Whirlpool | KCGT 6010/I | Instruction for Use | KitchenAid KCGT 6010/I cooker hood

5019_718_02011_UK
30-05-2007
10:05
Pagina 1
KCGT 6010/I
Instructions for use
5019_718_02011_UK
30-05-2007
10:05
Pagina 2
5019_718_02011_UK
30-05-2007
10:05
Pagina 3
Warnings
4
Safeguarding the environment
5
Instructions for installation and use
6
Extraction modes
6
Installation
7
Hood description
9
Functioning
9
Maintenance
10
After-Sales Service
11
5019_718_02011_UK
30-05-2007
10:05
Pagina 4
Warnings
• This appliance should not be used by children or people with limited physical or mental
abilities and with no experience or knowledge of its use, unless they are supervised by
someone in charge of their safety or who has taught them how to use the appliance.
• Children should not play with the appliance.
1.
Do not connect the appliance to the mains supply until the installation is completely finished.
Before carrying out any cleaning or maintenance work, always disconnect the hood from the mains
supply by pulling out the plug or turning off the mains switch in the house.
2. Do not flambé food under the hood since the flames generated could cause a fire.
3. Do not leave a frying pan unattended when frying food as the cooking oil could catch fire.
4. Constant cleaning and maintenance of your hood will ensure it works properly. Regularly remove all the
ingrained food from dirty surfaces. Regularly remove and clean or change the filter. Do not use
inflammable material to convey exhaust air.
5. If the hood is used in conjunction with other appliances that run on gas or other fuels, the negative
pressure of the room should be no greater than 4Pa (4 x 10-5 bar). This is why you should make sure
the room is well aired.
6. Exhaust air from the hood should not be eliminated through the heating system chimney or appliances
that run on gas or other fuels.
7. The room should be sufficiently ventilated when the hood is used together with other appliances that
run on gas or other fuels.
8. Before touching the light bulbs, make sure they have cooled down.
Note: always use gloves when installing or carrying out maintenance work.
Electrical connection
The mains voltage should correspond with the voltage shown on the specifications label found inside the
hood. If there is no plug, connect the hood to a socket that complies with current legislation and is in an
easily accessible location. If there is no plug (direct connection to the mains supply) or the plug is not in an
easily accessible location, fit a legally complying bi-polar switch that ensures the complete disconnection of
the mains in the event of a category III line surge, in compliance with the installation regulations.
IMPORTANT: before reconnecting the hood circuit to the power supply, check that it is
working properly, that the mains cable has been properly fitted and that it has NOT been
crushed in its holder during installation.
Cleaning the hood
Warning! Failure to remove oil/grease (at least once a month) could lead to a fire breaking out. Use a soft
cloth and mild cleaning product. Never use harsh substances or alcohol.
Before using the hood
To get best performance from the hood, please read these user instructions carefully and keep them for
future reference.
Keep the packaging material (plastic bags, pieces of polystyrene, etc.) out of children’s reach as they can be
dangerous.
Make sure the hood has not been damaged during transportation.
The installation and the electrical connections, replacement of power cables with plug or flexible cable
should be carried out by a qualified technician in compliance with current legislation in force.
This appliance was designed to be used by adults.
4
5019_718_02011_UK
30-05-2007
10:05
Pagina 5
Warnings
Declaration of conformity
This product has been designed, manufactured and marketed according to the following:
- safety objectives of the “Low Voltage” Directive 2006/95/CE (wich replaces 73/23/CEE and subsequent
amendments).
- protection requirements of “EMC” Directive 89/336/EEC amended by Directive 93/68/EEC.
Troubleshooting guide
Hood does not work:
• Is the electrical power supply switched on?
• Is there a power failure?
Insufficient suction power:
• Did you set the right speed?
• Do the filters need to be cleaned or replaced?
• Are the air outlets blocked?
Light does not work:
• Does the bulb need to be replaced?
• Is the bulb correctly fitted?
Safeguarding the environment
1. Packing
The packaging material is entirely recyclable and marked with the recycling symbol
. Follow local
regulations for scrapping. Keep the packaging materials (plastic bags, polystyrene parts, etc.) out of reach
of children, as they are potentially dangerous.
2. Product
This appliance is marked according to the European Directive 2002/96/EC, Waste Electrical and Electronic
Equipment (WEEE).
By ensuring that this product is disposed of correctly, you will help prevent potentially negative
consequences for the environment and human health.
The symbol
on the product or on the documents accompanying the product indicates that this
appliance may not be treated as household waste. Instead, it should be handed over to the applicable
collection point for the recycling of electrical and electronic equipment.
Disposal must be carried out in accordance with local environmental regulations for waste disposal.
For more detailed information on treatment, recovery and recycling of this product, contact your local
authority, the household waste disposal service or the shop where you purchased the product.
5
5019_718_02011_UK
30-05-2007
10:06
Pagina 6
Instructions for installation and use
Follow the instructions in this manual carefully. All responsibility is denied for problems,
damage or fire to the appliance resulting in failure to comply with the instructions in this manual.
Extraction Modes
The hood is designed to be used in two
modes: Venting exhaust fumes to the
outside, or by passing the air through a
charcoal filter brfore recirculating the air
back into the kitchen.
Venting mode
The hood comes with an upper air outlet
B for the discharge of fumes to the
outside (venting pipe and fixing straps not
supplied). Fig. 1
Recirculation Mode
This mode is to be used when it is not
possible to vent the air to the outside.
Air is purified by passing through activated
charcoal filters (not provided) and
recirculated back out into the kitchen.
The air is sent back into the atmosphere
via a pipe that passes through the
cupboard cabinetry and is connected to
the connector ring. Fig. 2
Installation
The minimum distance between the
upper pan support surfaces on the
cooking appliance and the lowest part of
the cooker hood should be no less than
50 cm in the case of electrical cookers
and 70 cm in the case of gas or mixed
cookers. If the installation instructions for
the gas cooking appliance specify a
greater distance, then follow this
instruction.
6
5019_718_02011_UK
30-05-2007
10:06
Pagina 7
Installation
The hood comes with plugs suitable for most walls
/ ceilings. You should however consult a qualified
technician to make sure the installation is suitable
for your kind of wall/ceiling. The wall/roof should
be sufficiently strong to support the weight of the
hood.
is to be installed. Otherwise, protect the units
as much as possible and all the parts relating to
the installation. Choose a flat surface and cover
it with some protection where you can place
the hood and parts.
• Disconnect the hood by turning off the mains
switch in the house whilst connecting the
electrics.
• Furthermore, check that near the area where
you are installing the hood (in an area accessible
even when the hood is fitted) there is an
electric socket and that you can connect to an
extractor towards the outside (only in the
venting mode).
• Carry out all the building work necessary (e.g.:
installation of an electrical supply and/or hole to
pass the venting pipe through).
This kind of hood must be inserted into a
cupboard or cabinetry for support.
Before installation:
• Check that the product purchased is the right
size for the area where it is to be installed.
∑ To make installation easier, temporarily remove
the grease filters and other parts that can be
removed whose dismantling and assembly are
described here. These should be refitted when
installation is complete. See the relative
paragraph for dismantling.
• Remove the active carbon filter/s if provided
(again consult relative paragraph). This/these
should be re-assembled only if you wish to use
the hood in the recirculation mode.
• Check that there are no parts (e.g. bags with
screws, warranty) inside of the hood (for
transport reasons). If there are, remove them
and put to the side.
• If possible, disconnect and remove the
surrounding units and those near the installation
area of the hood so that you have better
accessibility to the ceiling / wall where the hood
Fig. 3
Cut a slot on the bottom of the cupboard
according to the measurements shown.
Cut another hole on the top of the cupboard for
the venting pipe and power lead.
All measurements in mm
7
5019_718_02011_UK
30-05-2007
10:06
Pagina 8
Installation
Fig.4
• Connect an extraction pipe to the connection
ring on the hood and, whilst you inserting the
hood into the cabinetry, check that the
extraction pipe and the electrical wire come out
of the hole made in the top of the cupboard.
• Attach the hood to the bottom of the cupboard
with 8 screws. The frame on the box has more
than 8 slots for passing the screws through, use
the most suitable ones for your installation
making them as equidistant as possible.
Fig. 5
• Remove the grease filter and hook the filter
support frame onto the hood. At this stage
connect up the electrics on the control panel
and the lights.
• Hook the filter support frame onto the hood
(snap fitting onto the two side seals).
• Refit the grease filter.
5.1
5.2
5.3
5.4
8
CLACK!
5019_718_02011_UK
30-05-2007
10:06
Pagina 9
Hood description
Fig. 6
1. Control panel
2. Grease filter
3. Handle for unhooking the grease filter
4. Halogen bulbs
Functioning
Turn to maximum speed when there is a lot of steam in the kitchen. We would advise you to turn the
suction on 5 minutes before starting to cook and leave it running after you have finished cooking for about
another 15 minutes.
1. ON/OFF light button: press to turn the light on or off.
2. Motor ON/OFF button: press to turn the hood on or off.
Once the hood is on, it sucks at the speed (power) of the previously selected suction.
3. Extraction speed button 1
4. Extraction speed button 2
5. Extraction speed button 3
6. Intense extraction ON/OFF speed button: lasts about 5 minutes, after which the hood returns to
previously selected extraction speed .
7. Timer ON/OFF button: pressing this button can limit the running duration of the extraction selected,
as follows:
Speed 1 for 20 minutes.
Speed 2 for 15 minutes.
Speed 3 for 10 minutes.
Intensive speed for 5 minutes.
After which the hood turns itself off.
If there are any running problems, before contacting the Customer Care Centre, disconnect the appliance
from the mains for at least 5 seconds by removing the plug, then reconnect again.
If the problem persists, contact the Customer care Centre.
9
5019_718_02011_UK
30-05-2007
10:06
Pagina 10
Maintenance
Always disconnect the power supply before carrying out any kind of maintenance work.
Cleaning
The hood should be cleaned regularly both inside and out (at least as often as you carry out maintenance
on the grease filters).
Use a damp cloth with mild cleaning products. Avoid using harsh products. DO NOT USE ALCOHOL!
Warning: Failure to follow the cleaning instructions on the hood and the replacement and
cleaning of the filters, could lead to a fire starting. Please, therefore, follow the instructions
given carefully.
Grease filter
It should be cleaned by hand once a month with
mild cleaning products, or in the dishwasher at a
low temperature and on the short cycle.
When washing in the dishwasher, the metallic
grease filter might discolour but its filtering abilities
remain unchanged.
In order to dismantle the grease filter, pull the
spring handle to unhook it. Fig. 7
Carbon filter (only in recirculation mode) Fig. 8
The Activated Carbon Filter absorbs the unpleasant
smells produced when cooking.
The saturation of the carbon filter varies depending
on the installation, usage and how often the grease
filters are cleaned.
In any case, the cartridge must be replaced at least
once every four months.
Fitting/dismantling the carbon filter:
- Remove the grease filter, unhook the filter
support frame taking care to disconnect the
control panel and lights (see Fig. 5).
- Attach a carbon filter on each side to cover
both the protection grills on the motor impeller,
then turn the central handle C on the filters
clockwise. Turn the central handle C on each
filter anticlockwise to dismantle.
- Refit the filter support frame, re-connecting the
control panel and lights and refitting the grease
filter.
Replacing the bulbs Fig. 9
Disconnect the appliance from the mains supply.
Warning! Before touching the light bulbs
make sure they have cooled down.
1. Remove the protective cover using a small flat
screwdriver or a similar tool.
2. Replace the blown bulb.
Only use 20W max (G4) halogen bulbs, and do
not touch them with your bare hands.
3. Fit the light cover on again (clicks into place).
If the light does not work, check that the bulb has
been inserted properly before calling the Customer
Care Centre.
10
5019_718_02011_UK
30-05-2007
10:06
Pagina 11
After-Sales Service
Before calling Customer Care Centre:
1. See if you can solve the problem yourself with
the help of the “Troubleshooting guide”.
2. Switch off the hood for a few minutes and restart it to see if the problem has cleared itself.
3. If the malfunction persists, call the Customer
Care Centre Service.
Specify:
• the nature of the problem,
• the product model on the rating plate inside the
hood and visible when you remove the grease
filters,
• your full address,
• your telephone number and area code,
• the service code (number below the word
SERVICE on the rating plate inside the hood
behind the grease filter).
If repair work has to be carried out, contact the
Customer Care Centre (this is a guarantee that
original spare parts will be used and a proper
repair job done).
Failure to comply with these instructions could
compromise the safety and quality of your
appliance.
11
5019_718_02011_UK
30-05-2007
10:06
Pagina 12
Electrical connection for Great Britain and Ireland only
Warning - this appliance must be earthed
Fuse replacement
If the mains lead of this appliance is fitted with a BS 1363A
13amp fused plug, to change a fuse in this type of plug use an
A.S.T.A. approved fuse to BS 1362 type and proceed as follows:
1. Remove the fuse cover (A) and fuse (B).
2. Fit replacement 13A fuse into fuse cover.
3. Refit both into plug.
Important:
The fuse cover must be refitted when changing a fuse and if the
fuse cover is lost the plug must not be used until a correct replacement is fitted.
Correct replacement are identified by the colour insert or the colour embossed in words on the base of
the plug.
Replacement fuse covers are available from your local electrical store.
For the Republic of Ireland only
The information given in respect of Great Britain will frequently apply, but a third type of plug and socket
is also used, the 2-pin, side earth type.
Socket outlet / plug (valid for both countries)
If the fitted plug is not suitable for your socket outlet, please contact KitchenAid Service for further
instruction. Please do not attempt to change plug yourself. This procedure needs to be carried out by a
qualified technician in compliance with the manufactures instructions and current standard safety
regulations.
12
5019_718_02011_UK
30-05-2007
10:06
Pagina 13
5019_718_02011_UK
30-05-2007
10:06
Pagina 14
5019_718_02011_UK
30-05-2007
10:06
Pagina 15
5019_718_02011_UK
30-05-2007
Printed in Italy
05/07
5019 718 02011
10:06
Pagina 16
n
GB
Download PDF

advertising