IronStrike Installation and Operation Manual

Add to my manuals
46 Pages

advertisement

IronStrike Installation and Operation Manual | Manualzz
INSTALLATION AND OPERATION
Direct-Vent
Serefina™ Series
P/N 900129-00 REV. A 01/2015
A French manual is available upon request. Order
P/N 900186-00.
Ce manuel d’installation est disponible en
francais, s implement en faire la demande.
Numéro de la pièce 900186-00.
C
P900129-00
US
Report # 14-162
MODELS
CI1500DVF
CI2500DVF
This appliance may be installed in an aftermarket permanently located, manufactured home (USA only) or mobile
home, where not prohibited by local codes. This appliance is only for use with the type of gas indicated on the rating
plate. This appliance is not convertible for use with other gases, unless a certified kit is used.
Cet appareil peut installé dans une maison préfabriquée (mobile) déjà installée à demeure, si les réglements locaux
le permettent. Ce appareil doit être utilisé uniquement avec le type de gaz indiqué sure la plaque signalétique. Cet
appareil ne peut être converti à d'autres gaz, sauf si une trousse de conversion est utilsée.
WARNING:
FIRE OR EXPLOSION HAZARD
Failure to follow safety warnings exactly could result
in serious injury, death, or property damage.
— Do not store or use gasoline or other flammable vapors
and liquids in the vicinity of this or any other appliance.
— WHAT TO DO IF YOU SMELL GAS
• Do not try to light any appliance.
• Do not touch any electrical switch; do not use any
phone in your building.
• Leave the building immediately.
• Immediately call your gas supplier from a neighbor’s
phone. Follow the gas supplier’s instructions.
• If you cannot reach your gas supplier, call the fire
department.
— Installation and service must be performed by a qualified installer, service agency or the gas supplier.
INSTALLER: Leave this manual with the appliance.
CONSUMER: Retain this manual for future reference.
INstallateur: Laissez cette notice avec l'appareil.
Consommateur: Conservez cette notice pour consultation ultérieure.
AVERTISSEMENT:
RISQUED’INDENDIE OU D’EXPLOSION
Le non-respect Des avertissements de sécurité pourrait d’entraîner des blessures graves, la mort ou des
dommages matériels.
— Ne pas entreposer ni utilizer d’essence ni d’autres
vapeurs ou liquides inflammables dans le voisinage
de cet appareil ou de tout autre appareil.
— QUE FAIRE SI VOUS SENTEZ UNE ODEUR DE GAZ:
• Ne pas tenter d’allumer d’appareil.
• Ne touchez à aucan interrupteur. Ne pas vous servir
des téléphones se trouvant dans le bâtiment où vous
trouvez.
• Sortez immédiatement de bâtiment.
• Appelez immédiatement votre fournisseur de gaz
depuis un voisin. Suivez les instructions du fournisseur.
• Si vous ne pouvez rejoindre le fournisseur de gaz,
appelez le service des incindies.
— L’installation et l’entretien doivent être assurés par
un installateur ou un service d’entretien qualifié ou
par le fournisseur de gaz.
Safety and Your GAS STOVE
See attached color flyer for proper color representation
DANGER
HOT GLASS WILL
CAUSE BURNS.
DO NOT TOUCH GLASS
UNTIL COOLED.
NEVER ALLOW CHILDREN
TO TOUCH GLASS.
A barrier designed to reduce the risk of burns from the hot viewing glass is provided with this appliance and shall be installed for the protection of children and
other at-risk individuals.
Voir ci-joint tract pour une bonne représentation de la couleur
DANGER
VITRE CHAUDE
RISQUE DE BRÛLURES.
NE TOUCHEZ PAS UNE VITRE
NON REFROIDIE.
NE LAISSEZ JAMAIS UN ENFANT
DE TOUCHER LA VITRE.
L'écran pare-étincelles fourni avec ce foyer réduit le risque de brûlure en cas de
contact accidentel avec la vitre chaude et doit être installé pour la protection Des
enfants et Des personnes à risques.
Vea el volante adjunto para la representación de color adecuado
PELIGRO
2
EL VIDRIO CALIENTE
CAUSARÁ QUEMADURAS.
USTED DEBE NUNCA
TOCAR EL VIDRIO CALIENTE.
LOS NIÑOS DEBEN NUNCA
TOCAR EL VIDRIO.
Una barrera diseñada para reducir el riesgo de quemaduras desde la mirilla (vidrio)
caliente es proveida con este aparato y deberá instalarse para la protección de los
niños y otros individuos en riesgo.
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
Safety and Your La sécurité et votre Seguridad y su
poêles au gaz
Gas Stove
chimenea
All parts of your
IHP gas stove get
EXTREMELY HOT!
 To prevent severe burns
and injuries, do Not
remove the barrier on
the stove front which
prevents direct contact
with the glass.
 Follow the safety instructions below
and be sure everyone in your household
understands this burn hazard:
• The surfaces on your fireplace get
EXTREMELY HOT!
• The glass on the front of the
fireplace reaches EXTREMELY HIGH
temperatures and can cause severe
burns if touched.
• Keep children away from an operating
fireplace. Closely supervise children
in any room where a fireplace is
operating to prevent contact with glass.
• Keep clothing, furniture, gasoline, and
other flammable liquids away from the
fireplace.
• Even after the gas is turned off,
fireplace surfaces remain extremely
hot.
 Be sure to attach the enclosed Safetyin-Operation Warnings where you
turn on your fireplace, to help remind
everyone of the dangers associated with
high temperatures (see pages 6-7).
 Read Important Safety Information on
page 5.
[ENGLISH]
Toutes les parties de
votre poêles au gaz IHP
deviennent EXTRÊMEMENT
CHAUDES !
¡Todas las partes de la
chimenea IHP se ponen
MUY CALIENTES!
 Afin d’éviter les brûlures
graves ou les blessures,
ne pas retirer l’écran ou
la protection qui empêche
tout contact direct avec la
vitre.
 Suivez les instructions de sécurité
ci-dessous et veillez à ce que tous
les membres de votre famille soient
conscients du danger de brûlure
encouru :
 Para evitar quemaduras y lesiones
graves, no quite el protector de malla
o guardia de seguridad que evita el
contacto directo con el vidrio.
• Les surfaces de votre foyer deviennent
EXTRÊMEMENT CHAUDES !
• La vitre située à l'avant du foyer atteint
des températures EXTRÊMEMENT
ÉLEVÉES et peut causer de graves
blessures en cas de contact.
• Tenez les enfants à l'écart du foyer
lorsqu'il fonctionne. Surveillez
attentivement les enfants dans les
pièces où un foyer est utilisé afin
d'éviter qu'ils ne soient en contact avec
la vitre.
• Tenez tous les vêtements, les meubles,
l'essence et tout autre liquide
inflammable à l'écart du foyer.
• Même après fermeture du gaz, les
surfaces du foyer restent extrêmement
chaudes.
 Veillez à coller les Étiquettes de mise
en garde relatives à la sécurité
d'utilisation à l'endroit où vous
utilisez le foyer, pour rappeler à tous
les utilisateurs les dangers liés aux
températures élevées (voir pages 6-7).
 Lisez la section Informations
importantes relatives à la sécurité,
page 5.
[FRENCH]
 Siga las instrucciones de seguridad
a continuación y asegúrese de que
todos en su hogar sepan acerca de este
peligro de quemadura:
• ¡Las superficies de la chimenea se
ponen MUY CALIENTES!
• El vidrio delante de la
chimenea alcanza temperaturas
EXTREMADAMENTE ALTAS y puede
causar quemaduras graves si se toca.
• Mantenga a los niños alejados de
la chimenea en funcionamiento.
Supervise en forma cercana a los niños
en cualquier cuarto donde haya una
chimenea funcionando para impedir el
contacto con el vidrio.
• Mantenga la ropa, mobiliario, gasolina
y otros líquidos inflamables alejados
de la chimenea.
• Aún después de haber apagado el
gas, las superficies de la chimenea
permanecen extremadamente
calientes.
 Asegúrese de colocar las Etiquetas de
advertencia de seguridad de operación
en el lugar donde enciende la chimenea,
para que todos recuerden los peligros
asociados con las altas temperaturas
(ver la páginas 6-7).
 Lea la Información importante de
seguridad en la página 5.
[SPANISH]
3
CONGRATULATIONS!
When you purchased your new gas stove, you joined the ranks of thousands of individuals whose answer to their home heating needs reflects
their concern for aesthetics, efficiency and our environment. We extend
our continued support to help you achieve the maximum benefit and
enjoyment available from your new gas stove.
Thank you for selecting an Innovative Hearth Products LLC (IHP) gas
stove as the answer to your home heating needs.
TABLE OF CONTENTS
Safety and Your Gas Stove............................................... 2-3
Using this Manual........................................................... 4
Important Safety Information.............................................. 5
Homeowner - Attaching Safety In Operation Warnings................ 6
Installer - Attaching Safety In Operation Warnings.................... 7
Appliance Installation, Service, and Maintenance Notices........... 8
Appliance Operation Notices............................................... 8
Warranty Information....................................................... 8
Important Safety And Warning Information.............................. 9
General Information ....................................................... 10
Introduction ................................................................. 11
Location ..................................................................... 11
Orifice Size / Altitude Adjustment ....................................... 12
Smoke Detectors............................................................ 12
The Gas Stove............................................................... 12
Codes and Approvals....................................................... 12
Commonwealth Of Massachusetts Requirements..................... 12
New York City, New York (MEA).......................................... 12
Pre-Installation......................................................... 13-17
Features............................................................ 13
Packaging List..................................................... 13
Ratings............................................................. 13
Specifications / Dimensions..................................... 14
Clearances to Combustibles..................................... 15
Manufactured (Mobile) Home Requirements................. 16
Questions to Ask Building Official.............................. 16
Vent Termination Clearances................................ 16-17
Installation............................................................... 18-29
Typical Installation Sequence ................................. 18
Detailed Installation Steps ...................................... 18
Step 1 Preparation .............................................. 18
4
Step 2 Remove Packaging ...................................... 18
Step 3 Remove Stove From Pallet ............................ 18
Step 4 Remove Front Glass ..................................... 19
Step 5 Remove the barrier ...................................... 19
Step 6 Remove Firebox Contents .............................. 19
Step 7 Remove Cardboard Packaging ......................... 19
Step 8 Install LP Conversion / Options ........................ 19
Step 9 Install Lower Access Door .............................. 20
Step 10 Install Venting .......................................... 20
Step 11 Connect Gas Line ....................................... 24
Step 12 Install Log Set .......................................... 24
Step 13 Reinstall Front Glass .................................. 26
Step 15 Perform Leak Test ...................................... 26
Step 16 Check Appliance Operation ........................... 27
Step 17 Adjust Burner ........................................... 27
Step 18 Install Top, Trivet & Ash Lip .......................... 28
Step 19. Attaching Safety-in-Operation Warnings .......... 28
Operation And Care Of Your Appliance.................................. 29
Gas Controls ...................................................... 29
Control Compartment Access ................................... 29
Variable Flame Height Adjustment ............................ 29
Burn-In Period .................................................... 29
Front Glass Enclosure Panel .................................... 30
Maintenance ...................................................... 31
Replacing A Damaged Barrier.................................. 32
Wiring Diagrams ................................................. 33
Lighting Instructions (English) ................................. 34
Lighting Instructions (French) .................................. 35
Rating Labels ..................................................... 36
Maintenance Schedule .......................................... 37
Troubleshooting .................................................. 38
Replacement Parts List ...................................... 39-41
Accessories ................................................... 42-43
Warming Shelves - Installation Instructions ........................... 44
Warranty..................................................................... 45
Product Reference Information........................................... 46
USING THIS MANUAL
Please read and carefully follow all of the instructions found in this
manual. Please pay special attention to the safety instructions provided
in this manual.
PRODUCT IS SUBJECT TO CHANGE WITHOUT NOTICE
IMPORTANT SAFETY Information
Important Safety Information
L’information de sûreté
importante
1. WARNING: Do not operate appliance
with the glass front removed, cracked
or broken.
1. AVERTISSEMENT. Ne pas utiliser l’appareil 1. ADVERTENCIA: No opere el artefacto con el
si le panneau frontal en verre n’est pas en
frente de vidrio quitado, agrietado o roto.
place, est craqué ou brisé.
2. No use este artefacto si alguna de sus partes
2. Ne pas se servir de cet appareil s’il a été
ha estado bajo agua. Llame de inmediato
plongé dans l’eau, même partiellement.
a un técnico de servicio calificado para
Faire inspecter l'appareil par un technicien
que inspeccione el artefacto y reemplace
qualifié et remplacer toute partie du systéme
cualquier parte del sistema de control y
de contrôle et toute commande qui ont été
cualquier control de gas que haya estado
plongées dans l'eau.
bajo agua.
3. En raison des températures élevées,
2. Do not use this appliance if any part
has been under water. Immediately
call a qualified service technician to
inspect the appliance and to replace
any part of the control system and
any gas control which has been under
water.
3. Due to high temperatures, the appliance should be located out of traffic
and away from furniture and draperies.
4. Children and adults should be alerted
to the hazards of high surface temperature and should stay away to avoid
burns or clothing ignition.
4.
5. Clothing or other flammable material
should not be placed on or near the
appliance.
5.
6. Young children should be carefully
supervised when they are in the same
room as the appliance. Toddlers,
young children, and others may be susceptible to accidental contact burns.
A physical barrier is recommended
if there are at-risk individuals in the
house. To restrict access to a fireplace
or stove, install an adjustable safety
gate to keep toddlers, young children,
and other at-risk individuals out of the
room and away from hot surfaces.
6.
7. Any safety screen, guard or barrier
removed for servicing an appliance
must be replaced prior to operating
the appliance.
8. Installation and repair should be done
by a qualified service person. The
appliance should be inspected before
use and at least annually by a professional service person. More frequent
cleaning may be required due to
excessive lint from carpeting, bedding
material, et cetera. It is imperative
that control compartments, burners,
and circulating air passageways of the
appliance be kept clean. See maintenance instructions on Page 31.
7.
8.
l’appareil devrait être installé dans un
endroit où il y a peu de circulation et loin
du mobilier et des tentures.
Les enfants et les adultes devraient être
informés des dangers que posent les températures de surface élevées et se tenir à
distance afin d’éviter des brûlures ou que
leurs vêtements ne s’enflamment.
On ne devrait pas placer de vêtements
ni d’autres matières inflammables sur
l’appareil ni à proximité.
Les jeunes enfants devraient être surveillés
étroitement lorsqu’ils se trouvent dans la
même pièce que l’appareil. Les tout petits,
les jeunes enfants ou les adultes peuvent
subir des brûlures s’ils viennent en contact
avec la surface chaude. Il est recommandé
d’installer une barrière physique si des
personnes à risques habitent la maison.
Pour empêcher l’accès à un foyer ou à un
poêle, installez une barrière de sécurité
; cette mesure empêchera les tout petits,
les jeunes enfants et toute autre personne
à risque d’avoir accès à la pièce et aux
surfaces chaudes.
Tout écran ou protecteur retiré pour permettre l’entretien de l’appareil doit être
remis en place avant de mettre l’appareil
en marche.
L’installation et la réparation devrait être
confiées à un technicien qualifié. L’appareil
devrait faire l’objet d’une inspection par un
technicien professionnel avant d’être utilisé
et au moins une fois l’an par la suite. Des
nettoyages plus fréquents peuvent être
nécessaires si les tapis, la literie, et cetera
produisent une quantité importante de poussière. Il est essentiel que les compartiments
abritant les commandes, les brûleurs et les
conduits de circulation d’air de l’appareil
soient tenus propres. Voyez les instructions
d’entretien à la Page 31.
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
Información importante de
seguridad
3. Debido a las altas temperaturas, el artefacto
debe situarse fuera de las áreas de tráfico y
lejos del mobiliario y cortinas.
4. Se debe alertar a los niños y adultos sobre
los peligros de las altas temperaturas en la
superficie y que se mantengan alejados para
evitar quemaduras o ignición de la ropa.
5. No debe colocarse ropa u otros materiales
inflamables sobre y cerca del artefacto.
6. Se debe supervisar de cerca a los niños
cuando estén en el mismo cuarto que el
artefacto. Los niños pequeños, los jóvenes
y otras personas pueden ser susceptibles
a quemaduras por contacto accidental. Se
recomienda instalar una barrera física si hay
personas en riesgo en la casa. Para restringir
el acceso a una chimenea o estufa, instale
una puerta de seguridad ajustable para
mantener a los niños pequeños, jóvenes y
otras personas en riesgo fuera del cuarto y
lejos de las superficies calientes.
7. Cualquier malla o resguardo de seguridad
quitado para dar servicio a un artefacto, debe
reinstalarse antes de operar el artefacto.
8. Una persona de servicio competente debe
realizar la instalación y reparación. Una
persona de servicio profesional debe
inspeccionar el artefacto antes de usar al
menos una vez por año. Se puede requerir
limpieza más frecuente debido a la pelusa
excesiva del alfombrado, del material de
cobijas, etc. Es imprescindible mantener
limpios los compartimientos de control, los
quemadores y los pasajes de circulación del
aire del artefacto. Ver las instrucciones de
mantenimiento en la página 31.
5
HOMEOWNER’S INSTRUCTIONS - ATTACHING SAFETY IN OPERATION WARNINGS
Attaching Safety in Operation Warnings
Your fireplace has been furnished with safety instruction labels that are to be affixed to the operation and
control point of the fireplace. A safety instruction
label should be affixed to the wall switch plate where
the fireplace is turned on and off (See Figure A) or
wall thermostat (See Figure B) and if used on the
remote control handheld transmitter (Figure C).
The warnings should already have been put in place
when the fireplace initial set-up was completed.
If they are not affixed at these spots, locate the
multi-lingual adhesive labels provided with these
instructions and proceed as follows:
1. Locate the wall switch or wall thermostat that
controls the fireplace (verify the switch operates
the fireplace by turning it on and off). Clean the
wall switch plate or wall thermostat thoroughly
to remove any dust and oils. Affix the label to
the surface of the plate of the wall switch that
controls the fireplace (Figure A) or the wall
thermostat (Figure B). Choose the language
primarily spoken in the home.
2. If a remote control is used to control the fireplace,
locate the transmitter and clean it thoroughly
to remove any dust and oils. Affix the label to
the surface of handheld transmitter (Figure C).
Choose the language primarily spoken in the
home.
3. If you are unable to locate the labels, please
contact IHP or your nearest IHP dealer to receive
additional safety instruction labels free of charge.
Cat. No. H8024 Replacement Label Kit
IHP
IronStrike.us.com
Apposition des mises en garde relatives
à la sécurité d’utilisation
Colocación de advertencias de seguridad
en operación
Votre foyer a été livré avec des étiquettes de sécurité qui
doivent être collées à côté des dispositifs de contrôle
du foyer. Une étiquette de sécurité doit être collée sur
la plaque de l’interrupteur contrôlant l’allumage du
foyer (voir Figure A) ou sur le thermostat mural (voir
Figure B) et, le cas échéant, sur le boîtier de la télé­
commande (Figure C). Les mises en garde auraient dû
être collées au moment de l’installation initiale du foyer.
Si ce n’est pas le cas, prenez les étiquettes adhésives
multilingues fournies avec ces instructions et procédez
comme suit:
1. Repérez l’interrupteur ou le thermostat mural
qui contrôle le foyer (vérifiez que l’interrupteur
contrôle le fonctionnement du foyer en le faisant
basculer de Marche à Arrêt, et vice-versa). Nettoyez
soigneusement la plaque murale de l’interrupteur
ou le thermostat mural pour éliminer la poussière
et les traces de graisse ou d’huile. Collez l’étiquette
sur la surface de la plaque de l’interrupteur mural
qui contrôle le foyer (Figure A) ou du thermostat
mural (Figure B). Choisissez la langue qui est
principalement parlée dans la résidence du
propriétaire.
2. Si une télécommande est utilisée pour contrôler
le foyer, nettoyez la soigneusement pour éliminer
la poussière et les traces de graisse ou d’huile.
Collez l’étiquette sur le boîtier de la télécommande
(Figure C). Choisissez la langue qui est principale­
ment parlée dans la résidence du propriétaire.
3. Si vous ne parvenez pas à localiser les étiquettes, s’il
vous plaît contactez IHP ou votre revendeur le plus
proche pour recevoir IHP étiquettes d’instructions
de sécurité supplémentaires gratuitement.
Su chimenea incluye etiquetas de instrucciones de
seguridad que deben colocarse en el punto de operación
y control de la chimenea. Se debe colocar una etiqueta de
instrucciones de seguridad en la placa del interruptor de
pared desde el cual se enciende y se apaga la chimenea
(ver la Figura A) o en el termostato de pared (ver la Figura
B) y en el transmisor de control remoto (Figura C) si
se usa. Las advertencias ya deben haberse colocado
cuando se completó la instalación inicial de la chimenea.
Si no están colocadas en estos lugares, encuentre las
etiquetas adhesivas multilingües proporcionadas con
estas instrucciones y prosiga de la siguiente manera:
1. Identifique el interruptor o el termostato de pared
que controla la chimenea (verifique que el interruptor
opera la chimenea encendiéndola y apagándola).
Limpie bien la placa del interruptor o el termostato de
pared para quitar el polvo y aceite. Pegue la etiqueta
en la superficie de la placa del interruptor que controla
la chimenea (Figura A) o en el termostato de pared
(Figura B). Seleccione el idioma que más se habla
en la casa.
2. Si se usa un control remoto para controlar la
chimenea, encuentre el transmisor y límpielo bien
para quitar el polvo y aceite. Pegue la etiqueta en la
superficie del transmisor (Figura C). Seleccione el
idioma que más se habla en la casa.
3. Si usted es incapaz de localizar las etiquetas, por favor
póngase en contacto con IHP, o con su distribuidor
más cercano IHP recibir instrucción etiquetas de
seguridad adicionales sin costo.
Étiquettes de remplacement, n° cat. H8024
Note: English is red text on clear label. French and
Spanish are white text on black label.
IHP
IronStrike.us.com
Remarque : Le texte anglais est rouge sur un support
transparent. Le texte français et espagnol est blanc
sur un support noir.
SAFETY LABEL
DIAGRAMS
DIAGRAMMES DES ÉTIQUETTES
DE SÉCURITÉ
Juego de etiquetas de repuesto - Nº de cat. H8024
IHP
IronStrike.us.com
Nota: La etiqueta en inglés es transparente con texto
rojo. Las etiquetas en francés y español son negras
con texto blanco.
DIAGRAMAS DE ETIQUETAS
DE SEGURIDAD
Illustrations are for example only.
Your accessories may be different.
Les illustrations sont par exemple
uniquement. Vos accessoires
peuvent être différents.
Figure A
Figure B
Las ilustraciones son sólo ejemplos.
Tu accesorios pueden ser diferentes.
6
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
Figure C
INSTALLER INSTRUCTIONS - ATTACHING SAFETY IN OPERATION WARNINGS
It is the installers responsibility to ensure these warnings are properly affixed during installation. These warning labels are a
critical step in informing consumers of safe operation of this appliance.
Attaching Safety in Operation Warnings
It is required that the safety instruction labels furnished with the fireplace be affixed to the operation
and control point of the fireplace. A safety instruction
label must be affixed to the wall switch plate where
the fireplace is turned on and off (See Figure A)
or wall thermostat (See Figure B) and if used on
the remote control handheld transmitter (Figure
C). To properly complete the installation of this
fireplace, locate the multi-lingual adhesive labels
provided with the Care and Operation Instructions
and proceed as follows:
1. Locate the wall switch or wall thermostat that
controls the fireplace (verify the switch operates
the fireplace by turning it on and off). Clean the
wall switch plate or wall thermostat thoroughly
to remove any dust and oils. Affix the label to
the surface of the plate of the wall switch that
controls the fireplace (Figure A) or the wall
thermostat (Figure B). Choose the language
primarily spoken in the home. If unknown, affix
the English language label.
2. If a remote control is used to control the fireplace,
locate the transmitter and clean it thoroughly
to remove any dust and oils. Affix the label to
the surface of handheld transmitter (Figure C).
Choose the language primarily spoken in the
home. If unknown, affix the English language
label.
3. If you are unable to locate the labels, please
contact IHP or your nearest IHP dealer to receive
additional safety instruction labels free of charge.
Cat. No. H8024 Replacement Label Kit
IHP
IronStrike.us.com
Note: English is red text on clear label. French and
Spanish are white text on black label.
Apposition des mises en garde relatives
à la sécurité d’utilisation
Il est impératif que les étiquettes de sécurité fournies
avec le foyer soient collées à côté des dispositifs
de contrôle du foyer. Une étiquette de sécurité doit
être collée sur la plaque de l’interrupteur contrôlant
l’allumage du foyer (voir Figure A) ou sur le thermostat
mural (voir Figure B) et, le cas échéant, sur le boîtier
de la télécommande (Figure C). Pour achever l’instal­
lation correcte de ce foyer, procédez comme suit avec
les étiquettes adhésives en langues étrangères fournies
avec les instructions d’utilisation et d’entretien :
1. Repérez l’interrupteur ou le thermostat mural qui
contrôle le foyer (vérifiez que l’interrupteur
contrôle le fonctionnement du foyer en le faisant
basculer de Marche à Arrêt, et vice-versa). Nettoyez
soigneusement la plaque murale de l’interrupteur
ou le thermostat mural pour éliminer la poussière
et les traces de graisse ou d’huile. Collez l’étiquette
sur la surface de la plaque de l’interrupteur mural
qui contrôle le foyer (Figure A) ou du thermostat
mural (Figure B). Choisissez la langue qui est
principalement parlée dans la résidence du
propriétaire. En cas de doute, collez l’étiquette en
anglais.
2. Si une télécommande est utilisée pour contrôler
le foyer, nettoyez la soigneusement pour éliminer
la poussière et les traces de graisse ou d’huile.
Collez l’étiquette sur le boîtier de la télé­
commande (Figure C). Choisissez la langue qui est
principalement parlée dans la résidence du proprié­
taire. En cas de doute, collez l’étiquette en anglais.
3. Si vous ne parvenez pas à localiser les étiquettes, s’il
vous plaît contactez IHP ou votre revendeur le plus
proche pour recevoir IHP étiquettes d’instructions
de sécurité supplémentaires gratuitement.
Étiquettes de remplacement, n° cat. H8024
IHP
IronStrike.us.com
Remarque : Le texte anglais est rouge sur un support
transparent. Le texte français et espagnol est blanc
sur un support noir.
SAFETY LABEL
DIAGRAMS
DIAGRAMMES DES ÉTIQUETTES
DE SÉCURITÉ
Colocación de advertencias de seguridad
en operación
Se requiere que las etiquetas de instrucciones de
seguridad incluidas con la chimenea se coloquen en
el punto de operación y control de la misma. Se debe
colocar una etiqueta de instrucciones de seguridad
en la placa del interruptor de pared desde el cual se
enciende y se apaga la chimenea (ver la Figura A) o en el
termostato de pared (ver la Figura B) y en el transmisor
de control remoto (Figura C) si se usa. Para completar
correctamente la instalación de esta chimenea,
encuentre las etiquetas adhesivas multilingües incluidas
con las instrucciones de cuidado y operación y haga
lo siguiente:
1. Identifique el interruptor o el termostato de pared
que controla la chimenea (verifique que el interruptor
opera la chimenea encendiéndola y apagándola).
Limpie bien la placa del interruptor o el termostato
de pared para quitar el polvo y aceite. Pegue la
etiqueta en la superficie de la placa del interruptor que
controla la chimenea (Figura A) o en el termostato
de pared (Figura B). Seleccione el idioma que
más se habla en la casa. Si no sabe cuál es, use la
etiqueta en inglés.
2. Si se usa un control remoto para controlar la
chimenea, encuentre el transmisor y límpielo bien
para quitar el polvo y aceite. Pegue la etiqueta en
la superficie del transmisor (Figura C). Seleccione
el idioma que más se habla en la casa. Si no sabe
cuál es, use la etiqueta en inglés.
3. Si usted es incapaz de localizar las etiquetas, por favor
póngase en contacto con IHP, o con su distribuidor
más cercano IHP recibir instrucción etiquetas de
seguridad adicionales sin costo.
Juego de etiquetas de repuesto - Nº de cat. H8024
IHP
IronStrike.us.com
Nota: La etiqueta en inglés es transparente con texto
rojo. Las etiquetas en francés y español son negras
con texto blanco.
DIAGRAMAS DE ETIQUETAS
DE SEGURIDAD
Illustrations are for example only.
Your accessories may be different.
Les illustrations sont par exemple
uniquement. Vos accessoires
peuvent être différents.
Figure A
Figure B
Figure C
Las ilustraciones son sólo ejemplos.
Tu accesorios pueden ser diferentes.
7
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
Appliance Installation, Service, and
Maintenance Notices
WARNING: Improper installation, adjustment, alteration,
service or maintenance can cause injury or property damage.
Refer to the owner’s information manual provided with this
appliance. For assistance or additional information consult a
qualified installer, service agency or the gas supplier.
AVERTISSEMENT : Une installation, un réglage, une
modification, une réparation ou un entretien mal effectué
peut causer des dommages matériels ou des blessures.
Voir la notice de l’utilisateur qui accompgne l’appareil.
Pour de l’aide ou des renseignements supplémentaires,
consultez un installateur, un technicien agréé ou le
fournisseur de gaz.
If the barrier becomes damaged, the barrier shall be
replaced with the manufacturer’s barrier for this appliance.
Si l’écran est endommagé, il doit être remplacé par
celui fournit par le fabricant de cet appareil.
Reinstall any barrier removed before operating the
appliance. The barrier is designed to reduce the risk of
burns from hot glass. Do not operate the appliance without
the barrier installed.
Appliance Operation Notices
These gas stoves are vented gas appliances. Do not burn
wood or other material in these appliances.
Only trim kit(s) supplied by the manufacturer shall be used
in the installation of this appliance.
Seules les trousses de garniture fournies par le fabricant
doivent être utilisées pour l’installation de cet appareil.
These appliances are designed to operate on natural gas or
propane gas only. The use of other fuels or combinations of
fuels will degrade the performance of this system and may
be dangerous.
These appliances must not be connected to a chimney or flue
serving a separate solid fuel burning appliance.
Provide adequate clearances around air openings and
adequate accessibility clearance for service and proper operation. Never obstruct the front openings of the appliance.
Any change to this appliance and/or its operating controls is
dangerous. Improper installation or use of this appliance can
cause serious injury or death from fire, burns, explosion or
carbon monoxide poisoning.
These appliances are designed as supplemental heaters.
Therefore, it is advisable to have an alternate primary heat
source when installed in a dwelling.
CARBON MONOXIDE POISONING: Early signs of carbon
monoxide poisoning are similar to the flu with headaches,
dizziness and/or nausea. If you have these signs, obtain fresh
air immediately. Turn off the gas supply to the appliance and
have it serviced by a qualified professional, as it may not be
operating correctly. Some people are more affected by carbon
monoxide than others, including pregnant women, people with
heart or lung disease or anemia, those under the influence of
alcohol, and those at high altitudes.
Turn off gas and electrical power to the appliance and allow
it to cool before cleaning or servicing the appliance.
Warranty Information
Your gas appliance is covered by a limited 20-year warranty.
You will find a copy of the warranty accompanying this manual.
Please read the warranty to be familiar with its coverage.
Retain this manual. File it with your other documents for future
reference.
Failure to comply with the installation and operating
instructions provided will result in an improperly installed
and operating appliance, voiding its warranty.
Do not attempt to alter or modify the construction of the
appliance or its components. Any modification or alteration
may void the warranty, certification, and listings of this unit.
8
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
IMPORTANT SAFETY AND WARNING
INFORMATION
 INSTALLER: THESE INSTRUCTIONS ARE TO REMAIN WITH THE
HOME OWNER!
 FOR YOUR SAFETY do not install or operate this appliance without
first reading and understanding this manual. Any installation or
operation of the appliance deviating from that which is stated
in this manual WILL void the warranty and may be hazardous.
 IHP, its employees, or any of its representatives assume no
responsibility for any damages caused by an inoperable, inadequate, or unsafe condition as a result of any improper operation,
service or installation procedures, whether direct or indirect.
 DO NOT ATTEMPT TO SERVICE THE APPLIANCE YOURSELF.
 Do not make any make-shift compromises during installation.
Any modification or alteration may result in damage to the appliance or dwelling and will void the warranty, certification and
listings of this unit.
 Failure to use manufacturer provided parts, variations in techniques and construction materials or practices other than those
described in this manual may create a fire hazard and void the
limited warranty.
 This gas appliance must be equipped for the proper fuel type
and altitude at which it will be operated. Any operation outside
the parameters outlined in this manual may result in a hazardous condition and will void the warranty. Please carefully read
the sections pertaining to these subjects and/or be sure your
appliance is properly equipped.
 Plated surfaces must be cleaned with glass cleaner and a clean
soft cloth before firing the first time or fingerprints will remain
permanently. NEVER use brass polish to clean plated surfaces,
this will remove the plating!!!
 CAUTION: Hot while in operation. Do not touch. Severe Burns
may result. Keep children, clothing furniture, gasoline and other
liquids having flammable vapors away.
ATTENTION: L’appareil est chaud lorsqu’il fonctionne. Ne
pas toucher l’appareil. Risque de brûlures graves. Surveiller
les enfants. Garder les vêtements, les meubles, l’essence
ou autres liquides produisant des vapeur inflammables loin
de l’appareil.
 Clearances are in accordance with local installation codes and
the requirements of the gas supplier.
Les dégagements sont conformes aux codes d’installation
locaux et aux exigences du foumisseur de gaz.
 This appliance is only for use with the type of gas indicated on
rating plate. This appliance is not convertible for use with other
gases, unless a certified kit is used.
Cet appareil doit être utilisé uniquement avec les types de
gaz indiqués sur la plaque signalétique. Ne pas l’utiliser
avec d’autres gaz sauf si un kit de conversion certifié est
installé.
WARNING
Improper installation or use of this appliance can
cause serious injury or death from fire, burns,
explosion or carbon monoxide poisoning.
 Never use solid fuels such as wood, paper, cardboard, coal, or
any flammable liquids, etc., in this appliance.
WARNING
Failure to comply with these installation instructions
will result in an improperly installed and operating
appliance, voiding its warranty.
9
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
Installations at Altitudes of 0 to 4500 feet - Units are tested and
approved for elevations of 0 to 4500 feet (0 to 1370 meters).
GENERAL INFORMATION
NOTE: Installation and repair should be performed by a qualified
service person. The appliance should be inspected annually by a
qualified professional service technician. More frequent inspections
and cleanings may be required due to excessive lint from carpeting,
bedding material, etc. It is imperative that the control compartment,
burners and circulating air passage ways of the appliance be kept clean.
Installations at Altitudes above 4500 ft.For elevations above 4500 feet (1370 meters), install the unit
according to the regulations of the local authorities having
jurisdiction and, in the USA, the latest edition of the National Fuel
Gas Code (ANSI Z223.1) or, in Canada, the latest edition of the
CAN/CGA-B149.1 and CAN/CGA-B149.2 codes.
S'assurer que le brùleur et le compartiment des commandes sont
propres. Voir les instructions d'installation et d'utilisation qui
accompagnent l'appareil.
Table 4 shows the units' gas orifice size for the elevations indicated:
Provide adequate clearances around air openings and adequate accessibility clearance for service and proper operation. Never obstruct the
front openings of the appliance.
These appliances are designed to operate on natural or propane
gas only.
These millivolt models come standard with the manually-modulated
gas valve; flame appearance and heat output can be controlled at
the gas valve.
These appliances are designed as supplemental heaters. Therefore, it is
advisable to have an alternate heat source when installed in a dwelling.
Table 1 shows the BTU input for each model:
Input (BTU/HR) Manually-Modulated Gas Valves (millivolt models)
Models
Natural Gas
Propane
CI1500DVF
17,500 to 28,000
20,500 to 27,000
CI2500DVF
25,500 to 38,500
26,500 to 34,500
Table 1
Tables 2 and 3 show the units' gas pressure requirements:
Inlet Gas Supply Pressure
(all models)
Fuel #
Minimum
Maximum
Natural Gas
4.5" WC (1.12 kPa)
10.5" WC (2.61 kPa)
Propane
11.0" WC (2.73 kPa)
13.0" WC (3.23 kPa)
Table 2
Manifold Gas Supply Pressure
(millivolt models)
Fuel #
Low
High
Natural Gas
(Lo) 1.6" WC (.40 kPa)
(Hi) 3.5" WC (.87 kPa)
Propane
(Lo) 6.3" WC (1.57 kPa)
(Hi) 10.0" WC (2.49 kPa)
Burner Orifice Sizes
Model
No.
Natural
Gas
Propane
Gas
Elevation
Feet (meters)
CI1500DVF
#37 (.104")
1.55mm (.061")
0-4500 (0-1372)
CI2500DVF
.121"
1.75mm (.068")
0-4500 (0-1372)
Table 4
The millivolt appliances are manually controlled and feature a spark
igniter (piezo) that allows the appliance's pilot gas to be lit without the
use of matches or batteries. This system provides continued service
in the event of a power outage.
Do not use these appliances if any part has been under water. Immediately call a qualified, professional service technician to inspect
the appliance and to replace any parts of the control system and any
gas controls which have been under water.
Ne pas se servir de cet appareil s'il a été plongé dans l'eau,
complètement ou en partie. Appeler un technicien qualifié
pour inspecter l'appareil et remplacer toute partie du système
de contrôle et toute commande qui ont été plongés dans l'eau.
This appliance may be installed in an aftermarket permanently
located, manufactured home (USA only) or mobile home, where
not prohibited by local codes.
Cet appareil peut être installé dans un maison préfabriquée
(É.-U. seulement) ou mobile déjà installée à demeure si les
réglements locaux le permettent.
Test gauge connections are provided on the front of the millivolt gas
control valve (identified IN for the inlet and OUT for the manifold side).
Propane tanks are at pressures that will cause damage to valve components. Verify that the tanks have step down regulators to reduce the
pressure to safe levels.
The appliance must be isolated from the gas supply piping system
by closing its equipment shutoff valve during any pressure testing of
the gas supply piping system at test pressures equal to or less than
1/2 psig (3.5 kPa).
The appliance and its appliance main gas valve must be disconnected
from the gas supply piping system during any pressure testing of that
system at test pressures in excess of 1/2 psig (3.5 kPa).
Table 3
10
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
INTRODUCTION
WARNING
This appliance must be properly connected to a
venting system. Operation of this gas appliance
when not connected to a properly installed and
maintained venting system can result in carbon
monoxide (CO) poisoning and possible death.
WARNING
Failure to comply with the installation and operating
instructions provided in this document will result in
an improperly installed and operating appliance,
voiding its warranty. Any change to this appliance
and/or its operating controls is dangerous.
AVERTISSEMENT
Une installation ou une utilisation incorrecte de
cet appareil risque de provoquer un incendie,
des brûlures, une explosion, une intoxication au
monoxyde de carbone, ainsi que des blessures
graves, voire mortelles.
WARNING
Young children should be carefully supervised when
they are in the same room as the appliance.
NOTE: An Optional Screen Panel for the glass is available (see Accessory section for ordering information).
The stove models covered in this manual are Direct-Vent sealed
combustion vented gas stove heaters designed for residential and
manufactured home applications. Direct-Vent appliances operate
with the combustion chamber isolated from the inside atmosphere.
All air for combustion is brought in from the outside and exhaust
gases are vented through the same direct-vent, vent system.
These millivolt appliances are designed to operate on either natural or
propane gas. A millivolt gas control valve with piezo ignition system
provides safe, efficient operation. External electrical power is required
to operate the optional electrically powered components if installed.
LOCATION
In selecting the location, the aesthetic and functional use of the
appliance are primary concerns. However, vent system routing to the
exterior and access to the fuel supply are also important. Consideration should be given to traffic ways, furniture, draperies, etc., due
to elevated surface temperatures.
Considerations Should Include:
• Existing Chimneys
• Aesthetic Considerations
• Roof Design (Rafter Locations and Roof Pitch)
• Room Traffic
• Proximity to Combustibles
• Proximity for Optimum Heat Transfer
• Electrical Wiring (if optional blower is installed)
The installation of this stove will require some research. Once your
options are determined, consult with your local building department
who will be able to give you the necessary installation requirements for
your area (Is a building permit required?, Rooms where installation may
not be allowed?, etc.).
11
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
ORIFICE SIZE/ALTITUDE ADJUSTMENT
For altitudes above 4,500 FT (1370 M), the orifice should be de-rated by
4% for every 1,000 feet to maintain the proper ratio of gas to air. Improper
orifice sizing may result in damage and unsafe conditions. Changing the
orifice should only be done by a qualified service technician. Contact your
IHP dealer for proper orifice sizes (see Page 10 for more information).
Install the unit according to the regulations of the local authorities having
jurisdiction and, in the USA, the latest edition of the National Fuel Gas
Code (ANSI Z223.1) or, in Canada, the latest edition of the CAN/CGAB149.1 and B149.2 codes.
In Canada - CAN/CGA-2.17-M91 (R2009) (high altitude):
THE CONVERSION SHALL BE CARRIED OUT BY A MANUFACTURER’S
AUTHORIZED REPRESENTATIVE, IN ACCORDANCE WITH THE REQUIREMENTS OF THE MANUFACTURER, PROVINCIAL OR TERRITORIAL
AUTHORITIES HAVING JURISDICTION AND IN ACCORDANCE WITH
THE REQUIREMENTS OF THE CAN/CGA-B149.1 OR CAN/CGA-B149.2
INSTALLATION CODES.
SMOKE DETECTORS
Since there are always several potential sources of fire in any home, we
recommend installing smoke detectors. If possible, install the smoke
detector in a hallway adjacent to the room (to reduce the possibility of
occasional false activation from the heat produced by the appliance). If
your local code requires a smoke detector be installed within the same
room, you must follow the requirements of your local code. Check with
your local building department for requirements in your area.
THE GAS STOVE
• Must conform with all local, state and national installation codes.
In the absence of local codes, the installation must conform with
(USA) National Fuel Gas Code NFPA 54/ANSI Z223.1 - latest edition
or, in Canada, the CAN/CGA-B149.1 codes - latest edition. Refer to
the National Fuel Gas Code and local zoning and code authorities for
details on installation requirements.
• Manufactured home installations (USA only) must conform with the
Manufactured Home Construction and Safety Standard, Title 24 CFR,
Part 3280, or, when such a standard is not applicable, the Standard for
Manufactured Home Installations, ANSI/NCSBCS A225.1, or Standard
for Gas Equipped Recreational Vehicles and Mobile Housing, CSA
Z240.4.
• Must be vented directly to the outside in accordance with the latest
edition of the National Fuel Gas Code.
• Has been certified for use with either natural gas or propane.
CODES AND APPROVALS
Certification
Gas appliances must be tested and certified by a nationally recognized
testing and certification laboratory to ANSI (American National Standard
Institute) gas appliance safety standards.
These appliances comply with National Safety Standards and are tested
and listed to ANSI Z21.88 (in Canada, CSA-2.33), and CAN/CGA-2.17-M91
in both USA and Canada, as vented gas heaters.
It has met all necessary ANSI Standards and is fully certified for installation in any community. If there are any questions or if you need further
substantiation either write to or call your IHP dealer. If you have further
questions, please contact IHP.
Check all local building and safety codes before installation. The installation instructions and appropriate code requirements must be followed
exactly and without compromise. In the absence of local codes the following standards and codes must be followed.
The Installation must conform with local codes or, in the absence of local
codes, with the (USA) National Fuel Gas Code NFPA 54/ANSI Z223.1 latest edition or, in Canada, the CAN/CGA-B149.1 codes - latest edition.
This appliance, when installed, must be electrically grounded in accordance
with local codes, or in the absence of local codes, the National Electrical
Code ANSI/NFPA 70-latest edition, or the Canadian Electrical Code, Part
1, CSA C22.1-latest edition.
COMMONWEALTH OF MASSACHUSETTS REQUIREMENTS
These appliances are approved for installation in the US state of Massachusetts if the following additional requirements are met:
• Install this appliance in accordance with Massachusetts Rules and
Regulations 248 C.M.R. Sections 4.00 through 8.00.
• Installation and repair must be done by a plumber or gas fitter licensed
in the Commonwealth of Massachusetts.
• The flexible gas line connector used shall not exceed 36 inches (92
centimeters) in length.
• The individual manual shut-off must be a T-handle type valve.
Massachusetts Horizontal Vent Requirements
In the Commonwealth of Massachusetts, horizontal terminations installed
less than seven (7) feet above the finished grade must comply with the
following additional requirements:
• A hard wired carbon monoxide detector with an alarm and battery
back-up must be installed on the floor level where the gas fireplace
is installed. The carbon monoxide detector must comply with NFPA
720, be ANSI/UL 2034 listed and be ISA certified.
• A metal or plastic identification plate must be permanently mounted to
the exterior of the building at a minimum height of eight (8) feet above
grade and be directly in line with the horizontal termination. The sign
must read, in print size no less than one-half (1/2) inch in size, GAS
VENT DIRECTLY BELOW. KEEP CLEAR OF ALL OBSTRUCTIONS.
• Is not for use with solid fuels.
• Is approved for sitting rooms and/or bedrooms.
NEW YORK CITY, NEW YORK (MEA)
12
Installation of these appliances are approved for installation in New York
City in the US state of New York.
This appliance is equipped with orifices sized for operation with natural gas.
PRE-INSTALLATION
The appliance can be converted to burn LP gas (liquid propane) by installing a natural gas to propane conversion kit (provided)
FEATURES
Orifices and instructions necessary for LP/propane conversion are provided
in the gas conversion kit.
Installation Options
Residential
Top Vent - vertical or horizontal termination
Manufactured (mobile) home
Natural gas (NG) or propane (LP)
Bedrooms
Optional wall-mounted or remote thermostat
This appliance comes from the factory equipped to burn natural gas at a
specified elevation. Only IHP conversion kits can be used to convert from
NG to LP or LP to NG. Contact your IHP dealer for details.
Specifications
Pipe:Type - direct-vent
Recommended manufacturer*
Secure Vent® by IHP*
Diameter - 6-5/8” x 4” for all installations
Venting
This appliance can be vented with Secure Vent® direct-vent pipe. Coaxial
pipe diameters are 6-5/8” outer and 4” inner. The combustion air for this
stove is drawn from outside the house through the outer DV (direct-vent)
pipe. Room air is not required for combustion.
When planning your installation, select the correct length of vent pipe
for your particular requirements. Determine the minimum clearance to
combustibles from the rear of the unit to the wall. It is also important
to note the thickness of the wall. Before cutting the vent hole through
the wall make sure that ALL vent and termination clearances (see Page
17) will be met.
Stove Packaging List
one - log set located in firebox
one - ember strip located beneath stove body (on pallet)
one - bag of glowing embers located in the firebox
one - envelope containing the literature package which consists of
the installation and operation manual; located on the top of the
firebox
one - cast iron top
one - trivet
one - natural gas to propane conversion kit
one - ash lip
one - lower access door
four - leg levelers
Electrical
The optional blower requires 120 Volts AC for operation. The stove is
not dependent on the blower or an outside electrical supply to operate.
WARNING - Electrical Grounding Instructions - This appliance
is equipped with a three-prong (grounding) plug for your protection against shock hazard and should be plugged directly
into a properly grounded three-prong receptacle. Do not cut or
remove the grounding prong from this plug.
Options
• Wall-Thermostat, Switch or Timer
• Remote Control
• Blower Kit
Millivolt Valve
• Firebox Liner Kits
• Warming Shelves
• Firescreen Kits
This appliance is operated with a millivolt valve and therefore burns
during a power outage.
Fuel
THIS APPLIANCE IS EQUIPPED FOR NATURAL GAS.
RATINGS
CI1500DVF
CI2500DVF
NATURAL GAS
LP GAS
NATURAL GAS
LP GAS
17,500 to 28,000
20,500 to 27,000
25,500 to 38,500
26,500 to 34,500
Manifold Pressure (IN. WC)
3.5
10.0
3.5
10.0
Min. Inlet Pressure (IN. WC)
4.5
11
4.5
11
P4 Efficiency w
67%
65%
67%
64%
Steady-State Efficiency v
85%
87%
83%
85%
#37 (.104”)
1.55mm (.061”)
.121”
1.75mm (.068”)
Max/Min Input BTUh 0-4500 FT/0-1370 M u
Orifice (DMS) 0-4500 FT/0-1370 M u
uUnit factory equipped for 0-4500 FT/0-1370 M elevation.
vThe Steady State Efficiency numbers based on maximum vent configuration.
wTested to CSA P.4.1-09 “Testing Method for Measuring Annual Fireplace Efficiency.
Electrical Rating: 120 VAC, 60 HZ, Less Than 2 Amps
Based on CSA P.4.1-09
13
* Other approved chimney brand is Simpson Dura-Vent DV-GS.
SPECIFICATIONS: Serefina™
Dimensions
CI1500DVF
F
E
(with ashlip)
CI2500DVF
A
24-1/2” (622 mm)
30-1/2” (775 mm)
B
27-1/2” (699 mm)
28-1/2” (724 mm)
C
19” (483 mm)
22” (559 mm)
D
7” (178 mm)
7” (178 mm)
E
20-1/2” (521 mm)
23-1/2” (597 mm)
F
6” (152 mm)
6” (152 mm)
G
28” (711 mm)
29” (737 mm)
H
40” (1016 mm)
48-1/2” (1232 mm)
Specifications
CI1500DVF
CI2500DVF
Min./Max
BTU/hr Input - NG
17,500 / 28,000
25,500 / 38,500
Min./Max
BTU/hr Input - LP
20,500 / 27,000
26,500 / 34,500
DV Vent Size
4” inner / 6-5/8” outer
4” inner / 6 5/8” outer
Room Fan CFM
150
150
Weight (lb)
206
290
Efficiencies
CI1500DVF
CI2500DVF
EnerGuide P4
67% (NG)
65% (LP)
67% (NG)
64% (LP)
Steady State
Efficiency *
85% (NG)
87% (LP)
83% (NG)
85% (LP)
H
(with optional warming shelves)
Based on CSA P.4.1-09
Diagrams, illustrations and photographs are not to scale – consult installation instructions. Product designs, materials, dimensions, specifications,
colors and prices are subject to change or discontinuance without notice.
A
C
*Based on maximum
vent configuration.
G
B
L
E
N
D
14
Figure 1
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
N
O
X
Clearance To Combustibles and Alcove Dimensions
Minimum Clearances to Combustibles
Side View / Rear Wall or Alcove Clearances
Clearances To Combustible Materials / Floor Protection
• The location should also be free of electrical, plumbing or other
heating/air conditioning ducting.
• Due to high temperatures, this appliance should be located out
of traffic and away from furniture, draperies and not in windy or
drafty areas.
• This appliance can be installed in most residential room configurations, parallel to a rear or adjacent wall, or in an alcove that allows
for the minimum clearances to combustible surfaces. Your local
building inspector should review your plans prior to installation.
• When installing this appliance, provide adequate clearances for
the purposes of servicing and proper operation.
• As determined through the safety certification of this unit, a minimum
clearance to combustible materials must be maintained around
specific areas of the gas appliance. (See Table 5 and Figures 2A,
2B and 2C).
*A
H
D
L
E
N
N
O
X
Clearances
CI1500DVF
CI2500DVF
A (minimum)
*10” (254 mm)
*10” (254 mm)
B (minimum)
*14-1/4” (362 mm)
*17-1/4” (438 mm)
C (minimum)
*15-7/8” (403 mm)
*19” (483 mm)
D (minimum)
4”(102 mm)
4”(102 mm)
E (minimum)
2” (51 mm)
2” (51 mm)
F (minimum)
4” (102 mm)
4” (102 mm)
G (minimum)
0” (0 mm)
0” (0 mm)
H (minimum)
***62” (1575 mm)
***62” (1575 mm)
I (minimum)
**28-1/2” (724 mm)
**34-1/2” (876 mm)
J (MAXIMUM)
48” (1219 mm)
48” (1219 mm)
Figure 2A
G
J
Top View / Rear Wall or Alcove Clearances
D
*B
Table 5
E
E
* Dimensions with a single asterisk are reference dimensions only.
** If the optional warming shelves are installed, a greater alcove width is
required as follows:
CI1500DVF - 44" (1118 mm) min.
CI2500DVF - 52-1/2" (1334 mm) min.
I
***This includes any projections such as shelves, windowsills, mantels, etc.
above the appliance.
Figure 2B
NOTE: Recommended clearance zone from the front of the appliance to combustibles is 36 inches (914 mm) minimum.
Top View / Corner Clearances
Floor Protection
When installed directly on carpeting, tile (see Note below) or other
combustible material other than wood flooring, the appliance shall
be installed on a metal or wood panel extending the full width and
depth of the stove body.
F
NOTE: Ceramic tile is non-combustible and does not require a wood
or metal panel under the appliance.
Vent Clearances - All Models
For Horizontal Sections:..................At Wall Firestops:
Top - 3" (76.2 mm) min..............Top - 3" (76.2 mm) min.
Sides - 1" (25.4 mm) min...........Sides - 1" (25.4 mm) min.
Bottom - 1" (25.4 mm) min.........Bottom - 1/2" (12.7 mm) min.
For Vertical Sections:
Sides - 1" (25.4 mm) min.
*C
F
Figure 2C
15
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
MANUFACTURED (MOBILE) HOME REQUIREMENTS
TERMINATION HEIGHTS FOR VENTS ABOVE
FLAT OR SLOPED ROOFS
Horizontal Overhang
These models may be installed in an aftermarket permanently
located, manufactured home, where not prohibited by local codes.
When installed in Manufactured Housing the following supplemental
requirements must be met:
H*
Storm Collar
X
12
Flashing
Roof Pitch is X/12
1 inch (25.4 mm) Minimum
Clearance to Combustibles
Concentric
Vent Pipe
*H = MINIMUM HEIGHT FROM ROOF TO
LOWEST DISCHARGE OPENING OF VENT
The vent/air intake termination clearances
above the high side of an angled roof is as
follows:
Roof Pitch.................. Feet
Meters
Flat to 6/12................. 1.0
0.3
6/12 to 7/12................ 1.25
0.38
7/12 to 8/12................ 1.5
0.46
8/12 to 9/12................ 2.0
0.61
9/12 to 10/12.............. 2.5
0.76
10/12 to 11/12............ 3.25
0.99
11/12 to 12/12............ 4.0
1.22
12/12 to 14/12............ 5.0
1.52
14/12 to 16/12............ 6.0
1.83
16/12 to 18/12............ 7.0
2.13
18/12 to 20/12............ 7.5
2.29
21/12 to 21/12............ 8.0
2.44
QUESTIONS TO ASK LOCAL BUILDING OFFICIAL
This appliance must be installed per manufacturers’ instructions.
Installations must conform to appropriate local codes and applicable state
and federal requirements. Familiarity with these requirements before
installation is essential. Some important considerations to discuss with
local building officials include:
In the absence of local codes, installation should conform to National
Fuel Gas Code, ANSI Z223.1 / NFPA 54-Latest Edition in the USA or
National Fuel Gas Code, CAN/CGA-B149.1-Latest Edition in Canada.
Vertical
Wall
Lowest
Discharge
Opening
Vent
Termination
• The appliance must be secured to the floor (i.e. use (4) 1/4" x 2-3/4"
bolts and nuts or equivalent. NOTE: Not included) for securing appliance to the manufactured home floor.
• The appliance must be grounded to the chassis of the manufactured
home. Use a No. 8 or heavier copper wire at least 18” in length.
• The structural integrity of the manufactured home floor, walls, ceiling
and roof must be maintained.
• A manufactured (mobile) home installation must conform with the
Manufactured Home Construction and Safety Standard, Title 24 CFR,
Part 3280, or, when such a standard is not applicable, the Standard
for Manufactured Home Installations, ANSI / NCSBCS A225.1, or
standard for Gas equipped Recreational Vehicles and Mobile Housing,
CSA Z240.4.
1. Applicable codes (i.e. Uniform Mechanical Code, State or Regional
Gas Codes, National Fuel Gas Code)
2. Local amendments
3. Recognized certification agency: PFS Corporation
4. Is a permit required - cost?
5. In some states or municipalities, a licensed gas fitter or plumber may
be required to install this appliance. Check with your local building
official for requirements in your area (i.e. Is a license required for
installation of gas supply line)?
6. Maximum amount of gas pipe without a pressure test - type of test
required?
7. Are below grade penetrations of the gas line allowed?
8. Is concealed gas piping allowed?
9. Specific requirements of concealed fittings?
10.Is rigid pipe to appliance required?
11.Allowed piping materials?
12.Shut-off valve required within 4 feet of the firebox?
13.May the shut-off valve be concealed?
14.Rooms where the installation is not allowed?
2 FT
MIN.
2 FT MIN.
Figure 3
Horizontal Vent Termination Clearances
The horizontal vent termination must have a minimum of 3" (76 mm)
clearance to any overhead combustible projection of 2-1/2" (64 mm)
or less. See Figure 4. For projections exceeding 2-1/2" (64 mm), For
additional vent location restrictions refer to Figure 5.
Horizontal Vent Termination Clearances
Combustible Projection
2-1/2 inches or less in length
Combustible Projection
greater than 2-1/2 inches in length
Ventilated
Soffit
Unventilated
Soffit
18"
(457 mm)
12"
(305 mm)
3"
(76 mm)
Horizontal Termination Kit
T
Vent Termination Clearances
Vertical Vent Termination Clearances
These instructions should be used as a guideline and do not supersede
local codes in any way. Install vent according to local codes, these
instructions, the current National Fuel Gas Code (ANSI-Z223.1) in
the USA or the current standards of CAN/CGA-B149.1 in Canada.
3"
(76 mm)
1"
(25 mm)
Side Elevation View
NOTE: See vent manufacturer's instructions for recess allowances,
into exterior walls for the horizontal termination caps.
Figure 4
16
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
Exterior Horizontal Vent Termination Clearance Requirements
* See Item D in the Text Below.
Center Line
of Termination
Exterior Wall
Inside
Corner Detail
*18”
Horizontal
Termination
G
18”
V
Ventilated Soffit
A
Inside Corner
A
DETAIL D
= 9" in U.S.
= 12" in Canada
H
3 ft.
B
L
V
C
V
F
Fixed
Closed
Window
V
C
C
A
Operable
Window
V
C
V
B
X
D
A
V
3 ft.
J
B
M
B
B
X
V
I
A
X = Air Supply Inlet
E
V = Vent Terminal
K
= Area where Terminal is NOT permitted
Minimum Clearances
Canadian Installation *
US Installation **
A = Clearance above grade, veranda, porch, deck
or balcony.
12 inches (30 cm) *
12 inches (30 cm) **
B = Clearance to window or door that may be opened.
6 in. (15.2 cm) for appliances < 10,000 BTU/hr (3kW),
12 in. (30 cm) for appliances > 10,000 BTU/hr (3kW) and <
100,000 BTU/hr (30kW), 36 inches (91 cm) for appliances
> 100,000 BTU/hr (30kW)*
6 in. (15.2 cm) for appliances < 10,000 BTU/hr (3kW),
9 in. (23 cm) for appliances > 10,000 BTU/hr (3kW) and <
50,000 BTU/hr (15kW), 12 inches (30 cm) for appliances
> 50,000 BTU/hr (15kW)*
C = Clearance to permanently closed window
12 inches (305 mm) recommended to prevent window
condensation
9 inches (229 mm) recommended to prevent window
condensation
D = Vertical clearance to ventilated soffit located
above the terminal within a horizontal distance of
18 in. (458 mm) from the center line of the terminal
18 inches (458 mm)
18 inches (458 mm)
E = Clearance to unventilated soffit
12 inches (30 cm)
12 inches (30 cm)
F = Clearance to outside corner
5 inches (12.7 cm)
5 inches (12.7 cm)
G = Clearance to inside corner
6 in. (15 cm)
6 in. (15 cm)
H = Clearance to each inside of center line extended 3 feet (91 cm) within a height of 15 feet above the meter /
above meter / regulator assembly
regulator assembly *
3 feet (91 cm) within a height of 15 feet above the meter
/ regulator assembly **
I = Clearance to service regulator vent outlet
3 feet (91 cm) *
3 feet (91 cm) **
J = Clearance to non-mechanical air supply inlet
to building or the combustion air inlet to any other
appliance
6 in. (15.2 cm) for appliances < 10,000 BTU/hr (3kW), 12 6 in. (15.2 cm) for appliances < 10,000 BTU/hr (3kW), 9
in. (30 cm) for appliances > 10,000 BTU/hr (3kW) and < in. (23 cm) for appliances > 10,000 BTU/hr (3kW) and <
100,000 BTU/hr (30kW), 36 inches (91 cm) for appliances 50,000 BTU/hr (15kW), 12 inches (30 cm) for appliances
> 100,000 BTU/hr (30kW)*
> 50,000 BTU/hr (15kW)*
K = Clearance to mechanical air supply inlet
6 feet (1.8 meters) *
3 feet (91 cm) above, if within 10 feet (3 m) horizontally**
L = Clearance above paved sidewalk or paved
driveway located on public property
7 feet (2.13 m) ‡
7 feet (2.13 m) ‡
M = Clearance under veranda, porch, deck or
balcony
12 in. (30 cm) * ‡
12 in. (30 cm) ** ‡
* In accordance with the current CAN/CGA-B149.1 National Gas and B149.2 Propane Installation Code - Latest Editions.
** In accordance with the current ANSI Z223.1 / NFPA 54 National Fuel Codes - Latest Edition.
‡ A vent shall not terminate directly above a sidewalk or paved driveway which is located between two single family dwellings and serves both dwellings.
*‡ Only permitted if veranda, porch, deck or balcony is fully open on a minimum 2 sides beneath the floor.
Figure 5
17
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
The gas supply line should be plumbed from the fuel source to the
area where the appliance is to be installed per requirements outlined
in NFPA 54 - latest edition (USA) and CAN/CGA-B149.1 - latest edition (Canada).
Installation
WARNING
Failure to position the parts in accordance with these
diagrams or failure to use only parts specifically
approved with this appliance may result in property
damage or personal injury.
The proper gas line diameter must be used to run from the supply
regulator (at the gas company meter) to the appliance. Never use
galvanized or plastic pipe. Refer to Table 6 for suggested sizing of
the gas supply line if black iron pipe is being used.
The gas supply line should be connected to the appliance at Step 11.
Suggested Sizing of Black Iron Pipe
Schedule 40 - Pipe Supply Line
AVERTISSEMENT
Risque de dommages ou de blessures si les pièces
ne sont pas installées conformément à ces schémas
et ou si des pièces autres que celles spécifiquement
approuvées avec cet appareil sont utilisées.
Schedule 40 Pipe Length (Feet)
TYPICAL INSTALLATION SEQUENCE
See the page numbers references in the following steps for detailed
procedures.
The typical sequence of installation follows, however, each installation is
unique resulting in variations to those described.
Step 1.
Step 2.
Step 3.
Step 4.
Step 5.
Step 6.
Step 7.
Step 8.
Step 9.
Step 10.
Step 11.
Step 12.
Step 13.
Step 15.
Step 16.
Step 17.
Step 18.
Step 19.
(Page 18) Preparation - Plan and install gas line, venting system
and floor protection (if necessary).
(Page 18) Remove outer carton. Remove inner packages and
packing materials and set aside.
(Page 18) Remove stove from pallet and place into positioned
where unit is to be installed.
(Page 19) Remove front glass enclosure from stove and set
aside.
(Page 19) Remove the barrier.
(Page 19) Remove packaged materials from inside firebox and
set aside (log set, bag of embers and NG to LP conversion kit).
(Page 19) Remove cardboard packaging material from beneath
relief door and discard.
(Page 19) Install LP Conversion kit (if necessary). Install any
optional accessories (excluding firescreens).
(Page 20) Install lower access door.
(Page 20) Venting System Installation.
(Page 24) Connect gas supply line to the appliance. Purge Air.
(Page 24) Install log set, ember strip and embers.
(Page 26) Reinstall front glass enclosure.
(Page 26) Test all connections for leaks (factory and field).
(Page 27) Check appliance for proper operation.
(Page 27) Adjust burner to ensure proper flame appearance.
(Page 28) Install stove top, trivet and ash lip.
(Page 28) Attach Safety-in-Operation Warnings.
Detailed Installation Steps
Step 1: PREPARATION - Plan and install gas line and floor protection (if
necessary - see Floor Protection, Page 15).
18
Gas Supply Line (reference Figure 15 on Page 24) - Installing a gas
supply line from the fuel supply to the appliance involves numerous
considerations of materials, protection, sizing, locations, controls, pressure, sediment, and more. Certainly no one unfamiliar and unqualified
should attempt sizing or installing gas piping.
Schedule 40 Pipe
Inside Diameter (Inches)
Natural
Gas
Propane
Gas
0-10
1/2
3/8
10-40
1/2
1/2
40-100
1/2
1/2
100-150
3/4
1/2
150-200
3/4
1/2
Table 6
IMPORTANT NOTE: If propane is used, be aware that if the tank size is too
small (i.e. under 100-lbs, if this is the only gas appliance in the dwelling.
Ref. NPFA 58), there may be loss of pressure, resulting in insufficient fuel
delivery (which can result in sooting or other malfunctions). Any damage
resulting from an improper installation, such as this, is not covered under
the limited warranty.
Step 2: REMOVE PACKAGING - Remove the large outer carton.
Remove all the inner packages and packing materials and set aside.
To remove the ember strip package below the stove body, carefully
cut the 2 plastic ties using scissors.
Step 3: REMOVE FROM PALLET - A. Remove the trivet, then the cast
iron stove top by carefully lifting them up and off and setting them aside
(READ CAUTION BELOW).
CAUTION
The cast iron stove top is very heavy and may require a
minimum of two people to lift; one person on each side
(the CI1500 series cast top weighs ~20 pounds and the
CI2500 series cast top weighs ~40 pounds).
B. Remove stove body from pallet (READ CAUTION BELOW).
CAUTION
The stove body is very heavy. The use of a heavy duty
escalara (stair step hand truck) is recommended for
lifting the stove body.
Remove the screws and support plate which secure the stove legs to
the pallet. Lift stove off of the pallet and place it into position (where
unit is to be installed).
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
NOTE: Install Leg Leveling Bolts if Necessary: The four leg leveling
bolts (included in literature package), are provided for leveling the stove
if necessary. To install, thread the bolts into the existing holes in the
bottom of each leg. Turn the leveling bolts to adjust for correct height.
Step 4: REMOVE FRONT GLASS ENCLOSURE PANEL
Remove the front glass enclosure from stove per the instructions
on Page 30.
CAUTION: Label all wires prior to disconnection when servicing controls. Wiring errors can cause improper and dangerous
operation.
ATTENTION: Au moment de l'entretien des commandes,
étiquetez tous les fils avant de les débrancher. Des erreurs
de cáblage peuvent entraîner un fonctionnement inadéquat
et dangereux.
Step 5: REMOVE THE BARRIER - Remove the barrier from the stove
per the instructions on Page 32.
Step 6: REMOVE MATERIALS FROM FIREBOX - Remove the packaged materials from inside of the firebox and set aside (propane
conversion kit, log support cartons, log set and embers).
SIT Millivolt Wiring Diagram
If any of the original wire as supplied must be replaced,
it must be replaced with Type AWM105° C – 18 GA. wire.
Step 7: REMOVE CARDBOARD - Remove the cardboard packaging
material from beneath the relief door and discard (see Figure 6).
TH
TP
TH
TP
Remove Cardboard
Thermopile
* SWITCH
* ON/OFF Switch, Optional
Thermostat Remote
Control Receiver
RELIEF DOOR
Figure 7
Figure 6
OPTIONAL WALL THERMOSTAT
Step 8: INSTALL LP CONVERSION KIT (IF NECESSARY) AND
OPTIONAL ACCESSORIES
Install the LP conversion kit and optional accessories per instructions
provided with the kits (do not install an optional firescreen or brick
liner kit at this point).
A. Optional accessories include a wall thermostat, blower kit, brick liner
kit, warming shelves and a standard or deluxe remote control kits.
B. If a wall-mounted thermostat is selected, mount it in a convenient
location on a wall near the stove. If the warming shelves are being
installed, see Page 44.
C. Wire the thermostat within the millivolt control circuit using a maximum
of 25 feet of 18 gage, 2 conductor wire. Caution: Do not connect the
optional wall thermostat, gas control valve or control wiring system
of the unit to a 120 volt power supply (residential line voltage).
If an optional wall thermostat is to be installed, install the thermostat
per the manufacturers instructions (provided with the thermostat).
Failure to follow manufacturers instructions could result in a malfunction. Pay special attention to the thermostat location requirements.
If the location requirements are not adhered to the appliance, erratic
operation or failure may occur.
Do not mount the thermostat where it may be affected by:
• Radiant heat from this appliance, fireplaces, sun or other heat
sources.
• Drafts or dead spots behind doors or in corners.
• Hot or cold air from ducts.
The gas valve is set in place and pre-wired at the factory on both models
(see Figure 7).
19
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
Wiring - Optional Forced Air Blower Kit:
Step 9: INSTALL LOWER ACCESS DOOR
BK-CI (see Figure 8 for wiring diagram) - (An optional field-provided
outletbox/J-Box may also be used). Install the blower kit according to
the installation instructions provided with the kit.
Install the lower access door by inserting the tabs on the door sides
into the corresponding holes on the brackets on the stove bottom
(see Figure 9).
WARNING
The power cord must be plugged directly into a properly
grounded three-prong 120 volt, 60 hz wall receptacle. Do
not cut or remove the grounding prong from this plug.
Do not route power cord under or in front of appliance.
CAUTION: Label all wires prior to disconnection when servicing controls. Wiring errors can cause improper and dangerous
operation.
ATTENTION: Au moment de l'entretien des commandes,
étiquetez tous les fils avant de les débrancher. Des erreurs
de cáblage peuvent entraîner un fonctionnement inadéquat
et dangereux.
Lower Access
Door
The lower access door hinges open to access Valve Controls
Figure 9
Blower Wiring
Diagram
Power Cord
Step 10: VENTING SYSTEM INSTALLATION
INSTALL VENTING COMPONENTS PER VENT MANUFACTURERS
INSTRUCTIONS
Blower
Assembly
(Shown
Rotated 90
Degrees CCW)
Blower
Mounting
Bracket
The vent system may not service multiple appliances.
CAUTION: Under no circumstances should these appliances be
vented to other rooms or buildings. These appliances must only
be vented to the outside. Vent terminations shall not be recessed
into a wall or siding.
IMPORTANT: Do not exceed the maximum horizontal run allowed
(see Figures 10 and 11).
Support Brackets - Install vent support brackets as specified in the
vent manufacturers instructions and the National Gas Fuel Code, USA
- NFPA 54 / ANSI Z223.1, Support of Gas Vents. Gas vents shall be
supported and spaced in accordance with their listings and the (vent)
manufacturer instructions.
Black
Black
White
White
Figure 8
Fan Disc
Black
Rheostat
General Information: These instructions should be used as a guideline
and do not supersede local codes in any way. Install vent according
to local codes, these instructions, the current National Fuel Gas Code
(NFPA 54 / ANSI-Z223.1) in the USA or the current standards of CAN/
CGA-B149.1 in Canada.
These stoves are designed, tested and listed for operation and installation
with, and only with, "Secure Vent® " or "Simpson Dura Vent" brand
Components (co-axial DV pipe with 4" inner and 6-5/8" outer diameter).
These approved vent system components are labeled for identification. DO
NOT use any other manufacturer's vent components with these appliances.
20
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
Horizontal Termination
Vertical Termination
The vent must rise vertically, a minimum of 24" (610 mm) off
the top of the appliance for Natural Gas and 36" for Propane Gas
before the first elbow.
A vertical vent system must terminate no less than 8 feet ( 2.44 meters)
and no more than 40 feet / 12 meters (above the appliance flue collar).
See Figure 11.
The horizontal run may extend up to 20 feet ( 6 meters) and include
a vertical rise of up to 40 feet (12 meters) - see Figure 10. Horizontal
termination must meet the criteria shown in Figures 4 and 5.
A vertically terminated vent system must also conform to the following
criteria:
• Approved vent systems must terminate above and including the
heavy line in Figure 10.
• Two 45 degree elbows may be substituted for each single 90 degree
elbow.
• With a rise between 2 feet to 5 feet, one 90 degree or two 45 degree
elbows may be used.
Vent must rise a minimum of 2 feet before an offset is used.
Termination height must conform to roof clearance as specified in Figure 3.
40
39
39
38
38
37
36
37
36
35
34
35
34
Measure from the appliance flue collar to the top of the vent pipe
32
31
May use up to three 90
degree elbows
30
29
28
27
26
Vertical Run (in feet)
Vertical Run (in feet)
Two 45 degree elbows may be substituted for one 90 degree elbow. No
more than six 45 degree elbows may be used.
40
33
Measure from the appliance flue collar to the top of the vent pipe
No more than three 90 degree elbows may be used.
25
24
23
22
21
20
19
18
17
16
15
14
13
12
11
33
32
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
15
Unacceptable
Venting
Configuration
14
13
12
11
10
9
10
9
8
8
7
7
6
5
6
5
One 90
degree
elbow
4
3
2
Unacceptable
Venting
Configuration
1
0
1
Figure 10
Vertical Terminations Must
be in this area
2
3
4
5
6
7
8
4
3
2
1
0
1
9 10 11 12 13 14 15 16 17 18 19 20
Horizontal Run (in feet)
Figure 11
2
3
4
5
6
7
8
9 10 11 12 13 14 15 16 17 18 19 20
Horizontal Run (in feet)
21
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
Installing Support Brackets
Install support brackets per vent manufacturers instructions.
Vertical Vent Installation
Support Bracket Placement Diagram
Support
Brackets
Wall
Stud
The chimney conversion should not be applied to the portion of the vent
system that is in the room of the appliance. Use only Co-Axial directvent pipe (4” inner pipe, 6-5/8” outer pipe as listed on Page 23) from the
appliance to the retro-connector into converted flue system. Adhere to all
specifications outlined in this manual regarding clearances to combustibles,
vertical and horizontal vent length minimums and maximums, etc. Read
all instructions in this manual and provided by vent manufacturer with kit
carefully before starting the installation. Failure to follow the instructions
may create a fire or other safety hazard, and will void the warranty. The
following Vent System components may be safely used with this appliance.
Chimney DV Liner Kits
Model
Placement:
Horizontal Runs - Requires a
support bracket every 5 feet
(152 cm).
1 inch
minimum
Vertical Runs - Requires 8 feet
support brackets every 8
feet (244 cm) above the
stove vent outlet..
Brand: Secure Vent / Description
SV4MCK
Masonry Chimney Conversion Kit –Vertical term. Cap, cap
Adaptor, masonry cover, black Adaptor (to flex), 2 gear clamps
SV4CCK1
Factory Built Chimney Conversion Kit – for 6” I.D., 1” insulation.
SV4CCK2
Factory Built Chimney Conversion Kit – for 7” I.D., 1” insulation; 8” I.D., 1” insulation; 6” I.D., 2” insulation
SV4CCK3
Factory Built Chimney Conversion Kit – for 10” I.D., 1” insulation; 7” I.D., 2” insulation; 8” I.D., 2” insulation
Model
Brand: SIMPSON DURA-VENT / Description
934
Masonry Chimney Conversion Kit
931
Factory Built Chimney Conversion Kit A – for 6” I.D.;
932
Factory Built Chimney Conversion Kit B – for 6”, 7” & 8” I.D.
933
Factory Built Chimney Conversion Kit C – for 7” & 8” I.D.
Table 7
Figure 12
Select Venting System - Horizontal Or Vertical
The following sections describe vertical (roof) and horizontal (exterior
wall) vent applications. Refer to the section relating to your installation.
A list of approved venting components is shown on Pages 22 and 23.
Horizontal Vent Installation
Support Bracket Placement Diagram
Support
Building Brackets
Support
Framing
Horizontal / Inclined Run
(¹⁄₄" Rise per Foot of Horizontal Run in the
Direction away from the Stove)
Vertical
Termination
Shown
Elbow
Vent Sections
Ceiling
Vertical
Rise
Firestop/Spacer
Support Bracket Spacing
Every 5 ft (1.52 m)
Horizontal
Exterior
Wall
Combustion
Air
See figure for
vertical vent
section support.
Exhaust
Figure 13
Direct-Vent Retrofit Of Existing Chimney System
An existing Class-A (wood-burning) Metal Chimney or Masonry Chimney can be converted to a direct-vent system. Use one of the following
chimney conversion kits listed below. Have the existing chimney system
inspected by a professional prior to the conversion.
Figure 14
22
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
Direct-Vent System Components
The following "Secure Vent® " or "Simpson Dura-Vent" brand Direct-Vent components may be safely used with these appliances.
IMPORTANT NOTE: Seal the first section of pipe to the stove collar using mill-pac black, high temperature sealant.
Model #
Model #
SIMPSON DURA-VENT Description
N/A
N/A
970
Basic Horizontal Term. Kit (90 Deg. Black Elbow, Wall Thimble
Cover, Horizontal Square Term. Cap)
N/A
N/A
971
Horizontal Term. Kit A (90 Deg. Black Elbow, Wall Thimble Cover,
Horizontal Square Term. Cap, adj. 24” black pipe, 11-14 5/8” adj.
black pipe)
SV4FK
Vertical Flat Roof Term. Kit (w/flashing, storm collar, vertical Term. Cap)
973
Vertical Termination Kit (990B, 940, 984)
SV4FAK
Vertical pitched Roof Kit, 1/12-7/12 (with adjustable roof flashing, storm
collar, vertical termination cap)
978
Vertical Pitched Roof Kit, 0/12–6/12 (with adjustable flashing,
storm collar, low profile term. Cap)
SV4FBK
Vertical pitched Roof Kit, 8/12-12/12 (with adjustable roof flashing, storm
collar, vertical termination cap)
N/A
N/A
SV4L6
6” Pipe Length (Galvanized)
908
6” Pipe Length (Galvanized)
SV4LB6
6” Pipe Length (Black)
908B
6” Pipe Length (Black)
N/A
SECURE VENT - Description
N/A
907B
9” Pipe Length ( Black)
SV4L12
12” Pipe Length (Galvanized)
906
12” Pipe Length (Galvanized)
SV4LB12
12” Pipe Length (Black)
906B
12” Pipe Length (Black)
SV4L24
24” Pipe Length (Galvanized)
904
24” Pipe Length (Galvanized)
SV4LB24
24” Pipe Length (Black)
904B
24” Pipe Length (Black)
SV4L36
36” Pipe Length (Galvanized)
903
36” Pipe Length (Galvanized)
SV4LB36
36” Pipe Length (Black)
903B
36” Pipe Length (Black)
SV4L48
48” Pipe Length (Galvanized)
902
48” Pipe Length (Galvanized)
SV4LB48
48” Pipe Length (Black)
902B
48” Pipe Length (Black)
SV4LA
6” Adj. Pipe Length, (Galvanized)
908
6” Adj. Pipe Length, (Galvanized)
SV4LBA
6” Adj. Pipe Length (Black)
N/A
N/A
SV4LA12
12” Adj. Pipe Length, (Galvanized)
911
11”-14 5/8” Adj. Pipe Length (Galvanized)
SV4LBA12
12” Adj. Pipe Length, (Black)
911B
11”-14 5/8” Adj. Pipe Length (Black)
SV4E45
45 Deg. Elbow, Swivel (Galvanized)
945G
45 Deg. Elbow, Swivel (Galvanized)
SV4EB45
45 Deg. Elbow, Swivel (Black)
945BG
45 Deg. Elbow, Swivel (Black)
SV4E90
90 Deg. Elbow, Swivel (Galvanized)
990G
90 Deg. Elbow, Swivel (Galvanized)
SV4EB90
90 Deg. Elbow, Swivel (Black)
990BG
90 Deg. Elbow, Swivel (Black)
SV4E90
90 Deg. Elbow (Galvanized)
990
90 Deg. Elbow (Galvanized)
SV4EB90
90 Deg. Elbow (Black).
990B
90 Deg. Elbow (Black)
SV4CHC-1
N/A
SV4CGV
Horizontal Standard Term. Cap
984
Horizontal Standard Term. Cap
N/A
991
Vertical High Wind Term. Cap
Vertical Termination Cap
N/A
N/A
SV4STC36
Snorkel Termination Cap 36”
981
Snorkel Termination Cap 36”
SV4STC14
Snorkel Termination Cap 14”
982
Snorkel Termination Cap 14”
SV4VS
Vinyl Shield Protector
950
Vinyl Siding Standoff
SV4SF
Round Ceiling Support / Wall Thimble Cover
940
Round Ceiling Support / Wall Thimble Cover
Cathedral Ceiling Support Box, decorative square
941
Cathedral Ceiling Support Box
SV4CSB
SV4PF
Black Plate, Decorative, Square
N/A
N/A
SV4SU
Universal Support
942
Round Ceiling Support Box/Wall Thimble
SV4FC
Storm Collar
953
Storm Collar
Wall Radiation Shield
N/A
N/A
SV4BF
Firestop
963
Firestop Spacer
SV4F
Flashing, Flat Roof (storm collar included)
N/A
N/A
SV4FA
Flashing, Adjustable roof 1/12-7/12 (storm collar included)
943
Flashing 0/12-6/12
SV4FB
Flashing, Adjustable 8/12-12/12 (storm collar included)
943S
Flashing 7/12-12/12
SV4BM
Wall Band (Strap)
988
Wall Strap
SV4RSM
Table 8
NOTE: Snorkel Caps: These are elongate vent termination caps, which incorporate the principles of natural draft into a horizontal installation.
Two styles are common, 14” and 36” (Cap height). They enhance draft and relieve back-pressure by creating natural draft in the snorkel.
23
When first lighting the appliance, it will take a few minutes for the line
to purge air from the appliance. Once purging is complete, the pilot
and burner will light and operate as indicated in the instruction manual.
Subsequent lightings of the appliance will not require such purging. Inspect
the pilot flame (remove logs, if necessary, handling carefully).
Step 11. Connecting Gas Line
Gas Flex Line Connector
Gas
Valve
3/8" NPT x 1/2" x 3/8" Flare
Flare Fitting Shut-off Valve
3/8" Flex Tubing
1/2" x 3/8"
Reducer
3/8" Nipple
Gas
Stub
3/8" Union
3/8" Close
Nipple
3/8" Shut-off Valve
Gas Solid Line Connector
Figure
16
3"
Min
*Sediment
Trap
Step 12. Installing Logs and Glowing Embers
NOTE: The gas supply line must be installed in accordance with building codes by
a qualified installer approved and/or licensed as required by the locality. In the
Commonwealth of Massachusetts, installation must be performed by a licensed
plumber or gas fitter.
The packaged log set and bag of glowing embers are located within
the firebox of the stove.
*A Sediment Trap is recommended to prevent moisture and debris in gas line from
damaging the valve.
Installation Instructions:
Figure 15 - GAS CONNECTION
WARNING
Make gas line connections. All codes require a shut-off valve mounted
in the supply line. Figure 15 illustrates two methods for connecting
the gas supply. The flex-line method is acceptable in the U.S., however,
Canadian requirements vary depending on locality. Installation must be
in compliance with local codes.
These appliances are equipped with a gas flex line for use (where permitted) in connecting the unit to the gas line. A gas flex line is provided
to aid in attaching the direct-vent appliance to the gas supply. The gas
flex line can only be used where local codes permit. See Figure 15 for
flex line description. The flex line is rated for both natural and propane
gas. A manual shut off valve is also provided with the flex line. The gas
control valve is located in the lower control compartment. To access the
valve, open the lower access door. The millivolt control valve has a 3/8"
(10 mm) NPT thread inlet port fitting.
If logs are not installed according to the directions shown
here, flame impingement and improper combustion could
occur and result in soot and/or excessive production of
carbon monoxide (CO), a colorless, odorless, toxic gas.
Carefully install the ember strip and seven-piece log set into the
firebox as shown in these instructions. All logs should fit onto corresponding pins and/or log stoppers. This will ensure a proper flame
and safe combustion.
1. Carefully place the ember strip as shown in Figure 17. Ensure
that it is pushed all the way back in position (toward the sub-floor
front flange).
AIR PURGING PROCEDURES MUST PERFORMED BY A QUALIFIED
TECHNICIAN ONLY.
Purging Air from Supply Line
a. Turn gas supply line valve off.
b. Loosen setscrew at inlet pressure tap on upper right of control valve
(see Figure 27 on Page 27).
c. Turn gas supply line valve on.
d. When gas flows, turn supply valve off.
e. Close the inlet pressure tap.
Purging Air from Appliance
Purge air from appliance by holding gas control valve down in the pilot
position until pilot will light (see Figure 16). DO NOT LIGHT A MATCH
IF YOU SMELL GAS. Light a match then allow gas flow to pilot. If the
Match “blows”, there is air in the line (purge line). If the flame is straight
and tall, there is no gas pressure.
Rear Log Stoppers
Ember
Strip
Figure 17
24
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
NOTE: If an optional Brick Liner Kit was purchased, install it now, per instructions provided in kit
5. Install the right front log onto the corresponding burner pin and
sub-floor right tab as shown in Figure 21.
2. Place the largest log onto the rear log stoppers (see Figure 17).
Ensure that the grooves on the bottom of the log aligns onto the
corresponding places on the rear log stoppers. Push the log back so
that it is against the back of the rear log stoppers (see Figure 18).
Rear
Log
Right Front Log
Figure 21
Figure 18
3. Place the left front log onto the corresponding burner pin and
sub-floor left tab as shown in Figure 19.
6. Install the left top twig onto the corresponding pin on the rear
log and align it with the indentation on the front left log as shown
in Figure 22.
Left Top Twig
Figure 22
Figure 19
Left Front Log
7. Install the center top twig onto the corresponding pin on the rear
log and align it with the indentation on front left log as shown in
Figure 23.
4. Place the center log piece over the corresponding pins next to the
front left log as shown in Figure 20.
Center
Top Twig
Center
Log
Piece
Figure 20
Figure 23
25
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
8. Install the front right twig onto the corresponding pin on the right
front log. Align the twig with the indentation on the front right log as
shown in Figure 24.
Right
Front Twig
DO NOT PLACE EMBERS ON TOP OF THE BURNER SLOTS.
Figure 26
VERIFY THAT THE GAS LINE HAS BEEN PURGED OF AIR (SEE STEP 11).
Step 13. re-install FRONT GLASS ENCLOSURE PANEL
(Reverse instructions on Step 4)
Figure 24
9. Place the glowing embers on the burner as shown in Figures 25
and 26.
One package of ember material has been included with this log set
You will not need to use the entire bag.
IMPORTANT: The quantity and placement of the ember material can
affect stove performance therefore it is very important that it be placed
as shown in Figures 25 and 26.
Retrieve the front glass enclosure panel. Visually inspect the gasket
on the backside of the frame. Gasket surface must be clean, free of
irregularities and seated firmly.
With the stove top off, position the glass front enclosure panel into
the front opening with the gasket facing the relief door (reference
Figure 39 on Page 30). Let the bottom of the door frame gently
slide down, then hook the top flange of the glass frame over the top
of the firebox frame.
Fasten the two latches located beneath the firebox floor to the glass
frame vee-flange. Close both the latches securely.
a. Unpackage and divide the fine ember material (mineral wool) into
dime-sized fluffy pieces.
Step 14. RE-INSTALL THE BARRIER
b. Distribute the pieces over the top of the front burner ports avoiding
covering the slots (see Figure 26) and filling the area in front of the
forward logs.
Push the barrier down the backside of the front casting, seating it
between the front casting and barrier retainers (reference Figure 40
on Page 32).
Step 15. TEST ALL CONNECTIONS FOR LEAKS (FACTORY AND
FIELD).
WARNING
Never use an open flame to check for leaks.
Embers
Figure 25
Turn on gas supply and test for gas leaks using a gas leak test solution (also
referred to as bubble leak solution). NOTE: Using a soapy water solution
(50% dish soap, 50% water) is an effective leak test solution but it is not
recommended, because the soap residue that is left on the pipes/fittings can
result in corrosion over time.
A. Light the appliance (refer to the lighting instructions on Page 34).
B. Brush all joints and connections with the gas leak test solution to check for
leaks. If bubbles are formed, or gas odor is detected, turn the gas control
knob (off/pilot/on) to the “OFF” position. Either tighten or refasten the
leaking connection, then retest as described above.
C. When the gas lines are tested and leak free be sure to rinse off the
leak testing solution,
D. Turn on burner then observe the individual tongues of flame on the burner.
Make sure all ports are open and producing flame evenly across the
burner. If any ports are blocked, or partially blocked, clean out the ports.
26
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
Step 16. Checking Appliance Operation
With gas line installed run initial system checkout before closing up
the front of the unit. Follow the pilot lighting instructions on Page
34 (or pull out the instruction label located in a holder on rear shield
of stove) . For piezo igniter location see Figure 27.
SIT Millivolt Gas Valve Controls
HI / LO Knob
Variable Flame Height Adjustment
Inlet
Pressure
Port
Manifold Pressure Port
Step 17. Burner Adjustments
Flame Appearance and Sooting
Proper flame appearance is a matter of taste. Generally, most people
prefer the warm glow of a yellow to orange flame.
Appliances operated with air shutter openings that are too large will
exhibit flames that are blue and transparent. These weak, blue and
transparent flames are termed anemic. If the air shutter opening is too
small sooting may develop.
IN
OUT
TPTH
TP
HI
TH
LO W
OF
it
PIL O T
ON
F
P IL
OT
Main Gas
Control Knob
Figure 27
Piezo Igniter
Burner
On/Off
Switch
Top View
Figure 30 - Burner Flame Appearance
Front
Piezo Igniter
Figure 28
SIT Millivolt Appliance Checkout
The pilot flame should be steady, not lifting or floating. Flame should
be blue in color with traces of orange at the outer edge. The top 3/8"
(10 mm) at the pilot generator (thermopile) and the top 1/8" minimum
(tip) of the quick drop out thermocouple should be engulfed in the
pilot flame.
The flame should project 1" (25 mm) beyond the hood at all three
ports (Figure 29).
Sooting is indicated by black puffs developing at the tips of very long
orange flames. Sooting results in black deposits forming on the logs,
appliance inside surfaces and on exterior surfaces adjacent to the
vent termination. Sooting is caused by incomplete combustion in the
flames and lack of combustion air entering the air shutter opening. To
achieve a warm yellow to orange flame that does not soot, the shutter
opening must be adjusted between these two extremes.
No smoke or soot should be present. Reposition the logs if flames
impinge on any of them. If the logs are properly positioned and sooting conditions exist, the air shutter opening on the main burner tube
should be adjusted. Normally, the more offsets in the vent system,
the greater the need for the air shutter to be opened further.
Replace logs if removed for pilot inspection.
To light the burner, rotate the gas valve control knob counterclockwise
to the “ON” position then turn “ON” the ON/OFF rocker switch.
Hood
MILLIVOLT
IMPORTANT
Ensure that the front glass panel is in place and
sealed during adjustment.
Igniter Rod
WARNING
Thermocouple
Air shutter adjustment should only be performed by
a qualified professional service technician.
3/8" Min.
(9 mm)
Pilot
Nozzels
Thermopile
CAUTION
The adjustment rod and nearby appliance surfaces
are hot. Exercise caution to avoid injury while
adjusting flame appearance.
Figure 29 - Proper Pilot Flame Appearance
27
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
Burner Adjustment
Step 18. INSTALL STOVE TOP, TRIVET AND ASH LIP
Initially, always position the air shutter to the factory setting as shown
in Figure 31 (adjustment rod is located in the lower control area). This
can be done by moving the adjustment rod up or down accordingly.
Allow the burner to operate for at least 15 minutes. Observe the flame
continuously. If it appears weak or sooty as previously described,
adjust the air shutter to a more open position until the desired flame
appearance is achieved.
A. Place the cast iron top into position on the stove top (See Figure 32).
Place the trivet into the recess on the cast iron top (See Figure 32).
Flame adjustments can be made quickly and accurately to taste without
the need of disassembling the appliance and waiting for 30 minutes after
each adjustment.
Burner Air Shutter Adjustment
CAUTION
The cast iron stove top is very heavy and may require
a minimum of two people to lift; one person on each
side (the CI1500 series cast top weighs ~20 pounds
and the CI2500 series cast top weighs ~40 pounds).
Trivet
Stove Cast Iron Top
Adjusting Set Screw
Trivet
Adjustment Rod Up
(1/8" Open Position)
Burner Tube
Air Shutter
Adjustment Rod Down
(full open position)
Main Burner Factory Air Shutter
Opening Setting - Inches (millimeter)
Model
Natural
Gas
Propane
Gas
CI1500DVF
5/16"
(7.93 mm)
5/8"
(15.9 mm)
CI2500DVF
1/2"
(12.7 mm)
5/8"
(15.9 mm)
Figure 32
B. Locate the ash lip from packaging (Step 2). Remove the 2 bolts from
the tapped holes in the ash lip. Align the ash lip below the firebox
as shown in Figure 33 (the tapped holes in ash lip should align with
corresponding slots below firebox). Reinstall the 2 bolts that were
removed from the ash lip (finger tight only. If a tool is used, be careful
not to overtighten).
Figure 31
Air Shutter Adjustment Guidelines:
If the burner flame appearance differs greatly from what is shown
on Page 27 (see Figure 30), some adjustment from standard for the
air shutter gap may be necessary (to compensate for variables in the
installation and fuel such as, BTU value / composition, gas pressure,
specific gravity of gas, altitude, etc.).
The following chart is provided to aid you in achieving the correct air
shutter adjustment for your installation.
Ash Lip
Figure 33
Air Shutter Adjustment Guidelines:
Amount of
Primary Air
Flame Color
Air Shutter
Adjustment
If air shutter is
closed too far
Flame will
be yellow
Air shutter gap should be
increased
If air shutter is open
too far
Flame will
be blue
Air shutter gap should be
decreased
Table 9
28
When satisfied that the appliance operates properly, proceed to finish
the installation. Leave the control knob in the ON position and the on/
off switch in the OFF position.
Step 19. INSTALLER INSTRUCTIONS - ATTACH
SAFETY-IN-OPERATION WARNING LABELS
It is required that the set of safety instruction labels that have been
furnished with the appliance be affixed to the operation and control
points of the appliance per the instructions on Page 7. It is the
installers responsibility to ensure these warnings are properly
affixed during installation. These warning labels are a critical
step in informing consumers of safe operation of this appliance.
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
TPTH
TP
HI
TH
LO W
OF
it
ON
F
P IL
If your millivolt appliance is equipped with an optional wall thermostat kit
or remote control kit and the pilot is lit, the appliance main burner may be
turned on and off with the wall thermostat or remote control.
OT
Main Gas
Control Knob
Always keep the appliance area clear and free from combustible materials,
gasoline and other flammable liquids.
Remember, Millivolt appliances have a continuous burning pilot flame.
Exercise caution when using products with combustible vapors.
PIL O T
In lieu of remote or remote wall thermostat operation, the appliance must
be operated directly through the on/off rocker switch located on the upper
right side of the rear shield. See Figure 34.
Inlet
Pressure
Port
Manifold Pressure Port
OUT
Appliance operation may be controlled through a remotely located optional
wall thermostat or remote control.
HI / LO Knob
Variable Flame Height Adjustment
IN
OPERATION AND CARE OF YOUR APPLIANCE
Piezo Igniter
Figure 36 - SIT Millivolt Gas Valve Controls
GAS CONTROLS
Lighting Millivolt Appliances
Burner
On /Off
Switch
Front
Top View
To light millivolt appliances refer to the detailed lighting instructions found
on Page 34 (English) and Page 35 (French). Millivolt appliance lighting
instructions may also be found on the pull-out lighting instruction labels
attached to the rear stove shield. Refer to Figure 36 for the location of
the piezo igniter.
Piezo Igniter
Millivolt appliances are fitted with a burner ON/OFF Rocker Switch, located
at the right the rear stove shield as shown in Figure 34. Once the pilot
is lit, the ON/OFF rocker switch will control the appliance ON/OFF operation.
To operate: Toggle the switch between its ON and OFF positions.
Figure 34 - Burner On/Off Switch
VARIABLE FLAME HEIGHT ADJUSTMENT
CONTROL COMPARTMENT ACCESS
The gas controls can be found behind the lower access door. To access,
pull the door open (see Figure 35).
All Millivolt appliances are equipped with a variable gas control valve.
Flame height for these models may be adjusted through a range between
fixed low and high settings by rotating the HI/LO knob on the valve (see
Figure 36), alternately, while the appliance is in operation. Adjust the
flame height as desired after lighting the appliance by rotating the variable adjustment control (HI/LO) knob located on the front of the valve.
BURN-IN PERIOD
During the first few burns of this appliance there will be some odor due
to the “burn-in” of paints and lubricants (curing of the high temperature
paint and burning off of lubricants used in the manufacturing process).
Depending on your use, the burn-in period may take a few hours or a few
days. The dwelling should be well ventilated during these initial burns.
Pull open lower
door to access
Valve Controls
IMPORTANT
Lower Access Door
Keep your house well ventilated during the curing
process. The odor and haze emitted by the curing
process can be quite noticeable and may set off a
smoke detector.
If the optional Blower Kit (see Page 42 for ordering information) is
installed, do not turn on a blower during the Burn-In period. Do not
place anything on the stove surface until the paint is completely cured.
Figure 35 - Lower Access Door
Millivolt appliances will be fitted with the gas control valve shown in
Figure 36. Familiarize yourself with the gas control valve that your
appliance uses.
(Serefina™ Models with Black Paint) Do not attempt to repaint the stove
until the paint is completely cured. If the surface later becomes stained
or marred, it may be lightly sanded and touched up with spray paint (See
Small Area Paint Touch-Up, Page 31). Paint is available at your local IHP
dealer. Never attempt to paint a hot stove.
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
29
FRONT GLASS ENCLOSURE PANEL, REMOVAL AND INSTALLATION
B. Reach under the bottom front of the front glass enclosure and pull
it forward as shown in Figure 38.
WARNING
• Do not attempt to substitute the materials used on
these doors, or replace cracked or broken glass.
• Handle this glass with extreme care! Glass is
susceptible to damage – Do not scratch or handle
roughly while reinstalling the glass door frame.
• The glass door(s) of this appliance must only be
replaced as a complete unit as provided by the
manufacturer. Do not attempt to replace broken,
cracked or chipped glass separately.
• Do not attempt to touch the front enclosure glass
with your hands while the appliance is in use.
• Do not use abrasive cleaners. Never clean the
glass when it is hot.
• DO NOT abuse glass door by striking or slamming
shut.
Figure 38
C. Lift glass assembly up and out and carefully set aside in a safe
place (see Figure 39).
CAUTION
Do not operate the appliance with glass removed,
cracked or broken.
ATTENTION
Ne pas utiliser l'appareil si le panneau frontal en
verre n'est pas en place, est craqué ou brisé.
Only doors certified with the appliance shall be used.
Figure 39
Seules des portes certifiées pour cet appareil doivent être
utilisées.
Do not remove glass door while the appliance is hot.
Remove the front glass enclosure from stove as follows:
A. Locate and open the 2 latches below the stove body (See Figure 37).
Figure 37
To install the front glass enclosure panel, proceed as follows:
1. Retrieve the glass door frame. Visually inspect the gasket on the
backside of the panel. The gasket surface must be clean, free of
irregularities and seated firmly.
2. With the stove top off, position the glass front enclosure panel
into the front opening with the gasket facing the relief door (see
Figure 39). Let the bottom of the door frame gently slide down,
then hook the top flange of the glass frame over the top of the
firebox frame.
3. Fasten the two latches located beneath the firebox bottom to the
glass frame vee-flange. Close both the latches securely.
4. Reinstall the cast iron stove top (read “Caution,” on this page).
5. Reinstall Trivet.
Open both Latches as shown.
30
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
MAINTENANCE
WARNING
• DO NOT use abrasive cleaners on glass.
• DO NOT clean glass when hot.
WARNING
Turn off gas and electrical power to the fireplace
and allow it to cool before cleaning or servicing
the appliance.
CAUTION: Wear gloves and safety glasses for protection while
doing required maintenance.
WARNING
Do not attempt to touch the front enclosure glass
with your hands while the stove is in use.
SMALL AREA PAINT TOUCH-UP
Verify proper operation after servicing.
Models with Black Painted Finish
S'assurer que l'appareil fonctionne adéquatement une fois
l'entretien terminé.
The appliance and venting system should be thoroughly inspected before
initial use and at least annually by a qualified service technician. However,
more frequent periodic inspections and cleanings should be performed by
the homeowner. Homeowner must contact a qualified service technician
at once if any abnormal condition is observed.
IMPORTANT NOTE: Prior to the first use of the fireplace and each
burn season and periodically during the burn season, inspect the
horizontal termination for debris such as bird nests, leaves, paper
or branches. Remove any items from the surfaces of the termination
prior to use. Also be aware of shrubs and plantings that may encroach
on the termination.
The stove body is painted with a quality high-temperature stove paint.
Only use factory supplied Stove Paint for touch-ups (H8159).
Using one small piece of 320 grit sand paper and lightly sand the blemish so that the edges are “feathered” or smooth to the touch between
the painted and bare surfaces. Do not let the sand paper gum up with
paint, as this will cause scratches on the metal surface. If there are any
scratches, use 600 grit sandpaper instead. Mask off surfaces you do not
want painted. Paint lightly over the bare surface first as this will act as an
under-coat. Then paint over a larger area in smooth even strokes to blend.
See Burn-In Period on Page 29 for information on curing the paint.
SMALL AREA TOUCH-UP PAINT
Models with Enamel Finish
Refer to the maintenance schedule on Page 37 for maintenance tasks,
procedures, periodicity and by whom they should be performed. Always
verify proper operation of the appliance after servicing.
If the enamel finish on your stove becomes chipped, it can be touched
up using the enamel touch-up paint. Follow instructions on tube for
applying. See Page 40 for ordering information.
Always turn off gas to the pilot (millivolt appliances) before cleaning.
Before re-lighting, refer to the lighting instructions in this manual. Instructions are also found on a pull-out panel located on the rear stove shield.
NOTE: When enamel is heated to high temperatures it is subject to crazing
(a very fine and random network of hairline cracks on the surface of the
porcelain). Crazing is a normal occurrence when enamel is exposed to
high temperatures. Your enamel finish will not be harmed nor will the
function of the stove be impaired.
Keep lower control compartment clean by vacuuming or brushing at least
twice a year. More frequent cleaning may be required due to excessive
lint from carpeting, bedding materials, etc. It is important that control
compartments, burners and circulating air passageways of the appliance
be kept clean.
Glass Cleaning
NOTE: Clean glass after first two weeks of operation (after Burn-In
period is over).
The viewing glass should be cleaned periodically to remove any build-up
caused from the following:
Models with Porcelain Enamel Finish
Crazing of Porcelain Enamel: Porcelain enamel, when heated to high
temperatures, is subject to crazing (a very fine and random network of
hairline cracks on the surface of the porcelain). Crazing is a normal
occurrence when enamel is exposed to high temperatures. Your enamel
finish will not be harmed nor will the function of the stove be impaired.
Repairing Chips: If the enamel finish on your stove becomes chipped, it
can be touched up using enamel touch-up paint. For ordering information, see Page 40.
• During start-up, it is normal for condensation to form on the inside
of the glass (this condensation and fog will usually disappear in a few
minutes). This can cause lint, dust and other airborne particles to
cling to the glass surface.
• Initial curing of the high temperature paint and burning off of lubricants
used in the manufacturing process may result in a film on the glass.
• A white coating may form on the glass as a result of impurities and
minerals in the fuel.
Cleaning Enamel Surfaces: To remove build-up of dust, dirt or crud
from the enamel surfaces, combine baking soda and a little water to
make a cleaning paste. Use a soft rag to rub the surface with the mix
until the stains are removed.
It is recommended that the glass be cleaned two or three times during
each heating season, depending on the circumstances present.
Ensure stove is completely cold prior to cleaning
or using enamel touch up paint.
IMPORTANT
Exterior glass may be cleaned with an non-ammonia based household
cleaner and warm water as desired (a gas stove glass cleaner is recommended).
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
31
Replacing A Damaged Barrier
•
If the barrier becomes damaged, the barrier shall be replaced
with the manufacturer’s barrier for this appliance.
•
For use with barrier Part No. J7488 (model CI1500DVF)
or Part No. J7489 (model CI2500DVF). Follow installation
instructions.
Barrier
To remove the damaged barrier
1. Make sure the unit is off and cold.
2. Carefully remove trivet and top casting.
3. Pull the damaged barrier from the barrier retainers (Retainers are on
the back side of the front casting) See Figure 40.
Barrier Retainers
Installing is the reverse of removal
1. For CI1500DVF replace barrier with Part No. J7488. For CI2500DVF
replace barrier with Part No. J7489.
2. Reinstall top casting and trivet.
Figure 40
32
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
Optional Room Air Blower
WIRING DIAGRAMS
Wiring diagrams are provided here for reference purposes only. This
information is also provided on schematics attached directly to the appliance on a pullout panel located within the control compartment.
CAUTION: Label all wires prior to disconnection when servicing controls. Wiring errors can cause improper and dangerous
operation.
ATTENTION: Au moment de l'entretien des commandes,
étiquetez tous les fils avant de les débrancher. Des erreurs
de cáblage peuvent entraîner un fonctionnement inadéquat
et dangereux.
IMPORTANT: Ground supply wire must be connected to the green
wire attached to the green ground screw. Failure to do so will
result in a potential safety hazard. The appliance must be electrically grounded in accordance with local codes or, in the absence
of local codes, the National Electrical Code, ANSI/NFPA 70 - latest
edition. (In Canada, the current CSA C22-1 Canadian Electrical
Code - latest edition.
WARNING: The power cord must be plugged directly into a properly
grounded three-prong 120 Volt, 60 Hz wall receptacle. Do not cut
or remove the grounding prong from this plug. Do not route power
cord under or in front of appliance.
SIT Millivolt Wiring Diagram
If any of the original wire as supplied must be replaced,
it must be replaced with Type AWM105° C – 18 GA. wire.
Power Cord
TH
TP
TH
TP
Blower
Assembly
(Shown
Rotated 90
Degrees CCW)
Thermopile
Blower
Mounting
Bracket
* SWITCH
* ON/OFF Switch, Optional
Thermostat Remote
Control Receiver
Figure 41 - SIT Millivolt Wiring Diagram
Optional Wall Thermostat
Black
If an optional wall thermostat is to be installed, install the thermostat
per the manufacturers instructions (provided with the thermostat).
Failure to follow manufacturers instructions could result in a malfunction. Pay special attention to the thermostat location requirements.
If the location requirements are not adhered to the appliance, erratic
operation or failure may occur.
Black
White
White
Black
Do not mount the thermostat where it may be affected by:
• Radiant heat from this appliance, fireplaces, sun or other heat
sources.
• Drafts or dead spots behind doors or in corners.
• Hot or cold air from ducts.
Fan Disc
Rheostat
Figure 42 - Blower Wiring Diagram
33
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
LIGHTING INSTRUCTIONS – SIT MILLIVOLT GAS VALVE
FOR YOUR SAFETY READ BEFORE LIGHTING
WARNING: If you do not follow these instructions exactly, a fire or explosion may result causing property damage, personal
injury or loss of life.
• Immediately call your gas supplier from a neighbor’s phone. Follow the gas
supplier’s instructions.
• If you cannot reach your gas supplier, call the fire department.
C. Use only your hand to push in or turn the gas control knob. Never use tools.
If the knob will not push in or turn by hand, don’t try to repair it, call a
qualified service technician. Force or attempted repair may result in a fire or
explosion.
D. Do not use this appliance if any part has been under water. Immediately call
a qualified service technician to inspect the appliance and to replace any
part of the control system and any gas control which has been under water.
A. This appliance has a pilot which must be lighted by a piezo igniter. When
lighting the pilot, follow these instructions exactly.
B. BEFORE LIGHTING smell all around the appliance area for gas. Be sure to
smell next to the floor because some gas is heavier than air and will settle
on the floor.
WHAT TO DO IF YOU SMELL GAS:
• Do not try to light any appliance.
• Do not touch any electric switch; do not use any phone in your building.
LIGHTING INSTRUCTIONS
1. STOP! Read the safety information above on this label.
2. (If applicable) Set the thermostat to lowest setting. Turn wall on/off
switch, unit mounted on/off switch or remote control switch "OFF."
3. Turn OFF all electric power to the appliance.
4. Access the control compartment.
5. Push in gas control knob slightly and turn clockwise
to "OFF."
NOTE: Knob cannot be turned from "PILOT" to "OFF" unless knob is
pushed in slightly. Do Not force.
6. Wait five (5) minutes to clear out any gas. Then smell for gas,
including near the floor. If you smell gas, STOP! Follow "B" in the
safety information above on this label. If you don't smell gas, go to the
next step.
7. Find pilot - located in firebox on the same plane as the top of the burner.
8. Turn knob on gas control counterclockwise
to "PILOT."
9. Push in control knob all the way and hold in. Immediately light the pilot
by triggering the piezo igniter (pushing the button) until pilot lights.
Continue to hold the control knob in for about 1-1/2 minutes after the
pilot is lit. Release knob and it will pop back up. Pilot should remain
lit. If it goes out, repeat steps 5 through 9.
• If knob does not pop up when released, stop and immediately call
your service technician or gas supplier.
• If the pilot will not stay lit after several tries, turn the gas control
knob to "OFF" and call your service technician or gas supplier.
10. Turn gas control knob counterclockwise
to "ON."
11. Close control compartment.
12. (If applicable) Turn on all electrical power to the appliance.
13. (If applicable) Set thermostat to desired setting. Turn wall on/off switch,
unit mounted on/off switch or remote control switch "ON."
Gas Control Valves
Pilot Assemblies
OT
PIL
TH
LO W
P IL O T
it
ON
SIT
TP
OF F
TPTH
HI
IN
OUT
9-5/8"
HI
LO
OT
PIL
OFF
Robertshaw
IN OUT
ON
Gas Control Knobs
PILOT
T FF
LO O
PI
Honeywell
ON
LO
HI
IN
OUT
TPTH
TO TURN OFF GAS TO APPLIANCE
TP
HI
TH
O FF
it
PIL O T
ON
4. Push in gas control knob slightly and turn clockwise
PIL
OT
1. (If applicable) Set the thermostat to lowest setting. Turn wall on/off
switch, unit mounted on/off switch or remote control switch "OFF."
2. Turn OFF all electric power to the appliance, if service is to be
performed.
3. Access the control compartment.
LO W
Do not force.
5. Close the main line gas shut-off valve.
6. Close control compartment.
to "OFF."
DANGER
HOT GLASS WILL
CAUSE BURNS.
DO NOT TOUCH GLASS
UNTIL COOLED.
NEVER ALLOW CHILDREN
TO TOUCH GLASS.
A barrier designed to reduce the risk of burns from the hot viewing glass is provided with this
appliance and shall be installed for the protection of children and other at-risk individuals.
34
P/N 900327-00 Rev. 0
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
6-3/4"
INSTRUCTIONS D’ALLUMAGE - VANNE GAZ MILLIVOLT SIT
POUR PLUS DE SÉCURITÉ, LIRE AVANT D’ALLUMER
AVERTISSEMENT. Quiconque ne respecte pas à la lettre les instructions dans la présente notice risque de déclencher un
incendie ou une explosion entraînant des dommages, des blessures ou la mort.
A.Cet appareil est muni d’une veilleuse qui doit être allumée avec un allumeur
piézo-électrique. Respectez les instructions ci-dessous à la lettre.
B. AVANT L’ALLUMAGE: Avant d’allumer la veilleuse, reniflez tout autour de
l’appareil pour déceler une odeur de gaz. Reniflez près du plancher, car certains
gaz sont plus lourds que l’air et peuvent s’accumuler au niveau du sol.
QUE FAIRE SI VOUS SENTEZ UNE ODEUR DE GAZ :
• Ne pas tenter d’allumer d’appareil.
• Ne touchez à aucun interrupteur ; ne pas vous servir des téléphones se trouvant
dans le bâtiment.
• Appelez immédiatement votre fournisseur de gaz depuis un voisin. Suivez
les instructions du fournisseur.
• Si vous ne pouvez rejoindre le fournisseur, appelez le service des
incendies.
C. Ne pousser ou tourner la manette d’admission du gaz qu’à la main. Ne
jamais employer d’outil à cette fin. Si la manette reste coincée, ne tentez
pas de la réparer; appelez un technicien qualifié. Quiconque tente de
forcer la manette ou de la réparer peut provoquer une explosion ou un
incendie.
D. N’utilisez pas cet appareil s’il a été plongé dans l’eau, même
partiellement. Faites inspecter l’appareil par un technicien qualifié et
remplacez toute partie du système de contrôle et toute commande qui ont
été plongés dans l’eau.
INSTRUCTIONS D’ALLUMAGE
• Si la manette ne se soulève pas d’elle-même lorsqu’on la relâche,
arrêter et appeler immédiatement un technicien qualifié ou le
fournisseur de gaz.
• Si la veilleuse ne reste pas allumée après plusieurs tentatives,
réglez la manette d’admission du gaz à la position OFF et appelez un
technicien qualifié ou le fournisseur de gaz.
10. Tournez le bouton de réglage du gaz en sens inverse des aiguilles d’une
montre
jusqu’à sa position de marche “ON”.
11. Fermer le compartiment de contrôle.
12. (Si applicable) Mettez l’appareil sous tension.
13. (Si applicable) Réglez le thermostat à la température désirée. Tournez
l’interrupteur murale, l’interrupteur sur l’unité ou le contrôle à distance
à "ON."
Vanne Gaz Millivolt
PIL
Millivolt Pilot
OT
TH
P IL O T
SIT
it
ON
LO W
TP
OF F
HI
TPTH
brûleur.
IN
OUT
9-5/8"
Bouton de réglage du gaz
HI
LO
T
PILO
OFF
Robertshaw
IN OUT
ON
8. Tournez le bouton de contrôle sur la valve à gaz dans le sens antihoraire
vers "Pilote".
9. Enfoncez le bouton de réglage jusqu’au fond et gardez-le enfoncé. Allumez
immédiatement la veilleuse en déclenchant l’allume-gaz à étincelle (en
poussant le bouton) jusqu’à ce que la veilleuse s’enflamme. Continuez
de tenir le bouton de réglage enfoncé pendant environ 90 secondes après
l’allumage de la veilleuse. Relâchez le bouton et il sortira subitement. La
veilleuse devrait rester allumée. Si elle s’éteint, répétez les étapes 5 à 8
inclusivement.
PILOT
T FF
LO O
PI
Honeywell
ON
LO
HI
IN
1. ARRÊTEZ ! Lisez les instructions de sécurité sur la portion supérieure de
cette étiquette.
2. (Si applicable) Réglez le thermostat à la température la plus basse. Tournez
l’interrupteur murale, l’interrupteur sur l’unité ou le contrôle à distance à
"OFF. "
3. Coupez l’alimentation électrique de l’appareil.
4. Accédez au compartiment de contrôle.
5. Enfoncez légèrement le bouton de réglage du gaz et tournez-le dans le sens des
aiguilles d’une montre
jusqu’à la position d’arrêt “OFF”.
Remarque: Il est impossible de tourner le bouton de “PILOT” à “OFF” à
moins qu’il ne soit légèrement enfoncé. Ne le forcez pas.
6. Attendre cinq (5) minutes pour laisser échapper tout le gaz. Reniflez tout
autour de l’appareil, y compris près du plancher, pour déceler une odeur
de gaz. Si vous sentez une odeur de gaz, ARRÊTEZ ! Passez à l’étape B des
instructions de sécurité sur la portion supérieure de cette étiquette. S’il n’y a
pas d’odeur de gaz, passez à l’étape suivante.
7. Trouver le pilote – Situé dans l’âtre sur la même surface que le dessus du
OUT
TPTH
TP
HI
TH
LO W
COMMENT COUPER L’ADMISSION DE GAZ DE L’APPAREIL
O FF
it
PIL O T
ON
PIL
OT
1. (Si applicable) Réglez le thermostat à la température la plus basse. Tournez
l’interrupteur murale, l’interrupteur sur l’unité ou le contrôle à distance à
"OFF. "
2. Coupez l’alimentation électrique de l’appareil s’il faut procéder à l’entretien.
3. Accédez au compartiment de contrôle.
4. Enfoncez légèrement le bouton de réglage du gaz et tournez-le dans le
sens des aiguilles d’une montre
jusqu’à la position d’arrêt “OFF”.
Ne forcez pas le bouton.
5. Fermer la valve de gaz principale.
6. Fermer le compartiment de contrôle.
DANGER
VITRE CHAUDE
RISQUE DE BRÛLURES.
NE TOUCHEZ PAS UNE VITRE
NON REFROIDIE.
NE LAISSEZ JAMAIS UN ENFANT
DE TOUCHER LA VITRE.
L'écran pare-étincelles fourni avec ce foyer réduit le risque de brûlure en cas de contact accidentel
avec la vitre chaude et doit être installé pour la protection Des enfants et Des personnes à risques.
P/N 900328-00 Rev. 0
35
REMARQUE : LES SCHÉMAS ET LES ILLUSTRATIONS NE SONT PAS À L’ÉCHELLE
6-3/4"
RATING LABELS
MODEL NO.
CI1500DVF
SERIES
MANUFACTURED AT: AUBURN, WA
MANUFACTURED AT: AUBURN, WA
FOR USE WITH NATURAL GAS.
EQUIPE POUR GAZ NATUREL
ALTITUDE
0-4500 FT (0-1370 M)
MIN. GAS SUPPLY PRESS (“WC)
PRESS MIN. D’ALIMENTATION (“CE)
4.5”
MANIFOLD PRESSURE (“WC)
PRESSION CE TUBULURE (“CE)
3.5”
MANUFACTURER’S RECOMMENDED ORIFICE SIZE
DIMENSION DE L’INJECTEUR RECOMMANDE PAR
#37
MANUFACTURIER (DMS)
MAX INPUT (BTUH)
ENTRÉE MAX (BTUH)
28,000
MIN INPUT (BTUH)
ENTRÉE MIN (BTUH)
17,500
FOR USE WITH NATURAL GAS.
EQUIPE POUR GAZ NATUREL
ALTITUDE
0-4500 FT (0-1370 M)
MIN. GAS SUPPLY PRESS (“WC)
PRESS MIN. D’ALIMENTATION (“CE)
4.5”
MANIFOLD PRESSURE (“WC)
PRESSION CE TUBULURE (“CE)
3.5”
MANUFACTURER’S RECOMMENDED ORIFICE SIZE
DIMENSION DE L’INJECTEUR RECOMMANDE PAR
.121
MANUFACTURIER (DMS)
MAX INPUT (BTUH)
ENTRÉE MAX (BTUH)
38,500
MIN INPUT (BTUH)
25,500
ENTRÉE MIN (BTUH)
ELECTRICAL RATING/EXIGENCES ELECTRIQUES:
OPTIONAL FAN/SOUFFLEUR OPTIONAL
ELECTRICAL RATING/EXIGENCES ELECTRIQUES:
OPTIONAL FAN/SOUFFLEUR OPTIONAL
MINIMUM
-UNIT/APPAREIL: MILLIVOLT
1 ph
60 HZ
120 VOLTS
LESS THAN 5 AMPS
SIDEWALLS
FLOOR
CEILING OR ALCOVE HEIGHT
BACK/CORNER 45
VENT SURFACES: TOP
SIDES
BOTTOM
CLEARANCES TO
COMBUSTIBLE
MATERIAL
2”
0”
62”
4”
3”
1”
1”
ALCOVE MAXIMUM DEPTH
MUR ADJACENTS
PLANCHER
PLAFOND OU HAUTEUR D'ALCÔVE
EN ARRIÈRE ET COIN 45 ANGLE
SURFACES D’AERATION: DESSUS
COTES
BAS
DEGAGEMENT
MINIMUM DE
MATERIAUX
COMBUSTIBLES
48”
50.8mm
0mm
1574.8mm
101.6mm
76.2mm
25.4mm
25.4mm
PROFONDEUR D'ALCÔVE MAXIMALE
1219.2mm
DIRECT VENT GAS STOVE / APPAREIL A GAZ AVEC EVACUATION DIRECTE
VENTED GAS STOVE HEATER – NOT FOR USE WITH SOLID FUEL.
FOYER DE CHAUFFAGE AU GAZ A EVACUATION - NE DOIT PAS ETRE UTILISE AVEC UN
COMBUSTIBLE SOLIDE.
FOR USE WITH GLASS DOOR CERTIFIED WITH THE APPLIANCE ONLY.
N’UTILISER SEULEMENT QUE LA PORTE DE VERRE CERTIFIE AVEC L’APPAREIL.
“CAUTION: Do not operate the appliance with glass removed, cracked or broken.
Replacement of panel should be done by a licensed or qualified service person.”
“This appliance is equipped at the factory for use with natural gas only. Units using
propane must be field converted using the LP conversion kit, P/N H3705”
For use only with barrier Part No. J7488. Follow installation instructions.
Utiliser uniquement avec l’écran no J7488. Suivre les instructions d’installation.
FINAL INSPECTION BY:
C
MINIMUM
-UNIT/APPAREIL: MILLIVOLT
1 ph
60 HZ
120 VOLTS
LESS THAN 5 AMPS
SIDEWALLS
FLOOR
CEILING OR ALCOVE HEIGHT
BACK/CORNER 45
VENT SURFACES: TOP
SIDES
BOTTOM
CLEARANCES TO
COMBUSTIBLE
MATERIAL
2”
0”
62”
4”
3”
1”
1”
ALCOVE MAXIMUM DEPTH
MUR ADJACENTS
PLANCHER
PLAFOND OU HAUTEUR D'ALCÔVE
EN ARRIÈRE ET COIN 45 ANGLE
SURFACES D’AERATION: DESSUS
COTES
BAS
DEGAGEMENT
MINIMUM DE
MATERIAUX
COMBUSTIBLES
48”
50.8mm
0mm
1574.8mm
101.6mm
76.2mm
25.4mm
25.4mm
PROFONDEUR D'ALCÔVE MAXIMALE
1219.2mm
DIRECT VENT GAS STOVE / APPAREIL A GAZ AVEC EVACUATION DIRECTE
VENTED GAS STOVE HEATER – NOT FOR USE WITH SOLID FUEL.
FOYER DE CHAUFFAGE AU GAZ A EVACUATION - NE DOIT PAS ETRE UTILISE AVEC UN
COMBUSTIBLE SOLIDE.
FOR USE WITH GLASS DOOR CERTIFIED WITH THE APPLIANCE ONLY.
N’UTILISER SEULEMENT QUE LA PORTE DE VERRE CERTIFIE AVEC L’APPAREIL.
“CAUTION: Do not operate the appliance with glass removed, cracked or broken.
Replacement of panel should be done by a licensed or qualified service person. ”
“This appliance is equipped at the factory for use with natural gas only. Units using
propane must be field converted using the LP conversion kit, P/N H3706”
For use only with barrier Part No. J7489. Follow installation instructions.
Utiliser uniquement avec l’écran no J7489. Suivre les instructions d’installation.
FINAL INSPECTION BY:
ANSI Z2188-2014, CSA 2.33-2014, CAN/CGA-2.17-M91
US
ANSI Z2188-2014, CSA 2.33-2014, CAN/CGA-2.17-M91
C
Report No. 14-162
US
Report No. 14-162
VENTED GAS STOVE HEATERS
FOYER DE CHAUFFAGE AU GAZ A EVACUATION
P/N 900383-00
VENTED GAS STOVE HEATERS
FOYER DE CHAUFFAGE AU GAZ A EVACUATION
P/N 900384-00
SERIAL NUMBER/NOMBRE DE SERIE
SERIAL NUMBER/NOMBRE DE SERIE
XXXXX XXXXX
XXXXX XXXXX
IIIIIIIIIIIIIIIIIIII
XXXXXXXXXXXXXXXX
36
MODEL NO.
CI2500DVF
SERIES
P/N 900383-00 REV. 0
IIIIIIIIIIIIIIIIIIII
XXXXXXXXXXXXXXXX
P/N 900384-00 REV. 0
MAINTENANCE SCHEDULE
Annually (Before the onset of the Burning Season)
Maintenance Task
Inspecting/Cleaning Burner, Logs
Accomplishing Person
Qualified Service Technician
and Controls
Procedure
Inspect valve and ensure it is properly operating. Check piping for
leaks. Vacuum the control compartment, fireplace logs and burner
area.
Check Flame Patterns and Flame Height
Qualified Service Technician
Refer to Figure 30 on Page 27 and verify the flame pattern and height
displayed by the appliance conforms to the picture. Flames must not
impinge on the logs. Ensure flames are steady (not lifting or floating).
Inspecting/Cleaning Pilot
Qualified Service Technician
Refer to Figure 29 on Page 27. Remove any surface build-up on pilot
and burner assembly. Wipe the pilot nozzles, igniter/flame rod and
hood. Ensure the pilot flame engulfs the flame sensor as shown.
Checking Vent System
Qualified Service Technician
Inspect the vent system at the top and at the base (within the firebox)
for signs of blockage or obstruction. Look for any signs of dislocation or deterioration of the vent components. NOTE: Excessive
condensation can cause corrosion of caps, pipe and fittings (excessive
condensation can be caused by long lateral runs, too many elbows
and/or exterior portions of the system being exposed to cold weather).
Also inspect wall straps or plumbers's tape to ensure it is secure and
in place.
Appliance Checkout
Qualified Service Technician
Perform the appropriate appliance checkout procedure detailed in this
manual.
Replacing Glowing Ember Materials
Homeowner/Qualified Service
Remove old glowing embers (rockwool) and vacuum the ember place-
Technician
ment area. Place new glowing embers as described on Page 26 (see
Figures 25 and 26).
Periodically (After the Burning Season)
Maintenance Task
Cleaning Firebox Interior
Accomplishing Person
Homeowner
Procedure
Carefully remove logs, glowing embers (rockwool), volcanic stone and
volcanic stone. Vacuum out interior of the firebox. Clean firebox walls
and log grate. Replace logs, glowing embers and volcanic stone as
detailed in this manual.
Check Flame Patterns and Flame Height
Homeowner
Refer to Figure 30 on Page 27 and verify the flame pattern and height
displayed by the appliance conforms to the picture. Flames must not
impinge on the logs.
Checking Vent System
Homeowner
Inspect the vent system at the top and at the base (within the firebox)
for signs of blockage or obstruction. Look for any signs of dislocation
of the vent components.
Cleaning Front Glass Enclosure Panel
Homeowner
Clean as necessary following the directions provided in this manual.
Do not touch or attempt to clean glass while hot.
37
TROUBLESHOOTING THE Millivolt GAS CONTROL SYSTEM
NOTE: Before troubleshooting the gas control system, be sure external gas shut off valve (located at gas supply inlet) is in the “ON”
position.
Important: Valve system troubleshooting should only be accomplished by a qualified service technician.
SYMPTOM
1. Spark igniter will not light pilot after
repeated triggering of igniter button.
POSSIBLE CAUSES
CORRECTIVE ACTION
A. Defective igniter
(no spark at electrode).
Check the gap between the electrode and pilot. It should
be between 1/8” and 3/16." If the gap is out of this
range, adjust the gap or replace the pilot.
B. Defective or misaligned electrode at pilot
(spark at electrode).
Using a match, light pilot. If pilot lights, turn off pilot
and trigger the igniter button again. If pilot lights, an
improper gas mixture caused the bad lighting and a
longer purge period is recommended. If pilot will not
light – check gap at electrode (igniter rod) and pilot – It
should be between 1/8” and 3/16". If the gap is out of
this range replace the pilot (Figure 29 on Page 27).
C. Gas supply pressure errant.
Check inlet gas pressure. It should be within the limits
as marked on the rating plate.
D. Pilot orifice plugged.
Clean or replace pilot orifice.
2. Pilot will not stay lit after
carefully following the lighting
instructions.
A. Defective pilot generator
(thermocouple).
Check pilot flame, it must impinge on thermocouple
(Figure 29 on Page 27). Clean and/or adjust pilot
for maximum flame impingement on thermocouple.
Ensure that the connection between the valve and
thermocouple are tight and secure.
3. Pilot burning, no gas to burner, Valve
knob “ON,” Wall Switch “ON.”
A. Wall switch or wires defective.
Check wall switch and wires for proper connections.
Jumper wire across terminals at wall switch, if burner
comes on, replace defective wall switch. If okay, jumper
wires across wall switch wires at valve, if burner comes
on, wires are faulty or connections are bad.
B. Thermopile may not be generating sufficient millivoltage.
Check thermopile with millivolt meter. Take reading
at thermopile terminals of gas valve. Should read
325 millivolts minimum with optional wall switch
“OFF.” Replace faulty thermopile if reading is below
specified minimum.
C. Plugged burner orifice.
Check burner orifice for stoppage and remove.
A. Pilot flame may be too low or blowing (high)
causing the pilot/valve safety to drop out.
Clean and/or adjust pilot flame for maximum flame
impingement on thermocouple (Figure 29 on Page 27).
4. Frequent pilot/burner outage problem.
38
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
REPLACEMENT PARTS LIST
Cast Body Components
Contact an IHP dealer to obtain any of these parts. Please contact IHP
for the phone number of your nearest IHP dealer.
WARNING
Never use substitute materials. Use of non-approved
parts can result in poor performance and safety hazards.
WARNING
Failure to position the parts in accordance with these
diagrams or failure to use only parts specifically
approved with this appliance may result in property
damage or personal injury.
AVERTISSEMENT
Risque de dommages ou de blessures si les pièces
ne sont pas installées conformément à ces schémas
et ou si des pièces autres que celles spécifiquement
approuvées avec cet appareil sont utilisées.
Gas Controls
Description
Where Used
Item
#
Cat. No.
Description
12
H3703
Glass Panel Enclosure Assembly, Complete
CI1500DVF Series
12
H3704
Glass Panel Enclosure Assembly, Complete
CI2500DVF Series
29b
527
Knob, Rheostat, 1 ea.
Where Used
All
---
69L21
Latch, 1 ea.
13
24M10
Orifice, Main Burner, #37,
Natural Gas, 1 ea.
CI1500DVF Series
All
13
H1073
Orifice, Main Burner, .121”,
Natural Gas, 1 ea.
CI2500DVF Series
---
55M62
Paint, Touch-up for enamel, 1/2
oz - Hunter Green, 1 ea.
CI1506DVF & CI2506DVF
---
55M63
Paint, Touch-up for enamel, 1/2
oz - Ivory White, 1 ea.
CI1508DVF-2 & CI2508DVF-2
---
55M61
Paint, Touch-up for enamel, 1/2
oz - Maj. Brown, 1 ea.
CI1504DVF & CI2504DVF
---
55M60
Paint, Touch-up for enamel, 1/2
oz - Mid. Blue, 1 ea.
CI1502DVF & CI2502DVF
14
27K30
Switch, ON/OFF (Rocker
Switch), 1 ea.
19
66M53
Ash Lip, Enamel Hunter Green,
1 ea.
CI1506DVF
19
66M93
Ash Lip, Enamel Hunter Green,
1 ea.
CI2506DVF
19
H2163
Ash Lip, Enamel Ivory White,
1 ea.
CI1508DVF-2
19
H2164
Ash Lip, Enamel Ivory White,
1 ea.
CI2508DVF-2
19
66M52
Ash Lip, Enamel Maj. Brown,
1 ea.
CI1504DVF
19
66M92
Ash Lip, Enamel Maj. Brown,
1 ea.
CI2504DVF
19
66M51
Ash Lip, Enamel Mid. Blue,
1 ea.
CI1502DVF
19
66M91
Ash Lip, Enamel Mid. Blue,
1 ea.
CI2502DVF
19
55M89
Ash Lip, Painted Black, 1 ea.
CI1500DVF
All
Item
#
Cat.
No.
1
H1657
Valve Assembly – Natural Gas, SIT
30
H2211
Gas Train Assembly, MV, Natural Gas (LP
units will also require LB-102158A)
CI1500DVF Series
30
H2212
Gas Train Assembly, MV, Natural Gas (LP
units will also require LB-102158B)
CI2500DVF Series
2
10K86
Piezo Igniter, Push Button (wire not
included)
All
3
69L17
Pilot Assembly, Natural Gas
All
5
H3737
Pilot Shield
All
6
74L56
Pilot Tube
All
19
66M01
Ash Lip, Painted Black, 1 ea.
CI2500DVF
---
H3697
RB Regulator (Hi/Lo)- Natural Gas, SIT
(H1656) – Converts LP Valve to NG
All
22
66M57
Door Casting, Lower Access Enamel Hunter Green, 1 ea.
CI1506DVF
---
H3698
RB Regulator (Hi/Lo)- Propane Gas, SIT –
Converts NG Valve to LP
All
22
66M97
Door Casting, Lower Access Enamel Hunter Green, 1 ea.
CI2506DVF
7
74L57
Thermocouple
All
22
H2169
60J79
Thermopile (pilot generator)
All
Door Casting, Lower Access Enamel Ivory White, 1 ea.
CI1508DVF-2
8
---
H3364
Tube, Gas Valve
All
22
H2170
H1061
Wire Harness, Valve
All
Door Casting, Lower Access Enamel Ivory White, 1 ea.
CI2508DVF-2
--15
H6212
Electrode and Cable
All
22
66M56
Door Casting, Lower Access Enamel Maj. Brown, 1 ea.
CI1504DVF
22
66M96
42M72
Burner Assembly
CI1500DVF Series
Door Casting, Lower Access Enamel Maj. Brown, 1 ea.
CI2504DVF
9
10
42M73
Burner Assembly
CI2500DVF Series
22
66M55
H3705
CI1500DVF Series
Door Casting, Lower Access Enamel Mid. Blue, 1 ea.
CI1502DVF
Conversion Kit, NG to LP (RB Reg., Pilot
Orifice, Burner Orifice & Label)
22
66M95
---
H3706
CI2500DVF Series
Door Casting, Lower Access Enamel Mid. Blue, 1 ea.
CI2502DVF
Conversion Kit, NG to LP (RB Reg., Pilot
Orifice, Burner Orifice & Label)
22
55M90
H4335
Relief Door Assembly, CI1500
CI1500DVF Series
Door Casting, Lower Access Painted Black, 1 ea.
CI1500DVF
-----
H4336
Relief Door Assembly, CI2500
CI2500DVF Series
22
66M02
CI2500DVF
11
93L32
Gas Line Connector, Flexible, With Shut-Off
Valve, 1 ea.
Door Casting, Lower Access Painted Black, 1 ea.
31
J7488
Barrier
CI1500DVF Series
32
J7489
Barrier
CI2500DVF Series
All
Miscellaneous Parts
---
All
39
REPLACEMENT PARTS LIST (continued)
Cast Body Components (continued)
Item
#
Cat. No.
Description
Where Used
23
H5324
Front Face and Door Set Assembly, Hunter Green, 1 ea.
CI1506DVF
23
H5322
Front Face and Door Set
Assembly,Hunter Green, 1 ea.
CI2506DVF
23
H5325
Front Face and Door Set Assembly, Ivory White, 1 ea.
CI1508DVF-2
23
H5323
Front Face and Door Set Assembly, Ivory White, 1 ea.
CI2508DVF-2
23
H5327
Front Face and Door Set Assembly, Majolica Brown, 1 ea.
CI1504DVF
23
H5321
Front Face and Door Set Assembly, Majolica Brown, 1 ea.
CI2504DVF
23
H5326
Front Face and Door Set Assembly, Midnight Blue, 1 ea.
CI1502DVF
23
H5320
Front Face and Door Set Assembly, Midnight Blue, 1 ea.
CI2502DVF
23
H5318
Front Face and Door Set Assembly, Flat Black, 1 ea.
CI1500DVF
23
H5319
Front Face and Door Set Assembly, Flat Black, 1 ea
CI2500DVF
24
H1023
Leg Casting, Enamel Hunter
Green, 1 ea.
CI1506DVF & CI2506DVF
24
H2173
Leg Casting, Enamel Ivory
White, 1 ea.
CI1508DVF-2 & CI2508DVF-2
24
H1022
Leg Casting, Enamel Maj.
Brown, 1 ea.
CI1504DVF & CI2504DVF
24
H1021
Leg Casting, Enamel Mid. Blue,
1 ea.
CI1502DVF & CI2502DVF
24
66M08
Leg Casting, Painted Black,
1 ea.
CI1500DVF & CI2500DVF
25
H1007
Side Casting, Left - Enamel
Hunter Green, 1 ea.
CI1506DVF
25
H1031
Side Casting, Left - Enamel
Hunter Green, 1 ea.
CI2506DVF
25
H2174
Side Casting, Left - Enamel
Ivory White, 1 ea.
CI1508DVF-2
25
H2175
Side Casting, Left - Enamel
Ivory White, 1 ea.
CI2508DVF-2
25
H1006
Side Casting, Left - Enamel
Maj. Brown, 1 ea.
25
H1030
25
25
26
66M05
Side Casting, Right, Painted Black,
1 ea.
CI1500DVF
26
66M15
Side Casting, Right, Painted Black,
1 ea.
CI2500DVF
27
66M81
Top Casting, Stove, Enamel Hunter
Green, 1 ea.
CI1506DVF
27
H1043
Top Casting, Stove, Enamel Hunter
Green, 1 ea.
CI2506DVF
27
H2178
Top Casting, Stove, Enamel Ivory
White, 1 ea.
CI1508DVF-2
27
H2179
Top Casting, Stove, Enamel Ivory
White, 1 ea.
CI2508DVF-2
27
66M80
Top Casting, Stove, Enamel Maj.
Brown, 1 ea.
CI1504DVF
27
H1042
Top Casting, Stove, Enamel Maj.
Brown, 1 ea.
CI2504DVF
27
66M79
Top Casting, Stove, Enamel Mid.
Blue, 1 ea.
CI1502DVF
27
H1041
Top Casting, Stove, Enamel Mid.
Blue, 1 ea.
CI2502DVF
27
55M97
Top Casting, Stove, Painted Black,
1 ea.
CI1500DVF
27
66M18
Top Casting, Stove, Painted Black,
1 ea.
CI2500DVF
28
66M85
Trivet, Enamel Hunter Green, 1 ea.
CI1506DVF
28
H1047
Trivet, Enamel Hunter Green, 1 ea.
28
H2180
Trivet, Enamel Ivory White, 1 ea.
CI1508DVF-2
28
H2183
Trivet, Enamel Ivory White, 1 ea.
CI2508DVF-2
28
66M84
Trivet, Enamel Maj. Brown, 1 ea.
CI1504DVF
28
H1046
Trivet, Enamel Maj. Brown, 1 ea.
CI2504DVF
28
66M83
Trivet, Enamel Mid. Blue, 1 ea.
CI1502DVF
28
H1045
Trivet, Enamel Mid. Blue, 1 ea.
CI2502DVF
28
55M98
Trivet, Painted Black, 1 ea.
CI1500DVF
28
66M19
Trivet, Painted Black, 1 ea.
CI2500DVF
CI2506DVF
Room Air Blower System (Optional Kit)
H0767
Blower Kit (BK-CI), Complete
All
Rheostat, Blower Speed Control
(knob not included)
All
All
29
528
---
42M60
Switch, Temperature Control (thermally activated fan disc)
CI1504DVF
16
35M66
Ember Strip (bottom front refractory), 1 ea.
CI1500DVF Series
Side Casting, Left - Enamel
Maj. Brown, 1 ea.
CI2504DVF
16
42M61
Ember Strip (bottom front refractory), 1 ea.
CI2500DVF Series
H1005
Side Casting, Left - Enamel
Mid. Blue, 1 ea.
CI1502DVF
17
88L53
Glowing Embers, Bag of (1 oz.
rockwool), 1 ea.
H1029
Side Casting, Left - Enamel
Mid. Blue, 1 ea.
CI2502DVF
18
H1065
Log Set, 7 pc.
CI1500DVF Series
18
H1075
Log Set, 7 pc.
CI2500DVF Series
Log Sets
All
25
66M04
Side Casting, Left - Painted
Black, 1 ea.
CI1500DVF
25
66M14
Side Casting, Left - Painted
Black, 1 ea.
CI2500DVF
---
H8159
Touch-Up Paint, Metallic Black
(12 oz aerosol)
All
26
H1010
Side Casting, Right, Enamel
Maj. Brown, 1 ea.
CI1504DVF
---
55M62
Paint, Touch-up for enamel,
1/2 oz - Hunter Green, 1 ea.
All
26
H1034
Side Casting, Right, Enamel
Maj. Brown, 1 ea.
CI2504DVF
---
55M63
Paint, Touch-up for enamel,
1/2 oz - Ivory White, 1 ea.
All
26
H1009
Side Casting, Right, Enamel
Mid. Blue, 1 ea.
CI1502DVF
---
55M61
Paint, Touch-up for enamel,
1/2 oz - Maj. Brown, 1 ea.
All
26
H1033
Side Casting, Right, Enamel
Mid. Blue, 1 ea.
CI2502DVF
---
55M60
Paint, Touch-up for enamel,
1/2 oz - Mid. Blue, 1 ea.
All
Touch-Up Paint Kits
40
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
REPLACEMENT PARTS DIAGRAMS
1
11
19
L
30
12
15
E
N
4
N
O
X
25
2
L
31
32
5
7
E
N
N
O
X
24
26
27
8
3
6
13
14
28
23
18
9
Front View
*
*
*
22
16
Log Set Does Not Include Ember Strip (purchased
separately)
29
17
10
Front View
*
*
*
*
*
*
29b
41
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
Firebox Liner Kits
ACCESSORY COMPONENTS
The firebox liner kits include panels for the rear and side walls of the
firebox. The panels have brick-like features in relief. These kits can be
retrofitted into previously installed appliances.
Product Reference Information
Cat.#
Model
Description
Ship. Wt.
Ship. Volume
F2326
CI1500DVF
Painted Black
245 lb.
14.6 cu. ft.
F2327
CI1502DVF
Midnight Blue
245 lb.
14.6 cu. ft.
H0773
BLK-CI15
Firebox Liner Kit CI1500DVF Series
F2328
CI1504DVF
Majolica Brown
245 lb.
14.6 cu. ft.
H0774
BLK-CI25
Firebox Liner Kit CI2500DVF Series
F2329
CI1506DVF
Hunter Green
245 lb.
14.6 cu. ft.
F2330
CI1508DVF-2
Ivory White
245 lb.
14.6 cu. ft.
F2331
CI2500DVF
Painted Black
354 lb.
25.3 cu. ft.
F2332
CI2502DVF
Midnight Blue
354 lb.
25.3 cu. ft.
25.3 cu. ft.
F2333
CI2504DVF
Majolica Brown
354 lb.
F2334
CI2506DVF
Hunter Green
354 lb.
25.3 cu. ft.
F2335
CI2508DVF-2
Ivory White
354 lb.
25.3 cu. ft.
Cat. No.
Model
Description
(ref. form # 775151M)
Room Air Blower Kit
The BK-CI blower provides constant velocity forced air circulation. It
includes a variable speed control rheostat and a thermally activated fan
disc.
Blower
Warming Shelves
These attractive warming shelves are designed to be functional for
placing food to stay warm. The shelves extend on both sides of the
stove top and add an attractive accent. See Page 44 for installation
instructions.
Cat. No.
Model
H0757
WS-CI150
Warming Shelves, CI1500 Black
Description
H0758
WS-CI152
Warming Shelves, CI1502 Mid Blu
H0759
WS-CI154
Warming Shelves, CI1504 Maj Bwn
H0760
WS-CI156
Warming Shelves, CI1506 Hu Grn
H2159
WS-CI158-2
H0762
WS-CI250
Warming Shelves, CI1508-2 Ivory White
Warming Shelves, CI2500 Black
H0763
WS-CI252
Warming Shelves, CI2502 Mid Blu
H0764
WS-CI254
Warming Shelves, CI2504 Maj Bwn
H0765
WS-CI256
Warming Shelves, CI2506 Hu Grn
H2158
WS-CI258-2
Warming Shelves, CI2508-2 Ivory White
(ref. form # 775149M)
Side View of Warming Shelf
Variable Speed
Control Rheostat
Cat. No.
Model
H0767
BK-CI
Thermally
Activated
Switch
Top View of Warming Shelf
Full View Showing Warming Shelves Installed
Description
Blower Kit CI1500 and CI2500
(ref. form # 775146M)
42
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
ACCESSORY COMPONENTS (cont.)
Cost Effective Solution
• Simple On/Off operation
• Works with millivolt and low voltage electronic
ignition controls
Flame and Heat modulation
Thermostatic or Manual modes
•
•
•
•
•
•
LCD Display
Up to 9 hour Count down Timer
Includes batteries
Child lock
Low battery indicator
Receiver may be wall mounted or placed in
the valve compartment
• Includes solenoid for SIT millivolt valves
• Thermostatic, manual or up to 9 hour Countdown Timer modes
• 3 Fan speed settings
• Child lock
• Low battery indicator
• Wall clip included
• Includes batteries
Model No.
Description
H8861
RC-S-STAT
Remote Control
G-Fire Remote, Simple On/Off
Cat. No.
Model No.
Description
H8840
KIT-RC-G-FIRE
Remote Control
Remote With Hi/Low Flame, Millivolt
Remote, LCD Stat, Thermostat, On/Off
Cat. No.
Kit includes:
Remote and Receiver
Cat. No.
Model No.
Description
H8862
RC-S-MODMV
Remote Control
Wall Thermostat
• Wall surface mounted
• Thermostat or manual ON/OFF operation
• Large LCD screen to display room and set
temperature in ºF and ºC
• Connects to wall switch wire
Wall Thermostat, On/Off and
Thermostatic functions
State-of-the-art control with touch screen
operation
• Backlit LCD display
• Wall mounted docking station for the transmitter
• Thermostatic or manual ON/OFF
• Programmable Weekday/Weekend modes
• Flame icon and low battery indicator
• Receiver may be wall mounted or placed in
the valve compartment
• Includes batteries
Remote, Touch Screen, Thermostat, On/Off
Cat. No.
Model No.
Description
H8865
RC-S-TOUCH
Remote Control
Cat. No.
Model No.
Description
H8864
WS-S-TSTAT
Wall Thermostat
Manual or up to 3 hr Countdown Timer
modes
•
•
•
•
•
•
•
•
•
•
LCD display
Displays room temp. in ºF or ºC
Flame icon and low battery indicator
Includes batteries
Wall clip included
Receiver may be wall mounted or placed in
the control compartment
Includes white face plate
Flame icon
Low battery indicator
Batteries included
Wall Control
•
•
•
•
4-button timer with 30/60/120/OFF minutes
Wall surface mounted
Connects to wall switch wire
Perfect for rental and resort applications
Remote, Two Button, Timer,
On/Off Or Timer Mode
Wall Switch, Countdown Timer
Cat. No.
Model No.
Description
Cat. No.
H8860
RC-S-1
Remote Control
H8863
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
Model No.
Description
WS-S-TMR
Wall Switch
43
OPTIONAL WARMING SHELVES KIT
Kit Contents:
2 ea. Warming Shelves
4 ea. Decorative Brackets
4 ea. Insets (CI1500 Series)
6 ea. Insets (CI2500 Series)
4 ea. Screws, 6mm x 20mm
1 ea. Instruction Sheet
4. Place the insets (4 ea. for the CI1500 series or 6 ea. for the CI2500
series) into the recessed areas on both warming shelves as shown in
Figures 45 and 46. NOTE: Common ceramic tiles (4-1/4” square) can
be used in place of insets on the warming shelves (available at most
home improvement stores).
Place insets as
shown here.
Tools Required:
Phillips Screwdriver
If Optional Warming Shelves are purchased, install as follows:
Installation Instructions:
1. Lift off trivet, then stove top and set aside.
CAUTION
The cast iron stove top is very heavy and may require
a minimum of two people to lift; one person on each
side (the CI1500 series cast top weighs ~20 pounds
and the CI2500 series cast top weighs ~40 pounds).
2. Install decorative brackets to both warming shelves using the screws
provided (see Figure 43).
Figure 45 - Install Insets
5. Reinstall stove top into position (see Figure 46).
Install Screws Provided
Figure 46 - Top View of Warming Shelves Installed
Figure 43 - Assemble Shelves to Brackets
3. Using the existing screws on the stove body, install both warming
shelve assemblies as shown in Figure 44. Tighten screws just enough
to level shelves.
Proper Use Instructions:
These attractive shelves are designed to be functional for placing food
to stay warm. For cleaning instructions see Cleaning Enamel Surfaces
on Page 31.
Install, using
the existing
screws.
IMPORTANT NOTES:
• NEVER PLACE ANYTHING ON THE SHELVES WHICH EXCEEDS 80
POUNDS (36 KILOGRAMS).
• NEVER PLACE FOOD CONTAINERS OR OTHER MATERIALS ON THE
SHELVES THAT MAY BE SUBJECT TO MELTING.
Figure 44 - Installing onto Stove Body
44
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
Innovative Hearth Products
IronStrike™ Brand Gas Fireplaces, Stoves and Inserts
20 Year Limited Warranty
THE WARRANTY
Innovative Hearth Products ("IHP") 20 Year Limited Warranty warrants your IronStrike™ brand gas fireplace or insert ("Product") to be free from defects in materials and
workmanship at the time of manufacture. The Product body and firebox carry the 20 Year Limited Warranty. Ceramic glass carries the 20 Year Limited Warranty against thermal
breakage only. After installation, if covered components manufactured by IHP are found to be defective in materials or workmanship during the 20 Year Limited Warranty
period and while the Product remains at the site of the original installation, IHP will, at its option, repair or replace the covered components. If repair or replacement is not
commercially practical, IHP will, at its option, refund the purchase price or wholesale price of the IHP product, whichever is applicable. IHP will also pay IHP prevailing labor
rates, as determined in its sole discretion, incurred in repairing or replacing such components for up to five years. THERE ARE EXCLUSIONS AND LIMITATIONS to this 20
Year Limited Warranty as described herein.
COVERAGE COMMENCEMENT DATE
Warranty coverage begins on the date of installation. In the case of new home construction, warranty coverage begins on the date of first occupancy of the dwelling or six
months after the sale of the Product by an independent IHP dealer/distributor, whichever occurs earlier. The warranty shall commence no later than 24 months following the
date of product shipment from IHP, regardless of the installation or occupancy date.
EXCLUSIONS AND LIMITATIONS
This 20 Year Limited Warranty applies only if the Product is installed in the United States or Canada and only if operated and maintained in accordance with the printed instructions accompanying the Product and in compliance with all applicable installation and building codes and good trade practices.
This warranty is non-transferable and extends to the original owner only. The Product must be purchased through a listed supplier of IHP and proof of purchase must be
provided. The Product body and firebox carry the 20 Year Limited Warranty from the date of installation. Vent components, trim components and paint are excluded from this
20 Year Limited Warranty. The following do not carry the 20 Year Limited Warranty but are warranted as follows:
Burner – Repair or replacement for one year from the date of installation
Gas components – Repair or replacement for one year from the date of installation
Gaskets – Repair or replacement for one year from the date of installation
Gold & nickel plating – Replacement for two years from date of installation. Excludes tarnishing
Logs – Replacement for one year from the date of installation against thermal breakage only
Optional blowers & remote controls – Repair or replacement for one year from the date of installation
Optional glass doors – Repair or replacement for 90 days from the date of installation
Tempered glass – Replacement for one year from the date of installation
Labor coverage – Prevailing IHP labor rates apply for the warranty period of the component
Parts not otherwise listed carry a 90 day warranty from the date of installation.
Whenever practicable, IHP will provide replacement parts, if available, for a period of 10 years from the last date of manufacture of the Product.
IHP will not be responsible for: (a) damages caused by normal wear and tear, accident, riot, fire, flood or acts of God; (b) damages caused by abuse, negligence, misuse, or
unauthorized alteration or repair of the Product affecting its stability or performance (The Product must be subjected to normal use. The Product is designed to burn either
natural or propane gas only. Burning conventional fuels such as wood, coal or any other solid fuel will cause damage to the Product, will produce excessive temperatures and
could result in a fire hazard.); (c) damages caused by failing to provide proper maintenance and service in accordance with the instructions provided with the Product; (d)
damages, repairs or inefficiency resulting from faulty installation or application of the Product.
IHP is not responsible for inadequate fireplace system draft caused by air conditioning and heating systems, mechanical ventilation systems, or general construction conditions
which may generate negative pressure in the room in which the appliance is installed. Additionally IHP assumes no responsibility for drafting conditions caused by venting
configurations, adjoining trees or buildings, adverse wind conditions or unusual environmental factors and conditions that affect the operation of the unit.
This 20 Year Limited Warranty covers only parts and labor as provided herein. In no case shall IHP be responsible for materials, components or construction, which are not
manufactured or supplied by IHP or for the labor necessary to install, repair or remove such materials, components or construction. Additional utility bills incurred due to
any malfunction or defect in equipment are not covered by this warranty. All replacement or repair components will be shipped F.O.B. from the nearest stocking IHP factory.
LIMITATION ON LIABILITY
It is expressly agreed and understood that IHP’s sole obligation and the purchaser’s exclusive remedy under this warranty, under any other warranty, expressed or implied, or
in contract, tort or otherwise, shall be limited to replacement, repair, or refund, as specified herein.
In no event shall IHP be liable for any incidental or consequential damages caused by defects in the Product, whether such damage occurs or is discovered before or after
repair or replacement, and whether such damage is caused by IHP’s negligence. IHP has not made and does not make any representation or warranty of fitness for a particular
use or purpose, and there is no implied condition of fitness for a particular use or purpose.
IHP makes no expressed warranties except as stated in this 20 Year Limited Warranty. The duration of any implied warranty is limited to the duration of this expressed warranty.
No one is authorized to change this 20 Year Limited Warranty or to create for IHP any other obligation or liability in connection with the Product. Some states and provinces
do not allow the exclusion or limitation of incidental or consequential damages, so the above limitations or exclusions may not apply to you. The provisions of this 20 Year
Limited Warranty are in addition to and not a modification of or subtraction from any statutory warranties and other rights and remedies provided by law.
INVESTIGATION OF CLAIMS AGAINST WARRANTY
IHP reserves the right to investigate any and all claims against this 20 Year Limited Warranty and to decide, in its sole discretion, upon the method of settlement.
To receive the benefits and advantages described in this 20 Year Limited Warranty, the appliance must be installed and repaired by a licensed contractor approved by IHP.
Contact IHP at the address provided herein to obtain a listing of approved dealers/distributors. IHP shall in no event be responsible for any warranty work done by a contractor
that is not approved without first obtaining IHP's prior written consent.
HOW TO REGISTER A CLAIM AGAINST WARRANTY
In order for any claim under this warranty to be valid, you must contact the IHP dealer/distributor from which you purchased the product. If you cannot locate the dealer/
distributor, then you must notify IHP in writing. IHP must be notified of the claimed defect in writing within 90 days of the date of failure. Notices should be directed to the IHP
Warranty Department at 1508 Elm Hill Pike, Suite 108; Nashville, TN 37210 or visit our website at WWW.IRONSTRIKE.US.COM.
Printed in U.S.A. © 2013 Innovative Hearth Products LLC
P/N 900197-00, Rev. NC 12/2013
Innovative Hearth Products
1508 Elm Hill Pike, Suite 108 • Nashville, TN 37210
45
Product reference information
When ordering repair parts, always give the following information:
We recommend that you record the following important information
about your appliance. Please contact your IHP dealer for any questions
or concerns.
1. The model number of the appliance.
2. The serial number of the appliance.
3. The part number.
4. The description of the part.
5. The quantity required.
6. The installation date of the appliance.
Replacement parts
See Page 39 for a complete replacement parts list. Use only parts supplied from the manufacturer.
Normally, all parts should be ordered through your IHP distributor or
dealer. Parts will be shipped at prevailing prices at time of order.
If you encounter any problems or have any questions concerning the
installation or application of this system, please contact your dealer.
Innovative Hearth Products
1508 Elm Hill Pike, Suite 108
Nashville, TN 37210
visit us at IronStrike.us.com
Model Number______________________________________________________
Serial Number______________________________________________________
Date Installed_______________________________________________________
Your Dealer's Name__________________________________________________
Fuel Type (Check one)
c
Natural Gas
c
Propane Gas (LP)
IHP reserves the right to make changes at any time, without notice, in design, materials,
specifications, and prices, and also to discontinue colors, styles, and products. Consult your
local distributor for fireplace code information.
Printed in U.S.A. © 2013 Innovative Hearth Products
46
P/N 900129-00 Rev. A 01/2015
P900129-00
1508 Elm Hill Pike, Suite 108 • Nashville, TN 37210

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement

Languages