- Vehicles & accessories
- Motor vehicle accessories & components
- Car seat
- Mattel
- DELUXE PLUS HEALTHY CARE B0325
- User manual
advertisement
Deluxe Healthy Care
™
High Chair
Product features and decoration may vary from the photo above.
Model Number: B2105, B0326
Please keep this instruction sheet for future reference, as it contains important information.
Adult assembly is required.
Tool needed for assembly: Phillips Screwdriver (not included).
Discover what’s pos sible
™ …ww w.fis
herpric e.c
om
Warnings and Caution
WARNING
Prevent serious injury or death from falls or sliding out.
• The child should be secured in the high chair at all times by the restraining system, either in the recline, semi-recline or upright position. The restraint belts must be adjusted to fit your child snugly. The tray is not designed to hold the child in the chair.
• Always leave wheels locked.
• Never use near stairs.
• Always keep child in view while in the high chair.
• Never leave child unattended.
• It is recommended that the high chair be used in the upright position only by children capable of sitting upright unassisted.
Consumer Information
Occasionally a consumer may experience a problem with one of our products. If this should happen, please call us toll-free, rather than return this product to the store. Usually, we can solve the problem over the telephone or send you replacement parts. Please call Fisher-Price® Consumer Relations, toll-free at 1-800-432-5437, 8 AM - 6 PM EST Monday through Friday. Hearing-impaired consumers using TTY/TDD equipment, please call 1-800-382-7470. Or, write to:
Fisher-Price®
Consumer Relations
636 Girard Avenue
East Aurora, New York 14052
CAUTION
This product contains small parts in its unassembled state.
Adult assembly is required.
2
Parts
Headrest
3 Food Trays
Pad
#8 x 3
Frame
Seat Back
Seat
Bottom
/
4
" Screws
#8 x 3 /
4
"
Screws
Footrest
Base Tray
Hinge
Rod
#10 x 7 /
8
"
Black Screw
Storage
Caddy
2 Seat Bottom Tubes
4 Screw Retainers
#10 x 7 /
8
"
Black Screw - 4
Back Base
Frame
#8 x 3 /
4
" Screws
4 Wheels
#10 x 7 /
8
"
Black Screws
Front Base
#8 x 3 /
4
" Screw - 8
SHOWN ACTUAL SIZE
#10 x 7 /
8
" Black Screw - 7
SHOWN ACTUAL SIZE
3
Assembly
IMPORTANT! Before assembly, inspect this product for damaged hardware, loose joints, missing parts or sharp edges. DO NOT use if any parts are missing or broken.
Contact Fisher-Price® for replacement parts and instructions if needed. Never substitute parts.
Footrest
Seat
Bottom
Tubes
Plastic
Rings
1
Seat Bottom
• Place the seat bottom face down on a flat surface.
• At an angle, fit the footrest on the seat bottom, as shown.
Seat Bottom Tubes
Plastic
Rings
Plastic
Rings
Plastic
Rings
3
• Align the holes in the plastic rings and the seat bottom tubes.
• Insert a #8 x 3 /
4
" screw through each plastic ring and into the seat bottom tubes, as shown.
#8 x 3
SHOWN ACTUAL SIZE
• Tighten the screws with a Phillips screwdriver.
Do not over-tighten.
/
4
" Screw - 4
• Push the seat bottom tubes back and forth to be sure they are secured to the seat bottom. If the seat bottom tubes move, you have probably not fastened them properly.
Remove the screws and check to be sure the screw holes in the seat bottom tubes and seat bottom plastic rings are aligned. Replace and tighten the screws.
Footrest
Insert Screws
Here
2
• Slide a seat bottom tube through each set of plastic rings on the seat bottom.
4
4
• Insert two #10 x 7 /
8
" black screws through the footrest and into the seat bottom.
#10 x 7 /
8
" Black Screw - 2
SHOWN ACTUAL SIZE
• Tighten the screws with a Phillips screwdriver.
Do not over-tighten.
Assembly
Frame Leg
Seat Back
Pin
Opening
Seat Back
Pin
Opening
Seat
Bottom
Assembly
5
• Turn the seat bottom assembly upright.
• Fit the seat back pins into the openings in the top side of the seat bottom assembly.
7
• Pull the frame leg out on each frame to open. Make sure it
“clicks” into place.
Short Leg
Tube
Hinge
#10 x 7 /
8
" Black Screw
SHOWN ACTUAL SIZE
Hinge Rod
Long
Tapered
Leg Tube
Back Base
8
6 Front Base
• Turn the seat assembly face down.
• Insert the hinge rod through the hinge on the seat back and seat bottom, as shown.
• Insert a #10 x 7 /
8
" black screw into the hinge rod.
• Tighten the screw with a Phillips screwdriver.
Do not over-tighten.
• Set the seat assembly aside for Assembly step 11.
5
• Identify the back and front base. The back base has short leg tubes and the front base has long, tapered leg tubes. You will use the back base for the next assembly step.
Assembly
Frame
Decorated
Side
Seat Height
Adjusters
Position 4
Frame
Back
Legs
9
Back Base Hole
Screw
Retainers
Back Base Hole
Press Lever
10
• While pressing the levers on the seat height adjusters, lift them to position 4 on the frame front legs, as shown.
Seat Assembly
#10 x 7 /
8
" Black Screw - 2
SHOWN ACTUAL SIZE
Screw Retainer - 2
• Position a frame so that the decorated side is outward.
• Insert the back leg of a frame into the back base.
• Fit a screw retainer over the hole in the back base, as shown.
• Insert a #10 x 7 /
8
" black screw through the screw retainer and back base.
• Tighten the screw with a Phillips screwdriver. Do not over-tighten.
• Repeat this procedure to attach the other frame back leg to the other side of the back base.
Sockets
11
Seat Bottom
Tubes
Sockets
6
• Fit the seat assembly between the two frames.
• Insert the seat bottom tubes into the sockets in each seat height adjuster.
Hints:
• Be sure the seat height adjusters are in the same position
(position 4).
• You may need to push the frames apart slightly to fit the seat bottom tubes into the seat height adjuster sockets.
Assembly
Push
Seat
Height
Adjuster
Push
Seat
Height
Adjuster
Front Leg Hole
13 Seat Bottom
Tube Ends
Screw Retainers
Front Leg Hole
Front Base
#8 x 3 /
4
" Screw - 2
• Push each seat height adjuster to be sure they are completely on the seat bottom tubes.
SHOWN ACTUAL SIZE
• Insert a #8 x 3 /
4
" screw through each seat height adjuster and the ends of the seat bottom tube.
• Tighten the screws with a Phillips screwdriver.
Do not over-tighten.
12
#8 x 3 /
4
" Screw - 2
SHOWN ACTUAL SIZE
Screw Retainer - 2
#10 x 7 /
8
" Black Screw - 2
SHOWN ACTUAL SIZE
Seat
Height
Adjuster
Seat
Height
Adjuster
• Fit the frame front legs onto the front base.
• Fit a screw retainer over a hole in the front leg.
• Insert a #10 x 7 /
8
" black screw through the screw retainer and front leg.
• Tighten the screw with a Phillips screwdriver. Do not over-tighten.
• Repeat this procedure to secure the other end of the front base with the remaining screw retainer and #10 x 7 /
8
" black screw.
Seat
Bottom
Tube Ends
14
Back and
Bottom View
7
• From the back and bottom of the assembly, insert a #8 x 3 /
4
" screw through both seat height adjusters and the ends of the seat bottom tube.
• Tighten the screws with a Phillips screwdriver.
Do not over-tighten.
Assembly
Pad
Front Base
Holes
Wheels Wheels Hole
Elastic Loops
Hole
Back Base
Holes
15
Bottom View
• Tip the assembly so that the back of seat is flat on the floor and the front and back bases are facing up.
• Insert and “snap” the peg on a wheel into each of the four holes in the front and back bases.
Peg
Wheel
Hole
Hint: To remove the wheels from the front and back base, simply pull and remove. Store the wheels in a safe place for future use.
16
Tabs
8
Elastic Loops
Back and
Bottom View
• Lift the assembly upright.
• From the front of the assembly, place the pad onto the seat.
• Lift the bottom of the pad. Insert the two elastic loops on the pad through the holes in the seat bottom.
• From the back and bottom of the seat, hook the elastic loops to the tabs on the seat.
Assembly
Slot
Crotch
Belt
17
• Insert the crotch belt through the slot in the pad. Make sure the crotch belt is not twisted.
19
Pad
Bottom
Slots
• Lift the top of the pad.
• Thread the waist/shoulder belts through the bottom slots in the back of the seat pad.
Upper Shoulder Belt Slots
Shoulder
Portion
Lower Shoulder
Belt Slots
Headrest
Pad Slots
Shoulder
Portion
20
18
• Fold the top of the pad down.
• Remove the shoulder portion of the waist/shoulder belts by feeding them through the slots in the seat back.
9
• Fit the top of the pad over the seat back.
• Fold the bottom edge of the pad under the edge of the seat bottom to fasten it.
• First, insert the shoulder portion of the shoulder/waist belt through the slots in the headrest pad. Then, insert the shoulder portion of the shoulder/waist belt through the slots in the pad and seat back.
- Use the lower shoulder belt slots for a smaller baby.
- Use the upper shoulder belt slots for a larger baby.
Assembly
Headrest
Pad Strap
Handle
Elastic
Loop
Tab
Belt
Ends
Elastic
Loop
Tab
21
• Fit the strap on the top of the headrest through the handle.
23
Back View
• From behind the seat, be sure the shoulder portion of the waist/shoulder belts are secure in the seat back slots.
• Hook the elastic loops on each side of the pad onto the tabs in the seat back.
Handle Pad
Strap
Headrest Strap
Small
Fastener
Storage
Caddy
Frame
Tab
Large
Fastener
22
Back View
• Fit the pad strap through the handle and press it to the
small fastener on the back of the seat.
• Fit the headrest strap through the handle and press it to the
large fastener on the back of the seat.
24
10
• At an angle, fit the storage caddy onto the tab on either frame.
Assembly is now complete.
Securing Your Child
IMPORTANT! Before each use, inspect this product for damaged hardware, loose joints, missing parts or sharp edges. DO NOT use if any parts are missing or broken.
Contact Fisher-Price® for replacement parts and instructions if needed. Never substitute parts.
WARNING
Prevent serious injury or death from falls or sliding out.
The child should be secured in the high chair at all times by the restraining system, either in the recline, semi-recline or upright position. The restraint belts must be adjusted to fit your child snugly.
The tray is not designed to hold the child in the chair.
Anchored
End
A
B
Free End
Buckle
2
Tighten
Anchored
End
A
B
Free End
Loosen
To tighten the waist belts:
• Feed the anchored end of the waist belt up through the buckle to form a loop A .
• Pull the free end of the waist belt B .
• Repeat this procedure to tighten the other waist belt.
To loosen the waist belts:
• Feed the free end of the waist belt up through the buckle to
• Enlarge the loop by pulling on the end of the loop toward the buckle.
• Pull the anchored end of the waist belt to shorten the free end of the waist belt B .
• Repeat this procedure to loosen the other waist belt.
Waist/Shoulder
Belt
Waist/Shoulder
Belt
Hold
Adjuster
Pull Strap
Down
Slide
Adjuster
Down
Crotch
Belt
3
1 Tighten Loosen
• Place your child in the seat. Position the crotch belt between your child’s legs.
• Fasten both waist/shoulder belts to each side of the crotch belt. Make sure you hear a "click" on both sides.
• Check to be sure the restraint system is securely attached by pulling it away from your child. The restraint system should remain attached.
11
To tighten the shoulder belts: Hold the adjuster and pull the front shoulder strap down.
To loosen the shoulder belts: Slide the adjuster down.
Note: After adjusting the restraint system to fit your child, make sure you pull on it to be sure it is securely fastened.
Securing Your Child
4
To change shoulder belt slots:
• From the back of the high chair, push the shoulder portion of the waist/shoulder belts through the seat back slots.
Shoulder
Portion
Using the Trays
WARNING
Prevent serious injury or death from falls or sliding out.
The child should be secured in the high chair at all times by the restraining system, either in the recline, semi-recline or upright position. The restraint belts must be adjusted to fit your child snugly.
The tray is not designed to hold the child in the chair.
Base Tray
Armrest
Armrest
5
6
• From the front of the high chair, pull the shoulder portion of the waist/shoulder belts out and then fit them back through the desired shoulder belt slots in the headrest pad, seat pad
and the seat back. Pull on the belts to be sure they are secure in the seat back.
12
• Fit the base tray onto the seat armrests. Push down until the base tray "snaps" into place.
Hint: Before use, thorougly wash all parts (the trays) that may contact food.
Using the Trays
Hint: The base tray can be adjusted for your child’s comfort two ways (see steps 7 and 8)!
Hint: The base tray can be removed two ways (see steps
9 and 10)!
Base
Tray
Squeeze
Latch
Base
Tray
Squeeze
Latch
Release Bar
7
9
• While pushing the release bar on the front of the base tray, adjust the base tray forward or backward.
• Squeeze one or both of the latches underneath the base tray and lift.
Base
Tray
Squeeze
Latch
Base
Tray
Squeeze
Latch
Release
Bar
8
10
• While squeezing the latches underneath the base tray, adjust the base tray forward or backward.
13
• While pushing the release bar on the front of the base tray, pull the tray base towards you and remove.
Using the Trays
Food Tray
Using the Brakes
WARNING
Prevent serious injury or death from falls or sliding out.
• Always leave wheels locked.
• Never use near stairs.
Base
Tray
11
• Fit the food tray into the base tray, as shown.
Hint: Before use, thorougly wash all parts (the trays) that may contact food.
14
12
Tab
Press
Tab
Wheels
Tab
Lift
Tab
Lock Unlock
TO LOCK: Press the tab on all four wheels down until you hear a “snap”.
TO UNLOCK: Lift the tab on all four wheels up.
Adjusting the Seat
WARNING
Prevent serious injury or death from falls or sliding out.
It is recommended that the high chair be used in the upright position only by children capable of sitting upright unassisted.
Hint: Adjust the seat height to any of seven positions!
Hint: Adjust the seat angle to any of three positions: Upright,
Semi-Recline or Recline.
Upright
Semi-Recline
Recline
Seat Height
Adjuster
14
Press Lever
13
To adjust the seat height:
• Press the levers on both seat height adjusters and lift or lower the seat to the desired height.
4
• Make sure both sides of the seat are adjusted to the same height.
Push the seat bottom to be sure the seat is locked in place.
To adjust the seat angle:
• Squeeze the seat back handle and push the seat back forward or, pull it backwards to the desired position.
• Push the seat back to be sure it is latched in position.
Squeeze
Back View
15
Storage
15
Base
Tray
Peg
Hole
• Fit the holes on the base tray latches onto the pegs on the back of the high chair frame.
Care
• The pad and headrest are machine washable. Wash the pad and headrest separately in cold water on the gentle cycle.
Do not use bleach. Tumble dry separately on low heat and remove promptly.
• The frame and base tray may be wiped clean using a mild cleaning solution and a damp cloth. Do not immerse the base tray.
• The food trays are dishwasher safe. Simply remove the food tray from the base tray and place in your dishwasher.
To remove the pad:
• Remove the four elastic loops from the pegs on the underside and back of the seat.
• Unfasten the pad strap and headrest strap from the seat back.
• Feed the shoulder portion of the waist/shoulder belts through the slots in the seat back, the pad and the headrest.
• Feed the waist portion of the waist/shoulder belts and crotch belt down through the slots in the seat.
• Remove the waist/shoulder belts and crotch belt through the slots in the pad.
• Unfasten the pad fasteners from the front edge of the seat bottom.
• Remove the pad.
To replace the pad and headrest: refer to Assembly steps 16-23.
IMPORTANT! Never use this product without the restraint system. Replace the waist/shoulder belts and crotch belt.
Pull Frame
Release Latch
For other countries, outside the United States:
Canada: call 1-800-567-7724, or write to: Mattel Canada Inc., 6155
Freemont Blvd. Mississauga, Ontario L5R 3W2.
Great Britain: telephone 01628 500302.
Australia: Mattel Australia Pty. Ltd., 658 Church Street,
Locked Bag #870, Richmond, Victoria 3121 Australia.
Consumer Advisory Service 1300 135 312.
New Zealand: 16-18 William Pickering Drive, Albany 1331, Auckland.
16
• With the legs all the way open, lower the seat to position 1
(the lowest position).
• Pull the frame release latches forward and push the rear legs toward the front legs.
Printed in China
Fisher-Price, Inc., a subsidiary of Mattel, Inc.
East Aurora, New York 14052, U.S.A.
©2002 Mattel, Inc. All Rights Reserved.
® and TM designate U.S. trademarks of Mattel, Inc.
B2105-0920
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement