TWIST BIKE RACK - Forms+Surfaces
TWIST BIKE RACK
SURFACE MOUNT INSTALLATION INSTRUCTIONS
MATERIALS INCLUDED
a
b
c
STEP BY STEP
steel
wire brush
pencil
5/32" hex bit for tamperresistant screws
7/32" hex bit for tamperresistant screws
TOOLS NEEDED
1/4", 1/2" & 3/4" drill
bits for concrete
epoxy
hammer drill
epoxy gun
Loctite
FOR ALL TWIST BIKE RACKS
a
Mark hole locations
Drill holes
Fill holes & insert anchors
• Place bike rack in desired location ensuring
stabilization. Mark center of each hole
location with a pencil.
• Use hammer drill to drill 4.5" deep x 3/4"
diameter anchor hole at each marked
location using a 3/4" drill bit suitable for
concrete drilling.
• Use compressed air and steel wire brush
to clean each anchor hole in accordance
with epoxy instructions.
NOTE: Forms+Surfaces recommends
starting holes with 1/4" diameter drill
bit followed by 1/2" and finally 3/4" for
maximum accuracy.
• Use epoxy in epoxy gun to fill each anchor
hole 5/8 of the hole depth in accordance
with epoxy instructions.
• Insert 3/8"-16 x 4-1/4" epoxy anchor
(a) into each anchor hole so anchor top
is flush with ground. Allow proper curing
time according to cure schedule on epoxy
instructions before moving on to Step 4.
T 800.451.0410 | www.forms-surfaces.com
© 2015 Forms+Surfaces® | All dimensions are nominal. Specifications and pricing subject to change without notice. For the most current version of this document, please refer to our website at www.forms-surfaces.com.
page 1 of 4 | 06-18-15
TWIST BIKE RACK
SURFACE MOUNT INSTALLATION INSTRUCTIONS
STEP BY STEP
FOR ALL TWIST BIKE RACKS
b
Position bike rack
Attach bike rack and tighten screws
• Position bike rack so that mounting
holes line up with anchors.
• Insert four 3/8"-16 x 1-1/2" button head
cap screws (b) into mounting holes in
bike rack. Thread anchors using provided
7/32" hex bit for tamper-resistant
screws.
Slide cover plate over base of bike rack
• Tighten all screws.
NOTE: Forms+Surfaces recommends
applying Loctite® or similar threadlocking adhesive.
T 800.451.0410 | www.forms-surfaces.com
© 2015 Forms+Surfaces® | All dimensions are nominal. Specifications and pricing subject to change without notice. For the most current version of this document, please refer to our website at www.forms-surfaces.com.
page 2 of 4 | 06-18-15
TWIST BIKE RACK
SURFACE MOUNT INSTALLATION INSTRUCTIONS
STEP BY STEP
FOR ALL TWIST BIKE RACKS
7
c
Attach cover plate and tighten screws
• Thread 10-24 x 1" button head screws
(c) through each hole using provided
5/32" hex bit for tamper-resistant screws.
• Tighten all screws.
NOTE: Forms+Surfaces recommends
applying Loctite® or similar threadlocking adhesive.
T 800.451.0410 | www.forms-surfaces.com
© 2015 Forms+Surfaces® | All dimensions are nominal. Specifications and pricing subject to change without notice. For the most current version of this document, please refer to our website at www.forms-surfaces.com.
page 3 of 4 | 06-18-15
TWIST BIKE RACK
SURFACE MOUNT INSTALLATION INSTRUCTIONS
wall
wall
36" min
48" min
96" (72" min)
CORDIA BIKE RACK
60" (48" min)
36"
(24" min)
36" min
96" (72" min)
wall
wall
RECOMMENDED BICYCLE RACK SPACING PER ASSOCIATION OF PEDESTRIAN AND BICYCLE PROFESSIONALS (APBP) GUIDELINES FOR ALL TWIST BIKE RACKS
T 800.451.0410 | www.forms-surfaces.com
© 2015 Forms+Surfaces® | All dimensions are nominal. Specifications and pricing subject to change without notice. For the most current version of this document, please refer to our website at www.forms-surfaces.com.
page 4 of 4 | 06-18-15
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement