RCR-22 - Sangean

RCR-22 - Sangean
RCR-22
GB
Version 1
Important safety instructions
1. Read and understand all safety and operating instructions before
the radio is operated.
2. Retain instruction: The safety and operating instructions should
be retained for future reference.
3. Heed warnings. All warnings on the appliance and operating
instructions should be followed.
4. Follow all operations and use instructions.
5. Water and moisture: The appliance should not be used near
water. Do not use near a bathtub, washbowl, laundry tub,
kitchen sink, wet basement, swimming pool, etc.
6. Unplug the radio from the AC power outlet before cleaning.
Use only a damp cloth for cleaning the exterior of the radio.
7. Do not place the radio on an unstable cart, stand, bracket or
table. The radio may fall, causing serious personal injury and
damage to the radio.
8. Ventilation: This radio should be situated so that its location or
position does not interfere with its proper ventilation.
For example, the radio should not be used on a bed, sofa,
rug or other soft surfaces that may block the ventilation
openings. It should not be placed in a built-in situation like
a cabinet that may reduce air flow through the ventilation
openings.
9. Power sources: The radio should be operated only from the type
of power source indicated on the marking label. If you are not
sure of the type of power supply to your home, consult your
radio dealer or power company.
1
10. Power cords: The power cord should be positioned so it is not
walked on, pinched, or items placed on top of it. Pay particular
attention to cords at plugs, convenience receptacles, and the
point where they exit from the unit. Unplug the power cord by
gripping the power plug, not the cord. Operate the radio using
only the current type of power source indicated. If you are not
sure of the type of power supply to your home, consult your
dealer or local power company.
11. Do not overload wall outlets or extension cords. This can result
in a risk of fire or electrical shock. Never insert objects of any
kind into the radio through opening. The objects may touch
dangerous voltage points or short out parts. This could cause
a fire or electrical shock.
12. If the radio is left attended and unused for long periods of time,
unplug it form the wall outlet. This will prevent damage caused
by lightning or power line surges.
13. If the radio is left unattended and unused for a long period
of time, remove the batteries. The batteries may leak and
damage furniture of your radio.
14. Do not attempt to service the receiver yourself. Removing the
cover may expose you to dangerous voltage, and will void the
warranty. Refer all servicing to authorized service personnel.
15. Object and Liquid Entry-Never push objects of any kind into this
radio through opening as they may touch dangerous voltage
points or short-out parts that could result in a fire or electric
GB
shock. Never spill liquid of any kind of product.
16. The appliance should be serviced by qualified service personnel
when:
A. The power supply cord or the plug has been damaged.
B. Objects have fallen or liquid had been spilled into the radio.
C. The radio has been exposed to rain or water.
D. The radio does not appear to operate normally or exhibits
a marked change in performance.
E. The radio has been dropped, or the enclosure damaged.
2
3
Controls
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
Time/Date/Alarm set button; Daylight Saving Time (D.S.T.) set.
Preset memories and Alarm days buttons
Tuning Up/Down and Snooze button
FM/AM (FM/MW) band selection
Time capsule
Date button
Time button, auto time set enforcement
Alarm 2 button
Alarm 1 button
Power button and Sleep timer
Nap button
Display button
Light button
LCD display
Time zone switch
Reset button
Light level control
Alarm sound level control
AUX-IN
Headphones socket
Volume control
GB
4
LCD display
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
5
Radio band and clock AM/PM display
Daylight Saving Time indicator
Time set indicator
Nap indicator
Sleep indicator and Snooze indicator
Radio controlled time signal
Auto tuning indicator
Date indicator
Day of week indicator
Month/Date/Year/alarm time indicator
Time indicator/Frequency
Minute indicator
Memory and seconds indicator
Alarm AM/PM indicator
Alarm indicator
Operation
Clock
Automatic clock setting
1. Connect the plug to a wall socket, and your clock radio will
display -:- and the indicator
will flash on the display.
2. When the radio is off, press and hold Time button for more
than 4 seconds to receive Auto Time Set signal.
Manual clock setting (only if automatic setting fails)
1. Press the TIME button, and the display will show
.
2. Press the SET button, and the hour digits will flash on
the display.
3. Press the up or down button to adjust the hours.
4. Then press the SET button, and the minute digits will flash on
the display.
5. Press the up or down button to adjust the minutes.
6. Press SET button to complete the time setting.
* You can also stop the process and save the setting
anytime by pressing TIME button.
Manual date setting (only if automatic setting fails)
1. Press the DATE button then press SET button, the year digits
will flash.
2. Press the up or down button to adjust the year.
3. Press the SET button again and the month digits will flash.
4. Press the up or down button to adjust the month.
5. Press the SET button again and the date digits will flash.
6. Press the up or down button to adjust the date.
7. Preset SET button to complete the time setting.
* You can also stop the process and save the setting anytime
by pressing DATE button.
GB
6
Change 12/24 hour clock format
1. Press TIME button, and then press SET button.
2. To set 12 hour clock format, press Station preset 1, or,
to set 24 hours clock format, press Station preset 2.
3. Press Power button or TIME button to finish the setting.
D.S.T. (Daylight Saving Time)
1. When the display shows the time, press the SET button for
more than 4 seconds to set the clock 1 hour faster, and the
display will show .
2. To set the clock back from D.S.T., press the SET button for
more than 4 seconds, the will disappear.
Radio operation
Tuning into radio stations
There are 3 ways of tuning your radio:
A. Manual tuning
1. Press the Power button to turn on your radio.
2. Press the BAND button repeatedly to select AM (MW) or
FM waveband.
3. Press the up or down button to change the frequency.
4. Press the Power button again to turn off your radio.
7
B. Scan tuning
1. Press the Power button to turn on your radio.
2. Press the BAND button repeatedly to select AM (MW) or
FM waveband.
3. Press the up or down button for more 0.5 second and release,
it will tune into the next frequency with reception.
4. Press the Power button again to turn off your radio.
C. Presetting and recalling stations
Presetting stations:
1. Press the Power button to turn on your radio.
2. Press the BAND button repeatedly to select AM (MW) or
FM waveband.
3. Tune into the station that you would like to preset.
4. There are 7 preset buttons from 1 to 7. Press 1 of them and
hold for more than 2 seconds until the radio beeps, and the
station frequency will be saved into the chosen preset.
5. Repeat the procedure for the remaining presets. Your radio
has 7 presets for each AM and FM.
6. The preset can be overwritten by following the above procedure.
Recalling stations:
1. Press the BAND button for AM or FM.
2. Simply press 1 of the PRESET buttons (from 1 to 7) you would
like to tune into. And the preset number and frequency will
appear on the display.
GB
8
Alarm operation
There are 2 alarms which can be set independently. Also each
alarm can be set to wake you by buzzer or radio. When the alarm
light (alarm 1 or alarm 2 or both) is on, it means the indicated alarm
will active in 24 hours.
How to set buzzer alarm
The radio buzzer beep increases in volume every 15 seconds.
It beeps 1 minute, followed by 1 minute silence and repeat
the cycle. The buzzer will beep for 1 hour, or stop by pressing
the Power button.
The buzzer alarm volume may be adjusted through the Alarm sound
level control button on the bottom of the radio.
1. Press the Alarm 1 (or Alarm 2) button and Alarm 1 time
(or Alarm 2) time will show on the display.
2. Press the SET button, the alarm hour will show on the display.
3. Press up or down button to adjust the hour.
4. Press the SET button again and adjust the minute by pressing up
or down button.
5. Select required days of week on which the alarm will beep by
pressing day of week buttons.
6. Press the SET button again and press up or down button until
the display shows
.
7. Press the SET button to complete the setting.
* You can press the Alarm 1(or Alarm 2) button anytime to
complete the setting.
9
How to set Radio alarm
The radio alarm will sound for 1 hour, or stop by pressing the
Power button.
1. Press the Alarm 1 (or Alarm 2) button and Alarm 1 time
(or Alarm 2) time will show on the display.
2. Press the SET button, the alarm hour will show on the display.
3. Press up or down button to adjust the hour.
4. Press the SET button again and adjust the minute by pressing up
or down button.
5. Select required days of week on which the alarm will beep by
pressing day of week buttons.
6. Press the SET button again and press up or down button until
the display shows
.
7. Press the SET button again and press up or down button to
tune into the station that you wish to wake up and adjust volume.
Also press BAND button to select FM or AM (MW), then press
he SET button to complete the setting.
8. Press the Power button to switch off the radio.
9. When the radio signal is weak, the radio alarm will be
buzzer alarm.
GB
* You can press the Alarm 1(or Alarm 2) button anytime to complete
the setting.
* When it is AUX-IN, and the radio band is not set, the alarm will
be buzzer alarm.
10
Snooze function
1. To interrupt the alarm signal (radio alarm or beep alarm),
press any button on the top side of the radio (up/down/SET/
PRESET 1-7/band button). The alarm will stop for 5 minutes
and the display will show
. The snooze function can be repeat
during the period of the alarm is active.
2. Press the Power button to cancel the snooze and alarm function.
How to cancel alarms
1. Press and continue to hold the Alarm 1 or Alarm 2 button that
you wish to cancel for more than 2 seconds.
2. The symbol or will disappear from the display.
And the alarm you press will be cancelled.
3. To reactive the alarm, press and hold Alarm 1 or Alarm 2 button
that you wish to reactive, and the symbol or will appear
on the display and it will be reactive.
How to set alarm sound level
With alarm level adjustment switch 18 on the bottom of the radio,
you may adjust the alarm sound level.
Note: Alarm level adjustment works only for buzzer alarm
11
Nap timer
1. It is a countdown alarm which will sound after the time period
that you set. And the time period can be set from 10 to
120 minutes in 10 minutes steps.
2. Press the NAP button until the required time period is shown
on the display.
3. The word NAP will be shown on the display and the Nap timer
is set.
4. While the Nap timer is alarming, press the Power button to
silence the alarm.
5. To cancel the Nap timer before the time Nap time is elapsed,
press and release the NAP button until the OFF word is
appeared on the display.
Sleep timer – radio auto shut off
The Sleep timer can be set from 15-120 min. The radio will be
switch off after the time you set has elapsed.
1. When the radio is off, press and continue to hold the
button,
the radio will be switched on and the display will show the timer
GB
minutes in turn, and release the
button when the required
time is appeared. Then the Sleep timer is set.
2. To cancel the Sleep timer, press the Power button and the
symbol will be gone.
12
Time zone setting
Set TIME ZONE switch (on the bottom of the radio) to 0 position
for regular case.
For some countries where don’t provide radio controlled time
facility but able to receive radio controlled time signal from nearby
countries and the time zone is different, you may use the
TIME ZONE switch to correct the time.
For example, in Turkey which is one hour ahead of Central
European time but still can receive radio controlled time signal from
Germany (Central European time), you may use this TIME ZONE
switch to correct the local time.
If you are in USA just simply switch the TIME ZONE switch to the
time zone for where you are. There are 4 time zones:
PST (Pacific Standard Time), MST (Mountain Standard Time),
CST (Central Standard Time), or EST (Eastern Standard Time).
Display button
When the radio is on, you can switch the display between station
frequency and time by pressing the DISPLAY button.
Display backlight adjustment
Press the button to switch the display backlight to be brighter
or darker. When it is switched to darker, you can turn the button
17 (on the back of the radio) to adjust the display light to be the
most dark.
13
Headphone socket
Plus in a headphone to the Headphone socket for headphone
function, and the built-in radio speaker will be muted.
AUX IN socket
Plug in external audio devices such as CD player to the AUX IN
socket (on the side of the radio), then play your device and
press the Band button repeatedly until you see “AU” on the display.
The radio will amplify and play out the signal form your device.
Reset the radio
If your radio doesn’t operate correctly, or some display digits
are missing, press the RESET button (on the bottom of the radio)
with suitable implement for more than 2 seconds, the whole
memory will be reset as a brand-new one.
Technical data
Power supply:
110-120 Volt/50-60 Hz (USA version);
220-230 Volt/50-60 Hz (Europe version)
Output power: 800 mW (max)
GB
Power consumption: 7W (max)
Frequency coverage:
FM 87.5 – 108.0 MHz
AM 520 – 1710 kHz (USA version);
AM 522 – 1629 kHz (Europe version)
14
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement