cycle computer
CPP-LUICTC 3
CP-LUICIO 3
|
CYCLE COMPUTER
CP-W1009
Manual
Before using the computer, please
through this manual thoroughly.
* Please keep this
manual for future reference.
How to install the unit on your bicycle
OBracket
@Speed sensor
© Speed sensor rubber pedestal pad
OSpeed sensor pedestal pad
© Super magnet
ONylon ties (x8)
@Bracket rubber pedestal pad
o
№
° ©
хо
Ÿ
A
N
VO
© o <>
(fig 3
@The speed sensor and the magnet installation
Speed sensor rubber
pedestal pad €) installation
bbe
1 Insert speed sensor @ into speed
sensor pedestal pad O as (fig 1)
shows. Install speed sensor rubber
pedestal pad © between front fork
> sensor @ to the
front fork by
fastening it with the
nylon ties @(fig 2)
Install the speed
Leo Fasten the speed sensor @ loosely to adjust the position and angle.
When it is at the desired position, secure it by tightening the nylon ties.
The distance between the speed sensor @
and the computer main unit must not exceed
70cm. (fig 3)
2 Install the magnet @ on the front spoke so
that the face of the magnet is directed
towards the sensor surface.
Make sure that the path of the rotating
magnet@ passes the line of the speed
(fig 4) sensor® (©) mark. {fig 4) (Super magnet
© is compatible with both flat spokes and
the round spokes)
3 Adjust the distance between the super magnet
O and the speed sensor @ until that it does
not exceed 5mm. If the distance is farther
(fig 5)
4 Once the position has been decided, install the
speed sensor @ and the super magnet O
securely with the nylon ties @.
and speed sensor @ as (fig 1) shows. @The bracket installation
The bracket @ can be installed on the handlebar or
handle stem.
Set the bracket on the bracket pedestal @ (fig 6) .
Fasten the bracket © loosely to adjust the position
and angle. When it is at the desired position, install
it securely with the nylon ties @.
(fig 6)
2.Slide the computer
N onto the bracket
Click!
© (© until it clicks. 7)
с 3.When removing the
ZZ) computer, press the
release lever and
— < Hh slide it off.
(fig 7)
than 5mm, adjust the speed sensor @ angle.
1. Rotate the front wheel gently
to check that the speed is
displayed on the computer.
. After checking the speed
display on the computer,
adjust and cut the surplus
N
{fig 8) nylon ties@.
3. If the speed is not displayed
on the computer, re-adjust
the installation points.
Warning
Caution benzene, or alcohol.
- — ER EE Em EE EE,
Adjust digit
Press the MODE button
(to select
Install the magnet, sensor, and bracket securely. Check these periodically.
A Do not concentrate on the computer while riding.
Dispose of used batteries according to local regulations.
Avoid having the computer in direct sunlight for unnecessary or extended
/ | \ periods.
When cleaning the computer, bracket and sensor, do not use thinners,
Change screen
Press the MODE button D
to change screen
Move to
next setting
digit
Press and hold the MODE
button €) 2 secs
Reset data
Press and hold
the MODE button (1) 3 secs
(DST, CAL, RTM, AVG, MAX)
For the detail please refer
RESET DATA on the back page
Turn to
next function
Press the SET button O) to
turn to next function
Rekey data
Press the SET button ®
to enter setting mode
For the detail please refer E SET button
and operation on the back page
Quit
setting mode
Press and hold
the SET button®2 secs
Y
oe
Press and hold the MODE
Press the MODE button © button ©) for 2 seconds Press the SET button ©
to increase the value. to move to the next digit. to store the digit.
«>:
>
a
0»
(>
(>
E
VA
CLEAR THE COMPUTER
OCLEAR THE COMPUTER
1 A battery is already included in the main unit when purchased. Hold down the MODE
button 0) and SET button G)simultaneously for more than 3 seconds to initiate the
computer and clear all data.
IMPORTANT: be sure to go through the steps of initiating the computer before use,
otherwise the computer may run with errors.
2 The LCD segments will be tested automatically after the unit is initiated.
3 Press the MODE button () to stop the LCD testing, then the flickering "Km/h".
BJ UNIT SELECTION
| Clear the computer |
© ©
o
Press the MODE button) to choose
“KM/H” or “M/H”.
Then press the SET button © to store
the selection.
Fig. a 7
r st
b
77777 TT
2nd
2 WHEEL CIRCUMFERENCE ! You can set two wheel circumferences.
Precise Measurement (Fig. a)
1 Roll the wheel until the valve stem is at its
lowest point, closest to the ground, and mark
this point on the ground.
2 Get on the bicycle and have a helper push
you until the valve stem returns to its lowest
point. Mark the second point on the ground.
3 Measure the distance between the marks by
milmeter. Enter this value (mm) to set the
wheel circumference. You can get a suitable
circumference value from the table. (Fig b)
4 Press the MODE button (Dto store the data.
5 Start setting the digit from thousandth. Press
the MODE button (Dto store the thousandth
digit, and move to hundredth and so on.
6 Once the wheel circumference has been
completed, press the SET button®to store
the data.
ЮМоуе to
ODO setting
and resetting
f=
END setting
1
Press the MODE button O) and select
12HR or 24 HR.
2
When selecting 12 HR, select morning (A)
or afternoon (P) .
3
Press the MODE button ©) to store the
selection.
4
@A new user who does NOT need
to enter ODO
Press the SET button ® for two seconds,
and initial setting will be completed.
@A user who NEEDS to enter ODO
Press the SET button 6), and ODO
Setting and resetting mode appears on
the screen.
000000—999999
РТ ODO Setting : total odometer setting
Enter the odometers as shown in the
illustration to the left.
Once all odometer data have been entered,
press the SET button © for two seconds,
and ...
initial setting will be completed.
">
