Password setting for the child lock (for TV input mode) Watching TV

Password setting for the child lock (for TV input mode) Watching TV
Watching TV
Password setting for the child lock (for TV
input mode)
Allows you to use a password to protect certain
settings from being accidentally changed.
Setting a password
Register a 4-digit password number to use the Child
Lock function.
1
Press MENU and the MENU screen displays.
2
Press c/d to select “Setup”.
3
Press a/b to select “Child Lock”, and then
press ENTER.
4
If you already set the password, enter it here.
5
Press a/b to select “Change password”, and
then press ENTER.
Reset
Allows you to reset your password.
1
Repeat steps 1 to 4 in Setting a password.
2
Press a/b to select “Clear password”, and
then press ENTER.
3
Press c/d to select “Yes”, and then press
ENTER.
Change password
Clear password
Yes
No
NOTE
• As a precautionary measure, make a note of your
password on the back of this operation manual, cut
it out and keep it in a safe place that children cannot
reach.
• This function is only available for TV input mode.
• If you want to enable the channel lock function, see page
21.
Change password
Clear password
New Password
– – – –
Reconfirm
– – – –
6
Enter the 4-digit number as a password using
0 – 9.
7
Enter the same 4-digit number as in step 6 to
confirm.
NOTE
• To view a locked channel you must enter a password.
When you select a locked channel, a password prompt
message pops up.
• Press ENTER to display the password input window.
25
40G100H_en.indd
25
2009-12-17
14:15:58
Watching TV
Energy conservation settings
Auto power-off at a designated time
This function is conveniently used when, for instance,
going to bed while watching TV.
1
Auto power-off after the end of broadcast
You can set the TV to automatically power off in about
15 minutes after the TV goes into a state of receiving
no programme signals, such as the end of a broadcast
day.
1
Press MENU and the MENU screen displays.
2
Press c/d to select “Power Control”.
3
Press a/b to select “No Signal Off”, and then
press ENTER.
4
Press c/d to select “Enable”, and then press
ENTER.
Press SLEEP.
• Remaining time displays when sleep timer has
been set.
• Five minutes before the power shuts down, the
remaining time displays every minute.
Sleep Timer: Remain 2 hr. 00 min.
2
Each time you press SLEEP, the remaining
time switches as shown below.
Off
0 hr. 30 min.
1 hr. 00 min.
2 hr. 30 min.
2 hr. 00 min.
1 hr. 30 min.
NOTE
• When the time has been set, countdown automatically
starts.
• Five minutes before the preset of time expires, the
remaining time displays each minute.
• Select “Off” by pressing SLEEP to cancel the sleep timer.
NOTE
• “Disable” is the factory preset value.
• When a TV programme finishes, and the TV receives signal
input, this function may not operate.
Auto power-off when there are no
operations performed
You can set the TV to automatically power off when no
TV operation is performed for more than an hour.
1
Press MENU and the MENU screen displays.
2
Press c/d to select “Power Control”.
3
Press a/b to select “No Operation Off”, and
then press ENTER.
4
Press a/b to select “30 min.”, “3 hr.” or
“Disable”.
• Five minutes before the power shuts down, the
remaining time displays every minute.
NOTE
• “Disable” is the factory preset value.
26
40G100H_en.indd
26
2009-12-17
14:16:00
Watching TV
Power Management
Picture size settings
You can set the TV to automatically power off when no
image is displayed on PC.
1
Press MENU and the MENU screen displays.
2
Press c/d to select “Power Control”.
3
4
WSS allows a television to switch automatically among
the different screen formats.
1
Press MENU and the MENU screen displays.
Press a/b to select “Power Management”,
and then press ENTER.
2
Press c/d to select “Setup”.
Press c/d to select “On” or “Off”, and then
press ENTER.
3
Press a/b to select “WSS”, and then press
ENTER.
4
Press c/d to select “On” or “Off”, and then
press ENTER.
On
Off
NOTE
• After setting the Energy Save mode to “On”, if no signal is
input for about 8 minutes, the power will be turned off.
• Even if you start using the PC and the signal inputs again,
the TV stays off.
• The TV turns on again by pressing POWER. (See page 13.)
• 5 minutes before the power turns off, the remaining time is
displayed at one-minute intervals.
Ecology
When set to “Yes”, the TV activates the following
power saving mode.
•
•
•
•
Selecting the Wide Screen Signalling
(WSS) picture size automatically
“Standby Mode” set to “Mode 2” (Page 24)
“No Signal Off” set to “Enable” (Page 26)
“No Operation Off” set to “3 hr.” (Page 26)
“Power Management” set to “On” (Page 27)
1
Press MENU and the MENU screen displays.
2
Press c/d to select “Power Control”.
3
Press a/b to select “Ecology”, and then
press ENTER.
4
Press c/d to select “Yes”, and then press
ENTER.
NOTE
• Try to set WIDE mode if an image does not switch to the
correct screen format. When the broadcast signal contains
no WSS information, the function will not work even if
enabled.
• When receiving weak or unstable signals and for avoiding
wrong estimation of the signals, it is recommended to set
WSS to “Off”.
Selecting the Wide Screen Signalling
(WSS) picture size manually
The WSS signal has 4:3 auto-switching that allows you
to select between Panorama and Normal.
1
Press MENU and the MENU screen displays.
2
Press c/d to select “Setup”.
3
Press a/b to select “4:3 Mode”, and then
press ENTER.
4
Press c/d to select “Panorama” or “Normal”,
and then press ENTER.
WSS signal 4:3 screen
NOTE
• Ecology mode cannot be deactivated by selecting “No”.
Each setting must be changed individually to deactivate
Ecology mode.
Identification
The software version can be look over.
4:3 mode “Panorama”
Selected item
4:3 mode “Normal”
Description
Panorama
Wide image without side bars
Normal
Normal range keeping 4:3 or 16:9 aspect
ratio
27
40G100H_en.indd
27
2009-12-17
14:16:01
Watching TV
Selecting the picture size manually (for TV/AV input mode)
Manual Selection
You can select different picture sizes that account for
the kind of each picture.
Auto Selection
If you set “WSS” and “4:3 Mode” in the Setup menu
on page 27, the optimum WIDE mode is automatically
chosen for every broadcast containing the WSS
information.
“WSS” menu
To enable Auto Selection, set “WSS” in the Setup
menu to “On”. (See page 27.)
1
Press WIDE.
• The “WIDE MODE” menu displays.
• The menu lists the wide mode options selectable
for the type of video signal currently received.
“4:3 Mode” menu
To set the type of the wide screen, select “Panorama”
or “Normal” in the 4:3 Mode menu. (See page 27.)
WIDE MODE
Normal
Zoom 14:9
4:3 Mode set to “Panorama”
4:3 Mode set to “Normal”
Panorama
Full
NOTE
• If the broadcast signal contains no WSS information, Auto
Selection will not function even when the WSS option is
enabled.
Cinema 16:9
Cinema 14:9
2
Press WIDE or a/b while the “WIDE MODE”
menu displays on the screen.
• As you toggle down the options, each mode is
immediately reflected on the TV.
Selected item
Normal
Zoom 14:9
Panorama
Full
Cinema 16:9
Cinema 14:9
Underscan
Description
For 4:3 “standard” pictures. A side bar appears on each side.
For 14:9 letterbox pictures. A thin side bar appears on each side, and you may also see bars on
the top and bottom with some programmes.
In this mode the picture is progressively stretched toward each side of the screen.
For 16:9 squeeze pictures.
For 16:9 letterbox pictures. Bars may appear on the top and bottom with some programmes.
For 14:9 letterbox pictures. Bars may appear on the top and bottom with some programmes.
Display with an “Underscan” image only when receiving a 720p signal. Display with the HighDefinition image adjusted optimally. Noise may appear on the edge of the screen with some
programmes.
Normal
Zoom 14:9
Panorama
Cinema 14:9
Cinema 16:9
Full
NOTE
• Some picture sizes may not be
displayable depending on the
input signal.
28
40G100H_en.indd
28
2009-12-17
14:16:02
Watching TV
Selecting a preset AV MODE
The “AV Mode” function enables you to select
appropriate settings for audio and video to account for
the system environment which can vary due to factors
like room brightness, type of programme watched or
the type of image input from external equipment.
Using “AV Mode” on the remote control unit
1
Press AV MODE.
• Present AV Mode displays.
2
Press AV MODE again before the mode
displayed on the screen disappears.
• The mode changes as shown below.
AV Mode: STANDARD
AV Mode: MOVIE
AV Mode: DYNAMIC
AV Mode: GAME
AV Mode: DYNAMIC(FIXED)
AV Mode: PC
Selected item
Description
STANDARD
For a highly defined image in a normally
bright room.
MOVIE
For a movie.
GAME
Lowers image brightness for easier
viewing.
PC
For PC. (Available only when inputting an
HDMI or PC signal.)
USER
Allows the user to customise settings as
desired. You can set the mode for each
input source.
DYNAMIC
(FIXED)
Changes the image and sound settings to
the factory preset values. No adjustments
are allowed.
DYNAMIC
For a clear-cut image emphasising high
contrast for sports viewing
NOTE
• You can select a different AV Mode item for each input
mode. (For example, select “STANDARD” for TV input and
“DYNAMIC” for VIDEO input.)
• During PC input mode, only “STANDARD”, “PC” and
“USER” can be selected under the “AV Mode” selection.
AV Mode: USER (TV)
Using “AV Mode” on the menu screen
1
Press MENU and the MENU screen displays.
2
Press c/d to select “Picture”.
3
Press a/b to select “AV Mode”, and then
press ENTER.
4
Press a/b to select the desired item, and
then press ENTER.
29
40G100H_en.indd
29
2009-12-17
14:16:04
Watching TV
Manual picture settings
Selected item
Picture adjustment
OPC
Sets whether or not the screen brightness
is automatically adjusted according to
the lighting condition in the room. (OPC
setting: See this page.)
Backlight
The screen dims
The screen
brightens
Contrast
For less contrast
For more contrast
Brightness
For less brightness
For more
brightness
Colour
For less colour
intensity
For more colour
intensity
Tint
Skin tones become
purplish
Skin tones become
greenish
Sharpness
For less sharpness
For more
sharpness
Advanced
For finer picture adjustments. (See page
31)
Reset
Resets all picture adjustment items to the
factory preset values.
You can adjust the picture to your preference.
Follow the steps to adjust the picture.
1
Press MENU and the MENU screen displays.
2
Press c/d to select “Picture”.
MENU
[Picture]
Picture
Audio
AV Mode
c button
d button
[STANDARD]
OPC
[Off]
Backlight
[+16] –16
Contrast
[ 30]
+16
0
40
Brightness [
0] –30
+30
Colour
[
0] –30
+30
Tint
[
0] –30
+30
Sharpness [
0] –10
+10
w OPC (Optical Picture Control) setting
You can set the TV to automatically adjust the screen
to suitable backlight brightness according to the
lighting conditions.
Advanced
Reset
3
Press a/b to select the desired menu item.
Press ENTER to proceed if necessary.
4
Press a/b or c/d to select the desired item
or adjust the item to the desired level. Press
ENTER if necessary.
NOTE
• For resetting all adjustment items to factory preset values,
press a/b to select “Reset”, press ENTER, press c/d
to select “Yes”, and then press ENTER.
• When “OPC” is set to “On:Display” or “On”, even if
“Backlight” is adjusted, “OPC” is off automatically.
• Select “Advanced” and then press ENTER to set “Colour
Temp.”, “Film Mode”, “Black”,“3D-Y/C”, “Monochrome” or
“DNR”. (See page 31)
POWER
OPC sensor
Using OPC on the menu screen
Selected item
Description
On:Display
Displays the OPC effect on the screen
while adjusting the brightness of the
screen.
On
Automatically adjusts.
Off
The brightness is fixed at the value set in
“Backlight”. (See this page.)
NOTE
• Make sure no object obstructs the OPC sensor, which
could affect its ability to sense surrounding light.
• The OPC may not work when the light in the surround is
too bright or too dark, only the change of the light occurred
that the OPC (the icon of the greenery) will be displayed.
30
40G100H_en.indd
30
2009-12-17
14:16:05
Watching TV
Advanced picture settings
The advanced settings enable you to set the picture
adjustment in more detail. There are six options you
can choose from.
1
Press MENU and the MENU screen displays.
2
Press c/d to select “Picture”.
w 3D-Y/C
Provides high quality images with minimal dot crawl
and cross colour noise.
Selected item
3
Press a/b to select “Advanced”, and then
press ENTER.
4
Press a/b to select the desired menu, and
then press ENTER.
5
Press a/b or c/d to select the desired level,
and then press ENTER if necessary.
w Colour Temp. (Colour Temperature)
Adjusts the colour temperature to give the best white
image.
Description
Standard
Normal adjustment
Fast
For movie image
Slow
For still image
Off
3D-Y/C off
NOTE
• 3D-Y/C is not selectable depending on the input signal
type.
• 3D-Y/C may not operate depending on the input signal
type or noisy input signal.
w Monochrome
For viewing images in monochrome.
1
Press MENU and the MENU screen displays.
White with bluish tone
2
Press c/d to select “Picture”.
White with reddish tone
3
Press a/b to select “Advanced”, and then
press ENTER.
w Film Mode
4
Press a/b to select “Monochrome”, and then
press ENTER.
Automatically detects a film-based source (originally
encoded at 24/25 frames/second, depending on the
vertical frequency), analyses it then recreates each still
film frame for high-definition picture quality.
5
Press c/d to select “On”, and then press
ENTER.
Selected item
High
Mid-High
Middle
Mid-Low
Low
Description
w DNR (Digital Noise Reduction)
w Black
For easier viewing, change the viewing depth by
selecting a level for automatically adjusting the dark
portion of an image.
Selected item
Description
On
For high detail in black portions
Off
No adjustment
Reduces noise on the screen and produces a clear
video image.
1
Press MENU and the MENU screen displays.
2
Press c/d to select “Picture”.
3
Press a/b to select “Advanced”, and then
press ENTER.
4
Press a/b to select “DNR”, and then press
ENTER.
5
Press a/b to select the desired level, and
then press ENTER.
31
40G100H_en.indd
31
2009-12-17
14:16:06
Watching TV
Other picture settings
Game Play Time
Adjusting the image position
For adjusting a picture’s horizontal and vertical
position.
1
Press MENU and the MENU screen displays.
2
Press c/d to select “Setup”.
3
Press a/b to select “Position”, and then
press ENTER.
4
Press a/b to select “H-Position” or
“V-Position”.
H-Position [ 0]
–10
+10
V-Position
–20
+20
[ 0]
Reset
This function displays the elapsed game time so you
do not lose track of the time.
To display the elapsed time, select “GAME” under “AV
Mode” for the input mode of the terminal connected to
the game console before starting the game.
1
Press MENU and the MENU screen displays.
2
Press c/d to select “Option”.
3
Press a/b to select “Game Play Time”, and
then press ENTER.
4
Press c/d to select “On”, and then press
ENTER.
Selected item
Selected item
Description
H-Position
Centres the image by moving it to the left
or right.
V-Position
Centres the image by moving it up or
down.
5
Description
On
When using input 1-6 and the AV Mode
is change to “Game”, the elapsed time is
displayed every 30 minutes.
Off
There is no display.
Press c/d to adjust the item to your desired
position.
NOTE
• For resetting all adjustment items to the factory preset
values, press a/b to select “Reset”, and then press
ENTER.
• Adjustments are stored separately according to input
source.
• Images may not be displayed properly depending on the
settings and/or signals.
32
40G100H_en.indd
32
2009-12-17
14:16:08
Watching TV
Audio adjustment
You can adjust the audio of the selected AV mode.
1
Press MENU and the MENU screen displays.
2
Press c/d to select “Audio”.
Audio
Output Volume Select
Allows you to select what controls the audio output.
1
Press MENU and the MENU screen displays.
2
Press c/d to select “Option”.
3
Press a/b to select “Output Volume Select”,
and then press ENTER.
4
Press c/d to select “Fixed” or “Variable”, and
then press ENTER.
Power Control
STANDARD
Treble
[ 0]
-15
+15
Bass
[ 0]
-15
+15
Balance
[ 0]
L
R
Surround
[Off]
Bass Enhancer
[On]
Reset
3
Press a/b to select the desired menu item.
Press ENTER to proceed if necessary.
4
Press a/b or c/d to select the desired item
or adjust the item to the desired level. Press
ENTER if necessary.
Selected item
c button
d button
Treble
For weaker treble
For stronger treble
Bass
For weaker bass
For stronger bass
Balance
Decrease audio from
the right speaker
Decrease audio
from the left speaker
NOTE
• For resetting all adjustment items to the factory preset
values, press a/b to select “Reset”, press ENTER, press
c/d to select “Yes”, and then press ENTER.
• “Surround” cannot be selected under “DYNAMIC(FIXED)”
for “AV Mode” setting.
Fixed
Selected item
Variable
Description
Fixed
• Sound via speakers is adjusted with
VOL k/l on the remote control unit or
the TV.
• Sound via the 输出 (Output) terminals is
not adjustable and constantly outputs.
Variable
• Sound via the 输出 (Output) terminals is
adjusted with VOL k/l on the remote
control unit or the TV.
• Sound via speakers is muted.
NOTE
• The “Audio” menu cannot be operated when “Variable” is
selected.
w Surround
When you set to “On”, you can enjoy surround sound,
the same as if you were in a movie theatre.
w Bass Enhancer
When “On” is selected, the bass effect is enhanced.
33
40G100H_en.indd
33
2009-12-17
14:16:09
Settings when using external devices
Settings when using HDMI output devices
HDMI terminals can carry audio and visual signals to
the TV with an HDMI certified cable. When you want
to output the audio and picture from an HDMI output
device on the TV, select “INPUT1”/“INPUT2” by
switching the input source.
Connecting an HDMI output device
Audio cables (used only for analogue
audio input) (commercially available)
HDMI
output
device
HDMI Audio Select
1
When “INPUT1” is selected, HDMI audio can
be selected.
2
Press MENU and the MENU screen displays.
3
Press c/d to select “Option”.
4
Press a/b to select “HDMI Audio Select”,
and then press ENTER.
MENU
[Option ... HDMI Audio Select]
Option
HDMI Audio Select
HDMI cable
(commercially
available)
Output Volume Select
[Digital]
[Fixed]
Audio Only
Game Play Time
[Off]
Colour System
Fine Sync.
5
w HDMI (High-Definition Multimedia
Interface) Setting
HDMI Auto View
1
To watch an HDMI equipment image, select
“INPUT1”/“INPUT2” using TV/VIDEO on the
remote control unit or on the TV.
2
Press MENU and the MENU screen displays.
3
Press c/d to select “Setup”.
4
Press a/b to select “HDMI Auto View”, and
then press ENTER.
Press c/d to select the desired item, and
then press ENTER.
HDMI Setup
items
Selectable
items
HDMI Auto
View
Enable/
Disable
HDMI Audio
Select
Digital/
Analogue
Description
Set whether or not to use
“WIDE MODE” based
on signal recognition,
including an HDMI signal.
Select “Digital” for
audio signal via the
HDMI terminal. Select
“Analogue” for audio
signal via the AUDIO jack.
• The HDMI Auto View can be selected only when
“INPUT1”/“INPUT2” is selected.
5
Press c/d to select the items to be set, then
press ENTER to set them.
NOTE
• Refer to your external equipment operation manual for the
above settings.
• When connecting a DVI-HDMI conversion adaptor/cable to
the HDMI terminal, the image may not come in clearly.
34
40G100H_en.indd
34
2009-12-17
14:16:10
Settings when using external devices
Selecting the input source and signal type
Labelling input sources
You can assign each input source a label as you
prefer.
Selecting input source
Can use for selecting the input source.
Using TV/VIDEO on the remote control unit or on
the TV
TV/VIDEO allows you to choose from the available
input sources.
1
Press TV/VIDEO to select the desired input
source.
2
Press MENU and the MENU screen displays.
3
Press c/d to select “Setup”.
4
Press a/b to select “Input Label”, and then
press ENTER.
5
Press a/b/c/d to select letters to label the
input source.
POWER
MENU
TV/VIDEO
CH
VOL
• When you want to change the input label that you
have already assigned to the default name, press
c/d to move to “CLEAR” on the “Input Label”
screen, and then press ENTER.
1
Press TV/VIDEO on the remote control unit or
on the TV.
2
Press TV/VIDEO on the remote control unit or
on the TV to select the input source.
• The image and sound from the selected source
are output on the TV.
• You can also select the input source by pressing
a/b.
6
Repeat the above until the name is fully spelt
out, and then press MENU.
• The name can be 6 characters or less.
• When you want to set an input source name of
less than 6 characters, press MENU to exit from
the labelling menu.
TV
DVD
INPUT2
INPUT3
INPUT4
INPUT5
INPUT6
INPUT7
(Example)
NOTE
• You cannot change labels if the input source is “TV”.
35
40G100H_en.indd
35
2009-12-17
14:16:12
Settings when using external devices
Skipping HDMI/PC input
Colour system settings
This setting allows you to skip the HDMI or PC input
on the “Input Select” menu.
You can change the colour system to one that is
compatible with the image on the screen.
Press MENU and the MENU screen displays.
1
Press MENU and the MENU screen displays.
2
Press c/d to select “Setup”.
2
Press c/d to select “Option”.
3
Press a/b to select “Input Skip”, and then
press ENTER.
3
Press a/b to select “Colour System”, and
then press ENTER.
4
Press a/b to select the “INPUT” you want to
skip, and then press ENTER.
4
Press a/b to select a compatible video signal
system of your equipment, and then press
ENTER.
1
INPUT1 (HDMI)
INPUT2 (HDMI)
Auto
INPUT7 (RGB)
PAL
SECAM
Yes
No
NTSC 3.58
NTSC 4.43
PAL-60
5
Press c/d to select “Yes”, and then press
ENTER.
6
Press MENU to exit.
NOTE
• Factory preset value is “Auto”.
• If “Auto” is selected, colour system for each channel is
automatically set. If an image does not display clearly,
select another colour system (e.g. PAL, NTSC 4.43).
• “Colour System” is selectable only when inputting a
composite signal.
36
40G100H_en.indd
36
2009-12-17
14:16:13
Connecting a PC
Use the PC terminals to connect a PC.
NOTE
• The 输入 7 (INPUT7) (PC input) terminals are DDC1/2B-compatible.
• Refer to page 40 for a list of PC signals compatible with the TV.
Connecting a PC
PC
RGB cable (commercially available)
Ø 3.5 mm stereo minijack cable
(commercially available)
6
Signal names for 15-pin mini D-sub connector
Pin No.
Signal name
R
G
B
Not connected
CSYNC
Pin No.
Signal name
GND (Ground)
GND (Ground)
GND (Ground)
+5V
GND (Ground)
Pin No.
Signal name
Not connected
SDA
HD
VD
SCL
NOTE
• Macintosh adaptor may be required for use for some Macintosh computers.
Displaying a PC image on the screen
To view images from a PC, press PC on the remote
control or use TV/VIDEO on the remote control or
TV/VIDEO on the TV set to select “INPUT7”.
TV
INPUT1
POWER
INPUT2
INPUT3
MENU
INPUT4
TV/VIDEO
CH
INPUT5
INPUT6
INPUT7
VOL
When connecting to a PC, the correct input signal type
is automatically detected. (See page 39.)
NOTE
• Each time TV/VIDEO is pressed, the input source toggles.
37
40G100H_en.indd
37
2009-12-17
14:16:14
Connecting a PC
Selecting the picture size
You can select the picture size as illustrated below.
NOTE
• Connect the PC before making adjustments.
• Selectable picture size may vary with input signal type.
1
Press WIDE.
• The WIDE MODE menu displays.
WIDE MODE
Normal
Full
(Example)
2
Press WIDE or a/b to select a desired item
on the menu.
a
Picture size images.
Input Signal
Normal
Keeps the original
aspect ratio in a full
screen display.
Full
An image fully fills the
screen.
38
40G100H_en.indd
38
2009-12-17
14:16:16
Connecting a PC
Adjusting the PC image automatically
Selecting the input resolution
• Some input signals may have to be set manually to display
properly.
• The pairs of input signals (resolutions) in the list below are
not distinguishable when received. In such case, you have
to set the correct signal manually. After setting once, it will
display when the same signal (resolution) is input again.
1024 x 768
This function enables the screen to be automatically
adjusted to its best possible condition when the
analogue terminals of the TV and PC are connected
with a commercially available RGB cable, etc.
1
Press MENU and the MENU screen displays.
2
Press c/d to select “Option”.
3
Press a/b to select “Fine Sync.”, and then
press ENTER.
4
Press a/b to select “Auto Sync.”, and then
press ENTER.
5
Press c/d to select “Yes”, and then press
ENTER.
1360 x 768
NOTE
• You can only select the “Input Signal” on the Setup menu
when receiving one of the 2 input signals listed above.
1
Press MENU and the MENU screen displays.
2
Press c/d to select “Option”.
3
Press a/b to select “Fine Sync.”, and then
press ENTER.
• Auto Sync. starts.
Input Signal
4
5
Press a/b to select “Input Signal”, and then
press ENTER.
Press c/d to select the desired input signal
on the display, and then press ENTER.
1360 x 768
1024 x 768
Auto Sync.
H-Position
[ 90]
V-Position
[ 60]
Clock
[ 90]
Phase
[
Yes
No
8]
Reset
NOTE
• Auto Sync. is likely to succeed when an input PC image
has wide vertical stripes (e.g. pattern with high contrast
stripes, or cross-hatched).
It may fail when an input PC image is solid (low contrast).
• Be sure to connect the PC to the TV and switch it on
before starting Auto Sync.
(Example)
39
40G100H_en.indd
39
2009-12-17
14:16:17
Connecting a PC
PC compatibility chart
Adjusting the PC image manually
Ordinarily you can easily adjust the picture as
necessary to change image position using Auto Sync.
In some cases, however, manual adjustment is needed
to optimise the image.
1
Press MENU and the MENU screen displays.
2
Press c/d to select “Option”.
3
Press a/b to select “Fine Sync.”, and then
press ENTER.
4
Press a/b to select a specific adjustment
item among “H-Position”, “V-Position”, “Clock”
and “Phase”.
Resolution
Horizontal Vertical
VESA
Frequency Frequency Standard
VGA
640 m 480
31.5 kHz
60 Hz
✓
SVGA
800 m 600
37.9 kHz
60 Hz
✓
XGA
1024 m 768
48.4 kHz
60 Hz
✓
WXGA
1360 m 768
47.7 kHz
60 Hz
✓
SXGA
1280 m 1024
64.0 kHz
60 Hz
✓
DDC is a registered trademark of Video Electronics
Standards Association.
Power Management is a registered trademark of Sun
Microsystems, Inc.
VGA and XGA are registered trademarks of
International Business Machines Corp.
Input Signal
Auto Sync.
H-Position
[90]
+
V-Position
[60]
+
Clock
[90]
+
Phase
[ 8]
+
Reset
Selected item
Description
H-Position
Centres the image by moving it to the left
or right.
V-Position
Centres the image by moving it up or
down.
Clock
Adjusts when the image flickers with
vertical stripes.
Phase
Adjusts when characters have low
contrast or when the image flickers.
5
Press c/d to adjust the item to your desired
position.
NOTE
• For resetting all adjustment items to the factory preset
values, press a/b to select “Reset”, press ENTER, press
c/d to select “Yes”, and then press ENTER.
• Images may not be displayed properly depending on the
settings and/or input signals.
40
40G100H_en.indd
40
2009-12-17
14:16:18
Appendix
Troubleshooting
The problems described below are not always caused by malfunctions. Check the TV again before having the TV
serviced.
Problem
Possible Solution
• No power.
• Check if you pressed POWER on the remote control unit. (See page 13.)
If the indicator on the TV lights up red, press POWER.
• Is the AC cord disconnected? (See page 9.)
• Has the power been turned on? (See page 13.)
• Unit cannot be operated.
• External influences such as lightning, static electricity, etc., may cause improper
operation. In this case, operate the unit after first turning the power off the TV or
unplugging the AC cord and re-plugging it in after 1 or 2 minutes.
• Remote control unit does not
operate.
•
•
•
•
• Picture is cut off.
• Is the image position correct? (See page 32.)
• Are screen mode adjustments such as picture size made correctly? (See pages 27,
28 and 38.)
• Strange colour, light colour, or
dark, or colour shift.
•
•
•
•
•
• Power is suddenly turned off.
• The unit’s internal temperature has increased.
Remove any objects blocking the vent or clean.
• Check the power control setting. (See pages 26 and 27.)
• Is the sleep timer set? (See page 26.)
• No picture.
•
•
•
•
•
•
• No sound.
• Is the volume too low? (See page 18.)
• The TV sometimes makes a
cracking sound.
• This is not a malfunction. This happens when the cabinet slightly expands and
contracts according to changes in temperature. This does not affect the TV’s
performance.
Are batteries inserted with polarity (e, f) aligned? (See page 12.)
Are batteries worn out? (Replace with new batteries.)
Are you using it under strong or fluorescent lighting?
Is a fluorescent light shining on the remote control sensor?
Adjust the picture tone. (See pages 30 to 31.)
Is the room too bright? The picture may look dark in a room that is too bright.
Check the colour system setting. (See pages 20 and 36.)
Check the input signal setting. (See page 39.)
Check the HDMI Setup setting. (See page 34.)
Is the connection to external equipment correct? (See pages 10, 11, 34 and 37.)
Has the input signal setup been performed correctly after connection? (See page 39.)
Is the correct input selected? (See pages 34, 35 and 37.)
Is the picture adjustment correct? (See pages 30 to 31.)
Is the antenna connected properly? (See page 9.)
Is “On” selected in “Audio Only”? (See page 23.)
Cautions regarding use in high and low temperature environments
• When the unit is used in a low temperature space (e.g. room, office), the picture may leave trails or appear slightly delayed.
This is not a malfunction, and the unit will recover when the temperature returns to normal.
• Do not leave the unit in a hot or cold location. Also, do not leave the unit in a location exposed to direct sunlight or near a
heater, as this may cause the cabinet to deform and the LCD panel to malfunction.
Storage temperature: f20°C to e60°C.
41
40G100H_en.indd
41
2009-12-17
14:16:19
Appendix
Reset
If complex adjustments are made and the settings
cannot be restored to normal, you can reset the
settings to the factory preset values.
1
Press MENU and the MENU screen displays.
2
Press c/d to select “Setup”.
3
Press a/b to select “Reset”, and then press
ENTER.
4
Press c/d to select “Yes”, and then press
ENTER.
• When “Reset” is completed, the backlight will turn
off and then on in a short period of time.
• The screen will be returned to its original state.
• “Execute Auto Installation” displays on the screen.
5
6
Press c/d to select “Yes” and then press
ENTER.
Press a/b to select the desired language
listed on the screen, and then press ENTER.
Press c/d to select “HOME” or “STORE”, and
then press ENTER.
Press a/b to select the desired sound system,
and then press ENTER.
You do not need to do anything during the auto
search.
Press MENU to exit.
NOTE
• If you execute “Reset”, all the settings such as Picture,
Audio, Programme and Language will be reset to the
factory preset values.
42
40G100H_en.indd
42
2009-12-17
14:16:20
Appendix
Specifications
Model
LC-40G100H
Item
LCD panel
40o (1020 mm) Advanced Super View & BLACK TFT LCD
Resolution
2,073,600 pixels (1920g1080)
Video Colour System
PAL/SECAM/NTSC 3.58/NTSC 4.43/PAL 60
TV Function
TV-Standard
PAL: B/G, D/K, I SECAM: B/G, D/K, K/K1 NTSC: M
Receiving
Channel
VHF/UHF
44.25-863.25 MHz
CATV
S1-S41ch (including Hyperband)
TV-Tuning System
Auto Preset 99 ch
STEREO/BILINGUAL
NICAM: B/G, I, D/K A2 stereo: B/G
Brightness
450cd/ m2
Backlight life
60,000 hours (at Backlight Standard position)
Viewing angles
H : 176º V : 176º
Audio amplifier
10Wg2
Speakers
(10 g 4.5 cm)g 2pcs
Terminals Rear
天线 (Antenna input)
UHF/VHF 75 q Din type
输入1 (INPUT1) (HDMI)
HDMI (HDMI input) (480P, 576P, 720P/50Hz, 720P/60Hz, 1080I/50Hz,
1080I/60Hz,1080P/50Hz, 1080P/60Hz, 1080P/24Hz), AUDIO in (common use
with 输入 7 (INPUT7)) (Ø 3.5 mm jack)
输入2 (INPUT2) (HDMI)
HDMI (HDMI input) (480P, 576P, 720P/50Hz, 720P/60Hz, 1080I/50Hz,
1080I/60Hz,1080P/50Hz, 1080P/60Hz, 1080P/24Hz)
输入3 (INPUT3)
VIDEO in, AUDIO in
输入4 (INPUT4)
S-VIDEO in, VIDEO in, AUDIO in
输入5 (INPUT5)
COMPONENT in (480I, 576I, 480P, 576P, 720P/50Hz, 720P/60Hz, 1080I/50Hz,
1080I/60Hz), AUDIO in
输入6 (INPUT6)
COMPONENT in (480I, 576I, 480P, 576P, 720P/50Hz, 720P/60Hz, 1080I/50Hz,
1080I/60Hz), AUDIO in
输入7 (INPUT7)
(PC input)
15 pin mini D-sub, AUDIO in (common use with 输入 1 (INPUT1)) (Ø 3.5 mm jack)
输出 (Audio output)
Audio output terminal
OSD language
English/Simplified Chinese/Traditional Chinese/Arabic/Thai
Power Requirement
AC 110-240 V, 50 Hz
Power Consumption
170 W (0.8 W Standby)
Weight
without stand
14.0 kg
with stand
17.0 kg
Operating Temperature
0°C - 40°C
• As a part of policy of continuous improvement, SHARP reserves the right to make design and specification changes for
product improvement without prior notice. The performance specification figures indicated are nominal values of production
units. There may be some deviations from these values in individual units.
43
40G100H_en.indd
43
2009-12-17
14:16:21
Appendix
Dimensional drawings
Unit: mm
526.2
987
116.7
96.5
400
500.4
626
689
887.8
63
325
300
161.1
300
44
40G100H_en.indd
44
2009-12-17
14:16:22
Appendix
Clearing the password
If you forget your password, set a new password using the following procedure.
1
Press MENU and the MENU screen displays.
2
Press c/d to select “Setup”.
3
Press a/b to select “Child Lock”, and then press ENTER.
4
The password input screen displays.
5
If you enter “3001” using 0 – 9, the “Child Lock” setting menu will be displayed.
6
Enter the 4-digit number as a password using 0 – 9. (See page 25.)
The new password is now set.
The Password is
.
NOTE
• As a precautionary measure, make a note of your password above, remove it from this manual, and keep it in a familiar place.
45
40G100H_en.indd
45
2009-12-17
14:16:23
Memo
46
40G100H_en.indd
46
2009-12-17
14:16:24
Memo
47
40G100H_en.indd
47
2009-12-17
14:16:25
Memo
48
40G100H_en.indd
48
2009-12-17
14:16:25
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement