Philips MCM2320 User manual
Philips MCM2320 allows you to enjoy your favorite music from CDs, USB drives, and connected external devices, or listen to FM radio. Enhance your listening experience with the Digital Sound Control feature. Easily program your favorite radio stations and tracks, and use the remote control for convenient operation. Set sleep and alarm timers to wake up to your favorite tunes or fall asleep to soothing music.
PDF
Download
Document
Advertisement
Advertisement
Always there to help you Register your product and get support at www.philips.com/welcome Question? Contact Philips User manual Contents 7 Other features 1 Important 2 Safety Notice 2 2 2 Your Micro Music System Introduction What's in the box Overview of the main unit Overview of the remote control 3 Get started Connect speakers Connect power Prepare the remote control Demonstrate the features Power on Set the clock Select a source 4 Play Play from disc Play from USB Control play Skip tracks Program tracks 5 Listen to the radio Tune to a radio station Program radio stations automatically Program radio stations manually Select a preset radio station 6 Adjust sound Select a preset sound effect Adjust volume level Mute sound 4 4 4 5 6 12 Set the alarm timer Set the sleep timer Listen to an external device 12 13 13 8 Product information 14 9 Troubleshooting 15 6SHFLÀFDWLRQV USB playability information Supported MP3 disc formats 15 15 7 7 7 8 8 8 8 9 9 9 10 10 10 10 11 11 11 11 11 12 12 12 12 EN 1 1 Important Safety Read and understand all instructions before you use this micro music system. If damage is caused by failure to follow the instructions, the warranty does not apply. 5LVNRIHOHFWULFVKRFNRUÀUH Never remove the casing of the product. Never expose the product and accessories to rain or water. Never place liquid containers, such as vases, near the product. If liquids are spilt on or into the product, disconnect it from the power outlet immediately. Contact the Consumer Care to have the product checked before use. Never place the product and accessories QHDUQDNHGÁDPHVRURWKHUKHDWVRXUFHV including direct sunlight. Never insert objects into the ventilation slots or other openings on the product. Where the mains plug or an appliance coupler is used as the disconnect device, the disconnect device shall remain readily operable. Disconnect the product from the power outlet before lightning storms. When you disconnect the power cord, hold the plug securely, never the cable. Batteries (battery pack or batteries installed) shall not be exposed to excessive KHDWVXFKDVVXQVKLQHÀUHRUWKHOLNH 5LVNRIVKRUWFLUFXLWRUÀUH Before you connect the product to the power outlet, make sure that the power voltage matches the value printed on the back of the product. Never connect the product to the power outlet if the voltage is different. 2 EN Never expose the remote control or batteries to rain, water, sunshine, or excessive heat. Avoid force coming onto power plugs. /RRVHSRZHUSOXJVFDQFDXVHDUFLQJRUÀUH Correctly install the battery with its polarity (+/- signs) as marked on the remote control. Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type. 5LVNRILQMXU\RUGDPDJHWRWKHSURGXFW Visible and invisible laser radiation when open. Avoid exposure to beam. Do not touch the disc optical lens inside the disc compartment. Never place the product or any objects on power cords or on other electrical equipment. If the product is transported in temperatures below 5°C, unpack the product and wait until its temperature matches room temperature before connecting it to the power outlet. 5LVNRIRYHUKHDWLQJ 1HYHULQVWDOOWKLVSURGXFWLQDFRQÀQHG space. Always leave a space of at least four inches around the product for ventilation. Make sure that curtains or other objects never cover the ventilation slots on the product. 5LVNRIFRQWDPLQDWLRQ Remove the battery if it is exhausted or if the remote control is not to be used for an extended period of time. Batteries contain chemical substances, they should be disposed of properly. Notice $Q\FKDQJHVRUPRGLÀFDWLRQVPDGHWRWKLV device that are not expressly approved by WOOX Innovations may void the user’s authority to operate the equipment. Compliance This product complies with the radio interference requirements of the European Community. This apparatus includes this label: Care of the environment Your product is designed and manufactured with high quality materials and components, which can be recycled and reused. When this crossed-out wheeled bin symbol is attached to a product it means that the product is covered by the European Directive 2002/96/ EC. Please inform yourself about the local separate collection system for electrical and electronic products. Please act according to your local rules and do not dispose of your old products with your normal household waste. Correct disposal of your old product helps to prevent potential negative consequences for the environment and human health. Your product contains batteries covered by the European Directive 2006/66/EC, which cannot be disposed with normal household waste.Please inform yourself about the local rules on separate collection of batteries because correct disposal helps to prevent negative consequences for the environmental and human health. Environmental information All unnecessary packaging has been omitted. We have tried to make the packaging easy to separate into three materials: cardboard (box), polystyrene foam (buffer) and polyethylene (bags, protective foam sheet.) Your system consists of materials which can be recycled and reused if disassembled by a specialized company. Please observe the local regulations regarding the disposal of packaging materials, exhausted batteries and old equipment. The making of unauthorized copies of copyprotected material, including computer SURJUDPVÀOHVEURDGFDVWVDQGVRXQG recordings, may be an infringement of copyrights and constitute a criminal offence. This equipment should not be used for such purposes. Care for your product Do not insert any objects other than discs into the disc compartment. Do not insert warped or cracked discs into the disc compartment. Remove the discs from the disc compartment if you are not using the product for an extended period of time. 2QO\XVHPLFURÀEHUFORWKWRFOHDQWKH product. Note The type plate is located on the back of the product. EN 3 2 Your Micro Music System Congratulations on your purchase, and ZHOFRPHWR3KLOLSV7RIXOO\EHQHÀWIURPWKH support that Philips offers, register your product at www.philips.com/welcome. Introduction With this unit, you can: enjoy audio from discs, USB devices, and other external devices; listen to radio stations. You can enrich sound output with below sound effect: Digital Sound Control (DSC) The unit supports these media formats: What's in the box Check and identify the contents of your package: Main unit Remote control (with one AAA battery) Speaker boxes (×2) Short user manual Safety and notice 4 EN Overview of the main unit h a b g c f d e a Turn on the product. Switch to standby mode or ECO power standby mode. Start or pause play. Stop play. Erase a program. b Display panel Show current status. c Connect USB storage devices. d AUDIO IN Connect external audio devices. e Disc compartment f Open or close the disc compartment. g VOLUME Adjust volume. h SOURCE Select a source: DISC, USB, TUNER, AUDIO IN. / Skip to previous/next track. Search within a track/disc. Tune to a radio station. Adjust time. EN 5 f VOL +/ Adjust volume. Overview of the remote control g MUTE Mute or restore volume. a b c CD FM r h SOUND Enrich sound effect with Digital Sound Control (DSC). q i CLOCK Set the clock. View clock information. AUDIO IN PRESET/ALBUM d p e REPEAT f VOL g SHUFFLE MUTE DISPLAY SOUND CLOCK PROG TIMER h i SLEEP o n m l k j j SLEEP/TIMER Set sleep timer. Set alarm timer. k PROG Program tracks. Program radio stations. Auto store FM radio stations. l DISPLAY Adjust display brightness. m SHUFFLE Play tracks randomly. n Stop play or erase a program. a Turn the unit on or off. Switch to standby mode or ECO power standby mode. b CD Select CD source. c FM Select FM source. d PRESET/ALBUM / Select a preset radio station. Skip to previous/next album. e 6 EN / Skip to the previous/next track. Search within a track/disc/USB. Tune to a radio station. Adjust time. o REPEAT Play a track or all tracks repeatedly. p Start, pause, or resume play. q USB/AUDIO IN Select USB or AUDIO IN source. r Open or close the disc compartment. 3 Get started Caution Use of controls or adjustments or performance of procedures other than herein may result in hazardous radiation exposure or other unsafe operation. Always follow the instructions in this chapter in sequence. Connect speakers Note Insert the stripped portion of each speaker wire into Connect power the socket completely. For better sound quality, use the supplied speakers only. Connect only speakers with impedance that is the same or higher than the supplied speakers (refer to the 6SHFLÀFDWLRQVVHFWLRQRIWKLVPDQXDO Caution Risk of product damage! Ensure that the power supply 1 2 3 4 )RUWKHULJKWVSHDNHUÀQGWKHVRFNHWVRQ the back of the main unit marked "R". voltage corresponds to the voltage printed on the back or the underside of the unit. Before you connect the AC power cord, ensure that you have completed all other connections. Insert the red wire into the red (+) socket, and the black wire into the black (-) socket. )RUWKHOHIWVSHDNHUÀQGWKHVRFNHWVRQWKH main unit marked "L". Repeat step 2 to insert the left speaker wire. To insert each speaker wire: 1 2 3 +ROGGRZQWKHVRFNHWÁDS Insert the speaker wire fully. 5HOHDVHWKHVRFNHWÁDS Connect the power cable to the wall socket. EN 7 Prepare the remote control Caution Note MCM2320 switches to Standby mode after 15 minutes inactive. Risk of product damage! When the remote control is not used for long periods, remove the batteries. To insert the remote control battery: 1 2 3 Open the battery compartment. Insert the supplied AAA battery with correct polarity (+/-) as indicated. Close the battery compartment. Switch to ECO power standby mode Press and hold for more than two seconds. » The red ECO power standby indicator turns on. In Eco power standby mode, press to switch between working mode and ECO power standby mode. Note MCM2320 switches to ECO power Standby mode after 15 minutes in standby mode. Demonstrate the features In standby mode, press to demonstrate features of this device. » The features are displayed one by one across the display panel. To turn off the demonstration, press again. Switch between standby mode and ECO power standby mode: Press and hold for more than two seconds. Set the clock 1 Power on Press . » MCM2320 switches to the last selected source. 2 3 Switch to standby mode Press again to switch MCM2320 to standby mode. » The clock (if set) is displayed on the panel. In standby mode, press to switch between working mode and standby mode. 8 EN 4 In standby mode, press and hold CLOCK for more than two seconds to enter the clock setting mode. » [24H] or [12H] is displayed. Press / to select 24H or 12H hour format, and then press CLOCK. » The hour digits begin to blink. Press / to set the hour, and then press CLOCK. » The minute digits begin to blink. Press / to set the minute, and then press CLOCK. » The set clock is displayed. Note 4 Play To view clock information in working mode, press CLOCK. If no button is pressed in 90 seconds during setting, MCM2320 exits clock setting without saving earlier operations. Select a source On the main unit Press SOURCE repeatedly to select a source. [DISC]: the disc in the disc compartment [USB]PSÀOHVVWRUHGRQWKHFRQQHFWHG USB storage device [TUNER]: the FM tuner [AUDIO IN]: the audio input through the AUDIO IN socket Play from disc 1 2 3 4 Press CD to select CD source. Press to open the disc compartment. Insert a disc with the label side up. Press to close the disc compartment. » Play starts automatically. If not, press . On the remote control Press CD, FM, or AUDIO IN/USB to select each source directly. CD: the disc in the disc compartment FM: the FM tuner AUDIO IN/USB: the audio input through the AUDIO INVRFNHWRUWKHPSÀOHV stored on the connected USB storage device CD EN 9 Play from USB Note Make sure that the USB device contains playable audio VOL +/MUTE SOUND DISPLAY Increase or decrease the volume. Mute or restore sound. Select a preset sound equalizer. Adjust display brightness. content. 1 2 Insert a USB device into the socket. Press USB/AUDIO IN repeatedly to select the USB source. » Play starts automatically. If not, press . Skip tracks When playing a CD: Press / to select tracks. When playing an MP3 disc and USB: 1 2 Press Press / to select an album or a folder. / WRVHOHFWDWUDFNRUDÀOH Program tracks This function allows you to program 20 tracks in the desired sequence. 1 USB 2 3 Control play / / REPEAT SHUFFLE 10 EN Start, pause, or resume play. Stop play. Select an album or a folder. Press to skip to the previous or next track. Press and hold to search backward/forward within a track. Play a track or all tracks repeatedly. Play tracks randomly. 4 5 In stop mode, press PROG to activate the program mode. » [PROG] (program) and [01 PR 01] are displayed. For MP3 tracks, press album. / to select an Press / to select a track, and then press PROGWRFRQÀUP » [PR X] is displayed, where 'X' is the next position in the program. Repeat steps 2 to 3 to program more tracks. Press to play the programmed tracks. » During play, [PROG] (program) is displayed. To erase the program Press twice. 5 Listen to the radio Tune to a radio station Tip Program radio stations manually 1 2 3 Position the antenna as far as possible from TV, VCR, or other radiation source. For optimal reception, fully extend and adjust the position of the antenna. 1 2 Press FM repeatedly to select FM source. Press and hold / for more than two seconds. » The radio tunes to a station with strong reception automatically. 3 Repeat step 2 to tune to more stations. To tune to a weak station: Press / UHSHDWHGO\XQWLO\RXÀQGRSWLPDO reception. 4 Tune to a radio station. Press PROG, and then press select a number from 1–20. / to Press PROGWRFRQÀUP » The preset number and the frequency of the preset station are displayed. Repeat steps 1-3 to program more stations. Note To overwrite a programmed station, store another station in its place. Select a preset radio station In tuner mode, press number. / to select a preset Program radio stations automatically Note You can program a maximum of 20 preset radio stations (FM). In tuner mode, press and hold PROG for more than two seconds to activate automatic programming. » All available stations are programmed in the order of waveband reception strength. » 7KHÀUVWSURJUDPPHGUDGLRVWDWLRQLV broadcast automatically. EN 11 6 Adjust sound The following operations are applicable to all supported media. Select a preset sound effect Press SOUND repeatedly to select a preset sound effect. DSC1, DSC2, DSC3, DSC4, and DSC5 Adjust volume level On the remote control, press VOL +/repeatedly. On the main unit, rotate the volume knob. 7 Other features Set the alarm timer This product can be used as an alarm clock. You FDQVHOHFWWKHGLVF)0RUPSÀOHVRQD86% storage device as alarm source. Note Make sure that you have set the clock correctly. If the selected alarm source is unavailable, this product switches to FM mode automatically. 1 In normal standby mode, press and hold SLEEP/TIMER for two seconds. » The hour digits blink. » Mute sound 2 Press MUTE to mute or restore the sound. 3 4 5 is displayed. Press / repeatedly to set the hour, and then press SLEEP/TIMERWRFRQÀUP » The minute digits blink. Press / to set the minute, and then press SLEEP/TIMERWRFRQÀUP » The last selected alarm source blinks. Press / to select an alarm source (DISC, USB or Tuner), and then press SLEEP/TIMERWRFRQÀUP » VOL_XX (XX indicates the volume level of alarm) blinks. Press / to set the alarm volume, and then press SLEEP/TIMERWRFRQÀUP Stop an alarm When an alarm ring, press another mode. 12 EN or switch to Note If you do not stop an alarm, it keeps ringing for 30 minutes, and then the product automatically switches to normal standby mode. Listen to an external device You can listen to an external device through this unit with an MP3 link cable. 1 Activate/deactivate alarm timer In standby mode, press SLEEP/TIMER repeatedly to activate or deactivate timer. » If timer is activated, is displayed. Tip 2 3 Connect an MP3 link cable (not supplied) between: AUDIO IN jack (3.5 mm) on the unit, and the headphone jack on an external device. Press AUDIO IN repeatedly to select AUDIO IN source. Start to play the device (see the device user manual). Alarm timer is not available in AUDIO IN mode. Set the sleep timer MCM2320 switches to the standby mode automatically after the set time. When MCM2320 is turned on, press SLEEP/TIMER repeatedly to select a time period (in minutes). » When the sleep timer is activated, is displayed. AUDIO IN To show the remaining time Press SLEEP/TIMER. To deactivate the sleep timer Press SLEEP/TIMER repeatedly until [OFF] is displayed. EN 13 8 Product information Note notice. $PSOLÀHU 30 W 60 Hz - 16 kHZ; +3 dB >70 dB <1% 800 mV RMS Speakers Speaker Impedance Speaker Driver Sensitivity 4 ohm Fullrange 4" >83 dB/m/W Tuner (FM) Tuning Range Tuning grid Sensitivity - Mono, 26dB S/N Ratio - Stereo, 46dB S/N Ratio Search Selectivity Total Harmonic Distortion Signal to Noise Ratio 14 EN 2.0 full speed P$ Laser Type Disc Diameter Support Disc Semiconductor 12 cm/8 cm CD-DA, CD-R, CDRW, MP3-CD 24 Bits/44.1 kHz <1% (1 kHz) Audio DAC Total Harmonic Distortion Frequency Response 6SHFLÀFDWLRQV Signal to Noise Ratio Total Harmonic Distortion Aux Input USB Direct Version USB 5 V Power Disc Product information is subject to change without prior Maximum Output Power Frequency Response USB 87.5-108 MHz 50 KHz <22 dBu <45 dBu <30 dBu <3% >45 dB 60 Hz - 16 kHZ; ±3 dB >70 dBA S/N Ratio General information AC power Operation Power Consumption Eco Standby Power Consumption Dimensions - Main Unit (W x H x D) - Speaker Box (W x H x D) Weight - Main Unit - Speaker Box 100-240 V~, 50/60 Hz 15 W <0.5 W 180 x 121 x 247 mm 156 x 253.5 x 128 mm 1.6 kg 1.16 kg x 2 USB playability information Compatible USB devices: 86%ÁDVKPHPRU\86%RU86% 86%ÁDVKSOD\HUV86%RU86% memory cards (requires an additional card reader to work with this unit) Supported USB formats: 86%RUPHPRU\ÀOHIRUPDW)$7)$7 FAT32 (sector size: 512 bytes) MP3 bit rate (data rate): 32-320 Kbps and variable bit rate Directory nesting up to a maximum of 8 levels Number of albums/ folders: maximum 99 Number of tracks/titles: maximum 999 File name in Unicode UTF8 (maximum length: 32 bytes) Unsupported USB formats: Empty albums: an empty album is an album WKDWGRHVQRWFRQWDLQ03:0$ÀOHVDQG will not be shown in the display. 8QVXSSRUWHGÀOHIRUPDWVDUHVNLSSHG)RU example, word documents (.doc) or MP3 ÀOHVZLWKH[WHQVLRQGOIDUHLJQRUHGDQG not played. :0$$$&:$93&0DXGLRÀOHV '50SURWHFWHG:0$ÀOHVZDYPD .m4p, .mp4, .aac) :0$ÀOHVLQ/RVVOHVVIRUPDW Supported MP3 disc formats ISO9660, Joliet Maximum title number: 128 (depending on ÀOHQDPHOHQJWK Maximum album number: 99 Supported sampling frequencies: 32 kHz, 44.1 kHz, 48 kHz Supported Bit-rates: 32~256 (kbps), variable bit rates 9 Troubleshooting Warning Never remove the casing of this device. To keep the warranty valid, never try to repair the system yourself. If you encounter problems when using this device, check the following points before requesting service. If the problem remains unsolved, go to the Philips Web page (www. philips.com/support). When you contact Philips, make sure that the device is nearby and the model number and serial number are available. No power Make sure that the AC power cord of the device is connected properly. Make sure that there is power at the AC outlet. As a power-saving feature, the system switches off automatically 15 minutes after track play reaches the end and no control is operated. No sound or poor sound Adjust the volume. Check that the speakers are connected correctly. Check if the stripped speaker wires are clamped. No response from the unit Disconnect and reconnect the AC power plug, then turn on the unit again. As a power-saving feature, the system switches off automatically 15 minutes after track play reaches the end and no control is operated. EN 15 Remote control does not work %HIRUH\RXSUHVVDQ\IXQFWLRQEXWWRQÀUVW select the correct source with the remote control instead of the main unit. Reduce the distance between the remote control and the unit. Insert the battery with its polarities (+/– signs) aligned as indicated. Replace the battery. Aim the remote control directly at the sensor on the front of the unit. No disc detected Insert a disc. Check if the disc is inserted upside down. Wait until the moisture condensation at the lens has cleared. Replace or clean the disc. 8VHDÀQDOL]HG&'RUFRUUHFWIRUPDWGLVF &DQQRWGLVSOD\VRPHÀOHVLQ86%GHYLFH 7KHQXPEHURIIROGHUVRUÀOHVLQWKH86% device has exceeded a certain limit. This phenomenon is not a malfunction. 7KHIRUPDWVRIWKHVHÀOHVDUHQRW supported. USB device not supported The USB device is incompatible with the unit. Try another one. Poor radio reception Increase the distance between the unit and your TV or VCR. Fully extend the FM antenna. Timer does not work Set the clock correctly. Switch on the timer. Clock/timer setting erased Power has been interrupted or the power cord has been disconnected. Reset the clock/timer. 16 EN EN 17 Specifications are subject to change without notice. 2014 © WOOX Innovations Limited. All rights reserved. Philips and the Philips’ Shield Emblem are registered trademarks of Koninklijke Philips N.V. and are used by WOOX Innovations Limited under license from Koninklijke Philips N.V. MCM2320_12_UM_V1.0 ">
Advertisement