INSTALLATION INSTRUCTIONS
BUILT-IN GAS AND ELECTRIC
RECESSED WALL OVENS
700 SERIES PIPING
AND INSTALLATION
NOTE: DO NOT INSTALL
BELOW WORK COUNTER
CABINET CUTOUT
EY М
iz
“E, E
- 234 —
|
18" MIN.
26" SUGGESTED
TO FLOOR
— 4 1/8" TO FRONT
OF CABINET
3" FROM INSIDE EDGE
OF CABINET CUTOUT
<<
1/4" NIPPLE LENGTH
AS NEEDED
(HOUSE PIPING)
APPLIANCE SHUT-OFF
VALVE AND
REGULATOR ASSY.
MALE ADAPTER
1/2" N.P.T.
HOUSE PIPING
NOTE
THE REGULATOR AND SHUT-OFF VALVE
ASSEMBLY MUST BE ACCESSIBLE AND
USED WITH THIS APPLIANCE.
ELECTRICAL
CONNECTION
CABINET SPACER
(4) REQ'D
= оне hm a em a ооо МО.
HOUSE PIPING, FLEX
CONNECTOR OR IRON
PIPE AND SHUT-OFF
AS REQ'D PER CODE
STANDARD 24" CABINET |
SAVE THESE INSTRUCTIONS
GAS RECESSED WALL OVEN
Slide the oven unit into the cabinet recess as shown in the diagram. Secure the oven
unit to the cabinet with wood screws. Be sure to use the cabinet spacer with the wood
screw as a “washer” between the wood cabinet and the oven front frame.
The recess in which the oven is installed shall be constructed so as to provide a
complete closure around the recessed portion of the unit and any openings around
gas and electrical service outlets MUST be closed at time of installation. The
installation must conform with local codes. In the absence of local codes, the
National Fuel Gas Code Z223.1 latest edition.
A MANUAL GAS VALVE MUST BE INSTALLED IN AN ACCESSIBLE LOCATION IN
THE GAS LINE EXTERNAL TO THE UNIT FOR THE PURPOSE OF TURNING ON
OR SHUTTING OFF GAS TO THE UNIT.
WARNING
ELECTRICAL GROUNDING
INSTRUCTIONS
This appliance is equipped with a three prong
grounding plug for your protection against
shock hazard and should be plugged directly GROUND AA
into a properly grounded receptacle. Do not cut BEFORE USE.
or remove the grounding prong from this plug.
ELECTRIC RECESSED WALL OVEN
With the oven positioned in front of the cabinet opening, connect the leads extending
from the conduit to the junction box.
Check all connections to see that they are tight and have not become loosened during
transit.
After the above mentioned wire connections have been made at the junction box,
secure the oven unit to the cabinet with wood screws. Be sure to use the cabinet
spacer with the wood screw as a “washer” between the wood cabinet and the oven
front frame.
POWER CONNECTIONS TO APPLIANCES
We suggest that you have the dealer where you purchased your new oven unit install
it or have him arrange installation by a qualified electrician. Installation must conform
with local codes. In addition, installation must conform with the National Electric Code
NFPA70 latest edition.
WARNING-Be sure electric power is OFF at the fuse (breaker) box until the unit is
installed and ready to operate. See appliance rating plate for maximum
K.W. and amperage ratings.
INSTALLATION
It is the responsibility of your installer to make certain that your oven unit is properly
installed. Situations caused by improper installations are not covered under the
warranty. Any expenses incurred due to such situations will not be paid by the
manufacturer of the appliance.
WIRING DIAGRAM FOR GAS SURFACE UNITS
AND WALL OVENS
TOP BURNER
K IGNITION SWITCHES
$ $
LA à LA
=
= = = ==
IGNITION IGNITION MODULE
LEAD LEAD R
E
R W
E NG
OVEN T'STAT
BK W
AC
aK | | IGNITOR — SAFETY VALVE
re
CLOCK WITH TIME
BK @) (NH
OVEN LAMP SWITCH \_“/ OVEN LAMP
WALL Jef
вк PLUG u
. =
REFER ONLY TO FEATURES WHICH ARE EQUIPPED ON YOUR RANGE
WARNING-ELECTRICAL GROUNDING INSTRUCTIONS:
THIS APPLIANCE IS EQUIPPED WITH A THREE-PRONG GROUNDING PLUG FOR YOUR PROTECTION
AGAINST SHOCK HAZARD AND SHOULD BE PLUGGED DIRECTLY INTO A PROPERLY GROUNDED
THREE-PRONG RECEPTACLE. DO NOT CUT OR REMOVE THE GROUNDING PRONG FROM THE PLUG.
180-6C89 REV. 1
FLEXIBLE CONNECTORS - if the gas range/oven is connected to a gas supply with a
metal flexible connector, move the range/oven with CAUTION for service or cleaning.
Flexible connectors are not intended for repeated bending. Do not allow cleaners to make
contact with flexible connectors.
The connector and its fittings are designed for use only on the original
installation and are not to be reused for another appliance or at another location.
Connectors must comply with ANSI 221.24.
WIRING DIAGRAM FOR ELECTRIC RANGES
la
| —…— =
J LM
CLOCK FOR TIMES OVEN
IN MANUAL POSITION
: EN
THERMOSTAT г.
[awe © INDICATOR |
|
BAKE
LO ELEMENT
| SWITCH
1
(A) 18
(NM 18
® 16
D) 16
rote + ‘ет
CLOCK WITH TIMER
ге’ CB g Og {
OVEN LAMP
GN
GAUGE CODE
© 14
(P) 14
INDICATOR
LIGHT
| «+
LIGHT
— — —
“GROUND NOTICE
WARNING:
FRAME GROUNDED TO NEUTRAL OF
APPLIANCE THROUGH A LINK. IF USED IN
A MOBILE HOME OR IF LOCAL CODES DO
NOT PERMIT GROUNDING THROUGH THE
NEUTRAL, DISCONNECT THE LINK FROM
THE NEUTRAL AND USE GROUNDING
TERMINAL OR LEAD TO GROUND UNIT IN
ACCORDANCE WITH LOCAL CODES.
CONNECT NEUTRAL TERMINAL OR LEAD
TO BRANCH CIRCUIT NEUTRAL IN USUAL
MANNER. CONSULT MANUFACTURER'S
INSTRUCTIONS WHEN CODES REQUIRE
THAT 3-CONDUCTOR CORD ASSEMBLIES
MUST BE REPLACED BY 4-CONDUCTOR
CORD ASSEMBLIES.
SEE RATING PLATE FOR
TOTAL WATTAGE & VOLTAGE
REFER ONLY TO FEATURES
WHICH ARE EQUIPPED ON
YOUR RANGE
USE COPPER WIRE ONLY
184-6C076 REV. 3
PART NO. 180-6C128
* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project
advertisement
© 2021