SLP4-6D Single-mode Test Kit with Wave ID and Set Reference

SLP4-6D Single-mode Test Kit with Wave ID and Set Reference
SLP4-6D Single-mode Test Kit with Wave
ID and Set Reference
The SLP4-6D test kit combines the OPM4-4D optical power meter and OLS2-Dual LASER
light source and is ideally suited for testing single-mode fiber optic networks.
Features
•• Handheld, rugged, lightweight
•• Wave ID (auto identification & switching)
•• Dual or single Wave ID, CW, Tone
•• 270 Hz, 330 Hz, 1 kHz, 2 kHz Tone
•• Adjustable output
•• Large LCD with backlight (OPM4-4D)
•• Power measurements in dBm or μW;
insertion loss in dB
•• Reference power level storage
•• Low battery indicator
•• Long battery life with 2 x AA alkaline
•• Cost-effective, easy to use
•• N.I.S.T traceable
The OLS2-Dual features 1310 nm and 1550 nm LASER output from a single output port
and offers several modes of operation. Each wavelength may be transmitted individually
at CW or with user selectable modulated Tone. Also, each wavelength may be transmitted
with Wave ID. When transmitting with Wave ID, the OLS2-Dual supports transmitting pairs
of wavelengths in an alternating pattern. Associated with each operating condition, the
designated LED indicator will illuminate to identify the currently enabled operating mode
and emitted wavelength(s) along with battery charge status and external power presence.
The OLS2-Dual output port is equipped with a UCI based removable adapter to allow the
output connector to be inspected and cleaned.
The OPM4-4D features automatic wavelength identification and switching (Wave ID) when
used with the OLS2-Dual, multiple test Tone detection for fiber identification, and stores
optical references for each calibrated wavelength. A large dual-wavelength LCD display
with backlight shows measured power [dBm or µW] or insertion loss [dB], calibrated
wavelengths [nm], tone signal [Hz], wavelength ID, and estimated remaining battery life.
The OPM4-4D optical input port accepts a variety of Noyes thread-on style adapter caps
(ordered separately) to meet a wide range of testing requirements.
The OPM4-4D and OLS2-Dual offer long battery life from common AA alkaline batteries.
The SLP4-6D test kit is fully N.I.S.T. traceable.
Applications
•• Certify single-mode links per TIA/EIA standards
•• Fiber identification prior to splicing
Ordering Information
Model
Includes
SLP4-6D
OLS2-Dual optical light source, OPM4-4D optical power meter, AA batteries, protective rubber
boots, adapter cap, SLP4-6D test kit user's guide, and carry case.
Test jumpers and connector adapters are required for operation (purchased separately).
Test jumpers with a variety of connector styles and fiber types and adapter caps for most
common connectors may be purchased from AFL Telecommunications.
continued on the next page
© 2002-2009, AFL Telecommunications, all rights reserved. SLP4-30-2000 Revision D, 2009-06-16
Specifications are subject to change without notice.
1
SLP4-6D Single-mode Test Kit with Wave ID and Set Reference
OLS2-Dual specifications
Optical
OLS2-Dual (single port)
Wavelength
Emitter type
1310 ±20 nm
1550 ±20 nm
Laser, Class I FDA 21 CFR 1040.10 and 1040.11, IEC 60825-1: 2007-03
Spectral width (FWHM)
5 nm (max)
Output power
0 dBm*
Output stability
± 0.05 dB over 1 hour (after 15 min. warm-up)
± 0.1 dB over 8 hours (after 15 min. warm-up)
Tone output
General
270 Hz, 330 Hz, 1 kHz, 2 kHz
Power
2 x AA batteries, optional AC adapter
Battery life
Typical 120 hours, minimum 75 hours
Available adapters
SC FC, ST, LC
Operating temperature
-10 to 50°C, 90% RH (non-condensing)
Storage temperature
-30 to 60°C, 90% RH (non-condensing)
Size (H x W x D)
14.0 x 8.1 x 3.8 cm (5.5 x 3.2 x 1.5 in)
Weight
0.29 kg (0.65 lb)
* Adjustable 2 dB.
All specifications at 25°C.
OPM4-4D specifications
Optical
Calibrated wavelengths
OPM4-4D
850, 980, 1310, 1490, 1550, 1625 nm
Detector type
Filtered InGaAs
Measurement range
+26 to -50 dBm
Tone detect range
Wavelength ID range
Accuracy*
Resolution
Measurement units
General
Power
Battery life
+6 to -30 dBm
+6 to -25 for 850 nm
+6 to -30 dBm
+6 to -25 dBm for 850 nm
± 0.25 dB
0.01 dB
dB, dBm, μW
2 x AA batteries
300 hours
Operating temperature
-10 to 50°C, 90% RH (non-condensing)
Storage temperature
-30 to 60°C, 90% RH (non-condensing)
Size (H x W x D)
14.0 x 8.1 x 3.8 cm (5.5 x 3.2 x 1.5 in)
Weight
0.26 kg (0.58 lb)
* Accuracy measured at 25ºC and -10 dBm per N.I.S.T. standards.
All specifications at 25°C
© 2002-2009, AFL Telecommunications, all rights reserved. SLP4-30-2000 Revision D, 2009-06-16
Specifications are subject to change without notice.
2
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement