- No category
advertisement
1 2
GETTING STARTED
3 4
Power
Button
OPERATING MODES
Heading Follow Mode - 1 Click
CHARGING BATTERIES
Connect charger to any standard USB outlet or phone charger using the included Micro USB cable. Batteries take approximately 2 to 3 hours to fully charge. Shorter charge times can be achieved using higher mA rating AC/DC adapter.
Red Light = Charging
Green Light = Finished
Input: DC 5V / 800mA
Output: 4.2V / 400mA x2
3 Axis GoPro
Stabilizer
Compatible With:
Remove battery end cap and install the extension tube.
5
Insert both charged
18650 LiPo Batteries and screw on end cap.
Depress thumbstick for 2 seconds to power on motors
Mount Camera by screwing thumbscrews to mounting bracket.
6
Initialize gimbal first by setting on flat non-moving surface. Press power button and wait 3-4 seconds for calibration lights to stop.
Pitch & Roll axis are locked.
Pan axis rotates smoothly with turn of wrist.
Use thumbstick up and down to control tilt of camera.
Heading Lock Mode - 1 Click
G I M B A L S . C O M
QUICKSTART GUIDE
INCLUDED IN THIS BOX
EVO GP-PRO Gimbal Body
GoPro Mounting Bracket
Thumb Screw M2 5x20mm
Thumb Screw M2 5x10mm
18650 LiPo Battery
18650 LiPo Battery Charger
USB Charge Cable
Battery Extension Tube
Quality Control Certificate
QuickStart Guide
Warranty Registration Card
Please check that all items are included, if you are missing any items or components please contact your dealer immediately!
x2 x2 x1 x1 x1 x1 x1 x1 x1 x2 x2
This device has been calibrated and tested from the manufacturer. Any dissasembly or modification to components will void warranty. For the latest version of user manuals and tutorial videos please visit our official website: www. EVOGimbals.com
IMPORTANT!
To motor side ALWAYS INSTALL
GOPRO BEFORE
APPLYING POWER!
Failure to do so can damage the unit!
EVO Gimbals come with a 1 Year Parts & Labor warranty. Be sure to register your warranty by either mailing in the warranty registration card or register online at EVOGimbals.com/support
For the latest user manuals, tutorial videos, firmware and calibration instructions please visit our official wepage at EVOGimbals.com
To power on motors, depress thumbstick for 2 seconds.
Single click the thumstick to switch between “Heading
Follow Mode” and “Lock Mode”. Double click to enter
“Heading and Pitch Follow Mode”. To power OFF motors
(standby mode) simply depress thumbstick for 2 seconds.
USB Port
3.5mm AV
Ouptut
18650 LiPo
Battery X2
Extension
Tube
Battery Cap with1/4-20
Thread Screw
Indicator Light
Power Button
Thumbstick
GoPro
Mounting
Bracket
Serial Number
Printed on Handle
Adjust the camera tilt angle by pushing up or down on the thumbstick. Camera tilt can only be adjusted in
Heading Follow Mode or Lock Mode. Camera horizon angle can be adjusted when in “Heading and Pitch
Followmode”.
Pitch, Roll and Pan axis are locked.
Use thumbstick up and down to control tilt of camera.
Use thumbstick left and right to manually pan camera left/right
Heading & Pitch Follow Mode
-
2 Clicks
EVO GP-PRO OVERVIEW
Thumbscrews
Note: Be sure to securely mount camera tight to mounting tray. Camera should be tight to tray as close to motor as possible.
GoPro Charging & A/V Output Port Configuration
Charging
Port
There are 2 GoPro accessory cables included. The 3 pin cable is for charging, and the 4 pin cable is for both charging and activation of
3.5mm A/V output port so you can connect an external monitor.
Choose the appropirate cable for your application and please note that once the AV cable is plugged into the monitor that your LCD monitor on your GoPro will turn off automatically.
Note: A/V cables are sold separatley from your dealer.
Roll axis is locked. Pan and Pitch axis smoothly follow handle.
Use thumbstick left and right to adjust the pan angle.
Single click thumbstick to exit into previous mode.
Note that upon exiting this mode the camera tilt angle and horizon angle will remain locked in last position.
Inverted Mode
To use gimbal inverted enter into
“Heading and Pitch Follow Mode” first. Rotate gimbal 180 degrees front ward until camera is upside down. You can now enter into the other modes with the gimbal inverted.
To return the gimbal upright enter into Heading and Pitch Follow
Mode (2 clicks) and rotate gimbal
180 degrees backward until camera is upright. You can now enter into other modes.
You can optionally mount the camera upside down so you do not have to correct the video in post production.
Filming in upside down mode is typically used for low level shooting.
For additional information and video tutorials on switching between modes and their intended uses please go to
EVOGimbals.com
ALWAYS use geniune
ICR 18650 OEM EVO batteries!
Our batteries have built-in discharge and overcharge protection for long life and safety!
Additional batteries can be purchased from your dealer or EVOGimbals.com
Power
Indicator
Monitor Battery Power:
4 Flashes = 75-100%
3 Flashes = 50-75%
2 Flashes = 25-50%
Quick Flashes = 0-25%
PERFORMANCE & SPECIFICATIONS
Dimensions (mm) MAX CAMERA DIMENSIONS
Height:
Width:
42.7mm
31mm
Stabilization Accuracy:
Follow Accuracy:
Pan Axis Range:
Tilt Axis Range:
Roll Axis Range:
Tilt Axis Control Speed:
Pan Axis Control Speed:
Motor Type:
Working Current Static Current:
Dynamic Current:
Max Motor Current:
Sensors:
Batteries:
±0.01°
±0.2°
-135° to +135°
-90° to +180° (Inverted)
-45° to +45°
Min 1°/s Max 50°/s
Min 1°/s Max 80°/s
3x Triple Wound HT Brushless
6.8 mA (at 6.8 VDC)
120mA (at 8.4 VDC)
2A maximum (at 12.6 VDC)
IMU module, HD Encoders
ICR 18650, 2000mAh x2
(included)
Operating
Temperature: -5 to 122°F / -15 to 50°C
Weight: 0.75 lbs / 310g (unloaded)
Supported Cameras: GoPro Hero 3/Hero 3+/Hero 4
XE weight)
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project