Seagate RN10400-100EUS User manual

ReadyNAS OS 6 Desktop Storage

Systems

Hardware Manual

Models:

Re a d y N A S 1 0 2

Re a d y N A S 1 0 4

Re a d y N A S 2 0 2

Re a d y N A S 2 0 4

Re a d y N A S 3 1 2

Re a d y N A S 3 1 4

Re a d y N A S 3 1 6

Re a d y N A S 5 1 6

Re a d y N A S 7 1 6 X

E DA 5 0 0

March 2015

202-11206-05

350 East Plumeria Drive

San Jose, CA 95134

USA

ReadyNAS OS 6 Desktop Storage Systems

Support

Thank you for selecting NETGEAR products.

After installing your device, locate the serial number on the label of your product and use it to register your product at https://my.netgear.com

. You must register your product before you can use NETGEAR telephone support. NETGEAR recommends registering your product through the NETGEAR website. For product updates and web support, visit http://support.netgear.com

.

Phone (US & Canada only): 1-888-NETGEAR.

Phone (Other Countries): Check the list of phone numbers at http://support.netgear.com/general/contact/default.aspx.

Trademarks

© NETGEAR, Inc. NETGEAR and the NETGEAR Logo are trademarks of NETGEAR, Inc. Any non NETGEAR trademarks are used for reference purposes only.

Compliance

For regulatory compliance information, visit http://www.netgear.com/about/regulatory/ .

2

Contents

Chapter 1 Getting Started

Additional Documentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Setup Location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Supported Operating Systems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Supported Browsers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Diskless Storage Systems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Chapter 2 NETGEAR ReadyNAS 102

Front and Side Panels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Drive Bays . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Rear Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Status Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Power On and Shut Down . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Power On . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Preferred Shutdown . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Forced Shutdown . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Power State . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Boot Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16



Drive Bays . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Rear Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21



Power On . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23


Forced Shutdown . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Power State . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Boot Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24



Drive Bays . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Rear Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30



Power On . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

3



Forced Shutdown . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

Power State . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

Boot Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33



Drive Bays . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

Rear Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40



Power On . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42


Forced Shutdown . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43

Power State . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43

Boot Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43



Drive Bays . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

Rear Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48



Power On . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50


Forced Shutdown . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50

Boot Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51



Drive Bays . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55

Rear Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56



Power On . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58


Forced Shutdown . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58

Boot Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59



Drive Bays . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63

Rear Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64



4


Power On . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65


Forced Shutdown . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66

Boot Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67



Drive Bays. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71

Rear Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72



Power On . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73


Forced Shutdown . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74

Boot Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75

Chapter 10 NETGEAR ReadyNAS 716X


Drive Bays. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79

Rear Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80



Power On . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82


Forced Shutdown . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82

Boot Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83

Chapter 11 NETGEAR EDA 500


Drive Bays. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87

Rear Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88



Power On . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90


Forced Shutdown . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90

Chapter 12 Disks

Disk Trays . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92

Standard Disk Tray . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92

EDA 500 Disk Tray . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93

Supported Disks. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94

Previously Formatted Disks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94

Reformat Previously Formatted Disks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94

Migrate a Volume . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95

5


Add a Disk. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96

Replace a Disk . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103

Appendix A Defaults and Technical Specifications

Factory Default Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111

ReadyNAS 102 Technical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 112








ReadyNAS 716X Technical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120

EDA 500 Technical Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 122

Safety Warnings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 123

Electrical Safety Precautions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 123

General Safety Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 124

Electrostatic Discharge Precautions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 124

6

1.

Getting Started

1

Congratulations on your purchase of a NETGEAR ReadyNAS ® storage system. This manual describes the physical features of the ReadyNAS OS 6 desktop storage systems.

This chapter contains the following sections:

•

Additional Documentation

•

Setup Location

•

Supported Operating Systems

•

Supported Browsers

•

Diskless Storage Systems

7


Additional Documentation

For detailed information about configuring, managing, and using your ReadyNAS storage system, see the ReadyNAS OS 6.2 Software Manual, which is available at http://support.netgear.com/product/ReadyNAS-OS6.

NETGEAR maintains a community website that supports ReadyNAS products. Visit http://www.netgear.com/readynas for reviews, tutorials, a comparison chart, software updates, documentation, an active user forum, and much more.

Setup Location

Your ReadyNAS storage system is suitable for use in a home or small office environment where it can be freestanding. The small, compact size makes it suitable for sitting on a desk or on a closet shelf.

Choose a location for your storage system that meets these criteria:

• Cables can be connected easily.

• Water or moisture cannot enter the case.

• Airflow around the storage system and through the vents in the side of the case is not restricted.

• The air is as free of dust as possible.

• Temperature operating limits are not likely to be exceeded.

• If you are using an uninterruptable power supply (UPS) for protection, the power cable can be securely and safely connected to the UPS.

Supported Operating Systems

The ReadyNAS storage system is supported on the following systems:

• Microsoft Windows 8

• Microsoft Windows 7

• Microsoft Windows Vista

• Apple Mac OS X 10.5 Leopard or later

• Linux, UNIX, Solaris

• Apple iOS

• Google Android

Getting Started

8


Supported Browsers

The ReadyNAS local admin page supports the following browsers:

• Microsoft Internet Explorer 9.0+

• Apple Safari, 5.0+

• Google Chrome 20+

• Mozilla Firefox 14+

If you have difficulty accessing the local admin page or if you notice unexpected behavior, try using another browser. For more information about the ReadyNAS local admin page, see the

ReadyNAS OS 6.2 Software Manual.

Diskless Storage Systems

If you purchased a ReadyNAS storage system without a preinstalled disk drive or drives, you must add at least one disk your system before you use the system. You can add a 3.5-inch hard disk drive, a 2.5-inch hard disk drive, or a 2.5-inch solid state drive to an empty drive bay. For information about how to install a disk, see

Add a Disk on page 96.

Use only supported SATA hard disk drives (HDD) or solid state drives (SSD) in your

ReadyNAS storage system. If you use disks that are not supported, NETGEAR technical support will not provide assistance. For a list of supported disks, see the NETGEAR

Hardware Compatibility List at http://www.netgear.com/readynas-hcl.

If you are adding a previously formatted disk to your storage system, see the instructions in

Previously Formatted Disks on page 94.

Getting Started

9

2.

NETGEAR ReadyNAS 102

2

This chapter provides an overview of the physical features of the ReadyNAS 102 and includes the following sections:

•

Front and Side Panels

•

Drive Bays

•

Rear Panel

•

Status Information

•

Power On and Shut Down

•

Boot Menu

10


Front and Side Panels

The following figure shows the front and side panels of the ReadyNAS 102.

1

2

3

8

Figure 1. ReadyNAS 102 front and side panels

1. Power button and LED

2. Disk activity LED

3. Exhaust vent

4. USB 2.0 port

5. Backup button

6. USB and Backup status LED

7. Disk 1 and Disk 2 LEDs

8. Drive bay door

4 5 6 7


11


Drive Bays

The following figure shows the drive bays of the ReadyNAS 102.

1

2

3

4

5

Figure 2. ReadyNAS 102 drive bays

1. Drive bay door

2. Disk tray handle

3. Recessed disk tray handle lock

4. Disk tray release latch

5. Drive bays


12


Rear Panel

The following figure shows the rear panel of the ReadyNAS 102.

1

2

3

Figure 3. ReadyNAS 102 rear panel

1. Exhaust fan

2. Kensington lock

3. GbE ports with LED status indicators

4. USB 3.0 ports

5. eSATA port

6. Reset button

7. Power adapter socket

4 5 6 7


13


Status Information

You can obtain information about the status of your storage system by reviewing the indicators listed in the following table.

Table 1. ReadyNAS 102 indicator descriptions

Indicator

Power button and LED

Disk LEDs (1, 2)

Disk activity LED

Rear panel Ethernet port

LEDs

Description

Press this button to turn on the ReadyNAS. The LED has these states:

• On. Powered on.

• Blinking. Booting or shutting down.

• Off. Powered off.

Each drive bay has an LED associated with it on the front panel of the storage system. The disk LEDs have these states:

• On. Power is on and the disk is operating normally.

• Blinking. The disk was removed, failed, or is resynchronizing.

• Off. The drive bay is empty.

The disk activity LED has these states:

• On. At least one disk is present.

• Blinking. A disk is active.

• Off. No disks are present.

Two LED status indicators are built into this port, one green and one amber. They indicate port speed and activity as follows:

• Green on, amber off. 1000 Mbps connection speed, no activity.

• Green blinking, amber off. 1000 Mbps connection speed, activity.

• Green off, amber on. 10 Mbps or 100 Mbps connection speed, no activity.

• Green off, amber blinking. 10 Mbps or 100 Mbps connection speed, activity.

• Green off, amber off. No connection.


14


Power On and Shut Down

This section describes how to power on and shut down your system. If you need to shut down the system, use one of the preferred shutdown methods whenever possible.

Power On

 To power on the system:

1. Connect the system to a power supply.

Note: Depending on the system’s last power state, the system might power on automatically. For more information, see

Power State on page 15.

2. If necessary, press the Power button.

The system powers on.

Preferred Shutdown

You can gracefully shut down your system by using the Power button or the ReadyNAS local admin page.

For information about how to gracefully shut down your system using the ReadyNAS local admin page, see the ReadyNAS OS 6.2 Software Manual, which is available at http://support.netgear.com/product/ReadyNAS-OS6.

 To gracefully shut down your system using the Power button:

1. Press the Power button.

The Power LED blinks, prompting you to confirm the shutdown.

2. Press the Power button again.

The system shuts down gracefully.

Forced Shutdown

Perform a forced shutdown only if the storage system is not responding.

 To perform a forced shutdown:

Unplug the system from the power supply.

Power State

If the power supply is interrupted due to a power failure, the system returns to its last state when the power supply is restored:


15


• If the system was powered on at the time of the power failure, the system powers on when the power supply is restored.

• If the system was powered off at the time of the power failure, the system remains off when the power supply is restored.

Boot Menu

Use the boot menu to restart or troubleshoot your ReadyNAS storage system. Your storage system has the following boot modes:

• Normal. Initiates a normal boot process, just like booting using the Power button.

• Factory default. Initiates a short disk test that takes approximately 5 minutes. After the disk test, a 10-minute time-out period begins.

WARNING:

The factory default reboot process resets the storage system to factory settings, erases all data, resets all defaults, and reformats the disk to X-RAID.

If you want to cancel the factory default process, power off the storage system before the 10-minute time-out ends. The system powers down safely without causing any data loss.

If you want to reset the system to factory default settings, do not power off your system. After the 10-minute time-out period, the factory default process begins.

Tip: To start the factory default process immediately, press the Backup button during the 10-minute time-out period.

• OS reinstall. Reinstalls the firmware from the internal flash to the disks. Use the OS reinstall boot mode when the system crashes and corrupts some configuration files. OS reinstall boot mode also resets some settings on your storage system, such as Internet protocol settings and the administrator password, to defaults.

• Tech support. Boots into a low-level diagnostic mode. Use the tech support boot mode only when a NETGEAR technical support representative instructs you to do so.

• Volume read only. Mounts a volume as read-only. Use this option when you are attempting to rescue data off a disk during a disaster recovery.

• Memory test. Performs a memory test. The pass or fail result is reported using the storage system’s LEDs. Contact a NETGEAR technical support representative to interpret memory test results.

• Test disk. Performs an offline full disk test. This process can take four hours or more, depending on the size of your disks. Any problems are reported in the system logs. For more information about viewing the system logs, see the ReadyNAS OS 6.2 Software

Manual, which is available at http://support.netgear.com/product/ReadyNAS-OS6 .


16


 To access the boot menu:

1. Power off your storage system.

2. Using a straightened paper clip, press and hold the Reset button.



4. Continue to press the Reset button until the Power button LED, USB and backup status

LED, disk 1 LED, and disk 2 LED light.

5. Press the Backup button to scroll through boot mode options.

The storage system shows the boot mode options using the LEDs, as described in the following table:

Boot Mode

Boot menu

Normal

Factory default

OS reinstall

Tech support

Volume read only

Memory test

Test disk

Status Indicator

Description

All four LEDs light.

Power LED lights.

Disk 1 LED lights.

Disk 2 LED lights.

USB and backup status LED lights.

Power LED and disk 1 LED light.


Power LED and USB and backup status

LED light.

Power

LED

Disk 1

LED

















































Disk 2

LED









USB and

Backup

LED









Legend:

• On: 

• Off: 

6. Press and release the Reset button to confirm your boot menu selection.

The system boots in the selected boot mode.


17

3.


3


•


•

Drive Bays

•

Rear Panel

•


•


•

Boot Menu

18




2 3 4 5 6

1


1. Exhaust vents

2. USB 2.0 port

3. Backup button and LED

4. Disk LEDs



7. Drive bay door

8. Status display screen

8


19

7


Drive Bays


2

3

4

5

1


1. Drive bay door

2. Disk tray handle



5. Drive bays


20


Rear Panel


2 3 4

5

1

6

7


1. eSATA port

2. Reset button

3. USB 3.0 ports


Note: The two GbE ports are equivalent. They can be used as two separate

Ethernet connections, or can be configured as a single, bonded port with a 2 Gbps potential speed. For information on how to configure a bonded port, and the network configuration requirements needed to support 2 Gbps, see the ReadyNAS OS 6.2 Software Manual, which is available at http://support.netgear.com/product/ReadyNAS-OS6.

5. Power cable socket

6. Exhaust fan

7. Kensington lock


21





Indicator


Disk LEDs (1, 2, 3, 4)

Disk activity LED


LEDs

Status display screen

Description


• On. Powered on.



Each drive bay has an LED associated with it, in numerical order from left to right, along the top of the front panel of the storage system. The disk LEDs have these states:


• Blinking. The disk was removed, failed, or is resynchronizing. See the display screen for details.












Displays messages about the status of your storage system. Note that the status display screen goes to sleep to prevent burn-in. To wake it, press the Power button once. If the storage system reports an abnormal operation or error, the status display screen stays on.


22




Power On











• If the status display screen is not lit, do the following:


The status display screen wakes.

2. Press the Power button a second time.

Instructions for graceful shutdown display on the status display screen.

3. Press the Power button a third time.


• If the status display screen is lit, do the following:






23


Forced Shutdown




Power State




Boot Menu




WARNING:







24




• Memory test. Performs a memory test. The pass or fail result is reported on the status display screen.








4. Continue to press the Reset button until the status display screen shows a boot menu message.


The status display screen shows the current boot mode option.

6. When the status display screen shows the boot mode that you need, press and release the

Reset button to confirm your boot menu selection.



25



26

4.


4


•


•

Drive Bays

•

Rear Panel

•


•


•

Boot Menu

27




1

2

3

8




3. Exhaust vent

4. USB 3.0 port

5. Backup button

6. USB and backup status LED


8. Drive bay door

4 5 6 7


28


Drive Bays


1

2

3

4

5


1. Drive bay door

2. Disk tray handle



5. Drive bays


29


Rear Panel


1

2

3


1. Exhaust fan

2. Kensington lock

3. USB 3.0 ports

4. eSATA port


4 5 6 7

Note: The two GbE ports are equivalent. They can be used as two separate


6. Reset button



30





Indicator


Disk LEDs (1, 2)

Disk activity LED


LEDs

Description


• On. Powered on.









• Off. Disk is idling.

Two LED status indicators are built into each port, one off or green and one showing three states: off, amber, or green. They indicate port speed and activity as follows:

• Green, green. 1000 Mbps connection speed, no activity.

• Green blinking, green. 1000 Mbps connection speed, activity.

• Green, amber. 100 Mbps connection speed, no activity.

• Green blinking, amber. 100 Mbps connection speed, activity.

• Green on, off. 10 Mbps connection speed, no activity.

• Green blinking, off. 10 Mbps connection speed, activity.

• Off, off. No connection.


31




Power On















Forced Shutdown





32


Power State




Boot Menu




WARNING:









33


• Memory test. Performs a memory test. The memory test runs for 8hrs. The current status and the pass or fail result is reported using the storage system LEDs, as described in the following table:

Memory Test State Power LED Disk 1 LED Disk 2 LED Backup LED

1st hour Off Off Off Blinking

2nd hour

3rd hour

Off

Off

Off

Blinking

Blinking

Off

Off

Off

4th hour

5th hour

6th hour

7th hour

Off

On

On

On

Blinking

Off

Off

Blinking

Blinking

Off

Blinking

Off

Blinking

Blinking

Off

Off

8th hour

Result: fail

Result: pass

On

Blinking

On

Blinking

Blinking

On

Blinking

Blinking

On

Blinking

Blinking

On












34



Boot Mode

Boot menu

Normal

Factory default

OS reinstall

Tech support

Volume read only

Memory test

Test disk


Description


Power LED lights.

Disk 1 LED lights.

Disk 2 LED lights.





LED light.

Power

LED

Disk 1

LED

















































Disk 2

LED









USB and

Backup

LED









Legend:

• On: 

• Off: 




35



36

5.


5


•


•

Drive Bays

•

Rear Panel

•


•


•

Boot Menu

37




2 3 4 5 6

1


1. Exhaust vents

2. USB 2.0 port


4. Disk LEDs



7. Drive bay door


8


38

7


Drive Bays


2

3

4

5

1


1. Drive bay door

2. Disk tray handle



5. Drive bays


39


Rear Panel


2 3 4

5

1

6

7


1. eSATA port

2. Reset button

3. USB 3.0 ports

4. LAN ports with LED status indicators

Note: The two LAN ports are equivalent. They can be used as two separate



6. Exhaust fan

7. Kensington lock


40





Indicator


Disk LEDs (1, 2, 3, 4)

Disk activity LED


LEDs


Description


• On. Powered on.



Each drive bay has an LED associated with it, in numerical order from left to right, along the top of the front panel of the storage system. The disk LEDs have these states:





• Blinking. A disk is being accessed.

• Off. All disks are idle.

Two LED status indicators are built into each port, one off or green and one showing three states: off, amber, or green. They indicate port speed and activity as follows:

• Green, green. 1000 Mbps connection speed, no activity.

• Green blinking, green. 1000 Mbps connection speed, activity.

• Green, amber. 100 Mbps connection speed, no activity.

• Green blinking, amber. 100 Mbps connection speed, activity.

• Green on, off. 10 Mbps connection speed, no activity.

• Green blinking, off. 10 Mbps connection speed, activity.

• Off, off. No connection.



41




Power On
























42


Forced Shutdown




Power State




Boot Menu




WARNING:







43



















44

6.


6


•


•

Drive Bays

•

Rear Panel

•


•


•

Boot Menu

45




1

2

3

9




3. Exhaust vent

4. USB 2.0 port

5. Infrared remote receiver

6. Backup button

7. USB and Backup status LED


9. Drive bay door

4 5 6 7 8


46


Drive Bays


1

2

3

4

5


1. Drive bay door

2. Disk tray handle



5. Drive bays


47


Rear Panel


1

2


3 4 5

1. Exhaust fan

2. Kensington lock

3. USB 3.0 ports

4. eSATA port


6. Reset button

7. HDMI port (not currently supported)


6 7 8


48





Indicator


Disk LEDs (1, 2)

Disk activity LED


LEDs

Description


• On. Powered on.





• Blinking. The disk was removed, failed, or is resynchronizing.













49




Power On

When the system is connected to a power supply, the system automatically powers on.

You can also power on the system by pressing the Power button.









Forced Shutdown



Press and hold the Power button for five seconds.

The LEDs blink quickly and simultaneously to warn that power will be cut off forcibly.

The system shuts down.


50


Boot Menu




WARNING:








• Memory test. Performs a memory test. The pass or fail result is reported using the storage system’s LEDs. Contact a NETGEAR technical support representative to interpret memory test results.




51











Boot Mode

Boot menu

Normal

Factory default

OS reinstall

Tech support

Volume read only

Memory test

Test disk


Description


Power LED lights.

Disk 1 LED lights.

Disk 2 LED lights.





LED light.

Power

LED

Disk 1

LED

















































Disk 2

LED









USB and

Backup

LED









Legend:

• On: 

• Off: 




52

7.


7


•


•

Drive Bays

•

Rear Panel

•


•


•

Boot Menu

53




2 3

4 5 6 7

1

8


1. Exhaust vents

2. Shared USB 2.0 and eSATA port


4. Disk LEDs




8. Drive bay door



54

9


Drive Bays


2

3

4

5

1


1. Drive bay door

2. Disk tray handle



5. Drive bays


55


Rear Panel


1 2 3 4 5

6

7

8


1. Reset button


3. eSATA port

4. USB 3.0 ports



7. Exhaust fan

8. Kensington lock


56





Indicator


Disk LEDs (1, 2, 3, 4)

Disk activity LED


LEDs


Description


• On. Powered on.



Each drive bay has an LED associated with it, in numerical order from left to right along the top of the front panel of the storage system. The disk LEDs have these states:
















57




Power On

When the system is connected to a power supply, the system automatically powers on.

You can also power on the system by pressing the Power button.

















Forced Shutdown



Press and hold the Power button for five seconds.


58




Boot Menu




WARNING:












59






The systems powers on.








60

8.


8


•


•

Drive Bays

•

Rear Panel

•


•


•

Boot Menu

61




1 2


1. Status and Menu display screen


3. Drive bay door

4. Touchpad and backlight

5. OK button

5 4

3


62


Drive Bays


1


1. Drive bay door



4. USB 2.0 port

5. Disk tray handle

6. Power button

7. Disk LED

8. Drive bays


63

2 3 4 5 6 7

8

1

2

3

4


Rear Panel


5

6

7

8

9


1. Exhaust fan


3. Power switch

4. Kensington lock

5. eSATA ports



8. USB 3.0 ports

9. Reset button


64





Indicator

Disk LEDs


LEDs


Description

A disk LED next to each drive bay indicates the status of the disk inside. The disk

LEDs have these states:

• Solid blue. Power is on and the disk is operating normally.

• Blinking blue. The disk is active.

• Solid red. The disk was removed, failed, or is resynchronizing. See the display screen for details.

• Off. No disk is present.







Displays messages about the status of your storage system. Note that the status display screen goes to sleep to prevent burn-in. To wake the status display screen, activate the proximity sensor, press the touchpad, press the OK button, or press the Power button once. If the storage system reports an abnormal operation or error, the status display screen stays on.



Power On

When the system is connected to a power supply and the Power switch is in the On position, the system automatically powers on.

You can also power on the system by pressing the Power button on the front panel of the system.




65





1. Press the Power button on the front panel of the system.











Forced Shutdown



Press and hold the Power button on the front panel of the system for five seconds.




66


Boot Menu




WARNING:




Tip: To start the factory default process immediately, press the OK button during the 10-minute time-out period.








67








5. Use the arrows on the touchpad to scroll through boot mode options.


6. When the status display screen shows the boot mode that you need, press the OK button to confirm your boot menu selection.



68

9.


9


•


•

Drive Bays

•

Rear Panel

•


•


•

Boot Menu

69




1 2

3


1. Status and menu display screen


3. Drive bay door


5. OK button

5 4


70


Drive Bays


1 2 3 4 5 6 7


1. Drive bay door



4. USB 2.0 port

5. Disk tray handle

6. Power button

7. Disk LED

8. Drive bays


71

8


Rear Panel


1

2

3

4

5

6

7

8

9

10


1. Exhaust fan


3. Power switch

4. Kensington lock

5. eSATA ports


7. HDMI port

8. eSATA port

9. USB 3.0 ports

10. Reset button


72





Indicator

Disk LEDs


LEDs


Description
















Power On






73
















Forced Shutdown



Press and hold the Power button on the front panel of the system for five seconds.




74


Boot Menu




WARNING:












75













76

10.

NETGEAR ReadyNAS 716X

10

This chapter provides an overview of the physical features of the ReadyNAS 716X and includes the following sections:

•


•

Drive Bays

•

Rear Panel

•


•


•

Boot Menu

77



The following figure shows the front and side panels of the ReadyNAS 716X.

1 2

3

Figure 25. ReadyNAS 716X front and side panels

1. Status and menu display screen


3. Drive bay door


5. OK button

5 4


78


Drive Bays

The following figure shows the drive bays of ReadyNAS 716X.

1 2 3 4 5 6 7

Figure 26. ReadyNAS 716X drive bays

1. Drive bay door



4. USB 2.0 port

5. Disk tray handle

6. Power button

7. Disk LED

8. Drive bays


79

8


Rear Panel

The following figure shows the rear panel of ReadyNAS 716X.

1

2

3

4

5

6

7

8

9

10

11

Figure 27. ReadyNAS 716X rear panel

1. Exhaust fan


3. Power switch

4. Kensington lock

5. eSATA ports

6. 1Gb LAN ports with LED status indicators

7. HDMI port

8. eSATA port

9. USB 3.0 ports

10. Reset button

11. 10 Gb LAN ports with LED status indicators


80




Table 9. ReadyNAS 716X indicator descriptions

Indicator

Disk LEDs


LEDs (1 Gb)


LEDs (10 Gb)


Description













Two LED status indicators are built into this port. They indicate port speed and activity as follows:

• LED 1

- Off. No link.

- Solid green. Linked.

- Blinking green. Activity

• LED 2

- Solid green. 10 GbE

- Solid yellow. 1 GbE

- Off. 100 Mbps





81


Power On



















Forced Shutdown



Press and hold the Power button on the front panel of the system for 5 seconds.




82


Boot Menu




WARNING:






• Tech support. Boots into a low-level diagnostic mode. Use the tech support boot mode only when instructed to do so by a NETGEAR technical support representative.






83













84

11.

NETGEAR EDA 500

11

This chapter provides an overview of the physical features of the EDA 500 and includes the following sections:

•


•

Drive Bays

•

Rear Panel

•


•


Note: The EDA 500 disk trays are slightly different from the standard trays.

Use only EDA 500 disk trays with the EDA 500. For more information about the EDA 500 disk trays, see

EDA 500 Disk Tray on page 93.

A ReadyNAS cannot boot using the disks in an EDA 500. All disks in a RAID volume must be either in a ReadyNAS or in an EDA 500. A RAID volume cannot combine disks in a

ReadyNAS with disks in an EDA 500.

You can add an EDA 500 to a ReadyNAS while the ReadyNAS is running, but you cannot remove the EDA while the ReadyNAS is running.

You can add and remove disks while an EDA 500 is in operation (hot swap). If an added disk has data on it, the data shows as an inactive volume. You need to destroy inactive volumes, which destroys all data in the volume, and create new volumes, before the space is available for use by the ReadyNAS.

85



The following figure shows the front and side panels of EDA 500.

Figure 28. EDA 500 front and side panels

1. Power LED

2. eSATA LED

3. Volume LED

4. Alert LED

5. Drive bay door

1 2 3 4

5

NETGEAR EDA 500

86


Drive Bays

The following figure shows the drive bays of EDA 500.

1

2 3 4 5

Figure 29. EDA 500 drive bays

1. Drive bay door



4. Disk tray handle

5. Power button

6. Disk LED

7. Disk label

8. Active drive bays

9. Cold spare drive bay

NETGEAR EDA 500

87

7

6

8

9


Rear Panel

The following figure shows the rear panel of EDA 500.

5

1

2 3

Figure 30. EDA 500 rear panel

1. Exhaust fan

2. Kensington lock

3. Power switch


5. eSATA port

4

NETGEAR EDA 500

88




Table 10. EDA 500 indicator descriptions

Indicator

Power LED eSATA LED

Volume LED

Alert LED

Disk LEDs

Description

The Power LED has these states:

• On. Powered on.


The eSATA LED has these states:

• On. The SATA link is established between the EDA 500 and a host.

• Off. The SATA link is not established.

The Volume LED has these states:

• On. The data volume or volumes are mounted by a host.

• Off. The data volume or volumes are not mounted. You can safely disconnect the eSATA cable.

The Alert LED has these states:

• On. The system needs attention. Use the local admin page to determine the problem. For more information, see the ReadyNAS OS 6.2 Software Manual, which is available at http://support.netgear.com/product/ReadyNAS-OS6 .

• Off. The system is healthy.

A disk LED next to each active drive bay indicates the status of the disk inside.

(The cold spare drive bay has no LED.) The disk LEDs have these states:





NETGEAR EDA 500

89



This section describes how to power on and shut down your system. If you need to shut down the system, use the preferred shutdown method whenever possible.

Power On


When connected to a host that is powered on, the EDA 500 automatically powers on. The

EDA 500 detects a powered-on host through the eSATA link.



If possible, always unmount the EDA 500 volumes from the host before shutting down the

EDA 500.

Use the ReadyNAS local admin page to gracefully shut down the EDA 500. For information about how to gracefully shut down the EDA 500 using the ReadyNAS local admin page, see the ReadyNAS OS 6.2 Software Manual, which is available at http://support.netgear.com/product/ReadyNAS-OS6.

Forced Shutdown



Flip the Power switch on the back panel of the system to the Off position.

NETGEAR EDA 500

90

12.

Disks

12

This chapter describes how to reformat, add, and replace disks in your ReadyNAS OS 6 storage system.

For information about configuring disks on your storage system, see the ReadyNAS OS 6.2

Software Manual, which is available at http://support.netgear.com/product/ReadyNAS-OS6 .

This chapter includes the following topics:

•

Disk Trays

•

Supported Disks

•

Previously Formatted Disks

•

Add a Disk

•

Replace a Disk

91


Disk Trays

All systems except the EDA 500 use standard disk trays. The EDA 500 comes with its own special disk trays. This section describes both the standard and EDA 500 disk trays.

Standard Disk Tray

The following figure shows the features of the standard disk tray. This disk tray is used in all systems except the EDA 500. For information about the EDA 500 disk tray, see

EDA 500

Disk Tray on page 93.

1

5

2 6

3

4

7

Figure 31. Standard disk tray

1. Disk tray



4. Disk tray handle

5. Disk screw holes

6. Mounting bracket

7. Bracket lock

IMPORTANT:

To maintain adequate airflow, make sure that all disk trays remain in the drive bays, even if no disk is installed in the tray.

Do not use standard disk trays with the EDA 500. Use only EDA 500 disk trays with the EDA 500.

Disks

92


EDA 500 Disk Tray

The following figure shows the features of the EDA 500 disk tray. The EDA 500 disk tray and the standard disk tray are the same, except for the EMI shielding on the EDA 500 disk tray.

For this reason, use only EDA 500 disk trays with the EDA 500.

1

5

2 6

3

4 7

8

Figure 32. EDA 500 disk tray

1. Disk tray



4. Disk tray handle

5. Disk screw holes

6. Mounting bracket

7. Bracket lock

8. EMI shielding

IMPORTANT:

Use only EDA 500 disk trays with the EDA 500. Do not use standard disk trays with the EDA 500.

To maintain adequate airflow, make sure that all disk trays remain in the drive bays, even if no disk is installed in the tray.

Disks

93


Supported Disks

Use only supported SATA hard disk drives (HDD) or solid state drives (SSD) in your

ReadyNAS storage system. If you use disks that are not supported, NETGEAR technical support will not provide assistance. For a list of supported disks, see the NETGEAR

Hardware Compatibility List at http://www.netgear.com/readynas-hcl.

Previously Formatted Disks

This section describes how to use previously formatted disks with your ReadyNAS OS 6 storage system.

Previously formatted disks must appear on the NETGEAR Hardware Compatibility List, which is available at http://www.netgear.com/readynas-hcl.

Reformat Previously Formatted Disks

If you want to use disks that were previously formatted for an operating system other than

ReadyNAS OS 6 (for example, Windows or RAIDiator), you must reformat the disks.

If you want to use disks from another ReadyNAS OS 6 storage system, see Migrate a

Volume on page 95.

Note: If you try to use previously formatted disks in a system that does not contain any other disks, the system does not boot and ReadyCLOUD does not discover your device. If you use RAIDar to discover your device, RAIDar displays a “Corrupt Root” error message.

If you try to use previously formatted disks in a system that already contains usable disks, the system does not reformat or use the previously formatted disks. Any data on the previously formatted disk remains intact.

The following instructions describe how to reformat previously formatted disks in a

ReadyNAS OS 6 system. This procedure assumes that the system does not contain any other disks.

 To reformat previously formatted disks with a diskless ReadyNAS OS 6 system:

1. Gracefully shut down the storage system.

For information about how to gracefully shut down your system, see the Preferred

Shutdown section of the chapter that describes your system.

2. Install the disks.

Disks

94


For more information, see


3. Reset the system to its factory default settings.

WARNING:

This process erases all data and reformats all disks into a single

X-RAID volume. If you want to preserve the data on the disks, you must back up the data to an external drive before using the disks in your ReadyNAS storage system.

For information about how to reset the system to its factory default settings, see the Boot

Menu section of the chapter that describes your system.

The disk is reformatted and becomes available for use with your ReadyNAS OS 6 storage system.

Migrate a Volume

You can migrate a volume from one ReadyNAS OS 6 storage system to another, as long as you migrate every disk in the volume. For example, if you want to migrate a volume that contains two disks, you must add both disks to the new system. If you add only part of a volume to the new system, the system recognizes the disk as a degraded volume.

If your ReadyNAS storage system is operating with one or more disks, you can add disks while the system is running. The new system recognizes the migrated volume and its data.

For more information about adding a disk while the system is running, see


If your ReadyNAS storage system does not have any disks installed, perform the following procedure.

 To migrate a volume to a diskless ReadyNAS OS 6 system:

1. Gracefully shut down the new (diskless) storage system.



2. Remove each disk in the volume from the old system.

3. Install each disk in the volume into the new storage system.

For more information, see


4. Turn on the new system by pressing the Power button.

The new system recognizes the migrated volume and its data.

Disks

95


Add a Disk

You can add a 3.5-inch hard disk drive, a 2.5-inch hard disk drive, or a 2.5-inch solid state drive to an empty drive bay.

If you want to add a previously formatted disk to your storage system, see the instructions in

Previously Formatted Disks on page 94.

 To add a 3.5-inch hard disk drive (HDD):

1. Determine whether you need to shut down your system:

• If you are adding disks to a diskless system, gracefully shut down the system.



• If your system is operating with one or more disks, you can add disks while the system is running. You do not need to shut down the system.

2. If necessary, slide the recessed handle lock to the unlocked position.

3. Press the disk tray release latch.

The disk tray handle pops out.

4. Pull out the disk tray.

5. Separate the mounting bracket from the disk tray:

a. Press and hold the disk tray release latch.

Disks

96


b. While holding the release latch, use your other hand to pull out one end of the mounting bracket and then the other until the ends extend slightly past the disk tray.

Make sure that the ends of the mounting bracket are even with each other.

c. Slide the bracket down the disk tray, keeping both sides of the bracket even with each other.

Bracket lock

The mounting bracket stops when it hits the bracket lock.

The bracket lock prevents the mounting bracket from sliding all the way off the disk tray.

6. Attach the new HDD to the mounting bracket.

Disks

97


Make sure that the HDD mounting holes are aligned with the bracket’s mounting posts and that the HDD connectors face the interior of the disk tray.

7. Push the mounting bracket and HDD back into the disk tray.

Disks

98


WARNING:

To prevent damage to your system, make sure that the disk tray is correctly oriented before inserting it into the drive bay.

8. Insert the disk tray back into the drive bay of the storage system.

• For 2-bay and 4-bay systems, insert the disk tray so that the disk tray release latch is near the bottom of the system.

• For 6-bay systems, insert the disk tray so that the disk tray release latch is on the left side of the system.

9. Press down on the disk tray handle until it latches closed.

The disk tray is secured in the drive bay.

10. If necessary, turn on your system by pressing the Power button.

If the disk that you added was not previously formatted, the system uses the disk in one of the following ways:

• If you are adding the disk to a system that uses X-RAID, the system automatically determines whether the disk is used for protection or storage. The new disk is incorporated in the background while you continue to use your system.

• If you are adding the disk to a system that uses Flex-RAID, the disk becomes available for use. You use the local admin page to manually configure the new disk.

For more information about X-RAID, Flex-RAID, and using the local admin page, see the

ReadyNAS OS 6.2 Software Manual, which is available at http://support.netgear.com/product/ReadyNAS-OS6.

 To add a 2.5-inch hard disk drive (HDD) or 2.5-inch solid state drive (SSD):

1. Determine whether you need to shut down your system:

• If you are adding disks to a diskless system, gracefully shut down the system.



• If your system is operating with one or more disks, you can add disks while the system is running. You do not need to shut down the system.


Disks

99





5. Remove the mounting bracket from the disk tray:

a. Press and hold the disk tray release latch.

b. While holding the release latch, use your other hand to pull out one end of the mounting bracket and then the other until the ends extend slightly past the disk tray.

Make sure that the ends of the mounting bracket are even with each other.

Disks

100


c. Slide the bracket down the disk tray, keeping both sides of the bracket even with each other.

Bracket lock



d. Push the mounting bracket out of each bracket lock using a pointed object, such as a pen.

The mounting bracket is released from the bracket locks.

e. Slide the mounting bracket out of the disk tray.

The mounting bracket is not used to secure 2.5-inch HDDs or SSDs.

Disks

101


6. Place the new 2.5-inch HDD or SSD in the disk tray.

7. Secure the HDD or SSD to the disk tray using the screws that came with your storage system.

Make sure that the HDD or SSD connectors face the interior of the disk tray.

Make sure that the HDD or SSD is installed on the correct side of the disk tray.

WARNING:




Disks

102





10. If necessary, turn on your system by pressing the Power button.

If the disk that you added was not previously formatted, the system uses the disk in one of the following ways:

• If you are adding the disk to a system that uses X-RAID, the system automatically determines whether the disk is used for protection or storage. The new disk is incorporated in the background while you continue to use your system.

• If you are adding the disk to a system that uses Flex-RAID, the disk becomes available for use. You use the local admin page to manually configure the new disk.

For more information about X-RAID, Flex-RAID, and using the local admin page, see the

ReadyNAS OS 6.2 Software Manual, which is available at http://support.netgear.com/product/ReadyNAS-OS6.

Replace a Disk

If your volumes use a protected RAID configuration, your system can recover from the failure of a disk. When you replace the failed disk, the system rebuilds the volume using the new disk and no data from the volume is lost.

The Disk LEDs can help you identify a failed disk. For more information, see the Status

Information section of the chapter that describes your system. You can also use the local admin page to set up email alerts that notify you when a disk fails. In addition, the local admin page provides information about the failed disk.

For information about RAID configurations, setting up email alerts, and using the local admin page, see the ReadyNAS OS 6.2 Software Manual, which is available at http://support.netgear.com/product/ReadyNAS-OS6 .

ReadyNAS supports hot-swap drive bays, so you do not need to power down your storage system when replacing a disk.

If you are replacing a disk with a previously formatted disk, see the instructions in

Previously

Formatted Disks on page 94.

WARNING:

Replace one disk at a time. Wait for the volume to resynchronize your data before replacing another disk. If you attempt to replace more than one disk at a time, the system will crash.

Disks

103


 To replace a 3.5-inch hard disk drive (HDD):





4. Press and hold the disk tray release latch.

Disks

104


5. While holding the disk tray release latch, pull out the mounting bracket and slide the bracket down the tray.

Mounting bracket



6. Remove the old HDD from the mounting bracket.

7. Attach the new HDD to the mounting bracket.

Disks

105


Make sure that the HDD mounting holes are aligned with the bracket’s mounting posts and that the HDD connectors face the interior of the disk tray.

8. Push the mounting bracket and HDD back into the disk tray.

Disks

106


WARNING:







If the volume that contained the failed disk uses a protected RAID configuration, the system automatically resynchronizes the volume using the new disk. Resynchronization might take several hours, depending on the disk size. You can continue to use your storage system, although access is slower until the volume resynchronization finishes.

For more information about RAID configurations, see the ReadyNAS OS 6.2 Software

Manual, which is available at http://support.netgear.com/product/ReadyNAS-OS6.

 To replace a 2.5-inch hard disk drive (HDD) or 2.5-inch solid state drive (SSD):



The tray handle pops out.


Disks

107


4. Replace the 2.5-inch HDD or SSD:

a. Remove the screws and the old 2.5-inch HDD or SSD.

b. Place the new 2.5-inch HDD or SSD in the disk tray.

c. Secure the HDD or SSD to the disk tray using the screws.

Make sure that the disk connectors face the interior of the disk tray.

Disks

108


Make sure that the HDD or SSD is installed on the correct side of the disk tray.

WARNING:







If the volume that contained the failed disk uses a protected RAID configuration, the system automatically resynchronizes the volume using the new disk. Resynchronization might take several hours, depending on the disk size. You can continue to use your storage system, although access is slower until the volume resynchronization finishes.

For more information about RAID configurations, see the ReadyNAS OS 6.2 Software

Manual, which is available at http://support.netgear.com/product/ReadyNAS-OS6.

Disks

109

A.

Defaults and Technical

Specifications

This appendix includes the following sections:

•

Factory Default Settings

•

ReadyNAS 102 Technical Specifications

•


•


•


•


•


•


•


•

ReadyNAS 716X Technical Specifications

•

EDA 500 Technical Specifications

•

Safety Warnings

A

110


Factory Default Settings

The following table lists factory default settings for ReadyNAS OS 6 desktop storage systems.

Table 11. ReadyNAS OS 6 factory default settings

Feature

Login

Default IP address

Default

The default IP address for the ReadyNAS is assigned by the local router (DHCP server).

Admin user name (case-sensitive)

Admin login password (case-sensitive)

Management

System configuration

If a router does not assign an IP address, the ReadyNAS defaults to the IP address https://169.254.x.x, where the last two octets are randomly generated based on the system’s MAC address.

admin password

ReadyNAS local admin page web-based configuration and status monitoring

ReadyCloud for Windows, Mac, and Linux Discovery, setup, and multi-storage system status monitoring web

LAN Connections

MAC address

MTU size

Ethernet port

LAN IP address

See product label

1500

Auto Sense 10/100/1000BASE-T, RJ-45

DHCP acquired

Defaults and Technical Specifications

111


ReadyNAS 102 Technical Specifications

The ReadyNAS 102 storage system meets the following technical specifications:

General:

• Marvell Armada 370 1.2 GHz CPU

• 512 MB memory

• Two-bay storage

• One eSATA port

• One USB 2.0 port (front)

• Two USB 3.0 ports (back)

• One GbE port

Physical dimensions (h x w x d):

• 142 x 101 x 220 mm (5.60 x 3.98 x 8.70 in.)

Physical weight:

• 2.12 kg (4.67 lb) without disks

Power consumption:

• BTU at full power supply utilization: 31.7W

• In operation: 31W

• Power off (Wake On LAN): 1.0 W

• Power off: 210 mW

Electrical:

• External 60 W (12V, 5A) AC power supply

• Input: 100–240V AC, 50/60 Hz

Environmental requirements:

• Operating temperature: 0 to 40°C (32° to 104°F)

• Operating humidity: 20 to 80% relative humidity (non-condensing)

• Storage temperature: –20 to 70°C (–4 to 158°F)

• Storage humidity: 5 to 95% relative humidity (non-condensing)

• Software-controlled 92 mm chassis cooling fan


112


Certifications:

FCC Class B, CE Class B, RoHS, VCCI Class B



General:

• Marvell Armada 370 1.2 GHz CPU

• 512 MB memory

• Four-bay storage

• One eSATA port



• Two GbE ports

• LCD display


• 205 x 134 x 223 mm (8.97 x 5.28 x 8.78 in.)




• BTU at full power supply utilization: 47 W

• In operation: 45.6 W


• Power off: 0.44 W

Electrical:


• Input: 100–240VAC, 50/60 Hz






113




Certifications:

• FCC Class B, CE Class B, RoHS, VCCI Class B



General:

• Annapurna Labs AL212 1.4GHz processor

• 2 GB memory

• Two-bay storage

• One eSATA port



• Two GbE ports


• 142 x 101 x 220 mm (5.60 x 3.98 x 8.70 in.)




• BTU at full power supply utilization: 39.5 W

• In operation: 38 W


Electrical:


• Input: 100–240V AC, 50/60 Hz






114




Certifications:

FCC Class B, CE Class B, RoHS, VCCI Class B, CCC



General:

• Annapurna Labs AL212 1.4GHz processor

• 2 GB memory


• One eSATA port



• Two GbE ports

• LCD display


• 205 x 134 x 223 mm (8.97 x 5.28 x 8.78 in.)







Electrical:


• Input: 100–240VAC, 50/60 Hz





115





Certifications:

• FCC Class B, CE Class B, RoHS, VCCI Class B, CCC



General:

• Intel Atom 2.1 GHz Dual Core CPU

• 2 GB memory

• Two-bay storage

• One eSATA port

• One HDMI port (not currently supported)



• Two LAN ports

• Infrared remote receiver


• 142 x 101 x 220 mm (5.60 x 3.98 x 8.70 in.)






• Power off (Wake On LAN): 627.07 mW

• Power off: 266.61 mW

Electrical:


• Input: 100–240VAC, 50/60 Hz


116








Certifications:




General:


• 2 GB memory


• Two eSATA ports (one shared USB 2.0 and eSATA port)




• Two LAN ports

• LCD display



• 205 x 134 x 223 mm (8.97 x 5.28 x 8.78 in.)









117


Electrical:


• Input: 100–240VAC, 50/60 Hz







Certifications:




General:


• 2 GB memory

• Six-bay storage

• Two eSATA ports




• Two LAN ports

• LCD display


• Proximity sensor


• 259 x 192 x 287.5 mm (10.20 x 7.56 x 11.32 in.)




118







Electrical:

• Internal 200 W server-rated AC power supply

• Input: 100–240VAC, 50/60 Hz







Certifications:




General:

• Intel Core i3 3.3 GHz Dual Core CPU

• 4 GB ECC memory

• Six-bay storage

• Three eSATA ports

• One HDMI port



• Two LAN ports

• LCD display




119



• 259 x 192 x 287.5 mm (10.20 x 7.56 x 11.32 in.)








Electrical:


• Input: 100–240VAC, 50/60 Hz







Certifications:


ReadyNAS 716X Technical Specifications

The ReadyNAS 716X storage system meets the following technical specifications:

General:

• Intel Xeon processor E3-1265L v2 CPU

• 16 GB ECC memory

• Six-bay storage

• Three eSATA ports

• One HDMI port



120



• Two 1GbE LAN ports

• Two 10GbE LAN ports

• LCD display




• 259 x 192 x 287.5 mm (10.20 x 7.56 x 11.32 in.)








Electrical:

• Internal 200W server-rated AC power supply

• Input: 100–240VAC, 50/60 Hz







Certifications:



121


EDA 500 Technical Specifications

The EDA 500 storage system meets the following technical specifications:

General:

• Five-bay storage

• One eSATA port



• 259 x 192 x 287.5 mm (10.20 x 7.56 x 11.32 in.)







Electrical:


• Input: 100–240V AC, 50/60 Hz






• Software controlled 120 mm chassis cooling fan

Certifications:



122


Safety Warnings

• The equipment contains no operator access areas and is certified for installation only by trained personnel, according to the installation instructions provided with each storage system.

• Install the socket-outlet near the equipment in an easily accessible location.

• Observe the on-board battery precautions.

DANGER:

Risk of explosion if battery is replaced by an incorrect type. Dispose of used batteries according to their instructions.

• Connect the storage systems and their associated LAN connections only to equipment within the same building.

Electrical Safety Precautions

Follow basic electrical safety precautions to protect yourself from harm and the ReadyNAS from damage:

• Be aware of the locations of the power on/off switch on the chassis as well as the room’s emergency power-off switch, disconnection switch, or electrical outlet. If an electrical accident occurs, you can then quickly remove power from the system.

• Do not work alone when working with high-voltage components.

• Always disconnect power from the system when removing or installing main system components, such as the main board or memory modules. When disconnecting power, first power down the system with the operating system and then unplug the power cords of all the power supply storage systems in the system.

• When working around exposed electrical circuits, ensure that another person who is familiar with the power-off controls is nearby to switch off the power if necessary.

• Use only one hand when working with powered-on electrical equipment. This is to avoid making a complete circuit, which will cause electrical shock. Use extreme caution when using metal tools, which can easily damage any electrical components or circuit boards they come into contact with.

• Do not use mats designed to decrease static electrical discharge as protection from electrical shock. Instead, use rubber mats that have been specifically designed as electrical insulators.

• Use only power supply cords that include a grounding plug and plug them into grounded electrical outlets.


123


General Safety Precautions

Follow these rules to ensure general safety:

• Keep the area around the ReadyNAS clean and free of clutter.

• See the technical specifications in this manual for details about your specific ReadyNAS storage systems.

• Replace the on-board battery only with the same battery or an equivalent type of battery recommended by the manufacturer. Dispose of used batteries according to the manufacturer’s instructions.

DANGER:

Installing the battery upside down reverses its polarities and creates a danger of explosion.

• Only trained service technicians can replace the soldered-in self-resetting PTC (positive temperature coefficient) fuses on the main board, using only new fuses that are the same as or equivalent to the ones being replaced. Contact technical support for details and support.

Electrostatic Discharge Precautions

Electrostatic discharge (ESD) is generated by two objects with different electrical charges coming into contact with each other. An electrical discharge is created to neutralize this difference, which can damage electronic components and printed circuit boards. The following measures are generally sufficient to neutralize this difference before contact is made to protect your equipment from ESD:

• Use a grounded wrist strap designed to prevent static discharge.

• Keep all components and printed circuit boards (PCBs) in their antistatic bags until ready for use.

• Touch a grounded metal object before removing the board from the antistatic bag.

• Do not let components or PCBs come into contact with your clothing, which might retain a charge even if you are wearing a wrist strap.

• Handle a board by its edges only; do not touch its components, peripheral chips, memory modules, or contacts.

• When handling chips or modules, avoid touching their pins.

• Put the main board and peripherals back into their antistatic bags when not in use.

• For grounding purposes, make sure your computer chassis provides excellent conductivity between the power supply, the case, the mounting fasteners, and the main board.


124

Seagate RN10400-100EUS User manual

ReadyNAS OS 6 Desktop Storage

Systems

Hardware Manual

Contents

Getting Started

NETGEAR ReadyNAS 102

NETGEAR ReadyNAS 104

NETGEAR ReadyNAS 202

NETGEAR ReadyNAS 204

NETGEAR ReadyNAS 312

NETGEAR ReadyNAS 314

NETGEAR ReadyNAS 316

NETGEAR ReadyNAS 516

NETGEAR ReadyNAS 716X

NETGEAR EDA 500

Disks

Defaults and Technical

Specifications

Key Features

Related manuals

Frequently Answers and Questions

What is the maximum storage capacity of the Seagate RN10400-100EUS?

What type of processor does the Seagate RN10400-100EUS use?

How much memory does the Seagate RN10400-100EUS have?

What type of RAID support does the Seagate RN10400-100EUS offer?

What operating system does the Seagate RN10400-100EUS use?

Does the Seagate RN10400-100EUS come with a warranty?

Table of contents

Seagate RN10400-100EUS User manual

ReadyNAS OS 6 Desktop Storage

Systems

Hardware Manual

Contents

Getting Started

NETGEAR ReadyNAS 102

NETGEAR ReadyNAS 104

NETGEAR ReadyNAS 202

NETGEAR ReadyNAS 204

NETGEAR ReadyNAS 312

NETGEAR ReadyNAS 314

NETGEAR ReadyNAS 316

NETGEAR ReadyNAS 516

NETGEAR ReadyNAS 716X

NETGEAR EDA 500

Disks

Defaults and Technical

Specifications

Key Features

Related manuals

Netgear

ReadyNAS 102

Netgear

ReadyNAS 312

Netgear

ReadyNAS OS 6 Desktop Storage Systems

Netgear

RN10200

Netgear

EDA500 – ReadyNAS Expansion Chassis 5-Bay, Diskless

Netgear

ReadyNAS OS 6.2

Netgear

ReadyNAS 4220 Series

Netgear

ReadyNAS

Netgear

ReadyNAS OS 6 Desktop Storage Systems

Netgear

ReadyNAS 214

Netgear

READYNAS DUO

Netgear

ReadyNAS 2120

Frequently Answers and Questions

What is the maximum storage capacity of the Seagate RN10400-100EUS?

What type of processor does the Seagate RN10400-100EUS use?

How much memory does the Seagate RN10400-100EUS have?

What type of RAID support does the Seagate RN10400-100EUS offer?

What operating system does the Seagate RN10400-100EUS use?

Does the Seagate RN10400-100EUS come with a warranty?

Table of contents