LG | GB3133WBGW | manual | LG GB3133WBGW fridge-freezer

ENGLISH
Please read this manual carefully before operating
your set and retain it for future reference.
P/NO.: MFL63730280
www.lg.com
LG Customer Information Center
☎ LG SERVICE : (UNITED KINGDOM) 0844-847-5454
Register your product Online!
www.lg.com
(In the UK Only)
Important
The wires in this mains lead are coloured in accordance
with the following code:
GREEN AND YELLOW:EARTH
BLUE:NEUTRAL
BROWN:LIVE
This appliance must be earthed
As the colours of the wires in the mains lead of this
apparatus may not correspond with the coloured
markings identifying the terminals in your plug, proceed
as follows:
The wire which is coloured Green and Yellow must be
connected to the terminal in the plug which is marked
with the letter E or by the earth symbol( ) or coloured
Green or Green and Yellow.
The wire which is coloured Blue must be connected to
the terminal which is marked with the letter N or
coloured Black.
The wire which is coloured Brown must be connected to
the terminal which is marked with the letter L or
coloured Red.
If a 13 amp(BS 1363) plug is used, fit a 13 amp BS 1362
fuse.
2
Table of Contents
Introduction
Installation
Operation
Registration
4
Important Safety Instruction
4
Identification of Parts
16
Installation
17
Starting
17
Temperature Control
18
Refrigerator
18
Freezer
18
Function
Suggestion On
Food storage
Care and
Maintenance
Trouble Shooting
To Reverse the Doors
3
20
Super Freezer
20
Vacation
20
Lock
21
Memory Feature
21
Door Alarm
21
Self Test
21
Ice Making
21
Defrosting
21
Water Dispenser
22
Storing Food
24
General Information
Lamp Replacement
25
25
Cleaning
26
Trouble Shooting
28
Precaution
30
How to Reverse the Door
30
Introduction
Registration
Introduction
The model and serial number are found on the rear of
this unit. This number is unique to this unit and not
available to others. You should record requested
information here and retain this guide as a permanent
record of your purchase. Staple your receipt here.
Date of Purchase
:
Dealer Purchased From
Dealer Address
:
Dealer Phone No.
:
Model No.
:
Serial No.
:
:
Important Safety Instruction
BASIC SAFETY PRECAUTIONS
This guide contains many important safety messages.
Always read and obey all safety messages.
This is the safety alert symbol. It alerts you to safety
messages that inform you of hazards that can kill or hurt
you or others or cause damage to the product. All safety
messages will be preceded by the safety alert symbol and
the hazard signal word DANGER, WARNING, or
CAUTION. These words mean:
DANGER
You will be killed or seriously injured if
you don’t follow instructions.
WARNING You can be killed or seriously injured if
you don’t follow instructions.
CAUTION
Indicates an imminently hazardous
situation which, if not avoided, may
result in minor or moderate injury, or
product damage only.
All safety messages will identify the hazard, tell you how
to reduce the chance of injury, and tell you what can
happen if the instructions are not followed.
4
Introduction
Important Safety Instruction
WARNING
To reduce the risk of fire, electric shock, or injury to
persons when using your product, basic safety
precautions should be followed, including the
following. Read all instructions before using this
appliance.
1. When connecting the power
The dedicated outlet should be used.
• Using several devices at one outlet
may cause fire.
• The electric leakage breaker may
damage food and the dispenser may
be leaked.
Do not allow the power plug to face upward or to
be squeezed at the back of the fridge-freezer.
Water may be flown into or the plug
may be damaged, which causes fire or
electric shock.
Do not allow the power cord bent or pressed by the
heavy object to be damaged.
It may damage the power cord to cause
fire or electric shock.
Do not extend or modify the length of the power
plug.
It causes electric shock or fire by the
electric damage of the power cord or
others.
Unplug the power plug when cleaning, handling or
replacing the interior lamp of the fridge-freezer.
• It may cause electric shock or injury.
• When replacing the interior lamp of
the fridge-freezer, make sure that the
rubber ring for preventing the electric
spark within the socket is not taken off.
5
Introduction
Important Safety Instruction
Do not pull out the cord or touch the power plug
with wet hands.
• It may cause electric shock or injury.
Remove water or dust from the power plug and
insert it with the ends of the pins securely
connected.
Dust, water or unstable connection may
fire or electric shock.
Make sure of grounding.
The incorrect grounding may cause
breakdown and electric shock.
When the power cord or the power plug is
damaged or the holes of the outlet are loosed, do
not use them.
It may cause electric shock or short circuit
to make fire.
2. When using the fridge-freezer
Do not place the heavy object or the dangerous
object (container with liquid) on the fridge-freezer.
It may be dropped to cause injury, fire or
electric shock when opening or closing
the door.
Do not cling to the door or the shelves of the door
or the home bar of the freezer or the cool chamber.
It may make the fridge-freezer fallen
down or damage the hands. Especially,
do not allow the children to do the
above.
6
Introduction
Important Safety Instruction
Water tank can fill with potable
water only.
Do not install the fridge-freezer in the wet place or
the place which water or rain splashes.
Deterioration of insulation of electric
parts may cause electric leakage.
Do not use or store inflammable materials ether,
benzene, alcohol, medicine, LP gas, spray or
cosmetics near or in the fridge-freezer.
It may cause explosion or fire.
Do not place the lit candle within the fridge-freezer
to deodorize.
It may cause explosion or fire.
Do not store the medicine or the academic materials
at the fridge-freezer.
When the material with the strict
temperature control is stored, it may be
deteriorated or it may make an
unexpected reaction to cause any risk.
Do not use the combustible spray near the fridgefreezer.
It may cause fire.
7
Introduction
Important Safety Instruction
Avoid the heating devices.
It may cause fire.
Do not place flower vase, cup, cosmetics, medicine
or any container with water on the fridge-freezer.
It may cause fire, electric shock or
injury by dropping down.
Use the submerged fridge-freezer after checking it.
It may cause electric shock or fire.
When gas is leaked, do not touch the fridge-freezer
or the outlet and ventilate the room immediately.
• The explosion by spark may cause
fire or burn.
• Because this fridge-freezer uses
natural gas (isobutene, R600a) as
the environment-friendly
refrigerant, even a small amount
(80~90g) is combustible. When the gas is leaked by the
severe damage during delivering, installing or using the
fridge-freezer, any spark may cause fire or burn.
Do not spray water at the outside or the inside of
the fridge-freezer or do not clean it with benzene or
thinner.
Deterioration of insulation of electric
parts may cause electric shock or fire.
8
Introduction
Important Safety Instruction
When any strange smell or smoke is detected from
the fridge-freezer, disconnect the power plug
immediately and contact to the service center.
It may cause fire.
Do not allow any person except the qualified
engineer to disassemble, repair or alter the fridgefreezer.
It may cause injury, electric shock or
fire.
Do not use the fridge-freezer for non-domestic
purpose (storing medicine or testing material, using
at the ship, etc.).
It may cause an unexpected risk such
as fire, electric shock, deterioration of
stored material or chemical reaction.
When disposing the fridge-freezer, remove the
packing materials from the door.
It may cause to lock out the child.
Install the fridge-freezer on the solid and level floor.
Installing it on the unstable place may
cause death by falling down the
fridge-freezer when opening or
closing the door.
9
Introduction
Important Safety Instruction
Do not insert the hands or the metal stick into the
exit of cool air, the cover, the bottom of the fridgefreezer, the heatproof grill (exhaust hole) at the
backside.
It may cause electric shock or injury.
When you want to dispose the fridge-freezer,
contact to the down-block office.
When you want to dispose the large
living waste such as
electric home appliance and furniture,
you’d better contact the local downblock office.
Violating this direction may cause injury or damage
house or furniture. Always be careful, please.
Do not touch food or containers at
the freezer with wet hands.
It may cause frostbite.
Wait for 5 minutes or longer when
reconnecting the plug.
It may cause the operation of the
freezer to fail.
Do not put bottle in the freezer.
It may freeze the contents to break the
bottle to cause injury.
Pull out the power plug not by
grasping the cord but the plug of its
end.
It may cause electric shock or short
circuit to fire.
10
Introduction
Important Safety Instruction
Do not install the fridge-freezer in the wet place or
the place which water or rain splashes.
Deterioration of insulation of electric
parts may cause electric leakage.
Do not insert the hands into the bottom of the
fridge-freezer.
The iron plate of the bottom may
cause injury.
Carry the fridge-freezer with the handle bar at the
bottom of the front and the top of the rear.
Otherwise, your hands may be slipped
to cause injury.
Because opening or closing the door of the fridgefreezer may cause injury to the person around it, be
careful, please.
Opening or closing the door may
cause feet or hands to be caught in
the chink in door or the child to be get
hurt by the corner.
Do not put any living animal in the
fridge-freezer.
This appliance is not intended for use by persons (including
children) with reduced physical, sensory or mental capabilities,
or lack of experience and knowledge, unless they have been
given supervision or instruction concerning use of the appliance
by a person responsible for their safety.
Children should be supervised to ensure that they do not play
with the appliance.
CAUTION
11
Introduction
Important Safety Instruction
WARNING
Precaution
• This fridge-freezer must be properly installed and
located in accordance with the Installation
Instruction before it is used.
• Never unplug your fridge-freezer by pulling on the
power cord. Always grip plug firmly and pull straight
out from the outlet.
• When moving your appliance away from the wall, be
careful not to roll over or damage the power cord.
• After your fridge-freezer is in operation, do not
touch the cold surfaces in the freezer compartment,
particularly when hands are damp or wet.
Skin may adhere to these extremely cold surfaces.
• Pull out the power plug prior to cleaning the fridgefreezer.
Never damage, serverely bend, pull out, or twist the
power cord because power cord damage may cause a
fire or electronic shock.
Never place glass products in the freezer because they
may be broken when their inner contents are frozen.
• Do not directly spray water inside or outside the
fridge/freezer.
There is a risk of explosion or fire.
• Do not insert the power plug with wet hands.
You may receive an electric shock.
• Do not put a container filled with water on top of
the appliance.
If the water spills on to any electrical parts, it may lead
to fire or electric shock.
• Do not install the fridge/freezer in a damp place,
where it could be splashed with water.
Incorrect insulation of the electrical parts may cause an
electric shock or file.
12
Introduction
Important Safety Instruction
• Do not disassemble, repair or alter the appliance.
It may cause fire or abnormal operations, which may
lead to injury.
• Pull the power plug out of the socket before
replacing the interior light in the refrigerator.
Otherwise, there is a risk of electric shock.
• If possible, connect the fridge-freezer to its own
individual electrical outlet to prevent it and other
appliances or household lights from causing an
overload.
Do not modify or
extend the Power
Cord length
It will cause electric shock or fire.
Don’t Use on
Extension Cord
If possible, connect the fridge-freezer to its own individual
electrical outlet to prevent it and other appliances or
household lights from causing an overload.
The supply plug of the refrigerator-freezer should be
placed in easy accessible position for quick disconnection
in emergency.
If the supply cord is damaged, it must be replaced by the
manufacturer or its service agent or a similarly qualified
person in order to avoid a hazard.
Accessibility of
Supply Plug
Supply Cord
Replacement
Risk of child entrapment.
Before you throw away your old refrigerator or freezer:
Take off the doors.
Leave the shelves in place so that children may not easily
climb inside.
Don't store
Don't store or use gasoline or other flammable vapors
and liquids in the vicinity of this or any other appliance.
In the event of an electric short circuit, grounding
(earthing) reduces the risk of electric shock by providing
an escape wire for the electric current. In order to prevent
possible electric shock, this appliance must be grounded.
Improper use of the grounding plug can result in an
electric shock. Consult a qualified electrician or service
person if the grounding instructions are not completely
understood, or if you have doubts on whether the
appliance is properly grounded.
Grounding
(Earthing)
13
Introduction
Important Safety Instruction
Keep ventilation openings, in the appliance enclosure
or in the built-in structure, clear of obstruction.
Do not use mechanical devices or other means to
accelerate the defrosting process, other than those
recommended by the manufacturer.
Do not damage the refrigerant circuit.
Do not use electrical appliances inside the food
storage compartments of the appliance, unless they
are of the type recommended by the manufacturer.
The refrigerant and insulation blowing gas used in the
appliance require special disposal procedures. When
disposal, please consult with service agent or a
similarly qualified person.
This appliance contains a small amount of isobutane
refrigerant (R600a), natural gas with high
environmental compatibility, but it is also
combustible. When transporting and installing the
appliance, care should be taken to ensure that no
parts of the refrigerating circuit are damaged.
Refrigerant squirting out of the pipes could ignite or
cause an eye injury. If a leak is detected, avoid any
naked flames or potential sources of ignition and air
the room in which the appliance is standing for
several minutes.
In order to avoid the creation of a flammable gas air
mixture if a leak in the refrigerating circuit occurs, the size
of the room in which the appliance may be sited depends
on the amount of refrigerant used. The room must be
1m 2 in size for every 8g of R600a refrigerant inside the
appliance. The amount of refrigerant in your particular
appliance is shown on the identification plate inside the
appliance.
Never start up an appliance showing any signs of
damage. If in doubt, consult your dealer.
14
Introduction
Important Safety Instruction
• If the wall socket is loose, do not insert the power
plug.
It may cause electric shock or fire.
• Never unplug your refrigerator by pulling on the
power cord. Always grip plug firmly and pull it
straight out from the outlet.
You may disconnect a wire and cause a short circuit.
• Do not use a wet or damp cloth when cleaning the
plug. Remove any foreign matter from the power
plug pins.
Otherwise, there is a risk of fire.
• Do not put your hands into the bottom area of the
appliance.
Any Sharp edges may cause personal injury..
• After unplugging the appliance, wait for at least
five minutes before plugging it again to the wall
socket.
Abnormal operation of the freezer may cause material
damage.
• If the appliance is not to be used for a long time,
pull out the power plug.
Any deterioration in the insulation may cause fire.
• Do not let children touch or play with the control
panel on the front of the appliance.
• The refrigerant used in fridge/freezer and the
gases in the insulation material require special
disposal procedures. Ensure that none of the pipes
on the back of the appliances are damaged prior
to disposal.
15
Introduction
Identification of Parts
Utility Corner
(movable)
Removable Glass
Shelf
Egg Tray
Lamp
Multi-air Flow Duct
Door Basket
Meat Tray (Optional)
Water Tank
Refrigerator
Temperature Control
Vegetable Drawer
Used to keep fruits and
vegetables, etc. fresh
and crisp.
(1 or 2)
Handle (Optional)
2l Bottle Door
Basket
Ice Cube Tray
Freezer Compartment
Removable Plinth
Leveling Screw
Note
If you find some parts missing from your unit, they
may be parts only used in other models.
16
Installation
1. Select a good location.
Installation
Place your fridge-freezer where it is easy to use.
2. Avoid placing the unit near heat sources,
direct sunlight or moisture.
3. There must be proper air circulation around your
fridge-freezer to keep it operating efficiently.
4. To avoid vibration, the unit must be leveled.
If required, adjust the leveling screws to compensate
for the uneven floor.
The front should be slightly higher than the rear to aid
in door closing.
Leveling screws can be turned easily by tipping the
cabinet slightly.
Turn the leveling screws counterclockwise(
) to
raise the unit, clockwise(
) to lower it.
5. Clean your fridge-freezer thoroughly and wipe off all
dust accumulated during shipping.
6. Install accessories such as ice cube box, etc., in their
proper places.They are packed together to prevent
possible damage during shipment.
7. Connect the power supply cord (or plug) to the outlet.
Don't double up with other appliances on the same
outlet.
8. To ensure proper air circulation around the fridge freezer, please maintain sufficient space on both the
sides as well as top and maintain at least 2 inches (5
cm) from the rear wall.
Starting
When your fridge-freezer is installed, allow it 2-3 hours to
stabilize at normal operating temperature prior to filling
it with fresh or frozen foods.
If power plug is disconnected, allow 5 minutes delay
before restarting.
Your fridge-freezer is now ready for use.
17
Operation
Temperature Control
Your fridge-freezer has two controls that let you regulate
the temperature in the fridge and freezer compartments.
Refrigerator
• Initially set the TEMP. CONTROL at
"4". Then adjust the compartment
temperature according to your
desire.
COLD
7
WARM
1
6
2
5
4
3
• If you want an inside temperature
TEMP. CONTROL
slightly less cold or colder, turn the
knob towards WARM or COLD,
respectively. When the surrounding
temperature is low, adjust the TEMP. CONTROL 'WARM'.
Freezer
Display Panel For Temperature Control
18
Operation
• You can now adjust the temperature of the compartment
as you want.
< LED 88 Type >
< LED BAR Type >
• When you press the temperature control buttons, the
temperature of Freezer compartment is repeated in the
following order.
LED 88 Type Freezer Compartment :
-19°C → -20°C → -21°C → -22°C → -23°C → -15°C
→ -16°C → -17°C → -18°C
LED BAR Type Freezer Compartment :
-19°C → -21°C → -23°C → -15°C → -17°C
Note
The actual inner temperature varies depending on the
food status, as the indicated setting temperature is a
target temperature, not actual temperature within
refrigerator.
Refrigeration function is weak in the initial time.
Please adjust temperature as above after using
refrigerator for minimum 2~3 days.
19
Operation
Function
Super Freezer
• Please select this function for prompt freezer.
• This function is used when you want to freeze the
foods quickly. Press the ‘SUPER FRZ.’ (Super Freezer)
button once, and then the quick freeze operation starts
with the lamp on.
• The Super Freeze operation takes about 3 hours. When
its operation ends, it automatically returns to the
previous temperature setting. If you want to stop the
quick freeze operation, press the ‘SUPER FRZ.’ button
once more, the lamp goes out, and the Super Freeze
operation stops and the refrigerator returns to the
previous temperature setting.
Vacation
• This function makes the fridge-freezer work in a power
saving mode which is useful for when you are away on
holiday, by reducing energy consumption as much as
possible.
Pressing ‘VACATION’ starts operation with lamp on
and pressing it again stops the operation.
20
Operation
Lock
• Pressing this button stops operation of other buttons.
• ”Locking” or “Un-Locking” is repeated whenever
pressing the ‘CHILD LOCK’ button. (For “Locking” or
“Un-Locking” press the ‘CHILD LOCK’ button for 2 secs.)
• When ‘CHILD LOCK’ is activated, pressing the other
buttons would not work.
Memory feature
Function to save the set temperature and vacation status .
When the power is turned on after the power failure, it will be
restored with the set temperature and vacation status.
Door Alarm
• 3 times of warning of 30 seconds if a minute passes with
the door of refrigerator opened or not completely closed.
• Please contact with the local service center if warning
continue to sound even after closing the door.
Self Test
• This function automatically detects failure when failure
is found in product during the use of refrigerator.
• If the failure occurs at product and it does not operate
by pressing any button and normal indication is not
done, do not turn the power off and immediately
contact with the local service center.
• A lot of time is needed for service engineer to detect
the failed part by turning it off.
Ice Making
• To make ice cubes, fill the ice
tray to the water level and place
it in the freezer.
• If ice cubes are required fast,
press the 'SUPER FRZ.' button.
• To remove ice cubes, hold the
tray at its ends and twist gently.
To remove ice cubes easily, run water on the tray
before twisting.
Tip
Defrosting
Defrosting takes place automatically.
The defrosting water flows down to the evaporating tray
and is evaporated automatically.
21
Operation
Water Dispenser
Features
MAX
MIN
Install
WATER LEVEL
WATER LEVEL
• Please assemble the VALVE ASSEMBLY after correctly
adjusting it with a DOOR HOLE.
22
Operation
Filling of
WATER TANK
1. After turning the HANDLE Tank backward with the
WATER TANK installed at the DOOR, Open the CAP
TANK (SMALL) and then fill water using a kettle etc.
* Fill water while watching a sight glass on the front
of the WATER TANK.
* Water up to 3.5 l can be filled.
2. Press and fix the CAP TANK(SMALL).
3. After filling spring water, fix the HANDLE TANK at a
proper position.
Drinking
1. Press the Dispenser Pad with a cup.
2. If pressing the Pad, water inside of the Dispenser is
supplied.
3. If slowly removing a cup from the Pad, water will not
fall down.
Water level
• MAX: Leakage may happen if the water lever is higher
than the lever MAX. The water lever should be kept
under the MAX.
• MIN: There is less pouring water if the water lever is
lower than the lever MIN. The water amount should
be added before using.
CAUTION
Do not use other beverage (milk, juice, carbonated
beverage etc) than spring water. Especially beverage
including grain must not be used (may result in failure).
23
Suggestions on food storage
Storing Food
Storing Food
• Do not store food which goes bad easily at low
temperature, such as banana, and melon.
• Allow hot food to cool prior to storing. Placing hot
food in the fridge-freezer could spoil other food, and
lead to higher electric bills.
• When storing the food, use a container with a lid. This
prevents moisture from evaporating, and helps food to
keep its taste and nutrients.
• Do not block air vents with food. Smooth circulation of
cold air keeps fridge-freezer temperature even.
• Do not open the door frequently. Opening the door
lets warm air enter the fridge-freezer, and cause
temperature to rise.
• To adjust the temperature control easily, do not store
food near the temperature control dial.
• Never keep too many foods in door rack, as this may
stop the door from fully closing.
• Do not store bottles in the freezer compartment - they
may break when frozen.
• Do not refreeze food that has been thawed. This
causes loss of taste and nutrition.
Note
If you keep the fridge-freezer in a hot, and humid
place, frequently open its door or put a lot of
vegetables in it, dew may form in it, which has no
effect on its performance.
Remove the dew with dust cloth free from care.
2
Care and Maintenance
General Information
Power Failure
• 1~2 hour power failure does no harm to the foods
stores. Try to avoid opening and closing the door too
frequently.
• Take out foods from the fridge-freezer and firmly fix
the loose items with tape.
• Turn the leveling screws until they stop before moving
the fridge-freezer. Otherwise the screw may scratch
the floor or the fridge-freezer cannot move.
If You Move
Anti
Condensation
Pipe
• The Anti-Condensation
Anti-Condensation
Pipe
pipe is installed around the
front side of fridge-freezer
as well as on the partition
between fridge
compartment and freezer
compartment to prevent
dewing.
• Especially after installation
or when ambient
temperature is high, the fridge-freezer may feel hot,
which is quite normal.
Lamp Replacement
Use a DC12V 0.75W LED lamp broad.
If LED lamp is damaged,it should be replaced
by the service center in stead of on your own.
•
25
Lamp
Care and Maintenance
Cleaning
Before Cleaning
Be sure to unplug the power.
Exterior
Clean the outside of the fridge-freezer with a soft cloth
soaked with hot water or liquid detergent. If you use a
detergent, be sure to wipe it with a clean wet cloth.
Interior
As above.
After Cleaning
Check that the power cord is not damaged, power plug
has not overheated, and that the power plug is tightly
inserted into the outlet.
Be sure to dry the appliance with a cloth after washing
it with water.
Do not use abrasive, petroleum, benzene, thinner,
hydrochloride acid, boiling water, rough brush, etc, as
they may damage parts of the fridge-freezer.
2
Care and Maintenance
GRILLE and DRIP
TRAY
Remove the GRILLE , wipe moisture out around the DOOR
part and the DRIP TRAY using a clean cloth.
Exterior Dispenser
Wipe moisture etc out outside of Dispenser and on the
DISPENSER PAD using a cloth.
WATER TANK
1. Lift the WATER TANK up by pressing the fixing LEVER
on the bottom of WATER TANK and then remove it.
2. After removing the CAP TANK (BIG), clean and fully
rinse the inside/outside part of the WATER TANK by
using neutral cleansing agent.
CAP TANK
(Big & Small)
Clean and fully rinse the CAP TANK (Big & Small) by using
neutral cleansing agent.
Especially for the groove part of the CAP TANK, it is
convenient to cleanse it by using a small brush.
Clean and fully rinse the VALVE ASSEMBLY by using a
small brush. Rinse it while operating the bottom part of
the valve assembly. Always fix the Sealing Rubber
separated for cleansing at the existing position
(may result in water leakage).
VALVE ASSEMBLY
27
Trouble Shooting
Trouble Shooting
Before calling for service, check this list.
It may save you both time and expense.
This list includes common occurrences that are not
the result of defective workmanship or materials in
this appliance.
Possible Causes
Problem
Fridge-Freezer
does not operate
• Power plug may be unplugged from the electric
outlet.
Plug it in securely.
• House fuse has blown or circuit breaker has
tripped.
Check and/or replace fuse and reset circuit breaker.
• Power cut.
Check house lights.
Fridge or Freezer
Compartment
Temperature too
warm
• Temperature control not set on proper position.
Refer to Temperature Control section.
• Appliance is placed close to heat source.
• Warm weather-frequent door openings.
• Door left open for a long time.
• Package holding door open or blocking air duct in
freezer compartment.
Vibration or
Rattling or
Abnormal Noise
• The floor on which the fridge-freezer is installed
may be uneven or the fridge-freezer may be
unstable.
Make it even by rotating the leveling screw.
• Unnecessary objects placed in the back side of the
fridge-freezer.
Frost or Ice
Crystals on frozen
Food
• Door may have been left ajar or package holding
door open.
• Too frequent or too long door openings.
• Frost within package is normal.
Moisture forms on
Cabinet Surface
• This phenomenon is likely to occur in a wet space.
Wipe it with a dry towel.
28
Trouble Shooting
Problem
Possible Causes
• Too frequent or too long door openings.
• In humid weather, air carries moisture into fridge
when doors are opened.
Moisture collects
inside
• Foods with strong odors should be tightly
covered or wrapped.
• Check for spoiled food.
• Interior needs cleaning.
Refer to CLEANING section
Fridge has odor
• Food package is keeping door open.
Move packages that keep door from closing.
• Fridge-freezer is not level.
Adjust the leveling screws.
• The floor on which the fridge-freezer is
installed may be uneven or the fridge-freezer
may be unstable.
Slightly raise the front side with the leveling screw.
Door not closing
properly
• No power at outlet.
• Light lamp needs replacing.
Refer to the Lamp Replacement section
Interior light does
not work
Disposal of your old appliance
1. When this crossed-out wheeled bin symbol is attached to a
product it means the product is covered by the European
Directive 2002/96/EC.
2. Al l electrical and electronic products should be disposed of
separately from the municipal waste stream via designated
collection facilities appointed by the government or the local
authorities.
3. The correct disposal of your old appliance will help prevent
potential negative consequences for the environment and
human health.
4. For more detailed information about disposal of your old
appliance, please contact your city office, waste disposal
service or the shop where you purchased the product.
29
To Reverse the Doors
Your fridge-freezer is designed with reversible doors,so that they may open from either
the left or right hand side to suit your kitchen design.
