Samsung NK36K7000WS, NK36K7000WG User manual

Samsung NK36K7000WS, NK36K7000WG User manual
Range Hood
Hotte de la cuisine
Campana de cocina
Installation Instructions Guide
Guide d’instructions d’installation
Guía de Instrucciones para Instalación
NK30K7000WS / NK36K7000WS / NK30K7000WG / NK36K7000WG
LIB0124068
Table of Contents
Table of Contents
Important Safety Instructions
3
Installation Requirements
4
Electrical Requirements
Venting Requirements
Venting Methods
Tools and Parts
Dimensions and Clearances
4
4
4
5
5
Installation6
2
Prepare Location
Vent Cover Bracket Installation
Installing the Range Hood
Connect Vent System
Electrical Connection
Install Duct Covers
Complete Installation
6
6
6
7
7
8
8
Range Hood Use
8
Range Hood Controls
Range Hood Description
Conectivity Cooktop / Hood Range
9
8
9
Range Hood Care
10
Stainless Steel Baffle Filter
Cleaning
Replacing a LED Lamp
10
10
10
Warranty (USA)
11
Warranty (Canada)
12
English
Important Safety Instructions
APPROVED FOR RESIDENTIAL APPLIANCES
FOR RESIDENTIAL USE ONLY
READ AND SAVE THESE INSTRUCTIONS
PLEASE READ ENTIRE INSTALLATION GUIDE BEFORE PROCEEDING.
INSTALLATION MUST COMPLY WITH ALL LOCAL CODES.
Important Safety Instructions
IMPORTANT: Save these Instructions for the Local Electrical
Inspector’s use.
INSTALLER: Please leave these Instructions with this unit for
the owner.
OWNER: Please retain these instructions for future
reference.
Symbols used in this manual
WARNING
Hazards or unsafe practices that may result in severe personal injury or
death.
CAUTION
Hazards or unsafe practices that may result in electric shock, personal
injury, or property damage.
NOTE
Useful tips and instructions
These warning icons and symbols are here to prevent injury to you and
others.
Please follow them explicitly. After reading this section, keep it in a safe
place for future reference.
WARNING
Turn off power circuit at service panel and lock
out panel before wiring this appliance.
Requirement 120 VAC, 60 Hz. 15 or 20 A Branch Circuit
State of California Proposition 65 warning (US only)
WARNING
This product contains chemicals known to the State of California to cause
cancer and birth defects or other reproductive harm.
Gas appliances can cause low-level exposure to Proposition 65 listed
substances, including but not limited to, benzene, carbon monoxide,
formaldehyde and soot, substances resulting from the incomplete
combustion of natural gas or LP fuels.
1. FCC Notice
CAUTION
FCC CAUTION: Any changes or modifications not expressly approved
by the party responsible for compliance could void the user’s authority to
operate the equipment.
This device complies with Part 15 of FCC Rules. Operation is Subject to
following two conditions:
1) This device may not cause harmful interference, and
2) This device must accept any interference received including
interference that cause undesired operation.
For products sold in the US and Canadian markets, only channels 1~11
are available. You cannot select any other channels.
FCC STATEMENT:
This equipment has been tested and found to comply within the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation.
This equipment generates, uses, and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorienting or relocating the receiving antenna
• Increasing the separation between the equipment and receiver
• Connecting the equipment to an outlet that is on a different circuit than
the radio or TV
• Consulting the dealer or an experienced radio/TV technician for help.
FCC RADIATION EXPOSURE STATEMENT:
This equipment complies with FCC radiation exposure limits set forth for
an uncontrolled environment. This equipment should be installed and
operated so there is at least 8 inches (20 cm) between the radiator and
your body. This device and its antenna(s) must not be co-located or
operated in conjunction with any other antenna or transmitter.
2. IC Notice
The term “IC” before the radio certification number only signifies
that Industry Canada technical specifications were met. Operation is
subject to the following two conditions: (1) this device may not cause
interference, and (2) this device must accept any interference, including
interference that may cause undesired operation of the device.
This Class B digital apparatus complies with Canadian ICES-003. For
products sold in the US and Canadian markets, only channels 1~11 are
available. You cannot select any other channels.
IC RADIATION EXPOSURE STATEMENT:
This equipment complies with IC RSS-102 radiation exposure limits set
forth for an uncontrolled environment. This equipment should be installed
and operated so there is at least 8 inches (20 cm) between the radiator
and your body. This device and its antenna(s) must not be co-located or
operated in conjunction with any other antenna or
transmitter.
English
3
Important Safety Instructions
WARNING
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO
PERSONS, OBSERVE THE FOLLOWING PRECAUTIONS:
■■ Use this unit only in the manner intended by the manufacturer. If you
have questions, contact the manufacturer.
■■
Before servicing or cleaning the unit, switch the power off at the
service panel and lock the service panel to prevent power from being
switched on accidentally. If the service panel cannot be locked,
securely fasten a prominent warning device, such as a tag to the
service panel.
Important Safety Instructions
■■ Installation work and electrical wiring must be done by qualified
person(s) in accordance with all applicable codes and standards,
including fire-rated construction.
■■
Sufficient air is needed for proper combustion and exhausting of
gases through the flue (chimney) of fuel burning equipment to
prevent backdrafting. Follow the heating equipment manufacturer’s
guideline and safety standards such as those published by the
National Fire Protection Association (NFPA), the American Society
for Heating, Refrigeration and Air Conditioning Engineers (ASHRAE),
and the local code authorities.
■■ When cutting or drilling into the wall or ceiling; do not damage
electrical wiring and other hidden utilities.
■■ Ducted fans must always be vented outdoors.
CAUTION
For general ventilating use only. Do not use to exhaust hazardous or
explosive materials and vapors.
CAUTION
To reduce risk of fire and to properly exhaust air, be sure to duct air outside - do not vent exhaust air into spaces within walls or ceilings, attics or
into crawl spaces, or garages.
WARNING
TO REDUCE THE RISK OF FIRE, USE ONLY METAL DUCTWORK
WARNING
TO REDUCE THE RISK OF A RANGE TOP GREASE FIRE:
■■ Never leave surface units unattended at high settings. Boilovers
cause smoking and greasy spillovers that may ignite. Heat oils slowly
on low or medium settings.
■■ Always turn hood ON when cooking at high heat or when flambeing
food (i.e. Crepes Suzette, Cherries Jubilee, Peppercorn Beef Flambé).
■■ Clean ventilating fans frequently. Grease should not be allowed to
accumulate on the fan or filter.
■■ Use proper pan sizes. Always use cookware appropriate for the size
of the surface element.
WARNING
TO REDUCE THE RISK OF INJURY TO PERSONS IN THE EVENT OF
A RANGE TOP GREASE FIRE, OBSERVE THE FOLLOWING
PRECAUTIONS:a
■■ SMOTHER FLAMES with a close fitting lid, cookie sheet, or metal
tray, then turn off the burner. BE CAREFUL TO PREVENT BURNS.
If the flames do not go out immediately, EVACUATE AND CALL THE
FIRE DEPARTMENT.
■■ NEVER PICK UP A FLAMING PAN - you may get burned.
■■ DO NOT USE WATER, including wet dishcloths or towels a violent steam explosion will result.
■■ Use an extinguisher ONLY if:
-You know you have a class ABC extinguisher, and you already know
how to operate it.
– The fire is small and contained in the area where it started.
– The fire department is being called.
– You can fight the fire with your back to an exit.
a
Based on “Kitchen Fire Safety Tips” published by NFPA.
WARNING
To reduce the risk of fire or electrical shock, do not use this fan with any
solid-state speed control device.
This hood is suitable only for mounting over gas ranges with a maximum
power of 59,000 BTU’s only.
WARNING
Do not let children near this appliance. Do not let children play with this
appliance.
Keep all packaging materials out of children’s reach. Properly dispose the
packaging materials after this appliance is unpacked.
Read and save these Instructions
4
English
Installation Requirements
For the most efficient and quiet operation:
IMPORTANT
Observe all governing codes and ordinances.
••
Use no more than three 90° elbows.
••
Make sure there is a minimum of 24” (61 cm) of straight vent
between the elbows if more than 1 elbow is used.
••
Do not install 2 elbows together.
••
Use clamps to seal all joints in the vent system.
••
The vent system must have a damper. If the roof or wall cap
has a damper, do not use the damper supplied with the range
hood.
••
Use caulking to seal the exterior wall or roof opening around the cap.
••
The size of the vent should be uniform.
It is the customer’s responsibility:
To contact a qualified electrical installer.
To assure that the electrical installation is adequate and in
conformance with National Electrical Code, ANSI/NFPA 70
— latest edition*, or CSA Standards C22.1-94, Canadian
Electrical Code, Part 1 and C22.2 No.0-M91 - latest edition** and all local
codes and ordinances.
If codes permit and a separate ground wire is used, it is recommended
that a qualified electrician determine that the ground path is adequate.
A copy of the above code standards can be obtained from:
National Fire Protection Association
1 Batterymarch Park
Quincy, MA 02169-7471
CSA International
8501 East Pleasant Valley Road
Cleveland, OH 44131-5575
■■ A 120 volt, 60 Hz., AC only, 15-amp, fused electrical circuit is
required.
■■ If the house has aluminum wiring, follow the procedure below:
1. Connect a section of solid copper wire to the pigtail leads.
2. Connect the aluminum wiring to the added section of
copper wire using special connectors and/or tools designed
and UL listed for joining copper to aluminum.
■■ Follow the electrical connector manufacturer’s recommended
procedure. Aluminum/copper connection must conform with local
codes and industry accepted wiring practices.
■■
Wire sizes and connections must conform with the rating of
the appliance as specified on the model/serial rating plate.
The model/serial plate is located behind the filter on the rear
wall of the range hood.
■■
Wire sizes must conform to the requirements of the National
Electrical Code, ANSI/NFPA 70 (latest edition), or CSA
Standards C22. 1-94, Canadian Electrical Code, Part 1 and
C22.2 No. 0-M91 (latest edition and all local codes and
ordinances.
Installation Requirements
Electrical Requirements
Venting Methods
This canopy hood is factory set for venting through the roof or
wall. A 6” (15.2 cm) round vent system is needed for installation (not
included). The hood exhaust opening is 6” (15.2 cm) round.
NOTE
Flexible vent is not recommended. Flexible vent creates back pressure
and air turbulence that greatly reduce performance. Vent system can
terminate either through the roof or wall. To vent through a wall, a 90°
elbow is needed.
Mounting Height
Select a mounting height between a minimum of 24” (76.2 cm) for an
electric cooking surface, a minimum of 30” (76.2 cm) for a gas cooking
surface, and a suggested maximum of 36” (91.4 cm) above the range to
the bottom of the hood.
Rear discharge
A 90° elbow may be installed immediately above the hood.
Roof Venting
Wall Venting
A
B
B
A
Venting Requirements
(ducted models only)
••
Vent system must terminate to the outdoors, except for non
vented (recirculating) installations.
••
Do not terminate the vent system in an attic or other enclosed area.
••
Do not use 4” (10.2 cm) laundry-type wall cap.
••
Use metal vent only. Rigid metal vent is recommended.
Plastic or metal foil vent is not recommended.
••
The length of the vent system and number of elbows should
be kept to a minimum to provide efficient performance.
A. Roof cap
B. 6” (15.2 cm) round vent
A.Wall cap
B. 6” (15.2 cm) round vent
English
5
Installation Requirements
Tools and Parts
Dimensions and Clearances
E
Parts supplied
Removing the packaging
CAUTION!
Remove carton carefully, wear gloves to protect against sharp edges.
G
F
Installation Requirements
WARNING
Remove the protective film covering the product before putting into
operation.
•• Hood canopy assembly with blower and LED lamps already installed.
C
••
6” (15.2 cm) round air transition
D
••
Duct covers
••
Hardware bag with:
Part
5x45 mm
Qty
Part
Qty
6
5.4x75 mm screws
(for 10x60 mm wall
anchors)
4
2
8x40 mm
3.5x9.5 mm
4x8 mm
2
Torx 10 adapter
Duct cover bracket
4
H
A
1
1
A
1
Mounting template
Tools/Materials required
••
Level
••
Drill with 1¼” (3.2 cm),1⁄8” (3.2 mm), and 1⁄16” (4,8 mm) drill bits
••
Pencil
••
Wire stripper or utility knife
••
Tape measure or ruler
••
Pliers
••
Caulking gun and weatherproof caulking compound
••
Vent clamps
••
Jigsaw or keyhole saw
••
Flat-blade screwdriver
••
Metal snips
••
Phillips & Torx 20 screwdriver
••
Home power supply cable
••
½” (12.7 mm) UL listed or CSA approved strain relief
••
3 UL listed wire connectors
For vented installations, you will also need:
6
••
1 wall or roof cap
••
Metal vent system
English
NK30K7000WS
NK30K7000WG
NK36K7000WS
NK36K7000WG
30”
(76 cm)
36”
(91.2 cm)
B
1911⁄16” (50 cm)
C*
max. 4311⁄32” (110.1 cm)
min. 291⁄16” (73.8 cm)
D**
max. 3931⁄64” (100.3 cm)
min. 2525⁄64” (64.5 cm)
E
6” (15.24 cm)
F
1019⁄32” (26.9 cm)
G
135⁄64” (33.2 cm)
H
223⁄64” (6 cm)
4
10 x 60 mm
Parts needed
B
*For non-vented (recirculating installations)
**For vented installations
Installation
Installation Instructions
Vent cover bracket installation
1. Attach the vent cover bracket to the wall flush to the ceiling using
2 - 5 x 45 mm screws.
Prepare Location
••
It is recommended that the vent system be installed before the hood
is installed.
••
Before making cutouts, make sure there is proper clearance within
the ceiling or wall for the exhaust vent.
••
Check your ceiling height and the hood height maximum before you
select your hood.
A
D
B
1. Disconnect power.
A. 8 x 40 mm drywall anchors
B. Centerline on wall
C. Vent cover support bracket
D. 5 x 45 mm screws
2. Determine which venting method to use: roof, wall, or nonvented.
WARNING
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO
PERSONS, OBSERVE THE FOLLOWING
4. Using 2 or more people, lift the range hood onto covered surface.
Range hood mountig screws installation
1. Determine and mark the centerline on the wall where the
canopy hood will be installed. Disconnect power.
2.
Select a mounting height between a minimum of 24” (60.9 cm)
for an electric cooking surface, a minimum of 30” (76.2
cm) for a gas cooking surface, and a suggested maximum of
36” (91.4 cm) above the range to the bottom of the hood.
Mark a reference line on the wall.
3. Tape the template in place, aligning the template centerline and the
bottom of the template with the hood bottom line and with the
centerline marked on the wall.
Complete Preparation
1. Determine and make all necessary cuts in the wall for the
vent system. Install the vent system before installing the hood. See the “Venting Requirements” section.
Installation
3. Select a flat surface for assembling the range hood.
Place a covering over that surface.
C
2. Determine the required height for the home power supply
cable and drill a 1¼” (3.2 cm) hole at this location.
3.
Run the home power supply cable according to the National
Electrical Code or CSA Standards and local codes and
ordinances. There must be enough ½” conduit and wires from
the fused disconnect (or circuit breaker) box to make the
connection in the hood’s electrical terminal box.
NOTE
Do not reconnect power until installation is complete.
4. Use caulk to seal all openings.
Installing the range hood
1. Using 2 or more people, hang the range hood on 2 mounting
screws through the mounting slots on the back of the hood.
A
A
B
B
C
A. Centerline
B. Fastener locations
C. Mounting height reference (hood bottom line)
5. Mark the fastener locations by pushing a pen or pencil tip through the
template into the wall.
IMPORTANT: All screws must be installed into wood. If there is no wood
to screw into, additional wall framing supports may be required.
C
6. Remove the template.
7. Drill ⁄16” (4.8 mm) pilot holes at all locations where screws are
being installed into wood.
3
8. Install the 2 - 5 x 45 mm mounting screws. Leave a 1⁄4”(6.4 mm) gap
between the wall and the back of the screw head to slide the range
hood into place.
1⁄4”
(6.4 mm)
A. Mounting screws
B. Mounting slots
C. Lower mounting screws
2. Mark with a pencil the lower mounting hole’s location.
3. Uninstall the hood assembly, and then drill 3⁄16” (4.8 mm) pilot
holes at the marked locations.
4. Hang the range hood again on the 2 upper mounting screws.
5. Level the range hood and tighten the upper mounting screws.
6. Install the 2 - 5 x 45 mm lower mounting screws and tighten.
Use the optional wall anchors if needed.
English
7
Installation
Connecting Vent System
1. Install the transition on the top of the hood (if removed for shipping)
with 2 - 3.5 x 9.5 mm sheet metal screws.
B
C
A
A
B
Installation
A. Terminal box
B. Knockout
C. Terminal box cover
4. Run the home power supply cable through strain relief, into
terminal box.
A. Vent transition
B. 3.5 x 9.5 mm screw
A
B
For vented installations only:
2. Fit the vent system over the exhaust outlet.
E
3. Measure from the bottom of the air deflector to the bottom of the hood outlet. Cut the ductwork at the measured lenght.
Roof
outlet
D
Wall
outlet
Dimension
to measure
C
F
4. Seal the connection with clamps.
5. Check that the back draft dampers work properly.
Electrical Connection
WARNING
Electrical Shock Hazard
Disconnect power before servicing.
Replace all parts and panels before operating.
Failure to do so can result in death or electrical shock.
1. Disconnect power.
2. Remove the terminal box cover.
3. Remove the knockout in the terminal box cover and install
a UL listed or CSA approved 1⁄2” strain relief.
A. Home power supply cable
B. UL listed or CSA approved
strain relief
C. Black wires
5. Use UL listed wire connectors and connect the black wires
(C) together.
6. Use UL listed wire connectors and connect the white wires (E)
together.
WARNING
Electrical Shock Hazard
Electrically ground blower.
Connect the ground wire to the green and yellow ground wire in the
terminal box. Failure to do so can result in death or electrical shock.
7. Connect the green (or bare) ground wire from the home power
supply to the yellow-green ground wire (F) in terminal box using
UL listed wire connectors.
8. Tighten the strain relief screw.
9. Install the terminal box cover.
10. Reconnect power.
8
English
D. UL listed wire connectors
E. White wires
F. Green (or bare) and
yellow-green ground wires
Installation
Installing the duct covers
Secure the bottom of the duct with 2 - 4.2 x 8 mm screws.
When using both upper and lower vent covers, push the lower cover
down onto hood and lift the upper cover to the ceiling and install with two
mounting screws.
NOTE
For vented installations, the upper vent cover may be reversed to hide the
slots.
C
D
C
A
Installation
Completing the Installation
B
1. Install the metal baffle filters. See the “Range Hood Care” section.
2. Check the operation of the range hood blower and light.
See the “Range Hood Use” section.
NOTE
To get the most efficient use from your new range hood, read the “Range
Hood Use” section.
A. Upper vent cover
B. Lower vent cover
C. 4.2 x 8 mm screws
D. Bracket
Range Hood Use
Range Hood Description
The range hood is designed to remove smoke, cooking vapors and odors from the cooktop area. For best results, start the hood before cooking and
allow it to operate several minutes after cooking is complete to clear all smoke and odors from the kitchen. The hood controls are located on the front
side.
C
D
A
B
A. Baffle filter
B. Baffle filter handle
C. Blower and light controls
D. LED lamps
English
9
Range Hood Use
Range Hood Controls
A
B
C
D
E
F
G
I
A. Power
B. Low Speed
C. Medium Speed
D. High Speed
E. Boost Speed
F. Timer Display
G. Timer
H. Light
I. Auto
Connectivity
J. Bluetooth
CONNECTIVITY COOKTOP / HOOD RANGE
••
This appliance has a feature which allows you to pair compatible Samsung cooktops and your hood via Bluetooth.
••
Press the POWER button and the hood will be activated at default speed (Default Speed : Low).
Press the LOW button and the hood will be activated at Low speed.
MED
•• Press the MED button and the hood will be activated at Medium
speed.
HIGH
•• Press the HIGH button and the hood will be activated at High speed.
BOOST
••
Press the BOOST button and the hood will be activated at Maximum
speed for 10 minutes.
••
After 10 minutes, the hood will slow to High speed.
Timer Display
••
Shows the timer settings.
Timer
Set the timer ON
••
Press the Timer button to set the working time.
••
Each time you press the Timer, you add 10 minutes to the
displayed time, up to a maximum of 99 minutes. The hood will
stay on for the amount of time you have set.
After setting time, the timer LED light will start to blink.
••
After the Timer counts down to zero, the Timer LED light will
start to blink.
••
The Timer LED will blink for 5 seconds, and then the hood will
turn off automatically.
Set the timer OFF
••
Press the Timer button for 3 seconds and the Timer function will be
deactivated.
After you enable this function and pair your hood and a compatible cooktop, the hood fan will automatically come on at Low speed when you turn
on a cooktop element. The hood fan will also shut off automatically when
you turn off the cooktop elements.
In addition, after the hood and compatible cooktop are paired, you can
download the Samsung Smart Home app to a mobile device, and then
use the Samsung Smart Home app to:
•• Monitor and control the On/Off status of the hood.
••
Monitor and control the fan speed.
••
Monitor and control the lights.
••
Set th hood shut-off timer with the time-up alarm.
For more information about downloading the Samsung Smart Home app
to your mobile device and using to control your hood, visit www.samsung.
com.
Auto Connectivity
The Auto Connectivity function lets you quickly connect the hood via
Bluetooth with a compatible Samsung cooktop after the hood and cooktop have been paired. To turn the function on, press the Auto Connectivity
button. To turn the function off and disconnect the hood and cooktop,
press the Auto Connectivity button again.
While the hood and cooktop are connected, the hood fan will automatically come on at Low speed when you turn on a cooktop element. The
hood fan will also shut off automatically when you turn off the cooktop
elements. You will also be able to control the hood with the Samsung
Smart Home app as described above.
1. Press the Auto Connectivity button to activate the function.
2. The hood will turn on/off automatically following the cooktop.
3. Press again to deactivate the function.
Image
Light
Remote Control
by Samsung
Smart Home App
Auto
Connectivity
Hood
Function
••
Press the Light button and the lamps will turn on.
X
X
O
••
Press the Light button again and the lamps will turn off.
O
X
O
O
O
O
Bluetooth connection (Pairing)
1. Press the Bluetooth button on hood. The pairing mode will be
activated and the indicator on the Bluetooth button will blink.
2. Press the Bluetooth button on cooktop.
NOTE
Detailed pairing mehtod with the cooktop, please refer to User manual of
the Cooktop.
3. After the pairing proccess finishes, the Bluetooth light will stay lit
and
word appears on the display.
Bluetooth disconnection (Pairing reset)
1. Press and hold 3 seconds the Bluetooth button on hood.
2. The Bluetooth connection will be disconnected.
10
J
POWER
•• Press again and the hood will return to sleep mode.
LOW
Range Hood Use
H
English
NOTE
Only the Bluetooth available cooktop of Samsung can activate this function.
Range Hood Care
Range Hood Care
2. Wash the stainless steel baffle filter as needed in your dishwasher
or a hot detergent solution.
Cleaning
3. Reinstall the filter by making sure the spring release
handles are toward the front. Insert the stainless steel filter into the
upper track.
IMPORTANT: Clean the hood and baffle filters frequently according to the
following instructions. Replace the baffle filters before operating the hood.
Exterior Surfaces:
To avoid damage to the exterior surface, do not use steel wool or soapfilled scouring pads to clean the hood.
Always wipe dry to avoid water marks.
••
Wipe with a damp soft cloth or nonabrasive sponge, then rinse
with clean water and wipe dry.
••
Do not use cleaning agents containing bleach.
5. Push up on the stainless steel filter, and then release the handle to
latch the filter into place.
WARNING
When removing the filter, please hold it with both hands to make sure it
does not fall.
Replacing an LED Lamp
The LED lights are replaceable by a service technician only. See support
contacts in the Warranty section.
Range Hood Care
Cleaning Method:
•• Liquid detergent soap and water or all-purpose cleanser
4. Push in the spring release handle.
Stainless Steel Baffle Filter:
1. Remove the filter by pulling the spring release handle, and
then pulling down the filter.
A
A. Spring release handle
English
11
warranty (USA)
SAMSUNG RANGE HOOD
Limited warranty to original purchaser
This SAMSUNG brand product, as supplied and distributed by
Samsung Electronics America, Inc. (SAMSUNG) and delivered
new, in the original carton to the original consumer purchaser, is
warranted by SAMSUNG against manufacturing defects in materials and workmanship for a limited warranty period of:
ONE (1) YEAR PARTS AND LABOR
This limited warranty begins on the original date of purchase,
and is valid only on products purchased and used in the United
States. To receive warranty service, the purchaser must contact
SAMSUNG for problem determination and service procedures.
Warranty service can only be performed by a SAMSUNG authorized service center. The original dated bill of sale must be
presented upon request as proof of purchase to SAMSUNG or
SAMSUNG’s authorized service center.
SAMSUNG will repair or replace this product, at our option and
at no charge as stipulated herein, with new or reconditioned
parts or products if found to be defective during the limited
warranty period specified above. All replaced parts and products become the property of SAMSUNG and must be returned
to SAMSUNG. Replacement parts and products assume the
remaining original warranty, or ninety (90) days, whichever is
longer.
In-home service will be provided during the warranty labor
period subject to availability within the contiguous United States.
In-home service is not available in all areas. To receive in-home
service, the product must be unobstructed and accessible to
service personnel. If during in-home service repair can not be
completed, it may be necessary to remove, repair and return the
product.
This limited warranty covers manufacturing defects in materials
and workmanship encountered in normal, noncommercial use of
this product and shall not apply to the following, including, but
not limited to: damage which occurs in shipment; delivery and
installation; applications and uses for which this product was not
intended; altered product or serial numbers; cosmetic damage
or exterior finish; accidents, abuse, neglect, fire, water, lightning
or other acts of nature; use of products, equipment, systems,
utilities, services, parts, supplies, accessories, applications,
installations, repairs, external wiring or connectors not supplied
or authorized by SAMSUNG which damage this product or result
in service problems; incorrect electrical line voltage, fluctuations
and surges; customer adjustments and failure to follow operating instructions, cleaning, maintenance and environmental
instructions that are covered and prescribed in the instruction
book; problems caused by pest infestations, and overheating or
overcooking by user; glass tray or turntable; reduced magnetron
power output related to normal aging. SAMSUNG does not warrant uninterrupted or error-free operation of the product.
THERE ARE NO EXPRESS WARRANTIES OTHER THAN THOSE
LISTED AND DESCRIBED ABOVE, AND NO WARRANTIES
WHETHER EXPRESS OR IMPLIED, INCLUDING, BUT NOT
LIMITED TO, ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, SHALL
APPLY AFTER THE EXPRESS WARRANTY PERIODS STATED
ABOVE, AND NO OTHER EXPRESS WARRANTY OR GUARANTY GIVEN BY ANY PERSON, FIRM OR CORPORATION
WITH RESPECT TO THIS PRODUCT SHALL BE BINDING ON
SAMSUNG. SAMSUNG SHALL NOT BE LIABLE FOR LOSS OF
REVENUE OR PROFITS, FAILURE TO REALIZE SAVINGS OR
OTHER BENEFITS, OR ANY OTHER SPECIAL, INCIDENTAL OR
CONSEQUENTIAL DAMAGES CAUSED BY THE USE, MISUSE
OR INABILITY TO USE THIS PRODUCT, REGARDLESS OF
THE LEGAL THEORY ON WHICH THE CLAIM IS BASED, AND
EVEN IF SAMSUNG HAS BEEN ADVISED OF THE POSSIBILITY
OF SUCH DAMAGES. NOR SHALL RECOVERY OF ANY KIND
AGAINST SAMSUNG BE GREATER IN AMOUNT THAN THE
PURCHASE PRICE OF THE PRODUCT SOLD BY SAMSUNG
AND CAUSING THE ALLEGED DAMAGE. WITHOUT LIMITING
THE FOREGOING, PURCHASER ASSUMES ALL RISK AND
LIABILITY FOR LOSS, DAMAGE OR INJURY TO PURCHASER
AND PURCHASER’S PROPERTY AND TO OTHERS AND THEIR
PROPERTY ARISING OUT OF THE USE, MISUSE OR INABILITY
TO USE THIS PRODUCT SOLD BY SAMSUNG NOT CAUSED
DIRECTLY BY THE NEGLIGENCE OF SAMSUNG. THIS LIMITED
WARRANTY SHALL NOT EXTEND TO ANYONE OTHER THAN
THE ORIGINAL PURCHASER OF THIS PRODUCT IS NONTRANSFERABLE AND STATES YOUR EXCLUSIVE REMEDY.
Some provinces or territories may or may not allow limitations on
how long an implied warranty lasts, or the exclusion or limitation
of incidental or consequential damages, so the above limitations
or exclusions may not apply to you. This warranty gives you
specific legal rights, and you may also have other rights which
vary from state to state.
To obtain warranty service, please contact SAMSUNG at:
1-800-SAMSUNG (726-7864) or
www.samsung.com/us/support
warranty (Canada)
SAMSUNG RANGE HOOD
Limited warranty to original purchaser
This SAMSUNG brand product, as supplied and distributed by
Samsung Electronics America, Inc. (SAMSUNG) and delivered
new, in the original carton to the original consumer purchaser, is
warranted by SAMSUNG against manufacturing defects in materials and workmanship for a limited warranty period of:
ONE (1) YEAR PARTS AND LABOR
This limited warranty begins on the original date of purchase,
and is valid only on products purchased and used in the United
States. To receive warranty service, the purchaser must contact
SAMSUNG for problem determination and service procedures.
Warranty service can only be performed by a SAMSUNG authorized service center. The original dated bill of sale must be
presented upon request as proof of purchase to SAMSUNG or
SAMSUNG’s authorized service center.
SAMSUNG will repair or replace this product, at our option and
at no charge as stipulated herein, with new or reconditioned
parts or products if found to be defective during the limited
warranty period specified above. All replaced parts and products become the property of SAMSUNG and must be returned
to SAMSUNG. Replacement parts and products assume the
remaining original warranty, or ninety (90) days, whichever is
longer.
In-home service will be provided during the warranty labor
period subject to availability within the contiguous United States.
In-home service is not available in all areas. To receive in-home
service, the product must be unobstructed and accessible to
service personnel. If during in-home service repair can not be
completed, it may be necessary to remove, repair and return the
product.
This limited warranty covers manufacturing defects in materials
and workmanship encountered in normal, noncommercial use of
this product and shall not apply to the following, including, but
not limited to: damage which occurs in shipment; delivery and
installation; applications and uses for which this product was not
intended; altered product or serial numbers; cosmetic damage
or exterior finish; accidents, abuse, neglect, fire, water, lightning
or other acts of nature; use of products, equipment, systems,
utilities, services, parts, supplies, accessories, applications,
installations, repairs, external wiring or connectors not supplied
or authorized by SAMSUNG which damage this product or result
in service problems; incorrect electrical line voltage, fluctuations
and surges; customer adjustments and failure to follow operating instructions, cleaning, maintenance and environmental
instructions that are covered and prescribed in the instruction
book; problems caused by pest infestations, and overheating or
overcooking by user; glass tray or turntable; reduced magnetron
power output related to normal aging. SAMSUNG does not warrant uninterrupted or error-free operation of the product.
THERE ARE NO EXPRESS WARRANTIES OTHER THAN THOSE
LISTED AND DESCRIBED ABOVE, AND NO WARRANTIES
WHETHER EXPRESS OR IMPLIED, INCLUDING, BUT NOT
LIMITED TO, ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, SHALL
APPLY AFTER THE EXPRESS WARRANTY PERIODS STATED
ABOVE, AND NO OTHER EXPRESS WARRANTY OR GUARANTY GIVEN BY ANY PERSON, FIRM OR CORPORATION
WITH RESPECT TO THIS PRODUCT SHALL BE BINDING ON
SAMSUNG. SAMSUNG SHALL NOT BE LIABLE FOR LOSS OF
REVENUE OR PROFITS, FAILURE TO REALIZE SAVINGS OR
OTHER BENEFITS, OR ANY OTHER SPECIAL, INCIDENTAL OR
CONSEQUENTIAL DAMAGES CAUSED BY THE USE, MISUSE
OR INABILITY TO USE THIS PRODUCT, REGARDLESS OF
THE LEGAL THEORY ON WHICH THE CLAIM IS BASED, AND
EVEN IF SAMSUNG HAS BEEN ADVISED OF THE POSSIBILITY
OF SUCH DAMAGES. NOR SHALL RECOVERY OF ANY KIND
AGAINST SAMSUNG BE GREATER IN AMOUNT THAN THE
PURCHASE PRICE OF THE PRODUCT SOLD BY SAMSUNG
AND CAUSING THE ALLEGED DAMAGE. WITHOUT LIMITING
THE FOREGOING, PURCHASER ASSUMES ALL RISK AND
LIABILITY FOR LOSS, DAMAGE OR INJURY TO PURCHASER
AND PURCHASER’S PROPERTY AND TO OTHERS AND THEIR
PROPERTY ARISING OUT OF THE USE, MISUSE OR INABILITY
TO USE THIS PRODUCT SOLD BY SAMSUNG NOT CAUSED
DIRECTLY BY THE NEGLIGENCE OF SAMSUNG. THIS LIMITED
WARRANTY SHALL NOT EXTEND TO ANYONE OTHER THAN
THE ORIGINAL PURCHASER OF THIS PRODUCT IS NONTRANSFERABLE AND STATES YOUR EXCLUSIVE REMEDY.
Some provinces or territories may or may not allow limitations on
how long an implied warranty lasts, or the exclusion or limitation
of incidental or consequential damages, so the above limitations
or exclusions may not apply to you. This warranty gives you
specific legal rights, and you may also have other rights which
vary from state to state.
To obtain warranty service, please contact SAMSUNG at:
1-800-SAMSUNG (726-7864) or
www. samsung.com/ca/support (English),
www.samsung.com/ca_fr/support (French)
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement