TVIP V4 Part Number: PT398-60080

TVIP V4 Part Number: PT398-60080
TOYOTA
LAND CRUISER
2008 -
Preparation
TVIP V4
REMOTE ENGINE STARTER (RES)
Part Number: PT398-60080
NOTE: Part number of this accessory may not be the same as
the part number shown.
Conflicts
Recommended Tools
Do not install into vehicles without RKE systems.
Recommended Sequence of Application
Item #
1
2
Accessory
XM
TVIP
XM Radio
V2 Glass Breakage Sensor (GBS)
and/or
V4 Remote Engine Starter (RES)
Kit Contents
Item #
1
2
3
Quantity
1
1
1
Description
Wire Harness
RES ECU Bracket
Extra Large Wire Tie
Quantity
1
1
1
1
15
1
2
1
2
2
2
1
13
14
15
16
2
2
2
1
17
1
Quantity
1
Terminal Tension Blade
(PPO Only)
Installation Tools
Screwdriver
Side Cutters
Torque Wrench
Utility Knife
Pliers
Tape
Wrench
Pick (dealers only)
Socket
Special Chemicals
Cleaner
Glass Cleaner
Description
RES ECU
Gateway ECU
Gateway ECU Bracket
M6 Tapping Screw
Wire Ties
Waterproof Sheet
Large Foam Tape
Custom Double Stick Tape
Key Tag (English)
Window Labels (English)
Transmitter Labels (English)
Warning Label for Engine
Compartment (English)
Key Tag (Spanish)
Window Labels (Spanish)
Transmitter Labels (Spanish)
Warning Label for Engine
Compartment (Spanish)
Owner’s Guide
Notes
(Optional)
Blankets, Parts Boxes
Notes
Software version 2.00.008 or
later
Toyota SST # 00002-025BL-01
Notes
#2 Phillips, Flat Blade Jeweler’s
e.g. Panel Pry Tool #1
Toyota SST # 00002-06001-01
36 in•lbf (4.07 N•m)
Clip Clamp Pliers
Clear
10mm
Wire Pick Set
10mm, Extension, 10mm Deep
Notes
VDC Approved Cleaner
Household Windex
Legend
Additional Items Required For Installation
Item #
1
Techstream
Nylon Panel Removal Tool
Hardware Bag Contents
Item #
1
2
3
4
5
6
7
8
9
10
11
12
Personal & Vehicle
Protection
Safety Glasses
Safety Gloves
Vehicle Protection
Special Tools
Description
Black Electrical Tape
STOP: Damage to the vehicle may occur. Do not
proceed until process has been complied with.
OPERATOR SAFETY: Use caution to avoid risk of
injury.
CAUTION: A process that must be carefully observed
in order to reduce the risk of damage to the
accessory/vehicle and to ensure a quality installation.
TOOLS & EQUIPMENT: Used in Figures calls out the
specific tools and equipment recommended for this
process.
REVISION MARK: This mark highlights a change in
installation with respect to previous issue.
Care must be taken when installing this accessory to ensure damage does not occur to the vehicle. The installation of this
accessory should follow approved guidelines to ensure a quality installation
These guidelines can be found in the "Accessory Installation Practices" document.
This document covers such items as:
• Vehicle Protection (use of covers and blankets, cleaning chemicals, etc.)
• Safety (eye protection, rechecking torque procedure, etc.)
• Vehicle Disassembly/Reassembly (panel removal, part storage, etc.)
• Electrical Component Disassembly/Reassembly (battery disconnection, connector removal, etc.)
Please see your Toyota dealer for a copy of this document
Issue: B
10/8/07
Page 1 of 29 pages
2P WHITE
C (Male)
LAND CRUISER
White Tape Marker
1P WHITE
(RES Diagnosis)
D 5P WHITE
E
WIRE TERMINAL
(Red Wire)
F
WIRE TERMINAL
(White/Red Wire)
TOYOTA
10/8/07
B
Procedure
Issue: B
A 20P BLUE
H GATEWAY ECU
GROUND WIRE
TERMINAL
J
10P WHITE
20P WHITE
K (for RES ECU)
L
RES ECU
TVIP V4
REMOTE ENGINE STARTER (RES)
I
2008 -
Page 2 of 29 pages
5P WHITE
G (for Gateway ECU)
TOYOTA
LAND CRUISER
2008 -
Procedure
TVIP V4
REMOTE ENGINE STARTER (RES)
1. Vehicle Disassembly.
(a) Place the Vehicle in Park with the Parking
Brake set.
10mm Socket
Negative
Battery
Cable
(b) Remove the Negative Battery Cable.
(Fig. 1-1)
(1) Protect the Fender before starting.
(2) Note the Battery Cable position, as it will be reinstalled in the same position.
CAUTION: Do not touch the positive terminal.
Fig. 1-1
Remove all corresponding
connectors accordingly as
you disassembly.
Fig. 1-2
Issue: B
10/8/07
Page 3 of 29 pages
TOYOTA
LAND CRUISER
2008 -
Procedure
TVIP V4
REMOTE ENGINE STARTER (RES)
(c) Remove the Glove Box Under Cover.
(Fig. 1-3)
Nylon Panel Removal Tool
(1) Begin by protecting the Vehicle Interior with
Blankets.
Glove Box Under Cover
Fig. 1-3
Nylon Panel Removal Tool
(d) Remove the Passenger’s Dash Side Cover.
(Fig. 1-4)
Dash Side Cover
Fig. 1-4
Nylon Panel Removal Tool
(e) Remove the Passenger’s Step Cover.
(Fig. 1-5)
Step Cover
Fig. 1-5
Nylon Panel Removal Tool
Cowl Cover
(f) Remove the Passenger’s Cowl Cover.
(Fig. 1-6)
(1) Remove 1 Nut.
Nut
Fig. 1-6
Issue: B
10/8/07
Page 4 of 29 pages
TOYOTA
LAND CRUISER
2008 -
Procedure
TVIP V4
REMOTE ENGINE STARTER (RES)
(g) Remove the Passenger’s Knee Panel
(Fig. 1-7)
Nylon Panel Removal Tool
Knee Pad
Fig. 1-7
(h) Remove the Passenger’s Cluster Side Panel.
(Fig. 1-8)
Phillips Screwdriver
(1) Remove 1 Screw and 1 Clip.
Screw
Clip
Cluster
Side
Fig. 1-8
10mm Socket
Knee Air Bag
(i) Remove the Passenger’s Knee Air Bag.
(Fig. 1-9)
(1) Remove 4 Bolts.
(2) Do not disconnect the Vehicle’s Connector.
CAUTION: Sharp metal edges.
Bolts (x2)
Bolts (x2)
Fig. 1-9
Knee Air Bag
(j) Wrap the Passenger’s Knee Air Bag in a
Blanket and use the TVIP Kit Box to
support it. (Fig. 1-10)
CAUTION: Sharp metal edges.
Fig. 1-10
Issue: B
TVIP Box
10/8/07
Page 5 of 29 pages
TOYOTA
LAND CRUISER
2008 -
Procedure
TVIP V4
REMOTE ENGINE STARTER (RES)
(k) Remove 2 Screws from the bottom of the
Glove Box. (Fig. 1-11)
Phillips Screwdriver
Fig. 1-11
Screws (x2)
Nylon Panel Removal Tool, 10mm Socket
Cover
Screw
(l) Open the Glove Box Door, then remove 2
Bolt Covers from the Glove Box.
(Fig. 1-12)
(m) Dislodge the Glove Box(Fig. 1-12)
Screw
(1) Remove 2 Bolts.
Cover
Fig. 1-12
Glove Box
(n) Remove the Vehicle Harness from the
backside of the Glove Box, then remove the
Glove Box. (Fig. 1-13)
Glove Box
(backside)
(1) Disconnect any Connectors.
Vehicle Harness
Fig. 1-13
10mm Socket
Knee Air Bag
(o) Temporarily install the Passenger's Knee
Air Bag. (Fig. 1-14)
CAUTION: Sharp metal edges.
Bolts (x2)
Bolts (x2)
Fig. 1-14
Issue: B
10/8/07
Page 6 of 29 pages
TOYOTA
LAND CRUISER
2008 -
Procedure
TVIP V4
REMOTE ENGINE STARTER (RES)
IF EQUIPPED VEHICLE WITH
NAVIGATION SYSTEM.
10mm Deep Socket, Clip Clamp Pliers
DVD
Nut
Screw
(p) Remove the DVD Unit from the Glove Box
Area. (Fig. 1-15)
(1) Remove 2 Screws and 1 Nut.
(2) Using the Clip Clamp Tool or the like, push on
the inside the Vehicle Clamp, and release it
from the DVD Unit.
Clamp
Fig. 1-15
Screw
Brace
2. V4 Wire Harness Installation.
V4 Harness
V4 Harness
(a) Route the V4 Harness behind the Vehicle
Brace and Yellow Harness in the Glove
Box area as shown. (Fig. 2-1)
CAUTION: Sharp metal edges.
White Tape
Vehicle’s Yellow Harness
Fig. 2-1
Side Cutter
Wire Ties (x3)
(b) Secure the V4 Harness's White Taped
Marker to the Reinforcement with 1 Wire
Tie. (Fig. 2-2)
V4 Harness’
White Tape
Marker
Fig. 2-2
V4 Harness
(c) Secure the V4 Harness to the
Reinforcement with 2 Wire Ties.
(Fig. 2-2)
5P
10mm Socket
Vehicle’s Ground Terminal
(d) Locate and remove 1 Bolt from the Vehicle
Ground Terminal in the upper left side of
the Glove Box Area. (Fig. 2-3)
(1) Do not discard the Bolt.
