Sony CMT-NEZ50, CMT-NEZ33 Operating instructions

Sony CMT-NEZ50, CMT-NEZ33 Operating instructions
2-663-704-14(1)
Notice for the customers in the
U.S.A.
this equipment does cause harmful interference to radio
or television reception, which can be determined by
turning the equipment off and on, the user is encouraged
to try to correct the interference by one or more of the
following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and
receiver.
– Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
– Consult the dealer or an experienced radio/TV
technician for help.
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received,
including interference that may cause undesired
operation.
Micro HI-FI
Component System
Operating Instructions
GB
Owner’s Record
The model and serial numbers are located on the rear of the unit. Record these numbers in the space
provided below. Refer to them whenever you call upon your Sony dealer regarding this product.
Model No. ______________ Serial No. ______________
CMT-NEZ50/NEZ33/
NEZ30
© 2006 Sony Corporation
This symbol is intended to alert the
user to the presence of uninsulated
“dangerous voltage” within the
product’s enclosure that may be of
sufficient magnitude to constitute a risk
of electric shock to persons.
Disposal of Old Electrical & Electronic
Equipment
(Applicable in the European Union
and other European countries with
separate collection systems)
WARNING
This appliance is
classified as a CLASS
1 LASER product. This
marking is located on the
rear exterior.
To reduce the risk of fire or electric
shock, do not expose this apparatus to
rain or moisture.
To reduce the risk of fire, do not cover the ventilation of
the apparatus with newspapers, tablecloths, curtains, etc.
And do not place lighted candles on the apparatus.
European model only
Excessive sound pressure from earphones and
headphones can cause hearing loss.
To reduce the risk of fire or electric shock, do not
place objects filled with liquids, such as vases, on the
apparatus.
Notice for customers: the
following information is only
applicable to equipment sold in
countries applying EU Directives
Connect the unit to an easily accessible AC outlet.
Should you notice an abnormality in the unit, disconnect
the main plug from the AC outlet immediately.
Do not install the appliance in a confined space, such as
a bookcase or built-in cabinet.
Do not expose the battery to excessive heat such as direct
sunlight, fire or the like.
CAUTION
The use of optical instruments with this product will
increase eye hazard.
According to the EU Directive related to product safety,
EMC and R&TTE, the manufacturer of this product
is Sony Corporation, 1-7-1 Konan, Minato-ku, Tokyo,
Japan.
The Authorized Representative is Sony Deutschland
GmbH, Hedelfinger Strasse 61, 70327 Stuttgart,
Germany.
For any service or guarantee matters please refer to
the addresses given in separate service or guarantee
documents.
This reminder is provided to call the CATV system
installer’s attention to Article 820-40 of the NEC
that provides guidelines for proper grounding and,
in particular, specifies that the cable ground shall be
connected to the grounding system of the building, as
close to the point of cable entry as practical.
The following FCC statement
applies only to the version of
this model manufactured for sale
in the U.S.A. Other versions may
not comply with FCC technical
regulations.
WARNING
This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant
to Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful
interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio
communications. However, there is no guarantee that
interference will not occur in a particular installation. If
Selecting a music source
Press the following buttons (or press FUNCTION 
repeatedly).
CD
CD  on the remote.
Tuner
TUNER/BAND .
Listening to the radio
Tape
TAPE  on the remote.
1 Select “FM” or “AM.”
Component (connected
using an audio cord)
FUNCTION  repeatedly
until “AUDIO IN” appears.
To
Press
Set the sound effect
Playing a CD/MP3 disc
1 Select the CD function.
Press CD  on the remote.
2 Place a disc.
Press  PUSH OPEN/CLOSE  on the unit,
and place a disc with the label side up on the CD
compartment.
To close the CD compartment, press  PUSH OPEN/
CLOSE  on the unit.
*Except for the North American model
 PUSH OPEN/CLOSE
Before using the system
To use the remote
Slide and remove the battery compartment lid , and
insert the two supplied R6 (size AA) batteries,  side
first, matching the polarities shown below.
Solid (Black/)
To
Press
Pause playback
 (pause)  on the remote (or
CD/ (play/pause)  on the
unit). To resume play, press the
button again.
For models with a voltage selector, set VOLTAGE SELECTOR
to the local power line voltage.
or
Notes on using the remote
• With normal use, the batteries should last for about six months.
• Do not mix an old battery with a new one or mix different types of
batteries.
• If you do not use the remote for a long period of time, remove the
batteries to avoid damage from battery leakage and corrosion.
Press  (power) .
AM loop antenna
/ (go back/go forward)
.
To reduce static noise on a weak FM stereo
station
Press FM MODE  on the remote repeatedly until
“STEREO” disappears to turn off stereo reception.
Playing a tape
1 Select the tape function.
2 Select the clock set mode.
Press CLOCK/TIMER SET  on the remote. If the
current mode appears on the display, press /
 on the remote repeatedly to select “CLOCK” and
then press ENTER  on the remote.
3 Set the time.
Press /  on the remote repeatedly to set
the hour, and then press ENTER  on the remote.
Use the same procedure to set the minute.
The clock settings are lost when you disconnect the
power cord or if a power failure occurs.
3 Start playback.
Press  (play)  on the remote (or TAPE/
(play/pause)  on the unit).
To
Press
Pause playback
 (pause)  on the remote (or
TAPE/ (play/pause)  on the
unit). To resume play, press the
button again.
Stop playback
 (stop) .
Rewind or fast
forward
/ (rewind/fast forward) .
Find a point in a
track or file
Hold down / (rewind/fast
forward)  during playback,
and release the button at the
desired point.
Changing the display
Select Repeat Play
REPEAT  on the remote
repeatedly until “REPEAT” or
“REPEAT 1” appears.
To change
Press
Information on
the display*
DISPLAY  on the remote
repeatedly when the system is on.
Display mode
(See below.)
DISPLAY  on the remote
repeatedly when the system is off.
Notes on Repeat Play
1 Turn on the system.
Wall socket
+/– (select folder) .
operation as normal (SHUF) Play.
To set the clock
White side for North
American model
If “TUNED” does not appear and the scanning does
not stop, press TUNING MODE  repeatedly until
“AUTO” and “PRESET” disappear, and then press
+/– on the remote (or TUNING +/– on the unit) 
repeatedly to tune in the desired station.
 (stop) .
Press PLAY MODE  repeatedly while the player is
stopped. You can select normal play (“ ” for all MP3
files in the folder on the disc), shuffle play (“SHUF” or
“
SHUF*”), or program play (“PGM”).
* When playing a CD-DA disc,
(SHUF) Play performs the same
Power
FM lead antenna
(Extend it horizontally.)
To tune in a station with a weak signal
Press PUSH OPEN/CLOSE   on the unit, and
insert the TYPE I (normal) tape into the cassette
holder with the side you want to play facing forward.
Make sure there is no slack in the tape to avoid
damaging the tape or the tape deck. Press PUSH
OPEN/CLOSE   on the unit again to close the
cassette holder.
To change the play mode
Right speaker
Connect the power cord to a wall socket.
If the plug does not fit the wall socket, detach the supplied
plug adaptor (only for models equipped with an adaptor).
Press  (stop) .
Press TAPE  on the remote.
Select a folder on an
MP3 disc
Select a track or file
Find a location and an orientation that provide
good reception, and then set up the antenna.
Keep the antennas away from the speaker cords
and the power cord to avoid picking up noise.
To stop automatic scanning
2 Insert a tape.
Stop playback
Brown side for
other regions
EQ  on the remote
repeatedly to select “BASS”
or “TREBLE,” and then
press / 
repeatedly to adjust the level.
Press  (play)  on the remote (or CD/ (play/
pause)  on the unit).
Antennas
Press +/– on the remote (or TUNING +/– on the unit)
. Scanning stops automatically when a station is
tuned in, and then “TUNED” and “STEREO” (for
stereo programs) appear. When you tune in a station
that provides RDS services, the station name appears
on the display (European model only).
Generate a more dynamic DSGX  on the unit.
sound (Dynamic Sound
Generator X-tra)
3 Start playback.
Insert only the stripped portion of the cord.
3 Tune in the desired station.
To add a sound effect
Hooking up the system securely
Speakers
2 Select the tuning mode.
Press VOLUME +/– on the remote (or turn the
VOLUME control on the unit) .
MPEG Layer-3 audio coding technology and patents
licensed from Fraunhofer IIS and Thomson.
Left speaker
Press TUNER/BAND  repeatedly.
To adjust the volume
CMT-NEZ33/NEZ30
• All tracks or files on a disc are played repeatedly up to five times.
• “REPEAT 1” indicates that a single track or file is repeated until you
stop it.
Notes on playing MP3 discs
• Do not save other types of files or unnecessary folders on a disc that
has MP3 files.
• Folders that have no MP3 files are skipped.
• MP3 files are played back in the order that they are recorded onto
the disc.
• The system can only play MP3 files that have a file extension of
“.MP3.”
• If there are files on the disc that have the “.MP3” file extension,
but that are not MP3 files, the unit may produce noise or may
malfunction.
• The maximum number of:
– folders is 150 (including the root folder).
– MP3 files is 255.
– MP3 files and folders that can be contained on a single disc is 256.
– folder levels (the tree structure of files) is 8.
• Compatibility with all MP3 encoding/writing software, recording
device, and recording media cannot be guaranteed. Incompatible
MP3 discs may produce noise or interrupted audio or may not play
at all.
Using optional audio
components
To connect an optional headphones
Press
U.S.A., Canadian and Australian
models only
Solid (Red/)
• If the disc begins with a CD-DA (or MP3) session, it is recognized
as a CD-DA (or MP3) disc, and playback continues until another
session is encountered.
• A disc with a mixed CD format is recognized as a CD-DA (audio)
disc.
To select
Adjusting the sound
This symbol on the product or on its packaging indicates
that this product shall not be treated as household
waste. Instead it shall be handed over to the applicable
collection point for the recycling of electrical and
electronic equipment. By ensuring this product is
disposed of correctly, you will help prevent potential
negative consequences for the environment and human
health, which could otherwise be caused by inappropriate
waste handling of this product. The recycling of
materials will help to conserve natural resources. For
more detailed information about recycling of this
product, please contact your local Civic Office, your
household waste disposal service or the shop where you
purchased the product.
Applicable accessories: Remote commander
ENERGY STAR® is a U.S. registered
mark. As an ENERGY STAR® partner,
Sony Corporation has determined that
this product meets the ENERGY STAR®
guidelines for energy efficiency.
Notes on playing multisession discs
Press TUNING MODE  repeatedly until “AUTO”
appears.
You are cautioned that any changes or modifications
not expressly approved in this manual could void your
authority to operate this equipment.
Note to CATV system installer:
Except for customers in the
U.S.A. and Canada
CMT-NEZ50
CAUTION
This symbol is intended to alert the
user to the presence of important
operating and maintenance (servicing)
instructions in the literature
accompanying the appliance.
Printed in China
Basic Operations
* For example, you can view CD/MP3 disc information, such as the
track or file number or folder name during normal play, or the total
play time while the player is stopped.
The system offers the following display modes.
Display mode
When the system is off,1)
Clock
Power Saving
Mode2)
The clock is displayed.
The display is turned off to conserve
power. The timer and clock continue
to operate.
1)
2)
The STANDBY indicator lights up when the system is off.
When the system is in Power Saving Mode, the following functions
are unavailable:
– setting the clock.
– changing the AM tuning interval
– changing the CD power manage function
Notes on the display information
• The following are not displayed;
– total playing time for a CD-DA disc depending on the play mode.
– total playing time for an MP3 disc.
– remaining playing time for an MP3 file.
• The following are not displayed correctly;
– elapsed playing time of an MP3 file encoded using a VBR
(variable bit rate).
– folder and file names that do not follow either the ISO9660 Level
1, Level 2 or Joliet in the expansion format.
• The following are displayed;
– ID3 tag information for MP3 files when ID3 version 1 and version
2 tags are used.
– up to 30 characters of ID3 tag information using uppercase letters
(A to Z), numbers (0 to 9), and symbols (" $ % ’ ( ) * + , – . / < =
> @ [ \ ] _ ` { | }).
Connect headphones to the PHONES jack  on the
unit.
To connect an optional component
Connect additional audio component to the AUDIO
IN jack  on the unit using an audio analog cord (not
supplied). Turn down the volume on the system, and then
press FUNCTION  repeatedly to select the AUDIO IN
function.
Troubleshooting
Other Operations
Creating your own CD program
Recording onto a tape
(Program Play)
You can record on a TYPE I (normal) tape in two ways:
Use buttons on the remote to create your own program.
CD Synchro Recording:
1 Press CD  to select the CD function.
2 Press PLAY MODE  repeatedly until “PGM”
appears while the player is stopped.
3 Press /  repeatedly until the desired
track number appears.
When programming MP3 files, press
+/– (select
folder)  repeatedly to select the desired folder, and
then select the desired file.
Selected track or file number
Total playing time of program
(including selected track or file)
4
Press ENTER  to add the track or file to the
program.
“– –.– –” appears when the total time exceeds 100
minutes for a CD, or when you select an MP3 file.
5 Repeat steps 3 through 4 to program additional
tracks or files, up to a total of 25 tracks or files.
6 To play your program of tracks or files, press 
(play) .
The program remains available until you open the CD
compartment. To play the same program again, select
the CD function, and press  (play) .
You can record an entire CD onto a tape.
Manual Recording:
You can record just the portions you like from a sound
source, including connected audio components.
Use buttons on the unit to control tape recording.
1 Load a recordable tape with the side you want to
record facing forward.
2 Prepare the recording source.
Press PLAY MODE  repeatedly until both “PGM” and
“SHUF” disappear while the player is stopped.
To delete the last track or file of the program
Press CLEAR  while the player is stopped.
To view program information, such as total
track number of the program
Press DISPLAY  repeatedly.
Presetting radio stations
You can preset your favorite radio stations and tune
them in instantly by selecting the corresponding preset
number.
Use buttons on the remote to preset stations.
1 Tune in the desired station (see “Listening to the
radio”).
Preset number
preset number.
If another station is already assigned to the selected
preset number, the station is replaced by the new
stations.
4 Press ENTER .
5 Repeat steps 1 through 4 to store other stations.
You can preset up to 20 FM and 10 AM stations. The
preset stations are retained for about half a day even
if you disconnect the power cord or if a power failure
occurs.
6 To call up a preset radio station, press TUNING
MODE  repeatedly until “PRESET” appears,
and then press +/–  repeatedly to select the
desired preset number.
7 Press  (power)  to turn off the system.
The system turns on 15 seconds before the preset
time. If the system is on at the preset time, the Play
Timer and the Rec Timer will not play or record.
To activate or check the timer again
For Manual Recording:
Select the desired source to record.
• The Play Timer setting remains as long as the setting is not canceled
manually.
• The volume is reduced to minimum during the Rec Timer.
• The Rec Timer is canceled automatically after the Rec Timer has
been activated.
3 Set the tape deck to stand by for recording.
For CD Synchro Recording:
Press CD SYNC .
For Manual Recording:
Press  PAUSE/START .
4 Start recording.
For CD Synchro Recording:
Press  PAUSE/START . When the recording
is completed, the CD player and the tape deck stop
automatically. If you are recording onto a tape and
the tape reaches the end of the front side part-way
through a track or file, “TURN TAPE” appears. Turn
the tape over to the reverse side, re-insert it, and
“PUSH REC” appears. And then press  PAUSE/
START .
For Manual Recording:
Press  PAUSE/START , and then start playing
the desired recording source.
If there is noise while recording from the tuner,
reposition the appropriate antenna to reduce the noise.
To stop recording
To cancel the timer
Repeat the same procedure as above until “OFF”
appears, and then press ENTER .
To change the setting
Start over from step 1.
Tips
1 Make sure the power cord and speaker cords are
correctly and firmly connected.
2 Find your problem in the checklist below, and
take the indicated corrective action.
If the issue persists, contact your nearest Sony dealer.
If the STANDBY indicator flashes
Immediately unplug the power cord, and check the
following item.
• If your system has a voltage selector, is the voltage
selector set to the correct voltage?
• Are the + and – speaker cords short-circuited?
• Are you using only the supplied speakers?
• Is anything blocking the ventilation holes on the
back of the system?
After the STANDBY indicator  stops flashing,
reconnect the power cord, and turn on the system. If
the issue persists, contact your nearest Sony dealer.
General
Sound comes from one channel, or the left
and right volumes are unbalanced.
• Place the speakers as symmetrically as possible.
• Connect only the supplied speakers.
COMPLETE : The preset operation ended normally.
FULL : You tried to program more than 26 tracks or files
(steps).
NO DISC : There is no disc in the player, or you have
loaded a disc that cannot be played.
NO STEP : All of the programed tracks have been
erased.
NO TAB : You cannot record because the overwrite
protection tab has been removed from the cassette.
NO TAPE : There is no tape in the tape deck.
NOT USED : You pressed an invalid button.
OVER : You have reached the end of the disc while
pressing  (fast forward)  during playback or
pause.
PUSH SELECT : You tried to set the clock or timer
during timer operation.
PUSH STOP : You pressed PLAY MODE  during
playback.
SET CLOCK : You tried to select the timer when the
clock is not set.
SET TIMER : You tried to select the timer when the
Play Timer or Rec Timer is not set.
TIME NG : The Play Timer or Rec Timer start and end
times are set to the same time.
Display examples
Display
indicates
Rec Timer:
You can record a preset radio station at a specified time.
Use buttons on the remote to control the Play Timer and
the Rec Timer. Make sure you have set the clock.
1 Prepare the sound source.
For Play Timer:
Prepare the sound source, and then press VOLUME
+/–  to adjust the volume.
To start from a specific CD track or MP3 file, create
your own CD program.
For Rec Timer:
Tune in the preset radio station.
2 Press CLOCK/TIMER SET .
3 Press /  repeatedly to select “PLAY
SET” or “REC SET” then press ENTER .
“ON TIME” appears, and the hour indication flashes.
4 Set the time to start playing or recording.
Press /  repeatedly to set the hour,
and then press ENTER .
The minute indication flashes. Use the procedure
above to set the minute.
5 Use the same procedure as in step 4 to set the
time to stop playing or recording.
• Do not place the system in an inclined position or in
locations that are extremely hot, cold, dusty, dirty, or
humid or lacking adequate ventilation, or subject to
vibration, direct sunlight or a bright light.
• Be careful when placing the unit or speakers on
surfaces that have been specially treated (for example,
with wax, oil, polish) as staining or discoloration of the
surface may result.
• If the system is brought directly from a cold to a warm
location or is placed in a very damp room, moisture
may condense on the lens inside the CD player, and
cause the system to malfunction. In this situation,
remove the disc, and leave the system turned on for
about a few hours until the moisture evaporates.
0 (zero)
• Remove any obstacles between the remote and the
remote sensor  on the unit, and position the unit
away from fluorescent lights.
• Point the remote at the system’s sensor.
• Move the remote closer to the system.
A
On heat buildup
B
H
• Heat buildup on the unit during operation is normal and
is not cause for alarm.
• Do not touch the cabinet if it has been used
continuously at a high volume because the cabinet may
have become hot.
• Do not obstruct the ventilation holes.
K
On the speaker system
M
R
This speaker system is not magnetically shielded, and
the picture on nearby TV sets may become magnetically
distorted. In this situation, turn off the TV, wait 15 to 30
minutes, and turn it back on.
If there is no improvement, move the speakers far away
from the TV.
S
Cleaning the cabinet
8 (eight)
D
G
CD/MP3 player
The sound skips, or the disc will not play.
• Wipe the disc clean, and replace it.
• Move the system to a location away from vibration (for
example, on top of a stable stand).
• Move the speakers away from the system, or place
them on separate stands. At high volume, speaker
vibration may cause the sound to skip.
O
Q
Play does not start from the first track.
• Return to Normal Play by pressing PLAY MODE 
repeatedly until both “PGM” and “SHUF” disappear.
Z
”
You can wake up to CD, tape or tuner at a preset time.
On placement
The remote does not function.
6 (six)
|
Play Timer:
• The unit is not disconnected from the AC power source
(mains) as long as it is connected to the wall socket,
even if the unit itself has been turned off.
• Completely disconnect the power cord (mains lead)
from the wall socket (mains) if it is not going to be
used for an extended period of time. When unplugging
the unit, always grip the plug. Never pull the cord
itself.
• Should any solid object or liquid get into the system,
unplug the system, and have it checked by qualified
personnel before operating it again.
• The AC power cord can be changed only by a qualified
service facility.
5 (five)
• The following discs take a longer time to start playback.
– a disc recorded with a complicated tree structure.
– a disc recorded in multisession mode.
– a disc that has not been finalized (a disc to which data
can be added).
– a disc that has many folders.
You can fall asleep to music. This function works even if
the clock is not set.
Press SLEEP  on the remote repeatedly. If you select
“AUTO,” the system automatically turns off after the
current disc or tape stops or in 100 minutes.
Do not select “AUTO” during Synchro Recording of a
tape.
On safety
• Move the system away from sources of noise.
• Connect the system to a different wall socket.
• Install a noise filter (available separately) to the power
cord.
Starting playback takes more time than usual.
Sleep Timer:
This product is designed to playback discs that
conform to the Compact Disc (CD) standard. Recently,
various music discs encoded with copyright protection
technologies are marketed by some record companies.
Please be aware that among those discs, there are some
that do not conform to the CD standard and may not be
playable by this product.
2 (two)
Note
Using the Timers
Music discs encoded with copyright
protection technologies
Severe hum or noise.
Press  (stop) .
The system offers three timer functions. You cannot
activate both the Play Timer and the Rec Timer at the
same time. If you use either with the Sleep Timer, the
Sleep Timer has priority.
3 Press +/–  repeatedly to select your desired
For Rec Timer:
Load a recordable tape. The display shows the timer
settings.
Press CLOCK/TIMER SELECT , press / 
repeatedly until “PLAY SEL” or “REC SEL” appears,
and then press ENTER .
Recording stops if you change to a different function.
2 Press TUNER MEMORY .
For Play Timer:
Press /  repeatedly until the desired
sound source appears, and then press ENTER . The
display shows the timer settings.
For CD Synchro Recording:
Press CD  on the remote to select the CD function.
Load the disc you want to record.
When recording a folder from an MP3 disc, press
PLAY MODE  repeatedly to select “ ” and then
press
+/– (select folder)  repeatedly to select
the desired folder.
To record only your favorite CD tracks in your desired
order, perform steps 2 through 5 of “Creating your
own CD program.”
While recording, you cannot listen to other sources.
To cancel Program Play
6 Select the sound source or prepare the tape.
Messages
The sound exhibits excessive wow or flutter
or dropout.
• Clean the capstans and pinch rollers. Also, clean and
demagnetize the tape heads. See “Precautions” for details.
To change the AM tuning interval
The AM tuning interval is factory-preset to 9 kHz (or 10
kHz, for some areas; this function is not available on the
European model).
Use buttons on the unit to change the AM tuning interval.
1 Tune in any AM station, and then turn off the
system.
2 While holding down TUNER/BAND , press
 (power) .
All the AM preset stations are erased. To reset the
interval to the factory preset, repeat the procedure.
You cannot change the AM tuning interval in Power
Saving Mode.
To reset the system to factory settings
If the system still does not operate properly, reset the
system to factory settings. You cannot reset the system to
factory settings in Power Saving Mode.
Use buttons on the unit to reset the unit to its factory
default settings.
1 Disconnect and reconnect the power cord, and
then turn on the system.
2 Press  (stop)  and  (power) , and turn
VOLUME control  to the left at the same time.
All user-configured settings, such as preset radio
stations, timer, and the clock, are deleted.
To prevent a tape from being accidentally
recorded over
%
Break off the cassette’s overwrite protection tab from
side A or B as illustrated.
.
Break off the
cassette tab
@
Severe hum or noise, or stations cannot be
received.
Tape deck
$
,
Tuner
• Connect the antenna properly.
• Find a location and an orientation that provide good
reception, and then set up the antenna again.
• Keep the antennas away from the speaker cords and the
power cord to avoid picking up noise.
• Connect a commercially available external antenna.
• Turn off nearby electrical equipment.
Clean this system with a soft cloth slightly moistened
with a mild detergent solution. Do not use any type
of abrasive pad, scouring powder, or solvent, such as
thinner, benzine, or alcohol.
Precautions
To later reuse the tape for recording, cover the broken tab
with adhesive tape.
Discs that this system CAN play
About a tape longer than 90 minutes
• Audio CD
• CD-R/CD-RW (audio data/MP3 files)
The use of the tape with more than 90 minutes of play
time is not recommended except for long, continuous
recording or playback.
Discs that this system CANNOT play
CD player section
System: Compact disc and digital audio system
Laser Diode Properties
Emission Duration: Continuous
Laser Output*: Less than 44.6µW
* This output is the value measurement at a distance of 200 mm from the
objective lens surface on the Optical Pick-up Block with 7mm aperture.
Tape deck section
Recording system: 4-track 2-channel, stereo
Tuner section
FM stereo, FM/AM superheterodyne tuner
FM tuner section:
Tuning range
North American model: 87.5 – 108.0 MHz (100 kHz step)
Other models: 87.5 – 108.0 MHz (50 kHz step)
Antenna: FM lead antenna
Antenna terminals: 75 ohms unbalanced
Intermediate frequency: 10.7 MHz
AM tuner section:
Tuning range
Pan-American model: 530 – 1,710 kHz (with 10 kHz tuning interval)
531 – 1,710 kHz (with 9 kHz tuning interval)
European model: 531 – 1,602 kHz (with 9 kHz tuning interval)
Other models: 530 – 1,710 kHz (with 10 kHz tuning interval)
531 – 1,602 kHz (with 9 kHz tuning interval)
Antenna: AM loop antenna, external antenna terminal
Intermediate frequency: 450 kHz
Speaker
CMT-NEZ50
Speaker system: 2-way, bass-reflex type
Speaker units
Woofer: 10 cm dia., cone type
Tweeter: 4 cm dia., cone type
Nominal impedance: 6 ohms
Dimensions (w/h/d): Approx. 145 × 235 × 175 mm
Mass: Approx. 1.9 kg net per speaker
CMT-NEZ33/NEZ30
Speaker system: Full Range Speaker System
Speaker units
North American model: 8 cm dia., cone type
Other models: 10 cm dia., cone type
Nominal impedance: 6 ohms
Dimensions (w/h/d): Approx. 145 × 235 × 155 mm
Mass:
North American model: Approx. 1.4 kg net per speaker
Other models: Approx. 1.5 kg net per speaker
General
Power requirements
North American model: AC 120 V, 60 Hz
Mexican model: AC 120 V, 60 Hz
European model: AC 230 V, 50/60 Hz
Australian model: AC 230 – 240 V, 50/60 Hz
Korean model: AC 220 V, 60 Hz
Taiwanese model: AC 120 V, 50/60 Hz
Argentine model: AC 220 V, 50/60 Hz
Other models: AC 120, 220 or 230 – 240 V, 50/60 Hz
Adjustable with voltage selector
Power consumption:
CMT-NEZ50
European model: 60 watts
0.5 watts (in Power Saving Mode)
Other models: 50 watts
CMT-NEZ33: 50 watts
CMT-NEZ30
North American model: 45 watts
Other models: 45 watts
Demagnetizing the tape heads
Supplied accessories: Remote Commander (1)/R6 (size AA) batteries (2)/AM
loop antenna (1)/FM lead antenna (1)
Notes on discs
Main unit
A DualDisc is a two sided disc product which mates
DVD recorded material on one side with digital
audio material on the other side. However, since the
audio material side does not conform to the Compact
Disc (CD) standard, playback on this product is not
guaranteed.
CMT-NEZ30
North-American model:
Continuous RMS power output (reference): 15 + 15 W (6 ohms at 1 kHz,
10% THD)
European model:
DIN power output (rated): 11 + 11 W (6 ohms at 1 kHz, DIN)
Continuous RMS power output (reference): 17 + 17 W (6 ohms at 1 kHz,
10% THD)
Music power output (reference): 28 + 28 W
The following are measured at AC 220 V, 50/60 Hz (Argentine model), AC
120 V, 60 Hz (Mexican model), AC 120, 220 or 230 – 240 V, 50/60 Hz (other
models)
DIN power output (rated): 11 + 11 W (6 ohms at 1 kHz, DIN)
Continuous RMS power output (reference): 15 + 15 W (6 ohms at 1 kHz,
10% THD)
Inputs
AUDIO IN: Sensitivity 250 mV, impedance 47 kilohms
Outputs
PHONES: Accepts headphones with an impedance of 8 ohms or more
SPEAKER: Accepts impedance of 6 to 16 ohms
Use dry- or wet-type cleaning cassette (available
separately) after every 10 hours of use, before you start
an important recording, or after playing an old tape.
Failure to clean the tape heads can cause degraded sound
quality or an inability of the unit to record or play tapes.
For details, refer to the instructions of the cleaning
cassette.
Cleaning the tape heads
Note on DualDiscs
CMT-NEZ33
The following are measured at AC 230 – 240 V, 50/60 Hz (Australian model),
AC 220 V, 60 Hz (Korean model), AC 120 V, 50/60 Hz (Taiwanese model),
AC 120, 220 or 230 – 240 V, 50/60 Hz (other models)
DIN power output (rated): 14 + 14 W (6 ohms at 1 kHz, DIN)
Continuous RMS power output (reference): 20 + 20 W (6 ohms at 1 kHz,
10% THD)
Inputs
AUDIO IN: Sensitivity 250 mV, impedance 47 kilohms
Outputs
PHONES: Accepts headphones with an impedance of 8 ohms or more
SPEAKER: Accepts impedance of 6 to 16 ohms
Dimensions (w/h/d) (excl. speakers):
CMT-NEZ50
Approx. 164 × 235 × 267 mm
CMT-NEZ33/NEZ30
Approx. 164 × 235 × 265 mm
Mass (excl. speakers):
CMT-NEZ50
Approx. 3.7 kg
CMT-NEZ33
Approx. 3.6 kg
CMT-NEZ30
North American model: Approx. 3.2 kg
European model: Approx. 3.6 kg
Other models: Approx. 3.3 kg
• CD-ROM
• CD-R/CD-RW other than those recorded in music CD
format or MP3 format conforming to ISO9660 Level
1/Level 2, Joliet or multisession
• CD-R/CD-RW recorded in multisession that have not
ended by “closing the session”
• CD-R/CD-RW of poor recording quality, CD-R/CDRW that have scratches or are dirty, or CD-R/CD-RW
recorded with an incompatible recording device
• CD-R/CD-RW which is finalized incorrectly
• Discs containing files other than MPEG 1 Audio Layer3 (MP3) files
• Discs of non-standard shape (for example, heart,
square, star)
• Some discs that have adhesive tape, paper, or sticker
attached to them
• Some rental or used discs with attached seals where the
glue extends beyond the seal
• Some discs that have labels printed using ink that feels
tacky when touched
• Before playing, wipe the disc with a cleaning cloth
from the center out to the edge.
• Do not clean discs with solvents, such as benzine
thinner, or commercially available cleaners or antistatic spray intended for vinyl LPs.
• Do not expose discs to direct sunlight or heat sources
such as hot air ducts, nor leave it in a car parked in
direct sunlight.
Inputs
AUDIO IN: Sensitivity 250 mV, impedance 47 kilohms
Outputs
PHONES: Accepts headphones with an impedance of 8 ohms or more
SPEAKER: Accepts impedance of 6 to 16 ohms
Use a demagnetizing cassette (available separately)
after every 20 to 30 hours of use. Failure to demagnetize
the tape heads can cause an increase in noise, a loss of
high frequency sound, and an inability to completely
erase tapes. For details, refer to the instructions of the
demagnetizing cassette.
Specifications
AUDIO POWER SPECIFICATIONS
POWER OUTPUT AND TOTAL HARMONIC DISTORTION:
(CMT-NEZ30 The United States model only)
With 6 ohm loads, both channels driven, from 120 – 10,000 Hz; rated 15 watts
per channel minimum RMS power, with no more than 10% total harmonic
distortion from 250 milliwatts to rated output.
Amplifier section
CMT-NEZ50
European model:
DIN power output (rated): 18 + 18 W (6 ohms at 1 kHz, DIN)
Continuous RMS power output (reference): 25 + 25 W (6 ohms at 1 kHz,
10% THD)
Music power output (reference): 38 + 38 W
The following are measured at AC 220 V, 50/60 Hz (Argentine model), AC
120 V, 60 Hz (Mexican model), AC 120, 220 or 230 – 240 V, 50/60 Hz (other
models)
DIN power output (rated): 14 + 14 W (6 ohms at 1 kHz, DIN)
Continuous RMS power output (reference): 20 + 20 W (6 ohms at 1 kHz,
10% THD)
Design and specifications are subject to change without notice.
• Standby power consumption: 0.5 W
• Halogenated flame retardants are not used in the
certain printed wiring boards.
• Lead-free solder is used for soldering certain parts.
• Halogenated flame retardants are not used in cabinets.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement