Canister Vacuum with Motorized
Power Head
OWNER’S MANUAL
Model FM732H
120V., 60Hz., 12 Amps
FANTOM
94 Main Mill Street, Door 16
Plattsburgh, NY 12901
Tel.: 1-800-275-9251 www.fantom.com
IMPORTANT SAFETY INSTRUCTIONS
When using your canister vacuum, basic safety precautions should always be observed, including the following:
WARNING: To reduce the risk of fire, electrical shock, or injury:
1. Do not leave vacuum cleaner unattended when it is plugged in. Unplug from outlet when not in use.
2. To reduce the risk of electric shock – do not use outdoors or on wet surfaces. Do not handle plug or vacuum cleaner with wet hands.
3. Do not allow children to use as a toy.
Close attention is necessary when used by or near children.
4. Use only as described in this manual. Use only manufacturer’s recommended attachments.
5. Do not use with damaged cord or plug. Do not use vacuum cleaner if it has been dropped, damaged, left outdoors, or dropped into water. Return appliance to
FANTOM for examination, repair or adjustment.
6. Do not pull or carry by cord. Do not use cord as a handle, close a door on cord, or pull cord around sharp edges or corners. Do not run appliance over cord.
Keep cord away from heated surfaces.
7. Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord.
8. Keep hair, loose clothing, fingers, and all parts of body away from openings and moving parts.
9. Do not pick up hot coals, cigarette butts, matches or any hot, smoking, or burning objects.
10. Do not pick up hard or sharp objects such as glass, nails, screws, coins, etc.
11. Do not use without filters in place.
12. Turn off all controls before plugging or unplugging vacuum cleaner.
13. Use extra care when vacuuming on stairs.
14. Do not pick up flammable or combustible materials (lighter fluid, gasoline, kerosene, etc.) or use in the presence of explosive liquids or vapor.
15. Do not pick up toxic material (chlorine bleach, ammonia, drain cleaner, etc.).
16. Do not use in an enclosed space filled with vapors given off by oil based paints, paint thinner, moth proofing substances, flammable dust, or other explosive or toxic vapors.
17. Always unplug this appliance before connecting or disconnecting vacuum hose. Always hold the plug when rewinding the power cord. Do not allow plug to whip when rewinding.
18. Use only on dry, indoor surfaces.
19. Do not use for any purpose other than described in this user’s guide.
20. Use only extension cords UL or cULrated at 15 amperes. Extension cords rated for less amperage may overheat.
Care should be taken to arrange the cord so that the cord cannot be pulled or tripped over.
21. Do not put any objects into openings.
Do not use with any opening blocked.
Keep free of dust, lint, hair and anything else that may reduce air flow.
22. Store your appliance indoors in a cool, dry area.
23. Keep your work area well lit.
24. Do not immerse the vacuum in water or other liquids.
25. Keep end of hose, wands and other openings away from your face and body.
SAVE THESE INSTRUCTIONS
For Household Use Only
WARNING: To reduce the risk of electric shock, this appliance has a polarized plug (one blade is wider than the other). This plug will fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician to install the proper outlet. Do not modify the plug in any way.
1
Rev. 02/04A
Model
FM732H
ONE (1) YEAR LIMITED WARRANTY
FANTOM warrants this product to be free from defects in material and workmanship for a period of one (1) year from the date of the original purchase, when utilized for normal household use, subject to the following conditions, exclusions and exceptions.
If your appliance fails to operate properly while in use under normal household conditions within the warranty period, return the complete appliance and accessories, freight prepaid to:
FANTOM, 94 Main Mill Street, Door 16, Plattsburgh, N.Y. 12901
If the appliance is found by FANTOM to be defective in material or workmanship, FANTOM will repair or replace it free of charge. Proof of purchase date and
$ 19.95 to cover the cost of return shipping and handling must be included. *
Non-durable parts including, without limitation, filters, brushes and electrical parts which normally require replacement are specifically excluded from warranty.
The liability of FANTOM is limited solely to the cost of the repair or replacement of the unit at our option. This warranty does not cover normal wear of parts and does not apply to any unit that has been tampered with or used for commercial purposes. This limited warranty does not cover damage caused by misuse, abuse, negligent handling or damage due to faulty packaging or mishandling in transit. This warranty does not cover damage or defects caused by or resulting from damages from shipping or repairs, service or alterations to the product or any of its parts, which have been performed by a repair person not authorized by FANTOM.
This warranty is extended to the original purchaser of the unit and excludes all other legal and/or conventional warranties. The responsibility of FANTOM if any, is limited to the specific obligations expressly assumed by it under the terms of the limited warranty. In no event is FANTOM liable for incidental or consequential damages of any nature whatsoever. Some states do not permit the exclusion or limitation of incidental or consequential damages, so the above may not apply to you.
This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
*Important: Carefully pack item to avoid damage in shipping. Be sure to include proof of purchase date and to attach tag to item before packing with your name, complete address and phone number with a note giving purchase information, model number and what you believe is the problem with item. We recommend you insure the package (as damage in shipping is not covered by your warranty). Mark the outside of your package “ATTENTION CUSTOMER
SERVICE”. We are constantly striving to improve our products, therefore the specifications contained herein are subject to change without notice.
yyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyyy
OWNERSHIP REGISTRATION CARD
Please fill out and mail the product registration card within ten (10) days of purchase. The registration will enable us to contact you in the unlikely event of a product safety notification. By returning this card you acknowledge to have read and understood the instructions for use, and warnings set forth in the accompanying instructions.
RETURN TO: FANTOM, 94 Main Mill Street, Door 16, Plattsburgh, NY 12901
Appliance model
______________________________________________________________________
Date purchased Name of store
______________________________________________________________________
Owner’s name
______________________________________________________________________
Address City State Zip code
Printed in China
10
PROBLEM SOLVING
This appliance was inspected thoroughly and was in good operating condition when it was shipped from the factory. If a minor problem occurs, it usually can be solved quite easily when the cause is found. Therefore, this checklist is provided for your convenience.
POSSIBLE
Cleaner Won’t Run
1. Not firmly plugged in.
2. No electricity in wall outlet.
3. On/Off switch not turned on.
5. Blown fuse/tripped breaker.
1. Plug in firmly, push on/off switch to on.
2. Check fuse or breaker.
3. Push on/off switch to on
4. Reset thermal protector.
5. Reset circuit breaker or replace fuse.
1. Full or clogged dust cup.
2. Clogged nozzle or dust cup port.
Cleaner Won't Pick
Up
Air Flow Restricted
With Attachment
Use Sound Changes
4. Hole in hose.
5. Hose not inserted fully.
6. Motor protection system activated. filters.
8. HEPA filter needs cleaning or replacing.
9. Debris screen needs cleaning.
1. Attachment use restricts airflow.
2. New carpet trimmings clogging air passage.
1. Clean dust cup. obstruction.
3. Remove hose.
5. Push hose in securely.
6. Reset thermal protector.
7. Clean / change filters.
8. Clean or replace HEPA filter.
9. Clean debris screen.
1. Check attachment. obstruction.
ORDERING REPLACEMENT DUST CUP FILTERS
TO ORDER REPLACEMENT FILTERS OR FOR TECHNICAL
SUPPORT
HEPA Filter Item # XF732H for Model FM732H
Call: 1 (800) 275-9251
Monday to Friday 8:30 A.M. - 5:00 P.M. Eastern Standard Time
Please Note:
The HEPA Dust Cup Filter may be washed. We recommend that this be done once a month or when suction appears reduced. To wash your HEPA Dust Cup Filter, hold filter cartridge by frame flange and rinse under a tap until all observable dirt has been removed. Some discoloration of the HEPA filter material may occur, this is normal and will not affect the filter's performance. When finished, shake off excess water. Do NOT wash in dishwasher. It is important that when you wash the HEPA dust cup filter, you allow it to dry COMPLETELY before using it again. We recommend 24 hours to air dry. DO NOT DRY IN DRYER. We recommend replacing the HEPA filter every three
(3) to six (6) months, depending on the amount of use to ensure peak performance of your vacuum.
IMPORTANT: The Pre-Motor filter and Post Motor filter should be replaced every 6 months or sooner if required. It is important that when you wash the HEPA dust cup filter, pre-motor filter or the exhaust filter you allow them to dry COMPLETELY before using again. We recommend 24 hours to air dry. DO NOT DRY IN DRYER.
All filters should be checked regularly for signs of damage, preferable after each cleaning task. The filters must be replaced immediately if they become damaged.
Always disconnect the vacuum from the electrical outlet when checking the filters.
9
GETTING TO KNOW YOUR CANISTER VACUUM
1.
On/Off Button
2.
Cord Rewind Button
3.
Carrying Handle
4.
Dust Cup (Container)
5.
Dust Cup Handle
6.
Dust Cup Full Indicator
7.
Hose Connector Inlet
8.
Hose Connecting Power Cord
9.
Hose Connecting Power Cord
10. Hose Connector
11. Flexible Hose
* Illustrations may differ from actual product.
12. Receptacle For Motorized Brush
Power Cord
13. Motorized Brush Power Cord
14. Telescopic Tube
15. Motorized Brush
16. Motorized Brush On/Off Button
17. Head Light
18. Floor-to-carpet Brush
19. Upholstery Brush
20. Crevice Tool
21. Furniture Guard
Technical Specifications
Main Unit: Voltage:
Power:
120V., 60Hz.
10.3 Amps
With Motorized Power Head: Voltage: 120V., 60 Hz.
Power: 12 Amps
2
PRECAUTIONARY MEASURES
Important:
If the suction opening of the unit, the hose or the chrome telescopic tube are BLOCKED, switch off the vacuum cleaner and remove the blocking substance before you start the unit again.
1.
Do not operate the vacuum cleaner too close to heaters or radiators.
6.
Do not pick up anything that is burning or smoking such as cigarettes, matches or hot ashes.
2.
Before inserting the power plug into the wall outlet, make sure that your hands are dry.
7.
Do not obstruct the air inlet or outlet vents.
8.
Do not use vacuum cleaner on wet surfaces.
3.
Before you start vacuuming, make sure to remove large or sharp objects that might damage the dust cup.
9.
Do not use without all filters in place.
Note:
This vacuum cleaner is equipped with a plug and power cord that retract automatically. If the cord or plug get damaged, it must be replaced by a qualified technician.
Warning:
Hold the plug when rewinding the cord. Do not allow the cord to whip when rewinding.
4.
Do not run the vacuum cleaner over the power cord.
5.
When pulling out the power plug from the wall outlet, pull the plug not the power cord.
OPERATING INSTRUCTIONS
Changing & Cleaning the Post
Motor Filter
The post motor filter is a washable filter but should be replaced every six (6) months depending on usage. Never operate the vacuum without ALL the filters in place.
• Push the Power On/Off button to the
"Off" position and disconnect the power cord from the wall outlet.
• The post motor filter is located on the rear of the vacuum. Remove the filter cover.
• Remove the filter grill and take out the filter.
• Rinse in lukewarm water, let air dry completely. Do not use a washing machine to rinse the filter. Do not use a hair dryer to dry it. Air dry only for 24 hours.
• When filter is completely dry, replace post motor filter back into the filter grill and replace back into the unit.
Please Note: The HEPA Dust Cup
Filter is washable. It should, however, be replaced every six (6) months to ensure peak performance of your vacuum.
The Post Motor Filter and Pre-Motor
Filter are washable. They should however be replaced every six (6) months to ensure peak performance of your vacuum.
Important: Make sure that ALL filters are completely dry before re-installing back in the hand vacuum.
Important: All filters should be checked regularly for signs of damage, preferably after each cleaning task. The filters must be replaced immediately if they become damaged. Always disconnect the vacuum from the electrical outlet when checking the filters.
3 8
OPERATING INSTRUCTIONS
7. Vigorously “TapClean” the HEPA Dust Cup
Filter on a hard surface until no more dust is observed falling out from between the pleats of the filter. See illustration at right.
PLEASE NOTE: The white pleated filter material in the HEPA Dust Cup
Filter will discolor over time -This is
NORMAL and will NOT affect the performance of the filter. If the HEPA
Dust Cup Filter
Fig. A is properly
"TapCleaned” after each use and suction does not return to 100%, then we suggest that the HEPA filter
Wash once a month or when suction appears reduced be “TapCleaned” vigorously until
Warning: Allow 24 hours for drying before replacing in unit.
no more dust can be removed, then rinsed under the faucet and allowed to air dry for 24 hours before refitting into the vacuum.
(Fig. A) This should be done once a month or when suction appears to
be reduced.
Important
: The suction hole must be open, free of any obstructions at all times. Otherwise, the motor will overheat and could become damaged.
8. Reassemble the debris screen back onto the HEPA filter cartridge.
9. To replace the HEPA filter back into the dust cup container, hold the filter by the stem and insert it up into the dust cup container making sure that the top rim of the filter fits onto the top of the dust cup container and twist it clockwise to lock in place.
Ensure that the filter assembly is completely seated inside the dust cup (container).
Important:
Do NOT use the HEPA filter cartridge without the debris screen in place.
10. Re-install dust cup into the vacuum and re-attach hose.
Changing & Cleaning the
Pre-Motor Filter
The pre-motor filter is located underneath the dust cup container.
This is a rinseable filter but should be replaced every six (6) months. Never operate the vacuum without ALL the filters in place.
• Push the Power On/Off button to the
"Off" position and disconnect the power cord from the wall outlet.
• Remove the dust cup container.
• Remove the pre-motor filter and rinse in lukewarm water, let dry completely.
Do not use a hair dryer to dry it. Air dry only.
• When filter is completely dry, replace pre-motor filter back into the unit and replace the dust cup container.
7
Assembling Your Vacuum Cleaner
Note:
Always remove the power plug from the wall outlet before assembling or removing accessories.
1. Attaching the Flexible Hose into the Vacuum
Connect the flexible hose into the air intake duct. Push in until you hear a
“click”, indicating it is in its locked position.
To remove the flexible hose first remove the power nozzle power cord from the receptacle for the power nozzle power cord, then depress locking button and remove hose.
Connect the hose connecting power cord from the flexible hose to the power cord receptacle that is on the unit just below the air intake duct.
Air intake duct
OPERATING INSTRUCTIONS
4. Fitting the Floor to Carpet
Brush to the Telescopic Tube
Push the telescopic tube into the floor brush as show in the illustration below.
Telescopic
Tube
Floor to Carpet
Nozzle
Using Power Nozzle
1.
Connecting the power nozzle with the telescopic tube:
A) Depress the button on the telescopic tube and insert it into the slot on the power nozzle elbow.
B) Push the telescopic tube down until you hear a "click".
(see illustration below).
Power cord receptacle
2. Fitting the Telescopic Tube to the Curved Wand / Hose
Extension
Push the telescopic tube into the curved wand / hose extension, as shown in the illustration below.
Make sure that the telescopic tube locks in place.
Telescopic
Tube
Power
Nozzle
3. Extending the Telescopic Tube
Push forward on the plastic button and pull the inner tube outward.
Plastic
Button
2.
Insert the motorized brush power cord plug into the power socket on the flexible hose. To start motorized brush press the
On/Off button that is located on the motorized brush.
4
Using your Vacuum
Note:
Once all attachments are in place, unwind a sufficient length of cable and insert the plug into the wall outlet. A yellow mark on the power cord shows the ideal cable length. Don't pull the power cord beyond the red mark.
Cord Rewind
Button
OPERATING INSTRUCTIONS
Crevice Tool and Dusting Brush
1.
Crevice Tool with Brush
For radiators, crevices, corners, baseboards and between cushions.
2.
Upholstery Brush
The dusting brush is used for the furniture
3. To rewind the power cord, press the cord rewind button with one hand and hold the plug of the power cord with the other hand to ensure that it does not whip causing damage or injury.
Motor Thermostat
Important:
This vacuum cleaner is equipped with a motor protective thermostat. If for some reason your vacuum overheats, the thermostat will automatically turn the unit off. Should this occur, unplug the vacuum from the wall outlet and turn off the switch. Empty the dust cup, "TapClean" the dust cup filter and check for blockages in hose and suction inlet. Allow the unit to cool for a minimum of 45 minimum prior to restarting the unit. To restart, re-plug the vacuum into the wall socket and turn the switch back on
1. Insert the power plug into the wall outlet.
2. Press the Power On/Off button located on the unit to turn the vacuum cleaner "On".
Power On/Off
Button
5
OPERATING INSTRUCTIONS
Removing & Cleaning the
Rinseable "TapClean" HEPA
Dust Cup Filter
Warning:
Always unplug the unit from electrical outlet before removing the Dust Cup (container).
1. Push the Power On/Off button to
"Off" and disconnect the power cord from the wall outlet.
2. Lift the dust cup handle and lift the dust cup container out.
3. Hold dust cup container over a waste basket (garbage can), push the dust cup release button to open the dust cup. Dispose of the dust inside. (See illustration below.)
Note: If dust is tightly packed and difficult to remove, tap the side of the dust cup lightly against the side of the waste basket (garbage can).
5. After you have removed the
Rinseable "TapClean" HEPA dust cup filter from the dust cup, separate the debris screen from the HEPA filter cartridge by holding the top rim of the filter and twisting the debris screen counterclockwise to unlock the debris screen from the filter. Then lift the debris screen to remove.
6. Rinse the debris screen under the faucet with lukewarm water until clean. Allow to air dry for 24 hours.
Do NOT wash in dishwasher.
Warning
: After each Use - Always remove the Rinseable "TapClean"
HEPA Filter from the Dust Cup, then vigorously “TapClean” HEPA Filter until no more dust can be removed.
Important:
When "TapCleaning" the
HEPA filter, hold the HEPA filter from the stem and tap ONLY the top rim against the side of the waste container. NEVER tap directly on the pleated folds of the
HEPA filter.
Stem
4. After you have emptied the dust container, hold the
HEPA filter from the stem and twist it counter clockwise to release it from the dust cup container.
Press
Open
6
Top Rim
IMPORTANT, Please Note: The
Rinseable “TapClean” HEPA Dust Cup
Filter will stop most of the tiniest dust particles from re-entering the air you breathe. In fact it stops 99.97% of all particles as small as 0.3 microns - many times smaller than a human hair!!!
Because of this incredible filtration performance, the HEPA Dust Cup Filter will quickly accumulate dirt inside the white filter folds, many fine dust particles that are difficult to see but which will eventually block or reduce your suction power - if not cleaned properly. Clean the
HEPA Filter as described in this section, then reconnect unit and proceed with vacuuming.)
