ILB-CP05 - Iota Engineering
ILB-CP05
CONSTANT POWER LED EMERGENCY DRIVER
PRODUCT SPECIFICATION SHEET
MODEL NO:
TYPE:
PROJECT:
LED OPERATION:
5W LED Load @ 10-60 VDC nom.1
OUTPUT:
5 Watts (Constant)
DESCRIPTION
The ILB-CP05 from IOTA Engineering is a UL Listed and Classified LED emergency
driver that allows the same LED fixture to be used for both normal and emergency operation. In the event of a power failure, the ILB-CP05 switches to the emergency mode
and operates the existing fixture for 90 minutes. The unit contains a battery, charger,
and converter circuit in a single can and is available in different mounting configurations
for individual fixture requirements. The ILB-CP05 will operate an LED array load at
5 watts with constant power at a rated output voltage of 10V-60V. The Constant
Power design of the ILB-CP05 maintains the output wattage to the LED array even as
the system voltage diminishes.
PRODUCT ADVANTAGES
Listed and Classified for field installation
Constant Power Design maintains illumination throughout the 90-minute runtime with
no light degradation
Two-wire universal AC input
Self-sensing output voltage allows the CP
Series to operate various product types, such
as downlights, troffers, or strips, reducing
product SKUs for emergency options.
SPECIFICATIONS
Input Voltage.......................................................... (Universal) 120-277VAC, 50/60Hz
Input Rating (120/277)........................................................................ 2.7 Watts (max)
FEATURES
Output Voltage1 ............................................................ 10-60VDC Class 2 Compliant
UL 924 Listed, UL Listed and Classified to FTBV
Output Current................................................... 0.5A (@10VDC) - 0.08A (@60VDC)
UL 1310 Certified, Output Class 2 Compliant
Output Power.................................................................................. 5 Watts (constant)
Six mounting configurations available
Power Factor ...................................................................................................... ≥ 0.9
Emergency Operation................................................................................ 90 minutes
Operating Temp.......................................................................................... 0° to 55° C
THD .................................................................................................................. < 20%
Battery..............................................................................High Temp Nickel-Cadmium
24 Hour Recharge
7-10 Year Life Expectancy
Long life high temperature recyclable
Ni-Cad battery
Galvanized steel case
Includes single-piece TBTS test switch and
charge indicator accessory kit
For use with switched or unswitched fixtures
Weight................................................................................................ (-A, -R) 3.0 lbs.
(-B, -TM) 2.5 lbs. (-J, -R-J) 2.75 lbs.
5-Year Warranty. See Warranty Page
for details.
Approval ............................................................................... UL Listed and Classified
for factory and field installation
Meets or exceeds all NEC, IBC, and Life Safety
Code Emergency Lighting Requirements
Rated for use in Plenum, Damp Location, Recessed
Type IC, and Enclosed and Gasketed Luminaires
Max. output voltage in emergency mode is 58.5 VDC
with a + tolerance of 1.5 volts
1
DIMENSIONS
RoHS Compliant
9.5″ x 2.375″ x 1.5″ (mounting center 9.0″)
IOTA REV 072116
Patented. See www.iotaengineering.com/patents for details.
IOTA ENGINEERING PO BOX 11846 TUCSON, AZ 85734
Product specifications are subject to change without notice
TEL: 1-800-866-IOTA (4682) FAX: (520) 741-2837 WEB: www.iotaengineering.com
LED
COMMENTS:
ILB-CP05
ILB-CP05 SAMPLE SPECIFICATION
CONSTANT POWER LED EMERGENCY DRIVER
TEST KIT CONFIGURATION
Supply and install IOTA [Insert 5W model number] Constant Power emergency LED driver
system as indicated on the plans. The emergency driver shall be designed for [Select “Internal”
or “External”] mounting to the luminaire including a self-contained, high-temperature, sealed,
maintenance-free nickel cadmium battery rated for a 10-year service life. The unit shall be
provided complete with an illuminated push to test switch. The emergency driver system shall
be UL class 2 certified in accordance with UL 1310 and shall be UL listed for use in damp
locations and in enclosed and gasketed fixtures with a temperature range of 0° to 55° C.
ORDERING GUIDE
ILB-CP05-
A
Dual Flex
FLEXIBLE CONDUIT TO
FIXTURE (24”)
FLEXIBLE CONDUIT TO
TEST ACCESSORIES (24”)
The unit charger shall consist of a two-stage charging system which samples the battery in
relation to its temperature, state of charge and input voltage fluctuations. The charger shall
be current limited, temperature compensated, short-circuit protected with reverse polarity
protection. A low voltage battery disconnect (LVD) circuit shall be provided and will disconnect the load and circuitry from the battery when it reaches approximately 80 to 85% of its
nominal terminal voltage, preventing a non-recoverable, deep-discharge condition as well
as equipment initialization failure when utility power is restored. The unit shall achieve a full
recharge in 24-hours.
Integral Non-Flex
B
WIRING TO FIXTURE AND
TEST ACCESSORIES
J
The emergency driver shall accommodate an LED load with a forward voltage requirement
ranging from 10 to 60 VDC. The output voltage sensing shall be automatic and instantaneous
with a resulting, inversely-proportional current to maintain constant power to the LED array
with an output tolerance of +/- 3%. The unit shall supply the rated load for a minimum of
1 1/2 hours or to 87 1/2% of rated battery terminal voltage. The output power to the LED
load during emergency operation shall be held constant 5 watts from minute one throughout
the entire emergency run time resulting in no loss or degradation of the light source during
emergency operation.
Single Flex Junction Box Mount
FLEXIBLE CONDUIT TO
TEST ACCESSORIES (36”)
R
The AC input shall be a two-wire, universal voltage capable 120 thru 277 VAC, 50/60 Hz and
be UL Listed to Category Control Number (CCN) FTBR, Emergency Lighting and Power
Equipment, and FTBV, Emergency Light-Emitting-Diode Drivers for field installation. Maximum
input power of the emergency driver shall be 2.7 watts.
WIRING TO
FIXTURE
The unit shall be furnished with an electronic, AC-lockout circuit which will connect the battery when the AC circuit is activated, and an electronic brownout circuit which will enable a
transfer to emergency operation when utility power dips below an acceptable level. Maximum
remote mounting distance of the emergency driver shall be 50-feet.
Dual Flex w/ Reflector-Mount TBTS
FLEXIBLE CONDUIT TO
TEST ACCESSORIES (24”)
FLEXIBLE CONDUIT TO
FIXTURE (24”)
SPECIFICATION TOOLS FOR UL LISTED FIELD INSTALLATION
R-J Single Flex w/ Reflector-Mount TBTS
FLEXIBLE CONDUIT WITH
TEST ACCESSORY (24”)
The ILB-CP05 is UL Listed and Classified for Field
Installation. Refer to the “CP Series Compatibility and
Suitability of Use Guidelines” addendum for complete
project installation requirements.
WIRING TO
FIXTURE
IOTA ILB-CP PERFORMANCE CALCULATOR
TM
Visit www.iotaengineering.com/cptools to access our
on-line CP performance calculator for assistance when
determining lumen output and operating specifications for
your unit, in addition to convenient links to other specification materials.
Top-Mount Non-Flex
WIRING TO FIXTURE AND
TEST ACCESSORIES
ACCESSORIES
TMK-80 Top Mount Cover
TMK
TBMK T-Grid Mounting Kit
RME1 Remote Mounting Enclosure
ILB-CP
ENCLOSURE
LID
CEILING
GRID
ILB-CP
TBMK
BAR
When top-mounting “B” configuration ILB-CP
units, the TMK-80 is used to cover the exposed wiring that goes from the battery pack
into the fixture.
IOTA REV 072116
ILB-CP
MOUNTING
CLIPS
FIXTURE
RME1
Use the TBMK mounting kit to remote mount
flexed units within a grid ceiling. The ILB-CP is
secured to the bars of the TBMK via mounting
clips. The bars then mount to the T-bars of the
ceiling grid. The flexible conduit of the ILB-CP
connects to the fixture.
FLEX TO
FIXTURE
The RME1 enclosures accepts “B” configuration
ILB-CP units for remote mounting. The ILB-CP is
secured within the enclosure and wiring is routed
through the 2 ft. of flexible conduit for connecting
to the fixture. Can be used in conjunction with the
TBMK for grid ceiling mounting.
Patented. See www.iotaengineering.com/patents for details.
IOTA ENGINEERING PO BOX 11846 TUCSON, AZ 85734
TEL: 1-800-866-IOTA (4682) FAX: (520) 741-2837 WEB: www.iotaengineering.com
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising