LG LH-W753 TA, LHS-W75 TAF, TAC, TAR, TAL, TAW, ACC 75T wireless DVD receiver system Owner's manual

LGESL_LH-W753TA_ENG_102V
@ LG
WIRELESS DVD RECEIVER
SYSTEM
OWNER'S MANUAL
MODEL: LH-W753TA
LH-W753, LHS-W75TAF, LHS-W75TAC,
LHS-W75TAR, LHS-W75TAL,
LHS-W75TAW, ACC75T
PP MER ED MEL JUEE
DIGITAL VIDEO
VIDEO/AUDIO DIGITAL AUDIO MPATIBLE
DM rer
Before connecting up, operating or repairing this
product, please read this instruction booklet
carefully and completely.
Safety Precautions
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK
OF ELECTRIC SHOCK
DO NOT REMOVE COVER (OR BACK)
NO USER-SERVICEABLE PARTS INSIDE
REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.
This lightning flash with arrowhead symbol within an
equilateral triangle is intended to alert the user
about the presence of uninsulated dangerous
voltage within the product’s enclosure that may be
of sufficient magnitude to constitute a risk of electric
shock to persons.
The exclamation mark within an equilateral triangle
is intended to alert the user about the presence of
important operating and maintenance (servicing)
instructions in the instructions accompanying the
product.
WARNING: TO PREVENT FIRE OR ELECTRIC SHOCK
HAZARD, DO NOT EXPOSE THIS PRODUCT TO RAIN OR
MOISTURE.
WARNING: Do not install this equipment in a confined space
such as a book case or similar unit.
CLASS 1 LASER PRODUCT
KLASSE 1 LASER PRODUKT
LUOKAN 1 LASER LAITE
KLASS 1 LASER APPARAT
CLASSE 1 PRODUIT LASER
CAUTION:
This DVD/CD receiver employs a laser system.
To ensure proper use of this product, please read this owner's
manual carefully and retain it for future reference. Should the
unit require maintenance, contact an authorized service loca-
tion (see service procedure).
Performing controls, adjustments, or carrying out procedures
other than those specified herein may result in hazardous radi-
ation exposure.
To prevent direct exposure to laser beam, do not try to open
the enclosure. Visible laser radiation when open. DO NOT
STARE INTO BEAM.
CAUTION: The apparatus should not be exposed to water
(dripping or splashing) and no objects filled with liquids, such
as vases, should be placed on the apparatus.
CAUTION: This product may not be used outdoor, restricted to
indoor use only.
About the symbols for instructions
A Indicates hazards likely to cause harm to the unit
itself or other material damage.
Indicates special operating features of this unit.
Indicates tips and hints for making the task easier.
Manufactured under license from Dolby Laboratories. “Dolby”,
“Pro Logic”, and the double-D symbol are trademarks of Dolby
Laboratories. Confidential Unpublished works. Copyright 1992-
1997 Dolby Laboratories. All rights reserved.
Manufactured under license from Digital Theater Systems, Inc.
US Pat. No. 5,451,942 5,956,674, 5,974,380, 5,978,762 and
other worldwide patents issued and pending. “DIS” and “DTS
Digital Surround” are registered trademarks of Digital Theater
Systems, Inc. Copyright 1996, 2000 Digital Theater Systems,
Inc. All rights reserved.
E OTES ON COPYRIGHTS:
It is forbidden by law to copy. broadcast, show, broadcast
via cable, play in public, or rent copyrighted material without
permission.
This product features the copy protection function developed
by Macrovision. Copy protection signals are recorded on some
discs. When recording and playing the pictures of these discs
on a VCR, picture noise will appear.
This product incorporates copyright protection technology that
Is protected by method claims of certain U.S. patents and other
intellectual property rights owned by Macrovision Corporation
and other rights owners. Use of this copyright protection tech-
nology must be authorized by Macrovision Corporation, and is
intended for home and other limited viewing uses only unless
otherwise authorized by Macrovision Corporation. Reverse
engineering or disassembly is prohibited.
SERIAL NUMBER: The serial number is located on the back
of this unit. This number is unique to this unit and not available
to others. You should record requested information here and
retain this guide as a permanent record of your purchase.
Model No.
Serial No.
Table of Contents
Introduction
Safety Precautions ......................... 2
TableofContents .......................... 3
BeforeUse ............................. 4-5
Playable Discs... ........................ 4
Precautions. ............................ 5
Notes on Discs .......................... 5
About SymbolS 0000014 1 a 14 5
Front Panel and Rear Panel .................. 6
Remote Control Overview.................... 7
Preparation
Connections. ................ ci... 8-13
TV Connections ......................... 8
Optional Equipment Connections ............ 9
Aerial Connections. ............ ere. 10
Speaker System Connection ............. 11-12
e Transmitter. .. ........ KH 11
e Changing a channel of Transmitter. ....... 11
e Setting a ID of Transmitter .............. 11
e Assembling and Connecting to the Speakers 11
e Speaker Connections. ............ ee... 12
Speaker Positioning... ................... 13
Before Operation ....................... 14-19
Mini Glossary for Audio Stream & Surround
Mode. ......... e rrrreerar0re0 e. 14
Sound Mode .......... 2... a ee 14
On-Screen Display . .................... 15
Initial Settings... ..................... 16-19
e General Operation. . .................. 16
® Гапдиаде .......................... 16
eDisplay.............. .. 2... .... 16-17
e Audio. ......... 2 en. 17
e Lock (Parental Control) ................ 18
e Others. ........ e. e... erecaredae. 19
Operation
DVD or Video CD Operation. .............. 19-22
Playing a DVD and Video CD... ............ 19
General Features ..................... 20-22
e Moving to another TITLE/GROUP ........ 20
e Moving to another CHAPTER/TRACK ..... 20
e Slow Motion. ........................ 20
e Still Picture and Frame-by-Frame Playback . 20
e Search. ........... aerea. 20
® Repeat ......... ee 6 20
® Нереа? А-В ......................... 21
eTimeSearch ........................ 21
e Marker Search. . ..................... 21
@ ZOOM. . eee 21
Special DVD Features . . .................. 22
eTlitleMenu.......................... 22
eDiscMenu.......................... 22
e Changing the Audio Language. .......... 22
e Changing the Audio Channel. ........... 22
e Subtitles . ......... 02.0... . 22
DVDAudioDiscs ........................ 22
Audio CD and MP3/WMA Disc ...............
Playing an Audio CD and MP3/WMA Disc
e Pause ......... 4 4 4 44 400
e Moving to another Track ...............
e Repeat Track/AlN/Off. ............. .....
e Search. ........... a 4 0 4 44 0 0
JPEG Disc Operation ......................
Viewinga JPEG disc .....................
e SlideShow .........................
e Still Picture . ........................
e Moving to another file .................
® fo rotate picture... ............. .......
Programmed Playback .....................
Repeat Programmed Tracks. . ..............
Erasing a Track from Programme List ........
Erasing the Complete Programme List .......
DivX Disc Operation .......................
Speaker Setup. ................. ia...
Additional Information .....................
Last Condition Memory ...................
Screen Saver. ........ 2.0.0.0,
System Select... ......... LL.
Controlling the TV .......................
Operation with Radio ......................
Presetting the radio stations. . ..............
Listeningtotheradio.....................
Other Functions. ..........................
Sleep Timer Setting . .....................
Dimmer .......... ere.
Mute ......... errar
Reference
Language Code List ....................... 31
Country Code List. ........................ 31
Troubleshooting. . ...................... 32-33
Specifications ............................ 34
Before Use
Playable Discs
DVD
VIDEO" (8 em/ 12 cm disc)
DVD audio discs
AUDIO" (8 em/ 12 cm disc)
Ten Video CD (VCD
(8 ст / 2 от diso)
COMPACT
Audio CD
DIGITAL AUDIO (8 cm/ 12 cm disc)
In addition, this unit can play a DVD-RW, DVD+RW,
SVCD and CD-R or CD-RW that contains audio titles,
MP3, WMA, JPEG or DivX files.
otes
e Depending on the conditions of the recording equip-
ment or the CD-R/RW (or DVD-RW, DVD+RW) disc
itself, some CD-R/RW (or DVD-RW, DVD+RW) discs
cannot be played on the unit.
e Do not attach any seal or label to either side (the
labeled side or the recorded side) of a disc.
e Do not use irregularly shaped CDs (e.g., heart-shaped
or octagonal). It may result in malfunctions.
EN otes on DVDs and Video CDs
Some playback operations of DVDs and Video CDs
may be intentionally fixed by software manufacturers.
As this unit plays DVDs and Video CDs according to
disc content designed by the software manufacturer,
some playback features of the unit may not be available
or other functions may be added.
Make sure to also refer to the instructions supplied with
the DVDs and Video CDs. Some DVDs made for busi-
ness purposes may not be able to be played on the
unit.
Regional code of the DVD/CD receiver and DVDs
This DVD/CD Receiver is designed and manufactured for
playback of region “3” encoded DVD software.
The region code on the labels of some DVDs ©
indicates which type of player can play those
discs. This unit can only play DVDs labeled “3” or “ALL”.
If you try to play any other discs, the message “Check
Regional Code” will appear on the TV screen. Some
DVDs that have no region code label may still be subject
to area restrictions and therefore not playable.
ote on DTS-encoded CDs
When playing DTS-encoded CDs, excessive audio level
may be heard from the analog stereo output. To avoid
possible damage to the audio system, turn down the
volume before playing back such discs, adjust the
volume gradually, and keep the volume level low. To
enjoy DTS Digital Surround™ playback, an external 5.1
channel DTS Digital Surround™ decoder system must
be connected to the digital output of the unit.
Disc-related terms
Title (DVD only)
The main film content or accompanying feature content
or additional feature content, or music album.
Each title is assigned a title reference number enabling
you to locate it easily.
Chapter (DVD only)
Sections of a picture or a musical piece that are smaller
than titles. A title is composed of one or several chap-
ters. Each chapter is assigned a chapter number,
enabling you to locate the chapter you want. Depending
on the disc, chapters may not be recorded.
Group (DVD audio discs only)
The main audio content or accompanying feature con-
tent or additional feature content, or music album. Each
group is assigned a group reference number enabling
you to locate it easily.
Scene (VCD)
On a Video CD with PBC (Playback control) functions,
moving pictures and still pictures are divided into sec-
tions called “Scenes”. Each scene is displayed in the
menu screen and assigned a scene number, enabling
you to locate the scene you want.
A scene is composed of one or several tracks.
Types of Video CDs
There are two types of Video CDs:
Video CDs equipped with PBC (Version 2.0)
PBC (Playback control) functions allow you to interact
with the system via menus, search functions, or other
typical computer-like operations. Moreover, still pictures
of high resolution can be played if they are included in
the disc.
Video CDs not equipped with PBC (Version 1.1)
Operated in the same way as audio CDs, these discs
allow playback of video pictures as well as sound, but
they are not equipped with PBC.
“Before Use (Continued)
Precautions
Handling the unit
When shipping the unit
The original shipping carton and packing materials may
come in handy. For maximum protection, re-pack the
unit as it was originally packed at the factory.
When setting up the unit
The picture and sound of a nearby TV, VCR, or radio
may be disturbed during playback. In this case, position
the unit away from the TV, VCR, or radio, or turn off the
unit after removing the disc.
To keep the exterior surfaces clean
Do not use volatile liquids, such as insecticide spray,
near the unit. Do not leave rubber or plastic products in
contact with the unit for a long period of time. They will
leave marks on the surface.
Cleaning the unit
To clean the cabinet
Use a soft, dry cloth. If the surfaces are extremely dirty,
use a soft cloth lightly moistened with a mild detergent
solution. Do not use strong solvents such as alcohol,
benzene, or thinner, as these might damage the surface
of the unit.
To obtain a clear picture
The DVD/CD Receiver is a high-tech, precision device.
If the optical pick-up lens and disc drive parts are dirty
or worn, the picture quality will be poor.
Regular inspection and maintenance are recommended
after every 1,000 hours of use. (This depends on the
operating environment.)
For details, please contact your nearest dealer.
Notes on Discs
Disc Handling
Do not touch the playback side of the disc.
Hold the disc by the edges so that fingerprints will not
get on the surface.
Do not stick paper or tape on the disc.
Storing discs
After playing, store the disc in its case.
Do not expose the disc to direct sunlight or sources of
heat, or leave it in a parked car exposed to direct sun-
light, as there may be a considerable temperature
increase inside the car.
Cleaning discs
Fingerprints and dust on the disc can distort the picture
or reduce sound quality. Before playing, clean the disc
with a clean cloth. Wipe the disc from the centre out-
wards.
O X
Do not use strong solvents such as alcohol, benzene,
thinner, commercially available cleaners, or anti-static
spray intended for vinyl records.
About Symbols
About the W symbol display
“> may appear on the TV screen during operation.
This icon means the function explained in this owner's
manual is not available on that specific DVD-Video disc.
About the disc symbols for instructions
A section whose title has one of the following symbol is
applicable only to the disc represented by the symbol.
DVD and finalized DVD+R/RW.
DVD Audio discs.
Video CDs with the PBC (playback control)
function.
Video CDs without the PBC (playback control)
function.
Audio CDs.
€ MP3 disc.
CY WMA disc.
JPEG disc.
ES Divx disc.
“Front Panel and Rear Panel
MIC 1/MIC 2
Connect a microphone to MIC 1 or
MIC 2 or to both sockets.
DISC Tray
STANDBY/ON PHONES connector
STANDBY indicator
Lights red when the receiver
is in Standby mode (off).
FUNCTION/PLAY
Press and hold down this button about 3
seconds, then press repeatedly to select
other function.
VOLUME controller
DISPLAY Window
aera o L
"7
de
J EN 222 I
OPEN/CLOSE button
USB host
Remote sensor
Connect to a USB port of MOUSE STER
JS MOOS TUNING(-/+)/SKIP(-/+)
| memory etc.) STOP buttons
Power Cord
SPEAKER connectors
FM Antenna connector
AV2 AUDIO Input
(L/R)/VIDEO IN TRANSMITTER
Connectors (DC 7V OUT)
Connector
— ——
SVIDEO © O ©
® й ©1© ©: === |e
| E pr o ao
AM Loop Antenna connectors |
S-VIDEO OUT connector OPTICAL IN
MONITOR OUT connector connector
COMPONENT VIDEO OUT terminals
Connect to a TV with Y Pb Pr inputs.
AV1 AUDIO Input (L/R)/VIDEO IN Connectors
A
Do not touch the inner pins of the jacks on the rear
panel. Electrostatic discharge may cause permanent
damage to the unit.
«<>
"Remote Control Overview
POWER
* POWER
O
DVD
Select the output source (CD/DVD) or
accesses
BAND
Select the System's tuner (FM and AM
bands)
: MUTE
0-9 numerical buttons
© © ©
OPEN/CLOSE (4)
Opens and closes the disc tray.
AUX
Selects input source.
TV
To control the TV. (LG TV only)
SLEEP
Set the System to turn off automatically.
at a specified time.
Select a service, programme number oi MUTE
directly or select numbered options in a Mute the speakers.
menu. 7 8 9 о SUBTITLE
XTS pro e = Selects a subtitle language (DVD).
To enjoy more natural and realistic RETURN
sound. Removes the setup menu.
XTS e e MARKER
To enjoy great sound effect. Marks a point during playback.
AUDIO e e SEARCH
Selects an audio language (DVD) or
an audio channel (CD).
SOUND MODE e
Selects the sound mode. e
SETUP
Accesses or removes setup menu . e
MENU
Accesses the menu on a DVD disc.
SCAN-/+(<</P>>) e
Search backward or forward.
SLOW-/+(<1/1>) e
Reverse/ Forward slow playback.
REVERSE SKIP(t<<) e
Search backward*/go to beginning of
current chapter or track or go to
previous chapter or track.
FORWARD SKIP(P>PI) e
Search forward*/go to next
>
— SKIP +
44 pr
chapter or track. °
PROG.
Accesses or removes Program menu, o
MEMO. e
Enter a radio station's frequency into ©
the tuner.
CLEAR e °
Removes a track number on the
program menu or a mark on the e
MARKER SEARCH menu.
REPEAT e
Repeat chapter, track, title, all.
REPEAT A-B e °
Repeats sequence.
®
ECHO VOL.(V/A)
Adjusts echo volume.
MIC VOL.(V/A)
Adjusts microphone volume.
Remote Control Operation Range
Displays MARKER SEARCH menu.
DISPLAY
Accesses On-Screen display.
INPUT
Selects the TV's source.
<4/»/A/V (left/right/up/down)
Selects an option in the menu.
ENTER
Acknowledges the menu selection.
PRESET/CH(+/-) (A/V):
Select programme of TV or Radio.
TUN(-/+) (4/»):
To tune in the desired radio station.
TITLE
Displays the disc's Title menu, rf available.
VOLUME (+/-)
To adjust speaker volume and TV volume.
PLAY (»)
Starts playback.
PAUSE/STEP (HN)
Pause playback
STOP (MM
Stops playback.
ZOOM
Enlarges the DVD video image.
DIMMER
Press to change brightness of the
display window on the front panel
dur-ing in power-on status.
D.INPUT
To select a digital input source.
USB
To enjoy the multimedia files.
Remote control battery installation
Point the remote control at the remote sensor and press the
buttons.
e Distance: About 23 ft (7 m) from the front of the remote sen-
sor
e Angle: About 30° in each direction in front of the remote sensor
A Caution
Do not mix old and new batteries. Never mix different types of batteries (standard, alkaline, etc.).
Remove the battery cover on the rear of the
A remote control, and insert two RO3 (size
AAA) batteries with @ and @ aligned
correctly.
«р
Connections
TV Connections
e Make one of the following connections, depending on
the capabilities of your existing equipment.
ips
e Depending on your TV and other equipment you wish
to connect, there are various ways you could connect
the DVD/CD Receiver. Use one of the connection
methods described below.
e Please refer to the manuals of your TV, VCR, Stereo
System or other devices as necessary to make the
best connections.
A caution
e Make sure the DVD/CD Receiver is connected directly
to the TV. Select the correct AV input on your TV.
e Do not connect your DVD/CD Receiver to TV via your
VCR. The DVD image could be distorted by the copy
protection system.
S-Video connection
Connect the S-VIDEO OUT jack on the DVD/CD
Receiver to the S-VIDEO IN jack on the TV using the
S-Video cable (S).
Video connection
Connect the MONITOR OUT jack from the DVD/CD
Receiver to the VIDEO IN jack on the TV using the
video cable supplied (V).
Component Video (Color Stream®) connection
Connect the COMPONENT VIDEO OUT jacks from the
DVD/CD Receiver to the corresponding in jacks on the
TV using an Y Pb Pr cable (C).
Progressive Scan (ColorStream* pro)
connection
e If your television is a high-definition or “digital ready”
television, you may take advantage of the DVD/CD
Receiver's progressive scan output for the highest
video resolution possible.
e If your TV does not accept the Progressive Scan
format, the picture will appear scrambled if you try
Progressive Scan on the DVD/CD Receiver.
Connect the COMPONENT VIDEO OUT jacks from the
DVD/CD Receiver to the corresponding in jacks on the
TV using an optional Y Pb Pr cable (C).
Rear of TV
VIDEO
Fr \ Fr R) Lp N
\ i A y y
r
3
a a
—
S-VIDEO
OUT
(E
QR
de
5-9
MO
MTOR| COMPONENT
AV2 IN AMT IN
UT VIDEO OUT À
Q
Rear of DVD/CD Receiver
otes
e Set the Progressive to “On” on the Setup menu for
progressive signal, see page 17.
e Set the progressive to “Off” by removing any disc
from the unit and close the disc tray. see that “no
disc” is displayed on the display window. Then, press
STOP and hold it for five seconds before releasing it.
e Progressive scan does not work with the analog
video connections (yellow VIDEO OUT jack) or
S-VIDEO connection.
“Connections (Continued)
Optional Equipment Connections
1 Connect a VCR to the AV IN connectors.
2 Connect a additional VCR to the AV2 connectors.
Connect an optical output of DVD Player (or Digital Device etc) to the OPTICAL IN connector.
A Connect the USB port of a USB Memory (or MP3 player, etc.) to the USB HOST on the front of the unit.
VCR
Additional VCR
Front of DVD/CD Receiver
To AUDIO OUT (L/Ry
VIDEO OUT DVD Player (or Digital
Device, etc)
— 70 }-
OPTICAL
OUT
To AUDIO OUT (LRy
VIDEO OUT
USB Memory, MP3 Player (or
Memory Card Reader, etc.)
To AUDIO IN (L/RY
VIDEO IN (AV1)
To AUDIO IN (L/RY
VIDEO IN (AV2)
® (a) Of /
ga ©0% ©
otes
e |[f the audio format of the digital output does not match the capabilities of your DVD/CD Receiver, the receiver will
produce a strong, distorted sound or no sound at all.
e The DivX files in your memory card will not be able to be play.
‘Connections (Continued)
Aerial Connections
Connect the supplied FM/AM aerial for listening to the radio.
e Connect the AM Loop aerial to the AM aerial connector,
e Connect the FM Wire aerial to the FM aerial connector.
AM Loop aeri
FM Wire aerial (supplied)
Ny H Ро WOOP CENTER RES No JC) © ma
Y JA DA | 1 II P hh
© aille ==
SS SS SE
— 11111 1 ©
fe
otes
e To prevent noise pickup, keep the AM Loop aerial away from the DVD/CD Receiver and other components.
e Be sure to fully extend the FM wire aerial.
e After connecting the FM Wire aerial, keep it as horizontal as possible.
“Connections (Continued)
Speaker System Connection Assembling and Connecting to
the Speakers
E ote
If there is a strong electromagnetic wave product
nearby, an interference may be occurred.
(EX : Micro wave oven)
The front and rear speakers are detached from the
speaker stands. Connect the speaker cords and assem-
ble the front and rear speakers from speaker stands as
illustrated.
Transmitter e Connect the speaker cords to the appropriate termi-
nals on the bottom of each front and rear speaker.
e After connecting the speaker cords to the appropriate
terminals on the bottom of each front and rear speak-
er and attach the front and rear speakers to the
speaker stands.
LED indicator
Displays the operated
status.
DC IN connector
ID/CHANNEL (ID./CH.)
button
SOUND SIGNAL
connector
Changing a channel of Transmitter
If there is a similar wireless product nearby, interference
may occur. In this case, change to other channel using
ID/CHANNEL (ID./CH.) button of transmitter. E ote
Press the ID/CHANNEL (ID./CH.) button for less ® You cannot detach the speaker from the stand after assem-
than about 3 seconds. bling the front and rear speakers.
ote
The wireless speakers may not received the changed channel of
transmitter. In this case set the ID as below.
Setting a ID of Transmitter
When you connect the wireless speaker for the first
time, the blue and red LED indicator of wireless speaker
blinks in turn and then the ID will be set automatically.
If an interference is occurred or you use a new wireless
speaker, set the ID.
1. Press the ID/CHANNEL (ID./CH.) button for more
than about 3 seconds.
The blue LED indicator blinks.
2. Turn the transmitter and wireless speaker off and
then turn it on.
“Connections (Continued)
Speaker System Connection
Speaker Connections
Connect the speakers to the front (right, left) or center speaker connectors.
Connect the subwoofer to the woofer connector.
Connect the power cord of the wireless speaker to the outlet.
Connect the DC IN connector of transmitter and the transmitter connector of rear panel with the DC power cable.
Connect the SOUND SIGNAL connector of transmitter and the rear (right, left) speaker connector of rear panel
with the SOUND SIGNAL cable.
Set the distance between the transmitter and wireless speaker (right, left) within 10m.
Front speaker
(Left)
Front speaker
(Right)
Center speaker
:
у
1
в
©]
®
©
em fan} (60) Fo
m“
Sound signal
cable
Subwoofer
Wireless Speaker
Wireless Speaker
(Right)
(Left) ~ e DC power cable
Notes:
Optimum performance can be implemented only when the transmitter and the wireless speaker within distance of 2m through
10m is used since communication failure may occur if closely approaching distance between them.
Be sure to match the speaker cable to the appropriate terminal on the components: + to + and — to — If the cables are
reversed, the sound will be distorted and will lack base.
Do not remove the front cover of supplied speaker.
It takes a few seconds (and may take longer) for the transmitter and wireless speaker (left, right) to communicate with each
other.
When the main set is turned off, the transmitter is also turned off automatically and the wireless speaker is in standby mode
(red LED indicator).
If the wireless speaker is turned off, the wireless speaker will not function.
w
“Connections (Continued)
Speaker Positioning
In the case of normal position use the 6 speakers (2 front speakers, centre speaker, 2 rear speakers and sub-
woofer). If you want to play the excellent bass sound, DTS digital surround or Dolby Digital surround, you should
connect a subwoofer,
* Front speakers
According to your listening position set up the speakers for equal distance. And by hearing position set up the interval between
speakers to 45 degree.
- Centre speaker
The centre speakers and front speakers are ideally the same height. But normally place it above or below the television.
* Rear speakers
Place left and right behind the listening area. These speakers recreate sound motion and atmosphere required for surround
sound playback. For best results, do not install the rear speakers too far behind the listening position and install them at or
above the level of the listener's ears. It is also effective to direct the rear speakers towards a wall or ceiling to further disperse
the sound.
In the case of a smaller room size, if the audience is near to the rear wall set the rear speakers opposite each other, and set the
rear speakers above 60 - 90 cm than the listener’s ears.
+ Subwoofer
This can be placed in any front position.
Subwoofer
Centre Speaker
Front Speaker Front Speaker
(Left) (Right)
Rear Speaker
Rear Speaker
a : q e
Speaker Positioning Example
Before Operation
Mini Glossary for Audio Stream &
Surround mode
ETS
Allows you to enjoy 5.1(or 6) discrete channels of high
quality digital audio from DTS program sources such as
discs, DVD and compact discs, etc.bearing the trade-
mark. DTS Digital Surround delivers up to 6 channels of
transparent audio(which means identical to the original
masters) and results in exceptional clarity throughout a
true 360 degree sound field. The term DTS is a trade-
mark of DTS Technology, LLC. Manufactured under
license from DTS Technology, LLC.
DEIDIGITAL
The Dolby Digital surround format lets you enjoy up to
5.1 channels of digital surround sound from a Dolby
mark, you can enjoy even better sound quality, greater
spatial accuracy, and improved dynamic range.
DKMPRO LOGIC (IT)
Dolby Pro Logic Il creates five full-bandwidth output
channels from two-channel sources. This is done using
an advanced, high-purity matrix surround decoder that
extracts the spatial properties of the original recording
without adding any new sounds or tonal colorations.
MOVIE mode:
The Movie mode is for use with stereo television
shows and all programs encoded in Dolby Surround.
The result is enhanced soundfield directionality that
approaches the quality of discrete 5.1-channel sound.
MUSIC mode:
The Music mode is for use with any stereo music
recordings.
MATRIX mode:
The Matrix mode is the same as the Music mode
except that the directional enhancement logic is
turned off. It may be used to enhance mono signals
by making them seem “larger.” The Matrix mode may
also find use in auto systems, where the fluctuations
from poor FM stereo reception can otherwise cause
disturbing surround signals from a logic decoder. The
ultimate “cure” for poor FM stereo reception may be
simply to force the audio to mono.
BYPASS
Software with multichannel surround audio signals is
played according to the way it was recorded.
Sound Mode
You can enjoy surround sound simply by selecting one
of the pre-programmed sound fields according to the
program you want to listen to.
When DVD is inserted
You can change the Digital Audio Output mode by
pressing the AUDIO button on the remote control during
playback. Although the DVD contents differ from disc to
disc, the following explains the basic operation when
this feature is used.
a) After you select 2 channel (For example 2= or
2% ) by pressing AUDIO button, press SOUND
button repeatedly.
e Bypass | > Mal Movie | <> ‚© Music | > «© Matrix
b) After you select 5.1 channel (For example %,æ
225) by pressing AUDIO button, press SOUND button.
- “M4” indicator will be displayed on the TV screen.
- “BYPASS” indicator will be only displayed on the display
window.
When Video CD is inserted
Each time you press SOUND button, the sound mode
of Video CD is changed on the display window in the
following order.
BYPASS > STUDIO — CLUB — HALL —
THEATER 1 > CHURCH > PL Il MOVIE —
PL Il MUSIC — PL Il MTRX — BYPASS...
ote
After you select the “Bypass” of sound mode by
pressing SOUND button, press AUDIO button.
The Left, Right and Stereo of audio channel will be
displayed on the TV screen.
When CD is inserted
Each time you press SOUND button, the sound mode
of Audio CD is changed on the display window in the
following order.
BYPASS > STUDIO — CLUB — HALL —
THEATER 1 > CHURCH > PL TI MOVIE >
PL I MUSIC — PL Il MTRX — BYPASS...
For your reference
* You can identify the encoding format of program
software by looking at its packaging.
- Dolby Surround encoded programs are labeled with
the Mr logo.
- DTS Digital Surround discs are marked with DTS.
ote
e When you play sound tracks with 96kHz sampling frequen-
Cy, the output signals will be converted to 48kHz (sampling
frequency).
e When you use a microphone, you can't enjoy 5.1 channel
output. Only 2 channel sound will out by the influence of the
microphone system.
Before Operation (Continued)
On-Screen Display
You can display the general playback status on the TV
screen. Some items can be changed using the menu.
To use the on-screen display:
1 Press DISPLAY during playback.
Press A / ¥ to select an item.
The selected item is highlighted.
Press «< / P to change the setting. You can also
use the number buttons if appropriate (e.g.
inputting the title number). For some functions,
press ENTER to execute the setting.
PLAYBACK STATUS/RESTRICTIONS
2 me | Repeat title
2 as | Repeat sequence
um | Resume play from this point
& Action prohibited or not available
otes
e Some discs may not provide all of the features
shown below.
e |f no button is pressed for 10 seconds, the on-
screen display disappears.
Example: On-Screen Display during
playing DVD Video
ltems Selection Method
Title Number & 1. | < / >, Numbers
ENTER
Chapter Number Es « </ P, Numbers
p ES 1/12» ENTER
Time search 5 0:20:09 Numbers, ENTER
Audio language
ai ; < / Por
and Digital Audio a TD
Output mode = 3/2.1CH AUDIO
Subtitle language | «< / >» ог
guage NEE SUBTITLE
Angle os TT </p>
Sound ‚© Bypass | « / >
Example: On-Screen Display during
playing VCD
Items Selection Method
Track Number & 1a | « / », Numbers
(ог PBC mode) ENTER
Time search B 0200 | TE
< / Por
Audio Channel бя stereo» AUDIO
Sound © Bypass | </>
Example: On-Screen Display during
playing DVD Audio
Items Selection Method
G Numb Е « / >, Numbers
roup Number E 12 | ENTER
« / >, Numbers
Track Number §3 1/6» ENTER
Time search $ 0:20:00 | Display only
Audio language me
and Digital Audio + em | AUDIO
Output mode deer
Subtitle language El ое» | Display only
Page (or Angle) [EX « 1/215 </>
or
Clee 1/3»
Before Operation (Continued)
Initial Settings
By using the Setup menu, you can make various adjust-
ments to items such as picture and sound. You can also
set a language for the subtitles and the Setup menu,
among other things. For details on each Setup menu
item, see pages 16 to 19.
To display and exit the Menu:
Press SET UP to display the menu. A second press of
SET UP will take you back to initial screen.
To go to the next level:
Press > on the remote control.
To go back to the previous level:
Press 4 on the remote control.
General Operation
Press SET UP.
The setup menu appears.
Use A/V to select the desired option then
press > to move to the second level.
The screen will be shown the current setting for the
selected item, as well as alternate setting(s).
Use A/V to select the second desired option
then press P to move to the third level.
Use À / V to select the desired setting then press
ENTER to confirm your selection.
Some items require additional steps.
5 Press SET UP or PLAY to exit the setup menu.
LANGUAGE
LANGUAGE
osD English
Disc Audio Original
Disc Subtitle Off
Disc Menu Original
& Move LE Те
OSD
Select a language for the Setup menu and on-screen display.
Disc Audio / Subtitle / Menu
Select the language you prefer for the audio track (disc
audio), subtitles, and the disc menu.
Original: Refers to the original language in which the
disc was recorded.
Other: To select another language, press number
buttons to enter the corresponding 4-digit number
according to the language code list on page 31. If you
enter the wrong language code, press CLEAR on the
remote control.
DISPLAY
DISPLAY
TY Aspect 16 : 9
Display Mode Widescreen
Progressive Scan Off
$ Move > Select
TV Aspect
4:3: Select when a standard 4:3 TV is connected.
16:9: Select when a 16:9 wide TV is connected.
Display Mode
Display Mode setting works only when the TV Aspect
mode is set to “4:3”.
Letterbox: Displays a wide picture with bands on the
upper and lower portions of the screen.
Panscan: Automatically displays the wide picture on
the entire screen and cuts off the portions that do not fit.
Before Operation (Continued)
Progressive Scan
Progressive Scan Video provides the highest quality
pictures with less flickering.
If you are using the COMPONENT VIDEO OUT jacks,
but are connecting the receiver to a standard (analog)
television, set Progressive Scan to Off.
If you are using the Component Video jacks for
connection to a TV or monitor that is compatible with a
progressive scan signal, set Progressive Scan to On.
Select “Progressive Scan” on the DISPLAY
menu then press №.
DISPLAY
RR: ETT
Display Mode
Progressive Scan >
4 Move P Select
2 Select “On” using the À / Y buttons.
Press ENTER to confirm your selection.
The confirm menu will appear.
When the confirm menu appears on your screen
Cancel is highlighted as default. Use the < / »
buttons to highlight Enter.
Pressing ENTER will set the DVD/CD Receiver
to Progressive scan mode.
ote
e Progressive Scan will not be displayed in the setup
menu when the VIDEO OUT SELECTOR switch is
set at SCART position.
A caution
Once the setting for progressive scan output is entered,
an image will only be visible on a progressive scan
compatible TV or monitor. If you set Progressive Scan
to On in error, you must reset the unit.
1) Remove any disc from the unit and close the disc
tray. See that “NO DISC” is displayed on the display
window
2) Press and hold STOP (IM) for five seconds then
release it. The video output will be restored to the
standard setting, and a picture will once again be
visible on a conventional analog TV or monitor.
AUDIO
Each DVD disc has a variety of audio output options.
Set the DVD/CD Receiver's AUDIO options according to
the type of audio system you use.
AUDIO
5.1 Speaker Setup
DRC
Vocal
$ Move ЕСТ Ts
5.1 Speaker Setup
Select speaker settings, including volume balance and
distance, or test the speaker settings.
Speaker settings are only active on the Analog Multi-
Channel Output. (See “Speaker Setting” page 27)
Dynamic Range Control (DRC)
Cy
With the DVD format, you can hear a program's sound-
track in the most accurate and realistic presentation
possible, thanks to digital audio technology. However,
you may wish to compress the dynamic range of the
audio output (the difference between the loudest sounds
and the quietest ones). Then, you may listen to a movie
at a lower volume without losing dialog intelligibility.
Set DRC to On for this effect.
EN otes
e The DRC function works only during playback of
Dolby Digital recorded discs.
e The level of Dynamic Range Compression may differ
depending on the DVD disc.
Vocal Wal
Set Vocal to On only when a multi-channel Karaoke
DVD is playing. The karaoke channels on the disc will
mix into a normal stereo sound.
“Before Operation (Continued)
LOCK (Parental Control)
LOCK
Rating » Unlock
Password ур | 6800
Country Code y
J TER > Select
Rating
Some movies contain scenes that may not be suitable
for children to view. Many of these discs contain parental
control information that applies to the complete disc or to
certain scenes on the disc. Movies and scenes are rated
from 1 to 8, depending on the country. Some discs offer
more suitable scenes as an alternative.
The parental control feature allows you to block access
to scenes below the rating you input, thereby preventing
your children from being able to view material you
believe is unsuitable.
1 Select “Rating” on the LOCK menu then, press
>.
To access the Rating, Password and Country
Code features, you must input the 4-digit
security code you created.
If you have not yet entered a security code you are
prompted to do so.
Input a 4-digit code and press ENTER. Enter it
again and press ENTER to verify. If you make a
mistake before pressing ENTER, press CLEAR.
Select a rating from 1 to 8 usingthe A/V
buttons.
Rating 1-8: Rating one (1) has the most restrictions
and rating eight (8) is the least restrictive.
Unlock
If you select unlock, parental control is not active
and the disc plays in full.
ote
If you set a rating for the DVD/CD Receiver, all disc
scenes with the same rating or lower are played. Higher
rated scenes are not played unless an alternate scene
is available on the disc. The alternative must have the
same rating or a lower one. If no suitable alternative is
found, playback stops. You must enter the 4-digit pass-
word or change the rating level in order to play the disc.
Press ENTER to confirm your rating selection,
then press SET UP to exit the menu.
Password (Security Code)
You can enter or change password.
1 Select Password on the LOCK menu then press >.
2 Follow step 2 as shown left (Rating). “Change” or
“New” is highlighted.
3 Enter the new 4-digit code, then press ENTER.
Input it again to verify.
4 Press SET UP to exit the menu.
If you forget your Security Code
If you forget your security code you can clear it using
the following steps:
1 Input the 6-digit number “210499” on the setup menu
and the security code is cleared.
2 Enter a new code as described above.
ote
When “ ineuteasswo mmmm ” appears on the TV screen,
press STOP (IN) and then press SET UP to move to the
setup menu.
7
Country Code
Enter the code of the country/area whose standards
were used to rate the DVD-Video disc, based on the list
in the reference chapter.
Select “Country Code” on the LOCK menu, then
press №.
2 Follow step 2 as shown left (Rating).
J Select the first character using 4 / Y buttons.
Shift the cursor using P button and select the
second character using 4 / Y buttons.
Press ENTER to confirm your country code
selection.
Before Operation (Continued)
OTHERS
OTHERS
PBC » On
DivX(R) Registration » Select
с Move p> Select
PBC
Set Playback Control (PBC) to On or Off.
On: Video CDs with PBC are played according to the
PBC.
Off: Video CDs with PBC are played the same way
as
Audio CDs.
DivX(R) Registration 29
You can show the DivX DRM (Digital Right
Management) Registration code for your unit only.
Your registration code 15: XXXXXXXX
Please use this code to register this player with
the DivX(R) Video On Demand service.
This will allow you to rent and purchase videos
using the DivX(R) Video On Demand format.
To learn more go to vaww.divx.comávod
The Registration code is used for VOD (Video-On-
Demand) service agent. You can purchase or rental an
encrypt movie file.
otes
If you rent the DivX VOD file, it has several options of
viewing limits as show below.
* Display the number which you can watch the file.
(7) This rental video has 7 views left. A view
ends when you stop playback, play a different
video, or tum off your player.
Do you want to use one of your 7 views now
Yes
* The rental has been expired.
CO This rental is expired.
» Display the authorization error.
This video player is not authorized to
play this video.
“DVD or Video CD Operation
Playing a DVD and Video CD
Éd Playback Setup
e Turn on the TV and select the video input source con-
nected to the DVD/CD Receiver.
e Audio system: Turn on the audio system
and select the input source connected to the
DVD/CD Receiver.
1 Press OPEN/CLOSE (4) to open the disc tray.
Load your chosen disc in the tray, with the label
facing up.
When a double-sided DVD is inserted, make sure
the side you want to play is facing down.
Press OPEN/CLOSE (4) to close the tray.
READING appears on the TV screen, and playback
starts automatically. If playback does not start,
press PLAY.
In some cases, the disc menu might appear
instead.
Tf a menu screen is displayed
The menu screen may be displayed first after loading a
DVD or Video CD which contains a menu.
Use the </»>/4/Y buttons to select the title/chapter you
want to view, then press ENTER to start. Press TITLE
or DVD MENU to return to the menu screen.
Use the </»>/4/V buttons to select an option you
want, then press ENTER to view the option.
e Use the number buttons to select the track you want
to view.
Press RETURN to return to the menu screen.
e Menu setting and the exact operating procedures for
using the menu may differ depending on the disc.
Follow the instructions on the each menu screen.
You also may set PBC to Off under setup.
otes
e |f Parental Control is set and the disc is not within the
Rating settings (not authorized), the 4-digit code must
be entered and/or the disc must be authorized (see
“Parental Control”, on page 18).
e DVDs may have a region code.
e Your receiver will not play discs that have a region
code different from your receiver. The region code for
this player is 3 (three).
DVD or Video CD Operation (Continued)
General Features
ote
Unless stated otherwise, all operations described use
the remote control. Some features may also be
available on the Setup menu.
Moving to another TITLE/GROUP
When a disc has more than one title/group, you can
move to another title/group as follows:
e Press DISP., then press the appropriate numbered
button (0-9) to select a title number.
Moving to another CHAPTER/TRACK
CD CD
When a title on a disc has more than one chapter or a
disc has more than one track, you can move to another
chapter/track as follows:
e Press HE or PP briefly during playback to select
the next chapter/track or to return to the beginning of
the current chapter/track.
e Press 4d twice briefly to step back to the previous
chapter/track.
e To go directly to any chapter during DVD playback,
press DISP. Then, press AW to select the
chapter/track icon. Then, enter the chapter/track
number using the numbered buttons (0-9).
ote
For two-digit numbers, press the numbered buttons
(0-9) in rapid succession.
Slow Motion
Press SLOW -/+ during pause.
The receiver will enter SLOW mode.
Use the SLOW -/+ to select the required speed: «i
1/16, «UL 1/8, dl 1/4 or Al 1/2 (backward), or I»
1/16, I» 1/8, I» 1/4 or I» 1/2 (forward).
J To exit slow motion mode, press PLAY.
ote
Slow motion playback in reverse is not applicable for
Video CD.
Still Picture and Frame-by-frame playback
CD CD
Press PAUSE/STEP during playback.
The DVD/CD Receiver will now go into PAUSE
mode.
You can advance the picture frame-by-frame by press-
ing PAUSE/STEP repeatedly on the remote control.
Search
Press << or PP» during playback.
The DVD/CD Receiver will now go into SEARCH mode.
Press << or PP repeatedly to select the
required speed: 44X2, <<X4, 83, 44X16,
444X100 (backward) or PP X2, >» X4, »»X6,
DP>>X16, DP» X100 (forward).
With a Video CD, the Search speed changes:
OZ, TOA, AXE, 44X16 (backward) or
>> Х2, >>> Х4, >>> Х8, > X16 (forward).
J To exit SEARCH mode, press PLAY.
Repeat Cy
DVD-Video discs - Repeat Chapter/Title/Off
To repeat the currently playing chapter, press
REPEAT.
The Repeat Chapter icon appears on the TV screen.
To repeat the title currently playing, press
REPEAT a second time.
The Repeat Title icon appears on the TV screen.
To exit Repeat mode, press REPEAT a third
time.
The Repeat Off icon appears on the TV screen.
Video CDs - Repeat Track/All/Off
To repeat the track currently playing, press
REPEAT.
The Repeat Track icon appears on the TV screen.
To repeat the disc currently playing, press
REPEAT a second time.
The Repeat All icon appears on the TV screen.
To exit Repeat mode, press REPEAT a third
time.
The Repeat Off icon appears on the TV screen.
E ote
On a Video CD with PBC, you must set PBC to Off on
the setup menu to use the Repeat function. See page
19.
DVD or Video CD Operation (Continued)
General Features (continued)
Repeat A-B
To repeat a sequence in a title;
Press A-B at your chosen starting point.
A- appears briefly on the TV screen.
Press A-B again at your chosen end point.
A-B appears briefly on the TV screen, and the repeat
sequence begins.
J To cancel the sequence, press A-B.
Time Search
The Time Search function allows you to start playing at
any chosen time on the disc.
Press DISP. during playback. The on-screen dis-
play appears on the screen.
The Time Search box shows the elapsed playing time of
the current disc.
Within 10 seconds, press A/V to select the Time
Search icon in the on-screen display.
The “-:--:-- appears in the Time Search box.
Within 10 seconds, use the number buttons to
enter the required start time. Enter hours,
minutes, and seconds from left to right in the
box.
If you enter the wrong numbers, press CLEAR to remove
the numbers you entered. Then enter the correct num-
bers.
Within 10 seconds, press ENTER to confirm the
start time.
Playback starts from the selected time on the disc. If you
enter an invalid time, playback will continue from the current
point.
Marker Search
You can start playback from a memorized point. Up to
nine points can be memorized.
To enter a mark, follow these steps.
1 During disc playback, press MARKER when
playback reaches the spot that you want to
memorize.
The marker icon will appear on the TV screen briefly.
Repeat step 1 to enter up to nine Marker points
on a disc.
To Recall a Marked Scene
1 During disc playback, press SEARCH.
The MARKER SEARCH menu will appear on the screen.
Within 10 seconds, press > to select a marker
number that you want to recall.
de ENTER.
Playback will start from the Marked scene.
To remove the MARKER SEARCH menu, press
SEARCH.
To clear a Marked Scene
1 During disc playback, press SEARCH.
The MARKER SEARCH menu will appear on the screen.
Press 4» to select the marker number that you
want to erase.
Js CLEAR.
The marker number will be erased from the list.
4 Repeat steps 2 and 3 to erase additional marker
numbers.
Br remove the MARKER SEARCH menu, press
SEARCH.
Zoom ED E CD CD E73
The Zoom function allows you to enlarge the video
image and to move through the enlarged image.
1 Press ZOOM during playback or still playback to
activate the Zoom function.
If you press ZOOM repeatedly, the magnification level
increases up to four steps.
100% size — 400% size — 800% —
1600% size — 100% size
2° the <> 4 Y buttons to move through the
zoomed picture.
ote
The zoom function may not work for some DVDs.
ww
DVD or Video CD Operation (Continued)
Special DVD Features
Checking the contents of DVD Video
discs: Menus
DVDs may contain menus that allow you to access
special features. To use the disc menu, press MENU.
Then, press the appropriate number button to select an
option. Alternatively, use the 4» /A/¥ buttons to high-
light your selection, then press ENTER.
Title Menu
Press TITLE.
If the current title has a menu, the menu will appear on
the screen. Otherwise, the disc menu may appear.
The menu can list camera angles, spoken lan-
guage and subtitle options, and chapters for the
title.
Disc Menu
Press MENU,
The disc menu is displayed.
Changing the Audio Language
Czy
Press AUDIO repeatedly during playback to hear a
different audio language or audio track.
Changing the Audio Channel
Press AUDIO repeatedly during playback to hear a
different audio channel (STER., LEFT or RIGHT).
ote
If @ appears, the feature is not available on the disc.
Subtitles es
Press S-TITLE repeatedly during playback to see the
different subtitle languages.
otes
e The subtitle file of the DivX file is displayed only smi,
srt and sub.
e |! there is no information or there is a code that can
not read in the DivX file, “1/1” etc are displayed.
DVD Audio Discs
DVD Audio is a new disc format building on the success
of DVD to provide high quality, uncompressed, multi-
channel audio for a new experience in audio quality. A
DVD Audio disc can be identified by the DVD audio logo
on the disc jacket or on the disc itself.
DVD Audio can provide higher quality stereo than Audio
CDs with a sampling rate of up to 192kHz (compared to
44 1kHz for CDs). DVD Audio digital sound can be
delivered with up to 24 bits of data (compared to 16 bits
for a standard CD).
vv
A typical DVD Audio disc contains up to seven times the
data capacity of a CD. This additional space is used for
music, either Advanced Resolution multi-channel sound
quality that is closer to the artists master recording or
for longer recordings. Many DVD Audio discs contain
on-screen text, such as artist biographies, playlists, or
lyrics. Some DVD Audio discs contain photo galleries or
video clips.
ote
To enjoy maximum sound quality and surround effect of
DVD Audio, you must use 5.1 channel analog audio
output (5.1CH AUDIO OUT jacks on the DVD/CD
receiver). If you use the DIGITAL OUT (OPTICAL or
COAXIAL) for your audio connection, the sound will
only be similar to CD-quality sound even though youre
playing a DVD Audio disc.
#3) ‹
Some DVD Audio discs divide content into different
groups. Your player enables you to quickly access
different groups during playback via the on-screen
display.
Moving to another GROUP 1/2» |
1. Press DISP. during playback on in stop mode.
2. Press A/V to select Group icon.
3. Press 4» or the numbered buttons (0-9) to select a
group humber.
Note:
Sometimes the author of the disc creates hidden
content that can only be accessed by entering a pass-
word. If the lock icon appears on the TV screen, enter
the password (sometimes you'll find it on the disc's
jacket cover or on a web site). This password control
isn't dictated by your DVD/CD receiver — it is a function
of the disc.
Since the authoring of DVD Audio Discs varies, some of
the on-screen display choices might not be available for
the disc you're playing.
Viewing another PAGE [EX < Шо
Since DVD Audio discs can hold a lot of content, there
are various ways to see what's available on the disc.
1. Press DISP. during playback.
2. Press AW to select Page icon.
3. Press 4» to select a page number.
What appears on the screen will vary from disc to
disc because the information available depends upon
the way the disc was created.
Note:
Since the authoring of DVD Audio Discs varies, some of
the on-screen display choices might not be available for
the disc you're playing.
Audio CD or MP3/WMA Disc Operation
Playing an Audio CD and MP3/ WMA
Disc ED CDB CID
The DVD/CD Receiver can play MP3/WMA formatted
recordings on CD-ROM, CD-R, or CD-RW discs.
Audio CD
Once you insert an audio CD a menu appears on the
TV screen. Press À / V to select a track then press
PLAY or ENTER and playback starts.
| oo0o0 J3 1/12
Audio CD
Eo
E
NI
ee |
”
5151515151515 8
ooo oo ooo
SUELE ELEIENSÍE
1 =
o
MP3 / WMA
1. Press À / V to select a folder, and press ENTER to
see the folder contents.
2. Press A/ Vio select a track then press PLAY or
ENTER. Playback starts.
otes
e |f you are in a file list on the MP3/WMA menu and want
to return to the Folder list, use the 4 / Y to highlight
Æ]. and press ENTER.
e Press MENU to move to the next page.
e On a CD with MP3/WMA file and JPEG file, you can
switch MP3/WMA and JPEG menu. Press TITLE and
MP3/WMA or JPEG word on top of the menu is high-
lighted. Then, use < / P to select MP3/WMA or JPEG
then press ENTER.
Pause ED CD CID
1 Press PAUSE/STEP during playback.
2 To return to playback, press PLAY or press
PAUSE/STEP again.
Moving to another Track CCD CI CID
e Press HE or DPI briefly during playback to go to the next
track or to return to the beginning of the current track.
e Press tE twice briefly to step back to the previous track.
e In case of audio CD, to go directly to any track, enter
the track number using the numbered buttons (0-9)
during playback.
Repeat Track/All/Off CE CID CT
You can play a title/chapter/all/track on a disc.
1 Press REPEAT when playing a disc. The repeat icon
appears.
2 Press REPEAT to select a desired repeat mode.
* TRACK: repeats the current track
* ALL: repeats all the tracks on a disc.
* Off(No display): does not play repeatedly.
Search ED EII CI
1 Press << or >>» during playback.
The receiver will now go into SEARCH mode.
2 Press «<< or PP repeatedly to select the required
speed: 44X2, 44X4, AXE (backward) or »»X2,
DD X4, >» X8 (forward).
3 To exit SEARCH mode, press PLAY.
MP3 / WMA disc compatibility with this player is
limited as follows:
* Sampling frequency: within 32 - 48 kHz (MP3),
Within 24 - 48kHz (WMA)
* Bit rate: within 8 - 320kbps (MP3),
32- 192kbps (WMA)
* The DVD/CD Receiver cannot read an MP3/WMA
file that has a file extension other than “mp3” /
“wma”.
* CD-R physical format should be ISO 9660
e |f you record MP3 / WMA files using software that
cannot create a file system (eg. Direct-CD) it is
impossible to playback MP3 / WMA files. We
recommend that you use Easy-CD Creator, which
creates an ISO 9660 file system.
* File names should have a maximum of 8 letters and
must incorporate an .mp3 or .wma extension.
* They should not contain special letters such as /?
* <> etc.
* The total number of files on the disc should be less
than 999.
This DVD/CD Receiver requires discs and recordings
to meet certain technical standards in order to
achieve optimal playback quality. Pre-recorded DVDs
are automatically set to these standards. There are
many different types of recordable disc formats
(including CD-R containing MP3 or WMA files) and
these require certain pre-existing conditions (see
above) to ensure compatible playback.
Customers should note that permission is
required in order to download MP3 / WMA files
and music from the Internet. Our company has no
right to grant such permission. Permission should
always be sought from the copyright owner.
ww
“JPEG Disc Operation
Viewing a JPEG disc
This unit can play discs with JPEG files.
Before playing JPEG recordings, read the notes on
JPEG Recordings on right.
Insert a disc and close the tray.
The JPEG menu appears on the TV screen.
5
| e
EQ List
JPEG Folder 1
LI JPEG Folder 2
(OI JPEG Folder 3
id
id
id
_1JPEG Folder 4
JPEG Folder 6
LI JPEG Folder 7
LI JPEG Folder 8
ВЕЛЕЛ
@ |@ | @ |2 | @ | @
LID
ola
Press A / V to select a folder, and press ENTER.
A list of files in the folder appears.
If you are in a file list and want to return to the
previous Folder list, use the 4 / Y buttons on the
remote to highlight ©. and press ENTER.
If you want to view a particular file, press A/V
to highlight a file and press ENTER or PLAY.
While viewing a file, you can press STOP to move
to the previous menu (JPEG menu).
Ed ips
* There are four Slide Speed options E :
> (Slow), >> (Normal), >>> (Fast) and II (off).
Use A/V/<4/» to highlight the Speed. Then, use «4 / » to
select the option you want to use then press ENTER.
* If you set Speed option to Off, Slide is not active.
SLIDE SHOW
Use A Y < P to highlight the EX (Slide Show) then
press ENTER.
STILL PICTURE
1. Press PAUSE/STEP during slide show.
The DVD/CD Receiver will now go into PAUSE
mode.
2. To return to the slide show, press PLAY or press
PAUSE/STEP again.
MOVING TO ANOTHER FILE
Press SKIP (kt or PP) once while viewing a picture
to advance to the next or previous file.
TO ROTATE PICTURE
Press < / » during showing a picture to rotate the
picture clockwise or counter-clockwise.
©
JPEG disc compatibility with this player is limited
as follows:
* Depending upon the size and number of JPEG
files, it could take a long time for the DVD/CD
Receiver to read the disc's contents. If you don't
see an on-screen display after several minutes,
some of the files may be too large — reduce the
resolution of the JPEG files to less than 2760 x
2048 pixels and burn another disc.
* The total number of files and folders on the disc
should be less than 999.
* Some discs may be incompatible due to a different
recording format or the condition of disc.
* Ensure that all the selected files have the “jpg”
extensions when copying into the CD layout.
* |f the files have “.jpe” or “.jpeg” extensions, please
rename them as “.ipg” file.
* File names without “.jpg” extension will not be able
to be read by this DVD/CD Receiver. Even though
the files are shown as JPEG image files in
Windows Explorer.
Programmed Playback €=B €=2 CD
The program function enables you to store your favorite tracks from any disc in the receiver memory. A program can
contain 300 tracks.
1 Insert a disc. REPEAT PROGRAMMED TRACKS
1. Press REPEAT when playing a disc. The repeat
Audio CD and MP3/WMA Discs:
icon appears.
Audio CD or MP3/WMA menu appears as below.
2. Press REPEAT to select a desired repeat mode.
* TRACK: repeats the current track
* ALL: repeats all the tracks on programmed list.
* Off(No display): does not play repeatedly.
ERASING A TRACK FROM “PROGRAM”
LIST
Audio CD Menu MP3/WMA Menu 1. Use A V to select the track that you wish to erase
from the Program list.
FD
a
am
A
=|=|=|=1=|=|=[514
0: O0: O0 1712
Audio CD
o Le
-
Select a track on the “List”, then press PROGRAM
or select “ 1” (Add)" icon then press ENTER to 2. Press CLEAR. Alternatively, select “ “i (Delete)
place the selected track on the “Program” list. icon then press ENTER to place the selected track
Repeat to place additional tracks on the list. on the Program list. Repeat to erase additional
EA ote tracks on the list.
You can add all tracks in the disc. Select “n= (Add All)” icon
then press ENTER. ERASING THE COMPLETE PROGRAM
LIST
Select the track you want to start playing on the ; y
“Program” list. Press MENU to move to the next Use A / Y to select “ “sm (Del all)”, then press ENTER.
age.
pay E ote
Press PLAY or ENTER to start. Playback begins in The programs are also cleared when the disc is removed.
the order in which you programmed the tracks.
Playback stops after all of the tracks on the
“Program” list have played once.
To resume normal playback from programmed play-
back, select a track of AUDIO CD (or MP3/WMA)
list and then press PLAY.
DivX Disc Operation
Using this DVD/CD Receiver you can play DivX disc.
Insert a disc and close the tray. The DivX menu
appears on the TV screen.
_] Movie Folder 1
©] Movie Folder 2
©] Movie Folder 3
©] Movie Folder 4
©] Movie Folder 5
C] Movie Folder 6
I] Movie Folder 7
D] Movie Folder 8
Press A / V to select a folder, and press ENTER. À
list of files in the folder appears. If you are in a file
list and want to return to the Folder list, use the
A / Y buttons on the remote to highlight 1. and
press ENTER.
If you want to view a particular file, press A / V to
highlight a file and press ENTER or PLAY.
A Press STOP to exit.
otes
* Be sure to select “SUBTITLE ON” mode before playback a
DivX file by pressing ENTER every time.
* When the subtile has more than two languages in the file,
original subtile is only available.
* The Pro logie II Sound mode is not available for DivX file.
+ Subtitle in Chinese will not be displayed during playback а
DivX file. (Subtitle in English is available)
The DivX files in your memory card will not be able to be
play.
DivX disc compatibility with this player is limited
as follows:
* Available resolution size of the DivX file is under
720x576 (W x H) pixel.
* The file name of the DivX subtitle is available by
20~40 characters (different by language).
* If there is impossible code to express in the DivX
file, it may be displayed as " _ " mark on the dis-
play.
* If the number of the screen frame is over 30 per
1 second, this unit may not operate normally.
If the video and audio structure of recorded file
is not interleaved, either video or audio is out-
putted.
If the file is recorded with GMC, the unit sup-
ports some of 1-point of the record level.
+ GMC?
GMC is the acronym for Global Motion Compensation. It
is an encoding tool specified in MPEG4 standard. Some
MPEG4 encoders, like DivX or Xvid, have this option.
There are different levels of GMC encoding, usually called
1-point, 2-point, or 3-point GMC.
Playable DivX file
O "avi " "mpg " “mpeg и
Playable Codec format
@ "DIVX3.xx ", "DIVX4.xx ", "DIVX5.xx ", "XVID ",
"MP43 ", "3IVX ", "MP42 ".
Playable Audio format
@ "AC3 ", "DTS ", "PCM ", "MP3 ", "WMA".
* Sampling frequency: within 32 - 48 kHz (MP3),
Within 24 - 48kHz (WMA)
* Bit rate: within 32 - 320kbps (MP3),
40 - 192kbps (WMA)
“Speaker Setup
Adjust the following settings for the built-in 5.1 channel
surround decoder.
Press SET UP.
The setup menu appears.
Use A / V to select the AUDIO option then press
P to Move to the second level.
Use À / V to select the Speaker Setup option
then press > to move to the third level. “Select”
is highlighted.
Press ENTER and 5.1 Speaker Setup menu
appears.
Cord Frontl DD» =
Volume
Distance 2 | m
Test off 7
Size Small | =
0 Е D e &
$
© Enter
4) select SS Move 5» Return
5 Use < / P to select the desired speaker.
6 Adjust options using 4 / Y / </ P buttons.
Press ENTER to confirm your selection. The
unit returns to the previous menu.
Speaker
Select a speaker that you want to adjust.
(Front speakers (Left), Front speakers (Right), Center
Speaker, SubWoofer, Rear speakers (Left), or Rear
speakers (Right))
ote
Certain speaker settings are prohibited by the Dolby
Digital licensing agreement.
Size
Since the speaker settings are fixed, you cannot change
them.
Volume
Press «< / P to adjust the output level of the selected
speaker. (-5dB - +5dB)
Distance
If you connected speakers to your DVD/CD Receiver,
setting the distance lets the speakers know how far the
sound has to travel to reach your set listening point.
This allows the sound from each speaker to reach the
listener at the same time.
Press 4 / № 10 adjust the Distance of the selected
speaker.
ote
You can adjust the distance of Center speaker and Rear
speakers (left & right) only.
Test
Press < / P to test the signals of each speaker.
Adjust the volume to match the volume of test signals
memorized in the system.
Front Left (L) — Center — Front Right (R) >
Rear Right (R) — Rear Left (L) > SubWoofer
Additional Information
Last Condition Memory
This DVD/CD Receiver memorizes the user settings for
the last disc that you have viewed. Settings remain in
memory even if you remove the disc from the player or
switch off the player. If you load a disc that has its set-
tings memorized, the latest stop position is automatical-
ly recalled.
otes
e Settings are stored in memory for use any time.
e This DVD/CD Receiver does not memorize settings of
a disc if you switch off the DVD/CD Receiver before
commencing to play it.
Screen Saver
The screen saver appears when you leave the DVD
player in Stop mode for about five minutes.
System Select
You must select the appropriate system mode for your
TV system. If NO DISC appears in the display window,
press and hold P/STEP on the front panel or remote
control for more than 5 seconds to be able to select a
system (PAL, NTSC or AUTO).
e When the selected system does not coincide with the
system of your TV, normal colour picture may not be
displayed.
Select when DVD/CD Receiver is connected
with Multi system TV.
AUTO:
NTSC: Select when DVD/CD Receiver is connected
with NTSC-TV.
PAL: Select when DVD/CD Receiver is connected
with PAL-TV.
Controlling the TV
Your remote control is capable of operating your
DVD/CD Receiver as well as limited functions of LG TV.
Follow the instructions below to operate for your LG TV.
Before using the remote control, press the TV to
select the device to be operated.
To switch the remote control mode (to operate a
different device), be sure to press the TV first.
The POWER, CH(VY/4), VOLUME (+/-), and INPUT
buttons on remote control are used to operate the
LG TV.
Setting Remote Control Codes for LG TV
e Hold POWER and press PR/CH(+/-) (Y/4) button
repeatedly until the TV on or off.
ote
If the remote control does not operate your particular
TV, try the other code or use the remote control
originally supplied with the LG TV. (LG and Gold Star)
Due to the variety of codes used by manufacturers,
OUR COMPANY cannot guarantee that the remote
control will operate every model of LG TV.
“Operation with Radio
Presetting the radio stations
You can preset 50 stations for FM and AM (MW). Before
tuning, make sure that you have turned down the vol-
ume.
Press BAND on the remote control until FM or
AM (MW) appears in the display window.
And then every time you press BAND, FM and
AM (MW) changes alternately.
Press and hold TUNING |<< «+<or >> >> on
the front panel for about two seconds until the
frequency indication starts to change, then
release.
Scanning stops when the DVD/CD Receiver tunes in a
station. “TUNED” and “STEREO?” (for stereo program)
appear in the display window.
Press PROG. MEMO. on the remote control.
A preset number will flash in the display window.
Press PR (A/V) on the remote control to select
the preset number you want.
Press PROG./MEMO. on the remote control
again.
The station is stored.
7 Repeat steps 3 to 6 to store other stations.
To tune in a station with a weak signal
Press TUNING Hd << or >> >> repeatediy in step 3
to tune in the station manually.
To clear all the stored stations
Press and hold PROG./MEMO. for about two seconds
and “CLEAR ALL” is appeared in the display window
and then press PROG./MEMO. again, the stations are
cleared.
e If you have accidentally entered into the “CLEAR ALL”
and you do not wish to clear the memory, do not
press any key. After a few seconds, the “CLEAR ALL”
display will go off by itself and change to mode.
ote
If all stations have already been entered, the FULL
message will appear in the display window for a
moment and then a preset number will flash.
To change the preset number, follow the steps 5-6 as
above.
Listening to the radio
Preset radio stations in the DVD/CD Receiver's memory
first (see “Presetting radio stations” on the left).
Press BAND until AM (MW) or FM appears in the
display window.
The last received station is tuned in.
Press PR(A/V) repeatedly on the remote control
to select the preset station you want.
Each time you press the button, the DVD/CD Receiver
tunes in one preset station at a time.
Adjust the volume by rotating VOLUME on the
front panel or by pressing VOLUME + or - on the
remote control repeatedly.
To turn off the radio
Press POWER to turn the DVD/CD Receiver off or
select another function mode (DVD/CD, AV 1, etc.)).
To listen to non-preset radio stations
e Use manual or automatic tuning in step 2.
e For manual tuning, press TUN(-) < or TUN (+) > on
the remote control repeatedly.
e For automatic tuning, press and hold TUN(-) < or
TUN (+) > for about two seconds on the remote
control.
To select a preset radio station directly
You can use the number buttons on the remote control
to select a preset radio station directly.
For example, to listen to preset station 4, press 4 on the
remote control. To listen to preset station 19, press 1
then 9 (within 3 seconds).
For your reference
e If an FM program is noisy
Press MONO/ST. on the front panel so that
"STEREO" disappears in the display window.
There will be no stereo effect, but the reception will
improve. Press the button again to restore the stereo
effect.
e To improve reception
Reorient the supplied antennas.
Other Functions
Sleep Timer Setting
You can set the DVD/CD Receiver to turn off automati-
cally at a specified time.
Press SLEEP to set the desired sleep time.
The SLEEP indicator and sleep time appears in the dis-
play window.
Each time you press SLEEP the setting changes
in the following order.
SLEEP 180 — 150 — 120 — 90 —80 — 70 — 60 — 50 —
40 — 30 — 20 —10 — OFF
ote
e You can check the time remaining before the
DVD/CD receiver turns off.
Press SLEEP. The remaining time appears in the
display window.
Dimmer
This function will change the brightness of the display
window on the front panel during in power-on status.
Press the DIMMER repeatedly.
Mute
Press MUTE to mute your unit.
You can mute your unit in order, for example, to answer
the telephone, “MUTE” indicator flashes in the display
window.
Using the Headphone Jack
Connect a stereo headphone plug (¢3.5mm) into the
PHONES connector.
The speakers are automatically disconnected when you
plug in a headphone (hot supplied).
Selecting the Input Source
You can use VCRs or other units connected to the AV 1
IN, AV 2 IN or Optical connector. Refer to the owner's
manual supplied with the unit for further information on
the operation.
Press AUX and D.INPUT repeatedly on the remote
control to select the desired input source.
Each time you press this button, the mode of the func-
tion changes in the following sequence:
e AV 1: for selecting the analog signal from AV1 AUDIO IN
(L/R) & VIDEO IN Connectors.
e AV 1 OPT: for selecting the optical digital signal from AV1
VIDEO IN & OPTICAL IN Connector.
e AV 2: for selecting the analog signal from AV2 AUDIO IN
(L/R) & VIDEO IN Connectors.
e AV 2 OPT: for selecting the optical digital signal from AV2
VIDEO IN & OPTICAL IN Connector.
otes
e The Optical input function is available only when the
other unit's Sampling Frequency is 32 ~ 96kHz.
e You can also select the input source by pressing
FUNC. button on the front panel.
©
XTS (Excellent True Sound)
You can enjoy the vivid stereophonic sound of the
digital original source without any signal distortion.
Each time you press XTS during 2 channel mode,
the setting changes in the following order.
XTS- 1 — XTS- 2 — XTS- 3 — NORMAL …
Tips:
e XIS- 1: When playing the movie with the weak bass
sound relatively to the general music, it
enforces the sense of sound at woofer
for you to satisfy with.
In the mode of 2 CH BYPASS, It creates the
high display effect by playing the sound
source via the rear speakers same as the
front speakers.
e XIS-3: You can operate both XTS- 1 and XTS- 2
simultaneously and it can complement the
relative degrading of the sound pitch of the
woofer at the XTS- 2 mode.
e XIS-2:
ote
e The XTS- 2 mode is temporarily disabled when changing
from 2.1 CH to 5.1 CH and it is enabled when changing it to
2.1 CH,
XTS pro
The unique sound quality of the LG Technology creates
the optimum sound for you to play the perfect playback
of the original sound and to feel the living sound source.
Each time you press XTS pro the setting changes in
the following order.
XTS-P ON — XTS-P OFF
Language Codes
Use this list to input your desired language for the following initial settings:
Disc Audio, Disc Subtitle, Disc Menu.
Language Code Language Code Language Code Language Code
Abkhazian 6566 Finnish 7073 Macedonian 7775 Slovenian 8376
Afar 6565 French 7082 Malagasy 7771 Somali 8379
Afrikaans 6570 Galician 7176 Malay 7783 Spanish 6983
Albanian 8381 Georgian 7565 Malayalam 7776 Sudanese 8385
Ameharic 6577 German 6869 Maltese 7784 Swahili 8387
Arabic 6582 Greek 6976 Maori 7773 Swedish 8386
Armenian 7289 Greenlandic 7576 Marathi 7782 Tagalog 8476
Assamese 6583 Guarani 7178 Moldavian 7779 Tajik 8471
Azerbaijani 6590 Gujarati 7185 Mongolian 7778 Tamil 8465
Bashkir 6665 Hausa 7265 Nauru 7865 Tatar 8484
Basque 6985 Hebrew 7387 Nepali 7869 Telugu 8469
Bengali; Bangla 6678 Hindi 7273 Norwegian 7879 Thai 8472
Bhutani 6890 Hungarian 7285 Oriya 7982 Tibetan 6679
Bihari 6672 Icelandic 7383 Panjabi 8065 Tigrinya 8473
Breton 6682 Indonesian 7378 Pashto, Pushto 8083 Tonga 8479
Bulgarian 6671 Interlingua 7365 Persian 7065 Turkish 8482
Burmese 7789 Irish 7165 Polish 8076 Turkmen 8475
Byelorussian 6669 Italian 7384 Portuguese 8084 Twi 8487
Cambodian 7577 Japanese 7465 Quechua 8185 Ukrainian 8575
Catalan 6765 Javanese 7487 Rhaeto-Romance 8277 Urdu 8582
Chinese 9072 Kannada 7578 Rumanian 8279 Uzbek 8590
Corsican 6779 Kashmiri 7583 Russian 8285 Vietnamese 8673
Croatian 7282 Kazakh 7575 Samoan 8377 Volapük 8679
Czech 6783 Kirghiz 7589 Sanskrit 8365 Welsh 6789
Danish 6865 Korean 7579 Scots Gaelic 7168 Wolof 8779
Dutch 7876 Kurdish 7585 Serbian 8382 Xhosa 8872
English 6978 Laothian 7679 Serbo-Croatian 8372 Yiddish 7473
Esperanto 6979 Latin 7665 Shona 8378 Yoruba 8979
Estonian 6984 Latvian, Lettish 7686 Sindhi 8368 Zulu 9085
Faroese 7079 Lingala 7678 Singhalese 8373
Fiji 7074 Lithuanian 7684 Slovak 8375
Country Codes
Choose a country code from this list.
Country Code Country Code Country Code Country Code
Afghanistan AF Ethiopia ET Malaysia MY Saudi Arabia SA
Argentina AR Fiji FJ Maldives MV Senegal SN
Australia AU Finland FI Mexico MX Singapore SG
Austria AT France FR Monaco MC Slovak Republic SK
Belgium BE Germany DE Mongolia MN Slovenia Si
Bhutan BT Great Britain GB Morocco MA South África ZA
Bolivia BO Greece GR Nepal NP South Korea KR
Brazil BR Greenland GL Netherlands NL Spain ES
Cambodia KH Islands HM Dutch Antilles AN Sri Lanka LK
Canada CA Hong Kong HK New Zealand NZ Sweden SE
Chile CL Hungary HU Nigeria NG Switzerland CH
China CN India IN Norway NO Taiwan TW
Colombia CO Indonesia ID Oman OM Thailand TH
Congo CG Israel IL Pakistan PK Turkey TR
Costa Rica CR Italy IT Panama PA Uganda UG
Croatia HR Jamaica JM Paraguay PY Ukraine UA
Czech Republic CZ Japan JP Philippines PH United States US
Denmark DK Kenya KE Poland PL Uruguay UY
Ecuador EC Kuwait KW Portugal PT Uzbekistan UZ
Egypt EG Libya LY Romania RO Vietnam VN
El Salvador SV Luxembourg LU Russian Federation RU Zimbabwe ZW
“Troubleshooting
Check the following guide for the possible cause of a problem before contacting service.
Symptom
Cause
Correction
No power.
The power cord is disconnected.
Plug the power cord securely into the
wall outlet.
The power is on, but
the DVD/CD Receiver
does not work.
No disc is inserted.
Insert a disc. (Check that the DVD or,
audio CD indicator in the DVD display is
lit.)
No picture.
The TV is not set to receive DVD signal
output.
Select the appropriate video input mode
on the TV so the picture from the DVD/
CD Receiver appears on the TV screen.
The video cable is not connected
securely.
Connect the video cable into the jacks
securely.
The connected TV power is turned off.
Turn on the TV.
There is no sound or
only a very low-level
sound is heard.
The equipment connected with the
audio cable is not set to receive DVD
signal output.
Select the correct input mode of the
audio receiver so you can hear the
sound from the DVD/CD Receiver.
The audio cables are not connected
securely.
Connect the audio cable into the jacks
securely.
The power of the equipment connected
with the audio cable is turned off.
Turn on the equipment connected with
the audio cable.
The audio connecting cable is damaged.
Replace it with a new one.
The playback picture is
poor.
The disc is dirty.
Clean the disc.
The DVD/CD Receiver
does not start playback.
No disc is inserted.
Insert a disc. (Check that the DVD, or
audio CD indicator in the DVD display is
lit.)
An unplayable disc is inserted.
Insert a playable disc. (Check the disc
type, colour system and Regional code.)
The disc is placed upside down.
Place the disc with the playback side
down.
The disc is not placed within the guide.
Place the disc on the disc tray correctly
inside the guide.
The disc is dirty.
Clean the disc.
A menu is on the TV screen.
Press the SET UP button to turn off the
menu screen.
The Rating level is set.
Cancel the Rating function or change
the rating level.
Loud hum or noise is
heard.
The plugs and jacks are dirty.
Wipe them with a cloth slightly mois-
tened with alcohol.
The disc is dirty.
Clean the disc.
The speakers and components are
connected poorly.
Connect the speakers and components
securely.
The DVD/CD Receiver is located too
close to the TV.
Move your TV away from the audio
components.
">