Precaution
1. Before reversing the door, first of all,you should take out food and accessories like
shelves or trays which are not fixed in the fridge-freezer.
2. Use Torque Wrench or Spanner to fix or remove the bolt.
3. Do not lay the fridge-freezer down.This will cause problems.
4. Be careful not to drop the doors in disassembling or
3
2 2
assembling.
How to Reverse the Door
1
3
2
1.To separate the door handle
1 of the left side, separate
the door cap 2 and unscrew the screw 3 in counterclockwise
direction.Separate the door handle 4 of the freezer in the
same order.
4
6
5
2.After unscrewing the screw
7
of the right hinge cover 5
on the top, separate the right hinge cover 5 to separate
the connecting cable 9 .Separate the bolt 7 fixating the
upper right hinge 8 , and carefully separate the refrigerator
door 10 . Remove the left cover 19 .
6
9
8
19
10
12
13
3.After separating the upper left cap 11
of the separated
refrigerator door 10 , carefully take off the top cap 12 and
pull the cable 13 to connect to the hole on the leftside.
Set the separated top cap 12 at the regular position and
set the cap 11 on the cable hole on the right side. Loosen
the screw 32 44 under the cold room door 10 , move it
to the left of the stopper 31 43 , and then connect it.
11
10
18
40
38
14
39
16
30
32
44
4.Use a sharp gimlet or knife to disconnect the cap 15 from
the cover front 14 , loosen the screw 16 , and then move
the cable 18 to the left to be mounted. Disconnect the cable
40 and the door switch 38 from the disconnected cover front
14 , swap the position of the disconnected cable 40 and door
switch 38 with the cap 39 , mount them, fix them with the
screw 16 , and then install the cap 15 .
31
43
15
35
5. Loosen the bolt 20 of the Hinge Middle 21
, remove the Hinge
Middle 21, and lift up the freezer door 30 to separate it.
(When separating the refrigerator door, separate the bush 35
together.)Separate the hinge cover 24 and set it on the separated
part of middle hinge 21. After unscrewing the screw connected
to the bottom cover 25 connect the cover cap 26 on the right side.
Loosen the bolt 27 connected to the lower hinge 28 . Unscrew
the screw 32 44 fixating the door stopper 31 43 at the
bottom of the freezer door 30 ,and fixate it on the hole on
the left side with the door stopper 31 43 .and then ,move
the upper cap 33 to the right and cover it.
22
23
21
20
24
33
28
27
30
26
43
31
32
44
25
6. Set the separate lower hinge 28 and put it in the bag,take
out the lower left hinge 45 of the bag and set the lower
left hinge 45 on the bottom hole of the left side of the
freezer then tighten the bolt 27 .After fixating the bottom
cover 25 at the regular position,align the freezer door 30
on the pin of lower hinge 45 to attach it properly. Turn over
the separated middle hinge 21 and sheet hinge 22 to
assemble them. And set the bush 35 and washer 23 together
to tighten the bolt 20 . (When tightening the bolt, be
careful not to cause an scratch on the cap decor on top of
the freezer door).
21
20
30
45
27
25
7. After assembling the door by aligning the hinge hole on the
6
36
bottom of the refrigerator door 10 and the pin of the
middle hinge 21 , take out the upper left hinge cover 36
and the left hinge 37 of the bag, After connecting the cable 9 ,
tighten the bolt 7 to screw the screws 6 to the left hinge
cover 45 Take the right cap 42 out of the bag and clean up the
wire, then install it on the right side of the refrigerator top.
42
7
37
9
10
41
8. Move the separated door handle 1
to the right and fixate the
screw 3 on the right position to attach the door cap 2 .Move
the door cap 41 on the right side to the left and attach it. Attach
the freezer door handle 2 in the same method as the refrigerator
door handle 1 .
Note
Reversing the doors is not covered by the warranty.
31
3
2
41
3
2
Memo
Download PDF