Bolt
Fig. 2-3
Issue: B
V4 Harness’s Ground Terminal
10/8/07
Page 7 of 29 pages
TOYOTA
LAND CRUISER
2008 -
Procedure
TVIP V4
REMOTE ENGINE STARTER (RES)
10mm Socket
V4 Harness's Ground Terminal
Vehicle's
Ground
Terminal
(e) Use the existing Vehicle's Bolt to secure the
V4 Harness's Ground Terminal with the
Vehicle's Ground Terminal. (Fig. 2-4)
(1) Make sure that the Vehicle's Ground Terminal
Pin seats properly.
Bolt
Fig. 2-4
(f) Locate and remove the Vehicle's White 10P
Connector on the Connector Block in the
Glove Box Area. (Fig. 2-5)
Vehicle’s 10P
(White)
Passenger's Side
Connector Block
Fig. 2-5
V4 Harness'
White 10P
Vehicle Harness'
White 10P
(g) Plug in the V4 Harness’ White 10P
Connectors between the Vehicle Harness’s
White 10P Connector and the Connector
Block. (Fig. 2-6)
V4 Harness'
White 10P
(1) Verify secure connection.
V4 Harness
Passenger's Side
Connector Block
Fig. 2-6
(h) Push the 10P Connectors through the
opening between the Vehicle Harness and
the Passenger's Side Connector Block as
shown. (Fig. 2-7)
Vehicle
Harness
10P
Fig. 2-7
Issue: B
V4 Harness
Passenger's Side
Connector Block
10/8/07
Page 8 of 29 pages
TOYOTA
LAND CRUISER
2008 -
Procedure
TVIP V4
REMOTE ENGINE STARTER (RES)
(i) Secure the 10P Connectors to the Vehicle
Harness with 1 Wire Tie. (Fig. 2-8)
Side Cutter
Wire
V4
Vehic
le
10P
Wire Tie
(j) Secure the V4 Harness to the Vehicle
Harness behind the Passenger's Side
Connector Block with 1 Wire Tie.
(Fig. 2-8)
Vehicle Harness
Fig. 2-8
(k) Wrap the V4 Harness’s branch area with 1
Large Foam Tape as shown. (Fig. 2-9)
Large
Foam
Tape
V4
Fig. 2-9
(l) Route the V4 Harness's White 20P
Connector toward the Vehicle's Floor.
(Fig. 2-9)
V4 20P (White)
3. RES ECU Preparation and Installation.
Double-Side Adhesive Tape
Yellow Sheet
(Vehicle Side)
(a) Remove the Clear Protective Sheet from the
Double Stick Tape and attach it to the Part
Number Label side of the RES ECU as
shown. (Fig. 3-1)
(1) Be sure to apply the Clear Sheet side on the
RES ECU.
Clear Sheet
(RES ECU Side)
Fig. 3-1
(2) Be sure to attach adhesive tape on the part
number label side of the RES ECU.
RES ECU
Part Number Label
(3) Do not cover the Part Number Labe with the
adhesive tape.
CAUTION: Do not touch the adhesive surface.
Issue: B
10/8/07
Page 9 of 29 pages
TOYOTA
LAND CRUISER
2008 -
Procedure
TVIP V4
REMOTE ENGINE STARTER (RES)
Waterproof Sheet
(b) Remove the Backing Sheet of 1 Waterproof
Sheet and attach it to the RES ECU near the
connectors as shown.
(Fig. 3-2)
CAUTION: Do not touch the adhesive surface.
RES ECU
Fig. 3-2
(c) Insert the RES ECU Bracket into the
indicated Bracket Slots on the RES ECU.
(Fig. 3-3)
RES ECU Bracket
(1) Ensure the Bracket is firmly attached to the
ECU.
RES ECU
Fig. 3-3
(d) Apply 1 strip of Large Foam Tape to the
RES ECU as shown. (Fig. 3-4)
Large Foam
Tape
RES ECU
Fig. 3-4
(e) Turn over the Floor Carpet on the left side
of the Passenger's Side Area. (Fig. 3-5)
(f) Pull back the Felt on the backside of the
Floor Carpet as shown. (Fig. 3-5)
(1) Do not remove or cut off the Felt.
Felt
Floor Carpet
Fig. 3-5
Issue: B
10/8/07
Page 10 of 29 pages
TOYOTA
LAND CRUISER
2008 -
Procedure
TVIP V4
REMOTE ENGINE STARTER (RES)
Bolt
V4 Harness
Portion of the
Protective
Bracket
Floor Carpet
RES ECU
(h) Using the VDC approved cleaner and
Cleaning Method, clean the area indicated
on the left side of the Passenger Side Floor.
(Fig. 3-6)
(i) Remove the Protective Sheet of the Double
Stick Tape. (Fig. 3-6)
20P
Fig. 3-6
(g) Connect the V4 Harness's White 20P
Connector to the RES ECU. (Fig. 3-6)
(j) Center the RES ECU Bracket to Vehicle's
Bolt as shown. Then press the RES ECU
firmly to the Vehicle. (Fig. 3-6)
(1) Do not attempt to reposition the ECU once
placed.
Side Cutter
Vehicle’s Brace
V4 Harness
Extra
Large
Wire
Tie
(k) Run 1 Extra Large Wire Tie through the
RES ECU rectangular hole and behind the
Vehicle Brace. Then secure it. (Fig. 3-7)
(1) Do not tighten the Wire Tie, it should hang
freely.
RES ECU
ECU Bracket’s
Fig. 3-7 Rectangular Hole
Side Cutter
Wire Tie
Vehicle’s Brace
V4 Harness
(l) Secure the V4 Harness to the side of the
inside Vehicle Brace with 1 Wire Tie as
shown. (Fig. 3-8)
(1) Do not use the front hole of the Vehicle Brace.
Hole
RES ECU
Fig. 3-8
Issue: B
10/8/07
Page 11 of 29 pages
TOYOTA
LAND CRUISER
2008 -
Procedure
TVIP V4
REMOTE ENGINE STARTER (RES)
(m) Attach 1 Large Foam Tape to the Vehicle’s
Brace and the V4 Harness as shown. Then
put the Carpet back. (Fig. 3-9)
Large Foam Tape
Vehicle’s Brace
GO BACK TO THE V4 HARNESS’S
WHITE TAPE AREA.
RES ECU
Carpet
Fig. 3-9
4. Gateway ECU Preparation and Installation.
Gateway ECU Bracket
Gateway ECU
Connector
(a) Insert the Gateway ECU Bracket into the
indicated Bracket Slots on the Gateway
ECU. (Fig. 4-1)
(1) Ensure the Bracket is firmly attached to the
ECU.
Fig. 4-1
10mm Socket
V4 Harness
Hole
(b) Connect the V4 Harness' White 5P
Connector to the Gateway ECU. (Fig. 4-2)
(1) Verify the secure connection.
Pin
5P
Fig. 4-2
Tapping Screw
Gateway ECU
(c) Using the M6 Tapping Screw from the Kit,
to install the Gateway ECU Bracket.
(Fig. 4-2)
(1) Make sure that the Bracket Pin seats properly.
CAUTION: Do not crimp the V4 and/or the V2
Harness between the Gateway ECU Bracket and
the Vehicle Reinforcement Brace.
Issue: B
10/8/07
Page 12 of 29 pages
TOYOTA
LAND CRUISER
2008 -
Procedure
5. V4 Wire Harness Installation (continued).
Brace
Side Cutter
V4 Harness
Wire Ties (x3)
V4 Male 2P (White)
(a) Route the V4 Harness along the
Reinforcement behind the Vehicle Brace in
the Glove Box Area. Secure the V4 Harness
to the hole of the Vehicle’s Brace with 1
Wire Tie. (Fig. 5-1)
(b) Route the V4 harness behind the vehicle
harness as shown. Secure it to the Vehicle
Harness with 2 Wire Ties. (Fig. 5-1)
Fig. 5-1
Side Cutter
V4 Male
2P (White)
V4 5P (White)
V4 20P (Blue)
V4 White/Red
and Red Wires
(c) Route the V4 Harness's 5P Connector,
White/Red and Red Wires as shown.
(Fig. 5-2)
Wire Tie
V4 Harness
Fig. 5-2
(d) Route the V4 Harness's Blue 20P
Connectors to the Passenger Side Cowl
Area securing it to the Vehicle Harness with
1 Wire Tie. (Fig. 5-2)
V4 20P (Blue)
Tape
(e) Locate the Vehicle's pre-wire White 2P
Connector in the right side of the Glove
Box Area. (Fig. 5-3)
(f) Remove the Tape securing the 2P
Connector. (Fig. 5-3)
Fig. 5-3
Issue: B
TVIP V4
REMOTE ENGINE STARTER (RES)
Vehicle's 2P Connector
10/8/07
Page 13 of 29 pages
TOYOTA
LAND CRUISER
2008 -
Procedure
TVIP V4
REMOTE ENGINE STARTER (RES)
Side Cutter
V4 Harness
Vehicle's 2P White
(g) Connect the V4 Harness's 2P Connector to
the Vehicle Harness' 2P connector.
(Fig. 5-4)
(1) Verify secure connection.
V4 2P White
(h) Secure the 2P Connectors and excess V4
Harness to the Vehicle Harness with 1 Wire
Tie. (Fig. 5-4)
Wire Tie
Fig. 5-4
10mm Socket
(i) Locate the Connector Block on the right side
of the Blower Motor Housing, then remove
the Connector Cover from the Connector
Block. (Fig. 5-5)
Connector Cover
(1) Do not break the Connector Cover.
(j) Loosen the center Bolt of the Connector
Block. (Fig. 5-5)
Connector Block
Fig. 5-5
Vehicle Harness
Tape
(k) Peel off the Tape secured from the Vehicle
Harness's Gray 18P and the White 18P
Connectors. (Fig. 5-6)
18P
(Gray)
(1) Do not cut the Vehicle Wires.
Tape
18P
(White)
Fig. 5-6
Flat Blade Jeweler’s, Screwdriver, Terminal Tension
Blade (PPO only), Wire Pick Set
(1) Do not remove the Terminal Lock.
Wire Removal Tool
Terminal Lock
18P (White)
Hole
Pin Side View
18P (White)
Fig. 5-7
Issue: B
Vehicle Harness’s
RED Wire
10/8/07
(l) Locate the White 18P Connector in the
Connector Block, then release the Terminal
Lock on the 18P Connector.
(Fig. 5-7)
RED
Wire Side View
(m) Locate the Vehicle Harness’ RED Wire in
the White 18P Connector. (Fig. 5-7)
(n) Using the Wire Removal Tool or the like,
pull out the Terminal for the RED Wire.
(Fig. 5-7)
Page 14 of 29 pages
TOYOTA
LAND CRUISER
2008 -
Procedure
TVIP V4
REMOTE ENGINE STARTER (RES)
18P (White)
Terminal Lock
V4 Harness’s
RED Wire
Wire Side View
(o) Insert the V4 Harness’ RED Wire Terminal
into the Vehicle’s White 18P Connector as
shown. (Fig.5-8)
(1) Verify the Terminal is inserted and seated
properly.
(p) Close the Terminal Lock. (Fig. 5-8)
RED
18P (White)
Fig. 5-8
Flat Blade Jeweler’s Screwdriver
(q) Disconnect the V4 Harness' Empty White 5P
Connector as shown. (Fig. 5-9)
V4 5P (White)
Terminal Lock
(r) Release the Terminal Lock on the Empty 5P
Connector. (Fig. 5-9)
(1) Do not remove the Terminal Lock.
Empty Female 5P
Fig. 5-9
V4 5P
(s) Insert the removed Vehicle’s RED Wire
Terminal into the V4 Empty 5P Connector
as shown. (Fig.5-10)
Wire Side View
(2) Do not close the Terminal Lock yet.
Connector Lock
Fig. 5-10
Vehicle Harness’s
RED Wire
Flat Blade Jeweler’s, Screwdriver, Terminal Tension
Blade (PPO only), Wire Pick Set
Wire Removal Tool
Terminal Lock
18P (Gray)
Hole
Issue: B
Vehicle Harness’s
RED Wire
10/8/07
(t) Locate the Gray 18P Connector in the
Connector Block, then release the Terminal
Lock on the 18P Connector.
(Fig. 5-11)
(1) Do not remove the Terminal Lock.
(u) Locate the Vehicle Harness’ RED Wire in
the Gray 18P Connector. (Fig. 5-11)
RED
Pin Side View
18P (Gray)
Fig. 5-11
(1) Verify the Terminal is inserted and seated
properly.
Wire Side View
(v) Using the Wire Removal Tool or the like,
pull out the Terminal for the RED Wire.
(Fig. 5-11)
Page 15 of 29 pages
TOYOTA
LAND CRUISER
2008 -
Procedure
TVIP V4
REMOTE ENGINE STARTER (RES)
(w) Insert the V4 Harness’ WHITE/RED Wire
Terminal into the Vehicle’s Gray 18P
Connector as shown. (Fig.5-12)
Terminal Lock
V4 Harness’s
WHITE/RED
Wire
18P (Gray)
(1) Verify the Terminal is inserted and seated
properly.
(x) Close the Terminal Lock. (Fig. 5-12)
Wire Side View
Fig. 5-12
Terminal Lock
V4 5P
(y) Insert the removed Vehicle’s RED Wire
Terminal into the V4 Empty 5P Connector
as shown. (Fig.5-13)
V4 5P
Vehicle Harness’s
RED Wire
(1) Verify the Terminal is inserted and seated
properly.
Wire Side View
(z) Close the Terminal Lock. (Fig. 5-13)
Connector Lock
Fig. 5-13
(aa) Connect the V4 Harness’s 5P Connectors.
(Fig. 5-14)
(bb) Reconnect the Connector Block, then
tighten the center Bolt of the Connector
Block. (Fig. 5-14)
V4
V4 5P
(1) Verify secure connection.
Connector Block
Connector Cover
(cc) Reinstall the Connector Cover onto the
Connector Block. (Fig. 5-14)
Fig. 5-14
Side Cutter
V4 Harness
5P Connectors
(dd) Secure the V4 Harness's 5P Connectors to
the Vehicle Harness with 1 Wire Tie.
(Fig. 5-15)
(ee) Secure the V4 Harness to the Vehicle
Harness with 1 Wire Tie. (Fig. 5-15)
Wire Ties (x2)
V4 20P
Connector Block
V4 20P
Fig. 5-15
Issue: B
10/8/07
Page 16 of 29 pages
TOYOTA
LAND CRUISER
2008 -
Procedure
TVIP V4
REMOTE ENGINE STARTER (RES)
(ff) Locate and disconnect the Vehicle’s
Harness Blue 20P Connector from the
Passenger Side Cowl Area. (Fig. 5-16)
Vehicle’s
20P (Blue)
Fig. 5-16
Vehicle’s 20P (Blue)
V4 Harness
20P
(gg) Plug in the V4 Harness' Blue 20P
Connectors between the Passenger Side
Connector Block Blue 20P Connector.
(Fig. 5-17)
(1) Verify secure connection.
20P
Fig. 5-17
Side Cutter
(hh) Use 1 Wire Tie to secure the 20P
Connectors to the Vehicle Harness.
(Fig. 5-18)
V4 Harness
V4 Harness’
Diagnostic
Connectors
20P
Wire Tie
Fig. 5-18
6. Partial Reassembly.
(a) Reassemble the Vehicle, except for the
Passenger's Cowl Cover, and Step Cover.
(1) Reconnect any disconnected connectors.
(2) Torque the Passengers Knee Air Bag to 7 ft•lbf
(10 N•m)
(b) Verify the Short Pin is installed. (Fig. 6-1)
Fig. 6-1
Issue: B
Install Short Pin
10/8/07
(1) If not install the Short Pin.
Page 17 of 29 pages
TOYOTA
LAND CRUISER
2008 -
Procedure
TVIP V4
REMOTE ENGINE STARTER (RES)
7. Registration Process.
EXAMPLE
(a) Open the Hood. (Fig. 7-1)
Do not close the Hood during the Registration
Setting Procedure. (Steps b-cc)
Fig. 7-1
(b) Temporarily reconnect the Vehicle's
Negative Battery Cable. (Fig. 7-2)
Negative Battery Cable
CAUTION: Do not touch the positive terminal.
Battery
Fig. 7-2
RES
Diagnostic 1P
Connectors
V4 Harness
(c) Locate the V4 Harness’s 1P RES
Diagnostic Connectors in the Passenger
Side Cowl Area, and remove the Tape.
(Fig. 7-3)
(d) Connect the 2 RES Diagnostic Connectors.
(Fig. 7-3)
Fig. 7-3
Issue: B
10/8/07
Page 18 of 29 pages
TOYOTA
LAND CRUISER
2008 -
Procedure
TVIP V4
REMOTE ENGINE STARTER (RES)
EXAMPLE
(e) Ensure all Doors are closed and the Smart
Key is in your possession. (Fig. 7-4)
(f) Cycle the Smart Key Ignition Button from
“OFF” to “ON” 5 times. (Fig. 7-4)
(1) Place the Shift Lever in the "P" (parking) or "N"
(neutral) Position.
NOTE: One cycle consists of:
OFFAccessoryON
This is equivalent to pressing the Smart Key
Ignition Button 14 times.
Fig. 7-4
(g) Once the fifth cycle has been completed, the
Hazard Lights Flash once. (Fig. 7-4)
(h) Press the Smart Key Ignition Button once
more to turn the ignition to OFF.
EXAMPLE
SUCCESS
(i) Start the Engine, after 10 seconds stop the
Engine. (Fig. 7-5)
(j) The Hazard Lights flash once. Registration
is completed. (Fig. 7-5)
Go to step m.
Fig. 7-5
RES Diagnostic
1P Connectors
(k) If you fail this procedure, the Hazard Lights
flash twice.
(l) Disconnect the RES Harness white 1P
Connector from the Passenger Side Cowl
Area. (Fig. 7-6)
Start again from step b.
Fig. 7-6
Issue: B
10/8/07
Page 19 of 29 pages
TOYOTA
LAND CRUISER
2008 -
Procedure
TVIP V4
REMOTE ENGINE STARTER (RES)
Vehicle Diagnostic Port
Techstream
Notebook
(m) Connect the Techstream
Notebook to the Vehicles
Diagnostic Port. (Fig. 7-7)
(n) With the Remote Control
Key in your possession,
press the Power Button
twice to select the Ignition
“ON” position.
(o) Start the TIS Techstream
Application by clicking on
the shortcut located on the
Desktop.
Fig. 7-7
(p) Click “Connect to Vehicle”.
(Fig. 7-8)
Fig. 7-8
(q) Confirm that the
information displayed on
the Vehicle Connection
Wizard is correct for the
Vehicle. If not verify that
the Techstream is properly
connected.
(Fig. 7-10)
(r) Click “Next>.” (Fig. 7-9)
Fig. 7-9
Issue: B
10/8/07
Page 20 of 29 pages
TOYOTA
LAND CRUISER
2008 -
Procedure
TVIP V4
REMOTE ENGINE STARTER (RES)
(s) Select Smart Key.
(Fig. 7-10)
(t) Click
. (Fig. 7-10)
Fig. 7-10
(u) Select “ECU
Communication ID
Registration.” (Fig. 7-11)
(v) Click
. (Fig. 7-11)
Fig. 7-11
(w) Confirm that the Engine is
ON (IG), and that the Smart
Cancel Function is OFF.
(Fig. 7-12)
(x) Click “Next>” to continue.
(Fig. 7-12)
Fig. 7-12
Issue: B
10/8/07
Page 21 of 29 pages
TOYOTA
LAND CRUISER
2008 -
Procedure
TVIP V4
REMOTE ENGINE STARTER (RES)
(y) Select “Remote Engine
Starter.” (Fig. 7-13)
(z) Click “Next>” to continue.
(Fig. 7-13)
Fig. 7-13
(aa) Click “Exit.” (Fig. 7-14)
Fig. 7-14
(bb) Click
Example
Fig. 7-15
Issue: B
10/8/07
Page 22 of 29 pages
. (Fig. 7-15)
TOYOTA
LAND CRUISER
2008 -
Procedure
TVIP V4
REMOTE ENGINE STARTER (RES)
(cc) Close the Hood. (Fig. 7-16)
EXAMPLE
(dd) The Hazard Lights flash twice. Registration
completed (Fig. 7-16)
If you fail this procedure, the hazard lights flash
3 times. Registration will not set.
Start again from Step a.
Fig. 7-16
V4 Diagnostic 1P Connectors
(ee) Disconnect the V4 Harness'1P RES
Diagnostic Connectors. (Fig. 7-17)
(ff) Secure the V4 Harness and 1P Connectors
with Electrical Tape as shown. (Fig. 7-17)
Electrical
Tape
Fig. 7-17
(gg) Secure the V4 Harness to the Vehicle
Harness with the Electrical Tape as shown.
(Fig. 7-17)
(hh) Press the Power Button to the "OFF"
(Indicator Light off) position.
Issue: B
10/8/07
Page 23 of 29 pages
TOYOTA
LAND CRUISER
2008 -
Procedure
TVIP V4
REMOTE ENGINE STARTER (RES)
8. Tags and Label Installation.
● For US Vehicles use the English Labels and
discard the Spanish Labels.
● For Mexico Vehicles use the Mexico Labels,
and discard the English Labels.
(a) Remove 2 of the Remote Controls from
their protective bag. (Fig. 8-1)
(1) Use a utility knife, to cut a slit in each bag.
Utility Knife, Clear Tape
4 Button Key
3 Button Key
2mm
2mm
Key
Label
(b) Using VDC approved cleaner and Cleaning
Method, clean the area indicated on the
Remote Controls. (Fig. 8-1)
(c) Attach the Key Label to the Remote
Controls as shown. (Fig. 8-1)
Key
Label
(1) Use a piece of the clean adhesive tape to lift the
labels off their protective backing.
Fig. 8-1
CAUTION: Do not touch the adhesive surface.
(d) Attach the Remote Engine Starter Tags to
the Vehicle Remote Controls. (Fig. 8-2)
Key Tag
Fig. 8-2
Clear Tape
Battery
Warning Label
------------------- ---------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
5mm
------------------- ---------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
5mm
Fig. 8-3
Issue: B
10/8/07
(e) Using VDC approved cleaner and Cleaning
Method, clean the area indicated on the
Engine Compartment Cover.(Fig. 8-3)
(f) Attach the Warning Label to the Engine
Compartment Cover as shown. (Fig. 8-3)
CAUTION: Do not touch the adhesive surface.
Page 24 of 29 pages
TOYOTA
LAND CRUISER
2008 -
Procedure
TVIP V4
REMOTE ENGINE STARTER (RES)
(g) Using Household Windex, clean the inside
of the Front Door Windows. (Fig. 6-1)
Clear Tape
10mm
V4 Window Label
(h) Place the Warning Labels on the inside of
the Front Door Windows as shown.
(Fig. 6-1)
Align to bottom
of Etching
(1) Use a piece of clean adhesive tape to lift the
Labels off their protective backing.
CAUTION: Do not touch the Adhesive
Surface.
Fig. 6-1
Clear Tape
Line up the labels properly. Do not attempt
to reposition the Labels once they are
placed.
1-5mm
V4 Window Label
NOTE: If Labels are being installed with other
Window Labels align them as shown in Fig. 6-2.
Align to bottom
of Other Labels
Other Label
(i) Place the V4 Owner's Guide, sealed in the
bag, in the Glove Box.
Fig. 6-2
Issue: B
10/8/07
Page 25 of 29 pages
TOYOTA
LAND CRUISER
2008 -
Procedure
TVIP V4
REMOTE ENGINE STARTER (RES)
Utility Knife
Large Foam Tape
Glove Box (backside)
9. Completing the Installation.
(a) Cut and apply ⅓ piece of Large Foam Tape
to the backside of the Glove Box as shown.
(Fig. 9-1)
⅓Foam Tape
(b) Complete the reassembly of the Vehicle.
(1) Verify the Panels fit together properly, with no
uneven gaps.
Fig. 9-1
Torque Wrench
Negative Battery
Cable
(c) Position the Negative Battery Cable at the
original factory position. (Fig. 9-2)
(1) Tighten the Nut to 36 in•lbf (4.07 N•m)
CAUTION: Do not touch the positive terminal.
(d) Clean up and remove any Trash.
Fig. 9-2
Battery
(e) Sealed in its protective Bag, place the
Owner’s Guide in the Glove Box.
(f) Reset the power windows.
(1) Press the Power Button to select the Ignition
“ON” position.
(2) Push down on the Power Window Switches
lowering the windows halfway.
(3) Pull up on the switches until the windows close
(4) Continue holding up on the Switches for a
minimum of 1 second.
Issue: B
10/8/07
Page 26 of 29 pages
TOYOTA
LAND CRUISER
2008 -
Checklist - these points MUST be checked to ensure a quality installation.
TVIP V4)
REMOTE ENGINE STARTER (RES)
Accessory Function Checks
Close the hood, place the shift lever in the “P” (parking) position, set the parking brake, close all doors,
and exit the vehicle.
Press the remote control’s lock button twice
within 2 seconds, then press and hold the lock
button 3 seconds.
The hazard lights flash after 3 seconds.
The engine starts.
The hazard lights flash repeatedly for 20
seconds.
Press the remote control’s unlock button.
The engine stops.
The hazard lights flash twice.
3
Start the Vehicle again using the remote. With
the engine running, press and hold the remote
control’s lock button 2 seconds.
Refer to Step 1.
The engine stops.
The hazard lights flash once.
4
Start the Vehicle again using the remote. With
the engine running and the smart key in your
possession, open any door.
Refer to Step 1.
The engine stops.
The hazard lights flash once.
1
2
Enter the vehicle and close all doors.
Start the Vehicle again using the remote. With
the engine running, manually unlock any door
with the inside lock switch.
Refer to Step 1.
The engine stops.
The hazard lights flash once.
The security alarm triggers. (if equipped)
Start the Vehicle again using the remote. With
the engine running, push on the foot brake.
Refer to Step 1.
The engine stops.
The hazard lights flash once.
7
Start the Vehicle again using the remote. With
the engine running, press the ignition button
on the dash.
Refer to Step 1.
The engine stops.
The hazard lights flash once
8
Move the shift lever out of “P” (Park).
Attempt to start the Vehicle using the remote.
The engine does not start.
Start the Vehicle again using the remote. With
the engine running, pull the hood release
handle.
Refer to Step 1.
The engine stops.
The hazard lights flash once.
The security alarm triggers. (if equipped)
5
6
9
Issue: B
10/8/07
Page 27 of 29 pages
TOYOTA
LAND CRUISER
2008 -
Checklist - these points MUST be checked to ensure a quality installation.
TVIP V4)
REMOTE ENGINE STARTER (RES)
Vehicle Function Check
Function
Function
□
Head Light
□
ABS Light (if equipped)
If the warning light remains on, it may indicate a
system malfunction.
□
□
□
□
□
□
□
□
□
□
□
□
□
High Beams
Rear Wiper/Washer (if equipped)
Daytime Running Lights
(if equipped)
□
□
□
□
□
□
□
□
□
□
□
□
□
□
Trunk/Tailgate/Bed Lights
(if equipped)
□
Navigation System (if equipped)
□
□
□
Glove Box Light (if equipped)
□
□
□
Rear Sunshade (if equipped)
Issue: B
Turn Signal Lights
Tail Lights
Stop Lights
Backup Lights
Hazard Lights
Marker Lights
Dome/Courtesy Lights
Panel/Switch Illumination
Accessory Controls/Illumination
(if equipped)
Key Sensor Buzzer
Fog Lights (if equipped)
Cruise Control Light (if equipped)
Seat Belt Warning Light
If the warning light remains on, it may
indicate a system malfunction.
10/8/07
Page 28 of 29 pages
Clock (if equipped)
Accessory Power Socket (if equipped)
Starter
Audio/Video (if equipped)
Power Sliding Door (if equipped)
Convenience Memory Settings (if equipped)
Heated Seats (if equipped)
Massage Seats (if equipped)
Rear Window Defogger (if equipped)
Power Side Mirrors (if equipped)
Side Mirror Defogger (if equipped)
Front Windshield Defogger (if equipped)
Steering Wheel Audio Control (if equipped)
Steering Wheel Column Adjusts Without
Interference
TOYOTA
LAND CRUISER
2008 -
Checklist - these points MUST be checked to ensure a quality installation.
Function
TVIP V4)
REMOTE ENGINE STARTER (RES)
Function
□
Air Bag Warning Light
If the warning light remains on, it may
indicate a system malfunction.
□
Lamp Failure Sensor
If the warning light remains on, it may indicate a
system malfunction.
□
Track/Skid Control Light
(if equipped)
If the warning light remains on, it
may indicate a system malfunction.
□
Front Wiper/Washer
□
□
□
□
□
□
HVAC
□
□
□
Hood Latch Release
Power Locks (if equipped)
Power Windows (if equipped)
Passenger Air Bag Switch (if equipped)
Rollover Side Curtain Air Bag Switch (RSCA) (if
equipped)
Power Seats (if equipped)
Horn
Gauges
Remove the short pin after Function check.
Check with your Port/Dealer to see if this step is necessary.
Store Short Pin Here
Issue: B
10/8/07
Page 29 of 29 pages
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement