CyberPower | CPBC10400 | User guide | CyberPower CPBC10400

CyberPower CPBC10400
LED INDICATOR
USB BATTERY PACK
USER GUIDE
NO.
TROUBLE SHOOTING
CONDITION
LED INDICATION
1
Battery Life Indicator
2
Overload
Four LEDs represent 25%,
50%, 75% and 100% battery
life from left to right side.
All four LEDs are flash simultaneously.
3
Low Battery
The first LED is flashes rapidly.
Problem
USB Battery a.The power of device
is over specification.
Pack does
not power
b.The battery is out
the device
of power
C.The battery pack is
charging the device
and the power source
is charging the
battery pack
simultaneously.
Note:
1. The LED indicator will automatically switch off after 5 seconds from
pressing the button.
2. When the battery pack connects to the USB power, the LED indicator will
light indicating the charging status. Press the button for switching off the
indicator, and simply press again to switch on the LED indicator.
PACKAGE CONTENTS
Model: CPBC10400 Series
• USB Battery Pack (CPBC10400 Series)
• User Guide
INTRODUCTION
The USB Battery Pack (CPBC10400 Series) is a
rechargeable lithium-ion battery with the high capacity that
is designed for powering up to two mobile devices such as
phones, MP3 players, tablets, and handheld gaming
devices while away from other power sources.
FEATURES
- Compact and portable design
- Dual output
- Built in USB input power cable
- Built in micro USB output connector
- Battery life indicator
Battery Capacity: 10400mAh
Rated Input: DC 5V, 2A
Rated Output:
USB Output: 5V, 2.1A
Micro USB Output: 5V, 1A
Charging time: ~7 Hours by the 2A power
Dimension: 4.42x3.06x1.05 inch
Weight: 9.14 oz
Environment:
Storage: 14 to 122˚F (-10 to 50˚C)
Operation: 32 to 104˚F (0 to 40˚C)
The CPBC10400 Series is packaged in a protection mode
for shipping. Prior to use, connect the CPBC10400 Series
to a USB power source to set it to normal mode and the
suggested a full 10-hour charge.
TO CHARGE THE BATTERY PACK
6
5
3
1
4
2
NO.
1
2
3
4
5
6
ITEM
USB Input Cable
Micro USB Output Connector
Flash Light
USB Output Port
Power On/ LED Indicator Switch
Power Off
Flash Light On/ Off
LED Battery Life lndicator
DESCRIPTION
5V/ 2A USB input
5V/ 1A Micro USB output
White light
5V/ 2.1A USB output
Press the button
Press and hold 3 seconds
Press twice
As the “LED INDICATOR”
table showing
Power bank
does not
charge
Charge the USB Battery Pack by attaching the USB charging
connector to any powered USB port, including but not limited
to the USB wall charger, desktop computer, laptop or USB
powered hub. When charge the battery pack, the LED
indicator would light up automatically. Press the button to turn
off if it is not required.
Recharge the CPBC10400 Series every 3 months when not
use to ensure the best battery performance. The battery
capacity may decline after 300 times usage.
CHARGE THE
POWER PACK
Solution
Check the power specification
of the device before charging
with the CPBC10400 Series
Charge the battery pack via a
USB port.
The device can’t be charged
when the power source is
charging the battery pack.
The solution is to remove the
device from the battery pack.
a.Incorrect connection Re-attach the USB connector
between charger and to the USB port.
USB Battery Pack.
b.No power from the
source.
a.Check that power is provided
to the USB port.
b. The battery pack has a low
charge. Recharge the
power battery pack.
SPECIFICATIONS
IMPORTANT! PRIOR TO FIRST USE
PRODUCT VIEW:
Possible Cause
C.Short Circuit of
Reset the battery pack.
battery pack product
SAFETY PRECAUTION
Before using the USB Battery Pack, please read the following
warnings carefully. Use the product according to the
procedures described in this manual. Failure to follow these
safety precautions may result in fire, explosion, electrical
shock or other dangers.
1. Do not disassemble this product, or any of its parts. 2. Store between 14 to 122°F (-10 to 50°C).Operate between
32 to 104°F(0 to 40°C).
3. Do not immerse this product in water or other liquids, as
such use may result in fire or electrical shock. If water or
other liquids enter the battery interior, unplug the product
immediately from any attached power source or device. 4. Do not use this product with wet hands. Moisture in or on
this product may result in electrical shock.
5. Do not expose this product to direct flame or leave it in an
overheated condition, as the battery may explode.
6. Store this product in a cool and dry environment when not in use.
7. Do not puncture this product. Puncturing the battery may
cause the release of harmful substances.
8. It is normal for the USB Battery Pack to become warm
during charging.
9. Keep this product out of the reach of children. Ensure that
all users read these warnings and instructions before using.
10. Please recycle USB Battery Pack in accordance with local
environmental laws and regulations
radio frequency energy and if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However, there is no
guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful
interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or
more of the following measures:
• Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and
receiver.
– Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician
for help.
If the LED indicator extinguishes automatically during the
charging process, press the button to revert.
FCC WARNING
Changes or modifications not expressly approved by the
party responsible for compliance with the FCC Rules could
void the user’s authority to operate this equipment.
LIMITED PRODUCT WARRANTY
CyberPower offers limited product warranty for the hardware of
the USB Battery Pack* and the product is free from material
and manufacturing defects for one year. (*battery excluded) A
reasonable purchase proof with date must be provided when
submission. CyberPower's sole responsibility is to repair or
replace the product if a material or manufacturing defect results
in product failure during its normal use. The warranty is void if
the product is damaged due to abuse, alteration, misuse,
negligence, incorrect voltage supply, air/water pollution,
accidents and natural disasters.
LEGAL NOTICES
FCC Part 15
This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the
FCC rules. These limits are designed to provide reasonable
protection against harmful interference in a residential
installation. This equipment generates uses and can radiate
CyberPower Systems, Inc.
www.cpsww.com
© 2013 CyberPower Systems, Inc.
All rights reserved. Reproduction in whole or in part without permission is prohibited.
K09-0000171-00
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising