Axxess XIA-USB Installation Instructions Manual

Add to my manuals
8 Pages

advertisement

Axxess XIA-USB Installation Instructions Manual | Manualzz

USB INTERFACE

XIA-USB

INSTALLATION INSTRUCTIONS

The Axxess XIA-USB is a digital interface designed to play the audio from the USB memory stick while being used in two separate scenarios; 1) in conjunction with an OEM radio and the Axxess XIA-HUB line of digital interfaces or 2) by itself in conjunction with any radio that has an auxiliary audio input jack.

When using the XIA-USB with an OEM radio and the Axxess XIA-HUB digital interfaces, the

OEM radio controls the USB stick. If the OEM radio is Satellite ready then the information on the USB stick (title, artist, etc…) will be displayed on the radios screen. If the OEM radio is not Satellite ready then the optional Axxess XIA-LCD display is required.

When using the XIA-USB by its self with any radio with an auxiliary audio input jack the optional XIA-LCD will be required to control the USB stick and display the information on the USB stick (title, artist, etc…).

Note: Not intended for use with an iPod

* READ IMPORTANT WARNING INSIDE

BEFORE ATTEMPTING ANY INSTALLATION

INTERFACE COMPONENTS

• XIA-USB

• 5’ USB extension cable

• DIN connector to rca’s and power leads

• DIN to DIN Cable

OPTIONAL COMPONENTS

• XIA-LCD

<Line 1>

<Line 2>

ENT

ESC

1-800-221-0932 www.axxessinterface.com

© COPYRIGHT 2009 METRA ELECTRONICS CORPORATION REV. 05-12-09

XIA-USB

* READ IMPORTANT WARNING

BEFORE ATTEMPTING ANY INSTALLATION

* IMPORTANT WARNING

THIS PRODUCT INCLUDES INSTRUCTIONS FOR INSTALLATION WHICH MUST BE CAREFULLY FOLLOWED. THE

INSTRUCTIONS ARE WORDED IN SUCH A MANNER TO ASSUME THAT THE INSTALLER IS CAPABLE OF COMPLETING

THESE TYPE OF ELECTRONIC INSTALLATIONS. IF YOU ARE UNCLEAR AS TO WHAT YOU ARE INSTRUCTED TO DO OR

BELIEVE THAT YOU DO NOT UNDERSTAND THE INSTRUCTIONS SO AS TO PROPERLY AND SAFELY COMPLETE THE

INSTALLATION YOU SHOULD CONSULT A TECHNICIAN WHO DOES HAVE THIS KNOWLEDGE AND UNDERSTANDING.

FAILURE TO FOLLOW THESE INSTRUCTIONS CAREFULLY AND TO INSTALL THE INTERFACE AS DESCRIBED COULD

CAUSE HARM TO THE VEHICLE OR TO SAFETY SYSTEMS ON THE VEHICLE. INTERFERENCE WITH CERTAIN SAFE-

TY SYSTEMS COULD CAUSE HARM TO PERSONS AS WELL.

IF YOU HAVE ANY QUESTIONS IN THIS REGARD PLEASE CALL THE HELP LINE OR METRA AT:

1-800-221-0932 FOR ASSISTANCE.

K

NOWLEDGE IS

P

OWER

Enhance your installation and fabrication skills by enrolling in the most recognized and respected mobile electronics school in our industry.

Log onto www.installerinstitute.com or call

800-354-6782 for more information and take steps toward a better tomorrow.

XIA-USB

TOOLS REQUIRED FOR INSTALLATION

• Cutting Tool • Tape • Crimping Tool

• Connectors (ie: butt-connectors, bell caps, etc.)

CONNECTING THE XIA-USB

* Important: Before beginning any of the following, disconnect the negative battery terminal to prevent accidental short circuit.

The XIA-USB can be used in two different configurations, either with the XIA-HUB line of Axxess interfaces or by itself as a stand alone unit. Below we will describe each configuration:

CONNECTING THE XIA-USB TO AN OEM RADIO WITH THE

XIA-HUB INTERFACE

Note: The Axxess XIA-LCD will be required if your radio cannot display text or is not satellite ready.

* Note: The DIN to rca’s and power leads will not be used in this application

A

XIA-USB

XIA-LCD

ENT

ESC

USB EXTENSION CABLE

20 WAY MOLEX

HARNESS

20

WA

Y

TO USB MEMORY STICK

8 PIN DIN TO 8 PIN DIN CABLE

XIA-HUB

1. Remove radio from dash and connect the Axxess XIA-HUB to your vehicle per the instructions it came with.

2. Using the 8 pin DIN to 8 pin DIN cable supplied with the XIA-USB, connect one end to the center port of the

XIA-HUB interface.

(Figure A)

3. Connect the other end of the 8 pin DIN to 8 pin DIN cable to the 8 pin port of the XIA-USB (Figure A)

Continued on page 2.

1

XIA-USB

4. Connect the male end of the USB extension cable to the USB port of the XIA-USB.

(Figure A)

5. Run the USB extension cable to a location that would be easy to plug the USB memory stick into.

* If the radio is satellite ready or can display text, skip to step 8

*If the radio is not satellite ready or cannot display text, the XIA-LCD will be required; continue on to step 6

6. Find a suitable mounting location for the XIA-LCD on the dash, somewhere that is visible to the driver and within reach.

7. Plug the end of the XIA-LCD into the 4 pin port on the XIA-HUB interface, not in the XIA-USB.

(Figure A)

8. Plug the 20 way Molex harness back into the XIA-HUB interface.

(Figure A)

9. Cycle the key by turning the ignition on, off, then back on again to initialize the interface.

Follow the instructions in the Axxess XIA-HUB interface for operation instructions of the XIA-USB.

CONNECTING THE XIA-USB BY ITSELF TO ANY RADIO THAT HAS AN

EXISTING AUXILIARY INPUT JACK (I.E. 3.5MM JACK ON FACE OF

RADIO, AUXILIARY INPUT INTERFACE THAT PLUGS INTO THE BACK OF

THE RADIO, FM MODULATOR)

THE USE OF THE XIA-LCD IS REQUIRED IN ORDER TO CONTROL THE

MUSIC AND SEE THE INFORMATION ON THE USB MEMORY STICK.

* Note: The DIN to DIN cable is not used in this application

B

XIA-USB

RCA’S - TO AFTERMARKET

RADIO AUX IN

TO USB MEMORY STICK

RED WIRE -TO 12V SWITCHED ACCESSORY

BLACK WIRE -TO GROUNDING POINT

ENT

ESC

XIA-LCD

1. Remove radio from dash.

2. Take the XIA-USB and plug in the supplied 8 pin DIN to rca/power cable.

(Figure B)

2

Continued on page 3.

XIA-USB

3. Plug the rca’s from the XIA-USB into the aftermarket radio’s AUX in.

If the radio does not have an AUX in the use of an fm modulator like the Axxess AFM-MOD will be required.

4. Connect the Red wire of the XIA-USB to a 12 volt switched accessory wire.

(Figure B)

5. Connect the Black wire of the XIA-USB to a good grounding point.

(Figure B)

6. Find a suitable mounting location for the XIA-LCD on the dash, somewhere that is visible to the driver and within reach.

7. Plug the end of the XIA-LCD into the 4 pin port on the XIA-USB.

(Figure B)

8. Connect the male end of the USB extension cable to the USB port of the XIA-USB.

(Figure B)

9. Run the USB extension cable to a location that would be easy to plug the USB memory stick into.

CONTROLLING THE XIA-USB BY ITSELF WITH THE XIA-LCD

Once all connections are made to the XIA-USB, turn the vehicle on. Every time the vehicle is turned on the display of the XIA-LCD will show letters and numbers for a couple of seconds then go away. This is normal.

1. Plug the USB stick into the USB cable.

2. Turn the radio on to AUX in mode. If you are using an fm modulator tune your radio to the appropriate FM station.

3. Press the ENT button on the XIA-LCD to start playing music.

* Note: The XIA-USB will play folders in the USB stick in alphabetical order.

4. Pressing the up arrow will go to the next song.

5. Pressing the down arrow will go to the previous song.

6. Pressing the ESC button will open the folder menu.

The folder menu is as follows:

A) Next Folder: Goes to next folder alphabetically.

B) Previous Folder: Goes to the previous folder.

C) + 10 Songs: Skips forward 10 songs.

D) - 10 Songs: Goes back 10 songs.

E) + 10 Folders: Skips forward 10 folders alphabetically.

F) - 10 Folders: Goes back 10 folders.

G) Play: Starts playing song from pause mode.

H) Pause: Pauses song.

7. Pressing the ENT button it will select the choice selected in the folder menu.

8. Press the ESC button to exit the folder menu and show the song information.

3

XIA-USB

NOTES

4

XIA-USB

NOTES

5

XIA-USB INSTRUCTIONS

1-800-221-0932 www.axxessinterface.com

REV. 05/12/09 © COPYRIGHT 2008-2009 METRA ELECTRONICS CORPORATION INSTXIA-USB

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement