Instruction Manual
Smiling Mickey Edge Stroller
IMPORTANT PLEASE READ THESE INSTRUCTIONS
CAREFULLY BEFORE USING THIS PRODUCT
KEEP FOR FUTURE REFERENCE
2 Safety Warnings
Thank you for choosing Obaby. To ensure that your stroller is used in accordance with these instructions, please read them fully.
This stroller conforms to EN 1888:2003 and is guaranteed for 12 months from the date of purchase against manufacturing defects. If, however you have any problems, please contact your Obaby retailer from whom you purchased your product, who will take appropriate action.
Your child’s safety may be affected if you do not follow these instructions.
WARNING: A child’s safety is your responsibility
WARNING: Ensure that all locking devices are engaged before use
WARNING: Children should be harnessed in at all times
WARNING: Always use the crotch strap in combination with the waist belt
WARNING: Any load attached to the handles affects the stability of the pram / pushchair
WARNING: This product is not suitable for running or skating
WARNING: It may be dangerous to leave your child unattended
WARNING: The child should be clear of moving parts while making adjustments or opening or folding the stroller. Risk of serious injury
(entrapment, laceration or amputation) exists
• A basket is provided for the carriage of other items up to a maximum permissible weight of 3 kg. Where a hood parent pocket is provided, an additional 1kg maximum permissible weight can be used within this
• This stroller is intended to carry one child from birth and up to a maximum weight of 15kg
ROUTINE CARE & MAINTENANCE
- This stroller requires regular maintenance by the user
- It may be unsafe to use replacement parts or accessories e.g. child seats, bag hooks, rain covers, etc, other than those approved by the manufacturer or distributor.
- For cleaning, use only a mild detergent and warm water
- DO NOT USE BLEACH
- DO NOT USE any abrasive substances
- From time to time, check your stroller for loose screws, worn parts, torn material or stitching. Replace or adjust the parts as needed.
Due to constant updating and improvements, some components may occasionally differ slightly from the images shown in these instructions. We reserve the rights to change the specifications of any products without prior notice.
If you need any assistance please contact your Obaby retailer from whom you purchased your product, who will take appropriate action.
www.obaby.co.uk
Hood
Harness pads
Harness
Calf rest
Front swivel wheel levers
Parent window
Secondary release lock
Ventilation flap
Brake lever
Getting to know your Stroller www.obaby.co.uk
Bumper
Storage clip
Shopping basket
Primary release lock
Backrest release toggle
3
4 Unfolding your Stroller Folding your Stroller 5
Lift
Press
Lift fig. 1 fig. 2 fig. 3 fig. 7
Lower fig. 8 fig. 9
“Click” fig. 4 fig. 5 fig. 6
To open your stroller release the storage clip on the side of the stroller (fig.1 & 2).
Lift the handles up, away from the wheels (fig.3).
Ensure the frame clicks into place on both sides of the stroller (fig.4-6).
WARNING: Ensure that all locking devices are engaged before use fig. 10 fig. 11 fig. 12
Before attempting to fold your stroller
- The front wheel should be locked in place
- The basket and seat unit should be empty
- The hood should be folded
- The seat should be fully upright
To fold the stroller, release the primary lock by pressing the red button on the right handle (fig.8), while keeping this depressed, release the secondary lock by lifting the catches on each handle (fig.9).
Push the handles forward slightly then lower the handles towards the wheels (fig.10) until completely folded (fig.11). Ensure the storage clip has engaged (fig.12).
www.obaby.co.uk
www.obaby.co.uk
6 Fitting and Removing the Front Wheel
“Click”
Press
Applying the Brakes 7 fig. 13 fig. 14 fig. 15
To fit the front wheel, push the wheel onto the front leg (fig.13) until it clicks into place
(fig.14).
To remove the front wheel press the buttons either side of the leg beneath the wheel and slide the wheel away (fig.15).
Using the Front Swivel Wheel
Lock Release fig. 16 fig. 17 fig. 18
To lock the swivel wheel, first ensure the front wheel is facing forward inline with the chassis, then push the lever down (fig.16).
To put the wheels in swivel mode, lift the lever up on the front of the wheel (fig.17 & 18).
www.obaby.co.uk
Lock Release fig. 19 fig. 20 fig. 21
To lock the brakes fully, push down on the brake lever using your foot (fig.19 & 20).
To release the brakes, lift the brake lever using your foot (fig.21).
Apply the brake before putting your child into the pushchair.
Apply the brake when the pushchair is stationary.
Adjusting the Backrest
2. Pull
1. Press
Lift fig. 22 fig. 23 fig. 24
To recline the backrest, press the levers on the sides of the backrest release toggle, and slide the toggle down the straps to the desired height (fig.22). Lower the seat to rest on the toggle (fig.23).
To put upright, grip the top and bottom of the toggle with one hand and the strap with the other hand, and slide the toggle up the straps to the desired height (fig. 24).
www.obaby.co.uk
8 Fitting and Removing the Bumper Using the Harness 9
Clasp
Shoulder
Strap
Waist
Strap fig. 31
Crotch
Strap fig. 32
Press Press fig. 24 fig. 25 fig. 26
To remove the bumper, press the buttons underneath each side of the bumper (fig.24) and pull the bumper away from the chassis (fig.25).
To fit the bumper, simply push the stems on either side of the bumper into the receivers on the chassis (fig.25 & 26).
Adjusting the Hood fig. 30 fig. 27 fig. 28 fig. 29
To adjust the hood, simply move the peak to the desired position, as shown.
www.obaby.co.uk
fig. 33 fig. 34 fig. 35
To fasten the harness, insert both fasteners on the waist strap into the clasp on the crotch strap (fig.30 & 31).
To release the harness, press the buttons on either side of the clasp and remove the waist strap fastners (fig.32).
Adjust the harness length using the buckles on each strap (fig.33) and slide the waist strap fastner along the strap (fig.34).
‘D’ Ring
The ‘D’ rings are provided for fitting a separate harness complying with BS 6684 (fig.35).
WARNING: Always use the crotch strap in combination with the waist belt www.obaby.co.uk
10 Using the Calf Rest
Pull fig. 36 fig. 37
The calf rest pulls out from underneath the seat.
fig. 38 fig. 41 fig. 42
Fitting the Footmuff fig. 43
11
Parent Window and Ventilation fig. 39 fig. 40
To use the parent window lift the flap on the hood and roll up, secure in place with the toggle (fig.39).
For extra ventilation unzip the flap at the back of the stroller using the two zips, roll up and secure in place with the toggle (fig.40).
www.obaby.co.uk
fig. 44 fig. 45 fig. 46
Unthread the harness from the buckles on the chest strap and remove the harness pads, then pass all the straps through the appropriate holes on the footmuff (fig.41).
Replace the harness pads and re-thread the harness as shown (fig.42-44).
Fold the flap at the front of the footmuff over the bumper and secure each side with the toggles (fig.45 & 46).
www.obaby.co.uk
12 Fitting the Raincover fig. 47 fig. 48 fig. 49
Drape the raincover over the stroller ensuring the loops are around the handles (fig.47).
Secure using the velcro (fig.48).
WARNING: When using the raincover, regularly check your child has adequate ventilation and is not overheating.
Unless it is raining, the raincover should be removed.
www.obaby.co.uk
www.obaby.co.uk
13
©Disney
