IET LABS PRS-300 Programmable Decade Resistance Substituter Operation Manual

Below you will find brief information for Programmable Decade Resistance Substituter PRS-300 PRS-300. The PRS-300 is a high precision manual and programmable decade substituter. It provides direct resistance substitution as well as RTD (Resistance Temperature Detector) simulation. It offers a wide choice of ranges, power, voltage, and accuracies for a wide variety of design and production applications.

PDF Download

Document

♦

PRECISION INSTRUMENTS FOR TEST AND MEASUREMENT

♦

PRS-300 SERIES

Programmable

Decade Resistance Substituters

(IEEE-488.2, Ethernet and USB)

Operation Manual

IET LABS, INC.

www.ietlabs.com

TEL: (516) 334-5959 • (800) 899-8438 • FAX: (516) 334-5988

IET LABS, INC.

www.ietlabs.com

TEL: (516) 334-5959 • (800) 899-8438 • FAX: (516) 334-5988

♦

PRECISION INSTRUMENTS FOR TEST AND MEASUREMENT

♦

PRS-300 SERIES

Programmable

Decade Resistance Substituters

(IEEE-488.2, Ethernet and USB)

Operation Manual

Copyright

©

2016 IET Labs, Inc.

PRS-300 IM / October 2016

IET LABS, INC.

www.ietlabs.com

TEL: (516) 334-5959 • (800) 899-8438 • FAX: (516) 334-5988

♦

PRECISION INSTRUMENTS FOR TEST AND MEASUREMENT

♦

IET LABS, INC.

www.ietlabs.com

Email: [email protected]

TEL: (516) 334-5959 • FAX: (516) 334-5988

PRS-300 Series

WARRANTY

We warrant that this product is free from defects in material and workmanship and, when properly used, will perform in accordance with applicable IET speci fi cations. If within one year after original shipment, it is found not to meet this standard, it will be repaired or, at the option of IET, replaced at no charge when returned to IET. Changes in this product not approved by IET or application of voltages or currents greater than those allowed by the speci fi cations shall void this warranty. IET shall not be liable for any indirect, special, or consequential damages, even if notice has been given to the possibility of such damages.

THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESSED OR IMPLIED,

INCLUDING BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR

FITNESS FOR ANY PARTICULAR PURPOSE.

PRS-300 Series

WARNING

OBSERVE ALL SAFETY RULES

WHEN WORKING WITH HIGH VOLTAGES OR LINE VOLTAGES.

Dangerous voltages may be present inside this instrument. Do not open the case

Refer servicing to quali

ed personnel

HIGH VOLTAGES MAY BE PRESENT AT THE TERMINALS OF THIS INSTRUMENT

WHENEVER HAZARDOUS VOLTAGES (> 45 V) ARE USED, TAKE ALL MEASURES TO

AVOID ACCIDENTAL CONTACT WITH ANY LIVE COMPONENTS.

USE MAXIMUM INSULATION AND MINIMIZE THE USE OF BARE

CONDUCTORS WHEN USING THIS INSTRUMENT.

Use extreme caution when working with bare conductors or bus bars.

WHEN WORKING WITH HIGH VOLTAGES, POST WARNING SIGNS AND

KEEP UNREQUIRED PERSONNEL SAFELY AWAY.

CAUTION

DO NOT APPLY ANY VOLTAGES OR CURRENTS TO THE TERMINALS OF THIS

INSTRUMENT IN EXCESS OF THE MAXIMUM LIMITS INDICATED ON

THE FRONT PANEL OR THE OPERATING GUIDE LABEL.

WARRANTY ........................................................................................................... i

WARNING ............................................................................................................. ii

CAUTION .............................................................................................................. ii

CONTENTS .......................................................................................................... iii

FIGURES .............................................................................................................. iv

TABLES ............................................................................................................... iv

Chapter 1: INTRODUCTION ................................................................................ 1

Chapter 2: SPECIFICATIONS .............................................................................. 3

2.1 Model Con fi guration and Speci fi cations ........................................................................3

2.2 General Speci fi cations ...................................................................................................4

2.2 Operating Guide .............................................................................................................5

Chapter 3: OPERATION ....................................................................................... 6

3.1 Initial inspection and setup ............................................................................................6

3.2 Connection .....................................................................................................................6

3.2.1 General Considerations ........................................................................................6

3.2.2 Electrical Considerations ......................................................................................6

3.3 Condensed Operating Instructions .................................................................................6

3.4 Menu Structure ...............................................................................................................7

3.4.1 Main Menu ...........................................................................................................8

3.4.2 Setting a Resistance Value ....................................................................................8

3.4.3 Menu Button .........................................................................................................8

3.4.4 Standard Values Screen ........................................................................................8

3.4.6 Increment INCR Key ............................................................................................9

3.4.7 OPEN Key ............................................................................................................9

3.4.8 STO,RCL Keys ...................................................................................................10

3.4.10 2 and 4 Wire Connections ................................................................................10

3.4.11 Thermal emf Considerations ............................................................................10

3.4.12 Environmental Conditions ................................................................................11

3.4.13 Remote Operation .............................................................................................11

Chapter 4: USB Interface .................................................................................. 12

4.1 Introduction ..................................................................................................................12

4.2 Capabilities ..................................................................................................................12

4.3 USB Operation .............................................................................................................12

PRS-300 Series

Table of Contents iii

PRS-300 Series

Chapter 5: ETHERNET INTERFACE OPTION ................................................... 14

5.1 Ethernet Programming .................................................................................................14

5.2 Network Setup .............................................................................................................14

5.3 Ethernet Test Keyboard ................................................................................................14

5.4 Network Con fi guration ................................................................................................15

5.5 Web Browser Con fi guration .........................................................................................15

5.6 VXI Con fi guration Utility ............................................................................................17

5.7 Resetting Default Network Settings .............................................................................19

5.8 PRS Programming .......................................................................................................19

Chapter 6: IEEE INTERFACE OPTION .............................................................. 20

6.1 Introduction ..................................................................................................................20

6.2 Capabilities ..................................................................................................................20

6.3 Address Switch and Communications Settings ............................................................20

6.4 IEEE Option Operation ................................................................................................20

Chapter 7: PROGRAMMING ................................................................... 22

7.1 Introduction

......................................................................................... 22

Chapter 8: MAINTENANCE .................................................................... 23

8.1 Veri fi cation of Performance

.................................................................... 23

8.1.1 Calibration Interval

........................................................................ 23

8.1.2 General Considerations

.................................................................. 23

8.1.3 Calibration Procedure

.................................................................... 23

8.1.4 Adjustment of Internal Resistors

..................................................... 23

APPENDIX A: SCPI COMMAND REFERENCE ...................................... 25

APPENDIX B: IEEE.2 COMMON COMMANDS ...................................... 29

Table of Contents

PRS-300 Series

Chapter 1 INTRODUCTION

The PRS-300 (Figure 1.1) is a high precision manual and programmable decade substituter. The PRS-300 series provide direct resistance substitution as well as RTD (Resistance Temperature Detector) simulation.

The PRS-300 substituter is a precision resistance source with excellent characteristics of stability, temperature coef fi cient, and power coef fi cient. These features combined with a low virtually constant “zero resistance” make for very versatile instruments.

Operation is both local using convenient display and keypad and remote standard USB or optional Ethernet, and IEEE-488.2 interfaces. An RS-232 interface is also available upon request.

The PRS-300 employs very low resistance, low thermal emf relays with gold-clad silver-alloy contacts. A special design keeps contact resistance to a minimum. The gold plating keeps the silver contacts from becoming tarnished when unused, or when only low currents are passed through them. This is most often the case when only minute test currents are drawn by digital multimeters and other test instruments. Contact resistance remains low and repeatable.

High-quality gold-plated tellurium-copper fi ve-way binding posts serve to minimize the thermal emf effects, which would produce errors in dc resistance measurements.

With a resolution as low as 1 μ

and a maximum available resistance of 20 M

, the

PRS-300 may be used for exacting precision measurement applications requiring high accuracy, good stability, and low zero resistance.

The PRS-300 is suited for automatic and manual calibration and testing, simulation of

RTD’s, programmable loads, and many other laboratory and industrial applications.

The PRS Series may be rack mounted to serve as components in measurement and control systems.

The PRS-300 (Figure 1.1) is part of the

PRS family of high precision manual and programmable decade substituters. This series

Figure 1.1: High Precision Programmable Decade

Resistance Substituter

INTRODUCTION

PRS-300 Series

offers a wide choice of ranges, power, voltage, and accuracies for a wide variety of design and production applications.

The PRS-300 uses a microcontroller design to enhance the ease of use and calibration. It provides direct resistance substitution as well as RTD (Resistance Temperature Detector) simulation. It allows for higher precision and tighter tolerances.

The PRS-300 is a precision resistance source with excellent characteristics of accuracy, stability, temperature coef fi cient, and power coeffi cient. It is direct reading without the need to subtract “zero resistance.”

The PRS-300 offers the option of true 4-wire

Kelvin measurement for calibration applications and 2-wire mode for use in series as a substitute resistor and for RTD applications.

The front panel display indicates the mode selected: 2-wire or 4-wire.

There are two pre-programmed RTD resistance tables, and others may be added by the user.

The controller allows for other convenient programmed features.

The unique design makes adjustment of the

PRS-300 for calibration semiautomatic. An internal calibration routine guides the user to perform measurements using

only

a precision ohmmeter and enter the measured values into the PRS-300. No other standards are required.

IET Labs offers the PRS-DMM software which works with the PRS-300 and Fluke

8508A or Keysight 3458A to automate this adjustment process and eliminate the need for a technician to manual enter the resistance values manually into the PRS-300

INTRODUCTION

PRS-300 Series

Chapter 2 SPECIFICATIONS

For convenience to the user, the pertinent speci fi cations are given in an OPERATING

GUIDE, shown typically in Figure 2.1, af fi xed to the case of the instrument.

2.1 Specifi cations

User interface:

Numeric keypad to enter resistance value with digital display.

Accuracy:

±(70 ppm + 1 m Ω ) 2 and 4 Terminal

Minimum setting:

0.1 Ω

Resolution:

1 μΩ or 6 digits

Range:

0.1 Ω - 20 M Ω

Stability:

50 ppm/year

Thermal emf:

< 15 μ V

Maximum Load:

2 A, 200 V (peak), 0.5 W whichever applies fi rst

Resistors:

Precision wire-wound and metal foil

RTD Tables:

9 RTD tables can be entered into memory to allow user selection of temperature and the correct value of resistance will automatically be programmed.

PT-100 and PT-1000 tables for both Fahrenheit and

Celsius are pre-programmed into memory locations

1 to 4.

Adjustment:

Automatic adjustment procedure utilizing a high precision DMM eliminates the requirement for manual trimming of resistors.

AC Frequency Response:

Residual Capacitance Terminals to GND: < 850 pF

Resistance

0.1 Ω -10 k Ω

10 - 100 k Ω

100 k Ω - 1 M Ω

Typical ac/dc difference @ 1 kHz

<100 ppm

<200 ppm

<1%

1 - 20 M Ω <20%

Terminals

Four low-emf, gold-plated, tellurium-cop per 5-way bind ing posts are used for

and

ter mi nal pairs for

CUR RENT

and

SENSE

GND

bind ing post is con nect ed to the case, to the chassis ground and to the earth ground.

Switching time:

<1 second per change

Power requirements:

90 - 264 Vac , 47 - 63 Hz. 30 Watts Max.

Dimensions:

Bench model: 43 cm W x 8.9 cm H x 33 cm D (17” x

3.5” x 13”)

in front of panel

: 3.8 cm (1.5”).

Weight:

Bench model: 5.5 kg (12 lb); weight speci fi cations are nominal.

Remote Control:

USB:

USB Type B connector standard on rear panel

Remote Control Options:

IEEE:

GPIB standard 24 pin connector, conforms to IEEE-

488.2; SCPI 1994.0 command set; Hardware or software con fi gurable addressing range of 1 to 30.

Ethernet:

IEEE 802.3 compliant, Speeds 10 BaseT

(10 Mb/s) and 100 BaseT (100 Mb/s), IP Address

Static or DHCP, Factory setting 192.168.0.254 static

SPECIFICATIONS

PRS-300 Series

2.2 General Specifi cations

Warmup:

This unit utilizes custom designed low thermal emf relays for high stability and low-level signal applications. This thermal voltage is nominally less than 10

V under laboratory conditions. Please note that a change in this thermal emf will give a false drift in resistance as measured by a dc ohmmeter, since the ohmmeter will interpret this emf as an effective resistance.

The worst case such effective drift after warm-up is less than ±50 ppm, primarily due to stabilization of this emf at the relay contacts as settings are changed.

Unit should be allowed to stabilize for one hour. For maximum stability, allow unit to warm-up over two hours.

Recommended Calibration Interval:

12 months.

4 SPECIFICATIONS

PRS-300 Series

PRS-300 PROGRAMMABLE DECADE RESISTANCE SUBSTITUTER

CONSULT INSTRUCTION MANUAL FOR PROPER INSTRUMENT OPERATION

Accuracy:

±(70 ppm + 1 m Ω ) 4 Terminal

Switching time:

<1 second per change

Minimum setting:

0.1 Ω

Power requirements:

Resolution:

1 μΩ

90 - 264 Vac , 47 - 63 Hz. 30 Watts Max.

Range:

0.1 Ω - 20 M Ω

Stability: ±

50 ppm/year

Thermal emf:

< 15 μ V

Dimensions:

Bench model: 43 cm W x 8.9 cm H x 33 cm D (17" x 3.5" x 13")

in front of panel

3.8 cm (1.5").

Weight:

Bench model: 5.5 kg (12 lb) weight speci fi cations are nominal.

Maximum Load:

2 A, 200 V (peak), 0.5 W whichever applies fi rst

Resistors:

Precision wire-wound and metal foil

Remote Control:

RTD Tables:

USB:

Standard USB Type B connector on rear panel, uses FTDI driver

3 RTD tables can be entered into memory to allow user selection of temperature and the correct value of resistance will automatically be programmed. PT-100 and PT-1000 tables are pre-programmed into memory.

Remote Control Options:

IEEE:

GPIB standard 24 pin connector, conforms to IEEE-488.2; SCPI 1994.0 command set; Hardware or software con fi gurable addressing range of 1 to 30.

Adjustment:

Automatic adjustment procedure utilizing a high precision DMM eliminates the requirement for manual trimming of resistors.

E t h e r n e t :

I E E E 8 0 2 . 3 c o m p l i a n t , S p e e d s 1 0 B a s e T

(10 Mb/s) and 100 BaseT (100 Mb/s), IP Address Static or DHCP, Factory setting

192.168.0.254 static

Terminals

Four low-emf, gold-plated, tellurium-cop per 5-way bind ing posts are used for

and

ter mi nal pairs for

CUR RENT

and

SENSE

GND

bind ing post is con-

nect ed to the case, to the chassis ground and to the earth ground.

MODEL: PRS-300 SN: E1-1634626

WARNING

Observe all safety rules when working with high voltages or line voltages. Connect the (GND) terminal to earth ground in order to maintain the case at a safe voltage.

Whenever hazardous voltages (>45 V) are used, take all measures to avoid accidental contact with any live components: a) Use maximum insulation and minimize the use of bare conductors. b) Remove power when adjusting switches. c) Post warning signs and keep personnel safely away.

IET LABS, INC.

CAGE CODE: 62015

• Long Island, New York

• Tel: (516) 334-5959 • Email: [email protected]

www.ietlabs.com

PRS-300 Nov. 2016

FIGURE 2.1 Typical OPERATING GUIDE Af fi xed to Unit

(Please see label af fi xed to your unit)

SPECIFICATIONS

PRS-300 Series

Chapter 3 OPERATION

3.1 Initial inspection and setup

This instrument was tested and carefully inspected before shipment. It should be in proper electrical and mechanical order upon receipt.

OPERATING GUIDE

is attached to the case of the instrument to provide ready reference to speci fi cations.

Mount the unit in a standard 19” rack if the rack mount option is speci fi ed.

3.2 Connection

3.2.1 General Considerations

The PRS-300 Decade Resistor utilizes a

5-terminal connection. The binding posts are standard laboratory type and readily accept banana plugs, spade lugs, alligator clips, and bare wire. Binding posts are located on the front panel of the instrument unless speci fi cally ordered with a Rear Output option.

The Kelvin terminals consisting of a

CURRENT

and a

SENSE

pair, each labeled

HI

and

LO

. These minimize contact resistance.

The

GND

terminal on all models is connected to the case and to earth and chassis grounds. This may be used as a shield terminal.

3.2.2 Electrical Considerations

The performance of the PRS-300 is directly affected by the quality of the connection to the system under test. This is particularly true with the precision series models having higheraccuracy and/or lower-impedance decades.

For optimum performance, contact resistance should be kept to a minimum by using the most substantial mating connection possible, and by assuring that the connection is well secured to the binding posts.

3.3 Condensed Operating Instructions

1. Turn on the PRS-300 ON using POWER

SWITCH

2. Select a desired resistance value in one of the following ways: a) Enter a value using the number keys, b) Press a Quick Value key (

A

– B) to c) Press

3. then press

ENTER

display a user-de fi ned value or a factory default value.

Default values are: k Ω

then a number key ( to display a user-de tory default value.

Default values are: k Ω │

2

- 2 k Ω

A

0

: 10 k

- 100

│

B

0 – 9

1

: 100

- 1

To prevent possible damage to the PRS-300, set the maximum

)

ned value or a fac-

OPERATION

PRS-300 Series

applied voltage by pressing

VOLT

, entering the voltage on the keypad, then pressing

ENTER

. (Default: 0.5 V)

The fi rmware sets the minimum selectable resistance value so that the power does not exceed 1 W. To ensure that the whole range of resistances is selectable,

VOLT

setting must be ≤ 1 V.

Rmin is limited to >V

, where V is the

VOLT setting.

4. Select 2-wire or 4-wire mode by pressing the

CON-

FIGURE

, pressing the “2” will change between 2-wire and 4-wire modes

In 2-wire mode shorting links must be installed across high and low terminal pairs.

In 4-wire remove the shorting links.

5. Connect to the circuit or device under test.

To isolate the PRS-300 from the application, press

OPEN

to open the circuit. To close the circuit, press

OPEN

again.

3.4 Menu Structure

The main table below show menu structure of the PRS-300 and basic function of each button and menu selection.

Key Description Function

Basic operation enter

enter button Sets resistance value

0-9, 000/(-)

Used to enter numerical values. To select desired numerical value, press value as required.

(-)

is used with tables for negative temperature

◄

Deletes the last character from the display.

To delete the last character, press

◄

Options

MENU

INCR

Displays the following submenu:

1. STANDARD VALUES

1: 1% STD VALUES

2: 5% STD VALUES

3: 10% STD VALUES

4: RATIOMETRIC

2. CONFIGURE

1: LCD CONTRAST

2: 2W / 4W MODE

3. CALIBRATE

4. VERSION

Press

MENU

to select one of the following:

1. STANDARD VALUES - selects increments for UP and DOWN keys

2. CONFIGURE - allows user to adjust display contrast and change between 2-wire and 4-wire modes

3. CALIBRATE - see Section 8

4. VERSION - Displays current fi rmware version and release date.

Selects the increments for the

UP and DOWN keys

Default value: Ratiometric (0.8% of displayed value)

To adjust increments:

1. Press .

2. Enter desired increment value on the keypad.

3. Press to save.

Storing and recalling resistance values

STO

Stores a resistance value in memory locations A-D and 0-9.

To store a value, press

STO

and then press the desired location button A-D or 0-9.

A, B

RCL

Recalls a stored resistance value.

Default values:

: 10 k Ω

: 100 k Ω

Recalls a stored resistance value from memory location 0-9.

To change stored values:

1. Enter a resistance value

2. Press and then

To recall a stored value, press

RCL

, then press the desired location button (0-9)

Limiting Current

VOLT

Sets voltage to limit the current in order to protect the PRS-300 from possible damage.

Default value: 0.5 V

To adjust voltage:

1. Press .

2. Enter desired voltage on the keypad.

ENTER

to save.

Electrical Isolation

OPEN

Isolates the connection terminals To open the circuit, press

OPEN

by establishing an open circuit.

To close, press

OPEN

again.

Option: Simulating RTD’s and transducers

TABLE

Loads up to 9 stored data tables for simulating RTD’s or transducers.

To select the desired table, press

TABLE

to cycle through the three options.

OPERATION 7

PRS-300 Series

3.4.1 Main Display

The main display shows the resistance value in ohms or temperature value if tables are used. The main display also shows if the unit is con fi gured for

4W

(4-wire mode) or

2W

(2-wire mode) in the upper left corner of the display.

3.4.4 Standard Values Screen

There are 4 selections available in the

STNADARD VALUES

menu. The operation of the standard values allows the PRS-300 to be used as an automated resistance carousel with built-in EIA “preferred value” resistance tables of 1% (E96), 5% (E24), 10% (E12) increments or RATIOMETRIC user speci fi ed increment.

Figure 3-1 Main Display showing 4-Wire

See section 3.2.3 for more information on

2-wire and 4-wire connections.

3.4.2 Setting a Resistance Value

To set a resistance value use the numeric keypad to enter the value followed by the

ENTER

button. The

000

button can be used to increase the resistance value by a factor of

1000.

The

UP

and

DOWN

keys can also be used to increment or decrement the resistance value. See 3.4.6

INCR

Key for more information.

3.4.3 Menu Button

Pressing the

STANDARD VALUE

is selected on the PRS-300 pressing the

UP

DOWN

arrows will increment the resistance value to the

OPERATION

PRS-300 Series

next “preferred” resistance value.

RATIOMETRIC allows a custom tolerance value to be entered by the user. The default value is 0.8% but can be set to the required value in %. heit.

TABLE

key allows use of tables. There are 9 tables that can be selected.

The fi

3.4.5 Tables Key

Pressing the

rst 4 tables, 1 to 4, are de

C, PT-100 F, PT-1000 C and PT-1000 F where

C is degrees Celcius and F is degrees Fahren-

Press

TABLE

table as shown in Figure 3-5 fi ned as PT-100

key and then a number key

0 through 9 followed by the select a table. Table 0 is de fi used and resistance is shown.

ENTER

Figure 3-4 No translation Table

key will

ned as no table is

Press the numerical value 1 to 9 on the keypad for the desired table to be used. For example pressing

TABLE

key, then “1” and

ENTER

key will select use of the PT-100 C

Figure 3-5 Table 1 PT-100 C

Once the table is selected the display will change showing temperature on top and resistance on bottom. Any value entered via front panel or remotely will be assumed to be a table value rather than a resistance value. For example if 0.25 is entered then the screen will look like Figure 3-5 showing temperature on top line and resistance on the bottom line.

Figure 3-5 PR-100 C set to 0.25 °C

For negative temperatures press the 000/

(-) key prior to entering the value.

If a value is not listed in the table and is entered using the numeric keypad or selected using the

UP

and

DOWN

keys interpolation is used between the two closest table values.

Custom tables can be entered in locations

5 to 9 by using the USB interface and remote

CONIG:TABLE

commands. See Appendix B for more information.

3.4.6 Increment INCR Key

The

INCR

key allows entry of a numeric value. The numeric value representing the step or increment size the

UP

and

DOWN

keys use.

For example pressing

INCR

key and then

10 would result in the displayed value being incremented or decremented 10 Ω for each time the

UP

DOWN

key is pressed.

INCR

can also be used for tables in the same way so that the operator can press the

UP

DOWN

key and increment or decrement the displayed value in °C or °F.

3.4.7 OPEN Key

The

OPEN

key opens all relays in the

PRS-300 resulting in high resistance at the resistance terminals. The display will shown

OPEN

. Pressing the

OPEN

key again will cause the resistance to return to the previous set value.

For short enter lowest value of 0.1 Ω us-

OPERATION

PRS-300 Series

ing keypad or remote.

3.4.8 STO, RCL Keys

The

STO

and

RCL

key are used to store user de fi ned values into memory. Press

STO

key followed by 0 to 9 in the numeric keypad stores the currently shown resistance value into that memory location.

Press

RCL

key followed by 0 to 9 in the numeric keypad recalls the resistance value saved into memory to the currently displayed value.

3.4.9 VOLT Key

The

VOLT

key should normally be set to 0.5 V which allows us of the full resistance range of the PRS-300. Pressing the

VOLT

key followed by a numeric value representing the maximum voltage being used in the applicaton will limit the lowest resistance that can be entered to prevent damage to the PRS-300.

The limited is based upon a maximum of

1 W being applied to the resistors. Note that

0.5 W is the maximum recommended and operation at 1 W can cause the internal resistors to drift beyond speci fi cation.

3.4.10 2 and 4 Wire Kelvin Lead Connections

2-wire

4-wire

operation can be selected from by pressing the

CONFIGURE

, pressing the “2” will change between 2-wire and 4-wire modes.

The use of 4W with Kelvin leads minimize the effects of contact resistance and gives best performance. In 4-wire remove the shorting links from the high and low terminal pairs.

Figure 3-6 4-Terminal shorting links not connected

2W mode should be used when connecting to a 2 wire device or if the PRS-300 will be used as a standard 2-terminal resistor such as

RTD simulation. In 2-wire mode shorting links must be installed across high and low terminal pairs.

Figure 3-7 Two terminal with shorting links

3.4.11 Thermal emf Considerations

The PRS Series uses high-quality, lowemf components. Thermal emf is primarily attributable to the temperature difference between the leads of the relay and the contacts when temperature is applied to the coil. This emf is of the order of 5 μ V per relay, but is not usually additive. The typical worst case is <15

If the effect of tens of microvolts is signi fi cant to your application, connect to the instrument with low-thermal-emf materials only. Copper wire and copper alloys are recommended; brass and steel should be avoided.

Tinned copper and solder are acceptable.

OPERATION

PRS-300 Series

This emf will

not

be re fl ected if an ac measurement instrument is employed, and can be eliminated by using a meter with “True

Ohm” capability. In other cases, the emf may represent a very small component of a dc resistance measurement.

3.5 Environmental Conditions

The PRS is built, calibrated and intended for use in a laboratory environment with a nominal ambient temperature near 23 o

C. The accuracy of the unit may be affected when operated in non-laboratory environments. Always allow the instrument to stabilize at room temperature after unpacking or relocating the instrument. Humidity should be maintained at laboratory conditions.

3.6 Remote Operation

When the PRS is in

REMOTE

with front panel locked out an REM indication will be shown in the top right of the display.

OPERATION

PRS-300 Series

Chapter 4 USB INTERFACE

4.1 Introduction

The standard USB connection is via a standard USB B female connector located on the rear panel. This can be connected to a

PC via a standard USB 2.0 A Male to B Male

Cable.

Cable

Figure 4-1 USB 2.0 A Male to B Male

The SCPI standard provides a tree like series of standard commands for programmable instruments so that similar instruments by different manufacturers can be controlled by the same program.

4.2 Capabilities

The USB interface provides remote control over all functions except

POWER

4.3 USB Operation

The USB uses the command set outlined in Appendix B.

The standard USB interface uses a standard FTDI chip set.

Normally when the PRS-300 is connected to a computer using the USB port, Windows

7 and higher will search for the correct driver and as long as the computer is connected to the internet the driver should automatically be installed.

If the driver is not automatically installed the drivers can be installed from http://www.

ftdichip.com/Drivers/VCP.htm

USB INTERFACE 12

PRS-300 Series

13 USB INTERFACE

PRS-300 Series

Chapter 5 ETHERNET INTERFACE OPTION

5.1 Ethernet Programming

PRS units, with Ethernet interface option, come with Ethernet remote programming capability accessed through the RJ45 LAN connector. The connector is a RJ45 industrystandard connector found on the rear panel.

The PRS’s Ethernet connection is based upon the ICS Ethernet/GPIB/USB to Serial Interface

Card. More information can be found at www.

icselect.com on the 9006 Ethernet/GPIB/USB to Serial Interface Card.

Ethernet Protocols

The PRS supports Raw Socket and the

VXI-11 protocol which makes it easy to control from a PC or over the company network.

Raw socket lets you telnet to it and is best used with direct PC to instrument applications.

VXI-11 operates over Sun RPC and is a more secure protocol that mimics GPIB control of an instrument and provides secure communication over a company network or over the Internet.

Raw Socket Operation

The PRS is always ready for a telnet connection. When connected, the PRS outputs its IDN message to confirm the connection.

All raw socket messages are terminated with a linefeed. Carriage returns and ignored. A backspace character causes the prior character to be deleted. Communication timeout is two minutes and it is recommended that the client issue a

Space-BS sequence on an occasional basis, less than the timeout, to reset the timeout counter.

VXI-11 Background

VXI-11 is a communication standard developed in conjunction with the VISA Speci fi cation.

The speci fi cation de fi nes a VXI-11.3 interface like the PRS as an instrument which can be controlled in Windows systems by programs that make VISA or SICL library calls and in

UNIX/LINUX or similar operating system with

RPC calls. The VXI-11 speci fi cation provides an RPCL (Remote Procedure Call Library) that can be used by virtually any operating system to control the PRS. Microsoft’s RPC is not ONC compliant and cannot be used with a VXI-11.3 device like the PRS. An VXI-11.3 interface like the PRS will operate in an LXl system and it supports LXI’s ‘VXI Discovery Method’.

5.2 Network Setup

The PRS includes an internal WebServer with

HTML web pages that can be accessed by a web browser from any computer. The web pages let the user quickly change the PRS network settings.

The default IP address is 192.168.1.253 static.

5.3 Ethernet Test Keyboard

To assist the user in setup and communication the VXI-11kybd program can be used which includes defined RPC calls to change the PRS network settings.

VXI-11 Keyboard Control Program provides interactive control of VXI-11 instruments from the computer keyboard without having to write a program. The VXI-11 Keyboard program is the

ETHERNET INTERFACE OPTION

PRS-300 Series

ideal utility program for con fi guring and testing the

PRS or any VXI-11 compatible instrument. Use the VXI-11kybd program to exercise the interface or to try out commands before using them in a program. The VXI-11kybd program can be found on the PRS product page at www.ietlabs.com

Versatile Programming

The PRS can be easily controlled by several programming techniques and languages because it is a VXI-11.3 instrument. If you program with LabVIEW, National Instruments’ VISA supports VXI-11.3 instruments like the PRS. NI’s

Measurement and Automation Explorer treats the PRS as a TCP/IP compliant device. Agilent’s

VISA library supports VXI-11.3 instruments and the Agilent Connection Manager sees the PRS as a TCP/IP instrument.

If you are a Visual Basic, VB.Net or C/C++ programmer, you can write your program to call Agilent’s or National Instruments’ VISA or Agilent’s SICL library in the Windows environment.

If you use LINUX or any other fl avor of UNIX like SunOS, IBM-AIX, HP-UX, or Apple’s OS X, you can communicate with the PRS through RPC over TCP/IP. RPC (or Remote Procedure Calls) provides an invisible communication medium for the developer. The VXI-11 speci fi cation provides an RPCL (Remote Procedure Call Library) that can be used by virtually any operating system to control the PRS.

If you program with Java then you can write a

PRS control program that can be easily moved to many different operating systems.

The Java jGpibEnet project on SourceForge was developed using an ICS 8065 Controller similar to the PRS Controller.

5.4 Network Confi guration

This paragraph con fi gures the 9006 card in the

PRS for operation on your network. The board’s digital interface is con fi gured later by sending commands as outlined in Appendix A.

When shipped, the boards are con fi gured with default settings outlined in Table 4-1 Default

Settings.

Command Function Factory Setting

IP Mode Static or DHCP

Mode

Static

IP Address

Net Mask

0.0.0.0 to

255.255.255.255.0

0.0.0.0 to

255.255.255.255.0

Sets socket timeout COMM Timeout

Auto Disconnect Aborts socket if link count goes to 0

Table 4-1 Default Settings

192.168.1.254

255.255.255.0

120 sec.

Off

Review the Table with your network administrator and decide on which settings, if any, that need to be changed. Table 4-1 provides detailed information about each network setting to help you with your decisions. The minimum change is to set a static IP address so your PC can communicate with the board.

The network con fi guration can be changed and the board’s MAC Address can be read with a web browser, by running ICS’s VXI-11 Con fi guration

Utility on a WIN32 or WIN98 PC. ,

5.5 Web Browser Configuration

Method

This method uses a standard browser such as

Firefox, Internet Explorer or Safari to view and change the current network settings.

1. Temporarily disconnect the computer from the company network. Connect the PRS and computer running the browser using a standard

Ethernet Cables to a hub or switch. Temporarily disconnect the local network connection to avoid network con fl icts until the board is con fi gured.

ETHERNET INTERFACE OPTION

PRS-300 Series

Figure 4-1 9006 Connected to the local hub

An alternate connection is to use an Ethernet

Crossover Cable to connect the computer directly to the PRS for initial con fi guration. This will eliminate any potential network con fl icts while con fi guring the PRS.

a different range, record the current settings and temporarily set the following network values:

Check ‘Use the following IP Address’

IP Address 192.168.1.254

Subnet mask 255.255.255.0

4. Open the browser and enter the default IP address of 192.168.1.254 for new units (or your last set address for older units) in the browser address window.

5. A Welcome Page similar to the one shown

Figure 4-3 should appear in your browser.

6. If you want to change any of the settings, press the ‘Update Configuration’ button. A

Con fi guration Page similar to the one shown in

Figure 4-2 9006 Connected to the local hub

2. Apply power to the PRS. Set the Remote local switch to Remote.

3. Check your computer’s network settings to be sure its IP address is in the 192.168.1.xxx range so it can communicate with the PRS

Ethernet board’s default IP address. If it is not, it must be set before proceeding. Use the values shown below. For Windows PCs, right-click on

My Network Places and click on Properties.

Right-click on Local Area Connection and click

Properties. Highlight Internet Protocol (TCP/IP) and click Properties. If your PC’s IP address is in

Figure 4-3 9006 Welcome Page

ETHERNET INTERFACE OPTION

PRS-300 Series

Figure 4-4 9006 Con fi guration Page

7. Enter the new settings as desired. If you select

DHCP for the TCP/IP Mode, the page blanks out the IP, Net and Gateway addresses as they will be supplied by your DHCP server. Check the entered values carefully as the unit’s webserver does minimal error checking. Press the ‘Update

Flash’ button when done. A Con fi rmation Page similar to the one shown in Figure 4-5 will appear in your browser.

8. Your new settings have been saved in the board’s fl ash memory. You have to reboot the unit or power cycle it for the changes to take affect.

Press the ‘Reboot’ button to reboot the unit now or the ‘Return to the Con fi guration Page’ button to revisit the new settings.

5.6 VXI-11 Configuration Utility

Method

The VXI-11 Configuration Utility program is called ‘VXI11_con fi g.exe’ and runs in any

WIN32 PC with Windows 98, Me, 2K, XP,

Vista, 7 and Server 2003 operating systems. The

VXI11_con fi g.exe program can be found on the

PRS product page at www.ietlabs.com.

The VXI11_con fi g program can be run from the

CD or can be installed onto your hard disk and run from the installation directory.

VXI11_con fi g.exe is a Visual Basic program and requires that either Microsoft’s Visual Studio 6 or VBruntime6 be installed on your PC to run.

1. Connect the board directly to the WIN32 PC that will be running the Con fi guration Utility.

Disconnect the PC from the company network and use the supplied Ethernet Crossover Cable to connect the PC to the board as shown in Figure

4-6. This will eliminate any potential network con fl icts while con fi guring the board.

Figure 4-5 9006 Con fi rmation Page

Figure 4-6 9006 Connected to PC with a

Crossover Cable

Alternately, use a standard Ethernet patch cable

ETHERNET INTERFACE OPTION

PRS-300 Series

to connect the 9006 to the same hub or switch that the PC running the Con fi guration Utility is connected to as shown in Figure 4-7. Temporarily disconnect the local network connection to avoid network con fl icts until the board is con fi gured.

scans for all VXI-11 Services connected to the local LAN or to your PC. (The 9006 is an RPC server which provide a VXI-11 Service) The results are displayed in the Results box.

6. When the servers(s) have been found, use the pulldown arrow in the Found Servers box to view the Found Server addresses. The board’s default address is 192.168.1.254. Highlight the board’s IP address and click the Create Link button. If the server is not found, you can enter the default IP address (192.168.1.254) in the

Found Servers box. Click the Create Link button.

Figure 4-7 9006 Connected to the local hub

2. Apply power to the board

3. Check your PC’s network settings to be sure its IP address is in the 192.168.1.xxx range so it can communicate with the board’s default IP address. To check, right-click on My Network

Places and click on Properties. Right-click on

Local Area Connection and click Properties.

Highlight Internet Protocol (TCP/IP) and click

Properties. If your PC’s IP address is in a different range, record the current settings and temporarily set the following network values:

Check ‘Use the following IP Address’

IP Address 192.168.1.254

Subnet mask 255.255.255.0

4. Run the VXI11_config program. The

Con fi guration Utility opens a window as shown in Figure 4-8. Initially only the Find Server, Help and Exit buttons are enabled on the program window. The other buttons will be enabled as you advance through the program.

5. Click on the Find Server button. The program

Figure 4-8 VXI-11 Con fi guration Utility

(Showing all configuration choices with no changes)

7. When the link has been created, device model number(s) will appear in the ‘Select Device to be Con fi gured’ box. Highlight the desired model number and click the Con fi gure button to start the con fi guration process.

8. The Con fi guration Choices box displays only one line with the fi rst parameter to be changed and its current setting. If you like the current setting, click Enter to advance to the next

ETHERNET INTERFACE OPTION

PRS-300 Series

parameter. If you want to change the setting, type a new value in the New Value box and click

Enter. The program will send your setting to the board and read back the new setting. Repeat as needed to make another change or click Enter again to advance to the next parameter.

9. Repeat step 8 for each con fi guration parameter.

Figure 4-8 shows the VXI-11 Configuration

Utility after all parameters have been entered for a Model 9006. Click the Redo From Start button if you need to start over or if you want to change any of the prior settings

10. When done, the Save Con fi guration button is enabled if you changed any settings. Click the

Save Con fi guration button to save the values in the board’s fl ash memory. If you did not make any changes you can just exit the program.

11. The board has to be power cycled or rebooted before the con fi guration changes take affect.

Click the Reboot button to reboot the board and use the new settings.

12. Press the Exit button to quit the VXI11_con fi g program.

13. If the IP address was changed to an address outside the 192.168.1.xxx range in step 3, your

PC’s network settings will have to be changed to communicate with the board. Exit the VXI11_ con fi g program and restore the PC’s network settings.

5.7 Resetting Default Network

Settings

The board can be reset to the default network settings listed in Table 4-2 at any time by holding the LAN Reset Button in for 5 seconds while applying power to the board. Access to this button is on the rear panel of the PRS-300..

The Digital I/O con fi guration values are not affected by the LAN Reset operation.

Command

IP Mode

IP Address

Net Mask

Function

Static or DHCP

Mode

0.0.0.0 to

255.255.255.255.0

0.0.0.0 to

255.255.255.255.0

Sets socket timeout COMM Timeout

Auto Disconnect Aborts socket if link count goes to 0

Table 4-2 Default Settings

Factory Setting

Static

192.168.0.2

255.255.255.0

120 sec.

Off

5.8 PRS Programming

A PRS SCPI command reference is included in Appendix A. This gives a complete set of commands.

An example of commands to be sent to place the PRS in remote, this must be done fi rst otherwise the will be no remote control of output impedance, and then con fi gure the unit for a speci fi c impedance value.

Where the command string is constructed as described in Appendix A and Appendix B.

A command string might be, for example:

SOURce:DATA 1000000.1

ETHERNET INTERFACE OPTION

PRS-300 Series

Chapter 5 IEEE INTERFACE OPTION

6.1 Introduction

The IEEE interface option makes the

PRS-300 a IEEE-488.2-1987 and SCPI 1994.0 compatible instrument. The PRS-300 IEEE-

488 interface is based upon the ICS Ethernet/

GPIB/USB to Serial Interface Card. More information can be found at www.icselect.

com on the 9006 Ethernet/GPIB/USB to Serial

Interface Card.

The IEEE STD 488.2 covers the electrical and mechanical bus speci fi cations, and state diagrams for each GPIB bus function. It also establishes data formats, common commands for each 488.2 device and controller protocols.

The standard is available on-line at http://www.

ieee.org.

The SCPI standard provides a tree like series of standard commands for programmable instruments so that similar instruments by different manufacturers can be controlled by the same program. SCPI information and a command reference are located in Appendix A.

Other tutorials are available on-line; consult IET for additional information. A software

GPIB “keyboard” can be found at www.ietlabs.

com

6.2 Capabilities

The IEEE option provides remote control over all functions except

POWER

. The IEEE option responds to all Basic Commands in Appendix B and all IEEE.2 Mandated common commands in Appendix A.

6.3 Address Switch and

Communications Settings

The default GPIB address is 4. This address can be changed remotely by sending the command SYSTem:ADDR <n> where n is 0

- 30.

6.4 GPIB Test Keyboard

To aid the user in operating the PRS, a

GPIB “Keyboard” Controller program - the easiest way to control GPIB devices without writing a program - is available from IET. This

GPIB Keyboard program automatically fi nds your device at start-up and it lets you enter just the data that you want to send to the device.

This program works with ICS, Measurement

Computing and National Instruments controllers.

To implement, request a download of

ICS_GPIBkybd_Install.zip

from IET Labs

Tech Support.

IEEE INTERFACE OPTION 20

PRS-300 Series

Unzip the fi le and follow instructions to install.

Open the application. You may use the

Find Listeners

button to con fi rm that the PRS unit is recognized. Other instruments may also be recognized at this time.

IEEE INTERFACE OPTION

Chapter 7 PROGRAMMING

7.1.1 Calibration Interval

The standard USB interface can be programmed via any of the commands listed in

Appendix B.

For USB and RS-232 interfaces, <lf>,

<cr> or <crlf>, can be used as terminator. The device returns in this case <crlf>. The device performs all commands previously sent after it receives a terminator.

The optional Ethernet/IEEE/USB card can be programmed via any of the commands listed in Appendix A and Appendix B.

PRS-300 Series

PROGRAMMING

PRS-300 Series

Chapter 8 MAINTENANCE

8.1 Verifi cation of Performance

8.1.1 Calibration Interval

The PRS Series instruments should be veri fi ed for performance at a calibration interval of twelve (12) months. This procedure may be carried out by the user, if a calibration capability is available, by IET Labs, or by a certi fi ed calibration laboratory. If the user should choose to perform this procedure, then the considerations below should be observed.

8.1.2 General Considerations

It is important, whenever testing the PRS

Series Decade units, to be very aware of the capabilities and limitations of the test instruments used. Such instruments have to be signi fi cantly more accurate than the speci fi ed accuracy for all applicable ranges in order to perform this task, allowing for a band of uncertainty of the instrument itself, the test setup and the environment; consult IET Labs for information.

It is important to allow both the testing instrument and the PRS-300 to stabilize for a number of hours at the nominal operating temperature of 23

C, and at nominal laboratory conditions of humidity. There should be no temperature gradients across the unit under test.

In the case of the PRS-300 a Kelvin type

4-wire test terminals should be used to obtain accurate low-resistance readings.

Steps should be taken to minimize thermal-emf effects, by maintaining an even temperature and by using only low-emf connectors. Use of meters with a “True Ohm” function is recommended.

Proper metrology practices should be followed in performing this veri fi cation.

8.1.3 Calibration Procedure

1. Determine the allowable upper and lower limits for each resistance setting as would be done for a decade box from 0.1 Ω to 20 M Ω s based on the speci fi ed accuracy.

2. Con fi rm that the resistances fall within these limits

3. If any resistances fall outside these limits, See section 8.1.3 Adjustment of internal resistors.

8.1.4 Adjustment of Internal Resistors

During the adjustment process a DMM such as the Fluke 8508A or Keysight 3458A is connected to the binding posts of the PRS-300 using a 4 terminal Kelvin connection.

The PRS-300 has 43 internal resistors which are combined in either series or parallel to achieve the programmed resistance.

These resistors require periodic measurement to keep the PRS-300 within published speci fi cations. The resistors are measured using a DMM. The measured value is then

MAINTENANCE

PRS-300 Series

stored in a table within the memory of the

PRS-300. The measured values of the resistors are used in an algorithm to determine which resistors are used to create the programmed resistance value.

In addition to the 43 resistors the residual internal lead resistance is also measured at time of manufacture and entered into memory. The internal lead resistance does not need to be measured again unless repair has been performed to the PRS-300.

Below is a list of the 43 resistors and their nominal resistance value.

Res. Number Nominal Resistance Value

1 0.17 Ω

0.35

0.7 Ω

1.37

2.66

5.15

10.2

20.0

38.8

11 148.0 Ω

During the adjustment process the fi rmware cycles through each resistor and the technician can enter the measured resistance value in ohms. This should be done with a minimum of 6.5 digits of resolution.

IET Labs offers the PRS-DMM software which works with the PRS-300 and Fluke

8508A or Keysight 3458A to automate this adjustment process.

MAINTENANCE

PRS-300 Series

Appendix A

SCPI COMMAND REFERENCE

SCPI is an acronym for “Standard Commands for Programmable Instruments”. For additional information or an on-line copy of this standard, see:

http://www.scpiconsortium.org.

The IEEE 488.2 Standard was established in 1987 to standardize message protocols and status reporting and to de fi ne a set of common commands for use on the IEEE 488 bus. IEEE

488.2 devices are supposed to receive messages in a more fl exible manner than they send.

A message sent from GPIB controller to GPIB device is called: PROGRAM MESSAGE.

A message sent from device to controller is called: RESPONSE MESSAGE. As part of the protocol standardization the following rules were generated:

(;)

(:) words.

Semicolons separate messages.

Colons separate command

(,) Commas separate data fi elds.

<nl> Line feed and/or EOI as last character

terminates a ‘program message’.

Line feed (ASCII 10) and EOI

terminates a RESPONSE MESSAGE.

(*) Asterisk de fi nes a IEEE 488.2 common command.

(?) Ends a query where a reply is expected.

SCPI builds on the programming syntax of IEEE-488.2 to give the programmer the capability of handling a wide variety of instrument functions in a common manner. This gives all instruments a common “look and feel”. SCPI commands are not case-sensitive.

The portion of commands shown in capitals denotes the abbreviated form of the keyword. Either the abbreviated or whole keyword may be used when entering a complete command. There must be a space between the command and a parameter or channel list. Multiple

SCPI commands may be concatenated together as a compound command by using semicolons as command separators.

APPENDIX A

PRS-300 Series

Keywords shown inside braces [ ] are defaults, and are optional when constructing a

PROGRAM MESSAGE.

Commands not recognized have no effect on the unit’s operation and will set the corresponding bits in the Standard Event Status

Register. SCPI commands that end with a question mark ‘?’ are queries. All queries should be followed by reading their response to avoid data loss.

command line must end with line feed <lf>.

Response from the device also returns line feed

<lf>.

Terminators: For GPIB interface each

Semicolon ‘;’ is used to separate more commands written on one line.

IEEE-488.2 Common Commands

*IDN?

Returns instrument identi fi cation “IET Labs,PRS-300,<Serial Number>,<software version>”

*ESR?

Returns the read of the event status register.

*STB?

Returns the read of the status byte register.

*ESE?

Returns the read of the event status enable register.

*SRE?

Returns the read of the service request enable register.

*ESE

Set the event status enable register value

*SRE

Set the service request enable register value

*RST

Reset the buffer

*TST?

Self test query

*CLS

Clear standard event status register

*OPC

Operation complete

*OPC?

Operation complete query

*WAIT

Wait until operation is complete before executing next command(No Function in PRS)

APPENDIX A

PRS-300 Series

*PCS

Power-on Status Clear

Note: Remote command can start with or without * symbol for compatibility.

2.13 Formats

IEEE 488.2 enables remote programming of all instrument functions, measurement conditions and comparator settings etc. Outputs include measurement conditions, open/short corrections, and measured values.

Data Formats

Data will be transmitted in ASCII NR3 format per IEEE488.2 sec. 8.7.4 and reproduced below.

Note that there is always precisely one digit before the decimal point, and precisely three digits in the exponent.

Multiple results

For the case where a measurement produces multiple results (e.g. MEASure Cs, and DF), the individual numbers will be separated by commas per IEEE488.2 para. 8.4.2.2.

Sequences of Test (Sequence Mode) will be treated as a single Message Unit, with results separated by commas. If a particular test has “None” selected as a secondary parameter, no place will be reserved for the null result. As an example, a sequence of three tests asking for C/D, ESR, and Z/ would appear as follows:

All response messages will be terminated by the NL character together with the EOI line asserted.

Status Byte Register

Decimal

Bit Value

7 128

SRQ, SPOL Resets

Summary of Standard Event

4 16

3 8 None

2 4 None

1 2 None

0 1 None

*The Status Byte Regester is readable via the standard STB? as de fi ned in para. 11.2.2.2 of the

IEEE spec. The 7600 Plus will also implement an SRE register to enable each bit of the Status Byte

Register per para 11.3.2 of the IEEE spec. This register shall be readable by a SRE? command and writeable by a SRE <#> command.

Standard Event Status Register

Use

Power Up Since Last Query

APPENDIX A

PRS-300 Series

6 64

None

Command Error (Syntax)

Execution Error (Over Range, etc.)

No Contact

2 4

1 2

Query Error

None

0 1 Operation Complete

This register is read by executing an “ESR?” command, page 76 (except no *). Note that this is a destructive read. Reading the register clears it. Each bit of the Event register must be enabled in order to cause the ESB bit of the Status Register to be set. This enabling is done in the Standard

Event Status Enable Register by issuing an ESE command.

APPENDIX A

PRS-300 Series

Appendix B

PRS-300 USB and COMMON COMMANDS

COMMON Commands:

*IDN? Returns instrument identi fi cation “IET Labs Inc.,PRS-300,<Serial number>,<software version>”

Serial number in the form “Ax-xxxxxxxx” x = 0 to 9. A = Alpha can be A to Z.

*TST? Self-Test Returns ASCII 0 or 1, 0 = bad or 1 = good

*RST Returns PRS-300 to default “power on” condition

*SAV <number> Saves current resistance value into memory location 0 to 9

Number is 0 to 9

*RCL< number> Recalls resistance value from memory location 0 to 9

Number is 0 to 9

SYSTEM Commands

ber>

SYSTem:SERIal <Ax-xxxxxxxx> Sets the serial number in non-volatile memory < serial num-

Serial number in the form “Ax-xxxxxxxx” x = 0 to 9. A = Alpha can be A to Z.

SYSTem:SERIal? Returns Serial number

SYSTem:CONTrast <number> Sets system contrast speci fi c number from 0 to 15

SYSTem:KEY <number>

<Number> is 0 to 24 keys 0-9 0 – 9

10 – 13

Same as pressing button on front panel of PRS-300

TABLE

RCL, SAV

17 – 18

000 / (-)

ENTER

APPENDIX B

PRS-300 Series

SYSTem:LOCal: This command places device in the LOCAL mode and unlocks all keys on front panel of the device. The Command is valid only for RS232, and USB interfaces.

SYSTem:REMote This command places device in the REMOTE mode and locks all keys. The Command is valid only for RS232, and USB interfaces.

CALIBRATION Commands

CALIbrate:RESistance Goes into calibration mode starting at resistor 1 and then progressing to resistor 43. Each time the command CALI:RES:SET is used the resistor number is automatically incremented by 1.

CALIbrate:RESistance? Returns resistance number to be calibrated.

Numbers 1 to 43

CALIbrate:RESistance:SET <number> Sets calibrated value of resistance in ohms into memory. <number> is a fl oating point number representing the resistance value in ohms for the internal resistor being measured. Each time the command CALI:RES:SET is used the resistor number is automatically incremented by 1.

CALIbrate:RESistance:SET? Returns the calibrated value of resistance in ohms

CALIbrate:DATE <mmddyyyy> Sets calibration date into memory

CALIbrate:DATE?

SOURCE Commands

Returns calibration date in format mmddyyyy

SOURce:DATA <display value> Sets output resistance of the PRS-300 if table is set to 0 or the resistance value corresponding to the display value for the table selected.

Display value in form of number and decimal point representing desired display value.

example SOURce:DATA 1.000002 would set resistance value to 1.000002 Ω if Table is set to

SOURce:DATA? Returns display value currently shown in the PRS display

APPENDIX B

PRS-300 Series

SOURce:RESistance <display value> Sets output resistance of the PRS-300 if table is set to 0 or the resistance value corresponding to the display value for the table selected.

Display value is in the form of number and decimal point representing desired display value.

This is the same as SOURce:DATA command.

example SOURce:RES 0 would set display value to 0 and if Table is set to 1 to 4 this would represent the resistance value depending upon how the table is con fi gured. If in Celsius and PT-100 then resistance of 100 Ω would be set at output of PRS-300.

CONFIGURE Commands

CONFigure:TABLe:SELect <number> Selects Table to be used, <number> is 0 to 4. 0 is no table with display shown in ohms and 1 , 2 and 3 are user de fi ned tables

CONFigure:TABLe:SELect? Returns table number that is selected

CONFigure:TABLe:NAME <name> Sets Table name, <name> is ASCII up to 20 characters such as “PT100”

CONFigure:TABLe:NAME? Returns the number, 1 to 4 ,of currently selected table

CONFigure:TABLe:ERASE Erases all rows in the table

CONFigure:TABLe:ADD <user_value,resistance_value> Adds a row to the end of table showing user value and resistance value in ohms. example CONF:TABL:ADD 20, 95 means that if the table is selected and the operator enters 20 from the front panel the output will be set to 90 Ω .

CONFigure:TABLe:ADD? Returns the last entry in the table

CONFigure:TABLe:DISPlay? Returns all data in the table

Example of information returned

PT100

20, 95

CONFigure:TABLe:UNIT <Unit> Set units for tables up to 8 ASCII characters

As an example “C” could be send for Celsius or “F” for Fahrenheit

CONFigure:TABLe:UNIT? Returns ASCII string representing the units

CONFigure:SELECT <”2” or “4”> Sets “2” Wire or “4” Wire mode

APPENDIX B