ERI603COM - Free-Instruction

ERI603COM - Free-Instruction
ERI603COM
18V COMBI DRILL
ERI603COM
Original Instructions
(Version 1.0)
Congratulations on your purchase of a quality power tool from Erbauer (UK) Ltd. This
product should give you reliable service but for your peace of mind this
power tool does carry a 2 year guarantee, the terms of which are detailed below.
If this product develops a fault within the guarantee period contact your retailer.
Please retain this handbook in case you need to refer to safety, care or guarantee
information in the future.
GUARANTEE
This
product carries a 2 years guarantee. If your product develops a fault within this
period, you should in the first instance contact the retailer where the item was purchased.
This guarantee specifically excludes losses caused due to:
- Fair wear and tear
- Misuse or abuse
- Lack of routine maintenance
- Failure of consumable items (such as batteries)
- Accidental damage
- Cosmetic damage
- Failure to follow manufacturer’s guidelines
- Loss of use of the goods
This guarantee does not affect your statutory rights. This guarantee is only valid in the UK.
For further technical advice, spare parts or repair service (outside of guarantee) please contact
the customer helpline number on 0345 607 6380.
18V COMBI DRILL
ERI603COM
General Power Tool Safety Warnings
WARNING! Read all safety warnings and all instructions. Failure to follow the
warnings and instructions may result in electric shock, fire and/or serious injury.
Save all warnings and instructions for future reference.
The term “power tool” in the warnings refers to your mains-operated (corded) power tool or
battery-operated (cordless) power tool.
1)
Work area safety
a) Keep work area clean and well lit. Cluttered or dark areas invite accidents.
b) Do not operate power tools in explosive atmospheres, such as in the presence
of flammable liquids, gases or dust. Power tools create sparks which may ignite the
dust or fumes.
c) Keep children and bystanders away while operating a power tool. Distractions
can cause you to lose control.
2)
Electrical safety
a) Power tool plugs must match the outlet. Never modify the plug in any way. Do
not use any adapter plugs with earthed (grounded) power tools. Unmodified plugs
and matching outlets will reduce risk of electric shock.
b) Avoid body contact with earthed or grounded surfaces, such as pipes,
radiators, ranges and refrigerators. There is an increased risk of electric shock if your
body is earthed or grounded.
c) Do not expose power tools to rain or wet conditions. Water entering a power tool
will increase the risk of electric shock.
d) Do not abuse the cord. Never use the cord for carrying, pulling or unplugging
the power tool. Keep cord away from heat, oil, sharp edges or moving parts.
Damaged or entangled cords increase the risk of electric shock.
e) When operating a power tool outdoors, use an extension cord suitable for
outdoor use. Use of a cord suitable for outdoor use reduces the risk of electric shock.
f) If operating a power tool in a damp location is unavoidable, use a residual
current device (RCD) protected supply. Use of an RCD reduces the risk of electric
shock.
3)
Personal safety
a) Stay alert, watch what you are doing and use common sense when operating
a power tool. Do not use a power tool while you are tired or under the influence
of drugs, alcohol or medication. A moment of inattention while operating power tools
may result in serious personal injury.
b) Use personal protective equipment. Always wear eye protection. Protective
equipment such as dust mask, non-skid safety shoes, hard hat, or hearing protection
used for appropriate conditions will reduce personal injuries.
c) Prevent unintentional starting. Ensure the switch is in the off-position before
connecting to power source and/or battery pack, picking up or carrying the tool.
Carrying power tools with your finger on the switch or energising power tools that have
the switch on invites accidents.
d) Remove any adjusting key or wrench before turning the power tool on. A
wrench or a key left attached to a rotating part of the power tool may result in personal
injury.
e) Do not overreach. Keep proper footing and balance at all times. This enables
better control of the power tool in unexpected situations.
f) Dress properly. Do not wear loose clothing or jewellery. Keep your hair,
clothing and gloves away from moving parts. Loose clothes, jewellery or long hair
can be caught in moving parts.
g) If devices are provided for the connection of dust extraction and collection
facilities, ensure these are connected and properly used. Use of dust collection can
reduce dust-related hazards.
4)
Power tool use and care
a) Do not force the power tool. Use the correct power tool for your application. The
correct power tool will do the job better and safer at the rate for which it was designed.
b) Do not use the power tool if the switch does not turn it on and off. Any power
tool that cannot be controlled with the switch is dangerous and must be repaired.
c) Disconnect the plug from the power source and/or the battery pack from the
power tool before making any adjustments, changing accessories, or storing
power tools. Such preventive safety measures reduce the risk of starting the power tool
accidentally.
d) Store idle power tools out of the reach of children and do not allow persons
unfamiliar with the power tool or these instructions to operate the power tool.
Power tools are dangerous in the hands of untrained users.
e) Maintain power tools. Check for misalignment or binding of moving parts,
breakage of parts and any other condition that may affect the power tool’s
operation. If damaged, have the power tool repaired before use. Many accidents
are caused by poorly maintained power tools.
f) Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp
cutting edges are less likely to bind and are easier to control.
g) Use the power tool, accessories and tool bits etc. in accordance with these
instructions, taking into account the working conditions and the work to be
performed. Use of the power tool for operations different from those intended could
result in a hazardous situation.
5)
Battery tool use and care
a) Recharge only with the charger specified by the manufacturer. A charger that
is suitable for one type of battery pack may create a risk of fire when used with another
battery pack.
b) Use power tools only with specifically designated battery packs. Use of any
other battery packs may create a risk of injury and fire.
c) When battery pack is not in use, keep it away from other metal objects, like
paper clips, coins, keys, nails, screws or other small metal objects, that can
make a connection from one terminal to another. Shorting the battery terminals
together may cause burns or a fire.
d) Under abusive conditions, liquid may be ejected from the battery; avoid
contact. If contact accidentally occurs, flush with water. If liquid contacts eyes,
additionally seek medical help. Liquid ejected from the battery may cause irritation or
burns.
6)Service
a) Have your power tool serviced by a qualified repair person using only identical
replacement parts. This will ensure that the safety of the power tool is maintained.
18V COMBI DRILL
ERI603COM
ADDITIONAL SAFETY RULES FOR YOUR COMBI DRILL
1. Wear ear protectors when use impact drilling. Exposure to noise can cause hearing
loss.
2. Use auxiliary handle(s), if supplied with the tool. Loss of control can cause personal
injury.
3. Hold power tool by insulated gripping surfaces, when performing an operation
where the cutting accessory may contact hidden wiring. Cutting accessory
contacting a “live” wire may make exposed metal parts of the power tool “live” and could
give the operator an electric shock.
4. Remove the battery pack from the drill before carrying out adjustments.
5. Do not expose to rain or water.
6. Do not store the battery pack in temperatures over 40oC.
7. Always charge the battery pack between temperatures 0oC to 30oC. Ideal charging
temperature is 18oC to 24oC.
8. Only use the charger and the battery pack provided no others.
9. Avoid short circuit of the battery pack connections (screws & nails).
10.Do not incinerate or burn the battery pack, it may explode.
11.Do not charge a damaged battery pack.
12.Replace any damaged supply cords on your charger.
13.Always disconnect the charger power supply before making or breaking the connections to
the battery pack.
14.Battery pack and charger will be warm during charging this is normal.
15.When not in use, remove a charged battery pack from the charger.
16.Always remove the battery pack from the charger immediately after re-charging is
completed.
17.Your drill and battery pack will be warm when working, this is normal.
18.Do not dispose of batteries in fire, or with household waste. Return exhausted batteries to
your local collection or recycling point.
19.Always check walls, floors and ceilings for hidden power cables and pipes.
20.Accessories and metal parts can become very hot.
FOR CHARGER
1. This appliance can be used by children aged from 8 years and above and persons with
reduced physical, sensory or mental capabilities or lack of experience and knowledge if
they have been given supervision or instruction concerning use of the appliance in a safe
way and understand the hazards involved. Children shall not play with the appliance.
Cleaning and user maintenance shall not be made by children without supervision.
2. If the charger supply cord is damaged, it must be replaced by the manufacturer, its service
agent or similarly qualified persons in order to avoid a hazard.
3. Charger is double insulated for additional electrical safety.
4. Charger is for indoor use only.
5. Never charge damaged batteries as these can short circuit and over heat.
6. When the charger is in use it MUST be supervised , if there is any evidence of overheating
then IMMEDIATELY disconnect the charger from the power supply.
7. If gas or smoke is emitted from the battery during charging switch off the power supply ,
and move to a well vented area to allow the fumes to vent to atmosphere.
Caution is there is leaking liquid from the battery wear protective clothing, glasses and
clothes as this can be acidic.
8. Always disconnect battery charger and remove battery from charger when the charging is
complete.
9. Only use the battery charger specifically stated on the base of the battery.
FOR BATTERY
1. Always remove the battery pack from the charger immediately after re-charging is
completed.
2. When not in use, remove a charged battery pack from the charger.
3. Do not charge a damaged battery pack.
4. Do not charge non-rechargeable batteries.
5. Do not install the battery backwards so the polarity is reversed.
6. Do not connect the positive terminal and negative terminal of the battery to each other with
any metal object (such as wire).
7. Do not carry or store battery together with necklaces, hairpins or other metal objects.
8. Do not pierce the battery with nails, strike the battery with a hammer, step on the battery or
otherwise subject it to strong impacts or shocks.
9. Do not solder directly onto the battery.
10.Do not expose battery to water or salt water, or allow the battery to get wet.
11.Do not disassemble or modify the battery. The battery contains safety and protection
devices, which, if damaged, may cause the battery to generate heat, explode or ignite. The
protection circuit module provided with battery packs is not to be used as a substitute for a
shut-off switch.
12.Do not place the battery in or near fire, on stoves or other high temperature locations. Do
not place the battery in direct sunlight, or use or store the battery inside cars in hot weather.
Heating the battery can damage the safety circuitry, which can cause additional heating,
rupture or ignition of the battery. Using the battery in this manner may also result in a loss of
performance and a shortened life expectancy.
13.Do not place the battery in microwave ovens, high-pressure containers or on induction
cookware.
14.If you intend to store a battery for a period without use then store battery at room
temperature (19°C to 25°C), charged to about 30 – 50% of capacity. When storing for very
long periods boost-charge the battery once per year to prevent over discharge.
15.Always charge the battery in a temperature range of 0°C to 30°C and discharge in a
temperature range of 0°C to 75°C.
16.The battery pack and charger will be warm during charging, this is normal.
17.Do not continue charging the battery if it does not recharge within the specified charging
time. Doing so may cause the battery to become hot, explode or ignite. The temperature
range over which the battery can be charged is 0°C to 30°C. Charging the battery at
temperatures outside this range may cause severe damage to the battery or reduce battery
life expectancy.
18.When the battery is worn out, insulate the terminals with adhesive tape or similar materials
before disposal.
19.Do not dispose of batteries in fire, or with household waste. Return exhausted batteries to
your local collection or recycling point.
Warning: If a small amount of electrolyte should leak from the battery pack
under extremes of temperature or after heavy use, then wash off immediately
from your skin and hands using clean water. For eye contact, rinse thoroughly with clean
water and seek medical treatment immediately.
18V COMBI DRILL
ERI603COM
ADDITIONAL SAFETY WARNING FOR CONSTRUCTION DUST
The updated Control of Substances Hazardous to Health Regulations 1st October 2012 now
also targets to reduce the risks associated with silica, wood and gypsum dusts.
Construction workers are one of the at-risk groups within this because of the dust that they
breathe: silica dust is not just a nuisance; it is a real risk to your lungs!
Silica is a natural mineral present in large amounts in things like sand, sandstone and granite. It
is also commonly found in many construction materials such as concrete and mortar. The silica
is broken into very fine dust (also known as Respirable Crystalline Silica or RCS) during many
common tasks such as cutting, drilling and grinding
Breathing in very fine particles of crystalline silica can lead to the development of:
Lung cancer
Silicosis
Chronic Obstructive Pulmonary Disorder (Chronic obstructive pulmonary disease (COPD))
And breathing in fine particles of wood dust can lead to the development of Asthma
The risk of lung disease is linked to people who regularly breathe construction dust over a
period of time, not on the odd occasion.
To protect the lung, the COSHH Regulations sets a limit on the amount of these dusts that you
can breathe (called a Workplace Exposure Limit or WEL) when averaged over a normal working
day. These limits are not a large amount of dust: when compared to a penny it is tiny – like a
small pinch of salt:
This limit is the legal maximum; the most you can breathe after the right controls have been
used.
How to reduce the amount of dust?
1 Reduce the amount of cutting by using the best sizes of building products.
2 Use a less powerful tool e.g. a block cutter instead of angle grinder.
3 Using a different method of work altogether – e.g. using a nail gun to direct fasten cable trays
instead of drilling holes first.
Please always work with approved safety equipment, such as those dust masks that specially
designed to filter out microscopic particles and use the dust extraction facility at all time.
For more information please see the HSE website:
http://www.hse.gov.uk/construction or http://www.hse.gov.uk/pubns/cis69.pdf
Warning: Some dust particles created by power sanding, sawing, grinding, drill
and other construction jobs contain chemicals known to cause cancer, birth
defects or other reproductive harm. Some examples of these chemicals are:
• Lead from lead-based paints.
• Crystalline silica from bricks and cement and other masonry products.
• Arsenic and chromium from chemically treated timber.
Your risk from these exposures varies, depending upon how often you do this type of work. To
reduce your exposure to these chemicals:
• Work in a well-ventilated area.
• Work with approved safety equipment, such as those dust masks that are specially designed
to filter microscopic particles.
VIBRATION
The European Physical Agents (Vibration) Directive has been brought in to help reduce
hand arm vibration syndrome injuries to power tool users. The directive requires power tool
manufacturers and suppliers to provide indicative vibration test results to enable users to make
informed decisions as to the period of time a power tool can be used safely on a daily basis
and the choice of tool.
Further Advice can be found at www.hse.gov.uk
Vibration total values (triax vector sum) determined according to EN 60745:
Impact drilling into concrete
Drilling into metal
ah,ID=11.4m/s²
Uncertainty K=1.5m/s²
ah,D=2.6m/s²
Uncertainty K=1.5m/s²
The declared vibration emission value should be used as a minimum level and should be used
with the current guidance on vibration.
Calculating the actual period of the actual period off use can be difficult and the HSE website
has further information.
The declared vibration emission been measured in accordance with a standardised test stated
above and may be used to compare one tool with another tool.
The declared vibration emission value may also be used in a preliminary assessment of
exposure.
Warning: The vibration emission value during actual use of the power tool can differ from
the declared value depending on the ways in which the tool is used dependant on the
following examples and other variations on how the tool is used:
How the tool is used and the materials being cut or drilled.
The tool being in good condition and well maintained.
The use the correct accessory for the tool and ensuring it is sharp and in good condition.
The tightness of the grip on the handles.
And the tool is being used as intended by its design and these instructions.
While working with this power tool, hand/arm vibrations occur. Adopt the correct
working practices in order to reduce the exposure to vibration.
This tool may cause hand-arm vibration syndrome if its use is not adequately
managed.
Warning: Identify safety measures to protect the operator that are based on an
estimation of exposure in the actual conditions of use (taking account of all parts of the
operating cycle such as the times when the tool is switched off and when it is running idle in
addition to the trigger time).Note The use of other tools will reduce the users’ total working
period on this tool.
Helping to minimise your vibration exposure risk.
ALWAYS use sharp chisels, drills and blades.
Maintain this tool in accordance with these instructions and keep well lubricated
(where appropriate).
18V COMBI DRILL
ERI603COM
Avoid using tools in temperatures of 10ºC or less.
Plan your work schedule to spread any high vibration tool use across a number of days.
Health surveillance
All employees should be part of an employer’s health surveillance scheme to help identity any
vibration related diseases at an early stage, prevent disease progression and help employees
stay in work.
Double insulation
The charger is double insulated. This means that all the external metal parts are electrically
insulated from the mains power supply. This is done by placing insulation barriers between the
electrical and mechanical components making it unnecessary for the tool to be earthed.
Vibration and noise reduction
To reduce the impact of noise and vibration emission, limit the time of operation, use lowvibration and low-noise operating modes as well as wear personal protective equipment.
Take the following points into account to minimize the vibration and noise exposure risks:
1. Only use the product as intended by its design and these instructions.
2. Ensure that the product is in good condition and well maintained.
3. Use correct application tools for the product and ensure they in good condition.
4. Keep tight grip on the handles/grip surface.
5. Maintain this product in accordance with these instructions and keep it well lubricated
(where appropriate).
6. Plan your work schedule to spread any high vibration tool use across a number of days.
Familiarise yourself with the use of this product by means of this instruction
manual. Memorise the safety directions and follow them to the letter. This will
help to prevent risks and hazards.
1. Always be alert when using this product, so that you can recognise and handle risks early.
Fast intervention can prevent serious injury and damage to property.
2. Switch off and disconnect from the power supply if there is any malfunction. Have the
product checked by a qualified specialist and repaired, if necessary, before you put it into
operation again.
Residual risks
Even if you are operating this product in accordance with all the safety requirements,
potential risks of injury and damage remain. The following dangers can arise in connection
with the structure and design of this product:
1. Health defects resulting from vibration emission if the product is being used over long
periods of time or not adequately managed and properly maintained.
2. Injuries and damage to property due to broken application tools or the sudden impact of
hidden objects during use.
3. Danger of injury and property damage caused by flying objects.
Warning: This product produces an electromagnetic field during operation! This field may
under some circumstances interfere with active or passive medical implants! To reduce
the risk of serious or fatal injury, we recommend persons with medical implants to consult their
doctor and the medical implant manufacturer before operating this product!
Important note:
Be sure the supply is the same as the voltage given on the rating plate for the charger. The
charger is fitted with a two-core cable and plug.
Remove the mains plug from socket before carrying out any adjustment or servicing.
SYMBOLS
To reduce the risk of injury, user must read instruction manual
Warning
Double insulation
Indoor use only
1h charging time for ERI606BAT
1h
Do not expose to rain or water
Do not burn
Wear gloves
max30 C
Always charge the battery pack between temperatures 0°C to 30°C. Ideal charging temperature is 18°C to 24°C.
This symbol indicates that this battery contains lithium. This battery shall be brought to your shop to be recycled.
Wear ear protection
Wear eye protection
Wear dust mask
Do not dispose of batteries, Return exhausted batteries to your local collection
or recycling point.
Waste electrical products should not be disposed of with household waste.
Please recycle where facilities exist. Check with your Local Authority
or retailer for recycling advice.
yyWxx Manufacturing date code; Year of manufacturing (20yy) and week of manufacturing
(Wxx);
18V COMBI DRILL
ERI603COM
1
2
10
9
3
4
5
8
7
1.
KEYLESS CHUCK
2.
TORQUE ADJUSTMENT RING
3. TWO-SPEED GEAR CONTROL
4.
FORWARD/REVERSE ROTATION CONTROL
5.
SOFT GRIP HANDLE
6.
BATTERY PACK *
7.
BATTERY PACK RELEASE BUTTON
8.
BELT HOOK
9.
ON/OFF SWITCH
10.
SIGHT LIGHT
6
* Not all the accessories illustrated or described are included in standard delivery.
TECHNICAL DATA
18V
Voltage
No load speed
Max*
0-400/0-1400/min
Impact rate
0-6400/0-22400bpm
Number of clutch positions
21+1+1
Max torque
40N.m
Chuck capacity
13mm
Charger Protection class
/II
Charging time
1hr
Charger Input
100-240V~50/60Hz,78W
Charger Output
Max drilling capacity
14.4-20V 3000mA
Masonry
13mm
Wood
35mm
Steel
10mm
Machine weight
1.49 Kg
Battery capacity
2.0Ah Li-ion battery
NOISE INFORMATION
A weighted sound pressure
LpA: 87.1dB(A)
A weighted sound power LwA: 98.1dB(A)
KPA & KWA3.0dB(A)
Wear ear protection when sound pressure is over 80dB(A)
ACCESSORIES
2.0 Ah Lithium Battery Pack(ERI606BAT)
1hr Charger (ERB607CHR)
Belt hook
18V COMBI DRILL
2pcs
1pc
1pc
ERI603COM
OPERATING INSTRUCTIONS
NOTE: Before using the tool, read the
instruction book carefully.
INTENDED USE:
The machine is intended for driving in and loosening
screws as well as for drilling in wood, metal and
plastic.
Fig. 1-1
BEFORE PUTTING INTO OPERATION
A) CHARGING THE BATTERY
The battery charger supplied is matched to the
Li-ion battery installed in the machine. Do not use
another battery charger.
The Li-ion battery is protected against deep
discharging. When the battery is empty, the machine
is switched off by means of a protective circuit: The
tool holder no longer rotates.
In a warm environment or after heavy use, the
battery pack may become too hot to permit
charging. Allow time for the battery to cool down
before recharging.
When the battery pack is charged for the first time
and after prolonged storage, the battery pack will
accept a 100% charge after several charge and
discharge cycles.
B) TO REMOVE THE BATTERY PACK (See Fig.
1-1)
Depress the Battery Pack Release Button firmly first
and then slide the Battery Pack out from your tool.
Fig. 1-2
Fig. 1-3
C) TO INSTALL THE BATTERY PACK (See Fig.
1-2)
Slide the fully charged Battery Pack onto the tool
with sufficient force until it clicks into position.
D) HOW TO CHARGE YOUR BATTERY PACK
(See Fig. 1-3)
CHARGING PROCEDURE
1) Plug the charger into an appropriate outlet. The
light will be green.
2) Slide the battery pack into the charger, the light
will turn to red to indicate the charging process has
started.
3) When charging is completed, the light will turn to
green. The pack is now fully charged, unplug the
charger and remove the battery pack.
WARNING:
When battery charge runs out after
continuously use or exposure to direct sunlight
or heat, allow time for the tool to cool down
before re-charging to achieve the full charge.
CHARGING INDICATOR
This charger is designed to detect some problems
that can arise with battery packs. Indicator lights
indicate problems (see table below). If this occurs,
insert a new battery pack to determine if the charger
is OK. If the new battery charges correctly, then the
original pack is defective and should be returned to
a service center or recycling service center. If the
new battery pack displays the same problem as the
original Battery Pack, have the charger tested at an
authorized service center.
Light
ON/OFF
flash
Red on
Fig. 1-2
Fig. 1-3
Status
Charging
Fig. 2-1
Red flash
- - - - -
Green on
Green flash
Defective Battery
Fully Charged
-- - - - -
Hot/Cold Delay
OPERATION
Fig. 2-2
1. HOW TO USE THE BELT HOOK (See Fig.
2-1&2-2)
Screw the Belt Hook on the tool with the screw
provided in the plastic bag. The Belt Hook can be
hooked on your belt or pocket, etc.
2. ON / OFF SWITCH (See Fig. 3)
Depress the On/Off switch to start and release it to
stop your drill. The on/off switch is fitted with a brake
function which stops your chuck immediately when
you quickly release the switch.
18V COMBI DRILL
Fig. 3
ERI603COM
Fig. 2-2
Fig. 3
It is also a variable speed switch that delivers higher
speed and torque with increased trigger pressure.
Speed is controlled by the amount of switch trigger
depression.
WARNING: Do not operate for long
periods at low speed because excess
heat will be produced internally.
3. SWITCH LOCK
The switch trigger can be locked in the OFF position.
This helps to reduce the possibility of accidental
starting when not in use. To lock the switch trigger,
place the rotation control in the center position.
4. REVERSIBLE (See Fig. 4-1&4-2)
For drilling and screw driving use forward rotation
marked “
” (lever is moved to the left). Only use
reverse rotation marked “
” (lever is moved to the
right) to remove screws or release a jammed drill bit.
WARNING: Never change the direction of
rotation when the chuck is rotating, wait
until it has stopped!
Fig. 4-1
Fig. 4-2
5. TWO-SPEED GEAR CONTROL (See Fig. 5)
The drill has a two-speed gear control designed for
drilling or driving at LO (mark is 1) or HI (mark is 2)
speeds. A slide switch is located on top of the drill
to select either LO or HI speed. When using the drill
in the LO speed range, the speed will decrease and
the drill will have greater power and torque. When
using the drill in the HI speed range, the speed
will increase and the drill will have less power and
torque.
Gear I
Low speed range: for screwdriving or working with
large drilling diameter
Gear II
High speed range: for working with small drilling
diameter
WARNING: To prevent gear damage,
always allow the chuck to come to a
complete stop before changing the direction of
rotation or the two-speed gear control.
Fig. 5
Fig. 5
6. CHUCK ADJUSTMENT (See Fig. 6)
To open the chuck jaws rotate the front section of
the chuck. Insert the drill bit between the chuck jaws
and rotate the front section in the opposite direction.
Ensure the drill bit is in the center of the chuck jaws.
Finally, firmly rotate the front chuck section in the
opposite directions. Your drill bit is now clamped in
the chuck.
7. TORQUE ADJUSTMENT (See Fig. 7)
(Screw driving force of your drill driver)
The torque is adjusted by rotating the torque
adjustment ring. The torque is greater when the
torque adjustment ring is set on a higher setting. The
torque is less when the torque adjustment ring is set
on a lower setting.
Make the setting as follows:
1-4
for driving small screws
5-9
for driving screws into soft material
10 - 14 for driving screws into soft and hard
material
15 - 20 for driving screws into hard wood
21
Fig. 6
Fig. 7
for driving larger screws
for heavy drilling
for drilling in masonry and concrete
8. AUTOMATIC SPINDLE LOCK (See Fig. 8)
The automatic spindle lock allows you to use it as
a regular screwdriver. You can give an extra twist
to firmly tighten a screw, loosen a very tight screw
or continue working when the battery energy has
expired. For manual screwdriver purposes, the
chuck is automatically locked when the tool is off.
Fig. 8
9. USING THE SIGHT LIGHT
To turn on the light simply press the on/off switch.
When you release the on/off switch, the light will be
off.
LED lighting increases visibility-great for dark or
enclosed area. LED is also a battery capacity
indicator. It will flash when power gets low.
18V COMBI DRILL
ERI603COM
10. DRILLING
When drilling into a hard smooth surface, use a
center punch to mark the desired hole location. This
will prevent the drill bit from slipping off center as
the hole is started. Hold the tool firmly and place
the tip of the bit at the point to be drilled. Depress
the switch trigger to start the tool. Move the drill bit
into the workpiece, applying only enough pressure
to keep the bit cutting. Do not force or apply side
pressure to elongate a hole.
If you want to activate the drill function (For drilling
metal wood or plastic), turn the torque adjustment
ring on the drill position. If you want to activate the
impact function(For masonry or concrete), turn the
torque adjustment ring on the hammer position.
TUNGSTEN carbide drill bits should
always be used for concrete and
masonry. When drilling in metal, only use
HSS drill bits in good condition. Always use a
magnetic bit holder (not included) when using
short screwdriver bits. When screw-driving,
apply a small quantity of liquid soap or similar
to the screw threads to ease insertion.
11. DISPOSAL OF AN EXHAUSTED BATTERY
PACK
To preserve natural resources, please recycle
or dispose of the battery pack properly. This
battery pack contains Lithium batteries.
Consult your local waste authority for information
regarding available recycling and/or disposal
options. Discharge your battery pack by operating
your drill, then remove the battery pack from the drill
housing and cover the battery pack connections
with heavy-duty adhesive tape to prevent short
circuit and energy discharge. Do not attempt to
open or remove any of the components.
12. OVERLOAD PROTECTION
When overloaded, the motor comes to a stop.
Relieve the load on the machine immediately and
allow cooling for approx. 30 seconds at the highest
no-load speed.
13. TEMPERATURE DEPENDENT OVERLOAD
PROTECTION
When using as intended for the power tool cannot
be subject to overload. When the load is too high
or the allowable battery temperature of 75 °C is
exceeded, the electronic control switches off the
power tool until the temperature is in the optimum
temperature range again.
14. PROTECTION AGAINST DEEP DISCHARGING
The Li-ion battery is protected against deep
discharging by the “Discharging Protection System”.
When the battery is empty, the machine is switched
off by means of a protective circuit: The inserted tool
no longer rotates.
PROBLEM SOLUTION
1. WHY DOES THE DRILL NOT TURN ON WHEN
YOU PRESS THE SWITCH?
The forward/reverse rotation control, which is on
top of the trigger, is positioned in the lock function.
Unlock the forward/reverse rotation control by
putting it into the required rotation position. Push the
trigger and the drill will start to rotate.
2. THE DRILL STOPS BEFORE THE SCREW IS
COMPLETELY TIGHTENED. WHY?
Verify the torque position of the torque adjusting
ring, you can find the torque-adjusting ring between
the chuck and the drill body. Position 1 is the lowest
torque (screw driving force) and position 21 is the
highest torque (screw driving force). Position is for
drill operation. Regulate the torque adjusting ring to
a higher position to reach the best result.
3. REASONS FOR DIFFERENT BATTERY PACK
WORKING TIMES
Charging time problems, as above, and having not
used a battery pack for a prolonged time will reduce
the battery pack working time. This can be corrected
after several charge and discharge operations by
charging & working with your drill. Heavy working
conditions such as large screws into hard wood will
use up the battery pack energy faster than lighter
working conditions. Do not re-charge your battery
pack below 0oC and above 45oC as this will affect
performance.
18V COMBI DRILL
ERI603COM
MAINTENANCE
Your tool requires no additional lubrication or
maintenance.
There are no user serviceable parts in your power
tool. Never use water or chemical cleaners to clean
your power tool. Wipe clean with a dry cloth. Always
store your power tool in a dry place. Keep the motor
ventilation slots clean. Keep all working controls free
of dust. Occasionally you may see sparks through
the ventilation slots. This is normal and will not
damage your power tool.
ENVIRONMENTAL PROTECTION
Waste electrical products should not be
disposed of with household waste. Please
recycle where facilities exist. Check with your
Local Authority or retailer for recycling advice. For
further information visit www.recycle-more.co.uk.
PLUG REPLACEMENT
(UK & IRELAND ONLY)
If you need to replace the fitted plug then follow the
instructions below.
IMPORTANT
The wires in the mains lead are coloured in accordance
with the following code:
BLUE =NEUTRAL
Brown = Live
As the colours of the wires in the mains lead of this
appliance may not correspond with the coloured
markings identifying the terminals in your plug,
proceed as follows. The wire which is coloured blue
must be connected to the terminal which is marked
with N. The wire which is coloured brown must be
connected to the terminal which is marked with L.
Warning:
Never connect live or neutral wires to the earth
terminal of the plug. Only fit an approved 5AMP
BS1363/A plug and the correct rated fuse.
Note: If a moulded plug is fitted and has to be
removed take great care in disposing of the plug
and severed cable, it must be destroyed to prevent
engaging into a socket.
5 Amp fuse approved
to BS1362
Connect
Blue to N
(neutral)
Outer sleeve
firmly clamped
Brown L(live)
Cable grip
18V COMBI DRILL
ERI603COM
DECLARATION OF CONFORMITY
We, Importer
Erbauer (UK) Ltd BA22 8RT
Declare that the product
Description: 18V COMBI DRILL
Model: ERI603COM
Complies with the following directives,
EC Machinery Directive 2006/42/EC
EC Low Voltage Directive 2006/95/EC
EC Electromagnetic Compatibility Directive 2004/108/EC
Restrictions of the Use of Certain Hazardous Substances in Electrical and Electronic Equipment 2011/65/EU
Waste Electrical and Electronic Equipment (WEEE) 2012/19/EU
Standards and technical specifications referred to:
EN 55014-1
EN 55014-2
EN 60745-1
EN 60745-2-1
EN 60745-2-2
EN 60335-1
EN 60335-2-29
EN 61000-3-2
EN 61000-3-3
EN 62233
Authorised Signatory and technical file holder
Date: 08/18/2014
Signature:
Name / title: Peter Harries / Quality Manager
Erbauer (UK) Ltd. Trade House, Mead Avenue, BA22 8RT
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement