2007 - 2008 - secure-idle

2007 - 2008 - secure-idle
CHEVROLET INSTALLATION INSTRUCTIONS
UPLANDER 2007 to 2008
PN: SI 340 TK 06
Secure-Idle, Inc.
210 W. Lincoln St.
Saybrook, IL 61770
Ph. 309.475.2286
Fax 309.475.2140
www.secure-idle.com
SECURE-IDLE is an ignition switch bypass device designed to provide
all the electrical functions that the OEM ignition switch normally provides.
For proper operation and long term performance, DO NOT deviate from
the wire connection instructions.
TESTING THE SECURE-IDLE TK UNIT
For each wire connection, remove approximately one half inch of
insulation from the OEM wire, but DO NOT cut through the wire.
Cutting the wires causes high resistance and a possible failure point.
Strip approximately one half inch of insulation from the end of the
SECURE-IDLE wires to be attached to the OEM wires. Wrap the
SECURE-IDLE wire around the bare area of the OEM wire and solder
the connection. Tape the connection thoroughly after it cools.
DO NOT use scotch lock type pinch through connectors. These
connectors cannot handle the higher amperages of the ignition circuits,
and will void the SECURE-IDLE warranty.
Use the wiring diagram to locate the correct wire and pin location
on the backside of this page.
Installation
1: With the shift lever in PARK
OPTION 1: Follow standard test procedure.
OPTION 2: For brake light deactivation. Follow standard procedures
to test unit. When the vehicle is under SECURE-IDLE control,
depressing the brake pedal will automatically shut down the vehicle.
Insert the key and turn to the run position, depress the brake pedal.
This will reset the unit and put the vehicle back under OEM ignition
control.
Testing the SECURE-IDLE Unit
1. With the shift lever in PARK start the vehicle. Push and release the
RED push button switch. This activates the SECURE-IDLE unit. You
will hear a single click when the button is pushed.
2. Turn the key to the OFF position. The vehicle will remain running.
Test all OEM electrical functions, ie: blower motor, power windows,
radio, etc.
3. Turn the key to the START position, the starter motor should not
crank.
1. Remove the lower dash panel under the steering column to access
the OEM ignition switch which is mounted on the steering column.
Mount the SECURE-IDLE unit near the ignition switch.
4. Pull the shift lever from PARK into DRIVE then back into PARK.
This resets the SECURE-IDLE unit. Turn the key to the OFF position.
2. Locate a good metal ground and connect the Black SECURE-IDLE
wire.
5. Start the vehicle; activate the SECURE-IDLE unit by pushing and
releasing the RED push button.
3. Locate the OEM ignition switch and wiring. Remove the insulation
from the BROWN wire, Pin 3, and attach the RED 18 Ga. SECUREIDLE wire according to the above instructions. This OEM wire will be
hot in RUN
6. Turn the key to the OFF position and remove the key. The vehicle
will remain running as it is now under SECURE-IDLE control, and the
steering wheel and the gear shift lever are locked.
4. Locate the PINK wire, Pin 7. Attach the WHITE 18 Ga. SECUREIDLE wire according to the instructions. This OEM wire will be hot in
ACC. and RUN.
5. Locate the YELLOW wire, Pin 5. Attach the YELLOW 18 Ga.
SECURE-IDLE wire according to the instructions. This OEM wire will
be hot in START and RUN.
7. Recheck all RUN and ACCESSORY electrical functions while the
vehicle is under SECURE-IDLE control.
8. With the brakes applied, insert the key and turn to the ON or RUN
position. Move the gear shift lever from PARK to DRIVE then back to
PARK. This resets the SECURE-IDLE unit and the vehicle is now
back under OEM ignition switch control.
9. Turn the key to the OFF position and the engine will stop.
6. Locate the WHITE/BLACK wire, Pin 6. Attach the GRAY FUSIBLE
LINK wire according to the instructions. Connect the RED 10 Ga. wire
to the FUSIBLE LINK by way of the quick disconnect connector. This
OEM wire will be HOT at all times.
7. Connect the BROWN SECURE-IDLE wire to either of the following
options:
1: To back up Lamps, LT GREEN wire at the passenger side kick
panel. (Do not use with flashing back up lights). This option is for
automatic reset.
2: To brake lights, WHITE (See #3 if brake light deactivation is
required but the vehicle has flashing brake lights) This option is used
for vehicle shutdown when the brake pedal is depressed
3: Use drawing 01-0083 For CMHL brake light activation if the vehicle
has flashing brake lights or the emergency flasher is used
10. Tie wrap all loose wires and replace the removed panels.
11. To disable the SECURE-IDLE unit, pull apart the quick disconnect.
It is located on the RED 10 Ga. wire coming out of the SECURE-IDLE
unit.
12. Instruct all drivers on the proper operating, reset procedures, and
the location of the quick disconnect of the SECURE-IDLE unit.
13. In the unlikely event that the engine will not turn off after the unit
has been reset, the driver should disable the unit by pulling apart the
quick disconnect.
14. If the engine stalls while under SECURE-IDLE control, the unit
must be reset before the engine can be restarted.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising