Toshiba SD-V57HTSU Owner's manual

Toshiba SD-V57HTSU Owner's manual
TH-C550M.NA1UTT
RH0074C
ENG
DIGITAL
V I D E 0
_
O=_=TALAUO=O
SURROUND
DVD/VCR
Home Theater System
S
Before connecting, operating or adjusting this product,
please read this instruction booklet carefully and completely.
©2005 Toshiba Corporation
This device does not tape-record
copy protected DVD Video Discs.
I
CAUTION: The apparatus should not be exposed to water
(dripping or splashing) and no objects filled with liquids, such
as vases, should be placed on the apparatus.
CAUTION
FCC WARNING: This equipment may generate or use radio
frequency energy. Changes or modifications to this
equipment may cause harmful interference unless the modifications are expressly approved in the instruction manual. The
user could lose the authority to operate this equipment if an
unauthorized change or modification is made.
CAUTION:
TO REDUCE THE RISK
OF ELECTRIC
SHOCK
DO NOT REMOVE COVER (OR BACK)
NO USER-SERVICEABLE
PARTS INSIDE
REFER SERVICING
TO QUALIFIED
SERVICE
PERSONNEL.
REGULATORY
This lightning flash with arrowhead symbol within an
equilateral triangle is intended to alert the user to
the presence of uninsulated dangerous voltage
within the product's enclosure that may be of
sufficient magnitude to constitute a risk of electric
shock to persons.
The exclamation point within an equilateral triangle
is intended to alert the user to the presence of
important operating and maintenance (servicing)
instructions in the literature accompanying the
product.
WARNING:
TO REDUCE THE RISK OF FIRE OR ELEC-
TRIC SHOCK, DO NOT EXPOSE THIS APPARATUS
RAIN OR MOISTURE.
TO
CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH
WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.
ATTENTION: POUR €:VITER LES CHOC €:LECTRIQUES,
INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHE
DANS LA BORNE CORRESPONDANTE
DE LA PRISE ET
POUSSER JUSQU'AU FOND.
WARNING: Do not install this equipment
such as a bookcase or similar unit.
in a confined space
NOTE TO CABLE/TV INSTALLER: This reminder is provided to
call the cable TV system installer's attention to Article 820-40 of
the National Electric Code (U.S.A.). The code provides guidelines
for proper grounding and, in particular, specifies that the cable
ground shall be connected to the grounding system of the
building, as close to the point of the cable entry as practical.
CAUTION:
This DVD/VCR receiver employs a Laser System.
To ensure proper use of this product, please read this owner's
manual carefully and retain for future reference. Should the
unit require maintenance, contact an authorized service
location.
Use of controls, adjustments, or the performance of procedures other than those specified herein may result in hazardous radiation exposure.
To prevent direct exposure to laser beam, do not try to open
the enclosure. Visible laser radiation when open. DO NOT
STARE INTO BEAM.
INFORMATION:
FCC Part 15
This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the product is
operated in a residential installation. This product generates,
uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction manual,
may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur
in a particular installation. If this product does cause harmful
interference to radio or television reception, which can be
determined by turning the product off and on, the user is
encouraged to try to correct the interference by one or more
of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the product and
receiver.
• Connect the product into an outlet on a circuit different
from that to which the receiver is connected.
• Consult the dealer or an experienced
for help.
SERIAL
radio/TV technician
NUMBER: The serial number is found on the back of
this unit. This number is unique to this unit and not available to
others. You should record requested information here and
retain this guide as a permanent record of your purchase.
Model No.
Serial No.
IMPORTANT
SAFETY
1. Read these instructions. - All these safety and operating instructions should be read before the product is
operated.
INSTRUCTIONS
11. Only use attachments/accessories
the manufacturer.
specified
by
2. Keep these instructions. - The safety, operating and
use instructions should be retained for future reference.
3. Heed all warnings. - All warnings on the product and
in the operating instructions should be adhered to.
4. Follow all instructions. - All operating
instructions should be followed.
and use
5. Do not use this product near water. - For example:
near a bath tub, wash bowl, kitchen sink, laundry tub,
in a wet basement; or near a swimming pool; and
other areas located near water.
6. Clean only with dry cloth. - Unplug this product from
the wall outlet before cleaning. Do not use liquid
cleaners.
7. Do not block any ventilation openings. Install in
accordance with the manufacturer's instructions. Slots and openings in the cabinet are provided for
ventilation and to ensure reliable operation of the
product and to protect it from over-heating. The
openings should never be blocked by placing the
product on a bed, sofa, rug or other similar surface.
This product should not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer's instructions
have been adhered to.
8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus
(including amplifiers) that produce heat.
g.
Do not defeat the safety purpose of the polarized
or grounding-type plug. A polarized plug has two
blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are
provided for your safety. If the provided plug does
not fit into your outlet, consult an electrician for
replacement of the obsolete outlet.
10. Protect the power cord from being walked on or
pinched
particularly
at plugs, convenience
receptacles, and the point where they exit from
the product.
12. Use only with the cart, stand, tripod, bracket, or
table specified by the manufacturer, or sold with
apparatus. When a cart is used, use caution
when moving the cart/product combination to
avoid injury from tip-over.
13. Unplug this product during lightning storms or
when unused for long periods of time.
14. Refer all servicing to qualified service personnel.
Servicing is required when the product has been
damaged in any way, such as power-supply cord
or plug is damaged, liquid has been spilled or
objects have fallen into the product, the product
has been exposed to rain or moisture, does not
operate normally, or has been dropped.
Introduction
Safety Precautions ............................
IMPORTANT SAFETY INSTRUCTIONS ............
Table of Contents .............................
Before Use ................................
Playable Discs .............................
Precautions ...............................
Notes on Discs .............................
About Symbols .............................
Selecting the Viewing Source ..................
Front Panel ..................................
Display Window ..............................
Remote Control ..............................
Rear Panel .................................
2
3
4
5-6
5
6
6
6
6
7
8
9
10
Preparation
Connections .............................
11-14
Connecting Antenna/Cable TV to a
DVDNCR Receiver ........................
11
Basic TV Connections ......................
12
Optional TV Connections ....................
12
Speaker System Connections .................
13
Speaker Positioning ........................
13
Radio Antenna Connections ..................
14
Accessory AudioNideo (A/V) Connections to
DVDNCR Receiver ........................
14
Digital Device Connections ...................
14
Selecting the Input/Output Source ..............
15
Before Operation - Sound Mode Descriptions .....
16
Mini Glossary for Audio Stream & Surround Mode . 16
Sound Mode .............................
16
Volume Control ...........................
16
Muting ..................................
16
VCR Operation Setup ......................
17-19
On-Screen Display(OSD) ....................
17
On-Screen Menus Setup ....................
17
VCR Setup Menu Options ...................
18
Channel Selection .........................
18
Setting the Clock ..........................
19
DVD Operation Setup ......................
20-23
General Explanation ........................
20
On-Screen Display .........................
20
Initial Settings ..........................
21-23
• General Operation ......................
21
• Language .............................
21
• Picture ...............................
21
Progressive Scan .......................
21
• Speaker Setup .........................
22
• Others ...............................
22
• Parental Control ........................
23
OcPRe
ration
Operation ...........................
Normal Playback ..........................
Special Effect Playbacks ....................
• Search ...............................
• Still Picture and Frame-by-Frame Playback
• Slow Motion ...........................
• Variable playback speed control ............
Normal Recording .........................
Timer Recording ........................
Instant Timer Recording .....................
Dubbing and Editing ........................
Copying from DVD to VCR ...................
VHS Hi-Fi Stereo System/MTS Broadcast .......
Tape Counter Memory Feature ................
Additional Information .......................
DVD and Video CD Operation ................
Playing DVD and Video CD ..................
General Features .......................
• Moving to another TITLE .................
• Moving to another CHAPTER/TRACK .......
24-29
24
24
24
... 24
24
24
25
25-26
27
27
27
28
29
29
30-32
30
30-32
30
30
• Slow Motion ...........................
30
• Still Picture and Frame-by-Frame Playback ... 30
• Search ...............................
31
• Random ..............................
31
• Repeat ...............................
31
• RepeatA-B ...........................
31
• 3D Surround ..........................
31
• Time Search ...........................
31
• Zoom ................................
31
• Marker Search .........................
32
• Changing Video Mode ...................
32
Special DVD Features ......................
32
• Checking the contents of
DVD Video discs: Menus .................
32
• Title Menu ............................
32
• Disc Menu ............................
32
• Camera Angle .........................
32
Changing the Audio Language .............
32
• Changing the Audio Channel ..............
32
• Subtitle ...............................
32
• Screen Saver ..........................
32
Audio CD and MP3/WMA Disc Operation .......
33-34
Playing an Audio CD and MP3/WMA Discs .......
33
Notes on MP3 Recordings ...................
33
• Pause ...............................
34
• Moving to another Tracks .................
34
• Search ...............................
34
• Random ..............................
34
• Repeat Track/All/Off ....................
34
• RepeatA-B ...........................
34
• 3D Surround ..........................
34
• Changing the Audio Channel ..............
34
JPEG File Operation .........................
35
Viewing JPEG Files on a Disc ................
35
• Selecting other Files .....................
35
• Still Picture ............................
35
• To flip the picture .......................
35
• To rotate picture ........................
35
Notes on JPEG Files .......................
35
Programmed Playback ........................
36
Programmed Playback with Audio CDs
and MP3/WMA Discs .......................
36
Programmed Playback with Video CD ..........
36
• Repeat Programmed Tracks ...............
36
• Erasing a Track from Program List ..........
36
• Erasing the whole Program List ............
36
Speaker Setup ..............................
37
Radio Operation ..........................
38-39
Presetting the Radio Stations .................
38
Listening to the Radio ......................
38
To Clear the Stored Radio Stations .............
38
Tuning into a Station Manually ................
39
For your reference .........................
39
Tuning into a Station Automatically .............
39
Labeling Stations ..........................
39
Reference
Controlling Your TV with the Supplied Remote
Troubleshooting ..........................
Language Code List ..........................
Area Code List ..............................
Specifications ............................
Limited United States Warranty .................
. 40-41
42-43
44
45
46-47
48
About the symbols for instructions
Z_
Indicates hazards likely to cause harm to the unit
itself or other material damage.
Note: Indicates special operating features of this unit.
Tip:
Indicates tips and hints for making the task easier.
Playable
Discs
v, D Eo
DVD
(8 cm/12 cm disc)
Video CD (VCD)
(8 cm / 12 cm disc)
............
AudioCD
(8 cm/12 cm disc)
In addition, this unit can play a DVD-R/+RW, SVCD and
CD-R or CD-RW that contains audio titles, MP3, WMA
or JPEG files.
Notes
• Depending on the conditions of the recording equipment or the CD-R/RW (or DVD-R/_+RW) disc itself,
some CD-R/RW (or DVD-R/+RW) discs cannot be
played on the unit.
• Do not attach any seal or label to either side (the
labeled side or the recorded side) of a disc.
• Do not use irregularly shaped CDs (e.g., heartshaped or octagonal). It may result in malfunctions.
Notes on DVDs and Video CDs
Because of problems and errors that can occur during
the creation of DVD and Video CD software and/or the
manufacture of DVD and Video CD discs, Toshiba cannot guarantee that this DVDNCR Receiver will play
every feature of every DVD bearing the DVD logo
and/or every Video CD bearing the CD logo. As one of
the creators of DVD technology, Toshiba DVD players
are manufactured using the highest standards of quality,
and as a result, such incompatibilities are rare. If you
happen to experience any difficulty playing a DVD or a
Video CD on this DVDNCR Receiver, please feel free
to call our Consumer Solution Center (see page 49).
Notes on copyright
The unauthorized recording, use, distribution, or revision of television programs, videotapes, DVDs and
other materials, is prohibited under the Copyright Laws
of the United States and other countries, and may subject you to civil and/or criminal liability.
This product incorporates copyright protection technology that is protected by method claims of certain U.S.
patents and other intellectual property rights owned by
Macrovision Corporation and other rights owners. Use
of this copyright protection technology must be authorized by Macrovision Corporation, and is intended for
home and other limited viewing uses only unless otherwise authorized by Macrovision Corporation. Reverse
engineering or disassembly is prohibited.
Regional code of the DVD/VCR Receiver and DVDs
This DVD/VCR Receiver is designed and manufactured for playback of region "1" encoded
DVD software. The region code on the labels of
some DVDs indicates which type of player can
play those discs. This unit can only play DVDs labelled
"1" or "ALL". If you try to play any other discs, the message "Check Regional Code" will appear on the TV
screen. Some DVDs that have no region code label
may still be subject to area restrictions and therefore
not playable.
Note on DTS-encoded CDs
When playing DTS-encoded CDs, excessive noise may
be exhibited from the analog stereo output. To avoid
possible damage to the audio system, turn down the
volume before playing back such discs, adjust the volume gradually, and keep the volume level low. To enjoy
DTS Digital Surround ® playback, an external 5.1 channel DTS Digital Surround ® decoder system must be connected to the digital output of the unit.
Disc-related Terms
Title (DVD only)
The main film content or accompanying feature content
or additional feature content, or music album.
Each title is assigned a title reference number enabling
you to locate it easily.
Chapter (DVD only)
Sections of a picture or a musical piece that are smaller
than titles. A title is composed of one or several chapters. Each chapter is assigned a chapter number,
enabling you to locate the chapter you want. Depending
on the disc, chapters may not be recorded.
Track (Video CD and Audio CD only)
Sections of a picture or a musical piece on a video CD
or an audio CD. Each track is assigned a track number,
enabling you to locate the track you want.
Scene
On a video CD with PBC (Playback control) functions,
moving pictures and still pictures are divided into sections called "Scenes". Each scene is displayed in the
menu screen and assigned a scene number, enabling
you to locate the scene you want.
A scene is composed of one or several tracks.
Types of Video
CDs
There are two types of Video CDs:
Video CDs equipped with PBC (Version 2.0)
PBC (Playback control) functions allow you to interact
with the system via menus, search functions, or other
typical computer-like operations. Moreover, still pictures
of high resolution can be played if they are included in
the disc.
Video CDs not equipped with PBC (Version 1.1)
Operated in the same way as audio CDs, these discs
allow playback of video pictures as well as sound, but
they are not equipped with PBC.
Precautions
Handling
the unit
When shipping the unit
The original shipping carton and packing materials
come in handy. For maximum protection, re-pack the
unit as it was originally packaged at the factory.
Cleaning
Fingerprints and dust on the disc can cause poor picture quality and sound distortion. Before playing, clean
the disc with a clean cloth. Wipe the disc from the center out.
When setting up the unit
The picture and sound of a nearby TV, VCR, or radio
may be distorted during playback. In this case, position
the unit away from the TV, VCR, or radio, or turn off the
unit after removing the disc.
To keep the surface clean
Do not use volatile liquids, such as insecticide spray,
near the unit. Do not leave rubber or plastic products in
contact with the unit for a long period of time. They will
leave marks on the surface.
Cleaning the unit
To clean the cabinet
Use a soft, dry cloth. If the surfaces are extremely dirty,
use a soft cloth lightly moistened with a mild detergent
solution. Do not use strong solvents such as alcohol,
benzine, or thinner, as these might damage the surface
of the unit.
To obtain a clear picture
The DVDNCR Receiver is a high-tech, precision
device. If the optical pick-up lens and disc drive parts
are dirty or worn, the picture quality will be poor.
Regular inspection and maintenance are recommended
after every 1,000 hours of use. (This depends on the
operating environment.)
For details, please contact your nearest dealer.
Moisture
Condensation
Never operate the DVDNCR Receiver immediately after
moving it from a cold location to a warm location. Leave
it for two or three hours without operating it. If you use
the DVDNCR Receiver in such a situation, it may damage discs/tapes and internal parts.
discs
YES
NO
_
Do not use strong solvents such as alcohol, benzine,
thinner, commercially available cleaners or anti-static
spray intended for older vinyl records.
About Symbols
About the ® symbol display
" (S) " may appear on the TV screen during operation.
This icon means the function explained in this owner's
manual is not available at that moment or with that specific DVD video disc.
About
the disc symbols
for instructions
A section whose title has one of the following symbols are
applicable only to those discs represented by the symbol.
DVDs.
Audio CDs.
Video CDs with the PBC (playback control)
function.
Video CDs without the PBC (playback control)
function.
MP3 Discs.
WMA Discs.
JPEG Files.
Notes
Handling
on Discs
discs
Do not touch the playback side of the disc.
Hold the disc by the edges so that fingerprints will not
get on the surface.
Do not stick paper or tape on the disc.
Storing
discs
After playing, store the disc in its case.
Do not expose the disc to direct sunlight or sources of
heat, or leave it in a parked car exposed to direct sunlight, as there may be a considerable temperature
increase inside the car.
Selecting
the Viewing Source
You must select one of your output sources (DVD or
VCR) to view on the TV screen.
• If you want to view DVD deck output source:
PressDVD/CD until DVD indicatorin the display window lights
and output source of DVD deck is viewed on the TV screen,
• If you want to view VCR deck output source:
PressVCR until VCR indicatorin the display window lights and
output source of VCR deck is viewed on the TVscreen,
• It you want to listen to AM/FM radio broadcasts:
PressFM/AM until RADIO indicatorin the displaywindow lights
and the frequency band appears on the TV screen.
Notes
• If you insert a disc while the DVD/VCR Receiver is in
the VCR mode, the DVDNCR Receiver will switch to
DVD mode automatically.
• If you insert a cassette tape without an erasure prevention tab intact while the DVDNCR Receiver is in
the DVD mode, the DVDNCR Receiver will switch to
VCR mode automatically.
I
I
ON/STANBY I/_
Switches the DVDNCR
_ EJECT
Ejects the tape in the VCR deck.
Receiver ON and OFF.
LINE IN 2 (VIDEO / AUDIO (L/R) input
Connect the audio/video output of an
external source (Audio system, TV/Monitor,
another VCR).
VOLUME
Adjusts volume of speakers.
_ (PLAY)
To play back a recorded
tape er disc.
Disc Tray (DVD deck)
Insert a disc here.
TUNING (/_ / _/)
Selects FM and AM band.
COPY/MEMORY
Press to copy a DVD in the DVD deck to a VHS tape
in the VCR deck.
Memorizes currently tuned Radio frequency (station).
A OPEN/CLOSE
Opens or closes the disc tray.
Cassette
RADIO
Selects Radio operation
mode.
CH/PRESET (/_/'_/)
Scans up or down through
memorized channels or radio
frequencies (stations).
Point the DVDNCR
Remote Sensor
Receiver remote
control here.
Display window
Shows the current status of the
DVDNCR Receiver.
Compartment
(VCR deck)
Insert a video cassette here.
DVDNCR
Toggles control between
the DVD deck and the
VCR deck.
OREC
To record normally or to activate
Instant Timer Recording.
II (PAUSE/STEP)
Pause playback or recording
temporarily/press repeatedly for
frame-by-frame playback.
• (STOP)
Stops playback of a disc or tape.
/_t_1
DVD: Go to beginning of current chapter/track or Press two times in quick successions to go
to previous chapter/track. Press and hold for a fast reverse search.
VCR: Rewinds the tape during the STOP mode or for fast reverse picture search.
DVD: Go to NEXT chapter/track. Press and hold for two seconds for a fast forward search.
VCR: Advances the tape during the STOP mode or for fast forward picture search.
m
I
I
I
I
A cassette is in the VCR deck.
Indicates encoding format of the current disc.
RADIO
Indicates RADIO mode is active
MUTE
The speaker sound is muted.
Indicates sound mode is
DOLBY PRO LOGIC or DOLBY PRO LOGIC II.
SAP Indicates when a SAP BILINGUAL
broadcast is being received.
HI-FI Indicates the unit is playing
back a tape recorded in Hi-Fi.
REC
DVD/VCR Receiver is Recording.
COPY
DVD to VCR copy
is in progress.
TIMER DVD/VCR
Receiver is in timer
recording or a timer
recording is programmed.
Lights when a disc
is in the DVD deck
PROG Indicates
when programmed
playback is in
progress.
Ir)DOIGiTAi._'i()DriPRoLOGiii
il)(_RO0
;fiiI.E€HPfRK)_
l)l)]:(1)l
mm_-=r_m
_
_
o-o]
::::::::::::::::::::::::::::::
::.:.::::.:.::
i:.:i:!_
...............
i:;:!::
...............
...............
...............
i:.:i:!::
.....................
)l
Indicates clock, total playing time, elapsed time, remaining time, title
number, chapter/track number, channel, radio frequency, level, volume,
channel or current deck status (Playback, Pause, Mode, etc).
Lights when TV mode is active.
The VCR deck is selected.
Indicates repeat mode
DVD DVD inserted.
PHOTO Photo disc inserted.
VCD Video CD inserted.
MP3 MP3 disc inserted.
ST Indicates a stereo broadcast is being received.
Indicates when the Progressive scan playback is in progress.
m
m
I
I
I
I
TV
Switches TV ON and OFE
POWER (I/V)
Switches DVD/VCR Receiver ON and OFF.
INPUT •
- Selects the VCR deck's source
(Tuner, LINE 1, er LINE 2) in VCR mode.
- Selects the TV external source in TV mode.
• TV
To control multi-brand TV.
• DVD/CD
To control DVD/CD operating.
AUX •
To listen to an audio source connected to the
• VCR
To control VCR operating.
DIGITAL AUDIO IN (OPTICAL) jack with
video from LINE 1.
SOUND MODE •
Selects sound mode between BYPAS& PRO
LOGIC, PRO LOGIC I] (MOVIE, MUSIC,
MATRIX) and 3D SURROUND.
OPEN/CLOSE,
EJECT ( _ ) •
- Opens and closes the disc tray.
- Ejects the tape in the VCR deck.
uINPUT
TV
POWER
POWER
AUX
SOUND
MOOE
• FM/AM
Selects the DVDNCR Receiver's tuner as
the listening choice (FM and AM bands).
PROGRAM
Accesses or removes Program menu.
EJECI
CCI CD CD
COUNT RESET, CLEAR
- Resets tape counter to 0:00:00
- Removes a track number en the
program menu er a mark on the
MARKER SEARCH menu.
0-9 numerical buttons
Selects numbered options in a menu.
ZOOM
Enlarges DVD/VCD video image.
ANGLE •
J
©©d J
Displays the disc's Title menu, if available.
DISC MENU
Accesses menu on a DVD disc.
Selects a DVD camera angle if
ANGLE
SUB TITLE
RETURN
- Removes the setup menu.
- Displays the menu of a video CD with
PBC.
AUDIO
available. _
SUBTITLE •
Selects a subtitle language.
AUDIO •
Selects an audio language (DVD) or an audio
channel (CD).
SLOW •
Forward slow playback ef tape.
MARKER
©
¸TUNING
SEARCH
eVOLUME
eCH/IRK
Displays MARKER SEARCH menu.
VOLUME (A/V)
-Adjusts volume of speaker.
-Adjusts volume of TV in TV mode.
PAUSE/STEP •
Pause playback or recording
temporarily/press repeatedly for
"CII/TRK
SLOW
- For fast
reverse picture
search.• _1
frame-by4rame
playbaCk.PLAY
- Rewinds the tape during the STOP mode.
FWD •
STOP
PAUSE/STEP PLAY
©C]@ E>
REW
REC/ITR
WD
REPEATA-B
SKIP
REPEAT
RANDOM
C3 C3 CB
SP/SLP
- For fast forward picture search.
-Advances the tape during the STOP mode.
SKIP (14_1) •
- Skip to beginning of current DVD/CD chapter or track, press twice in quick succession
to go to previous DVD/CD chapter or track.
- Press and hold for a fast reverse picture
search in DVD mode.
REPEAT A-B, SP/SLP •
- Repeats sequence.
- Selects recording speed.
REPEAT •
Repeat chapter, track, title, all.
RANDOM •
DISPLAY, CLK/CNT
Accesses On-Screen display.
Switches among the clock, tape counter and
tape remaining modes on the display.
4/I_/A_ (left/right/up/down)
Selects an option in the menu.
CH/TRK (A_): Selects VCR channels in
VCR mode ; Selects TM channels in TV
mode.
Manually adjusts the tape's picture
onscreen in VCR mode.
4/1_ can also change the speed of VCR
playback. For example, slow, still, 2x play,
3x play, review and cue.
TV/VCR
To view channels selected by the VCR tuner
or by the TV tuner.
SKIP (1_1_1)•
- Skip te next DVD/CD chapter or track.
- Press and hold for a fast forward picture
search in DVD mode.
REC/ITR (0) •
Records normally or activates Instant Timer
Recording.
TUNING (A/V)
To tune in the desired station.
MARKER
Marks any point during playback.
SEARCH
STOP •
Stops playback.
Starts playback.
REW •
TOP MENU
ENTER, MEMORY
-Acknowledges menu selection.
Displays functions on the TV screen.
Note
This remote control uses the
same buttons for VCR and
DVD functions (ex. PLAY).
To use the VCR, first press
the VCR button.
To use the DVD, first press
the DVD/CD button.
SETUP, MENU
Accesses or removes DVD Setup menu and
VCR menu.
MUTE
Turns off sound from speaker connectors.
Plays tracks in random order.
I
i
i
I
I
VCR IN LINE 1 (VIDEO IN/AUDIO IN
(Left/Right))
Connect the audio/video output of an external
source (Audio system, TV/Monitor, Another
VCR).
/
DVD/VCR OUT (VIDEO/AUDIO (Left/Right))
Connect to a TV with video and audio inputs.
COMPONENT/PROGRESSIVE
SCAN VIDEO OUT
(Y Pb Pr) (DVD OUT)
Connect to a TV with Y Pb Pr inputs. FOR DVD
VIEWING ONLY.
AC Power Cord
ANT.IN
Connect the VHF/UHF/CATV
antenna to this terminal.
lug into the power source.
....®®®o
REOUT I
Connect to a TV with RF coaxial inputs. J
S-VIDEO OUT (DVD OUT)
Connect to a S-Video Input on TV. FOR DVD VIEWING ONLY.
SPEAKER Connectors
Connect the six supplied speakers to these terminals.
DIGITAL AUDIO IN (OPTICAL)
Connect to a digital audio output on a digital device.
Do not touch the inner pins of the jacks on the rear
panel.
Electrostatic discharge may cause permanent damage to the unit.
Remote
Control
Operation
Range
Point the remote control at the remote sensor and
press the buttons.
• Distance: About 7m (23ft) from the front of the
remote sensor
• Angle: About 30 ° in each direction of the front of the
remote
Remote
sensor
control
battery
installation
Detach the battery cover on the rear of
the remote control, and insert two R03
(size AAA) batteries with © and •
aligned correctly.
AM Antenna Connectors
Connect the AM antenna to this terminal.
FM Antenna Connector_
Connect the FM antenna to this terminal.
_Caution
Never throw batteries into a fire.
Notes
• Be sure to use AAA size batteries.
• Dispose of batteries in a designated disposal area.
• Batteries should always be disposed of with the environment
in mind. Always dispose of batteries in accordance with
applicable laws and regulations.
• If the remote control does not operate correctly, or if the
operating range becomes reduced, replace batteries with
new ones.
• When necessary to replace batteries in the remote control,
always replace both batteries with new ones. Never mix battery types or use new and used batteries in combination.
• Always remove batteries from remote control if they are dead
or if the remote control is not to be used for an extended
period of time. This will prevent battery acid from leaking into
the battery compartment.
Tips
Without
•
Depending on your TV and other equipment you wish to
connect, there are various ways you could connect the
DVD/VCR Receiver. Use connections described on pages
11-14.
•
Please refer to the manuals of your TV, VCR, Stereo
If your cable wire is connected to your TV without a converter
or descrambler box, unscrew the wire from your TV and attach
it to the ANT.IN jack on the DVD/VCR Receiver. Use the supplied round coaxial cable to connect between the DVD/VCR
Receiver's RROUT jack and the 75 ohm antenna input jack on
the TV. With this connection, you can receive all midband,
super band, and hyperband channels.
System or other devices as necessary to make the best
connections.
Cable
Box
Z_Caution
With
•
If a converter is required in your cable system, follow the
instruction below:
Make sure the DVD/VCR Receiver is connected directly to
the TV. Tune the TV to the correct video input channel.
Do not connect the DVD/VCR Receiver's DVD/VCR AUDIO
•
OUT jack to the phono in jack (record deck) of your audio
system.
Do not connect your DVDNCR Receiver via your VCR. The
DVD image could be distorted by the copy protection system.
•
•
The unauthorized recording, use, distribution, or revision of
television programs, videotapes, DVDs and other materials,
is prohibited under the Copyright Laws of the United States
and other countries, and may subject you to civil and/or
criminal liability.
Connecting Antenna/Cable
DVD/VCR Receiver
1,
2.
TV to
Cable
Box
The cable hookup permits both TV and DVD/VCR Receiver
operation.
To view or record a CATV channel
1 Tune the TV to the DVDNCR Receiver output channel (CH
3 or 4).
2 Set the DVDNCR Receiver channel selector to the output
channel of the Cable Converter box using CH/TRK (A/V) or
number (0-9) of your DVD/VCR Receiver. (Example: CH3)
3 Select the channel to view at the Cable Converter Box.
Notes
• With this connection, you CANNOT record one program
while viewing another.
• If you are using a cable box to tune channels, it is not necessary to do Auto Channel Programming, (Auto Channel
Search) as indicated on page 18.
Disconnect the antenna leads from the rear of the
TV.
Cable
Identify the type of cable from your antenna. If it is a
round cable as illustrated, it is a 75 ohm coaxial
antenna cable. This cable will connect directly to the
jack marked ANT.IN on your DVDNCR Receiver.
Tip
If your antenna lead wire is a flat type antenna cable,
connect it to an Antenna Adaptor (300-ohm to 75-ohm)
(not supplied) and slip the Adaptor onto the ANT.IN
jack. The Adaptor does not screw on to the DVD/VCR
Receiver, it just slips over the jack.
Antenna
Back
Panel
of
Typical
Cable
Box
i
Cable TV
Wall Jack
®®®o
Rear of DVD/VCR Receiver
Flat W
(300 ohm)
300/75 ohm _
Adaptor
(Not supphed)
OR
_
9
OR
'
o
Rear of DVD/VCR Receiver
L_
CABLE
....
®®®o
Antenna
TV
Wall Jack
®
I
I
Basic TV Connections
Optional
Make one of the following connections,
the capabilities of your TV.
RF coaxial
depending on
connection
Connect the RF.OUT jack on the DVDNCR Receiver to
the antenna in jack on the TV using the 75-ohm Coaxial
Cable supplied (R).
Note
If you use this connection, tune the TV to the
DVDNCR Receiver's RF output channel (CH 3 or 4).
How to set the DVD/VCR Receiver's RF output channel
When the DVD/VCR Receiver is turned off, press and
hold CH/PRESET (/_/_/)
on the front panel for about
five seconds to change the RF output channel (CH 03
or CH 04). "RF-03" or "RF-04" appears in the display
window.
Audio/Video
connection
1. Connect the DVDNCR VIDEO OUT jack on the
DVD/VCR Receiver to the video in jack on the TV
using the supplied video cable (V).
2. Connect the Left and Right DVDNCR AUDIO OUT
jacks on the DVD/VCR Receiver to the audio
left/right in jacks on the TV (A) using the supplied
audio cables.
Note
If you use this connection,
to VIDEO.
Note
DVD playback can also be done using the S-VIDEO OUT
and COMPONENT/PROGRESSIVE
SCAN VIDEO OUT
connection options below. The tuner and VCR ONLY
output through the RROUT (R) or DVDNCR OUT (A,
V) jack. (See left)
S-Video
Connection
1. Connect the S-VIDEO OUT jack on the DVD/VCR
Receiver to the S-Video in jack on the TV using the
S-Video cable (S).
2. Connect the Left and Right AUDIO OUT jacks on
the DVDNCR Receiver to the audio left/right in
jacks on the TV using the supplied audio cables (A).
Component
Video
(ColorStream
®) connection
1. Connect the COMPONENT/PROGRESSIVE
SCAN
VIDEO OUT jacks on the DVDNCR Receiver to the
corresponding in jacks on the TV using Y Pb Pr
cables (C).
2. Connect the Left and Right AUDIO OUT jacks of the
DVDNCR Receiver to the audio left/right in jacks on
the TV (A) using the supplied audio cables.
Progressive
Scan (ColorStream
Pro ® ) connection
•
If your television is a high-definition or "digital ready"
television, you may take advantage of the DVD/VCR
Receiver's progressive scan output for the highest
video resolution.
•
If your TV does not accept the Progressive Scan format, the picture will appear scrambled if you try
Progressive Scan on the DVDNCR Receiver.
set the TV's source selector
Rear of TV
TV Connections
1. Connect the COMPONENT/PROGRESSIVE
SCAN
VIDEO OUT jacks on the DVDNCR Receiver to the
corresponding in jacks on the TV using Y Pb Pr
cable (C).
a-
2. Connect the Left and Right AUDIO OUT jacks of the
DVDNCR Receiver to the audio left/right in jacks on
the TV (A) using the supplied audio cables.
Notes
• Set the Progressive Scan to "On" on the DVD setup
menu for progressive signal, see page 21.
J
• Progressive scan does not work with the analog video
connections (yellow VIDEO OUT and S-VIDEO OUT
jack).
Rear of DVD/VCR Receiver
m
m
I
I
Speaker System Connections
Speaker Positioning
Connect the speakers using the supplied speaker cords
by matching the colors of the terminals and those of the
cords. To obtain the best possible surround sound,
adjust the speaker parameters (distance, level, etc.).
For a normal setup use 6 speakers (2 front speakers,
center speaker, 2 rear speakers and subwoofer).
Notes
• Be sure to match the speaker cord to the appropriate
terminal on the components: (_ to (_ and Q to Q. If
the cords are reversed, the sound will be distorted
and lack bass.
• If you use front speakers with low maximum input rating, adjust the volume carefully to avoid excessive
volume output to the speakers.
• Do not disassemble the front covers of supplied speakers.
Front Speaker
(RUght)
Center
Speaker
Front Speaker
(Left)
• Front Speakers
Based on your listening position, set up the speakers
at equal distance. And by hearing position, set up an
interval between speakers of 45 degree.
• Center Speaker
It is ideal that the center speakers and front speakers
are same height. But normally place it above or below
the television as shown below.
• Rear Speakers
Place the rear surround speakers to the left and right
behind the primary listening area. These speakers
recreate sound motion and atmosphere required for
surround playback. For best results, do not install the
rear speakers too far behind the listening position,
install them at or above the level of the listener's ears.
It is also effective to direct the rear speakers towards
a wall or ceiling to further disperse the sound.
In the case of a smaller room size, if the audience is
near to the rear wall set the rear speakers opposite
each other, and set the rear speakers 60 - 90 cm
above the listener's ears.
• Subwoofer
This can be placed in any front position.
Subwoofer
Center Speaker
Front
Front
Speaker
(Right)
Speaker
Rear
Speaker
(Left)
Rear speaker
•
(Right surround)
Subwoofer
About
1
2
Ferrite
Core
Be sure to attach the ferrite core to
the speaker cables (for connecting to
this unit).
This ferrite core can reduce noises.
How
3
Rear speaker
(Left surround)
to attach
1 Push
the ferrite
core.
the stopper [a] of the ferrite core
to open.
2
Wind the Center and Subwoofer Speaker
cables once on the ferrite core.
Pass the others straight on the ferrite core.
3 Close the ferrite core until it clicks.
Rear
Speaker
(Right)
Speaker Positioning
Example
Radio Antenna
Connections
Connect the supplied FM/AM antennas for radio listening.
1. Connect the AM loop antenna to the AM antenna
connectors.
2. Connect the FM wire antenna to the FM antenna
connectors.
Notes
• To prevent noise pickup, keep the AM loop antenna
away from the DVDNCR Receiver and other components.
• Be sure to fully extend the FM wire antenna.
• After connecting the FM wire antenna, keep it as horizontal as possible.
Digital Device Connections
Connect the DIGITAL AUDIO IN (OPTICAL) jacks on
the DVD/VCR Receiver to the digital audio out (optical)
jacks on your digital device (Game device, Digital Set
Top Box, etc.), using optional optical audio cable.
To select source of DVD/VCR Receiver to OPTICAL IN,
press AUX on the remote control.
Notes
• If the audio format of the digital output does not
match the capabilities of your DVD/VCR Receiver, the
DVD/VCR Receiver will produce a strong, distorted
sound or no sound at all.
• The Optical input function is available only when the
other unit's Sampling Frequency is 32 - 48kHz.
Game Device
Digital Set Top Box
! o
_
i
Rear of DVD/VCR
Receiver
Accessory Audio/Video (A/V)
Connections
to DVD/VCR
Receiver
Connect the VCR IN LINE1 or LINE in 2 jacks on the
DVDNCR Receiver to the audio/video out jacks on your
accessory component, using optional audio/video
cables.
Jack
Panel of Accessory
(VCR, Camcorder,
Component
etc,)
OR
RearofDVD/VCRReceiver
Frontof DVD/VCRReceiver
Rear of DVD/VCR Receiver
.... O,,)
I
I
AUX
DVD/CD
VCR
FM AM
Follow these guidelines to select and switch among the
various DVDNCR Receiver input and output sources:
• DVD/CD
To view output from the DVD deck:
Press DVD/CD on the remote or DVD/VCR on the
front panel until the DVD indicator on the front panel
lights and output from the DVD deck is viewed on the
TV screen.
• VCR
ekNPUT
INPUT
MODE
_
EJECT
SOUND
OPEN,CLO_
,
To view output
from the VCR deck:
Press VCR on the remote or DVDNCR on the front
panel until the VCR indicator on the front panel lights
and output from the VCR deck is viewed on the TV
screen.
• FM/AM
(DO
_
RETURN
ANGLE
SU£ TITLE
DISC MENU
Press FM/AM on the remote to toggle between AM
and FM radio. The selected frequency appears on
the front panel display.
MARKER
O
TbNING
SEARCH
AUX
eVOLUME
DIS PlAY
SET
O
UP
.oH,Tr,
K O
CLK/CNT___MENU
TV/VCR
SLOW
@
MUTE
STOP
PAUSESTEP
C> c0
REC/ITR
REPEATA=B
To listen to AM/FM radio broadcasts:
AUDIO
REPEAT
PLA'Y
SKIP
RANDOM
C3 C3 C3
To listen to an audio source connected to the
DIGITAL AUDIO IN (OPTICAL) jack with video
from LINE 1:
Press AUX on the remote control once. L1 OPT will
appear on the front panel display. Audio will come
from an external source connected to the DIGITAL
AUDIO IN (OPTICAL) jack and video will come from
an external source connected to the VIDEO IN jack
of LINE 1 (for rear panel).
To listen to an audio source connected to the
AUDIO IN jack of LINE1 with video from LINE 1:
Press AUX on the remote control a second time.
L1 will appear on the front panel display. Audio will
come from an external source connected to the
AUDIO IN jacks of LINE1 (for rear panel) and video
will come from an external source connected to the
VIDEO IN jack of LINE 1 (for rear panel).
INPUT
To view a source connected to the front or rear
LINE inputs:
First, press VCR to select the VCR deck, and then
press INPUT to select LINE1 (L1) (for rear panel) or
LINE2 (L2) (for front panel).
m
I
I
Mini Glossary for Audio Stream &
Surround mode
Software with multichannel surround audio signals is played
according to the way it was recorded.
Sound Mode
(DTS)
Allows you to enjoy 5.1 (or 6) discrete channels of high quality
digital audio from DTS program sources such as discs, DVD
and compact discs, etc.bearing the trademark. DTS Digital
Surround delivers up to 6 channels of transparent audio(which
means identical to the original masters) and results in exceptional clarity throughout a true 360 degree sound field. The
term DTS is a trademark of DTS Technology, LLC.
Manufactured under license from DTS Technology, LLC.
NDDIGITAL
BYPASS
(Dolby
Digital)
The Dolby Digital surround format lets you enjoy up to 5.1
channels of digital surround sound from a Dolby Digital program source. If you play DVDs with " uu_,
mark, you can
enjoy even better sound quality, greater spatial accuracy, and
improved dynamic range.
DDPF{0LOGIC
(Dolby
Pro Logic)
Use this mode when playing movie or Doiby Digital 2 channel
which carries the" _
" mark. This mode provides the effect
of being in a movie theater or live concert house-an effect with
an intensity which can only be obtained through DOLBY PRO
LOGIC SURROUND.
The effect of the front/back/left/right
movement of the sound image, as well as the sense of fixed
position in the sound image, is much clearer and more dynamic than before.
[_DPR0 LOGIC Ill
(Dolby
Pro Logic
You can enjoy surround sound simply by selecting one
of the pre-programmed sound fields according to the
program you want to listen to.
Press SOUND MODE repeatedly until the sound mode
you want appears in the display window as below.
Each time you press SOUND MODE button, the sound
mode is changed in the following order;
BYPASS -_ PRO LOGIC -_ MOVIE -_ MUSIC -_ MATRIX-_
3D SURR
When DVD is inserted.
You can change the sound mode of DMD (Dolby Digital, DTS,
PCM, etc) by pressing the AUDIO button on the remote
during playback.
Although the DVD contents differ from disc to disc, the following explains the basic operation when this feature is used.
Each time you press AUDIO button, the sound mode of DVD is
changed as the following order;
DDDIGITAL-_ P'Z_J -_
PCM -_ DDDIGITAL
Note
Depending on discs format, you may not be able to change the
sound mode.
ll)
Dolby Pro Logic II creates five full-bandwidth output channels
from two-channel sources. This is done using an advanced,
high-purity matrix surround decoder that extracts the spatial
properties of the original recording without adding any new
sounds or tonal colorations.
MOVIE mode:
The Movie mode is for use with stereo television shows and all
programs encoded in Dolby Surround. The result is enhanced
soundfield directionality that approaches the quality of discrete
5.1-channel sound.
MUSIC mode:
The Music mode is for use with any stereo music recordings, and
provides a wide and deep sound space. The Music mode
includes controls that allow the sound to be tailored to individual
listening tastes.
MATRIX mode:
The Matrix mode is the same as the Music mode except that the
directional enhancement logic is turned off. It may be used to
enhance mono signals by making them seem "larger." The Matrix
mode may also find use in auto systems, where the fluctuations
from poor FM stereo reception can otherwise cause disturbing
surround signals from a logic decoder. The ultimate "cure" for
poor FM stereo reception may be simply to force the audio to
mono.
3D SURROUND
This unit can produce a 3D Surround effect, using 3D Surround
Sound technology, which simulates multi-channel audio playback from two conventional stereo speakers instead of the five
or more speakers normally required to listen to multi-channel
audio from a home theater. This feature works with DVD discs
encoded with Dolby Pro Logic and Dolby Digital audio tracks.
For your reference
• The DVD/VCR Receiver memorizes the last mode
settings for each source individually.
• You can identify the encoding format of program
software by looking at its packaging.
- Dolby Digital discs are labelled with the PuB logo.
- Dolby Surround encoded programs are labelled with
the @_
logo.
- DTS Digital Surround discs are marked with _.
Note
When you play sound tracks with 96kHz sampling frequency,
the output signals will be converted to 48kHz (sampling
frequency).
Volume Control
You can adjust the volume by rotating VOLUME on the
front panel or by pressing VOLUME (A/_') on the
remote control repeatedly.
Muting
Press
MUTE
You can mute
to mute
your
unit.
your unit in order,
the telephone,
"MUTE" indicator
will light up. To exit mute mode,
for example,
to answer
in the display window
press MUTE again.
On-Screen
Display (OSD)
Set the Output Source to VCR as shown in "Selecting
the Input/Output Source" on page 15.
Some of these functions appear during VCR operated.
0
@
@
0
OTAPE SPEED DISPLAY
Shows the current tape speed.
€ FUNCTION DISPLAY
Indicates the current function.
€ HI-FI DISPLAY
EASY INFORMATION
If the Extended Data Service (XDS) signals are provided
along with normal TV signal in your area or during playback of a tape recorded with Extended Data Service
(XDS) signals, the station ID, program title, and program
details are shown on the TV screen.
When viewing a channel with Extended Data Service (XDS)
signals, press ENTER and the station ID will appear on the
TV screen. Press ENTER again and the program details will
appear on the TV screen.
When viewing a tape recorded with Extended Data
Service (XDS) signals, press ENTER twice and the program title and program details will appear on the TV
screen.
PROGRAM DETAILS
LENGTH: Indicates the run length of a program.
TIME REMAINING: Indicates the remaining time of a
program.
RATING: Indicates the rating of the current program
(N/A, G, PG, PG-13, R, NC-17, X and Not Rated). The
rating N/A means that the motion picture ratings are not
applicable to this program.
Indicates the unit is playing back tape recorded in Hi-Fi.
O CHANNEL DISPLAY
Indicates the selected channel (or LINEI(L1), LINE2(L2)).
STEREO/SAP DISPLAY (MONO is not displayed)
Shows the type of audio signal received by the VCR tuner.
© DATE DISPLAY
Shows the current date. (Month/Date/Day of the week
format)
CLOCK/COUNT/REMAIN
DISPLAY
Shows the current time, the tape counter and remaining time
on the tape.
Each press of the ENTER changes the TV
on-screen displays in the following sequence.
TO
SP
OCT
SP
CH 4
STEREO
WABC
"Home video"
OCT 8, SAT
2:15 PM
Easy Information Screen
(Station ID)
PROGRAM DETAILS
"Home video"
LENGTH
01:00
TIME REMAINING
RATING
00:26
N/A
Easy Information Screen
(Program details)
On-Screen Menus Setup
The SETUP, clock setting (CLOCK), and timer
recordings (PROGRAM) are accessed conveniently with
the on-screen menus, that lead you through each step.
The following pages describe the on-screen menu
selections available.
STEREO
8 , SAT
Menu Selection
Your VCR allows remote control adjustment of several
features.
1. Press MENU and the MAIN menu will appear.
2:15 PM
I
I
°:35:°-L
Notes
2. Select the desired menu with &/v button and
then press ENTER.
Note
Menus remain on-screen for 3 minutes.
MAIN MENU
• The function displays remain on the TV screen for 5
seconds.
• The clock (or tape counter, tape remaining) mode will remain
on the screen until you press ENTER.
• The tape counter and the remaining tape length indicator
appear only when a cassette is inserted. Also, the remaining
tape length indicator appears after any tape operation.
CLOCK SET (page 19)
]CLOCK
]
PROGRAM
PROGRAM
]
TUNING
TUNING (page 18)
]
SETUP
SETUP (page 18)
_RE SS 1'_9'_ravl
3.
Press MENU when finished.
(page 25)
VCR Setup Menu Options
Channel Selection
1. Press MENU and the MAIN menu will appear.
This DVD/VCR Receiver is equipped with a
frequency synthesized tuner capable of receiving up to
181 channels. These include VHF channels 2-13, UHF
channels 14-69 and CATV channels 1-125.
2. Use A/• to select the SETUP menu, then press
ENTER.
The SETUP menu will appear.
Preparation:
Connect the DVD/VCR Receiver to the desired type of antenna
or cable TV system, as shown in Connecting Antenna/Cable
TV to DVD/VCR Receiver on page 11.
AUTO
3. Use A/V to choose a desired option on the
SETUP menu. Then use </1_ to choose a desired
setting.
FUNCTION
CHANNEL
PROGRAMMING
1.
Press MENU and the MAIN menu will appear.
2.
Use A/• to select the TUNING menu, then press
ENTER.
The TUNING menu will appear.
3.
Use • to choose the SOURCE SELECT option,
then use </1_ to select TUNER.
Press </1_ repeatedly to switch between TUNER,
LINE1(L1) and LINE2(L2).
4.
Use A/• to choose the AUTO CHANNEL SET option,
then use 4/1_ to search for channels.
The tuner will automatically cycle through all
available channels in the area and place them in the
tuner's memory.
OSD
The on-screen display of this DVDNCR Receiver can be turned
on or off.
• FUNCTION OSD can be switched between ON and OFF
using 4/1_.
AUDIO
MODE
The DVDNCR Receiver has two separate audio playback systems, the high quality VHS Hi-Fi system and standard NORMAL mono system. The same audio is generally recorded on
both systems. The VHS Hi-Fi system plays on separate (left
and right) channels, and the NORMAL system plays monaural
sound. The normal track is always played so the cassette can
be played on a DVD/VCR Receiver that does not have VHS
Hi-Fi.
• AUDIO MODE can be switched between HI-FI and
NORMAL using 4/1_.
BROADCAST
TYPE (STEREO/SAP/MONO)
Multichannel Television Sound (MTS) carries stereo and/or
Second Audio Program (SAP) bilingual signals. Set this display to
the desired position when both MTS stereo and SAP signals are
received. When only one of the MTS signal is received, the
DVD/VCR Receiver automatically selects the corresponding
receiving mode (Stereo or SAP) regardless of the selected position. For normal operation, the display should be in the STEREO
position. The DVD/VCR Receiver will then record a STEREO program when available, and record a mono program IF the program is
NOT IN STEREO.
For weak STEREO and/or SAP broadcasts, changing the display to mono may give clearer sound.
• BROADCAST TYPE can be switched between STEREO,
SAP, and MONO using _1/1_.
AUDIO OUTPUT (STEREO/LEFT/RIGHT)
Used during playback [when AUDIO MODE (HI-FI/NORMAL) is
in HI-FI position] for selecting the audio output signals from the
AUDIO OUT terminals (L ch and R ch), and RROUT.
This display setting should normally be left in the stereo position, so that when a stereo tape is played, the stereo sound will
be heard through the left and right channels. If a mono tape is
played and the audio output is set to stereo, the same mono
sound will be heard from both left and right channels.
• AUDIO OUTPUT can be switched between STEREO, LEFT,
and RIGHT using 4/1_.
4.
Press
MENU
when
5. After the AUTO CHANNEL SET PROCEEDING is
complete, make sure the TUNING BAND is set
appropriately (TV or CATV) using A/• and
choosing the correct TUNING BAND (TV or
CATV) by using </1_ while in the TUNING menu.
Remember, TV is for the air antenna reception,
CATV is for cable or wireless cable connection.
6.
7.
Press MENU to return to the TV screen.
Use CH/TRK (&/•) on the remote control or
CH/PRESET (/_/V)
on the front panel to cycle
the DVD/VCR Receiver through the channels in
memory.
TO ADD OR ERASE CHANNELS
FROM MEMORY
This feature allows you to add or erase channels in
memory manually.
1
Press • to choose the CH. ADD/DEL option on the
TUNING menu. Use </1_ to select a channel to add
or erase.
2
Press ENTER to add or erase the channel.
Repeat steps 1 and 2 to add or erase channels.
3
Press MENU to return to the TV screen.
finished.
I
I
Note
Setting the Clock
There are cases where the TV station does not send or sends
The DVD/VCR Receiver gives you two ways to set the
time and date: the Auto Clock Feature or manually. The
Auto Clock feature enables the DVD/VCR Receiver to
set up the clock while the DVD/VCR Receiver is turned
off.
*
Manual
1.
Press MENU and the MAIN menu will appear.
2.
Use _
to choose the CLOCK menu.
Press ENTER and the CLOCK menu will appear.
The initial Clock Setting is JANUARY
1, 2005, 12:00 AM.
}=
Auto Clock Set
The Auto Clock Set feature is set to ON at the factory. In the
ON setting, the DVDNCR Receiver looks for a channel carrying XDS (Extended Data Services) information. XDS updates
the clock using the Coordinated Universal Time.
The Auto Clock feature enables the DVD/VCR Receiver
to set up the clock while the DVD/VCR Receiver is
turned off.
3.
Use &/• to choose the CLOCK menu.
Press ENTER and the CLOCK menu will appear.
m
CLOCK
1
Use • to choose the DAY option.
Use •/1_ to choose the date.
The day of the week will display automatically.
5.
Use • to choose the YEAR option.
Use </1_ to choose the year.
6.
Use • to choose the TIME option.
Use </1_ to choose the time.
Press and hold _1/1_to advance clock
continuously.
7.
Use • to choose the DAYLIGHT SAVINGS option.
Use • or I_ to choose AUTO, ON, or OFF.
If you choose AUTO, the VCR sets the clock using the
DST information broadcast in the signal (channel).
If you choose ON, the VCR adjusts the clock for Daylight
Saving Time automatically.
8.
Press MENU when finished.
__
3.
Use • to choose the AUTO CLOCK SET option.
Use </1_ to choose ON.
4.
Use • to choose the DAYLIGHT SAVINGS option.
Use • or I_ to choose AUTO, ON, or OFF.
If you choose AUTO, the DVDNCR Receiver sets the
clock using the DST information broadcast in the signal
(channel). If you choose ON, the DVD/VCR Receiver
adjusts the clock for Daylight Saving Time automatically.
5.
Use • to choose the TIME ZONE option.
Use • or I_ to choose the correct time zone
(AUTO, EASTERN, CENTRAL, MOUNTAIN,
PACIFIC, ALASKA or HAWAII).
If "AUTO" is selected as the time zone, the DVD/VCR
Receiver sets the clock using the first Coordinated
Universal Time information it finds in a broadcast signal.
6.
Press MENU when finished.
7. Turn off the DVD/VCR Receiver and the auto
clock set feature sets the time.
Use </1_ to choose the month.
4.
1. Press MENU and the MAIN menu will appear.
2.
Clock Set
The clock uses the 12-hour system. (Be sure to set AM
and PM correctly.)
*
the wrong time. Therefore, the incorrect time will be set. If this
happens we recommend that you set the clock manually.
Note
If setting the clock manually, "AUTO CLOCK SET" must
set to "OFF".
If set to "ON", an incorrect date and/or time will be
entered again when the DVD/VCR Receiver is turned
off.
I
I
General Explanation
Temporary Feedback Field Icons
This manual gives basic instructions for operating the
DVD/VCR Receiver. Some DVDs require specific operation or allow only limited operation during playback.
When this occurs, the symbol @ appears on the TV
screen, indicating that the operation is not permitted by
the DVD/VCR Receiver or is not available on the disc.
® ..... : Repeat Title
.......................
@o"_"_: Repeat Chapter
_ ..... Repeat Track (non-PBC Video CDs
..........
and Audio CD only)
[email protected] _LL
On-Screen Display
Repeat Disc (non-PBC Video CDs
and Audio CD only)
Repeat A-B
Set the Output Source to DVD as shown in "Selecting
the Input/Output Source" on page 15.
i_0FFi
General playback status can be displayed on the TV
screen. Some items can be changed on the menu.
@
Repeat Off
Resume play from this point
On-screen
Action prohibited or not available
Notes
• Some discs may not provide all of the features on the
on-screen display example shown below.
• If no button is pressed for 10 seconds, the on-screen
display disappears.
display operation
1. Press DISPLAY during playback.
2. Press A/V to select an item.
The selected item will be highlighted.
3. Press ,4/1_to change the setting of an item.
The number buttons can be also used for setting
numbers (e.g., title number). For some functions,
press ENTER to execute the setting.
!
Items
Function
Title Number
Shows the current title number and total number of
titles, and skips to the desired title number.
Chapter Number
Shows the current chapter number and total number of
chapters, and skips to the desired chapter number.
Time search
Shows the elapsed playing time, and
searches the point directly from the elapsed time.
Audio language
and Digital Audio
Output mode
Subtitle language
Shows the current audio soundtrack
language,
encoding method, and channel number, and
changes the setting.
Angle
Shows the current angle number and total number
angles, and changes the angle number.
Sound
Shows the current sound
changes the setting.
Items
Function
Track Number
Shows the PBC On mode or current track number, total
number of tracks and skips to the desired track number.
Time
Shows the elapsed
Audio Channel
Shows the audio channel, and
changes the audio channel.
Sound
Shows the current sound mode, and
changes the setting.
(Press A/V to select desired item)
Shows the current subtitles
changes the setting.
(Press
A/T
language,
Selection
< /1_, or Numbers,
ENTER
< /1_, or
AUDIO
and
playing
desired
time (Display
/1_, or Numbers,
ENTER
Numbers, ENTER
< /1_, or
SUBTITLE
of
mode, and
to select
Method
< /1_, or
ANGLE
< / I_, or
SOUND MODE
item)
Selection
Method
< /1_,or Numbers,
ENTER
only)
< /1_, or
AUDIO
< /1_, or
SOUND MODE
m
m
I
I
I
I
Initial Settings
You can set your personal preferences on the DVD/VCR
Receiver.
General Operation
1. Press SETUP.
The Setup menu appears.
2.
Use A/T to select the desired option.
The screen will show the current setting for the
selected option, as well as alternate setting(s).
3. While the desired option is selected, press I_,
then A/T to select the desired setting.
4.
Press ENTER to confirm your selection.
Some options require additional steps.
5.
Press SETUP, RETURN, or PLAY to exit the setup
menu.
Language
Picture
TV Aspect
4:3 Letterbox: Select when a standard 4:3 TV is connected. Displays pictures with masking bars above and
below the picture.
4:3 Panscan: Select when a standard 4:3 TV is connected. Displays pictures cropped to fill your TV screen.
Both sides of the picture are cut off.
16:9 Wide: Select when a 16:9 wide TV is connected.
Progressive
Scan |
Progressive Scan Video provides the highest resolution
pictures with less flicker and line structure.
If you are using the COMPONENT/PROGRESSIVE
SCAN VIDEO OUT jacks, but are connecting the
DVDNCR Receiver to a standard (analog) television,
set Progressive Scan to Off.
If you are using the Component Video jacks for
connection to a TV or monitor that is compatible with a
progressive scan signal, set Progressive Scan to On.
Disc Language
Select a language for the disc's Menu, Audio, and
Subtitle features.
Original : The original language set for the disc is selected.
Other : To select another language, use number buttons to
enter the corresponding 4-digit number according to the
language code list on page 44. If you enter the wrong
language code, press CLEAR.
Note
Disc Language selection may not work for some DVDs.
Menu Language
Select a language for the VCR and DVD Setup menu.
This is the menu you see when you press SETUP.
Z_Caution
Once the setting for progressive scan output is entered,
an image will only be visible on a progressive scan
compatible TV or monitor. If you set Progressive Scan
to On in error, you must reset the unit.
1) Remove any disc from the unit and close the disc
tray. See that "NO DISC" is displayed on the display
window.
2) Press STOP (m) and hold it for more then five
seconds before releasing it. The video output will be
restored to the standard setting and a picture will
once again be visible on a conventional analog TV or
monitor.
m
I
I
I
I
Speaker setup
Auto Play
5.1 Speaker
You can set up the DVDNCR Receiver so a DVD disc
automatically starts playing whenever the DVD is inserted.
settings
Select speaker settings, including volume balance and
distance, or test the speaker settings.
Speaker settings are only active on the Analog MultiChannel Output. (See "Speaker Setup", page 37.)
If Auto Play mode is set to On, this DVD/VCR Receiver
will search a title where playback time is longest and
then play back the title automatically.
On: Auto Play function is activated.
Off: Auto Play function is not activated.
Note
The Auto Play function may not work for some DVDs.
B.L.E.
(Black
Level
Expansion)
To select the black level of playback pictures. Set your
preference and monitor's ability.
Others
On: Expanded grey scale. (0 IRE cut off)
The DRC, Vocal, PBC, Auto Play, B.L.E., Pluge and
DNR settings can be changed.
Off: Standard grey scale. (7.5 IRE cut off)
•
Pluge
Use A/V to select the desired item and press
ENTER. The setting of the selected item is changed
between On and Off.
(Blacker
than Black)
For proper adjustment of your television brightness
settings utilizing a commercially available test disc.
On: Select when you adjust the level of your TV using a
commercially available test disc that contains pluge signals.
Off: For normal use.
DNR (Digital
You can reduce
DNRI:
Dynamic Range Control (DRC) |
With the DVD format, you can hear a program's soundtrack in the most accurate and realistic presentation
possible, thanks to digital audio technology. However,
you may wish to compress the dynamic range of the
audio output (the difference between the loudest sounds
and the quietest ones). Then, you may listen to a movie
at a lower volume without losing clarity of sound. Set
DRC to On for this effect.
Vocal ql_
Set Vocal to On only when a multi-channel karaoke
DVD is playing. The karaoke channels on the disc will
mix into normal stereo sound.
Noise
ambient
Reduction)
noise
in the picture.
Normal level
DNR2:
Expanded level.
Off:
Off.
Notes
• Actual picture enhancement
quality of the disc.
may vary depending on the
• While the DNR2 (expanded level) can provide additional
improvement in the reduction of noise in the video signal, it
may produce undesirable picture artifacts on some discs.
Should this occur, select a more appropriate DNR level (normal or off).
• Depending on the disc, some picture detail may be lost by
the picture enhancement.
PBC _
Set Playback
Control
(PBC) to On or Off.
On: Video CDs with PBC are played according to the PBC.
Off: Video CDs with PBC are played the same way as Audio
CDs.
m
m
I
I
Parental Control
Rating
ql_
Movies on DVDs may contain scenes not suitable for children. Therefore, discs may contain Parental Control information that applies to the complete disc or to certain
scenes on the disc. These scenes are rated from 1 to 8,
and alternatively, more suitable scenes are available for
selection on some discs. Ratings are area dependent.
DVD video discs may or may not respond to the parental
control setting if the Area code of the disc is set wrongly.
The Parental Control feature allows you to prevent discs
from being played by your children or to have certain discs
played with alternative scenes.
Area Code
ql_
Enter the code of a area whose standards were used to
rate the DVD video disc, referring to the list (See "Area
Code List", page 45).
1. Select Area Code using the &/_' buttons on the
setup menu.
2. While Area Code is selected, press •.
3. Follow step 3 of "Rating"
on left.
4. Select the first character using the &/_' buttons.
1.
Select Rating on the Setup menu using A/_'
buttons in stop mode.
2. While Rating is selected, press I_.
3. When you have not entered a password yet.
Enter a 4-digit password using the numbered buttons to create a personal 4-digit security password,
then press ENTER. Enter the 4-digit password again
and press ENTER to verify.
When you have already entered a password;
Enter a 4-digit password using the numerical
buttons to confirm the personal 4-digit security password, then press ENTER.
If you make a mistake before pressing ENTER, press
CLEAR and enter 4-digit security password again.
Select a rating from 1 to 8 using A/T buttons.
One (1) has the most playback restrictions. Eight
(8) has the least playback restrictions.
The limitation will be more severe as the level
number decreases.
Unlock: If you select Unlock, Parental Control is not
active. The disc will play in full.
Ratings 1 to 8: Some discs contain scenes not suitable for children. If you set a rating for the DVD, all
disc scenes with the same rating or lower will be
played. Higher rated scenes will not be played
unless an alternative scene is available on the disc.
The alternative must have the same rating or a
lower one. If no suitable alternative is found, playback will stop. You must enter the 4-digit password
or change the rating level in order to play the disc.
5,
Press ENTER to confirm your rating selection,
then press SETUP to exit the menu.
6.
Press OPEN/CLOSE to activate the Parental
Control. If the rating set is lower than the disc
rating, a message will appear. Select "YES" if
you want to continue playback and input the
password followed by ENTER.
5. Press • to shift to second character and select
the second character using &/V buttons.
6. Press ENTER to confirm your Area code
selection, then press SETUP to exit the menu.
Note
Confirmation of the 4-digit password is necessary when
the password is changed (see Changing the 4-digit
password below ).
Changing
the 4-digit
password
1 Follow Steps 1-2 as shown above to the left (Rating).
2 Enter the old password, then press ENTER.
3 Select Change using &/V buttons then press
ENTER.
4 Enter the new 4-digit password, then press
ENTER.
5 Enter exactly the same password a second time and
verify by pressing ENTER.
6 Press SETUP to exit the menu.
If you forget
your 4-digit
password
If you forget your password, to clear the current password follow the procedure below.
1 Press SETUP to display the setup menu.
2 Enter the 6-digit number 210499.
The 4-digit password is cleared.
3 Enter a new password as shown above to the left
(Rating).
Special Effect Playbacks
Normal Playback
Preparation:
Special
• Turn on the TV.
• Tune the TV to the DVD/VCR Receiver output channel (CH
3 or 4) or set the TV's source selector to VIDEO.
• If a direct VIDEO/AUDIO connection is made between the
DVD/VCR Receiver and the TV, set the TV's source selector
to VIDEO.
• Set the Output Source to VCR as shown in "Selecting the
Input/Output Source" on page 15.
1.
Insert
a prerecorded
video
cassette.
Receiver
notes
on the TV screen.
muted during special effect modes,
so there is no sound during search.
• During high-speed picture search mode, a short period is
needed to stabilize tape speed when re-entering the PLAY
mode. Slight interference may be observed during this period.
Search
lets you quickly
desired tape section
reverse.
and visually
in either
direction:
search
for a
forward
or
• Make sure that the (D indicator in the display
window is not lighted. If it is, press POWER once.
1 Press PEW (44)
or FWD (1_)
during playback. The
DVD/VCR
Receiver will be activated
in the SEARCH
• If a tape without a safety tab is inserted, the unit will
start playback automatically.
2 To return
Press
PLAY once.
PLAY appears
mode.
to playback,
press
PLAY.
Still Picture and Frame-by-Frame
Playback
on the TV screen.
• It is not necessary to select the tape speed for
playback. It will be automatically selected by the
DVD/VCR Receiver.
1 Press PAUSE/STEP
during playback.
Still picture will appear on the TV screen.
• If a still picture vibrates vertically, stabilize it using
• In playback, the TV/VOR selector switches to VCR
mode automatically.
3.
playback
• The audio is automatically
This function
The O'--O indicator will light and the DVDNCR
will power-up automatically.
2.
effects
• Horizontal lines (noise bars) will appear
This is normal.
CH/TRK(A/Y)
on the remote control.
• If the DVD/VCR Receiver is left in the STILL mode for
Press STOP to stop playback.
STOP appears on the TV screen.
more than 5 minutes, the DVD/VCR
• If the tape reaches the end before STOP is pressed, the
DVD/VCR Receiver will automatically stop, rewind and
eject the tape, and it will turn itself off.
Receiver will auto-
matically enter the STOP mode to protect the tape and
video heads.
2 Press
PAUSE!STEP
video
picture
repeatedly
one frame
to advance
at a time while
the
viewing
a still
picture.
Tracking Control
Auto
3 To return
The AUTO
tracking function
or streaks.
TRACKING
function
adjusts
works
the picture
to
in the following
cases:
• Tape speed (SP, SLP) changes.
Manual
Tracking
If noise
appears
on the screen
(A/T)
during
on the remote
SET (/X/_/)
on the front panel
screen is reduced.
1 Press
SLOW.
The tape will be played
slower than the normal
back at a speed
speed.
• If slow motion mode continues
• Streaks or snow appear because of scratches
CH/TRK
PLAY.
1/19 times
• During slow playback, use CH/TRK (A/Y) on the Remote
Control to minimize noise bands.
• A tape is played back for the first time.
either
press
Slow Motion
Tracking
The automatic
remove snow
to playback,
on the tape.
playback,
control
press
the DVDNCR
back mode.
2 To return
for more than 3 minutes,
Receiver will automatically
to playback,
press
change to play-
PLAY.
or OH/PRE-
until the noise
on the
• If vertical jitter is present, adjust tracking controls very
carefully.
• Tracking is automatically reset to normal when the tape is
ejected or the power cord is unplugged for more than 3
seconds.
Variable playback speed control
During
Playback
use 4/1_,
ing playback
speeds.
(-7xplay (REV), -3xplay
(STILL),
1/19 slow
you can reach
(-3PLY),
(SLOW),
the follow-
-play (-PLAY),
play
(PLAY),
2xplay
still
(2PLY),
7xplay(CUE)).
During
appear
slow motion and shuttle,
on the picture according
If distortions
with CH/TRK
can be seen
(A/T)
the noise bars may
to the status of tape.
in the picture,
on the remote
reduce
control.
them
Normal Recording
Timer Recording
Preparation:
This DVD/VCR Receiver can be programmed to record
up to 8 programs within a period of 1 year. For unattended recording, the timer needs to know the channels to be
recorded and the starting and ending times.
• Turn on the power of both the DVDNCR Receiver and TV.
• Tune the TV to the DVD/VCR Receiver output channel (CH 3
or 4) or set the TV's source selector to VIDEO.
• If a direct VIDEO/AUDIO connection is made between the
DVDNCR Receiver and the TV, set the TV's source selector
to VIDEO.
• The unauthorized recording, use, distribution, or revision of
television programs, videotapes, DVDs and other materials,
is prohibited under the Copyright Laws of the United States
and other countries, and may subject you to civil and/or
criminal liability.
1.
Insert a video cassette with the safety tab intact.
2.
Select the desired channel with CH/TRK (A/T) or
number (0-9) buttons.
If you are recording from another source via audio/video
input jacks (at the Rear or Front panel), select LINE1(L1)
or LINE2(L2) with INPUT.
3.
Set the desired recording
the SP/SLP button.
4.
Set the MTS mode
5.
Press
REC/ITR
Preparation:
• Turn on the power of both the DVDNCR
TV.
as desired
(See
page
18, 28).
appropriately
1.
Press
2.
Use A/•
3.
(The REC indicator
will light
Receiver and the
• Be sure the TV is set to the DVD/VCR Receiver output channel
(CH3 or CH4).
• Make sure the TUNING BAND in the TUNING menu is set
speed (SP or SLP) with
(O) once.
Recording
will start.
the display window.)
• If you try to set the program timer before setting the clock,
PLEASE SET THE CLOCK appears for a moment and
then CLOCK menu appears on the TV screen. Set the time
and date before proceeding.
• Make sure a tape is in the DVD/VCR Receiver and the
safety tab is in place or the tape will be automatically
ejected.
in
Press
(TV or CATV).
MENU
and the MAIN
to choose
ENTER
will appear.
the PROGRAM
to go to the
The PROGRAM
menu
menu
menu.
PROGRAM
menu.
will appear.
• If all 8 programs have been entered, FULLY
PROGRAMMED message will appear for a moment
and then PROGRAM 1 will appear on the TV screen.
• REC indicator appears only when the Output Source is
set to VCR.
• If a cassette with no safety tab is loaded, the cassette
will be ejected automatically.
[] cLOCK
m
]
PROGRAM
Press STOP to stop recording.
If the tape reaches the end before STOP is pressed, the
DVD/VCR Receiver will automatically stop, rewind, eject
the tape and turn itself off.
To pause recording
1
Press
PAUSE/STEP
to pause
the tape
When
you want
to continue
recording,
To record one TV program while
watching another
2
5.
Use • to choose the MONTH option.
Use _/1_ to choose the desired month.
6.
Use • to choose the DAY option.
Use _/1_ to choose the desired day.
7.
Use • to choose the START option.
Use _/1_ to choose the desired start time.
8.
Use •
press
PAUSE/STEP
or REC/ITR
(ll).
• After 5 minutes in Pause mode, the tape will be stopped
automatically to protect the tape and the video heads.
1
Use _/1_ to choose the PROGRAM No. (1-8).
during
recording.
The REC indicator will flash in the display window.
2
4.
Use TV/VCR to select the TV mode during recording.
"TV" appears in the display window.
Using the TV, select the channel to be viewed.
Tips
Always use PAUSE/STEP for best results when making
changes during recording.
For example: To change channels during recording, first press
PAUSE/STEP to put the unit in pause mode. Select the desired
channel on the DVD/VCR Receiver, then press PAUSE/STEP
again to resume recording.
to choose
Use _/1_ to choose
9.
the STOP
option.
the desired
Use • to choose the CHANNEL
Use _/1_ to choose the desired
(Channel,
LINEI(L1)
stop
time.
option.
channel
or LINE2(L2)).
Cable Users: If you have CABLE TV and used Cable Box
in Connecting Antenna/Cable TV to DVD/VCR Receiver
(page 11), using a cable box converter, you must set the
channel in this step to match the cable box output channel
(usually CH 3 or 4). Change channels on the cable box
instead of with the DVDNCR Receiver.
I
I
10. Use V to choose
the
SPEED
Use _/1_ to cheoee
the desired
(AUTO_ SP or SLP)o
Notes
option.
recording
speed
AUTO mode determines how much tape is left and switches speed from SP to SLP, if necessary, to complete recording the program. There will be some picture and sound distortion at the point of the speed change.
11o Use _' to choose
the REPEAT option.
Use _/_ to choose
the desired
repeat
WEEKLY
(ONCE,
or DAJLY)o
ONCE event....for recording up to 8 programs on a single
day or over the days within a period of ! year.
WEEKLY event....for recording up to 8 programs on a certain day of every week.
DAmLY event....for recording up to 8 programs at the same
time(s) Monday through Friday.
® If the power fails orthe DVD/VCR Receiver is unplugged
from the AC outlet, the correct clock time and timer settings
are kept in memory for approximately 3 seconds. After 3
seconds, the clock and program timer must be reset when
power is restored. Reset the clock according to instructions.
® After setting up a timer recording, recording will start if no
other timer recordings are scheduled to occur at the same
time (see "Program Priority" at right).
® The unauthorized recording, use, distribution, or revision of
television programs, videotapes, DVDs and other materials,
is prohibited under the Copyright Laws of the United States
and other countries, and may subject you to civil and/or
criminal liability.
Checking
(Erasing)
Programming
Timer
Programming
can be checked
Receiver is turned on=
1
2
Record
whenever
the DVD/VCR
Press MENU and the MAIN menu will appear=
Use _,/_' to choose the PROGRAM
menu.
Press
ENTER
and the PROGRAM
menu
will appear=
Tip
If the input data is wrong,
rect it using _/_.
use A to select the data and cor-
12. Press MENU, the program
the DVD/VOR Receiver.
will be memorized
by
® (2) indicator lights in the display window.
® If the program preset time has past, the PAST TIME
PROGRAMMED message will appear on the TV screen.
Return to the incorrect program and program it with the
correct time.
® If you had entered a past date, timer recording will be
performed on that date of the next year.
® Additional programs may be entered by repeating steps
1_12.
CaMe Users: if your cable hookup is via a TV
converter box, you can program multiple recordings only on
the converter box output channel. This is because the converter determines what channel you view through your
DVD/VCR Receiver.
Tip
if you have finished
DVD/VCR Receiver
MAKE SURE YOU
DVD/VCR Receiver.
3 Use _/_ to select a program you want to check or
erase. If you want to erase the program, press
CLEAR.
4 Press MENU to return to the TV screen=
Program
Priority
If the starting
7:00PM
8:00PM
I
I
and ending
9:00PM
10:00PM
I
I
........
portions
of two or more
will
,,.......
timer
recordings overlap on the
same day, priority
the earliest
........
These
times
example,
is given
recording=
in the diagram
to
For
at
left PROGRAM
2 will not be
recorded untiI PROGRAM
1
notbe recorded,
iS finished. The first part of
PROGRAM
2 wilI not be recorded= Likewise,
PROGRAM 3 will not be recorded until PROGRAM
2 is finished,
and so on=
programming and you want to set the
to record the programs you have entered,
HAVE INSERTED A TAPE mNTOTHE
The DVD/VCR Receiver is now set to
record the preset programs.
I
I
Instant Timer Recording
Dubbing
Instant Timer Recording
easily of a preset length
ble timer.
If you wish to edit or dub your camcorder
(or another
VCR) recordings
to this DVDNCR
Receiver, the rear
(or Front) panel mounted Audio and Video (A/V) input
jacks make the connections
quick and easy. These
direct AN jacks will also provide better picture results
than using the RF jack on the rear panel.
allows you to make a recording
without using the programma-
Preparation:
• Turn on the power of both the DVDNCR Receiver and the TV.
• Be sure the TV is tuned to the DVDNCR Receiver output channel
(CH3 or 4).
• If a direct VIDEO/AUDIO connection is made between the
DVDNCR Receiver and the TV, set the TV's source selector to
VIDEO.
1. Insert a video cassette with the safety tab intact.
1. Connect the camcorder's (or another VCR's) A/V
outputs to your DVD/VCR Receiver as illustrated on
page 14.
2. Select the input channel "LINE2"
select LINE2(L2)).
2. Select the desired channel with CH/TRK (&/_') or
number (0-9) buttons.
The channel number appears on the TV screen.
• If you are recording from another source via audio/video
input jacks (at the Rear or Front panel), select
LINEI(L1) or LINE2(L2).
3.
Play the tape in the camcorder (or another VCR).
If you have a TV attached to your DVD/VCR
Receiver, you can see the video playing.
4.
When you desire the
DVD/VCR
Receiver's
The tape speed will appear on the TV screen.
Press REC/ITR (O) twice.
The menu as illustrated, will appear on the TV screen.
• Recording will start. (The G indicator will light)
5.
Press REC/ITR (O) repeatedly to select the
recording time length.
At the end of the recording, the DVD/VCR Receiver
will stop recording and shut off.
• During Instant Timer Recording, changing the channel
on the DVD/VCR Receiver will not be possible.
• Youcan stop the recording by pressing STOP.
• Each additional press or REC/ITR(O) increases recording time by 30 minutes until you reach a maximum of 9
hours.
Checking
the Recording
Time
You can stop the recording by pressing STOP.
Before recording, please confirm the recording start position.
Copying
• If you press PAUSE/STEP during instant timer recording, the
DVDNCR Receiver will enter the recording pause mode.
Instant timer recording is cancelled.
• If the DVDNCR Receiver is set to "OHOOM", the DVDNCR
Receiver goes to normal recording mode.
• The unauthorized recording, use, distribution, or revision of
television programs, videotapes, DVDs and other materials,
is prohibited under the Copyright Laws of the United States
and other countries, and may subject you to civil and/or
criminal liability.
from
DVD to VCR
This unit allows you to copy the contents of a DVD to a
VHS tape.
Press DVD/CD to select DVD mode.
1.
Insert Disc
Insert the disc you wish to copy in the DVD deck
and close the disc tray.
2.
Insert VHS Tape
Insert a blank VHS video tape into the VCR deck.
3.
Press COPY button on the unit front panel or
press REC/ITR (O) button on the remote control.
The DVD will go into Play mode and the VCR will go
into Record mode.
To extend the Recording Time
Notes
recording
to begin, press
REC/ITR (O) once to start.
Note
Press REC/ITR (O) once to check the recording
time.
The recalled setting will automatically
return to the TV
screen after 6 seconds.
The recording
time can be extended anytime by pressing REC/ITR (O).
Subsequent
presses result in advancing
the recording
time by 30-minute
increments.
(Use INPUT to
If you have connected your DVD/VCR Receiver to the A/V
input jacks on the rear of DVD/VCR Receiver, you should
select the input channel LINEI(L1) by pressing INPUT
twice.
3. Select the desired recording speed (SP or SLP)
with the SP/SLP button.
4.
and Editing
• If the DVD disc menu appears, you may need to press
PLAY manually to begin copying.
• "COPY" indicator will light.
4.
Stopping
the Copy Process
When the DVD is finished playing, press STOP to end
copying.
You must stop the Copy process manually when the DVD
movie ends, or the unit may replay and record over and
over again.
Notes
• If the DVD you are attempting to copy is copy protected, you
will not be able to copy the disc. It is not permitted to copy
Macrovision encoded DVDs. "LOCK" is displayed in the display window.
• When you stop the DVD playback during copying, VCR
recording mode also stops automatically.
• You must set Progressive Scan to Off to copy process.
MTS (Multi-Channe_
VHS Hi-F__
MTS Broadcast
This DVD/VCR Receiver is equipped with the VHS Hi-Fi
audio sound system for recording and playback. The
information below gives a brief description of Hi-Fi audio
and how to record and play a tape in the Hi-Fi audio
mode.
Mu_tichannel
Playback
with HFFi Stereo Audio Sound
A stereo TV with AUDIO/VIDEO input jacks or a stereo
audio system is required for true stereo playback. To
experience the full and rich stereo sound availabie with
Hi-Fi recorded tapes, we recommend the connection of
this unit to a home stereo audio system.
1. Set the AUDIO MODE option
SETUP menu.
TV Sound)
This DVD/VCR Receiver will decode MTS stereo and
bilingual (SAP) off-the-air broadcast sound signals. It
also decodes stereo TV sound from local cable companies, as long as they operate on assigned cable frequencies and use the EIA-recommended MTS
stereo/bilinguai TV sound system.
TV Sound
mndicator (MTS)
Shows onscreen as illustrated below when ENTER is
pressed.
® One or both of the indicators will light, depending on the
MTS broadcast.
TV screen
I
to NI-F_ on the
r
Lights up when a stereo broadcast
STEREO/SAP
is
being received.
CH 4 "?_1111
STEREO
SAP
II Lights up when a SAP BILINGUAL
I broadcast is being received.
L
_f onmy STEREO appears on the TV screen.
The DVD/VCR Receiver can record in stereo onto the VHS HiFi audio tracks when the BROADCAST TYPE option is in the
STEREO position. The DVD/VCR Receiver will also record
mono audio onto the mono audio track.
Set the AUDIO
OUTPUT
option
to STEREO
position.
STEREO: The left channel sound (L) is heard from the left
speaker and the right channel sound (R) is heard from the
right speaker,
LEFT: The left channel sound (L) is heard from both
speakers,
RmGRT: The right channel sound (R) is heard from both
speakers,
_f onmy SAP appears
on the TV screen.
Set the BROADCAST TYPE option to SAP,
_f STEREO/SAP
appears
on the TV screen
Use the BROADCAST TYPE option to select the desired
recording mode (STEREO or SAP),
SAP (Second
Audio
Program) Recording
Some stations transmit a Second Audio Program, which
is used for a second language or additional information.
When the station broadcasts a Second Audio Program,
follow the procedure below to record the SAP.
1. Insert a video cassette
with the safety tab intact,
2. Set the BROADCAST TYPE option to SAP
(SETUP menu).
Do this if only the SAP appears on the TV screen or you
know the program will use the SAP
3. Press r-_ENU.
4. insert a cassette and press PLAY.
Adjust volume at your stereo system,
3.
Press r-_ENU.
4. Select the desired recording
with the SP/SLP button.
5. Select the desired channel
on the TV screen,
speed (SP or SLP)
SAP shoumd appear
6.
Press REC/ITR (@) once
You are now recording the program you see and hear on the
TV.
7.
Press STOP to stop recording.
Tape Counter Memory Feature
Additional
Real-Time Counter
•
In manual recording, Timer recording, Instant Timer
Recording, playback, or fast forward modes, the DVDNCR
Receiver automatically starts rewinding the tape at the end
of the tape. The cassette will stop at the beginning of the
tape and be ejected, and the DVD/VCR Receiver will turn
itself off.
•
After you have finished using the DVD/VCR Receiver,
rewind, eject, and remove the cassette. Place the cassette
in its protective sleeve to protect it from dust. It is not necessary to rewind the cassette before removing it, but if you
do, it will be ready to play or record the next time you use it.
•
Be sure the DVD/VCR Receiver Channel Selector is on the
Shows length of tape run in hours, minutes,
and
seconds.
Press CLK/CNT
to select the real-time
counter
display.
Every press of CLK/CNT
illustrated
below.
CLOCK
•
•
•
changes
the TV screen
COUNTER
as
REMAINING TIME
Counter changes to "0:00:00" when the cassette is
ejected.
The real-time counter does not operate if nothing is
recorded on the tape.
The real-time counter will not work unless a tape is
inserted.
Note
During the "L1 OPT" mode, the OSD(On Screen
Display) can not be changed.
Information
correct channel you wish to record. The channel that is
being recorded can always be checked by tuning the television to the DVD/VCR Receiver channel (3 or 4) and pressing the VCR button to set the DVDNCR Receiver to VCR
mode (VCR appears in the display window).
•
Do not attempt to hook up more than one television set to
the DVD/VCR Receiver for either recording or playback.
Auto Play System
This DVD/VCR
Receiver
features
automatic
playback.
Counter Memory Feature
Load a cassette (with the safety tab removed).
• The Output Source is changed to VCR mode automatically.
This is useful if there is a section
view immediately
after recording
of tape you want to
or if you want to return
•
The power turns on automatically
•
At the end of the tape, the DVDNCR
rewinds the tape.
a tape.
•
The cassette is ejected after rewinding
itself off automatically.
to the same
point several
recording
times.
1.
Begin
or playing
2.
Press CLK/CNT
repeatedly
to display
real-time
counter
on the TV screen.
and playback begins.
Receiver stops and
and the VCR turns
the
3. At the point that you want to locate later, reset
the real-time counter to "0:00:00" by pressing
CLEAR.
4.
Continue
to play or record.
5.
Press STOP when recording or playback
finishes.
6.
Press REW (44).
The tape automatically stops when the tape counter
returns to about "0:00:00".
Note
Tape Remaining
This function
during
Press
displays
shows
recording
CLK/CNT
the remaining
time on the tape
or playback.
repeatedly
on the TV screen
until the REM
during
recording
indicator
or playback.
Note
The remaining tape length indicator may not be displayed
correctly depending on the condition of the tape and the kind of
the tape (T-140, T-160, or T-210 etc)
Auto power off does not function during regular DVD play
mode. (DVD/VCR Receiver power stays on.)
S-VHS
Quasi Playback
(SQPB)
•
This DVD/VCR Receiver can also play back a tape which is
recorded in S-VHS playback picture.
•
This DVDNCR
•
SQPB is an abbreviation
Receiver cannot record in S-VHS format
for S-VHS Quasi Playback.
Playing DVD and Video CD
Playback
Setup
|
_
• Turn on the TV and select the video input source connected
to the DVDNCR Receiver.
• Audio system: Turn on the audio system and select the input
source connected to the DVDNCR Receiver.
• Set the Output Source to DVD as shown in "Selecting the
Input/Output Source" on page 15.
1.
Press OPEN/CLOSE
( "_ ) to open the disc tray.
2. Load your chosen disc in the tray, with the label
facing up.
When a double-sided DVD is inserted, make sure
the side you want to play is facing down.
3. Press OPEN/CLOSE (_) to close the tray.
"READING" appears in the display window, and
playback starts automatically. If playback does not
start, press PLAY.
In some cases, the disc menu might appear instead.
If a menu screen is displayed
A menu screen may appear automatically
DVD.
after loading a
" i_vjm],,p
Use 4/l_/&/_' buttons to select the title/chapter you
want to view, then press ENTER to start
playback.
Press TOP MENU or DISC MENU to return to the menu
screen.
• Use the number buttons to select the track you want
to view.
Press RETURN to return to the menu screen.
• Menu setting and the exact operating procedures for
using the menu may differ depending on the disc.
Follow the instructions on the each menu screen.
You also may set PBC to Off under setup. See page
22.
Notes
• If Parental Control is set and the disc is not within the
Rating settings (not authorized), the 4-digit password
must be entered and/or the disc must be authorized
(see Parental Control, on page 23).
• DVDs may have a Region Code.
Your DVDNCR Receiver will not play discs that have
a Region Code different from your DVDNCR
Receiver. The Region Code for this DVDNCR
Receiver is 1 (one).
• Do not keep a fixed image displayed on the screen
for a long time.
General Features
Note
Unless stated otherwise, all operations described use
the remote control. Some features may also be
available on the Setup menu.
Moving
to another
TITLE
If a disc has more than one title, you can move to
another title as follows:
• Press DISPLAY, then press the appropriate number
buttons (0-9) to select a title number.
Moving
to another
CHAPTER/TRACK
If a title on a disc has more than one chapter or a disc
has more than one track, you can move to another
chapter/track as follows:
• Press SKIP (t4,4) or (1_1) briefly during playback to
return to the beginning of the current chapter/track or
to select the next chapter/track.
• Press SKIP (t4"4) twice in quick succession to step
back to the previous chapter/track.
• To go directly to any chapter/track during playback,
press DISPLAY. Use A/T to select Chapter/track icon.
Then, enter the chapter/track number with the number
buttons (0-9).
Note
For two-digit numbers, press the numbered buttons
(0-9) in rapid succession.
Slow
Motion
|
_
1 Press SLOW during playback or still mode.
The player will enter SLOW mode.
2 Use nEW or FWD (or SLOW) to select the required
speed:
41 1/16, 41 1/8, 41 1/4, 41 1/2 (backward), or
I1_ 1/16, I1_ 1/8, I1_ 1/4, liD,1/2 (forward).
3 To return to playback, press PLAY.
Note
Slow motion playback in reverse is not applicable for
Video CD.
Still Picture
and Frame-by-Frame
Playback
1 Press PAUSE!STEP during playback.
The DVDNCR Receiver will go into PAUSE mode.
2 You can advance the picture frame by frame by
pressing PAUSE/STEP repeatedly on the remote control.
3 To return to playback, press PLAY.
General
Search
_
Features
(Continued)
_
Repeat A-B
1 Press REW (_t_1) or FWD (1=,,_)during playback.
The DVDNCR Receiver will now go into SEARCH mode.
2 Each press of the REW (_t_1) or FWD (1=,,_)button
will increase the speed of the search _t_IX2, _t_IX4,
_t_IX16, _t_IX100 (backward) or I=,,-I_X2,I=,,-I_X4,
I=,,_X16, I=,,_X100 (forward).
With a Video CD, the Search speed changes: _t_IX2,
_t_IX4, _t_IX8, (backward) or I=,,_X2, I=,,_X4, I=,,_X8,
(forward).
3 To return to playback, press PLAY.
To repeat a sequence in a title:
Random
This unit can produce a 3D Surround effect,
simulates multi-channel audio playback from
conventional stereo speakers, instead of the
more speakers normally required to listen to
channel audio from a home theater system.
1 Press RANDOM during playback or in Stop mode.
The unit automatically begins Random Playback and
"RANDOM" appears on the TV screen.
2 To return to normal playback, press RANDOM until
"NORMAL" appears on the TV screen.
Tips
By pressing SKIP (1_t_1 or I_N) during Random playback, the unit selects another title (track) and resumes
Random playback.
Notes
• This function only works with DVD Karaoke discs and
Video CD without PBC.
• On a Video CD with PBC, you must set PBC to Off on
the setup menu to use the Random function. See
page 22.
Repeat _
_)
DVD Video Discs - Repeat Chapter/Title/Off
1 To repeat the currently playing chapter, press
REPEAT.
The Repeat Chapter icon appears on the TV screen.
2 To repeat the title currently playing, press REPEAT a
second time.
The Repeat Title icon appears on the TV screen.
3 To exit Repeat mode, press REPEAT a third time.
The Repeat Off icon appears on the TV screen.
Video CDs - Repeat Track/All/Off
1 To repeat the track currently playing, press REPEAT.
The Repeat Track icon appears on the TV screen.
2 To repeat the disc currently playing, press REPEAT a
second time.
The Repeat All icon appears on the TV screen.
3 To exit Repeat mode, press REPEAT a third time.
The Repeat Off icon appears on the TV screen.
Note
On a Video CD with PBC, you must set PBC to Off on the
setup menu to use the Repeat function. See page 22.
1 Press REPEAT A-B at your chosen start point.
"A * " appears briefly on the TV screen.
2 Press REPEAT A-B again at your chosen end point.
"A B" appears briefly on the TV screen, and the repeat
sequence begins.
3 To cancel the sequence, press REPEAT A-B.
3D Surround
which
two
five or
multi-
1 Press SOUND MODE to select "3D SUR" during
playback.
2 To turn off the 3D Surround effect,
press SOUND MODE again to select "BYPASS".
Time Search
_
_:_:_;
.....
; .........
:::::
The Time Search function allows you to start playing at
any chosen time on the disc.
1 Press DISPLAY during playback. The on-screen display appears on the screen.
The Time Search box shows the elapsed playing time of the
current disc.
2 Within 10 seconds, use A/T to select the Time
Search icon in the on-screen display.
The "-:--:--" appears in the Time Search box.
3 Within 10 seconds, use the numbered buttons to
enter the required start time. Enter hours, minutes
and seconds from left to right in the box.
If you enter the wrong numbers, press CLEAR to remove the
numbers you entered. Then enter the correct numbers.
4 Within 10 seconds, press ENTER.
Playback starts from the selected time on the disc. If you
enter an invalid time, playback will continue from the current
point.
Zoom
The Zoom function allows you to enlarge the video
image and to move through the enlarged image.
1 Press ZOOM during playback or still playback to activate the Zoom function.
If you press ZOOM repeatedly, the magnification level
increases up to six steps.
2 Use _l/l_/&/_' buttons to move through the zoomed
picture.
3 Press CLEAR to resume normal playback or return to
the paused image.
Notes
• The Zoom function may not work with some DVDs.
• The Zoom function may not work with some
multi-angle scenes.
General
Features (Continued)
Special DVD Features
Checking
Marker Search
discs:
You can start playback from a memorized point. Up to
nine points can be memorized.
To enter a mark, follow these steps.
1 During disc playback, press MARKER when playback
reaches the spot that you want to memorize.
The Marker icon will appear on the TV screen briefly.
2 Repeat step 1 to enter up to nine Marker points on a
disc.
To Recall a Marked Scene
Menus
DVDs may contain menus that allow you to access special features. To use the disc menu, press DISC MENU.
Then, press the appropriate number button to select an
option. Or, use 4/l_/&/_' buttons to highlight your selection, then press ENTER.
Title Menu
1 Press TOP MENU.
3 To remove the title menu, press TOP MENU again.
Disc Menu
1 Press DISC MENU.
1 During disc playback, press SEARCH.
The Marker Search menu will appear on the screen.
2 Within 10 seconds, use 4_ or number button to
select a Marker number that you want to erase.
3 Press CLEAR.
The Marker number will be erased from the list.
4 Repeat steps 2 and 3 to erase additional Marker
numbers.
5 To remove the MARKER SEARCH menu, press
SEARCH.
• All markers are erased when the disc is ejected.
The disc menu is displayed.
2 To remove the disc menu, press DISC MENU again.
Camera Angle
If the disc contains sequences recorded from different
camera angles, the angle icon appears for a short while
on the TV screen. You can then change the camera
angle if you wish.
• Press ANGLE repeatedly during playback to select a
desired angle.
The number of the current angle appears on the display.
Video Mode
• With certain discs, the playback picture may be flickering or Dot Crawl is shown on straight lines. That
means Vertical interpolation or De-interlace is not
perfectly matched with the disc. In this case, the
picture quality may be improved by changing the
video mode.
• To change the video mode, press and hold
DISPLAY about 3 seconds during disc playback. The
new video mode selected is displayed on the TV
screen. Check whether the video quality has
improved. If not, repeat the above procedure until picture quality is improved.
• Video mode sequence:
Auto -_ Film -_ Video -_ Auto
• If you turn off the power, the video mode will return to
initial default state (Auto).
Detailed Description
of each Video Mode
Auto : The source material of the DVD video (film material or
video material) is determined from disc information.
Film : Suitable for playing film based content or video based
material recorded by the progressive scan method.
Video : Suitable for playing video based content with
comparatively little motion.
Changing the Audio Language
i
i_
i
EN_
DDO
Press AUDIO repeatedly during playback to hear a
different audio language or audio track.
Changing
the Audio Channel
Press AUDIO repeatedly during playback to hear a different audio channel (STER., LEFT or RIGHT).
Subtitles
_
,
i
Press SUBTITLE repeatedly during playback to see the
different subtitle languages.
Note
If Q appears, the feature is not available on the disc.
Screen Saver
Note
The video mode setting only works when the Progressive
mode is set to "On" in the Setup menu.
of DVD Video
If the current title has a menu, the menu will appear on the
screen. Otherwise, the disc menu may appear.
2 The menu can list camera angles, spoken language
and subtitle options, and chapters for the title.
1 During disc playback, press SEARCH.
The Marker Search menu will appear on the screen.
2 Within 10 seconds, use 4/I, or number button to
select a Marker number that you want to recall.
3 Press ENTER.
Playback will start from the Marked scene.
4 To remove the MARKER SEARCH menu, press
SEARCH.
To Clear a Marked Scene
Changing
the contents
Scan
The screen saver picture appears when you leave the
DVDNCR Receiver in Stop mode for about five minutes.
Playingan Audio CD and MP3NVMA
Notes on MP3/WMA Recordings
Discs
About
The DVD/VCR Receiver can play MP3/WMA formatted
recordings on CD-ROM, CD-R or CD-RW discs.
Before playing MP3/WMA discs, read the notes on
MP3/WMA Recordings on right.
Insert a disc and close the tray.
Audio CD: Audio CD menu appears on the TV
screen. Go to step 4.
MP3/WMA disc: The MP3/WMA-JPEG choice menu
appears on the TV screen. Go to step 2.
Use _
to select the MP3/WMA then press
ENTER.
The MP3/WMA menu appears on the TV screen.
Press RETURN to move to the MP3/WMA-JPEG
choice menu.
3.
Use _
to select a folder then press ENTER.
A list of files in the folder appears.
4.
Use _
to select a track then press PLAY or
ENTER.
Playback starts.
During playback, the current track's elapsed playing
time will appear on the display window and menu.
Playback will stop at the end of the disc.
Press TOP MENU to move to the next page.
Press DISC MENU to move to the previous page.
Audio CD Menu
MP3/WMA Menu
Tip
If you are in a File List and want to return to the Folder
List, use the _
to highlight -. and press ENTER to
return to the previous menu screen.
5. To stop playback at any other time, press
STOP.
•
•
About
•
•
MP3
An MP3 file is audio data compressed by using the
MPEG1 audio layer-3 file-coding scheme. We call
files that have the ".rap3" file extension "MP3 files".
The DVD/VCR Receiver can not read an MP3 file
that has a file extension other than ".mp3".
WMA
(Windows
Media
Audio)
Files
An WMA file is a Microsoft audio compression
technology.
WMA(Windows Media Audio) offers double audio
compression of the MP3 format.
MP3/WMA
Disc compatibility
with this player is
limited as follows:
1. Sampling Frequency/only
at 44.1kHz (MP3),
22.05 - 44.1 kHz (WMA)
2. Bit rate / within 32 - 320kbps (MP3),
32 - 128kbps (WMA)
3. CD-R physical format should be "ISO 9660"
4. If you record MP3/WMA files using the software
which cannot create a FILE SYSTEM, for example
"Direct-CD" etc., it is impossible to playback
MP3/WMA files. We recommend that you use "EasyCD Creator", which creates an ISO9660 file system.
5. A single session disc requires MP3/WMA files in the
first track. If there is no MP3/WMA file in the 1st
track, it cannot playback MP3/WMA files. If you wish
to playback MP3/WMA files, format all the data in
the disc or use a new one.
6. File names should be named using 8 letters or less
and must incorporate ".mp3" or ".wma" extension
e.g. '......... .MP3" or .......... .WMA".
7. Do not use special letters such as "/: * ? " < >" etc.
8. Total number of files on the disc should be less than
650.
This DVDNCR Receiver requires discs/recordings to
meet certain technical standards in order to achieve
optimal playback quality. Pre-recorded DVDs are automatically set to these standards. There are many different types of recordable disc formats (including CD-R
containing MP3/WMA files). Because this area of technology is still evolving, Toshiba cannot guarantee that
all recordable discs will produce optimal playback quality. The technical criteria set forth in this owner's manual
are meant only as a guide.
Please be advised that you must obtain permission
from the applicable copyright owners to download
copyrighted content, including music files, in any
format, including the MP3 and WMA formats, prior
to the downloading thereof. Toshiba has no right to
grant and does not grant permission top download
any copyrighted content.
Microsoft, Windows Media, and the
Windows Logo are trademarks or
registered trademarks of Microsoft
Corporation in both the United States
and other countries
Windows
Designed for
I
I
Pause ql_D ql_
qi_
Repeat A-B
1 Press PAUSE/STEP during playback.
2 To return to playback, press PLAY or press
PAUSE/STEP again.
Moving to another Tracks qI_DC]_)(_)
• Press SKIP (14<1 or IH_I) briefly during playback to
go to the next track or to return to the beginning of
the current track.
• Press SKIP (144) twice in quick succession to step
back to the previous track.
• On Audio CDs, to go directly to any track, enter the
track number using the numbered buttons (0-9) during playback.
Search
ql_D
ql_D qi_;_
1 Press REW (44) or FWD (ll,,-I_) during playback.
The player will now go into SEARCH mode.
2 Each press of the REW (4<1) or FWD (1=,,_)button
will increase the speed of the search <t<IX2, <t<IX4,
<t4X8 (backward) or I=,,_X2, I=,,_X4, I=,,_X8 (forward).
Search speed and direction are indicated on the menu
screen.
3 To exit SEARCH mode, press PLAY.
Random
tied
€]_)
To repeat a sequence.
1 During disc playback, press REPEAT A-B at your chosen starting point.
The Repeat icon and "A * " appears on the menu screen.
2 Press REPEAT A-B again at your chosen end point.
The Repeat icon and "A B" appears on the menu screen,
and the sequence begins to play repeatedly.
3 To exit the sequence and return to normal play, press
REPEAT A-B again.
The Repeat icon and "OFF" appears on the menu screen.
3D Surround
|
This unit can produce a 3D Surround effect, which
simulates multi-channel audio playback from two
conventional stereo speakers, instead of the five or
more speakers normally required to listen to multichannel audio from a home theater system.
1 Press SOUND MODE to select "3D SUR"
during playback.
2 To turn off the 3D Surround effect,
press SOUND MODE again to select "BYPASS".
Changing
the Audio Channel
Press AUDIO repeatedly during playback to hear a
different audio channel (STER., LEFT, or RIGHT).
4_:_
1 Press RANDOM during playback or in Stop mode.
The unit automatically begins Random Playback and
"RAND." appears on the menu screen.
2 To return to normal playback, press RANDOM repeatedly until "RAND." disappears from the menu screen.
Note
RANDOM only works in File List of MP3 and WMA
discs.
Repeat Track/All/Off
qB_lDql:_)(_
1 To repeat the track currently playing, press REPEAT.
The Repeat icon and "TRACK" appears on the menu
screen.
2 To repeat all tracks on a disc, press REPEAT a second time.
The Repeat icon and "ALL" appears on the menu screen.
3 To cancel Repeat mode, press REPEAT a third time.
The Repeat icon and "OFF" appears on the menu screen.
m
m
I
I
Viewing JPEG Files on a Disc
This DVDNCR Receiver can play discs with JPEG files.
Before playing JPEG files, read the notes on JPEG
Files on right.
1. Insert a disc and close the tray.
The MP3/WMA-JPEG choice menu appears on the
TV screen.
Selecting
other Files
Press SKIP (1_1 or I_1_1) once while viewing a picture
to advance to the next file or to the previous file.
Still Picture
1 Press PAUSE/STEP during slide show.
The player will now go into PAUSE mode.
2 To return to the slide show, press PLAY or press
PAUSE/STEP again.
To flip the picture
2.
Use A/V to select the JPEG then press ENTER.
The JPEG menu appears on the TV screen.
Press A/T while showing a picture to flip the
picture horizontally or a vertically.
To rotate picture
Press _/1_ while showing a picture to rotate the
picture clockwise or counter clockwise.
Notes on JPEG Files
Use _
to select a folder, and ENTER.
A list of files in the folder appears.
Press RETURN to move to the MP3/WMA-JPEG
choice menu.
Tip
If you are in a file list and want to return to the Folder
list, use the AT buttons on the remote to highlight
" cJ.." and press ENTER to return to the
previous menu screen.
If you want to view a particular file, use _
to
highlight the file and press ENTER or PLAY.
Viewing the file function starts.
While viewing a file, press RETURN to move to the
previous menu (JPEG menu).
Press TOP MENU to move to the next page.
Press DISC MENU to move to the previous page.
Tip
There are three viewing Slide Speed options: Fast,
Normal, Slow, and Off. Use _/_ to highlight the Slide
Speed then use A/v to select the option you want to
use, and press ENTER.
5. To stop viewing at any other time, press STOP.
The JPEG menu appears.
• Depending upon the size and number of the JPEG
files, it could take a long time for the DVD player to
read the disc's contents. If you don't see an onscreen display after several minutes, some of the files
are too big -- reduce the resolution of the JPEG files
to less than 3072x2048 pixels and burn another disc.
• Total number of files and folders on the disc should
be less than 650.
• Some disc may be incompatible due to different
recording format or condition of disc.
• When you are using software such as "Easy CD
Creator" to burn the jpeg files into the CD-R, ensure
that all the selected files have the ".jpg" extensions
when copying into the CD layout.
• If the files have ".jpe" or ".jpeg" extensions, please
rename them as ".jpg" files.
• File names without ".jpg" extension will not be able to
be read by this DVD/VCR Receiver, even though the
files are shown as JPEG image files in windows
explorer.
I
I
Programmed
Playback
and MP3/WMA
with Audio CDs
Discs
The Program function enables you to store your
favourite tracks from any disc in the player memory.
Program can contain 30 tracks.
1. Press
mode
The []
on the
Programmed
Playback
with Video CD
Note
On a Video CD with PBC, you must set PBC to Off on the
setup menu to use the Program function. See page 22.
1. Insert Video CD and close the tray.
2. Press PROGRAM while playback
The VCD Program menu will appear.
is stopped.
PROGRAM during playback or in the Stop
to enter the Program Edit mode.
mark will appear to the right of the word Program
right side of the menu screen.
Note
Press PROGRAM to exit the Program Edit mode;
the [] mark will disappear.
Note
Press RETURN,PROGRAMor PLAYto exit the Programmenu.
2. Select a track, then press ENTER to place the
selected track on the Program list.
3. Follow steps 2-6 of "Programmed
Playback
Audio CD and MP3/WMA disc" on left.
3. Repeat step 2 to place additional tracks on the
Program list.
4.
with
Press PLAY (1=,_)or ENTER to start.
Playback begins in the order in which you programmed the
tracks. "PROGRAM" indicator will appear briefly on the TV
screen.
Playback stops after all of the tracks on the Program list
have played once.
5. To resume normal playback
from
programmed
playbacl_, press PROGRAM.
"NORMAL" indicator will appear briefly on the TV screen.
Audio CD menu
MP3/WMA
menu
4. Press •.
The programmed track you selected last is highlighted on
the program list.
5. Use _
to select the track you want to start
playing.
Press TOP MENU to move to the next page.
Press DISC MENU to move to the previous page.
6. Press PLAY or ENTER to start.
Playback begins in the order in which you programmed the
tracks and "PROG." appears on the menu screen.
Playback stops after all of the tracks on the Program list
have played once.
7. To resume normal playback from programmed
playback, press PROGRAM.
Select a track of CD (or MP3/WMA) list and then
press ENTER or PLAY.
"PROG" indicator disappears from the display window.
Repeat Programmed
Tracks
• To repeat the track currently playing, press REPEAT.
The Repeat icon and "TRACK" appears on the menu screen.
• To repeat all tracks on the program list, press
REPEAT a second time.
The Repeat icon and "ALL" appears on the menu screen.
• To cancel Repeat mode, press REPEAT a third time.
The Repeat icon and "OFF" appears on the menu screen.
Note
For Video CD, the Repeat icon will only appear briefly on the
screen.
Erasing a Track from Program List
1 Press PROGRAM during playback (Audio CD and
MP3/WMA disc only) or stop to enter the Program
Edit mode.
The [] mark will appear.
2 Press • to move to the Program list.
3 Use A/V to select the track that you wish to erase
from the Program list.
4 Press CLEAR.
The track will be erased from the Program list.
Erasing the whole Program List
1 Follow steps 1-2 of "Erasing a Track from Program
List" as above.
2 Use _
to select "Clear All", then press ENTER.
The complete Program for the disc will be erased.
Notes
• The programs are cleared when the disc is removed.
• The programs are cleared when another function mode
(VCR, radio etc.) is selected.
m
m
I
I
I
I
Adjust the following settings for the built-in 5.1 channel
surround decoder.
Distance
If you connected speakers to your DVD/VCR Receiver,
setting the Distance lets the speakers know how far the
sound has to travel to reach your set listening point.
This allows the sound from each speaker to reach the
listener at the same time. (1-20 ft, 1 ft = 0.30 m)
Note
You can not set the distance of subwoofer speaker.
Test
1. Select "5.1 Speaker Setup" using the A/V
buttons on the setup menu.
2. While "5.1 Speaker Setup" is selected, press •
button.
3.
Press ENTER to test the signals of each speaker.
Adjust the volume to match the volume of test signals
memorized in the system.
• Front Left (L) -_ Centre -_ Front Right (R) -_
Rear Right (R) -_ Rear Left (L) -_ Subwoofer
Press I_ buttons to select the desired speaker.
4. Adjust options by using AT4
I_ buttons.
Return
Press ENTER to return to the previous menu.
Speaker
selection
Select a speaker that you want to adjust. ((Front speakers (Left), Centre Speaker, Front speakers (Right), Rear
speakers (Left), Rear speakers (Right), or Subwoofer))
Note
Certain speaker settings are prohibited by the Dolby
Digital licensing agreement.
Volume
Press 4 / I_ to adjust the output level of the selected
speaker. (-6dB - 6dB)
Size
Since the speaker settings are fixed, you cannot
change the settings.
•
Subwoofer's
size is fixed "Large" and the other
speaker's size are fixed "small".
m
I
I
I
I
Presetting the Radio Stations
Listening to the Radio
You can preset 50 stations for FM and AM. Before tuning, make sure that you have turned clown the volume.
Preset radio stations in the DVDNCR Receiver memory
first (see "Presetting Radio Stations" on the left).
1. Press FM/AM on the remote
1.
control
the front panel until the frequency
on the display and TV screen.
or RADIO on
band appears
Press FM/AM on the remote control or RADIO on
the front panel until the frequency band appears
on the display and TV screen.
The last received station is tuned in.
2.
AM
AM
_720kHz
600kHz
AM
AM
1400kHz
lO00kHz
Use A/V on the remote control repeatedly to
select the preset station you want.
Each timeyou press the button, the DVDNCR Receiver
tunes in one preset station at a time.
3. Adjust the volume by rotating VOLUME on the
front panel or by pressing VOLUME (A or T) on
the remote control repeatedly.
Use A_' on the remote control or
CH/PRESET (/_ / _/) front panel to select the
desired Station.
If you select a blank column, R-SKIP appears in the
display window.
To Clear the Stored Radio Stations
1.
Press FM/AM on the remote control or on the
front panel until the frequency
the display and TV screen.
FM
band appears on
87.5MHz
...._'_'!_'_
_i_.' '_i _" "' _iI !'!'_?'i_ii'_'"':
ii
FM 106. OMHz
FM
98,0MHz
AM
AM
AM
3.
Press FM/AM on the remote control or front
panel to select the desired band.
2.
4. Hold down TUNING (/_,/V)
on the front panel or
TUNING (A/V) remote control for 1 or 2 seconds,
and a station is searched for automatically.
/_1_1_
600kHz
1400kHz
Use A/_' on the remote control to select your
desired station.
FM
Press MEMORY on the remote control.
The station is stored.
1720kHz
FM
87.5MHz
106.0MHz
\
3.
6. Repeat steps 2 to 5 to store other stations.
Press CLEAR the remote control to clear the
stored radio station.
FM 87. OMHz
Note
While record or record pause mode, the CLEAR
function may not be operated.
m
m
I
I
I
I
Tuning into a Station Manually
1. Press FM/AM on the remote control until the frequency band appears on the display and TV
screen.
2.
Press FM/AM on the remote control to select the
desired band.
3.
Press TUNING (JJv) on the remote control to
tune in the desired station.
For your reference
Weak FM stations
"ST" may flash when a weak FM stereo signal is
received, select another station or realign the antenna.
To turn off the radio
Press POWER (I/V) to turn the DVD/VCR Receiver off
or select another function mode (DVD or VCR).
Tuning into a Station Automatically
Hold down TUNING (A/V) on the remote control for 1
or 2 seconds, and a station is searched for automatically.
Note
The search may not stop at a station with a very weak
signal.
Labeling Stations
1. Press •
to move to the station name column.
FM
87 : 5MHz
FM
98.0MHz
Use the A/V buttons to select the character then
use the <_ buttons to shift to the next or previous character.
3.
4.
Press ENTER to confirm the station name.
Press ENTER on the remote control.
The station name is stored.
m
I
I
I
I
The remote control can be compatible with various
brands of TV by setting their control codes. The TOSHIBA code has initially been set to control TOSHIBA TVs.
TV POWER
TV
POWER
Setting
TV Control
Codes
POWER
C3 C3 C3
[_
VD/CD
1. Press TV to set the remote control operating
your TV.
VCR
4"
MOD_
AUX
FM/AM
INPUT
EJEOr
Ci3 E2] [?_
2. While holding down PROGRAM button, enter
the two digits of your TV's brand code (listed on
page 41) using number buttons.
--PROGRAM
3. Release PROGRAM.
By pressing
You can
TV POWER
Turn the TV on or off.
CH/TRK (V/A)
To select TV channels in the upper
or lower direction.
VOLUME (V/A)
Adjust the volume of the TV.
INPUT
Switch the TV's input source
between the TV and other input
sources.
ANGLE
SUBIITLE
AUDIO
[email protected]
@[email protected]
I UNING
SEARCH
eVOLUME
DISpLAy
SET
VOLUME
UP
CH_RK
Important
Some TV's may not respond to all the operations
above, or may not be operated at all with this
remote control. In this case, operate your TV with
its own remote control.
TV/VCR
SLOW
R
W
_
MUTE
STOP
PAUSE!STEP
FWD
SKIP
REO/ITR aEP_T_-B REPEAt
Notes
• For some brands, several control codes (brand
codes) are allocated. Try each of them until the buttons work on your TV.
• If you replace the remote control's batteries, set the
brand code again.
I
PLAY
RANDOM
_J CD C3 C_
SP/SLP
TOSHIBA
___jJ
I
Table of TV Brand Codes
Brand name of your TV
Brand Code
Toshiba
01
Bell & Howell
09
Carver
10
Celebrity
03
Brand name of your TV
Runco (NEC)
Brand Code
14
Samsung
Sanyo
Scotch
11,12
09
11
Citizen
12
Scott
11
Curtis Mathes
09, 12
Sears
01, 02, 09, 10, 11
Dumont
14
Sharp
08, 13
Electro band
03
Sony
03
Emerson
09, 11
Fisher
09
GE
02, 07, 11
Gibraiter
14
Soundesign
11
Supreme
03
Sylvania
10
08
Goldstar
11
Tandy
Hallmark
11
Technics
07, 15
Hitachi
06
Techwood
07
Infinity
10
Teknika
04, 10, 12
JBL
10
TMK
11
JCB
03
Victor
05
JVC
05
Vidikron
10
LXI
01, 02, 09, 10, 11
Vidtech
11
Magnavox
10
Wards
10, 11, 13
Marantz
10
Zenith
14
Megatron
06, 11
Memorex
04, 09, 11
MGA
04, 11
Midland
02, 07, 14
Mitsubishi
04, 11
Motorola
08
MTC
12
NAD
01, 11
Nikko
11
Optimus
09
Optonica
08
Panasonic
07, 10, 15
Penney
01, 02, 07, 11, 12
Philco
10
Philips
10
Pioneer
16
Princeclub
12
Prism
07
Proscan
02
Proton
11
Pulser
14
Quasar
07, 15
Radio Shack
13
RCA
02
Realistic
09, 11, 13
I
I
Check the following guide for the possible cause of a problem before contacting service.
Symptom
Cause
Solution
No power.
• The power cord is disconnected.
• Plug the power cord into the wall outlet
securely.
The power is on, but the
DVD/VCR Receiver
does not work.
• No disc is inserted.
• No tape is inserted,
• Insert a disc or tape. (Check that the
disc or tape indicator in the display
window is lit.)
No picture.
• The TV is not set to receive DVDNCR
Receiver signal output,
• Select the appropriate video input mode
on the TV so the picture from the
DVDNCR Receiver appears on the TV
screen.
• TVNCR mode for DVD/VCR Receiver is
set to TV MODE.
• Press the TV/VCR button on the remote
control repeatedly to choose VCR
mode. VCR MODE appears in the display window.
• The video cable is not connected
securely.
• Connect the video cable securely.
• The connected TV power is turned off.
• Turn on the TV.
• The equipment connected with the
audio cable is not set to receive
DVDNCR Receiver signal output,
• Select the correct input mode on the
audio receiver so you can listen to the
sound from the DVDNCR Receiver.
• The audio cables are not connected
securely.
• Connect the audio cable securely.
• The power of the equipment connected
with the audio cable is turned off.
• Turn on the equipment connected with
the audio cable.
• The audio connecting cord is damaged.
• Replace it with new one.
The playback picture is
• The disc is dirty.
• Clean the disc.
poor.
• Tape heads are dirty.
• Clean video heads.
• Tape is a rental or was recorded on
another VCR.
• Use CH/TRK (A/T) for manual tracking
adjustment while tape is playing.
• No disc is inserted.
• No tape is inserted,
• Insert a disc or tape. (Check that the
disc or tape indicator in the display
window is lit.)
• An unplayable disc is inserted.
• Insert a playable disc. (Check the disc
type, color system, and Regional code.)
• The disc is placed upside down.
• Place the disc with the playback side down.
• The disc is not placed within the guide.
• Place the disc on the disc tray correctly
inside the guide.
• The disc is dirty.
• Clean the disc.
• The Rating level is set.
• Cancel the Rating function or change
the rating level.
• The remote control is not pointed at the
remote sensor of the DVDNCR Receiver.
• Point the remote control at the remote
sensor of the DVD/VCR Receiver.
• The remote control is too far from the
DVDNCR Receiver.
• Operate the remote control within 23 ft
(7 m).
• There is an obstacle in the path of the
remote control and the DVDNCR
Receiver.
• Remove the obstacle.
• The batteries in the remote control are
exhausted.
• Replace the batteries with new ones.
• This remote control use the same
buttons for VCR and DVD functions
(ex. PLAY).
• When using a VCR, first press the VCR
button. When using a DVD, first press
the DVD button.
No sound.
The DVDNCR Receiver
does not start playback.
The remote control
does not work properly,
m
m
I
I
I
I
Symptom
Cause
Solution
INPUT, VOLUME (_hJ_')
and 4/_.,/Am' buttons on
remote control cannot
operate.
Some channels are
skipped over when using
CH/TRK (A/T)
Picture and sound of
broadcasting channel are
weak or missing.
• Incorrect mode (e.g. Remote control in
TV mode),
• Press DVD/CD, VCR or FM/AM to
select the correct mode on the remote
control.
• Those channels were deleted with the
CH. ADD/DEL option.
• Use CH. ADD/DEL to restore channels.
See "Channel Selection" on page 18.
• Antenna or cables are loose.
• Tighten connections
• Wrong CHANNEL SOURCE option is
being used.
• Try all CHANNEL SOURCE options.
See "Channel Selection" on page 18 for
details.
Camcorder
shown,
• Camcorder is off.
• Turn camcorder on and operate
properly.
Camcorder image via
AN input to DVDNCR
Receiver is not shown on
TV screen.
• DVDNCR Receiver INPUT SELECT is
not set to LINEI(L1) or LINE2(L2).
• Press INPUT to select LINE input channel (LINEI(L1) or LINE2(L2)).
Timer recording is not
possible,
• Clock in DVDNCR
to correct time.
• Set clock to correct time. See "Setting
the Clock" on page 19.
image is not
Receiver is not set
or replace cable.
• Timer has been programmed
incorrectly.
• Reprogram Timer. See "Timer
Recording" on pages 25 and 26.
•
• Reprogram Timer.
Q indicator light does not appear after
programming timer.
Stereo Audio Record
• TV is not Stereo-compatible.
• No action is possible.
and/or Playback is not
present,
• Broadcast program is not in stereo format.
• No action is possible.
• DVDNCR Receiver AN Out jacks are
not connected to TV AN In jacks,
• Make AN connections. Stereo is
available only via A/V output from
DVD/VCR Receiver.
• DVDNCR Receiver AudioNideo Out is
not selected for viewing at the TV.
• DVDNCR Receiver BROADCAST
TYPE mode is set to SAP or MONO.
• Select AUX or A/V source as TV input.
• The plugs and jacks are dirty.
• Wipe them with a cloth slightly moistened with alcohol.
• The disc is dirty.
• Clean the disc.
• The speakers and components are
connected poorly.
• The DVDNCR Receiver is located too
close to the TV.
• Connect the speakers and components
securely.
• The antenna is positioned or connected
poorly.
• Connect the antenna securely.
Severe hum or noise is
heard,
Radio stations cannot be
tuned in.
• Set BROADCAST TYPE mode to
STEREO. See "VCR Setup Menu
Option" on page 18.
• Move your TV away from the audio
components.
• Adjust the antennas and connect an
external antenna if necessary.
No sound from DIGITAL
AUDIO IN (OPTICAL).
I
• The signal strength of the stations is too
weak (when tuning in with automatic
tuning).
• Tune in the station manually.
• No stations have been preset or preset
stations have been cleared (when
tuning by scanning preset stations).
• Preset the stations (page 38).
• DVDNCR Receiver source is not set to
DIGITAL AUDIO IN (OPTICAL).
• Select OPTICAL by pressing AUX once.
I
I
I
Enter the appropriate code number for the initial settings "Disc Audio", "Disc Subtitle" and/or "Disc Menu"
(See page 21).
Code
Language
Code
Language
Code
Language
Code
Language
6566
Abkhazian
7074
Fiji
7678
Lingala
8373
Singhalese
6565
Afar
7073
Finnish
7684
Lithuanian
8375
Slovak
6570
Afrikaans
7082
French
7775
Macedonian
8376
Slovenian
8381
Albanian
7089
Frisian
7771
Malagasy
8379
Somali
6577
Amharic
7176
Galician
7783
Malay
6983
Spanish
6582
Arabic
7565
Georgian
7776
Malayalam
8385
Sudanese
7289
Armenian
6869
German
7784
Maltese
8387
Swahili
6583
Assamese
8976
Greek
7773
Maori
8388
Swedish
6588
Aymara
7576
Greenlandic
7782
Marathi
8478
Tagalog
6590
Azerbaijani
7178
Guarani
7779
Moldavian
8471
Tajik
6665
Bashkir
7185
Gujarati
7778
Mongolian
8465
Tamil
6985
Basque
7265
Hausa
7865
Nauru
8484
Tatar
6678
Bengali; Bangla
7387
Hebrew
7869
Nepali
8469
Telugu
6890
Bhutani
7273
Hindi
7879
Norwegian
8472
Thai
6672
Bihari
7285
Hungarian
7982
Oriya
6879
Tibetan
6682
Breton
7383
Icelandic
8065
Panjabi
8473
Tigrinya
6671
Bulgarian
7378
Indonesian
8083
Pashto, Pushto
8479
Tonga
7789
Burmese
7365
Interlingua
7065
Persian
8482
Turkish
6869
Byelorussian
7165
Irish
8076
Polish
8475
Turkmen
7577
Cambodian
7384
Italian
8084
Portuguese
8487
Twi
6765
Catalan
7465
Japanese
8185
Quechua
8575
Ukrainian
9072
Chinese
7487
Javanese
8277
Rhaeto-Romance
8582
Urdu
6779
Corsican
7578
Kannada
8279
Remanian
8590
Uzbek
7282
Croatian
7583
Kashmiri
8285
Russian
8673
Vietnamese
6783
Czech
7575
Kazakh
8377
Samoan
8879
Volap_k
6865
Danish
7589
Kirghiz
8365
Sanskrit
6789
Welsh
7878
Dutch
7579
Korean
7168
Scots Gaelic
8779
Wolof
6978
English
7585
Kurdish
8382
Serbian
8872
Xhosa
6979
Esperanto
7679
Laothian
8372
Serbo-Croatian
7473
Yiddish
6984
Estonian
7665
Latin
8378
Shona
8979
Yoruba
7079
Faeroese
7886
Latvian, Lettish
8368
Sindhi
9085
Zulu
m
m
I
I
Enter the appropriate code number for the initial setting "Area Code List" (See page 23).
Code
Area
Code
Area
Code
Area
Code
Area
AD
Andorra
ER
Eritrea
LC
Saint Lucia
SC
Seychelles
AE
United Arab Emirates
ES
Spain
LI
Liechtenstein
SD
Sudan
AF
AG
Afghanistan
Antigua and Barbuda
ET
FI
Ethiopia
Finland
LK
LR
Sri Lanka
Liberia
SE
SG
Sweden
Singapore
AI
AL
Anguilla
Albania
FJ
FK
Fiji
Falkland
LS
LT
Lesotho
Lithuania
SH
Sl
Saint Helena
Slovenia
AM
AN
Armenia
Netherlands
FM
FO
Micronesia
Faroe Islands
LU
LV
Luxembourg
Latvia
SJ
Svalbard
Islands
AO
Angola
FR
France
LY
Libya
SK
Slovak Republic
AQ
AR
Antarctica
Argentina
FX
France (European
Territory)
MA
MC
Morocco
Monaco
SL
SM
Sierra Leone
San Marino
AS
American
GA
Gabon
MD
Moldavia
SN
Senegal
AT
AU
Austria
Australia
GB
GD
Great Britain
Grenada
MG
MH
Madagascar
Marshall Islands
SO
SR
Somalia
Suriname
AW
Aruba
GE
Georgia
MK
Macedonia
ST
Saint Tome and Principe
AZ
Azerbaidjan
GF
French Guyana
ML
Mali
SU
Former USSR
BA
BB
Bosnia-Herzegovina
Barbados
GH
GI
Ghana
Gibraltar
MM
MN
Myanmar
Mongolia
SV
SY
El Salvador
Syria
BD
Bangladesh
GL
Greenland
MO
Macau
SZ
Swaziland
BE
BF
Belgium
Burkina Faso
GM
GN
Gambia
Guinea
MP
MQ
Northern Mariana Islands
Martinique (French)
TC
TD
Turks and Caicos Islands
Chad
BG
Bulgaria
GP
Guadeloupe
MR
Mauritania
TF
French Southern
BH
BI
Bahrain
Burundi
GQ
GR
Equatorial
Greece
MS
MT
Montserrat
Malta
TG
Territories
Togo
BJ
Benin
GS
S. Georgia & S. Sandwich
MU
Mauritius
TH
Thailand
BM
BN
Bermuda
Brunei Darussalam
GT
Isls.
Guatemala
MV
MW
Maldives
Malawi
TJ
TK
Tadjikistan
Tokelau
BO
Bolivia
GU
Guam (USA)
MX
Mexico
TM
Turkmenistan
BR
Brazil
GW
Guinea Bissau
MY
Malaysia
TN
Tunisia
BS
BT
Bahamas
Bhutan
GY
HK
Guyana
Hong Kong
MZ
NA
Mozambique
Namibia
TO
TP
Tonga
East Tirnor
BV
Bouvet Island
HM
Heard and McDonald
NC
New Caledonia
TR
Turkey
BW
BY
Botswana
Belarus
HN
Islands
Honduras
NE
NF
Niger
Norfolk Island
TT
TV
Trinidad and Tobago
Tuvalu
BZ
Belize
HR
Croatia
NG
Nigeria
TW
Taiwan
CA
Canada
HT
Haiti
NI
Nicaragua
TZ
Tanzania
CC
CF
Cocos (Keeling) Islands
Central African Republic
HU
ID
Hungary
Indonesia
NL
NO
Netherlands
Norway
UA
UG
Ukraine
Uganda
CG
Congo
IE
Ireland
NP
Nepal
UK
United Kingdom
CH
Switzerland
IL
Israel
NR
Nauru
UM
USA Minor Outlying
CI
CK
Ivory Coast
Cook Islands
IN
IO
India
British Indian Ocean
NU
NZ
Niue
New Zealand
US
Islands
United States
CL
Chile
Territory
OM
Ornan
UY
Uruguay
CM
CN
Cameroon
China
IQ
IR
Iraq
Iran
PA
PE
Panama
Peru
UZ
VA
Uzbekistan
Vatican City State
CO
Colombia
IS
Iceland
PF
Polynesia
(French)
VC
Saint Vincent &
CR
CS
Costa Rica
Former Czechoslovakia
IT
JM
Italy
Jamaica
PG
PH
Papua New Guinea
Philippines
VE
Grenadines
Venezuela
CU
Cuba
JO
Jordan
PK
Pakistan
VG
Virgin Islands (British)
CV
CX
Cape Verde
Christmas Island
JP
KE
Japan
Kenya
PL
PM
Poland
Saint Pierre and Miquelon
Vl
VN
Virgin Islands (USA)
Vietnam
CY
Cyprus
KG
Kyrgyzstan
PN
Pitcairn Island
VU
Vanuatu
CZ
Czech Republic
KH
Cambodia6
PR
Puerto Rico
WF
Wallis and Futuna
DE
DJ
Germany
Djibouti
KI
KM
Kiribati
Comoros
PT
PW
Portugal
Palau
WS
YE
Samoa
Yemen
DK
Denmark
KN
Saint Kitts & Nevis Anguilla
PY
Paraguay
YT
Mayotte
DM
DO
Dominica
Dominican
KP
KR
North Korea
South Korea
QA
RE
Qatar
Reunion (French)
YU
ZA
Yugoslavia
South Africa
DZ
Algeria
KW
Kuwait
RO
Romania
ZM
Zambia
EC
EE
Ecuador
Estonia
KY
KZ
Cayman Islands
Kazakhstan
RU
RW
Russian Federation
Rwanda
ZR
ZW
Zaire
Zimbabwe
EG
EH
Egypt
Western Sahara
LA
LB
Laos
Lebanon
SA
SB
Saudi Arabia
Solomon Islands
Antilles
Samoa
Republic
Islands
(French)
Guinea
(French)
and Jan Mayen
Islands
General
Power requirements
Power consumption
Dimensions (approx.)
Mass (approx.)
Operating temperature
Operating humidity
Signal system
AC 120V, 60 Hz
110W
430 X 81 X 360 mm (17 x 3.2 x 14.2 inches) (w x h x d)
7.2 kg (15.8 Ibs)
5°C to 35°C (41°F to 95°F)
5 % to 90 %
NTSC
Inputs
ANTENNA
VCR VIDEO
VCR AUDIO
FM ANTENNA
AM ANTENNA
DIGITAL AUDIO
IN
IN
IN
IN
IN
IN
Antenna or CATV input, 75 ohms
1 V (p-p) 75 ohms, sync negative, RCA jack x 2
-6.0 dBm more than 47 kohms, RCA jack (L, R) x 2
FM antenna input, 75 ohms
AM antenna input, 300 ohms
Optical connector x 1
Outputs
VIDEO OUT
S-VIDEO OUT
COMPONENT VIDEO OUT
(PROGRESSIVE SCAN)
Audio output (analog audio)
RF OUT
1 V (p-p) 75 ohms, sync negative
(Y) 1.0 V (p-p), 75 ohms, sync negative,
(C) 0.286 V (p-p) 75 ohms
(Y) 1.0 V (p-p), 75 ohms, sync negative,
(Pb)/(Pr) 0.7 V (p-p), 75 ohms, RCA jack
2.0 Vrms (1 KHz, 0 dB), 330 ohms, RCA
Channel 3 or 4 (Adjustable)
Mini DIN 4-pin x 1
RCA jack x 1
x2
jack (L, R) x 1
VCR Specifications
Head system
Timer
Tape speed
Tape width
Maximum recording time
Rewind time
Antenna
Channel coverage
Frequency range
Signal-to-noise ratio
Dynamic range
Channel separation
4 head helical scan azimuth system
12-hour display type with AM, PM
SP: 33.35 mm/sec, LP: 16.67 mm/sec, SLP: 11.12 mm/sec
12.7 mm
SP: 2 HOURS (T-120), SLP: 6 HOURS (T-120)/8 HOURS (T-160)
About 180 seconds (T-120)
75 ohms (VHF/UHF)
VHF: 2-13, UHF: 14-69, CATV: 1-125 (4A, A-W, W+I - W+84, A-5 -A-l)
20Hz to 20kHz
More than 43dB
More than 85 dB (AUDIO OUT jacks)
More than 55 dB (AUDIO OUT jacks)
DVD Specifications
Laser system
Frequency response
Signal-to-noise ratio
Harmonic distortion
Dynamic range
Semiconductor laser, wavelength 650 nm
DVD (PCM 48 kHz): 20 Hz to 20 kHz, CD: 20 Hz to 20 kHz
More than 80 dB (AUDIO OUT jacks)
Less than 0.4%
More than 80 dB (AUDIO OUT jacks)
FM Tuner
Tuning Range
Intermediate Frequency
87.5 - 108.0 MHz
10.7 MHz
AM Tuner
Tuning Range
Intermediate Frequency
530 - 1,720 kHz
450 kHz
Amplifier
Stereo mode
Surround mode
Inputs
70W + 70W (60. at 1 kHz, THD 10 %)
Front: 70W + 70W (60. at 1 kHz, THD 10 %)
Center*: 70W (60` at 1 kHz, THD 10 %)
Surround*: 70W + 70W (60. at 1 kHz, THD 10 %)
Subwoofer*: 150W (40` at 30 Hz, THD 10 %)
*Dependingonthe soundmodesettingsandthe source,theremay be no soundoutput.
LINE 1, LINE 2, OPTICAL IN
Speakers
Type
Impedance
Frequency Response
Sound Pressure Level
Rated Input Power
Max. Input Power
Net Dimensions (W x H x D)
Net Weight
Satellite Speaker
2 Way 2 Speaker
6 0`
110 - 40,000 Hz
83 dB/W (lm)
90 W
180 W
120 x 170 x 107 mm
0.94 kg
Center Speaker
2 Way 2 Speaker
6 0`
110 - 40,000 Hz
83 dB/W (lm)
90 W
180 W
120 x 252 x 107 mm
1.07 kg
Passive Subwoofer
1 Way 1 Speaker
4 0`
40 - 1,500 Hz
82 dB/W (lm)
150 W
300 W
200 x 400 x 381 mm
7.0 kg
Accessories:
Video cable ..................................
Audio cable ..................................
Ferrite core ...................................
RF 75-ohm Coaxial Cable ........................
Speakers ....................................
Speaker cables ................................
AM loop antenna ..............................
FM antenna ..................................
Remote control ................................
Batteries .....................................
1
1
1
1
6
6
1
1
1
2
• This model complies with the above specifications.
• Designs and specifications are subject to change without notice.
• This model may not be compatible with features and/or specifications
Manufactured
Laboratories.
under license from Dolby Laboratories.
that may be added in the future.
"Dolby", "Pro Logic", and the double-D symbol are trademarks of Dolby
J "DTS" and "DTS Digital Surround" are registered trademarks
of Digital Theater Systems, Inc.
I
I
Limited United States Warranty
for DVDiVCF Home Theater System
Toshiba America Consumer Products, EL.C. ("TACP") makes the foilowing limited warranties to original consumers
in the United States. THESE LIMITED WARRANTIES EXTEND TO THE ORIGINAL CONSUMER PURCHASER
OR ANY PERSON RECEIVING THIS DVD/VCR HOME THEATER SYSTEM AS A GIFT FROM THE ORIGINAL
CONSUMER PURCHASER AND TO NO OTHER PURCHASER OR TRANSFEREE.
DVDNCR HOME THEATER SYSTEMS PURCHASED IN THE U.S.A. AND USED ANYWHERE OUTSIDE OF THE
U.S.A, iNCLUDiNG, WITHOUT LiMiTATiON, CANADA AND MEXICO, ARE NOT COVERED BY THESE WARRANTIES.
DVD/VCR HOME THEATER SYSTEMS PURCHASED ANYWHERE OUTSIDE OF THE U.S.A, iNCLUDiNG,
WITHOUT LiMITATiON, CANADAAND MEXICO, AND USED iN THE U.S.A, ARE NOT COVERED BY THESE
WARRANTIES.
Limited Ninety (90) Day Warranty on Labor
TACP warrants this DVD/VCR Home Theater System
and its parts against defects in materials or workmanship for a period of ninety (90) days after the date of
original retail purchase. DURING THiS PERIOD, TACP
WILL, AT TACP'S OPTION, REPAIR OR REPLACE A
DEFECTIVE PART WiTH A NEW OR REFURBISHED
PART WITHOUT CHARGE TO YOU FOR PARTS OR
LABOR.
Limited One (1) Year Warranty on Parts
TACP further warrants the parts in this DVD/VCR Home
Theater System against defects in materials or workmanship for a period of one (1) year after the date of
original retail purchase. DURING THiS PERIOD, TACP
WILL, AT TACP'S OPTION, REPAIR OR REPLACE A
DEFECTIVE PART WiTH A NEW OR REFURBISHED
PART WITHOUT CHARGE TO YOU FOR THE PART,
PROVIDED THAT iF A DEFECTIVE PART iS
REPAIRED OR REPLACED AFTER NINETY (90) DAYS
AFTER THE DATE OF ORiGiNAL RETAIL PURCHASE,
YOU MUST PAY ALL LABOR CHARGES iN CONNECTiON WiTH THE REPAIR OR REPLACEMENT
THEREOR
*Renta_ Units
The warranty' for DVD/VCR Home Theater System
rental units begins on the date of the first rental or thirty
(30) days after the date of shipment to the rental firm,
whichever comes first.
*Limited Warranty for Commercia_ Units
TACP warrants DVD/VCR Home Theater Systems that
are sotd and used for commercial purposes as fol!ows:
all parts are warranted against defects in materials or
workmanship for a period of ninety (90) days after the
date of originat retaiI purchase. DURING THiS PERIOD,
TACP WILL, AT TACP'S OPTION, REPAIR OR
REPLACE A DEFECTIVE PART WiTH A NEW OR
REFURBISHED PART WITHOUT CHARGE TO YOU.
Owner's Manua_ and Product Registration
Card
Read this owner's manuaI thoroughly before operating
this DVD/VCR Home Theater System.
Complete and mail the enclosed product registration
card or register your DVDNCR Home Theater System
online at www.tacp.toshiba.com/service
as soon as possible. By registering your DVD/VCR Home Theater
System you will enable TACP to bring you new products
specifically designed to meet your needs and help us to
contact you in the unlikely event a safety notification is
required under the U.S. Consumer Product Safety Act.
Failure to complete and return the product registration
card does not diminish your warranty rights.
Your Responsibility
THE ABOVE WARRANTIES ARE SUBJECT TO THE
FOLLOWING CONDiTiONS:
(1) You must retain your originaI bill of sale or provide
other proof of purchase.
(2) All warranty servicing of this DVD/VCR Home
Theater System must be performed by an
Authorized TACP Service Station.
(3) The warranties from TACP are effective only if this
DVD/VCR Home Theater System is purchased and
operated in the ContinentaI U.S.A. or Puerto Rico.
(4) Labor service charges for set installation, setup,
adjustment of customer controls and installation or
repair of antenna systems are not covered by this
warranty. Reception problems caused by inadequate
antenna systems are your responsibility.
(5) Warranties extend only to defects in materials or
workmanship as limited above, and do not extend to
any DVD/VCR Home Theater System or parts that
have been Iost or discarded by you or to damage to
the DVD/VCR Home Theater System or parts
caused by fires, misuse, accident, Acts of God (such
as Iightning or fluctuations in eIectric power),
improper installation, improper maintenance, or use
in violation of instructions furnished by TACP; use or
malfunction through simultaneous use of this
DVD/VCR Home Theater System and connected
equipment; or to units that have been modified or
had the seriaI number removed, altered, defaced, or
rendered illegible.
How to Obtain Warranty Service
If, after following all of the operating instructions in this
manual and reviewing the section entitled
"Troubleshooting," you find that service is needed:
(1) To find the nearest TACP Authorized Service
Station, visit TACP's website at
www.tacp.toshiba.com/service
or contact TACP's
Consumer Solution Center toll free at 1-800-6313811.
(2) You must present your original biil of sale or other
proof of purchase to the TACP Authorized Service
Station. You must deliver the entire DVD/VCR
Home Theater System to a TACP Authorized
Service Station. You must pay for all transportation
and insurance charges for the DVDNCR Home
Theater System to and from the TACP Authorized
Service Station.
For additional information, visit TACP's website:
www.tacp.toshiba.com
ALL WARRANTIES IMPLIED BY THE LAW OF ANY
STATE OF THE U.S.A., INCLUDING THE IMPLIED
WARRANTIES OF MERCHANTABILITY AND FITNESS
FOR A PARTICULAR PURPOSE, ARE EXPRESSLY
LIMITED TO THE DURATION OF THE LIMITED WARRANTIES SET FORTH ABOVE. WITH THE EXCEPTION OF ANY WARRANTIES IMPLIED BY THE LAW
OF ANY STATE OF THE U.S.A. AS HEREBY LIMITED,
THE FOREGOING WARRANTY IS EXCLUSIVE AND
IN LIEU OF ALL OTHER WARRANTIES, GUARANTEES, AGREEMENTS, AND SIMILAR OBLIGATIONS
OF TACP WITH RESPECT TO THE REPAIR OR
REPLACEMENT OF ANY PARTS.
IN NO EVENT SHALL TACP BE LIABLE FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES (INCLUDING,
BUT NOT LIMITED TO, LOST PROFITS, BUSINESS
INTERRUPTION, OR MODIFICATION OR ERASURE
OF RECORDED DATA CAUSED BY USE, MISUSE OR
INABILITY TO USE THIS DVDNCR HOME THEATER
SYSTEM).
No person, agent, distributor, dealer or company is
authorized to change, modify or extend the terms of
these warranties in any manner whatsoever. The time
within which an action must be commenced to enforce
any obligation of TACP arising under the warranty or
under any statute, or law of the United States or any
state thereof, is hereby limited to ninety (90) days from
the date you discover or should have discovered, the
defect. This limitation does not apply to implied warranties arising under the law of any state of the U.S.A.
THIS WARRANTY GIVES YOU SPECIFIC LEGAL
RIGHTS AND YOU MAY ALSO HAVE OTHER RIGHTS
WHICH MAY VARY FROM STATE TO STATE IN THE
U.S.A. SOME STATES OF THE U.S.A. DO NOT
ALLOW LIMITATIONS ON THE DURATION OF AN
IMPLIED WARRANTY, WHEN AN ACTION MAY BE
BROUGHT, OR THE EXCLUSION OR LIMITATION OF
INCIDENTAL OR CONSEQUENTIAL DAMAGES.
THEREFORE, THE ABOVE PROVISIONS MAY NOT
APPLY TO YOU UNDER SUCH CIRCUMSTANCES.
ColorStream
and ColorStream
Pro
are registered trademarks of Toshiba
America Consumer Products, L.L.C.
P/NO : 3834RH0074C
Printed in Indonesia.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement