TOYOTA CAMRY 2007 - TVIP V2 (GBS WITH ADD ON) Part Number

TOYOTA CAMRY 2007 - TVIP V2 (GBS WITH ADD ON) Part Number
TOYOTA
CAMRY
2007 -
TVIP V2 (GBS WITH ADD ON)
Preparation
GLASS BREAKAGE SENSOR
NOTE: Part number of this accessory may not be
the same as the part number shown.
General Applicability
Part Number: 08586-3T930
Kit Contents
Item #
1
Quantity Reqd.
2
2
3
4
1
1
1
Description
Wire Harness (One wire
harness is only for RS3200+)
GBS ECU
GBS Mounting Bracket
Microphone
Note: Camry with factory TDS system only
Recommended Sequence of Application
Item #
1
2
Accessory
V2/V4
Satellite Radio
Hardware Bag Contents
Item #
1
2
3
4
5
6
7
8
9
10
Quantity Reqd.
1
4
30
2
2
1
1
1
1
1
Description
Self-tapping Screw
Small Foam Tapes
Wire Ties
Window Labels for RS3200+
Window Labels for GBS
Owner’s Manual for RS3200+
Owner’s Manual for GBS
M6 Nut
Key Tag
Warranty Card
Additional Items Required For Installation
Item #
1
Quantity Reqd.
1
Description
Electrical Tape
Conflicts
Recommended Tools
Personal & Vehicle
Protection
*Mandatory
Vehicle Service Parts (may be required for reassembly)
Item #
(Optional)
Blankets, Part Boxes
Special Tools
Notes
Striker Tool (PPO only)
CAD-E IADS P/N:
ALL 02-016-01
Installation Tools
Notes
Phillips Head Screwdriver
Flat Blade Screwdriver
Socket
Nylon Panel Removal Tool
#2, screwdriver or tip
Small
10 mm
e.g. Panel Pry Tool #1
STOP: Damage to the vehicle may occur. Do not
proceed until process has been complied with.
OPERATOR SAFETY: Use caution to avoid risk of
injury.
CAUTION: A process that must be carefully observed
in order to reduce the risk of damage to the
accessory/vehicle and to ensure a quality installation.
TOOLS & EQUIPMENT: Used in Figures calls out the
specific tools and equipment recommended for this
process.
Toyota SST # 00002-06001-01
Pneumatic/Electric Wrench
Wrench
Torque Wrench
Side Cutters
10 mm
Special Chemicals
Notes
Cleaner
Glass Cleaner
VDC Approved Cleaner
Household Windex
Issue: B
03/08/06
Description
Legend
Notes
Safety Glasses
Safety Gloves
Vehicle Protection
Quantity Reqd.
Page 1 of 17 pages
TOYOTA
CAMRY
2007 -
TVIP V2 (GBS WITH ADD ON)
Procedure
GLASS BREAKAGE SENSOR
Care must be taken when installing this accessory to ensure damage does not occur to the vehicle. The installation of this
accessory should follow approved guidelines to ensure a quality installation.
These guidelines can be found in the "Accessory Installation Practices" document.
This document covers such items as:• Vehicle Protection (use of covers and blankets, cleaning chemicals, etc.).
• Safety (eye protection, rechecking torque procedure, etc.).
• Vehicle Disassembly/Reassembly (panel removal, part storage, etc.).
• Electrical Component Disassembly/Reassembly (battery disconnection, connector removal, etc.).
Please see your Toyota dealer for a copy of this document.
Negative Battery Cable
10mm Wrench
1. Vehicle Disassembly.
(a) Remove the negative battery cable.
(Fig. 1-1)
Battery
(1) Protect the fender before starting.
(2) Be careful not to touch the positive
terminal.
Fig. 1-1
(b) Remove the glove-box under-dash cover.
(Fig. 1-2)
Nylon Panel Removal Tool
Under-Dash Cover
Fig. 1-2
Nylon Panel Removal Tool
l
Step Cover
Fig. 1-3
Issue: B
(c) Remove the passenger’s step cover.
(Fig. 1-3)
03/08/06
Page 2 of 17 pages
TOYOTA
CAMRY
2007 -
TVIP V2 (GBS WITH ADD ON)
Procedure
GLASS BREAKAGE SENSOR
Nylon Panel Removal Tool
Cowl Cover
(d) Remove the nut securing the passenger’s
cowl cover, then remove the cowl cover.
(Fig. 1-4)
Nut
Fig. 1-4
(e) Remove one screw and one bolt from the
glove box assembly. (Fig. 1-5)
Glove Box
Assembly
Screw
Bolt
Fig. 1-5
Phillips Screwdriver
Screws (x3)
(f) Remove the glove box assembly. (Fig. 1-6)
(1) Open the glove box door and remove
three screws securing the glove box
assembly.
Glove Box Assembly
Fig. 1-6
(g)
Disconnect the trunk opener cancel switch
from the glove box assembly if equipped.
FOR VEHICLES WITHOUT SMART ENTRY
SYSTEM ONLY. (Step h)
Nylon Panel Removal Tool
NOTE: Do not perform this step if the vehicle
has Smart Entry.
(h) Remove the driver’s step cover. (Fig. 1-7)
Step
Cover
Fig. 1-7
Issue: B
03/08/06
Page 3 of 17 pages
TOYOTA
CAMRY
2007 -
TVIP V2 (GBS WITH ADD ON)
Procedure
GLASS BREAKAGE SENSOR
FOR VEHICLES WITHOUT SMART ENTRY
SYSTEM ONLY. (Steps i-l)
NOTE: Do not perform this step if the vehicle
has Smart Entry.
Cowl Cover
(i) Remove the driver’s cowl cover. (Fig. 1-8)
Nut
Fig. 1-8
(j) Remove one bolt and one screw. Then,
loosen the lower dash cover. (Fig. 1-9)
10mm Wrench, Phillips Screwdriver, Nylon
Panel Removal Tool
Hood Release Latch
(k) Remove the hood release cable. (Fig. 1-9)
(1) Do not bend the hood release cable.
Cable
Fig. 1-9
Bolt
Nylon Panel Removal Tool
Screw
(l) Remove the lower dash cover. (Fig. 1-10)
Aspirator Hose
(1) Disconnect the temperature sensor
(connector and aspirator hose) from the
lower dash cover if equipped.
2. V2 Harness Installation Preparation
FOR VEHICLES WITHOUT SMART ENTRY
SYSTEM ONLY. (Step a)
Lower Dash Cover
Fig. 1-10
V2 Harness’
YELLOW
Wire
Cut!
20 mm
Connector
Microphone
Harness
V2 Harness’
YELLOW
Wire
White Tape
Part Number Label
Fig. 2-1
Issue: B
03/08/06
Electrical
Tape
NOTE: Do not perform this step if the vehicle
has Smart Entry.
(a) Locate the V2 harness’ YELLOW wire. Near
the white tape marker, cut the V2 harness’
YELLOW wire 20 mm from the bottom
branch of the wire. (Fig. 2-1)
(1) Do not cut other wires.
(2) Turn the V2 harness’ YELLOW wire,
and then bind it up to the V2 harness’
with the electrical tape. (Fig. 2-1)
Page 4 of 17 pages
TOYOTA
CAMRY
2007 -
TVIP V2 (GBS WITH ADD ON)
Procedure
GLASS BREAKAGE SENSOR
Side Cutter
3. V2 Harness Installation
Bolt
Wire Tie
V2 Harness
V2 Harness’
2P Connector
(a) Locate the passenger side airbag assembly.
Locate the V2 harness’ white tape marker,
and the vehicle harness, and secure together
with one wire tie, in line with the bolt of the
airbag assembly on the right side. (Fig. 3-1)
FOR SMART ENTRY VEHICLES ONLY.
(Steps b-e)
Fig. 3-1
28P (White)
V2 Harness
NOTE: Only perform this step on Smart Entry
vehicles.
(b) Locate and disconnect the white 28P
connector from the smart key ECU.
(Fig. 3-2)
(c) Using a small jeweler’s screwdriver lift up
the terminal retainer on the back of the white
28P connector. (Fig. 3-3)
Smart Key ECU
(1) Do not pull out the retainer.
Fig. 3-2
Jeweler’s Screwdriver
28P Connector
Tab
(d) Insert the terminal at the end of the V2
harness’ YELLOW wire into the bottom row,
seventh space from the left of the vehicle
harness’ 28P connector. (Fig. 3-3)
(1) Turn the connector so the wire faces you
and the tab is on top.
(2) Verify the correct opening is chosen; and.
the terminal is inserted and seated
properly.
Fig. 3-3
Side Cutter
V2 Harness
28P (White)
Wire Ties (x2)
Smart Key ECU
Fig. 3-4
Issue: B
Microphone Connector
03/08/06
(3) The terminal should not come out when
pulled lightly from the back. If the
terminal comes out, push it in further
until securely seated.
(e) Reconnect the 28P connector to the smart
key ECU. (Fig. 3-4)
(f) Route and secure the V2 harness to the
vehicle harness with two wire ties. (Fig. 3-4)
Page 5 of 17 pages
TOYOTA
CAMRY
2007 -
TVIP V2 (GBS WITH ADD ON)
Procedure
GLASS BREAKAGE SENSOR
(g) Route the V2 harness downward towards the
blower assembly then secure it to the bottom
of the blower assembly vehicle harness with
three wire ties. (Fig. 3-5)
Side Cutter
Blower
Assembly
Wire Tie
V2 Harness’ 2P
Connector
Wire Ties (x2)
V2 Harness
Fig. 3-5
Side Cutter
(h) Route the V2 harness’ blue 20P connector
and ground wire terminal toward the
passenger side cowl area. (Fig. 3-6)
V2 Harness
V2 Harness’
Ground Wire
Terminal
20P Connector
(Blue)
Fig. 3-6
Side Cutter
Vehicle
Harness
V2
Harness
(i) Secure the V2 harness to the cowl, securing it
between the reinforcement brace and bracket
with one wire tie as shown. (Fig. 3-7)
Wire Tie
Fig. 3-7
10mm Wrench
Bolt
Vehicle
Harness’
Ground Wire
Terminal
(j) Locate and remove the vehicle’s ground bolt
from the right side of the glove box area.
(Fig. 3-8)
(1) Do not discard the bolt.
Fig. 3-8
Issue: B
03/08/06
Page 6 of 17 pages
TOYOTA
CAMRY
2007 -
TVIP V2 (GBS WITH ADD ON)
Procedure
GLASS BREAKAGE SENSOR
10 mm Wrench
V2 Harness
V2 Harness’
Ground
Terminal
Bolt
(k) Secure the V2 harness’ ground wire terminal,
along with the vehicle harness’ ground wire
terminals, using the existing bolt. (Fig. 3-9)
(1) Verify the bolt is tightened securely.
Vehicle Ground
Terminal
Fig. 3-9
(l) Locate and disconnect the vehicle harness’
blue 20P connector from the passenger side
cowl area. (Fig. 3-10)
20P (Blue)
Fig. 3-10
Vehicle
Harness’
20P (Blue)
V2 Harness
V2 Harness’
20P (Blue)
(m) Plug in the V2 harness’ blue 20P connector
between the vehicle harness’ 20P connector
and the connector block. (Fig. 3-11)
V2 Harness’
Fig. 3-11 20P (Blue)
Side Cutter
Wire Ties
(x3)
V2 Harness
(n) Secure the V2 harness to the vehicle harness
with three wire ties. (Fig. 3-12)
20P (Blue)
Fig. 3-12
Issue: B
03/08/06
Page 7 of 17 pages
TOYOTA
CAMRY
2007 -
Procedure
TVIP V2 (GBS WITH ADD ON)
GLASS BREAKAGE SENSOR
4. V2 ECU Preparation and Installation.
Flat Blade Screwdriver
(a) Turn the adjustment screw on the GBS ECU
to the “10” position. (Fig. 4-1)
V2 ECU
Fig. 4-1
ECU Bracket
Side Cutter
Cut!
(b) Cut the small foam tape into two pieces.
Attach both pieces of the small foam tape to
the ECU bracket as shown. (Fig. 4-2)
Small Foam
Tape
Small Foam
Tape
Fig. 4-2
(c) Insert the ECU mounting bracket into the
indicated bracket slots on the GBS ECU.
(Fig. 4-3)
GBS ECU
ECU
Mounting
Bracket
CAUTION: The bracket is permanently
attached once installed.
Fig. 4-3
10mm Wrench
(d) Plug the V2 harness’ 8P connector into the
GBS ECU. (Fig. 4-4)
8P Connector
GBS ECU
V2 Harness
Stud Bolt
ECU Bracket
Nut
Fig. 4-4
Issue: B
03/08/06
(e) Locate the counter rotation hole and the hole
on the vehicle brace. Mount the GBS ECU
assembly as shown, using the supplied selftapping screw. If the vehicle has a stud bolt,
the bracket is secured using the supplied nut,
instead of the self-tapping screw. (Fig. 4-4)
Page 8 of 17 pages
TOYOTA
CAMRY
2007 -
TVIP V2 (GBS WITH ADD ON)
Procedure
GLASS BREAKAGE SENSOR
GBS ECU
Side Cutter
(f) Connect the V2 harness to the GBS ECU.
Secure the V2 harness to the vehicle harness
with four wire ties. (Fig. 4-5)
V2 Harness
CAUTION: Leave a small amount of slack
in the V2 harness.
Wire Ties (x4)
FOR VEHICLES WITH SMART ENTRY
SYSTEM ONLY. (Steps g-h)
Fig. 4-5
V2 Harness’
BLUE Wire
NOTE: Only perform this step on Smart Entry
vehicles.
(g) Locate the V2 harness’ BLUE and RED
wires. Separately wrap the terminal at the
end of each wire with electrical tape.
(Fig. 4-6)
V2 Harness’
RED Wire
Fig. 4-6
Side Cutter
V2 Harness
(h) Bundle up the excess of the V2 wire harness
and secure it to the vehicle brace with three
wire ties. (Fig. 4-7)
Go to Section 5.
Wire Ties (x3)
Fig. 4-7
FOR VEHICLES WITHOUT SMART ENTRY
SYSTEM ONLY. (Step i)
Side Cutter
NOTE: Only perform this step if the vehicle
does not have Smart Entry.
(i) Route the V2 harness behind the center
console to the driver’s side, and secure with
two wire ties. (Fig. 4-8)
Fig. 4-8
Issue: B
Wire Ties (x2)
03/08/06
Page 9 of 17 pages
TOYOTA
CAMRY
2007 -
TVIP V2 (GBS WITH ADD ON)
Procedure
GLASS BREAKAGE SENSOR
Side Cutter
V2 Harness
Wire Tie
Knee Air Bag
Assembly
Air
Conditioner
Duct
Fig. 4-9
Small Foam Tape
Air Conditioner
Duct
Side Cutter
Air Conditioner
Metal Pipes
Fig. 4-10 Steering Shaft
Side Cutter
V2 Harness’
WHITE/BLACK
AND BLUE
Wires
Instrument
Panel J/B
(m) Insert the terminal at the end of the V2
harness’ BLUE wire into the first space on
the top from the left of the retainer.
(Fig. 4-12)
(1) Turn the connector so the wires face you
and the retainer is on top.
(2) Verify the correct opening is chosen.
WIRE SIDE VIEW
26P
Connector
03/08/06
(l) Route the V2 harness up toward the
instrument panel J/B, then secure it to the
vehicle harness with five wire ties.
(Fig. 4-11)
edges.
Pliers
Issue: B
(k) Route the V2 harness towards the air
conditioner duct and behind the steering shaft
and secure to the vehicle harness with two
wire ties. (Fig. 4-10)
secured so that it does not contact any sharp
Wire Ties (x3)
Fig. 4-12
NOTE: Only perform this step if the vehicle
does not have Smart Entry.
(j) Continue routing the V2 harness and secure
to the knee air bag assembly and secure with
one wire tie. Route towards the air
conditioner duct and apply one piece of small
foam tape to it, securing the V2 harness to
the duct. (Fig. 4-9)
CAUTION: Ensure the V2 harness is routed and
V2 Harness
Wire Ties
(x2)
Fig. 4-11
FOR VEHICLES WITHOUT SMART ENTRY
SYSTEM ONLY. (Steps j-m)
Backside of
Instrument
Panel J/B
(3) Verify the terminal is inserted and seated
properly. The terminal should not come
out when pulled lightly from the back. If
the terminal comes off, then push it in
again.
Page 10 of 17 pages
TOYOTA
CAMRY
2007 -
TVIP V2 (GBS WITH ADD ON)
Procedure
GLASS BREAKAGE SENSOR
FOR VEHICLES WITHOUT SMART ENTRY
SYSTEM ONLY. (Step n)
Side Cutter
NOTE: Only perform this step if the vehicle
Wire Tie (x2)
does not have Smart Entry.
26P Connector
V2 Harness
Fig. 4-13
(n) Continue routing the V2 harness, and secure
it to the wires of the backside of the
instrument panel junction block with two
wire ties. (Fig. 4-13)
5. Microphone Installation
Microphone 2P
(a) Using VDC approved cleaner and cleaning
method, clean the area indicated on the
backside of the glove box under cover.
(Fig. 5-1)
(1) When cleaning with the VDC approved
cleaner, follow the manufacturer’s
directions. Do not allow cleaner to air
dry.
Glove Box
Under Cover
Fig. 5-1
Small Foam Tape
(2) Remove the backing sheet and secure the
microphone to the backside of the glove
box under cover.
(3) Secure the microphone as shown.
(4) Do not touch the adhesive surface of the
microphone.
(5) Press the microphone to the glove box
under cover firmly.
Microphone 2P
Connector
Fig. 5-2
Glove Box
Under Cover
V2 Harness’ 2P
Microphone 2P
(1) Do not cover the opening of the
microphone with the foam tape.
(c) Plug in the V2 harness’ white 2P connector
to the microphone’s white 2P connector.
(Fig. 5-3)
(1) Verify the connectors are plugged in
securely.
Fig. 5-3
Issue: B
(b) Secure the microphone with one small strip
of foam tape. (Fig. 5-2)
03/08/06
Page 11 of 17 pages
TOYOTA
CAMRY
2007 -
TVIP V2 (GBS WITH ADD ON)
Procedure
GLASS BREAKAGE SENSOR
(d) Reinstall the glove box under cover. Ensure
that the V2 harness does not interfere with
moving parts. (Fig. 5-4)
Nylon Panel Removal Tool
6. Warning Label Installation.
(a) Using household Windex, clean the inside
surface of the front door windows.
(Fig. 6-1)
Under-Dash Cover
Fig. 5-4
Warning Label
(1) Use the red TVIP label, which is the GBS
label.
10mm
(b) Place the warning label on the inside surface
of the front door’s windows as shown.
(Fig. 6-1)
Line Up With
Bottom of Window
Etching
(c) Use a piece of clean adhesive tape to lift the
labels off their protective backing sheet.
(1) Do not touch the adhesive surface of the
warning labels.
Fig. 6-1
(d) Line up the labels properly and place on the
glass once; do not use a label that was pulled
off of the glass.
Torque Wrench, 10mm Socket
Negative
Battery
Cable
7. Completing the Installation.
(a) Complete the reassembly of the vehicle.
Battery
(1) Reconnect any disconnected connectors.
(2) Verify the panels fit together properly
with no uneven gaps between them.
Fig. 7-1
(3) Reconnect the vehicle’s negative battery
cable. (Fig. 7-1)
(4) Position the negative battery cable at the
original factory position.
(5) Tighten the nut to 36 in-lbf. + 1.5.
(6) Do not touch the positive terminal with
any tool when replacing the cable.
(b) Reset the power windows.
Issue: B
03/08/06
Page 12 of 17 pages
TOYOTA
CAMRY
2007 -
TVIP V2 (GBS WITH ADD ON)
Procedure
GLASS BREAKAGE SENSOR
(c) Turn the ignition key to “ON.”
(d) Reset the power moon roof.
(1) Press and hold the moon roof button until
the moon roof is closed. Hold for two (2)
additional seconds.
(e) Place the owner’s manual, left in its
protective bags, in the glove box.
Issue: B
03/08/06
Page 13 of 17 pages
TOYOTA
CAMRY
2007 -
TVIP V2 (GBS ADD ON)
Checklist - these points MUST be checked to ensure a quality installation.
Check:
Look For:
Accessory Function Checks
Roll up all windows, and exit the vehicle
with remote.
Press and release the remote control’s lock
button to start the arming process.
1.
Wait 30 seconds.
After 30 seconds, the LED starts flashing;
the system is now armed.
Perform the following check in a
temperature-controlled environment
(50º-90º F)
Issue: B
03/08/06
Page 14 of 17 pages
TOYOTA
CAMRY
2007 -
TVIP V2 (GBS ADD ON)
Checklist - these points MUST be checked to ensure a quality installation.
Check:
Look For:
With the tip of a key (or striker tool pulled
all the way out [PPO only]), tap the center
2.
The horn sounds repeatedly.
3. The headlights flash repeatedly.
of the driver’s door window to trigger the
The turn signal lights flash repeatedly.
“warn away” alarm.
The LED lights up.
NOTE: Adjust as necessary by increasing
the GBS setting to the next level if the
alarm does not trigger during the functional
verifications.
NOTE: If you do not disarm the system,
the alarm will last 20 seconds. It is not
necessary to check the alarm duration.
For all vehicles, press the unlock button of
4.
the remote key to stop the alarm.
The horn stops sounding.
All the lights stop flashing and / or turn off.
The security LED turns off.
Vehicle Function Checks
Head Lights
Functioning Head Lights
High Beams
Functioning High Beams
Turn Signal Lights
Functioning Turn Signal Lights
Tail Lights
Issue: B
Functioning Tail Lights
Stop Lights
Functioning Stop Lights
Backup Lights
Functioning Backup Lights
Hazard Lights
Functioning Hazard Lights
Marker Lights
Functioning Marker Lights
Dome/Courtesy Lights
Functioning Dome/Courtesy Lights
Panel/Switch Illumination
Functioning Panel/Switch Illumination
03/08/06
Page 15 of 17 pages
TOYOTA
CAMRY
2007 -
TVIP V2 (GBS ADD ON)
Checklist - these points MUST be checked to ensure a quality installation.
Check:
Look For:
Accessory Controls/Illumination (if
Functioning Accessory
equipped)
Key Sensor Buzzer
Functioning Key Sensor
Fog Lights (if equipped)
Functioning Fog Lights
Daytime Running Lights (if equipped)
Functioning DR Lights
Trunk/Tailgate/Bed Lights (if equipped)
Functioning Lights
Glove Box Light (if equipped)
Functioning Glove Box Light
Cruise Control Light (if equipped)
Functioning Cruise Control Light
Seat Belt Warning Light
Functioning Seatbelt Warning Light. If the
warning light remains on, it may indicate a
system malfunction.
Air Bag Warning Light
Functioning Air Bag Warning Light. If the
warning light remains on, it may indicate a
system malfunction.
ABS Light (if equipped)
Functioning ABS Light. If the warning
light remains on, it may indicate a system
malfunction.
Lamp Failure Sensor (if equipped)
Functioning Lamp Failure Light. If the
warning light remains on, it may indicate a
system malfunction.
Track/Skid Control Light (if equipped)
Functional Track/VSC Light. If the warning
light remains on, it may indicate a system
malfunction.
Issue: B
HVAC Controls
Functioning HVAC Controls
Power Locks (if equipped)
Functioning Power Locks
Power Windows (if equipped)
Functioning Power Windows
Power Seats (if equipped)
Functioning Power Seats
03/08/06
Page 16 of 17 pages
TOYOTA
CAMRY
2007 -
TVIP V2 (GBS ADD ON)
Checklist - these points MUST be checked to ensure a quality installation.
Check:
Look For:
Power Sunroof (if equipped)
Functioning Sunroof
Horn
Functioning Horn
Gauges
Functioning Gauges
Front Wiper/Washer
Functioning Front Wiper/Washer
Rear Wiper/Washer (if equipped)
Functioning Rear Wiper/Washer
Clock (if equipped)
Functioning Clock
Accessory Power Socket (if equipped)
Functioning Power Socket
Starter
Functioning Starter
Audio/Video (if equipped)
Functioning Audio/Video
Power Sliding Door (if equipped)
Functioning Power Sliding Door
Convenience Memory Settings (if
Functioning Memory Settings
equipped)
Functioning Heated Seats
Heated Seats (if equipped)
Functioning Massage Seats
Massage Seats (if equipped)
Functioning Rear Window Defogger
Rear Window Defogger (if equipped)
Power Side Mirrors (if equipped)
Functioning Side Mirror Defogger
Side Mirror Defogger (if equipped)
Functioning Front Windshield Defogger
Front Windshield Defogger (if equipped)
Functioning Navigation System
Navigation System (if equipped)
Functioning Rear Sunshade
Rear Sunshade (if equipped)
Remove the appropriate fuse after
checks are completed.
Issue: B
Functioning Power Side Mirrors
03/08/06
Page 17 of 17 pages
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement