EDNord - Konica Minolta PagePro 1250W Laserprinter

EDNord - Konica Minolta PagePro 1250W Laserprinter
PagePro 1250W Setup Guide
Before setting up the printer, see the safety information in the User’s Guide, included in PDF format on the
Utilities and Documentation CD-ROM.
1
Remove the Packing Materials
Keep all of the packing materials in case you ever
need to move the printer.
3
Install Optional Accessories
If you purchased a lower feeder unit and/or face-up
output tray, install them now. Instructions are included
in the User’s Guide (in PDF format on the Utilities and
Documentation CD-ROM).
4
Set up the Printer
■ Load Paper into Tray 1
English (1/2)
5
Connect the Printer to a PC
■ Minimum System Requirements
• IBM-compatible PC with a Pentium/Celeron series,
AMD K6/Athron/Duron family or compatible 200
MHz processor (300 MHz recommended)
• Windows XP/Me/2000/98/95/NT 4.0
• 16 MB RAM (Windows 98/95/NT 4.0), 32 MB RAM
(Windows Me), 64 MB RAM (Windows 2000), or
128 MB RAM (Windows XP)
• 36 MB free hard disk space (20 MB for printer
driver and status display, 16 MB for image
processing)
• IEEE 1284 Type B parallel port or USB Revision
1.1 port
• CD-ROM drive
■ Parallel Interface (Windows XP/2000/Me/
98/95/NT 4.0)
CAUTION
Using the wrong type of cable can damage the
socket on the printer. Use only an IEEE 1284 type B
shielded interface cable.
2
Choose a Location
1
Turn off both the
printer and the
PC.
2
Connect one end
of the interface
cable to the parallel port of the PC.
3
Connect the other
end of the interface cable to the parallel interface connector on
the back of the printer. Secure the cable using the
two clips.
4
Turn on the printer and then, when it’s ready, turn
on the PC.
5
If you’re using Windows XP/Me/2000/98, plug-andplay printer driver installation should start
automatically. Follow the instructions on the
screen.
■ Space Requirements
Provide enough space around the printer to ensure
easy printer operation, paper and toner replacement,
and maintenance.
5.9 in.
11.8 in.
(300 mm)
(150 mm)
23.2 in. (589 mm)
3.9 in. (100 mm)
■ Connect the Power Cord
Use only the power cord supplied with the printer.
3.9 in. (100 mm)
35.1 in. (891 mm)
1
11.2 in.
(285 mm)
21.7 in.
(550 mm)
15.6 in.
(395 mm)
16.1 in. (410 mm)
18.7 in. (475 mm)
■ Precautions
Set up the printer in a place that is
•
•
•
•
•
•
•
•
•
•
•
If you’re using Windows 95/NT 4.0, or if plug-andplay doesn’t start automatically, use the instructions in Section 6, “Install the Printer Driver,” to
install the printer driver manually.
CAUTION
dry and free from dust
on a stable surface
well ventilated
near an easily accessible power socket
away from objects which might obstruct the
printer’s ventilation grille
away from highly flammable items (such as curtains)
away from splashing liquids
away from organic gases (such as ammonia)
away from direct sunlight
away from severe temperature fluctuations
away from exhaust-air from heating, ventilation,
and air-conditioning systems
2
Make sure that the
printer’s power
switch is in the “O”
(OFF) position.
Plug one end of the
power cord that
comes with the
printer into the power cord socket on the back of
the printer. Plug the other end into a power outlet.
■ Turn on the Printer
Set the power switch to
the “I” (ON) position. The
printer is ready to use in
approximately 20
seconds. The green
“Ready” indicator should
be on (but not blinking)
and the orange “Error”
indicator off.
■ USB Interface (Windows XP/2000/Me/98)
CAUTION
Using the wrong type of cable can damage the
socket on the printer. Use only a USB Revision 1.1
compliant cable.
1
Turn off both the
PC and the
printer.
2
Turn on the PC.
3
Turn on the
printer.
4
When Windows
and the printer are
both ready, connect one end of the interface cable
to the PC’s USB port.
5
Connect the other end of the interface cable to the
USB interface connector on the back of the printer.
6
Plug-and-play printer driver installation should
start automatically. Follow the instructions on the
screen.
If plug-and-play doesn’t start automatically, use
the instructions in Section 6, “Install the Printer
Driver,” to install the printer driver manually.
EDNord - Istedgade 37A - 9000 Aalborg - telefon 96333500
PagePro 1250W Setup Guide
6
■ Laser Safety Label
Install the Printer Driver
1
Insert the CD-ROM in your CD-ROM drive.
The setup program automatically starts.
2
Follow the instructions on the screen to install the
printer driver and printer management utilities.
3
Register your printer in one of the following ways:
CAUTION
• On the Main Menu screen, choose Register
(Internet connection required).
• Go to www.onlineregister.com/minolta-qms
(Internet connection required).
• Fill out and mail in the registration card that
came with the printer.
Use of controls, adjustments or
performance of procedures other than
those specified in this manual may result
in hazardous radiation exposure.
This is a semiconductor laser. The maximum power of
the laser diode is 5 mW and the wavelength is 770–
795 nm. A laser safety label is attached to the back of
the printer.
4
On the Main Menu screen, choose Exit to close
the setup program.
5
Remove the CD-ROM, and store it in a safe place.
7
English (2/2)
110-127 V area:
THIS PRODUCT WITH 21 CFR
CHAPTER I, SUBCHAPER J.
Safety Information
220-240 V area:
CLASS 1 LASER PRODUCT
■ Laser Safety
This is a page printer which operates by means of a
laser. There is no possibility of danger from the laser,
provided the printer is operated according to the
instructions in this manual.
■ Laser Caution Label
A laser caution label is attached inside the printer.
Since radiation emitted by the laser is completely confined within protective housing, the laser beam cannot
escape from the machine during any phase of user
operation.
■ Internal Laser Radiation
Maximum average radiation power: 35 µW at the laser
aperture of the print head unit.
Wavelength: 770–795 nm.
This product employs a Class 3b laser diode that
emits an invisible laser beam. The laser diode and the
scanning polygon mirror are incorporated in the print
head unit.
The print head unit is NOT A FIELD SERVICEABLE
ITEM. Therefore, the print head unit should not be
opened under any circumstances.
Laser aperture of the
print head unit
■ Ozone Release
During printer operation, a small quantity of ozone is
released. This amount is not large enough to harm
anyone adversely. However, be sure the room where
the printer is being used has adequate ventilation,
especially if you are printing a high volume of
materials or if the printer is being used continuously
over a long period.
■ For European Users—CE Marking
(Declaration of Conformity)
This product complies with the following EU directives:
89/336/EEC, 73/23/EEC, and 93/68/EEC. This declaration is valid for the area of the European Union (EU)
only.
■ For United States Users—
CDRH Regulation
This machine is certified as a Class 1 Laser product
under the Radiation Performance Standard according
to the Food, Drug and Cosmetic Act of 1990. Compliance is mandatory for Laser products marketed in the
United States and is reported to the Center for
Devices and Radiological Health (CDRH) of the US
Food and Drug Administration of the US Department
of Health and Human Services (DHHS). This means
that this device does not produce hazardous laser
radiation.
This device must be used with a shielded parallel
interface cable or shielded USB interface cable. The
use of non-shielded cables is likely to result in interference with radio communications and is prohibited
under 89/336/EEC rules.
The label shown below indicates compliance with the
CDRH regulations and must be attached to laser products marketed in the United States.
The following are trademarks or registered trademarks
of MINOLTA-QMS: QMS and the MINOLTA-QMS logo.
The following are trademarks or registered trademarks
of Minolta Co., Ltd.: Minolta and PagePro. All other
trademarks are the property of their respective owners.
Copyright © 2002, MINOLTA-QMS, Inc., One Magnum
Pass, Mobile, AL, 36618 USA. All Rights Reserved.
1800671-001A
EDNord - Istedgade 37A - 9000 Aalborg - telefon 96333500
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement