounted on rear wall of cab full height (as applicable)X55X22 with locking roll up door. For use with vista cabs only. Lower door opening raised to provide hand clearance.
Medical cabinet mounted on the driver side rear cab wall full height (as applicable)X 18W X 12D with a locking roll up door. For use with vista cabs only. Lower door opening raised to provide hand clearance.
Full width cabinet along upper forward vista area of cab. To include three (3) lift‐up doors with push‐button latching (hold‐opens for each as size of door permits). Each opening to include one (1) ROM LED strip light mounted in the upper area of the cabinet. Each door to wired to door ajar indicator.
Medical cabinet mounted on the driver side rear cab wall 55(54 as required)X20X22 with a locking satin finish roll‐up door and (3) adjustable shelves. Includes lower area raised to accomodate rear wall heater.
Medical cabinet mounted on the officer side rear cab wall 55(54 as required)X20X22 with a locking satin finish roll‐up door, (1) adjustable shelvf and equipment rack. Includes lower area raised to accomodate rear wall heater.
Medical cabinet mounted on the wheel well driver side of cab 32H x 21W x 24D with a interior hinged full height door with locking push‐
button latch; hinged inboard.
Louvers for rear wall bench seat riser to help cabinet contents to maintain cab interior temperatures. The louvers to be in three sets of three, located low on forward wall.
ALS ‐ Side access. Includes compts on each side of cab, 16Wx20H access up high each side of interior outboard with locking glove box latches, strikers high and low on ALS doors, access plts on int panel of ALS doors, extended cab floors, smooth plate rear kick plates, one adj shelf and nylatron floor overlay. Includes pass‐thru under bench seat if equipped.
Reverse hinge driver and officer side ALS compartment door. Includes vertically mounted drip rail along forward area of compartment opening (as applicable)(in addition to the horizontal drip rail above the door opening; CIIX and TyphoonX cabs only). Doors to open approx. 110 degrees.
Driver side cab wheel well medical cabinet approximately 42 x 22 (25 Quest) x 28. Includes external locking roll‐up door and interior hinged door with locking push‐button latch; hinged outboard. Cabinet includes (2) adjustable shelves.
Driver side cab wheel well medical cabinet approximately 42 x 24 (27 Quest) x 28. Includes external locking roll‐up door and interior hinged door with locking push‐button latch. Cabinet includes (2) adjustable shelves.
$4,161.00
$8,601.00
$264.00
$264.00
$3,426.00
$2,846.00
$4,591.00
$2,846.00
$3,737.00
$2,860.00
$2,860.00
$2,308.00
$190.00
$3,759.00
$163.00
$2,179.00
$2,179.00
Option No.
1535‐0132
1535‐0133
1535‐0134
1535‐0135
1535‐0136
1535‐0137
1535‐0138
1535‐0139
1535‐0140
1535‐0141
1535‐0142
1535‐0143
1535‐0144
1535‐0145
1535‐0146
1535‐0147
1535‐0148
1535‐0149
1535‐0150
1535‐0151
Description
Officer side cab wheel well medical cabinet approximately 42 x 24 (27 Quest) x 28. Includes external locking roll‐up door and interior hinged door with locking push‐button latch. Cabinet includes (2) adjustable shelves.
Cab medical/storage cabinet(s) interior finish to be Zolatone gray.
All roll‐up medical cabinet doors selected on the cab to be Gortite brand.
Driver side cab wheel well medical cabinet approximately 42 x 22 (25 Quest) x 28. Includes external locking roll‐up door and interior hinged smoked lexan door with locking push‐button latch. Cabinet includes (2) adjustable shelves.
Rear cab wall medical cabinet with front and side access doors (one each side). Cabinet to be 42" high x 30" wide x 32" deep (do not notch for support bracket; customer to store backboard(s) above support channel behind cabinet; install mounting bracket above cabinet). Includes (1) locking lower horizontally hinged plate door on front located below roll‐up door drums, (2) locking side roll‐up doors (satin finish) and (2) adjustable shelves. Lower door openings raised to provide hand clearance.
Medical cabinet mounted on the wheel well driver side of cab 45H x 21W x 24D with a locking roll‐back (bread box) door.
Lock box mounted in the driver side wheel well medical cabinet floor. 14X21X20 with a locking horizontally hinged door. Finish will match interior of cab.
ALS interior with backboard and stokes basket storage. Includes forward wall with (2) outboard locking roll‐up doors for access from int, (3) compts up high with glove box latches, strikers high and low on ALS doors, access plts on int panel of ALS doors, (2) approx 5"W x 17"H x 70"L backboard sleeves and stokes basket storage below backboard sleeves on floor.
Medical cabinet mounted on the officer side rear cab wall 55(54 as required)X18X12 with a locking full height door hinged inboard.
Medical cabinet mounted on the driver side rear cab wall 55(54 as required)X18X12 with a locking full height door hinged inboard.
Wheel well medical cabinet interior door(s) to be hinged outboard.
Lock box mounted on top of the rear wall medical cabinet. 14HX18WX12D with a locking horizontally hinged drop down door. Finish will match interior of cab.
11"H x 18"W access opening with cargo net cover on officer side of rear wall medical medical cabinet down low.
ALS ‐ Side access. Includes compts on each side of cab, strikers high and low on exterior doors, access plts on int panel of exterior doors, full height satin finish Amdor roll‐up doors on interior, extended cab floor and three adj shelves.
Upper rearward vista area cabinet. Cabinet to be between full height exterior ALS style cabinets and the same height of vista area. Includes (1) horizontally hinged lift‐up door.
Officer side cab wheel well medical/communication cabinet approximately 42x22(25 Quest)x28. Includes external half height locking pan door with Tri‐Mark latch painted job color and interior full height opening with cargo netting. Cabinet includes (1) adjustable shelf.
All medical cabinet RUD in the cab to be locking with GEM key lock
Officer side cab wheel well medical cabinet approximately 42x24x28. Includes external locking pan door painted job color and raised boxed interior locking roll‐up door with satin finish for a 42" opening. Cabinet includes (2) adjustable shelves. Requires vista cab roof and removal of side windows.
Medical cabinet mounted on the wheel well officer side of cab 45H x 21W x 24D with a interior hinged full height door with locking push‐
button latch; hinged inboard.
Upper forward center vista area cabinet. Cabinet to be 40W x Vista Height x taper with vista deep. Includes horizontally hinged lift‐up door.
PRICE
$2,179.00
$390.00
$250.00
$2,237.00
$3,634.00
$2,710.00
$639.00
$10,226.00
$2,501.00
$2,501.00
$0.00
$639.00
$423.00
$5,513.00
$2,149.00
$3,273.00
$148.00
$3,094.00
$2,308.00
$979.00
Option No.
1535‐0152
1535‐0153
1535‐0154
1535‐0155
1535‐0156
1535‐0157
1535‐0158
1535‐0159
1535‐0160
1535‐0161
1535‐0162
1535‐0163
1535‐0164
1535‐0165
1535‐0166
1535‐0167
1535‐0168
1535‐0169
1535‐0170
Description
**(Use 1535‐0038)Interior medical cabinet. Locate to rear of engine cover. Cabinet to be 30" high x 38" wide x 20" deep with a locking roll up door. Includes (1) adjustable shelf.
Medical cabinet mounted on rear wall of cab 48 x 36 x 20 with a locking roll‐back (bread box) door.
Medical cabinet mounted on the wheel well driver side of cab 45H x 21W x 24D with a interior hinged full height door with locking push‐
button latch; hinged inboard.
PRICE
Medical cabinet mounted on the wheel well driver side of cab 45H x 21W x 24D with a locking roll‐up door and (2) adjustable shelves.
Medical cabinet rear engine cover, bolted to forward facing map box approximately 34Wx25Hx18D. To include one (1) adjustable shelf. Two (2) vertically hinged swing out doors shall allow access (to the rear), the doors shall be raised 6" up from the cabinet's base. The cabinet shall include push‐button latching, (2) each door (1) top and (1) bottom.
ALS ‐ Side access. Includes compts on each side of cab, strikers high and low on exterior doors, access plts on int panel of exterior doors, satin finish ROM roll‐up doors on interior (bottom raised to riser height), extended cab floor and three adj shelves
Locking interior medical cabinet plate door (PR). Key type to be 1250.
$2,710.00
Medical cabinet mounted on the wheel well officer side of cab 22X21X28 with a vertically hinged door and locking push‐button latch.
ALS ‐ Side interior cabinets. Includes full height access doors (raised for heaters if equipped) each side of interior outboard with glove box latches and three adj shelves.
Compartment rear side of cab ''under riser'' type. Approx 22W x 30H opening. Includes double pan hinged door. For use with heaters below bench seat (No pass‐through). Location: driver and officer side.
Officer side cab wheel well medical cabinet approximately 42 x 24 (25 Quest) x 28. Includes external locking roll‐up door and interior cargo net access. Cabinet includes (2) adjustable shelves.
Driver side cab wheel well medical cabinet approximately 42 x 24 (25 Quest) x 28. Includes external locking roll‐up door and interior cargo net access. Cabinet includes (2) adjustable shelves.
Compartment rear side of cab. Approx 8.75"W x 25"H opening. Includes a 3/16" smooth plate doors painted job color with quarter turn D‐ring latch. Cut floor in cab to accommadate the height. Location: driver side.
Compartment rear side of cab. Approx 8.75"W x 25"H opening. Includes a 3/16" smooth plate doors painted job color with quarter turn D‐ring latch. Cut floor in cab to accommadate the height. Location: officer side.
The bottom of the medical cabinet(s) within the cab shall have stainless steel trim at the bottom. This kick plate trim shall be 4" in height from the floor and shall be trimmed as required for door opening(s) below 4".
Compartment rear side of cab below floor. Approx 9W x 19.5H opening. Includes double pan hinged doors. Long cab with medium door location only. Location: driver and officer side.
All cab exterior ALS/medical cabinet doors to have 1250 keyed locks.
Medical cabinet mounted on rear wall of cab 55X38X16 with a locking roll up door. Lower door opening raised to provide hand clearance.
Cab compartment ‐ (1) each side rear of front wheels and below the cab transverse compartment. Approx 18 wide x 10.75 tall. To have an aluminum door with D‐Ring (non‐locking), slam latch, hinged to the front. Door design must seal the compartment, to secure and protect medical equipment.
$1,081.00
$3,301.00
$4,246.00
$2,308.00
$1,516.00
$5,739.00
$163.00
$3,759.00
$1,252.00
$2,236.00
$2,236.00
$955.00
$955.00
$437.00
$1,002.00
$0.00
$3,426.00
$1,419.00
Option No.
1535‐0171
1535‐0172
1535‐0173
1535‐0174
1535‐0175
1535‐0176
1535‐0177
1535‐0178
1535‐0180
1535‐0181
1535‐0182
1535‐0183
1535‐0184
1535‐0185
1535‐0186
Description
Medical cab contents mounted on the wheel well of cab (cabinet approximately 31"H X 44"W). There shall be a transverse vertical divider approximately 8" rearward of forward wall, used to store a stokes basket. A second vertical divider approximately 10" rearward of the first divider (approximately 18" from forward wall) shall provide transverse storage. A horizontal divider shall be placed between the1st and 2nd vertical partitions, it shall be placed approximately 10" up from the floor to provide approximately a 10" X 10" transverse storage area for the tripod. Above the tripod storage 2 backboards shall be stored with a vertical divider to separate them in 2 transverse storage areas approximately 5" X 21" each (directly above the tripod storage area.. Rearward of the stokes, tripod and backboard transverse storage area the remaining compartment shall be shall be 1/2 transverse depth (or divided left and right). This rearward most area shall not be transverse.
Rear cab wall medical cabinet to be 50" high x 38" wide x 24" deep. Includes (1) forward facing locking roll‐up door (satin finish) and (3) adjustable shelves. Lower door openings raised to provide hand clearance.
ALS ‐ Side access. Includes compartments on each side of cab, strikers high and low on exterior doors. Includes access plates on interior panel of exterior doors, satin finish ROM roll‐up doors on interior (bottom raised to riser height), extended cab floor and three adjustable
shelves. Cabinet Includes transverse riser with backboard storage. The interior riser jets/protrudes forward between side wall ALS cabinets to allow heaters (if so equipped) not interfere or impede upon transverse storage/ pass‐thru of backboards and other equipment stored under the riser in the transverse storage area.
ALS door locks ‐ electric. Electric lock for hinged ALS doors. Wire to same electric lock system as other cab doors.
Medical cabinet mounted on rear wall of cab 49 x 40 x 25.5. Side access lower section with cargo net and notch upper forward access with discrete compartment. Includes drop down door.
Medical cabinet mounted on rear wall of cab approximately 48 x 38 x 20 with locking roll up door. Lower door opening raised to provide hand clearance. Required with rear outboard fold down seat(s).
Compartment rear side of cab ''under riser'' type. Approx 9W x 30H opening. Includes double pan hinged door and pass through to bench if equipped. Long cab with medium door location only. Location: driver and officer side.
Compartment rear side of cab below floor. Approx 22W x 19.5H opening. Includes double pan hinged door. Location: driver and officer side.
Cab medical/storage cabinet(s) finish to be Zolatone "Dark Red" 20‐78. Exterior of bolt‐in cabinets; interior and exterior of weld‐in cabinets.
Upper rearward center vista area cabinet. Cabinet to be 48W x Vista Height x 12D. Includes horizontally hinged lift‐up door.
Officer side cab wheel well medical cabinet approximately 42 x 24 (27 Quest) x 28. Includes external locking roll‐up door and interior cargo net access. Cabinet includes (2) adjustable shelves.
Driver side cab wheel well medical cabinet approximately 42 x 24 (27 Quest) x 28. Includes external locking roll‐up door and interior cargo net access. Cabinet includes (2) adjustable shelves.
Medical cabinet mounted on rear wall of cab 55 x 38 x 20 with a locking roll up door. Lower door opening raised to provide hand clearance.
Two (2) compartments rear side of cab below floor (1) driver and (1) officer. Approx 22W x 19.5H opening. Each includes a double pan hinged door with a Tri‐Mark latch.
Medical cabinet mounted on rear wall of cab 48 x 40 x 17 with locking roll up door. Lower door opening raised to provide hand clearance.
PRICE
$1,566.00
$3,289.00
$6,166.00
$1,010.00
$3,684.00
$4,246.00
$1,002.00
$1,252.00
$0.00
$979.00
$2,236.00
$2,236.00
$3,611.00
$2,835.00
$4,246.00
1535‐0196
Description
Driver side cab wheel well medical cabinet approximately 42 x 24 (25 Quest) x 28. Includes external locking roll‐up door and interior hinged door with locking push‐button latch. Cabinet includes (2) adjustable shelves.
Officer side cab wheel well medical cabinet approximately 42 x 24 (25 Quest) x 28. Includes external locking roll‐up door and interior hinged door with locking push‐button latch. Cabinet includes (2) adjustable shelves.
All cab exterior ALS doors to have CH751 keyed locks.
All shelves within the medical cabinet(s) shall have the a full perimeter lip IPOS.
All exterior access RUD for medical cabinets to be painted [#COL].
The interior medical cabinet shall include stainless steel trim on the vertical corner of the cabinet where the hinge is attached. The trim shall run full height of the cabinet on this corner. The trim shall be 1" x 1" to protect and dress off this single corner's edge.
Medical cabinet mounted on the wheel well officer side of cab 15.5X24X21 with rear facing cargo netting.
Driver side cab wheel well medical cabinet approximately 42 x 22 (25 Quest) x 28. Includes external locking roll‐up door and interior hinged door with locking push‐button latch.
Officer side cab wheel well medical cabinet approximately 42 x 22 (25 Quest) x 28. Includes external locking roll‐up door and interior hinged door with locking push‐button latch.
Interior medical cabinet. Locate to rear of engine cover. Cabinet to be 27" high x 38" wide x 20" deep with a locking roll up door. Includes (1) adjustable shelf and forward facing drop down door.
1535‐0197
Driver side cab wheel well medical cabinet approximately 42x22(25 Quest)x28. Includes external lift‐up pan door with locking Tri‐Mark latch painted job color, pull strap for door and interior full height opening with cargo net cover. Cabinet includes (2) adjustable shelves.
Option No.
1535‐0187
1535‐0188
1535‐0189
1535‐0190
1535‐0191
1535‐0192
1535‐0193
1535‐0194
1535‐0195
1535‐0198
1535‐0199
1535‐0200
1535‐0201
1535‐0202
1535‐0203
1535‐0204
1535‐0205
1535‐0206
Officer side cab wheel well medical cabinet approximately 42x22(25 Quest)x28. Includes external lift‐up pan door with locking Tri‐Mark latch painted job color, pull strap for door and interior full height opening with cargo net cover. Cabinet includes (2) adjustable shelves.
Officer side cab wheel well medical cabinet approximately 42x22(25 Quest)x28. Includes external locking pan door painted job color and interior cargo net.
Driver side cab wheel well medical cabinet approximately 42x22(25 Quest)x28. Includes external locking pan door painted job color and interior cargo net.
Offset center rear wall medical cabinet 4" to driver side.
Cab medical/storage cabinet(s) finish to be Zolatone gray. Includes interior/exterior of cabinet and shelves/trays if equipped.
Cab medical/storage cabinet(s) finish to be Zolatone black. Includes interior/exterior of cabinet and shelves/trays if equipped.
Cab medical/storage cabinet(s) finish to be Zolatone "Dark Red" 20‐78. Includes interior/exterior of cabinet and shelves/trays if equipped.
Medical cabinet centered on the rear wall of the cab to be 74" wide X 62" tall. The center section on the cabinet will be 22" deep X 25" wide. At the outside edges of the 25" wide section of the cabinet will angle back until it is 10" deep at the outer most point on both sides. The cabinet is to be split into 3 separate sections with each section having (2) adjustable shelves and a locking ROM roll‐up doors. Lower door opening raised to provide hand clearance.
Additional medical cabinet shelf. Location: (2) driver and (2) officer side medical cabinets.
PRICE
$2,179.00
$2,179.00
$0.00
$67.00
$271.00
$221.00
$1,081.00
$1,953.00
$1,953.00
$3,469.00
$3,330.00
$3,330.00
$2,786.00
$2,786.00
$0.00
$0.00
$0.00
$0.00
$7,699.00
$158.00
Option No.
1535‐0207
1535‐0208
1535‐0209
1535‐0210
1535‐0211
1535‐0212
1535‐0213
1535‐0214
1535‐0215
1535‐0216
1535‐0217
1535‐0218
1535‐0219
1535‐0220
1535‐0221
1535‐0222
1535‐0223
1535‐0224
Description
Driver side cab medical cabinet approximately 52Hx48Wx24D. Located rearward of driver side whell well medical cabinet. Includes external hinged double doors with locking d‐ring handle and interior cargo netting. Cabinet includes (2) adjustable shelves.
PRICE
Driver side cab wheel well medical cabinet approximately 42x22(25 Quest)x28. Includes external locking pan door painted job color.
Upper forward vista area cabinet. Cabinet to be full width and height of vista area forward of rear cab doors. Includes (3) horizontally hinged Lexan lift‐up doors. Outboard compartments to be approx. 12" wide.
Officer side cab wheel well medical cabinet approximately 42 x 22 (25 Quest) x 28. Includes external locking roll‐up door, no interior access. Cabinet includes (2) adjustable shelves.
Medical cabinet mounted on the wheel well driver side of cab 42H x 21W x 24D with a locking roll‐up door. For use with LTA cabs.
Medical cabinet mounted on the officer side rear cab wall full height (as applicable)X 18W X 12D with a locking roll up door. For use with vista cabs only. Lower door opening raised to provide hand clearance.
Medical cabinet mounted on the driver side rear cab wall full height (as applicable)X 18W X 12D with a locking roll up door. For use with vista cabs only. Lower door opening raised to provide hand clearance.
Driver side cab wheel well medical cabinet approximately 42 x 22 (25 Quest) x 28. Includes external locking roll‐up door (no interior door).
Rear cab wall medical cabinet with side access doors (one each side). Cabinet to be 50" high x 38" wide x 24" deep. Includes (2) locking roll‐up doors (satin finish) and (2) adjustable shelves. Lower door openings raised to provide hand clearance.
Filler panel above medical cabinet, (3) sided with finish to match other medical cabinet(s). This panel shall dress off the gap between the top of the cabinet and the ceiling.
Officer side cab wheel well medical cabinet approximately 42 x 24 (27 Quest) x 28. Includes external locking roll‐up door, no interior access. Cabinet includes (2) adjustable shelves.
Driver side cab wheel well medical cabinet approximately 42 x 24 (27 Quest) x 28. Includes external locking roll‐up door, no interior access. Cabinet includes (2) adjustable shelves.
Driver side cab wheel well medical cabinet approximately 42x22(25 Quest)x28. Includes external pan door with locking Tri‐Mark latch painted job color and interior locking roll‐up door with satin finish. Cabinet includes (2) adjustable shelves.
Officer side cab wheel well medical cabinet approximately 42x22(25 Quest)x28. Includes external pan door with locking Tri‐Mark latch painted job color and interior locking roll‐up door with satin finish. Cabinet includes (2) adjustable shelves.
Rear cab wall medical cabinet with side access on each side using black cargo netting. Cabinet to be 45" wide X 16"deep X full height (as applicable). Includes cabinet front access door using a smooth plate vertically hinged double door with thumb latches and (3) adjustable shelves. The cabinet will not be notched around rear wall channel.
Driver side cab wheel well medical cabinet approximately 42 x 22 (25 Quest) x 28. Includes external locking pan door painted job color. Cabinet includes (2) adjustable shelves.
Officer side cab wheel well medical cabinet approximately 42 x 22 (25 Quest) x 28. Includes external locking pan door painted job color. Cabinet includes (2) adjustable shelves.
Lock box mounted in the driver side wheel well medical cabinet floor. 8X21X20 with a locking horizontally hinged door. Finish will match interior of cab.
$2,326.00
$5,183.00
$3,420.00
$2,109.00
$2,710.00
$2,846.00
$2,846.00
$1,938.00
$3,256.00
$270.00
$2,179.00
$2,179.00
$2,868.00
$2,868.00
$3,213.00
$2,614.00
$2,614.00
$639.00
Option No.
1535‐0225
1535‐0226
1535‐0227
1535‐0228
1535‐0229
1535‐0230
1535‐0231
1535‐0232
1535‐0233
1535‐0234
1535‐0235
1535‐0236
1535‐0237
1535‐0238
1535‐0239
1535‐0240
Description
Special medical cabinet on rear wall. Includes lower side access only with (2) adjustable shelves with 1" lips all the way around, upper front area with drop down door (approx. 12H x 35W opening) with (2) non‐locking push buttons and louvers for compartment, lower sides open with cargo nets attached with clips in lieu of snaps.
Rear cab wall medical cabinet with side access. Cabinet to be 32" high x 32" wide x 24" deep. Includes (2) black cargo nets and (1) adjustable shelf.
Additional medical cabinet shelf. Location: rear wall medical cabinet.
ALS side access with full height exterior doors. Includes strikers high and low on ALS doors, access plts on int panel of ALS doors, (2) horizontal backboard sleeves approx 12" above floor accessed from officer side, (2) stair chair sleeves above backboards accessed from officer side and (2) stokes backets sleeves above stair chairs accessed from both sides.
Medical cabinet mounted on rear wall of cab 55 x 40 x 15 with a locking roll up door. Lower door opening raised to provide hand clearance.
Lock box in rear wall medical cabinet; floor mounted. 12H X FW X 12D with a locking horizontally hinged drop down door. Finish will match interior of cab.
Notch upper rear top of center rear wall medical cabinet for dealer installed equipment. Notch to be 6"H x 6"D x FW.
Reverse hinge driver and officer side exterior medical cabinet compartment door. Includes vertically mounted drip rail along forward area of compartment opening (as applicable) (in addition to the horizontal drip rail above the door opening).
Upper forward vista area cabinet. Cabinet to be full width and height of vista area forward of rear cab doors. Includes (3) horizontally hinged lift‐up doors. Outboard compartments to be approx. 12" wide. Driver side compartment to include locking latch and partition wall.
Driver side cab wheel well medical cabinet approximately 42x22(25 Quest)x28. Includes external locking pan door painted job color. No shelves provided.
Upper forward vista area cabinet. Cabinet to be full width and height of vista area forward of rear cab doors. Includes (3) equally spaced compartments with driver and center cargo netting and officer lift‐up door.
Compartment rear side of cab ''under riser'' type. Approx 9W x 30H opening. Includes single pan hinged door with 1/4 turn d‐ring handles. Long cab with medium door location only. Location: driver and officer side.
Driver side cab wheel well medical cabinet approximately 28x22(25 Quest)x28. Includes external locking pan door painted job color. No shelves provided.
Special medical cabinet on rear wall. Includes lower side access only with (2) adjustable shelves with 1" lips all the way around, (1) fixed shelf with 1" lips all the way around, upper front area with drop down door with (2) non‐locking push buttons, lower sides open with cargo nets attached with clips in lieu of snaps, upper side officer with vertically hinged door with non‐locking push button latch.
ALS side transverse access. Includes strikers high and low on ALS doors, access plts on int panel of ALS doors, (2) equally spaced vertical paritions up high for backboard sleeves/shovel/misc, (1) floor mounted SlideMaster bi‐directional tray and (1) transverse adjustable shelf between tray and upper storage. Includes extended floor(s).
Medical cabinet mounted on rear wall of cab full height (as applicable)X40X20 with locking roll up door. Lower door opening raised to provide hand clearance.
PRICE
$3,371.00
$2,350.00
$158.00
$9,186.00
$3,446.00
$639.00
$487.00
$163.00
$3,308.00
$2,326.00
$3,201.00
$1,002.00
$2,326.00
$8,601.00
$5,440.00
$4,591.00
Option No.
1535‐0241
1535‐0242
1535‐0243
1535‐0244
1535‐0245
1535‐0246
1535‐0247
1535‐0248
1535‐0249
1535‐0250
1535‐0251
1535‐0252
1535‐0253
1535‐0254
1535‐0255
1535‐0256
1535‐0257
1535‐0258
Description
Upper forward center vista area cabinet. Cabinet to be 40W x Vista Height x 12D at lower area (depth will taper with vista). Includes cargo netting ipo lift‐up door.
Driver side cab wheel well medical cabinet approximately 42 x 22 (25 Quest) x 28. Includes external locking pan door painted job color with Tri‐Mark latch. Cabinet includes (1) adjustable shelf.
Officer side cab wheel well medical cabinet approximately 42 x 22 (25 Quest) x 28. Includes external locking pan door painted job color with Tri‐Mark latch. Cabinet includes (1) adjustable shelf.
Compartment rear side of cab below floor. Approx 9W x 19.5H opening. Includes single pan hinged door with 1/4 turn d‐ring handles. Long cab with medium door location only. Location: driver and officer side.
Upper forward vista area cabinet. Cabinet to be full width and height of vista area forward of rear cab doors. Includes (3) equally spaced compartments with horizontally hinged lift‐up doors, compartment dividers and center locking door latch.
PRICE
Medical cabinet. Locate center on rear wall (20" wide x 24" deep x 52" high) with a locking roll‐up door. Includes (3) adjustable shelves.
Interior medical cabinet. Locate to rear of engine cover. Cabinet to be 22" H x 45" W x 20" D. Cabinet to be open rear with 1" lower lip and a cargo net style cover over rear opening. Inlcudes (1) adjustable shelf.
Interior medical cabinet. Locate to rear of engine cover. Cabinet to be 20.75" H x 45" W x 22" D. Cabinet to have a 2" lip around top, open rear with 1" lower lip, cargo net style cover over rear opening and (1) adj shelf. Interior to be DA finish.
Interior medical cabinet. Locate to rear of engine cover. Cabinet to be 32" high x 45" wide x 18" deep with sliding Lexan doors. Includes (1) adjustable shelf.
Officer side cab wheel well medical cabinet approximately 26 x 22 (25 Quest) x 28. Includes external locking pan door painted job color with Trimark exterior latch, dual nader pins and interior hinged full height door with locking push‐button latch.
$2,971.00
Reverse hinge driver and officer side ALS compartment door. Doors to open approx. 110 degrees. For use with flush doors on QST2.
ALS doors on cab to have external D‐Ring latch with strikers top and bottom. (QST2 Only)
ALS transverse interior with side access. Includes extended floors, (2) adj roll‐out tilt down alum SlideMaster trays (one ea side high), (2) adj roll‐out alum SlideMaster trays (middle area) and (2) floor mounted alum SlideMaster trays. All trays to meet in the center of the compartment.
Rubber floor matting on interior of all medical cabinet floors.
Compartment rear side of cab ''under riser'' type. Approx 9W x 30H opening. Includes double pan hinged door. Long cab with medium door location only. Location: driver side.
Officer side cab wheel well medical cabinet approximately 42x22(25 Quest)x28. Includes external locking pan door painted job color and interior cargo net. Cabinet includes (2) adjustable shelves.
Driver side cab wheel well medical cabinet approximately 42x22(25 Quest)x28. Includes external locking pan door painted job color and interior cargo net. Cabinet includes (2) adjustable shelves.
Medical cabinet mounted on rear wall of cab 63X40X20 with a front locking roll up door, sides open with cargo nets attached with clips in lieu of snaps and (2) adjustable shelves with 1" lips all the way around. Lower door opening raised 12" to provide area for rear heaters. Includes lower ventilation, front access and removable sub‐floor for additional access.
$1,086.00
$2,588.00
$2,588.00
$1,002.00
$3,415.00
$1,289.00
$1,503.00
$3,264.00
$3,170.00
$300.00
$715.00
$7,391.00
$214.00
$1,002.00
$2,954.00
$2,954.00
$4,123.00
Option No.
1535‐0259
1535‐0260
1535‐0261
1535‐0262
1535‐0263
1535‐0264
1535‐0265
1535‐0266
1535‐0267
1535‐0268
1535‐0269
1535‐0270
1535‐0271
1535‐0272
1535‐0273
1535‐0275
Description
Officer side cab wheel well medical cabinet approximately 42 x 22 (25 Quest) x 28. Includes external locking pan door painted job color. Cabinet includes (1) adjustable roll‐out tool board
Driver side cab wheel well medical cabinet approximately 42 x 22 (25 Quest) x 28. Includes external locking pan door painted job color. Cabinet includes (1) adjustable roll‐out tool board
Upper forward vista area cabinet. Cabinet to be full width and height of vista area by approx 20" deep (at the bottom) located forward of rear cab doors. Includes (2) equally spaced compartments with horizontally hinged lift‐up doors, compartment divider and padding along lower rear edge. Cabinet shall match cab interior.
Cab medical/storage cabinet(s) exterior finish to be Zolatone grey. Interior to be Zolatone white; includes shelves/trays if equipped.
ALS ‐ Side access. Includes compts on each side of cab with exterior locking roll‐up doors, extended cab floor and three adj shelves in each cabinet.
ALS ‐ Side access. Includes compts on each side of cab, strikers high and low on exterior doors, access plts on int panel of exterior doors, satin finish ROM roll‐up doors on interior, extended cab floor and three adj shelves. Includes pass‐thru under bench seat (if equipped).
Medical cabinet mounted on rear wall of cab 55X44X20 with angled corners and locking roll up door. Lower door opening raised to provide hand clearance.
Compartment rear side of cab. Approx 22W x 60H opening. Includes double pan hinged door, (3) adjustable upper shelves and (2) 8" diameter tubes recessed 4" in the floor (driver side only). Location: driver and officer side.
Upper forward vista area cabinet. Cabinet to be full width and height of vista area forward of rear cab doors. Includes (3) equally spaced compartments with driver/officer lift‐up doors and center cargo netting.
Officer side cab wheel well medical cabinet approximately 26 x 22 (25 Quest) x 28. Includes external locking pan door painted job color with Trimark exterior latch, dual nader pins and interior hinged full height door hinged outboard with locking push‐button latch.
Medical cabinet mounted on rear wall of cab 48 x 40 x 12 with locking roll up door. Lower door opening raised to provide hand clearance.
Officer side cab wheel well medical cabinet approximately 42x22(25 Quest)x28 divided into (2) areas. Includes half height external locking pan door painted job color and upper interior cargo net. Cabinet includes exterior access only for lower and interior access only for upper.
Driver side cab wheel well medical cabinet approximately 42x22(25 Quest)x28 divided into (2) areas. Includes half height external locking pan door painted job color and upper interior cargo net. Cabinet includes exterior access only for lower and interior access only for upper.
Medical cabinet mounted on rear wall of cab 50X36X14 with non‐locking roll up door. Cabinet mounted at minimum 18" above floor with 3x3 forward post mounts. Vista cabs only.
Compartment dividers with rubber floor matting on interior of vista cabinet floor.
Medical cabinet mounted on rear wall of cab 55 (54 as required) x 30 x 20 with a locking roll up door. Lower door opening raised approx. 12" to provide space for rear wall heaters and notch for transverse riser. Includes louvers and false floor.
PRICE
$3,548.00
$3,548.00
$3,415.00
$0.00
$5,513.00
$5,739.00
$4,246.00
$2,678.00
$3,201.00
$3,170.00
$4,246.00
$2,954.00
$2,954.00
$4,161.00
$268.00
$4,074.00
Option No.
1535‐0276
1535‐0277
1535‐0278
1535‐0279
1535‐0280
1535‐0281
1535‐0282
1535‐0283
1535‐0284
1535‐0285
1535‐0286
1535‐0287
1535‐0288
1535‐0289
1535‐0290
1535‐0291
Description
Medical cabinet mounted on rear wall of cab 40.5X36X16 with non‐locking roll up door. Cabinet mounted at approx. 16" above floor with 3x3 forward post mounts. Includes (2) adjustable shelves.
TBD
ALS ‐ Side access. Includes compts on each side of cab, strikers high and low on ALS doors, access plts on int panel of ALS doors with Tri‐
Mark latches, extended cab floors, smooth plate rear kick plates and two adj shelves. Includes pass‐thru under bench seat if equipped.
Officer side cab wheel well medical cabinet approximately 26 x 22 (25 Quest) x 28. Includes external locking pan door painted job color with Trimark exterior latch and dual nader pins. No interior access.
Interior medical cabinet. Locate to rear of engine cover. Cabinet to be 26" H x 34" W x 14" D. Cabinet to be open rear with a sweep out floor and a cargo net style cover over rear opening. Inlcudes (1) adjustable shelf.
Upper forward vista area cabinet. Cabinet to be full width and height of vista area forward of rear cab doors. Includes (2) equally spaced compartments with horizontally hinged lift‐up doors and compartment divider.
Rear cab wall medical cabinet with side access. Cabinet to be 50" high x 38" wide x 24" deep. Includes (2) black cargo nets and (3) adjustable shelves.
ALS ‐ Side access. Includes compartments on each side of cab, strikers high and low on exterior doors. Includes access plates on interior panel of exterior doors, satin finish ROM roll‐up doors with 23" wide opening on interior (bottom raised to riser height), extended cab floor and three adjustable shelves. Cabinet Includes transverse riser with backboard storage. The interior riser jets/protrudes forward between side wall ALS cabinets to allow heaters (if so equipped) not interfere or impede upon transverse storage/ pass‐thru of backboards and other equipment stored under the riser in the transverse storage area.
Rear cab wall medical cabinet with side access doors (one each side). Cabinet to be 32" high x 38" wide x 24" deep. Includes (2) locking roll‐up doors (satin finish) and (1) adjustable shelf, front bolt‐on access panel and 1"X1" angle on perimeter of top. Lower door openings raised to provide hand clearance.
Upper forward vista area cabinet. Cabinet to be full width and height of vista area forward of rear cab doors. Outboard officer side compartment to be approx. 12" wide; driver and center equally sized. Includes cargo netting over each opening.
Special medical cabinet on rear wall 64x40x20. Includes lower side access only with (2) adjustable shelves with 1" lips all the way around, (1) fixed shelf with 1" lips all the way around, upper full depth front area with drop down door with (2) non‐locking push buttons, lower sides open with cargo nets attached with clips in lieu of snaps.
Driver side cab wheel well medical cabinet approximately 42 x 24 (27 Quest) x 28. Includes external locking pan door painted job color and interior hinged full height door with locking push‐button latch. Cabinet includes (2) adjustable shelves.
Officer side cab wheel well medical cabinet approximately 42 x 24 (27 Quest) x 28. Includes external locking pan door painted job color and interior hinged full height door with locking push‐button latch. Cabinet includes (2) adjustable shelves.
Driver side cab wheel well medical cabinet approximately 32 x 22 (25 Quest) x 28. Includes external locking pan door painted job color. Cabinet includes (1) adjustable shelf.
Officer side cab wheel well medical cabinet approximately 32 x 22 (25 Quest) x 28. Includes external locking pan door painted job color. Cabinet includes (1) adjustable shelf.
Medical cabinet mounted on the wheel well officer side of cab 45H x 21W x 24D with a interior full height opening with cargo net restraint.
PRICE
$4,161.00
$0.00
$4,068.00
$3,170.00
$1,289.00
$3,415.00
$2,831.00
$6,166.00
$3,289.00
$3,201.00
$8,269.00
$2,717.00
$2,717.00
$2,614.00
$2,614.00
$2,308.00
Option No.
1535‐0292
1535‐0294
1535‐0295
1535‐0296
1535‐0297
1535‐0298
1535‐0299
1535‐0300
1535‐0302
1535‐0303
1535‐0304
Description
Medical cabinet mounted on rear wall of cab 55 x 40 x 20 with a locking roll up door. Lower door opening raised 12" to provide area for rear heaters. Includes lower ventilation, front access and removable sub‐floor for additional access.
Compartment, " L " shape, rear side of cab ''under riser'' type. Compartment shall be L‐ shaped to maximize compartment space below the cab floor and around the cab latching hardware. Option requires the cab floor to be extended toward door opening. Below the cab floor the forward portion of the compartment shall be 14" deep and the aft portion shall be 22" deep. The door opening approx 22"W x 30"H. Includes: double pan hinged door, White poly scuff pad added to the upper area of door pan for tray scuff protection. Location: driver and officer side.
Upper forward vista area cabinet. Cabinet to be full width and height of vista area forward of rear cab doors. Includes (3) horizontally hinged lift‐up doors with non locking thumb action lever type latch's & moon spring hold open device. Outboard compartments to be approx. 20" wide. Center compartment to be hinged at roof line and approx 10 " tall. Below the center compartment a shelf shall be provided that spans between the outboard compartments. Cargo net with 1" web and 1" spacing shall be provided for the shelf area at the front of the opening permanently mounted along the ceiling and offer secured access with small plastic / composite buckles along the bottom. Below the outboard compartment a head bump pad shall be provided. Cargo net color: Black. Finish: Shall be consistent with the cab interior.
A "T" shaped medical cabinet shall be provided for max available space and accommodate outboard seating X 22" deep. The lower space shall provide transverse storage for each cab side access door. The center area shall be closed off from the transverse space below and include a non‐locking roll up door with (4) adjustable shelves. The upper portion shall include (2) compartments 22" deep. The compartment shall have an inside dimension of 32" wide x 16" tall. Inside provide a centered vertical divider with (2) mouse hole notches at top & bottom to pass USB cable from charging ports and a shelf located to the outboard side of the divider. The access doors shall be horizontally hinged lift‐up doors with non‐locking thumb action lever type latches and moon spring hold open device. Below the outboard compartments a head bump pad shall be provided. Finish: Shall be consistent with cab interior. Additional EON lights to be provided as applicable to illuminate all areas.
Polished stainless steel trim on bottom and vertical edge of riser height or below floor exterior cab compartment(s).
Interior medical cabinet. Locate to rear of engine cover. Cabinet to be 30" high x 38" wide x 20" deep with a non‐locking roll up door. Includes (1) adjustable shelf.
Medical cabinet mounted on the wheel well driver side of cab 26H x 21W x 24D with an interior hinged full height door with locking d‐
ring.
Medical cabinet mounted on the wheel well officer side of cab 26H x 21W x 24D with an interior hinged full height door with locking d‐
ring.
Medical cabinet mounted on the wheel well officer side of cab 32H x 21W x 24D with a interior full height opening and cargo net restraint.
Medical cabinet mounted on rear wall of cab 48 x 40 x 20 with locking roll up door. Includes (2) adjustable shelves and a floor mounted roll‐out tray. Lower door opening raised to provide hand clearance.
Special medical cabinet on rear wall. Includes lower side access only with (2) adjustable shelves with 1" lips all the way around, upper front area with drop down door (approx. 12H x 35W opening) with (2) locking push buttons and louvers for compartment, lower sides open with cargo nets (1" square openings) attached with clips in lieu of snaps.
PRICE
$3,611.00
$2,241.00
$3,966.00
$7,164.00
$161.00
$3,371.00
$2,258.00
$2,258.00
$2,308.00
$4,957.00
$3,371.00
Option No.
1535‐0305
1535‐0306
1535‐0307
1535‐0308
1535‐0309
1535‐0310
1535‐0311
1535‐0312
1535‐0313
1535‐0314
1535‐0315
1535‐0316
1535‐0317
1535‐0318
1535‐0319
1535‐0320
1535‐0321
1535‐0322
1535‐0323
Description
Interior medical cabinet. Locate to rear of engine cover. Cabinet to be 30" high x 38" wide x 20" deep with single pan locking double doors. Includes (2) adjustable shelves.
Cab medical/storage cabinet(s) behind rear crew cab doors interior finish to be Zolatone gray. Includes cabinet, door(s) and shelves/trays if equipped.
Compartment rear side of cab (PR) without door for pump can storage. Compts to be approx 10.5" W x 30.5" H x 14" D. For use on 67.5" CII cab with med doors.
Cab medical/storage cabinet(s) finish to be Scorpion black. Includes interior/exterior of cabinet and shelves/trays if equipped.
Cabinet mounted on rear wall of cab 48 x 32 x 24 with a non‐locking roll up door. Lower door opening raised 12"‐14" to provide area for rear auxiliary component(s). Includes lower ventilation, front access and removable sub‐floor for additional access.
The compartments to the rear sides of the cab are to be designed with a pass through that extends fully from the driver side compartment to the officer side compartment.To be used when equipped with a bench seat riser or a common riser used with multiple individual seats. Not available with outboard SCBA fold down jump seats. This option will reduce the height of the rear wall medical cabinets if equipped.
Officer side cab wheel well medical cabinet approximately 26 x 22 (25 Quest) x 28. Includes external locking pan door painted job color and interior cargo net.
Driver side cab wheel well medical cabinet approximately 26 x 22 (25 Quest) x 28. Includes external locking pan door painted job color and interior cargo net.
All roll‐up medical cabinet doors selected on the cab to be Hansen brand.
Cabinet mounted on the officer side rear cab wall 55(54 as required)X18X12 with a non‐locking roll up door. Lower door opening raised to provide hand clearance.
Cabinet mounted on the driver side rear cab wall 55(54 as required)X18X12 with a non‐locking roll up door. Lower door opening raised to provide hand clearance.
LINE‐X package: Bolt On Cab medical/storage cabinet(s) finish shall have LINE‐X coating. Includes interior/exterior of cabinet and shelves/trays if equipped. Cabinets welded to the cab shall have the same finish as cab interior.
Medical cabinet mounted on the wheel well officer side of cab 42H x 21W x 24D with a locking roll‐up door.
Driver side cab wheel well medical cabinet approximately 26 x 22 (25 Quest) x 28. Includes external locking pan door painted job color with Tri‐Mark latch. Cabinet includes (1) adjustable shelf.
Driver side cab wheel well medical cabinet approximately 30 x 24 (27 Quest) x 28. Includes external locking pan door painted job color. No interior access.
Officer side cab wheel well medical cabinet approximately 30 x 24 (27 Quest) x 28. Includes external locking pan door painted job color. No interior access.
Reflective [#COL] 3M Diamond Grade striping positioned in the "A" formation located on the medical cabinet pan door panels.
Interior medical cabinet. Locate to rear of engine cover facing aft. Cabinet to be 26" high x 34" wide x 14" deep. Includes: vertical single pan double doors, locking push button lever type latches & (1) adjustable shelf.
Medical cabinet mounted on rear wall of cab 52X35X16 with a locking upper and lower drop down doors. Upper door opening approx. 13" tall with side ventilation. Lower opening to include (2) adjustable shelves.
PRICE
$3,239.00
$0.00
$3,404.00
$169.00
$4,516.00
$0.00
$2,683.00
$2,683.00
$287.00
$2,731.00
$2,731.00
$535.00
$2,710.00
$2,588.00
$2,683.00
$2,588.00
$326.00
$3,239.00
$3,426.00
Option No.
1535‐0324
1535‐0326
1535‐0327
1535‐0328
1535‐0329
1535‐0330
1535‐0331
1535‐0332
1535‐0333
1535‐0334
1535‐0335
1535‐0336
1535‐0337
1535‐0338
1535‐0339
1535‐0340
1535‐0341
1535‐0342
1535‐0343
1535‐0344
Description
Cabinet mounted on rear wall of cab 48 x 32 x 24 with a locking roll up door. Lower door opening raised 12"‐14" to provide area for rear auxiliary component(s). Includes lower ventilation, front access and removable sub‐floor for additional access.
[#COL] Reflexite V98 striping positioned in the "A" formation located on the cab medical cabinet door panels.
Upper rearward split vista cabinet (PR). Cabinets to be full height and width of split vista rearward of rear cab doors. Includes (1) horizontally hinged lift‐up door on each cabinet.
Driver side cab wheel well medical cabinet approximately 42x22(25 Quest)x28. Includes external locking pan door painted job color. No shelves provided; tracks only.
Medical cabinet mounted on the wheel well officer side of cab 45H x 21W x 18D(approx) with a locking roll‐up door.
Medical cabinet mounted on the wheel well driver side of cab 45H x 21W x 18D(approx) with a locking roll‐up door.
Medical cabinet mounted on officer side inboard of rear wall cab 52X20X20 with a locking roll up door facing officer side. Lower door opening raised to provide hand clearance.
Compartment rear side of cab. Approx 9W x 42H opening. Includes single pan hinged doors. Long cab with medium door location only. Location: driver and officer side.
Upper forward vista area cabinet. Cabinet to be full width and height of vista area forward of rear cab doors. Includes (3) horizontally hinged lift‐up doors. Outboard compartments to be approx. 12" wide. Officer side compartment to include locking latch and partition wall.
LINE‐X package: Cabinet(s) behind the rear cab door (non transverse) shall have LINE‐X coating. Includes interior/exterior of cabinet and shelves/trays if equipped.
Cabinet mounted on rear wall of cab 48 x 32 x 20 with a locking roll up door. Lower door opening raised 12"‐14" to provide area for rear auxiliary component(s). Includes lower ventilation, front access and removable sub‐floor for additional access.
Medical cabinet mounted on the wheel well officer side of cab 36H x 21W x 24D with a interior full height opening with cargo net restraint.
Interior medical cabinet. Locate to rear of engine cover. Cabinet to be 20.75" H x 45" W x 22" D. Cabinet to have a 2" lip around top, open rear with 1" lower lip, cargo net style cover over rear opening and (1) adj shelf.
Upper forward vista area cabinet. Cabinet to be full width and height of vista area by approx 20" deep (at the bottom) located forward of rear cab doors. Includes (2) equally spaced compartments with cargo netting, compartment divider and padding along lower rear edge. Cabinet shall match cab interior.
Cabinet mounted on rear wall of cab 52 x 32 x 24 with a locking roll up door. Lower door opening raised 12"‐14" to provide area for rear auxiliary component(s). Includes lower ventilation, front access and removable sub‐floor for additional access.
Rear cab wall medical cabinet with side access doors (one each side). Cabinet to be 50" high x 32" wide x 24" deep. Includes (2) locking roll‐up doors (satin finish) and (3) adjustable shelves. Lower door openings raised to provide hand clearance.
Cabinet mounted on the wheel well driver side of cab 26H x 21W x 24D with an interior full height cargo net cover.
Cabinet mounted on the wheel well officer side of cab 26H x 21W x 24D with an interior full height cargo net cover.
Compartment rear side of cab. Approx 9W x full height opening. Includes single pan hinged door with dual d‐rings. Long cab with medium door location only. Location: driver and officer side.
Medical cabinet mounted on the wheel well driver side of cab 45H x 21W x 24D with a interior full height opening with cargo net restraint.
PRICE
$4,516.00
$263.00
$2,149.00
$2,433.00
$2,710.00
$2,710.00
$3,426.00
$1,339.00
$3,308.00
$535.00
$4,516.00
$2,308.00
$1,503.00
$3,415.00
$4,716.00
$3,289.00
$2,258.00
$2,258.00
$1,883.00
$2,308.00
Option No.
1535‐0345
1535‐0346
1535‐0347
1535‐0348
1535‐0349
1535‐0350
1535‐0351
1535‐0352
1535‐0353
1535‐0354
1535‐0355
1535‐0356
1535‐0357
1535‐0358
1535‐0359
1535‐0360
1535‐0361
1535‐0362
Description
Officer side cab wheel well medical cabinet approximately 26 x 22 (25 Quest) x 28. Includes external locking pan door with Tri‐Mark exterior latch painted job color and interior cargo net.
Driver side cab wheel well medical cabinet approximately 26 x 22 (25 Quest) x 28. Includes external locking pan door with Tri‐Mark exterior latch painted job color and interior cargo net.
PRICE
Officer side cab wheel well medical cabinet approximately 42x22(25 Quest)x28. Includes external locking pan door painted job color.
Medical cabinet mounted on rear wall of cab 50" x 36" x 24" with a locking roll up door. Lower door opening raised approx. 12" ‐ 14" to provide area for component installation. Includes lower ventilation and removable sub‐floor for additional access.
Upper rearward vista area cabinet. Cabinet to be full width and height of vista area rearward of rear cab doors. Includes (2) horizontally hinged lift‐up doors.
Medical cabinet mounted on rear wall of cab full height x 38 x 24 with a locking roll up door. Lower door opening raised to provide hand clearance.
Medical cabinet mounted on the wheel well officer side of cab 45H x 21W x 24D with a interior full height opening, cargo net restraint and no shelves.
Medical cabinet mounted on the wheel well driver side of cab 26H x 21W x 24D with interior cargo netting and (2) adj shelves.
Rear cab wall storage cabinet with side access doors (one each side). Cabinet to be 50" high x 32" wide x 24" deep. Includes (2) roll‐up doors (satin finish) and (3) adjustable shelves. Lower door openings raised to provide hand clearance.
Non‐standard cargo net restraints. Restraints to be [#LOC].
Medical cabinet mounted on the officer side rear cab wall 55(54 as required)X20X22 with a locking satin finish roll‐up door and (3) adjustable shelves. Includes lower area raised to accomodate rear wall heater.
Medical cabinet mounted on rear wall of cab 40 x 36 x 18 with locking roll up door. Lower door opening raised to provide hand clearance.
Interior medical cabinet. Locate to rear of engine cover. Cabinet to be 30" high x 38" wide x 20" deep with a locking roll up door. Includes forward facing drop down door.
Compartment rear side of cab. Approx 22W x 36H opening. Includes double pan hinged door. Location: driver and officer side.
Compartment rear side of cab contents. Transverse portion under rear cab riser shall include the following storage solution accessible from both side cab compartment doors: rearward shall be four (4) tubes for storage of broom handles. The open remaining area in the transverse forward of the handle tubes on both sides shall feature a vertical formed sanded finish aluminum .125 partition that will create a storage cubby 30in. deep from the edge of the cab inner sub‐floor inboard into transverse accessible from either side cab compartment door.
ALS ‐ Side access. Includes compts on each side of cab, strikers high and low on ALS doors, access plts on int panel of ALS doors, extended cab floors, smooth plate rear kick plates, one adj shelf and nylatron floor overlay. Includes pass‐thru under bench seat if equipped.
Medical cabinet mounted on rear wall of cab full height x 38 x 26 with a locking roll up door. Lower door opening raised to provide hand clearance.
ALS ‐ Side access. Includes compts on each side of cab, strikers high and low on exterior doors, access plts on int panel of exterior doors, satin finish ROM roll‐up doors on interior and three adj shelves. Includes pass‐thru under bench seat (if equipped).
$2,686.00
$2,683.00
$2,683.00
$3,426.00
$3,201.00
$4,516.00
$2,108.00
$2,408.00
$3,289.00
$268.00
$2,860.00
$4,246.00
$3,369.00
$2,260.00
$755.00
$3,759.00
$4,516.00
$5,739.00
Option No.
1535‐0363
1535‐0364
1535‐0365
1535‐0366
1535‐0367
1535‐0368
1535‐0369
1535‐0370
1535‐0371
1535‐0372
1535‐0373
1535‐0374
1535‐0375
1535‐0376
1535‐0377
1535‐0378
1535‐0379
1535‐0380
Description
Cargo net for inside compartment. Net to permanently fasten on rearward wall just inside the exterior door opening and fasten with buckle straps on forward wall just inside the exterior door opening. Cargo netting will be approximately 2" x 2" squares. Location: wheel well medical cabinet.
ALS ‐ Side access. Includes compts on each side of cab with full height doors, strikers high and low on ALS doors, access plts on int panel of ALS doors with Tri‐Mark D‐Paddle latches, extended cab floors, smooth plate rear kick plates and two adj shelves. Includes pass‐thru under bench seat if equipped.
Driver side cab wheel well medical cabinet approximately 42 x 24 (25 Quest) x 26. Includes external locking roll‐up door and interior cargo net access. Cabinet includes (2) adjustable shelves. Note: Special cabinet 2" shorter front to rear (rear wall moved forward).
Rear cab wall medical cabinet with side access doors (one each side). Cabinet to be 56" high x 38" wide x 24" deep. Includes (2) locking roll‐up doors (satin finish) and (3) adjustable shelves. Lower door openings raised to provide hand clearance.
Louvers for vista medical cabinet. Locate louvers on lift‐up doors.
All interior access RUD for medical cabinets to be painted job color.
Rear cab wall medical cabinet with side access doors (one each side). Cabinet to be 56" high x 38" wide x 29" deep. Includes (2) locking roll‐up doors (satin finish) and (2) adjustable shelves. Lower door openings raised to provide hand clearance.
Driver side cab wheel well medical cabinet approximately 42x22(25 Quest)x28. Includes external locking pan door painted job color and interior cargo net. Cabinet includes (2) adjustable shelves with 3x3 tapered interior corner.
Officer side cab wheel well medical cabinet approximately 42x22(25 Quest)x28. Includes external locking pan door painted job color and interior cargo net. Cabinet includes (2) adjustable shelves with 3x3 tapered interior corner.
Rear cab wall medical cabinet with side access doors (one each side). Cabinet to be 54" high x 38" wide x 29" deep. Includes (2) locking roll‐up doors (satin finish) and (2) adjustable shelves. Lower door openings raised to provide hand clearance.
Cabinet mounted on rear wall of cab 55 x 40 x 20 with cargo net on forward opening. Includes clip restraints.
Driver side cab wheel well medical cabinet approximately 26 x 24 (27 Quest) x 28. Includes external locking pan door painted job color and interior cargo net.
Officer side cab wheel well medical cabinet approximately 42x24(27 Quest)x28. Includes external locking pan door painted job color and interior cargo net. Cabinet includes (1) adjustable shelf.
Medical cabinet mounted on rear wall of cab 62 x 38 x 20 with a locking roll up door. Lower door opening raised to provide hand clearance.
Interior medical cabinet. Locate to rear of engine cover. Cabinet to be 21" H x 45" W x 22" D. Cabinet to include a permanent shelf 4" from top, side to side divider on shelf centered, forward facing drop down door at shelf level and cargo net style cover over rear opening. Interior to be DA finish.
Medical cabinet mounted on the driver side rear cab wall FHX20X22 with a locking satin finish roll‐up door and (3) adjustable shelves. Includes lower area raised to accomodate rear wall heater.
Medical cabinet mounted on the officer side rear cab wall FHX20X22 with a locking satin finish roll‐up door and (3) adjustable shelves. Includes lower area raised to accomodate rear wall heater.
Driver side cab wheel well medical cabinet approximately 42x22(25 Quest)x28. Includes external pan door painted job color(s) with black locking Tri‐Mark latch and interior full height opening with cargo net cover. Cabinet includes (2) adjustable shelves.
PRICE
$865.00
$4,568.00
$2,236.00
$3,396.00
$369.00
$271.00
$3,396.00
$2,954.00
$2,954.00
$3,396.00
$3,611.00
$2,883.00
$3,154.00
$3,611.00
$2,003.00
$2,990.00
$2,990.00
$2,954.00
Option No.
1535‐0381
1535‐0382
1535‐0383
1535‐0384
1535‐0385
1535‐0386
1535‐0387
1535‐0388
1535‐0389
1535‐0390
1535‐0393
1535‐0394
1535‐0395
1535‐0396
1535‐0397
Description
Officer side cab wheel well medical cabinet approximately 42x22(25 Quest)x28. Includes external pan door painted job color(s) with black locking Tri‐Mark latch and interior full height opening with cargo net cover. Cabinet includes (2) adjustable shelves.
Cabinet, rear cab wall medical cabinet with front and side access doors (one each side). Cabinet to be full height x 32" wide x 24" deep (do not notch for support bracket; customer to store backboard(s) above support channel behind cabinet). Includes (1) locking lower horizontally hinged plate door on front located below roll‐up door drums, (2) locking side roll‐up doors (satin finish) and (3) adjustable shelves. Lower door openings raised to provide hand clearance. Interior of roll‐up door storage areas to have cabinet floor raised 1/4" above floor mounted roll up door frame/sill to accommodate smooth & non‐obstructed loading.
Officer side cab wheel well medical cabinet approximately 26 x 24 (27 Quest) x 28. Includes external locking pan door painted job color and interior cargo net.
Medical cabinet mounted on the wheel well officer side of cab 39H x 21W x 24D with a interior full height opening with cargo net restraint.
Interior medical cabinet. Locate to rear of engine cover. Cabinet to be 21" H x 45" W x 22" D. Cabinet to include a permanent shelf 4" from top, side to side divider on shelf centered, forward facing drop down door at shelf level, (1) adjustable shelf in rear section and cargo net style cover over rear opening. Interior to be DA finish.
Upper forward vista area cabinet. Cabinet to be full width and height of vista area forward of rear cab doors. Includes cargo netting over each opening . Outboard compartments to be approx. 12" wide.
Driver side cab wheel well medical cabinet approximately 45 (interior) x 24 (27 Quest) x 28. Includes external locking pan door painted job color and interior hinged full height door with locking push‐button latch. Cabinet includes (2) adjustable shelves.
Officer side cab wheel well medical cabinet approximately 45 (interior) x 24 (27 Quest) x 28. Includes external locking pan door painted job color and interior hinged full height door with locking push‐button latch. Cabinet includes (2) adjustable shelves.
Driver side cab wheel well medical cabinet approximately 26 x 22 (25 Quest) x 28. Includes external locking pan door painted job color with Tri‐Mark latch. No interior access.
Officer side cab wheel well medical cabinet approximately 26 x 22 (25 Quest) x 28. Includes external locking pan door painted job color with Tri‐Mark latch. No interior access.
Driver side cab wheel well medical cabinet approximately 30 x 22 (25 Quest) x 28. Includes external locking pan door painted job color and interior overlapped hinged full height door swing open fully to engine cover with locking push‐button latch. Cabinet includes (2) adjustable shelves.
Officer side cab wheel well medical cabinet approximately 30 x 22 (25 Quest) x 28. Includes external locking pan door painted job color and interior overlapped hinged full height door swing open fully to engine cover with locking push‐button latch. Cabinet includes (2) adjustable shelves.
Officer side cab wheel well storage cabinet approximately 42x24x28. Includes external pan door painted job color and raised boxed interior roll‐up door with satin finish for a 42" opening. Cabinet includes (2) adjustable shelves. Requires vista cab roof and removal of side windows.
Officer side cab wheel well medical cabinet approximately 42x22(25 Quest)x28. Includes external locking pan door painted job color. No shelves provided.
Medical cabinet mounted on the officer side rear cab wall 55(54 as required)X24X12 with a locking roll up door. Lower door opening raised to provide hand clearance.
PRICE
$2,954.00
$4,961.00
$2,883.00
$2,308.00
$2,223.00
$3,201.00
$3,614.00
$3,614.00
$2,588.00
$2,588.00
$2,614.00
$2,614.00
$3,094.00
$2,326.00
$3,215.00
Option No.
1535‐0398
1535‐0399
1535‐0400
1535‐0401
1535‐0402
1535‐0403
1535‐0404
1540‐0001
1540‐0002
1540‐0003
1540‐0005
1540‐0006
1540‐0007
1540‐0008
1540‐0012
1540‐0013
1540‐0014
1540‐0015
1540‐0016
1540‐0017
1540‐0018
1540‐0019
1540‐0020
1540‐0021
1540‐0022
1540‐0023
1540‐0024
Description
Medical cabinet mounted on the driver side rear cab wall 55(54 as required)X24X12 with a locking roll up door. Lower door opening raised to provide hand clearance.
Cabinet mounted on rear wall of cab 55 x 38 x 20 with cargo net on forward opening. Includes clip restraints.
[#COL] Diamond Grade chevron "A" stripe on lower exterior medical cabinet door panels full height. Includes wheel well cabinet doors and doors behind rear cab doors (if equipped).
Compartment rear side of cab. Approx 9W x 36H opening. Includes double pan hinged door. Long cab with medium door location only. Location: driver and officer side.
Driver side rear cab compartment to include 8" diameter tube recessed 4" centered in floor. Officer side compartment to include entire floor recessed 4".
Broom handle storage in lower transverse (4). (1) in each corner of extended cab riser height transverse storage.
Rear cab wall medical cabinet with side access doors (one each side). Cabinet to be full height x 38" wide x 24" deep. Includes (2) locking roll‐up doors (satin finish) and (3) adjustable shelves. Lower door openings raised to provide hand clearance.
Map box dual storage
Center console with map storage box.
For Typhoon chassis only
Map Box Rectangular Tall
Map box suspended with drop‐down doors.
Map Box with Angle Storage. Angled side to face officer.
Map box suspended with officer's map storage.
All map boxes in the cab to be painted OTO gray
All map boxes in the cab to be painted Zolatone 20‐64 gray.
All map boxes in the cab to be swirled with clear coat
Map box suspended with drop‐down door. Box offset to rear to allow engine access door to open further.
Map box suspended with officer front drop down door with (4) slots and driver rear drop down door with (4) slots.
Map box with angled top on rear of engine cover. Includes lift up door with gas shock.
Map Suspended with Officer's Map Storage. (6) storage slots for 4" binders, (1) additional storage slot for county custom map book.
Map boxes (2) shall be provided. Each with Zolatone gray finish. One box located between officer and driver. Second box located in the crew area between the communications boxes.
Map box with 3 compartments on rear of engine cover. Forward compartment has angle lift‐up door with gas shocks. Rear of box has top and rear compartments with hinged doors.
Map box suspended 34" wide with (3) drop down doors.
Map / medical box on rear of engine cover. Officer's side front has map box w/drop down door. Rear has two compts w/vert hinged doors. Left side includes one adj shelf.
Map box suspended rear facing with drop down door. Box offset to rear to allow engine access door to open further.
Map / medical box on rear of engine cover. Front has 2 map boxes w/3 horz slots ea and drop down doors. Rear has 2 compts w/vert hinged doors.
PRICE
$3,215.00
$3,611.00
$632.00
$1,339.00
$602.00
$718.00
$3,989.00
$594.00
$1,431.00
$545.00
$557.00
$612.00
$528.00
$739.00
$0.00
$0.00
$612.00
$612.00
$727.00
$605.00
$739.00
$1,450.00
$1,238.00
$727.00
$2,243.00
$612.00
$2,499.00
Option No.
1540‐0025
1540‐0026
1540‐0027
1540‐0028
Description
Map box suspended with officer's map storage.
Locking map box door. Map box door to include a locking push‐button latch. Key type to be CH751.
Map box suspended with officer front drop down door with (4) slots and driver rear drop down door with (2) slots.
Map box suspended with full width lower storage and officer's map storage.
1540‐0029
Offset suspended map box to rear of vertical 3x3 extrusions and as low as possible. Front of map box flush with front of 3x3 uprights.
Map Box Rectangular. Front storage area with hinged lid and push button latch, to have (3) equal storage spaces. Center mounting area. Rear storage area with hinged lid and push button latch, to have (2) equal storage spaces.
Map Box Suspended with Drop Down Door 17H x 34W x 14D. Box offset to rear to allow engine access door to open further.
Map box suspended with driver's map storage.
Map Box located on rear of engine cover to be approx 45"L x 13.5" W x 11.5"D.
Map box suspended 37" wide with (3) drop down doors.
Rear engine cover rectangular map box 12H X 13.75W X 31L. Includes (3) slots driver, open center, (2) slots officer side and cargo net cover.
Storage box with hinged top with push‐button latch. Box to be mounted to rear of engine cover and to rear of map box (hinge to forward edge). Size: 27" h x 34" w x 12" d
Map box suspended with drop‐down doors, 15" H x 37.5" W x 14" D with (4) slots each side.
Storage box with sliding aluminum plate doors. The doors to be secured with a tethered push‐button ball pin fastener. Box to be mounted rear facing on rear of engine cover. Size: 27" H x 34" W x 12" D outside dimensions.
Map box / rear engine cover medical cabinet. Includes forward facing map box with 2 drop down doors and incorporated rear engine cover medical cabinet with roll‐up door.
Map box suspended with drop down doors. 34"W x 10"H x 12"D
Map box OCFA. Located in the crew area between the wheel wells on the upper engine cover rear of the 3X3.
Map box suspended with driver and officer front drop down door and officer rear drop down door. Includes (4) slots on officer side and map storage on driver side.
Floor Mounted Map Box Between Driver and Officer Seats of Commercial Chassis.
Map Box with Large Storage Area and Cargo Net Cover.
Map box rectangular with rear hinged door. 11"L (front to rear) x 20"W (side to side) x 6"D.
Map box binder storage approx. 13"H x 11"W x 4" front to back. Location: (1) each side on interior wall of medical cabinet walls. Includes lid with mechanical latch. To match cab interior color.
1540‐0030
1540‐0031
1540‐0032
1540‐0033
1540‐0034
1540‐0035
1540‐0036
1540‐0037
1540‐0038
1540‐0039
1540‐0040
1540‐0041
1540‐0042
1540‐0043
1540‐0044
1540‐0045
1540‐0046
1540‐0047
1540‐0048
1540‐0049
Map box with 3 compartments on rear of engine cover. 2 compartments on top will be hinged back to back. Forward compartment has lift‐up door with gas shocks. Rear of box has top and rear compartments with hinged doors. Lower compartment will be approx 7" high.
Rear engine cover storage box with cargo net cover. 44"W x 24"H x 14"D with rear facing opening.
Map box suspended with drop down doors. Driver door approx. 15.5"W, officer door approx. 19.5"W. 35"W x 11"H x 13.5"D. Includes (1) vertical partition 4" from officer side and (1) vertical partition 15.25" from driver side. Driver side and center sections to each have a horizontal shelf centered.
PRICE
$739.00
$86.00
$727.00
$739.00
$0.00
$528.00
$740.00
$739.00
$1,450.00
$727.00
$1,020.00
$471.00
$612.00
$1,406.00
$4,709.00
$612.00
$1,079.00
$848.00
$2,529.00
$1,431.00
$528.00
$579.00
$1,238.00
$1,136.00
$612.00
Option No.
1540‐0050
1540‐0051
1540‐0052
1540‐0053
1540‐0054
1540‐0055
1540‐0056
1540‐0057
1540‐0058
1540‐0059
1540‐0060
1540‐0061
1540‐0062
1540‐0063
1540‐0064
1540‐0065
1540‐0066
1540‐0067
1540‐0068
Description
Storage box with hinged top and push‐button latch. Box to be mounted on rear of engine cover (hinge to forward edge), angled same as upper engine cover. Size: 15"H x 35"W x 7"D. Quest cabs only.
Map box suspended with drop‐down doors. 34"W x 9.50"H x 12"D.
Auto Pulse storage box with hinged top and push‐button latch. Box to be mounted on floor rear of engine cover (hinge to forward edge), angled same as lower engine cover. Size: 12"H x 44"W x 8"D(bottom)/11"D(upper).
Rear lower engine cover mounted storage box. To be approx. 44" W x 8" H x 12" D. Includes (3) equally spaced dividers. Includes cargo net cover.
Map box with two (2) compartments on rear of engine cover. Upper compartment to have lift‐up door with one (1) hold‐open and latch. Lower compartment to have drop down door with latch (accessible from the rear of the box).
Offset suspended map box low as possible. Angles to be offset 3" from front face of map box and mounted rearward of 3x3 extrusions.
Rear engine cover rectangular map box angled to match upper and lower vertical engine cover. 11"H X 12"W (front to rear) X 42.5"L. Includes (6) storage slots approx. 14"L x 6"W with (3) retaining straps front to rear, (1) over each area.
Map box suspended with driver and officer front and rear drop down doors. Includes (4) slots on each side.
Map box (rear facing) between rear facing seats, mid‐engine only. 43.75"W x 24"H (25"H w/ angle used to make a lip around full parameter of top) x 21"D. Includes 3" x 7" notch on each side for 3x3's in back of map box, (1) perm shelf with 1" lip centered in map box, (4) Whelen model OSR00MCR red lights (1) in each area at opening, 1" lip around perimeter of map box and cargo net cover for rear facing opening.
Map box in cab between forward seats. Includes mounting area for traffic advisor (if optioned) and siren control head (other electrical items and switches will be located in standard locations), sanded finish with black top surface material and hinged area at rear with two storage slots.
Storage box with hinged top with push‐button latch. Box to be mounted to rear of engine cover and to rear of map box (hinge to forward edge). Size: 17H x 34W x 12D.
Map storage box constructed of 3/16" aluminum.
Map Box. Locate between the driver and officer. Box to have a sanded finish with a black top. Rear area to be hinged forward with a single push button latch (ref #655283). Re‐locate the NFPA siren and switches to the map (the standard locations for the dash for these items will have cover plates installed).The multi‐plex screen is to remain dash area mounted
Map box suspended with (9) vertical slots.
Map box suspended with (9) vertical slots and (1) full width horizontal slot.
Map box suspended 37" wide with (3) drop down doors.
Map box suspended with officer's map storage. Includes (4) equal slots on officer side and (1) driver slot equal to top officer slot.
Map storage box constructed of 1/8" aluminum. Map Box will include forward area for switching, center area will have an area to mount sirens, radios, door adjar light and 12 volt power points, rear of this area will be a hinged door area for maps, and mounted to the rear of the box there will be a bracket to hold a 3 ring binder.
Storage box with hinged top with push‐button latch. Box to be mounted on the forward engine cover (hinge to forward edge). Size: 6"H x 20"W x 11"D(front to rear). Includes partition approx. 5.75" from driver side. Box to match cab interior.
PRICE
$471.00
$612.00
$612.00
$1,020.00
$1,238.00
$0.00
$1,020.00
$848.00
$2,055.00
$2,172.00
$471.00
$1,547.00
$3,126.00
$739.00
$848.00
$841.00
$739.00
$1,547.00
$471.00
Option No.
1540‐0069
1540‐0070
1540‐0071
1540‐0072
1540‐0073
1540‐0074
1540‐0075
1540‐0076
1540‐0077
1540‐0078
1540‐0079
1540‐0080
1540‐0081
1540‐0082
1540‐0083
1540‐0084
1540‐0085
1540‐0086
1540‐0087
1540‐0088
1540‐0089
Description
Map box suspended 34"W x 6"H x 12"D with driver and officer front and rear drop down doors. Includes (2) slots on each side. Locate just below AC.
Rear lower engine cover mounted storage box. To be approx. 44" W x 12" H x 12" D. Includes (1) center side to side divider with bungee cord cargo net cover.
Map box suspended with (1) drop down door. 14"W x 9.5"H x 12"D
Map Box with Angle Storage. Angled side to face officer. Includes single divider between angle storage and deep storage. Located on forward engine cover.
Map box suspended with drop‐down doors and (1) shelf each side. 34"W x 9.50"H x 12"D.
Map storage box constructed of 1/8" aluminum. Map Box will include forward area for switching, center area will have an area to mount sirens, radios and other miscellanous items. Rear of this area will be a hinged door area for maps.
Map box suspended with drop down doors. 34"W x 6"H x 13.5"D
Map box made from 1/16" aluminum diamond plate shall be mounted the floor centered behind the console. The map box shall be bolted in place and straddle the floor`s electrical access pane. The map box shall provide a slotted area to allow clearance to the access panel without removal of the map box.
Rear storage box on rear engine cover. Open box with forward hinged diamond plate lid and push‐button latches. Box size shall be 44" wide X 12" deep X 8" high.
All map boxes in the cab to be painted Zolatone "Dark Red" 20‐78.
Map box suspended with drop‐down doors. Approximately 34"W x 9.50"H x 13"D.
Map box suspended with drop‐down door installed on the rear of the box to provide accessibility from the rear. Box offset to rear to allow engine access door to open further.
Rear engine cover rectangular map box approximately 10"H X 14"W X 14"D. The depth shall have (2) dividers equally spaced. Open top with cargo net cover.
Map box suspended with drop‐down doors. 34"W x 9.50"H x 12"D. (3) Slot officer's side, open driver's side.
Map box rear facing. Lids only to be swirl plated with clear coat. Reference 581402.
Rear engine cover rectangular map box approximately 8.125"H (top to bottom) X 26"W (side to side) X 6.875"D (front to rear). The map box shall mount on the rear of the engine cover, on the lower horizontal surface at rear. The depth (front to rear) shall have (1) divider going from side to side, 2.5" from the rear to provide a front and rear compartment. The width (side to side) shall be divided equally going front to rear to provide (4) compartments. There shall be 3 open top radio boxes mounted to the rear lower of the map box. Each radio box will be 3.25" H X 3.25"W X 2.125" D. Radio boxes shall be mounted (2) 1" inboard each side and (1) centered at base of map box. Open top with cargo net cover. See layout in shop order file.
Map box suspended with drop‐down doors and (1) shelf each side. Box offset to rear to allow engine access door to open further.
Map box suspended with rear facing sliding Lexan doors, 15" H x 34" W x 12" D. Includes center partition and officer side shelf centered.
Map box suspended with officer's map storage with quarter latches.
All map boxes in the cab to be sanded finish.
Map box/radio cabinet suspended with drop‐down doors 34x14x12. Includes louvers on officer side lower door, side wall and floor. Box offset to rear to allow engine access door to open further.
PRICE
$848.00
$1,020.00
$568.00
$528.00
$612.00
$1,547.00
$612.00
$100.00
$612.00
$0.00
$839.00
$612.00
$471.00
$612.00
$1,217.00
$642.00
$612.00
$740.00
$739.00
$0.00
$891.00
Option No.
1540‐0090
1540‐0091
1540‐0092
1540‐0093
1540‐0094
1540‐0095
1540‐0096
1540‐0097
1540‐0098
1540‐0099
1540‐0100
1540‐0101
1540‐0102
1540‐0103
1540‐0104
1540‐0105
1540‐0106
1540‐0107
1540‐0108
1540‐0109
1540‐0110
Description
Map box suspended with drop‐down doors. Includes center vertical divider only.
Map box suspended with drop‐down doors and (1) shelf each side. 24"W x 9.50"H x 12"D.
Map box binder storage approx. 13"H x 11"W x 4" front to back. Location: on interior facing wall of officer side medical cabinet offset as far forward as possible toward 3x3 post. Includes lid with mechanical latch. To match cab interior color.
Map box suspended with drop‐down doors. Includes (1) adjustable shelf (no partition). Box offset to rear to allow engine access door to open further.
Map box suspended with rear facing drop‐down doors and (1) shelf each side. 34"W x 9.50"H x 12"D.
Map box suspended with (1) drop‐down door, (1) full width 2" high upper shelf, center lower vertical divider and (1) shelf each side of divider. 34"W x 9.50"H x 12"D.
Map box suspended with drop‐down doors, 15" H x 37.5" W x 14" D with (3) slots officer and (2) slots driver.
All map boxes in the cab to be painted Zolatone 20‐64 gray exterior and Zolatone white interior.
Map box suspended with driver and officer front drop down door and driver rear drop down door. Includes (3) slots on officer side and map storage on driver side.
Front center storage box between driver and officer seats 28"W x 47.5L" x 12.75" H. Includes double hinged lids, personal item storage areas 2 cup holders and 6 map pockets.
Map box suspended with drop down doors. 34"W x 6"H x 13.5"D. (1) officer shelf only.
The center console shall have an adjustable track mounted to the front of the console for joystick control mounting bracket.
Map box suspended with drop‐down doors. 37.5"W x 9.50"H x 12"D. (2) Slot officer's side, open driver's side.
Map box suspended with drop down doors. 34"W x 6"H x 12.5"D. Includes full width upper shelf and lower vertical divider.
Map box suspended with drop‐down doors, 15" H x 37.5" W x 14" D with center divider.
Map Box, custom for Renton. Box size approx. 20" wide x 24" long x 12" tall. Box design to accommodate 10 equal sized spaces approx. 3.75" wide x 11.5" long x 11.5" tall. Includes: lid hinged to rear with latch. Ref photo on file for Renton. Finish: sanded aluminum unless otherwise specified.
Box, aluminum 20W x 12T x MAX length front to rear as space provides. Includes: hinged lid with hinge located aft and black thumb style lever latch for access. Finish is sanded aluminum. Locate: rear of cab center console with top flush with top of console.
Storage Box/Map box. Construction: 1/8 in. smooth aluminum. Overall size 38 in. wide x 19 in. tall x 33 in. deep. Map box is to have separate storage area on forward portion approx 38 wide x 12 tall x 7 deep with black cargo net on top and snap fasteners. The rearward portion is approx 38 wide x 19 tall x 26 deep and includes a lift‐up smooth plate access door with (2) thumb latches & gas shock hold open device. The rear access door is to be held back 10 in. from forward box. Finish: paint to match cab interior. See drawing on file. Locate: In cab on engine cover between 3x3 posts.
Center console with map storage box.
Map box rectangular, rear facing on rear engine cover. The compartment shall be flush with the rear edge of the engine cover. Size: 14D X 30T X 36W. Includes: full height vertical divider 18 inches from driver side, one (1) adjustable shelf on the officer side of divider & a web cargo net with 2 inch square openings across the entire rear opening secured with small buckles on all sides. Construction is smooth aluminum with a match cab interior finish.
Map box on engine cover access door. 12W x 25L x 8D with (6) equal slots for 4" binders. Includes retaining strap on top. Finish to match cab interior.
PRICE
$612.00
$612.00
$290.00
$612.00
$612.00
$612.00
$612.00
$0.00
$848.00
$2,298.00
$612.00
$203.00
$612.00
$725.00
$612.00
$2,273.00
$683.00
$1,545.00
$1,431.00
$1,265.00
$572.00
Option No.
1540‐0111
1540‐0112
1540‐0113
1550‐0000
1550‐0001
1550‐0002
1550‐0003
1550‐0004
1550‐0005
1550‐0006
1550‐0007
1550‐0008
1550‐0009
1550‐0010
Description
Map box suspended with drop‐down doors. 37.5"W x 9.50"H x 12"D. (2) Slot officer's side, (3) slot driver's side.
Center map storage box for commercial cab.
Storage box with cargo net top. Box to be mounted to rear of engine cover and to rear of map box. Size: 9H x 34W x 12D.
Map pockets cab front doors ABS.
Map pockets cab front doors diamond plate
Map pockets cab front doors stainless steel.
Rear crew cab doors in the medium position.
Rear crew cab doors in the long position. Not available on medium cabs.
Driver and officer cab door windows. Include forward vent windows.
Driver and officer cab door windows. Include rear fixed window.
All cab exterior access doors to have CH751 keyed locks.
Fixed rear cab wall windows (pr). Not available with side mount pump module applications.
Fixed rear cab wall narrow windows (pr).
Sliding rear cab wall windows (pr). Windows are drop style and not available with side mount pump module applications.
1550‐0011
Rear crew cab door windows. Includes manual roll‐down actuation. Not available on Typhoon or CII with paddle style door latching.
Driver and Officer door windows. Includes electric roll‐down actuation. Each door to have individual control at door position and the driver door is to have master control for all power window locations.
Rear crew cab door windows. Includes electric roll‐down actuation. Each door to have individual control. Not available with paddle style door latching.
Stainless steel protective trim on rear edge of cab door openings. E‐ONE custom chassis only.
Cab door panels ABS.
Cab door panels stainless steel.
Scuff plates stainless steel (Set). Not available with paddle latches.
Windows cab side sliding driver side.
Windows cab side fixed driver's side.
Cab roof vent with fan (pair). Each vent switched next to vent. Location: (1) each side centered above rear cab doors.
Windows rear sliding vista. Requires raised roof option
All cab doors shall have exterior paddle latches.
All cab doors shall have "L" style exterior latches.
Map pockets cab rear doors ABS.
Front cab door windows to have manual actuation.
Map pockets cab rear doors diamond plate
Map pockets cab rear doors, stainless steel.
Windows cab side sliding officer side.
Windows cab side fixed officer's side.
The rear cab door windows shall be fore and aft sliding type.
1550‐0013
1550‐0014
1550‐0015
1550‐0016
1550‐0017
1550‐0018
1550‐0019
1550‐0020
1550‐0022
1550‐0023
1550‐0024
1550‐0025
1550‐0026
1550‐0027
1550‐0029
1550‐0030
1550‐0032
1550‐0033
1550‐0034
PRICE
$612.00
$1,431.00
$471.00
$0.00
$200.00
$164.00
$0.00
$0.00
$0.00
$0.00
$197.00
$129.00
$126.00
$287.00
$0.00
$1,627.00
$1,627.00
$249.00
$0.00
$1,452.00
$116.00
$293.00
$0.00
$889.00
$483.00
$678.00
$0.00
$0.00
$0.00
$171.00
$208.00
$293.00
$0.00
$0.00
PRICE
$0.00
$0.00
$171.00
$674.00
$171.00
$405.00
$171.00
$405.00
$332.00
$0.00
$695.00
$100.00
$163.00
$291.00
$2,006.00
$363.00
$629.00
1550‐0061
1550‐0063
Description
No window on the driver side of the cab
No window on the officer side of the cab.
(4) Incandescent cab step area lighting. Locate each light in [#LOC]. Lights to be switched with door ajar.
(4) LED cab step area lighting. Locate each light [#LOC]. Lights to be switched with door ajar.
Door mounted red incandescent flashing lights (4). Locate lights [#LOC]. Lights to be switched with door ajar.
Door mounted red LED flashing lights (4). Locate lights [#LOC]. Lights to be switched with door ajar.
Door mounted amber incandescent flashing lights (4). Locate lights [#LOC]. Lights to be switched with door ajar.
Door mounted amber LED flashing lights. Locate lights [#LOC]. Lights to be switched with door ajar.
All cab door kick plates to be made from smooth plate aluminum with DA finish.
All cab door kick plates to be made from diamond plate aluminum.
All cab door kick plates to be made from stainless steel plate.
Canadian flag reflective material in place of striping for interior cab doors.
All (4) cab doors to have double strap. Straps to be sewn together.
All cab exterior cab locks to be keyed for #CH751 locks. Orange County.
Federal LED Delta Ray amber/red warning lights, bottom of cab doors (interior), wired to door switches.
Aluminum interior rear cab door handrails (PR) IPOS.
All cab exterior access doors to have 1250 keyed locks.
Door mounted Whelen 500 series red TIR6 LED flashing lights (4) w/clear lenses. Locate lights [#LOC]. Lights to be switched with door ajar.
Cab door insert (ea) ‐ Carbon fiber style. Quest cab only.
Cab door insert (ea), stainless steel. Quest cab only.
Matching keys for Cab doors and all roll‐up compartment access doors.
Reflective [#COL] printed striping positioned in the "A" formation located on the cab door panels.
Reflective [#COL] striping positioned in the "V" formation located in the lower cab door panels
Rear crew cab door window. Includes electric roll‐down actuation. Not available with paddle style door latching. For use with 3 door cab only.
(3) LED cab step area lighting. Locate each light in [#LOC]. Lights to be switched with door ajar.
1550‐0064
1550‐0065
1550‐0066
1550‐0067
1550‐0068
1550‐0069
1550‐0070
1550‐0071
1550‐0072
Rear crew cab door window. Includes manual roll‐down actuation. Not available with paddle style door latching. 3 door custom cab only.
(3) Incandescent cab step area lighting. Locate each light in [#LOC]. Lights to be switched with door ajar.
Cab door kickplates fastened with screws.
[#COL] chevron "V" stripe on lower cab door panel approx 18" high. Stainless steel door panels only. CIIX and TyphoonX only.
Chrome grab handles on front cab doors (additional) (PR). Locate (1) each side below windows towards rear of doors.
Reflective [#COL] 3M Diamond Grade striping positioned in the "A" formation located on the cab door panels.
All (4) cab doors to have double door straps. Straps to be long enough to allow the door to open to a max of 90 degrees.
ABS cab door panels and lower kick panels to be fastened with screws. No drive rivets.
Cab door panels aluminum painted Zolatone gray.
$590.00
$131.00
$258.00
$321.00
$121.00
$326.00
$322.00
$429.00
$1,452.00
Option No.
1550‐0035
1550‐0036
1550‐0037
1550‐0038
1550‐0039
1550‐0040
1550‐0041
1550‐0042
1550‐0043
1550‐0044
1550‐0045
1550‐0046
1550‐0047
1550‐0050
1550‐0052
1550‐0053
1550‐0054
1550‐0055
1550‐0056
1550‐0057
1550‐0058
1550‐0059
1550‐0060
$1,353.00
$253.00
$370.00
$629.00
$0.00
$0.00
$817.00
$506.00
Option No.
1550‐0073
1550‐0074
1550‐0075
1550‐0076
1550‐0077
1550‐0078
1550‐0079
1550‐0080
1550‐0081
1550‐0082
1550‐0083
1550‐0084
1550‐0085
1550‐0086
1550‐0087
1550‐0088
1550‐0089
1550‐0090
1550‐0091
1550‐0092
1550‐0093
1550‐0094
1550‐0095
Description
[#COL] chevron "A" printed stripe on lower cab door panel approx 18" high. Stainless steel/painted door panels only. CIIX and TyphoonX only.
PRICE
$321.00
[#COL] chevron "A" stripe on entire lower cab door kick plate. Stainless steel or smooth plate kick plates only. CIIX and TyphoonX only.
Door mounted red LED flashing lights (3). Locate lights [#LOC]. Lights to be switched with door ajar.
NFPA Required reflective striping on cab doors to be dealer/customer applied.
Interior cab door locks ‐ manual. Will have manual actuation from each respective door. Includes barrel style key lock on each exterior cab door.
Map pockets 14 gauge stainless steel. Includes vinyl trim around top of opening and nylon strap with snap to retain contents. Location: front cab doors.
Guard, rubrail with endcaps for cab door strip lights.
$321.00
$305.00
$0.00
[#COL] chevron "A" printed stripe on lower cab door panel approx 12" high. Stainless steel door panels only. CIIX and TyphoonX only.
Cab door locks ‐ electric. Includes driver side exterior touchpad, (2) remote key fobs, barrel style key lock on exterior of each door and manual interior lock on each door.
(2) LED cab step area lighting. Locate each light in on each cab door in the inboard position. Lights to be switched with door ajar.
All cab exterior access doors to have CH751 keyed locks.
All cab exterior access doors to have 1250 keyed locks.
All cab exterior access doors to have J236 keyed locks.
Door mounted red LED flashing lights (2). Locate lights [#LOC]. Lights to be switched with door ajar.
[#COL] Diamond Grade chevron "A" stripe on lower cab door panel approx 12" high. Stainless steel/painted door panels only. TyphoonX, CIIX and QST2 only.
[#COL] chevron 2" "A" stripe on lower cab door panel approx 12" high. Stainless steel door panels only. CIIX and TyphoonX only.
Four (4) cab doors with non‐locking "L" style latches. For use with a flat roof cab. Includes front door windows with front vent, rear door roll‐down windows, and (4) interior surface mounted reflective sign plates. Custom ES.
Four (4) cab doors with locking "L" style latches (CH751). For use with a flat roof cab. Includes front door windows with front vent, rear door roll‐down windows, and (4) interior surface mounted reflective sign plates. Custom ES.
Four (4) cab doors with non‐locking "L" style latches. For use with a 12" vista roof cab. Includes front door windows with front vent, rear door roll‐down windows, and (4) interior surface mounted reflective sign plates. Custom ES.
Four (4) cab doors with locking "L" style latches (CH751). For use with a 12" vista roof cab. Includes front door windows with front vent, rear door roll‐down windows, and (4) interior surface mounted reflective sign plates. Custom ES.
Four (4) cab doors with "L" style latches and interior / exterior locks (1250 key). For use with a flat roof cab. Includes front door windows with front vent, rear door roll‐down windows, and (4) interior surface mounted reflective sign plates. Custom ES.
Four (4) cab doors with "L" style latches and interior / exterior locks (1250 key). For use with a 12" vista roof cab. Includes front door windows with front vent, rear door roll‐down windows, and (4) interior surface mounted reflective sign plates. Custom ES.
One touch down operation for cab door electric windows.
$321.00
$0.00
$440.00
$427.00
$1,292.00
$337.00
$0.00
$0.00
$629.00
$204.00
$532.00
$321.00
$0.00
$53.00
$0.00
$53.00
$0.00
$0.00
$2,735.00
Option No.
1550‐0096
1550‐0097
1550‐0098
1550‐0099
1550‐0100
1550‐0101
1550‐0102
1550‐0103
1550‐0104
1550‐0105
1550‐0106
1550‐0107
1550‐0108
1550‐0109
1550‐0110
1550‐0111
1550‐0112
1550‐0113
1550‐0114
1550‐0115
1550‐0116
1550‐0117
1550‐0118
1550‐0119
1550‐0120
1550‐0121
1550‐0122
1550‐0123
1550‐0125
Description
Door mounted Whelen amber M6AC LED flashing lights (4) w/clear lenses. Lights to alternate flash top and bottom on each light. Locate lights [#LOC]. Lights to be switched with door ajar.
Nader pin guards on front cab doors.
Stainless steel protective trim on rear edge of cab door openings. E‐One Quest chassis only.
Scuff plates stainless steel (Set). Approx. 7"x7" to encompass door handle and lock. Not available with paddle latches.
Polished stainless steel protective trim on rear edge of cab door openings. E‐ONE custom chassis only.
Polished stainless steel scuff plates for exterior cab door handles (set). Not available with paddle latches.
Rear crew cab door windows with rear fixed panel. Includes electric roll‐down actuation. Each door to have individual controls. For use with paddle style door latching.
Rear crew cab door windows with rear fixed panel. Includes manual roll‐down actuation. For use with paddle style door latching.
Alternating reflective Red and Yellow striping (chevron), positioned on the cab door interior angling down and away from truck.
Reflective [#COL] striping positioned in the "A" formation located on the lower cab door stainless steel panels. Striping to cover the lower 14" of each door.
[#COL] chevron "A" stripe on lower cab door panel approx 24" high. Stainless steel door panels only. CIIX and TyphoonX only.
[#COL] chevron "A" stripe on lower cab door panel approx 6" high. Stainless steel door panels only. CIIX and TyphoonX only.
Stainless steel protective trim on rear edge of rear cab door openings. E‐ONE custom chassis only.
[#COL] Diamond Grade chevron "A" stripe on lower cab door panel approx 18" high. Stainless steel/painted door panels only. TyphoonX, CIIX and QST2 only.
Warning light Federal Signal Viper EXT Model VPX802‐4 LED w/ bezel (PR). Surfaced mounted with red lens. Location: (1) each side on driver and officer door outboard. Lights to be switched with door ajar.
Interior cab door window trim to be stainless steel. Requires stainless steel door panels.
Window film Dupont anti‐spall. Location: front cab doors.
Cab door panels 12Ga stainless steel.
Map pockets cab front doors aluminum plate painted Zolatone gray.
Map pockets cab rear doors aluminum plate painted Zolatone gray.
Cab door locks ‐ electric; 2DR cab only. Includes driver side exterior touchpad, (2) remote key fobs, barrel style key lock on exterior of each door and manual interior lock on each door.
Scuff plates stainless steel (PR) door lock. For use with paddle latches.
(2) LED cab step area lighting. Locate each light in the cab step well area. Lights to be switched with door ajar.
Reflective striping on cab doors to be dealer provided and installed.
Door panels cab alum painted Zolatone black.
Cab door strap one (1) additional to standard straps shall be provided. Location: One (1) each cab door.
Locate interior cab door handles per Engineering print. Rear cab door grab handles on angle.
Four (4) cab doors with "L" style latches and interior / exterior locks (1250 key). For use with a 12" vista roof cab. Includes front door windows with front vent, rear door electric windows, and (4) interior surface mounted reflective sign plates. Custom ES.
Chrome grab handles on front of cab (additional) (PR). Locate (1) each side below winshields outboard of wiper pivot points.
PRICE
$1,451.00
$147.00
$249.00
$250.00
$276.00
$120.00
$1,825.00
$197.00
$0.00
$0.00
$321.00
$229.00
$125.00
$532.00
$594.00
$434.00
$175.00
$1,452.00
$187.00
$187.00
$999.00
$60.00
$337.00
$0.00
$1,452.00
$157.00
$0.00
$0.00
$121.00
Option No.
1550‐0126
1550‐0127
1550‐0128
1550‐0129
1550‐0130
1550‐0131
1550‐0132
1550‐0133
1550‐0134
1550‐0135
1550‐0136
1550‐0137
1550‐0138
1550‐0139
1550‐0140
1550‐0141
1550‐0142
1550‐0143
1550‐0144
1550‐0145
1550‐0146
1550‐0147
1550‐0148
Description
Reflective [#COL] 3M Diamond Grade striping positioned in the "A" formation located in the lower cab door panels, extending approximately 18" from the door's bottom.
Door mounted Whelen M4RC LED flashing lights (4) w/clear lenses. Locate lights [#LOC]. Lights to be switched with door ajar.
(4) Whelen LED cab step area lighting. Locate each light [#LOC]. Lights to be switched with door ajar.
Enclosures for electric door window actuation switch(s) shall be stream lined, (1) switch behind another (not side by side) mounted in an enclosure to match the door's interior IPOS. Each door to be individually controlled. The driver shall have control for all electrically actuated windows.
Stainless steel protective trim on rear edge of rear ALS cab door openings. E‐ONE custom chassis only.
Removable access panel on each cab door to the regulator and latch.
Driver and Officer door windows. Includes electric roll‐down actuation. Each window to be individually controlled at each door. Each window switch will be flush mounted as far forward on the door as possible with minimal or no switch mounting protrusion. The driver side will NOT have controls for all electrically actuated windows but rather a single switch for the driver door window only.
Stainless steel trim on bottom edge of the over wheel cab compartment opening (ea).
Polished stainless steel trim on bottom edge of the over wheel cab compartment opening (ea).
Stainless steel trim on the vertical edge of the over wheel cab compartment opening (ea).
Polished stainless steel trim on the vertical edge of the over wheel cab compartment opening (ea).
A removable access panel shall be incorporated into the interior cover panel(s) of each cab door to permit easy access to the latch mechanism.
Door mounted Whelen M2 red super LED flashing lights (4). Locate lights on each cab door in the outboard position. Each individual light shall be activated by the corresponding cab door ajar circuit.
Each cab door shall have stainless steel trim on the trailing edge of the door to include forward door wheel well (radius) area. E‐ONE custom chassis only.
Reflective [#COL] 3M Diamond Grade striping positioned in the "A" formation located in the lower cab door panels, extending approximately 14" from the door's bottom.
Polished stainless steel protective trim to wrap cab door jambs on all (4) entry doors. Trim to extend 3" past closed door edge (as applicable). E‐One custom chassis only.
The cab door inserts shall have the fastening hardware upgraded to nutserts and stainless steel hardware IPOS.
Reflective [#COL] 3M Diamond Grade striping positioned on the upper SS insert IPO lower door area.
Reflective [#COL] individual striping positioned in the "A" formation located on the cab door panels.
[#COL] chevron "A" individual stripes on lower cab door panel approx 18" high. Stainless steel/painted door panels only. CIIX and TyphoonX only.
[#COL] chevron "A" individual stripe on lower cab door panel approx 12" high. Stainless steel/painted door panels only. CIIX and TyphoonX only.
Location ‐ Front door map pockets shall be located approximately 17" below window.
Reflective [#COL] 3M Diamond Grade striping positioned in the "A" formation located in the lower cab door panels, extending approximately 12" from the door's bottom.
PRICE
$488.00
$1,331.00
$874.00
$256.00
$125.00
$548.00
$1,854.00
$0.00
$39.00
$53.00
$70.00
$548.00
$1,190.00
$428.00
$380.00
$1,224.00
$63.00
$488.00
$236.00
$398.00
$357.00
$112.00
$359.00
Option No.
1550‐0149
1550‐0150
1550‐0151
1550‐0152
1550‐0153
1550‐0154
1550‐0155
1550‐0156
1550‐0159
1550‐0160
1550‐0161
1550‐0162
1550‐0163
1550‐0164
1550‐0165
1550‐0166
1550‐0167
1550‐0169
1550‐0170
1550‐0171
1550‐0172
1550‐0173
1550‐0174
Description
Cab door kick plates made from diamond plate aluminum shall be overlaid on top of the existing door panel (Zolatone, stainless steel etc). The kick plates shall be 16" in height.
Rear crew cab door windows with rear fixed panel. Includes electric roll‐down actuation. Each door to be individually controlled. Each window switch will be flush mounted below rearward fixed window area with minimal or no switch mounting protrusion. For use with paddle style door latching.
The map boxes attached to cab doors shall include press on black trim. The trim shall be applied along the edge of map box opening.
Window film Dupont anti‐spall. Location: front cab doors, canopy windows and rear cab doors.
Warning light Federal Signal Viper EXT Model VPX802‐4 LED w/ bezel (PR). Surfaced mounted with red lens. Location: (1) each side on driver and officer rear cab door outboard. Lights to be switched with door ajar.
Chrome edge guard on rear vertical edges of cab doors.
Rear crew cab door window with rear fixed panel. Includes electric roll‐down actuation. Door to be individually controlled. For use with paddle style door latching.
Cab door locks ‐ electric. Includes driver side exterior touchpad, (2) remote key fobs, barrel style key lock and manual interior lock on each door.
Interior cab door locks ‐ manual. Will be individually actuated from each respective door. Includes key lock on each exterior cab door handle. (QST2 only)
Cab door locks ‐ electric. Includes (2) remote key fobs, barrel style key lock on exterior of each door and manual interior lock on each door.
Warning light Whelen 500 Super LED (4) red model 50R03ZCR lights with clear lenses. Flashing lights wired through each individual door. Location: One on each of the interior cab doors (outboard position).
Door mounted Whelen 500 series amber TIR6 LED flashing lights (2) w/clear lenses. Locate lights on each cab door in the outboard position. Lights to be switched with door ajar.
Map pockets cab rear doors aluminum plate painted Zolatone black.
Driver and officer cab door windows. Includes manual regulators with HD cranks. (QST2 only)
Rear crew cab door windows. Includes manual regulators with HD cranks. (QST2 only)
Stainless steel protective trim on rear edge of cab door openings. Includes front cab door lower angle areas. E‐ONE custom chassis only.
Reflective Blue 3M Scotchlite and Fluorescent Yellow Green 3M Diamond Grade striping positioned in the "A" formation located in the lower cab door panels.
Cab door panels aluminum painted to match cab interior. (QST2 only)
Cab doors to open approximately 90 degrees.
(4) TecNiq LED cab step area lighting. Locate each light [#LOC]. Lights to be switched with door ajar.
Full width 6" reflective [#COL] striping positioned on the lower cab door panels
Stainless steel trim on bottom edge of the over wheel cab compartment opening (ea). Vertical trim edge to be 3" tall.
Reflective [#COL] 3M Diamond Grade striping positioned in the "A" formation located in the entire SS cab door panels below the windows.
PRICE
$220.00
$1,854.00
$85.00
$505.00
$594.00
$84.00
$914.00
$1,292.00
$0.00
$787.00
$1,272.00
$677.00
$187.00
$0.00
$0.00
$302.00
$326.00
$1,427.00
$0.00
$231.00
$0.00
$133.00
$999.00
Option No.
1550‐0175
1550‐0176
1550‐0177
1550‐0178
1550‐0179
1550‐0180
1550‐0181
1550‐0182
1550‐0183
1550‐0184
1550‐0185
1550‐0186
1550‐0188
1550‐0189
1550‐0190
1550‐0191
1550‐0192
1550‐0193
1550‐0194
1550‐0195
1550‐0196
1550‐0197
1550‐0199
1550‐0200
1550‐0201
1550‐0202
1550‐0203
1550‐0204
Description
Door mounted Whelen model 0SA00MCR LED flashing lights. Locate lights [#LOC]. Lights to be switched with door ajar.
Door mounted Whelen 3SR00FRR red super LED flashing lights (4). Locate lights [#LOC]. Each individual light shall be activated by the corresponding cab door ajar circuit.
[#COL] Reflexite V98 striping positioned in the "A" formation located on the cab door panels.
[#COL] Reflexite V98 chevron "A" stripe on lower cab door panel approx 12" high. Stainless steel/painted door panels only. TyphoonX, CIIX and QST2 only.
[#COL] Reflexite V98 chevron "A" stripe on lower cab door panel approx 18" high. Stainless steel/painted door panels only. TyphoonX, CIIX and QST2 only.
Cab door panels stainless steel. Includes upper and lower panels with seam below handrail.
[#COL] chevron "A" printed stripe on lower cab door panel below map pockets to bottom of door. Stainless steel/Zolatone door panels only.
Door mounted Federal Signal amber MPS600‐AA LED flashing lights (4) w/clear lenses. Locate lights [#LOC] . Lights to be switched with door ajar.
Recess in upper rear cab doors in lieu of windows (PR). (1) each side approx. 10L x 5W x 3D for latex glove box. Includes (2) velcro straps for each recess to be mounted at final inspection.
Map pockets cab front doors aluminum plate painted Zolatone black.
Cab door panels aluminum painted Zolatone gray. Includes upper and lower panels with seam below handrail.
(4) TecNiq T440 4" LED cab step area lighting. Locate each light [#LOC]. Lights to be switched with door ajar.
LINE‐X Door Panels: The inner cab door panels shall be made out of aluminum plate coated with LINE‐X for increased durability.
Map pocket officer cab front door aluminum plate painted Zolatone gray.
Warning light Whelen 500 Super LED (4) split red/amber model 50RA3ZCR lights. Flashing lights wired through each individual door. Location: One on each of the interior cab doors (outboard position).
Handle, grab. Cab door interior grab handle location modification. Locate interior cab door grab handles as far rearward as possable.
Additional remote key fob (PR).
[#COL] Reflexite V98 striping positioned in the "A" formation located in the entire SS cab door panels below the windows.
Cab door window trim mechanically fastened in place of standard.
All cab exterior access doors to have 1041 keyed locks.
(2) TecNiq T440 4" LED cab step area lighting. Locate each light [#LOC]. Lights to be switched with door ajar.
Map pockets on the cab front doors shall be aluminum plate painted LINE‐X. The LINE‐X color to match the interior of the cab.
Warning light Whelen 500 Super LED (4) amber model 5VA02ZAR vertical lights with 5FLANGEP mount. Flashing lights wired through each individual door. Location: One on each of the interior cab doors (outboard position) mounted vertically.
(4) Whelen 3" LED cab step area lighting. Locate each light [#LOC]. Lights to be switched with door ajar.
Door mounted Whelen ION amber LED flashing lights. Locate lights [#LOC]. Lights to be switched with door ajar.
Relocate driver master power window controls to driver lower cab dash adjacent to steering column.
Map pockets cab front doors stainless steel 1.5" deep.
Locate rear cab door ajar switches high on door hinges.
PRICE
$309.00
$770.00
$263.00
$363.00
$402.00
$1,666.00
$321.00
$961.00
$618.00
$187.00
$1,666.00
$231.00
$1,903.00
$94.00
$1,272.00
$361.00
$87.00
$804.00
$65.00
$0.00
$116.00
$373.00
$1,475.00
$644.00
$1,362.00
$433.00
$164.00
$106.00
PRICE
1550‐0210
Description
Polished stainless steel protective trim on rear edge of cab door openings. Includes front cab door lower angle areas. E‐ONE custom chassis only.
Cab door panels aluminum painted Zolatone "Dark Red" 20‐78.
Cab door locks ‐ electric. Includes driver and officer side exterior touchpads, (2) remote key fobs, barrel style key lock and manual interior lock on each door.
Relocate driver master power window controls to center cab dash.
Door mounted Whelen ION red LED flashing lights. Locate lights [#LOC]. Lights to be switched with door ajar.
Door mounted Power Arc model PP2‐RC red LED flashing lights (4) w/clear lenses. Locate lights [#LOC]. Lights to be switched with door ajar.
1550‐0211
1550‐0212
1550‐0213
1550‐0214
1550‐0215
Polished stainless steel trim on bottom edge of the over wheel cab compartment opening. Trim to span down to wheel well trim. (ea.)
Map pockets on the cab rear doors shall be aluminum plate painted LINE‐X. The LINE‐X color to match the interior of the cab.
Door mounted Whelen ION split red/amber LED flashing lights. Locate lights [#LOC]. Lights to be switched with door ajar.
Cab door panels swirled aluminum.
Rotate rear interior cab door paddle latches 90 degrees. Operator to pull up to open cab doors.
$289.00
$373.00
$1,362.00
$1,452.00
$250.00
1550‐0216
1610‐0000
1610‐0001
1610‐0002
1610‐0003
1610‐0004
Door mounted Whelen 400 red Super LED flashing lights with clear lenses (4). Locate lights [#LOC]. Lights to be switch with door ajar.
Cab and body to have applicable E‐ONE logos.
Logo package cab Saulsbury. Includes horn ring badge, center wheel decals and grille logo
Logo package cab Superior. Includes horn ring badge, center wheel decals and grille logo
Cab and body to have no logos.
Cab and body to have applicable E‐ONE logos installed without fasteners.
Vista cab 20" with extension for top mount pump panel controls. Includes 4" cap for additional headroom. Note: "Delete down view window" option required with full width pump module.
Vista full height rear doors, 12".
Vista full height rear doors 16".
Vista full height rear doors 20".
Cab roof to be "flat" with trough for waterway. Required with HM100 (with waterway), HP100 (all), CR100/92 Pltfm (SdStckr and W/O/P) or HP/HPS100 Pltfrm (all).
Delete front vista roof windows.
Delete side vista roof windows ahead of rear doors.
Delete rear vista roof windows.
Delete upper rear door vista roof windows
Cab roof to be "flat" (non‐vista).
Delete side vista roof windows rearward of rear doors.
Vista cab 20" with extension for top mount pump panel controls. Note: "Delete down view window" option required with full width pump module.
$1,028.00
$0.00
$0.00
$0.00
$0.00
$0.00
Option No.
1550‐0205
1550‐0206
1550‐0207
1550‐0208
1550‐0209
1615‐0000
1615‐0001
1615‐0002
1615‐0003
1615‐0004
1615‐0005
1615‐0006
1615‐0007
1615‐0009
1615‐0010
1615‐0012
1615‐0013
$302.00
$1,452.00
$1,482.00
$433.00
$1,362.00
$888.00
$11,352.00
$3,874.00
$4,056.00
$4,238.00
$0.00
$0.00
$0.00
$0.00
$0.00
$0.00
$0.00
$10,843.00
Option No.
1615‐0014
1615‐0015
1615‐0016
1615‐0017
1615‐0018
1615‐0019
1615‐0020
1615‐0021
1615‐0022
1615‐0023
1615‐0025
1615‐0026
1615‐0027
1615‐0028
1615‐0029
1615‐0030
1620‐0001
1620‐0002
1620‐0003
1620‐0004
1620‐0005
1620‐0006
1620‐0007
1620‐0008
1620‐0009
1620‐0010
1620‐0011
1640‐0000
1640‐0009
1640‐0010
1640‐0011
Description
Delete down view windows each side of enclosed top mount panel..
Diamond plate overlay (integral as applicable) front of vista slope.
Cab roof to have a 4.5" deep x 44" wide trough for lowered aerial.
Aerial windows shall be installed in place of standard cab roof.
Aerial windows shall be installed in place of standard cab roof.
Vista full height rear doors 20". Includes 4" cap for a 24" total raised roof.
Side vista roof windows behind rear doors. 80" cab with medium doors only.
Split raised rear cab roof. 12" high for use with rear mount aerial.
Cab roof to have 12" high split raised rear section with full length center waterway trough. For use with rear mount aerial.
Cab roof to have 12" high split raised rear section with full length center waterway trough. Inboard vertical surfaces tapered outward for use with HP100 Platform.
Cab roof to have a 4.5" deep x 44" wide trough with 1.5" deep side notches for lowered HP100 Platform.
Delete the rear center vista roof window.
Cab roof to have 12" high split raised rear section and a 4.5" deep x 44" wide trough for rear mount lowered aerial.
Delete driver side opera vista window.
Delete rear outboard vista roof windows.
Cab roof to be smooth plate painted job color in lieu of standard diamond plate construction.
ABS painted grille
Stainless steel grille for Typhoon X.
Stainless steel grille for Typhoon
ABS chrome plated grille.
PRICE
$0.00
$511.00
$609.00
$529.00
$508.00
$5,753.00
$129.00
$6,012.00
$6,012.00
Stainless steel grille for front of CIIX Hush/Mid engine. Iincludes modifications to lower area for required booster reel roller placement.
CIIX stainless steel grille for Typhoon X.
ABS chrome plated grille. Custom ES.
Stainless steel grille with oval E‐ONE logo for Quest (QST2 only).
Stainless steel grille with "E‐ONE" letters for Quest (QST2 only).
Ship cab grille E‐ONE loose.
Stainless steel grille w/o logo for Quest (QST2 only).
Step below cab door. Located [#LOC]. Steps under front cab doors shall not interfere with approach angle.
Steps below front cab door ‐ CFR swing style (PR). Includes plunger stop to hold in the down position. Step to be centered below cab step.
Diamond plate trim package for a (2) door International 4400. Includes driver and officer step trim that will utilize pieces already supplied by the OEM.
Diamond plate trim package for a (2) door International 7400 or 7600. Includes driver and officer step trim that will utilize pieces already supplied by the OEM.
$1,061.00
$961.00
$0.00
$0.00
$0.00
$0.00
$0.00
$248.00
$6,012.00
$757.00
$0.00
$6,619.00
$0.00
$0.00
$963.00
$0.00
$961.00
$961.00
$0.00
$1,005.00
$1,352.00
$1,352.00
Option No.
1640‐0016
1640‐0018
1640‐0020
1640‐0021
1640‐0022
1640‐0024
1640‐0025
1640‐0026
1640‐0027
1640‐0028
1640‐0029
1640‐0030
1640‐0031
1640‐0032
1640‐0033
1640‐0034
1640‐0035
1640‐0036
1640‐0038
Description
Step below cab door; stirrup style without back wall. Located [#LOC]. Steps under Front Cab doors shall not interfere with Approach Angle.
Step below cab door; smooth plate painted black durabak. Located [#LOC]. Steps under front cab doors shall not interfere with approach angle.
Diamond plate trim package for a (2) door Freightliner M2 106/112. Includes driver and officer step trim that will utilize pieces already supplied by the OEM.
Cab entrance steps, Navistar, open grating, Wildland
Under cab compartments, stainless steel hinged doors, painted job color, Wildland
Cab swing steps (LHS and RHS) shall be upgraded to permit additional step surface area IPOS swing steps.
Steps below front cab door ‐ CFR swing style (PR) painted black Durabak. Includes plunger stop to hold in the down position. Step to be centered below cab step.
Removable bottom panel on cab steps.
Diamond plate trim package for a (2) door Freightliner 114SD. Includes driver and officer step trim that will utilize pieces already supplied by the OEM.
Step below cab door Zico VS‐20‐5 elect swing out/down. Step to extend when door is opened and retract when closed. Steps shall be flush with outter edge of cab when stowed. Location: Each cab door
Each cab step well's kick plates and steps shall be aluminum smooth plate IPO diamond plate and all surfaces painted black durabak up to and below cab floor level.
Each cab step well's kick plates and steps shall be aluminum smooth plate IPO diamond plate and all surfaces painted Gray Zolatone up to and below cab floor level. All step surfaces provided with a multi‐directional, aggressive gripping surface (Gator Grip) incorporated into the aluminum smooth plate.
Each cab step well's kick plates and steps shall be aluminum smooth plate IPO diamond plate and all surfaces painted Black Scorpion (rough finish) up to and below cab floor level. All step surfaces provided with a multi‐directional, aggressive gripping surface (Gator Grip) incorporated into the aluminum smooth plate.
Step below cab door Zico VS‐20‐5 elect swing out/down. Step to extend when door is opened and retract when closed. Steps shall be flush with outter edge of cab when stowed. Location: Front cab doors.
Diamond plate trim package for a (2) door Freightliner 112/114SD. Includes driver and officer step trim that will utilize pieces already supplied by the OEM. For use with Hyd drive pump systems, includes extended lower steps and brackets supports for service and access to hydraulic reservoir.
Steps below rear cab door ‐ CFR swing style (PR) painted black Durabak. Includes plunger stop to hold in the down position. Step to be centered below cab step.
Each cab step well's kick plates and steps shall be aluminum diamond plate without a multi‐directional, aggressive gripping surface (Gator Grip). Includes embossed diamond plate bolt‐on panels at each lower step area.
LINE‐X package for custom cab steps: Includes cab step wells (everything below the cab floor) and all welded and bolt on steps including stirrup and swing out steps as applicable. Steps hanging below the cab shall have LINE‐X coating inside and outside. DEF tank door or any other access doors are also included in this package if located in the step well area below the cab floor.
Intermediate front cab door step (PR).
PRICE
$248.00
$326.00
$1,352.00
$2,658.00
$5,312.00
$435.00
$1,083.00
$234.00
$1,897.00
$1,650.00
$650.00
$650.00
$650.00
$1,650.00
$2,428.00
$1,083.00
$650.00
$981.00
$476.00
Option No.
Description
PRICE
1640‐0039
1640‐0040
Steps below rear cab door ‐ CFR swing style (PR). Includes plunger stop to hold in the down position. Step to be centered below cab step.
TBD
LINE‐X package for custom cab steps (NO DOORS): Includes cab step wells (everything below the cab floor) and all welded and bolt on steps including stirrup and swing out steps as applicable. Steps hanging below the cab shall have LINE‐X coating inside and outside. DEF tank door or any other access door located in the step well area below the cab floor SHALL NOT have LINE‐X finish.
Front steps below cab doors to be reduced approx. 3" in width. Steps to be offset forward in the stepping area.
Upgrade the cab bolt‐on steps to include cutouts with Grip Strut inserts, IPO Gator Grip.
Diamond plate trim package for a (2) door Peterbuilt 348‐367. Includes driver and officer step trim that will utilize pieces already supplied by the OEM.
Step below cab door. Open back style with angled corners. Located [#LOC]. Steps under front cab doors shall not interfere with approach angle.
Lower steps to extend 1.5" past cab. Barrier doors only.
Lower steps to extend 3.5" past cab. Barrier doors only.
Step below cab door to be hinged. Located [#LOC]. Steps under front cab doors shall not interfere with approach angle.
Ramco 6001FFR mirrors. Remote controlled with top CAS750 convex. Location: [#LOC].
Ramco 6001MCR mirrors. Remote controlled with bottom convex. Location: [#LOC].
Velvac 2010 mirrors. Door mounted west coast style with remote control and heat.
Mirrors (PR) heated with 4 way adjustment.
Mirror, 8" convex to be cab mounted [#LOC].
3" Extension for Ramco Mirrors
4.5" Extension for Ramco Mirrors.
Retrac West Coast mirrors mounted on cab doors.
Cab mirrors for tiller cab. Includes one inside at front center overhead and one each side exterior mounted.
Mirrors heated with 4 way adjustment, 24VDC.
Both cab mirrors to be heated.
Ramco 6001FFR mirrors. Remote controlled with top CAS750 convex.
Velvac 2010 mirrors with marker lights. Door mounted west coast style with remote control and heat.
Officer side Velvac #2010 mirror to be mounted on forward corner of cab in place of door location.
Mirror Stainless Steel 8" Convex above officer side cab brow, Bell Type Mounting, 2 Piece Adjustable Telescoping Arm. Head #983, Arm #3983
Velvac mirrors model 2025 with LED directional arrows. Door mounted (bottom mount) with remote control and heat.
Ramco 6001CCR‐750 mirrors. Remote controlled with bottom convex and top CAS750 convex. Location: [#LOC].
Ramco 6001FFR mirrors. Remote controlled with CAS750R top remote convex. Location: [#LOC]
Mirror Stainless Steel 8" Convex above driver side cab brow, Bell Type Mounting, 2 Piece Adjustable Telescoping Arm. Head #983, Arm #3983
Freightliner West Coast cab mirrors. Tradition.
$1,005.00
$981.00
1640‐0041
1640‐0042
1640‐0043
1640‐0044
1640‐0045
1640‐0046
1640‐0047
1640‐0049
1670‐0001
1670‐0002
1670‐0003
1670‐0004
1670‐0005
1670‐0007
1670‐0008
1670‐0010
1670‐0011
1670‐0012
1670‐0013
1670‐0014
1670‐0015
1670‐0016
1670‐0017
1670‐0018
1670‐0019
1670‐0021
1670‐0023
1670‐0024
$875.00
$0.00
$564.00
$1,352.00
$248.00
$0.00
$0.00
$248.00
$1,650.00
$1,310.00
$704.00
$844.00
$92.00
$171.00
$171.00
$324.00
$314.00
$844.00
$321.00
$1,633.00
$741.00
$440.00
$97.00
$1,209.00
$1,756.00
$1,906.00
$97.00
$0.00
Option No.
1670‐0025
1670‐0026
1670‐0027
1670‐0028
1670‐0029
1670‐0030
1670‐0031
1670‐0032
1670‐0034
1670‐0035
1670‐0036
1670‐0037
1670‐0038
1670‐0039
1670‐0040
1670‐0041
1670‐0042
1670‐0043
1670‐0044
1670‐0045
1670‐0046
1670‐0047
1670‐0048
1670‐0049
1670‐0050
1670‐0051
1670‐0052
1670‐0053
1670‐0054
1670‐0055
1670‐0056
Description
Freightliner West Coast heated cab mirrors with remote control. Tradition.
International West Coast Heated Mirrors.
International West Coast Mirrors Heated with clearance lghts.
Rosco AccuStyle 818 door mounted mirrors (bottom mount). Chrome w/LED turn signals, remote, heated and convex.
International West Coast heated mirrors with clearance lights and remote control.
Kenworth model MX148S wide angle mirror. Location: [#LOC].
2" extension for Ramco mirrors.
Ramco 6001FFR mirrors. Remote controlled with top CAS750 convex and LED turn signals. Location: [#LOC].
Freightliner West Coast heated cab mirrors with remote control. Tradition.
Ramco 6001FFR mirrors with INVUE camera. Remote controlled with top CAS750 convex. Location: [#LOC].
Ramco 6001MCR mirrors with INVUE camera. Remote controlled with bottom convex. Location: [#LOC]
Ramco 6000CCR mirrors. Remote controlled with top CAS750 convex. Location: [#LOC].
Lang Mekra mirrors w/LED marker lights and turn signals. Door mounted west coast style with convex, remote control and heat.
Moto mirrors model 340530. Door mounted with driver heat; officer remote control and heat.
Velvac #2010 mirrors. Door mounted with remote control and heat. Custom ES.
Freightliner West Coast cab mirrors with black finish.
Freightliner West Coast heated cab mirrors with remote control. Includes bright finish.
Freightliner West Coast heated cab mirrors with remote control. Includes bright finish.
Ramco 6001FFR mirrors with INVUE camera and LED turn signals. Heated/remote controlled flat glass with heated/remoted controlled top CAS750 convex. Location: [#LOC].
Mirror stainless steel 10.5" convex mounted on tubular SS adjustable bracket. Locate officer side frt cab corner. Lower mount of main support arm to be approx even with center of quads (approx 5" outboard of quads) with arm extending upward. Short diagonal support arms to attach to frt of cab just above cab contour. Ref photo of Ville De Quebec HP100.
Ramco 6001MCR mirrors. Remote controlled with bottom convex and LED turn signals. Location: [#LOC].
Mirrors (PR), Ramco 6000CCHR‐750 mirrors with PRO364‐6 vertical extension. Remote controlled with bottom convex and a seperate top CAS750 convex. Location:[#LOC]
Retrac Aerodynamic remote heated mirrors (PR) mounted on cab doors.
Pair of hood mounted Lang Mekra convex mirrors (heated with black finish). International chassis only.
Ramco 6002PCR mirrors. Remote controlled flat glass with remote controlled bottom convex. Location: [#LOC].
Velvac west coast door mounted mirrors NYPD. Includes heated 7x16 flat glass with (2) twist clamps, 8" round convex and preset/pivot upgrade kit.
Ramco 6000‐PCHR mirrors. The mirrors shall incorporate heated and remote for both flat and convex using (2) Ramco model ELE‐310 switches. Location: [#LOC].
Moto mirrors model 7‐2386. Door mounted with remote control and heat.
Velvac mirrors model 2030 chrome with LED directional arrows. Front corner mounted with remote control and heat.
Velvac convex mirrors (PR). Model Top Hat bolt‐on convex mirror. For use with model 2025 or 2030 mirrors only.
Retrac west coast remote heated mirrors (PR) mounted on cab doors.
PRICE
$232.00
$0.00
$55.00
$1,215.00
$150.00
$194.00
$171.00
$2,203.00
$0.00
$2,909.00
$2,909.00
$1,650.00
$1,425.00
$1,183.00
$0.00
$0.00
$286.00
$0.00
$2,829.00
$367.00
$1,626.00
$1,574.00
$1,283.00
$343.00
$1,811.00
$972.00
$1,909.00
$998.00
$1,438.00
$219.00
$1,365.00
Option No.
Description
PRICE
1670‐0057
1670‐0058
(Use Sales Code 1670‐0050)Ramco 6001 mirrors. Remote controlled flat glass with remote controlled bottom convex. Location: [#LOC].
Mirror stainless steel 5" convex (PR). Locate above main mirror for viewing top of vehicle. West coast style mirrors only.
Retrac Mirror stainless steel 10" 3‐arm convex above officer side cab brow, 3 piece adjustable telescoping arm. Head #604953, Arm assy#604671
Velvac K10 mirror (PR). Location: Front cab corners (To be located at mid‐point inspection).
Retrac west coast heated mirrors (PR) with convex lower mounted on cab doors. Includes green marker on officer and red marker on driver.
Retrac Aerodynamic dual vision chrome west coast style mirrors (PR) mounted on cab doors. Includes remote control and heat for std and convex mirrors and LED marker light.
Velvac mirrors model 2025 with LED directional arrows. Door mounted (bottom mount) with remote control and heat full bottom glass and heated top hat convex. No lower convex.
Retrac west coast remote heated mirrors with lights (PR) mounted on cab doors.
Retrac Mirror stainless steel 10" 3‐arm convex above driver side cab brow, 3 piece adjustable telescoping arm. Head #604953, Arm assy#604671
Ramco 6001FFR black mirrors. Remote controlled with black top CAS750 convex. Location: [#LOC].
Ramco model CRM‐1752‐3HRT‐853 mirrors. The mirrors shall incorporate heated and remote for both flat and convex using (3) Ramco model ELE‐310 switches. Location: [#LOC].
$1,517.00
$147.00
1670‐0059
1670‐0060
1670‐0061
1670‐0062
1670‐0063
1670‐0064
1670‐0065
1670‐0066
1670‐0067
1670‐0068
1670‐0069
1670‐0070
1670‐0071
1670‐0072
1670‐0073
1670‐0074
1670‐0075
1675‐0001
1675‐0005
1675‐0006
1675‐0007
1675‐0008
Lang Mekra mirrors w/LED marker lights and turn signals. Black door mounted west coast style with convex, remote control and heat.
Mirrors wired with Duetsch connectors to allow for replacement.
Velvac mirrors model 2030 chrome with full face lower, upper bolt‐on convex and LED marker lights. Front corner mounted with remote control lower and dual heat.
Lang Mekra mirrors (No marker/turn). Door mounted west coast style with convex, remote control and heat.
Ramco model CRM‐310‐1350CCHR mirrors. The mirrors shall incorporate heat and remote using Ramco model ELE‐310 switch. Location: [#LOC].
Driver side Velvac 2010 door mounted west coast mirror with remote and heat. Officer side Ramco 6001FFR front corner mounted remote controlled with top CAS750 convex and heat.
Velvac V‐Max mirrors black with lower convex and LED marker lights. Door mounted (bottom mount)driver, front cab corner officer with remote control and heat.
Velvac V‐Max mirrors black with lower convex and LED marker lights. Includes main glass remote with heat upper/lower and 2" risers. Location: front cab corner.
Stainless steel trim belt on front of cab. Location: [#LOC].
Cab roof vent with‐out fan (pair). Location: (1) each side centered above rear cab doors.
Vent w/fan roof mounted, pair.
Diesel fuel only label.
Step chassis off road type pair. Required on all medium duty 4x4 chassis for each cab door if first step distance exceds 24 inches.
$301.00
$661.00
$960.00
$1,674.00
$1,278.00
$1,365.00
$301.00
$1,917.00
$2,294.00
$1,425.00
$0.00
$1,863.00
$1,425.00
$2,294.00
$1,328.00
$1,293.00
$1,637.00
$508.00
$397.00
$889.00
$0.00
$462.00
Option No.
1675‐0011
1675‐0013
1675‐0014
1675‐0015
1675‐0016
1675‐0019
1675‐0020
1675‐0022
1675‐0023
1675‐0024
1675‐0025
1675‐0030
1675‐0032
1675‐0033
1675‐0034
1675‐0035
1675‐0036
1675‐0038
1675‐0039
1675‐0040
1675‐0041
1675‐0042
1675‐0043
1675‐0045
1675‐0046
1675‐0047
1675‐0048
1675‐0049
1675‐0050
1675‐0051
1675‐0052
1675‐0053
1675‐0054
1675‐0055
Description
Windshield Wipers shall be Heated 12 Volt
Mud flaps (PR), front, black with logo.
SCBA bottle storage, two driver side of cab behind rear door with cast doors.
Cab roof mounted diamond plate 3 sided light tower shield with 45 degree front slope.
Cab roof mounted painted job color 3 sided light tower shield with 45 degree front slope.
Lower Cab Trim Diamond Plate
Auto eject stainless steel scuff plate.
Pair of 18" handrails located just behind driver and officer front door one each side.
Pair of 18" handrails located just behind driver and officer rear door (ALS doors if equipped) one each side.
Pair of 36" handrails located just behind driver and officer rear door (ALS doors if equipped) one each side.
SCBA bottle storage, two officer side of cab behind rear door with cast doors.
Mud flaps, front, black with E‐ONE logo.
On top of cab roof for storage of one stokes basket and three backboards. Stokes basket is 84Lx24Wx7H. Backoard dim is 71Lx16Wx2H/ Box is to be 48Wx86Lx10H. Locate a divider 28" from driver side for stokes opening and a stop for back on cab with access from top mount walkway. Drop down door with thumb latches. Box is to be centered side to side.
Chrome fire bell with eagle. Location: Officer's side of front bumper extension.
Cab driprail drain holes. The driprail just before the vista roof begins to have a drain hole provided (one each side of cab).
Belt size tag. Install next to fluid capacity tag. Tag to provide belt sizes for all belts provided.
Cab wheel well liners. The cab wheel well liners to be aluminum IPO ABS plastic. Paint job color.
Sign plate smooth 30" x 30" mounted on cab roof (vista if equipped). Color: [#COL].
Pair of 48" handrails located just behind driver and officer rear door (ALS doors if equipped) one each side.
Body and cab mud flap heights. Bottom of flaps to be approx. 12" off ground.
Stainless steel trim belt low on sides of cab.
Rear cab wall to be smooth 3/16" aluminum plate. Cab wall to be finish painted to match the cab paint scheme.
Sliding rear window mounted above pump panel. Top mount enclosed cab.
Hansen white LED cab handrails upgrade (EA).
Rear cab wall to be smooth 3/16" aluminum plate. Cab wall to be finish painted to match the cab paint scheme.
Rear cab wall to be 3/16" aluminum diamond plate.
Rear cab wall to be smooth 3/16" aluminum plate with a diamond plate overlay.
Rear cab wall to be smooth 3/16" aluminum plate with a diamond plate overlay.
Aerial Window Wipers shall be Heated 12 Volt
Heated Aerial Cab Windows for Snozzle units
Relocate commerical chassis batteries, location [#LOC].
Stainless steel scuff plates full height on rear cab corners (PR)
Sign plate smooth 18"x28" mounted one each side cab roof (vista if equipped). Color: [#COL]
Radio box 18W x 12H x 10D. Location: Centered up high of vista area recessed on the rear exterior cab wall with door hinged to the bottom.
PRICE
$1,036.00
$170.00
$784.00
$1,008.00
$1,255.00
$564.00
$100.00
$395.00
$395.00
$429.00
$784.00
$166.00
$2,347.00
$1,473.00
$93.00
$112.00
$637.00
$254.00
$494.00
$0.00
$1,507.00
$371.00
$1,187.00
$208.00
$0.00
$0.00
$464.00
$0.00
$798.00
$1,681.00
$849.00
$256.00
$503.00
$534.00
Option No.
1675‐0056
1675‐0057
1675‐0058
1675‐0059
1675‐0060
1675‐0061
Description
Stainless steel scuff plates on rear cab roof corners (PR)
Mounting plate for battery charger receptacle and indicator ‐ removable brushed stainless steel.
Chrome fire bell with gold eagle. Location: Officer's side of front bumper extension.
Rear cab wall to be smooth 3/16" aluminum plate with swirl plate overlay.
Sign plate smooth 40" x 80" mounted on cab roof (vista if equipped). Color: [#COL]
Cab roof mounted 4 sided light tower shield painted job color.
PRICE
$194.00
$303.00
$1,552.00
$763.00
$729.00
$1,632.00
1675‐0062
1675‐0063
1675‐0064
1675‐0065
1675‐0066
1675‐0067
1675‐0068
1675‐0070
1675‐0071
1675‐0072
1675‐0073
1675‐0074
1675‐0075
1675‐0076
1675‐0077
1675‐0078
Electric chrome fire bell with eagle. Location: Driver's side of front bumper extension. Includes switch on officer side overhead console.
Mud flaps, front, black without logo.
(1) 36" handrail located just behind rear door (ALS doors if equipped). 3 door custom cabs only.
Stainless steel roller assemblies for back of cab. (1) each side rear cab corners.
Skid plate under each lower step. Quest cab only.
Cab roof mounted 3 sided light tower shield painted two‐tone job color.
Freightliner provided Exterior Composite Sun Visor
Body mud flap heights. Bottom of flaps to be approx. 12" off ground.
Remove side grille from wheel well areas of the cab. TyphoonX cab only.
(4) roof mounted (welded) sign plate mounting points. Mounts to space roof sign plate off cab roof and allow for easy removal.
Hose deflector pin to protect Q2B on front bumper extension.
Cab roof mounted 3 sided light tower shield with welded sides and painted job color with 45 degree front slope.
Cab roof mounted painted job color 3 sided light tower shield with 90 degree front slope.
Cab roof mounted diamond plate 3 sided light tower shield with 90 degree front slope.
Storage box on rear cab roof 48W x 48L x 12H with 4‐sided lid painted two‐tone job color (if applicable)
Hansen red LED cab handrails upgrade (EA).
Diamond plate storage box for Little Giant model 17 on rear cab vista roof. Includes drop down door with push button latches and nylatron on floor.
Fixed rear cab wall narrow windows (ea). Location: driver side rear wall.
Smooth plate sides painted job color and diamond plate top/door storage box for Little Giant model 17 on rear cab vista roof. Includes 45 degree front angle, rear backstop, partition, drop down door with push button latches and nylatron on floor.
Stainless steel scuff plates full height on Quest rear cab corners (PR).
Standard Non Heated Windshield
Side extensions at cab wheel wells for 4x4 application.
Under riser half depth roll‐out trays. Includes cab floor extensions. Requires riser height exterior compartments.
Raised cab wheel wells for low OAH applications.
Pair of handrails (8" driver and 18" officer) located just behind driver and officer front door.
Fluid capacity tag to include filter model numbers for engine oil, transmission, fuel, air, hydraulic and coolant. Tire size front and rear to be included on tag.
$2,060.00
$170.00
$218.00
$308.00
$458.00
$1,255.00
$202.00
$0.00
$251.00
$294.00
$221.00
$1,484.00
$1,255.00
$1,008.00
$2,049.00
$208.00
1675‐0079
1675‐0080
1675‐0081
1675‐0082
1675‐0083
1675‐0084
1675‐0085
1675‐0086
1675‐0087
1675‐0088
$1,499.00
$65.00
$3,441.00
$465.00
$1,148.00
$890.00
$1,332.00
$462.00
$509.00
$112.00
Option No.
1675‐0089
1675‐0090
1675‐0091
1675‐0092
1675‐0093
1675‐0094
1675‐0095
1675‐0096
1675‐0097
1675‐0098
1675‐0099
1675‐0100
1675‐0101
1675‐0102
1675‐0103
1675‐0104
1675‐0105
1675‐0106
1675‐0107
1675‐0108
1675‐0109
1675‐0110
1675‐0111
1675‐0112
1675‐0113
1675‐0114
Description
Radio box 18W x 12H x 10D. Location: Up high center rear wall panel offset to driver side of vista area recessed on the rear exterior cab wall with door hinged to the bottom. Includes rubber bumpers on upper corners of door.
Light tower riser ahead of vista. For use with large towers. Installed tower to not exceed over all height of vista roof.
Lightbar mounting angles (PR). Position on cab roof with each angle oriented front to rear with one leg welded to cab roof leaving top horizontal surface for lightbar mounting legs.
Number plate mounting. "Z" type extrusions welded to cab roof (upper leg facing out) to support perimeter of sign plate. Allows sign to be attached without drilling through cab roof.
Grille on side of cab over wheel (PR). Grilles are non‐venting and for cosmetic purposes only. Includes black‐out surface behind grilles.
Microphone/Speaker box. 11"H x 9"W x 6.5"D Location: Centered up high recessed on the rear vista exterior cab wall with vertically hinged door.
Diamond plate storage box on rear cab roof 80W x 36D x 14H with lid.
Fixed rear cab wall narrow windows (ea). Location: officer side rear wall.
Tag for Auto eject receptacle inlet 20amp outside drivers door shall have a tag that reads "CHASSIS BATTERIES".
Rear cab door handrail package. Includes exterior mounted 18" extruded aluminum handrail driver side located just behind rear door and interior mouned rubber covered grab handle officer side at rear of opening.
SCBA bottle storage (4) officer side of cab behind rear door with cast door. Upper storage compt will be spaced up above lower three due to rear wall support. N/A with exterior cab handrail (requires inside grab rail).
Fixed window on driver side of cab. Custom ES.
Fixed window on officer side of cab. Custom ES.
Rear cab wall windows fixed narrow (PR). Custom ES.
Cab wheel well liners (PR). Custom ES.
Cab wheel well liners (PR). Officer side liner notched for use with a 5" front intake. Custom ES.
The exterior rear of the cab to have a diamond plate overlay. For use with a top mount application.
The exterior rear of the cab to have a diamond plate overlay. For use with a top mount application.
The lower center area of the rear cab to have aluminum plate overlay.
The lower center area of the rear cab to have aluminum plate overlay. International.
Polished stainless steel scuff plates full height on Quest rear cab corners (PR).
Cab exterior hand rails to use Austin Hardware model GR‐002‐AL‐BRT‐144 knurled bright anodized aluminum tubes IPOS.
Pair of 24" handrails located just behind driver and officer front door one each side. Handrail to extend 6" lower than standard for 4x4 application.
Pair of 24" handrails located just behind driver and officer rear door (ALS doors if equipped) one each side. Exterior handrail to extend 6" lower than standard for 4x4 application. Includes interior rubber grab handles on rear facing wall of driver and officer side wheel well risers.
Pair of handrails (36" driver exterior and 18" officer interior) located just behind driver and indside officer rear door. ALS cab with multiple height exterior access only.
An electrical tether assembly provided on rear cab wall for use with in cab control console electronics.
PRICE
$534.00
$1,829.00
$298.00
$411.00
$260.00
$534.00
$1,813.00
$65.00
$287.00
$312.00
$1,566.00
$0.00
$0.00
$257.00
$0.00
$0.00
$0.00
$0.00
$0.00
$0.00
$465.00
$132.00
$414.00
$636.00
$429.00
$3,771.00
Option No.
1675‐0115
1675‐0116
1675‐0117
1675‐0118
1675‐0120
1675‐0121
1675‐0123
1675‐0124
1675‐0125
1675‐0126
1675‐0127
1675‐0128
1675‐0129
1675‐0130
1675‐0131
1675‐0132
1675‐0133
1675‐0134
1675‐0135
1675‐0136
1675‐0137
1675‐0138
1675‐0139
1675‐0140
1675‐0141
1675‐0142
Description
Rear cab handrails to be mounted centered between rear doors and rear wall.
Brushed stainless steel scuff plates for cab handrails (PR).
Rubber liners shall be added to the forward cab wheel wells.
Fluid capacity tag to include lug nut torque specs for front and rear wheels in addition to required information.
Unleaded fuel only label.
Exterior windshield visor. Includes DOT lighting. Visor painted primary upper cab color. Kenworth.
Chrome fire bell laser etching. Requires design provided in digital format. One side only.
Additional fluid capacity tag in French.
Mounting plate for battery charge receptacle, indicator and air auto eject receptacle ‐ removable brushed stainless steel.
Diamond plate storage box on rear cab roof 70W x 40D x 8.5H with lid.
Module for stokes basket/ backboard/ EDP restraint bar/ ballistic blanket and pneumatic strut storage enclosure module constructed of 12 gauge stainless steel shall be located behind chassis cab driver/ passenger area. Accessed via hinged drivers/ passenger side stainless steel lap doors with locking Bent D ring latch handles.
Exterior cab grab handles (PR) shall be made using knurled grip surface, bright anodized Austin Hardware handrail materials IPOS.
Cab roof mounted 3/16" diamond plate 4 sided light tower/ AC condensor shield with 90 degree front slope.
Mounting plate for battery charge receptacle, indicator, air auto eject receptacle and block heater receptacle ‐ removable brushed stainless steel.
Auto Kwikee step. Location: [#LOC].
Customer supplied fire bell for dealer installation. Includes: bracing under extended front bumper extension (as applicable), bulk head fiting and pull cable. Location: Officer's side of front bumper extension.
Rear cab and vista glass (if so equipped) to be dark tint (smoked glass with approx 50% light transmittance) IPOS. Includes all glass rearward of front cab doors.
Cab wheel well liners. The cab wheel well liners to be aluminum with sanded finish IPO ABS plastic.
Sign plate smooth with sanded finish 20" x 20" mounted on cab roof forward of vista.
Radio box 18W x 14H x 12D. Location: Up high center rear wall panel of vista area recessed on the rear exterior cab wall with door hinged to the bottom. Includes rubber bumpers on upper corners of door.
Tag for front grille, front of bumper and both side of hood shall have a tag that reads "REMOVE MONITOR BEFORE LIFTING". See photos on file.
Cab roof mounted 3 sided roof mounted AC shield with 45 degree front slope painted two‐tone job color.
Rubber fenderette in additon to standard fender.
Cab roof mounted diamond plate 3 sided AC shield with 45 degree front slope.
Radio box 32W x 7H x 6D. Location: Centered up high of vista area recessed on the rear exterior cab wall with door hinged to the top. Includes plunger hold open.
Radio box 12W x 8H x 6D. Location: Centered up high of vista area recessed on the rear exterior cab wall with door hinged to the top. Includes plunger hold open.
PRICE
$0.00
$218.00
$422.00
$112.00
$0.00
$135.00
$659.00
$112.00
$303.00
$1,813.00
$5,834.00
$744.00
$1,177.00
$303.00
$876.00
$455.00
$599.00
$520.00
$254.00
$534.00
$287.00
$1,029.00
$307.00
$783.00
$596.00
$534.00
Option No.
1675‐0143
1675‐0144
1675‐0145
1675‐0146
1675‐0147
1675‐0148
1675‐0149
1675‐0150
1675‐0151
1675‐0152
1675‐0153
1675‐0154
1675‐0155
1675‐0156
1675‐0157
1675‐0158
1675‐0159
1675‐0160
1675‐0161
1675‐0162
1675‐0163
1675‐0164
1675‐0165
Description
A diamond plate storage box shall be mounted on top of the cab roof for storage of (1) stokes basket model 71. Stokes basket is 86Lx24Wx8H. Box is to be 26Wx87.5Lx9H in front, box will be sloped to match Vista rise. Box will be opened from the rear. Restraints will be included in the box to secure the basket in place. Box is to be centered side to side.
Pair of 24" handrails located just behind driver and officer front door one each side.
Diamond plate cover to protect the air conditioner lines on the cab roof.
Polished stainless steel scuff plates full height on rear cab corners (PR).
Electric chrome fire bell with eagle. Location: Driver's side of front bumper extension. Includes switch on officer side dash.
Bottom of enclosed top mount overhang raised 3" for increased height pump module.
The battery charger receptacle mounting plate shall be fabricated using 3/16" aluminum smooth plate. It shall be painted to match cab two tone job colors and align with the paint break as mounted.
Storage box on back of cab above top mount walkway for backboard/stretcher. Backboard dim is 72Lx27Hx8D; stretcher dim is 65Lx17Hx4D. Box is to be diamond plate 76Lx27Wx8H with a vertically hinged door at each side with a thumb latch in each door. Box to be centered side to side approximately 4" above top mount walkway.
Pair of 24" handrails located in the interior of driver and officer rear doors. The handrails shall be mounted on the rear wall. If equipped with an ALS cabinet the handrails shall be mounted on the ALS interior surface, outboard of the ALS access door within easy reach of rear door entry personnel.
Sign plate smooth 40" x 40" mounted on cab roof (vista if equipped). Color: [#COL].
SCBA bottle storage two driver and officer side of cab behind rear door with 3/16" plate doors painted job color.
The cab shall have trim plates made from diamond plate to overlay the existing commercial cab closeout panels below the doors left and right.
Painted visor for International 4400 cab. Option 16XWD.
Polished stainless steel scuff plates full height on Quest rear cab corners (PR) to provide protection of painted surface(s) from quartz lighting as well as hose and or equipment as it is being removed from apparatus.
The exterior lower rear of the commercial cab to have a diamond plate overlay. For use with a top mount application.
Backboard storage sleve for (1) board. Includes retaining strap for board. Loc: [#LOC].
Mounting plate for battery charge receptacle, indicator and block heater receptacle ‐ removable brushed stainless steel.
Backboard storage compartment for (1) board. Includes (2) hinged doors (1) each side with (2) push button latches for each door. Loc: [#LOC].
Escape hatch located on rear cab roof.
Cab roof vent with‐out fan (pair). Location: (1) each side offset above driver and officer.
Storage box (additional) to house light tower controls/tether, mounted on the rear of the cab roof offset to the driver side (exterior). The storage box shall be constructed of tread plate, include a drop down door tied into the door ajar circuit and thumb latch(s).
Cab roof mounted painted job color 3 sided light tower shield with 45 degree front slope to match the height of the light tower in the bedded position (+1" ‐0").
The fluid capacity label shall be English and feature all metric units of measure and shall be permanently affixed on the vehicle near the driver seating area IPOS.
PRICE
$1,572.00
$414.00
$236.00
$465.00
$2,060.00
$0.00
$149.00
$1,499.00
$411.00
$337.00
$1,566.00
$415.00
$210.00
$465.00
$176.00
$736.00
$303.00
$897.00
$1,324.00
$397.00
$384.00
$1,368.00
$0.00
Option No.
1675‐0166
1675‐0167
1675‐0168
1675‐0169
1675‐0170
1675‐0171
1675‐0172
1675‐0173
1675‐0174
1675‐0175
1675‐0176
1675‐0178
1675‐0179
1675‐0180
1675‐0181
1675‐0182
1675‐0183
1675‐0184
1675‐0185
1675‐0186
1675‐0187
Description
Cab roof mounted painted job color 3 sided light tower shield with 45 degree front slope. Located rearward on flat roof (non vista). Placement to allow 45 degree shield to be placed in normal vista rise location to allow cab to appear to have vista roof.
Sign plate mounted to the full width front bumper center hose tray lid. Smooth plate painted FLNA4145 Black sized according to space available.
Sign plate smooth 30" x 45" mounted on cab roof (vista if equipped). Color: [#COL].
Door single vertically hinged painted with Tri‐Mark latch. Location(s): driver side canopy area of cab.
Embossed diamond plate in place of ALL standard and optioned diamond plate on cab.
Cab roof mounted 3 sided dual air condensor shield with 45 degree front slope. The shield shall be constructed using smooth aluminum plate. Finish: Painted to match upper cab.
Aerodynamic, painted roof color for International 4400 cab; Includes integral clearance/marker lights.Option 0016XWD (Tradition ES).
Radio box 32"W x 7"H x 6"D. Location: Centered up high of vista area recessed on the rear exterior cab wall with door hinged to the bottom. Door to fold down as far as possible to cab.
Hansen green LED cab handrails upgrade (EA).
Window, a fixed window w/approx dim 12 in tall x 26 in wide, provided on the driver`s side of cab in place of rear door location and above counter. The top edge of the window shall be inline with the top edge of the front door window.
Sign plate smooth with sanded finish 5" x 30" mounted forward facing on the light tower enclosure.
Awning rear of cab rearward facing. A wind deflector shall be mounted rearward on the cab roof full width as part of the pump module awning. On the back side of the wind deflector a vertical mounting plate shall be included. An awning mounting bracket shall be mounted to the wind deflector vertical plate. The awning mounting bracket shall include 6" of vertical adjustment to allow the awning to be manually raised up to 6" higher from its base position and include plate work to shield light when raised to the desired height. A 12V Marquee Over the Door/Window awning 72" long X 36" extension white in color shall be mounted in place on the adjustable bracket centered about the top mount pump panel. An awning deployment switch shall be included on the pump instrument panel. The awning deployment and adjustable height shall be included in the door ajar circuit.
Module for stokes basket/ backboard/ EDP restraint bar/ ballistic blanket and pneumatic strut storage enclosure module constructed of .187 aluminum plate and shall be located behind chassis crew cab area. Accessed via hinged drivers/ passenger side aluminum plate lap doors with locking Bent D ring latch handles and Medco locks.
ALS cab doors constructed of aluminum to match stainless steel body door design and latching. Includes d‐ring with Medco key.
(1) 48" handrail located just behind rear door (ALS doors if equipped). 3 door custom cabs only.
Mounting plate for battery charger receptacle and indicator ‐ removable polished stainless steel.
Side fixed windows behind rear doors. Windows to be same height as canopy windows. 80" cab with medium doors only.
Chrome fire bell with eagle. Location: Officer's side front cab corner.
Two (2) pair of 30" handrails. One (1) pair located just behind driver and officer rear door (ALS doors if equipped) one each side for access of cab rear door each side. The other pair located behind rear doors and rearward of handrails one each side for access to top mount walkway each side.
Sign plate smooth 30" x 30" mounted on cab roof forward of vista. Color: [#COL].
Pair of 24" handrails located just behind driver and officer rear door one each side.
PRICE
$1,364.00
$188.00
$337.00
$981.00
$1,539.00
$1,008.00
$167.00
$596.00
$208.00
$170.00
$166.00
$4,021.00
$6,155.00
$0.00
$249.00
$303.00
$338.00
$1,584.00
$813.00
$254.00
$414.00
Option No.
Description
1675‐0195
1675‐0196
1675‐0197
1675‐0198
1675‐0199
1675‐0200
1675‐0201
1675‐0202
Transverse compartment insert to accommodate driver side: (1) Zico universal air pack bracket, (1) FRC 120V Spectra tripod light, (2) long back boards; officer side: (1) Model 17 Little Giant ladder, (2) 6' NY Multi‐pupose hooks, (1) FRC 120V Spectra tripod light and (2) long backboards. (1) Model 71 stokes basket transverse mounted. The compartment is constructed with .187 aluminum plate.
Door single vertically hinged painted with Tri‐Mark latch. Location(s): officer side canopy area of cab.
Hard Suction Storage Rack (PR). Driver/officer side cab roof. Includes spring hold downs and scuff plates behind spring mounts (as applicable). Racks installed front to rear between side light bars and light tower.
Sign plate smooth with painted finish 24" x 24" mounted on cab roof forward of vista. Color: [#COL].
Rear cab wall to be smooth 3/16" aluminum plate painted black Durabak. Includes rear facing extrusions.
Polished stainless steel trim belt low on sides of cab. No black trim on upper and lower areas.
Windshield washer bottle guard.
Body compartment interior painted black Durabak. Only for half height compartments. IIncludes Back, Top, Bottom (unless it is diamond plate) and Side Walls Compartment: [#LOC].
Access door for DEF tank mounted under cab. Cast aluminum with brush finish. For use with 2 or 3 door E‐ONE cabs only.
Window cab side fixed officer's above medical cabinet.
Polished stainless steel trim belt low on sides of cab.
Strap, loop style to retain SCBA bottle (EA). Locate one in each cab SCBA compartment.
Hansen blue LED cab handrails upgrade (EA).
Large radius cab wheel well. Includes bolt‐on adjustable wheel well trim.
Mounting plate for battery charger receptacle, indicator, air inlet, etc (if applicable). Plate to be removable brushed stainless steel.
1675‐0203
Radio box 12W x 8H x 6D. Location: Centered up high of vista area recessed on the rear exterior cab wall with door hinged to the bottom.
1675‐0204
1675‐0205
1675‐0206
1675‐0207
1675‐0208
The cab roof shall be diamond plate painted black durabak. If equipped with trough overlay plate, it shall be painted black durabak also.
Drip pan for a ROM roll‐up door (EA). Location(s): driver and officer side ALS door.
Pair of 18" handrails located on ALS doors just behind driver and officer rear door.
Mount dealer supplied Black‐Rak weapons mount(s) in cab enclosure. Includes 12VDC wiring connections.
Cab exterior hand rails to be Stainless steel knurled grip surface hand rails in place of standard anodized handrails.
Stainless steel full height wrap on rear cab corners (PR). Includes under handrails behind rear cab doors (if equipped). Not available on long or extended cab with medium doors.
Cab roof mounted 3 sided roof mounted AC shield with 45 degree front slope painted job color.
Rear cab wall ventilation with custom cover. 2Dr NYPD cabs only.
Mounting plate for battery charger receptacle, indicator and air inlet (if applicable). Plate to be removable polished stainless steel.
Mounting plate for battery charger receptacle, indicator and air inlet (if applicable). Plate to be removable stainless steel painted job color.
Rubber fenderettes in place of standard fender.
Brushed stainless steel 4" wide scuff plates for cab handrails (PR).
1675‐0188
1675‐0189
1675‐0190
1675‐0191
1675‐0192
1675‐0193
1675‐0194
1675‐0209
1675‐0210
1675‐0211
1675‐0212
1675‐0213
1675‐0214
1675‐0215
PRICE
$6,155.00
$981.00
$806.00
$254.00
$763.00
$1,781.00
$126.00
$375.00
$127.00
$170.00
$1,781.00
$0.00
$208.00
$0.00
$0.00
$534.00
$965.00
$178.00
$395.00
$6,290.00
$325.00
$472.00
$1,029.00
$170.00
$0.00
$161.00
$307.00
$218.00
Option No.
1675‐0216
1675‐0217
1675‐0218
1675‐0219
1675‐0220
1675‐0221
1675‐0222
1675‐0223
1675‐0224
1675‐0225
1675‐0226
1675‐0227
1675‐0228
1675‐0229
1675‐0230
1675‐0231
1675‐0232
1675‐0233
1675‐0234
1675‐0235
1675‐0236
1675‐0237
1675‐0238
1675‐0239
1675‐0240
1675‐0241
1675‐0242
1675‐0243
Description
Pair of 48" handrails located just behind driver and officer door one each side.
LINE‐X package for custom cab roof: All roof plate surfaces including the rear lip over the back wall and trough plates if applicable shall have LINE‐X coating. All plate work (risers, boxes, etc) fabricated at E‐ONE and installed on the roof shall be included in this package.
LINE‐X package for custom cab back wall (exterior only): The entire exterior back wall (platework and extrusions) shall have LINE‐X coating.
LINE‐X package for custom cab fenderettes.
Chrome fire bell. Location: Officer's side of front bumper extension.
Window cab side fixed driver's above medical cabinet.
Fluid capacity tag to include filter model numbers for engine oil, transmission, fuel, air, hydraulic and coolant. Tire front/rear size and pressure to be included on tag. Include engine belt number(s) and egine serial number on plate.
SCBA bottle storage, one officer side of cab behind rear door above suction piping with cast door.
Mount dealer supplied Black‐Rak weapons mount(s) in cab enclosure. Includes 12VDC wiring connections. NYPD only.
Lower barrier cab door steps to extend approximately 3.5" from side of cab.
Integral 110V heated glass for rear vista windows. Includes switch on pump panel.
Integral 110V heated glass for rear vista windows. Includes switch on rear overhead. TME cab with rear wipers only.
The aerial roof trough to have a 1/8" embossed aluminum diamond plate overlay.
Pair of one piece knurled stainless steel 18" handrails located just behind driver and officer front door one each side.
Pair of one piece knurled stainless steel 36" handrails located just behind driver and officer rear door (ALS doors if equipped) one each side.
Pike pole mount (PR). Locate (1) each side rearward of rear cab doors. Includes lower tube painted job color, upper PAC 1004 bracket and stainless steel scuff plate at top.
Customer supplied electric fire bell for dealer installation. Includes: bracing under extended front bumper extension (as applicable) and switch in officer side overhead panel. Location: Officer's side of front bumper extension.
Officer wheel well liner w/o notch for front intake.
Hansen amber LED cab handrails upgrade (EA).
Akron mounting fixture model# 14950007 for Akron 1495 Ladder Pipe monitor. Locate top of cab roof on driver side.
Recess mount for officer side exterior front cab handrail. Mount to match exterior paint.
Window cab side fixed (EA). Locate officer canopy area below side facing flood light.
"DEF Tank Inside Cab Door" label to be mounted on the exterior of the driver side rear cab door.
Sign plate smooth 36" x 48" mounted on cab roof (vista if equipped). Color: [#COL].
Custom cab roof trough overlay shall have LINE‐X coating.
Hansen rubber insert handrail material on exterior of cab ipos.
Number plate mounting. "Z" type extrusions welded to body roof (upper leg facing out) to support perimeter of sign plate. Provides formounting without drilling through roof.
Diamond plate trim approx. 2" tall below lower driver and officer side SCBA bottle doors on cab.
PRICE
$494.00
$1,791.00
$1,398.00
$151.00
$1,473.00
$170.00
$112.00
$393.00
$165.00
$0.00
$3,325.00
$3,325.00
$531.00
$533.00
$626.00
$718.00
$455.00
$0.00
$208.00
$627.00
$334.00
$170.00
$43.00
$337.00
$332.00
$80.00
$411.00
$160.00
PRICE
1675‐0244
1675‐0245
Description
Transverse compartment insert to accommodate: (1) one Stokes Basket Model CMC Rescue S/S dimensions 83"L X 23"W X 7‐1/4"H. (2) two backboards with dimensions 16"W X 2"T X 72"L, and long strut storage. (1) one 17' Little Giant Model 17 at the rear of the compartment with dimensions 25"W X 57"L X 8‐1/4"T. The forward compartment area shall be for additional storage. The compartment is constructed with .187 aluminum plate and include straps to secure equipment.
Polished stainless steel trim belt on front of cab. Location: [#LOC].
1675‐0246
Electric chrome fire bell with eagle. Location: Officer's side of front bumper extension. Includes switch on officer side overhead console.
$2,060.00
Option No.
1675‐0254
Pair of 24" handrails located just behind driver and officer rear door (ALS doors if equipped) one each side. Exterior handrail to extend 6" lower than standard for 4x4 application. Includes interior rubber grab handles on the door jamb of driver and officer side rear door.
Access door for DEF tank mounted under cab. Fire Shopp painted job color. For use with 2 or 3 door E‐ONE cabs only. Includes exended filler neck hose.
Pair of 24" handrails located just behind driver and officer front door one each side. Exterior handrail to extend 6" lower than standard for 4x4 application. Includes interior rubber grab handles low on interior forward door jamb.
Pair of one piece knurled stainless steel 48" handrails located just behind driver and officer rear door (ALS doors if equipped) one each side.
Akron mounting fixture model# 14950007 for Akron 1495 Ladder Pipe monitor. Locate top of cab roof on officer side.
Customer supplied electric fire bell for dealer installation. Includes: bracing under extended front bumper extension (as applicable) and switch in officer side overhead panel. Location: Driver's side of front bumper extension.
Hansen white LED knurled cab handrails upgrade (EA).
Rear cab and vista glass (if so equipped) to be dark tint (smoked glass with approx 30% light transmittance) IPOS. Includes all glass rearward of front cab doors.
1675‐0255
Pair of 48" handrails located just behind driver and officer rear door (ALS doors if equipped) one each side. Exterior handrail to extend 6" lower than standard for 4x4 application. Includes interior rubber grab handles on the door jamb of driver and officer side rear door.
1675‐0247
1675‐0248
1675‐0249
1675‐0250
1675‐0251
1675‐0252
1675‐0253
1675‐0256
1675‐0257
1675‐0258
1675‐0259
1675‐0260
1675‐0261
1675‐0262
1680‐0000
Mounting plate for battery charger receptacle, indicator and air inlet (if applicable). Plate to be removable stainless steel painted black.
LINE‐X rear cab corner scuff plates.
Diamond plate rear upper cab scuff plates for telepole light heads.
LINE‐X rear cab telepole light head scuff plates.
Swirled aluminum 7" wide scuff plates for cab handrails (PR). Includes adjusting handrails reward to accomodate scuff plate. Not available on medium cab or battery charge receptacle to rear of front cab door.
Stainless steel trim belt on front of cab to prevent the front face of the cab from accidental scratches from options stored inside or on top of the bumper. Located below the quad bezels.
Mounting plate for battery charger receptacle, indicator and air inlet (as applicable). Plate to be removable brushed stainless steel. Plate sized to best accommodate options at officer door location.
Air intake emergency shut‐down. Dash mounted guarded switch.
$6,155.00
$758.00
$636.00
$260.00
$636.00
$719.00
$627.00
$455.00
$281.00
$599.00
$716.00
$161.00
$350.00
$160.00
$350.00
$318.00
$508.00
$0.00
$1,722.00
Option No.
1680‐0001
1680‐0002
1680‐0005
1680‐0006
1680‐0007
1680‐0008
1680‐0009
1680‐0010
1680‐0011
1680‐0012
1680‐0013
1680‐0014
1680‐0015
1680‐0016
1680‐0017
1680‐0020
1680‐0021
1680‐0022
1680‐0028
1680‐0033
1680‐0034
1680‐0039
1680‐0040
1680‐0041
1680‐0042
1680‐0045
1680‐0046
1680‐0047
1680‐0050
1680‐0051
1680‐0053
1680‐0054
1680‐0055
Description
Block heater 1000 watt.
Block heater 1500 watt. Available on ISM, ISX and S60 only.
Thermatic fan clutch.
Drivelines 1710.
Drivelines 1810. Required on 1550 lb/ft torque or greater engines.
Tow eyes front painted below bumper/cab (PR).
Tow eyes front stainless steel below bumper / cab (PR).
Tow eyes front stainless steel mounted in up position. Requires 16" minimum bumper extension on custom chassis and 18" minimum bumper extension on commercial chassis.
Tow eyes rear below body, painted.
Tow eyes rear frame painted black.
Tow hooks front stainless steel in down position. Requires extended bumper on commercial chassis. If Non‐Extended bumper on Comm. Chassis, tow hooks are to be ordered with chassis.
Tow hooks front stainless steel mounted up. Requires 12" minimum bumper extension on custom and commercial chassis.
Trailer hitch Class III mounted rear.
Exhaust end chrome plated. Due to high heat from current emission exhaust systems, dis‐coloring of exhaust end may occur after prolonged use.
Hotshift PTO.
Exhaust end for Nederman. For exhaust extraction system.
Exhaust end for Plymovent. For exhaust extraction system.
Auto lube system Vogel. Chassis points only.
Block heater 120v 1500 watt with thermostat.
Rear Tow Shackles (Pair)
Hotshift PTO heavy dutyfor Bronto only
Thermatic fan clutch.
Extended Life Coolant
Dual Stage Air Cleaner
Tow hooks front painted in the down position.
Windows for improved visibility of jump seat area of cab. One (1) window each side of cab, rear of entrance door.
Central Chassis Lube 1 Point
Remote engine oil drain.
External Drain Tube Eng S60
Aerial hydraulic activation system.
Storage below rear bench seat. (1) hinged door on each side of the bench seat.
Cab floor modification ‐ box type. Located in center rear floor behind engine cover. Top of box to be covered with floor matting.
Cab Floor Mod ‐ Extnd Box Type. Required on RLP and HP100 Platform with stand alone hyd generator and all other CII/Quest applications with hyd gen pump direct mounted to top mtd pto.
PRICE
$543.00
$555.00
$1,506.00
$1,121.00
$1,756.00
$283.00
$710.00
$710.00
$651.00
$579.00
$849.00
$849.00
$1,036.00
$278.00
$2,089.00
$0.00
$288.00
$4,463.00
$549.00
$286.00
$5,834.00
$7,504.00
$505.00
$2,010.00
$293.00
$652.00
$2,943.00
$181.00
$184.00
$1,350.00
$648.00
$0.00
$0.00
Option No.
1680‐0066
1680‐0076
1680‐0078
1680‐0080
1680‐0081
1680‐0082
1680‐0084
1680‐0085
1680‐0087
1680‐0088
1680‐0090
1680‐0091
1680‐0092
1680‐0093
1680‐0094
1680‐0095
1680‐0096
1680‐0097
1680‐0099
1680‐0100
1680‐0103
1680‐0116
1680‐0117
1680‐0120
1680‐0121
1680‐0122
1680‐0124
1680‐0126
1680‐0127
Description
Vogel auto lube system for chassis points (up to 26) and jack system points (12).
Under front bumper 9K winch receiver. Includes electrical connection for portable winch application. Custom chassis only.
Tow hooks front OEM. Not available with extended E‐ONE installed front bumper. Tow hooks are OEM supplied with chassis.
Tow eyes front painted in up and down position. Tow eyes to use same holes for both sets.
Special cover kit for Memphis to include auto lube Vogel driver's side front frame and cannon plug cover
The air intake emergency cable reset. Officer side of cab below the front bumper. Locate so cable is not visible or can be pulled without reaching under the bumper.
Exhaust extension and reinforcement for Nederman exhaust extraction system.
Right hand steer commercial chassis. All body and pump module components to be located the same as a left hand steer chassis.
Radiator brush guard below cab.
Angle of approach to be 15 degrees. Angle of departure to be 15 degrees.
Block heater to have thermostatic controller.
Tow eyes front stainless in up position and painted in down position.
Tow blocks under front bumper extension.
Tow eyes front stainless steel with 3" holes mounted in up position. Requires 16 inminimum bumper extension on custom chassis and 18 in minimum bumper extension on commercial chassis.
Trailer hitch Class IV mounted rear.
Side underbody 9K winch receivers. Includes (2) side facing‐ (1) each below rearward body compartments for portable winch with electrical connection for winch.
Side underbody 9K winch receivers. Includes (2) side facing‐ (1) each below body compartment ahead of the rear wheels for portable winch with electrical connection for winch.
Angle of approach to be no less than 13 degrees. Angle of departure to be no less than 13 degrees.
Block heater 1500 watt wired through inlet receptacle. Available on ISM, ISX and S60 only.
Tinted windows for improved visibility of jump seat area of cab.
One (1) air horn mounted on the driver side hood with driver and officer mounted foot switches. International.
Oil pan heater. Fleetguard 22MM 150W/120V wired to shoreline.
Special cab tilt reservoir location. Reservoir to be located in the [#LOC].
Under the body there shall be equipped with a pair of receiver assemblies, each with a removable swivel hoist ring. One each side of apparatus. The receivers shall be square steel tubing, same size as a receiver for a Class III trailer hitch. Located behind the rear axle.
Under the body there shall be equipped with a pair of 12,000 lb receiver assemblies, each with a removable swivel hoist ring, or can be used with a Class III trailer hitch. One each side of apparatus. The receivers shall be locate in front of rear axle. Final location will depend on Engineering and driveline. 12v not included.
Tow eyes rear below body painted. Eyes to be on edge pointing to rear.
Boom support modification ‐ Tiller. Support to accommodate a 50" wide ladder tunnel.
Block heater 1000 watt wired through inlet receptacle (or block heater auto eject inlet receptacle if so equipped).
Block heater thermostat.
PRICE
$6,025.00
$1,965.00
$0.00
$563.00
$450.00
$228.00
$393.00
$0.00
$633.00
$0.00
$198.00
$988.00
$341.00
$957.00
$1,891.00
$1,661.00
$1,661.00
$0.00
$555.00
$1,115.00
$583.00
$515.00
$652.00
$3,635.00
$3,635.00
$651.00
$489.00
$543.00
$282.00
Option No.
1680‐0128
1680‐0129
1680‐0130
1680‐0131
1680‐0136
1680‐0137
1680‐0138
1680‐0139
1680‐0140
Description
The commercial chassis to have seat belt and chassis pre‐wiring for NFPA seating indicator and vehicle data recorder.
The commercial chassis to have seat belt and chassis pre‐wiring for NFPA seating indicator and vehicle data recorder.
High flow power steering pump. Includes additional cooler. Requires engineering evaluation. Not available in hot climates.
Tow eyes rear frame stainless steel.
Relocate the air governor to the steering reservoir bracket above the driver side frame rail.
Diesel Exhaust Fluid (DEF) 10 gallon tank. Location: [#LOC].
Cab step area trim plates provided on the driver and officer side.
Cab step area trim plates provided on the driver and officer side.
Cab step area trim plates provided on the driver and officer side.
PRICE
$243.00
$497.00
$546.00
$1,365.00
$201.00
$1,661.00
$203.00
$203.00
$203.00
1680‐0141
1680‐0143
1680‐0144
1680‐0145
Trim plate driver and officer step well area. Includes officer side mounting for battery charger receptacle and air inlet with auto eject.
The commercial chassis to have seat belt and chassis pre‐wiring for NFPA seating indicator and vehicle data recorder.
Trailer hitch class V mounted rear. This hitch has under body support as needed.
Diesel Exhaust Fluid (DEF) 5 gallon tank. Location: [#LOC].
$0.00
$0.00
$2,672.00
$1,576.00
1680‐0153
1680‐0154
1680‐0159
1680‐0164
1680‐0168
1680‐0169
1680‐0173
1680‐0174
1680‐0181
1680‐0182
1680‐0184
1680‐0185
Boom support modification ‐ 50' Boom. Support uprights to be offset 2" forward (MM application) from center of lower mounting holes.
Oil pan heater ‐ Fleetguard 150W/120V wired to block heater receptacle. ISC/ISL only.
Vogel auto lube system for chassis points (up to 26) and Bronto inboard jack extension cylinder points (4).
Diesel Exhaust Fluid (DEF) 5 gallon tank. Location: R1 floor offset forward. 2010 EPA Custom ES.
The commercial chassis to have seat belt and chassis pre‐wiring for NFPA seating indicator and vehicle data recorder.
The commercial chassis to have seat belt and chassis pre‐wiring for NFPA seating indicator and vehicle data recorder.
Engine block heater. Locate receptacle below the driver side cab door. International
Philips 1000 watt engine block heater. Locate receptacle below the driver side cab door. Freightliner.
Oil pan heater ‐ Fleetguard 300W/120V wired to block heater receptacle. ISM only.
Oil catch muffler to be located officer side rearward of frame mounted step.
Existing chassis to be modified to match wheelbase and frame cut of order configuration.
RUDD (Rotogrip) 18 strand automatic tire chains. Includes switch in cab.
$0.00
$450.00
$4,985.00
$0.00
$0.00
$0.00
$175.00
$127.00
$570.00
$0.00
$1,100.00
$3,281.00
1680‐0186
1680‐0187
1680‐0188
1680‐0189
Under the body to be equipped with a pair of receiver assemblies, each with a removable swivel hoist ring. One each side of apparatus. The receivers shall be square steel tubing, same size as a receiver for a Class III trailer hitch. Located to rear of front outriggers.
On‐Spot tire chain installation. Requires pre‐wire option located in Cab Electrical. Requires engineering review and approval if less than 176" WB.
Aerial hydraulics installed on bottom port of EVS4000/4500 transmission (to allow for flat rear cab floor). Requires drive through hyd pump option (6150‐0015) on aerials with hyd generator.
Tow eyes front painted mounted in up position. Requires 16" minimum bumper extension on custom chassis and 18" minimum bumper extension on commercial chassis.
$3,635.00
$2,975.00
$1,733.00
$283.00
Option No.
1680‐0192
1680‐0193
1680‐0194
1680‐0195
1680‐0196
1680‐0201
1680‐0202
1680‐0205
1680‐0208
1680‐0209
1680‐0210
1680‐0211
1680‐0212
1680‐0214
1680‐0217
1680‐0218
1680‐0222
1680‐0223
1680‐0224
1680‐0225
1680‐0226
1680‐0227
1680‐0228
1680‐0229
1680‐0231
1680‐0232
1680‐0234
1680‐0235
1680‐0239
1680‐0243
1680‐0245
Description
Forward facing under front bumper winch receiver. Includes lowered height for center bumper mounted tray depth and electrical connection for portable winch application. Commercial chassis only.
Tow eyes rear below body stainless steel.
Tow eyes front stainless steel through bumper / cab (PR).
Diesel Exhaust Fluid (DEF) 5 gallon tank. Location: Driver side below rear of cab. 2010 EPA Custom ES.
Tow eyes front painted through bumper / cab (PR).
Angle of approach to be no less than 12 degrees. Angle of departure to be no less than 13 degrees.
Trailer hitch Class III mounted rear. Rear hitch will be constructed from the class IV due to weight in B1.
Cab windows and locks to be power operated. Two (2) door International.
Storm King Air And Fuel Line Wraps, Wildland
Stainless steel air intake screens, HVAC and vents, Wildland
Tow hooks, below front frame, painted, Wildland
Rear tow eyes, painted steel, 3" diameter 3/4" plate, Wildland
Tow eyes mid‐ship painted in down position pair
Helmet holder locations: See photos on file with sales.
Driveline guard (EA).
Rear skid plates (PR). Locate below rear of body aft of rear outriggers.
Angle of approach to be no less than 10 degrees. Angle of departure to be no less than 10 degrees.
Under the body shall be equipped with a pair of 12K receiver assemblies. Location: (1) each side below rear compartments.
Air control panel for a chassis air outlet in compartment L2. The panel shall have quarter turn shut off valve, 0‐300 pounds per square inch air pressure gauge and a check valve in the supply line.
Two (2) heavy‐duty tow eyes plates made of 3/4" (0.75") thick steel having 3" diameter holes shall be bolted directly to the rear of the frame to allow towing. The tow plates shall be protruding out the rear of the body and shall be painted chassis black.
Shared aerial and hyd gen PTO system (for use with NPNT CR100/137/95‐Platform with SmartPower or Harrison gen)(Requires eng approval with water pump).
Tow eyes front painted with 3" holes below bumper/cab (PR).
Under front bumper Class III hitch receiver. Custom chassis only.
Step bars will be located under the entry doors of the cab each side. Bars will have a black powder coat finish.
Insta‐chain tire chain installation. Requires pre‐wire option located in Cab Electrical.
Painted lifting points (high visibility orange) for IFS front axle. Includes metal placard on driver side door of Timmoney diagram showing points.
The fuel tank to be [#COL] gallons and located to the [#LOC] of cab.
The batteries to be located under [#LOC] of cab.
Tow eyes rear frame painted mounted low just above tailboard.
Tow eye straight line pull tag located center front bumper extension.
Upgrade receiver and tow eye extension. The front bumper 9K winch receiver shall be extended forward, approximately 1" beyond front bumper IPOS (rather than at the under bumper location). Custom chassis only.
PRICE
$1,959.00
$2,152.00
$983.00
$0.00
$552.00
$0.00
$1,916.00
$582.00
$3,133.00
$429.00
$753.00
$1,118.00
$283.00
$0.00
$324.00
$3,128.00
$0.00
$3,635.00
$865.00
$836.00
$4,384.00
$710.00
$1,591.00
$852.00
$2,975.00
$366.00
$0.00
$0.00
$579.00
$0.00
$788.00
Option No.
1680‐0246
1680‐0247
1680‐0248
1680‐0249
1680‐0250
1680‐0251
1680‐0254
1680‐0255
1680‐0256
1680‐0258
1680‐0262
1680‐0263
1680‐0264
1680‐0265
1680‐0269
1680‐0270
1680‐0271
1680‐0272
1680‐0273
1680‐0274
1680‐0277
1680‐0279
1680‐0282
1680‐0284
1680‐0285
1680‐0286
1680‐0287
1680‐0288
1680‐0289
1680‐0290
Description
The cab tilt manual back‐up pump handle and mounting clips shall be shipped loose. Dealer to mount after delivery.
Trailer hitch Class III mounted rear, optmized mounting to be in a raised mounting position.
Step bars will be located under the entry doors of the cab each side. Bars will have a stainless finish.
Driveline guards (as applicable).
Diesel Exhaust Fluid (DEF) 5 gallon tank for 2013 / 2016 EPA engines. Location: [#LOC].
Diesel Exhaust Fluid (DEF) 10 gallon tank for 2013 / 2016 EPA engines. Location: [#LOC].
Officer side rear underbody Class III hitch receiver. Includes Class III trailer receiver, (1) officer side facing side for portable winch receiver with an electrical connection for winch.
Seperate PTO for aerial hydraulic pump IPO shared system.
Cab windows to be power operated. Two (2) door International (International code 16WJU) Tradition.
Insta‐chain tire chain installation. Includes 12 chain sytem. Requires pre‐wire option located in Cab Electrical.
Exhaust extension and reinforcement to allow the exhaust to extend 35" above the engine cover.
Additional metal placard on officer front cab door of Timmoney diagram showing points.
Air control panel for a chassis air outlet in compartment L2. The panel shall have quarter turn shut off valve, 0‐300 pounds per square inch air pressure gauge, 0‐125 pounds per square inch pressure regulator and a check valve in the supply line.
Upgrade pressure side power steering hoses with steel braided line in lieu of nylon braided.
On‐Spot tire chain to be supplied and installed by commercial chassis supplier. Requires engineering review and approval if less than 180" WB.
Smooth plate trim package with black durabak finish for a (4) door International. Includes a full length driver side and a (2) piece officer side trim that will utilize pieces already supplied by the OEM, will include modfication for booster reel(s).
Tow eyes front painted through bumper / cab (PR). Eyes to be 1" thick material.
Plumb Vogel lube system to On‐Spot tire chains.
Additional engine insulation under cab. Includes forward and rearward cab areas. See Engineering for installation instructions.
On‐Spot tire chain installation. Includes 12 chains per wheel. Requires pre‐wire option located in Cab Electrical. Requires engineering review and approval if less than 180" WB.
Under the body there shall be equipped with a pair of receiver assemblies, each with a removable swivel hoist ring and chrome tow hooks (1) each side to act as tie down points. One each side of apparatus. The receivers shall be square steel tubing, same size as a receiver for a Class III trailer hitch. Located to rear of front outriggers.
Steel tow bar located below rear compartment mounted to chassis frame for towing purposes only, painted black.
Tow eyes rear below body, painted. 1" thick material with 3" diameter hole staight down from chassis frame.
Radiator mounted power steering cooler.
Power windows and door locks. Freightliner 2‐Door. Tradition.
Tow eyes front painted in down position with additional officer only in the up position.
Tow eyes front painted bright silver through bumper / cab (PR).
Oil pan heater for ISL engine. Fleetguard 22MM 150W/120V wired to winterization shoreline receptacle.
Block heater to be wired through [#LOC].
Bevel interior holes of front and rear tow eyes.
PRICE
$0.00
$1,036.00
$1,722.00
$965.00
$1,834.00
$1,917.00
$1,001.00
$2,076.00
$294.00
$3,106.00
$409.00
$170.00
$979.00
$50.00
$0.00
$5,655.00
$552.00
$212.00
$1,495.00
$3,190.00
$3,726.00
$1,962.00
$777.00
$514.00
$150.00
$423.00
$552.00
$515.00
$0.00
$516.00
Option No.
1680‐0291
1680‐0292
1680‐0293
1680‐0294
1680‐0295
1680‐0299
1680‐0300
1680‐0302
1680‐0303
1680‐0306
1680‐0311
1680‐0312
1680‐0313
1680‐0316
1680‐0319
1680‐0320
1680‐0321
1680‐0326
1680‐0327
1680‐0328
1680‐0329
1680‐0330
1680‐0331
1680‐0332
1680‐0334
1680‐0336
1680‐0338
1680‐0344
Description
Tow forks under front bumper extension.
Auto lube system CPL. Chassis points only.
Tow hooks front painted in the outboard position.
Tow eyes rear frame painted. Eyes to be angled downward thru the rear body skid plate. Design to accommodate a rear body max departure angle modification.
Trailer hitch Class I receiver mounted rear.
Trim Package to be used with 4 door Freightliner M2 series chassis.
Steel lift bar located below rear compartment mounted to chassis frame for lifting purposes only (no towing), painted black.
Steel tow/lift bar located below rear compartment mounted to chassis frame, painted black.
Splash guard for reel below front of cab. Includes chute to front bumper tray for hose. Hush chassis only.
Air intake emergency shut‐down. Pump panel mounted guarded switch with reset switch located below front bumper.
Fan drive w/thermatic clutch permanently engaged.
On‐Spot tire chains. Includes switch in cab.
Power Mirrors 600, Disc Brakes 800, Air seat and additional battery modification 1,800, Mirror mounted turn signals 650, Two Tone paint 651
CPL auto lube system for chassis points (up to 26) and jack system points (12).
Tow eyes front painted below bumper/cab pointed forward. (PR). Custom chassis only.
Weather resistant box for tire chain solenoid.
Steel tow/lift bar located below front of cab mounted to chassis frame, painted black.
Side 9K Winch Receivers ‐ frame rail height shall be provided. Two (2) winch receivers, one (1) each side, shall be located in line with the top of the frame rail ahead of the rear wheels. Each receiver position shall have its own pin. Winch receiver(s) shall be rated for a maximum of 9,000 line pull pounds with a 2.0 to 1 straight line pull no‐yield safety factor. 12VDC power and exterior doors not included.
Block heater 1500 watt wired through APU. Available on ISM, ISX and S60 only.
Oil pan heater ‐ Fleetguard 450W/120V wired to APU only. ISX only.
Air clutch for second hyd pump. For use with dual hyd pump systems on a single PTO. Requires first hyd pump to be drive‐thru style.
Receiver, side body 9K Winch Receivers‐frame rail height shall be provided for use with Reyco suspension. Two (2) winch receivers, one (1) each side, shall be located in line with the top of the frame rail ahead of the rear wheels. Each receiver position shall have its own pin. Winch receiver(s) shall be rated for a maximum of 9,000 line pull pounds with a 2.0 to 1 straight line pull no‐yield safety factor. 12VDC power and exterior doors not included.
Tow eyes front painted job color mounted in up position. Requires 16" minimum bumper extension on custom chassis and 18" minimum bumper extension on commercial chassis.
Radiator overflow lines to be extended below frame rails and secured with metal clamps.
Oil pan heater ‐ Fleetguard 450W/120V wired to block heater receptacle. ISX only.
Special transmission lock bracket for manual transmission and electrical programming.
Extensions for chassis and cab tilt grease fittings. Extensions to be routed to three groups (left front, right front and rear).
Tow eyes front painted in down position with additional stainless steel officer only in the up position.
PRICE
$699.00
$4,643.00
$293.00
$772.00
$633.00
$2,799.00
$1,962.00
$3,132.00
$903.00
$1,933.00
$1,506.00
$3,082.00
$0.00
$8,504.00
$1,965.00
$122.00
$4,986.00
$3,090.00
$555.00
$570.00
$3,967.00
$3,090.00
$422.00
$0.00
$570.00
$721.00
$983.00
$638.00
Option No.
1680‐0345
1680‐0349
1680‐0350
1680‐0351
1680‐0352
1680‐0353
1680‐0356
1680‐0360
1680‐0361
1685‐0000
1685‐0001
1685‐0002
1685‐0003
1685‐0004
1685‐0005
1685‐0006
1685‐0008
1685‐0009
1685‐0011
1685‐0012
1685‐0013
1685‐0015
1685‐0016
1685‐0017
1685‐0018
1685‐0019
1685‐0020
1685‐0022
1685‐0023
1685‐0024
Description
Tow eyes rear frame painted. Locate: B1, inside with eye plates spaced to best accommodate common sized towing hardware inside the compartment.
Tow eyes rear below body, painted. 1" thick material with 3" diameter hole staight down from chassis frame. For use as lifting eyes at rear of chassis.
Receivers, side body 9K winch receivers ‐ frame rail height shall be provided. Two (2) winch receivers, one (1) each side, shall be located in line with the top of the frame rail between rear tandem wheels. Each receiver position shall have its own pin. Winch receiver(s) shall be rated for a maximum of 9,000 line pull pounds with a 2.0 to 1 straight line pull no‐yield safety factor. 12VDC power and exterior doors not included.
All applicable .625" heater hose to have constant torque clamps. Includes end, union and T‐fittings.
Side underbody 9K winch receivers. Includes (2) side facing‐ (1) each below body compartment offset forward on tiller trailer body for portable winch with electrical connection for winch.
Heavy duty frame cross‐member located at cab locks.
Rope tie off. Side underbody Rope Tie Off. Includes (2) side facing‐ rope tie off points (1) each below body located per engineering approval. Rating: 1000 lbs with 10:1 safety factor with straight line pull.
Bevel interior holes of rear tow eyes.
Tow eyes rear frame stainless steel with 4" holes.
Cab interior gray. Does not include engine cover or seat color.
Cab interior black. Does not include seat color.
Cab interior burgundy. Does not include engine cover or seat color.
Fold down computer tray bolted to engine cover on officer's side.
Storage below rear bench seat for four SCBA bottles.
Lexan sun visors, driver and officer's side overhead.
Padded sun visors, driver and officer's side overhead.
Control lanyard Y type for air horns.
Chain for ignition key
Stainless steel pair of window bars for rear cab doors.
Seating capacity tag of two occupants.
Console control Ford chassis
Locking Gun Box
Three Ring Binder/VCR mount
Overhead Glove Box constructed of ABS plastic
Gun box aluminum with a Simplex lock.
Cab Handrail Floor to Ceiling (PR) to assist entry and exit of vehicle
Maplight 20" gooseneck on driver and officer side of console.
Lateral "G" Alert system with audible and visual warnings.
Inclinometer, phosphorescent illumination with 20‐0‐20 side slope indicator.
Cab Floor Mod ‐ Crown
PRICE
$829.00
$1,845.00
$3,390.00
$357.00
$1,661.00
$1,028.00
$1,995.00
$258.00
$1,720.00
$0.00
$375.00
$3,086.00
$799.00
$727.00
$0.00
$0.00
$186.00
$139.00
$407.00
$0.00
$512.00
$612.00
$593.00
$569.00
$593.00
$143.00
$75.00
$3,435.00
$197.00
$0.00
Option No.
1685‐0026
1685‐0027
1685‐0028
1685‐0029
1685‐0030
1685‐0031
1685‐0032
1685‐0033
1685‐0034
1685‐0035
1685‐0036
1685‐0037
1685‐0038
1685‐0039
1685‐0040
1685‐0041
1685‐0045
1685‐0046
1685‐0047
1685‐0050
1685‐0051
1685‐0052
1685‐0054
1685‐0056
1685‐0057
1685‐0058
1685‐0059
1685‐0060
1685‐0061
1685‐0062
1685‐0063
1685‐0064
1685‐0066
1685‐0068
Description
Door Seat Riser Ovrlap drv/off for the Typhoon only.
Heater rear cab w/o cover (PR). 23,000 BTU ea.
Heaters rear cab w/covers (PR).
OEM Seat Center Section Removed Light Duty
Seating capacity tag of three occupants.
Seating capacity tag of four occupants.
Seating capacity tag of five occupants.
Seating capacity tag of six occupants.
Seating capacity tag of seven occupants.
Seating capacity tag of eight occupants.
Seating capacity tag of nine occupants.
Seating capacity tag of ten occupants.
ALS Prov w/Ext Access Drs
Window bars stainless steel pair for canopy windows.
Cut out in rear cab wall to enable walking into the body.
Label Package‐ Seat number, 2 person cab ‐ Overall height ‐ "No Ride"
Single headset hook hanger above cab seat.
Maplight 360 degree directional interior fwd upper cab area foward driver and officer.
Speedometer gauge with odometer KPH only.
Modify rear bench seat riser to have storage access from each side for (4) SCBA bottles, (2) ea side. Hinge doors as to work best with rear heater locations.
Speedometer with odometer dual gauge english standard (MPH dominate).
Headset Hook Hanger Rack with 4 Hooks installed on rear wall of cab.
Trim cab door kickplate 4 door.
Heater rear cab w/o cover (PR) and front cab heater with heat to the feet for the driver and officer.
Heaters cab rear with covers (PR), and front heater with heat to the feet for the driver and officer.
Interior cab access panel. Driver side of cab for access to rear of shore line receptacle. Panel to be 8" x 8".
Locking seat riser door. Driver and officer seat riser doors are to include a locking push‐button latch. Key type to be 1250.
Louvers in rear bench seat riser. For ventilation.
Interior cab access panel. Officer side of cab for access to rear of shore line receptacle. Panel to be 8" x 8".
Label package for Memphis units only, to include labeling of items behind all removable panels and check loose items in cab warning labor for off side dash and cab tilt access door.
Medical glove box. Mount to rear area of engine cover. Includes slotted top for dispensing gloves without opening hinged lid. Box to be same color as interior of cab. Secure lid in closed position with small butterfly latch.
Embossed diamond plate foot plates located at driver, officer and rear facing seat positions where feet would rest while seated.
Officer seat riser storage compartment door to be on front of riser hinged towards engine cover.
Rear engine cover diamond plate trim.
PRICE
$211.00
$1,621.00
$1,731.00
$295.00
$0.00
$0.00
$0.00
$0.00
$0.00
$0.00
$0.00
$0.00
$3,667.00
$407.00
$1,933.00
$0.00
$28.00
$114.00
$181.00
$1,695.00
$132.00
$154.00
$0.00
$1,621.00
$1,731.00
$329.00
$163.00
$168.00
$329.00
$563.00
$273.00
$305.00
$192.00
$235.00
Description
Hinged interior cab gauge panel in front of driver. Includes (9) gauges‐ English dominant. Panel to be hinged for access to driver gauge cluster.
Lanyard "Y" control. Chassis mounted air horn(s). Commercial chassis.
Notch cab wheel well and engine cover to provide 40 inches from rear wall to engine cover
There shall be no E‐One logos on cab seats.
Control lanyard Y type or dual single pull as applicable for air horns on a commercial chassis.
Communications cabinets (1/8"). 20.5"W x 16"H x 20"D INT (PR). Includes (2) roll out trays and vertically hinged door (1/8") with thumb latch. Location: One each side over cab wheel wells. Includes a smooth plate cover with matching cab finish for customer installed wiring between towers.
Removable ABS panel 35"H x 4.5"W for officer side cab wall to route communication wires from officer side communication cabinet to officer side dash area. Panel to be attached with screws.
Unitrol and EQ2B sirens to operate only with Master Warning Light switch and Primary Warning Light are ON.
Ground Light switch to operate all ground lights and step lights.
Kick Plate in front of the officer to be diamond plate.
Tag to indicate Combination Vehicle Weight, Gross Axle Weight, and Gross Vehicle Weight shall be located in the cab.
PRICE
$381.00
$273.00
$100.00
$362.00
$1,336.00
1685‐0092
1685‐0093
1685‐0094
1685‐0095
1685‐0100
1685‐0101
Embossed diamond plate foot plates located at driver, officer and forward facing rear seat positions where feet would rest while seated.
3/16" Aluminum plate on top engine access door. To have swirl finish and be spaced up approx 1/2".
Center cab dash electrical panel to be held in place with coin slot style fasteners.
Stainless steel scuff plate under interior canopy window.
Rear engine cover radio cabinet. Cabinet to have access from the top and from rear with swirl and clear coat finish.
Removable ABS panel 35"H x 4.5"W for driver side cab wall to route communication wires from driver side communication cabinet to driver side dash area. Panel to be attached with screws.
Louvers for officers seat riser. Locate louvers in the front, side and door of riser (as applicable).
Rear cab headliner to be six pieces IPOS.
Mount customer supplied computer tray on engine cover. Includes support plates on the top and bottom.
Mount (2) intermediate steps to be bolted‐on (one each side) inside the front driver and officer cab step well drawing # 672433 and 672434.
Black rubber handrail mounted parallel to seats on rear of engine cover for driver and officer rear facing seats.
Storage below rear bench seat. (1) horizontal hinged door on the front of the rear bench seat.
Locking rear seat riser door (PR). Seat riser doors are to include a locking push‐button latch. Key type to be 1250.
Tag cab hatch to read "EMERGENCY ESCAPE HATCH"
Rear engine cover radio cabinet. Cabinet to have access from the top and from rear with OTO finish.
1685‐0104
1685‐0105
Map pockets 14 gauge stainless steel (PR). Includes vinyl trim around top of opening and nylon strap with snap to retain contents. Locate pockets one each side on rear cab wall centered between center cabinet and side wall of cab with bottom approx 20'' above floor.
Sun visor strap (PR) with snap fasteners.
Option No.
1685‐0069
1685‐0070
1685‐0071
1685‐0072
1685‐0073
1685‐0074
1685‐0075
1685‐0076
1685‐0077
1685‐0078
1685‐0079
1685‐0080
1685‐0084
1685‐0085
1685‐0086
1685‐0087
1685‐0088
1685‐0089
1685‐0090
1685‐0091
$2,297.00
$175.00
$511.00
$2,219.00
$267.00
$2,811.00
$121.00
$0.00
$0.00
$156.00
$50.00
$121.00
$369.00
$281.00
$245.00
$203.00
$196.00
$468.00
$163.00
$18.00
$727.00
$440.00
$152.00
Option No.
1685‐0106
1685‐0107
1685‐0108
1685‐0109
1685‐0110
1685‐0111
1685‐0112
1685‐0113
1685‐0114
1685‐0115
1685‐0116
1685‐0117
1685‐0118
1685‐0119
1685‐0120
1685‐0121
1685‐0123
1685‐0124
1685‐0125
1685‐0126
1685‐0127
1685‐0128
1685‐0130
1685‐0131
1685‐0133
1685‐0134
1685‐0135
1685‐0136
1685‐0137
1685‐0138
1685‐0139
1685‐0140
1685‐0141
Description
Rear engine cover radio cabinet. Cabinet to have access from the top and from rear.
Interior grab handle rubber covered (2). Locate one each side at interior of rear cab door opening (at rear of opening).
Locking seat riser door. Driver and officer seat riser doors are to include a locking push‐button latch. Key type to be CH‐751.
Locking rear seat riser door (PR). Seat riser doors are to include a locking push‐button latch. Key type to be CH‐751.
Storage below rear bench seat for two SCBA bottles (one each side).
Rear cab interior wall overlay with swirl and clear coat finish.
Integrated Roll Sensor (IRS) for RollTek air bag system.
Integrated roll sensor slave module for RollTek air bag system.
Integrated Head Curtain (IHC) for RollTek air bag system.
Integrated Belt Pretensioner (IBP) for RollTek air bag system.
Interior grab handle rubber covered (2). Locate one each side at interior of front cab door opening (at rear of opening).
Rear cab interior wall overlay with Zolatone finish.
Pump operator panel on rear wall of cab. For use with Class 1 TME pump panel. Final design to be determined by E‐ONE Applications and Chassis Engineering and with Class 1.
3/16" Aluminum plate on top engine cover forward of access door. To have swirl finish and be spaced up approx 1/2".
Rear cab interior wall overlay with diamond plate finish.
Flat bar (.5" x 2") installed on rear cab wall up high with full length shelf track.
Friehgtliner provided Interior Convenience Package which includes; Driver and officer dual reading lights forward of cab roof, Roof mounted console with upper storage compartments and center compartments without netting, Main heater upgrade, Molded door panel with upper vinyl insets, Wood grain driver and center instrument panel.
Freightliner provided Auxiliary Heat and Air Conditioner with Constant Temperature Control and Ducting in Rear of Chassis.
Canadian Domiciled Commercial Chassis includes: Dual Read Metric Dominate Gauge Cluster.
SCBA Storage tubes (4) horizontally mtd (2) each side in lower rear cab compartments above floor level.
Locate rear cab heaters below front of rear wall seat riser(s). Includes louvers for ventilation.
Freightliner provided Power Window and Door Locks.
Oval label 2.362"H x 3.029"L to be applied to interior of windshield upper right hand corner, officer's side. Label to read "CCC" "F".
Reinforcement plate(s) behind lower rear cab wall padding. TME only.
Intercom control panel shield installed on console, below plastic fascia, flush with switch ends.
Embossed diamond plate foot plates located at each seating position where feet would rest while seated.
Hot climate insulation package. Includes insulation for ceiling, front wall, rear wall, side walls, below seat risers, and in doors.
Storage in rear wall free standing seat riser. (1) horizontal hinged door on the front of the free standing seat riser.
Console Remote Control Panel between Driver and Officer for remote control Bumper Turret, Pump Control, and switchs.
3/16" Aluminum plate on top engine cover forward of access door. Finish to match cab interior and be spaced up approx 1/2".
3/16" Aluminum plate on top engine access door. Finish to match cab interior and be spaced up approx 1/2".
Storage at rear engine cover w/ cargo net top. (3) sided storage approx. 44.5"W x flush with upper engine cover high x sloped area of engine cover deep. Storage area to match cab interior.
Main control console. Locate in cab centered between driver and officer. Includes all primary in‐cab controls/switching.
PRICE
$727.00
$226.00
$86.00
$86.00
$727.00
$734.00
$2,355.00
$1,096.00
$663.00
$385.00
$226.00
$478.00
$2,228.00
$273.00
$601.00
$337.00
$225.00
$475.00
$0.00
$848.00
$397.00
$950.00
$0.00
$626.00
$141.00
$305.00
$2,488.00
$363.00
$913.00
$273.00
$273.00
$796.00
$0.00
Option No.
1685‐0142
1685‐0143
1685‐0144
1685‐0146
1685‐0147
1685‐0148
1685‐0149
1685‐0150
1685‐0151
1685‐0152
1685‐0153
1685‐0154
1685‐0155
1685‐0156
1685‐0157
1685‐0158
1685‐0159
1685‐0160
1685‐0161
1685‐0162
1685‐0163
1685‐0164
Description
Main control console. Locate in cab centered between driver and officer. Includes NFPA in‐cab controls/switching.
Cab gauge cluster with english dominant.
Cab gauge cluster with metric dominant.
Extended electrical access panel in cab. Panel to extend up to allow for radio/equipment installation.
Narrow rear cab wall support channel. Not available with non‐ABTS rear wall seating.
Rear cab wall pump operator console. Includes lower pedestal mount (job color of interior of cab) with access panel and stainless steel control panel. Panel to fixed with area for recessed panel lighting.
Cut out in rear cab wall to enable walking into the body. Commecial chassis only.
The cab walls and ceiling shall be insulated. The interior cab ceiling and walls shall have interior padding and ABS panels applied to the metal surfaces as applicable. ICAO Only.
Main control console. Locate in cab centered between driver and officer. Includes NFPA in‐cab controls/switching and mounting for EQ2B siren control head..
Main control console. Locate in cab centered between driver and officer. Includes NFPA in‐cab controls/switching (note style of switching and requirements for front preconnect controls and gauge). Exterior finish (including top surface) to be black powder coated.
Storage below rear bench seat. (2) horizontally hinged doors on the front of the rear bench seat.
Communications cabinets (1/8"). 20.5"W x 16"H x 20"D INT (PR). Includes (2) roll out trays and cargo netting over openings. Location: One each side over cab wheel wells. Includes a smooth plate cover with matching cab finish for customer installed wiring between towers.
Cold climate insulation package. Includes insulation for ceiling, front wall, rear wall, side walls, below seat risers, and in doors.
Command desk, rear engine cover 5"H x 17"D x full width between medical cabinets. Desk to include hinged aluminum lid with lexan overlay and gas shock, trigger latches, 1" return lip on lid and 1" back splash. Desk to be mounted 26" off of floor with finish to match cab interior.
Dash label "Switch Compression Brake Off for Wet or Slippery Road Conditions".
The cab floors shall be insulated. Interior matting shall be applied to the metal floor surfaces.
Vehilce meets NFPA Complinace with exception to the Laterial "G" Alert System.
E‐One supplied/Van‐Mor installed Swivel Pedestal Seat. Locate in cab command area in front of desk. If more then one seat offset them.
Severe duty dash package. Includes smooth plate alum center and officer side dash painted to match cab interior and lower dia plt kick panels.
Severe duty engine cover. Includes floor type matting on sides, top forward and top rearward engine covers with sanded finish smooth aluminum trim.
Swivel Pedestal Seat. Locate in cab command area in front of desk. If more than one seat, offset them. The seat will include seat belts. Only when the seat is locked, facing the driver's side can the seat be a transit seat. Seat color will match the interior of the front cab seats.
Severe duty engine cover. Includes floor type matting on sides, top forward and top rearward engine covers with smooth aluminum trim painted to match cab interior.
PRICE
$0.00
$0.00
$308.00
$627.00
$232.00
$1,753.00
$3,229.00
$1,454.00
$0.00
$0.00
$934.00
$2,811.00
$2,488.00
$2,357.00
$52.00
$933.00
$0.00
$549.00
$1,003.00
$1,086.00
$1,919.00
$1,276.00
PRICE
1685‐0181
Description
Storage below rear bench seat. (1) horizontally hinged door on the front of the rear bench seat. Hinge hardware mounted with acorn nuts outside.
Driver side command desk in cab. Desk will run from back of drivers seat to the back wall of the cab. There will be a raceway on the back side of the desk with a removable plate for access to interior of race way. Desk will have a 2" lip down with a 1" lip back. All items are to have a DA finish.
Provide (2) two overhead storage compartment with plexi glass doors above the desk top installed on the upper portion of the interior. Locate in the cab interior in Vista area. Cabinet shall be made out of aluminum with plexi glass sliding doors. Each cabinet shall have a DA finish. The doors should slide side to side allowing access to one side at a time. Each cabinet shall be approx 14" deep x 14" high x as long as needed in the vista area.
ABS Dash package. Includes center and officer side dash, lower kick panels and "A" post covers.
Typhoon engine cover ‐ Thermoformed ABS / molded polyurethane.
Cyclone II engine cover ‐ Molded polyurethane.
Speedometer with odometer dual gauge metric (KPH) dominate.
Storage below rear bench seat. (1) hinged door on each front corner of the bench seat base.
Main control console for Ford chassis. Locate in cab centered between driver and officer. Includes all in‐cab controls/switching.
Louvers for rear bench seat riser. Locate louvers on each side of riser.
Provide (1) one overhead storage compartment with plexi glass doors above the desk top on the driver's side installed on the upper portion of the interior. Locate in the cab interior in Vista area. Cabinet shall be made out of aluminum with plexi glass sliding doors. Each cabinet shall have a DA finish. The doors should slide side to side allowing access to one side at a time. Each cabinet shall be approx 14" deep x 18" high x as long as needed in the vista area.
Insulation ‐ front cab wall. Includes insulation on rear cab heater hose lines (if equipped). Custom ES.
Cab gauge cluster with metric dominant speedometer.
Cab gauge cluster with english dominant.
Locate rear cab heaters below top mount pump panel on rear cab wall. Includes louvers as applicable.
On Scene Solutions Talon helmet holder (EA). Location: [#LOC].
Pump operator panel on rear wall of cab. For use with TME pump panel. Final design to be determined by E‐ONE Applications and Chassis Engineering
1685‐0182
1685‐0183
1685‐0184
1685‐0185
1685‐0186
1685‐0187
1685‐0188
1685‐0190
1685‐0191
Severe duty dash package. Includes smooth plate alum center, officer side dash and lower kick panels; all painted to match cab interior.
Heater cab with heat to the feet for the driver and officer
Heater rear cab w/o cover. Includes 110V blower.
Locking rear seat riser door. Seat riser door to include a locking push‐button latch. Key type to be 1250.
Storage box to hold four (4) helmets mounted in the center of the rear wall.
Severe duty engine cover, molded polyurethane.
Stainless steel trim low on officer side of engine cover (to match driver side). CII / Typhoon only.
ABC Extinguisher 10#. Locate bracket [#LOC].
Diamond plate cover for battery charger/air compressor. Includes louvers for ventilation.
$1,003.00
$846.00
$1,346.00
$163.00
$789.00
$0.00
$140.00
$178.00
$238.00
Option No.
1685‐0165
1685‐0166
1685‐0167
1685‐0168
1685‐0169
1685‐0170
1685‐0171
1685‐0172
1685‐0173
1685‐0174
1685‐0175
1685‐0176
1685‐0177
1685‐0178
1685‐0179
1685‐0180
$468.00
$1,749.00
$2,353.00
$0.00
$0.00
$0.00
$139.00
$892.00
$638.00
$369.00
$4,706.00
$113.00
$308.00
$0.00
$397.00
$426.00
$2,228.00
Option No.
1685‐0192
1685‐0193
1685‐0194
1685‐0195
1685‐0196
1685‐0197
1685‐0198
1685‐0199
1685‐0200
1685‐0201
1685‐0202
1685‐0203
1685‐0204
1685‐0205
1685‐0206
1685‐0207
1685‐0208
1685‐0211
1685‐0212
1685‐0213
1685‐0215
1685‐0216
1685‐0217
1685‐0218
1685‐0219
Description
PAC TRAC panels vertical stacked with tool mounting grooves orientated horizontal on back wall of cab each side outboard of bench seat.
Slide‐out MDT mount officer cab dash. Requires severe duty dash w/MDT notch.
Officer cab dash modification for Havis slideout MDT bracket. Not available with heat to feet or side roll protection.
Control lanyard to officer side and located over the officer side door opening with a single chain. For use with air horns. Commercial chassis only.
Severe duty Quest officer dash package. Includes smooth plate alum officer side dash with trim panel painted to match cab interior and lower dia plt kick panel.
Rear upper cab interior wall 3/16" overlay with Zolatone finish. Approximately 20" high.
Cab Floor Mod ‐ Extnd Box Type. For use with short cab application and battery relocation on top of chassis frame rails. Floor mod to extend to rear cab wall.
Rear engine cover brushed stainless steel trim.
(No longer used. Please see 1685‐0193) Slideout MDT mount officer cab dash. Requires severe duty dash w/ MDT notch. Not available with heat to the feet.
Severe duty dash package. Includes smooth plate alum center and officer side dash painted to match cab interior and lower dia. plt. kick panels. Officer cab dash notched for MDT slide‐out bracket(s).
"Y" type lanyard control for air horns. Lanyard is in addition to the foot switch controls. Custom ES.
A grab handle for the crew member at each seated position.
Side mount telescopic computer tray bolted to engine cover on officer's side.
Storage at rear engine cover w/ drop down rear door. (3) sided storage approx. 44.5"W x flush with upper engine cover high x sloped area of engine cover deep with (2) equally spaced vertical dividers. Storage area to match cab interior.
Center control console. Locate in cab between driver and officer. Includes area for NFPA siren, electrical, and in‐cab controls (as applicable) switching.
Cup holders; severe duty dash. (1) each side facing of center electrical cover; driver offset rearward, officer offset forward. Holders to match cab interior.
The interior dash panels to be burl wood in place of standard. Kenworth
Center control console. Locate in cab between driver and officer. Includes area for NFPA siren, electrical, and in‐cab controls (as applicable) switching.
Commercial chassis to have a pair of defogger fans.Ordered with chassis.
Cab interior door NFPA reflective material to be mounted to .090 material panels IPO door plastic. Size panels as applicable to lower door
surface for best securing to door.
Rear cab SCBA mounting brackets (2) with holders, Wildland.
Rear Bench Seat Base Enclosure, Wildland, Navistar
Main control console. Locate in cab centered between driver and officer. Includes NFPA in‐cab controls/switching.
KNOX‐BOX KeySecure model 2642. Includes E‐ONE installed wiring to switched 12v power supply. Location: officer side of engine cover. Requires dept to purchase software package from KNOX‐BOX (if they do not already have it).
Interior grab handle rubber covered (2). Locate one each side at interior of rear cab door opening (at front of opening).
PRICE
$1,552.00
$1,137.00
$492.00
$267.00
$419.00
$383.00
$0.00
$495.00
$663.00
$1,222.00
$144.00
$56.00
$989.00
$796.00
$1,727.00
$246.00
$155.00
$2,231.00
$0.00
$0.00
$1,236.00
$1,000.00
$0.00
$1,295.00
$226.00
Option No.
1685‐0220
1685‐0221
1685‐0222
1685‐0223
1685‐0224
1685‐0225
1685‐0226
1685‐0227
1685‐0228
1685‐0229
1685‐0230
1685‐0231
1685‐0232
1685‐0233
1685‐0234
1685‐0235
1685‐0236
1685‐0237
1685‐0238
1685‐0239
1685‐0240
1685‐0241
1685‐0242
1685‐0243
1685‐0244
1685‐0245
1685‐0246
Description
KNOX‐BOX SentraLok A Model 3923 with red strobe. Includes E‐ONE installed wiring to switched 12v power supply. Location: left side of officer dash. Requires dept to purchase software package from KNOX‐BOX (if they do not already have it).
Severe duty dash package. Includes smooth plate alum center and officer side dash painted to match cab interior and lower dia plt kick panels. Officer cab dash notched with recessed glove box. Includes angled notepad holder on top. Not available with Rolltek.
Storage at lower rear engine cover w/ cargo net top. Approx. 30"W x 12"H x sloped area of engine cover deep. Storage area to match cab interior.
Storage at rear engine cover w/ lift‐up door. Storage approx. 44.5"W x flush with upper engine cover high x sloped area of engine cover deep. Storage area to match cab interior.
[#COL] vinyl cover for steering wheel shaft at driver's position.
Storage at rear engine cover w/ lift‐up door. Storage approx. 37.5"W x flush with upper engine access cover high x 34" deep (front to rear). Includes forward 12" stationary cover. Storage area to match cab interior.
Cab interior tactical equipment storage module, painted black durabak. Includes removable un‐painted radio shelf.
Critical tags shall be upgraded to embossed metallic tags fastened in place with stainless steel hardware.
Cab floor shall be upgraded to be made of embossed diamond plate IPO standard diamond plate.
Southco model C2‐32‐21‐3 keyed latch for electrical access door in cab dash. Severe duty dash only.
The multiplex display shall be angled towards the driver.
Aluminum front headliner backing plates in place of standard material.
Embossed 3/16" diamond plate floor overlay for driver and officer side floor.
Computer mount located on the mounting plate ahead of the engine access cover. Includes bracket models C‐MD‐202, C‐HDM‐134, dock station DS‐PAN‐211‐2, power supply LPS‐101, keyboard mount KM‐NY and stiffener DS‐DA‐405.
Cup holders; severe duty dash. (1) each side of forward engine cover. Holders to match cab interior.
Foot switch Linemaster model 632S to control air horns located [#LOC]. Includes 25 degree diamond plate bracket.
Cab steps and bolt‐on steps (if applicable) (excluding ALS step if provided) to be equipped with Bustin Industries Type M stainless steel overlay in lieu of Gator Grip. Includes (6) 3/4" drain holes on the lower steps.
KNOX‐BOX KeySecure model 2642. Includes E‐ONE installed wiring to switched 12v power supply. Location: officer side cab dash inboard. Severe duty dash only. Requires dept to purchase software package from KNOX‐BOX (if they do not already have it).
Insulation ‐ front cab wall. Includes insulation on rear cab heater hose lines (if equipped).
PRICE
Cab floor to be overlayed with 1/8" embossed aluminum diamond plate; front and rear. Single piece with no gaps around perimeter.
Slide‐out MDT mount officer cab dash with dock. Requires severe duty dash w/MDT notch. Not available with heat to the feet.
Locate rear cab heaters one each side rear cab wall down low.
Officer seat riser storage compartment door to be hinged to the rear.
Pac Trac panels vertically stacked on back wall of cab each side outboard of medical cabinet.
Mechanical fastners ipos for headliners.
Main control console for Ford chassis. Locate in cab centered between driver and officer. Includes all in‐cab controls/switching. Console to have a Zolatone gray finish.
Maplight flexible LED on driver and officer side of console.
$994.00
$1,559.00
$0.00
$117.00
$1,552.00
$197.00
$1,809.00
$1,475.00
$796.00
$796.00
$54.00
$1,103.00
$2,219.00
$251.00
$280.00
$148.00
$129.00
$219.00
$305.00
$1,741.00
$246.00
$125.00
$1,804.00
$1,295.00
$113.00
$638.00
$148.00
Option No.
1685‐0247
1685‐0248
1685‐0249
1685‐0250
1685‐0251
1685‐0252
1685‐0253
1685‐0254
1685‐0255
1685‐0256
1685‐0257
1685‐0258
1685‐0259
1685‐0260
1685‐0261
1685‐0262
1685‐0263
1685‐0264
1685‐0265
1685‐0266
1685‐0267
1685‐0268
Description
Cab floor to be overlayed with 1/8" embossed diamond plate; front and rear. Single piece with no gaps around perimeter. Front plates to be sand blasted to remove shine.
Storage box with diamond plate hinged top with push‐button latch. Box to be mounted on floor centered of rear wall. Size: 36H x 40W x 20D. Finish to match can interior (excluding lid). Includes compt light to match body package.
Label to read "CYCLONE II X036". Location: inside driver door jamb.
Main control console. Locate in cab centered between driver and officer. Includes NFPA in‐cab controls/switching.
Diamond plate cover to protect the steering wheel shaft/knuckle.
Storage cabinet center rear crew area. Box to be installed from behind engine cover to rear wall with open sides and (1) adjustable shelf. Sides will be provided with cargo net covers. Handrails provided on each side top of cabinet. Cabinet to match cab interior.
Reinforce all anchor points on overhead console panels.
Storage box locking, mounted on the rear lower engine cover. Engine cover lock box measures 18x24x9 with a lift top lid and a locking latch. Finish will match cab interior.
Center control console. Locate in cab between driver and officer. Includes area for NFPA siren, electrical, customer supplied radio cut‐
out and in‐cab controls (as applicable) switching.
Electrical schematic aluminum pocket behind driver seat.
Air compressor cover NYPD.
SCBA rear wall peg tool board mount for three (3) Lifeguard Smart Dock 2 SCBA brackets. The "peg board" SCBA tool board shall be mounted between the two (2) rear outboard seats with adequate room between each pack to mount complete SCBA packs. Peg board sizing shall be approximately 40" wide X 35" high and shall be spaced off the rear wall approximately 1". The peg board shall be finished with Zolotone.
Jotto AK‐12, Unit No. 6159 main control console for Ford chassis. Locate in cab centered between driver and officer. Includes all in‐cab controls/switching and laptop mounting surface.
Label package for NYPD units only, to include seating capacity labels in yellow with black lettering; (1) each side of overhead console. "Tower Up" label black with white lettering above tower ajar light. "Master Battery" label yellow with black lettering and "Emergency Start" label black with white lettering above cole hersee switches. "Do Not Grab To Adjust" label black with white lettering in lower mirror glass. O.A.H. 11' in 2" white vinyl on driver side of windshield on radius to not interfere with driver's view.
Storage below rear bench seat. (1) cargo net (black) on each side of the bench seat to gain access to storage area.
Storage below rear bench seat for two SCBA bottles (driver side). Officer side to be open storage w/ door.
Severe duty dash package. Includes smooth plate alum center and officer side dash and lower kick panels; all painted to match cab interior. Officer cab dash notched for MDT slideout bracket(s).
A universal laptop mount, Havis model C‐3090‐3 shall be mounted to the center console. Ford commercial chassis. Requires 1685‐0173 Ford center console.
Smooth plate cover(s) for battery charger and air compressor. These cover's shall be painted to match cab interior and shall include louvers as required for ventilation.
Bolt‐in partition wall. Locate under bench seat centered between driver and officer side.
Modify rear bench seat riser to have storage access from each side for up to (2) 20lb ABC extinguishers, (1) ea side.
NOTE: Center control console to be as close as possible as previous truck. Reference E‐One part# 564559.
PRICE
$1,187.00
$1,512.00
$0.00
$0.00
$231.00
$3,065.00
$0.00
$907.00
$1,727.00
$199.00
$281.00
$2,691.00
$1,349.00
$0.00
$648.00
$727.00
$1,222.00
$743.00
$238.00
$236.00
$1,469.00
$0.00
Option No.
1685‐0269
1685‐0270
1685‐0271
1685‐0272
1685‐0273
1685‐0274
1685‐0275
1685‐0276
1685‐0277
1685‐0278
1685‐0279
1685‐0280
1685‐0281
1685‐0282
1685‐0283
1685‐0284
1685‐0285
1685‐0286
1685‐0287
1685‐0288
1685‐0289
Description
Storage box approximately 11" wide x 10" high x 26" deep made from 1/8" diamond plate aluminum, centered on to rear cab floor. The box shall cradle (1) 2.5 gallon water fire extinguisher. The door shall be hinged with push button latches to provide easy access to the extinguisher in its stowed position stored at a slight incline within the box.
Main control console for Dodge chassis. Locate in cab centered between driver and officer. Includes all in‐cab controls/switching.
Embossed diamond plate foot plates painted with black Durabak located at each seating position where feet would rest while seated.
Cup holder (PR) with shallow tray located at front center of engine cover. Polyurethane construction for use with severe duty engine cover only.
KNOX‐BOX MedVault 2 model 5520H3S2‐4. Includes E‐ONE installed wiring to battery hot. Location: rear wall of medical cabinet. Top of compartment right hand side forward facing. Requires dept to purchase software package from KNOX‐BOX (if they do not already have it).
Plate aluminum 1/8" outboard of medical cabinet rear wall between extrusions behind padding. Plate to run from ceiling down to rear cab support bracket.
Cup holder (PR). Polyurethane construction for use in Typhoon and CII with severe duty engine cover only. Location: [#LOC].
Cab interior color definitions not already defined shall include: The use of burgundy vinyl (Van‐Mor or equivalent) for the rear wall and headliner IPOS. The center dash cluster and the center overhead dash shall be burgundy ABS panels IPOS. The dash support housing and any other Zolatone surfaces (except the engine cover) shall be Zolatone "Dark Red" 20‐78 IPOS (see separate sale codes applicable for map and medical cabinets). The engine cover shall remain black Polyurethane.
E‐ONE will supply an additional metric weight and dimensions tag on the drive seat riser.
The driver side seat riser shall include a mount for the Rhino override key. The bracket shall utilize a door spring mount casting that cradles the Rhino override wrench.
Chrome grab handle. Locate (1) on the engine cover centered between latches.
Severe duty dash upgrade package to include angled/slanted mounting surfaces IPOS.
Control lanyard type officer side only for air horns.
Slideout MDT mount officer cab dash with dock (Havis DS‐PAN‐111, C‐MD‐105‐Z, C‐HDM‐135). Requires severe duty dash w/ MDT notch. Not available with heat to the feet. To include 12 VDC electrical outlet wired to battery hot.
Pac Trac panels horizontally mounted and vertically stacked on back wall of cab.
Raceway across lower engine cover; full width of cover. Painted to match cab interior.
Cup holder / tray for engine cover painted to match cab interior. Approx 14" wide x 10" long with tapered front corners and cup holders at each rear corner. For use in Typhoon and CII with severe duty engine cover.
Control lanyard Y type for air horns. Aircraft style cable (1/8" wire cable covered with clear plastic/nylon tubing) shall be used IPOS.
Rear engine cover trim 1/8" smooth aluminum painted to match cab interior and spaced up 1/2". Includes both horizontal surfaces and angle vertical surface between horizontal surfaces.
Command desk in cab. Desk will be sized per rear engine cover area. Includes a raceway on the back side of the desk with a removable plate for access to interior of race way and a pull out drawer. All items are to have a DA finish.
Foot switch Linemaster model 632S to control Q2B siren located [#LOC]. Includes 25 degree diamond plate bracket.
PRICE
$699.00
$638.00
$429.00
$127.00
$2,820.00
$231.00
$155.00
$0.00
$37.00
$63.00
$121.00
$0.00
$186.00
$1,976.00
$1,552.00
$229.00
$434.00
$240.00
$495.00
$2,618.00
$125.00
Option No.
1685‐0290
1685‐0291
1685‐0292
1685‐0293
1685‐0294
1685‐0295
1685‐0296
1685‐0297
1685‐0298
1685‐0299
1685‐0300
1685‐0301
1685‐0302
1685‐0303
1685‐0304
1685‐0305
1685‐0306
1685‐0307
1685‐0308
1685‐0309
1685‐0310
1685‐0311
1685‐0312
1685‐0313
1685‐0314
Description
Pac Trac panels vertically stacked on back wall of cab between forward facing outboard seats.
4Front air bag system with steering wheel bag, driver knee bag and officer knee bag. Requires RollTek option.
Mount for bumper turret joystick to allow use by driver or officer. Locate on forward engine cover.
Command desk, rear engine cover with a lift‐up slanted desk top approximately 31.9" high off of floor (top of sloped writing surface) X 37.9" W (side to side centered about engine cover) X 25.2" L (front to rear). Desk to include hinged aluminum lid with Lexan overlay and gas shock, trigger latches and storage compartment below. A 1" return lip shall be included on the lid. Desk to be mounted rearward of engine cover and 3X3 posts. Finish to match cab interior.
Pre‐wire for air horns, 2 floor mounted foot switches (1) driver side (1) officer side for International 4400.
The rear wall support channel shall not include pre‐punched holes for optional seating not contained within this order.
Severe duty dash package. The officer side dash shall be lowered 2.5" below its standard height. Includes smooth plate alum center and officer side dash painted to match cab interior and lower dia. plt. kick panels. Officer cab dash notched for MDT slide‐out bracket(s). The notch position shall not be modified (only the officer side dash top). Not available with heat to the feet.
Storage at rear engine cover w/ lift‐up door. Storage approx. 36"W x flush with upper engine cover high x sloped area of engine cover deep. Storage area to match cab interior.
The cab floor shall have the pre‐punched holes for the accelerator and brake pedals modified. All brake and accelerator pedal hole cutout(s) necessary shall not be visible after the pedals have been mounted in place.
Coat hook(s), stainless steel shall be provided in the cab. Location: on the rear wall as space permits.
Hook(s), stainless steel shall be provided in the cab. Location: within easy reach of the driver's seated position.
Access below top mount enclosed pump panel on rear wall of cab for access to pump compartment.
Insulation ‐ front pump compartment access door.
Driver side "L" shape cab command desk with pull out drawer. Finish is to be swirled aluminum. No clear coating!
Rear cab floor to be overlayed with 3/16" smooth plate painted with black Durabak. No seams or gaps.
Aluminum rear headliner backing plates in place of standard material.
Storage cabinet (PR) mounted on the driver and officer wheel well 15.5X24X21. Includes (1) adjustable shelf and rear facing cargo netting.
Cup holder / tray enlarged for engine cover painted to match cab interior. Approx 19" wide x 12" long with tapered front corners and cup holders at each rear corner. For use in Typhoon and CII with severe duty engine cover.
Riser rear bench seat with provisions for rear wall heaters (if equipped). For use with flip‐up seats.
Main control console. Locate in cab centered between driver and officer. Includes NFPA in‐cab controls/switching.
Main control console with zolatone grey finish. Locate in cab centered between driver and officer. Includes NFPA in‐cab controls/switching.
Adjustable throttle and brake pedals. Includes sw accessible by driver.
Locking thumb latch on DEF tank door ipos.
Smooth plate cover for battery charger. Includes louvers for ventilation. Cover to match cab interior.
Officer wheel well cabinet (1/8"). 20.5"W x 14"H x 20"D INT. Includes (1) roll out tray with 8" sides. Rear opening will have cargo netting. Includes 1" lip around perimeter of top.
PRICE
$1,552.00
$4,692.00
$364.00
$2,467.00
$425.00
$57.00
$1,387.00
$757.00
$112.00
$77.00
$77.00
$335.00
$113.00
$3,683.00
$903.00
$408.00
$2,159.00
$468.00
$1,526.00
$0.00
$638.00
$1,140.00
$73.00
$238.00
$1,397.00
Option No.
1685‐0315
1685‐0316
1685‐0317
1685‐0318
1685‐0319
1685‐0320
1685‐0321
1685‐0322
1685‐0323
1685‐0324
1685‐0325
1685‐0326
1685‐0327
1685‐0328
1685‐0329
1685‐0330
1685‐0331
1685‐0332
1685‐0333
1685‐0334
1685‐0335
1685‐0336
Description
Storage below rear bench seat. (1) hinged door on each side of the bench seat. The hinge shall be mounted on the forward edge of the opening each side.
Tag FAA data plate. Information shall include: nomenclature, manufacturer's make and model, manufacturer's serial number, vehicle curb weight, payload maximum, gross vehicle weight, fuel capacity and type, date of delivery, warranty duration, contract number, paint color and code.
The axle tag shall be modified to read Axle 1, 2 and 3 in place of the standard axle numbering convention. The tag shall be located on the driver's side cab door.
Rear lower engine cover mounted storage box. To be approx. 44" W x 8" H x 12" D. Includes (1) centered (front to rear) divider. Includes cargo net cover.
ABS Dash with controls for heating and air conditioning centered on the dash same as 2013 complaint vehicles.
Storage at rear engine cover w/ cargo net top. (4) sided storage approx. 44.5"W x 3" upper (13" lower) deep x 21" front to rear. ISX engines only. Storage area to match cab interior.
Divider below rear bench seat (PR). Requires side access doors. Location: (1) each side of front access door.
Storage at lower rear engine cover w/ cargo net top. Approx. 30"W x 8"H x 12" deep with a center divider (front to rear). Storage area to match cab interior.
Durawear interior panels ipo vinyl.
Storage at lower rear engine cover w/ lift up door and dividers for 3" binders. Approx. 24"W x 14"H x 12"D. Storage area to match cab interior.
Center control console. Locate in cab between driver and officer. Includes free area for customer supplied equipment to be added. Locate no equipment or switches in this console, using instead locations in overhead as specified.
Edge trim on top perimeter of map pockets.
ABS Dash package. Includes ABS center dash, officer side dash and "A" post covers. Lower kick panels are aluminum painted to match cab interior.
Fold down computer tray bolted to the map box on officer's side.
Map pockets aluminum plate painted to match cab interior (PR). Includes vinyl trim around top of opening and nylon strap with snap to retain contents. Locate pockets one each side on front wall of rear access map box between driver and officer.
Pac Trac panels vertical stacked on back wall of cab officer side outboard of seat(s).
Rear engine cover radio cabinet. 8"H x 44"W x 12"D (lower); ISC/ISL engines only. Includes lift‐up door with gas shock, locking thumb latches and louvers. Finish to match cab interior.
Interior access panel of cab roof antenna. Location: driver side forward, officer side forward and officer side rearward.
3/16" aluminum plate on top engine cover forward of access door approx. 32"W x 12.5"L. Finish to black Durabak and be spaced up approx 1‐1/4". Not available with cup holders.
VIN, Tire size, Paint Color and Vehicle Emissions tags to be metal engraved fastened in place with stainless steel hardware.
Rear engine cover swirl smooth plate (not clear coat) trim spaced 2" off cover. Includes lower horizontal surface and angle vertical surface between horizontal surfaces.
Storage below rear bench seat for two SCBA bottles (officer side). Driver side to be open storage w/ door.
PRICE
$648.00
$37.00
$79.00
$1,020.00
$0.00
$796.00
$373.00
$796.00
$0.00
$796.00
$1,727.00
$57.00
$0.00
$799.00
$440.00
$777.00
$727.00
$161.00
$294.00
$711.00
$589.00
$727.00
Option No.
Description
PRICE
1685‐0337
Riser rear seat(s) with transverse. For use with side access ALS and flip‐up ABTS seats. Transverse to be used for backboard storage.
Severe duty dash package with low profile center and officer side dash. Includes smooth plate alum center and officer side dash painted to match cab interior and lower dia plt kick panels.
Lower exterior cab steps to be equipped with Bustin Industries Type M stainless steel overlay in lieu of Gator Grip. Includes (6) 3/4" drain holes on the lower steps.
Battery charger cover NYPD.
Diamond plate power strip cover (ea).
Load management override switch cover
Storage at lower rear engine cover w/ cargo net top. Approx. 44"W x 8"H x 12" deep with (2) dividers (front to rear). Storage area to match cab interior.
Slide out command desk in cab. Location: Rear engine cover. Includes lower area below desk for storage with cargo net cover rear facing. Finish to match cab interior.
Cab interior tactical equipment storage module, painted black durabak.
$1,526.00
1685‐0338
1685‐0339
1685‐0340
1685‐0341
1685‐0342
1685‐0343
1685‐0344
1685‐0345
$1,163.00
$1,067.00
$281.00
$161.00
$0.00
$796.00
$2,965.00
$2,219.00
Storage cabinet mounted on the officer wheel well offset forward toward officer seat 15.5X24X21. Includes rear facing cargo netting.
Bolt‐in partition wall. Locate rear of driver seat approx. 21"W x 24"H.
Label and mechanically fastened tag package for NYPD units only, to include seating capacity tag in yellow with black lettering; (1) each side of overhead console. "Tower Up" label black with white lettering above tower ajar light. "Master Battery" tag yellow with black lettering and "Emergency Start" tag black with white lettering above cole hersee switches. "Do Not Grab To Adjust" label black with white lettering in lower mirror glass. O.A.H. 11' in 2" white vinyl on driver side of windshield on radius to not interfere with driver's view. "Extensions Only" tag in yellow with black lettering located at driver side strut tubes with yellow paint for tube ends. "Remove Struts Prior to Tiliting Cab" tag in yellow with black lettering located at cab tilt instructions.
$1,081.00
$236.00
$1,091.00
1685‐0352
1685‐0353
PAC TRAC panels vertical stacked with tool mounting grooves orientated horizontal each side backwall of outboard medical cabinets.
Diamond plate storage at rear engine cover w/ drop down rear door. Approx. 41"W x flush with upper engine cover high x sloped area of engine cover deep.
ABS Dash package for Quest cab. Includes driver side, center and officer side dash and lower kick panels.
ABS Dash package for Quest cab. Includes driver side, center and officer side dash. Lower kick panels are aluminum painted to match cab interior.
Divider below rear bench seat; adjustable. Requires side access doors.
1685‐0354
Label and mechanically fastened tag package for NYPD units only, to include seating capacity tag in yellow with black lettering; (1) each side of overhead console. "Tower Up" label black with white lettering above tower ajar light. "Master Battery" tag yellow with black lettering and "Emergency Start" tagl black with white lettering above cole hersee switches. "Do Not Grab To Adjust" label black with white lettering in lower mirror glass. O.A.H. 11' in 2" white vinyl on driver side of windshield on radius to not interfere with driver's view.
1685‐0346
1685‐0347
1685‐0348
1685‐0349
1685‐0350
1685‐0351
$0.00
$796.00
$0.00
$0.00
$373.00
$0.00
Option No.
1685‐0355
1685‐0356
1685‐0357
1685‐0358
1685‐0359
1685‐0360
1685‐0361
1685‐0362
1685‐0363
1685‐0364
1685‐0365
1685‐0366
1685‐0367
1685‐0368
1685‐0369
1685‐0370
1685‐0371
1685‐0372
1685‐0373
1685‐0374
1685‐0375
1685‐0376
1685‐0377
1685‐0378
1685‐0379
1685‐0380
1685‐0381
Description
Storage below rear bench seat. (1) cargo net (black) on each side of the bench seat to gain access to storage area. Includes snaps on top and bungee cord on bottom
Writing surface cab dash finished same as cab interior. Location: Mount at final inspection.
Rear cab interior wall overlay plates with Zolatone finish each side outboard of rear seating. Approx. 15"W x 32"H.
Storage at lower rear engine cover w/ lift‐up door (ISL only). Storage approx. 44.5"W x 15"H x 12"D. Storage area to match cab interior.
Electrical schematic aluminum pocket ceiling mounted in officer side wheel well communications cabinet.
Recessed storage area in front cab floor between driver and officer.
Interior access panel of cab roof antenna. Location: driver side forward, driver side rearward, officer side forward and officer side rearward.
Cab floor overlays. Front and rear cab floors to be overlayed with diamond plate painted with black Durabak. Single piece with no gaps around perimeter.
Locking seat riser door. Officer seat riser door is to include a Simplex model 9672C‐20‐260‐41 combination lock with satin chrome finish and black trim ring. Not available with air or electric seats.
Recessed access panel in MDT notch on officer side cab dash. Approx. 8" x 8".
Air ride seat pull down (S4) for RollTek air bag system.
Side Rollover Airbag (SRA) for RollTek air bag system.
Diamond plate tray rear engine cover. Approximately 43"W x 7.5"D x 2.5"H. Included strap over center of tray.
Pair of 36" handrails located inside driver and officer rear door on rear interior wall. Not available with outboard rear wall seats.
Severe duty dash package with low profile officer side dash. Includes smooth plate alum center and officer side dash and lower kick panels; all painted to match cab interior.
Bolt‐in partition wall. Locate under bench seat side to side at pass‐thru area of riser height compartments.
Overhead console flange re‐inforcement. Includes driver and officer side consoles.
Map pocket rear cab console aluminum plate to match console finish.
Transverse riser height area for use with exterior riser height compartments and fold down/flip up seats (if equipped).
Stack‐On model PS‐514‐12 gun safe. Location: centered on top of rear wall medical cabinet.
Center control console. Includes: VMUX panel mounting surface pitched at best angle to accommodate drivers position, area for NFPA siren, electrical, and in‐cab control switching (as applicable). Locate: In cab between driver and officer.
Rear engine cover shelves with cargo netting approx. 35" wide. Storage area to match cab interior. See sketch in file.
Fixed back wall mounted swirled overlay. Overlay to be spaced off wall approx. half inch. Location(s): center rear wall of cab full height above seat support channel x engine cover width.
Storage console. Locate in cab between driver and officer. Includes (3) 4" wide slots, (1) 6" wide slot and retaining strap.
Officer overhead panel painted FLNA4006 white.
Storage above rear wall medical cabinet w/ cargo net sides. Approx. 32"W x 22"H x 24" deep. Storage area to match cab interior.
1/8" aluminum plate on top engine cover forward of access door approx. 32"W x 12.5"L. with 1" lips around perimeter. Finish to match cab interior and be spaced up approx 1". Not available with cup holders.
PRICE
$648.00
$221.00
$306.00
$796.00
$199.00
$674.00
$161.00
$1,323.00
$387.00
$221.00
$1,025.00
$663.00
$427.00
$429.00
$1,222.00
$236.00
$112.00
$111.00
$414.00
$333.00
$2,152.00
$828.00
$282.00
$1,727.00
$201.00
$796.00
$464.00
Option No.
Description
PRICE
1685‐0382
$1,091.00
1685‐0386
1685‐0387
1685‐0389
PAC TRAC panels vertical stacked with tool mounting grooves orientated horizontal each side backwall of outboard of fold down seats.
Upper vista wedge on driver side wheel well medical cabinet. Includes rear facing cutout 9.5H x 12.5W centered approx 1.25" up from bottom with cargo netting. Wedge to match cab interior.
Interior access panel of cab roof antenna. Location: driver side forward and officer side forward.
Fixed back wall mounted swirled overlay. Overlay to be spaced off wall approx. 0.5". Location(s): driver side rear wall of cab outboard of rear wall seats full height above seat support channel.
Storage at upper rear engine cover between 3x3s w/ cargo net top. Approx. 34"W x 12.5"H x 12.5" D. Includes center divider (front to rear) and (2) side to side dividers in each storage area for a total of (6) slots.
LINE‐X package: Cab floor overlays shall be coated with LINE‐X.
Cup holders; severe duty dash. (1) metal to match cab interior driver forward engine cover, (1) polyurethane on officer dash.
1685‐0390
1685‐0391
Storage at rear engine cover w/ drop down rear door. (3) sided storage approx. 44.5"W x flush with upper engine cover (access door) high x approx. 22"D(upper)12"D(lower). Storage area to match cab interior. Door to be provided with cable hold open on each side.
Storage at rear engine cover w/ lift‐up door. Storage approx. 23"W x 13"H x 10"D. Storage area to match cab interior.
1685‐0383
1685‐0384
1685‐0385
1685‐0392
1685‐0393
1685‐0395
1685‐0396
1685‐0397
1685‐0398
1685‐0399
1685‐0400
1685‐0401
1685‐0402
1685‐0403
1685‐0404
Desk, command. A fixed command desk shall be provided in the cab. Includes: top tray designed large as possible with a 1 inch deep recess on top, an access provision to engine servicing access cover 'if applicable', rear outboard mitered corners for added clearance, cushioned arm rest & cup holders each side on top to accommodate rear facing seats over wheel well, (2) Interior cubbies at rear of engine cover upper and lower area with D‐handle drop down style hinged access doors to interior storage area. The upper and lower interior area shall be divided by an integral shelf. Finish: Shall be consistent with the cab interior and the upper tray shall have a swirled finish. Location: Over rear engine cover extending approx 36 inches aft of the 3x3 vertical support tubes.
Control lanyard type driver side only for air horns.
Panel, utility. A aluminmu panel shall be bolted to the rear facing surface of the 3x3 vertical post inside the cab above the engine cover. Panel shall be 16 inches tall. Finish: shall be consistant with the cab interior.
KNOX‐BOX KeySecure model 2642. Includes E‐ONE installed battery hot 12v power supply. Location: officer side of engine cover. Requires dept to purchase software package from KNOX‐BOX (if they do not already have it).
Manual cab tilt pump handle located adjacent to pump with cable tether.
Upper barrier cab door steps with NO notch and flat door.
Front engine cover trim 1/8" sanded smooth plate spaced 1/2" off cover. Full cover over angled sides and foward of access door.
Pac Trac panels vertical stacked on back wall of cab driver side outboard of seat(s).
LINE‐X package: Cab engine cover overlay trim shall be coated with LINE‐X.
Storage at rear engine cover w/ cargo net rear opening. Storage approx. 44.5"W x flush with upper engine cover high x sloped area of engine cover deep. Storage area to match cab interior.
Cup holders; severe duty dash for use in Typhoon and CII with severe duty engine cover only. Location: [#LOC]. Holders to match cab interior.
Cab steps and bolt‐on steps (if applicable) to be equipped with Bustin Industries Type M stainless steel overlay in lieu of Gator Grip.
$544.00
$161.00
$282.00
$765.00
$535.00
$246.00
$796.00
$757.00
$4,029.00
$186.00
$306.00
$1,295.00
$57.00
$0.00
$613.00
$777.00
$535.00
$796.00
$246.00
$1,804.00
Option No.
1685‐0405
1685‐0406
1685‐0407
1685‐0408
1685‐0409
1685‐0410
1685‐0411
1685‐0412
1685‐0413
1685‐0414
1685‐0415
1685‐0416
1685‐0417
1685‐0418
1685‐0419
1685‐0420
1685‐0421
1685‐0422
1685‐0423
1685‐0424
1685‐0425
Description
Chrome grab handle (PR). Locate (1) each side vertically mounted on rear facing seat riser(s) inboard.
Center control console. Includes: area for NFPA siren, electrical, and in‐cab control switching (as applicable). Console to be as large as possible. See photos on file with sales. Locate: In cab between driver and officer.
Inclinometer, phosphorescent illumination with 20‐0‐20 side slope indicator. LED light to be mounted above inclinometer.
Tag for overall height, length, width to be located on dash to driver side of steering wheel in location visible from the driver's seat.
Storage cabinet center rear crew area. Box to be installed from behind upper rear engine cover to rear wall with open sides and (1) fixed shelf at lower rear engine cover level. Sides will be provided with cargo net covers. Handrails provided on each side top of cabinet. Cabinet to match cab interior.
Drug box with PharmGuard climate control system. Construction is of aluminum and an integral design utilizing the cab rear wall medial cabinet. Drug box interior area shall be lined with Dynamat insulation. Design shall include thumb style lever latches with a single Simplex combination lock centered between the thumb style latches and a front drop down hinged access door. Finish to match cab rear wall mdeical cabinet interior. Locate: Inside cab rear wall medical cabinet at floor level. PharmGuard shall be located on the officer side of the box and protrude thru the side of the rear cab wall mounted medical cabinet as required to accommodate venting and control access.
Storage cabinet center rear crew area. Box to be installed from behind upper rear engine cover to rear wall with open sides and (1) fixed shelf at lower rear engine cover level. Sides will be provided with cargo net covers. Cabinet to match cab interior.
Cab interior gray with black driver dash only. Does not include engine cover or seat color.
Rear engine cover diamond plate trim. Each area to be individual plate spaced 1/2" off of cover. Total of (5) plates.
Storage at rear engine cover w/ lift‐up door. Storage approx. 42.5"W (for use with ABTS seats) x flush with upper engine cover high x sloped area of engine cover deep. Storage area to match cab interior.
Cab interior wheel well risers angled and pushed as far forward as possible to match lower rear engine cover.
KNOX‐BOX MedVault 2 model 5520H3S2‐4. Includes E‐ONE installed wiring to battery hot. Location: above officer side wheel well medical cabinet facing rear. Requires dept to purchase software package from KNOX‐BOX (if they do not already have it).
Radio cabinet above driver side wheel well medical cabinet. 6"H x 19"W x 28"D. Includes removable top with locking thumb latches and louvers on side walls. Finish to match cab interior.
Louvers, additional for cab mounted center console. Locate louvers on lower area of sides for extra ventilation.
Reduced profile rear engine cover for increased legroom. Not available with rear engine cover options.
Officer seat riser storage opening to be provided with cargo netting in place of standard door.
3/16" Aluminum plate on top engine cover forward of access door approx. 22"W x 11"D offset to officer side. Finish to match cab interior and be spaced up approx 1/2". Not available with cup holders.
Severe duty overhead console. Includes front full width overhead, air conditioning plenum and rear facing blower. Overhead to match cab interior.
Driver side severe duty dash. Includes driver side aluminum upper dash to match cab interior with ABS gauge cluster. CIIX and TyphoonX cabs only.
Rear cab interior wall overlay plates with Zolatone finish each side outboard of rear seating. Approx. 24"W x 36"H.
Panel, blank and housing cutout for severe duty dash upper tier. Includes: dash housing to be cutout behind panel overlay area. Color: Black.
PRICE
$121.00
$2,152.00
$197.00
$0.00
$3,065.00
$5,423.00
$2,910.00
$258.00
$524.00
$796.00
$1,555.00
$2,820.00
$727.00
$369.00
$124.00
$114.00
$323.00
$2,514.00
$375.00
$306.00
$360.00
Option No.
1685‐0426
1685‐0427
1685‐0428
1685‐0429
1685‐0430
1685‐0431
1685‐0432
1685‐0433
1685‐0434
1685‐0435
1685‐0436
1685‐0437
1685‐0438
1685‐0439
1685‐0440
1685‐0441
1685‐0442
1685‐0443
1685‐0444
1685‐0445
1685‐0446
Description
Severe duty dash package with low profile center and officer side dash. Includes smooth plate alum center, officer side dash and lower kick panels; all painted to match cab interior.
(3) severe duty dash upper tier blank panels (as applicable with other options in upper tier; ship additional panel(s) loose). Includes: dash housing to be cutout behind panel overlay areas. Color: Black.
Rear engine cover shelves with cargo netting approx 35" wide. Storage area to match cab interior. Includes 1/2" lip around top. See photos on file with sales.
PRICE
Severe duty overhead console. Includes driver, center and officer overhead and defrost only plenum. Overhead to match cab interior.
Heavy Duty interior panels includes: all ceilings panels, back wall and side walls to be .125" aluminum smooth plate painted to match cab interior. Requires additional insulation for cab interior.
Storage below rear facing seat riser (PR).
Map pocket(s) aluminum plate painted to match cab interior. Includes vinyl trim around top of opening and nylon strap with snap to retain contents. Locate pocket(s) on front wall of rear access map box/medical cabinet between driver and officer.
Smooth plate cover for air compressor. Includes louvers for ventilation. Cover to match cab interior.
Storage cabinet center rear crew area. Box to be approx. 26.5" tall installed from behind upper rear engine cover to rear wall with open sides and (1) fixed shelf at lower rear engine cover level. Sides will be provided with cargo net covers. Handrails provided on each side top of cabinet. Cabinet to match cab interior.
Cup holder (EA). Polyurethane construction for use in Typhoon and CII with severe duty engine cover only. Location: tillerman cab.
3/16" Aluminum plate with sanded finish on top engine cover forward of access door. To have peg board design and be spaced up approx 1/2".
Main control console. Locate in cab centered between driver and officer. Includes NFPA in‐cab controls/switching.
Divider(s) below rear bench seat to protect back of heaters from pass‐thru (if equipped).
Diamond plate cover for PharmGuard climate control system. Includes ventilation as requrired.
Storage below rear bench seat. Cargo netting cover on the front of the rear bench seat.
Engine access door to open approx. 90 degrees.
Driver side cab interior wheel well riser positioned 2" forward from std.
LINE‐X package: Lower front cab dash kick panels shall be coated with LINE‐X. Requires severe duty dash.
Drug box with PharmGuard climate control system. Construction is of aluminum and an integral design utilizing the cab rear wall medial cabinet. Drug box interior area shall be lined with Dynamat insulation. Design shall include thumb style lever latches with a single Simplex combination lock centered between the thumb style latches and a front drop down hinged access door. Finish to match cab rear wall mdeical cabinet interior. Locate: Inside cab rear wall medical cabinet below roll‐up door drum. PharmGuard shall be located on the driver side of the box and protrude thru the side of the rear cab wall mounted medical cabinet as required to accommodate venting and control access.
Officer side cab dash access door. Includes louvers and push button latch.
Severe duty overhead console. Includes driver, center and officer overhead ahead of air conditioning plenum. Overhead to match cab interior.
$1,965.00
$1,163.00
$397.00
$1,007.00
$1,708.00
$443.00
$440.00
$238.00
$3,065.00
$78.00
$323.00
$0.00
$373.00
$238.00
$593.00
$0.00
$468.00
$535.00
$5,423.00
$268.00
$1,415.00
PRICE
1685‐0462
Description
Drug box with PharmGuard climate control system. Construction is of aluminum and an integral design utilizing the cab rear wall medial cabinet. Drug box interior area shall be lined with Dynamat insulation. Design shall include thumb style lever latches with a single Simplex combination lock centered between the thumb style latches and a front drop down hinged access door. Finish to match cab rear wall mdeical cabinet interior. Locate: Inside cab rear wall medical cabinet at floor level. PharmGuard shall be located on the driver side of the box and protrude thru the side of the rear cab wall mounted medical cabinet as required to accommodate venting and control access.
Radio cabinet above officer side wheel well medical cabinet. 6"H x 19"W x 28"D. Includes removable top with locking thumb latches and louvers on side walls. Finish to match cab interior.
3/16" aluminum plate on top engine cover forward of access door approx. 32"W x 12.5"L. Finish to match cab interior and be spaced up approx 1/2". Not available with cup holders.
Center control console painted black Zolatone. Locate in cab between driver and officer. Includes area for NFPA siren, electrical, and in‐
cab controls (as applicable) switching.
Overlay, cab interior rear wall. Overlay to span area from bottom of overhead cabinets to top of rear wall raceway. Material: 3/16 aluminum smooth plate.
Storage below rear bench seat. (1) hinged door on officer side of the bench seat.
Line‐X. Rear cab interior wall overlay with Line‐X finish.
Line‐X. Shelf on cab cab interior rear wall shall have a Line‐X finish.
Storage above driver wheel well medical cabinet w/ rear facing opening and cargo netting. Approx. 22"W x 16"H x 28" deep. Storage area to match cab interior.
Storage above officer wheel well medical cabinet w/ rear facing opening and cargo netting. Approx. 22"W x 16"H x 28" deep. Storage area to match cab interior.
Storage below rear bench seat. (1) cargo net (black) on front of the bench seat to gain access to storage area.
Delete power steering access door on engine cover. ISX engines only. Requires signed NFPA exception.
Storage at upper rear engine cover w/ cargo net rear opening. Storage approx. 44.5"W x 12"H x 22"D. Includes 3/4" lip around perimeter of top. Storage area to match cab interior.
Storage box approximately 11" wide x 10" high x 26" deep made from 1/8" diamond plate aluminum, centered on to rear cab floor. The box shall cradle (1) 2.5 gallon water fire extinguisher. Includes hinged door on each side with push button latches to provide easy access to the extinguisher in its stowed position within the box.
Cup holder / tray for engine cover painted to match cab interior. Approx 16" wide x 11" long with tapered front corners and cup holders at each front outer corner. For use in Typhoon and CII with severe duty engine cover.
Cup holder / tray for engine cover painted to match cab interior. Approx 14" wide x 10" long with tapered front corners and cup holders at each rear corner. For use in Typhoon and CII with severe duty engine cover. Locate on engine cover access door. Not available with map box.
1700‐0001
1700‐0002
1700‐0003
Alternators Leece Neville dual 270 amp. 480 amp NFPA/540 amp SAE rating. Available only on ISX12 and Detroit EGR Series 60 engines.
Alternator Niehoff 250amp. (250 amp SAE/240 NFPA rating). Not available on Cummins ISC or Detroit Diesel engines.
Alternator Leece Neville 270 amp SAE, 240 amp NFPA rating.
$4,055.00
$2,611.00
$2,131.00
Option No.
1685‐0447
1685‐0448
1685‐0449
1685‐0450
1685‐0451
1685‐0452
1685‐0453
1685‐0454
1685‐0455
1685‐0456
1685‐0457
1685‐0458
1685‐0459
1685‐0460
1685‐0461
$5,423.00
$727.00
$294.00
$756.00
$305.00
$324.00
$1,006.00
$705.00
$796.00
$796.00
$468.00
$250.00
$896.00
$824.00
$434.00
$434.00
Option No.
1700‐0004
1700‐0005
1700‐0006
1700‐0007
1700‐0008
1700‐0009
1700‐0010
1700‐0012
1700‐0013
1700‐0014
1700‐0015
1700‐0016
1700‐0017
1700‐0018
1700‐0019
1700‐0020
1700‐0021
1700‐0022
1700‐0023
1700‐0024
1750‐0000
1750‐0001
1750‐0002
1750‐0004
1750‐0006
1750‐0008
1750‐0009
1750‐0010
1750‐0011
1750‐0012
1750‐0013
Description
Alternator Niehoff 290 amp (290 amp SAE/265 NFPA rating). Not available on Cummins ISC, ISL or Detroit Diesel engines.
Alternator Leece Neville 320 amp. 320 amp SAE/275 amp NFPA.
Alternator Niehoff 400amp (400 Amp SAE/385 NFPA rating). Cyclone II w/Cummins ISM. Not available on Detroit Diesel Engines Recycle requires Eng. Review.
Altenator 24 VDC 150 amp Leece Neville with regulator.
PRICE
$3,977.00
$3,446.00
Alternator Leece Neville dual 320 amp. 560 amp NFPA/540 amp SAE rating. Available only on ISX12 and Detroit EGR Series 60 engines.
Alternator Niehoff 300 amp (300 amp SAE/270 NFPA rating). Available only on ISX12 and Detroit EGR Series 60 engines.
Noise filter for Leece Neville alternator.
Alternator Niehoff 430 amp (430 Amp SAE/380 NFPA rating). Available on Cummins ISX12 only.
Alternator / battery / battery charger package. Includes 270AMP Leece Neville alternator, (4) 12 volt batteries, E‐ONE battery charger with receptacle (located outside driver door area), and jumper studs. Custom ES.
Alternator / battery / battery charger package. Includes 320AMP Leece Neville alternator, (4) 12 volt batteries, E‐ONE battery charger with receptacle (located outside driver door area), and jumper studs. Custom ES.
Alternator / battery / battery charger package. Includes 320AMP Leece Neville alternator, (4) Group 31 batteries, E‐ONE battery charger with receptacle (located outside driver door area), and jumper studs. Custom ES with DEF tank below cab
Alternator Niehoff 350 amp (350 amp SAE/320 NFPA rating). Available on Cummins ISM.
Noise filter for Neihoff alternator.
** OBS ** (Use 1700‐0024) Alternator Delco Remy 300 amp SAE, 261 amp NFPA.
Alternator Niehoff 360 amp (360 amp SAE/320 NFPA rating). Available only on ISX12 and ISX15.
Alternator Niehoff (400 Amp SAE/385 NFPA rating). Cyclone II w/Cummins ISM. Not available on Detroit Diesel Engines Recycle requires Eng. Review.
Alternator Niehoff 360 amp (360 amp SAE/320 NFPA rating). Available only on ISL.
Alternator Delco‐Remy 430 amp (430 Amp SAE/363 NFPA rating). Available on Cummins ISX only.
Alternator 320 amp for Freightliner ‐ in place of 275 amp.
Alternator Delco Remy 320 amp. (320 Amp SAE/253 NFPA rating)
Ammeter gauge in cab 0‐300 amps.
Dome lights clear large one for each cab door.
Dome lights red large one driver side one officer side
Dome lights red large one driver side one officer side rear of cab
Map light flexible arm. Located [#LOC].
Radio AM/FM cassette with weather band located [#LOC]
Radio AM/FM CD with weather band located [#LOC].
Radio speakers additional pair. Locate each side rear cab ceiling.
Speedometer officer's side overhead.
Swivel reading lamps (PR) overhead between driver and officer. Lights to be individually switched.
Turn signal Whelen 600 LED amber arrow pair located [#LOC].
$5,575.00
$3,449.00
$226.00
$4,757.00
$6,031.00
$1,288.00
$0.00
$515.00
$515.00
$3,977.00
$229.00
$3,378.00
$3,449.00
$6,031.00
$3,449.00
$3,585.00
$347.00
$3,378.00
$338.00
$151.00
$151.00
$151.00
$211.00
$555.00
$849.00
$287.00
$327.00
$115.00
$675.00
Option No.
1750‐0015
1750‐0016
1750‐0019
1750‐0021
1750‐0022
1750‐0024
1750‐0025
1750‐0026
1750‐0027
1750‐0029
1750‐0030
1750‐0031
1750‐0032
1750‐0033
1750‐0034
1750‐0035
1750‐0038
1750‐0040
1750‐0042
1750‐0043
1750‐0045
1750‐0046
1750‐0047
1750‐0048
1750‐0049
1750‐0050
1750‐0052
1750‐0053
1750‐0054
1750‐0058
1750‐0059
1750‐0060
1750‐0061
1750‐0062
1750‐0063
Description
Windshield fans 8" pair. Location: [#LOC].
Pump hourmeter in cab.
Battery charger Super Smart 110 volt, 20 amp.
Battery charger Kussmaul model 1200, 40 amp.
Battery charger Kussmaul 40 amp model 1200 with air compressor.
Auto‐Eject receptacle inlet 20 amp located [#LOC] with a [#COL] cover.
Super Auto‐Eject receptacle inlet 30 amp 120 volt located [#LOC] and with a [#COL] cover.
Clamshell controller mounted on officer's side of engine cover for the air horns.
Control push‐button switch officer dash for Q2B siren.
Switch horn button two position DOT/air horn.
Switch horn button two position DOT/electronic siren.
Switch horn button two position DOT/Q2B.
Switch horn button three position DOT/air horn/electronic siren.
Switch horn button three position DOT/air horn/Q2B.
Switch, additional 12 volt/15 amp. Location and function: [#LOC].
Cornering light relay circuits for lights on sides of cab and / or bumper. Includes (2) relays. Requires scene light option. Interlocked with park brake.
Cab Dome Lights Additional (PR) Color to be: [#COL]
Battery charger Super Smart 220 volt 50 Hz, 20 amp.
Horn button selector switch, 3‐position DOT/ES/Q2B.
12V power distribution module. Includes (6) battery hot and (6) switched hot circuits. 100 amps max (IATS).
Compass 12 Volt Illuminated
Cab Headlights. Position: [#LOC].
The chassis shall be pre‐wired for installation of tire chains.
Round clear incandescent light mounted in the [#LOC] door.
Round red incandescent light mounted in the [#LOC] door.
Round amber incandescent light mounted in the [#LOC] door.
Round clear LED light mounted in the [#LOC] door.
Round red LED light mounted in the [#LOC] door.
Round amber LED light mounted in the [#LOC] door.
Remote Switch 24 Volt 110‐240 Volt Devices
Receptacle inlet 20 amp with a [#COL] cover. Location: [#LOC].
Auto transfer switch 120 volt. Includes 8 place breaker box. Allows interior receptacles to be powered by either shore power or generator.
Control push‐button switch officer dash for air horns.
Control push‐button switch officer dash for siren.
Clamshell controller mounted on officer's side of engine cover for Q2B.
PRICE
$394.00
$143.00
$440.00
$739.00
$2,491.00
$601.00
$878.00
$131.00
$100.00
$105.00
$105.00
$105.00
$212.00
$212.00
$212.00
$432.00
$283.00
$440.00
$212.00
$327.00
$235.00
$0.00
$565.00
$38.00
$38.00
$38.00
$171.00
$65.00
$65.00
$464.00
$304.00
$798.00
$100.00
$100.00
$131.00
Option No.
1750‐0064
1750‐0065
1750‐0066
1750‐0067
1750‐0068
1750‐0069
1750‐0070
1750‐0071
1750‐0072
1750‐0073
1750‐0074
1750‐0075
1750‐0076
1750‐0077
1750‐0078
1750‐0079
1750‐0080
1750‐0081
1750‐0082
1750‐0083
1750‐0084
1750‐0088
1750‐0091
1750‐0092
1750‐0093
1750‐0094
1750‐0095
1750‐0096
1750‐0097
1750‐0098
1750‐0100
1750‐0101
1750‐0102
Description
Clamshell controller mounted on on officer's side of engine cover for electronic siren.
Turn signal Whelen 600 halogen amber pair located [#LOC].
Halogen front turn signal amber (PR). Locate: [#LOC].
Additional 4" red LED dome lights (PR) for driver and officer.
Additional 4" red incandescent dome lights (PR) for rear of cab.
Additional 4" red incandescent dome lights (PR) for driver and officer.
Additional 4" red LED dome lights (PR) for rear of cab.
Mount customer supplied antenna on cab roof. Location: [#LOC].
12 VDC (or 24VDC) electrical outlet in the cab wired battery hot. Location: [#LOC].
Antenna base Tessco P/N 90942 (NMO Motorola Style ‐ also called MATM style) on cab roof. Location: [#LOC].
Interlock to position front intake for cab tilting.
English dominant main cab gauge cluster.
Metric dominant main cab gauge cluster.
Turn signal Code 3 model 65 LED amber with arrow insert (PR). Location: [#LOC].
Light Whelen model PSR00FRR LED (4) red. Horizontal mounted flashing strip light on each of the inside lower cab door panels. Wire through door switch.
Fuel gauge for officer.
Conduit flexible 1.5" for radio installation center of dash to compartment under officer's seat.
Conduit flexible 1.5" for radio installation compartment under officer's seat to pump panel.
12V power distribution module. Includes (6) battery hot and (6) switched hot circuits. 100 amps max (IATS). Location: [#LOC].
Turn signal Federal Signal QuadraFlare QL64Z‐ARROW LED amber pair located [#LOC].
Receptacle inlet 220 volt European "Schuko" style. Includes matching cord connector. Location: [#LOC]
Whelen 500 LED red door ajar light. Model 50R00FRR light with 5FLANGEC flange.
Battery Saver Kussmaul model 091‐195‐12 wired to battery charger receptacle.
Warning Lights shall be switched Off/Amber/All.
Warning lights shall be switched Off/Upper/All.
Battery charger / air compressor 220 volt Kussmaul Pump Plus HO.
Second DOT traffic horn
Bracket for Motorola Spectra Radio in the center overhead console offset to officer side. Dim: 7''W x 2''H, must be size of the opening after break.
LED Light in cab to Illuminate Pump Shifter and shall activate with the headlights.
Dome Lts Red/White Weldon with Euro style switches. Package includes two lights mounted in the front and two mounted in the rear of the cab. White light wired through master battery switch, door ajar and light assembly mounted switch. Red light through light assembly mounted switch.
Install ES‐Key Display on Driver's Side of Doghouse by Shifter
Install EQ2B Amplifier on Front face of Communication Box behind Driver's Seat
Rear flood light switch in cab to operate the rear deck lights.
PRICE
$131.00
$298.00
$288.00
$298.00
$279.00
$227.00
$298.00
$184.00
$64.00
$99.00
$291.00
$2,133.00
$2,258.00
$755.00
$829.00
$263.00
$317.00
$279.00
$327.00
$288.00
$433.00
$197.00
$730.00
$54.00
$54.00
$1,569.00
$141.00
$86.00
$53.00
$588.00
$0.00
$0.00
$0.00
Option No.
1750‐0103
1750‐0104
1750‐0105
1750‐0106
1750‐0107
1750‐0108
1750‐0109
1750‐0110
1750‐0111
1750‐0113
1750‐0114
1750‐0115
1750‐0116
1750‐0117
1750‐0118
1750‐0119
1750‐0120
1750‐0121
1750‐0122
1750‐0123
1750‐0124
1750‐0125
1750‐0126
1750‐0128
1750‐0129
1750‐0130
1750‐0131
1750‐0132
1750‐0133
1750‐0134
Description
Primary warning light switch to operate all warning lights and lightbar, except arrowstick traffic advisor and rear amber upper warning lights. Master warning light switch must be on as well.
Left alley lights to control driver's side white light on lightbar.
Right alley lights to control officer's side white light on lightbar.
One (2) position switch (Master) to initiate battery circuit ‐ Typhoon style Eaton switch with red guard.
One (2) position switch (Ignition) to initiate ignition circuit ‐ CII style Carling switch.
Seat belt detection system programmed to 2" red door ajar light and ES‐Key display. Also tied to a "different sounding alarm".
The following items are not programmed through Master Warning Light switch: Left and Right Alley light. Left, Right, and Rear Scene Light, Ground Light and Horn/Air.
Battery Charger Professional Mariner. Located outside driver side door area. The charger to be mounted behind driver's seat on front face of communication box, next to EQ2B amplifier.
Digital voltmeter in cab. Location: Driver side overhead console.
Dome Lts Red/White Incandescent. Package includes two lights mounted in the front of the cab. White light wire through door and light assembly mounted switch. Red light through light assembly mounted switch.
Cab Headlights in addition to front quad headlights
Master warning light switch to have a red cover (or bezel).
Warning Lights shall be switched Off/Amber/Emergency.
Auto eject receptacle inlet 15 amp 240 volt with a [#COL] cover. Location: [#LOC].
Flexible 2" conduit with connectors. Location: Officer cab dash to bottom of medical cabinet.
Flexible 2" conduit with connectors. Location: Center cab dash to rear bench seat riser.
Receptacle/auto‐eject shall be wired to [#LOC].
Ammeter gauge in cab 0‐400amp Cruz Pro digital.
Additional dome lts red/white 4" LED (PR) located one each side over enclosed TM pump panel. White light wired through door and light assembly mounted rocker switch. Red light through light assembly mounted rocker switch.
Auto eject receptacle inlet 15amp location or function [#LOC] and the color shall be [#COL].
Whelen 4'' round LED red door ajar light. Model 20R00FCR light with 2FLANGEC bezel.
Block heater receptacle 15 amp with a [#COL] cover. Location [#LOC].
Conduit flexible 1.5" for radio installation center of dash to area behind officer's seat.
Locate swivel lamps per photos on file from 131288 # 1‐I‐0804.
Door ajar alarm to be a chime versus an alarm.
Xantrex Truecharge 40+. Wire to autoeject receptacles.
Pyrometer gauge in cab.
Auto transfer switch for additional battery charge receptacle.
Conduit flexible 1.5" for radio installation center of dash to rear bench seat.
Conduit flexible 1.5" for radio installation rear bench seat to pump panel.
PRICE
$0.00
$0.00
$0.00
$0.00
$0.00
$640.00
$0.00
$1,171.00
$358.00
$295.00
$451.00
$41.00
$54.00
$549.00
$386.00
$335.00
$0.00
$505.00
$795.00
$546.00
$197.00
$304.00
$317.00
$0.00
$228.00
$1,787.00
$600.00
$483.00
$317.00
$485.00
1750‐0158
1750‐0159
Description
35 AMP inline fuse as hot lead for radio installation. Radio circuit with G30060‐1CR in‐line fuse 35 amp. Fuse wired to ignition side to power the radio head. To be labeled and identified as ''HOT''. In‐line fuse to be clearly labeled. Wiring located behind a face plate in the center overhead also provide ground wire and label wires. Label ground ''Chassis Ground''. Run speaker wires from center overhead to above the medical cabinets on each side leave 36" of coiled wire.
Battery charger Super Smart 220 volt 60 Hz, 20 amp.
Work lights to be programmed "on" when park brake is set and switched in overhead console.
Provide 30 amp radio circuit with 6' of wire (PR)
Mount customer supplied antenna(s) on cab roof. Location(s): (1) each side of A/C condensor and (1) GPS antenna located top of vista officer side front corner. Includes coaxial cable terminating in the rear bench seat riser.
Bullard T4 hand held Thermal imaging camera with charger. Mount Location.[#LOC]
Kussmual Auto‐Eject 20 on each side of charger with a Red cover. Auto‐eject on each side of cab to alow plug in on either side for battery charger with transfer switch in cab.
Q2B brake switch to have a red cover (or bezel).
Relocate the battery charger and (if applicable) air compressor to below the rear wall bench seat or rear center wall medical cabinet (if equipped).
Hand held flashlight, orange Streamlight Survivor Division 2 right angle flashlight with 12 VDC fast charger. [#LOC].
Turn signal Whelen 700 LED Chevron amber (PR). Locate [#LOC].
Control push‐button switch on officer's dash for Q2B siren brake.
Block heater receptacle 20 amp Auto‐Eject with a [#COL] cover. Location [#LOC].
Receptacle inlet 15amp with a [#COL] cover. Location: [#LOC]
Federal Signal model 462121 Renegade red strobe light for compartment warning light under over head console.
Cab keyless entry touch pad(s) to lock/unlock all cab doors and cab/body electric locking roll‐up door(s).
Secondary keyless entry touch pad on officer side of cab. Pad to include any and all functions provided by the driver side pad.
Special EQ2B power amplifier location. Amp to be located [#LOC].
Special battery charger location. Charger to be located [#LOC].
Dome Lts Red/White LED. Package includes two lights mounted in the front and two mounted in the rear of the cab. White light wired through door and light assembly switch. Red light through light assembly switch.
3 Position Q2B momentary switch (activate/off/brake). Loc: [#LOC].
1750‐0160
1750‐0161
1750‐0162
1750‐0163
1750‐0164
Dome Lts Red/White Incandescent. Package includes two lights mounted in the front and two mounted in the rear of the cab. Front cab lights: White light wired through door and light assembly mounted switch. Red light through light assembly mounted switch. Rear cab lights: White light wired through door and switch on side cab interior wall. Red light through switch on side cab interior wall. Rear dome switches to be located between side window and door opening and control light on respective side of cab.
Air compressor, Kussmaul model 091‐9B‐1, 120V.
Battery charger Kussmaul model 091‐35/10, 35 amp battery charger / 10 amp battery saver.
Speedometer officer's side switch panel.
Fuel gauge for officer. Location: officer switch panel.
Option No.
1750‐0135
1750‐0136
1750‐0138
1750‐0139
1750‐0140
1750‐0141
1750‐0142
1750‐0144
1750‐0145
1750‐0147
1750‐0148
1750‐0149
1750‐0150
1750‐0151
1750‐0153
1750‐0154
1750‐0155
1750‐0156
1750‐0157
PRICE
$593.00
$440.00
$131.00
$124.00
$184.00
$21,770.00
$1,574.00
$41.00
$582.00
$282.00
$707.00
$100.00
$601.00
$304.00
$279.00
$609.00
$495.00
$292.00
$292.00
$849.00
$212.00
$1,006.00
$1,028.00
$863.00
$327.00
$263.00
Option No.
1750‐0165
1750‐0166
1750‐0167
1750‐0168
1750‐0169
1750‐0171
1750‐0172
1750‐0173
1750‐0174
1750‐0176
1750‐0177
1750‐0178
1750‐0179
1750‐0180
1750‐0181
1750‐0182
1750‐0183
1750‐0184
1750‐0185
1750‐0186
1750‐0187
1750‐0188
1750‐0189
1750‐0190
1750‐0191
1750‐0192
Description
Conduit flexible 1.5" for radio installation center of dash to compartment under driver's seat.
ATC override switch.
Block heater to be wired to battery charger receptacle with a lighted on/off switch behind driver seat.
Dome Lts Red/White 4" incandescent (5). Lights to be located two front and three rear. White light wired through door and light assembly mounted rocker switch. Red light through light assembly mounted rocker switch.
Radio speakers (3). Locate officer ceiling and each side rear cab ceiling. Wiring to terminate in officer side overhead console for customer supplied radio(s).
Clamshell controller mounted on on driver's side of engine cover for Q2B.
Special battery charger and air compressor location. Charger and air compressor to be located [#LOC].
Rocker switch cover (or bezel) to be red. Location: [#LOC].
Battery Charger Professional Mariner. Located outside driver side door area. The charger to be mounted under rear bench seat riser (centered) .
Light Whelen model 70RA6FCR Super LED (4) split red/amber with chrome flanges. Horizontally mounted flashing lights on each of the interior cab door panels outboard mounted. Wire through door switch.
Receptacle inlet 30amp twist lock with a [#COL] cover. Location: [#LOC].
Windshield fan 8". Location: rear facing mounted on driver side 3x3 post.
Dome light red/white Incandescent for tiller cab. White light wire through door and light assembly switch. Red light through light assembly switch.
PRICE
$317.00
$212.00
$211.00
Dome light red/white LED for tiller cab. White light wire through door and light assembly switch. Red light through light assembly switch.
Dome light red/white 4" incandescent for tiller cab. White light wired thru door and light assembly mounted rocker switch. Red light thru light assembly mounted rocker switch.
Dome light red/white 4" LED for tiller cab. White light wired through door and light assembly mounted rocker switch. Red light through light assembly mounted rocker switch.
Wire Oil Pan Heater Provided by Commercial ChassisThrough Battery Charger Receptacle.
Auto eject receptacle inlet 15amp / 240V located [#LOC] with a [#COL] cover.
Vernier engine throttle in cab for use with jet dump operations. Locate in driver side overhead console or Lower Dash. Includes selector sw also in overhead console or Lower Dash.
Dome Lts Red/White Incandescent additional. White light wire through door and light assembly mounted switch. Red light through light assembly mounted switch. Location: Centered rear of cab.
Auto drain, Kussmaul model 091‐9‐089 120V. For use with air compressor 091‐9B‐1 only.
DPF regeneration override switch.
Gauge ambient temperature with digital display. Locate display on officer side switch panel.
Dome Lts Red/White LED. Package includes two lights mounted in the front of the cab. White light wire through door and light assembly mounted switch. Red light through light assembly mounted switch.
Cab quad headlights below front bumper in addition to standard headlights.
Aerial engagement switch in cab to have a red cover (or bezel).
$214.00
$766.00
$493.00
$131.00
$292.00
$41.00
$1,464.00
$1,692.00
$582.00
$199.00
$150.00
$155.00
$399.00
$209.00
$598.00
$954.00
$151.00
$218.00
$212.00
$870.00
$426.00
$536.00
$41.00
Option No.
1750‐0193
1750‐0194
1750‐0195
1750‐0196
1750‐0197
1750‐0198
1750‐0199
1750‐0200
1750‐0201
1750‐0202
1750‐0203
1750‐0204
1750‐0205
1750‐0206
1750‐0207
1750‐0208
1750‐0209
1750‐0210
1750‐0212
1750‐0213
1750‐0214
1750‐0215
1750‐0216
1750‐0217
1750‐0218
1750‐0219
1750‐0221
Description
Oil level sensor light in cab to indicate drop in hydraulic reservoir oil level. Interlock w/parking brake, tag to read "Power Steering System Failure, Stop Vehicle".
Dome Lts Red/White LED additional (PR). White light wire through door and light assembly switch. Red light through light assembly switch. Location: Rear crew area.
Cab dome lts red/white (2 red/white, 2 white) 4" incandescent. White light wired thru door and light assembly mounted rocker switch. Red light thru light assembly mounted rocker switch. Red/white located in front of cab, white located at rear cab doors.
Battery charger Newmar model PT‐80, 80amp.
Clamshell controller mounted on driver's side of engine cover for the air horns.
Battery charger to be located [#LOC].
Air compressor to be located [#LOC].
Whelen model 1510R red strobe hazard warning light. Locate in cab under over head console.
Shore line receptacle and air inlet. Driver side cab step area.
Kussmaul battery charger with air compressor and air inlet. The battery charger receptacle and air inlet to include auto‐eject. Locate to driver side below the driver door.
Special location for battery charger indicator. Location: [#LOC].
Battery charger with indicator, inlet receptacle and air inlet with mounting plate. Locate to driver side of cab below driver door opening.
Handheld flashlight, orange Streamlight Vulcan flashlight with vehicle mount system. Location: [#LOC].
Clamshell controller mounted on officer's side cab dash for Q2B and air horns.
Lovered cover for battery charger or air compressor (EA). Finish to match cab interior.
Light Whelen model PSA00FAR LED (4) amber. Horizontal mounted flashing strip light on each of the interior lower cab door panels outboard. Wire through door switch.
Clamshell controller mounted on on officer's side of engine cover (knee height) for Q2B.
Vernier engine throttle in cab for pump&roll operations. Locate in console or Lower Dash. Includes selector sw also in center console or Lower Dash.
Battery charger and air compressor package 240 VAC/ 50 HZ.
Auto eject receptacle inlet 20 amp 240 volt, 24V inner coils with a [#COL] cover. Location: [#LOC]
Mount customer supplied GPS antenna on cab roof. Location: [#LOC].
Turn signal Whelen M6 LED arrow amber pair located [#LOC].
Mount customer supplied MAR antennas (5) on cab roof. Location: (1) approx 12" ahead of vista 18" left of cab center, (1) approx 12" ahead of vista 18" right of cab center (forward antennas will be 36" apart), (1) approx 18" rearward from front edge of vista centered left to right, (1) approx 18" rearward from front edge of vista 18" left of center and (1) approx 18" rearward from front edge of vista 18" right of center. Route all cables to below rear wall bench seat.
Conduit flexible .375" for radio installation driver dash to center overhead console.
Gauge engine oil temp in driver overhead console.
Keyed battery/ignition switch.
Xenon HID cab headlights. CIIX and TyphoonX only.
PRICE
$148.00
$426.00
$612.00
$3,692.00
$131.00
$0.00
$0.00
$284.00
$0.00
$991.00
$117.00
$0.00
$270.00
$131.00
$203.00
$829.00
$131.00
$954.00
$1,505.00
$331.00
$184.00
$682.00
$734.00
$317.00
$520.00
$141.00
$1,870.00
Option No.
1750‐0222
1750‐0223
1750‐0224
1750‐0225
1750‐0226
1750‐0227
1750‐0228
1750‐0230
1750‐0231
1750‐0232
1750‐0233
1750‐0234
1750‐0235
1750‐0236
1750‐0237
1750‐0238
1750‐0239
1750‐0240
1750‐0241
1750‐0242
1750‐0243
1750‐0244
1750‐0245
1750‐0246
Description
12 volt electrical outlet in the cab wired through ignition. Location: [#LOC].
Control push button switch center electrical cover offset to officer side for air horns
Engine Compartment Light LED for Freightliner Chassis (EA).
Engine Compartment Light for Freightliner Chassis (EA).
Whelen 4'' round LED amber jacks down light IPOS. Model 20A00FCR light with 2FLANGEC bezel.
Mount customer supplied antenna on cab roof. Location: (1) shark fin centered on cab roof between a/c condensor and storage box terminating below officer seat.
Omit Freightliner Chassis Taillight Programming. Assure Data Code 294‐046 is in Chassis Specification.
Control Push Button Switch for Air Horns on Officers Side of Console.
Light Whelen model PSA00FAR LED (3) amber. Horizontally mounted flashing strip light on each of the interior lower cab door panels outboard. Wire through door switch.
Incandescent Red/White domes and upper NFPA step lighting. Package includes two lights mounted in the front and two mounted in the rear of the cab. White light wire through door and light assembly mounted switch. Red light through light assembly mounted switch. Upper cab step areas to have for NFPA incandescent step lighting. Step lighting to be positioned per OEM recommendations for best compliance to NFPA.
Customer supplied radio and antennas to be installed by Tri‐Co Communicaitons.
Digital speedometer officer's side overhead.
English dominant main cab gauge cluster. Custom ES.
Metric dominant main cab gauge cluster. Custom ES.
Block heater 1000 watt. Includes 15 amp inlet receptacle located outside driver's door next to handrail. Custom ES.
English dominant main cab gauge cluster. 2010 EPA Custom ES.
Metric dominant main cab gauge cluster. 2010 EPA Custom ES.
Interior and exterior NFPA cab lighting package for (2) dr chassis. Consists of (2) incandescent interior and (2) incandescent under cab lights.
Interior and exterior NFPA cab lighting package for (4) dr chassis. Consists of (4) incandescent interior and (4) incandescent under cab lights.
Interior and exterior NFPA cab lighting package for (4) dr chassis (International). Consists of (4) incandescent interior and (4) incandescent under cab lights.
Interior and exterior NFPA cab lighting package for (2) dr chassis (International). Consists of (2) incandescent interior and (2) incandescent under cab lights.
Interior and exterior NFPA cab lighting package for (2) dr chassis. Consists of (2) incandescent interior and (2) incandescent under cab lights.
Interior and exterior NFPA cab lighting package for (4) dr chassis. Consists of (4) incandescent interior and (4) incandescent under cab lights.
Interior and exterior NFPA cab lighting package for (2) dr chassis. Consists of (2) incandescent interior and (2) incandescent under cab lights.
PRICE
$64.00
$100.00
$255.00
$136.00
$197.00
$184.00
$0.00
$100.00
$621.00
$675.00
$849.00
$605.00
$0.00
$312.00
$330.00
$0.00
$0.00
$0.00
$161.00
$161.00
$0.00
$0.00
$161.00
$0.00
Option No.
1750‐0247
1750‐0249
1750‐0250
1750‐0251
1750‐0252
1750‐0253
1750‐0254
1750‐0255
1750‐0256
1750‐0257
1750‐0258
1750‐0259
1750‐0260
1750‐0261
1750‐0262
1750‐0263
1750‐0264
1750‐0265
1750‐0266
1750‐0267
1750‐0268
1750‐0269
1750‐0270
1750‐0271
1750‐0272
Description
Interior and exterior NFPA cab lighting package for (4) dr chassis. Consists of (4) incandescent interior and (4) incandescent under cab lights.
Dome/Pump panel Lts 4" Red/White LED top mount enclosed cab. Package includes (4) light assemblies evenly spaced over top mount enclosed pump panel. White light wire through door and light assembly switch. Red light through light assembly switch.
Dome Lt Red/White LED additional (EA). White light wire through door and light assembly switch. Red light through light assembly switch. Location: Rear facing engine cover seat(s).
Locate inlet receptacle a minimum of 3" rearward of driver cab handrail.
Kussmaul mounting plate model 091‐9H for 12v air compressor.
Courtesy light for officer foot switch(es)wired through marker lights. Whelen model 0SC0EDCR clear light. Quest with heat to feet only.
Stream Light model SL‐20X‐LED black handheld flashlight package. Includes (5) flashlights, (1) single 120V flashlight charger located officer side engine cover ahead of 3X3 and (1) 5‐unit 120V charger located on officer engine cover rearward of 3X3.
Stream Light Vulcan LED orange handheld lantern package. Includes (4) lanterns with 120V charger and vehicle mounts located in driver side rear wall medical cabinet on top shelf, (2) over (2). Includes shelf to be angled forward for ease of viewing.
Auto eject block heater receptacle inlet 15amp with a [#COL] cover. Location: [#LOC].
Aerial PTO hourmeter in cab IPOS.
Antenna base Tessco P/N 90942 (NMO Motorola Style ‐ also called MATM style) on cab roof package (6). Location: (3) driver side between a/c condensor and storage box terminating below officer seat and (3) officer side between a/c condensor and storage box with (1) terminating in center overhead and (2) terminating in officer dash. See customer layout drawing on file with sales.
Fog Lights Clear Lens (PR) located middle hole of bumper.
Battery charger, Super Smart, 20 amp with 120V Kussmaul HP air compressor.
Clamshell controller mounted on on officer's side cab dash at "A" post for Whelen Howler.
Auto transfer switch 120 volt. Includes 8 place breaker box. Allows interior receptacles to be powered by either shore power or generator. Ship to VanMor for installation.
Radio speakers pair. Locate each side rear cab ceiling. Wiring to terminate in center dash for customer supplied radio(s).
Block/oil pan heater on/off 110V switch. Location: inside driver door; rear of seat.
Speedometer for officer side multiplex display.
Dome Lts Red/White Incandescent. Package includes three lights mounted in the front of the cab. White light wire through door and light assembly mounted switch. Red light through light assembly mounted switch.
Battery charger Kussmaul 4000, 45 amp with air compressor.
Battery charger Kussmaul 40 amp model 1200 with 120V HP air compressor.
12ga dedicated ground wire to center overhead console.
Control push‐button switch officer side (side facing) of center electrical cover for Q2B siren.
Control push‐button switch officer side (side facing) of center electrical cover for air horns.
Kussmaul battery charger with air compressor and air inlet. The battery charger receptacle and air inlet to include auto‐eject. Locate to driver side body above vacuum pump access.
PRICE
$161.00
$1,979.00
$214.00
$0.00
$86.00
$136.00
$1,210.00
$1,257.00
$546.00
$143.00
$582.00
$100.00
$1,746.00
$131.00
$798.00
$287.00
$181.00
$0.00
$402.00
$2,553.00
$2,543.00
$83.00
$100.00
$100.00
$1,885.00
Option No.
1750‐0273
1750‐0275
1750‐0276
1750‐0277
1750‐0278
1750‐0279
1750‐0280
1750‐0281
1750‐0282
1750‐0283
1750‐0284
1750‐0285
1750‐0286
1750‐0287
1750‐0288
1750‐0289
1750‐0290
1750‐0291
1750‐0292
1750‐0293
1750‐0294
1750‐0295
1750‐0296
1750‐0297
1750‐0298
Description
Kussmaul battery charger. The battery charger receptacle and air inlet to include auto‐eject. Locate to driver side body above vacuum pump access. No compressor required with charger
Receptacle inlet 30amp household with a [#COL] cover. Location: [#LOC].
Battery charger Newmar model EV‐40‐12‐1, 40amp.
Provide 30 amp radio circuit with 6' of wire Locate in Map Box for customer installed radios.
Light Whelen LED strip model PSC0CDCR to illuminate cab floor. Horizontally mounted on seat riser. Wire through door switch. Location: [#LOC]
Clamshell controller mounted on on officer's side of engine cover for Q2B. Switch to be on top horz surface next to dash.
An Akron directional finder shall be mounted in clear view of the driver and officer within the cab. It shall in. This roof turret electronic azimuth shall clearly identify roof turret directional aim at all times after the master power switch has been activated.
Safety Vision Safedrive Mini DVR. Locate officer side of center windshield post up high.
Auto‐Eject receptacle inlet 20 amp located below the driver's door with a red cover. Receptical to be wired to heaters on tank inlet / out collars. WaterMaster only.
LED cab headlights. TyphoonX, CIIX and QST2 only.
Switch additional guarded toggle. Location and Function: [#LOC].
The chassis shall be pre‐wired for installation of tire chains. Includes guarded toggle switch located on the driver side diagnostic panel.
Receptacle block heater inlet 20amp with a [#COL] cover. Location: [#LOC].
Door ajar indicator light shall be upgraded to larger LED indicator light IPOS.
The master power switch shall be relocated from its standard position to a location that allows the switch to be activated from a standing location with the driver's door open.
Battery charger Kussmaul 4000, 45 amp
Light Weldon LED model 2631‐000‐30 to illuminate cab floor. Horizontally mounted on seat riser. Wire through headlight switch. Location: driver and officer seat riser.
Keyed ignition switch. Keyed same as cab doors. Includes (6) additional keys.
Cyber Dyne digital voltmeter in cab with blue display. Location: Driver side overhead console.
Dome Lts Red/White Incandescent additional. White light wire through door and light assembly mounted switch. Red light through light assembly mounted switch. Location: driver and officer seats.
Kussmaul ignition safety lock model 091‐160. Includes switch on dash for activation labeled "OVERRIDE" with yellow guard. Cab door windows to be disabled with activation.
Turn signal shall not provide an audible indicator, visual only.
Flexible 2" conduit with connectors. Location: Center cab dash to body.
Dome Lts Red/White Incandescent additional. White light wire through door and light assembly mounted switch. Red light through light assembly mounted switch. Location: Centered front of cab for weapons storage.
Hella Xenon work lamp model AS300 (6) Pkg. Includes (2) AS300CR and (4) AS300LR and switch accessible to driver in cab. Location: AS300CR located outboard forward facing on light tower shield, (2) AS300LR each side evenly spaced between command light and outboard light on front of shield.
PRICE
$1,196.00
$582.00
$1,531.00
$124.00
$161.00
$131.00
$981.00
$2,041.00
$601.00
$1,656.00
$212.00
$446.00
$304.00
$186.00
$25.00
$1,641.00
$291.00
$291.00
$245.00
$151.00
$615.00
$0.00
$669.00
$151.00
$5,433.00
1750‐0311
1750‐0312
1750‐0313
1750‐0314
1750‐0315
1750‐0316
1750‐0317
1750‐0318
1750‐0319
1750‐0320
1750‐0321
Description
Trilinear rod antenna model BMEFC24005 with K794 mount with RG58/U coaxial cable. Ship loose.
Radio AM/FM/CD/weather band w/auxiliary input port located [#LOC].
Battery saver to be located [#LOC].
Control push‐button switch officer side ovherhead for Rumbler.
Aerial engagement switch to be guarded style located on the panel outboard of the steering wheel below dash.
Radio Pioneer DEH‐X 7500HD AM/FM CD/USB located [#LOC].
Dome lts Whelen red/white 4" LED (6). Lights to be located two front and four rear. White light wired through door and light assembly mounted rocker switch. Red light through light assembly mounted rocker switch.
Radio speakers additional pair Pioneer TS‐G1341R. Locate each side rear cab ceiling.
Three (3) Aux 12V center console circuit. 30AMP auto reset brkr. 6' minimum wire to power customer supplied devices (modify existing auxiliary power already standard in center console).
Battery charging connector 12V Anderson with weatherproof cover. Includes mating connector (ship loose). Location: Driver's door step area.
Air horn switch on passenger side wall of mic box on rear cab wall. Switch to be labeled ''Evacuation Alert''.
Clamshell controller mounted on officer's side of engine cover for Federal Signal Rumbler.
Tesco GPS antenna model #345146 located on the forward center cab roof between light bars with coaxial cable routed to center cab dash.
Tesco antenna model #418697 with coaxial cable. Ship loose.
Havis model CG‐X computer charge guard located in cab at MDT mount.
Battery charger Kussmaul model 12 HO PIM, 20 amp. Includes model 091‐189‐12 indicator located adjacent to inlet receptacle.
Rear upper window wipers (PR). Top mount enclosed cab only. Requires 4" cap.
Switch horn button two position DOT/Rumbler.
Auto‐Eject receptacle inlet 20 amp located driver side rear of body above tail lights in diamond plate box with a yellow cover.
Flexible 1" conduit with connectors. Location: Center cab dash to antenna rack.
Control push‐button switch officer side (side facing) of center electrical cover for EQ2B siren.
Conduit flexible .75" for radio installation distribution box to officer's overhead.
ATC/KD driving lights (PR) with rubber housings. Includes switch in cab accessible to driver. Location: [#LOC].
1750‐0322
Light Whelen model PSC00FCR LED (4) clear. Vertically mounted flashing strip light with 14 flash patterns including steady burn shall be mounted on the lower cab step well areas (interior). The front doors shall have (1) strip light shall be located on forward step well wall (both sides). The rear doors shall have (1) strip light shall be located on rear step well wall (both sides). Wire through door switch.
Option No.
1750‐0299
1750‐0300
1750‐0301
1750‐0302
1750‐0303
1750‐0304
1750‐0305
1750‐0306
1750‐0307
1750‐0308
1750‐0309
1750‐0310
1750‐0323
1750‐0324
1750‐0325
1750‐0326
Engine tunnel to be fitted with a position activation switch to activate engine compartment lighting when not in the fully closed position.
Air compressor, Kussmaul model 091‐9 12V.
Pigtail, minimum of 18" of wire for service of the battery charger and/or air compressor.
Auto transfer switch 120 volt. Includes 2 place breaker box. Allows interior receptacles to be powered by either shore power or generator.
PRICE
$412.00
$742.00
$0.00
$100.00
$232.00
$1,022.00
$3,127.00
$365.00
$67.00
$304.00
$149.00
$131.00
$308.00
$300.00
$152.00
$1,473.00
$1,462.00
$105.00
$728.00
$317.00
$100.00
$317.00
$899.00
$829.00
$524.00
$989.00
$51.00
$776.00
Option No.
1750‐0327
1750‐0328
1750‐0329
1750‐0330
1750‐0331
1750‐0332
1750‐0333
1750‐0334
1750‐0335
1750‐0336
1750‐0337
1750‐0338
1750‐0339
1750‐0340
1750‐0341
1750‐0342
1750‐0343
1750‐0344
1750‐0345
1750‐0346
1750‐0347
1750‐0348
1750‐0349
Description
Switch momentary to activate heat option contained in mirrors for 10 minutes. The heat will automatically turn itself off after the heat activation time period (10 minutes) has expired.
Auto transfer switch 120 volt. Includes 8 place breaker box. Allows interior receptacles to be powered by either shore power or inverter.
Cornering light relay circuits for lights in center of rear tandem wheel well. Includes (2) relays. Requires scene light option. Interlocked with park brake.
Dome Lt Red/White LED additional (EA). White light wire through door and light assembly switch. Red light through light assembly switch. Location: centered between rear cab dome lights.
Control push‐button switch driver side (side facing) of center electrical cover for EQ2B siren.
Dome lights Red/White incandescent. Package includes two lights mounted in the front and two mounted in the rear of the cab Trucklite 80 series with push style on/off button (may be used with Ford chassis). White light wire through door and light assembly mounted switch. Red light through light assembly mounted switch.
Dome lights White incandescent. Package includes two lights mounted in the front and two mounted in the rear of the cab Trucklite 80 series with push style on/off button (may be used with Ford chassis). Lights wire through door and light assembly mounted switch.
Dome lights White incandescent. Package includes two lights mounted in the front of the cab Trucklite 80 series with push style on/off button (may be used with Ford chassis). Lights wire through door and light assembly mounted switch.
Metric speedometer, in English dominant main cab gauge cluster.
Whelen traffic advisor control head (model TRACTRL1A) shall be mounted in the center overhead panel. The control head shall be wired to the main power switching circuit. There shall be a 50' control cable (model TAPVC50) ran from the control head to the rear of the body, coiled up for dealer supplied and installed traffic advisor.
Garmin GSP 18X USB. May be mounted at E‐ONE discretion on the cab roof within reach of cab 12VDC hot outlet(s).
Radio Pioneer DEH‐3300UB AM/FM CD/USB (with a pair of TS‐D1302R speakers) located [#LOC].
Radio speakers additional pair Pioneer TS‐D1302R. Locate each side rear cab ceiling.
Control push‐button switch officer side (side facing) of center electrical cover for EQ2B siren brake.
Transverse cab compartment dome light package (4) LED. Trucklite 44 series.
Battery charger Kussmaul model 12 HO PIM, 20 amp. Includes model 091‐189‐12 indicator located behind driver's door adjacent to exterior handrail.
Battery charger E‐ONE LPC 20. 120 volt inlet, 20 amp output.
Battery charger E‐ONE LPC 40. 120 volt inlet, 40 amp output.
Battery charger E‐ONE LPC 20. 240 volt inlet (50/60 hz), 12 volt 20 amp output.
Battery charger E‐ONE LPC 20. 240 volt inlet (50/60 hz), 24 volt 20 amp output.
Battery charger with indicator, inlet receptacle and air inlet with mounting plate. Locate to driver side of cab below driver door opening.
Dome Lt Red/White LED additional (EA). White light wire through door and light assembly switch. Red light through light assembly switch. Location: driver seat, officer seat and center for weapons storage.
Flexible 3/4" conduit with connectors. Location: behind officer seat to antenna rack.
PRICE
$204.00
$798.00
$432.00
$214.00
$100.00
$588.00
$588.00
$294.00
$2,258.00
$1,056.00
$258.00
$1,022.00
$365.00
$100.00
$606.00
$1,473.00
$633.00
$963.00
$837.00
$761.00
$0.00
$214.00
$461.00
Option No.
1750‐0350
1750‐0351
1750‐0353
1750‐0354
1750‐0355
1750‐0356
1750‐0357
1750‐0358
1750‐0360
1750‐0361
1750‐0362
1750‐0363
1750‐0364
1750‐0365
1750‐0366
1750‐0367
1750‐0368
1750‐0369
1750‐0370
1750‐0372
1750‐0374
Description
Install customer supplied radio/intercom (ea). Loc: [#LOC].
Kussmaul solar power charging system; model 092‐1220‐1. Location: Center rear cab roof.
Dome Lts Red/White LED. Package includes two lights mounted in the front and three mounted in the rear of the cab. White light wired through door and light assembly switch. Red light through light assembly switch.
Tesco GPS antenna model #GPSNMO‐02 located on the forward center cab roof between light bars with coaxial cable routed to center cab dash.
Each 110 volt cab receptacle shall have a dedicated breaker within the breaker box. This is to provide each cab mounted receptacle (single outlet, duplex, etc. as applicable) with its own isolated circuit.
Radio speaker (1). Locate center rear ceiling. Wiring to terminate in center overhead console for customer supplied radio.
Mount GPS antenna on cab roof. Location: [#LOC].
Antenna base Tessco P/N 90942 (NMO Motorola Style ‐ also called MATM style) on cab roof package (5). Locations: (1) each side rearward of light bar (1) each side forward of the vista. These (4) shall be positioned side to side as required to prevent interference with light tower and its operation. There shall be (1) additional mounted on the officer side rear corner of the cab roof. All (5) shall have coax cable terminating below the officer seat.
Auto‐Eject receptacle inlet 30 amp 240 volt located [#LOC] and with a [#COL] cover.
Cab quad headlights in front bumper in addition to standard headlights.
Stand alone J1939 CAN information display, to include odometer reading. The display is 2" in diameter, intuitive menu driven user interface accessed by (3) built in tactile switches for easy display configurations of active J1939 data and stored faults. Location: [#LOC].
Location for customer supplied speaker as part of customer supplied radio/intercom. Location: [#LOC].
Cab quad headlights below front bumper in addition to standard headlights. The headlights shall be mounted in a tread plate box that will extend the full depth and width of the hose trays mounted within the bumper ext. on each side.
Auto transfer switch 120 volt. Includes 8 place breaker box. Provides for all interior receptacles and Four (4)interior 110v fluorescent lights to be powered by shore power or generator.
The auto transfer switch/breaker box shall be located: body interior just inside L3 entrance door on the left side up high above L2 mounted inboard of the main breaker box.
Stream Light Vulcan LED orange handheld lantern package. Includes (4) lanterns with 120V charger and vehicle mounts. Mount as directed during final inspection.
Dome Lts Red/White 4" LED (6). Lights to be located two front and four rear. White light wired through door and light assembly mounted rocker switch. Red light through light assembly mounted rocker switch.
Guard. On‐Spot activation switch shall have a red flip up safety guard. The switch shall de located on the driver side overhead panel offset to the officer side as far as possible.
Engine hourmeter in cab.
12 VDC (or 24VDC) electrical outlet in the cab wired battery hot with 14AWG at each seated position. Outlets are shared within the same circuit.
Light Whelen model PSB00FBR LED (4) blue. Horizontally mounted flashing strip light on each of the inside lower cab door panels. Wire through door switch.
PRICE
$526.00
$2,484.00
$1,082.00
$342.00
$280.00
$146.00
$0.00
$491.00
$878.00
$536.00
$798.00
$0.00
$604.00
$798.00
$0.00
$1,257.00
$2,375.00
$54.00
$166.00
$254.00
$829.00
Option No.
1750‐0375
1750‐0376
1750‐0377
1750‐0378
1750‐0379
1750‐0380
1750‐0381
1750‐0382
1750‐0383
1750‐0384
1750‐0385
1750‐0386
1750‐0387
1750‐0388
1750‐0389
1750‐0390
1750‐0391
1750‐0392
1750‐0393
1750‐0394
1750‐0395
1750‐0396
1750‐0397
1750‐0398
1750‐0399
Description
Switch console mounted to the driver side engine cover.
Light Whelen model PSR00FRR LED (3) red. Horizontally mounted flashing strip light on each of the inside lower cab door panels. Wire through door switch.
Additional 4" white LED dome lights (PR) for rear of cab wired battery hot to a 15 min. timer switch. Locate switch on interior officer side rear side wall just above floor level.
Switch momentary to illuminate cab dome lighting for 15 minutes. The lights will automatically turn themselves off after the activation time period (15 minutes) has expired. Locate switch on interior officer side rear side wall just above floor level.
Auto transfer switch 120 volt. Includes 12 place breaker box. Provides for all 110v interior receptacles and up to four (4) interior fluorescent lights to be powered by shore power or generator.
35 AMP inline fuse as hot lead for radio installation. Radio circuit with G30060‐1CR in‐line fuse 35 amp. Fuse wired to ignition side to power the radio head. To be labeled and identified as ''HOT''. In‐line fuse to be clearly labeled. Wiring located behind a face plate in the center overhead also provide ground wire and label wires. Label ground ''Chassis Ground''. Fuse to be down line from standard fuse and accessible for Motorola Spectra 800 MHz radio.
Cornering light relay circuits for cab/body lights on side of unit. Includes (2) relays. Interlocked with park brake.
Conduit flexible 3/4" from center cab desk raceway to receptacle located at upper center in R1.
Radio Jensen JHD1630B AM/FM/WB (with a pair of Polk Audio DXi525 5.25" speakers) located [#LOC].
Light Weldon LED model 2631‐000‐30 to illuminate cab floor. Horizontally mounted on seat riser. Wire through headlight switch. Location: below each rear wall seat on riser.
Cab step lighting package. Includes (2) EON LED lights per side IPOS. (1) Light per door mounted in the cab step well area
The FoamPro controller shall be located in cab centered between driver and officer.
Golight controls shall be located [#LOC].
Handheld Flashlight, black Streamlight SL‐20X with 12 VDC charger. Location: driver and officer rear cab wall outboard below seat support channel.
Radio speakers pair. Locate (1) above officer and (1) centered in rear crew cab area. Wiring to terminate (1) center dash, (1) center overhead for customer supplied radio(s).
Radio Poly‐Planar AM/FM CD/MP3 with USB port located center overhead console offset to officer side.
Receptacle inlet 50amp 250V located in air compressor compartment with cover and manual 4 pole 100A transfer switch. Allows Bauer air compressor to be powered by either shore power or 3 phase generator.
Battery charger Kussmaul 75 amp model 091‐149‐12 with 091‐9 air compressor.
Switch secondary braking three position Jacobs/Off/Telma. Jacobs Brake top position, off center, Telma bottom position.
Control push button switch for Q2B on officers side of console.
Light EON LED to illuminate cab floor(EA). Horizontally mounted on seat riser. Wire through door switch. Location: [#LOC].
Control push‐button switch on officer's overhead for Q2B siren brake.
Mount customer supplied antenna on cab roof. Location: centered behind lightbar, driver side forward on vista roof, officer side forward on vista roof and officer side rear cab roof. All terminating in overhead command area cabinet.
Mount customer supplied GPS antenna on interior of cab. Location will be per antenna manufacturers' recommendation.
Control push‐button switch driver side of center dash upper tier for Q2B siren.
PRICE
$167.00
$624.00
$503.00
$263.00
$1,128.00
$593.00
$432.00
$380.00
$1,138.00
$291.00
$263.00
$0.00
$0.00
$234.00
$287.00
$909.00
$3,792.00
$3,689.00
$218.00
$100.00
$161.00
$100.00
$732.00
$184.00
$100.00
Option No.
1750‐0400
1750‐0401
1750‐0402
1750‐0403
1750‐0404
1750‐0405
1750‐0406
1750‐0407
1750‐0408
1750‐0410
1750‐0411
1750‐0412
1750‐0413
1750‐0414
1750‐0415
1750‐0416
1750‐0417
1750‐0418
1750‐0419
1750‐0420
1750‐0423
1750‐0424
1750‐0425
Description
Cyber Dyne digital voltmeter in cab with blue display. Location: Driver side cab dash, side facing, adjacent to park brake release.
Cornering light relay circuits for only the side facing gravel shield lights. Includes (2) relays. Requires scene light option. Interlocked with park brake.
Install six (6) customer supplied radio cables. (3) 30' Cables will run from behind driver seat to center of dash. (3) 17' Cables will run from behind driver seat to the overhead cabinet area in cab.
Install radio interface cable for Motorola model APX 6500. Run cable from back of driver seat to center of dash. The interface cable shall consist of the following FireCom cables PN 110‐5136‐30 (4' interface cable), PN 108‐0086‐00 (15' extension cable), PN 108‐0085‐00 (10' extension cable) for a total of 29' in length.
Dome lights Whelen red/white 6" Super‐LED surface mounted interior lights. Four (4) model 60CREGCS lights to be located two front and two rear. White light wired through door and light assembly. Red light through switch mounted on light assembly.
Battery charger Kussmual model 091‐200‐12‐194‐WT‐RD. 120 Volt 40 Amp output includes water tight display mounted adjacent to inlet.
The air horn(s) shall not be included within the Multiplex system (separate switching from Multiplex display required).
Control push‐button switch for Rumbler. Location [#LOC].
Mount customer supplied (1) radio cable and (4) antennas. Antenna locations: (1) driver and officer side forward cab roof, (1) driver and officer side rearward cab roof. Route all cables to upper rear wall medical cabinet. Route radio cable from center of dash to upper rear wall of medical cabinet.
Switch, additional through multiplex display. Function: [#LOC].
Dome Lts Red/White Whelen model 60CREGCS LED. Package includes two lights mounted in the front and four mounted in the rear of the cab. White light wired through door and light assembly switch. Red light through light assembly switch.
Kussmaul digital battery display model 091‐194‐IND‐WT‐RD in place of standard.
Dual USB charger socket in the cab wired battery hot. Location: [#LOC].
Warning light Whelen M6R series Linear Super LED (PR) red. Location: interior of canopy doors wired through each door ajar switch only.
Dome Lt Red/White LED additional (EA). White light wire through door and light assembly switch. Red light through light assembly switch. Location: Below forward vista medical cabinet.
30 AMP inline fuse as hot lead for radio installation. Radio circuit with in‐line fuse 30 amp. Fuse wired to ignition side to power the radio head. To be labeled and identified as ''HOT''. In‐line fuse to be clearly labeled. Wiring located in the interior of the center console also provide ground wire and label wires. Label ground ''Chassis Ground''.
Flexible 1" conduit with connectors. Location: radio cabinet to center of dash.
Conduit, flexible 1" with connectors. Location: Bottom of cab mounted center console to forward corner of counter top on driver side of body.
Turn signal TecNiq LED amber strip (PR) located in center of quad headlight bezel (QST2 only).
Daytime Running Light TecNiq LED strip (PR) located in center of quad headlight bezel (QST2 only).
Programming instructions for auxiliary switch 1 on steering wheel switch pod. Switch function: [#LOC].
Programming instructions for auxiliary switch 2 on steering wheel switch pod. Switch function: [#LOC].
Programming instructions for auxiliary switch 3 on steering wheel switch pod. Switch function: [#LOC].
PRICE
$245.00
$432.00
$762.00
$656.00
$1,403.00
$1,846.00
$406.00
$100.00
$734.00
$95.00
$1,748.00
$361.00
$151.00
$748.00
$214.00
$593.00
$317.00
$317.00
$114.00
$123.00
$95.00
$95.00
$95.00
1750‐0448
1750‐0449
Description
Turn signal Weldon LED amber pair located [#LOC].
Antenna base Tessco P/N 90942 (NMO Motorola Style ‐ also called MATM style) on cab roof. Location: (4) vista cab roof, (4) front cab roof. See sales for exact location labeling instructions.
Interior courtesy red LED light package. Includes driver / officer side engine cover lighting, center dash wash lights and front / rear floor lights.
Dual USB charging ports in the cab wired battery hot. Location: [#LOC].
Weldon guard model 2034‐0000‐00 for horizontally mounted seat riser light (EA).
Conduit flexible 1" for radio installation center of dash to area behind officer's seat.
Flexible 1" conduit with connectors. Location: behind officer seat to antenna rack.
Battery charger Kussmaul LPC 80. 120 volt inlet, 80 amp output.
Radio cabinet ventilation fan (PR). Location: ceiling of radio cabinet wired through ignition.
Halogen cab headlights. TyphoonX, CIIX and QST2 only.
Dome Lt Red/White LED additional (EA). White light wire through door and light assembly switch. Red light through light assembly switch. Location: center between front cab seats.
The chassis shall be pre‐wired for installation of tire chains. Includes guarded toggle switch located on the center dash panel.
Radio AM/FM CD with weather band located [#LOC]. Includes speakers in ceiling to rear of driver/officer.
Dome Lt Red/White Whelen model 60CREGCS LED additional (EA). White light wired through door and light assembly switch. Red light through light assembly switch. Location: center rear crew cab ceiling.
Switch horn button three position DOT/air horn/electronic siren. Wired through multiplex display screen.
Battery charger Kussmaul model EV40, 40 amp.
Light EON LED (EA). Horizontally mounted in seat riser. Wire through door switch. Location: officer seat riser.
Dome Lts Red/White Whelen model 60CREGCS LED. Package includes two lights mounted in the front of the cab. White light wired through door and light assembly switch. Red light through light assembly switch.
Battery charger Iota model DLS‐45, 45 amp.
Clamshell controller mounted on center console offset to officer side for air horns.
Wire battery charger using cord connectors ipo hardwire.
Dome Lts Red/White Whelen model 60CREGCS LED. Package includes two lights mounted in the front and two mounted in the rear of the cab. White light wired through door and light assembly switch. Red light through light assembly switch.
Light Whelen model PSRASXCR LED (4) red/amber. Horizontally mounted flashing strip light on each of the inside lower cab door panels. Wire through door switch.
Momentary DPF regeneration override switch.
1750‐0450
Steering wheel with switch pods IPOS. Includes wiper functions, master warning sw, air horn sw, aux brake on/off and (3) aux switches. Required with Typhoon and CII equipped with 4Front and QST2. (Requires seperate programming options to activate aux switches)
$0.00
1750‐0451
Steering wheel with switch pods IPOS. Includes wiper functions, master warning sw, air horn sw, aux brake on/off and (3) aux switches. For use only with Typhoon and CII NOT equipped with 4Front. (Requires seperate programming options to activate aux switches)
$953.00
Option No.
1750‐0426
1750‐0427
1750‐0428
1750‐0429
1750‐0430
1750‐0431
1750‐0432
1750‐0433
1750‐0434
1750‐0435
1750‐0436
1750‐0437
1750‐0438
1750‐0439
1750‐0440
1750‐0441
1750‐0442
1750‐0443
1750‐0444
1750‐0445
1750‐0446
1750‐0447
PRICE
$570.00
$888.00
$380.00
$73.00
$19.00
$317.00
$461.00
$1,767.00
$229.00
$0.00
$214.00
$446.00
$849.00
$352.00
$212.00
$1,604.00
$161.00
$583.00
$621.00
$131.00
$0.00
$1,166.00
$862.00
$212.00
Option No.
1750‐0452
1750‐0453
1750‐0454
1750‐0455
1750‐0457
1750‐0458
1750‐0459
1750‐0460
1750‐0461
1750‐0462
1750‐0463
1750‐0464
1750‐0465
1750‐0466
1750‐0467
1750‐0468
1750‐0469
1750‐0470
1750‐0471
1750‐0472
1750‐0473
1750‐0474
1750‐0475
1750‐0476
1750‐0477
1750‐0478
1750‐0479
1750‐0480
1750‐0481
1750‐0482
1750‐0483
Description
Radio speakers (3). Locate officer ceiling and each side rear cab ceiling. Wiring to terminate in center overhead console for customer supplied radio(s).
Auto transfer switch 120 volt. Includes 12 place breaker box. Allows interior receptacles to be powered by either shore power or generator.
Courtesy light for driver and officer located on front of risers wired through marker lights. Whelen model 0SR00SCR light.
Block heater connector; 15 amp male. Location: driver side under front bumper adjacent to frame rail.
Turn signal Whelen 600 LED amber arrow pair with black bezel located [#LOC].
Quad bezels (4) black ipos.
Rear cab dome lights located inboard even with 3x3 posts with white light facing inboard.
Light Whelen model PSR00FRR LED (4) red. Horizontally mounted flashing strip light on each of the inside cab door panels below the windows. Wire through door switch.
Remove switch pods from 4Front steering wheel and install std switches for relevant functions.
Turn signal Whelen M6 LED arrow amber pair with clear lenses located [#LOC].
Handheld flashlight, Streamlight Vulcan LED Model 44401 flashlight with vehicle mount system. Location: [#LOC].
Dome Lt Red/White Whelen model 60CREGCS LED. One (1) light centered between driver/officer in the ceiling. White light wired through door and light assembly switch. Red light through light assembly switch.
Receptacle inlet 50A 230V located in the air compressor compartment with cover and manual 3 pole 100A transfer switch. Allows compressor to be powered by either shore power or generator.
DEF level gauge adjacent to tank fill area.
Officer side push button switches centered on dash.
Relocate driver master power window controls and officer front window control to center upper tier.
Flexible 3/4" conduit with connectors. Location: center cab dash to rear medical cabinet upper area.
Relocate driver master power window controls to cab dash upper tier offset to driver.
Auto‐Eject receptacle inlet 20 amp located rear of body driver side with a Yellow cover. Receptacle wired to roof top A.C.
Center 12V distribution module under center cab dash electrical cover acces door to be re‐located to officer side below access door and remove standard bracket. See sales for details.
Siren brake locate center dash
Control push button switch center dash upper tier offset to officer side for air horns
Control push‐button switch center dash upper tier offset to officer for Q2B.
Speaker wire for dealer/customer supplied radio/speaker. Route wire from driver side 3x3 up high to center dash.
Clamshell controller mounted on officer's side of engine cover for Q2B brake.
Battery charger Kussmaul model 091‐216‐40/20, 40 amp battery charger / 20 amp battery saver.
On‐Spot activation switch to have a red cover (or bezel).
Auto‐Eject dual receptacle inlet; 30 amp 120V with air auto eject located [#LOC] with a [#COL] cover.
Auto‐Eject receptacle inlet 20 amp wired to roof top AC located [#LOC] with a [#COL] cover.
Control push‐button switch officer switch panel for Q2B siren.
Control push‐button switch on officer's switch panel for Q2B siren brake.
PRICE
$493.00
$840.00
$267.00
$106.00
$729.00
$268.00
$0.00
$829.00
$0.00
$682.00
$230.00
$352.00
$3,200.00
$366.00
$0.00
$433.00
$461.00
$433.00
$601.00
$0.00
$96.00
$100.00
$100.00
$155.00
$131.00
$2,088.00
$41.00
$1,582.00
$601.00
$100.00
$100.00
Option No.
1750‐0484
1750‐0485
1750‐0486
1750‐0487
1750‐0488
1750‐0489
1750‐0490
1750‐0491
1750‐0492
1750‐0493
1750‐0494
1750‐0495
Description
Control push‐button switch officer switch panel for siren.
Control push‐button switch officer switch panel for air horns.
Battery charger Kussmaul model Pump Plus 1200, 40 amp.
Customer supplied radio cable. Route from upper rear wall medical cabinet to pump operator panel.
Ammeter gauge in cab 0‐300 amps through multiplex display.
Air compressor to be located floor mounted in officer side wheel well medical cabinet. Includes grating over front for protection.
Lateral "G" Alert system with Audible and Visual warnings.
The chassis shall be pre‐wired for installation of tire chains. Includes 12 volt rocker lock‐out/safety style switch.
Interlock to position front bumper lid for cab tilting.
Rear upper window wipers (3). Requires 4" cap. Switch located on upper rear overhead panel.
Mobility Pro GPS system model BT5830V2‐AT with model ANT‐NA520‐ABC008 antenna.
Kussmaul bluetooth module model 091‐226 wired to cab speakers. Located in cab accessible to driver.
1750‐0496
1750‐0497
1750‐0498
1750‐0499
Courtesy light TecNiq Dragon wired through marker lights. Model D04 [#COL] LED light with S/S horizontal mount. Location: [#LOC].
Additional marker light TecNiq amber LED strip (PR) located in center of quad headlight bezel (QST2 only).
Aerial PTO switch to have a red cover (or bezel).
Ammeter gauge in cab 0‐400 amps through multiplex display.
Relocate driver master power window controls center upper tier offset to driver and officer front window control to center upper tier offset to officer.
Clamshell controller mounted on on driver's side of engine cover for electronic siren.
Auto transfer switch allows hydraulic tool pump to be controlled by a remote switch
Whelen model 01‐066A584152 red courtesy light with 45 degree bezel. Locate on the driver ceiling to illuminate overhead switches. Includes switch adjacent to light.
Radio Delphi AM/FM/Weatherband with CD and aux input and USB port. Located [#LOC].
Dual DPF regeneration override switches. (1) controls manual generation; (1) controls inhibit.
Radio AM/FM CD Kenwood model KDC‐BT762HD located [#LOC].
$117.00
$123.00
$41.00
$794.00
$446.00
$0.00
$793.00
1750‐0510
The chassis shall be pre‐wired for installation of tire chains. Includes guarded toggle switch located on the driver overhead console.
High beam headlight mounted on the inboard position ipos.
Battery charger Iota model DLS‐75, 75 amp.
Auto‐Eject receptacle inlet 20 amp located below the driver's door with a red cover. Receptical to be wired to: Transfer switch/sub breaker box, refrigerator, and module interior receptacles.
1750‐0511
1750‐0512
1750‐0513
1750‐0514
Auto‐Eject receptacle inlet 20 amp located below the driver's door with a red cover. Receptical to be wired to battery charger only.
Windshield fans RoadPro Tornado pair. Location: centered below overhead console.
The commercial chassis shall be pre‐wired for installation of tire chains. Installed by chassis OEM.
Peterson LED cab headlights.
$601.00
$394.00
$565.00
$1,022.00
1750‐0500
1750‐0501
1750‐0502
1750‐0503
1750‐0504
1750‐0505
1750‐0506
1750‐0507
1750‐0508
1750‐0509
PRICE
$100.00
$100.00
$1,502.00
$183.00
$794.00
$129.00
$4,475.00
$565.00
$291.00
$2,192.00
$1,807.00
$363.00
$433.00
$131.00
$776.00
$346.00
$849.00
$423.00
$960.00
$601.00
Option No.
1750‐0515
1750‐0516
1750‐0517
1750‐0518
1750‐0519
1750‐0520
1750‐0521
1750‐0522
1750‐0523
1750‐0525
1750‐0526
1750‐0527
1750‐0528
1750‐0529
1750‐0530
1750‐0531
1750‐0532
1750‐0533
1750‐0534
1750‐0535
1750‐0536
1750‐0537
1750‐0538
1750‐0539
1750‐0540
1750‐0541
1750‐0542
1750‐0543
Description
Flexible 1" conduit with connectors. Location: Center cab dash to pump panel area.
Auto drain, Kussmaul model 091‐9‐086 12V. For use with air compressor 091‐9‐12V only.
Cab headlights Sirius single low/hi beam located recessed behind bumper in addition to front cab mounted quad headlights.
Cab headlights quad Sirius located recessed behind bumper in addition to front cab mounted quad headlights.
Sirius cab headlights. TyphoonX, CIIX and QST2 only.
Conduit, flexible 2" with connectors. Includes (3) three pull wires labled 1 thru 3 each end. Location: Bottom of cab mounted center console to body mounted electronics rack floor area.
Deutsch connector in center cab dash. Wired as follows: blue wire: hot master warning, red wire: hot park brake applied, purple wire: hot left turn signal and green wire: hot right turn signal.
Flexible 2" conduit with connectors. Location: Center cab dash to radio cabinet.
Switch for driver controlled differential lock to be momentary IPOS (Axle lock engages only when switch is pressed and held).
Light Whelen model PSR00FRR LED red, qty one (1). A horizontally mounted flashing strip light shall be provided on the inside rear body entry door panel below the window. Wire through door switch.
Dome Lts Red/White Incandescent. Package includes two lights mounted in the front of the cab. White light wire through door and light assembly mounted switch. Red light through light assembly mounted switch.
Light Whelen model PSR00FRR LED (2) red. Horizontal mounted flashing strip light on each of the inside lower cab door panels. Wire through door switch.
Interlock to prevent cab tilting with aerial in cradle.
Air compressor, Kussmaul model 091‐9‐12V‐HP.
Radio speakers (4). Locate (1) each side front and rear cab ceiling. Wiring to terminate in center lower dash for customer supplied radio(s).
Control push‐button switch center lower dash for Q2B siren.
Control push‐button switch on center lower dash for Q2B siren brake.
Flexible 3/4" conduit with connectors. Location: officer side overhead to behind officer seat.
Flexible 3/4" conduit with connectors. Location: behind officer seat to pump panel area.
Clamshell controller mounted on officer's side switch panel for Q2B brake.
Clamshell controller mounted on officer's side switch panel for Q2B.
Conduit, 1" flexible with connectors, junction box & pull wires. Locate: L1/R1 forward bulkhead. Conduit to begin at same height on bulkhead as hydraulic reel switchs on rearward wall and run vertical to compartment ceiling, then toward chassis centerline terminating at a ceiling mounted junction box with the box oriented so as to accommodate conduit running aft across the ceiling for dealer/customer installed equipment.
Flexible 1" conduit with connectors. Location: Center cab dash to radio cabinet.
PharmGuard dual mode power supply; 110V shoreline and 12V power.
Dual USB charging ports in the cab wired through ignition. Location: [#LOC].
Kussmaul bluetooth module model 091‐226 wired to cab speakers. Located in officer overhead.
PharmGuard dual mode power supply; 110V shoreline and 12V power.
Zoll RescueNet Road Safety driver monitoring system.
PRICE
$377.00
$218.00
$668.00
$837.00
$163.00
$317.00
$535.00
$386.00
$131.00
$208.00
$340.00
$829.00
$517.00
$1,098.00
$656.00
$100.00
$100.00
$461.00
$461.00
$131.00
$131.00
$417.00
$324.00
$542.00
$73.00
$363.00
$542.00
$10,593.00
Option No.
1750‐0544
1750‐0547
1750‐0548
1750‐0550
1750‐0551
1750‐0552
1750‐0553
1750‐0554
1750‐0555
1800‐0000
1800‐0001
1800‐0002
1800‐0003
1800‐0005
1800‐0006
1800‐0008
1800‐0011
1800‐0013
1800‐0014
1800‐0020
1800‐0021
1800‐0022
1800‐0023
1800‐0024
1800‐0025
1800‐0026
1800‐0027
1800‐0028
1800‐0029
1800‐0030
1979
3000‐0000
Description
Control push‐button switch on center console for Q2B siren.
Conduit flexible 1" from center cab dash to upper forward wall of L2.
Flexible 3/4" conduit with connectors. Location: officer side overhead to officer sid of forward vista medical cabinet .
Control push‐button switch center dash upper tier offset to officer for Q2B brake.
Conduit flexible 1" from center cab dash to pump panel.
Battery charger Iota model DLS‐75, 75 amp with IQ4 Smart Controller.
Relocate driver master power window controls to driver overhead and officer front window control to officer overhead.
FireTech LED/halogen cab headlights.
ROM Duro Lumen LED light model RO3853. Location: driver and officer rear cab ceiling outboard.
Cooling system for 2004 compliant engines, Typhoon only.
Cooling for EGR engines. Includes charge air cooler.
Conditioner Cooling System NalCool 2000
Coolant System Overflow Recovery System, CRS‐150
Cooling system for use with Cyclone II X, Typhoon X, and Quest chassis. Includes coolant recovery system.
Remote coolant filter for engine cooling system (Cummins ISC and ISL engines only).
Cooling system Tier II OPTIONAL 125 DEGREE, no fan clutch available.
** USE 1800‐0012 TIER III ENGINE COOLING SYSTEM STANDARD 115 DEGREE.
Cooling system for use with Cyclone II X, Typhoon X, and Quest chassis. For use with 2010 / 2013 / 2016 EPA engines. Includes coolant recovery system.
Cooling system for use with Cyclone II X Hush Mid Engine chassis. Includes coolant recovery system.
Cooling system for 98 EPA non‐EGR engines. Includes charge air cooler.
Cooling system for use with Cyclone II Hush Mid Engine chassis. Includes coolant recovery system. For use with 2010 EPA engines.
Cooling system for use with Navistar MAXXFORCE MF10 2010 EPA engine in Cyclone II X, Typhoon X, and Quest chassis. Includes coolant recovery system.
Cooling for Pre‐2004 export engines. Includes charge air cooler.
Ball valve drain for radiator ipo petcock valve.
Cooling system for use with Navistar MAXXFORCE MF13 2010 EPA engine in Cyclone II X and Quest chassis. Includes coolant recovery system.
Plug shall be installed in drain of radiator IPO petcock valve.
Cummins Compleat (blue) 50/50 pre‐mixed antifreeze ipos.
Cooling system for use with Cyclone HS and Quest HS chassis. For use with 2013 / 2016 EPA engines.
Engine cooler. E‐ONE chassis only. Requires control option for pump panel.
Shutoff valve (1) each side of optional coolant filter.
Dealer installed generator ‐ Space shall be provided for a Harrison 20KW MPC hydraulic generator. Dealer responsible for NFPA required 3rd party generator testing.
Body mainframe and hosebed side assemblies for a 80" high body.
PRICE
$100.00
$461.00
$461.00
$100.00
$461.00
$828.00
$582.00
$2,625.00
$420.00
$6,450.00
$6,685.00
$100.00
$581.00
$6,685.00
$573.00
$11,868.00
$11,444.00
$7,533.00
$14,464.00
$6,685.00
$15,310.00
$8,566.00
$6,685.00
$117.00
$10,624.00
$70.00
$295.00
$7,533.00
$473.00
$143.00
$324.00
$0.00
Option No.
3000‐0004
3000‐0005
3000‐0006
3000‐0012
3000‐0013
3000‐0014
Description
Diamond plate body for use with wide water tank, tandem axle chassis and driver side frame mounted pump. Includes driver and officer side forward lower body compartments (drivers narrow), framed wheel well area with diamond plate corners and flat back style rearend with 12" tailboard.
Diamond plate body for use with wide water tank, tandem axle chassis and individual SM pump module. Includes driver and officer side forward lower body compartments, framed wheel well area with diamond plate corners and flat back style rearend with 12" tailboard.
Diamond plate body for use with wide water tank, single axle chassis and driver side frame mounted pump. Includes driver and officer side forward lower body compartments (drivers narrow), framed wheel well area with diamond plate corners and boxed out style rear tailboard.
Diamond plate body for use with narrow water tank, tandem axle chassis with driver side under mount pump and officer side forward discharge/intake panel. Includes driver and officer side forward and rearward lower body compartments, framed wheel well area with diamond plate corners and flat back style rearend with 10" tailboard.
Diamond plate body for use with narrow water tank, under body pump and tandem axle chassis. Includes driver and officer side compartments forward of and rearward of tandem axle, framed wheel well area with diamond plate corners and flat back style rearend with 12" tailboard.
Diamond plate body for use with wide water tank, single axle chassis and driver side frame mounted pump. Includes driver and officer side forward lower body compartments (drivers narrow), framed wheel well area with diamond plate corners and flat back style rearend with 12" tailboard.
PRICE
$7,346.00
$7,575.00
$0.00
$8,265.00
$9,299.00
$7,001.00
3000‐0016
Diamond plate body for use with narrow water tank, tandem axle chassis with driver side under mount pump and officer side forward discharge/intake panel. Includes driver side forward and rearward lower body compartments, officer side (2) forward and (1) rearward lower body compartments,framed wheel well area with diamond plate corners and flat back style rearend with 12" tailboard.
Diamond plate body for use with narrow water tank, tandem axle chassis and driver side frame mounted pump with enclosed pump panel. Includes driver and officer side forward lower body compartments (drivers narrow), framed wheel well area with diamond plate corners and flat back style rearend with 12" tailboard. Oklahoma City.
$9,265.00
3000‐0017
Diamond plate body for use with wide water tank, single axle chassis and individual SM pump module. Includes driver and officer side forward lower body compartments, framed wheel well area with diamond plate corners and flat back style rearend with 12" tailboard.
$10,734.00
3000‐0015
3000‐0018
3000‐0019
3000‐0020
3000‐0021
Diamond plate body for use with wide water tank, single axle chassis and individual SM pump module. Includes driver and officer side forward lower body compartments, framed wheel well area with diamond plate corners and flat back style rearend with 12" tailboard.
Stainless Steel Body Construction. The compartment floors, front panels, vertical side sheets, rear walls, door openings, wheel wells, compartment panels, dividing walls, and reinforcements shall be constructed of 12 gauge 304L stainless steel material.
Wheel well compartment for (2) fire extinguishers, includes SS door painted job color. Available for any type of wheel well panel (each)
304L Stainless Steel formed body construction for Wetside tanker. Includes driver and officer side forward and rear lower body compartments and flat back style rearend with tailboard.
$8,265.00
$10,734.00
$0.00
$1,005.00
$0.00
Option No.
3080‐0000
3080‐0001
3080‐0002
3080‐0003
3080‐0004
3080‐0005
3080‐0006
3080‐0007
3080‐0008
3080‐0010
3080‐0011
3080‐0021
3080‐0027
3080‐0030
3080‐0031
3080‐0032
3080‐0033
3080‐0034
3080‐0035
3080‐0036
3080‐0037
Description
Body aerial 95/CR100 CII/Quest medium cab without pump. 100" wide with L and R extended rescue style high sides and rear side staircases. 61" high body for 11'‐10" OAH.
Body aerial 95/CR100 with center hose bed. Configured for midship pump and 300 tank. 100" wide with L and R extended rescue style high sides and double beavertails. 63" high body for 12'‐1" OAH
Body aerial Bronto RLP. Includes full length hosebed and pocket style flop down steps at each staircase. The doors on compts next to fwd outriggers to match the outrigger covers. The doors on small compts over forward tandem wheel to match wheelwell. The doors at rear of body on the lower aerial control panel compt to match rear body finish.
Body aerial Bronto RLP. Includes deep upper right side compartment, short hosebed and pocket style flop down steps at each staircase. The doors on compts next to fwd outriggers to match the outrigger covers. The doors on small compts over forward tandem wheel to match wheelwell. The doors at rear of body on the lower aerial control panel compt to match rear body finish.
Body aerial HM100/110 with center hose bed. Configured for midship pump and 500 tank. 100" wide with L and R extended rescue style high sides and double beavertails. 67" high body for 11'‐6" OAH.
Body aerial HM100/110 CII without pump. 100" wide with L and R extended rescue style high sides and double beavertails. 67.25" high body for 11'‐5" OAH.
Body aerial HP100 CII without pump. 100" wide tandem axle. (220" WB medium cab / 230" WB long cab). Includes L and R extended rescue style high sides and double beavertails.
Body aerial HP100 with center hose bed. Configured for midship pump and 500 tank. 100" wide body with (230" wheelbase medium cab/240" wheelbase long cab) tandem axle. Includes L and R extended rescue style high sides and double beavertails.
Body aerial HP75 / HP78 with center hose bed. Configured for midship pump and 400‐500 tank. Single axle 100" wide body. Includes L and R rescue style high sides. The rear turntable access door to match the rear body finish.
Body aerial HP75 / HP78 SideStacker Quest / CII / Typhoon with pump. Single axle. Includes pocket style drop down step at left rear staircase. The rear access doors to match the rear body finish.
Body aerial Bronto Q118 with pump. Includes pocket style flop down steps at each staircase. Rear electrical compartment lift‐up door to match rear body finish.
Body boom mid mount 50'. Includes rescue style right side boom compartment.
Body aerial RLP without pump. Includes pocket style flop down steps at each staircase. The doors on compts next to fwd outriggers to match the outrigger covers. The doors on small compts over forward tandem wheel to match wheelwell. The doors at rear of body on the lower aerial control panel compt to match rear body finish.
Tiller body without pump. Includes tool compartment at rear of body below ladder tunnel and staircases with pocket style flop down steps each side of tractor body.
HP95 MidMount front body with pump.
HP95 MidMount front body without pump.
HP95 MidMount front body without pump low travel height (for use with DPF / SCR aftertreatment).
HP95 MidMount center body with pump and 300g tank.
HP95 MidMount center body with pump and 500g tank.
HP95 MidMount center body with pump and 300g tank. Includes optional officer's side compartment above rear wheels.
HP95 MidMount center body with pump and 500g tank. Includes optional officer's side compartment above rear wheels.
PRICE
$60,392.00
$71,243.00
$55,448.00
$56,557.00
$67,877.00
$60,534.00
$62,716.00
$71,967.00
$45,974.00
$50,973.00
$53,859.00
$37,248.00
$53,866.00
$66,086.00
$21,836.00
$21,879.00
$20,847.00
$18,629.00
$18,629.00
$18,913.00
$18,913.00
Option No.
3080‐0038
3080‐0039
3080‐0040
3080‐0041
3080‐0042
3080‐0043
3080‐0044
3080‐0045
3080‐0046
3080‐0047
Description
HP95 MidMount center body without tank.
HP95 MidMount center body without pump with wide ladder tunnel.
HP95 MidMount center body without pump low travel.
HP95 MidMount rear body with hosebed.
HP95 MidMount rear body without hosebed.
HP95 MidMount rear body with narrow hosebed and shallow rescue style officer's side compartments.
HP95 MidMount rear body with wide ladder tunnel and no hosebed.
HP95 MidMount rear body without hosebed low travel.
HP95 MidMount center body with pump and 300g tank. Includes optional officer's side shallow compartment above rear wheels.
HP95 MidMount center body with pump and 500g tank. Includes optional officer's side shallow compartment above rear wheels.
PRICE
$17,635.00
$18,948.00
$18,565.00
$26,079.00
$27,219.00
$28,185.00
$27,219.00
$25,708.00
$19,588.00
$19,588.00
3080‐0054
Body aerial 95/CR100 CII with pump and 500g tank. 100" wide with L and R extended rescue style high sides and double beavertails.
Body aerial HP100 Platform without pump. 100" wide with L and R extended rescue style high sides, seperate rear side compartments and rear side staircases. The door on small compt next to rear outrigger to match wheelwell.
Body aerial HM100 CII without pump ‐ Memphis. Includes left side traditional style extended high sides, combined pltwrk in L6/L7 and L8/L9, half right side with DP panels above and double beavertails. Trans floor 3/16 Dia Plt, others 3/16 SM Plt. Manual cab tilt in R1. 69.25" high body for 11'‐7" OAH.
Body aerial HP75 / HP78 SideStacker Quest / CII / Typhoon with pump. Single axle. Includes extended R1 compt and pocket style drop down step at left rear staircase. The rear access doors to match the rear body finish.
Body aerial HP100 with center hose bed. Configured for midship pump and 300 tall tank. 100" wide body with 230" wheelbase tandem axle. Includes L and R extended rescue style high sides, single right side hose chute and double beavertails.
Body aerial HP75 / HP78 with center hose bed. Configured for midship pump and 400‐500 tank. Single axle 100" wide body. Includes L and R rescue style extended high sides. The rear turntable access door to match the rear body finish.
Body aerial HP75 / HP78 with combined extended height front side compts, beavertail compts combined w/rear side compts and center hose bed. Configured for midship pump and 400‐500 tank. Single axle 100'' wide body. The rear turntable access door to match the rear body finish.
Body aerial HP75 / HP78 SideStacker Quest / CII / Typhoon with pump. Single axle. Right side ahead of rear axle to have two seperate compts, 24"w R1 and 32"w R2. Includes pocket style drop down step at left rear staircase. The rear access doors to match the rear body finish.
Body aerial 95/CR100 CII/Quest medium cab without pump. 100" wide with Left extended rescue style high side, right half side with recessed area above for horizontal ladder storage and rear side staircases. 61" high body for 11'‐10" OAH.
Body aerial 95/CR100 CII/Quest long cab without pump. 100" wide with L and R extended rescue style high sides and rear side staircases. 61" high body for 11'‐10" OAH.
Tiller body ‐ without pump. Includes tractor body w/12" wide compts (140" WB w/58" cab), trailer body with raised compts (L2/R2‐
L6/R6), 50" wide ladder tunnel, tool compartment at rear of body below ladder tunnel and staircases with pocket style flop down steps each side of tractor body.
$71,243.00
3080‐0057
3080‐0059
3080‐0064
3080‐0065
3080‐0066
3080‐0067
3080‐0069
3080‐0070
3080‐0071
3080‐0072
$60,392.00
$61,219.00
$50,973.00
$74,513.00
$48,405.00
$52,324.00
$51,964.00
$64,349.00
$60,392.00
$69,118.00
Option No.
3080‐0073
3080‐0074
3080‐0075
3080‐0079
3080‐0080
3080‐0087
3080‐0096
3080‐0097
3080‐0098
3080‐0100
3080‐0113
3080‐0114
3080‐0115
3080‐0116
3080‐0117
3080‐0118
Description
Body aerial HP100 CII without pump. 100" wide tandem axle. (230" WB medium cab). Includes L and R extended rescue style high sides and double beavertails.
Body aerial HP100 Platform 250" WB 67.5/68 cab without pump. 100" wide with L and R extended rescue style high sides, seperate rear side compartments (tall compartment to be ahead of outrigger) and rear side staircases. The door on small compt to rear of rear outrigger to match wheelwell.
Tiller body ‐ without pump. Includes tractor body w/22"w compts (150" WB w/58" cab), raised trailer body (L2/L3/L4/L5/L6, R2/R3/R4/R5/R6, 50" wide ladder tunnel, tool compartment at rear of body below ladder tunnel and staircases with pocket style flop down steps each side of tractor body.
Body aerial HP100 Platform 250" WB 68 cab without pump. 100" wide with L and R extended rescue style high sides, 3/16" smooth plate floors, seperate rear side compartments (tall compartment to be ahead of outrigger) and rear side staircases. The door on small compt to rear of rear outrigger to match wheelwell.
Body aerial HM100/110 CII without pump. 96" wide with L and R ladder recesses, 16 wide forward upper compt (IPO trans), (3) upper storage compartments (two trans),and double beavertails. Manual cab tilt pump located low in R1 against forward wall. 61.25" high body for low OAH. Requires troughed cab.
Body aerial HM100/110 CII without pump. 96" wide with L and R ladder recesses, 20 wide forward upper compt (IPO trans), (3) upper storage compartments (two trans), and double beavertails. Manual cab tilt pump located low in R1 against forward wall. 61.25" high body for low OAH. Requires troughed cab.
Body aerial HP100 Platform 250" WB 67.5/68 cab without pump. 100" wide with L and R extended rescue style high sides, seperate rear side compartments (tall compartment to be rearward of outrigger) and rear side staircases. The door on small compt next to rear outrigger to match wheelwell.
HP95 MidMount front body without pump. Includes a compt on each side ahead of waterway inlet with a vert hinged double pan painted door.
HP95 MidMount rear body with wide ladder tunnel and no hosebed or staircase.
Body aerial 95/CR100 CII extended aerial cab without pump (245" WB). 100" wide with L and R extended rescue style high sides and rear side staircases. 58" high body for 11'‐7" +or‐1" OAH. Requires troughed cab.
Full height rear body compartment (B1). Includes satin roll‐up door with header and upper area for mounting of traffic advisor (not included).
Full height rear body compartment (B1). Includes satin roll‐up door with header, lower floor mounting and plumbing routing for reel application and upper area for mounting of traffic advisor (not included).
Full height rear body compartment (B1). Includes satin roll‐up door with header, upper area for mounting of traffic advisor (not included) and rear lower wall access to fuel tank sender.
Full height rear body compartment (B1). Includes satin roll‐up door with header, lower floor mounting and plumbing routing for reel application, upper area for mounting of traffic advisor (not included) and rear lower wall access to fuel tank sender.
Body mainframe and forward compartment extrusions and headboard (90" high body) for use with roll‐up doors.
Body mainframe and forward compartment extrusions and headboard (90" high body) for use with roll‐up doors.
PRICE
$65,808.00
$59,786.00
$70,331.00
$61,289.00
$72,957.00
$72,957.00
$59,786.00
$23,948.00
$27,219.00
$64,988.00
$0.00
$0.00
$0.00
$0.00
$0.00
$0.00
Option No.
3080‐0119
3080‐0120
3080‐0121
3080‐0122
3080‐0127
3080‐0128
3080‐0133
3080‐0134
3080‐0135
3080‐0136
3080‐0143
3080‐0144
3080‐0145
3080‐0146
3080‐0148
3080‐0149
Description
Rearward compartment extrusions and enhanced extended rear body assembly with smooth plate panels (driver side upper and lower and officer side lower with upper storage tunnel door). Includes mounting areas for DOTand NFPA lighting, driver side rear NFPA steps and handrails (4).
Rearward compartment extrusions and enhanced extended rear body assembly with smooth plate panels (driver side lower with upper storage tunnel door and officer side lower with upper storage tunnel door). Includes mounting areas for DOTand NFPA lighting, driver side rear NFPA steps and handrails (4).
Rearward compartment extrusions and enhanced extended rear body assembly with smooth plate panels (driver side upper and lower and officer side lower with upper storage tunnel door). Includes mounting areas for DOTand NFPA lighting, (2) receptacle mounts and driver side rear NFPA steps and handrails (4).
Rearward compartment extrusions and enhanced extended rear body assembly with smooth plate panels (driver side lower with upper storage tunnel door and officer side lower with upper storage tunnel door). Includes mounting areas for DOTand NFPA lighting, (2) receptacle mounts and driver side rear NFPA steps and handrails (4).
Body mainframe and forward compartment extrusions and headboard (90" high body) for use with hinged doors.
Body mainframe and forward compartment extrusions and headboard (90" high body) for use with hinged doors.
Rearward compartment extrusions and enhanced extended rear body assembly with smooth plate panels (driver side upper and lower and officer side lower with upper storage tunnel door). Includes mounting areas for DOTand NFPA lighting, driver side rear NFPA dual lighted LED steps and (4) handrails.
Rearward compartment extrusions and enhanced extended rear body assembly with smooth plate panels (driver side lower with upper storage tunnel door and officer side lower with upper storage tunnel door). Includes mounting areas for DOTand NFPA lighting, driver side rear NFPA dual lighted LED steps and (4) handrails.
Rearward compartment extrusions and enhanced extended rear body assembly with smooth plate panels (driver side upper and lower and officer side lower with upper storage tunnel door). Includes mounting areas for DOTand NFPA lighting, (2) receptacle mounts and driver side rear NFPA dual lighted LED steps and (4) handrails.
Rearward compartment extrusions and enhanced extended rear body assembly with smooth plate panels (driver side lower with upper storage tunnel door and officer side lower with upper storage tunnel door). Includes mounting areas for DOTand NFPA lighting, (2) receptacle mounts and driver side rear NFPA dual lighted LED steps and (4) handrails.
Body aerial HM100/110 ladder without pump (172 C/A for use with DPF/SCR aftertreatment). 100" wide with L and R extended rescue style high sides and double beavertails. 67" high body for 11'‐5" OAH.
Body aerial HP100 ladder without pump (172 C/A for use with DPF/SCR aftertreatment). 100" wide tandem axle. (230" WB medium cab / 240" WB long cab). Includes L and R extended rescue style high sides and double beavertails.
Body aerial 95/CR100 medium cab without pump (187 C/A for use with DPF/SCR aftertreatment). 100" wide with L and R extended rescue style high sides and rear side staircases. 61" high body for 11'‐10" OAH.
Body aerial HP100 Platform without pump (192 C/A for use with DPF/SCR aftertreatment). 100" wide with L and R extended rescue style high sides, seperate rear side compartments and rear side staircases. The door on small compt next to rear outrigger to match wheelwell.
HP95 MidMount front body without pump (for use with DPF / SCR aftertreatment).
HP95 MidMount front body without pump low travel height (for use with DPF / SCR aftertreatment).
PRICE
$0.00
$0.00
$0.00
$0.00
$0.00
$0.00
$0.00
$0.00
$0.00
$0.00
$61,683.00
$63,292.00
$60,392.00
$60,392.00
$21,879.00
$20,847.00
Option No.
3080‐0150
3080‐0151
3080‐0152
3080‐0154
3080‐0155
3080‐0156
3080‐0157
3080‐0158
3080‐0159
3080‐0160
3080‐0161
3080‐0162
3080‐0163
3080‐0164
3080‐0165
Description
Body aerial HP75/78 with combined standard height front side compts and center hose bed. Configured for midship pump and 400‐500 tank. Single axle 100'' wide body.
Body aerial 95/CR100 CII/Quest long cab without pump (177 C/A for use with DPF/SCR aftertreatment). 100" wide with L and R extended rescue style high sides and rear side staircases. 61" high body for 11'‐10" OAH.
Body aerial HP100 Platform without pump. 100" wide with L and R extended rescue style high sides, separate rear side compartments and rear side staircase (left side only). The door on small compt next to rear outrigger to match wheel well.
Body aerial 95/CR100 with center hose bed. Configured for 250" wheel base, long cab, midship pump and 300 tank. 100" wide with L and R extended rescue style high sides and double beavertails.
Body aerial HP100 with center hose bed. Configured for midship pump and 500 tank. 100" wide body with 230" wheelbase tandem axle. Includes L and R extended rescue style high sides and single access staircase at center rear of body. The rear turntable access door to match the rear body finish.
SS body with lowered aerial HP100 Platform, fire pump without tank/hose bed (body lowered 2"). 100" wide with L and R extended rescue style high sides, combined rear side compartments and rear side staircases. The doors on small compts next to rear outriggers to be drop‐down stainless steel.
Body aerial HP100 Platform without pump. 100" wide with L and R extended rescue style high sides, combined rear side compartments and rear side staircases. The doors on small compts next to rear outrigger to match wheelwell.
Body aerial HM100/110 without pump, 230" wheelbase with medium cab. 100" wide with L and R extended rescue style high sides, L1 hydraulic oil reservior location and double beavertails. 61" high body for low OAH. Requires troughed cab.
Body aerial HM100/110 without pump, 220" wheelbase with medium cab. 100" wide with L and R extended rescue style high sides, L1 hydraulic oil reservior location and double beavertails. 61" high body for 10'‐11" (+or‐1") OAH. Requires troughed cab.
Rearward compartment extrusions and enhanced extended rear body assembly with smooth plate panels (driver side lower with upper storage tunnel door and officer side lower with upper storage tunnel door). Includes mounting areas for DOTand NFPA lighting, driver side rear NFPA dual lighted LED steps and (4) handrails. The driver side upper rear panel area to include area for routing of a 3" rear discharge IPOS.
Body aerial Bronto RLP. Includes deep upper right side compartment, short hosebed, 3/16" smooth plate floors and pocket style flop down steps at each staircase. The doors on compts next to fwd outriggers to match the outrigger covers. The doors on small compts over forward tandem wheel to match wheelwell. The doors at rear of body on the lower aerial control panel compt to match rear body finish.
Body aerial HM100/110 without pump, 220" wheelbase with medium cab. 100" wide with L and R extended rescue style high sides, L1 hydraulic oil reservoir location and double beavertails. 64" high body for 11'‐3" OAH. Requires troughed cab (if applicable).
Body aerial HM100/110 without pump, 220" wheelbase with medium cab. 100" wide with L and R extended rescue style high sides, L1 hydraulic oil reservoir location and double beavertails. 67" high body for 11'‐5" OAH.
Body aerial HP75 / HP78 SideStacker Quest / CII / Typhoon with pump. Single axle. 65" body height for low OAH applications. Includes extended R1 compt and pocket style drop down step at left rear staircase. The rear access doors to match the rear body finish.
Stainless steel body aerial HP75 / HP78 with center hose bed. Configured for midship pump and 400 tank. Single axle 100" wide body. Includes L and R rescue style high sides. The rear turntable access door to match the rear body finish.
PRICE
$48,415.00
$60,392.00
$60,392.00
$71,243.00
$74,266.00
$79,841.00
$60,392.00
$68,005.00
$68,005.00
$0.00
$56,557.00
$68,005.00
$60,534.00
$50,973.00
$53,951.00
Option No.
3080‐0166
3080‐0167
3080‐0168
3080‐0169
3080‐0170
3080‐0171
3080‐0172
3080‐0173
3080‐0174
3080‐0175
3080‐0176
3080‐0177
3080‐0182
Description
Stainless steel body aerial HP75 / HP78 SideStacker Quest / CII / Typhoon with pump. Single axle. Includes pocket style drop down step at left rear staircase. Includes full length of body right side hose bed. The rear access doors to match the rear body finish.
Stainless steel body aerial HP75 / HP78 SideStacker Quest / CII / Typhoon with pump. Single axle. Includes full height R1 compartment and pocket‐style drop‐down step at the left rear staircase, and a shortened hose bed length. The rear access doors to match the rear panel body finish.
Stainless Steel Body aerial HP75 / HP78 with center hose bed. Configured for midship pump and 400 gal tank. Single axle 100" wide body. Includes L and R rescue style extended high sides. The rear turntable access door to match the rear body finish.
Stainless steel Body aerial HP75 / HP78 with combined extended height front side compts, beavertail compts combined w/rear side compts and center hose bed. Configured for midship pump and 400 gal tank. Single axle 100'' wide body. The rear turntable access door to match the rear body finish.
Stainless Steel Body aerial HP75 / HP78 SideStacker Quest / CII / Typhoon with pump. Single axle. Right side ahead of rear axle to have two separate compts, 24"w R1 and 32"w R2. Includes pocket style drop down step at left rear staircase. The rear access doors to match the rear body finish.
Stainless Steel Body aerial HP75 with combined standard height front side compts and center hose bed. Configured for midship pump and 400 gal tank. Single axle 100'' wide body.
Stainless Steel Body aerial HP75 / HP78 SideStacker Quest / CII / Typhoon with pump. Single axle. 65" body height for low OAH applications. Includes extended R1 compt and pocket style drop down step at left rear staircase. The rear access doors to match the rear body finish.
Body aerial 95/CR100/137 CII/Quest long cab without pump (177.5 C/A for use with DPF/SCR after treatment). 96" wide body. Left side to include extended rescue style high side L1/L2, recessed area for horizontal ladder storage and additional compartment to rear of ladders. Right side to be extended rescue style high side. Body includes upper transverse storage in L2/R2 upper, 3/16" upper body plate work, rear of body raised 4" aft of rear jack legs and rear side staircases. 61" high body for 11'‐10" +or‐1" OAH.
Body aerial HP100 Platform without pump. 100" wide with L and R extended rescue style high sides, seperate rear side compartments and rear side staircases. Rear of body raised 4" for improved angle of departure. The door on small compt next to rear outrigger to match wheelwell.
Body aerial 95/CR100 medium cab without pump (187 C/A for use with DPF/SCR aftertreatment). 100" wide with L and R extended rescue style high sides and rear side staircases. 58" high body for 11'‐7" +or‐1" OAH. Requires troughed cab.
Body aerial HP100 ladder without pump (172 C/A for use with DPF/SCR aftertreatment). 100" wide tandem axle. (230" WB medium cab / 240" WB long cab). Includes L and R extended rescue style high sides, provisions for L1 hydraulic reservoir and double beavertails.
Diamond plate body for use with narrow water tank, single axle chassis and driver side frame mounted pump. Includes driver and officer side forward lower body compartments (drivers narrow), framed wheel well area with diamond plate corners and flat back style rearend with 12" tailboard.
Diamond plate body for use with narrow water tank, tandem axle chassis and individual SM pump module. Includes driver and officer side forward lower body compartments, framed wheel well area with diamond plate corners and flat back style rearend with 12" tailboard.
PRICE
$59,987.00
$59,987.00
$56,149.00
$60,697.00
$60,277.00
$56,162.00
$57,797.00
$65,265.00
$60,392.00
$64,988.00
$63,292.00
$10,843.00
$12,542.00
Option No.
3080‐0183
3080‐0184
3080‐0186
3080‐0187
3080‐0188
3080‐0195
3080‐0196
3080‐0197
3080‐0198
3080‐0199
3080‐0200
3080‐0201
3080‐0202
3080‐0204
3080‐0207
3080‐0214
3080‐0215
Description
Diamond plate body for use with wide water tank, single axle chassis and individual SM pump module. Includes driver and officer side forward lower body compartments, framed wheel well area with diamond plate corners and flat back style rearend with 12" tailboard.
Diamond plate body for use with wide water tank, tandem axle chassis and driver side frame mounted pump. Includes driver and officer side forward lower body compartments (drivers narrow), framed wheel well area with diamond plate corners and flat back style rearend with 12" tailboard.
Diamond plate body for use with wide water tank, tandem axle chassis and individual SM pump module. Includes driver and officer side forward lower body compartments, framed wheel well area with diamond plate corners and flat back style rearend with 12" tailboard.
Smooth plate painted body for use with wide water tank, tandem axle chassis with driver side under mount pump and officer side forward discharge/intake panel. Includes driver and officer side forward and rearward lower body compartments, framed wheel well area with smooth plate corners and flat back style rearend with 12" tailboard.
HP95 MidMount center body without crosslays includes tank, 3/16" smooth plate compartment floors and wide ladder tunnel.
HP95 MidMount front body with pump and 3/16" smooth plate compartment floors (for use with DPF / SCR aftertreatment).
HP95 MidMount rear body with 3/16" smooth plate compartment floors, wide ladder tunnel and no hosebed or staircase.
HP95 MidMount front body with pump and 3/16" smooth plate compartment floors.
Body aerial HP75 / HP78 SideStacker Quest / CII / Typhoon with pump. Single axle. Includes 3/16" diamond plate floors for all compartments, pocket style drop down step at left rear staircase. The rear access doors to match the rear body finish.
Body aerial 95/CR100 CII/Quest medium cab without pump (187 C/A for use with DPF/SCR aftertreatment). 100" wide with L and R extended rescue style high sides and double beavertails. 63" high body for 12'‐1" OAH.
Body aerial HP100 Platform 260" WB 80" cab without pump (180 C/A for use with DPF/SCR aftertreatment). 100" wide with L and R extended rescue style high sides, separate rear side compartments and rear side staircases. The door on small compt next to rear outrigger to match wheelwell.
Body aerial 95/CR100 medium cab without pump (187 C/A for use with DPF/SCR aftertreatment). 100" wide with L and R extended rescue style high sides and rear side staircases. Includes rear perimeter of body aft of rear jack legs raised 4" to improve angle of departure. 61" high body for 11'‐10" OAH.
Body aerial HM100/110 ladder without pump (172 C/A for use with DPF/SCR aftertreatment). 100" wide with L and R extended rescue style high sides and double beavertails. 64" high body for 11'‐2" +/‐1" OAH. Requires troughed cab (if applicable).
Body aerial single axle LTH100 without pump (162 C/A for use with vertical SCR aftertreatment). 96" wide with L and R rescue style high sides and rear side staircases. Rear of body aft of rear jack legs raised 3". 61" high body. (10'‐7" OAH with no wway, 10'10" OAH with wway).
Low profile cab stainless steel body aerial HP75 / HP78 SideStacker Quest / CII / Typhoon with pump, body lowered by 4" to 65" high. Single axle. Includes pocket style drop down step at left rear staircase. Includes full length of body right side hose bed. The rear access doors to match the rear body finish.
Anodes for water tank ‐ (3) anodes located in bottom of water tank.
Body aerial HP75 / HP78 SideStacker Quest / CII / Typhoon with pump for industrial applications. Single axle. Includes extended R1 compt and pocket style drop down step at left rear staircase. The rear access door to match the rear body finish.
PRICE
$10,734.00
$11,623.00
$11,955.00
$14,482.00
$20,074.00
$22,174.00
$32,852.00
$22,174.00
$51,198.00
$60,392.00
$59,786.00
$60,392.00
$68,005.00
$61,683.00
$59,987.00
$524.00
$50,973.00
Option No.
3080‐0216
3080‐0217
3080‐0218
3080‐0219
3080‐0220
3080‐0224
3080‐0227
3080‐0228
3080‐0229
3080‐0230
3080‐0231
3080‐0232
3080‐0234
Description
Body aerial HM100/110 CII/Quest long cab ladder without pump (162.5" C/A for use with DPF/SCR aftertreatment). 100" wide with L and R extended rescue style high sides, L1 hydraulic oil reservoir and double beavertails. 64" high body for 11'‐2" +/‐1" OAH. Requires troughed cab (if applicable).
Body aerial HP100 ladder without pump (172 C/A for use with DPF/SCR aftertreatment). 100" wide tandem axle. (230" WB medium cab / 240" WB long cab). Includes L and R extended rescue style high sides, provisions for L1 hydraulic reservoir and double beavertails. 61" high body for low OAH. Requires troughed cab.
Body aerial HP100 ladder without pump (172 C/A for use with DPF/SCR aftertreatment). 100" wide tandem axle. (230" WB medium cab / 240" WB long cab). Includes L and R extended rescue style high sides and dual rear side staircases. 64" high body for 11'‐9" OAH.
Body aerial single axle LTH100 without pump (162 C/A for use with vertical SCR aftertreatment). 100" wide with L and R rescue style extended high sides and rear side staircases. Rear of body aft of rear jack legs raised 3". 61" high body. (10'‐7" OAH with no wway, 10'10" OAH with wway).
Body eMAX aerial HP75/78 with combined standard height front side compts and center hose bed. Configured for midship pump and 400‐500 tank. Single axle 100" wide body.
Body aerial HM100/110 ladder without pump (172 C/A for use with DPF/SCR aftertreatment). 100" wide with L and R extended rescue style high sides and dual rear side staircases. 67" high body for 11'‐5" OAH.
Body aerial HP100 Platform 250" WB 67.5/68 cab without pump (182" C/A for use with DPF/SCR aftertreatment). 100" wide with L and R extended rescue style high sides, seperate rear side compartments, upper 70" wide open storage beneath aerial and rear side staircases. Rear of body raised 4" for improved angle of departure. The doors on small compts next to rear outrigger to match wheelwell.
Body aerial HP75/78 SideStacker CII with pump. Single axle. 62" body height for low OAH applications. Includes pocket style drop down step at left rear staircase. The rear access doors to match the rear body finish.
Body aerial HP100 with 3" lower center hose bed body. Configured for midship pump and 450 tank. 100" wide body with 230" wheelbase tandem axle. Includes L and R extended rescue style high sides and double beavertails.
Body aerial HP100 Platform 250" WB 67.5/68 cab without pump (182" C/A for use with DPF/SCR aftertreatment). 100" wide with L and R extended rescue style high sides, compartments L2/R2 divided into upper and lower compartments(L2 lower 25" high opening/R2 lower 28" high opening), seperate rear side compartments, upper 70" wide open storage beneath aerial and rear side staircases. Rear of body raised 4" for improved angle of departure. The doors on small compts next to rear outrigger to match wheelwell.
Body aerial 95/CR100 medium cab without pump (187 C/A for use with DPF/SCR aftertreatment). 100" wide with L and R extended rescue style high sides and rear side staircases. 58" high body for 11'‐7" +or‐1" OAH. Requires troughed cab.
Body aerial HP100 ladder without pump (172 C/A for use with DPF/SCR aftertreatment). 100" wide tandem axle. (230" WB medium cab / 240" WB long cab). Includes L and R extended rescue style high sides, center front of body mounted aerial hydraulic reservoir and double beavertails. 61" high body for low OAH. Requires troughed cab.
Body aerial HP75 / HP78 with combined standard height front side compts, beavertail compts combined w/rear side compts and center hose bed. Configured for midship pump and 400‐500 tank. Single axle 100" wide body. The rear turntable access door to match the rear body finish.
PRICE
$68,005.00
$67,686.00
$63,840.00
$63,880.00
$48,415.00
$63,880.00
$61,983.00
$50,973.00
$75,263.00
$61,983.00
$64,988.00
$67,686.00
$48,645.00
Option No.
3080‐0235
3080‐0238
3080‐0241
3080‐0247
3080‐0248
3080‐0249
3080‐0250
3080‐0251
3080‐0252
3080‐0253
3080‐0254
3080‐0255
Description
Body aerial HP75 / HP78 SideStacker Quest / CII / Typhoon with pump for industrial applications. Single axle. Includes pocket style drop down step at left rear staircase. The rear access door(s) to match the rear body finish.
Body aerial HP100 Platform without pump (192 C/A for use with DPF/SCR after treatment). 100" wide with L and R extended rescue style high sides, left side combined rear compartment with rear side staircase, right side rear compartment IPO rear side staircase . The doors on small compartments next to rear outriggers to match wheel well.
Body aerial HP100 ladder 240" WB 80" cab without pump (160 C/A for use with DPF/SCR aftertreatment). 100" wide with L and R extended rescue style high sides, extra deep open storage beneath aerial and double beavertails.
Body aerial 95/CR100 with center hose bed for 250" W/B. Configured for midship pump and 300 tank (192 C/A for use with DPF/SCR aftertreatment). 100" wide with L and R extended rescue style high sides, and double beavertails. 63" high body for 12'‐1" OAH.
Body aerial HPS105 with center hose bed. Configured for midship pump and 300 tank (182 C/A). 100" wide with L and R extended rescue style high sides, double beavertails and raised rear body for improved angle of departure.
Body aerial HPS105 without pump (182 C/A for use with DPF/SCR aftertreatment). 100" wide with L and R extended rescue style high sides, rear side staircases and raised rear body for improved angle of departure.
Body aerial single axle LTH100 without pump (162 C/A for use with vertical SCR aftertreatment). 96" wide with L and R rescue style high sides, combined rear side compartments and an independent rear staircase module to rear of main body with Zico swing out and down access ladders, one each side. Rear staircase module rear corners pinched in for better turning clearance and raised 3" for improved angle of departure. 61" high body. (10'‐7" OAH with no wway, 10'10" OAH with wway).
Body aerial HP100 Platform (lowered 2") with hydraulic driven water pump and 200 gallon tank (192 C/A for use with DPF/SCR after treatment). 100" wide with L and R extended rescue style high sides, left side combined rear compartment, left rear side staircase, right side rear compartment IPO right rear side staircase and rear of body raised 4" for improved angle of departure. The doors on small compartments next to rear outriggers to match wheel well.
Body aerial HM100/110/LTH100 with center hose bed. Configured for midship pump and 450 tank. 100" wide with L and R extended rescue style high sides and double beavertails. 64" high body. Requires troughed cab.
Body aerial HM100/110 with center hose bed. Configured for midship pump and 450 tank. 100" wide with L and R extended rescue style high sides, right side hose hose chute only and rear side facing dual staircases . 64" high body for 11'‐4" OAH. Requires troughed cab.
Body aerial HP100 Platform (lowered 1") 260"WB 67.5/68 cab without pump (192.5 C/A for use with DPF/SCR after treatment). 100" wide body, L2/R2 transverse and dual rear side staircases. Left side to include recessed area for horizontal ladder storage. Right side to include extended rescue style high sides, combined rear side compartment. The door on small compts next to rear outrigger to match wheel well.
Body aerial HP75 / HP78 with combined extended height front side compartment on driver side and separate extended height front side compartments (R1‐36"W / R2 22"W) on officer side, enhanced extended combined rear beavertail compts and center hose bed. Configured for midship pump and 400‐500 tank. Single axle 100'' wide body. Includes driver and officer side ladder tunnels and hose chutes extended rearward flush with rear of body with standard center style turntable access staircase. The rear turntable access door to match the rear body finish.
PRICE
$50,973.00
$60,392.00
$62,756.00
$74,278.00
$71,243.00
$60,392.00
$67,738.00
$62,535.00
$72,475.00
$74,618.00
$65,265.00
$56,725.00
Option No.
3080‐0256
3080‐0259
3080‐0262
3080‐0263
3080‐0265
3080‐0267
3080‐0268
3080‐0269
3080‐0273
3080‐0274
3080‐0276
Description
Body aerial 95/CR100 with center hose bed. Configured for 240" WB, medium cab, midship pump w/42" PPNL and 300 tank. 100" wide with L and R extended rescue style high sides and double beavertails. 63" high body for 12'‐1" OAH
Body aerial Bronto Industrial RLP. Includes pump module, full length hosebed and pocket style flop down steps at each staircase. The doors on compts next to fwd outriggers to match the outrigger covers. The doors on small compts over forward tandem wheel to match wheelwell. The doors at rear of body on the lower aerial control panel compt to match rear body finish.
Body aerial HM100/110/LTH100 without pump (162 C/A for use with DPF/SCR aftertreatment), 230" wheelbase, tandem axle with long cab. 100" wide with L and R extended rescue style high sides and dual rear side staircases. 61" high body for low OAH. Requires troughed cab.
Body aerial 95/CR100/CR137 with center hose bed. Configured for 250" wheel base, long cab, midship pump and 300 gallon tall tank. 100" wide with L and R extended rescue style high sides and double beavertails. Note hose chutes modified on driver and officer sides to allow 5" LDH hose to pass thru due to 5" lower aerial/body. 58" high body for 11'‐7" +or‐ 1" OAH. Requires troughed cab.
Body aerial HP100 Platform without pump with 260" W/B and 80" cab (180" C/A for use with DPF/SCR aftertreatment). 100" wide with L and R extended rescue style high sides, seperate rear side compartments and rear side staircase (left side only). The door on small compt next to rear outrigger to match wheelwell.
Body aerial 95/CR100 CII/Quest long cab without pump. 250"W/B (182 C/A for use with DPF/SCR aftertreatment). 100" wide with L and R extended rescue style high sides and rear side staircases. 61" high body for 11'‐10" OAH.
Body aerial RLP without pump. Includes dual rear side staircases with pocket style flop down steps at each staircase. The doors on compts next to fwd outriggers to match the outrigger covers. The doors on small compts over forward tandem wheel to match wheelwell. The doors at rear of body on the lower aerial control panel compt to match rear body finish.
Body aerial single axle LTH100 without pump for use with a medium cab (162 C/A for use with vertical SCR aftertreatment). 96" wide, R1 rescue style high side with L and R half sides with recess above for horizontal ladder storage. Upper body storage compartments for storage beneath aerial, (1) one left side forward compartment, (1) one transverse compartment and (2) two rearward compartments with open storage between. Dual rear side staircases includes 1" flex joint separating it from the main body, rear corners pinched in for better turning clearance and raised 3" for improved angle of departure. 61" high body. (10'‐7" OAH with no wway, 10'10" OAH with wway).
Body aerial HP100 with center hose bed. Configured for midship pump and 500 tank. 100" wide body with (230" wheelbase medium cab/240" wheelbase long cab) tandem axle. Includes L and R extended rescue style high sides and double beavertails. Extended high only will be raised 3" for increased hosebed.
Body aerial HP100 ladder without pump (172 C/A for use with DPF/SCR aftertreatment). 100" wide tandem axle with L1 extended rescue style high side and R1 extended rescue style high side with half right side for recessed ladder storage above tandem axle. (230" WB medium cab / 240" WB long cab). Includes provisions for L1 hydraulic reservoir and double beavertails.
Body eMAX aerial HP75/78 with combined standard height front side compts, a deep upper L1, one large compartment over driver side rear wheel, enhanced extended beavertail compartments combined with rear side compartments and center hose bed. Configured for midship pump and 400‐500 tank. Single axle 100" wide body.
PRICE
$71,243.00
$59,568.00
$70,580.00
$77,397.00
$60,392.00
$60,392.00
$54,893.00
$65,425.00
$73,512.00
$65,198.00
$57,985.00
Option No.
3080‐0277
3080‐0278
3080‐0279
3080‐0280
3080‐0281
3080‐0282
3080‐0283
3080‐0288
3080‐0289
3080‐0290
3080‐0291
3080‐0292
3080‐0293
Description
Body aerial HP100 Platform 260"WB 58 med cab without pump (202" C/A for use with DPF/SCR after treatment). 100" wide body, L2/R2 transverse and dual rear side staircases. Right side to include recessed area for horizontal ladder storage. Left side to include extended rescue style high sides, combined rear side compartment. The door on small compts next to rear outrigger to match wheel well.
Tiller body without pump. Includes tall rescue style L6/R6 to match forward compartments, tool compartment at rear of body below ladder tunnel and staircases with pocket style flop down steps each side of tractor body.
Body aerial HP100 Platform 260" WB 80" cab without pump (180 C/A for use with DPF/SCR aftertreatment). 100" wide with L and R extended rescue style high sides, L2/R2 upper transverse compartment, separate rear side compartments, upper 70" wide open storage beneath aerial and No rear side staircases. Note rear turntable access shall be a Zico swing‐out and down ladder mounted on rear of body, driver side. The door on small compt next to rear outrigger to match wheelwell.
Body aerial HP75/78 SideStacker Quest / CII / Typhoon with pump. Tandem axle. Includes extended R1 compt, optional R2 compartment over rear wheel and pocket style drop down step at left rear staircase. The rear access doors to match the rear body finish.
A 2.5" FNPT coupling weld to front of the tank to allow for a tank fill connection. Water Master.
Body aerial HP75 / HP78 SideStacker Quest / CII / Typhoon with pump. Single axle. Includes extended R1 compt, notched R1 for vertical exhaust and pocket style drop down step at left rear staircase. The rear access doors to match the rear body finish.
Body aerial HP75 / HP78 SideStacker Quest / CII / Typhoon with pump. Single axle. Includes driver and officer side dual (22/40) rescue style extended height compartments ahead of wheel well, 6" stretch thru L5/R3 and pocket style drop down step at left rear staircase. The rear access doors to match the rear body finish.
304L Stainless Steel formed body for 2000gal Wetside tanker, single axle chassis, single rear dump, pump module forward of body. Includes driver and officer side low‐side body compartments, painted FRP wheel well area and flat back style rearend with 12" tailboard.
304L Stainless Steel formed body for 2000gal Wetside tanker, single axle chassis, triple dumps at rear of body, pump module forward of body. Includes driver and officer side low‐side body compartments, painted FRP wheel well area and flat back style rearend with 12" tailboard.
304L Stainless Steel formed body for 2000gal Wetside water tanker, single axle chassis, single rear dump, driver side under tank pump. Includes driver and officer side low‐side body compartments, FRP wheel well area and flat back style rearend with 12" tailboard.
304L Stainless Steel formed body for 2000gal Wetside water tanker, single axle chassis, triple dumps at rear of body, driver side under tank pump. Includes driver and officer side low‐side body compartments, FRP wheel well area and flat back style rearend with 12" tailboard.
304L Stainless Steel formed body for 2500/3000gal Wetside water tanker, tandem axle chassis, single rear dump, pump module forward of body. Includes driver and officer side low‐side body compartments, FRP wheel well area and flat back style rearend with 12" tailboard.
304L Stainless Steel formed body for 2500/3000gal Wetside water tanker, tandem axle chassis, triple dumps centered in wheel well, pump module forward of body. Includes driver and officer side low‐side body compartments, FRP wheel well area and flat back style rearend with 12" tailboard.
PRICE
$65,265.00
$66,086.00
$63,391.00
$58,309.00
$300.00
$52,473.00
$53,973.00
$14,800.00
$15,800.00
$14,800.00
$15,900.00
$17,700.00
$18,700.00
Option No.
3080‐0294
3080‐0295
3080‐0296
3080‐0297
3080‐0298
3080‐0299
3080‐0300
3080‐0302
3090‐0000
3090‐0019
3090‐0021
3090‐0032
3090‐0033
3090‐0036
3090‐0039
3092‐0102
3100‐0000
Description
304L Stainless Steel formed body for 2500/3000gal Wetside water tanker, tandem axle chassis, single rear dump, driver side undertank pump. Includes driver and officer side low‐side body compartments, FRP wheel well area and flat back style rearend with 12" tailboard.
304L Stainless Steel formed body for 2500/3000gal Wetside water tanker, tandem axle chassis, triple dumps centered in wheel well, driver side undertank pump. Includes driver and officer side low‐side body compartments, FRP wheel well area and flat back style rearend with 12" tailboard.
304L Stainless Steel formed body for 3500/4000gal Wetside water tanker, tandem axle chassis, single rear dump, pump module forward of body. Includes driver and officer side low‐side body compartments, FRP wheel well area and flat back style rearend with 12" tailboard.
304L Stainless Steel formed body for 3500/4000gal Wetside water tanker, tandem axle chassis, triple dumps centered in wheel well, pump module forward of body. Includes driver and officer side low‐side body compartments, FRP wheel well area and flat back style rearend with 12" tailboard.
304L Stainless Steel formed body for 3500/4000gal Wetside water tanker, tandem axle chassis, single rear dump, driver side undertank pump. Includes driver and officer side low‐side body compartments, FRP wheel well area and flat back style rearend with 12" tailboard.
304L Stainless Steel formed body for 3500/4000gal Wetside water tanker, tandem axle chassis, triple dumps centered in wheel well, driver side undertank pump. Includes driver and officer side low‐side body compartments, FRP wheel well area and flat back style rearend with 12" tailboard.
Body aerial HP75 / HP78 with center hose bed. Configured for midship pump and 400‐500 tank. Single axle 100'' wide body. Includes L and R rescue style high sides with enhanced extended combined rear beavertail compts. The driver and officer side ladder tunnels and hose chutes extended rearward flush with rear of body with standard center style turntable access staircase. The rear turntable access door to match the rear body finish.
SS Body aerial HM100/110 ladder without pump. 100" wide with driver's extended rescue style high side, officer's horizontal ladder storage above right side compartments rear of full height R1,R2, R3. (1) driver side of body rear staircase.
Body Specs ‐ SideStacker aerial with tandem axle. Includes left rear staircase with pocket style drop down step.
Body Specs ‐ SideStacker aerial with tandem axle. Includes left rear staircase with pocket style drop down step and 3/16" smooth plate compartment floors.
Body Specs ‐ Aerial with tandem axle. Includes dual rear staircases with pocket style drop down steps.
Body Specs ‐ SideStacker eMAX aerial with tandem axle. Includes left rear staircase with pocket style drop down step.
Body Specs ‐ Aerial with tandem axle. Includes left rear staircase with pocket style drop down step.
The unit has an bumper to bumper length restriction. The length is not to be exceeded. 40ft. 6in.
Body Specs ‐ SideStacker 4 jack aerial with single axle. Includes left rear staircase with pocket style drop down step.
Sloped compartment floor. Compartment floor to be overlayed with a smooth aluminum plate that is sloped aprox 2 inches downward from the door opening to back of compartment in [#LOC]. Construction to be 3/16 aluminum.
Driver side body with full height 24" wide forward and 36" wide rearward compartmentation. Includes (1) 56" wide compartment over the wheel well.
PRICE
$17,900.00
$18,900.00
$19,700.00
$20,700.00
$19,900.00
$20,900.00
$48,284.00
$69,154.00
$0.00
$1,428.00
$0.00
$0.00
$0.00
$0.00
$0.00
$125.00
$8,985.00
Option No.
3100‐0001
3100‐0002
3100‐0003
3100‐0004
3100‐0006
3100‐0007
3100‐0008
3100‐0009
3100‐0010
3100‐0011
3100‐0012
3100‐0013
3100‐0014
3100‐0015
3100‐0016
3100‐0017
3100‐0018
3100‐0019
Description
Driver side body with full height 30" wide forward and 36" wide rearward compartmentation. Includes (1) 56" wide compartment over the wheel well.
Driver side body with full height 36" wide forward and 36" wide rearward compartmentation. Includes (1) 56" wide compartment over the wheel well.
Driver side body with full height 42" wide forward and 42" wide rearward compartmentation. Includes (1) 56" wide compartment over the wheel well.
Driver side body with full height 48" wide forward and 48" wide rearward compartmentation. Includes (1) 56" wide compartment over the wheel well.
Driver side body with upper and lower compartmentation. Includes 24" wide forward and 36" wide rearward lower compartments and (3) opening upper compartments.
Driver side body with upper and lower compartmentation. Includes 30" wide forward and 36" wide rearward lower compartments and (3) opening upper compartments.
Driver side body with upper and lower compartmentation. Includes 36" wide forward and 36" wide rearward lower compartments and (3) opening upper compartments.
Driver side body with upper and lower compartmentation. Includes 42" wide forward and 42" wide rearward lower compartments and (3) opening upper compartments.
Driver side body with upper and lower compartmentation. Includes 48" wide forward and 48" wide rearward lower compartments and (3) opening upper compartments.
Driver side body with upper and lower compartmentation. Includes 42" wide forward and 42" wide rearward lower compartments, (3) opening upper compartments with portable water tank storage with access door at rear.
Driver side body with upper and lower compartmentation. Includes 48" wide forward and 48" wide rearward lower compartments, (3) opening upper compartments with portable water tank storage with access door at rear.
Driver side body with full height 24" wide forward and 50" wide rearward extended compartmentation. Includes (1) 56" wide compartment over the wheel well.
Driver side body with full height 30" wide forward and 50" wide rearward extended compartmentation. Includes (1) 56" wide compartment over the wheel well.
Driver side body with full height 36" wide forward and 50" wide rearward extended compartmentation. Includes (1) 56" wide compartment over the wheel well.
Driver side body with full height 42" wide forward and 56" wide rearward extended compartmentation. Includes (1) 56" wide compartment over the wheel well.
Driver side body with full height 48" wide forward and 62" wide rearward extended compartmentation. Includes (1) 56" wide compartment over the wheel well.
Driver side body with full height 24" wide forward and 50" wide rearward enhanced extended compartmentation. Includes (1) 56" wide compartment over the wheel well.
Driver side body with full height 30" wide forward and 50" wide rearward enhanced extended compartmentation. Includes (1) 56" wide compartment over the wheel well.
PRICE
$9,612.00
$10,297.00
$11,005.00
$11,773.00
$9,434.00
$10,061.00
$10,733.00
$11,454.00
$12,224.00
$11,796.00
$12,590.00
$9,612.00
$10,244.00
$10,912.00
$11,633.00
$12,403.00
$9,902.00
$10,529.00
Option No.
3100‐0020
3100‐0021
3100‐0022
3100‐0024
3100‐0025
3100‐0026
3100‐0049
3100‐0050
3100‐0051
3100‐0052
3100‐0053
3100‐0054
3100‐0055
3100‐0056
3100‐0057
3100‐0059
3100‐0060
3100‐0066
3100‐0067
Description
Driver side body with full height 36" wide forward and 50" wide rearward enhanced extended compartmentation. Includes (1) 56" wide compartment over the wheel well.
Driver side body with full height 42" wide forward and 56" wide rearward enhanced extended compartmentation. Includes (1) 56" wide compartment over the wheel well.
Driver side body with full height 48" wide forward and 62" wide rearward enhanced extended compartmentation. Includes (1) 56" wide compartment over the wheel well.
Driver side body with full height 36" wide forward and 36" wide rearward compartmentation. Includes (1) 56" wide compartment over the wheel well.
Driver side body with full height 42" wide forward and 42" wide rearward compartmentation. Includes (1) 56" wide compartment over the wheel well.
Driver side body with full height 48" wide forward and 48" wide rearward compartmentation. Includes (1) 56" wide compartment over the wheel well.
Driver side body with full height 24" wide forward and 36" wide rearward compartmentation. Includes (1) 56" wide compartment over the wheel well and 30 degree rear body angle for greater angle of departure.
Driver side body with full height 30" wide forward and 36" wide rearward compartmentation. Includes (1) 56" wide compartment over the wheel well and 30 degree angle of departure.
Driver side body with full height 36" wide forward and 36" wide rearward compartmentation. Includes (1) 56" wide compartment over the wheel well and 30 degree rear body angle for greater angle of departure.
Officer half side body with 24" wide forward and 36" wide rearward compartmentation. Includes adjustable ladder tracks and 30 degree rear body angle for greater angle of departure.
Officer half side body with 30" wide forward and 36" wide rearward compartmentation. Includes adjustable ladder tracks and 30 degree rear body angle for greater angle of departure.
Stainless steel driver side body with full height 36" wide forward and 48" wide rearward compartmentation (interior). Includes (1) 60" wide compartment over the wheel well.
Stainless steel driver side body with full height 48" wide forward and 48" wide rearward compartmentation (interior). Includes (1) 60" wide compartment over the wheel well.
Stainless steel driver side body with full height 60" wide forward and 60" wide rearward compartmentation (interior). Includes (1) 60" wide compartment over the wheel well.
Body mainframe and upper body/hosebed side assemblies for a 85" high body.
Stainless steel driver side body with full height 48" wide forward and 60" wide rearward compartmentation (interior). Includes (1) 60" wide compartment over the wheel well.
Stainless Steel officer half side body with 36" wide forward and 48" wide rearward compartmentation (interior). Includes adjustable ladder tracks.
Driver side body with full height 60" wide forward and 42" wide rearward compartmentation. Includes (1) 56" wide compartment over the wheel well.
Driver side body with upper and lower compartmentation. Includes 60" wide forward and 42" wide rearward lower compartments and (3) opening upper compartments.
PRICE
$11,200.00
$11,922.00
$12,690.00
$11,005.00
$11,773.00
$12,597.00
$9,332.00
$9,960.00
$10,631.00
$4,841.00
$4,841.00
$11,312.00
$12,951.00
$13,859.00
$0.00
$13,599.00
$5,660.00
$13,480.00
$13,078.00
Option No.
3100‐0068
3100‐0069
3100‐0074
3100‐0075
3100‐0076
3100‐0077
3100‐0078
3100‐0079
3100‐0080
3100‐0082
3100‐0084
3100‐0085
3100‐0087
3100‐0088
3100‐0089
3100‐0090
3100‐0091
3100‐0092
3100‐0093
3100‐0094
3100‐0095
Description
Driver side body with upper and lower compartmentation. Includes 60" wide forward and 42" wide rearward lower compartments, (3) opening upper compartments with portable water tank storage with access door at rear.
Driver side body with full height 60" wide forward and 42" wide rearward compartmentation. Includes (1) 56" wide compartment over the wheel well.
Driver side body with full height 36" wide rearward compartmentation. Includes (1) 56" wide compartment over the wheel well.
Driver side body with full height 36" wide rearward compartmentation. Includes (1) 56" wide compartment over the wheel well and 30 degree rear body angle for greater angle of departure.
Stainless steel driver side body with full height 36" wide forward and 48" wide rearward compartmentation (interior). Includes (1) 60" wide compartment over the wheel well.
Stainless steel driver side body with full height 48" wide forward and 48" wide rearward compartmentation (interior). Includes (1) 60" wide compartment over the wheel well.
Stainless steel driver side body with full height 60" wide forward and 60" wide rearward compartmentation (interior). Includes (1) 60" wide compartment over the wheel well.
Driver side body with full height 54" wide forward and 60" wide rearward compartmentation. Includes (1) 56" wide compartment over the wheel well. The compartment behind the wheel well has upper area for RM pump panel mounting.
Driver side body with full height 48" wide forward and 60" wide rearward compartmentation (interior). Includes (1) 60" wide compartment over the wheel well.
Stainless steel driver side body with full height 24" wide forward and 48" wide rearward compartmentation (interior). Includes (1) 60" wide compartment over the wheel well.
Stainless steel driver side body with full height 24" wide forward and 48" wide rearward compartmentation (interior). Includes (1) 60" wide compartment over the wheel well.
Driver half side body with 24" wide forward and 36" wide rearward compartmentation.
Driver half side body with 30" wide forward and 36" wide rearward compartmentation.
Officer half side stainless steel body with 36" wide forward and 48" wide rearward compartmentation (interior). Includes adjustable ladder tracks and brackets.
Driver half side body with 42" wide forward and 42" wide rearward compartmentation.
Driver half side body with 42" wide forward and 42" wide rearward compartmentation.
Driver side body with full height 60" wide forward and 56" wide rearward compartmentation. Includes (1) 56" wide compartment over the wheel well.
Driver side body with full height 50" wide enhanced extended rearward compartmentation. Includes (1) 56" wide compartment over the wheel well.
Driver side body with full height 24" wide forward and 36" wide rearward compartmentation. Includes (1) 56" wide compartment over the wheel well.
Driver side body with full height 30" wide forward and 36" wide rearward compartmentation. Includes (1) 56" wide compartment over the wheel well.
Driver side body with full height 36" wide forward and 36" wide rearward compartmentation. Includes (1) 56" wide compartment over the wheel well.
PRICE
$13,438.00
$12,597.00
$8,395.00
$8,744.00
$11,312.00
$12,951.00
$13,859.00
$18,281.00
$13,599.00
$9,676.00
$9,676.00
$4,493.00
$5,130.00
$5,660.00
$5,504.00
$5,504.00
$13,480.00
$9,312.00
$8,985.00
$9,612.00
$10,297.00
Option No.
3100‐0096
3100‐0097
3100‐0098
3100‐0099
3100‐0100
3100‐0101
3100‐0102
3100‐0103
3100‐0104
3100‐0105
3100‐0106
3100‐0107
3100‐0108
3100‐0109
3100‐0110
3100‐0111
3100‐0112
3100‐0113
Description
Driver side body with full height 42" wide forward and 42" wide rearward compartmentation. Includes (1) 56" wide compartment over the wheel well.
Driver side body with full height 48" wide forward and 48" wide rearward compartmentation. Includes (1) 56" wide compartment over the wheel well.
Driver side body with upper and lower compartmentation. Includes 24" wide forward and 36" wide rearward lower compartments and (3) opening upper compartments.
Driver side body with upper and lower compartmentation. Includes 30" wide forward and 36" wide rearward lower compartments and (3) opening upper compartments.
Driver side body with upper and lower compartmentation. Includes 36" wide forward and 36" wide rearward lower compartments and (3) opening upper compartments.
Driver side body with upper and lower compartmentation. Includes 42" wide forward and 42" wide rearward lower compartments and (3) opening upper compartments.
Driver side body with upper and lower compartmentation. Includes 48" wide forward and 48" wide rearward lower compartments and (3) opening upper compartments.
Driver side body with upper and lower compartmentation. Includes 42" wide forward and 42" wide rearward lower compartments, (3) opening upper compartments with portable water tank storage with access door at rear.
Driver side body with upper and lower compartmentation. Includes 48" wide forward and 48" wide rearward lower compartments, (3) opening upper compartments with portable water tank storage with access door at rear.
Driver side body with full height 24" wide forward and 50" wide rearward extended compartmentation. Includes (1) 56" wide compartment over the wheel well.
Driver side body with full height 30" wide forward and 50" wide rearward extended compartmentation. Includes (1) 56" wide compartment over the wheel well.
Driver side body with full height 36" wide forward and 50" wide rearward extended compartmentation. Includes (1) 56" wide compartment over the wheel well.
Driver side body with full height 42" wide forward and 56" wide rearward extended compartmentation. Includes (1) 56" wide compartment over the wheel well.
Driver side body with full height 48" wide forward and 62" wide rearward extended compartmentation. Includes (1) 56" wide compartment over the wheel well.
Driver side body with full height 24" wide forward and 50" wide rearward enhanced extended compartmentation. Includes (1) 56" wide compartment over the wheel well.
Driver side body with full height 30" wide forward and 50" wide rearward enhanced extended compartmentation. Includes (1) 56" wide compartment over the wheel well.
Driver side body with full height 36" wide forward and 50" wide rearward enhanced extended compartmentation. Includes (1) 56" wide compartment over the wheel well.
Driver side body with full height 42" wide forward and 56" wide rearward enhanced extended compartmentation. Includes (1) 56" wide compartment over the wheel well.
PRICE
$11,005.00
$11,773.00
$9,434.00
$10,061.00
$10,733.00
$11,454.00
$12,224.00
$11,796.00
$12,590.00
$9,612.00
$10,244.00
$10,912.00
$11,633.00
$12,403.00
$9,902.00
$10,529.00
$11,200.00
$11,922.00
Option No.
3100‐0114
3100‐0115
3100‐0116
3100‐0117
3100‐0118
3100‐0119
3100‐0120
3100‐0121
3100‐0122
3100‐0123
3100‐0124
3100‐0125
3100‐0126
3100‐0127
3100‐0128
3100‐0129
3100‐0130
3100‐0131
3100‐0132
Description
Driver side body with full height 48" wide forward and 62" wide rearward enhanced extended compartmentation. Includes (1) 56" wide compartment over the wheel well.
Driver side body with full height 36" wide forward and 36" wide rearward compartmentation. Includes (1) 56" wide compartment over the wheel well.
Driver side body with full height 42" wide forward and 42" wide rearward compartmentation. Includes (1) 56" wide compartment over the wheel well.
Driver side body with full height 48" wide forward and 48" wide rearward compartmentation. Includes (1) 56" wide compartment over the wheel well.
Driver side body with full height 24in. wide forward and 36in. wide rearward compartmentation. Includes (1) 56in. wide compartment over the wheel well and 30 degree rear body angle for greater angle of departure.
Driver side body with full height 30" wide forward and 36" wide rearward compartmentation. Includes (1) 56" wide compartment over the wheel well and 30 degree rear body angle for greater angle of departure.
Driver side body with full height 36" wide forward and 36" wide rearward compartmentation. Includes (1) 56" wide compartment over the wheel well and 30 degree rear body angle for greater angle of departure.
Stainless steel driver side body with full height 36" wide forward and 48" wide rearward compartmentation (interior). Includes (1) 60" wide compartment over the wheel well.
Stainless steel driver side body with full height 48" wide forward and 48" wide rearward compartmentation (interior). Includes (1) 60" wide compartment over the wheel well.
Stainless steel driver side body with full height 60" wide forward and 60" wide rearward compartmentation (interior). Includes (1) 60" wide compartment over the wheel well.
Stainless steel driver side body with full height 48" wide forward and 60" wide rearward compartmentation (interior). Includes (1) 60" wide compartment over the wheel well.
Driver side body with full height 60" wide forward and 42" wide rearward compartmentation. Includes (1) 56" wide compartment over the wheel well.
Driver side body with upper and lower compartmentation. Includes 60" wide forward and 42" wide rearward lower compartments and (3) opening upper compartments.
Driver side body with upper and lower compartmentation. Includes 60" wide forward and 42" wide rearward lower compartments, (3) opening upper compartments with portable water tank storage with access door at rear.
Driver side body with full height 60" wide forward and 42" wide rearward compartmentation. Includes (1) 56" wide compartment over the wheel well.
Driver side body with full height 36" wide rearward compartmentation. Includes (1) 56" wide compartment over the wheel well.
Driver side body with full height 36" wide rearward compartmentation. Includes (1) 56" wide compartment over the wheel well and 30 degree rear body angle for greater angle of departure.
Stainless steel driver side body with full height 36" wide forward and 48" wide rearward compartmentation (interior). Includes (1) 60" wide compartment over the wheel well.
Stainless steel driver side body with full height 48" wide forward and 48" wide rearward compartmentation (interior). Includes (1) 60" wide compartment over the wheel well.
PRICE
$12,690.00
$11,005.00
$11,773.00
$12,597.00
$9,332.00
$9,960.00
$10,631.00
$11,312.00
$12,951.00
$13,859.00
$13,599.00
$13,480.00
$13,078.00
$13,438.00
$12,597.00
$8,395.00
$8,744.00
$11,312.00
$12,951.00
Option No.
3100‐0133
3100‐0134
3100‐0135
3100‐0136
3100‐0137
3100‐0138
3100‐0139
3100‐0140
3100‐0142
3100‐0143
3100‐0144
3100‐0145
3100‐0146
3100‐0148
3100‐0149
3100‐0151
3100‐0152
3100‐0153
3100‐0154
Description
Stainless steel driver side body with full height 60" wide forward and 60" wide rearward compartmentation (interior). Includes (1) 60" wide compartment over the wheel well.
Stainless Steel Driver side body with full height 48" wide forward and 60" wide rearward compartmentation (interior). Includes (1) 60" wide compartment over the wheel well.
Driver side body with full height 60" wide forward and 56" wide rearward compartmentation. Includes (1) 56" wide compartment over the wheel well. Top Mount eMAX Only.
Driver side tunnel to hold: Lower section (3) Backboards. Upper section (1) Divider full length of tunnel, bolted at rear of tunnel and held in place by a slot in the front of the tunnel for removability.
Driver side compartment top storage box. Box to be smooth plate and painted job color with diamond plate top. Box to have a rear vertically hinged door with push‐button latch. Box to have diamond plate lids with push button latches.
Driver side body with upper and lower compartmentation. Includes 24" wide forward and 36" wide rearward lower compartments and (2) opening upper compartments.
Compartment L1 to have rescue style interior compartment depth and height.
Driver side 36"/48" assembly. Includes upper and lower compartments with diamond plate compartment top. Upper area is for storage of hardsuction rack (not included).
Driver side body with full height 42" wide forward and 48" wide rearward compartmentation. Includes (1) 56" wide compartment over the wheel well and upper area for recessed pike pole storage.
Driver side body with full height 52" wide forward and 52" wide rearward compartmentation. Includes (1) 56" wide compartment over the wheel well.
Driver side body with full height 36" wide forward and 50" wide rearward compartmentation. Includes (1) 56" wide compartment over the wheel well.
Driver side body with full height 30" wide forward and 50" wide rearward compartmentation. Includes (1) 56" wide compartment over the wheel well.
Driver side body with full height 24" wide forward and 50" wide rearward compartmentation. Includes (1) 56" wide compartment over the wheel well.
Driver side body with full height 42" wide forward and 56" wide rearward compartmentation. Includes (1) 56" wide compartment over the wheel well.
Driver side body with full height 36" wide forward and 42" wide rearward compartmentation. Includes (1) 56" wide compartment over the wheel well.
Driver side body with 42" wide x 38" high wide forward lower compartmentation and 42" wide x 26.75" high forward upper compartmentation. 42" wide full height rearward compartmentation. Includes (1) 56" wide compartment over the wheel well.
Driver side body with full height 36" wide forward and 50" wide rearward enhanced extended compartmentation. Includes (1) 56" wide compartment over the wheel well.
Driver side body with full height 42" wide forward and 56" wide rearward enhanced extended compartmentation. Includes (1) 56" wide compartment over the wheel well.
Driver side body with full height 48" wide forward and 62" wide rearward enhanced extended compartmentation. Includes (1) 56" wide compartment over the wheel well.
PRICE
$13,859.00
$13,599.00
$13,480.00
$640.00
$1,909.00
$9,434.00
$1,526.00
$12,586.00
$11,005.00
$12,597.00
$11,200.00
$10,529.00
$9,902.00
$11,872.00
$11,773.00
$12,952.00
$11,907.00
$12,677.00
$13,502.00
Option No.
3100‐0155
3100‐0156
3100‐0157
3100‐0158
3100‐0159
3100‐0160
3100‐0161
3100‐0162
3100‐0163
3100‐0164
3100‐0165
3100‐0166
3100‐0167
3100‐0168
3100‐0169
3100‐0170
3100‐0171
3100‐0172
Description
Driver side body with full height 60" wide forward and 56" wide rearward enhanced extended compartmentation. Includes (1) 56" wide compartment over the wheel well.
Driver side body with full height 30" wide forward and 36" wide rearward compartmentation. Includes (1) 56" wide compartment over the wheel well. Front and rear compartment opening height to be 66.75" high.
Driver side body with upper and lower compartmentation. Includes 42" wide forward and 42" wide rearward lower compartments and (3) opening upper compartments.
Portable water tank storage with access door at rear. Includes composite material overlay and door ajar switch.
Driver side body with full height 42" wide forward and 56" wide rearward enhanced extended compartmentation. Includes (1) 56" wide compartment over the wheel well and one (1) storage tunnel and access door at rear.
Driver side body with full height 30" wide forward and 50" wide rearward enhanced extended compartmentation. Includes (1) 56" wide compartment over the wheel well.
Driver side body with 42" wide x 30" high wide forward lower compartmentation and 42" wide x 34.75" high forward upper compartmentation. 42" wide full height rearward compartmentation. Includes (1) 56" wide compartment over the wheel well.
2‐Arm Ladder Rack. The ladder rack includes amber lights on each end to visually indicate when the rack is in motion. Ladder rack to hold storage box with (1) vertically hinged rearward and (2) horizontally hinged outboard (when ladder rack in the down position) diamond plate doors with push button latches. The outboard horizontally hinged door(s) to have chains set to open at approx 160 degrees. Forward section of the box to hold (2) backboards and the rearward section to hold (1) stokes basket.
Driver side body with full height 50" wide forward and 50" wide rearward enhanced extended compartmentation. Includes (1) 56" wide compartment over the wheel well.
Driver side body with full height 56" wide forward and 56" wide rearward enhanced extended compartmentation. Includes (1) 56" wide compartment over the wheel well.
Driver side body with full height 62" wide forward and 62" wide rearward enhanced extended compartmentation. Includes (1) 56" wide compartment over the wheel well.
Driver side tunnel to hold: [#LOC].
Driver side body with full height 62" wide forward and 62" wide rearward enhanced extended compartmentation. Includes (1) 56" wide compartment over the wheel well.
Driver side body with full height 30" wide forward and 50" wide rearward enhanced extended compartmentation. Includes (1) 56" wide compartment over the wheel well. Rear compartment to be pumper style enhanced extended (shallow upper and deep lower compartmentation).
Overhead Ladder Rack to be offset rearward includes shifting compartment (forward) over the wheel well.
Driver side body with 62" wide full height forward enhanced extended compartment, 36" wide half height second forward compartment and 50" wide half height rearward compartmentation.
Driver side body with full height 24" wide forward and 50" wide rearward extended compartmentation. Includes (1) 33" wide compartment over the wheel well and (1) Zico Overhead Ladder Rack.
Driver side body with full height 24" wide forward and 56" wide rearward extended compartmentation. Includes (1) 56" wide compartment over the wheel well.
PRICE
$14,384.00
$10,290.00
$11,005.00
$793.00
$15,596.00
$11,191.00
$14,188.00
$18,476.00
$12,677.00
$13,502.00
$14,323.00
$640.00
$13,465.00
$13,046.00
$0.00
$18,556.00
$16,167.00
$10,485.00
Option No.
3100‐0173
3100‐0174
3100‐0175
3100‐0176
3100‐0177
3100‐0178
3100‐0179
3100‐0180
3100‐0181
3100‐0182
3100‐0183
3100‐0184
3100‐0185
3100‐0186
3100‐0187
3100‐0188
3100‐0189
3100‐0190
Description
Driver side body with full height 24" wide forward and 50" wide rearward enhanced extended compartmentation. Includes (1) 56" wide compartment over the wheel well. Rear compartment to be pumper style enhanced extended (shallow upper and deep lower compartmentation).
Driver side body with upper and lower compartmentation. Includes 36" wide forward and 50" wide rearward extended lower compartments and (3) opening upper compartments.
Driver side body with full height 36" wide forward and 36" wide rearward compartmentation. Includes (1) 56" wide compartment over the wheel well and one (1) storage tunnel.
Driver side body with full height 36" wide forward and 50" wide rearward enhanced extended compartmentation. Includes (1) 56" wide compartment over the wheel well and one (1) storage tunnel.
Driver side body with full height 42" wide forward and 42" wide rearward compartmentation. Includes (1) 56" wide compartment over the wheel well and one (1) storage tunnel.
Driver side body with full height 42" wide forward and 56" wide rearward enhanced extended compartmentation. Includes (1) 56" wide compartment over the wheel well and one (1) storage tunnel.
Driver side body with full height 48" wide forward and 48" wide rearward compartmentation. Includes (1) 56" wide compartment over the wheel well and one (1) storage tunnel.
Driver side body with full height 48" wide forward and 62" wide rearward enhanced extended compartmentation. Includes (1) 56" wide compartment over the wheel well and one (1) storage tunnel.
Driver side body with full height 60" wide forward and 42" wide rearward compartmentation. Includes (1) 56" wide compartment over the wheel well and one (1) storage tunnel.
Driver side body with full height 60" wide forward and 56" wide rearward enhanced extended compartmentation. Includes (1) 56" wide compartment over the wheel well and one (1) storage tunnel.
Driver side body with full height 36" wide forward and 50" wide rearward enhanced extended compartmentation (2008 body design) with (1) 56" wide compartment over the wheel well.
Driver side internal portable tank storage to be set‐up for: [#LOC]
Driver side body with full height 20" wide forward and 50" wide rearward extended compartmentation. Includes (1) 56" wide compartment over the wheel well.
Driver side upper body extension. Does not include any external doors. External framework and platework only. Platework shall be recessed.
Stainless steel driver side body with full height 30" wide forward and 40" wide rearward compartmentation. Includes (1) 54" wide compartment over the wheel well.
Stainless steel driver side body with full height 40" wide forward and 40" wide rearward compartmentation. Includes (1) 54" wide compartment over the wheel well.
Stainless steel driver side body with full height 48" wide forward and 40" wide rearward compartmentation. Includes (1) 54" wide compartment over the wheel well.
Stainless steel driver side body with full height 30" wide forward and 58" wide rearward enhanced extended compartmentation. Includes (1) 54" wide compartment over the wheel well.
PRICE
$13,862.00
$15,763.00
$13,922.00
$14,825.00
$14,691.00
$15,596.00
$15,515.00
$16,420.00
$16,399.00
$17,299.00
$17,286.00
$0.00
$9,400.00
$2,219.00
$25,129.00
$26,522.00
$27,289.00
$26,045.00
Option No.
3100‐0191
3100‐0192
3100‐0194
3100‐0195
3100‐0196
3100‐0197
3100‐0198
3100‐0199
3100‐0201
3100‐0202
3100‐0203
3100‐0204
3100‐0207
3100‐0208
3100‐0209
3100‐0210
3100‐0211
3100‐0212
3100‐0213
Description
Stainless steel driver side body with full height 40" wide forward and 58" wide rearward enhanced extended compartmentation. Includes (1) 54" wide compartment over the wheel well.
Stainless steel driver side body with full height 48" wide forward and 58" wide rearward enhanced extended compartmentation. Includes (1) 54" wide compartment over the wheel well.
Stainless steel driver side body with full height/full depth 48" wide forward and 40" wide rearward compartmentation. Includes (1) 54" wide compartment over the wheel well.
Driver 3/4 side body with full height 36" wide forward and 36" wide rearward compartmentation. Includes (1) 56" wide compartment over the wheel well.
Driver half side body with (2) forward compartments (48" and 30" wide) and one rearward area for locating of side tank dump.
Driver half side body with (2) forward compartments (48" and 30" wide) and (1) rearward compartment (24").
Driver 3/4 side body with (2) lower forward compartments (48" and 30" wide), (3) upper compartments (54") and one lower rearward area for locating of side tank dump.
Driver 3/4 side body with (2) lower forward compartments (48" and 30" wide), (3) upper compartments (54") and (1) lower rearward compartment (24").
Driver full height side body with (2) lower forward compartments (48" and 30" wide), (3) upper compartments (54") and one lower rearward area for locating of side tank dump.
Driver full height side body with (2) lower forward compartments (48" and 30" wide), (3) upper compartments (54") and (1) lower rearward compartment (24").
Driver full height side body with (2) full height, rescue style, forward compartments (48" and 30" wide), (1) upper compartment (61" and offset rearward of the rack opening) and one lower rearward area for locating of side tank dump.
Driver full height side body with (2) full height, rescue style, forward compartments (48" and 30" wide), (1) upper compartment (61" and offset rearward of the rack opening) and (1) lower rearward compartment (24").
Driver full height side body with (2) lower forward compartments (48" and 30" wide), (3) upper compartments (54") with rear compartment face access door for portable tank storage and one lower rearward area for locating of side tank dump.
Driver full height side body with (2) lower forward compartments (48" and 30" wide), (3) upper compartments (54") with rear compartment face access door for portable tank storage and (1) lower rearward compartment (24").
Driver side body with full height 24" wide forward and 50" wide rearward enhanced extended compartmentation. Includes (1) 56" wide compartment over the wheel well.
Driver full height side body with (2) full height, rescue style, forward compartments (48" and 30" wide), (2) upper compartment (40" wide) and (1) lower rearward compartment (24").
Driver full height side body with (2) full height, rescue style, forward compartments (48" and 30" wide), (2) upper compartments (40" wide) and one lower rearward area for locating of side tank dump.
(1) driver side roof top compartments with extra width to inboard side. Includes hinged raised compartment lid with turn latches, grab handle(s) and gas shock hold open and drain line(s) ran to below body. The lid to have (1) bracket mounted LED light and to be wired to door ajar indicator in cab.
Stainless steel driver side body with full height 48" wide forward and 48" wide rearward compartmentation. Includes (1) 54" wide compartment over the wheel well.
PRICE
$27,438.00
$28,207.00
$27,289.00
$6,428.00
$5,011.00
$5,897.00
$6,930.00
$7,810.00
$8,850.00
$9,731.00
$8,850.00
$9,731.00
$10,249.00
$11,128.00
$10,477.00
$9,731.00
$8,850.00
$5,466.00
$28,114.00
Option No.
3100‐0214
3100‐0215
3100‐0216
3100‐0218
3100‐0219
3100‐0220
3100‐0221
3100‐0222
3100‐0223
3100‐0224
3100‐0225
3100‐0226
3100‐0227
3100‐0228
3100‐0229
3100‐0230
3100‐0231
3100‐0232
3100‐0233
3100‐0234
3100‐0235
3100‐0236
Description
Stainless steel driver side body with full height 54" wide forward and 54" wide rearward compartmentation. Includes (1) 54" wide compartment over the wheel well.
Stainless steel driver side body with full height 60" wide forward and 60" wide rearward compartmentation. Includes (1) 54" wide compartment over the wheel well.
Compartment L1 to be 48.75" high in full depth lower area due to pipe routing for deck gun in hosebed storage pan.
Driver side storage tunnel to hold (2) 6" x 10' hard suction hoses.
Driver half side body with 42" wide forward and 42" wide rearward compartmentation. Includes adjustable ladder tracks.
Overhead Ladder Rack to be offset forward includes shifting compartment (rearward) over the wheel well.
Driver half side tandem body with 30" wide forward and 30" wide rearward compartmentation.
Driver half side tandem body with 42" wide forward and 42" wide rearward compartmentation.
Driver half side tandem body with 60" wide forward and 54" wide rearward compartmentation.
Driver 3/4 side tandem body with full height 30" wide forward and 30" wide rearward compartmentation. Includes (2) 51.5" wide compartments over the wheel well.
Driver 3/4 side tandem body with full height 42" wide forward and 42" wide rearward compartmentation. Includes (2) 51.5" wide compartments over the wheel well.
Driver 3/4 side tandem body with full height 60" wide forward and 54" wide rearward compartmentation. Includes (2) 51.5" wide compartments over the wheel well.
Driver side tandem body with upper and lower compartmentation. Includes 30" wide forward and 30" wide rearward compartments and (4) opening upper compartments.
Driver side tandem body with upper and lower compartmentation. Includes 42" wide forward and 42" wide rearward compartments and (4) opening upper compartments.
Driver side tandem body with upper and lower compartmentation. Includes 60" wide forward and 54" wide rearward compartments and (4) opening upper compartments.
Driver side tandem body with upper and lower compartmentation. Includes 30" wide forward and 30" wide rearward compartments and (4) opening upper compartments. Includes overhead rack opening centered between upper compartments.
Driver side tandem body with upper and lower compartmentation. Includes 42" wide forward and 42" wide rearward compartments and (4) opening upper compartments. Includes overhead rack opening centered between upper compartments.
Driver side tandem body with upper and lower compartmentation. Includes 60" wide forward and 54" wide rearward compartments and (4) opening upper compartments. Includes overhead rack opening centered between upper compartments.
Driver side tandem body with full height 30" wide forward and 30" wide rearward compartmentation. Includes (2) 51.5" wide compartments over the wheel well.
Driver side tandem body with full height 42" wide forward and 42" wide rearward compartmentation. Includes (2) 51.5" wide compartments over the wheel well.
Driver side tandem body with full height 60" wide forward and 54" wide rearward compartmentation. Includes (2) 51.5" wide compartments over the wheel well.
Driver side tandem body with full height 30" wide forward and 30" wide rearward compartmentation. Includes (2) 42" wide compartments over the wheel well and overhead rack opening centered between upper compartments.
PRICE
$29,122.00
$30,130.00
$577.00
$1,988.00
$5,504.00
$609.00
$7,519.00
$8,214.00
$9,013.00
$8,707.00
$9,574.00
$10,570.00
$12,756.00
$14,150.00
$15,773.00
$13,265.00
$14,714.00
$16,403.00
$12,309.00
$13,701.00
$15,292.00
$12,799.00
Option No.
3100‐0237
3100‐0238
3100‐0239
3100‐0240
3100‐0241
3100‐0242
3100‐0243
3100‐0244
3100‐0245
3100‐0246
3100‐0247
3100‐0248
3100‐0249
3100‐0250
3100‐0251
3100‐0252
3100‐0253
3100‐0254
Description
Driver side tandem body with full height 42" wide forward and 42" wide rearward compartmentation. Includes (2) 42" wide compartments over the wheel well and overhead rack opening centered between upper compartments.‐
Driver side tandem body with full height 60" wide forward and 54" wide rearward compartmentation. Includes (2) 42" wide compartments over the wheel well and overhead rack opening centered between upper compartments.
Driver side body with full height 36" wide forward and 36" wide rearward compartmentation. Includes (1) 56" wide compartment over the wheel well.
Driver side body with full height 42" wide forward and 42" wide rearward compartmentation. Includes (1) 56" wide compartment over the wheel well.
Driver side body with upper and lower compartmentation. Includes 36" wide forward and 36" wide rearward lower compartments and (3) opening upper compartments.
Driver side body with upper and lower compartmentation. Includes 42" wide forward and 42" wide rearward lower compartments and (3) opening upper compartments.
Driver side body with full height 42" wide forward and 50" wide rearward compartmentation. Includes (1) 56" wide compartment over the wheel well.
Driver half side tandem body with with 42" wide forward and one rearward area for locating of side tank dump rearward of the wheel well.
Driver side body with full height 60" wide forward and 56" wide rearward compartmentation. Includes (1) 56" wide compartment over the wheel well. Side Mount eMAX only.
Driver side body with upper and lower compartmentation. Includes 36" wide forward and 31" wide rearward lower compartments and (2) opening upper compartments.
Driver side body with full height 46" wide forward and 56" wide rearward enhanced extended compartmentation. Includes (1) 56" wide compartment over the wheel well. L1 compartment to be Rescue Pumper style individual compartments.
Driver side body with full height 50" wide forward and 50" wide rearward compartmentation. Includes (1) 56" wide compartment over the wheel well.
Driver side body with full height 36" wide forward and 50" wide rearward compartmentation. Includes (1) 56" wide compartment over the wheel well.
Driver side body with full height 60" wide forward and 62" wide rearward enhanced extended compartmentation. Includes (1) 56" wide compartment over the wheel well.
Driver side body with full height 60" wide forward and 42" wide rearward compartmentation. Includes (1) 33" wide compartment over the wheel well and (1) Zico Overhead Portable Tank Rack. Rack to hold (1) 3000 gallon portable tank.
Driver side body with full height 42" wide forward and 56" wide rearward enhanced extended compartmentation. Includes (1) 56" wide compartment over the wheel well.
Driver full height side body with (3) full height, rescue style, forward compartments (39" and 39" wide and rearward of wheel well 24" wide),(1) upper compartment over the wheel well 56" wide.
Driver side body with upper and lower compartmentation. Includes 48" wide forward and 62" wide enhanced extended rearward lower compartments and (3) opening upper compartments.
PRICE
$14,247.00
$15,904.00
$10,297.00
$11,005.00
$10,733.00
$11,454.00
$11,535.00
$8,502.00
$13,480.00
$10,733.00
$14,075.00
$13,480.00
$10,733.00
$14,824.00
$18,788.00
$13,251.00
$9,812.00
$13,344.00
Option No.
3100‐0255
3100‐0256
3100‐0257
3100‐0258
3100‐0259
3100‐0260
3100‐0261
3100‐0262
3100‐0263
3100‐0264
3100‐0265
3100‐0266
3100‐0267
3100‐0268
3100‐0269
3100‐0270
3100‐0271
3100‐0272
Description
Driver side body with full height 42" wide forward and 56" wide rearward enhanced extended compartmentation. Includes (1) 33" wide compartment over the wheel well and (1) Zico Overhead Ladder Rack.
Zico ladder rack to be tested. After testing ladder rack to be disassembled and repackaged for shipping.
Driver side body with full height 36" wide forward and 50" wide rearward enhanced extended compartmentation. Includes (1) 33" wide compartment over the wheel well and (1) Zico Overhead Ladder Rack.
Driver extruded half side tandem body with 74" wide forward and 34" wide rearward compartmentation.For use with wetside narrow tank application.
Driver side diamond plate roof top compartment. Includes smooth plate painted vertical hinged access door at the rear with push button latch to be wired to door ajar indicator in cab.
Driver side body with full height 36" wide forward and 45" wide rearward compartmentation. Includes (1) 56" wide compartment over the wheel well.
Driver side body with full height 19.5" wide forward and 31" wide rearward compartmentation. Includes (1) 40" wide compartment over the wheel well.
Driver side body with full height 32" wide forward and 50" enhanced extended rearward compartmentation. Includes (1) 56" wide compartment over the wheel well.
Driver side body with full height 54" wide forward and 48" wide rearward compartmentation. Includes (1) 56" wide compartment over the wheel well. Side Mount eMAX only.
Driver side body with full height 26" and 56" wide forward compartments and 56" wide rearward compartmentation. Includes (1) 56" wide compartment over the wheel well. Side Mount eMAX only.
Driver side diamond plate roof top compartment. Includes (2) hinged lift‐up access doors with turn latches and grab handle(s) and (1) vertical hinged access door at the rear with push button latch to be. Each lid to have (1) bracket mounted LED light and to be wired to door ajar indicator in cab.
Driver side body with full height/full depth 60" wide front and 54" wide rear compartment. Includes (1) 60" wide compartment over the wheel well. Side mount SS eMAX only.
Driver side tandem body with upper and lower compartmentation. Includes 60" wide forward and 54" wide rearward compartments and (1) opening forward upper compartment with painted panels rearward.
Left Side Exterior Compartments. L1, 60" wide x 63" high x 48" deep (over frame) full height with vertically hinged doors. L2, 58" wide x 63" high x 27.5" deep (over frame) full height with vertically hinged doors. L3, 60" wide x 33" high x 27.5" deep full height with vertically hinged doors. L4, 50" wide x 63" high x 27.5" deep (over frame) full height with vertically hinged doors.
Driver side body with full height 44" wide forward and 48" wide rearward compartmentation. Includes (1) 56" wide compartment over the wheel well. Side Mount eMAX only.
Rear aluminum smooth plate painted job color vertical hinged door on driver side roof top compartments. Includes thumb latch and wiring for door ajar switch.
Stainless steel driver side body with full height/full depth 36" wide front and 48" rear for reverse hinge compartment L1 door. Includes 54" wide compartment above rear wheels.
Stainless steel driver side body with 76" full height interior, 48" wide forward and 40" wide rearward compartmentation. Includes (1) 54" wide compartment over the wheel well.
PRICE
$19,690.00
$427.00
$17,754.00
$5,468.00
$1,592.00
$11,820.00
$9,902.00
$9,317.00
$12,636.00
$14,885.00
$2,292.00
$16,447.00
$16,880.00
$7,622.00
$12,192.00
$220.00
$28,735.00
$27,432.00
Option No.
3100‐0273
3100‐0274
3100‐0275
3100‐0276
3100‐0277
3100‐0278
3100‐0279
3100‐0280
3100‐0281
3100‐0282
3100‐0283
3100‐0285
3100‐0286
3100‐0287
3100‐0288
3100‐0289
Description
Driver side roof top compartment contents: (2) 6" x 10' hard suction hoses (not included) stored vertical. Includes vertical partition around hard suction hoses.
Driver side body with full height 36" wide forward and 56" wide rearward enhanced extended compartmentation. Includes (1) 56" wide compartment over the wheel well. Rescue Pumper individual style compartments.
Driver side tandem body with upper and lower compartmentation. Includes 30" wide forward and 54" wide rearward compartments and (4) opening upper compartments. Includes offseting upper compartments forward due to deck gun location and access panel on upper rear compartment face to deck gun piping.
(1) driver side roof top compartment forward of hard suction storage area and (2) roof top comaprtments over hard suction storage area. Includes hinged raised compartment lids with turn latches and grab handle(s). The lids to have (1) bracket mounted LED light and to be wired to door ajar indicator in cab. Includes partition between roof top compartment and hard suction storage area. Floor to be provided above the hard suction storage area to use remaining area above.
Driver side tandem body with 60" wide forward and 54" wide rearward compartmentation. Forward compartment to be full height, rearward to be half height.
Driver side body with full height 26" and 56" wide forward compartments and 56" wide rearward compartmentation. Includes (1) 56" wide compartment over the wheel well and one (1) storage tunnel. Side Mount eMAX only.
Driver side body with full height 54" wide forward and 36" wide rearward compartmentation. Includes (1) 56" wide compartment over the wheel well. Side Mount eMAX only.
Driver side roof top assembly. Does not include external upper doors or internal platework. External framework and platework only.
Driver side body with full height 36" wide forward and 36" wide rearward compartmentation. Includes (1) 56" wide compartment over the wheel well and 30 degree rear body angle for greater angle of departure. L1 compartment to be Rescue Pumper style individual compartments.
Driver full height side body with 66" wide forward and 42" wide rearward compartmentation. Includes (1) 56" wide compartment over the wheel well. For use with custom chassis only.
Driver half side body with (2) forward compartments (48" and 30" wide) and one rearward area for locating of side tank dump. Includes (1) 20" wide compartment above the lower forward comaprtment.
Driver side tandem body with full height 42" wide forward and 59" wide rearward compartmentation. Includes (2) 51.5" wide compartments over the wheel well.
Driver side body with upper and lower compartmentation. Includes 36" wide forward and 42" wide rearward lower compartments and (3) opening upper compartments.
Driver side body with 19.5" wide forward and 31" wide rearward compartmentation. Includes (1) 40" wide compartment over the wheel well.
Stainless steel driver side body with full height 54" wide front and 54" rear with reduced upper depth for "T" tank. Includes 54" wide compartment over rear wheels.
Stainless steel driver side body with full height 48" wide forward and 70" wide rearward enhanced extended compartmentation. Includes (1) 54" wide compartment over the wheel well.
PRICE
$1,088.00
$14,016.00
$14,158.00
$3,014.00
$11,106.00
$17,767.00
$12,192.00
$1,599.00
$12,156.00
$10,004.00
$5,503.00
$15,589.00
$11,094.00
$9,902.00
$28,551.00
$30,322.00
Option No.
3100‐0290
3100‐0291
3100‐0292
3100‐0293
3100‐0294
3100‐0295
3100‐0296
3100‐0298
3100‐0299
3100‐0300
3100‐0301
3100‐0302
3100‐0303
3100‐0304
3100‐0305
3100‐0306
Description
Driver side body with full height 48" wide forward and 48" wide rearward compartmentations. Includes (1) 56" wide compartment over the wheel well and one (1) storage tunnel. Tunnel to be behind L2 and L3 compartments only. L1 compartment to be full depth, full height with notch in upper rearward wall and boxed in cover for hard suction.
Driver side body with full height 48" wide forward and 48" wide rearward compartmentation. Includes (1) 56" wide compartment over the wheel well and one (1) storage tunnel. Tunnel to be behind L2 and L3 compartments only. L1 compartment to be full depth, full height with notch in upper rearward wall and boxed in cover for hard suction.
Stainless steel driver side body high side 60" front and 60" rear. Five compartments, tandem axle. For use with single arm overhead portable tank rack.
Driver side tandem body with upper and lower compartmentation. Includes 30" wide forward and 54" wide rearward compartments and (4) opening upper compartments. Includes offseting upper compartments forward due to deck gun location and access panel on upper rear compartment face to deck gun piping.
Driver side standard width roof top compartment contents: (2) 6" x 10' hard suction hoses (not included) stored vertical. The hard suction storage shall have a front wall which will prevent the hoses from sliding too far forward while also creating a full depth coffin storage area forward of the wall if applicable.
Driver side body with full height 26" and 56" wide forward compartments and 56" wide rearward compartmentation. Includes (1) 56" wide compartment over the wheel well for top mount application.
Driver side body with full height 26" and 56" wide forward compartments and 56" wide rearward compartmentation. Includes (1) 56" wide compartment over the wheel well and one (1) storage tunnel.
Stainless steel driver side short Boston style body with low height 36" front and 40" rear and (2) lift‐up doors above. Includes 60" wide fender panel. For use with optional suicide hinged L1 door.
Driver side tandem body with full height (1) 60" wide forward and (1) 60" wide rearward compartmentation. For use with Rear Mount pump.
Driver side body with full height/full depth 60" wide front and 54" wide rear compartment. Includes (1) 60" wide compartment over the wheel well. Top mount SS eMAX only.
Stainless steel driver side body with full height 60" wide forward and 60" wide rearward compartmentation. Includes (1) 54" wide compartment over the wheel well.
Stainless steel driver side body with full height 48" wide forward and 58" wide rearward enhanced extended compartmentation. Includes (1) 60" wide compartment over the wheel well. Body interior height is 76" high.
Stainless steel driver side body with full height 48" wide forward and 54" wide rearward compartmentation. Includes (1) 54" wide compartment over the wheel well.
Driver side tandem body with (2) 34" wide forward and 54" wide rearward compartmentation. Forward compartments to be full height, rearward to be half height.
(1) driver side roof top compartment (no divider). Includes (2) hinged raised compartment lids with turn latches and grab handle(s). Each lid to have (1) bracket mounted LED light and to be wired to door ajar indicator in cab.
(2) driver side roof top compartments with removable floors and extra width to inboard side. Includes hinged raised compartment lids with turn latches, grab handle(s) and gas shock hold open and drain line(s) ran to below body. Each lid to have (1) bracket mounted LED light and to be wired to door ajar indicator in cab.
PRICE
$17,068.00
$17,073.00
$18,980.00
$14,158.00
$346.00
$14,885.00
$17,767.00
$27,587.00
$18,931.00
$16,447.00
$33,432.00
$29,263.00
$28,207.00
$12,373.00
$2,735.00
$6,818.00
Option No.
3100‐0307
3100‐0308
3100‐0309
3100‐0310
3100‐0311
3100‐0312
3100‐0313
3100‐0314
3100‐0315
3100‐0316
3100‐0317
3100‐0318
3100‐0319
3100‐0320
3100‐0321
3100‐0322
Description
(2) Driver side roof top compartments. Includes hinged raised aluminum smooth plate with black Scorpion coating (IPOS diamond plate) compartment lids with turn latches and grab handle(s). Each lid to have (1) bracket mounted LED light and to be wired to door ajar indicator in cab.
Driver side body with full height 60" wide forward and 54" wide rearward compartmentation. Includes (1) 60" wide compartment over the wheel well. Top mount SS eMAX only.
Driver side body with full height 30" and 60" wide forward compartments and 54" wide rearward compartmentation. Includes (1) 60" wide compartment over the wheel well. Side mount SS eMAX only.
Driver side body with full height 30" and 60" wide forward compartments and 54" wide rearward compartmentation. Includes (1) 60" wide compartment over the wheel well, and a storage tunnel. Side mount SS eMAX only.
Driver side body with full height 30" and 60" wide forward compartments and 54" wide rearward compartmentation. Includes (1) 60" wide compartment over the wheel well. Top mount SS eMAX only.
Driver side body with full height 30" and 60" wide forward compartments and 54" wide rearward compartmentation. Includes (1) 60" wide compartment over the wheel well, and a storage tunnel. Top mount SS eMAX only.
Driver side body with full height 50" wide forward and 42" wide rearward compartmentation. Includes (1) 56" wide compartment over the wheel well. Rear perimeter or body raised 3" for improved departure angle. Side Mount eMAX only.
Driver full height side body with upper and lower compartmentation. Includes 42" wide forward and 56" wide rearward lower enhanced compartmentation and (3) opening upper compartments. For use with ladder storage in the hosebed
Driver side body with 19.5" wide forward and 31" wide rearward compartmentation. Includes (1) 40" wide compartment over the wheel well. Compartment tops raised approximately 6" to match hosebed height.
Stainless steel driver side body with rescue style full height 30" front, 40" rear and 60" wide fender panel L2 compartment. For use with suicide hinged L1 door (if applicable).
Horizontal partition located in driver side roof top compartment over DOT bottles. Floor to be provided above the DOT bottles to use remaining area above.
Driver side body with full height 48" wide forward and 56" wide rearward enhanced extended compartmentation. Includes (1) 56" wide compartment over the wheel well.
Driver side roof top compartment contents: (1) 10' hard suction hose (not included) stored horizontal. Includes stop bracket rearward of hard suction hoses and Nylatron compartment flooring.
(2) driver side roof top compartments with extra width to inboard side. Includes hinged raised compartment lids with turn latches, grab handle(s) and gas shock hold open and drain line(s) ran to below body. Each lid to have (1) bracket mounted LED light and to be wired to door ajar indicator in cab. Compartment lid construction shall be aluminum smooth plate IPO diamond plate painted Black Scorpion (rough finish).
Driver side body with upper and lower compartmentation. Includes 42" wide forward and 42" wide rearward lower compartments, (3) opening upper compartments with portable water tank storage with access door at rear. Smooth plate compartment top painted black durabak.
Driver 3/4 side body with (3) full height, rescue style, (2) forward compartments (48" and 30" wide) and (1) rearward compartment (24"). Includes (1) 56" wide compartment over the wheel well.
PRICE
$3,084.00
$20,005.00
$18,160.00
$21,676.00
$18,160.00
$21,676.00
$12,192.00
$11,922.00
$10,465.00
$27,587.00
$956.00
$13,502.00
$548.00
$5,881.00
$12,295.00
$8,276.00
Option No.
3100‐0323
3100‐0324
3100‐0325
3100‐0326
3100‐0327
3100‐0328
3100‐0329
3100‐0330
3100‐0331
3100‐0332
3100‐0333
3100‐0334
3100‐0335
3100‐0336
3100‐0337
3100‐0338
3100‐0339
Description
Driver 3/4 side tandem stainless steel body with 35" front and 35" rear for flat back body design. Includes (2) 42" wide compartments over rear tandem wheels, with side dump valve between.
Driver side roof top compartment. Includes vertically hinged access door at the rear with push button latch to be wired to door ajar indicator in cab.
(2) driver side roof top compartments with extra width to inboard side. Includes hinged raised compartment lids with turn latches, grab handle(s) and gas shock hold open and drain line(s) ran to below body. Each lid to have (2) bracket mounted LED lights and to be wired to
door ajar indicator in cab.
Driver side tandem body with upper and lower compartmentation. Includes 30" wide forward and 30" wide rearward compartments and (4) opening upper compartments.
Driver side body with full height 50" wide forward and 42" wide rearward compartmentation. Includes (1) 56" wide compartment over the wheel well. Rear perimeter or body raised 3" for improved departure angle.
Driver side upper body extension. Stainless Steel product only. Does not include external upper doors. External platework only and painted FRP covering.
Stainless steel driver side body with full height 48" wide forward and 48" wide rearward compartmentation. Includes (1) 54" wide compartment over the wheel well.
Driver 1/2 side tandem stainless steel tanker body with 60" front and 60" rear for flat back body design. Includes (2) 55" wide tandem wheel fender panels.
Driver side body with full height 24" wide forward and 36" wide rearward compartmentation. Includes (1) 56" wide compartment over the wheel well. Rear bottom corner of truck will be angled 30 degrees for a greater rear angle of departure.
Driver side body with full height 36" wide forward and 62" wide rearward enhanced extended compartmentation. Includes (1) 56" wide compartment over the wheel well.
Driver full height side body with 36" wide forward and 48" wide rearward compartmentation. Includes (2) 38" wide compartments over the wheel well and one forward area for side tank dump. For use with custom chassis only.
Driver side tandem body with full height 30" wide forward and 30" wide rearward compartmentation. Includes (2) 51.5" wide compartments over the wheel well.
Driver side body with full height 48" wide forward and 48" wide rearward compartmentation. Includes (1) 56" wide compartment over the wheel well. Compartment material to be 5083‐H321.
Driver full height side body with 42" wide and 20" wide forward compartments and 42" wide rearward compartment. Includes (1) 56" wide compartments over the wheel well. For use with custom chassis only.
Driver side body with full height 48" wide forward and 54" wide rearward compartmentation. Includes (1) 56" wide compartment over the wheel well.
Driver side body with full height 48" wide forward and 48" wide rearward compartmentation. Includes (1) 56" wide compartment over the wheel well.
Driver 3/4 side body with upper and lower compartmentation. Includes 42" wide forward and 42" wide rearward lower compartments and (2) opening upper compartments.
PRICE
$12,333.00
$1,592.00
$5,562.00
$13,575.00
$12,192.00
$1,376.00
$28,828.00
$14,031.00
$10,236.00
$12,792.00
$10,227.00
$13,407.00
$13,369.00
$10,227.00
$12,823.00
$12,597.00
$7,328.00
Option No.
3100‐0340
3100‐0341
3100‐0342
3100‐0343
3100‐0344
3100‐0345
3100‐0346
3100‐0347
3100‐0348
3100‐0349
3100‐0350
3100‐0351
3100‐0352
3100‐0354
3100‐0355
3100‐0356
3100‐0357
3100‐0358
Description
Driver side ERV body with full height 37" forward and 52" rearward. Includes (1) 56" wide compartment over the wheel well. Includes (2) roof top compartments with hinged raised lids with thumb latches, grab handle(s), and gas shock hold open and drain line(s) ran to below body.Eack lid to have (1) bracket mounted LED light and to be wired to door ajar indicator in cab.
Driver side body with full height 24" wide forward and 36" wide rearward compartmentation. Includes (1) 56" wide compartment over the wheel well.
Driver side body with full height 38" wide forward and 56" wide rearward compartment. Includes (1) 56" wide compartment over the wheel well.
(2) Driver side roof top compartments. Includes hinged raised compartment lids with thumb latches and grab handle(s). Each lid to have (1) bracket mounted LED light and to be wired to door ajar indicator in cab.
Driver half side tandem body with (2)41" wide forward and (2)32" wide rearward compartmentation.
Stainless steel driver side body with full height 48" wide forward and 54" wide rearward compartmentation. Includes (1) 60" wide compartment over the wheel well.
Stainless steel driver side body with full height 40" wide forward and 40" wide rearward compartmentation with reduced upper depth. Includes (1) 60" wide compartment over the wheel well.
Stainless steel driver side body with full height/full depth 40" wide forward and 48" wide rearward compartmentation. Includes (1) 60" wide compartment over the wheel well.
Driver side body with 42" wide full height forward and 42" wide lower rearward lower compartments and (2) opening upper compartments. Includes offseting upper compartments forward due to deck gun location and side facing access panels for deck gun piping.
Driver side roof top compartment contents: (1) 12'‐14'+ hard suction hose (not included) stored horizontal. Includes Nylatron compartment flooring. Length of capacity depends on body configuration.
Notch compartment L1 in forward ceiling area to allow for hose bed preconnect piping to route down into pump module.
Driver side body with full height 48" wide forward and 62" wide rearward compartmentation. Includes (1) 56" wide compartment over the wheel well.
Stainless steel driver side body with full height 48" wide forward and 58" wide rearward enhanced extended compartmentation. Includes (1) 60" wide compartment over the wheel well.
Driver side body with full height 54" wide forward and 48" wide rearward compartmentation. Includes (1) 56" wide compartment over the wheel well. Top Mount eMAX Only.
(2) driver side roof top compartments with extra width to inboard side. Includes hinged raised compartment lids with turn latches, grab handle(s) and gas shock hold open and drain line(s) ran to below body. Each lid to be wired to door ajar indicator in cab.
(2) driver side roof top compartments with extra width to inboard side. Includes hinged raised compartment lids with turn latches, grab handle(s) and gas shock hold open and drain line(s) ran to below body. Each lid to have (1) bracket mounted LED light and to be wired to door ajar indicator in cab.
Driver 3/4 height side body with 20" wide and 42" wide forward compartments and 42" wide rearward compartment. Includes (1) 56" wide compartments over the wheel well. For use with custom chassis only.
Driver side body with full height 42" wide forward and 56" wide rearward compartmentation. Includes (1) 56" wide compartment over the wheel well.
PRICE
$19,568.00
$10,236.00
$12,677.00
$2,735.00
$12,174.00
$12,248.00
$9,987.00
$27,289.00
$11,454.00
$638.00
$419.00
$12,690.00
$29,263.00
$12,636.00
$5,330.00
$5,466.00
$8,231.00
$13,251.00
Option No.
3100‐0359
3100‐0360
3100‐0361
3100‐0362
3100‐0363
3100‐0364
3100‐0365
3100‐0366
3100‐0367
3100‐0368
3100‐0369
3100‐0370
3100‐0371
3100‐0372
3100‐0373
3100‐0374
3100‐0375
Description
Stainless steel driver side tanker body high side 52" front and 52" rear rescue style, with Lord/coil spring torsion style body mounts. Four compartments, tandem axle.
Stainless steel driver side special tall body with full height 40" wide forward and 58" wide rearward enhanced extended compartmentation. Includes (1) 54" wide compartment over the wheel well.
Stainless steel driver side body with full height/full depth 48" wide forward and 48" wide rearward compartmentation. Includes (1) 54" wide compartment over the wheel well.
Driver side body with full height 50" wide forward and 36" wide rearward compartmentation. Includes (1) 56" wide compartment over the wheel well. Rear perimeter of body raised 4" for improved departure angle.
Driver side body with full height 42" wide forward and 54" wide rearward compartmentation. Includes (1) 56" wide compartment over the wheel well.
Stainless steel driver side body with full height 40" wide forward and 58" wide rearward enhanced extended compartmentation. Includes (1) 60" wide compartment over the wheel well.
Driver 3/4 side body with full height 24" wide forward and 36" wide rearward compartmentation. Includes (1) 56" wide compartment over the wheel well.
(2) driver side roof top compartments. Includes hinged raised compartment lids with slam style D‐ring latches and no grab handles. Each lid to have (1) bracket mounted LED light and to be wired to door ajar indicator in cab.
Driver side body with upper and lower compartmentation. Includes 42" wide forward and 42" wide rearward lower compartments and (2) opening upper compartments.
Driver side body with full height 26" and 30" wide forward compartments and 56" wide rearward compartmentation. Includes (1) 56" wide compartment over the wheel well. Side Mount eMAX only.
Driver side body with full height 60" wide forward and 42" wide rearward compartmentation. Includes (1) 33" wide compartment over the wheel well and (1) Zico Overhead Portable Tank Rack. Rack to hold (1) 2100 gallon portable tank.
Driver side body with full height 42" wide forward and 42" wide rearward compartmentation. Includes (1) 56" wide compartment over the wheel well.
Stainless steel driver side body with full height 40" wide forward and 58" wide rearward extended compartmentation. Includes (1) 60" wide compartment over the wheel well
Driver side smooth plate roof top compartment and paited black Durabak. Includes smooth plate vertically hinged access door at the rear with push button latch and painted job color to be wired to door ajar indicator in cab.
(2) driver side roof top compartments with extra width to inboard side. Includes hinged raised compartment lids with turn latches, grab handle(s) and gas shock hold open and drain line(s) ran to below body. Each lid to have (1) Amdor LED strip light and to be wired to door ajar indicator in cab.
Driver side roof top compartment contents: (2) 6" x 10' hard suction hoses (not included) stored horizontal side by side. Includes stop bracket rearward of hard suction hoses and partition over the hard suction hoses.
(2) driver side roof top compartments. Includes hinged raised compartment lids with turn latches and grab handle(s). Each lid to have (1) bracket mounted LED light and to be wired to door ajar indicator in cab. Includes fixed floor with hard suction storage below accessible through hinged rear panel access door with bent D‐ring latch.
PRICE
$21,183.00
$28,207.00
$28,828.00
$11,764.00
$11,773.00
$27,988.00
$5,617.00
$2,866.00
$11,454.00
$14,885.00
$18,788.00
$11,555.00
$27,694.00
$1,990.00
$6,243.00
$1,088.00
$3,599.00
Option No.
3100‐0376
3100‐0377
3100‐0378
3100‐0379
3100‐0380
3100‐0381
3100‐0382
3100‐0383
3100‐0384
3100‐0385
3100‐0386
3100‐0387
3100‐0388
3100‐0389
3100‐0390
3100‐0391
Description
Stainless steel driver side body with full height 34" wide forward and 48" wide rearward compartmentation and reduced upper depth for storage tunnel. Includes (1) 60" wide compartment over the wheel well.
Driver side body with full height 42" and 40" wide forward compartments and 56" wide rearward compartmentation. Includes (1) 56" wide compartment over the wheel well. Side Mount eMAX only.
Stainless steel driver side body with full height 30" wide forward and 58" wide rearward enhanced extended compartmentation. Includes (1) 60" wide compartment over the wheel well.
Driver Full height forward compartment and 3/4 side rear of L1 tandem body with 42" wide forward and 42" wide rearward compartmentation. Includes (2) 51.5" wide compartments over the wheel well. Lowered W/Well for extra compt heigth. Side Dump Valves between Tandems N/A.
(2) driver side roof top compartments. Includes hinged raised compartment lids with turn latches and grab handle(s). Each lid to have (3) bracket mounted EON LED lights and to be wired to door ajar indicator in cab.
Driver side tandem body with upper and lower compartmentation. Includes (2) 28" wide forward and 54" wide rearward compartments and (1) opening forward upper compartment with painted panels rearward.
The compartment opening width (interior to remain standard) shall be reduce 2" in the L1 and L3 compartments due to the mounting stanchion for the awning.
Stainless steel driver side short Boston style body with low height 30" front and 40" rear and (2) lift‐up doors above. Includes 60" wide fender panel. For use with optional suicide hinged L1 door.
Driver side tandem body with upper and lower compartmentation. Includes 60" wide full height forward and 54" wide half height rearward compartments and (1) opening forward upper compartment with painted panels rearward.
(2) Driver side roof top compartments with extra width to inboard side. Includes hinged raised compartment lids with turn latches, grab handle(s) and gas shock hold open and drain line(s) ran to below body. Each lid to have (1) bracket mounted LED light and to be wired to door ajar indicator in cab. Forward compartment to have standard floor. Rearward compartment shall be stepped at inboard side for a 26" deep section approximately 8.5" wide in order to stow a stokes basket on edge. Forward and rearward compartments to have a dividing wall between them to secure the different floor configurations. Stokes basket to be stored shall be a Ferno 71‐M basket or similar in size.
Driver side rear mount pumper body with full height 48" wide forward and 60" wide rearward compartmentation. Includes (1) 56" wide compartment over the wheel well and one (1) storage tunnel and access door at rear.
Driver side body with full height 60" wide forward and 48" wide rearward compartmentation. Includes (1) 56" wide compartment over the wheel well. Side Mount eMAX only.
(2) driver side roof top compartments for instillation of DOT/ASME bottles. Includes hinged raised compartment lids with turn latches and grab handle(s). Each lid to have (1) bracket mounted LED light and to be wired to door ajar indicator in cab.
Driver side body with full height 34" and 48" wide forward compartments and 56" wide rearward compartmentation. Includes (1) 56" wide compartment over the wheel well. Side Mount eMAX only.
Driver side body with full height 30" wide forward and 44" wide rearward compartmentation. Includes (1) 56" wide compartment over the wheel well.
Stainless steel driver side body with full height/full depth 60" wide forward and 60" wide rearward compartmentation. Includes (1) 60" wide compartment over the wheel well.
PRICE
$28,399.00
$15,421.00
$27,145.00
$14,398.00
$2,735.00
$17,429.00
$268.00
$26,313.00
$17,433.00
$6,407.00
$17,539.00
$13,480.00
$2,735.00
$15,421.00
$11,200.00
$31,184.00
Option No.
3100‐0392
3100‐0393
3100‐0394
3100‐0395
3100‐0396
3100‐0397
3100‐0398
3100‐0399
3100‐0400
3100‐0401
3100‐0402
3100‐0403
3100‐0404
3100‐0405
3100‐0406
3100‐0407
3100‐0408
Description
Driver side body with full height 26" and 50" wide forward compts, 56" wide over wheel compt and 52" wide rearward compt. Includes slide‐back rear side compt for engine access. Side Mount eMAX HS only.
Stainless steel driver side body with full height 48" wide forward and 40" wide rearward compartmentation. Includes (1) 60" wide compartment over the wheel well.
Driver side rear mount rescue pumper body with full height 38" wide forward and 42" wide rearward compartmentation. Includes (1) 56" wide compartment over the wheel well and 30 degree angled rear body for improved angle of departure.
Driver full height body side with (1) 48" wide, Full Height forward compartment, (1) 30" wide, lower forward compartment adjacent to w/well, (2) upper compartments (57" wide each), the rearward upper having a rear compartment face access door for portable tank storage, and (1) lower rearward compartment (24") to rear of the w/well.
Stainless steel driver side body with full height 54" wide forward and 48" wide rearward compartmentation. Includes (1) 60" wide compartment over the wheel well.
Driver side body with full height 60" wide forward and 54" wide rearward compartmentation. Includes (1) 60" wide compartment over the wheel well. Top mount SS eMAX only.
(2) side low profile stepped interior roof top compartments with extra width to inboard side. Includes hinged raised compartment lids with turn latches,gas shock hold opens and drain line(s) ran to below body. Each lid to have (1) bracket mounted LED light and to be wired to door ajar indicator in cab. Lids shall be without grab handles for lowered OAH and shall have a stepped interior.
Driver half side body with 42" wide forward and 56" wide rearward extended compartmentation. For use with a drop down ladder rack.
Driver side body with upper and lower compartmentation. Includes 42" wide forward and 36" wide rearward lower compartments and (3) opening upper compartments.
Driver side rear mount rescue pumper body with full height 62" wide forward and 42" wide rearward compartmentation. Includes (1) 56" wide compartment over the wheel well and 30 degree angled rear body for improved angle of departure.
Driver side diamond plate roof top compartment. Includes smooth plate painted vertical hinged access door at the rear with D‐Ring latch to be wired to door ajar indicator in cab.
(1) driver side roof top compartment. Includes dual hard suction storage (over/under) accessible through hinged rear panel access door with trigger style latch. Includes (1) bracket mounted LED light and to be wired to door ajar indicator in cab. Includes fixed forward stop for 10' hard suction hoses. Lower hose stop to be positioned for use with a barrel type suction strainer attached.
Stainless steel driver side body with full height 40" wide forward and 40" wide rearward compartmentation. Includes (1) 60" wide compartment over the wheel well.
Driver side body with full height 30" wide forward and 60" wide rearward extended compartmentation. Includes (1) 56" wide compartment over the wheel well.
Stainless steel driver side body with full height 30" front, 40" rear and 60" wide fender panel L2 compartment.
Driver side body with full height 36" wide forward and 56" wide rearward compartmentation. Includes (1) 56" wide compartment over the wheel well. For use on low hosebed body and individual compartments on the driver side.
L1 floor to have a cut‐out rearward and near back wall for a recessed box as applicable to allow for 6000 psi DOT bottle to be located without interference.
PRICE
$25,597.00
$28,458.00
$12,677.00
$11,663.00
$31,135.00
$18,934.00
$5,578.00
$6,135.00
$11,345.00
$14,737.00
$1,618.00
$3,329.00
$27,709.00
$11,494.00
$26,368.00
$14,016.00
$528.00
Option No.
3100‐0409
3100‐0410
3100‐0411
3100‐0412
3100‐0413
3100‐0414
3100‐0415
3100‐0416
3100‐0418
3100‐0419
3100‐0420
3100‐0421
3100‐0422
3100‐0423
3100‐0424
3100‐0425
3100‐0426
Description
(2) driver side roof top compartments. Includes hinged raised compartment lids with turn latches and grab handle(s). Each lid to have (1) bracket mounted ROM V4 LED strip light and to be wired to door ajar indicator in cab.
Driver side body with full height 34" and 30" wide forward compartments and 56" wide rearward compartmentation. Includes (1) 56" wide compartment over the wheel well. Side Mount eMAX
Driver full height side body with (3) full height, rescue style, forward compartments (48" and 30" wide) and (1) rearward compartment (24" wide), (1) upper compartment (56" wide).
Driver side body with full height 42 in. wide forward and 56 in. wide rearward enhanced extended compartmentation. Includes (1) 56 in. wide compartment over the wheel well. L1 compartment to be Rescue Pumper style full depth compartment.
(2) driver side roof top compartments with extra width to inboard side. Compartment top and lids to be smooth plate painted black Durabak. Includes hinged raised compartment lids with turn latches, grab handle(s) and gas shock hold open and drain line(s) ran to below body. Each lid to have (1) bracket mounted LED light and to be wired to door ajar indicator in cab.
Stainless steel driver side body with full height 48" wide forward and 48" wide rearward compartmentation. Includes (1) 60" wide compartment over the wheel well.
(2) driver side roof top compartments. Includes hinged raised compartment lids with turn latches and grab handle(s). Each lid to have (1) bracket mounted ROM V4 LED strip light and to be wired to door ajar indicator in cab.
Driver side body with full height 42in. wide forward and 62in. wide rearward enhanced extended compartmentation. Includes (1) 56in. wide compartment over the wheel well and one (1) storage tunnel.
Driver half side tandem body with 60" wide forward and 48" wide rearward compartmentation.
Driver side body with full height 60" wide forward and 56" wide rearward compartmentation. Includes (1) 56" wide compartment over the wheel well. Rear perimeter or body raised 3" for improved departure angle. Side Mount eMAX only.
Drivers full height side body with 20" wide and 42" wide forward compartments and 42" wide rearward compartment. Includes (1) 56" wide compartments over the wheel well. For use with 30 high lower compt height only.
Driver side body with full height 44" wide forward and 36" wide rearward compartmentation and 60.75" opening. Includes (1) 56" wide compartment over the wheel well and 28.75" opening .
Driver side body with full height 30" wide forward and 50" wide rearward compartmentation. Includes (1) 56" wide compartment over the wheel well. Rescue Pumper individual style compartments.
Driver side body with full height 36" wide forward and 50" wide rearward compartmentation. Includes (1) 56" wide compartment over the wheel well. Rescue Pumper individual style compartments.
Driver half side tandem body with 66" wide forward and 40" wide rearward compartmentation. Includes 50" wide tandem wheel well compartment. SS top cap.
(2) driver side roof top compartments with extra width to inboard side. Includes hinged raised compartment lids with turn latches, grab handle(s) and gas shock hold open and drain line(s) ran to below body. Each lid to have (1) bracket mounted ROM V4 LED strip light and to be wired to door ajar indicator in cab.
Driver side body with full height 60" wide forward and 56" wide rearward compartmentation. Includes (1) 56" wide compartment over the wheel well and one (1) storage tunnel located behind the upper (3) compartment back walls. Top Mount eMAX Only.
PRICE
$3,107.00
$15,458.00
$9,731.00
$13,766.00
$6,831.00
$33,432.00
$3,107.00
$16,420.00
$9,013.00
$13,480.00
$10,227.00
$12,642.00
$11,191.00
$12,101.00
$11,717.00
$5,838.00
$16,399.00
Option No.
3100‐0427
3100‐0428
3100‐0429
3100‐0430
3100‐0431
3100‐0432
3100‐0433
3100‐0434
3100‐0435
3100‐0436
3100‐0437
3100‐0438
3100‐0439
3100‐0440
3100‐0441
3100‐0442
3100‐0443
Description
Driver 3/4 side tandem body with 3/4 full height 42" wide forward, (2) 3/4 compartments over the wheel well, the forward 41.5" wide, rearward to be 61.5" wide, and a 3/4 full height 42" wide rearward compartment. Additionally, there shall be a 3/4 full height 20" wide beavertail compartment.
Drivers full height side body (FOR 4X4 Chassis) with 30" high lower compartment height, (2) lower forward compartments (34" and 28" wide) ahead of wheel well, (1) one lower rearward compartment 24" wide, and (3) upper compartments (48.67" wide x 32" high opening) each, transverse front to rear.
Driver side standard width roof top compartment contents: (2) 6" x 12' hard suction hoses (not included) stored vertical. The hard suction storage shall have a front wall which will prevent the hoses from sliding too far forward while also creating a full depth coffin storage area forward of the wall if applicable.
(2) driver side roof top compartments. Includes hinged raised compartment lids with turn latches and grab handle(s). Each lid to have (1) Amdor LED strip light and to be wired to door ajar indicator in cab.
Driver side tandem body with full height 48" wide forward and 48" wide rearward compartmentation. Includes (2) 51.5" wide compartments over the wheel well.
Stainless steel driver 3/4 side body with 40" wide forward and 58" wide rearward compartmentation rear for flat back body design. Includes (1) 60" wide compartment over the wheel well.
Driver side body with upper and lower compartmentation. Includes 30" wide forward and 50" wide rearward lower compartments and (3) opening upper compartments.
2‐arm ladder rack on driver side. The ladder rack includes amber lights on each end to visually indicate when the rack is in motion. Restricts the top folding step (if optioned) from closing completely. Mounting bracket for lights not required.
Driver side body with full height 26" and 50" wide forward compts, 56" wide over wheel compt and 52" wide rearward compt. Includes slide‐back rear side compt for engine access. HS only.
Stainless steel driver side body with rescue style full height 35" front, 40" rear and 60" wide fender panel L2 compartment.
Driver side body with full height 60" wide forward and 52" wide rearward compartmentation. Includes (1) 56" wide compartment over the wheel well. Includes slide‐back rear side compt for engine access. HS only.
Driver side rear mount rescue pumper body with full height 24" wide forward and 42" wide rearward compartmentation. Includes (1) 56" wide compartment over the wheel well and 30 degree angled rear body for improved angle of departure.
Driver full height side body with (2) full height, rescue style, forward compartments (48" and 30" wide), (2) upper compartment (42" wide) and (1) lower rearward compartment (28").
(2) driver side roof top compartments with extra width to inboard side. Includes hinged raised compartment lids with one (1) L handle style 1/4 turn latche in the center of the compartment top, and two (2) grab handle(s) on each side of the L handle and gas shock hold open and drain line(s) ran to below body. Each lid to have (1) Amdor LED strip light and to be wired to door ajar indicator in cab.
Driver 3/4 side tandem body with full height 42" wide forward and 54" wide rearward compartmentation. Includes (2) 51.5" wide compartments over the wheel well.
The [#LOC] compartment opening width (interior to remain standard) shall be reduce to allow for a single pan door.
Stainless steel driver side body high side 60" front and 60" rear. (4) compartments, tandem axle. For use with single arm overhead portable tank rack
PRICE
$10,490.00
$9,731.00
$346.00
$3,513.00
$14,500.00
$23,976.00
$11,200.00
$12,370.00
$25,597.00
$28,645.00
$24,244.00
$11,647.00
$9,812.00
$6,263.00
$10,570.00
$466.00
$18,980.00
Option No.
3100‐0444
3100‐0445
3100‐0446
3100‐0447
3100‐0448
3100‐0449
3100‐0450
3100‐0451
3100‐0452
3100‐0453
3100‐0454
3100‐0455
3100‐0456
3100‐0457
3100‐0458
3100‐0459
3100‐0460
Description
Driver side body with upper and lower compartmentation. Includes full height 24" wide forward, 30" high by 38" wide lower rear, and 34" high by 38" wide upper rear compartmentation. Includes (1) 56" wide compartment over the wheel well.
Stainless steel driver side body with full height/full depth 54" wide forward and 54" wide rearward compartmentation. Includes (1) 60" wide compartment over the wheel well.
Driver side body with full height 30" wide forward and 52" wide rearward extended compartmentation. Includes (1) 56" wide compartment over the wheel well.
Driver full height side body with 66" wide forward and 42" wide rearward compartmentation. Includes (1) 56" wide compartment over the wheel well. The compartment opening height to be 30" IPO 34". For use with custom chassis only.
(2) driver side roof top compartments for foam pails. Includes hinged compartment lids with turn latches and grab handle(s). Each compartment shall include LED lighting and to be wired to door ajar indicator in cab.
Stainless steel driver side body with full height 48" wide front and 58" rear with reduced upper depth for "T" tank. Includes 60" wide compartment over rear wheels. Upper compartments to be 15" deep.
Stainless steel driver side short Boston style body with low height 48" front and 40" rear and (3) lift‐up doors above. Includes 60" wide fender panel.
Driver side rear mount pumper body with (2) two full height 34" wide forward and (1) one 60" wide rearward compartmentation. Includes (1) 56" wide compartment over the wheel well and provisions to rear mount pump panel in rearward side compartment.
Driver side tandem body with full height 60" wide forward and 54" wide rearward compartmentation. Includes (2) 51.5" wide compartments over the wheel well. Wheel wells and lower compartment height to lowered 4" over standard (Pumper/Rescue Pumper Height).
Driver side body with full height 24" wide forward and 42" wide rearward compartmentation. Includes (1) 56" wide compartment over the wheel well.
Driver side body with full height 28" and 28" wide forward and 52" wide rearward compartmentation. Includes (1) 56" wide compartment over the wheel well. Includes slide‐back rear side compt for engine access. HS only.
Driver side rear mount pumper body with two full height 48" wide forward compartments and 42" wide rearward compartment. Includes (1) 56" wide compartment over the wheel well and 30 degree angled rear body for improved angle of departure.
Driver side tandem body with 48" wide forward and 42" wide rearward compartmentation. Forward compartment to be full height, rearward to be half height.
Driver side body with full height 30" wide forward and 50" wide rearward compartmentation. Includes (1) 56" wide compartment over the wheel well.
Driver side body with full height 42" wide forward and 42" wide rearward compartmentation. Includes (1) 56" wide compartment over the wheel well.
Driver side body with full height 42" (pump panel area the forward 26") and 56" wide forward compartments and 56" wide rearward compartmentation. Includes (1) 56" wide compartment over the wheel well. Side Mount eMAX only. The rearward section of L4 to be transverse with B1/R4 compartments.
Stainless steel driver side body with full height 30" wide forward and 58" wide rearward extended compartmentation. Includes (1) 60" wide compartment over the wheel well
PRICE
$9,902.00
$29,994.00
$11,200.00
$10,004.00
$2,735.00
$28,551.00
$28,458.00
$15,400.00
$15,292.00
$10,336.00
$24,759.00
$18,421.00
$11,106.00
$10,529.00
$11,005.00
$17,222.00
$27,694.00
Option No.
3100‐0461
3100‐0462
3100‐0463
3100‐0464
3100‐0465
3100‐0466
3100‐0467
3100‐0468
3100‐0469
3100‐0470
3100‐0471
3100‐0472
3100‐0473
3100‐0474
3100‐0475
3100‐0476
3100‐0477
Description
Driver side body with full height/full depth 60" wide front and 54" wide rear compartment. Includes (1) 60" wide compartment over the wheel well. Includes notch in upper rear compartment walls to provide for a level hose bed. Side mount SS eMAX only.
Driver side body with full height 60" wide forward and 42" wide rearward compartments. Includes (1) 56" wide compartment over the wheel well. Side Mount e‐MAX only.
Driver full height side body with 31" wide and 31" wide forward compartments and 42" wide rearward compartment. Includes (1) 56" wide compartments over the wheel well.
Driver side body with full height 48" and 30" wide forward and 38" wide rearward non‐transverse extended compartmentation. Includes (1) 56" wide compartment over the wheel well.
Officer side body with full height 48" and 30" wide forward and 38" wide rearward non‐transverse extended compartmentation. Includes (1) 56" wide compartment over the wheel well.
**NARROW BODY** Driver side body with full height 42" wide forward and 56" wide rearward enhanced extended compartmentation. Includes (1) 56" wide compartment over the wheel well.
Roof top compartment contents: (1) 6in x 10ft hard suction hose (not included) stored in the lower area of roof top compartment. Includes stop bracket rear ward of hard suction hose if applicable to body length and partition surround over the hard suction hoses to accommodate storage area above and in front of the stored hose. Floor to include nylon pad as applicable for ease of deployment on scene.
Rear aluminum smooth plate painted job color vertical hinged door on roof top compartment. Includes D‐ring latch and wiring for door ajar switch.
**NARROW BODY** Driver side body with full height 36" wide forward and 36" wide rearward compartmentation. Includes (1) 56" wide compartment over the wheel well.
Stainless steel driver side body with full height, full depth 48" wide forward and 48" wide rearward compartmentation. Includes (1) 60" wide compartment over the wheel well.
Stainless steel driver side body with full height 48" wide forward and 54" wide rearward compartmentation. Includes (1) 60" wide compartment over the wheel well.
Driver side body with full height 30 and 60" wide front and 54" wide rear compartments. Includes (1) 60" wide compartment over the wheel well and one (1) storage tunnel located behind reduced upper depth compartments. SS eMAX only.
(2) driver side roof top compartments. Includes hinged raised compartment lids with turn latches and grab handle(s). Each lid to include LED light (per specifications) and to be wired to door ajar indicator in cab.
Driver side body with full height 36" wide forward and 50" wide rearward enhanced extended compartmentation. Includes (1) 56" wide compartment over the wheel well.
Driver side body with upper and lower compartmentation. Includes 42" wide forward and 56" wide rearward lower compartments and (3) opening upper compartments.
Driver side diamond plate roof top compartment. Includes smooth plate painted vertical hinged access door at the rear with D‐ring style latch to be wired to door ajar indicator in cab.
Stainless steel driver side body with full height 30" wide forward and 46" wide rearward compartmentation having Lord/coil spring torsion style body mounts. Includes a 60" wide compartment over the wheel well. Custom height in lower L3 for a special ALS shelving unit.
PRICE
$16,678.00
$12,636.00
$10,227.00
$12,403.00
$12,403.00
$12,677.00
$701.00
$222.00
$10,297.00
$29,343.00
$29,122.00
$21,676.00
$2,529.00
$11,907.00
$12,642.00
$1,592.00
$26,045.00
Option No.
3100‐0478
3100‐0479
3100‐0480
3100‐0481
3100‐0482
3100‐0483
3100‐0484
3100‐0485
3100‐0486
3100‐0487
3100‐0488
3100‐0489
3100‐0490
3100‐0491
3100‐0492
3100‐0493
Description
Driver side body with full height 36" wide forward and 42" wide rearward compartmentation. Includes (1) 56" wide compartment over the wheel well and one (1) storage tunnel.
Stainless steel 96" wide driver side body with full height, full depth 48" wide forward and 48" wide rearward compartmentation. Includes (1) 54" wide compartment over the wheel well.
Driver side body with full height 30" wide forward and 52" wide rearward enhanced extended compartmentation. Includes (1) 56" wide compartment over the wheel well.
Driver side tandem body with (2) full height 28" wide forward and 54" wide rearward compartmentation. Includes (2) 51.5" wide compartments over the wheel well.
Driver side body with 19.5in. wide forward and 31in. wide rearward compartmentation. Includes (1) 40in. wide compartment over the wheel well. Compartment tops raised approximately 6in. to match hosebed height. Rear of body under rearward compartment shall be raised 4in. or as applicable to allow for additional departure angle.
Stainless steel driver side body with full height/full depth 36" wide front compartment and reduced depth upper 48" rearward compartmentation. Includes 60" wide compartment above rear wheels.
Stainless steel driver side body with full height 44" wide forward and 60" wide rearward compartmentation. Includes (1) 54" wide compartment over the wheel well.
Driver side body with full height 34" and 56" wide forward compartments and 56" wide rearward compartmentation. Includes (1) 56" wide compartment over the wheel well. Side Mount eMAX only.
Driver side tandem body with full height 54" wide forward and 48" wide rearward compartmentation. Includes (2) 51.5" wide compartments over the wheel well. Includes 30" high lower compartment height "Pumper Style" ilo 34" high. Side Dumps between or adjacent to Tandems are not available.
Stainless steel driver side body with full height, full depth 48" wide forward and 58" wide rearward enhanced extended compartmentation. Includes (1) 60" wide compartment over the wheel well. Compartment height to be 78".
2‐arm ladder rack on driver side. The ladder rack includes amber lights on each end to visually indicate when the rack is in motion. Restricts the top folding step (if optioned) from closing completely. Includes mounting bracket (if required, matching rear compartment face or compartment wrap finish) for components mounted on rear compartment face.
Stainless steel driver side body with full height 30" wide forward and 46" wide rearward compartmentation having Lord/coil spring torsion style body mounts. Includes a 66" wide compartment over the wheel well. Custom height in lower L3 for a special ALS shelving unit.
Driver side body with full height 60" wide forward and 46" wide rearward compartmentation. Includes (1) 56" wide compartment over the wheel well. Top Mount eMAX Only.
Driver side body with full height 36" wide forward and 56" wide rearward enhanced extended compartmentation. Includes (1) 56" wide compartment over the wheel well.
Driver half side body with 36" wide forward and 50" wide rearward enhanced extended compartmentation. Includes adjustable ladder tracks.
Stainless steel driver side body with full height 48" wide front and 48" wide rear compartments. Includes 60" wide compartment over rear wheels.
PRICE
$14,691.00
$29,343.00
$11,200.00
$15,792.00
$10,671.00
$28,735.00
$30,894.00
$15,499.00
$15,292.00
$29,738.00
$12,370.00
$26,045.00
$12,878.00
$11,535.00
$6,060.00
$28,150.00
Option No.
3100‐0494
3100‐0495
3100‐0496
3100‐0497
3100‐0498
3100‐0499
3100‐0500
3100‐0501
3100‐0502
3100‐0503
3100‐0505
3100‐0506
3100‐0507
3100‐0508
3100‐0509
Description
Stainless steel driver side body with full height/full depth 40" wide forward and 58" wide rearward extended compartment. Includes (1) 60" wide compartment over the wheel well.
Driver side tandem body with two forward compartments ahead of the rear wheels, and one rear compartment behind rear wheels. The forward front compartment to be 38" wide and full height, the rearward front compartment to be 24" wide and half height. The single rear to be a half height 60" wide compartment.
Stainless steel driver side body with full height 35" wide forward and 48" wide rearward compartmentation. Includes (1) 60" wide compartment over the wheel well.
Rear aluminum smooth plate painted job color vertical hinged door on driver side roof top compartments. Includes D‐Ring latch and wiring for door ajar switch.
Driver side roof top compartment contents: (1) 6" x 10' hard suction hose (not included) stored in lower rearward area of the roof top storage with Nylatron compartment flooring. Includes surround forward and above hard suction hose to allow for additional storage in remaining available roof top storage compartments accessible from top lift doors.
Driver side tandem body with full height 66" wide forward and 60" wide rearward compartmentation. Includes (2) 51.5" wide compartments over the wheel well.
Driver side body with upper and lower compartmentation. Includes 42" wide forward and 48" wide rearward lower compartments and (3) opening upper compartments.
(2) driver side roof top compartments with extra width to inboard side. Custom sized to store hydraulic reels. Includes hinged raised compartment lids with turn latches, grab handle(s) and gas shock hold open and drain line(s) ran to below body. Each lid to have (1) bracket mounted LED light and to be wired to door ajar indicator in cab.
Driver side body with full height 52" wide forward and 56" wide rearward compartmentation. Includes (1) 56" wide compartment over the wheel well. Side Mount eMAX only.
(2) driver side roof top compartments with extra width to inboard side. Includes hinged raised compartment lids with one (1) ' L' handle style 1/4 turn latch in the center of the compartment top, two (2) grab handle(s) on each side of the' L' handle, gas shock hold open and drain line(s) ran to below body. Each lid to have (1) Amdor LED strip light and to be wired to door ajar indicator in cab.
Driver side body with full height 42" wide forward and 56" wide rearward enhanced extended compartmentation. Includes (1) 56" wide compartment over the wheel well and one (1) storage tunnel.
Driver side body with full height 35" wide forward and 47" wide rearward compartmentation. Includes (1) 56" wide compartment over the wheel well.
(3) driver side roof top compartments with extra width to inboard side (43"/43"/43"). Includes hinged raised compartment lids with thumb latches, grab handle(s) and gas shock hold open and drain line(s) ran to below body. Each lid to have (1) bracket mounted LED light and to be wired to door ajar indicator in cab.
Driver side body with full height 42" wide forward and 56" wide rearward enhanced extended compartmentation. Includes (1) 56" wide compartment over the wheel well.
Stainless steel driver side 3/4 side body with full height 40" wide forward and 48" wide rearward compartmentation. Includes (1) 54" wide compartment over the wheel well.
PRICE
$27,694.00
$15,292.00
$28,645.00
$266.00
$719.00
$16,866.00
$11,839.00
$5,466.00
$12,620.00
$6,263.00
$15,596.00
$13,540.00
$6,392.00
$11,922.00
$23,949.00
Option No.
3100‐0510
3100‐0511
3100‐0512
3100‐0513
3100‐0514
3100‐0515
3100‐0516
3100‐0517
3100‐0518
3100‐0519
3100‐0520
3100‐0521
3100‐0522
3100‐0523
3100‐0524
3100‐0525
3100‐0526
Description
Driver side tandem body with 60" wide full height forward compartment. Rearward of the forward compartment to 3/4 height with 54" wide rearward compartmentation. Includes (2) 51.5" wide compartments over the wheel well.
Stainless steel driver side body with full height full depth 48" wide forward and 48" wide rearward compartmentation. Includes (1) 60" wide compartment over the wheel well.
Vertical partition located in driver side roof top compartment at rear access door. Partition is to be full height of compartment and 61" long capped of at the end to create a boxed in area for separate storage.
Driver half side tandem body with (1) 44" wide first forward, (1) 30" wide second forward and (1) 66" wide rearward compartments. Compartment height openings to be 30" IPO standard 34".
Driver side body with full height 40" wide forward and 56" wide rearward compartmentation. Includes (1) 56" wide compartment over the wheel well.
Stainless steel driver side body with full height 40" wide forward and 48" wide rearward compartmentation. Includes (1) 60" wide compartment over the wheel well.
Driver side body with full height 42" wide forward and 56" wide rearward enhanced extended compartmentation. Includes (1) 56" wide compartment over the wheel well.
Compartment L1 to be notched for vertical exhaust in back forward corner of the compartment.
(2) side roof top compartments with extra width to inboard side. Includes hinged raised compartment lids with D‐ring slam style latch (s) and no grab handles for reduced OAH impact, with gas shock hold open(s) and drain line(s) ran to below body. Each lid to have (1) bracket mounted LED light and to be wired to door ajar indicator in cab.
Driver side body with full height 36" wide forward and 56" wide rearward compartmentation. Includes (1) 56" wide compartment over the wheel well.
Driver side body with full height 72" wide forward and 60" wide rearward compartmentation. Includes (1) 56" wide compartment over the wheel well. Includes provision for pump panel. Rear Mount Pumper Body only.
Driver side body with upper and lower compartmentation. Includes 24" wide forward and 36" wide rearward lower compartments and (2) opening upper compartments. For use with 94"(96" with rubrail) wide body configuration.
Flat back Driver side body with full height 48" wide forward and 56" wide rearward compartmentation. Includes (1) 56" wide compartment over the wheel well.
Driver side body with full height 26" and 56" wide forward compartments and 56" wide rearward compartmentation. Includes (1) 56" wide compartment over the wheel well. eMax Only.
(2) driver side roof top compartments with extra width to inboard side. Includes hinged raised compartment lids with D‐Ring latches, no grab handle(s) and gas shock hold open and drain line(s) ran to below body. Each lid to have (1) bracket mounted ROM V4 LED strip light and to be wired to door ajar indicator in cab.
Driver side body with full height 42" wide forward and 56" wide rearward extended compartmentation. Includes (1) 56" wide compartment over the wheel well.
(2) driver side roof top compartments with extra width to inboard side. Includes hinged raised compartment lids with turn latches, grab handle(s) and gas shock hold open and drain line(s) ran to below body. Each lid to be wired to door ajar indicator in cab. Special 24" interior depth.
PRICE
$12,600.00
$28,858.00
$483.00
$12,174.00
$12,597.00
$27,806.00
$11,922.00
$289.00
$5,466.00
$11,872.00
$16,400.00
$9,434.00
$13,280.00
$14,885.00
$6,036.00
$12,677.00
$5,330.00
Option No.
3100‐0527
3100‐0528
3100‐0529
3100‐0530
3100‐0531
3100‐0532
3100‐0533
3100‐0534
3100‐0535
3105‐0001
3105‐0002
3105‐0004
3105‐0005
3105‐0006
3105‐0007
3105‐0008
3105‐0009
Description
Stainless steel driver side body with full height/full depth 48" wide forward and 60" wide rearward compartmentation. Includes (1) 60" wide compartment over the wheel well. Special 69" high rescue pumper body height.
Stainless steel driver side body with full height 30" wide forward and 58" wide rearward enhanced extended compartmentation. Includes (1) 60" wide compartment over the wheel well.
Driver high side stainless steel body with 60" front and 60" rear. (4) compartments, tandem axle.
Stainless steel driver side body with full height full depth 48" wide forward and 58" wide rearward compartmentation. Includes (1) 60" wide compartment over the wheel well.
Stainless steel driver side body with full height 30" wide forward and 46" wide rearward compartmentation. NOTE: Standard Lord mount body mounting system. Includes a 60" wide compartment over the wheel well. Custom height in lower L3 for a special ALS shelving unit. No upper hose bed side sheet on the driver side of the body providing a finished overall body height of 70".
Driver side body with upper and lower compartmentation. Includes lower 48" wide forward and full height 48" wide rearward compartments and (2) opening upper compartments.
The L3 compartment to be transverse into L4.
(2) driver side roof top compartments with extra width to inboard side. Includes hinged raised compartment lids with D‐ring latches, grab handle(s) and gas shock hold open and drain line(s) ran to below body. Each lid to have (1) bracket mounted LED light and to be wired to door ajar indicator in cab.
Driver side body with full height 60in. wide forward and 56in. wide rearward extended compartment. Includes (1) 56in. wide compartment over the wheel well.
Enhanced extended forward compartmentation for Rescue Pumper. Includes 14" of additional interior width to the forward side compartments and 25" of additional depth in the forward 14" wide section (as applicable). Overall interior height will vary depending on additional option selections.
Rear Mount forward body. Includes main side body structures and compartment L1/R1, L2/R2.
Rear Mount forward body compartments. Includes L1/R1 48" wide x 26" deep in the 56" lower area and 12" deep in the 12" upper area, L2/R2 56" wide x 26" deep in the 22" lower area and 12" deep in the 12" upper area.
Hosebed walkway. Includes forward body headboard mod and rear body module walkway end partition. Walkway to be a slip resistant material. Walkway located to [#LOC] of the hosebed.
Rear Mount forward body compartments. Includes L1/R1 54" wide x 26" deep in the 56" lower area and 12" deep in the 12" upper area, L2/R2 56" wide x 26" deep in the 22" lower area and 12" deep in the 12" upper area.
Rear Mount forward body compartments with officer side Zico Overhead Ladder Rack. Includes L1/R1 ‐ 48" wide x 26" deep in the 56" lower area and 12" deep in the 12" upper area, L2 ‐ 56" wide x 26" deep in the 22" lower area and 12" deep in the 12" upper area, R2 ‐ 33" wide x 26" deep in the 22" lower area and 12" deep in the 12" upper area (position of R2 depends on position of overhead ladder rack).
Rear Mount forward body. Includes main side body structures and compartment L1/R1, L2/R2 and a Zico overhead ladder rack (control located officer rear body/pump module).
Rear Mount forward body compartments with driver side storage tunnel. Includes L1 ‐ 72" wide x 26" deep in the 30" lower area and 12" deep in the 34" upper area, L2 ‐ 56" wide x 12" deep, R1 ‐ 72" wide x 26" deep in the 56" lower area and 12" deep in the 12" upper area, R2 ‐ 56" wide x 26" deep in the 22" lower area and 12" deep in the 12" upper area.
PRICE
$29,994.00
$27,145.00
$18,902.00
$28,951.00
$26,045.00
$12,224.00
$280.00
$5,569.00
$13,225.00
$2,283.00
$15,539.00
$0.00
$1,925.00
$1,539.00
$0.00
$24,742.00
$4,536.00
Option No.
3105‐0010
3105‐0011
3105‐0013
3105‐0014
3105‐0015
3105‐0016
3105‐0017
3105‐0018
3105‐0019
3105‐0020
3105‐0021
Description
Rear Mount forward body. Includes main side body structures and compartment LT/RT, L1/R1, L2/R2. LT/RT (full width and 95" high) with lower storage areas (compartment opening 67" wide and same height as main body compartments). Includes full width forward storage pan and a pan in the rearward center/officer area between the driver roof top compartment. Transverse floor to run full width. Rear headboard to have area for routing of plumbing for preconnects located in rearward area. Area above preconnects (forward area) to be for storage of a stokes basket. L1/R1 54" wide x 26" deep in the 56" lower area and 12" deep in the 12" upper area, L2/R2 56" wide x 26" deep in the 22" lower area and 12" deep in the 12" upper area.
Rear Mount forward body compartments with driver side storage tunnel. Includes L1 ‐ 54" wide x 26" deep in the 30" lower area and 12" deep in the 38" upper area, L2 ‐ 56" wide x 12" deep. R1 ‐ 54" wide x 26" deep in the 56" lower area and 12" deep in the 12" upper area, R2 ‐ 56" wide x 26" deep in the 22" lower area and 12" deep in the 12" upper area.
Rear Mount forward body compartments. Includes L1 ‐ 48" wide x 26" deep in the 56" lower area and 12" deep in the 12" upper area, L2 ‐ 56" wide x 26" deep in the 22" lower area and 12" deep in the 12" upper area, R1 ‐ 48" wide x 26" deep in the 30" lower area and 12" deep in the 38" upper area and R2 ‐ 56" wide x 12" deep x 34 high.
Rear Mount forward body compartments. Includes L1/R1 ‐ 60" wide x 26" deep in the 56" lower area and 12" deep in the 12" upper area, L2/R2 ‐ 56" wide x 26" deep in the 22" lower area and 12" deep in the 12" upper area.
Rear Mount forward body compartments. Includes L1/R1 ‐ 66" wide x 26" deep in the 56" lower area and 12" deep in the 12" upper area, L2/R2 ‐ 56" wide x 26" deep in the 22" lower area and 12" deep in the 12" upper area.
Rear Mount forward body compartments. Includes L1/R1 ‐ 72" wide x 26" deep in the 56" lower area and 12" deep in the 12" upper area, L2/R2 ‐ 56" wide x 26" deep in the 22" lower area and 12" deep in the 12" upper area.
Rear Mount forward body compartments with officer side Zico Overhead Ladder Rack. Includes L1/R1 ‐ 54" wide x 26" deep in the 56" lower area and 12" deep in the 12" upper area, L2 ‐ 56" wide x 26" deep in the 22" lower area and 12" deep in the 12" upper area, R2 ‐ 33" wide x 26" deep in the 22" lower area and 12" deep in the 12" upper area (position of R2 depends on position of overhead ladder rack).
Rear Mount forward body compartments with officer side Zico Overhead Ladder Rack. Includes L1/R1 ‐ 60" wide x 26" deep in the 56" lower area and 12" deep in the 12" upper area, L2 ‐ 56" wide x 26" deep in the 22" lower area and 12" deep in the 12" upper area, R2 ‐ 33" wide x 26" deep in the 22" lower area and 12" deep in the 12" upper area (position of R2 depends on position of overhead ladder rack).
Rear Mount forward body compartments with officer side Zico Overhead Ladder Rack. Includes L1/R1 ‐ 66" wide x 26" deep in the 56" lower area and 12" deep in the 12" upper area, L2 ‐ 56" wide x 26" deep in the 22" lower area and 12" deep in the 12" upper area, R2 ‐ 33" wide x 26" deep in the 22" lower area and 12" deep in the 12" upper area (position of R2 depends on position of overhead ladder rack).
Rear Mount forward body compartments with officer side Zico Overhead Ladder Rack. Includes L1/R1 ‐ 72" wide x 26" deep in the 56" lower area and 12" deep in the 12" upper area, L2 ‐ 56" wide x 26" deep in the 22" lower area and 12" deep in the 12" upper area, R2 ‐ 33" wide x 26" deep in the 22" lower area and 12" deep in the 12" upper area (position of R2 depends on position of overhead ladder rack).
Rear Mount forward body compartments with driver side storage tunnel. Includes L1 ‐ 48" wide x 26" deep in the 30" lower area and 12" deep in the 38" upper area, L2 ‐ 56" wide x 12" deep. R1 ‐ 48" wide x 26" deep in the 56" lower area and 12" deep in the 12" upper area, R2 ‐ 56" wide x 26" deep in the 22" lower area and 12" deep in the 12" upper area.
PRICE
$31,653.00
$1,539.00
$0.00
$2,539.00
$3,539.00
$4,536.00
$1,539.00
$2,539.00
$3,539.00
$4,536.00
$0.00
Option No.
3105‐0022
3105‐0023
3105‐0024
3105‐0025
3105‐0026
3105‐0027
3105‐0028
3105‐0029
3105‐0030
3105‐0031
3105‐0032
3105‐0033
3105‐0034
3105‐0035
Description
Rear Mount forward body compartments with driver side storage tunnel. Includes L1 ‐ 60" wide x 26" deep in the 30" lower area and 12" deep in the 38" upper area, L2 ‐ 56" wide x 12" deep. R1 ‐ 60" wide x 26" deep in the 56" lower area and 12" deep in the 12" upper area, R2 ‐ 56" wide x 26" deep in the 22" lower area and 12" deep in the 12" upper area.
Rear Mount forward body compartments with driver side storage tunnel. Includes L1 ‐ 66" wide x 26" deep in the 30" lower area and 12" deep in the 38" upper area, L2 ‐ 56" wide x 12" deep. R1 ‐ 66" wide x 26" deep in the 56" lower area and 12" deep in the 12" upper area, R2 ‐ 56" wide x 26" deep in the 22" lower area and 12" deep in the 12" upper area.
Rear Mount forward body compartments with officer side storage tunnel. Includes L1 ‐ 48" wide x 26" deep in the 56" lower area and 12" deep in the 12" upper area, L2 ‐ 56" wide x 26" deep in the 22" lower area and 12" deep in the 12" upper area. R1 ‐ 48" wide x 26" deep in the 30" lower area and 12" deep in the 38" upper area, R2 ‐ 56" wide x 12" deep.
Rear Mount forward body compartments with officer side storage tunnel. Includes L1 ‐ 54" wide x 26" deep in the 56" lower area and 12" deep in the 12" upper area, L2 ‐ 56" wide x 26" deep in the 22" lower area and 12" deep in the 12" upper area. R1 ‐ 54" wide x 26" deep in the 30" lower area and 12" deep in the 38" upper area, R2 ‐ 56" wide x 12" deep.
Rear Mount forward body compartments with officer side storage tunnel. Includes L1 ‐ 60" wide x 26" deep in the 56" lower area and 12" deep in the 12" upper area, L2 ‐ 56" wide x 26" deep in the 22" lower area and 12" deep in the 12" upper area. R1 ‐ 60" wide x 26" deep in the 30" lower area and 12" deep in the 38" upper area, R2 ‐ 56" wide x 12" deep.
Rear Mount forward body compartments with officer side storage tunnel. Includes L1 ‐ 66" wide x 26" deep in the 56" lower area and 12" deep in the 12" upper area, L2 ‐ 56" wide x 26" deep in the 22" lower area and 12" deep in the 12" upper area. R1 ‐ 66" wide x 26" deep in the 30" lower area and 12" deep in the 38" upper area, R2 ‐ 56" wide x 12" deep.
Rear Mount forward body compartments with officer side storage tunnel. Includes L1 ‐ 72" wide x 26" deep in the 56" lower area and 12" deep in the 12" upper area, L2 ‐ 56" wide x 26" deep in the 22" lower area and 12" deep in the 12" upper area. R1 ‐ 72" wide x 26" deep in the 30" lower area and 12" deep in the 38" upper area, R2 ‐ 56" wide x 12" deep.
Rear Mount forward body compartments w/dual storage tunnels. Includes L1/R1 ‐ 48" wide x 26" deep in the 30" lower area and 12" deep in the 38" upper area, L2/R2 ‐ 56" wide x 12" deep.
Rear Mount forward body compartments w/dual storage tunnels. Includes L1/R1 ‐ 54" wide x 26" deep in the 30" lower area and 12" deep in the 38" upper area, L2/R2 ‐ 56" wide x 12" deep.
Rear Mount forward body compartments w/dual storage tunnels. Includes L1/R1 ‐ 60" wide x 26" deep in the 30" lower area and 12" deep in the 38" upper area, L2/R2 ‐ 56" wide x 12" deep.
Rear Mount forward body compartments w/dual storage tunnels. Includes L1/R1 ‐ 66" wide x 26" deep in the 30" lower area and 12" deep in the 38" upper area, L2/R2 ‐ 56" wide x 12" deep.
Rear Mount forward body compartments w/dual storage tunnels. Includes L1/R1 ‐ 72" wide x 26" deep in the 30" lower area and 12" deep in the 38" upper area, L2/R2 ‐ 56" wide x 12" deep.
Rear Mount forward body. Includes main side body structures and compartment L1/R1, L2/R2 and (1) storage tunnel.
Rear Mount forward body. Includes main side body structures and compartment L1/R1, L2/R2 and (2) storage tunnels.
PRICE
$2,539.00
$3,539.00
$0.00
$1,539.00
$2,539.00
$3,539.00
$4,536.00
$0.00
$1,539.00
$2,539.00
$3,539.00
$4,536.00
$21,521.00
$26,062.00
3105‐0042
Description
Rear Mount forward body. Includes main side body structures and compartment LT/RT, L1/R1, L2/R2. LT/RT (full width and 95" high) with lower storage areas (compartment opening 67" wide and same height as main body compartments). Includes full width storage pan. Transverse floor to run full width. Rear headboard to have area for routing of plumbing for preconnects located in rearward area. The speedlay area to be stacked style and offset to rearward area of the transverse compartment. The upper speedlay area to hold (2) speedlay trays: (1) to hold ‐ 200' of 2.5" DJ hose and (1) dry lay to hold ‐ 100' of 1.75" DJ hose and 100' of 2.5" DJ hose. The lower speedlay area to hold (3) speedlay trays: (2) to hold 200' of 1.75" DJ hose each and (1) to hold 100' of 1.75" DJ hose. L1/R1 54" wide x 26" deep in the 56" lower area and 12" deep in the 12" upper area, L2/R2 56" wide x 26" deep in the 22" lower area and 12" deep in the 12" upper area.
Transverse module (full width and height of the body) located forward of the body. Includes single 30" wide compartment opening per side (with a shallow lower area and a transverse upper area with full width smooth plate flooring). Upper area of transverse module to have diamond plate dunnage pan.
Transverse module (full width and height of the body) located forward of the body. Includes single 36" wide compartment opening per side (with a shallow lower area and a transverse upper area with full width smooth plate flooring). Upper area of transverse module to have diamond plate dunnage pan.
Transverse module (full width and height of the body) located forward of the body. Includes single 42" wide compartment opening per side (with a shallow lower area and a transverse upper area with full width smooth plate flooring). Upper area of transverse module to have diamond plate dunnage pan.
Transverse module (full width and height of the body) located forward of the body. Includes single 50" wide compartment opening per side (with a shallow lower area and a transverse upper area with smooth plate flooring). Rearward transverse compartment area to have double preconnects with removable trays (side by side) and backboard storage (rearward of preconnects with velcro straps). Upper area of transverse module to have diamond plate dunnage pan.
Transverse module (full width and height of the body) located forward of the body. Includes single 56" wide compartment opening per side (with a shallow lower area and a transverse upper area with smooth plate flooring). Rearward transverse compartment area to have double preconnects with removable trays (side by side) and backboard storage (rearward of preconnects with velcro straps). Upper area of transverse module to have diamond plate dunnage pan.
Transverse module (full width and height of the body) located forward of the body. Includes single 62" wide compartment opening per side (with a shallow lower area and a transverse upper area with smooth plate flooring). Rearward transverse compartment area to have double preconnects with removable trays (side by side) and backboard storage (rearward of preconnects with velcro straps). Upper area of transverse module to have diamond plate dunnage pan.
3105‐0043
Transverse module (full width and height of the body) located forward of the body. Includes single 50" wide compartment opening per side (with a shallow lower area and a transverse upper area with smooth plate flooring). Rearward transverse compartment area to have triple preconnects with removable trays (side by side). Upper area of transverse module to have diamond plate dunnage pan.
$13,369.00
3105‐0044
Transverse module (full width and height of the body) located forward of the body. Includes single 56" wide compartment opening per side (with a shallow lower area and a transverse upper area with smooth plate flooring). Rearward transverse compartment area to have triple preconnects with removable trays (side by side). Upper area of transverse module to have diamond plate dunnage pan.
$14,907.00
Option No.
3105‐0036
3105‐0037
3105‐0038
3105‐0039
3105‐0040
3105‐0041
PRICE
$31,653.00
$11,565.00
$13,103.00
$14,641.00
$12,918.00
$14,456.00
$15,994.00
Option No.
Description
3105‐0045
Transverse module (full width and height of the body) located forward of the body. Includes single 62" wide compartment opening per side (with a shallow lower area and a transverse upper area with smooth plate flooring). Rearward transverse compartment area to have triple preconnects with removable trays (side by side). Upper area of transverse module to have diamond plate dunnage pan.
$16,445.00
3105‐0046
Transverse module (full width and height of the body) located forward of the body. Includes single 50" wide compartment opening per side (with a shallow lower area and a transverse upper area with smooth plate flooring). Rearward transverse compartment area to have double preconnects with removable trays (stacked). Upper area of transverse module to have diamond plate dunnage pan.
$13,223.00
3105‐0047
Transverse module (full width and height of the body) located forward of the body. Includes single 56" wide compartment opening per side (with a shallow lower area and a transverse upper area with smooth plate flooring). Rearward transverse compartment area to have double preconnects with removable trays (stacked). Upper area of transverse module to have diamond plate dunnage pan.
$14,760.00
3105‐0053
3105‐0054
Transverse module (full width and height of the body) located forward of the body. Includes single 62" wide compartment opening per side (with a shallow lower area and a transverse upper area with smooth plate flooring). Rearward transverse compartment area to have double preconnects with removable trays (stacked). Upper area of transverse module to have diamond plate dunnage pan.
Preconnect module (stacked) for use with aluminum speedlay trays. Includes area for (2) stacked preconnect, lower storage compartments with push button latches, running boards and upper area dunnage pan.
Preconnect module (stacked). Includes area for (2) stacked preconnects, (1) upper preconnect, lower storage compartments with push button latches and running boards.
Preconnect module to be capable of holding the following contents: Upper preconnect area to hold (1) 400' of 1.75" DJ with removable tray. Lower preconnect area to hold (1) 400' of 1.75" DJ with removable tray.
Preconnect module to be capable of holding the following contents: Upper preconnect area to hold (2) 200' of 1.75" DJ with removable trays. Lower preconnect area to hold 200' of 2.5" DJ with removable tray.
Preconnect module to be capable of holding the following contents: Upper preconnect area to hold (2) 200' of 1.75" DJ with removable trays. Lower preconnect area to hold (2) 200' of 1.75" DJ with removable trays.
Rear Mount forward body. Includes main side body structures and compartment L1/R1, L2/R2.
3105‐0055
Rear Mount Body Assembly. Includes driver side, officer side and rear end assemblies. Driver side body with full height 48" wide forward and 60" wide rearward compartmentation. Includes (1) 56" wide compartment over the wheel well. Officer side body with full height 48" wide forward and 60" wide rearward compartmentation. Includes (1) 56" wide compartment over the wheel well and one (1) storage tunnel. Rear end for rear mount pump application. Includes smooth plate panels and storage access door with push button latch.
3105‐0056
Preconnect module (stacked). Includes area for (2) stacked preconnect, lower storage compartments with push button latches, running boards, upper area dunnage pan and horizontal backboard storage with drop down diamond plate access door (wired to door ajar).
3105‐0048
3105‐0049
3105‐0050
3105‐0051
3105‐0052
PRICE
$16,298.00
$11,565.00
$0.00
$904.00
$1,354.00
$1,806.00
$20,487.00
$31,641.00
$8,556.00
Option No.
3105‐0057
3105‐0058
3105‐0059
3105‐0060
3105‐0061
3105‐0062
3105‐0063
3105‐0066
3105‐0067
3105‐0068
3105‐0069
3105‐0070
Description
Preconnect/Transverse module (full width and height of body). Includes (2) full width stacked speedlays (make standard size opening as used on normal width speedlay module). Each speedlay to be plumbed for use with 1.75" DJ hose. Area directly behind speedlays to have a transverse compartment (opening height to match body compartments). Transverse to include full width floor. Upper area to include a full width storage pan (forward of roof top compartments) and (1) pan located between the roof top compartments. Make pans as deep as practical.
Transverse module (full width and height of the body) located forward of the body. Includes single 30" wide compartment opening per side (with a shallow lower area and a transverse upper area with smooth plate flooring). Lower transverse compartment area to have triple preconnects with removable trays (side by side). Above the speedlay area to be storage for stokes basket. Upper area of transverse module to have diamond plate dunnage pan.
The outboard panels of the full width transverse module to be smooth plate overlays. These areas are to be seamless and painted job color.
Transverse module (full width and height of the body) located forward of the body. Includes single 30" wide compartment opening per side (with a shallow lower area and a transverse upper area with smooth plate flooring). Rearward transverse compartment area to have triple preconnects with removable trays (stacked, (2) 1.5" on top and (1) 2.5" on bottom). Upper area of transverse module to have diamond plate dunnage pan.
Backboard storage sleeve with retaining strap. Located in LT/RT compartment forward of the speedlays to be 5" wide x 20" high.
Rear Mount body. Includes main side body structures and compartments L1/R1, L2/R2, L3/R3 and L4/R4. Includes interior compartment offset for pump panel location and mounting, rear body structure for rear mounted pump application.
Rear Mount forward body compartments. Includes L1 ‐ 32" wide x 26" deep in the 56" lower area and 12" deep in the 12" upper area, R1 ‐ 36" wide x 26" deep in the 56" lower area and 12" deep in the 12" upper area, L2/R2 ‐ 48" wide x 26" deep in the 56" lower area and 12" deep in the 12" upper area, L3/R3 ‐ 56" wide x 26" deep in the 22" lower area and 12" deep in the 12" upper area, L4 ‐ (pump panel location) ‐ 60" wide x 68" high x 12" deep and R4 ‐ 60" wide x 68" high x 12" deep.
Rear Mount forward body compartments. Includes L1/R1 ‐ 72" wide x 26" deep in the 56" lower area and 12" deep in the 12" upper area, L2/R2 ‐ 56" wide x 26" deep in the 22" lower area and 12" deep in the 12" upper area. An externally‐mounted compartment top shall be provided and constructed of a 1/8" (.125") aluminum smooth plate with black Scorpion coating (IPOS diamond plate).
Transverse module (full width and height of the body) located forward of the body. Includes single 30" wide compartment opening per side (with a shallow lower area and a transverse upper area with smooth plate flooring). Rearward transverse compartment area to have triple preconnects with removable trays (stacked, (2) 1.5" on top and (1) 2.5" on bottom). Upper area of transverse module to have a dunnage pan made of aluminum smooth plate with black Scorpion coating (IPOS diamond plate). The running boards shall be constructed of aluminum smooth plate with black Scorpion coating (IPOS diamond plate)
Preconnect module to be capable of holding the following contents: Upper preconnect area to hold (2) 200' of 1.75" DJ with removable poly trays. Lower preconnect area to hold 200' of 2.5" DJ with removable poly tray.
Preconnect module (stacked)for use with Poly trays. Includes area for (2) stacked preconnect, lower storage compartments with push button latches, running boards and upper area dunnage pan.
Rear Mount body. Includes main side body structures and compartments L1/R1, L2/R2, L3/R3 and L4/R4. Includes interior compartment offset for pump panel location and mounting, rear body structure for rear mounted pump application.
PRICE
$10,844.00
$12,152.00
$316.00
$13,369.00
$982.00
$37,866.00
$0.00
$4,885.00
$13,977.00
$1,354.00
$12,047.00
$0.00
Option No.
3105‐0071
3105‐0072
3105‐0073
3105‐0074
3105‐0075
3105‐0076
3105‐0077
3105‐0078
3105‐0079
3105‐0080
3110‐0000
3110‐0001
3110‐0002
3110‐0003
3110‐0004
3110‐0005
3110‐0006
Description
Rear Mount forward body compartments. Includes L1/R1 ‐ 44" wide x 26" deep in the 56" lower area and 12" deep in the 12" upper area, L2/R2 ‐ 44" wide x 26" deep in the 56" lower area and 12" deep in the 12" upper area, L3/R3 ‐ 56" wide x 26" deep in the 22" lower area and 12" deep in the 12" upper area, L4 ‐ (pump panel location upper section) ‐ 46" wide x 24" high x 24" deep in the lower section and R4 ‐ 46" wide x 24" deep in the 56" lower area and 12" deep in the 12" upper area.
Transverse module (full width and height of the body) located forward of the body. Includes single 24" wide compartment opening per side (with a shallow lower area and a transverse upper area with full width smooth plate flooring). Upper area of transverse module to have diamond plate dunnage pan.
Backboard storage sleeve with retaining strap(s). Located in LT/RT compartment in transverse area horizontally mounted. 5"H x 22"W x 76"L.
Transverse module (full width and height of the body) located forward of the body. Includes single 24" wide compartment opening per side (with a shallow lower area and a transverse upper area with full width smooth plate flooring). Upper area of transverse module to have diamond plate dunnage pan.
Preconnect module (stacked). Includes area for (2) preconnect, (1) transverse storage area, lower storage compartments with push button latches, running boards, upper area dunnage pan and horizontal backboard storage with drop down diamond plate access door (wired to door ajar).
Transverse module (full width and height of the body) located forward of the body. Includes single 32" wide compartment opening per side (with a shallow lower area and a transverse upper area with full width smooth plate flooring). Upper area of transverse module to have diamond plate dunnage pan.
A pre‐connect storage area will be located inside the transverse module towards the rear that will accommodate double pre‐connects with removable trays (trays listed separately).
Transverse module (full width and height of the body) located forward of the body. Includes single 38" wide compartment opening per side (with a shallow lower area and a transverse upper area with smooth plate flooring). Rearward transverse compartment area to have triple preconnects with removable trays (side by side). Upper area of transverse module to have diamond plate dunnage pan.
Backboard storage sleeve with retaining strap. Located in LT/RT compartment forward of the speedlays to be 5" high x 20" wide.
Preconnect module (stacked) for use with aluminum speedlay trays. Includes area for (2) stacked preconnect, lower and upper storage compartments with push button latches, running boards.
Center Slam Strip Rear End with (3) compartments‐ (2) lower and (1) upper and a diamond plate center strip for a Jet or Newton Dump application. Includes diamond plate panels.
Center Slam Strip Rear End with (3) compartments‐ (2) lower and (1) upper and a smooth plate center strip for a Jet or Newton Dump application. Includes smooth plate panels.
Upper and Lower Rear Compartment. Includes diamond plate panels.
Upper and Lower Rear Compartment. Includes smooth plate panels.
Full Height Rear Compartment. Includes diamond plate panels.
Full Height Rear Compartment. Includes smooth plate panels.
Full Height Rear Compartment with Upper Ladder Storage Compartment. Includes smooth plate panels. Includes area for storage of (1) 24', (1) 14', (1) 10' Attic, (2) pike poles and a drop down storage access door with push button latches (wire to door ajar).
PRICE
$38,584.00
$10,957.00
$982.00
$10,957.00
$10,957.00
$11,918.00
$2,110.00
$10,290.00
$982.00
$11,565.00
$2,391.00
$2,391.00
$1,843.00
$1,843.00
$1,295.00
$1,295.00
$2,208.00
Option No.
3110‐0007
3110‐0008
3110‐0010
3110‐0011
3110‐0012
3110‐0013
3110‐0014
3110‐0015
3110‐0016
3110‐0017
3110‐0018
3110‐0019
3110‐0020
3110‐0021
3110‐0023
3110‐0024
3110‐0025
3110‐0026
3110‐0027
3110‐0028
3110‐0030
Description
Full Height Rear Compartment. Includes diamond plate panels, 30 degree angle of departure with flip down tailboard and handrails‐ (2) vertically on trailing edge of body and horizontally mounted handrail(s) below hosebed.
Full Height Rear Compartment. Includes smooth plate panels, angled rear body with flip down tailboard and handrails‐ (2) vertical on trailing edge of body and horizontal mounted handrail(s) below hosebed.
Full Height Rear Compartment with Upper Ladder Storage Compartment. Includes area for storage of (1) 24', (1) 14', (1) 10' Attic, (2) pike poles and a drop down storage access door with push button latches (wire to door ajar).
Full Height Rear Compartment with Upper Storage Compartment and Side Storage Tunnel. Includes smooth plate panels and storage access doors with push button latches.
Full Height Rear Compartment with Upper Storage Compartment and Officer Side Ladder Tunnel. Includes diamond plate panels and storage access doors with push button latches.
Full Height Rear Compartment with Officer Side Storage Tunnel. Includes smooth plate panels and storage access door with push button latch.
Full Height Rear Compartment with Officer Side Ladder Tunnel and Recessed Traffic Advisor. Includes smooth plate panels and storage door with push buton latch..
Full Height Rear Compartment with Officer Side Storage Tunnel. Includes diamond plate panels and storage access door with push button latch.
Full Height Rear Compartment with Officer Side Ladder Tunnel and Recessed Traffic Advisor. Includes diamond plate panels and storage door with push button latch.
Full Height Rear Compartment with diamond plate panels.
Full Height Rear Compartment with smooth plate panels.
Full Height Rear Compartment with recessed traffic advisor and smooth plate panels.
Full Height Rear Compartment with recessed traffic advisor and diamond plate panels.
Rear mount rear end with upper storage area and lower pump panel. Includes 12" bolt‐on tailboard, smooth plate panels and upper access area door with push button latches.
Rear mount rear end with upper storage area, lower pump panel area and officer side ladder/equipment tunnel. Includes 12" bolt‐on tailboard, smooth plate panels, upper access area and ladder/equipment storage doors with push button latches.
Stainless Steel rear end with lower center compartment. Includes 12" bolt‐on diamond plate tailboard and handrails‐ (2) vertically on trailing edge of body and horizontally mounted handrail(s) below hosebed.
Stainless steel rear end with lower center compartment.
Rear body panels to be diamond plate.
Rear of body to have un‐painted extrusions with un‐painted smooth plate body panels or just unpainted smooth plate to facilitate rear body striping.
Rear body panels to be painted smooth plate.
(2) bolt‐on compartments. Locate (1) each side of B1. Each compartment includes a hinged diamond plate door (with 4" gap at top for connecting of hose stored in compartment) with D‐Ring latch (wired into door ajar indicator), removable slat flooring and Gator Grip compartment top. Lower hosebed access step (one each side) to be mounted to inboard side of compartment.
PRICE
$2,827.00
$2,827.00
$2,208.00
$2,296.00
$2,296.00
$1,204.00
$1,593.00
$1,167.00
$1,593.00
$1,080.00
$1,080.00
$1,506.00
$1,506.00
$1,790.00
$1,874.00
$2,555.00
$2,732.00
$0.00
$267.00
$936.00
$1,850.00
3110‐0045
Description
Full Height Rear Compartment. Includes diamond plate panels. Opening offset to officer side for special rear compartments. Width to be 31" wide.
Single low rear compartment. For use with low hosebed. Includes diamond plate panels.
Upper rear compartment depth to be shallow.
Upper rear compartment depth to be approximately 25" deep.
Upper and Lower Rear Compartment with Officer Side Ladder Tunnel. Includes diamond plate panels and storage access door with push button latches.
Full Height Rear Compartment. Includes diamond plate panels, recessed traffic advisor and full width rear intermediate step located below the recessed advisor. B1 compartment to have no louvers. Includes access panel on bottom of compartment break to be 7" wide x 32" long. Panel to be centered front to back and side to side.
Bolt‐on diamond plate tailboard (full width of rear compartment). Includes the enhanced extended side compartment frame work with diamond plate compartment tops, (3) folding steps‐ (2) low and (1) high officer side with a 12" handrail (as applicable) and handrails‐ (2) vertically on trailing edge of body and horizontally mounted handrail(s) below hosebed.
Bolt‐on diamond plate tailboard (full width of body). Includes (2) handrails‐ (1) vertical on officer body and (1) horz below hosebed, aluminum ladder (angled) on offier side from tailboard to top edge of body and (3) Cast Products steps (staggered) on driver side.
Compartment B1 to be 30" deep IPOS 26" deep.
Stainless steel rear end assembly. Includes lower rear compartment, tailboard with slanted beavertails and bolt‐on outboard compartments, (4) Cast Products steps‐ (2) each side, (1) intermediate step above B1 and handrails‐ (2) vertically on trailing edge of body and horizontally mounted handrail(s) below hosebed.
Single low rear compartment. For use with low hosebed. Includes smooth plate panels.
Full Height Rear Compartment with Full Width Upper Storage Compartment. Includes officer side area for storage of (1) 10' Attic, (7) pike poles and a drop down storage access door with push buton latches (wire to door ajar). Includes driver side area for storage of backboards and a drop down storage access door with push buton latches (wire to door ajar). Includes (1) divider located 25" off officer's side wall. Includes diamond plate panels.
Bolt‐on diamond plate 10" tailboard (full width of body). Includes handrails‐ (2) mounted vertical on trailing edge of body and horizontal mounted handrail(s) below hosebed.
Upper and Lower Rear Compartment with Officer Side Ladder Tunnel. Includes smooth plate panels and storage access door with push button latches.
3110‐0046
Enhanced extended rear compartmentation for Rescue Pumper. Includes 14" of additional interior width to the rear side compartments and 25" of additional depth in the rearward 14" wide section. Overall interior height will vary depending on additional option selections.
$2,020.00
3110‐0047
Full Height Rear Compartment with Full Width Upper Ladder Storage Compartment with smooth plate panels. Includes area for storage of (1) 24', (1) 14', (1) 10' Attic, (2) pike poles, (1) stokes basket, drop down storage access door with push button latches (wire to door ajar) and retaining straps for tunnel contents. Includes channels each side of ladder tunnel for discharges to terminate.
$3,310.00
Option No.
3110‐0031
3110‐0033
3110‐0034
3110‐0035
3110‐0036
3110‐0037
3110‐0038
3110‐0039
3110‐0040
3110‐0041
3110‐0042
3110‐0043
3110‐0044
PRICE
$1,941.00
$972.00
$0.00
$291.00
$2,870.00
$2,365.00
$903.00
$3,144.00
$915.00
$7,391.00
$1,032.00
$2,625.00
$1,087.00
$2,870.00
Option No.
3110‐0048
3110‐0049
3110‐0050
3110‐0051
3110‐0052
3110‐0053
3110‐0054
3110‐0055
3110‐0056
3110‐0057
3110‐0058
3110‐0060
3110‐0061
3110‐0062
3110‐0063
Description
Enhanced extended rear compartmentation for Rescue Pumper. Includes 14" of additional interior width to the rear side compartments and 25" of additional depth in the rearward 14" wide section. Overall interior height will vary depending on additional option selections. Includes bolt‐on diamond plate tailboard (full width of rear compartment) and handrails‐ (2) vertically on trailing edge of body and horizontally mounted handrail(s) below hosebed.
Bolt‐on diamond plate tailboard (full width of rear compartment). Additional 10" of tailboard to run full width of body ("T" shaped tailboard). Includes the enhanced extended side compartment frame work with diamond plate compartment tops, (1) officer side lower area folding step. Driver side includes (1) upper hosebed mounted handrail (as applicable) and handrails‐ (2) vertical on trailing edge of body and horizontal mounted handrail(s) below hosebed.
Upper Storage Compartment to hold (1) stokes basket in place of standard ladder components. Stokes basket to be located on officer side of storage tunnel. Stop bracket included.
B1 compartment to have no door. Includes removal of compartment lights and door ajar.
Bolt‐on diamond plate tailboard (full width of rear compartment). Includes the enhanced extended side compartment frame work and handrails‐ (2) vertical on trailing edge of body and horizontal mounted handrail(s) below hosebed.
Bolt‐on diamond plate tailboard (full width of rear compartment). Additional 10" of tailboard to run full width of body ("T" shaped tailboard). Includes the enhanced extended side compartment frame work and handrails‐ (2) vertical on trailing edge of body and horizontal mounted handrail(s) below hosebed.
Rear Mount Rear Body. Includes rear body side structures with compartment L3/R3, interior compartment offset for pump panel location and mounting, rear body structure for rear mounted pump application (includes painted job color smooth plate panels outboard of pump access/panel(s) and rear body hosebed.
Rear Mount rearward body compartments (with officer side pump panel). Includes L3‐ 54.5" wide x 24" deep (as applicable) in the 56" lower area and 12" deep in the 12" upper area and R3 (pump panel location)‐ 54.5" wide x 24" deep (as applicable) in the 24" lower area and 12" deep in the 44" upper area.
Compartment preconnect hose feed thru. Includes smooth plate doors with push button latches. Locate to [#LOC] just outboard of the rear pump panel.
Lower Rear Compartment only. Upper section to be diamond plate panel. Includes diamond plate panels.
Rear of body to have flush un‐painted smooth plate body panels to facilitate rear body striping.
Full Height Rear Compartment with Upper Ladder Storage Compartment. Includes diamond plate panels. Includes area for misc. storage and a drop down storage access door with push button latches (wire to door ajar).
Bolt‐on diamond plate tailboard (full width of rear compartment). Includes the enhanced extended side compartment frame work with diamond plate compartment tops, (1) officer side lower area folding step with integral lights. Driver side includes (1) upper hosebed mounted handrail (as applicable) and handrails‐ (2) vertical on trailing edge of body and horizontal mounted handrail(s) below hosebed.
Upper Storage Compartment to hold (1) backboard in place of standard ladder components. Backboard to be located on officer side of storage tunnel. Includes stop bracket located at apporximately 80".
Full Height Rear Compartment with Upper Storage Compartment. Includes smooth plate panels. Includes area for misc. storage and a drop down storage access door with push button latches (wire to door ajar).
PRICE
$2,792.00
$2,432.00
$177.00
$390.00
$1,158.00
$2,432.00
$14,508.00
$0.00
$2,170.00
$1,120.00
$1,379.00
$2,208.00
$903.00
$314.00
$2,208.00
3110‐0071
3110‐0072
3110‐0073
Description
Upper Storage Compartment to have (1) bolt‐in compartment 24" deep. Compartment for storage of misc. items. Includes holding center divider for lower hosebed short to allow room for compartment.
Full Height Rear Compartment with Officer Side Ladder Tunnel. Includes officer side rear tunnel access door with latch (material to match rearend platework).
Full Height Rear Compartment.
Lower Rear Compartment only. Upper section to be diamond plate panel. Includes diamond plate panels. Additional diamond plate area just above compartment for mounting of recessed directional lightbar.
Center Slam Strip Rear End with (3) compartments ‐ (2) lower and (1) upper and a smooth plate center strip for a Jet or Newton Dump application. Includes smooth plate panels. Includes area above upper compartment for directional lightbar.
Full Height Rear Compartment with Upper Storage Compartment and Officer Side Ladder Tunnel. Includes diamond plate panels and storage access doors with Tri‐Mark model 030‐1300 door latches. The upper tunnel to have on the officer side a stop at 128" and on the driver side a stop at 72" from rear of truck.
Upper and Lower Rear Compartment. Includes smooth plate panels. B1 to be 36" wide due to enhanced extended feature and vertically hinged door(s).
Spacer panel(s) for recess/warning lighting. Located:[#LOC]. Panel(s) tol be painted job color and to iinclude mounting area for any and all lighting mounted in area.
Rear of body to have flush painted smooth plate body panels.
Upper rear compartment depth to be approximately 29" deep.
3110‐0074
Full Height Rear Compartment with Officer Side Ladder Tunnel. Includes smooth plate panels and storage access door with push button latch. Includes a 18" channel for (2) tank inlets and (1) 5" jet dump located 16" up from bottom of compartment opening. Includes area above the channel for mounting of a booster reel. The lower opening to have double door and the upper opening to have a dutch door.
$4,914.00
3110‐0075
Full Height Rear Compartment with Officer Side Ladder Tunnel. Includes diamond plate panels and storage access door with push button latch(es). Includes stepped upper horizontal tube to reduce hosebed height from ground over tank and driver side hosebed area.
$3,021.00
Option No.
3110‐0064
3110‐0065
3110‐0066
3110‐0067
3110‐0068
3110‐0069
3110‐0070
PRICE
$623.00
$1,204.00
$1,080.00
$6,217.00
$4,938.00
$2,794.00
$2,586.00
$303.00
$1,686.00
$539.00
$1,354.00
$1,120.00
$267.00
3110‐0080
Full Height Rear Compartment with Officer Side Ladder Tunnel. Includes diamond plate panels and storage access door with D‐ring latch.
Provide modification to B1 officer side compartment opening. To include vertical extrusion and smooth plate panel with lower access door with push button latches for access to tow eye in compartment. Interior width of B1 to remain standard.
Lower Rear Compartment only. Upper section to be smooth plate panel. Includes smooth plate panels.
Rear of body to have painted extrusions with un‐painted smooth plate body panels to facilitate rear body panel striping.
Center Slam Strip Rear End with smooth plate center strip for a Jet or Newton Dump application. Includes smooth plate low side panels and diamond plate upper panel.
3110‐0081
Full Height Rear Compartment with Officer Side Ladder Tunnel. Includes smooth plate panels and storage access door with D‐ring latch.
$1,204.00
3110‐0076
3110‐0077
3110‐0078
3110‐0079
$1,167.00
$2,104.00
Option No.
3110‐0082
3110‐0083
3110‐0085
3110‐0086
3110‐0087
3110‐0088
3110‐0090
3110‐0091
3110‐0092
3110‐0093
3110‐0094
3110‐0095
3110‐0096
3110‐0097
3110‐0098
3110‐0099
3110‐0100
Description
Rear Mount rearward body compartments (with driver side pump panel). Includes R3‐ 60" wide x 24" deep (as applicable) in the 56" lower area and 12" deep in the 12" upper area and L3 (pump panel location)‐ 60" wide x 24" deep (as applicable) in the 24" lower area and 12" deep in the 44" upper area.
Half length offcir side tunnel. Reduces officer side upper compartment depths of R2 and R3 to 12" deep IPO 26".
Upper and Lower Rear Compartment. Includes upper and lower sanded smooth plate panels. Upper rear compartment door to be offset to driver side constructed of smooth plate. Upper rear compartment to be 56" wide for little giant ladder storage. (2) 1.5" x 4" extrusions to be stacked between upper and lower compartments for directional light mounted under intermediate rear step.
Bolt‐on diamond plate 24" tailboard (full width of hosebed). Includes handrails‐ (2) vertical mounted on trailing edge of body and (1) horizontal mounted handrail(s) below hosebed.
Full Height Rear Compartment with Upper Storage Compartment and Officer Side Ladder Tunnel. Includes smooth plate panels and storage access doors with Tri‐Mark door latches.
Full Height Rear Compartment with Officer Side Ladder Tunnel. Includes diamond plate panels and storage access door with push button latch. Officer side to have Rescue Pumper and Driver to have Pumper style enhanced extended.
Handrail above B1 and below the hosebed will be "split". Each handrail to be approximately 18" and installed approximately 6" offset of centerline of B1 to allow for a 12" gap at center.
Rear Mount rearward body compartments (with officer side pump panel). Includes L3‐ 60" wide x 24" deep (as applicable) in the 56" lower area and 12" deep in the 12" upper area and R3 (pump panel location)‐ 60" wide x 24" deep (as applicable) in the 24" lower area and 12" deep in the 44" upper area.
Enhanced Extended Compartmentation stepped down below hosebed level. Includes embossed diamond plate compartment tops.
Full Height Rear Compartment with Driver Side Storage Tunnel. Includes smooth plate panels and storage access door with push button latch.
Full Height Rear Compartment with Upper Storage Compartment and Driver Side Storage Tunnel. Includes smooth plate panels and storage access doors with push button latches.
Full Height Rear Compartment with Driver and Officer Side Storage Tunnels. Includes smooth plate panels and storage access doors with push button latches.
Full Height Rear Compartment with Upper Storage Compartment, Driver and Officer Side Storage Tunnels. Includes smooth plate panels and storage access doors with push button latches.
Bolt‐on smooth plate tailboard (full width of rear compartment). Tailboard to include gator grip and be black duraback painted. Includes the enhanced extended side compartment frame work (2008 design) and handrails‐ (2) vertically on trailing edge of body and horizontally mounted handrail(s) below hosebed. Handrails to include center stanchion.
Rear Mount rearward body compartments (with officer side pump panel). Includes L3‐ 60" wide x 24" deep (as applicable) in the 30" lower area and 12" deep in the 34" upper area and R3 (pump panel location)‐ 60" wide x 24" deep (as applicable) in the 24" lower area and 12" deep in the 44" upper area.
NFPA hose bed access ladder. Zico model RL12 for increased visibility of rear outboard body mounted DOT/NFPA lighting. Includes required step lights and additional hand rail(s) if applicable. Location: [#LOC].
Backboard stop bracket to be located approximately 76" back in officer side of ladder tunnel.
PRICE
$0.00
$2,193.00
$2,395.00
$1,155.00
$2,871.00
$4,615.00
$544.00
$0.00
$0.00
$1,204.00
$2,296.00
$1,328.00
$2,569.00
$1,753.00
$0.00
$1,816.00
$251.00
Option No.
3110‐0101
3110‐0102
3110‐0103
3110‐0104
3110‐0105
3110‐0106
3110‐0107
3110‐0108
3110‐0109
3110‐0110
3110‐0111
3110‐0112
3110‐0113
Description
Compartment preconnect hose feed thru. Includes smooth plate doors with push button latches. Locate to [#LOC] just outboard of the rear pump panel.
Upper Storage Compartment to hold (2) backboards in place of standard ladder components. Backboard to be located on officer side of storage tunnel. Includes stop bracket located at approximately 74".
Bolt‐on diamond plate tailboard (full width of rear compartment). Includes the enhanced extended side compartment frame work with diamond plate compartment tops (embossied IPO Gator Grip due to department mounting of hose storage connectors in this area) and (1) driver and officer side lower area folding step (NO steps on driver or officer side upper areas). Main hosebed access is to be from the driver side of the pump module access ladder). Includes handrails‐ (2) vertically on trailing edge of body and horizontally mounted handrail(s) below hosebed.
(2) vertically mounted booster reel roller assemblies. Locate (1) each side inboard side of the enhanced extended area (as far outboard as applicable). For use with rear compartment mounted booster reel.
Upper Storage Compartment to hold (1) 17' Little Giant ladder and (1) backboard in place of standard ladder components. Little giant ladder to be located on officer side of storage tunnel stop bracket included approximately 113" back from opening, ladder to be stored in unfolded position. Backboard to be located in aluminum box hanging from upper area of officer side tunnel. Tunnel divider to be held 6" short from opening.
Rear Mount pump/ladder tunnel access door. Includes single center mounted D‐Ring latch and (2) hold open devices. Door to be [#LOC]. Door to open to 90 degrees and includes pull strap for access from ground.
Upper and Lower Rear Compartment. Includes smooth plate panels. Includes a 19" channel for (2) tank inlets and (1) 5" jet dump located between the upper and lower non‐transverse style compartments. The lower compartment height to be 15".
Rear Mount rearward body compartments (with driver side pump panel). Includes R3‐ 60" wide x 24" deep (as applicable) in the 30" lower area and 12" deep in the 34" upper area and L3 (pump panel location)‐ 60" wide x 24" deep (as applicable) in the 24" lower area and 12" deep in the 44" upper area.
Upper and Lower Rear Compartment. Includes smooth plate lower panels outboard of B1 and diamond plate upper panels outboard of B2. The B1 compartment to be 42" wide and B2 compartment to be 38" wide. Includes (2) 1.5" x 4" extrusions to be stacked between upper and lower compartments for directional light mounted under intermediate rear step.
Rear Mount Rear Body. Includes rear body side structures with compartment L3/R3, interior compartment offset for pump panel location and mounting, rear body structure for rear mounted pump application. Includes painted job color smooth plate panels (and storage access door with push button latch, if applicable) outboard of pump access/panel(s) and rear body hosebed.
Upper and Lower Rear Compartment. Includes smooth plate lower panels outboard of B1 and diamond plate upper panels outboard of B2. Includes (2) 1.5" x 4" extrusions to be stacked between upper and lower compartments for directional light mounted under intermediate rear step and back‐up camera to be mounted centered in front of directional lightbar. The upper compartment to be offset to officer side due to rear discharge options.
The rear mounted E‐ONE logo to be the small size and mount to the outboard side on the driver side rear compartment face. No logo or tags are to be installed on the exterior rear pump/ladder access door.
Bolt‐on diamond plate 12" tailboard with Gator Grip (full width of body). Includes hand rails‐ (2) vertical on trailing edge of body and horizontal mounted hand rail(s) below hose bed.
PRICE
$1,316.00
$623.00
$1,017.00
$508.00
$623.00
$513.00
$3,952.00
$0.00
$3,855.00
$10,246.00
$3,855.00
$0.00
$1,087.00
3110‐0129
Description
Bolt‐on diamond plate 12" tailboard full width of body with Bustin Tread. This provides a flat back body design. Includes hand rails, (2) vertically on trailing edge of body and horizontally mounted hand rail below hose bed.
Bolt‐on diamond plate 12" tailboard with Gator Grip (full width of body). Includes (2) squared off beavertails with hand rails‐ (2) vertically on trailing edge of body and horizontally mounted hand rail below hose bed.
Bolt‐on diamond plate 12" tailboard full width of body with Bustin Tread. Includes (2) squared off beavertails with hand rails, (2) vertically on trailing edge of beavertails and horizontally mounted hand rail below hose bed.
Bolt‐on diamond plate 20" tailboard with Gator Grip. Includes hand rails‐ (2) vertically on trailing edge of body and horizontally mounted hand rail(s) below hose bed.
Bolt‐on diamond plate 20" tailboard between rear side compartments with Bustin Tread. Includes hand rails (2) vertically on trailing edge of body and horizontally mounted hand rail below hose bed.
Bolt‐on diamond plate 20" tailboard with Gator Grip (full width of body). Includes (2) squared off beavertails with hand rails‐ (2) vertically on trailing edge of body and horizontally mounted hand rail(s) below hose bed.
Bolt‐on diamond plate 20" tailboard with Bustin Tread (full width of body). Includes (2) squared off beavertails with hand rails, (2) vertically on trailing edge of body and horizontally mounted hand rail below hose bed.
Bolt‐on diamond plate 20" tailboard with Gator Grip (full width of body). Includes (2) slanted beavertails with removable outer panels and hand rails‐ (2) vertically on trailing edge of body and horizontally mounted hand rail(s) below hose bed.
Bolt‐on diamond plate 20" tailboard with Bustin Tread (full width of body). Includes (2) slanted beavertails and hand rails, (2) vertically on trailing edge of body and horizontally mounted hand rail below hose bed.
Lower rear stainless steel short compartment B1, 46" wide x 35" high x 26" deep. Includes bolt‐on intermediate step above. Entire rear panel to be smooth aluminum plate for Chevron graphics.
Lower rear stainless steel tall compartment B1, 46" wide x 45" high x 26" deep. Includes bolt‐on intermediate step above. Entire rear panel to be smooth aluminum plate for Chevron graphics.
Upper Storage Tunnel to have bolt‐in side panels to enclose the sides of the tunnel.
Upper and Lower Rear Compartment with Driver and Officer Side Storage Tunnels. Includes smooth plate panels. Includes a 19" area for (1) tank inlet and (1) 5" jet dump located between the upper and lower compartments. The lower compartment height to be 17". The upper compartment to be full height and depth, includes bolt‐in floor for access to plumbing components. Driver side tunnel opening to be narrowed to allow non‐recessed folding step.
Bolt‐on diamond plate 18" tailboard (full width of body). Includes (2) slanted beavertails (no stanchions) with removable outer panels and handrails‐ (2) vertically on trailing edge of body and horizontally mounted handrail(s) below hosebed. Upper beavertail to be 8.75 due to folding steps.
Full Height Rear Compartment with smooth plate panels. The rear compartment to be 36" due to the enhanced extended compartment and double door options.
Full Height Rear Compartment with Officer Side Storage Tunnel. Includes smooth plate panels and storage access door with push button latch. The rear compartment to be 36" due to the enhanced extended compartment and double door options.
3110‐0130
Rear end tanker. Includes smooth plate upper and lower panels and a smooth plate center strip for a Jet or Newton Dump application.
Option No.
3110‐0114
3110‐0115
3110‐0116
3110‐0117
3110‐0118
3110‐0119
3110‐0120
3110‐0121
3110‐0122
3110‐0123
3110‐0124
3110‐0125
3110‐0126
3110‐0127
3110‐0128
PRICE
$1,087.00
$815.00
$815.00
$1,011.00
$1,011.00
$1,011.00
$1,011.00
$1,011.00
$1,011.00
$1,120.00
$1,295.00
$623.00
$4,239.00
$1,264.00
$1,425.00
$1,549.00
$649.00
Option No.
3110‐0131
3110‐0132
3110‐0133
3110‐0134
3110‐0135
3110‐0136
3110‐0137
3110‐0138
3110‐0139
3110‐0140
3110‐0142
3110‐0143
3110‐0144
3110‐0145
3110‐0146
3110‐0147
Description
Full Height Rear Compartment with Officer Side Storage Tunnel. Includes smooth plate panels and storage access door with push button latch. Includes stepped upper horizontal tube to reduce hosebed height from ground over tank area.
Bolt‐on diamond plate tailboard (full width of rear compartment). Additional 10" of tailboard to run full width of body ("T" shaped tailboard). Includes the enhanced extended side compartment frame work and handrails ‐ (1) vertical on trailing edge of body opposite side of ladder and handrail(s) horizontal below hosebed.
Rear end tanker. Includes smooth plate upper and lower panels, a smooth plate center strip for a Jet or Newton Dump application and upper area access door for thru the tank storage.
Lower rear stainless steel short compartment B1, TBD" wide x TBD" high x TBD" deep. Entire rear panel to be smooth aluminum plate for Chevron graphics.
Lower rear stainless steel tall compartment B1, TBD" wide x TBD" high x TBD" deep. Entire rear panel to be smooth aluminum plate for Chevron graphics.
Full Height Rear Compartment with Upper Ladder Storage Compartment. Includes smooth plate panels. Includes area for storage of (1) 24', (1) 14', (1) 10' Attic, (4) pike poles and a lift‐up storage access door with push buton latches (wire to door ajar). Lift‐up door to use plunger style hold open device. Includes "NO STEP" tags located on outboard ends and positioned to be read from the open position of the door.
Rear body panels to be painted smooth FRP.
Rearend assembly with 3/4 height rear body compartment. Compartment located directly above chassis frame rails and to be non‐
transverse. For use with Industrial products and pumpers with large fuel tanks over 65 gallons. only.
Rearend assembly with no rear compartment. For use with Industrial products only.
Rearend assembly with 3/4 height rear end and dual dry chemical access doors. The upper access areas to either side of the center section to provide access to the dry chemical vessel and the nitorgen bottle(s). For use with Industrial products only.
Upper rear compartment stepped for use newton dump.
(2) bolt‐on compartments. Locate (1) each side of B1. Each compartment includes a hinged smooth plate door with D‐Ring latch (wired into door ajar indicator), removable slat flooring and Gator Grip compartment top. Driver side compartment to be 37" high and officer side compartment to be 31" high. Lower hosebed access step (two driver side and one officer side) to be mounted to inboard side of compartment.
Bolt‐on diamond plate tailboard (full width of rear compartment). Additional 10" of tailboard to run full width of body ("T" shaped tailboard). Includes the enhanced extended side compartment frame work and handrails ‐ (1) vertical on trailing edge of body opposite side of ladder and handrail(s) horizontal below hosebed on trailing edge of the intermediate step.
Full Height Rear Compartment with smooth plate panels.
Rear end with full height compartment. Includes diamond plate panels and double upper extrusions below hosebed area. Interior of compartment to be transverse side to side.
Bolt‐on diamond plate 16" tailboard (full width of body). Includes (2) slanted beavertails with raised stanchions post with E‐ONE logo style mounts and removable outer panels, handrails‐ (2) vertically on trailing edge of body/beavertail and horizontally mounted handrail below hosebed on trailing edge of intermediate step.
PRICE
$2,352.00
$2,432.00
$764.00
$0.00
$0.00
$2,208.00
$289.00
$1,295.00
$649.00
$972.00
$203.00
$2,136.00
$2,432.00
$1,366.00
$1,583.00
$815.00
Option No.
3110‐0148
3110‐0149
3110‐0150
3110‐0151
3110‐0152
3110‐0153
3110‐0154
3110‐0155
3110‐0156
3110‐0157
3110‐0158
3110‐0159
3110‐0160
3110‐0161
3110‐0162
Description
Bolt‐on tailboard compartments located to the driver and officer side of B1. The bolt‐on tailboard compartments to be 64" high with embossed diamond plate compartment tops. The compartments includes hinged smooth plate door with 1/4 turn latch(es). The each compartment to have 4" gap at top of the door. Each door to be wired into door ajar indicator.
Full Height Rear Compartment with Upper Ladder Storage Compartment. Includes smooth plate panels. Includes area for storage of (1) 24', (1) 14', (1) 10' Attic, (2) pike poles and a drop down storage access door with Tri‐Mark latch (wire to door ajar).
Upper Storage Compartment to hold (1) 17' Little Giant ladder. Little giant ladder to be located on driver side of storage tunnel stop bracket included approximately 58" back from opening.
Bolt‐on diamond plate tailboard (full width of rear compartment). Additional 5.5" of tailboard to run full width of body ("T" shaped tailboard). Includes the enhanced extended side compartment frame work with diamond plate compartment tops, (1) officer side lower area folding step. Driver side includes (1) upper hosebed mounted handrail (as applicable) and handrails‐ (2) vertically on trailing edge of body and horizontally mounted handrail(s) below hosebed.
Upper Storage Compartment divider to be located offset 26" from officer side. Officer side of divider to be enclosed to 86" deep and driver side of divider to be enclosed to 72" deep.
Rear access into the enhanced extended portion of the L2 and R2 compartments. Includes smooth plate access doors with (2) push button latches each (wired to door ajar).
Bolt‐on diamond plate 6" tailboard (full width of body). Includes handrails‐ (2) vertically on trailing edge of body and horizontally mounted handrail(s) below hosebed.
Extruded lower rearend for use with Wetside tank. Includes smooth plate panels and area for Newton dump application.
Upper Storage Compartment to hold (1) 17' Little Giant ladder, (1) 24' 2‐section ladder, (1) 14' roof ladder, (1) 10' attic ladder and (2) pike poles.
Rear end with Upper Storage Compartment. Includes smooth plate panels. Includes area for misc. storage and vertical hinged double doors with D‐ring latch (wire to door ajar).
Bolt‐on diamond plate 16" tailboard (full width of body). Includes handrails‐ (2) vertical on trailing edge of body and horizontal mounted handrail(s) below hosebed.
Full Height Rear Compartment with smooth plate panels for mini pumper. Compartment width will be 44" wide.
(2) bolt‐on compartments. Locate (1) each side of B1 ‐ driver side to have 11.5" wide x 46" high opening and officer side to have 14.5" wide x 29" high opening. Each compartment to be 21" deep. Each compartment includes a hinged smooth plate door (with 4" gap at top for connecting of hose stored in compartment) with D‐Ring latch (wired into door ajar indicator), removable slat flooring and Gator Grip compartment top. Lower hosebed access step (two on the driver side and one on the officer side) to be mounted to inboard side of compartment.
Bolt‐on diamond plate 25" tailboard (full width of body). Includes (2) squared off beavertails (no stanchions) with removable outer panels and (2) 48" handrails vertical on beavertails and (1) 36" horizontal below hosebed.
Full Height Rear Compartment with Officer Side Storage Tunnel. Includes smooth plate panels and storage access door with push button latch. B1 compartment opening to be 35" wide due to officer side tailboard compartment.
PRICE
$3,119.00
$2,290.00
$623.00
$2,432.00
$623.00
$797.00
$1,125.00
$1,048.00
$623.00
$2,208.00
$1,257.00
$1,080.00
$1,993.00
$1,246.00
$1,377.00
Option No.
3110‐0163
3110‐0164
3110‐0165
3110‐0166
3110‐0167
3110‐0168
3110‐0169
3110‐0170
3110‐0171
3110‐0172
3110‐0173
3110‐0174
3110‐0175
3110‐0176
3110‐0177
3110‐0178
Description
Enhanced extended rear end with tall rear compartment and with officer side storage tunnel. Driver side enhanced extended to be be Pumper style and officer to be Recue Pumper style.Officer side hosebed extrusion to be stepped for storage tunnel. Included are diamond plate tailboard full width of the rear compartment, smooth plate panels and storage access door (wired to door ajar) with push button latch.
Bolt‐on diamond plate 24" tailboard (full width of body). Includes (2) squared off 12" deep beavertails (no stanchions) with removable outer panels and handrails‐ (2) vertical on trailing edge of body and horizontal mounted handrail(s) below hosebed. The outer beavertail panels to be aluminum smooth plate to allow for chevron striping. For use with swivel style rear tank dump only.
Full Height Rear Compartment with Driver Side Storage Tunnel. Includes smooth plate panels and storage access door with push button latch. The rear compartment to be 36" due to the enhanced extended compartment and double door options.
Full height rear compartment with officer side storage tunnel. Includes bolt‐on intermediate step above. SS eMAX only.
Full Height Rear Compartment with Upper Storage Compartment and Officer Side Ladder Tunnel. Includes smooth plate panels and storage access doors with Tri‐Mark model 030‐1300 door latches. The upper tunnel access door to be horizontally hinged lift‐up with gas shock. The upper tunnel to have on the officer side a stop at 128" and on the driver side a stop at 72" from rear of truck.
Bolt‐on diamond plate tailboard (full width of rear compartment). Additional 5" of tailboard to run full width of body ("T" shaped tailboard). Includes the enhanced extended side compartment frame work, (1) officer side lower area folding step and handrails‐ (2) vertically on trailing edge of body and horizontally mounted handrail(s) below hosebed.
Right Rear Panel Compartment at the rear face of the body on the right side. The compartment shall be 58" high x 27" wide x 10" deep equipped with a single stainless steel lap style door with D‐ring locking latch. The floor will be lined with 1/2" U.H.M.W plastic.
Lower Rear Compartment with Officer Side Storage Tunnel. Includes smooth plate panels and storage access door with push button latch.
Rear of stainless steel aerial body to have un‐painted smooth plate panels to facilitate rear body striping.
Bolt‐on diamond plate 14" tailboard full width of body with Bustin Tread, provides flat back body design. Includes rear of body hand rails.
Rear body smooth ladder door be painted job color finish to match body color.
Traffic advisor platework to be removed to allow for taller compartment opening.
Lower Rear Compartment only. Upper section to be smooth plate panel. Includes smooth plate panels. Upper section to be set back 8" with diamond plate step with gator grip.
Full Height Rear Compartment. Includes smooth plate panels. B1 to be as tall as possible (remove traffic advisor platework).
Bolt‐on diamond plate 12" tailboard (full width of body). Includes (2) squared off beavertails (no stanchions) with removable outer panels and (2) vertical mounted handrails on trailing edge of body.
Full height rear compartment. Includes smooth plate panels. Bolt‐on diamond plate tailboard (full width of rear compartment). Includes the driver side rescue style enhanced extended side compartment frame work with diamond plate compartment tops, officer side pumper style enhanced extended side compartment frame work with diamond plate compartment top. Officer side lower rear compartment will be transverse with B1. Handrail included and located: (1) driver upper hosebed mounted handrail (as applicable) and handrails‐ (2) vertically on trailing edge of body and horizontally mounted handrail(s) below hosebed.
PRICE
$2,596.00
$1,388.00
$1,549.00
$1,436.00
$2,794.00
$1,776.00
$2,822.00
$1,328.00
$309.00
$1,151.00
$414.00
$0.00
$2,615.00
$1,268.00
$815.00
$2,996.00
Option No.
3110‐0179
3110‐0180
3110‐0181
3110‐0182
3110‐0183
3110‐0184
3110‐0185
3110‐0186
3110‐0187
3110‐0188
3110‐0189
3110‐0190
3110‐0191
3110‐0193
3110‐0194
3110‐0195
Description
Upper Storage Compartment to hold (1) 24' 2‐section ladder, (1) 14' roof ladder, (1) 12' pike pole, (1) 8' pike pole, (2) 6' pike poles and (2) 6' D‐handle trash hooks. Area rearward of pike poles to be closed off just before fill towers.
Bolt‐on diamond plate 14" tailboard (full width of body). For use with rear ladder/flat back style application. Includes handrails‐ (1) mounted vertical on trailing edge of body opposite side of ladder and handrail(s) horizontal below hosebed.
Rear flip down tailboard. Includes indicator in cab when the tailboard is in the down position. Includes handrails‐ (2) vertically on trailing edge of body and horizontally mounted handrail(s) below hosebed.
Full Height Rear Compartment with Upper Storage Compartment. Includes diamond plate panels. Includes area for misc. storage and a drop down storage access door with a D‐ring latch (wire to door ajar).
Full height rear compartment with upper ladder storage compartment. Includes smooth plate panels. Includes area for storage of (1) 24',(1)14',(1)10' attic, (2) pike poles and a drop down storage access door with push button latches (wire to door ajar).note door to open up past 90 degrees.
(2) bolt‐on compartments. Locate (1) each side of B1 ‐ driver side to have 13" wide opening and officer side to have 16" wide opening. Each compartment includes a hinged smooth plate door (with 4" gap at top for connecting of hose stored in compartment) with D‐Ring latch (wired into door ajar indicator), removable slat flooring and Gator Grip compartment top. Lower hosebed access step (one each side) to be mounted to inboard side of compartment.
Upper and Lower Rear Compartment. Includes smooth plate panels. Upper compartment to be as tall as possible (remove traffic advisor platework).
Full Height Rear Compartment with Officer Side Storage Tunnel. Includes smooth plate panels and storage access door with push button latch. Area just below hosebed for discharge pipe routing above the rear compartment. Includes stepped upper horizontal tube to reduce hosebed height from ground over tank area.
Rearend assembly with 3/4 height rear body for dry chemical access. Includes smooth plate panels. Compartment opening located directly above chassis frame rails and vertically hinged access door with D‐ring latches. For use with Industrial products only.
Bolt‐on diamond plate 10" tailboard (full width of body). For use with rear ladder application. Includes a handrail vertically mounted on trailing edge of body opposite side of ladder.
Full Height Rear Compartment with Officer Side Storage Tunnel. Includes smooth plate panels and storage access door with push button latch (remove traffic advisor platework).
Lower rear stainless steel short compartment B1, 46" x 35" high x 26" deep. Includes intermediate step above. Side walls removed to allow a Little Giant ladder to be slid in from compartment R3. Provide a stainless steel bolt‐on panel to conceal and protect ladder when stored.
Bolt‐on diamond plate 14" tailboard between rear side compartments with Bustin Tread. Includes hand rails (2) vertically on trailing edge of body and horizontally mounted hand rail below hose bed.
Full Height Rear Compartment with Driver Side Storage Tunnel. Includes smooth plate panels and storage access door with push button latch.
Full Height Rear Compartment with smooth plate panels. The B1 compartment to be 40" wide, full depth (no compartment break) and as tall as possible (remove traffic advisor platework).
Full Height Rear Compartment. Includes smooth plate panels. The rear compartment to be 36" due to the enhanced extended compartment and double door options.
PRICE
$797.00
$1,120.00
$3,926.00
$2,208.00
$2,208.00
$1,993.00
$1,961.00
$2,611.00
$1,295.00
$974.00
$1,204.00
$1,385.00
$1,151.00
$1,659.00
$1,659.00
$1,196.00
Option No.
3110‐0196
3110‐0197
3110‐0198
3110‐0199
3110‐0200
3110‐0201
3110‐0202
3110‐0203
3110‐0204
3110‐0205
3110‐0206
3110‐0207
3110‐0208
3110‐0209
3110‐0210
3110‐0211
Description
Rear end assembly with dual dry chemical access doors. The upper access areas to either side of the center section to provide access to the dry chemical vessel and the nitrogen bottle(s) to include (2) dividers.
The rear mounted E‐ONE logo to be centered on the rear Stokes storage door.
B1 floor to be recessed as applicable to allow for booster reel and/or dealer installed equipment to be located below newton dump/applicable dump without interference.
Compartment B1, 24" wide x 10" high x 26" deep, located between full length chassis frame rails. The compartment shall include a bottom hinged drop‐down access door using a D‐ring latch (wire to door ajar).
Full Height Rear Compartment with Driver and Officer Side Storage Tunnels. Includes smooth plate panels and storage access doors with d‐ring latches.
Bolt‐on diamond plate tailboard (full width of rear compartment). Additional 10" of tailboard to run full width of body ("T" shaped tailboard). Includes the enhanced extended side compartment frame work and (1) handrail vertical on trailing edge of driver's side of body and horizontal mounted handrail (driver's side) below hosebed.
Upper and Lower Rear Compartment. Includes upper and lower sanded smooth plate panels. Upper rear compartment door to be offset to driver side constructed of smooth plate. Upper rear compartment to be 56" wide for little giant ladder storage. (2) 1.5" x 4" extrusions to be stacked between upper and lower compartments for directional light mounted under intermediate rear step.
Bolt‐on diamond plate tailboard (full width of rear compartment). Includes the enhanced extended side compartment frame work with diamond plate compartment tops raised 12" to cover rear piping, (1) officer side lower area folding step. Driver side includes (1) upper hosebed mounted handrail (as applicable) and handrails‐ (2) vertically on trailing edge of body and horizontally mounted handrail(s) below hosebed.
Lower rear stainless steel tall compartment B1, 46" wide x 50" high x 26" deep. Includes bolt‐on intermediate step above. Entire rear panel to be smooth aluminum plate for Chevron graphics.
Full Height Rear Compartment with smooth plate panels for mini pumper. Compartment opening dimensions will be approximately 44" wide x 38" wide. Extra compartment height will reduce the hosbed by approximately 11".
Full Height Rear (no compartment). Includes opening for access to rear mount pump panel and smooth plate panels. Includes openings for preconncts to driver's side of rear pump panel
Lower rear stainless steel short compartment B1, 46" wide x 35" high x 26" deep, without an intermediate rear step. Entire rear panel to be smooth aluminum plate for Chevron graphics.
Bolt‐on diamond plate 10" tailboard (full width of body). For use with a folding step application. Includes handrails‐ (2) vertical on trailing edge of body and handrail(s) horizontal below hosebed.
Upper and Lower Rear Compartment. Includes smooth plate panels. B1 to be 36" wide due to enhanced extended feature and hinged door(s) as required.
Bolt‐on diamond plate 10" tailboard (full width of body). For use with folding step application. Includes handrails‐ (1) vertical on trailing edge each side of body and handrail(s) horizontal below hose bed.
Bolt‐on diamond plate tailboard (full width of rear compartment). Includes the enhanced extended side compartment frame work with diamond plate compartment tops, (2) recessed folding steps in lower area (1) officer side, (1) driver side. Driver side includes (1) upper hosebed mounted handrail (as applicable) and handrails‐ (2) vertically on trailing edge of body and horizontally mounted handrail(s) below hosebed.
PRICE
$2,012.00
$0.00
$528.00
$1,014.00
$1,357.00
$2,432.00
$2,395.00
$1,246.00
$1,380.00
$1,080.00
$1,537.00
$895.00
$748.00
$2,586.00
$974.00
$1,167.00
Option No.
3110‐0212
3110‐0213
3110‐0215
3110‐0216
3110‐0217
3110‐0218
3110‐0220
3110‐0221
3110‐0222
3110‐0223
3110‐0224
3110‐0225
3110‐0226
3110‐0227
Description
Bolt‐on diamond plate tailboard (full width of hosebed). Additional 10" of tailboard to run full width of body ("T" shaped tailboard). Includes the extended side compartment frame work and handrails‐ (2) vertical mounted on trailing edge of body and horizontal mounted handrail(s) below hosebed.
Bolt‐on diamond plate 20" tailboard with Bustin Tread (full width of body). Includes (2) slanted beavertails and hand rails, (2) vertically on trailing edge of body and horizontally mounted hand rail below hose bed. Lower rear stainless steel short compartment B1, 46" wide x 35" high x 26" deep, without an intermediate rear step. Entire rear panel to be smooth stainless steel for Chevron graphics.
Upper Storage Compartment to hold (1) 10' attic ladder, (4) pike poles, and (2) 6" x 10' hard suction hoses. Includes stop bracket included approximately 130" back from opening. An enclosed frontal area shall be included as part of the tunnel design.
Bolt‐on diamond plate 12" tailboard (full width of body). Includes (2) squared off beavertails with stanchions and removable outer panels and handrails‐ (2) vertical on trailing edge of body and horizontal mounted handrail(s) below hosebed.
(1) Officer side rear pump module roof top compartment. Includes hinged raised aluminum smooth plate with black Scorpion coating (IPOS diamond plate) compartment lid with turn latches and grab handle(s). Compartment to have (1) bracket mounted LED light and wired to door ajar indicator in cab. Outboard side of body to run full width and wrap around the rear and meet with the end of the hosebed end.
(1) Driver side rear pump module roof top compartment. Includes hinged raised smooth plate with black Scorpion coating (IPOS diamond plate) compartment lid with turn latches and grab handle(s). Compartment to have (1) bracket mounted LED light and wired to door ajar indicator in cab. Outboard side of body to run full width and wrap around the rear and meet with the end of the hosebed end.
Bolt‐on 10" tailboard (full width of body) aluminum smooth plate with black Scorpion coating (IPOS diamond plate). For use with rear ladder application. Includes handrails‐ (1) vertically on trailing edge of body opposite side of ladder and handrail(s) horizontally below hosebed.
Full height rear compartment with upper storage compartment. Includes smooth plate panels. Includes area for misc. storage and a lift up storage access door with push button latches (wire to door ajar).
Bolt‐on 10" diamond plate tailboard (full width of rear compartment). Includes the enhanced extended side compartment frame work. For use with rear ladder application. Includes handrails (1) vertical mounted on trailing edge of body opposite side of ladder and (1) horizontal mounted handrail(s) below hosebed.
Full Height Rear Compartment with Officer Side Storage Tunnel. Includes smooth plate panels and storage access door with d‐ring latch.
Rear body panels to be upgraded from smooth aluminum plate to un‐painted smooth FRP.
Full Height Rear Compartment with Upper Ladder Storage Compartment. Includes smooth plate panels. Includes area for storage of (1) 24', (1) 14', (1) 10' Attic, (2) pike poles and a lift up storage access door with push button latches (wire to door ajar). The door shall be held in place with a plunger style hold open device.
Bolt‐on diamond plate 22" tailboard between rear side compartments with Bustin Tread. Includes hand rails (2) vertically on trailing edge of body and horizontally mounted hand rail below hose bed.
Upper and lower rear compartment. Includes smooth plate panels. For use with raised lower rear body (B1 is 25" high).
PRICE
$2,432.00
$2,222.00
$623.00
$815.00
$1,719.00
$1,719.00
$1,278.00
$2,377.00
$2,130.00
$1,204.00
$289.00
$2,208.00
$1,151.00
$1,843.00
Option No.
3110‐0228
3110‐0229
3110‐0230
3110‐0231
3110‐0232
3110‐0233
3110‐0234
3110‐0235
3110‐0236
3110‐0237
3110‐0238
3110‐0239
3110‐0240
3110‐0241
3110‐0242
Description
Bolt‐on diamond plate 12" tailboard (full width of body). Includes (2) squared off beavertails (no stanchions) with removable outer panels and handrails‐ (2) vertical trailing edge of body and horizontal mounted handrail(s) below hosebed. Beavertails and outer panels to be smooth plate painted job color. Tailboard to diamond plate painted black durabak.
Lower rear stainless steel tall compartment B1, 46" wide x approx. 64" high x 26" deep, but door opening remains in the normal 45" high position. Includes bolt‐on intermediate step above the door opening. Entire rear panel to be smooth plate for Chevron graphics.
Bolt‐on 10" tailboard (full width of body) aluminum smooth plate with black Scorpion coating (rough finish) IPOS diamond plate. For use with rear ladder application. Includes handrails‐ (1) vertically on trailing edge of body opposite side of ladder and handrail(s) horizontally below hosebed.
(1) bolt‐on compartment. Locate on the officer side of rear step and to have 16" wide opening. The compartment includes a vertically hinged smooth plate door (with 4" gap at top for connecting of hose stored in compartment) with D‐ring latch (wired into door ajar indicator), removable Duradek flooring and embossed non‐skid treadplate compartment top. Lower hose bed access step to be mounted to inboard side of compartment.
Bolt‐on diamond plate 22 inch tailboard tailboard (full width of body). Includes (2) squared off beavertails (no stanchions) with removable outer panels and handrails‐ (2) vertical on trailing edge of body and horizontal mounted handrail(s) below hosebed.
Bolt‐on tailboard compartments located to the driver and officer side of B‐1. The bolt‐on tailboard compartments to be full height just below hosebed. Doors to be (1) Piece full height as applicable and hinged to the outside with push‐button latches. Install shelf tracking in each compartment full height
Upper Storage Compartment to hold (1) stokes basket in place of standard ladder components. Stokes basket to be located on officer side of storage tunnel. Stop bracket full width across tunnel shall be included.
Step full width rear intermediate. Intermediate rear step to be located just below the upper ladder storage compartment.
Step full width rear intermediate. Intermediate rear step to be located just above the upper ladder storage compartment.
Full height rear compartment with upper storage compartment. Includes smooth plate panels. Includes an area for misc. storage and a lift up storage access door with a D‐ring latch (wire to door ajar) and a plunger style hold open device. To include a storage sleeve for (2) backboards (72"X16"X2" each) offset to the officer side with a stop at 80".
Bolt‐on diamond plate 18" tailboard (full width of body). Includes handrails‐ (2) vertically on trailing edge of body and handrail(s) horizontally below hosebed.
Bolt‐on diamond plate 10" tailboard (full width of body). Includes handrail ‐ (1) vertically on officer side trailing edge of body and horizontally mounted handrail(s) below hosebed.
Lower Rear Compartment with access door above to the ladders storage thru tank. Includes smooth plate panels and storage access door with push button latches.
(1) bolt‐on compartment 17" W x 40" H x 11" D. Locate on the officer side of rear step and to have 15" wide opening. The compartment includes a vertically hinged smooth plate door (with 4" gap at top for connecting of hose stored in compartment) with D‐ring latch (wired into door ajar indicator), removable Duradek flooring and embossed non‐skid treadplate compartment top. Lower hose bed access steps to be mounted to inboard side of compartment.
Bolt‐on diamond plate 25" tailboard between rear side compartments with Bustin Tread. Includes hand rails (2) vertically on trailing edge of body and horizontally mounted hand rail below hose bed.
PRICE
$2,011.00
$1,433.00
$1,278.00
$998.00
$1,275.00
$3,692.00
$177.00
$843.00
$843.00
$2,542.00
$1,856.00
$1,087.00
$1,798.00
$1,056.00
$1,151.00
Option No.
3110‐0243
3110‐0244
3110‐0245
3110‐0246
3110‐0247
3110‐0248
3110‐0249
3110‐0250
3110‐0251
3110‐0252
3110‐0253
3110‐0254
3110‐0255
3110‐0256
3110‐0257
3110‐0258
3110‐0259
3110‐0260
Description
Bolt‐on diamond plate 16" tailboard (full width of body). For use with flat back style body. Includes handrails‐ (1) vertically on trailing edge of body opposite side of ladder and handrail(s) horizontally below hosebed.
Single Low Rear Compartment with Officer Side Storage Tunnel. For use with low hosebed. Includes smooth plate panels and storage access door with push button latch.
Bolt‐on diamond plate 18" tailboard (full width of body). Includes (2) squared off beavertails (no stanchions) with removable outer panels and handrails‐ (2) vertical on trailing edge of body and horizontal mounted handrail(s) below hosebed. Outer panels to be smooth plate painted job color.
Bolt‐on diamond plate 18" tailboard (full width of body). For use with rear ladder application. Includes handrails‐ (1) vertically on trailing edge of body opposite side of ladder and handrail(s) horizontally below hosebed.
Full Height Rear Compartment with Upper Storage Compartment and Officer Side Storage Tunnel. Includes smooth plate panels and storage access door with push button latch. Upper compartment to be approx 17" high x 38" wide x 26" deep.
Full Height Rear Compartment. Includes smooth plate panels, angled rear body with flip down tailboard and handrails‐ (2) vertical on trailing edge of body and horizontal mounted handrail(s) below hosebed.
Bolt‐on diamond plate 10" tailboard (full width of body). Includes handrails‐ (2) vertically on trailing edge of body. Must be used with hosebed dividers that include hand hold cut outs (the horizontally mounted handrail(s) are not included).
Top of body stepping surface plate work (compartment tops and enhanced extended compartment top at rear of body) shall be smooth plate painted black Durabak.
Full Height Rear Compartment with Officer Side Storage Tunnel. Includes flush smooth plate rear facing body panels and storage access door with push button latch.
PRICE
Enhanced extended exterior inside facing walls at either side of B1 compartment opening shall be smooth plate painted black durabak.
Full Height Rear Compartment with smooth plate panels. Compartment material to be 5083‐H321.
Single low rear compartment. For use with low hosebed. Includes smooth plate panels.
Full Height Rear Compartment 44" wide. Includes smooth plate panels.
Bolt‐on diamond plate 14" tailboard (full width of body). For use with dual rear ladder application. Includes handrail horizontally mounted below hosebed.
Rear Panel Compartment. Compartment B1, located centered ahead of the rear tailboard, shall be 46" wide x approximately 50" high x 26" deep. Solid walls shall be provided on both sides of the rear compartment. This compartment shall be of 12 gauge 304L stainless steel.
Rear Panel Area. The entire rear panel of the body shall be covered using smooth FRP panels for application of the Chevron graphics. The rear panel area shall be of the flat back body design.
Bolt‐on diamond plate 14" tailboard (full width of body). Includes handrails‐ (2) vertical on trailing edge of body and horizontal mounted handrail(s) below hosebed.
(1) officer side rear pump module extra width (inboard side) roof top compartment. Includes hinged raised compartment lid with turn latches and grab handle(s). Compartment to have (1) Amdor LED strip light and wired to door ajar indicator in cab. Outboard side of body to run full width and wrap around the rear and meet with the end of the hosebed end.
$629.00
$1,396.00
$1,196.00
$1,295.00
$1,789.00
$1,204.00
$1,214.00
$1,856.00
$1,698.00
$3,446.00
$1,087.00
$765.00
$1,379.00
$1,120.00
$1,327.00
$1,953.00
$1,232.00
$2,832.00
Option No.
3110‐0261
3110‐0262
3110‐0263
3110‐0264
3110‐0265
3110‐0266
3110‐0267
3110‐0268
3110‐0269
3110‐0273
3110‐0274
3110‐0275
3110‐0276
3110‐0277
3110‐0278
Description
(1) driver side rear pump module extra width (inboard side) roof top compartment (offset rearward and sized to allow deck gun to stow without interfering with hosebed area). Includes hinged raised compartment lid with turn latches and grab handle(s). Compartment to have (1) Amdor LED strip light and wired to door ajar indicator in cab. Outboard side of body to run full width and wrap around the rear and meet with the end of the hosebed.
Full Height Rear Compartment with Upper Storage Compartment and Officer Side Storage Tunnel. Upper Storage Compartment to be fully enclosed drop in / bolt in box with top. Compartment to be full height X full width of opening and 86" deep with a vertical partition located 26" from officer side. Driver side of partition to have a stop located 75" from box opening. Includes smooth plate panels and storage access doors with push button latches.
Lower Rear Compartment with Officer Side Storage Tunnel. Includes smooth plate panels and storage access door with push button latch. Includes bolt‐on panel between recessed traffic advisor and lower compartment for rear tank fill.
Lower rear stainless steel tall compartment B1, 46" wide x 60" high x 26" deep. Entire rear panel to be smooth FRP plate for Chevron graphics.
Bolt‐on diamond plate 16" tailboard full width of body with Bustin Tread. This provides a flat back body design. Includes hand rails, (2) vertically on trailing edge of body and horizontally mounted hand rail below hose bed.
Rear end tanker. Includes smooth plate upper and lower panels, a smooth plate center strip for a Jet or Newton Dump application, driver, and officer side access doors for storage tunnels.
Upper and Lower Rear Compartment. Includes smooth plate panels. Upper compartment to be as tall as possible (remove traffic advisor platework).
Bolt‐on diamond plate 12" tailboard 98" width Bustin Tread and Chicago style mitered corners. This provides a flat back body design. Includes hand rails, (2) vertically on trailing edge of body and horizontally mounted hand rail below hose bed.
Lower rear stainless steel short and narrow compartment B1, 26" wide x 35" high x 26" deep, for use with special lower rear panel plumbing options. Includes 46" wide intermediate rear step above. Entire rear panel to be smooth aluminum plate for Chevron graphics.
Full Height Rear Compartment with 4" high permanent diamond plate shelf for a Upper and Lower Rear Compartment design. Includes smooth plate panels. Upper compartment to be as tall as possible (remove traffic advisor platework).
Bolt‐on diamond plate 24" tailboard (full width of body). Includes (2) squared off 10" deep beavertails (no stanchions) with removable outer panels and handrails‐ (2) vertical on trailing edge of body and horizontal mounted handrail(s) below hosebed. For use with swivel style rear tank dump only.
Lower rear stainless steel tall compartment B1, 46" wide x approx. 64" high x 34" deep, door opening 53" high position. Includes bolt‐on intermediate step above the door opening. Entire rear panel to be smooth plate for Chevron graphics.
Lower Rear Compartment with access above to the ladders storage thru tank. Includes smooth plate panels and stepped upper horizontal tube to reduce hosebed height from ground over tank area.
Lower rear stainless steel short compartment B1, 46" wide x 40.25" high x 26" deep. Includes bolt‐on intermediate step above. Entire rear panel to be smooth aluminum plate for Chevron graphics.
Upper rear body panel below hose bed and above lower compartments to be brushed stainless steel (no chevron). Panel to be full width and includes the area behind the rear discharge pipes.
PRICE
$2,488.00
$5,215.00
$1,506.00
$1,320.00
$1,188.00
$846.00
$2,618.00
$1,306.00
$1,129.00
$2,618.00
$1,192.00
$1,688.00
$2,076.00
$1,120.00
$199.00
Option No.
3110‐0279
3110‐0280
3110‐0281
3110‐0282
3110‐0283
3110‐0284
3110‐0285
3110‐0286
3110‐0287
3110‐0288
3110‐0289
3110‐0290
3110‐0291
3110‐0292
3110‐0293
3110‐0294
Description
Bolt‐on diamond plate 20" tailboard (full width of body). Includes (2) slanted beavertails with lowered height approx 5.5" from standard to inhibit interferance as stowed with beacon lights as optioned (no stanchions) with removable outer panels and handrails‐ (2) vertical on trailing edge of body and horizontal mounted handrail(s) below hosebed.
Bolt‐on diamond plate 20" full width tailboard between rear side compartments with Bustin Tread. Includes hand rails (2) vertically on trailing edge of body and horizontally mounted hand rail below hose bed. Trailing edge of side compartments include 2" deep aluminum treadplate bumperettes to align tailboard to back of body.
Full Height Rear Compartment with Upper Storage Compartment and Side Storage Tunnel. Includes smooth plate panels and storage access doors with "D"‐ring latches.
Single low rear compartment. For use with low hosebed. Includes smooth plate panels. B1 compartment 28" deep.
Full Height Rear Compartment with Upper Ladder Storage Compartment. Includes smooth plate panels. Includes area for storage of (1) 24', (1) 14', (1) 10' Attic, (2) pike poles and a drop down storage access door with D‐Ring latch (wire to door ajar).
Bolt‐on diamond plate 18" tailboard (full width of body). Includes (2) slanted beavertails (no stanchions) with removable outer panels and handrails‐ (2) vertically on trailing edge of body.
The rearend area of the extra wide roof top compartment above the Zico access ladder to be recessed in 16". The stepping area to be embossed diamond plate and side and forward plates to be diamond plate.
Full Height Rear Compartment with Upper Storage Compartment and Officer Side Storage Tunnel. Includes smooth plate panels and storage access doors with "D"‐ring latches. Divider to be full length and be positioned 27" off of driver side compartment wall or as applicable close to fill tower on water tank. Area to the left of the divider to have a stop and be 84" deep. Area to the right of the divider to have a stop and be 75" deep.
Upper rear stainless steel short compartment B2, 36" wide x 16" high x 26" deep. Entire rear panel to be smooth FRP plate for Chevron graphics.
Bolt‐on diamond plate 12" tailboard full width of body with Bustin Tread, provides a flat back body design. Center section of step to be able to pull out and provide additional stepping surface. Includes hand rails, (2) vertically on trailing edge of body and horizontally mounted hand rail below hose bed.
Pumper rear mount rear end with lower pump panel provisions and upper pump maintenance access door with driver side ladder tunnel.
Includes smooth plate panels and storage access doors with D‐ring latches.
Bolt‐on diamond plate 12" tailboard (full width of body). For use with rear ladder application. Includes handrails‐ (1) vertical on trailing edge of body opposite side of ladder and handrail(s) horizontal below hosebed.
Single Low Rear Compartment with Officer Side Storage Tunnel. For use with low hosebed. Includes smooth plate panels and storage access door with d‐ring latch.
Rear Panel Compartment. Compartment B1, located centered ahead of the rear tailboard, shall be 46" wide x approximately 50" high x 32" deep. Solid walls shall be provided on both sides of the rear compartment. This compartment shall be of 12 gauge 304L stainless steel.
Bolt‐on diamond plate 12" tailboard full width of body with Bustin Tread. This provides a flat back body design. Includes hand rails, (2) vertically on trailing edge of body and NO horizontally mounted hand rail below hose bed.
Lower rear stainless steel short compartment B1, 46" wide x 35" high x 26" deep, without an intermediate rear step for hinged doors. Entire rear panel to be smooth aluminum plate for Chevron graphics.
PRICE
$1,318.00
$1,195.00
$2,296.00
$1,032.00
$2,288.00
$1,070.00
$796.00
$2,330.00
$904.00
$2,516.00
$1,265.00
$1,056.00
$1,204.00
$1,327.00
$1,045.00
$895.00
Option No.
3110‐0295
3110‐0296
3110‐0297
3110‐0298
3110‐0299
3110‐0300
3110‐0301
3110‐0302
3110‐0303
3110‐0304
3110‐0305
3110‐0306
3110‐0307
3110‐0308
3110‐0309
Description
HS pumper / rescue pumper rear body with officer side storage tunnel. Includes center radiator mesh, smooth plate panels and storage access door with push button latch.
Lower Rear Compartment only. Upper section to be smooth plate panel. Includes smooth plate panels.
HS pumper / rescue pumper rear body. Includes center radiator mesh and smooth plate panels.
Full Height Rear Compartment with Upper Ladder Storage Compartment. Includes smooth plate panels. Includes area for storage of (1) 28', (1) 14', (1) 10' Attic, (1) Dry wall hook, (2) pike poles and a drop down storage access door with push buton latches (wire to door ajar).
1" X 1.5" extrusion added to lower B1 compartment door opening to form a 10" wide notch offset to officer side for 5" LDH hose connected to customer supplied and installed valve stored in B1. This will also require floor mounted rollout tray to be raised to clear lower door opening.
Full Height Rear Pump Panel Compartment with officer side ladder tunnel storage with smooth plate door secured with D‐Ring style latch. Includes smooth plate panels, angled rear body with flip down tailboard and handrails as applicable. Pump Panels to be recessed in the rear body and enclosed on all sides.
Bolt‐on diamond plate 10" tailboard (full width of body) with center integral slide‐out step. Includes handrails‐ (1) vertical on trailing edge of body opposite side of ladder and handrail(s) horizontal below hosebed.
Full Height Rear Compartment with Upper Ladder Storage Compartment. Includes smooth plate panels. Includes area for storage of (1) 24', (1) 14', (1) 10' Attic, (2) NY Roof Hook style pike poles and a drop down storage access door with push buton latches (wire to door ajar).
Full Height Rear Compartment with Driver and Officer Side Storage Tunnels. Includes smooth plate panels and storage access doors with push button latches tied to door ajar. Rear compartment to be dual purpose and equipped with a 22" wide door opening on the driver side and a rear body panel added in the remaining space for a rear slam strip to accommodate a jet dump and a direct tank fill in the lower officer side area of the rear compartment. Upper area above slam strip to include a vertical hinged access door of smooth plate aluminum matching rear of body selected finish with stainless steel hinge, push button latch and rubber impact bumper to cushion door on handrail in open position.
Full Height Rear Pump Panel Compartment. Includes smooth plate panels, angled rear body with flip down tailboard and handrails as applicable. Pump Panels to be recessed in the rear body and enclosed on all sides.
Lower rear stainless steel tall compartment B1, 46" wide x 45" high x 26" deep without intermediate step above. Entire rear panel to be smooth aluminum plate for Chevron graphics.
Lower Rear Compartment with Officer Side Storage Tunnel. Includes smooth plate panels and storage access door with "D"‐ring.
Rearend assembly with 3/4 height rear end and (3) dry chemical access doors. The upper access areas to the center section to provide access to the dry chemical vessel and two access doors to the nitorgen bottle(s). For use with Industrial products only.
Upper rear stainless steel short compartment B2, 39" wide x 12" high x 26" deep. Entire rear panel to be smooth FRP plate for Chevron graphics.
Bolt‐on 3/16" (.1875") smooth plate painted black Durabak 10" tailboard (full width of body). For use with rear ladder application. Includes handrails‐ (1) vertical on trailing edge of body opposite side of ladder and handrail(s) horizontal below hosebed.
PRICE
$1,765.00
$1,120.00
$1,592.00
$2,208.00
$375.00
$5,505.00
$2,128.00
$2,208.00
$2,807.00
$5,299.00
$1,070.00
$1,328.00
$972.00
$904.00
$1,217.00
3110‐0311
Description
Full height rear compartment with upper ladder storage compartment. Includes smooth plate panels. Includes area for storage of (1) 24',(1)14',(1)10' attic, (3) pike poles, including (1) one each 6', 8' and 10' with APH style hooks, a lift up storage access door with hold open springs and push button latches (wire to door ajar) note door to open up 90 degrees. There shall be label 'DO NOT STEP' to be applied "upside down" as viewed from the ground at the bottom of the lift‐up door.
Bolt‐on diamond plate tailboard (full width of rear compartment). 20" tailboard to run full width of body ("T" shaped tailboard). Includes the extended side compartment frame work and handrails‐ (2) vertical on trailing edge of body and horizontal mounted handrail(s) below hosebed.
3110‐0312
Bolt‐on diamond plate 18" tailboard (full width of body). Includes (2) slanted beavertails (no stanchions) with removable outer smooth plate panels painted job color and handrails‐ (2) vertically on trailing edge of body and horizontally mounted handrail(s) below hosebed.
Option No.
3110‐0310
3110‐0313
3110‐0314
3110‐0315
3110‐0316
3110‐0317
3110‐0318
3110‐0319
3110‐0320
3110‐0321
3110‐0322
3110‐0323
3110‐0324
3110‐0325
3110‐0326
3110‐0327
Full Height Rear Compartment with Driver Side Storage Tunnel. Includes smooth plate panels and storage access door with D‐ring latch.
Rear flip down tailboard to be painted Durabak black. Includes indicator in cab when the tailboard is in the down position. Includes handrails‐ (2) vertically on trailing edge of body and horizontally mounted handrail(s) below hosebed.
Upper rear compartment depth to be approximately 40" deep.
Lower Rear Compartment only 46" wide opening. Upper section to be smooth plate panel. Includes smooth plate panels.
Rear flip down tailboard. Includes indicator in cab when the tailboard is in the down position. Includes handrails‐ (1) vertical on trailing edge of body opposite side of ladder and handrail(s) horizontal below hosebed.
Upper and lower rear compartment. Includes smooth plate panels. For use with raised lower rear body (B1 is 29" high).
Handrails on rear of body below hosebed IPO standard hand rail. Includes (2) horizontally mounted handrails with offset stanchions. (1) each side of the camera below hosebed.
Full Height Rear Compartment with Officer Side Storage Tunnel. Rear tank fill to terminate above rear compartment thru a bolt‐on access panel. Includes smooth plate panels and storage access door with push button latch.
Rear end tanker. Includes smooth plate upper and lower panels and a smooth plate center strip for a Newton Dump application.
Lower rear stainless steel short compartment B1, for hose reel.
Bolt‐on diamond plate 12" tailboard full width of body with Bustin Tread. This provides a flat back body design. Includes hand rails, (2) vertically on trailing edge of body and horizontally mounted hand rail below hose bed.
Full Height Rear Compartment with Driver Side Storage Tunnel. Includes smooth plate panels and storage access door with "D"‐ring latch.
Bolt‐on diamond plate tailboard (full width of rear compartment). Includes the rear beavertail compartments and handrails‐ (2) vertical on trailing edge of body and horizontal mounted handrail(s) below hosebed.
Bolt‐on diamond plate tailboard (full width of rear compartment). Additional 10" of tailboard to run full width of body ("T" shaped tailboard). Includes the enhanced extended side compartment frame work and handrails‐ (2) vertical on trailing edge of body. Does not include the horizontal handrail.
Rear body panels to be upgraded from smooth aluminum plate to aluminum treadplate. This includes the doors for ladder and storage tunnels (if applicable). For use with dealer/customer installed rear panel chevron.
PRICE
$2,422.00
$1,856.00
$2,031.00
$1,247.00
$4,907.00
$291.00
$1,292.00
$3,926.00
$1,843.00
$0.00
$1,592.00
$843.00
$1,120.00
$1,087.00
$1,204.00
$2,432.00
$2,432.00
$706.00
Option No.
3110‐0328
3110‐0329
3110‐0330
3110‐0331
3110‐0332
3110‐0333
3110‐0334
3110‐0335
3110‐0336
3110‐0337
3110‐0338
3110‐0339
3110‐0340
3110‐0341
3110‐0342
3110‐0343
3110‐0344
Description
Bolt‐on diamond plate 16" tailboard with Bustin Tread (full width of body). Includes (2) slanted beavertails and hand rails, (2) vertically on trailing edge of body and horizontally mounted hand rail below hose bed.
Full Height Rear Compartment with Upper Ladder Storage Compartment. Includes smooth plate panels. Includes area for storage of (1) 24 '/ 2section, (1) 16' roof, (1) 10' Attic, (3) pike poles with a drop down storage access door with push button latches (wire to door ajar).
Single low rear compartment. B1 compartment to be 30" deep and non transverse. For use with low hosebed. Includes smooth plate panels.
Lower rear stainless steel short compartment B1 between full length chassis frame rails with drop‐down door, 26.5" wide x 14.5" high x 26" deep. Includes bolt‐on intermediate step above. Entire rear panel to be smooth aluminum plate for Chevron graphics.
Bolt‐on diamond plate 10" tailboard (full width of body). Includes (2) squared off beavertails (no stanchions) with removable outer panels and handrails‐ (2) vertical on trailing edge of body and horizontal mounted handrail(s) below hosebed.
Enclosed Rear Pump Panel on Rear Mount. Includes 40" wide pump panel opening. Upper module area to have embossed diamond plate top.
Bolt‐on diamond plate 14" tailboard (full width of body). For use with rear ladder application. Includes handrails‐ (1) mounted vertical on trailing edge of body opposite side of ladder and handrail(s) horizontal below hosebed. Gator grip to be on each end outboard of the rear pump panel enclosure.
Rear Compartment between frame rails. Includes bottom hinged drop‐down access door using a D‐ring latch (wire to door ajar).
The rearend area of the extra wide roof top compartment above the Zico access ladder to be recessed in 16". The stepping surface to be embossed diamond plate, side plates to be diamond plate and forward plate to be sanded smooth plate.
Full Height Rear Compartment with Officer Side Combination Storage Tunnel. Includes smooth plate panels and storage access doors with d‐ring latches.
Full Height Rear Compartment with Upper Ladder Storage Compartment. Includes smooth plate panels. Includes area for storage of (1) 24', (1) 14', (1) 10' Attic, (3) pike poles and a drop down storage access door with push button latches (wire to door ajar).
Bolt‐on diamond plate 14" tailboard (full width of body). For use without a rear ladder application. Includes handrails‐ (2) mounted vertical on trailing edge of body and handrail(s) horizontal below hosebed.
Full Height Rear Compartment with Driver Side Combination Storage Tunnel. Includes smooth plate panels and storage access doors with d‐ring latches.
Pumper rear mount rear end with lower pump panel provisions and upper pump maintenance access door with officer side ladder tunnel. Includes smooth plate panels and storage access doors with push button latches.
Lower rear stainless steel compartment B1, 24" wide x 20" high x 26" deep, located between full length chassis frame rails. For use with special lower rear panel plumbing options with a low hose bed design. Entire rear panel to be smooth aluminum plate for Chevron graphics. No intermediate step above.
(1) bolt‐on compartment 17" W x 40" H x 11" D. Locate on the driver side of rear step and to have 15" wide opening. The compartment includes a vertically hinged smooth plate door (with 4" gap at top for connecting of hose stored in compartment) with D‐ring latch (wired into door ajar indicator), removable Duradek flooring and embossed non‐skid treadplate compartment top. Lower hose bed access steps to be mounted to inboard side of compartment.
Rear body panels to be upgraded from smooth aluminum plate to painted smooth FRP.
PRICE
$953.00
$2,255.00
$1,032.00
$914.00
$1,835.00
$1,807.00
$1,120.00
$1,014.00
$796.00
$2,749.00
$2,381.00
$1,120.00
$2,749.00
$1,265.00
$902.00
$1,056.00
$289.00
Option No.
3110‐0345
3110‐0346
3110‐0347
3110‐0348
3110‐0349
3110‐0350
3110‐0351
3110‐0352
3110‐0353
3110‐0354
3110‐0355
3110‐0356
3110‐0357
3110‐0358
3110‐0359
3110‐0360
Description
Full Height Rear Compartment with Officer Side Storage Tunnel. Includes smooth plate panels and storage access door with push button latch. The B1 compartment to be 40" wide, full depth (no compartment break) and as tall as possible.
The rearend area of the extra wide roof top compartment above the Zico access ladder to be recessed in 16in. The stepping area to be embossed diamond plate and side and forward plates to be smooth plate painted job color.
Rear body panels to be unpainted smooth FRP. For use with full width rear chevron applications.
Bolt‐on diamond plate 22" tailboard with Bustin Tread (full width of body). Includes (2) squared off beavertails with hand rails, (2) vertically on trailing edge of body and horizontally mounted hand rail below hose bed.
(1) bolt‐on compartment 19" W x 36" H x 20" D. Locate on the officer side of rear step and to have 17" wide opening. The compartment includes a vertically hinged smooth plate door (with 4" gap at top for connecting of hose stored in compartment) with D‐ring latch (wired into door ajar indicator), removable Duradek flooring and embossed non‐skid treadplate compartment top. Lower hose bed access steps to be mounted to inboard side of compartment.
((1) bolt‐on compartment 17" W x 36" H x 20" D. Locate on the driver side of rear step and to have 15" wide opening. The compartment includes a vertically hinged smooth plate door (with 4" gap at top for connecting of hose stored in compartment) with D‐ring latch (wired into door ajar indicator), removable Duradek flooring and embossed non‐skid treadplate compartment top. Lower hose bed access steps to be mounted to inboard side of compartment.
Lower rear stainless steel narrow compartment B1 opening, approximately 29" wide. For use with special lower rear step compartment options.
Bolt‐on diamond plate tailboard (full width of driver side hosebed to officer side rear compartment). Includes the enhanced extended officer side compartment frame work. Driver side includes (1) upper hosebed mounted handrail (as applicable) and handrails‐ (2) vertically on trailing edge of body and horizontally mounted handrail(s) below hosebed.
Bolt‐on diamond plate 22" full width tailboard between rear side compartments with Bustin Tread. Includes hand rails (2) vertically on trailing edge of body and horizontally mounted hand rail below hose bed. Trailing edge of side compartments include 4" deep aluminum treadplate bumperettes to align tailboard to back of body.
Lower rear stainless steel short compartment B1, transverse access, 46" wide x 35" high x 26" deep. Includes bolt‐on intermediate step above. Entire rear panel to be smooth aluminum plate for Chevron graphics.
Angled (Boston style) style tailboard corners. 8" x 8" cutouts to be provided.
Bolt‐on diamond plate tailboard 10 in. (full width of Body). Includes hose bed structure extended to rear of body over side enhanced compartments for a smooth back body and provide a max depth B1 compartment as optioned. With handrails‐ (2) vertical on trailing edge of body or (1) if a Zico ladder is equipped and horizontal mounted handrail(s) below hosebed.
Single low rear compartment. For use with low hosebed. Includes smooth plate panels.
Full Height Rear Compartment with Upper Ladder Storage Compartment. Includes smooth plate panels. Includes area for storage of (1) 24', (1) 14', (1) 10' Attic, (2) pike poles and a drop down storage access door with push button latches (wire to door ajar).
LINE‐X package for welded (exterior surface only), bolt on (exterior surface only) or flip down style (exterior and interior surfaces) tailboards. Includes rear bumper overlay or E‐ONE fabricated boxes mounted on the tailboard as applicable.
Rear of body to have un‐painted smooth plate overlay style body panels to facilitate rear body striping.
PRICE
$1,204.00
$958.00
$183.00
$1,118.00
$1,298.00
$1,262.00
$0.00
$903.00
$1,195.00
$1,120.00
$482.00
$2,551.00
$1,032.00
$2,208.00
$273.00
$1,379.00
Option No.
3110‐0361
3110‐0362
3110‐0363
3110‐0364
3110‐0365
3110‐0366
3110‐0367
3110‐0368
3110‐0369
3110‐0370
3110‐0371
3110‐0372
3110‐0373
3110‐0374
Description
Lower rear stainless steel short and narrow compartment B1, 46" wide x 30" high x 28" deep, for use with special lower rear panel plumbing options. Left side wall removed to allow for ALS module passage from L3. This compartment shall not have an exterior door opening. Entire rear panel to be smooth aluminum plate for Chevron graphics.
Upper rear stainless steel short/narrow compartment B2, 23" wide x 10" high x 43" deep. Includes a 3‐sided floor mounted 1/2" thick Poly tray, open to the front (door opening).
Full Height Rear Compartment with Full Width Upper Storage Compartment. Includes officer side area for storage of (1) Ice Sled approx. 28"W X 6"H X 86"L with stops set at 88" from inside door opening and a drop down smooth plate storage access door with push buton latches (wire to door ajar). Door to be as wide as B1 compartment opening. Includes driver side area for storage of (2) 6" X 10' Hard Suction Hoses with stops set at 130" from inside door opening and a drop down smooth plate storage access door with push buton latches (wire to door ajar). Includes (1) divider located 30" off officer's side door opening. Includes smooth plate panels.
Bolt‐on diamond plate 10" tailboard (full width of body) with center integral slide‐out step. Includes handrails‐ (2) mounted vertical on trailing edge of body and horizontal mounted handrail(s) below hosebed.
Bolt‐on diamond plate 12" tailboard (full width of body). For use with folding step application. Includes handrails‐ (1) vertical on trailing edge of body opposite each side of body and handrail(s) horizontal below hose bed.
Lower rear stainless steel short compartment B1, 46" wide x 35" high x 26" deep. Includes bolt‐on intermediate step above FULL WIDTH BETWEEN HANDRAILS (less 2" each side for grab rail use). Entire rear panel to be smooth aluminum plate for Chevron graphics.
Bolt‐on diamond plate tail board 14 in. (full width of Body). Includes hose bed structure extended to rear of body over side enhanced compartments for a smooth back body and provide a max depth B1 compartment as optioned. With handrails‐ (2) vertical on trailing edge of body or (1) if a Zico ladder is equipped and horizontal mounted handrail(s) below hosebed.
Full Height Rear Compartment with Upper Ladder Storage Compartment. Includes smooth plate panels. Includes area for storage of (1) 24', (1) 14', (1) 10' Attic, (4) pike poles and a drop down storage access door with push button latches (wire to door ajar).
The rearend area of the extra wide roof top compartment above the Zico access ladder to be recessed in 16". The stepping area to be embossed diamond plate and side plates to be diamond plate and the forward plate to be smooth plate.
Rear end tanker. Includes smooth plate full width upper and side lower panels and a smooth plate center area for mounting of rear tank inlet(s) application.
(2) bolt‐on compartments. Locate (1) each side of B1. Each compartment includes a hinged smooth plate door (with 4" gap at top for connecting of hose stored in compartment) with push button latch (wired into door ajar indicator), removable slat flooring and Gator Grip compartment top. Lower hosebed access step (one each side) to be mounted to inboard side of compartment.
Full Height Rear Compartment with Upper Ladder Storage Compartment. Includes smooth plate panels. Includes area for storage of (1) 24', (1) 14', (1) 10' Attic, (2) pike poles and a drop down storage access door with D‐ring latches (wire to door ajar).
Bolt‐on diamond plate 24" tailboard with Bustin Tread (full width of body). Includes (2) slanted beavertails with removable outer panels and hand rails (2) vertically on trailing edge of body and horizontally mounted hand rail below hose bed.
Full Height Rear Pump Panel Compartment with officer side ladder tunnel storage with smooth plate door secured with D‐Ring style latch. Includes smooth plate panels, angled rear body with flip down tailboard and handrails as applicable.
PRICE
$1,129.00
$1,332.00
$2,625.00
$2,128.00
$1,056.00
$1,275.00
$2,751.00
$2,208.00
$796.00
$649.00
$1,850.00
$2,256.00
$1,181.00
$4,505.00
Option No.
3110‐0375
3110‐0376
3110‐0377
3110‐0378
3110‐0379
3110‐0380
3110‐0381
3110‐0382
3110‐0383
3110‐0384
3110‐0385
3110‐0386
3110‐0387
3110‐0388
3110‐0389
Description
Rear stainless steel extra tall compartment B1, 46" wide x 60" high x 26" deep. Includes bolt‐on intermediate step above. Entire rear panel to be smooth aluminum plate for Chevron graphics.
Lower rear stainless steel compartment B1, 26.5" wide x 14.5" high x 26" deep, located between full length chassis frame rails. Entire rear panel to be smooth aluminum plate for Chevron graphics. Does not include an intermediate step. Includes a smooth aluminum bottom hinged drop‐down door and stainless steel bent D‐ring latch.
Full Height Rear Compartment. Includes smooth plate panels. Includes stepped upper horizontal tube to reduce hosebed height from ground over tank area.
Center Slam Strip Rear End with diamond plate center strip for a Jet or Newton Dump application. Includes diamond plate low side panels and diamond plate upper panel(s). Requires rear NFPA striping compatible for diamond plate panels.
Upper Storage Compartment to hold (1) 10' attic ladder, (1) 6' pike pole, (1) 12' pike pole and (1) 8' NY pike pole and (2) 6" x 10' hard suction hoses. Includes stop bracket included approximately 130" back from opening. An enclosed frontal area shall be included as part of the tunnel design. Storage shall be enclosed with drop down door with D‐Ring latch(es).
Lower Rear Compartment 40" high with Officer Side Storage Tunnel. Includes smooth plate panels and storage access door with D‐Ring latch.
Single low rear compartment. For use with low hosebed. Includes smooth plate panels.
(2) bolt‐on compartments. Locate (1) each side of B1. Each compartment includes a hinged smooth plate door (with 4" gap at top for connecting of hose stored in compartment) with D‐ring style latch (wired into door ajar indicator), removable slat flooring and Gator Grip compartment top. Lower hosebed access step (one each side) to be mounted to inboard side of compartment.
Lower rear stainless steel short compartment B1, 46" wide x 35" high x 25" deep (for fuel tank clearance). Includes bolt‐on intermediate step above FULL WIDTH BETWEEN HANDRAILS (less 2" each side for grab rail use). Entire rear panel to be smooth aluminum plate for Chevron graphics.
Rear of body to have un‐painted extrusions with un‐painted smooth plate overlay style body panels to facilitate rear body striping. (For use with HM100/110 NPNT and center hosebed HM100/110, HP100,CR100/137, HPS105, 95‐P only)
2) bolt‐on compartments. Locate (1) each side of B1 ‐ driver side to have 13" wide x 34" high opening and officer side to have 17" wide x 29" high opening. Each compartment to be 20" deep. Each compartment includes a hinged smooth plate door (with 4" gap driver side only at top for connecting of hose stored in compartment) with D‐Ring latch (wired into door ajar indicator), removable slat flooring and Embossed Diamond Plate compartment top. Lower hosebed access step (one on the driver side and one on the officer side) to be mounted to inboard side of compartment.
Full Height Rear Compartment with Officer Side Storage Tunnel. Includes smooth plate panels and storage access door with D‐Ring. B1 compartment opening to be 34" wide due to officer side tailboard compartment.
The rearward area of the extra wide roof top compartment above the Zico access ladder to be recessed in 16". The stepping surface to be embossed diamond plate, side plates to be diamond plate and forward plate to be FRP smooth plate.
Full Height Rear Compartment with Officer Side Storage Tunnel. Includes lower smooth plate panels and upper diamond plate panels and storage access door with "D"‐ring latch.
Full Height Rear Compartment with Upper Ladder Storage Compartment. Includes smooth plate panels. Includes area for storage of (1) 24', (1) 16', (1) 10' Attic, (2) pike poles and a drop down storage access door with push button latches (wire to door ajar).
PRICE
$1,295.00
$988.00
$2,208.00
$2,104.00
$798.00
$1,328.00
$1,032.00
$1,850.00
$1,275.00
$267.00
$1,993.00
$1,377.00
$796.00
$1,719.00
$2,208.00
Option No.
3110‐0390
3110‐0391
3110‐0392
3110‐0393
3110‐0394
3110‐0395
3110‐0396
3110‐0397
3110‐0398
3110‐0399
3110‐0400
3110‐0401
3110‐0402
3110‐0403
3110‐0404
3110‐0405
3110‐0406
3110‐0407
Description
The rearend area of the extra wide roof top compartment above the folding steps to be recessed in 16". The stepping area to be embossed diamond plate and side and forward plates to be diamond plate.
Bolt‐on diamond plate tailboard (full width of rear compartment). Additional 12in. of tailboard to run full width of body ("T" shaped tailboard). Includes the enhanced extended side compartment frame work and handrails‐ (2) vertical on trailing edge of body as applicable and horizontal mounted handrail(s) below hose bed.
Full Height Rear Compartment with Officer Side Storage Tunnel. Hosebed extrusion to be stepped for storage tunnel if applicable. Includes smooth plate panels and storage access door with D‐ring latch.
Full Height Rear Compartment with Officer Side Storage Tunnel. Includes smooth plate panels and horizontally hinged storage access door with push button latch and rubber bumpers.
Single Low Rear Compartment with Upper Storage Compartment and Officer Side Storage Tunnel. For use with low hosebed. Includes smooth plate panels and storage access door with push button latch.
Lower rear stainless steel short compartment B1, transverse access, 46" wide x 35" high x 26" deep without an intermediate step above. Entire rear panel to be smooth aluminum plate for Chevron graphics.
Rear End with no rear compartment and officer side storage tunnel. Includes smooth plate panels and storage access door with d‐ring latch.
Full Height Rear Compartment with Upper Ladder Storage Compartment. Includes smooth plate panels. Includes area for storage of (1) 35', (1) 14', (1) 10' Attic, (2) pike poles and a drop down storage access door with push button latches (wire to door ajar).
Bolt‐on diamond plate 8" tailboard (full width of body). Includes handrails‐ (2) mounted vertical on trailing edge of body and horizontal mounted handrail(s) below hosebed.
Upper and lower rear compartment. Includes smooth plate panels. For use with raised lower rear body (B1 is 34" high).
Lower rear stainless steel narrow short compartment B1, 37" wide x 35" high x 26" deep, offset to the driver's side to allow for rear panel plumbing options. Includes bolt‐on intermediate step above. Entire rear panel to be smooth aluminum plate for Chevron graphics.
Bolt‐on diamond plate 18" tailboard (full width of body). Includes (2) squared off 11.25" deep beavertails (no stanchions) with removable outer panels and handrails‐ (2) vertical on trailing edge of body and horizontal mounted handrail(s) below hosebed. For use with swivel style rear tank dump only.
Bolt‐on diamond plate tailboard (full width of rear compartment). Additional 7" of tailboard to run full width of body ("T" shaped tailboard). Includes the enhanced extended side compartment frame work and handrails per NFPA requirement.
Handrails, extruded aluminum, installed full length on outboard top edge of driver roof top compartment lids.
Full Height Rear Compartment with Upper Storage Compartment and Officer Side Storage Tunnel. Includes smooth plate panels and storage access doors with push button latches.There shall be smooth plate panels each side of upper storage drop down door for rear discharges. Includes a stop bracket approximately 130" back from opening.
Bolt‐on diamond plate 14" tailboard (full width of body). Includes (2) slanted beavertails (no stanchions) with removable outer panels and handrails‐ (2) vertically on trailing edge of body and horizontally mounted handrail(s) below hosebed.
Full Height Rear Compartment with Upper Ladder Storage Compartment. Includes smooth plate panels. Includes area for storage of (1) 35' 3‐section ladder and a drop down storage access door with push button latches (wire to door ajar).
Single low rear compartment. For use with low hosebed. Includes smooth plate panels. This is a non transverse compartment.
PRICE
$796.00
$2,432.00
$1,419.00
$1,204.00
$3,204.00
$1,007.00
$837.00
$2,208.00
$1,087.00
$1,843.00
$1,120.00
$1,192.00
$2,432.00
$588.00
$2,989.00
$1,264.00
$2,208.00
$1,032.00
Option No.
3110‐0408
3110‐0409
3110‐0410
3110‐0411
3110‐0412
3110‐0413
3110‐0414
3110‐0415
3110‐0416
3110‐0417
3110‐0418
3110‐0419
3110‐0420
3110‐0421
3110‐0422
3110‐0448
3120‐0000
Description
Full Height Rear Compartment with Officer Side Storage Tunnel. Includes smooth plate panels and storage access door with push D‐ring style latch. Includes stepped upper horizontal tube to reduce hosebed height from ground over tank area.
Rear Panel Compartment. Compartment B1, located centered ahead of the rear tailboard, shall be 46" wide x approximately 36" high x 26" deep. Solid walls shall be provided on both sides of the rear compartment. This compartment shall be of 12 gauge 304L stainless steel.
Bolt‐on diamond plate 10" tailboard (full width of body). Includes handrail ‐ (1) vertically on driver side trailing edge of body and horizontally mounted handrail(s) below hosebed.
Bolt‐on diamond plate 18" tailboard with Bustin Tread (full width of body). Includes (2) squared off beavertails with hand rails, (2) vertically on trailing edge of body and horizontally mounted hand rail below hose bed.
Rear end tanker. Includes smooth plate upper and lower panels, and driver side access door for storage tunnel with D‐ring latch.
The rearward area of the extra wide roof top compartment above the rear panel folding steps on the driver side be recessed in 16". The stepping surface to be embossed diamond plate, side plates to be diamond plate and forward plate to be FRP smooth plate.
Bolt‐on diamond plate 12" tailboard full width of body with Bustin Tread. This provides a flat back body design. Includes hand rails, (2) vertically on trailing edge of body and horizontally mounted hand rail below hose bed. Includes a bolted double C‐channel mounting structure.
Angled 6" x 6" (Boston style) style tailboard corners.
Upper rear stainless steel short/narrow compartment B2, 23" wide x 10" high x 36" deep. Includes a 3‐sided floor mounted 1/2" thick poly tray, open to the front (door opening).
Bolt‐on diamond plate 16" tailboard full width of body with Bustin Tread. This provides a flat back body design. Includes (1) vertically mounted handrail on the trailing edge of officer side of body and horizontally mounted handrail below hose bed. For use with driver side ladder.
Full Height Rear Compartment with Upper Storage Compartment. Includes smooth plate panels. Includes area for storage of (1) Washington‐Ferno Stokes basket offset to officer side with stop set at 86" from opening, storage for (1) backboard above stokes basket with stop set at 74" from opening, misc. storage for long handle tools offset to driver side and a drop down storage access door with push buton latches (wire to door ajar).
Single Low Rear Compartment with Driver Side Storage Tunnel. For use with low hosebed. Includes smooth plate panels and storage access door with d‐ring latch. B1 compartment opening to be narrowed and offset to driver side with a rear slam strip offset to officer side for rear plumbing to exit without being inside B1 compartment.
Tanker body rear end sheet metal will be configured with inner plates to be smooth plate, both upper and lower. Outer plates and any storage tunnel doors to be diamond plate.
Full Height Rear Compartment 42" wide. Includes smooth plate panels.
The rearend area of the extra wide roof top compartment above the Zico access ladder to be recessed in 24". The stepping area to be embossed diamond plate and side and forward plates to be diamond plate.
Rear ladder tunnel door. Vertically hinged diamond plate ilo standard. Door to hinge to drivers sides and include D‐ring latch.
Officer half side body with 24" wide forward and 36" wide rearward compartmentation. Includes adjustable ladder tracks.
PRICE
$2,352.00
$1,126.00
$1,087.00
$1,011.00
$846.00
$796.00
$1,087.00
$482.00
$1,332.00
$1,188.00
$3,313.00
$1,504.00
$400.00
$1,295.00
$796.00
$730.00
$4,493.00
Option No.
Description
PRICE
3120‐0001
3120‐0003
3120‐0004
3120‐0005
3120‐0006
Officer half side body with 24" wide forward and 50" wide rearward extended compartmentation. Includes adjustable ladder tracks.
Officer half side body with 30" wide forward and 36" wide rearward compartmentation. Includes adjustable ladder tracks.
Officer half side body with 36" wide forward and 36" wide rearward compartmentation. Includes adjustable ladder tracks.
Officer half side body with 42" wide forward and 42" wide rearward compartmentation. Includes adjustable ladder tracks.
Officer half side body with 48" wide forward and 48" wide rearward compartmentation. Includes adjustable ladder tracks.
$5,123.00
$4,809.00
$5,147.00
$5,504.00
$5,890.00
3120‐0007
Officer half side body with 30" wide forward and 50" wide rearward extended compartmentation. Includes adjustable ladder tracks.
$5,436.00
3120‐0008
Officer half side body with 36" wide forward and 50" wide rearward extended compartmentation. Includes adjustable ladder tracks.
$5,773.00
3120‐0009
Officer half side body with 42" wide forward and 56" wide rearward extended compartmentation. Includes adjustable ladder tracks.
$6,135.00
3120‐0010
Officer half side body with 48" wide forward and 62" wide rearward extended compartmentation. Includes adjustable ladder tracks.
Officer half side body with 24" wide forward and 50" wide rearward enhanced extended compartmentation. Includes adjustable ladder tracks.
Officer half side body with 30" wide forward and 50" wide rearward enhanced extended compartmentation. Includes adjustable ladder tracks.
Officer half side body with 36" wide forward and 50" wide rearward enhanced extended compartmentation. Includes adjustable ladder tracks and ladder brackets.
Officer half side body with 42" wide forward and 56" wide rearward enhanced extended compartmentation. Includes adjustable ladder tracks.
Officer half side body with 48" wide forward and 62" wide rearward enhanced extended compartmentation. Includes adjustable ladder tracks.
Officer 3/4 side body with upper and lower compartmentation. Includes 24" wide forward and 36" wide rearward lower compartments and (3) opening upper compartments.
Officer 3/4 side body with full height 24" wide forward and 36" wide rearward compartmentation. Includes (1) 56" wide compartment over the wheel well.
Officer 3/4 side body with upper and lower compartmentation. Includes 30" wide forward and 36" wide rearward lower compartments and (3) opening upper compartments.
Officer 3/4 side body with upper and lower compartmentation. Includes 36" wide forward and 36" wide rearward lower compartments and (3) opening upper compartments.
Officer 3/4 side body with upper and lower compartmentation. Includes 42" wide forward and 42" wide rearward lower compartments and (3) opening upper compartments.
Officer 3/4 side body with upper and lower compartmentation. Includes 48" wide forward and 48" wide rearward lower compartments and (3) opening upper compartments.
$6,519.00
3120‐0011
3120‐0012
3120‐0013
3120‐0014
3120‐0015
3120‐0016
3120‐0017
3120‐0018
3120‐0019
3120‐0020
3120‐0021
$5,412.00
$5,724.00
$6,060.00
$6,420.00
$6,806.00
$6,065.00
$5,617.00
$6,458.00
$6,878.00
$7,328.00
$7,810.00
Option No.
3120‐0022
3120‐0023
3120‐0024
3120‐0025
3120‐0026
3120‐0027
3120‐0028
3120‐0029
3120‐0030
3120‐0031
3120‐0032
3120‐0033
3120‐0034
3120‐0035
3120‐0036
3120‐0037
3120‐0038
3120‐0039
Description
Officer 3/4 side body with full height 30" wide forward and 36" wide rearward compartmentation. Includes (1) 56" wide compartment over the wheel well.
Officer 3/4 side body with full height 36" wide forward and 36" wide rearward compartmentation. Includes (1) 56" wide compartment over the wheel well.
Officer 3/4 side body with full height 42" wide forward and 42" wide rearward compartmentation. Includes (1) 56" wide compartment over the wheel well.
Officer 3/4 side body with full height 48" wide forward and 48" wide rearward compartmentation. Includes (1) 56" wide compartment over the wheel well.
Officer 3/4 side body with 24" wide forward and 50" wide rearward extended compartmentation. Includes (1) 56" wide compartment over the wheel well.
Officer 3/4 side body with 30" wide forward and 50" wide rearward extended compartmentation. Includes (1) 56" wide compartment over the wheel well.
Officer 3/4 side body with 36" wide forward and 50" wide rearward extended compartmentation. Includes (1) 56" wide compartment over the wheel well.
Officer 3/4 side body with 42" wide forward and 56" wide rearward extended compartmentation. Includes (1) 56" wide compartment over the wheel well.
Officer 3/4 side body with 48" wide forward and 62" wide rearward extended compartmentation. Includes (1) 56" wide compartment over the wheel well.
Officer 3/4 side body with 24" wide forward and 50" wide rearward enhanced extended compartmentation. Includes (1) 56" wide compartment over the wheel well.
Officer 3/4 side body with 30" wide forward and 50" wide rearward enhanced extended compartmentation. Includes (1) 56" wide compartment over the wheel well.
Officer 3/4 side body with 36" wide forward and 50" wide rearward enhanced extended compartmentation. Includes (1) 56" wide compartment over the wheel well.
Officer 3/4 side body with 42" wide forward and 50" wide rearward enhanced extended compartmentation. Includes (1) 56" wide compartment over the wheel well.
Officer 3/4 side body with 48" wide forward and 62" wide rearward enhanced extended compartmentation. Includes (1) 56" wide compartment over the wheel well.
Officer side body with full height 24" wide forward and 36" wide rearward compartmentation. Includes (1) 33" wide compartment (forward) over the wheel well and (1) Zico Overhead Ladder Rack.
Officer side body with full height 30" wide forward and 36" wide rearward compartmentation. Includes (1) 33" wide compartment (forward) over the wheel well and (1) Zico Overhead Ladder Rack.
Officer side body with full height 36" wide forward and 36" wide rearward compartmentation. Includes (1) 33" wide compartment (forward) over the wheel well and (1) Zico Overhead Ladder Rack.
Officer side body with full height 42" wide forward and 42" wide rearward compartmentation. Includes (1) 33" wide compartment (forward) over the wheel well and (1) Zico Overhead Ladder Rack.
PRICE
$6,011.00
$6,428.00
$6,879.00
$7,361.00
$6,245.00
$6,637.00
$7,059.00
$7,508.00
$7,990.00
$6,533.00
$6,924.00
$7,344.00
$7,796.00
$8,278.00
$15,539.00
$16,167.00
$16,838.00
$17,559.00
Option No.
3120‐0040
3120‐0041
3120‐0042
3120‐0043
3120‐0044
3120‐0045
3120‐0046
3120‐0047
3120‐0048
3120‐0049
3120‐0050
3120‐0051
3120‐0052
3120‐0053
3120‐0054
3120‐0055
3120‐0056
3120‐0057
Description
Officer side body with full height 48" wide forward and 48" wide rearward compartmentation. Includes (1) 33" wide compartment (forward) over the wheel well and (1) Zico Overhead Ladder Rack.
Officer side body with full height 24" wide forward and 50" wide rearward extended compartmentation. Includes (1) 33" wide compartment (forward) over the wheel well and (1) Zico Overhead Ladder Rack.
Officer side body with full height 30" wide forward and 50" wide rearward extended compartmentation. Includes (1) 33" wide compartment (forward) over the wheel well and (1) Zico Overhead Ladder Rack.
Officer side body with full height 36" wide forward and 50" wide rearward extended compartmentation. Includes (1) 33" wide compartment (forward) over the wheel well and (1) Zico Overhead Ladder Rack.
Officer side body with full height 42" wide forward and 56" wide rearward extended compartmentation. Includes (1) 33" wide compartment (forward) over the wheel well and (1) Zico Overhead Ladder Rack.
Officer side body with full height 48" wide forward and 62" wide rearward extended compartmentation. Includes (1) 33" wide compartment (forward) over the wheel well and (1) Zico Overhead Ladder Rack.
Officer side body with full height 24" wide forward and 50" wide rearward enhanced extended compartmentation. Includes (1) 33" wide compartment (forward) over the wheel well and (1) Zico Overhead Ladder Rack.
Officer side body with full height 30" wide forward and 50" wide rearward enhanced extended compartmentation. Includes (1) 33" wide compartment (forward) over the wheel well and (1) Zico Overhead Ladder Rack.
Officer side body with full height 36" wide forward and 50" wide rearward enhanced extended compartmentation. Includes (1) 33" wide compartment (forward) over the wheel well and (1) Zico Overhead Ladder Rack.
Officer side body with full height 42" wide forward and 56" wide rearward enhanced extended compartmentation. Includes (1) 33" wide compartment (forward) over the wheel well and (1) Zico Overhead Ladder Rack.
Officer side body with full height 48" wide forward and 62" wide rearward enhanced extended compartmentation. Includes (1) 33" wide compartment (forward) over the wheel well and (1) Zico Overhead Ladder Rack.
Officer half side body with 36" wide forward and 36" wide rearward compartmentation. Includes adjustable ladder tracks and 30 degree rear body angle for greater angle of departure.
Officer 3/4 side body with full height 24" wide forward and 36" wide rearward compartmentation. Includes (1) 56" wide compartment over the wheel well and 30 degree rear body angle for greater angle of departure.
Officer 3/4 side body with full height 30" wide forward and 36" wide rearward compartmentation. Includes (1) 56" wide compartment over the wheel well and 30 degree rear body angle for greater angle of departure.
Officer 3/4 side body with full height 36" wide forward and 36" wide rearward compartmentation. Includes (1) 56" wide compartment over the wheel well and 30 degree rear body angle for greater angle of departure.
Officer side body with full height 24" wide forward and 36" wide rearward compartmentation. Includes (1) 33" wide compartment (forward) over the wheel well, (1) Zico Overhead Ladder Rack and 30 degree rear body angle for greater angle of departure.
Officer side body with full height 30" wide forward and 36" wide rearward compartmentation. Includes (1) 33" wide compartment (forward) over the wheel well, (1) Zico Overhead Ladder Rack and 30 degree rear body angle for greater angle of departure.
Officer side body with full height 36" wide forward and 36" wide rearward compartmentation. Includes (1) 33" wide compartment (forward) over the wheel well, (1) Zico Overhead Ladder Rack and 30 degree rear body angle for greater angle of departure.
PRICE
$18,327.00
$16,167.00
$16,796.00
$17,468.00
$18,188.00
$18,957.00
$16,457.00
$17,083.00
$17,754.00
$18,475.00
$19,244.00
$5,157.00
$9,661.00
$9,967.00
$10,273.00
$17,550.00
$17,856.00
$18,162.00
Option No.
3120‐0058
3120‐0059
3120‐0060
3120‐0061
3120‐0062
3120‐0063
3120‐0064
3120‐0065
3120‐0066
3120‐0067
3120‐0068
3120‐0069
3120‐0070
3120‐0080
3120‐0081
3120‐0082
3120‐0083
3120‐0084
Description
Stainless steel officer half side body with 48" wide forward and 48" wide rearward compartmentation (interior). Includes adjustable ladder tracks.
Stainless steel officer half side body with 48" wide forward and 60" wide rearward compartmentation (interior). Includes adjustable ladder tracks.
Stainless steel officer half side body with 60" wide forward and 60" wide rearward compartmentation (interior). Includes adjustable ladder tracks.
Stainless steel officer 3/4 side body with full height 36" wide forward and 48" wide rearward compartmentation (interior). Includes (1) 60" wide compartment over the wheel well.
Stainless steel officer 3/4 side body with full height 48" wide forward and 48" wide rearward compartmentation (interior). Includes (1) 60" wide compartment over the wheel well.
Stainless steel officer 3/4 side body with full height 48" wide forward and 60" wide rearward compartmentation (interior). Includes (1) 60" wide compartment over the wheel well.
Stainless steel officer 3/4 side body with full height 60" wide forward and 60" wide rearward compartmentation (interior). Includes (1) 60" wide compartment over the wheel well.
Stainless steel officer side body with full height 36" wide forward and 48" wide rearward compartmentation (interior). Includes (1) 45" wide compartment (rearward) over the wheel well and (1) Zico Overhead Ladder Rack.
Stainless steel officer side body with full height 48" wide forward and 48" wide rearward compartmentation (interior). Includes (1) 45" wide compartment (rearward) over the wheel well and (1) Zico Overhead Ladder Rack.
Stainless steel officer side body with full height 48" wide forward and 60" wide rearward compartmentation (interior). Includes (1) 45" wide compartment (rearward) over the wheel well and (1) Zico Overhead Ladder Rack.
Stainless steel officer side body with full height 60" wide forward and 60" wide rearward compartmentation (interior). Includes (1) 45" wide compartment (rearward) over the wheel well and (1) Zico Overhead Ladder Rack.
Stainless steel officer side body with full height 48" wide forward and 60" wide rearward compartmentation (interior). Includes (1) 60" wide compartment over the wheel well. For use with in the hosebed area ladder storage.
Stainless steel officer side body with full height 60" wide forward and 60" wide rearward compartmentation (interior). Includes (1) 60" wide compartment over the wheel well. For use with in the hosebed area or thru the tank ladder storage.
Officer side body with full height 36" wide forward and 36" wide rearward compartmentation. Includes (1) 33" wide compartment (forward) over the wheel well and (1) Zico Overhead Ladder Rack.
Officer side body with full height 42" wide forward and 42" wide rearward compartmentation. Includes (1) 33" wide compartment (forward) over the wheel well and (1) Zico Overhead Ladder Rack.
Officer side body with full height 48" wide forward and 48" wide rearward compartmentation. Includes (1) 33" wide compartment (forward) over the wheel well and (1) Zico Overhead Ladder Rack.
Officer side body with full height 36" wide forward and 36" wide rearward compartmentation. Includes (1) 56" wide compartment over the wheel well and one (1)ladder storage tunnel and access door at rear.
Officer side body with full height 42" wide forward and 42" wide rearward compartmentation. Includes (1) 56" wide compartment over the wheel well and one (1)ladder storage tunnel and access door at rear.
PRICE
$6,477.00
$6,802.00
$6,931.00
$7,074.00
$8,095.00
$8,502.00
$8,662.00
$18,524.00
$20,160.00
$23,022.00
$21,066.00
$13,599.00
$13,859.00
$18,017.00
$18,788.00
$19,613.00
$13,922.00
$14,691.00
Option No.
3120‐0085
3120‐0086
3120‐0087
3120‐0088
3120‐0089
3120‐0090
3120‐0091
3120‐0092
3120‐0093
3120‐0094
3120‐0095
3120‐0096
3120‐0097
3120‐0098
3120‐0099
3120‐0100
3120‐0101
3120‐0102
3120‐0104
Description
Officer side body with full height 48" wide forward and 48" wide rearward compartmentation. Includes (1) 56" wide compartment over the wheel well and one (1)ladder storage tunnel and access door at rear.
Officer side body with full height 42" wide forward and 42" wide rearward compartmentation. Includes (1) 56" wide compartment over the wheel well.
Officer side body with full height 48" wide forward and 48" wide rearward compartmentation. Includes (1) 56" wide compartment over the wheel well. For use with thru the tank ladder.
Officer side body with full height 60" wide forward and 42" wide rearward compartmentation. Includes (1) 33" wide compartment (forward) over the wheel well and (1) Zico Overhead Ladder Rack.
Officer side body with full height 60" wide forward and 42" wide rearward compartmentation. Includes (1) 56" wide compartment over the wheel well and one (1)ladder storage tunnel and access door at rear.
Officer side body with full height 60" wide forward and 42" wide rearward compartmentation. Includes (1) 56" wide compartment over the wheel well. For use with thru the tank ladder storage.
Officer half side body with 36" wide rearward compartmentation. Includes adjustable ladder tracks and 30 degree rear body angle for greater angle of departure.
Officer 3/4 side body with full height 36" wide rearward compartmentation. Includes (1) 56" wide compartment over the wheel well and 30 degree rear body angle for greater angle of departure.
Officer half side body with 36" wide rearward compartmentation. Includes adjustable ladder tracks.
Officer 3/4 side body with full height 36" wide rearward compartmentation. Includes (1) 56" wide compartment over the wheel well.
Officer full height side body with upper and lower compartmentation. Includes 42" wide forward and 42" wide rearward lower compartments and (3) opening upper compartments. For use with ladder storage thru tank.
Officer side body with full height 42" wide forward and 42" wide rearward compartmentation. Includes (1) 56" wide compartment over the wheel well. For use with ladder storage thru tank.
Officer full height side body with upper and lower compartmentation. Includes 48" wide forward and 48" wide rearward lower compartments and (3) opening upper compartments. For use with ladder storage thru tank.
Officer side body with full height 48" wide forward and 48" wide rearward compartmentation. Includes (1) 56" wide compartment over the wheel well. For use with ladder storage thru tank.
Officer side body with full height 42" wide forward and 56" wide rearward extended compartmentation. Includes (1) 56" wide compartment over the wheel well.
Officer side body with full height 42" wide forward and 56" wide rearward enhanced extended compartmentation. Includes (1) 56" wide compartment over the wheel well.
Officer side body with full height 48" wide forward and 62" wide rearward extended compartmentation. Includes (1) 56" wide compartment over the wheel well.
Officer side body with full height 48" wide forward and 62" wide rearward enhanced extended compartmentation. Includes (1) 56" wide compartment over the wheel well.
Stainless steel officer 3/4 side body with full height 36" wide forward and 48" wide rearward compartmentation (interior). Includes (1) 60" wide compartment over the wheel well.
PRICE
$15,515.00
$11,773.00
$12,597.00
$20,494.00
$16,399.00
$13,480.00
$2,592.00
$8,716.00
$2,774.00
$5,118.00
$11,454.00
$11,005.00
$12,224.00
$11,773.00
$11,633.00
$11,922.00
$12,403.00
$12,690.00
$12,995.00
Option No.
3120‐0105
3120‐0106
3120‐0107
3120‐0108
3120‐0109
3120‐0110
3120‐0111
3120‐0112
3120‐0113
3120‐0114
3120‐0115
3120‐0116
3120‐0117
3120‐0118
3120‐0119
3120‐0121
3120‐0123
3120‐0124
3120‐0125
Description
Stainless steel officer 3/4 side body with full height 48" wide forward and 48" wide rearward compartmentation (interior). Includes (1) 60" wide compartment over the wheel well.
Stainless steel officer 3/4 side body with full height 60" wide forward and 60" wide rearward compartmentation (interior). Includes (1) 60" wide compartment over the wheel well.
Stainless steel officer 3/4 side body with full height 48" wide forward and 60" wide rearward compartmentation (interior). Includes (1) 60" wide compartment over the wheel well.
Stainless steel officer side body with full height 36" wide forward and 48" wide (interior) rearward compartmentation. Includes (1) 45" wide (interior) compartment (forward) over the wheel well and (1) Zico Overhead Ladder Rack.
Stainless steel officer side body with full height 48" wide forward and 48" wide (interior) rearward compartmentation. Includes (1) 45" wide (interior) compartment (forward) over the wheel well and (1) Zico Overhead Ladder Rack.
Stainless steel officer side body with full height 60" wide forward and 60" wide (interior) rearward compartmentation. Includes (1) 45" wide (interior) compartment (forward) over the wheel well and (1) Zico Overhead Ladder Rack.
Stainless steel officer side body with full height 48" wide forward and 60" wide (interior) rearward compartmentation. Includes (1) 45" wide (interior) compartment (forward) over the wheel well and (1) Zico Overhead Ladder Rack.
Stainless steel officer side body with full height 36" wide forward and 48" wide rearward (interior) compartmentation. Includes (1) 60" wide compartment over the wheel well. For use with in the hosebed ladder storage.
Stainless steel officer side body with full height 48" wide forward and 48" wide rearward (interior) compartmentation. Includes (1) 60" wide compartment over the wheel well. For use with in the hosebed ladder storage.
Stainless steel officer side body with full height 48" wide forward and 60" wide rearward (interior) compartmentation. Includes (1) 60" wide compartment over the wheel well. For use with in the hosebed ladder storage.
Stainless steel officer side body with full height 60" wide forward and 60" wide rearward (interior) compartmentation. Includes (1) 60" wide compartment over the wheel well. For use with in the hosebed ladder storage.
Stainless steel officer side body with full height 36" wide forward and 48" wide (interior) rearward compartmentation. Includes (1) 60" wide compartment over the wheel well and one (1) ladder storage tunnel and access door at rear with push‐button latch.
Stainless steel officer side body with full height 48" wide forward and 48" wide (interior) rearward compartmentation. Includes (1) 60" wide compartment over the wheel well and one (1) ladder storage tunnel and access door at rear with push‐button latch.
Stainless steel officer side body with full height 48" wide forward and 60" wide (interior) rearward compartmentation. Includes (1) 60" wide compartment over the wheel well and one (1) ladder storage tunnel and access door at rear with push‐button latch.
Stainless steel officer side body with full height 60" wide forward and 60" wide (interior) rearward compartmentation. Includes (1) 60" wide compartment over the wheel well and one (1) ladder storage tunnel and access door at rear with push‐button latch.
Officer side body with full height 36" wide forward and 36" wide rearward compartmentation. Includes (1) 56" wide compartment over the wheel well.
Officer half side body with 60" wide forward and 42" wide rearward compartmentation. Includes adjustable ladder tracks.
Officer 3/4 side body with full height 60" wide forward and 42" wide rearward compartmentation. Includes (1) 56" wide compartment over the wheel well.
Officer 3/4 side body with upper and lower compartmentation. Includes 60" wide forward and 42" wide rearward lower compartments and (3) opening upper compartments.
PRICE
$13,651.00
$14,963.00
$14,305.00
$19,817.00
$21,572.00
$22,542.00
$22,219.00
$12,103.00
$13,859.00
$14,274.00
$13,859.00
$15,724.00
$17,477.00
$18,352.00
$18,446.00
$10,949.00
$6,302.00
$7,876.00
$8,355.00
Option No.
3120‐0126
3120‐0127
3120‐0128
3120‐0131
3120‐0132
3120‐0134
3120‐0135
3120‐0136
3120‐0137
3120‐0138
3120‐0139
3120‐0140
3120‐0141
3120‐0142
3120‐0143
3120‐0144
3120‐0145
3120‐0146
Description
Officer side body with full height 60" wide forward and 42" wide rearward compartmentation. Includes (1) 56" wide compartment over the wheel well. For use with ladder storage thru tank.
Officer full height side body with upper and lower compartmentation. Includes 60" wide forward and 42" wide rearward lower compartments and (3) opening upper compartments. For use with ladder storage thru tank.
Officer side body with full height 60" wide forward and 42" wide rearward compartmentation. Includes (1) 33" wide compartment (forward) over the wheel well and (1) Zico Overhead Ladder Rack.
Stainless steel officer side body with full height 24" wide forward and 48" wide (interior) rearward compartmentation. Includes (1) 60" wide compartment over the wheel well and one (1) ladder storage tunnel and access door at rear with push‐button latch.
Officer side body with full height 30" wide forward and 50" wide rearward extended compartmentation. Includes (1) 56" wide compartment over the wheel well and (1) 2‐Arm Ladder Rack. The ladder rack is to be painted job color and includes amber lights on each end to visually indicate when the rack is in motion.
Officer side body with full height 30" wide forward and 36" wide rearward compartmentation. Includes (1) 56" wide compartment over the wheel well. For use with over the hosebed storage rack.
Officer side body with full height 36" wide forward and 36" wide rearward compartmentation. Includes (1) 56" wide compartment over the wheel well. For use with over the hosebed storage rack.
Officer side body with full height 60" wide forward and 56" wide rearward compartmentation. Includes (1) 56" wide compartment over the wheel well.
Officer 3/4 side body with full height 50" wide enhanced extended rearward compartmentation. Includes (1) 56" wide compartment over the wheel well.
Officer 3/4 side body with upper and lower compartmentation. Includes 24" wide forward and 36" wide rearward lower compartments and (3) opening upper compartments.
Officer 3/4 side body with full height 24" wide forward and 36" wide rearward compartmentation. Includes (1) 56" wide compartment over the wheel well.
Officer 3/4 side body with upper and lower compartmentation. Includes 30" wide forward and 36" wide rearward lower compartments and (3) opening upper compartments.
Officer 3/4 side body with upper and lower compartmentation. Includes 36" wide forward and 36" wide rearward lower compartments and (3) opening upper compartments.
Officer 3/4 side body with upper and lower compartmentation. Includes 42" wide forward and 42" wide rearward lower compartments and (3) opening upper compartments.
Officer 3/4 side body with upper and lower compartmentation. Includes 48" wide forward and 48" wide rearward lower compartments and (3) opening upper compartments.
Officer 3/4 side body with full height 30" wide forward and 36" wide rearward compartmentation. Includes (1) 56" wide compartment over the wheel well.
Officer 3/4 side body with full height 36" wide forward and 36" wide rearward compartmentation. Includes (1) 56" wide compartment over the wheel well.
Officer 3/4 side body with full height 42" wide forward and 42" wide rearward compartmentation. Includes (1) 56" wide compartment over the wheel well.
PRICE
$12,597.00
$13,078.00
$18,788.00
$13,969.00
$29,909.00
$9,612.00
$10,297.00
$13,480.00
$6,033.00
$6,065.00
$5,617.00
$6,458.00
$6,878.00
$7,328.00
$7,810.00
$6,011.00
$6,428.00
$6,879.00
Option No.
3120‐0147
3120‐0148
3120‐0149
3120‐0150
3120‐0151
3120‐0152
3120‐0153
3120‐0154
3120‐0155
3120‐0156
3120‐0157
3120‐0158
3120‐0159
3120‐0160
3120‐0161
3120‐0162
3120‐0163
3120‐0164
Description
Officer 3/4 side body with full height 48" wide forward and 48" wide rearward compartmentation. Includes (1) 56" wide compartment over the wheel well.
Officer 3/4 side body with 24" wide forward and 50" wide rearward extended compartmentation. Includes (1) 56" wide compartment over the wheel well.
Officer 3/4 side body with 30" wide forward and 50" wide rearward extended compartmentation. Includes (1) 56" wide compartment over the wheel well.
Officer 3/4 side body with 36" wide forward and 50" wide rearward extended compartmentation. Includes (1) 56" wide compartment over the wheel well.
Officer 3/4 side body with 42" wide forward and 56" wide rearward extended compartmentation. Includes (1) 56" wide compartment over the wheel well.
Officer 3/4 side body with 48" wide forward and 62" wide rearward extended compartmentation. Includes (1) 56" wide compartment over the wheel well.
Officer 3/4 side body with 24" wide forward and 50" wide rearward enhanced extended compartmentation. Includes (1) 56" wide compartment over the wheel well.
Officer 3/4 side body with 30" wide forward and 50" wide rearward enhanced extended compartmentation. Includes (1) 56" wide compartment over the wheel well.
Officer 3/4 side body with 36" wide forward and 50" wide rearward enhanced extended compartmentation. Includes (1) 56" wide compartment over the wheel well.
Officer 3/4 side body with 42" wide forward and 56" wide rearward enhanced extended compartmentation. Includes (1) 56" wide compartment over the wheel well.
Officer 3/4 side body with 48" wide forward and 62" wide rearward enhanced extended compartmentation. Includes (1) 56" wide compartment over the wheel well.
Officer side body with full height 24" wide forward and 36" wide rearward compartmentation. Includes (1) 33" wide compartment over the wheel well and (1) Zico Overhead Ladder Rack.
Officer side body with full height 30" wide forward and 36" wide rearward compartmentation. Includes (1) 33" wide compartment over the wheel well and (1) Zico Overhead Ladder Rack.
Officer side body with full height 36" wide forward and 36" wide rearward compartmentation. Includes (1) 33" wide compartment over the wheel well and (1) Zico Overhead Ladder Rack.
Officer side body with full height 42" wide forward and 42" wide rearward compartmentation. Includes (1) 33" wide compartment over the wheel well and (1) Zico Overhead Ladder Rack.
Officer side body with full height 48" wide forward and 48" wide rearward compartmentation. Includes (1) 33" wide compartment over the wheel well and (1) Zico Overhead Ladder Rack.
Officer side body with full height 24" wide forward and 50" wide rearward extended compartmentation. Includes (1) 33" wide compartment over the wheel well and (1) Zico Overhead Ladder Rack.
Officer side body with full height 30" wide forward and 50" wide rearward extended compartmentation. Includes (1) 33" wide compartment over the wheel well and (1) Zico Overhead Ladder Rack.
PRICE
$7,361.00
$6,245.00
$6,637.00
$7,059.00
$7,508.00
$7,990.00
$6,533.00
$6,924.00
$7,344.00
$7,796.00
$8,278.00
$15,539.00
$16,167.00
$16,838.00
$17,559.00
$18,327.00
$16,167.00
$16,796.00
Option No.
3120‐0165
3120‐0166
3120‐0167
3120‐0168
3120‐0169
3120‐0170
3120‐0171
3120‐0172
3120‐0173
3120‐0174
3120‐0175
3120‐0176
3120‐0177
3120‐0178
3120‐0179
3120‐0180
3120‐0181
3120‐0182
Description
Officer side body with full height 36" wide forward and 50" wide rearward extended compartmentation. Includes (1) 33" wide compartment over the wheel well and (1) Zico Overhead Ladder Rack.
Officer side body with full height 42" wide forward and 56" wide rearward extended compartmentation. Includes (1) 33" wide compartment over the wheel well and (1) Zico Overhead Ladder Rack.
Officer side body with full height 48" wide forward and 62" wide rearward extended compartmentation. Includes (1) 33" wide compartment over the wheel well and (1) Zico Overhead Ladder Rack.
Officer side body with full height 24" wide forward and 50" wide rearward enhanced extended compartmentation. Includes (1) 33" wide compartment over the wheel well and (1) Zico Overhead Ladder Rack.
Officer side body with full height 30" wide forward and 50" wide rearward enhanced extended compartmentation. Includes (1) 33" wide compartment over the wheel well and (1) Zico Overhead Ladder Rack.
Officer side body with full height 36" wide forward and 50" wide rearward enhanced extended compartmentation. Includes (1) 33" wide compartment over the wheel well and (1) Zico Overhead Ladder Rack.
Officer side body with full height 42" wide forward and 56" wide rearward enhanced extended compartmentation. Includes (1) 33" wide compartment over the wheel well and (1) Zico Overhead Ladder Rack.
Officer side body with full height 48" wide forward and 62" wide rearward enhanced extended compartmentation. Includes (1) 33" wide compartment over the wheel well and (1) Zico Overhead Ladder Rack.
Officer 3/4 side body with full height 24" wide forward and 36" wide rearward compartmentation. Includes (1) 56" wide compartment over the wheel well and 30 degree rear body angle for greater angle of departure.
Officer 3/4 side body with full height 30" wide forward and 36" wide rearward compartmentation. Includes (1) 56" wide compartment over the wheel well and 30 degree rear body angle for greater angle of departure.
Officer 3/4 side body with full height 36" wide forward and 36" wide rearward compartmentation. Includes (1) 56" wide compartment over the wheel well and 30 degree rear body angle for greater angle of departure.
Officer side body with full height 24" wide forward and 36" wide rearward compartmentation. Includes (1) 33" wide compartment over the wheel well and (1) Zico Overhead Ladder Rack. Rear bottom corner of truck will be angled 30 degrees for a greater rear angle of departure.
Officer side body with full height 30" wide forward and 36" wide rearward compartmentation. Includes (1) 33" wide compartment over the wheel well, (1) Zico Overhead Ladder Rack and 30 degree rear body angle for greater angle of departure.
Officer side body with full height 36" wide forward and 36" wide rearward compartmentation. Includes (1) 33" wide compartment over the wheel well, (1) Zico Overhead Ladder Rack and 30 degree rear body angle for greater angle of departure.
Stainless steel officer 3/4 side body with full height 36" wide forward and 48" wide rearward compartmentation (interior). Includes (1) 60" wide compartment over the wheel well.
Stainless steel officer 3/4 side body with full height 48" wide forward and 48" wide rearward compartmentation (interior). Includes (1) 60" wide compartment over the wheel well.
Stainless steel officer 3/4 side body with full height 48" wide forward and 60" wide rearward compartmentation (interior). Includes (1) 60" wide compartment over the wheel well.
Stainless steel officer 3/4 side body with full height 60" wide forward and 60" wide rearward compartmentation (interior). Includes (1) 60" wide compartment over the wheel well.
PRICE
$17,468.00
$18,188.00
$18,957.00
$16,457.00
$17,083.00
$17,754.00
$18,475.00
$19,244.00
$9,661.00
$9,967.00
$10,273.00
$17,550.00
$17,856.00
$18,162.00
$7,074.00
$8,095.00
$8,502.00
$8,662.00
Option No.
3120‐0183
3120‐0184
3120‐0185
3120‐0186
3120‐0187
3120‐0188
3120‐0189
3120‐0190
3120‐0191
3120‐0192
3120‐0193
3120‐0194
3120‐0195
3120‐0196
3120‐0197
3120‐0198
3120‐0199
3120‐0200
Description
Stainless steel officer side body with full height 36" wide forward and 48" wide rearward compartmentation (interior). Includes (1) 45" wide compartment over the wheel well and (1) Zico Overhead Ladder Rack.
Stainless steel officer side body with full height 48" wide forward and 48" wide rearward compartmentation (interior). Includes (1) 45" wide compartment over the wheel well and (1) Zico Overhead Ladder Rack.
Stainless steel officer side body with full height 48" wide forward and 60" wide rearward compartmentation (interior). Includes (1) 45" wide compartment over the wheel well and (1) Zico Overhead Ladder Rack.
Stainless steel officer side body with full height 60" wide forward and 60" wide rearward compartmentation (interior). Includes (1) 45" wide compartment over the wheel well and (1) Zico Overhead Ladder Rack.
Stainless steel officer side body with full height 48" wide forward and 60" wide rearward compartmentation (interior). Includes (1) 60" wide compartment over the wheel well. For use with in the hosebed area ladder storage.
Stainless steel officer side body with full height 60" wide forward and 60" wide rearward compartmentation (interior). Includes (1) 60" wide compartment over the wheel well. For use with in the hosebed area or thru the tank ladder storage.
Officer side body with full height 36" wide forward and 36" wide rearward compartmentation. Includes (1) 33" wide compartment over the wheel well and (1) Zico Overhead Ladder Rack.
Officer side body with full height 42" wide forward and 42" wide rearward compartmentation. Includes (1) 33" wide compartment over the wheel well and (1) Zico Overhead Ladder Rack.
Officer side body with full height 48" wide forward and 48" wide rearward compartmentation. Includes (1) 33" wide compartment over the wheel well and (1) Zico Overhead Ladder Rack.
Officer side body with full height 36" wide forward and 36" wide rearward compartmentation. Includes (1) 56" wide compartment over the wheel well and one (1) storage tunnel.
Officer side body with full height 42" wide forward and 42" wide rearward compartmentation. Includes (1) 56" wide compartment over the wheel well and one (1) storage tunnel.
Officer side body with full height 48" wide forward and 48" wide rearward compartmentation. Includes (1) 56" wide compartment over the wheel well and one (1) storage tunnel.
Officer side body with full height 42" wide forward and 42" wide rearward compartmentation. Includes (1) 56" wide compartment over the wheel well.
Officer side body with full height 48" wide forward and 48" wide rearward compartmentation. Includes (1) 56" wide compartment over the wheel well.
Officer side body with full height 60" wide forward and 42" wide rearward compartmentation. Includes (1) 33" wide compartment over the wheel well and (1) Zico Overhead Ladder Rack.
Officer side body with full height 60" wide forward and 42" wide rearward compartmentation. Includes (1) 56" wide compartment over the wheel well and one (1) storage tunnel.
Officer side body with full height 60" wide forward and 42" wide rearward compartmentation. Includes (1) 56" wide compartment over the wheel well.
Officer 3/4 side body with full height 36" wide rearward compartmentation. Includes (1) 56" wide compartment over the wheel well and 30 degree rear body angle for greater angle of departure.
PRICE
$18,524.00
$20,160.00
$23,022.00
$21,066.00
$13,599.00
$13,859.00
$18,017.00
$18,788.00
$19,613.00
$13,922.00
$14,691.00
$15,515.00
$11,773.00
$12,597.00
$20,494.00
$16,399.00
$13,480.00
$8,716.00
Option No.
Description
PRICE
3120‐0201
Officer 3/4 side body with full height 36" wide rearward compartmentation. Includes (1) 56" wide compartment over the wheel well.
Officer full height side body with upper and lower compartmentation. Includes 42" wide forward and 42" wide rearward lower compartments and (3) opening upper compartments. For use with ladder storage thru tank.
Officer side body with full height 42" wide forward and 42" wide rearward compartmentation. Includes (1) 56" wide compartment over the wheel well.
Officer full height side body with upper and lower compartmentation. Includes 48" wide forward and 48" wide rearward lower compartments and (3) opening upper compartments. For use with ladder storage thru tank.
Officer side body with full height 48" wide forward and 48" wide rearward compartmentation. Includes (1) 56" wide compartment over the wheel well.
Officer side body with full height 42" wide forward and 56" wide rearward extended compartmentation. Includes (1) 56" wide compartment over the wheel well.
Officer side body with full height 42" wide forward and 56" wide rearward enhanced extended compartmentation. Includes (1) 56" wide compartment over the wheel well.
Officer side body with full height 48" wide forward and 62" wide rearward extended compartmentation. Includes (1) 56" wide compartment over the wheel well.
Officer side body with full height 48" wide forward and 62" wide rearward enhanced extended compartmentation. Includes (1) 56" wide compartment over the wheel well.
Stainless steel officer 3/4 side body with full height 36" wide forward and 48" wide rearward compartmentation (interior). Includes (1) 60" wide compartment over the wheel well.
Stainless steel officer 3/4 side body with full height 48" wide forward and 48" wide rearward compartmentation (interior). Includes (1) 60" wide compartment over the wheel well.
Stainless steel officer 3/4 side body with full height 60" wide forward and 60" wide rearward compartmentation (interior). Includes (1) 60" wide compartment over the wheel well.
Stainless steel officer 3/4 side body with full height 48" wide forward and 60" wide rearward compartmentation (interior). Includes (1) 60" wide compartment over the wheel well.
Stainless steel officer side body with full height 36" wide forward and 48" wide (interior) rearward compartmentation. Includes (1) 45" wide (interior) compartment over the wheel well and (1) Zico Overhead Ladder Rack.
Stainless steel officer side body with full height 48" wide forward and 48" wide (interior) rearward compartmentation. Includes (1) 45" wide (interior) compartment over the wheel well and (1) Zico Overhead Ladder Rack.
Stainless steel officer side body with full height 60" wide forward and 60" wide (interior) rearward compartmentation. Includes (1) 45" wide (interior) compartment over the wheel well and (1) Zico Overhead Ladder Rack.
Stainless steel officer side body with full height 48" wide forward and 60" wide (interior) rearward compartmentation. Includes (1) 45" wide (interior) compartment over the wheel well and (1) Zico Overhead Ladder Rack.
Stainless steel officer side body with full height 36" wide forward and 48" wide rearward (interior) compartmentation. Includes (1) 60" wide compartment over the wheel well. For use with in the hosebed ladder storage.
$5,118.00
3120‐0202
3120‐0203
3120‐0204
3120‐0205
3120‐0206
3120‐0207
3120‐0208
3120‐0209
3120‐0210
3120‐0211
3120‐0212
3120‐0213
3120‐0214
3120‐0215
3120‐0216
3120‐0217
3120‐0218
$11,454.00
$11,005.00
$12,224.00
$11,773.00
$11,633.00
$11,922.00
$12,403.00
$12,690.00
$12,995.00
$13,651.00
$14,963.00
$14,305.00
$19,817.00
$21,572.00
$22,542.00
$22,219.00
$12,103.00
Option No.
3120‐0219
3120‐0220
3120‐0221
3120‐0222
3120‐0223
3120‐0224
3120‐0225
3120‐0226
3120‐0227
3120‐0228
3120‐0229
3120‐0230
3120‐0231
3120‐0232
3120‐0233
3120‐0234
3120‐0235
3120‐0236
3120‐0237
Description
Stainless steel officer side body with full height 48" wide forward and 48" wide rearward (interior) compartmentation. Includes (1) 60" wide compartment over the wheel well. For use with in the hosebed ladder storage.
Stainless steel officer side body with full height 48" wide forward and 60" wide rearward (interior) compartmentation. Includes (1) 60" wide compartment over the wheel well. For use with in the hosebed ladder storage.
Stainless steel officer side body with full height 60" wide forward and 60" wide rearward (interior) compartmentation. Includes (1) 60" wide compartment over the wheel well. For use with in the hosebed ladder storage.
Stainless steel officer side body with full height 36" wide forward and 48" wide (interior) rearward compartmentation. Includes (1) 60" wide compartment over the wheel well and one (1) ladder storage tunnel and access door at rear with push‐button latch.
Stainless steel officer side body with full height 48" wide forward and 48" wide (interior) rearward compartmentation. Includes (1) 60" wide compartment over the wheel well and one (1) ladder storage tunnel and access door at rear with push‐button latch.
Stainless Steel Officer side body with full height 48" wide forward and 60" wide (interior) rearward compartmentation. Includes (1) 60" wide compartment over the wheel well and one (1) ladder storage tunnel and access door at rear with push‐button latch.
Stainless steel officer side body with full height 60" wide forward and 60" wide (interior) rearward compartmentation. Includes (1) 60" wide compartment over the wheel well and one (1) ladder storage tunnel and access door at rear with push‐button latch.
Officer side body with full height 36" wide forward and 36" wide rearward compartmentation. Includes (1) 56" wide compartment over the wheel well.
Officer 3/4 side body with full height 60" wide forward and 42" wide rearward compartmentation. Includes (1) 56" wide compartment over the wheel well.
Officer 3/4 side body with upper and lower compartmentation. Includes 60" wide forward and 42" wide rearward lower compartments and (3) opening upper compartments.
Officer side body with full height 60" wide forward and 42" wide rearward compartmentation. Includes (1) 56" wide compartment over the wheel well.
Officer full height side body with upper and lower compartmentation. Includes 60" wide forward and 42" wide rearward lower compartments and (3) opening upper compartments. For use with ladder storage thru tank.
Officer side body with full height 60" wide forward and 42" wide rearward compartmentation. Includes (1) 33" wide compartment over the wheel well and (1) Zico Overhead Ladder Rack.
Officer side body with full height 36" wide forward and 36" wide rearward compartmentation. Includes (1) 56" wide compartment over the wheel well.
Officer side body with full height 60" wide forward and 56" wide rearward compartmentation. Includes (1) 56" wide compartment over the wheel well and one (1)ladder storage tunnel and access door at rear.
Officer side body with full height 48" wide forward and 48" wide rearward compartmentation. Includes (1) 56" wide compartment over the wheel well.
Officer full height side body with full height 36" wide rearward compartmentation. Includes (1) 33" wide compartment over the wheel well and an overhead Zico ladder rack..
Overhead Ladder Rack to be offset forward includes shifting compartment (rearward) over the wheel well.
Overhead Ladder Rack to be offset rearward includes shifting compartment (forward) over the wheel well.
PRICE
$13,859.00
$14,274.00
$13,859.00
$15,724.00
$17,477.00
$18,352.00
$18,446.00
$10,949.00
$7,876.00
$8,355.00
$12,597.00
$13,078.00
$18,788.00
$10,297.00
$16,399.00
$12,597.00
$10,977.00
$609.00
$0.00
Option No.
3120‐0238
3120‐0239
3120‐0240
3120‐0241
3120‐0242
3120‐0243
3120‐0244
3120‐0245
3120‐0246
3120‐0247
3120‐0248
3120‐0249
3120‐0250
3120‐0251
3120‐0252
3120‐0254
3120‐0255
3120‐0256
Description
Officer full height side body with upper and lower compartmentation. Includes 36" wide forward and 36" wide rearward lower compartments and (2) opening upper compartments. Includes (1) Zico Overhead Ladder Rack mounted centered between upper compartments.
Officer side compartment top storage box (PR). Locate one forward and one rearward of the ladder rack. Boxes to be smooth plate and painted job color with diamond plate tops. The rearward box to have a rear vertically hinged door with push‐button latch. Boxes to have (1) diamond plate lid each with push button latch.
Officer 3/4 side body with upper and lower compartmentation. Includes 24" wide forward and 36" wide rearward lower compartments and (2) opening upper compartments.
Compartment R1 to have rescue style interior compartment height.
Officer side tunnel to hold: (1) 1500 gallon Fol‐da‐tank.
Officer 3/4 side body with full height 42" wide forward and 48" wide rearward compartmentation. Includes (1) 56" wide compartment over the wheel well.
Officer side body with full height 30" wide forward and 50" wide rearward extended compartmentation. Includes (1) 56" wide compartment over the wheel well and (1) 2‐Arm Ladder Rack. The ladder rack is to be sanded DA finish and includes amber lights on each end to visually indicate when the rack is in motion.
Officer side body with full height 24" wide forward and 36" wide rearward compartmentation. Includes (1) 56" wide compartment over the wheel well.
Officer side body with full height 30" wide forward and 36" wide rearward compartmentation. Includes (1) 56" wide compartment over the wheel well.
Officer side body with full height 24" wide forward and 50" wide rearward extended compartmentation. Includes (1) 56" wide compartment over the wheel well.
Officer side body with full height 30" wide forward and 50" wide rearward extended compartmentation. Includes (1) 56" wide compartment over the wheel well.
Officer side body with full height 36" wide forward and 50" wide rearward extended compartmentation. Includes (1) 56" wide compartment over the wheel well.
Officer side body with full height 24" wide forward and 50" wide rearward enhanced extended compartmentation. Includes (1) 56" wide compartment over the wheel well.
Officer side body with full height 30" wide forward and 50" wide rearward enhanced extended compartmentation. Includes (1) 56" wide compartment over the wheel well.
Officer side body with full height 36" wide forward and 50" wide rearward enhanced extended compartmentation. Includes (1) 56" wide compartment over the wheel well.
Officer side body with full height 52" wide forward and 52" wide rearward compartmentation. Includes (1) 56" wide compartment over the wheel well.
Officer side body with full height 36" wide forward and 50" wide rearward compartmentation. Includes (1) 56" wide compartment over the wheel well.
Officer side body with full height 30" wide forward and 50" wide rearward compartmentation. Includes (1) 56" wide compartment over the wheel well.
PRICE
$20,433.00
$1,909.00
$6,065.00
$1,526.00
$640.00
$6,879.00
$29,909.00
$8,985.00
$9,612.00
$9,612.00
$10,244.00
$10,912.00
$9,902.00
$10,529.00
$11,200.00
$12,597.00
$11,200.00
$10,529.00
Option No.
3120‐0257
3120‐0258
3120‐0259
3120‐0260
3120‐0261
3120‐0262
3120‐0263
3120‐0264
3120‐0265
3120‐0266
3120‐0268
3120‐0269
3120‐0270
3120‐0271
3120‐0272
3120‐0273
3120‐0274
3120‐0275
3120‐0276
Description
Officer side body with full height 24" wide forward and 50" wide rearward compartmentation. Includes (1) 56" wide compartment over the wheel well.
Officer 3/4 side body with full height 24" wide forward and 50" wide rearward compartmentation. Includes (1) 56" wide compartment over the wheel well.
Officer 3/4 side body with full height 30" wide forward and 50" wide rearward compartmentation. Includes (1) 56" wide compartment over the wheel well.
Officer 3/4 side body with full height 36" wide forward and 50" wide rearward enhanced extended compartmentation. Includes (1) 56" wide compartment over the wheel well.
Officer half side body with 24" wide forward and 50" wide rearward compartmentation. Includes adjustable ladder tracks.
Officer half side body with 30" wide forward and 50" wide rearward compartmentation. Includes adjustable ladder tracks.
Officer half side body with 36" wide forward and 50" wide rearward enhanced extended compartmentation. Includes adjustable ladder tracks.
Officer side body with full height 24" wide forward and 50" wide rearward compartmentation. Includes (1) 33" wide compartment over the wheel well and (1) Zico Overhead Ladder Rack.
Officer side body with full height 30" wide forward and 50" wide rearward compartmentation. Includes (1) 33" wide compartment over the wheel well and (1) Zico Overhead Ladder Rack.
Officer side body with full height 36" wide forward and 50" wide rearward compartmentation. Includes (1) 33" wide compartment over the wheel well and (1) Zico Overhead Ladder Rack.
Officer side body with full height 42" wide forward and 56" wide rearward compartmentation. Includes (1) 56" wide compartment over the wheel well.
Officer side body with full height 36" wide forward and 42" wide rearward compartmentation. Includes (1) 56" wide compartment over the wheel well and one (1)ladder storage tunnel and access door at rear.
Officer side body with full height 42" wide forward and 56" wide rearward compartmentation. Includes (1) 33" wide compartment over the wheel well and (1) Zico Overhead Ladder Rack.
Officer 3/4 side body with full height 42" wide forward and 56" wide rearward enhanced extended compartmentation. Includes (1) 56" wide compartment over the wheel well.
Officer half side body with 42" wide forward and 56" wide rearward enhanced extended compartmentation. Includes adjustable ladder tracks.
Officer side body with full height 36" wide forward and 50" wide rearward enhanced extended compartmentation. Includes (1) 20" wide compartment over the wheel well and (1) E‐One center mounted Overhead Ladder Rack.
Officer side body with full height 36" wide forward and 50" wide rearward enhanced extended compartmentation. Includes (1) 56" wide compartment over the wheel well.
Officer side body with full height 42" wide forward and 56" wide rearward enhanced extended compartmentation. Includes (1) 56" wide compartment over the wheel well.
Officer side body with full height 48" wide forward and 62" wide rearward enhanced extended compartmentation. Includes (1) 56" wide compartment over the wheel well.
PRICE
$9,902.00
$6,533.00
$6,924.00
$7,344.00
$5,412.00
$5,724.00
$6,060.00
$16,457.00
$17,083.00
$17,754.00
$11,872.00
$14,691.00
$18,188.00
$7,796.00
$6,420.00
$17,754.00
$11,907.00
$12,677.00
$13,502.00
Option No.
3120‐0277
3120‐0278
3120‐0279
3120‐0280
3120‐0281
3120‐0282
3120‐0283
3120‐0284
3120‐0285
3120‐0286
3120‐0287
3120‐0288
3120‐0290
3120‐0291
3120‐0292
3120‐0293
3120‐0294
Description
Officer side body with full height 60" wide forward and 56" wide rearward enhanced extended compartmentation. Includes (1) 56" wide compartment over the wheel well.
Officer side body with full height 36" wide forward and 50" wide rearward enhanced extended compartmentation. Includes (1) 33" wide compartment over the wheel well and (1) Zico Overhead Ladder Rack.
Officer side body with full height 42" wide forward and 56" wide rearward enhanced extended compartmentation. Includes (1) 33" wide compartment over the wheel well and (1) Zico Overhead Ladder Rack.
Officer side body with full height 48" wide forward and 62" wide rearward enhanced extended compartmentation. Includes (1) 33" wide compartment over the wheel well and (1) Zico Overhead Ladder Rack.
Officer side body with full height 60" wide forward and 56" wide rearward enhanced extended compartmentation. Includes (1) 33" wide compartment over the wheel well and (1) Zico Overhead Ladder Rack.
Officer side body with full height 36" wide forward and 50" wide rearward enhanced extended compartmentation. Includes (1) 56" wide compartment over the wheel well and one (1) storage tunnel.
Officer side body with full height 42" wide forward and 56" wide rearward enhanced extended compartmentation. Includes (1) 56" wide compartment over the wheel well and one (1) storage tunnel.
Officer side body with full height 48" wide forward and 62" wide rearward enhanced extended compartmentation. Includes (1) 56" wide compartment over the wheel well and one (1) storage tunnel.
Officer side body with full height 60" wide forward and 56" wide rearward enhanced extended compartmentation. Includes (1) 56" wide compartment over the wheel well and one (1) storage tunnel.
Officer 3/4 side body with full height 30" wide forward and 36" wide rearward compartmentation. Includes (1) 56" wide compartment over the wheel well.
Officer side body with upper and lower compartmentation. Includes 24" wide forward and 36" wide rearward lower compartments and (2) opening upper compartments. Includes (1) Zico Overhead Ladder Rack centered mounted between upper compartments.
Officer full height side body with upper and lower compartmentation. Includes 42" wide forward and 42" wide rearward lower compartments and (2) opening upper compartments. Includes (1) Zico Overhead Ladder Rack mounted centered between upper compartments.
Officer side body with full height 30" wide forward and 50" wide rearward enhanced extended compartmentation. Includes (1) 56" wide compartment over the wheel well and one (1) storage tunnel.
Officer side body with full height 50" wide forward and 50" wide rearward enhanced extended compartmentation. Includes (1) 33" wide compartment over the wheel well and (1) Zico Overhead Ladder Rack.
Officer side body with full height 56" wide forward and 56" wide rearward enhanced extended compartmentation. Includes (1) 33" wide compartment over the wheel well and (1) Zico Overhead Ladder Rack.
Officer side body with full height 62" wide forward and 62" wide rearward enhanced extended compartmentation. Includes (1) 33" wide compartment over the wheel well and (1) Zico Overhead Ladder Rack.
Officer side body with full height 50" wide forward and 50" wide rearward enhanced extended compartmentation. Includes (1) 56" wide compartment over the wheel well.
PRICE
$14,384.00
$18,920.00
$19,690.00
$20,513.00
$21,396.00
$14,825.00
$15,596.00
$16,420.00
$17,299.00
$5,775.00
$15,988.00
$18,008.00
$14,110.00
$19,690.00
$20,512.00
$21,335.00
$12,677.00
Option No.
3120‐0295
3120‐0296
3120‐0297
3120‐0298
3120‐0299
3120‐0300
3120‐0301
3120‐0302
3120‐0303
3120‐0304
3120‐0305
3120‐0306
3120‐0307
3120‐0308
3120‐0309
3120‐0310
3120‐0311
3120‐0312
Description
Officer side body with full height 56" wide forward and 56" wide rearward enhanced extended compartmentation. Includes (1) 56" wide compartment over the wheel well.
Officer side body with full height 62" wide forward and 62" wide rearward enhanced extended compartmentation. Includes (1) 56" wide compartment over the wheel well.
Officer side body with full height 50" wide forward and 50" wide rearward enhanced extended compartmentation. Includes (1) 56" wide compartment over the wheel well and one (1) ladder storage tunnel and access door at rear.
Officer side body with full height 56" wide forward and 56" wide rearward enhanced extended compartmentation. Includes (1) 56" wide compartment over the wheel well and one (1) ladder storage tunnel and access door at rear.
Officer side body with full height 62" wide forward and 62" wide rearward enhanced extended compartmentation. Includes (1) 56" wide compartment over the wheel well and one (1) ladder storage tunnel and access door at rear.
Officer side body with full height 42" wide forward and 56" wide rearward enhanced extended compartmentation. Includes (1) 56" wide compartment over the wheel well and one (1) storage tunnel and access door at rear.
Officer side tunnel to hold: [#LOC].
Officer half side body with 42" wide forward and 42" wide rearward compartmentation.
Officer side body with full height 36" wide forward and 36" wide rearward compartmentation. Includes (1) 56" wide compartment over the wheel well and 30 degree rear body angle for greater angle of departure.
Officer side body with full height 62" wide forward and 62" wide rearward enhanced extended compartmentation. Includes (1) 56" wide compartment over the wheel well.
Stainless steel officer side body with full height 48" wide forward and 48" wide (interior) rearward compartmentation. Includes (1) 60" wide compartment over the wheel well and one (1) ladder storage tunnel and access door at rear with push‐button latch. Upper area of ladder storage to have stop at 8' and be used for misc. storage.
Officer side body with 62" wide full height forward enhanced extended compartment, 36" wide half height second forward compartment and 50" wide half height rearward compartmentation. Includes adjustable ladder tracks.
Officer side body with full height 24" wide forward and 56" wide rearward extended compartmentation. Includes (1) 33" wide compartment over the wheel well and (1) Zico Overhead Ladder Rack.
Officer side body with full height 24" wide forward and 50" wide rearward enhanced extended compartmentation. Includes (1) 56" wide compartment over the wheel well and one (1) ladder storage tunnel and access door at rear.
Officer side body with upper and lower compartmentation. Includes 36" wide forward and 50" wide rearward extended lower compartmentation and (2) opening upper compartments with (1) Zico Overhead Ladder Rack centered between the compartments.
Officer side body with full height 36" wide forward and 36" wide rearward compartmentation. Includes (1) 33" wide compartment over the wheel well, one (1) storage tunnel and (1) Zico Overhead Ladder Rack.
Officer side body with full height 42" wide forward and 42" wide rearward compartmentation. Includes (1) 33" wide compartment over the wheel well, one (1) storage tunnel and (1) Zico Overhead Ladder Rack.
Officer side body with full height 48" wide forward and 48" wide rearward compartmentation. Includes (1) 33" wide compartment over the wheel well, one (1) storage tunnel and (1) Zico Overhead Ladder Rack.
PRICE
$13,502.00
$14,323.00
$15,596.00
$16,419.00
$17,240.00
$15,596.00
$640.00
$5,504.00
$10,631.00
$13,465.00
$17,787.00
$18,556.00
$17,153.00
$16,228.00
$21,107.00
$20,935.00
$21,705.00
$22,529.00
Option No.
3120‐0313
3120‐0314
3120‐0315
3120‐0316
3120‐0317
3120‐0318
Description
Officer side body with full height 60" wide forward and 42" wide rearward compartmentation. Includes (1) 33" wide compartment over the wheel well, one (1) storage tunnel and (1) Zico Overhead Ladder Rack.
Officer side body with full height 36" wide forward and 50" wide rearward enhanced extended compartmentation. Includes (1) 33" wide compartment over the wheel well, one (1) storage tunnel and (1) Zico Overhead Ladder Rack.
Officer side body with full height 42" wide forward and 56" wide rearward enhanced extended compartmentation. Includes (1) 33" wide compartment over the wheel well, one (1) storage tunnel and (1) Zico Overhead Ladder Rack.
Officer side body with full height 48" wide forward and 62" wide rearward enhanced extended compartmentation. Includes (1) 33" wide compartment over the wheel well, (1) Zico Overhead Ladder Rack and one (1) storage tunnel.
Officer side body with full height 60" wide forward and 56" wide rearward enhanced extended compartmentation. Includes (1) 33" wide compartment over the wheel well, one (1) storage tunnel and (1) Zico Overhead Ladder Rack.
Officer side body with full height 36" wide forward and 50" wide rearward enhanced extended compartmentation (2008 body design) with (1) 56" wide compartment over the wheel well and one (1) storage tunnel.
PRICE
$23,411.00
$21,835.00
$22,608.00
$23,431.00
$24,314.00
$20,204.00
3120‐0326
Officer half side body with 20" wide forward and 50" wide rearward extended compartmentation. Includes adjustable ladder tracks.
Officer side upper body extension. Does not include external upper doors. External framework and platework only. Platework shall be recessed.
Stainless steel officer side body with full height 30" wide forward and 58" wide rearward enhanced extended compartmentation. Includes (1) 54" wide compartment over the wheel well.
Stainless steel officer side body with full height 40" wide forward and 58" wide rearward enhanced extended compartmentation. Includes (1) 54" wide compartment over the wheel well.
Stainless steel officer side body with full height 48" wide forward and 58" wide rearward enhanced extended compartmentation. Includes (1) 54" wide compartment over the wheel well.
Stainless steel officer side body with full height 30" wide forward and 40" wide rearward compartmentation. Includes (1) 54" wide compartment over the wheel well.
Stainless steel officer side body with full height 40" wide forward and 40" wide rearward compartmentation. Includes (1) 54" wide compartment over the wheel well.
Stainless steel officer side body with full height 48" wide forward and 40" wide rearward compartmentation. Includes (1) 54" wide compartment over the wheel well.
3120‐0327
Stainless steel officer half side body with 30" wide forward and 40" wide rearward compartmentation. Includes adjustable ladder tracks.
$4,809.00
3120‐0328
Stainless steel officer half side body with 40" wide forward and 40" wide rearward compartmentation. Includes adjustable ladder tracks.
$5,504.00
3120‐0329
Stainless steel officer half side body with 48" wide forward and 40" wide rearward compartmentation. Includes adjustable ladder tracks.
Stainless steel officer 3/4 side body with full height 30" wide forward and 40" wide rearward compartmentation. Includes (1) 54" wide compartment over the wheel well.
$5,890.00
3120‐0319
3120‐0320
3120‐0321
3120‐0322
3120‐0323
3120‐0324
3120‐0325
3120‐0330
$5,018.00
$2,219.00
$10,529.00
$11,922.00
$12,690.00
$9,612.00
$11,005.00
$11,773.00
$6,011.00
Option No.
3120‐0331
3120‐0332
3120‐0333
3120‐0334
3120‐0335
3120‐0336
3120‐0337
3120‐0338
3120‐0339
3120‐0340
3120‐0341
3120‐0342
3120‐0343
3120‐0344
3120‐0346
3120‐0347
3120‐0348
3120‐0349
3120‐0350
Description
Stainless steel officer 3/4 side body with full height 40" wide forward and 40" wide rearward compartmentation. Includes (1) 54" wide compartment over the wheel well.
Stainless steel officer 3/4 side body with full height 48" wide forward and 40" wide rearward compartmentation. Includes (1) 54" wide compartment over the wheel well.
Stainless steel officer side body with full height 30" wide forward and 40" wide rearward compartmentation. Includes (1) 38" wide compartment over the wheel well and (1) Zico Overhead Ladder Rack.
Stainless steel officer side body with full height 40" wide forward and 40" wide rearward compartmentation. Includes (1) 38" wide compartment over the wheel well and (1) Zico Overhead Ladder Rack.
Stainless steel officer side body with full height 48" wide forward and 40" wide rearward compartmentation. Includes (1) 38" wide compartment over the wheel well and (1) Zico overhead ladder rack.
Stainless steel officer side body with full height 30" wide forward and 58" wide rearward enhanced extended compartmentation. Includes (1) 38" wide compartment over the wheel well and (1) Zico Overhead Ladder Rack.
Stainless steel officer side body with full height 40" wide forward and 58" wide rearward enhanced extended compartmentation. Includes (1) 38" wide compartment over the wheel well and (1) Zico Overhead Ladder Rack.
Stainless steel officer side body with full height 48" wide forward and 58" wide rearward enhanced extended compartmentation. Includes (1) 38" wide compartment over the wheel well and (1) Zico Overhead Ladder Rack.
Officer half side stainless steel body with 30" wide forward and 58" wide rearward enhanced extended compartmentation. Includes adjustable ladder tracks.
Officer half side stainless steel body with 40" wide forward and 58" wide rearward enhanced extended compartmentation. Includes adjustable ladder tracks.
Officer half side stainless steel body with 48" wide forward and 58" wide rearward enhanced extended compartmentation. Includes adjustable ladder tracks.
Officer 3/4 side stainless steel body with 30" wide forward and 58" wide rearward enhanced extended compartmentation. Includes (1) 54" wide compartment over the wheel well.
Officer 3/4 side stainless steel body with 40" wide forward and 58" wide rearward enhanced extended compartmentation. Includes (1) 54" wide compartment over the wheel well.
Officer 3/4 side stainless steel body with 48" wide forward and 58" wide rearward enhanced extended compartmentation. Includes (1) 54" wide compartment over the wheel well.
Officer half side body with (2) forward compartments (48" and 30" wide) and one rearward area for locating of side tank dump.
Officer half side body with (2) forward compartments (48" and 30" wide) and (1) rearward compartment (24").
Officer 3/4 side body with (2) lower forward compartments (48" and 30" wide), (3) upper compartments (54") and one lower rearward area for locating of side tank dump.
Officer 3/4 side body with (2) lower forward compartments (48" and 30" wide), (3) upper compartments (54") and (1) lower rearward compartment (24").
Officer full height side body with (2) lower forward compartments (48" and 30" wide), (3) upper compartments (54") and one lower rearward area for locating of side tank dump.
PRICE
$6,879.00
$7,361.00
$16,167.00
$17,559.00
$18,327.00
$17,083.00
$18,475.00
$19,244.00
$5,724.00
$6,420.00
$6,806.00
$6,924.00
$7,796.00
$8,278.00
$5,011.00
$5,890.00
$6,930.00
$7,810.00
$8,850.00
Option No.
3120‐0351
3120‐0352
3120‐0353
3120‐0356
3120‐0357
3120‐0358
3120‐0359
3120‐0360
3120‐0361
3120‐0362
3120‐0363
3120‐0364
3120‐0365
3120‐0366
3120‐0367
3120‐0368
3120‐0369
3120‐0370
Description
Officer full height side body with (2) lower forward compartments (48" and 30" wide), (3) upper compartments (54") and (1) lower rearward compartment (24").
Officer full height side body with (2) full height, rescue style, forward compartments (48" and 30" wide), (1) upper compartment (61" and offset rearward of the rack opening) and one lower rearward area for locating of side tank dump.
Officer full height side body with (2) full height, rescue style, forward compartments (48" and 30" wide), (1) upper compartment (61" and offset rearward of the rack opening) and (1) lower rearward compartment (24").
Officer full height side body with (2) lower forward compartments (48" and 30" wide), (3) upper compartments (54") with rear compartment face access door for portable tank storage and one lower rearward area for locating of side tank dump.
Officer full height side body with (2) lower forward compartments (48" and 30" wide), (3) upper compartments (54") with rear compartment face access door for portable tank storage and (1) lower rearward compartment (24").
Officer half side body with 60" wide forward and 42" wide rearward compartmentation.
Officer side body with full height 24" wide forward and 50" wide rearward enhanced extended compartmentation. Includes (1) 56" wide compartment over the wheel well and one (1) storage tunnel.
2‐Arm Ladder Rack on Officer Side. The ladder rack includes amber lights on each end to visually indicate when the rack is in motion. Restricts the top folding step (if optioned) from closing completely. Includes mounting bracket (if required, matching rear compartment face or compartment wrap finish) for components mounted on rear compartment face or hosebed upper side assembly.
Storage tunnel door to be hinged to the outboard side of the body.
Officer full height side body with (2) lower forward compartments (48" and 30" wide), (1) upper forward compartment (54") with rear compartment face access door (wired to door ajar) for enclosed ladder storage and (1) lower rearward compartment (24").
Officer full height side body with (2) full height, rescue style, forward compartments (48" and 30" wide), (2) upper compartments (40" wide) and one lower rearward area for locating of side tank dump.
Officer full height side body with (2) full height, rescue style, forward compartments (48" and 30" wide), (2) upper compartment (40" wide) and (1) lower rearward compartment (24").
(1) officer side roof top compartments with extra width to inboard side. Includes hinged raised compartment lid with turn latches, grab handle(s) and gas shock hold open and drain line(s) ran to below body. The lid to have (1) bracket mounted LED light and to be wired to door ajar indicator in cab.
Stainless steel officer side body with full height 48" wide forward and 48" wide rearward compartmentation with reduced upper depth. Includes (1) 54" wide compartment over the wheel well and (1) storage tunnel.
Stainless steel officer side body with full height 54" wide forward and 54" wide rearward compartmentation with reduced upper depth. Includes (1) 54" wide compartment over the wheel well and (1) storage tunnel.
Stainless steel officer side body with full height 60" wide forward and 60" wide rearward compartmentation with reduced upper depth. Includes (1) 54" wide compartment over the wheel well and (1) storage tunnel.
Stainless steel officer side body with full height 48" wide forward and 48" wide rearward compartmentation. Includes 54" wide compartment over the wheel well and a dual arm hydraulic overhead ladder rack.
Stainless steel officer side body with full height 54" wide forward and 54" wide rearward compartmentation. Includes 54" wide compartment over the wheel well and a dual arm hydraulic overhead ladder rack.
PRICE
$9,731.00
$8,850.00
$9,731.00
$10,249.00
$11,128.00
$6,302.00
$13,395.00
$16,399.00
$0.00
$12,524.00
$8,850.00
$9,731.00
$5,466.00
$15,515.00
$16,758.00
$18,000.00
$12,597.00
$13,605.00
Option No.
3120‐0371
3120‐0372
3120‐0373
3120‐0374
3120‐0375
3120‐0376
3120‐0377
3120‐0378
3120‐0379
3120‐0380
3120‐0381
3120‐0382
3120‐0383
3120‐0384
3120‐0385
3120‐0386
3120‐0387
3120‐0388
3120‐0389
3120‐0390
Description
Stainless steel officer side body with full height 60" wide forward and 60" wide rearward compartmentation. Includes 54" wide compartment over the wheel well and a dual arm hydraulic overhead ladder rack.
Officer side 1/2 height body with 34" forward / 54" rearward compartment and adjustable ladder brackets.
Officer side 3/4 height enhanced extended body with 34" forward / 54" rearward compartment. Includes drop down ladder rack. Rack sized for (1) 24' 2‐section and (1) 14' roof.
Officer side full height enhanced extended body with 34" forward / 54" rearward compartment. Includes overhead ladder rack with rack arm drop down cover plate.
Officer side storage tunnel to hold (1) 24' 2‐section ladder, (1) 14' roof ladder, (1) 10' attic ladder with feet and (2) pike poles. Set‐up for Alco‐Lite ladders.
Officer side storage tunnel to hold (1) 24' 2‐section ladder, (1) 14' roof ladder, (1) 10' attic ladder with feet and (2) pike poles. Set‐up for Duo‐Safety ladders.
Officer half side tandem body with 30" wide forward and 30" wide rearward compartmentation.
Officer half side tandem body with 42" wide forward and 42" wide rearward compartmentation.
Officer half side tandem body with 60" wide forward and 54" wide rearward compartmentation.
Officer 3/4 side tandem body with full height 30" wide forward and 30" wide rearward compartmentation. Includes (2) 51.5" wide compartments over the wheel well.
Officer 3/4 side tandem body with full height 42" wide forward and 42" wide rearward compartmentation. Includes (2) 51.5" wide compartments over the wheel well.
Officer 3/4 side tandem body with full height 60" wide forward and 54" wide rearward compartmentation. Includes (2) 51.5" wide compartments over the wheel well.
Officer side tandem body with upper and lower compartmentation. Includes 30" wide forward and 30" wide rearward compartments and (4) opening upper compartments.
Officer side tandem body with upper and lower compartmentation. Includes 42" wide forward and 42" wide rearward compartments and (4) opening upper compartments.
Officer side tandem body with upper and lower compartmentation. Includes 60" wide forward and 54" wide rearward compartments and (4) opening upper compartments.
Officer side tandem body with upper and lower compartmentation. Includes 30" wide forward and 30" wide rearward compartments and (4) opening upper compartments. Includes overhead rack opening centered between upper compartments.
Officer side tandem body with upper and lower compartmentation. Includes 42" wide forward and 42" wide rearward compartments and (4) opening upper compartments. Includes overhead rack opening centered between upper compartments.
Officer side tandem body with upper and lower compartmentation. Includes 60" wide forward and 54" wide rearward compartments and (4) opening upper compartments. Includes overhead rack opening centered between upper compartments.
Officer side tandem body with full height 30" wide forward and 30" wide rearward compartmentation. Includes (2) 51.5" wide compartments over the wheel well.
Officer side tandem body with full height 42" wide forward and 42" wide rearward compartmentation. Includes (2) 51.5" wide compartments over the wheel well.
PRICE
$14,614.00
$0.00
$0.00
$0.00
$0.00
$0.00
$7,519.00
$8,214.00
$9,013.00
$8,707.00
$9,574.00
$10,570.00
$12,756.00
$14,150.00
$15,773.00
$13,265.00
$14,714.00
$16,403.00
$12,309.00
$13,701.00
Option No.
3120‐0391
3120‐0392
3120‐0393
3120‐0394
3120‐0395
3120‐0396
3120‐0397
3120‐0398
3120‐0399
3120‐0400
3120‐0401
3120‐0402
3120‐0403
3120‐0404
3120‐0405
3120‐0406
3120‐0407
3120‐0408
3120‐0409
Description
Officer side tandem body with full height 60" wide forward and 54" wide rearward compartmentation. Includes (2) 51.5" wide compartments over the wheel well.
Officer side tandem body with full height 30" wide forward and 30" wide rearward compartmentation. Includes (2) 42" wide compartments over the wheel well and overhead rack opening centered between upper compartments.
Officer side tandem body with full height 42" wide forward and 42" wide rearward compartmentation. Includes (2) 42" wide compartments over the wheel well and overhead rack opening centered between upper compartments.‐
Officer side tandem body with full height 60" wide forward and 54" wide rearward compartmentation. Includes (2) 42" wide compartments over the wheel well and overhead rack opening centered between upper compartments.
Officer half side body with 36" wide forward and 36" wide rearward compartmentation.
Officer 3/4 side body with full height 36" wide forward and 36" wide rearward compartmentation. Includes (1) 56" wide compartment over the wheel well.
Officer side body with full height 36" wide forward and 36" wide rearward compartmentation. Includes (1) 33" wide compartment (forward) over the wheel well and (1) Zico Overhead Ladder Rack.
Officer half side body with 42" wide forward and 42" wide rearward compartmentation.
Officer 3/4 side body with full height 42" wide forward and 42" wide rearward compartmentation. Includes (1) 56" wide compartment over the wheel well.
Officer side body with full height 42" wide forward and 42" wide rearward compartmentation. Includes (1) 33" wide compartment (forward) over the wheel well and (1) Zico Overhead Ladder Rack.
Officer side body with full height 42" wide forward and 50" wide rearward compartmentation. Includes (1) 33" wide compartment over the wheel well and (1) Zico Overhead Ladder Rack.
Officer half side tandem body with with 42" wide forward and one rearward area for locating of side tank dump rearward of the wheel well.
Officer side body with full height 60" wide forward and 56" wide rearward compartmentation. Includes (1) 56" wide compartment over the wheel well and one (1) storage tunnel located behind the upper (3) compartment back walls.
Officer half side body with 36" wide forward and 31" wide rearward compartmentation. Includes adjustable ladder tracks mounted to outside of hosebed 3x3 and to run full height for max adjustments..
Officer side body with full height 46" wide forward and 56" wide rearward enhanced extended compartmentation. Includes (1) 56" wide compartment over the wheel well.
Officer side body with full height 50" wide forward and 50" wide rearward compartmentation. Includes (1) 33" wide compartment over the wheel well and (1) Zico Overhead Ladder Rack.
Officer side body with full height 42" wide forward and 56" wide rearward enhanced extended compartmentation. Includes (1) 56" wide compartment over the wheel well. Rescue Pumper style compartments for use with low hosebed.
Officer side body with full height 36" wide forward and 50" wide rearward enhanced extended compartmentation. Includes (1) 56" wide compartment over the wheel well and one (1) storage tunnel area directly behind the upper compartment area (accessed from the rear end assembly).
Officer half side body with 42" wide forward and 56" wide rearward enhanced extended compartmentation. For use with a Zico drop down ladder rack.
PRICE
$15,292.00
$12,799.00
$14,247.00
$15,904.00
$5,147.00
$6,011.00
$16,838.00
$5,504.00
$6,879.00
$17,559.00
$17,972.00
$8,502.00
$16,399.00
$5,147.00
$13,502.00
$20,494.00
$14,401.00
$12,310.00
$6,420.00
Option No.
3120‐0410
3120‐0411
3120‐0412
3120‐0413
3120‐0414
3120‐0415
3120‐0416
3120‐0417
3120‐0418
3120‐0419
3120‐0420
3120‐0421
3120‐0422
3120‐0423
3120‐0424
3120‐0425
Description
Officer side body with full height 60" wide forward and 62" wide rearward enhanced extended compartmentation. Includes (1) 56" wide compartment over the wheel well.
Officer side body with full height 42" wide forward and 56" wide rearward enhanced extended compartmentation. Includes (1) 56" wide compartment over the wheel well.
2‐Arm Ladder Rack on Officer Side. The ladder rack includes amber lights on each end to visually indicate when the rack is in motion. Restricts the top folding step (if optioned) from closing completely. Includes mounting bracket (matching rear compartment face or compartment wrap finish) for components mounted on rear compartment face including the stop/tail/turn lights.
Officer side body with full height 60" wide forward and 56" wide rearward compartmentation. Includes (1) 33" wide compartment over the wheel well and (1) Zico Overhead Ladder Rack.
Officer half side body with (2) forward compartments (39" and 39" wide) and (1) rearward compartment (24").
Officer full height side body with upper and lower compartmentation. Includes 48" wide forward and 62" wide enhanced extended rearward lower compartments and (3) opening upper compartments and (1) Zico Overhead Ladder Rack. Upper compartments to be (1) 56" wide forward, Overhead ladder rack, (2) 45" wide compartments rearward of rack.
Officer full height side body with upper and lower compartmentation. Includes 60" wide forward and 42" wide rearward lower compartments and (3) opening upper compartments and (1) Zico Overhead Ladder Rack.
Officer side body with full height 60" wide forward and 56" wide rearward compartmentation. Includes (1) 56" wide compartment over the wheel well. For use with ladders stored in hosebed.
Officer 3/4 side body with full height 42" wide forward and 56" wide rearward enhanced extended compartmentation. Includes (1) 56" wide compartment over the wheel well. Compartments raised 8" due to roll‐up doors to allow for addtional storage room.
Officer extruded half side tandem body with 74" wide forward and 34" wide rearward compartmentation.For use with wetside narrow tank application.
Officer side body with full height 36" wide forward and 45" wide rearward compartmentation. Includes (1) 56" wide compartment over the wheel well.
Officer side diamond plate roof top compartment. Includes (2) hinged lift‐up access doors with turn latches and grab handle(s) and (1) vertical hinged access door at the rear with push button latch to be. Each lid to have (1) bracket mounted LED light and to be wired to door ajar indicator in cab.
Officer side body with full height 19.5" wide forward and 31" wide rearward compartmentation. Includes (1) 40" wide compartment over the wheel well.
Officer side body with full height 32" wide forward and 50" wide rearward compartmentation. Includes (1) 56" wide compartment over the wheel well and one (1) storage tunnel beside the water tank.
Officer side body with full height 54" wide forward and 48" wide rearward compartmentation. Includes (1) 56" wide compartment over the wheel well and one (1) storage tunnel located behind the upper (3) compartment back walls.
Officer side body with half height 36" wide forward (above fuel fill area) and full height 50" wide rearward enhanced extended compartmentation. Includes (1) 56" wide compartment over the wheel well. Area below forward compartment will be for mounting of fuel fill.
PRICE
$14,824.00
$13,251.00
$15,895.00
$20,494.00
$7,041.00
$20,330.00
$19,269.00
$13,480.00
$11,866.00
$5,468.00
$11,820.00
$2,292.00
$9,902.00
$10,735.00
$15,553.00
$11,200.00
Option No.
3120‐0426
3120‐0427
3120‐0428
3120‐0429
3120‐0430
3120‐0431
3120‐0432
3120‐0433
3120‐0434
3120‐0435
3120‐0436
3120‐0437
3120‐0438
3120‐0439
3120‐0440
3120‐0441
Description
Officer side body with full height 26" and 56" wide forward compartments and 56" wide rearward compartmentation. Includes (1) 56" wide compartment over the wheel well and one (1) storage tunnel.
Officer side body with full height 60" wide front and 54" wide rear compartments. Includes (1) 60" wide compartment over the wheel well and one (1) storage tunnel located behind reduced upper depth compartments. SS eMAX only.
Officer side body with full height 36" wide forward and 50" wide rearward enhanced extended compartmentation. Includes (1) 33" wide compartment over the wheel well and (1) Zico Overhead Ladder Rack. Area below forward compartment will be for mounting of fuel fill.
Officer side tandem body with upper and lower compartmentation. Includes 60" wide forward and 54" wide rearward compartments and (1) opening forward upper compartment with painted panels rearward.
Right Side Exterior Compartments. R1, 60" wide x 63" high x 48" deep (over frame) full height with vertically hinged doors. R2, 58" wide x 63" high x 27.5" deep (over frame) full height with vertically hinged doors. R3, 60" wide x 33" high x 27.5" deep full height with vertically hinged doors. R4, 40" wide x 63" high x 27.5" deep (over frame) full height with vertically hinged doors.
Officer side body with full height 36" wide forward and 36" wide rearward compartmentation. Includes (1) 56" wide compartment over the wheel well.
Officer side body with full height 42" wide forward and 42" wide rearward compartmentation. Includes (1) 56" wide compartment over the wheel well.
Officer side body with upper and lower compartmentation. Includes 36" wide forward and 36" wide rearward lower compartments and (3) opening upper compartments.
Officer side body with upper and lower compartmentation. Includes 42" wide forward and 42" wide rearward lower compartments and (3) opening upper compartments.
Officer 3/4 side body with with upper and lower compartmentation. Includes 36" wide forward and 36" wide rearward lower compartments and (3) opening upper compartments.
Officer 3/4 side body with with upper and lower compartmentation. Includes 42" wide forward and 42" wide rearward lower compartments and (3) opening upper compartments.
Rear aluminum smooth plate painted job color vertical hinged door on officer side roof top compartments. Includes thumb latch and wiring for door ajar switch.
Stainless steel officer side body with full height 36" wide forward and 48" wide rearward compartmentation. Includes 54" wide compartment over the wheel well and a dual arm hydraulic overhead ladder rack.
Officer side body with full height 26" and 56" wide forward and 56" wide rearward compartmentation. Includes (1) 33" wide compartment over the wheel well and (1) Zico Overhead Ladder Rack.
Stainless steel officer side body with 76" full height interior, 48" wide forward and 40" wide rearward compartmentation. Includes (1) 54" wide compartment over the wheel well.
Officer half side body with 36" wide forward and 56" wide rearward enhanced extended compartmentation. Includes adjustable ladder tracks.
PRICE
$17,767.00
$20,005.00
$18,920.00
$16,880.00
$7,622.00
$10,297.00
$11,005.00
$10,733.00
$11,454.00
$6,452.00
$7,322.00
$220.00
$12,646.00
$21,891.00
$12,219.00
$6,420.00
Option No.
3120‐0442
3120‐0443
3120‐0444
3120‐0445
3120‐0446
3120‐0447
3120‐0448
3120‐0449
3120‐0450
3120‐0451
3120‐0452
3120‐0453
3120‐0454
3120‐0455
3120‐0456
3120‐0457
Description
Officer side tandem body with upper and lower compartmentation. Includes 30" wide forward and 54" wide rearward compartments and (4) opening upper compartments. Includes overhead rack opening centered between upper compartments. Includes offseting upper compartments forward due to deck gun location and access panel on upper rear compartment face to deck gun piping.
(1) officer side roof top compartment forward of hard suction storage area and (2) roof top comaprtments over hard suction storage area. Includes hinged raised compartment lids with turn latches and grab handle(s). The lids to have (1) bracket mounted LED light and to be wired to door ajar indicator in cab. Includes partition between roof top compartment and hard suction storage area. Floor to be provided above the hard suction storage area to use remaining area above.
Officer half side body with 36" wide forward and 56" wide rearward enhanced extended compartmentation. Includes adjustable ladder tracks. 8" compartment raise to allow for taller opening with roll‐up doors and smooth plate above wheel well area.
Officer side tandem body with 60" wide forward and 54" wide rearward compartmentation. Forward compartment to be full height, rearward to be half height.
Officer side diamond plate roof top compartment. Includes smooth plate painted vertical hinged access door at the rear with push button latch to be wired to door ajar indicator in cab.
Officer side body with full height 54" wide forward and 36" wide rearward compartmentation. Includes (1) 33" wide compartment over the wheel well and (1) Zico Overhead Ladder Rack.
Officer side roof top assembly. Does not include external upper doors or internal platework. External framework and platework only.
Officer side body with full height 60" wide forward and 56" wide rearward compartmentation. Includes (1) 56" wide compartment over the wheel well.
Officer half side body with 36" wide forward and 36" wide rearward compartmentation. Includes 30 degree rear body angle for greater angle of departure.
Officer 3/4 height side body with 66" wide forward and 42" wide rearward compartmentation. Includes (1) 56" wide compartment over the wheel well. For use with custom chassis only.
Officer full height side body with 66" wide forward and 42" wide rearward compartmentation. Includes (1) 56" wide compartment over the wheel well. For use with custom chassis only.
Officer 3/4 side tandem body with full height 42" wide forward and 59" wide rearward compartmentation. Includes (2) 51.5" wide compartments over the wheel well.
Officer side body with upper and lower compartmentation. Includes 36" wide forward and 42" wide rearward lower compartments and (3) opening upper compartments.
Officer side body with 19.5" wide forward and 31" wide rearward compartmentation. Includes (1) 40" wide compartment over the wheel well.
Officer side body with full height 26" and 56" wide forward compartments and 56" wide rearward compartmentation. Includes (1) 56" wide compartment over the wheel well.
Stainless steel officer side body with full height 48" wide forward and 70" wide rearward enhanced extended compartmentation. Includes (1) 54" wide compartment over the wheel well.
PRICE
$14,756.00
$3,014.00
$6,921.00
$11,106.00
$1,592.00
$19,205.00
$1,599.00
$13,480.00
$5,157.00
$8,051.00
$10,004.00
$10,768.00
$11,094.00
$9,902.00
$14,885.00
$13,643.00
Option No.
3120‐0458
3120‐0460
3120‐0461
3120‐0462
3120‐0463
3120‐0464
3120‐0465
3120‐0466
3120‐0467
3120‐0468
3120‐0469
3120‐0470
3120‐0471
3120‐0472
3120‐0473
3120‐0474
Description
Officer high side stainless steel body with 60" front and 60" rear. Five compartments, tandem axle. For use with single arm overhead ladder rack.
Officer side tandem body with upper and lower compartmentation. Includes 30" wide forward and 54" wide rearward compartments and (4) opening upper compartments. Includes overhead rack opening centered between upper compartments. Includes offseting upper compartments forward due to deck gun location and access panel on upper rear compartment face to deck gun piping.
2‐arm ladder rack on officer side. The ladder rack includes Whelen 500 series TIR6 amber lights on each end to visually indicate when the rack is in motion. Restricts the top folding step (if optioned) from closing completely. Includes mounting bracket (if required, matching rear compartment face or compartment wrap finish) for components mounted on rear compartment face.
Officer side roof top compartment contents: (2) 6" x 10' hard suction hoses (not included) stored horizontally. Includes stop bracket rearward of hard suction hoses.
Officer side diamond plate roof top compartment. Includes vertical hinged access door at the rear with a "D‐Ring" latch handle to be wired to door ajar indicator in cab. .188 material
Stainless steel officer half side body with 36" wide front and 40" wide rear and 60" wide fender panel.
Officer side tandem body with full height (1) 60" wide forward and (1) 60" wide rearward compartmentation. For use with Rear Mount pump.
Officer side body with upper and lower compartmentation. Includes 36" wide forward and 36" wide rearward lower compartments and (3) opening upper compartments with (1) 33" wide compartment over the wheel well and (1) Zico Overhead Ladder Rack.
Stainless steel officer side body with full height 60" wide forward and 60" wide rearward compartmentation. Includes (1) 54" wide compartment over the wheel well.
Stainless steel officer side body with full height 48" wide forward and 58" wide rearward enhanced extended compartmentation. Includes (1) 60" wide compartment over the wheel well.
Stainless steel officer side body with full height 54" wide forward and 54" wide rearward compartmentation with custom size reduced upper depth. Includes (1) 54" wide compartment over the wheel well and (1) custom size storage tunnel.
Stainless steel officer side body with full height 48" wide forward and 54" wide rearward compartmentation. Includes (1) 54" wide compartment over the wheel well.
Officer side tandem body with (2) 34" wide forward and 54" wide rearward compartmentation. (1) forward compartment to be full height, (1) forward and rearward to be half height.
Officer 3/4 side body with full height 48" wide forward and 62" wide rearward enhanced extended compartmentation. Includes (1) 56" wide compartment over the wheel well and one (1) storage tunnel.
(2) officer side roof top compartments with removable floors and extra width to inboard side. Includes hinged raised compartment lids with turn latches, grab handle(s) and gas shock hold open and drain line(s) ran to below body. Each lid to have (1) bracket mounted LED light and to be wired to door ajar indicator in cab.
Rear aluminum smooth plated painted [#COL] vertically hinged door on officer side roof top compartments. Includes thumb latch and wiring for door ajar switch.
PRICE
$18,095.00
$14,756.00
$16,448.00
$1,088.00
$1,616.00
$5,613.00
$18,931.00
$17,276.00
$14,427.00
$13,166.00
$17,321.00
$12,690.00
$11,748.00
$15,126.00
$6,818.00
$220.00
Option No.
3120‐0475
3120‐0476
3120‐0477
3120‐0478
3120‐0479
3120‐0480
3120‐0481
3120‐0482
3120‐0483
3120‐0484
3120‐0485
3120‐0486
3120‐0487
3120‐0488
3120‐0489
3120‐0490
Description
Stainless steel officer side body with full height 60" wide forward and 60" wide rearward compartmentation. Includes (1) 54" wide compartment over the wheel well. Upper compartment depth only 12" IPO standard 14" due to 3‐section and roof ladders in tunnel.
Officer side body with full height 60" wide front and 54" wide rear compartments. Includes (1) 44" wide compartment over the wheel well and one (1) Zico overhead ladder rack. SS eMAX only.
(2) Officer side roof top compartments. Includes hinged raised aluminum smooth plate with black Scorpion coating (IPOS diamond plate) compartment lids with turn latches and grab handle(s). Each lid to have (1) bracket mounted LED light and to be wired to door ajar indicator in cab.
Officer side tandem body with 60" wide full height forward compartment. Rearward of the forward compartment to 3/4 height with 54" wide rearward compartmentation. Includes (2) 51.5" wide compartments over the wheel well.
Officer side body with full height/full depth 30/60" wide front and 54" wide rear compartments. Includes (1) 60" wide compartment over the wheel well. SS eMAX only.
Officer side body with full height 30/60" wide front and 54" wide rear compartments. Includes (1) 44" wide compartment over the wheel well, with Zico overhead ladder rack. SS eMAX only.
Officer side body with full height 30/60" wide front and 54" wide rear compartments. Includes (1) 60" wide compartment over the wheel well and one (1) storage tunnel located behind reduced upper depth compartments. SS eMAX only.
Officer side body with full height 50" wide forward and 42" wide rearward compartmentation. Includes (1) 33" wide compartment over the wheel well, (1) Zico overhead ladder rack. Rear perimeter or body raised 3" for improved departure angle.
Officer full height side body with upper and lower compartmentation. Includes 42" wide forward and 56" wide rearward lower enhanced compartmentation and (3) opening upper compartments. For use with ladder storage in the hosebed.
Officer side body with 19.5" wide forward and 31" wide rearward compartmentation. Includes (1) 40" wide compartment over the wheel well. Compartment tops raised approximately 6" to match hosebed height.
Stainless steel officer half side body with 30" wide front and 40" wide rear and 60" wide fender panel. For use with suicide hinged R1 door (if applicable).
Vertical and horizontal partitions located in officer side roof top compartment. Vertical partition located rearward of electric cord reel and horizontal partition located over DOT bottles. Floor to be provided above the DOT bottles to use remaining area above.
Officer side body with full height 48" wide forward and 56" wide rearward enhanced extended compartmentation. Includes (1) 56" wide compartment over the wheel well.
Vertical door stop for storage tunnel door.
Officer side roof top compartment contents: (1) 10' hard suction hose (not included) stored horizontal. Includes stop bracket rearward of hard suction hoses and Nylatron compartment flooring.
(2) officer side roof top compartments with extra width to inboard side. Includes hinged raised compartment lids with turn latches, grab handle(s) and gas shock hold open and drain line(s) ran to below body. Each lid to have (1) bracket mounted LED light and to be wired to door ajar indicator in cab. Compartment lid construction shall be aluminum smooth plate IPO diamond plate painted Black Scorpion (rough finish).
PRICE
$14,427.00
$25,002.00
$3,084.00
$12,600.00
$18,160.00
$26,707.00
$21,676.00
$19,205.00
$11,922.00
$10,465.00
$5,613.00
$1,307.00
$13,502.00
$127.00
$548.00
$5,881.00
Option No.
3120‐0491
3120‐0492
3120‐0493
3120‐0494
3120‐0495
3120‐0496
3120‐0497
3120‐0498
3120‐0499
3120‐0500
3120‐0501
3120‐0502
3120‐0503
3120‐0504
3120‐0505
3120‐0506
Description
Officer side body with upper and lower compartmentation. Includes 42" wide forward and 42" wide rearward lower compartments, (3) opening upper compartments. Includes (1) 33" wide compartment over the wheel well and (1) Zico Overhead Ladder Rack. Smooth plate compartment top painted black durabak.
Officer 3/4 side body with (3) full height, rescue style, (2) forward compartments (48" and 30" wide) and (1) rearward compartment (24"). Includes (1) 56" wide compartment over the wheel well.
Officer 3/4 side tandem stainless steel body with 35" front and 35" rear for flat back body design. Includes (2) 42" wide compartments over rear tandem wheels, with side dump valve between.
Officer side roof top compartment. Includes vertically hinged access door at the rear with push button latch to be wired to door ajar indicator in cab.
(2) officer side roof top compartments with extra width to inboard side. Includes hinged raised compartment lids with turn latches, grab handle(s) and gas shock hold open and drain line(s) ran to below body. Each lid to have (2) bracket mounted LED lights and to be wired to
door ajar indicator in cab.
Officer side tandem body with full height 30" wide forward and 30" wide rearward compartmentation. Includes (2) 42" wide compartments over the wheel well and overhead rack opening centered between upper compartments.
Officer side upper body extension. Stainless Steel product only. Does not include external upper doors. External platework only and painted FRP covering.
Stainless steel officer side body with full height 48" wide forward and 48" wide rearward compartmentation. Includes (1) 54" wide compartment over the wheel well.
Officer 1/2 side tandem stainless steel tanker body with 60" front and 60" rear for flat back body design. Includes (2) 55" wide tandem wheel fender panels.
Officer side body with full height 24" wide forward and 36" wide rearward compartmentation. Includes (1) 56" wide compartment over the wheel well. Rear bottom corner of truck will be angled 30 degrees for a greater rear angle of departure.
Officer side body with full height 36" wide forward and 62" wide rearward enhanced extended compartmentation. Includes (1) 56" wide compartment over the wheel well and one (1) storage tunnel.
Officer full height side body with 36" wide forward and 48" wide rearward compartmentation. Includes (2) 28.5" wide compartments over the wheel well for the installation of Zico Overhead Ladder Rack and one forward area for side tank dump. For use with custom chassis only.
Officer side tandem body with upper and lower compartmentation. Includes 30" wide forward full height and 30" wide low rearward compartments and (2) opening upper compartments. Includes offseting upper compartments forward due to deck gun location and access panel on upper rear compartment face to deck gun piping.
Officer side body with full height 48" wide forward and 48" wide rearward compartmentation. Includes (1) 33" wide compartment over the wheel well and (1) Zico Overhead Ladder Rack. Ladder rack controls to be located on officer side rear compartment face above tail lights. Compartment material to be 5083‐H321.
Officer 3/4 height side body with 42" wide and 20" wide forward compartments and 42" wide rearward compartment. Includes (1) 56" wide compartments over the wheel well. For use with custom chassis only.
Officer side body with full height 48" wide forward and 54" wide rearward compartmentation. Includes (1) 33" wide compartment (forward) over the wheel well and (1) Zico Overhead Ladder Rack.
PRICE
$18,847.00
$8,276.00
$12,333.00
$1,592.00
$5,562.00
$13,619.00
$1,376.00
$12,438.00
$14,031.00
$10,236.00
$15,116.00
$10,227.00
$14,158.00
$20,487.00
$8,231.00
$18,554.00
Option No.
3120‐0507
3120‐0508
3120‐0509
3120‐0510
3120‐0511
3120‐0512
3120‐0513
3120‐0514
3120‐0515
3120‐0516
3120‐0517
3120‐0518
3120‐0519
3120‐0520
3120‐0521
3120‐0522
3120‐0524
3120‐0525
3120‐0526
Description
Officer side body with full height 48" wide forward and 48" wide rearward compartmentation. Includes (1) 33" wide compartment (forward) over the wheel well and (1) Zico Overhead Ladder Rack.
Officer side ERV body with full height 37" forward and 52" rearward. Includes (1) 56" wide compartment over the wheel well. Includes (2) roof top compartments with hinged raised lids with thumb latches, grab handle(s), and gas shock hold open and drain line(s) ran to below body.Eack lid to have (1) bracket mounted LED light and to be wired to door ajar indicator in cab.
Officer side body with full height 24" wide forward and 36" wide rearward compartmentation. Includes (1) 56" wide compartment over the wheel well.
Officer half side body with 38" wide forward and 56" wide rearward compartment. Includes adjustable ladder tracks.
The rear body corner on the right side to extend full height and a smooth plate inner panel.
Notch compartment R2 in upper back wall rearward due to the 5" rear suction and provide a cover box.
(2) Officer side roof top compartments. Includes hinged raised compartment lids with thumb latches and grab handle(s). Each lid to have (1) bracket mounted LED light and to be wired to door ajar indicator in cab.
Officer half side tandem body with (2)41" wide forward and (2)32" wide rearward compartmentation.
Stainless steel officer side body with full height 48" wide forward and 54" wide rearward compartmentation with reduced upper depth. Includes (1) 60" wide compartment over the wheel well.
Stainless steel officer side body with half height 40" wide forward and 40" wide rearward compartmentation.
Stainless steel officer side body with full height 40" wide forward and 48" wide rearward compartmentation. Includes (1) 60" wide compartment over the wheel well.
Officer side body with 42" wide full height forward and 42" wide lower rearward lower compartments and (2) opening upper compartments. Includes offseting upper compartments forward due to deck gun location and and side facing access panels for deck gun piping.
Officer side roof top compartment contents: (1) 12'‐14'+ hard suction hose (not included) stored horizontal. Includes Nylatron compartment flooring. Length of capacity depends on body configuration.
Officer side body with full height 48" wide forward and 62" wide rearward compartmentation. Includes (1) 56" wide compartment over the wheel well.
Stainless steel officer side body with full height 48" wide forward and 58" wide rearward enhanced extended compartmentation. Includes (1) 60" wide compartment over the wheel well.
Officer 3/4 side body with full height 36" wide forward and 42" wide rearward compartmentation. Includes (1) 56" wide compartment over the wheel well.
Officer side body with full height 54" wide forward and 48" wide rearward compartmentation. Includes (1) 56" wide compartment over the wheel well.
(2) officer side roof top compartments with extra width to inboard side. Includes hinged raised compartment lids with turn latches, grab handle(s) and gas shock hold open and drain line(s) ran to below body. Each lid to be wired to door ajar indicator in cab.
(2) officer side roof top compartments. Includes hinged raised compartment lids with turn latches and grab handle(s). The rear compartment to include (1) vertically hinged access door at the rear with push button latch for access to (1) 6" X10' hard suction tube. Each lid to have (1) bracket mounted LED light and to be wired to door ajar indicator in cab.
PRICE
$18,329.00
$19,568.00
$10,236.00
$6,741.00
$198.00
$341.00
$2,735.00
$12,174.00
$12,248.00
$9,987.00
$11,773.00
$11,454.00
$638.00
$12,690.00
$12,912.00
$7,648.00
$12,636.00
$5,330.00
$2,834.00
Option No.
3120‐0527
3120‐0528
3120‐0529
3120‐0530
3120‐0531
3120‐0532
3120‐0533
3120‐0534
3120‐0535
3120‐0536
3120‐0537
3120‐0538
3120‐0539
3120‐0540
3120‐0541
3120‐0542
3120‐0543
Description
2‐arm ladder rack on officer side. Modified pivot position to allow the ladder rack to deploy at 48" to the center of ladders as loaded or less from ground level. The ladder rack includes amber lights on each end to visually indicate when the rack is in motion. Restricts the top folding step (if optioned) from closing completely. Includes mounting bracket (if required, matching rear compartment face or compartment wrap finish) for components mounted on rear compartment face.
Officer full height side body with 20" wide and 42" wide forward compartments and 42" wide rearward compartment. Includes (1) 56" wide compartments over the wheel well. For use with custom chassis only.
Officer side body with full height 42" wide forward and 56" wide rearward compartmentation. Includes (1) 56" wide compartment over the wheel well.
Officer high side stainless steel tanker body with 52" front and 52" rear rescue style, R2 and R3 modified for one‐arm Zico overhead ladder rack. Four compartments, tandem axle. Ladder rack not included, requires adding sales code 3365‐0185‐199.
Officer side body with full height, full depth 60" wide front and 54" wide rear compartments. Includes (1) 44" wide compartment over the wheel well and one (1) Zico overhead ladder rack. SS eMAX only.
Double hard suction storage rack: Two (2) hard suction hose storage racks shall be provided on the driver side of the body. The racks shall be positioned with one (1) rack located beside the other.
Stainless steel officer side special tall body with full height 40" wide forward and 58" wide rearward enhanced extended compartmentation. Includes (1) 54" wide compartment over the wheel well.
(2) officer side roof top compartments for use with Zico ladder lift. Includes hinged raised compartment lids with turn latches and grab handle(s). Each lid to have (1) bracket mounted LED light and to be wired to door ajar indicator in cab.
Officer side body with full height 60" wide forward and 62" wide rearward enhanced extended compartmentation. Includes (1) 33" wide compartment over the wheel well, one (1) storage tunnel and (1) Zico Overhead Ladder Rack.
Officer side body with full height 50" wide forward and 36" wide rearward compartmentation. Includes (1) 56" wide compartment over the wheel well. Rear perimeter or body raised 4" for improved departure angle.
Officer 3/4 side body with full height 42" wide forward and 54" wide rearward compartmentation. Includes (1) 56" wide compartment over the wheel well.
Officer half side stainless steel body with 40" wide forward and 58" wide rearward enhanced extended compartmentation. Includes adjustable ladder tracks, and 60" wide rear fender.
(2) officer side roof top compartments. Includes hinged raised compartment lids with slam style D‐ring latches and no grab handles. Each lid to have (1) bracket mounted LED light and to be wired to door ajar indicator in cab.
(2) officer side roof top compartments. Includes hinged raised compartment lids with turn latches and grab handle(s). Each lid to have (1) bracket mounted LED light and to be wired to door ajar indicator in cab. Includes fixed floor with hard suction storage below accessible through hinged rear panel access door with bent D‐ring latch.
Officer side body with full height 60" wide forward and 42" wide rearward compartmentation. Includes (1) 33" wide compartment over the wheel well and (1) Zico Overhead Ladder Rack.
Officer side body with full height 42" wide forward and 42" wide rearward compartmentation. Includes (1) 56" wide compartment over the wheel well.
Officer half side stainless steel body with 40" wide forward and 58" wide rearward extended compartmentation. Includes adjustable ladder tracks, and 60" wide rear fender.
PRICE
$13,064.00
$10,227.00
$13,251.00
$20,319.00
$25,216.00
$1,088.00
$12,690.00
$2,735.00
$24,754.00
$11,764.00
$7,361.00
$6,549.00
$2,866.00
$3,599.00
$18,788.00
$11,555.00
$6,606.00
Option No.
3120‐0544
3120‐0545
3120‐0546
3120‐0547
3120‐0548
3120‐0549
3120‐0550
3120‐0551
3120‐0552
3120‐0553
3120‐0554
3120‐0555
3120‐0556
3120‐0557
3120‐0558
3120‐0559
3120‐0560
3120‐0561
Description
Officer half side body with 42" wide forward and 50" wide rearward enhanced extended compartmentation. Includes adjustable ladder tracks.
Officer half side body with 24" wide forward and 50" wide rearward enhanced extended compartmentation.
Officer side smooth plate roof top compartment and painted black Durabak. Includes vertically hinged smooth plate access door painted job color at the rear with push button latch to be wired to door ajar indicator in cab.
(2) officer side roof top compartments with extra width to inboard side. Includes hinged raised compartment lids with turn latches, grab handle(s) and gas shock hold open and drain line(s) ran to below body. Each lid to have (1) Amdor strip LED light and to be wired to door ajar indicator in cab.
Officer full height side body with (3) full height, rescue style, forward compartments (48" and 30" wide) and (1) rearward compartment (24" wide), plus (1) upper compartment over w/well(33" wide and offset rearward of the rack opening).
Stainless steel officer side body with full height/full depth 34" wide forward and 48" wide rearward compartmentation. Includes 60" wide compartment over the wheel well.
Officer side tandem body with (1) 36" wide and (1) 20" wide forward and 54" wide rearward compartmentation. (1) forward compartment to be full height, (1) forward and rearward to be half height.
Stainless steel officer side body with full height 30" wide forward and 58" wide rearward enhanced extended compartmentation. Includes (1) 40" wide compartment over the wheel well and (1) Zico Overhead Ladder Rack.
Officer Full height forward compartment and 3/4 side rear of R1 tandem body with 42" wide forward and 42" wide rearward compartmentation. Includes (2) 51.5" wide compartments over the wheel well. Lowered W/Well for extra compt heigth. Side Dump Valves between Tandems N/A.
(2) officer side roof top compartments. Includes hinged raised compartment lids with turn latches and grab handle(s). Each lid to have (3) bracket mounted EION LED lightS and to be wired to door ajar indicator in cab.
Stainless steel officer half side body with 30" wide front and 40" wide rear and 60" wide fender panel.
Officer side tandem body with upper and lower compartmentation. Includes 60" wide full height forward and 54" wide half height rearward compartments and (1) opening forward upper compartment with painted panels rearward.
Officer side rear mount pumper body with full height 48" wide forward and 60" wide rearward compartmentation. Includes (1) 56" wide compartment over the wheel well and provisions to rear mount pump panel in rearward side compartment.
Officer side body with full height 60" wide forward and 48" wide rearward compartmentation. Includes (1) 56" wide compartment over the wheel well.
(2) officer side roof top compartments for instillation of DOT/ASME bottles. Includes hinged raised compartment lids with turn latches and grab handle(s). Each lid to have (1) bracket mounted LED light and to be wired to door ajar indicator in cab.
Officer side body with full height 42" wide forward and 42" wide rearward compartmentation. Includes (1) 56" wide compartment over the wheel well and one (1) storage tunnel beside the water tank.
Officer side body with full height 34" and 48" wide forward and 56" wide rearward compartmentation. Includes (1) 33" wide compartment over the wheel well and (1) Zico Overhead Ladder Rack.
Officer side body with full height 30" wide forward and 44" wide rearward compartmentation. Includes (1) 56" wide compartment over the wheel well.
PRICE
$6,253.00
$5,412.00
$1,990.00
$6,243.00
$9,731.00
$12,533.00
$9,914.00
$17,804.00
$14,398.00
$2,735.00
$5,353.00
$17,433.00
$12,964.00
$13,480.00
$2,735.00
$14,110.00
$22,427.00
$11,200.00
Option No.
3120‐0562
3120‐0563
3120‐0564
3120‐0565
3120‐0566
3120‐0567
3120‐0568
3120‐0569
3120‐0570
3120‐0571
3120‐0572
3120‐0573
3120‐0574
3120‐0575
3120‐0576
3120‐0577
3120‐0578
Description
Officer side body with full height 42" and 40" wide forward compartments and 56" wide rearward compartmentation. Includes (1) 56" wide compartment over the wheel well. Side Mount eMAX only.
Zico hydraulic drop‐down ladder rack (LAS‐XT) with 12 inches additional drop. Includes spacer brackets with ladder rack controller located on the officer side pump panel.
Stainless steel officer side body with full height/full depth 60" wide forward and 60" wide rearward compartmentation. Includes 60" wide compartment over the wheel well and a 2‐arm hydraulic overhead ladder rack.
Officer side body with full height 26" and 50" wide forward compts, 56" wide over wheel compt and 52" wide rearward compt. Includes slide‐back rear side compt for engine access and one (1) storage tunnel. eMAX HS only.
Stainless steel officer side body with full height 48" wide forward and 40" wide rearward compartmentation. Includes (1) 60" wide compartment over the wheel well.
Officer side body with full height 26" and 50" wide forward compts, 33" wide compartment over the wheel well, Zico Overhead Ladder Rack and 52" wide rearward compt. Includes slide‐back rear side compt for engine access. eMAX HS only.
Officer side rear mount rescue pumper body with full height 38" wide forward and 42" wide rearward compartmentation with officer side ladder storage tunnel. Includes (1) 56" wide compartment over the wheel well and 30 degree angled rear body for improved angle of departure.
Stainless steel officer side body with full height, full depth 48" wide forward and 40" wide rearward compartmentation. Includes (1) 54" wide compartment over the wheel well.
Officer full height body side with (1) 48" wide, Full Height forward compartment, (1) 30" wide, lower forward compartment adjacent to w/well, (2) upper compartments (57" wide each), the rearward upper having a rear compartment face access door for portable tank storage, and (1) lower rearward compartment (24") to rear of the w/well.
Stainless steel officer side body with full height 54" wide forward and 48" wide rearward compartmentation. Includes (1) 60" wide compartment over the wheel well.
Officer side body with full height 60" wide front and 54" wide rear compartments. Includes (1) 60" wide compartment over the wheel well and one (1) storage tunnel located behind reduced upper depth compartments. SS eMAX only.
(2) side low profile stepped interior roof top compartments with extra width to inboard side. Includes hinged raised compartment lids with turn latches,gas shock hold opens and drain line(s) ran to below body. Each lid to have (1) bracket mounted LED light and to be wired to door ajar indicator in cab. Lids shall be without grab handles for lowered OAH and shall have a stepped interior.
Officer half side body with 42" wide forward and 36" wide rearward compartmentation. Includes adjustable ladder tracks.
Stainless steel officer side body with full height 40" wide forward and 58" wide rearward enhanced extended compartmentation. Includes (1) 60" wide compartment over the wheel well.
Officer side rear mount rescue pumper body with full height 62" wide forward and 42" wide rearward compartmentation with officer side ladder storage tunnel. Includes (1) 56" wide compartment over the wheel well and 30 degree angled rear body for improved angle of departure.
Officer side rear mount rescue pumper body with full height 62" wide forward and 42" wide rearward compartmentation. Includes (1) 56" wide compartment over the wheel well and 30 degree angled rear body for improved angle of departure.
Officer side body with 3/4 height 36" wide forward and 56" wide rearward compartmentation. Includes (1) 56" wide x 20" high compartment over the wheel well.
PRICE
$15,421.00
$7,752.00
$15,125.00
$28,478.00
$12,272.00
$32,602.00
$15,596.00
$12,438.00
$11,663.00
$13,434.00
$20,005.00
$5,578.00
$5,377.00
$14,271.00
$17,656.00
$14,737.00
$8,658.00
Option No.
3120‐0579
3120‐0580
3120‐0581
3120‐0582
3120‐0583
3120‐0584
3120‐0585
3120‐0586
3120‐0587
3120‐0588
3120‐0589
3120‐0590
3120‐0591
3120‐0592
3120‐0593
3120‐0594
Description
Officer side diamond plate roof top compartment. Includes smooth plate painted vertical hinged access door at the rear with D‐Ring latch to be wired to door ajar indicator in cab. .125 material
(1) officer side roof top compartment. This is to be used for long handle tool storage and to be accessible through hinged rear panel access door with trigger style latch. Includes (1) bracket mounted LED light and to be wired to door ajar indicator in cab. Includes fixed forward wall at 143".
PRICE
Stainless steel officer half side body with 40" wide forward, 40" wide rear and a 60" wide fender panel. Includes adjustable ladder tracks.
Officer side body with full height, full depth 30/60" wide front and 54" wide rear compartments. Includes (1) 44" wide compartment over the wheel well, with Zico overhead ladder rack. SS eMAX only.
(1) shallow officer side roof top compartment with extra width to inboard side, forward position. Includes hinged raised compartment lid with turn latch, grab handle(s) and gas shock hold open and drain line(s) ran to below body. (1) rear opening hard suction storage compartment with lift up vertically hinged door w/bent D‐ring latch. Each compartment to have a (1) LED light and to be wired to door ajar indicator in cab. Compartments shorter to allow recessing of ladder rack.
$5,750.00
Officer half side body with 30" wide forward and 60" wide rearward extended compartmentation. Includes adjustable ladder tracks.
Stainless steel officer half side body with 30" wide front and 40" wide rear and 60" wide fender panel. For use with suicide hinged R1 door.
(2) officer side roof top compartments. Includes hinged raised compartment lids with turn latches and grab handle(s). Each lid to have (1) bracket mounted ROM V4 LED strip light and to be wired to door ajar indicator in cab.
Officer side body with full height 68" wide forward and 56" wide rearward compartmentation. Includes (1) 56" wide compartment over the wheel well and one (1) storage tunnel located behind the upper (3) compartment back walls.
Stainless steel officer side body with full height 60" wide forward and 60" wide rearward compartmentation with reduced upper depth. Includes (1) 60" wide compartment over the wheel well and (1) storage tunnel.
Officer full height side body with (3) full height, rescue style, forward compartments (48" and 30" wide) and (1) rearward compartment (24" wide), (1) upper compartment (56" wide).
Officer side rear mount rescue pumper body with full height 38" wide forward and 42" wide rearward compartmentation. Includes (1) 56" wide compartment over the wheel well and 30 degree angled rear body for improved angle of departure.
(2) officer side roof top compartments with extra width to inboard side. Compartment top and lids to be smooth plate painted black Durabak. Includes hinged raised compartment lids with turn latches, grab handle(s) and gas shock hold open and drain line(s) ran to below body. Each lid to have (1) bracket mounted LED light and to be wired to door ajar indicator in cab.
Stainless steel officer side body with full height 48" wide forward and 48" wide rearward compartmentation. Includes (1) 60" wide compartment over the wheel well, and a storage tunnel.
Electric Lock for Zico Hydraulic Drop Down Ladder Rack.
(2) officer side roof top compartments with extra width to inboard side. Includes hinged raised compartment lids with turn latches, grab handle(s) and gas shock hold open and drain line(s) ran to below body. Each lid to have (1) bracket mounted ROM V4 LED strip light and to be wired to door ajar indicator in cab.
$1,618.00
$3,003.00
$27,243.00
$5,712.00
$6,580.00
$5,365.00
$3,107.00
$16,972.00
$18,704.00
$9,731.00
$12,677.00
$6,831.00
$16,613.00
$2,138.00
$5,838.00
Option No.
3120‐0595
3120‐0596
3120‐0597
3120‐0598
3120‐0599
3120‐0600
3120‐0601
3120‐0602
3120‐0603
3120‐0604
3120‐0605
3120‐0606
3120‐0607
3120‐0608
3120‐0609
3120‐0610
Description
Officer side body with full height 30in. wide forward and 62in. wide rearward enhanced extended compartmentation. Includes (1) 56in. wide compartment over the wheel well and a cavity (using space from R1) between R1 and R2 for vertical exhaust to exit on outer compartment top just forward of wheel well.
Officer half side tandem body with 60" wide forward and 48" wide rearward compartmentation.
Officer side body with full height 60" wide forward and 56" wide rearward compartmentation. Includes (1) 56" wide compartment over the wheel well and one (1) storage tunnel located behind the upper (3) compartment back walls. Rear perimeter or body raised 3" for improved departure angle.
Officer side body with full height 30" wide forward and 50" wide rearward enhanced extended compartmentation. Includes (1) 33" wide compartment over the wheel well and (1) Zico Overhead Ladder Rack.
Officer full height side body with 20" wide and 42" wide forward compartments and 42" wide rearward compartment. Includes (1) 56" wide compartments over the wheel well. For use with 30" high lower compt height only.
Officer half side body with 44" wide forward and 36" wide rearward compartmentation and 28" high opening. Includes adjustable ladder tracks.
Officer side body with full height 30" wide forward and 50" wide rearward compartmentation. Includes (1) 33" wide compartment over the wheel well and (1) Zico Overhead Ladder Rack. Rescue Pumper individual style compartments.
Officer side body with full height 36" wide forward and 50" wide rearward compartmentation. Includes (1) 33" wide compartment over the wheel well and (1) Zico Overhead Ladder Rack. Rescue Pumper individual style compartments.
Officer half side tandem body with 66" wide forward and 40" wide rearward compartmentation. Includes 50" wide tandem wheel well compartment. SS top cap.
Stainless steel officer side body with full height 40" wide forward and 40" wide rearward compartmentation. Includes (1) 60" wide compartment over the wheel well.
Officer side body with upper and lower compartmentation. Includes 42" wide forward and 42" wide rearward lower compartments, (3) opening upper compartments. Includes (1) 33" wide compartment over the wheel well and (1) Zico Overhead Ladder Rack.
Officer side body with full height 60" wide forward and 56" wide rearward compartmentation. Includes (1) 56" wide compartment over the wheel well. Top Mount eMAX Only.
Officer 3/4 side tandem body with 3/4 full height 42" wide forward, (2) 51.5" wide compartments over the wheel well, and a 3/4 full height 42" wide rearward compartment. Additionally, there shall be a 3/4 full height 20" wide beavertail compartment openings.
Officer full height side body (FOR 4X4 Chassis) with 30" high lower compartment height, (2) lower forward compartments (34" and 28" wide) ahead of wheel well, (1) one lower rearward compartment 24" wide, and (3) upper compartments (48.67" wide x 32" high opening) each, transverse front to rear.
Stainless steel officer side body with full height 40" wide forward and 58" wide rearward enhanced extended compartmentation. Includes (1) 41" wide compartment over the wheel well and (1) Zico Overhead Ladder Rack.
Officer side body with full height 60" wide front and 54" wide rear compartments. Includes (1) 60" wide compartment over the wheel well for use with 2‐arm ladder rack. SS eMAX only.
PRICE
$15,734.00
$9,013.00
$16,399.00
$18,205.00
$10,227.00
$7,352.00
$18,205.00
$19,113.00
$10,657.00
$11,147.00
$17,905.00
$13,480.00
$10,490.00
$9,731.00
$19,204.00
$25,002.00
Option No.
3120‐0611
3120‐0612
3120‐0613
3120‐0614
3120‐0615
3120‐0616
3120‐0617
3120‐0618
3120‐0619
3120‐0620
3120‐0621
3120‐0622
3120‐0623
3120‐0624
3120‐0625
3120‐0626
3120‐0627
Description
(2) officer side roof top compartments. Includes hinged raised compartment lids with turn latches and grab handle(s). Each lid to have (1) Amdor LED strip light and to be wired to door ajar indicator in cab.
Officer side tandem body with upper and lower compartmentation. Includes 48" wide full height forward and 48" wide rearward compartments and (3) opening upper compartments. Includes offseting upper compartments forward due to deck gun location and access panel on upper rear compartment face to deck gun piping.
Officer 3/4 side stainless steel body with 40" wide forward and 58" wide rearward compartmentation. Includes (1) 60" wide compartment over the wheel well.
Officer side ERV style roof top compartment contents: (2) 6" x 10' hard suction hoses (not included) stored vertical. Includes vertical partition around hard suction hoses.
Officer side rear mount pumper body with full height 54" wide forward and 60" wide rearward compartmentation. Includes (1) 56" wide compartment over the wheel well and one (1) storage tunnel and access door at rear.
Officer side body with full height 60" wide forward and 52" wide rearward compartmentation. Includes (1) 33" wide compartment over the wheel well and (1) Zico Overhead Ladder Rack. Includes slide‐back rear side compt for engine access. HS only.
Stainless steel officer half side body with 35" wide front and 40" wide rear and 60" wide fender panel.
Officer side rear mount rescue pumper body with full height 24" wide forward and 42" wide rearward compartmentation. Includes (1) 56" wide compartment over the wheel well and 30 degree angled rear body for improved angle of departure.
Officer 3/4 side body with (2) lower forward compartments (48" and 30" wide), (3) upper compartments (55") and (1) lower rearward compartment (28").
Two (2) officer side roof top compartments with extra width to inboard side. Includes hinged raised compartment lids with one (1) L handle style 1/4 turn latche in the center of the compartment top, and two (2) grab handle(s) on each side of the L handle and gas shock hold open and drain line(s) ran to below body. Each lid to have (1) Amdor LED strip light and to be wired to door ajar indicator in cab.
Officer 3/4 side tandem body with full height 42" wide forward and 54" wide rearward compartmentation. Includes (2) 51.5" wide compartments over the wheel well.
Officer high side stainless steel body with 60" front and 60" rear. (4) compartments, tandem axle. For use with single arm overhead ladder rack.
Officer side tandem body with upper and lower compartmentation. Includes 60" wide lower forward and 54" wide lower rearward compartments and (1) forward upper compartment with standard hose bed side rearward.
Officer side body with full height 60" wide front and 54" wide rear compartments. Includes (1) 44" wide compartment over the wheel well and one (1) Zico overhead ladder rack. Ladder rack offset rearward. SS eMAX only.
Officer side body with upper and lower compartmentation. Includes full height 24" wide forward, 30" high by 38" wide lower rear, and 34" high by 38" wide upper rear compartmentation. Includes (1)33" wide compartment over the wheel well and (1) Zico Overhead Ladder Rack.
Stainless steel officer side body with full height 54" wide forward and 54" wide rearward compartmentation with reduced upper depth. Includes (1) 60" wide compartment over the wheel well and (1) storage tunnel.
Officer side body with full height 30" wide forward and 52" wide rearward enhanced extended compartmentation. Includes (1) 56" wide compartment over the wheel well.
PRICE
$3,513.00
$16,349.00
$8,105.00
$1,088.00
$22,681.00
$31,258.00
$5,562.00
$11,647.00
$7,954.00
$6,263.00
$10,570.00
$18,095.00
$17,433.00
$25,002.00
$16,457.00
$17,260.00
$11,200.00
Option No.
3120‐0628
3120‐0629
3120‐0630
3120‐0631
3120‐0632
3120‐0633
3120‐0634
3120‐0635
3120‐0636
3120‐0637
3120‐0638
3120‐0639
3120‐0640
3120‐0641
3120‐0642
3120‐0643
3120‐0644
3120‐0645
3120‐0646
Description
Officer half side body with (2) forward compartments (42" and 20" wide) and (1) rearward compartment (42"). The compartment opening height to be 30" IPO 34". For use with custom chassis only.
Officer side body with full height 60" wide forward compts, 56" wide over wheel compt and 52" wide rearward compt. Includes slide‐
back rear side compt for engine access and one (1) storage tunnel. HS only.
Stainless steel officer side body with full height 48" wide front and 58" rear with reduced upper depth for "T" tank. Includes 60" wide compartment over rear wheels. Upper compartments to be 15" deep.
(2) officer side roof top compartments for foam pails. Includes hinged compartment lids with turn latches and grab handle(s). Each compartment shall include LED lighting and to be wired to door ajar indicator in cab.
Stainless steel officer half side body with 48" wide front and 40" wide rear and 60" wide fender panel. Includes adjustable ladder tracks.
Stainless steel officer side body with full height/full depth 54" wide forward and 54" wide rearward compartmentation. Includes (1) 60" wide compartment over the wheel well.
Stainless steel officer 3/4 side body with full height 40" wide forward and 40" wide rearward compartmentation. Includes (1) 60" wide compartment over the wheel well.
Officer side rear mount pumper body with (2) two full height 34" wide forward and (1) one 60" wide rearward compartmentation. Includes (1) 56" wide compartment over the wheel well and one (1) storage tunnel and access door at rear.
Officer side tandem body with full height 60" wide forward and 54" wide rearward compartmentation. Includes (2) 51.5" wide compartments over the wheel well. Wheel wells and lower compartment height to lowered 4" over standard. (Pumper/Rescue Pumper Height).
Officer 1/2 side body with 24" wide forward and 42" wide rearward compartmentation. Includes adjustable ladder tracks.
Officer side body with full height 28" and 28" wide forward compts, 56" wide over wheel compt and 52" wide rearward compt. Includes slide‐back rear side compt for engine access and one (1) storage tunnel. HS only.
Officer side roof top compartment contents: (2) 6" x 10' hard suction hoses (not included) stored vertically. Includes horizontal partition between the hard suction hoses. NO stop for hoses.
Officer side rear mount pumper body with two full height 48" wide forward compartments and 42" wide rearward compartment. Includes (1) 56" wide compartment over the wheel well and 30 degree angled rear body for improved angle of departure.
Officer half side tandem body with 48" wide forward and 42" wide rearward compartmentation.
Officer side body with full height 30" wide forward and 50" wide rearward compartmentation. Includes (1) 56" wide compartment over the wheel well.
Officer half side stainless steel body with 30" wide forward and 58" wide rearward extended compartmentation. Includes adjustable ladder tracks and 60" wide rear fender.
Officer side body with full height 60in. wide forward and 42in. wide rearward compartments. Includes (1) 56in. wide compartment over the wheel well. Side Mount e‐MAX only.
Officer full height side body with 31" wide and 31" wide forward compartments and 42" wide rearward compartment. Includes (1) 56" wide compartments over the wheel well.
**NARROW BODY** Officer side body with full height 42" wide forward and 56" wide rearward enhanced extended compartmentation. Includes (1) 56" wide compartment over the wheel well and one (1) storage tunnel.
PRICE
$6,311.00
$27,139.00
$13,668.00
$2,735.00
$6,137.00
$16,758.00
$7,189.00
$19,084.00
$15,292.00
$5,504.00
$27,654.00
$1,088.00
$18,421.00
$9,013.00
$10,529.00
$6,606.00
$12,636.00
$10,227.00
$15,596.00
Option No.
3120‐0647
3120‐0648
3120‐0649
3120‐0650
3120‐0651
3120‐0652
3120‐0653
3120‐0654
3120‐0655
3120‐0656
3120‐0657
3120‐0658
3120‐0659
3120‐0660
3120‐0661
3120‐0662
Description
Rear aluminum smooth plate painted job color vertical hinged door on roof top compartment. Includes D‐ring latch and wiring for door ajar switch.
Roof top compartment contents: (1) 6in x 10ft hard suction hose (not included) stored in the lower area of roof top compartment. Includes stop bracket rear ward of hard suction hose if applicable to body length and partition surround over the hard suction hoses to accommodate storage area above and in front of the stored hose. Floor to include nylon pad as applicable for ease of deployment on scene.
**NARROW BODY** Officer side body with full height 36" wide forward and 36" wide rearward compartmentation. Includes (1) 33" wide compartment over the wheel well and (1) Zico Overhead Ladder Rack.
Stainless steel officer side body with full height 48" wide forward and 48" wide rearward compartmentation. Includes (1) 60" wide compartment over the wheel well.
Stainless steel officer side body with full height 48" wide forward and 54" wide rearward compartment with reduced upper depth. Includes (1) 60" wide compartment over the wheel well and (1) storage tunnel.
Officer side body with full height 30" and 60" wide forward compartments and 54" wide rearward compartmentation. Includes (1) 60" wide compartment over the wheel well. Side mount SS eMAX only.
Officer side body with special full height 23" wide forward and 50" wide rearward compartmentation. Includes (1) 50" wide compartment over the wheel well and (1) Zico Overhead Ladder Rack with special provision for ladder rack to be lowered so as to meet customer requirements in the down position.
Officer side diamond plate roof top compartment. Includes smooth plate painted vertical hinged access door at the rear with D‐ring style latch to be wired to door ajar indicator in cab.
Officer side rear mount rescue pumper body with full height 38" wide forward and 42" wide rearward compartmentation. Includes (1) 33" wide compartment over the wheel well, (1) Zico Overhead Ladder Rack, and 30 degree angled rear body for improved angle of departure.
Officer half side stainless steel body with 30" wide forward and 46" wide rearward compartmentation. Includes full height adjustable ladder tracks, and 60" wide fender panel.
Stainless steel 96" wide officer side body with full height 48" wide forward and 48" wide rearward compartmentation. Includes (1) 54" wide compartment over the wheel well.
The front body corner on the right side to extend full height and have a smooth plate inner panel.
**NARROW BODY** Officer side body with half height 36" wide forward and 36" wide rearward compartmentation. Includes adjustable ladder tracks mounted to the hosebed side wall.
Officer side body with full height 30" wide forward and 52" wide rearward enhanced extended compartmentation. Includes (1) 33" wide compartment over the wheel well and (1) Zico Overhead Ladder Rack.
Officer side tandem body with (2) full height 28" wide forward and 54" wide rearward compartmentation. Includes (2) 51.5" wide compartments over the wheel well.
Officer side body with 19.5in. wide forward and 31in. wide rearward compartmentation. Includes (1) 40in. wide compartment over the wheel well. Compartment tops raised approximately 6in. to match hosebed height. Rear of body under rearward compartment shall be raised 4in. or as applicable to allow for additional departure angle.
PRICE
$222.00
$701.00
$16,838.00
$12,566.00
$16,758.00
$18,160.00
$20,568.00
$1,592.00
$19,688.00
$5,724.00
$12,566.00
$198.00
$5,147.00
$17,559.00
$15,792.00
$10,671.00
Option No.
3120‐0663
3120‐0664
3120‐0665
3120‐0666
3120‐0667
3120‐0668
3120‐0669
3120‐0670
3120‐0671
3120‐0672
3120‐0673
3120‐0674
3120‐0675
3120‐0676
3120‐0677
3120‐0678
Description
Stainless steel officer side body with full height 36" wide forward and 48" wide rearward compartmentation. Includes (1) 60" wide compartment over the wheel well and a ladder storage tunnel.
Stainless steel officer side body with full height 44" wide forward and 60" wide rearward compartmentation. Includes (1) 54" wide compartment over the wheel well and ladder storage tunnel.
(3) Officer side roof top compartments with extra width to inboard side. (1) open generator compartment and (2) hinged raised compartments with lids and turn latches, grab handle(s) and gas shock hold open and drain line(s) ran to below body. Each lid to have (1) bracket mounted LED light and to be wired to door ajar indicator in cab.
Officer half side tandem body with 54" wide forward and 48" wide rearward compartmentation. Compartment height 30" pumper style. Side dumps not available.
Officer side body with full height 34" and 56" wide forward compartments and 56" wide rearward compartmentation. Includes (1) 56" wide compartment over the wheel well.
Stainless steel officer side body with full height, full depth 48" wide forward and 58" wide rearward enhanced extended compartmentation. Includes (1) 60" wide compartment over the wheel well.
Officer side tandem body with full height 48" wide forward and 48" wide rearward compartmentation. Includes (2) 51.5" wide compartments over the wheel well.
Officer half side stainless steel body with 30" wide forward and 46" wide rearward compartmentation. Includes full height adjustable ladder tracks, and 66" wide fender panel.
Officer side body with full height 60" wide forward and 46" wide rearward compartmentation. Includes (1) 56" wide compartment over the wheel well and one (1) storage tunnel located behind the upper (3) compartment back walls.
Officer side rear mount rescue pumper body with full height 24" wide forward and 42" wide rearward compartmentation with officer side ladder storage tunnel. Includes (1) 56" wide compartment over the wheel well and 30 degree angled rear body for improved angle of departure.
Stainless steel officer side body with full height 48" wide front and 48" rear compartments. Includes 60" wide compartment over the rear wheels.
Officer 3/4 side body with full height 60" wide forward and 42" wide rearward compartmentation. Includes (1) 56" wide and 20" high compartment over the wheel well.
Officer side tandem body with two forward compartments ahead of the rear wheels, and one rear compartment behind rear wheels. The forward front compartment to be 38" wide and full height, the rearward front compartment to be 24" wide and half height. The single rear to be a half height 60" wide compartment.
Stainless steel officer side body with half height 35" wide forward and 48" wide rearward compartmentation. Include 60" wide wheel well. Includes adjustable ladder tracks.
Officer side body with full height 36" wide forward and 56" wide rearward enhanced extended compartmentation. Includes (1) 56" wide compartment over the wheel well.
Officer side tandem body with upper and lower compartmentation. Includes 66" wide half height forward and 60" wide half height rearward compartments and (1) opening rearward upper compartment to rear of compartment top mounted Portable Tank or Equipment Storage.
PRICE
$13,140.00
$13,140.00
$5,728.00
$9,013.00
$15,499.00
$14,271.00
$14,500.00
$5,724.00
$15,797.00
$14,566.00
$12,633.00
$9,845.00
$15,292.00
$5,724.00
$11,535.00
$17,768.00
Option No.
3120‐0679
3120‐0680
Description
Officer 3/4 side body with upper and lower compartmentation. Includes 42" wide forward and 48" wide rearward lower compartments and (2) opening upper compartments.
Officer side body with full height 52" wide forward and 56" wide rearward compartmentation. Includes (1) 56" wide compartment over the wheel well and one (1) storage tunnel located behind the upper (3) compartment back walls.
3120‐0692
Two (2) officer side roof top compartments with extra width to inboard side. Includes hinged raised compartment lids with one (1) ' L' handle style 1/4 turn latch in the center of the compartment top, two (2) grab handle(s) on each side of the' L' handle, gas shock hold open and drain line(s) ran to below body. Each lid to have (1) Amdor LED strip light and to be wired to door ajar indicator in cab.
Officer side body with full height 35" wide forward and 47" wide rearward compartmentation. Includes (1) 56" wide compartment over the wheel well and one (1) storage tunnel.