OWNER’S MANUAL MINI HI-FI SYSTEM Please read this manual carefully before operating your set and retain it for future reference. CM9750 (CM9750, CMS9750F) www.lg.com 2 Getting Started Safety Information 1 CAUTION Getting Started RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK) NO USER-SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. This lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product. WARNING: TO PREVENT FIRE OR ELECTRIC SHOCK HAZARD, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE. CAUTION: The apparatus should not be exposed to water (dripping or splashing) and no objects filled with liquids, such as vases, should be placed on the apparatus. WARNING: Do not install this equipment in a confined space such as a book case or similar unit. CAUTION: Do not use high voltage products around this product. (ex. Electrical swatter) This product may malfunction due to electrical shock. CAUTION: This product employs a Laser System. To ensure proper use of this product, please read this owner’s manual carefully and retain it for future reference. Shall the unit require maintenance, contact an authorized service center. Use of controls, adjustments or the performance of procedures other than those specified herein may result in hazardous radiation exposure. To prevent direct exposure to laser beam, do not try to open the enclosure. CAUTION: Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. Slots and openings in the cabinet are provided for ventilation and to ensure reliable operation of the product and to protect it from over heating. The openings shall be never be blocked by placing the product on a bed, sofa, rug or other similar surface. This product should not be placed in a builtin installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer’s instruction has been adhered to. Getting Started CAUTION concerning the Power Cord Most appliances recommend they be placed upon a dedicated circuit; The Power Plug is the disconnecting device. In case of an emergency, the Power Plug must remain readily accessible. This device is equipped with a portable battery or accumulator. Safety way to remove the battery or the battery from the equipment: Remove the old battery or battery pack, follow the steps in reverse order than the assembly. To prevent contamination of the environment and bring on possible threat to human and animal health, the old battery or the battery put it in the appropriate container at designated collection points. Do not dispose of batteries or battery together with other waste. It is recommended that you use local, free reimbursement systems batteries and accumulators. The battery shall not be exposed to excessive heat such as sunshine, fire or the like. Declaration of Conformity Hereby, LG Electronics European Shared Service Center B.V., declares that this MINI HI-FI SYSTEM is compliant with the essential requirements and other relevant provisions of Directive 1999/5/EC. The complete Declaration of Conformity may be requested through the following postal address: LG Electronics European Shared Service Center B.V. European Standard Team Krijgsman 1 1186 DM Amstelveen The Netherlands or can be requested at our dedicated DoC website: http://www.lg.com/global/support/cedoc/cedoc# This device is a 2.4 GHz wideband transmission system, intended for use in all EU member states and EFTA countries. 1 Getting Started That is, a single outlet circuit which powers only that appliance and has no additional outlets or branch circuits. Check the specification page of this owner’s manual to be certain. Do not overload wall outlets. Overloaded wall outlets, loose or damaged wall outlets, extension cords, frayed power cords, or damaged or cracked wire insulation are dangerous. Any of these conditions could result in electric shock or fire. Periodically examine the cord of your appliance, and if its appearance indicates damage or deterioration, unplug it, discontinue use of the appliance, and have the cord replaced with an exact replacement part by an authorized service center. Protect the power cord from physical or mechanical abuse, such as being twisted, kinked, pinched, closed in a door, or walked upon. Pay particular attention to plugs, wall outlets, and the point where the cord exits the appliance. 3 4 Table of Contents Table of Contents 1 Getting Started 2 Safety Information 6 Unique Features 6Accessories 7 Playable file Requirement 7 – Music file requirement 7 – Compatible USB Devices 7 – USB device requirement 8 Remote control 10 Front panel 11 Rear panel 3Operating 16 16 17 17 18 18 18 18 19 20 20 22 2Connecting 23 23 12 12 24 12 12 13 13 14 14 15 15 How to Affix the Ferrite Core – Affix the Ferrite Core for power cord and speaker cables Connecting to speakers – Attaching the speaker light cables to the unit Optional Equipment Connection – AUX IN Connection – AUX OUT Connection – PORT. IN Connection – USB Connection – Antenna Connection 25 25 25 25 25 26 27 27 27 28 28 30 Basic Operations – CD/USB Operations – Auto Play – Selecting a folder and an MP3/WMA file – Deleting an MP3/WMA file Playback Effect – DJ EFFECT – SCRATCH Effect – AUTO DJ Using Bluetooth® wireless technology – Listening to music stored on the Bluetooth devices – Pairing your unit and Bluetooth device through NFC Tag Using the Music Flow Bluetooth App – Install “Music Flow Bluetooth” App onto Your Bluetooth Device – Activate Bluetooth with “Music Flow Bluetooth” App Radio Operations – Listening to the radio – Improving poor FM reception – Presetting the Radio Stations – Deleting all the saved stations – Seeing information about a Radio station Sound adjustment – Setting the sound mode – Setting the USER EQ Advanced Operations – Recording to USB – Programmed Playback Table of Contents 31 31 31 31 Other Operations – Turn off the sound temporarily – CHILDSAFE Mode – Displaying file information (ID3 TAG) 31 – DEMO 32 – Using Microphone 32 – LIGHTING 33 – Setting the Clock through “Music Flow Bluetooth” App 33 – Using your player as an alarm clock 34 – Sleep Timer Setting 34 – Dimmer 34 Auto power down 35 – AUTO POWER On 35 – Auto function change 36 LG Sound Sync 37Troubleshooting 37 – General 5 1 2 3 4 4Troubleshooting 39 General specifications 5 5Appendix 40 Speakers specifications 40 Trademarks and Licenses 41Maintenance 41 – Notes on Discs 41 – Handling the Unit 6 Getting Started Unique Features 1 Bluetooth® Accessories Please check and identify the supplied accessories. Getting Started Listens to music stored on your Bluetooth device. Portable In Listens to music from your portable device. (MP3, Notebook, etc.) FM Antenna (1) Playback effects Listens to music with various sound and playback effects. USB Direct Recording Records music to your USB device. Music Flow Bluetooth Music Flow Bluetooth is an App designed to let you take control of some of LG’s latest Audio devices. Refer to page 23. LG Sound Sync Controls volume level of this unit by the remote control of your LG TV that is compatible with LG Sound Sync. Remote Control (1) Batteries (2) Getting Started Playable file Requirement MP3/WMA file compatibility with this unit is limited as follows. yy Sampling frequency : within 32 to 48 kHz (MP3), within 32 to 48 kHz (WMA) yy Bit rate : within 32 to 320 kbps (MP3), 40 to 192 kbps (WMA) yy Maximum files : Data CD : 999 / USB : 2000 Compatible USB Devices yy MP3 Player : Flash type MP3 player. yy USB Flash Drive : Devices that support USB2.0 or USB1.1. yy The USB function of this unit does not support all USB devices. USB device requirement yy Devices which require additional program installation when you have connected it to a computer, are not supported. yy Do not extract the USB device while in operation. yy Maximum folders : Data CD : 99 / USB : 200 yy For a large capacity USB, it may take longer than a few minute to be searched. yy File extensions : “.mp3”/ “.wma” yy To prevent data loss, back up all data. yy Certain MP3/WMA files may not be played depending on the type or format of the file. yy If you use a USB extension cable or USB hub, the USB device is not recognized. yy CD-ROM file format : ISO 9660/ JOLIET yy Using NTFS file system is not supported. (Only FAT(16/ 32) file system is supported.) yy We recommend that you use Easy-CD Creator, which creates an ISO 9660 file system. The DTS is not supported. In case of DTS audio format, audio is not output. You have to set the disc format option to [Mastered] in order to make the discs compatible with the LG players when formatting rewritable discs. When setting the option to Live File System, you cannot use it on LG players. (Mastered/Live File System : Disc format system for Windows Vista) yy This unit recognizes up to 2000 files. yy External HDD, Card readers, Locked devices, or hard type USB devices are not supported. yy USB port of the unit cannot be connected to PC. The unit cannot be used as a storage device. yy Some USB may not work with this unit. 1 Getting Started Music file requirement 7 8 Getting Started Remote control • • • • • • • • • • a • • • • • • • • • • 1 (Power) : Switches the unit ON or OFF. B (Open/Close) : Opens and closes the disc tray. PRESET.FOLDER W/S : 1 Getting Started -- Searches for a folder of MP3/WMA files. When a CD/USB containing MP3/WMA files in several folders is being played, press PRESET.FOLDER W/S to select the folder you want to play. -- Chooses a preset number for a radio station. FUNCTION : Selects the function and input source. MUTE @ : Mutes the sound. VOL +/- : Adjusts speaker volume. PROGRAM/MEMORY : -- Stores radio stations. -- Deletes all the saved stations. -- Creates a programmed list you want to listen to. USB REC : USB direct recording. SLEEP : Sets the system to turn off automatically at a specified time. (Dimmer : The display window will be darkened by half.) Battery Installation Remove the battery cover on the rear of the Remote Control, and insert two (size AAA) batteries with 4 and 5 matched correctly. Getting Started 9 • • • • • • • • • • c • • • • • • • • • • 0 to 9 numerical buttons : Selects numbered tracks, files, or preset number. TUNING-/+ : Selects the radio stations. RDS/SET : C/V (Skip/Search) : -- RDS (Radio Data System) (Refer to the page 26.) -- Skips Fast backward or Forward. -- Searches for a section within a track/file. -- Confirms the setting. Z ENTER : PTY : Searches radio stations by radio type. -- Stops playback or recording. • • • • • • • • • • d • • • • • • • • • • -- Cancels DELETE function. CLOCK : Sets a clock and checks a time. d/M (Play/Pause) : ALARM : With the ALARM function you can turn CD, USB play and Tuner reception on at a desired time. -- Starts or pauses playback. -- Selects STEREO/MONO. SOUND EFFECT : Chooses sound impressions. AUTO DJ : Selects the AUTO DJ mode. (For more information refer to page 19) DELETE : -- Deletes MP3/WMA files. (USB only). -- Deletes a song on the programmed list. INFO -- Sees informations about your music. An MP3 file often come with ID3 tag. The tag gives the Title, Artist, Album or Time information. -- Sees the address of connected Bluetooth device in Bluetooth mode. DJ EFFECT : Selects DJ EFFECT mode. (Refer to page 18) DJ LEVEL +/- : Adjusts the level of DJ EFFECT sound. * : This button is not available. 1 Getting Started • • • • • • • • • • b • • • • • • • • • • REPEAT (MENU) : Listens to your tracks/files repeatedly or randomly. Getting Started 10 Front panel i j k l m n o 1 Getting Started a e b f c g d h p qr s a1/!(Power) b DJ EFFECT Selects DJ EFFECT mode. (For more information refer to page 18). cBASS BLAST Selects BASS or STANDARD effect directly. dAUTO DJ / RDS Selects the AUTO DJ mode. (For more information refer page 19). / Uses RDS (Radio Data System) (Refer to the page 26.) eUSB REC Records to USB. fFOLDER Moves to folder and file in selection mode. gENTER Selects a folder when searching a file. hDELETE -Deletes a song on the programmed list. -Deletes MP3/WMA files. (USB only). i : You can easily connect to Bluetooth devices through NFC Tag. (Refer to page 22) jUSB 1 Port You can play or record sound files by connecting the USB device. t u vw x kBASS Adjusts BASS sound level when setting USER EQ. lDisplay window mMASTER VOLUME Adjusts speaker volume. nTREBLE Adjusts TREBLE sound level when setting USER EQ. oUSB 2 Port You can play or record sound files by connecting the USB device. pSCRATH & CONTROL Turn clockwise or counterclockwise to make Scratch sound. / Sets Delay value in X-BOOM PLUS mode. / Adjust DJ EFFECT level. qX-BOOM PLUS/DEMO Press to select X-BOOM PLUS mode. / Shows Demo mode. rMIC. jack Getting Started sY/U LIGHTING - Skips Fast backward or Forward. - Searches for a section within a track/file. 11 Turns on/off the lighting effects. Stops playback or cancels DELETE function. tDisc tray T uMIC VOL. - Starts or pauses playback. - Selects Stereo/Mono. vPORT. IN jack USER EQ Controls sound register. 1 wFUNCTION Selects the function and input source. xSEARCH Searches a folder and a file on CD/USB function. LG EQ Chooses sound impressions. Rear panel a b c aPower cord >>Caution yy Connect the power cord to wall outlet directly if possible. Or when you use an extension cable, it is highly recommended to use an extension cable of 110 V / 15 A or 230 V / 15 A, otherwise the unit may not operate properly because of the lack of power supply. yy Do not overload the extension cord with excessive electrical load. d e bSPEAKERS connector cSPEAKER LIGHTING SYSTEM dANTENNA (FM) eAUX IN (L/R) AUX OUT (L/R) Getting Started I EJECT Opens and closes the disc tray. 12 2 Connecting How to Affix the Ferrite Core Connecting to speakers Ferrite core may not be provided depending on each nation’s regulations. Connect the speaker cable plugs to the SPEAKERS connector. Make sure to connect the speaker’s plug to the corresponding colored speaker connector when connecting the plug. Affix the Ferrite Core for power cord and speaker cables Connecting You must affix a ferrite core in order to reduce or eliminate electrical interference. 1. Pull the stopper [a] of the ferrite core to open. 2. Wind the power cord around the ferrite core twice (Once for 110 V cord). Wind the SPEAKERS cables around the ferrite core once. Wind the SPEAKER LIGHTING SYSTEM cables around the ferrite core once. 3. Close the ferrite core until it clicks. Attaching the speaker light cables to the unit To connect the speaker light cable to the unit, insert the cable to SPEAKER LIGHTING SYSTEM connectors on the unit. >>Caution yy Make sure that the jacks and the speakers are matched correctly. yy Make sure to connect the cables to connectors tightly on the unit. Connecting >>Caution yy Do not try to lift the speaker alone. It needs two persons to lift the speaker. Otherwise it may result in the speaker malfunction and cause personal injury and/or property damage. yy When you connect the speakers to the unit, make sure to connect the speaker’s cable and plug to the corresponding speaker connector. yy Do not use the unit in a limited space. It may damage a person’s hearing. It is recommended to use it in a wide space. yy Be careful to make sure children not to put their hands or any objects into the opening speaker duct hole. Optional Equipment Connection AUX IN Connection Connect an output of auxiliary device (Camcorder, TV, Player, etc) to the AUX IN (L/R) connector. If your device has only one output for audio (mono), connect it to the left audio jack on the unit. Red Audio cable White yy The speakers contain magnet parts, so color irregularity may occur on the TV screen or PC monitor screen. Please use the speakers far away from either TV screen or PC monitor. yy Avoid looking at the speaker lights for a long time. It may cause damage to eyesight. DVD, Blu-ray player etc. 2 Connecting yy Check the volume level before playing music to prevent infirm, child, and pregnant women from being shocked by the sudden and loud sound from the unit. 13 14 Connecting AUX OUT Connection PORT. IN Connection Connect an input of auxiliary device to the AUX OUT (L/R) connector. Connect an output (earphone or line out) of portable device (MP3 or PMP etc) to the PORT. IN connector. If your device has only one input for audio(mono), connect it to the left audio jack on the unit. 2 Connecting Auxiliary device Audio cable Portable cable X-BOOM PLUS You can connect two units to play music together. 1. Connect AUX OUT connector on a unit to the AUX IN connector on the other unit using Audio cable. 2.Press X-BOOM PLUS/DEMO on the unit connected through AUX OUT. X-BOOM PLUS is displayed. MP3 player etc. 3.Rotate SCRATCH & CONTROL clockwise or counterclockwise to adjust Delay setting. Listening to music from your portable player or external device 4.Press X-BOOM PLUS/DEMO to save the Delay setting. The unit can be used to play the music from many types of portable player or external device. ,,Note yy This function is available on CD, USB 1, USB 2, BT or PORTABLE Function. yy The initial Delay is 0 ms and the Delay becomes to 30 ms when you press X-BOOM PLUS/DEMO. The connected device’s Delay may differ. If Audio Sync is not matched, adjust Delay of X-BOOM PLUS/DEMO to synchronize sound. yy It is available to adjust the Delay from 0 ms to 100 ms. Synchronizing tempo is not available depending on devices. yy Delay value is saved when the unit turns off. 1. Connect the portable player to the PORT. IN connector of the unit. Or Connect the external device to the AUX IN connector of the unit. 2. Turn the power on by pressing 1/!. 3.Press FUNCTION to select PORTABLE or AUX Function. 4. Turn on the portable player or external device and start it playing. Connecting 15 USB Connection Antenna Connection Connect a USB device (or MP3 player, etc.) to the USB ports on the unit. Connect the supplied FM antenna for listening to the radio. USB device Connect the FM wire antenna to the FM antenna connector. 2 ,,Note Removing the USB device from the unit : 1. Choose a different function/mode or press Z ENTER on the remote control or I on the unit twice in a row. 2. Remove the USB device from the unit. ,,Note yy Be sure to fully extend the FM wire antenna. Connecting FM antenna 16 Operating Basic Operations CD/USB Operations 1. Insert the disc by pressing B on the remote control or EJECT on the unit Or connect the USB device to the USB port. 2. Select CD or USB function by pressing FUNCTION. To 3 Operating Do this Press Z ENTER on the remote Stop control or I on the unit. Press d/M on the remote control Playback or T on the unit. Press d/M on the remote control Pause or T on the unit during playback. Searching Press C/V on the remote for a section control or Y/U on the unit within a track/ during playback and release it at file the point you want to listen to. Selecting Press 0 to 9 numerical buttons on a track/file the remote control to go to the directly desired file or track directly. -- In stop status, Press C/V on the remote control or Y/U on the unit to go to the next/previous track/file. -- During Playback, (1) By using C/V buttons : Press V on the remote control or U on the unit to go to the next Skipping to track/file. the next/ Playing less than 2 seconds, press previous C on the remote control or track/file Y on the unit to go to the previous track/file. Playing after 3 seconds, press C on the remote control or Y on the unit to go to the beginning of the track/file. (2) By using SEARCH : Rotate SEARCH on the unit and press d/M to play the track/ file. Press REPEAT(MENU) on the Playing remote control repeatedly. Refer repeatedly or to the note for details about the randomly display change. ,,Note yy The display changes in the following order. USB MP3/WMA CD AUDIO CD RPT 1 RPT 1 RPT 1 RPT*DIR RPT DIR - RPT ALL RPT ALL RPT ALL RANDOM RANDOM RANDOM OFF OFF OFF *DIR : Directory yy When you play the programmed list, only RPT 1 and RPT ALL are available. yy Even after restarting the unit or switching one function to another, you can listen to music from the point where it’s last been played. yy If you leave the disc tray open for 5 minutes, it will close automatically. Operating Auto Play -- AUDIO/MP3/WMA CD is played automatically after Disc tray is open and then closed. -- Automatically switches to the CD function if Disc tray is open and then closed when there is no disc in Disc tray. 17 ,,Note yy CD / USB Folders/Files are recognized as below. * Selecting a folder and an MP3/WMA file On the unit 1.Press FOLDER and rotate SEARCH until a desired folder appears. 3 Operating 2.Press ENTER and rotate SEARCH until a desired file appears. Press T to play it. On the remote control 1.Press PRESET.FOLDER W/S on the remote control repeatedly until a desired folder appears. 2.Press d/M to play it. The first file of folder will play. yy If there is no file in a folder, the folder will not appear. yy Folders will be presented as the following order; ROOT FOLDER 1 FOLDER 3 FOLDER 7 FOLDER 8 FOLDER 5 FOLDER 6 yy File will be played from $ file No.1 to $ file No.14 one by one. yy Files and folders will be presented in order recorded and may be presented differently according to the record circumstances. yy *ROOT : The first screen you can see when a computer recognize the USB is “ROOT”. 18 Operating Deleting an MP3/WMA file You can delete file, folder or format by pressing DELETE. This function is supported only in stop status. (USB only) 1. -Select the file you want to delete and press DELETE. -Select the folder you want to delete by pressing FOLDER and rotating SEARCH on the unit and press DELETE. Or select the folder you want to delete by pressing PRESET.FOLDER W/S on the remote control and press DELETE. 3 -Press and hold DELETE to format the USB device. Or Operating Press DELETE repeatedly during selecting the MP3/WMA file. The display changes in the following order. - DEL FILE : Deletes file - DEL DIR : Deletes folder - FORMAT : Formats USB 2. To delete file/folder or format, press d/M on the remote control or press T on the unit. If you want to exit the current mode, press Z ENTER on the remote control or press I on the unit. >>Caution yy Do not extract the USB device during operation. (play, delete, etc.) yy Regular back up is recommended to prevent data loss. yy The delete function may not be supported according to the USB status. (lock, etc.) Playback Effect The unit supports various sound and playback effects : DJ EFFECT, SCRATCH, AUTO DJ. DJ EFFECT It allows you to enjoy DJ EFFECT such as Flanger/ Phaser/Chorus/Delay sound effect. 1. Press DJ EFFECT to select a desired DJ EFFECT (FLANGER, PHASER, CHORUS, DELAY, OFF). 2. Turn SCRATCH & CONTROL clockwise or counterclockwise to adjust the DJ EFFECT level between 0 to 15. ,,Note yy The DJ EFFECT mode is displayed for 3 seconds when a DJ EFFECT Key is inputted. yy The gage starts at the beginning with an initial 7 level. yy The current gage level is displayed when adjusting gage. yy If the function changed or the unit is turned off and on, DJ EFFECT mode with DJ EFFECT is turned off. SCRATCH Effect You can output and mix the sound effects of the SCRATCH. Rotating SCRATCH & CONTROL to mix the scratch sound. -- You can hear effect of scratch sound depending on the direction in which you rotate SCRATCH & CONTROL. Operating 19 AUTO DJ Auto DJ blends the end of one song into the beginning of another for seamless playback. It equalizes volume across tracks/files for uninterrupted playback. Press AUTO DJ on the remote control repeatedly, the display changes as followings. RANDOM (AUTO DJ RANDOM) -> RPT (AUTO DJ SEQUENTIAL) -> (AUTO DJ OFF) Mode OFF Display Window (AUTO DJ OFF) Description - RANDOM (AUTO DJ RANDOM) The music is played randomly on this mode. REPEAT RPT (AUTO DJ SEQUENTIAL) The music is played repeatedly on this mode. ,,Note yy AUTO DJ mode does not support searching for a section within a track/file or to play repeatedly or randomly. yy If you move to other functions or stop the music using I on the unit (or Z ENTER on the remote control) on AUTO DJ mode, AUTO DJ will be disable. yy AUTO DJ is not supported in the music file whose length is less than 60 seconds. yy During recording, AUTO DJ is not available. yy Only AUTO DJ SEQUENTIAL is selected when played the programmed list. 3 Operating RANDOM 20 Operating Using Bluetooth® wireless technology About Bluetooth Bluetooth® is wireless communication technology for short range connection. The sound may be interrupted when the connection interfered by the other electronic wave or you connect the bluetooth in the other rooms. 3 Operating Connecting individual devices under Bluetooth® wireless technology does not incur any charges. A mobile phone with Bluetooth® wireless technology can be operated via the Cascade if the connection was made via Bluetooth® wireless technology. Available Devices : Mobile phone, MP3, Laptop, PDA. Bluetooth Profiles In order to use Bluetooth® wireless technology, devices must be able to interpret certain profiles. This unit is compatible with following profile. A2DP (Advanced Audio Distribution Profile) Listening to music stored on the Bluetooth devices Pairing your unit and Bluetooth device Before you start the pairing procedure, make sure the Bluetooth feature is activated on your Bluetooth device. Refer to your Bluetooth device’s user guide. Once a pairing operation is performed, it does not need to be performed again. 1. Select the Bluetooth function by using FUNCTION until BT function is selected. “BT READY” appears on the display window. 2. Operate the Bluetooth device and perform the pairing operation. When searching for this unit with the Bluetooth device, a list of the devices found may appear in the Bluetooth device display depending on the type of Bluetooth device. Your unit appears as “LG CM9750(XX)”. ,,Note yy XX means the last two digits of Bluetooth address. For example, if your unit has a Bluetooth address such as 9C:02:98:4A:F7:08, you will see “LG CM9750(08)” on your Bluetooth device. yy Depending on the Bluetooth device type, some devices may have a different pairing process. Enter the PIN code (0000) as needed. yy You can connect this unit with up to 3 Bluetooth devices simultaneously using the same method as described above, only in the Bluetooth function. yy The multi pairing connection is only supported on Android or iOS devices. (Multi pairing connection may not be supported depending on the connected device specifications.) yy Removable/detachable Bluetooth devices (Ex: Dongle etc.) will not support multi pairing. Operating 3. When this unit is successfully connected with your Bluetooth device, “PAIRED” appears on the display window and change to Bluetooth device name soon. ,,Note yy "PAIRED" will momentarily appear on the display when you connect other devices for multi pairing. yy If the device name is unavailable, “_” will be displayed. 4. Listen to music. To play a music stored on your Bluetooth device, refer to your Bluetooth device’s user guide. yy When using Bluetooth® technology, you have to make a connection between the unit and the bluetooth device as close as possible and keep the distance. However, it may not work well in certain situations as described below : -- There is a obstacle between the unit and the bluetooth device. -- There is a device using same frequency with Bluetooth® technology such as a medical equipment, a microwave or a wireless LAN device. yy You should connect your bluetooth device to this unit again when you restart it. yy Even if this unit connected up to 3 Bluetooth devices in the Bluetooth mode, you can play and control music by using only one of the connected devices. ,,Note yy When this unit connected with multiple Bluetooth devices, only one device which you are playing keeps Bluetooth connection when you change the function to the others. yy The sound may be interrupted when the connection has interference from other electronic devices. yy You may not control the Bluetooth device with this unit. yy Depending on the type of the device, you may not be able to use the Bluetooth function. yy You can enjoy wireless system using phone, MP3, Notebook, etc. yy The more distance between the unit and the bluetooth device, the lower the sound quality becomes. yy Bluetooth connection will be disconnected when the unit is turned off or the Bluetooth device gets far from the unit. yy When Bluetooth connection is disconnected, connect the bluetooth device to the unit again. yy When a Bluetooth device is not connected, “BT READY” appears on the display window. yy When you use the BT function, adjust the volume to a proper level on the Bluetooth device. yy If it is not in the BT function, only one device can be connected. yy If a Bluetooth device is connected when using LG TV, LG TV is disconnected and the Bluetooth device is connected. yy When you connect Bluetooth device (iOS device etc.) to this unit or operate the device, the volume level can be synchronized with each other. 3 Operating ,,Note 21 22 Operating Pairing your unit and Bluetooth device through NFC Tag About NFC Tag Connect to the Bluetooth by using the Bluetooth devices that support NFC(Near Field Communication) . 1. Activate the NFC feature of your NFC-enabled phone. 2. Turn on the unit. 3 3. Tag the back of your NFC-enabled phone over the unit. ,,Note yy Please use a device which has the NFC feature. yy NFC Recognition area may be different depending on the type of Bluetooth device. Please check the position of NFC recognition area of the Bluetooth device before tagging. yy If the screen of the Bluetooth device is locked, the device may not recognize the NFC Tag. yy In some cases, the device may not recognize the NFC. Operating -- When the case of the Bluetooth devices is chrome-plated material. -- According to the material and thickness of the case on the Bluetooth device. -- According to the performance of the NFC of the Bluetooth devices. yy Android O/S : Ver 4.1.2 (or later) yy You must activate the NFC feature of your NFC-enabled phone. 4. “PAIRED” is displayed on the unit if Bluetooth pairing is successful. 5. You can listen to music played on this unit using your Bluetooth device. Operating 23 Using the Music Flow Bluetooth App ,,Note Only Android OS is available to use “Music Flow Bluetooth” app with this unit. About “Music Flow Bluetooth” App “Music Flow Bluetooth” app brings a suite of new features to this unit. Install “Music Flow Bluetooth” App onto Your Bluetooth Device There are two ways to install “Music Flow Bluetooth” App onto Your Bluetooth Device. Install “Music Flow Bluetooth” App through QR code 1. Install “Music Flow Bluetooth” app through QR code. Use the scanning software to scan the QR code. 2. Tap an icon for installation. 3. Tap an icon for downloading. ,,Note yy Make sure that your Bluetooth device is connected to the Internet. yy Make sure that your Bluetooth device has a scanning software application. If you don’t have one, download one from “Google Android Market (Google Play Store)”. yy Depending on the area, QR code may not work. 1. Tap the “Google Android Market (Google Play Store)” icon. 2. In the search bar, type in the “Music Flow Bluetooth” and search it. 3. In the search result list, find and tap “Music Flow Bluetooth” to start downloading Bluetooth app. 4. Tap an icon for installation. 5. Tap an icon for downloading. ,,Note yy Make sure that your Bluetooth device is connected to the Internet. 3 yy Make sure that your Bluetooth device is equipped with “Google Android Market (Google Play Store)”. Operating To enjoy more features, you are recommended to download and install free “Music Flow Bluetooth” app. Install “Music Flow Bluetooth” App through “Google Android Market (Google Play Store)” 24 Operating Activate Bluetooth with “Music Flow Bluetooth” App “Music Flow Bluetooth” app helps to connect your bluetooth device to this unit. -- Android O/S : Ver 4.0.3 (or later) 2. Tap [Menu] and select the unit you want. yy If you use “Music Flow Bluetooth ” app for operation, there would be some differences between “Music Flow Bluetooth ” app and the supplied remote control. Use the supplied remote control as necessary. 3. If you want to get more information to operate, tap [Setting] and turn on the User guide. yy Depending on the Bluetooth device, “Music Flow Bluetooth ” app may not work. 1. Tap “Music Flow Bluetooth” app icon on the home screen to open “Music Flow Bluetooth” app, and go to the main menu. 3 ,,Note yy “Music Flow Bluetooth ” app will be available in the software version as follow; yy After connection of “Music Flow Bluetooth ” app, music may be output from your device. In this case, try connecting procedure again. Operating yy If you operate the other applications or change the settings on your Bluetooth device while using “Music Flow Bluetooth ” app, “Music Flow Bluetooth ” app may operate abnormally. yy When “Music Flow Bluetooth ” app operates abnormally, check your Bluetooth device and the connection of “Music Flow Bluetooth ” app and then try to connect again. yy Depending on the smart phone's operating system, you have some differences for “Music Flow Bluetooth ” operation. yy Check Bluetooth setting on your Bluetooth device if “Music Flow Bluetooth ” app connection does not work well. Operating 25 Radio Operations Presetting the Radio Stations Be sure that FM antenna is connected. (Refer to page 15) Before tuning, make sure to turn down the volume. Listening to the radio 1.Press FUNCTION until FM appears in the display window. The last received station is tuned in. You can preset 50 stations for FM. 1.Press FUNCTION until FM appears in the display window. 2. Select the desired frequency by pressing TUNING -/+ on the remote control or Y/U on the unit. 3.Press PROGRAM/MEMORY on the remote control. A preset number will blink in the display window. 5.Press PROGRAM/MEMORY on the remote control. The station is stored. Or 6. Repeat steps 2 to 5 to store other stations. Manual tuning : Press TUNING-/+ on the remote control or Y/U on the unit repeatedly. 3. Adjust the volume by rotating volume knob on the unit or by pressing VOL +/- on the remote control repeatedly. Improving poor FM reception Press T on the unit or d/M on the remote control. This will change the tuner from stereo to mono and usually improve the reception. 4.Press PRESET.FOLDER W/S on the remote control to select the preset number you want. 7. To listen a preset station, press PRESET.FOLDER W/S or 0 to 9 numerical buttons on the remote control. Deleting all the saved stations 1. Press and hold PROGRAM/MEMORY on the remote control for two seconds. “ERASEALL” will flash up on the unit display. 2.Press PROGRAM/MEMORY on the remote control to erase all the saved radio stations. 3 Operating 2. Auto tuning : Press and hold TUNING-/+ on the remote control or Y/U on the unit for about two seconds until the frequency indication starts to change, then release. Scanning stops when the unit tunes in a station. 26 Operating Seeing information about a Radio station The FM tuner is supplied with the RDS (Radio Data System) facility. This shows information about the radio station being listened to. Press RDS/SET on the remote control repeatedly to cycle through the various data types: PS (Programme Service Name) The name of the channel will appear in the display. PTY (Programme Type Recognition) The programme type (e.g. Jazz or News) will appear in the display. 3 Operating RT (Radio Text) A text message contains special information from the broadcast station. This text may scroll across the display. CT (Time controlled by the channel) This shows the time as broadcast by the station. You can search the radio stations by programme type by pressing RDS/SET on the remote control. The display will show the last PTY in use. Press PTY one or more times to select your preferred programme type. Press and hold C/V. The tuner will search automatically. When a station is found the search will stop. Operating 27 Sound adjustment Setting the sound mode This system has a number of pre-set surround sound fields. You can select a sound mode you want by using SOUND EFFECT on the remote control. The displayed items for the Equalizer may be different depending on sound sources and effects. On Display Description NATURAL You can enjoy comfortable and natural sound. Regionally optimized sound effect. (FORRO/FUNK/SERTANEJ/ DANGDUT/ARABIC/PERSIAN/ INDIA/REGUETON/MERENGUE/ SALSA/SAMBA/CUMBIA/AFRO/ AXE/TECNO BR) AUTO EQ Realizes the sound equalizer that is the most similar to the genre of which is included in the MP3 ID3 tag of song files. POP CLASSIC JAZZ ROCK This program lends an enthusiastic atmosphere to the sound, giving you the feeling you are at an actual rock, pop, jazz or classic concert. BASS Reinforces the treble, bass and surround sound effect. FOOTBALL You can enjoy the sound effect FOOTBALL STADIUM. FLAT Provides balanced sound. BOOST Boosts the mid-range for sound reinforcement. TRE/BASS Reinforces the treble and bass. STANDARD You can enjoy optimized sound. yy Maybe you need to reset the sound mode, after switching the input, sometimes even after the sound track/file changed. yy By pressing BASS BLAST on the unit you can directly select STANDARD or BASS effect. Setting the USER EQ You can adjust the sound level of Bass and Treble as your preference. 1. Press USER EQ on the unit. “USER EQ” is displayed. 2.Rotate BASS or TREBLE to adjust the sound level. 3.Press USER EQ to save the setting. 3 Operating Local Specialization equalizer (Optional) ,,Note yy On some speakers, sound may not be heard or heard in low sound depending on the sound mode. 28 Operating Advanced Operations To select recording bit rate and speed 1. Press and hold USB REC for 3 seconds. Recording to USB You can record a various sound source to USB. (CD, AUX, PORTABLE, Tuner, USB) 1. Connect the USB device to the unit. 2.Press FUNCTION to select a Function you want to record. 3 Operating One track/file recording - You can record to USB after playing a track/file you want. All tracks/files recording - You can record to USB in full stop status. Programmed list recording - After showing the Programmed list, you can record it to USB. (Refer to page 30) 3. Start the recording by pressing USB REC. -If you connect both USB1 and USB2, press USB REC when USB1 or USB2 which you want to record blinks in the display window. 4. To stop recording, press I on the unit or Z ENTER on the remote control. Pausing recording During recording, press T on the unit or d/M on the remote control to pause recording. Press it again to restart recording. (Tuner/AUX/PORTABLE only) 2.Press C/V on the remote control or Y/U on the unit to select a bit rate. 3. Press USB REC to set. 4.Press C/V on the remote control or Y/U on the unit to select a desired recording speed. (AUDIO CD only) X1 SPEED - You can listen to music while recording it. X2 SPEED - You can just record the music file. 5. Press USB REC to finish the setting. USB Copying You can copy audio files in USB 1 to USB 2. 1. Connect a USB device including desired sound files to USB port (1) and select USB 1 Function. 2. Connect another USB device to USB port (2). 3. Press USB REC to start recording. 4. To stop recording, press I on the unit or Z ENTER on the remote control. The making of unauthorized copies of copyprotected material, including computer programs, files, broadcasts and sound recordings, may be an infringement of copyrights and constitute a criminal offense. This equipment should not be used for such purposes. Be responsible Respect copyrights Operating 29 ,,Note yy You can check the recording percentage rate for the USB record on the display window during the recording. (MP3/WMA, CD Only) yy During recording MP3/WMA, there is no sound. yy For stable recording, the output sound level goes down on its own when you record music from CD to USB. yy You can only change volume level between MIN and 30 during recording. (Only CD function) yy You can control recorded MIC sound according to MIC volume. yy You may not store more than 2000 files. yy You can not record in AUTO DJ mode. yy On CD function, sound of MIC, SCRATCH or DJ EFFECT is recorded only during AUDIO CD X1 speed REC. It is recorded AUDIO CD source too. yy In case of the unsupported MP3/WMA file, the file recording may be stopped. yy It’ll be stored as follows. yy Do not remove the USB device or turn off the unit during USB recording. If does not, an incomplete file may be made and not deleted on PC. AUDIO CD MP3/WMA yy If USB recording does not work, the message like “NO USB”, “ERROR”, “USB FULL” or “NO REC” is displayed on the display window. The other source* Tuner yy Multi card reader device or External HDD can not be used for USB recording. yy A file is recorded by about 512 Mbyte when you record for a long term. * : AUX and the like. Tuner : The current recording frequency is shown. 3 Operating yy When you stop recording during playback, the file that has been recorded at that time will be stored. (Except MP3/WMA files) ,,Note yy You can record various sound using DJ EFFECT, SCRATCH or MIC. (Except USB Copying) 30 Operating Programmed Playback Deleting Programmed list The program function enables you to store your favorite files from any disc or USB device. Deleting function only works in the edit mode. A program can contain 20 tracks/files for each media. (CD, USB1,USB2) Possible to save a total of 60 tracks/files. Making Programmed list It is supported only on stop status. 1.Press PROGRAM/MEMORY on the remote control. 2.Press C/V on the remote control to select a track/file. 3 Operating 3.Press PROGRAM/MEMORY on the remote control to save and select a next track/file. 4. Repeat steps 2 - 3 to store other tracks/files. (You can modify the list by pressing PRESET.FOLDER W/S on the remote control to select the program number.) 5.Press PROGRAM/MEMORY on the remote control once again. To play the programmed list, press d/M after you make the list. ,,Note When making or modifying the programmed list, REPEAT mode is off. 1.Press PROGRAM/MEMORY on the remote control in stop status. 2. Select a song by pressing PROGRAM/MEMORY or PRESET.FOLDER W/S on the remote control repeatedly. 3.Press DELETE while a song is selected. ,,Note yy Program is switched off in the case below. -- Changing to a different function. -- Turning off and on the unit. -- Operating the numeric buttons on the remote control. yy Programmed list is cleared in the case below. -- Removing the disc or the USB device. -- Deleting or recording music files in the USB device. -- Unplugging the Power Cord. Operating Other Operations Turn off the sound temporarily Press MUTE@ on the remote control to mute your sound. You can mute your unit, for example, to answer the telephone, the “MUTE” will appear in the display window. To cancel it, press MUTE@ again or change the volume level. CHILDSAFE Mode To turn on CHILDSAFE mode, press and hold ENTER on the unit when the volume of the unit is “MIN”. In CHILDSAFE mode, the volume increase gradually. To turn off CHILDSAFE mode, press and hold ENTER on the unit when the volume of the unit is “MIN” and this mode is turned on. ,,Note In case of CD, USB or BT function, CHILDSAFE mode does not work after about 2 minutes from power on the unit even if this mode is enabled. Displaying file information (ID3 TAG) While playing an MP3 file containing file information, you can display the information by pressing INFO. DEMO In the power off state, press X-BOOM PLUS/DEMO on the unit once. The unit will power on and display the each of functions with demo sound in the display window. To cancel the DEMO function, press X-BOOM PLUS/DEMO once more. ,,Note yy While in DEMO, this unit will keep DEMO status even if you unplug the power cord connection. yy You can enjoy other functions during the DEMO, the DEMO will temporarily pause. - Without input key in 10 sec, the DEMO will play back automatically. 3 Operating This function helps to prevent you from being surprised when you turn on the unit in case that the volume of the unit is set at a high level. 31 32 Operating Using Microphone 1. Connect your microphone to the MIC jack. 2. Play the music you want. 3. Sing along with the accompaniment. Adjust the microphone volume by rotating MIC VOL. clockwise or counterclockwise on the unit. ,,Note yy When not using the microphone, set the MIC VOL. to minimum or turn off the MIC and remove the microphone from the MIC jack. yy If the microphone is set too near the speaker, a howling sound may be produced. In this case, move the microphone away from the speaker or decrease the sound level by using the MIC VOL.. 3 Operating yy If sound through the microphone is extremely loud, it may be distorted. In this case, rotate MIC VOL. to minimum. LIGHTING The function is to create a Club like atmosphere by operating speaker lighting. 1.Press LIGHTING on the unit. The mode changes each time you press it : OFF VOLCANO POLICE THUNDER PSYCHE CAOS OFF ,,Note yy Lighting function is available in all functions. yy Lighting mode retains its previous mode when you first press LIGHTING, press again to change modes. Operating 33 Setting the Clock 1. Turn the unit on. Using your player as an alarm clock 2. Press and hold CLOCK. 1. Turn the unit on. 3. Select time mode by pressing C/V on the remote control. 2. Press and hold ALARM. - AM 12:00 (for an AM and PM display) or 0:00 (for a 24 hour display) 4.Press RDS/SET to confirm your selection. 5. Select the hours by pressing C/V on the remote control. 6.Press RDS/SET. 7. Select the minutes by pressing C/V on the remote control. Setting the Clock through “Music Flow Bluetooth” App Install “Music Flow Bluetooth” app on your Android device. (Refer to page 23) Your unit’s clock will be automatically synchronized with your device by activating Bluetooth connection through “Music Flow Bluetooth” app. 4. Press C/V on the remote control to select function and press RDS/SET to save. - Press C/V on the remote control to select a memory No. when you select Tuner and then, press RDS/SET. If there is no memory No., this step is skipped. 5. Press C/V on the remote control to change the volume and press RDS/SET to save. The clock icon “(” shows that the alarm is set. ,,Note yy If you set the clock time, you can check the time by pressing CLOCK even when the player is turned off. yy You can set alarm after you set the clock time. yy If you set the clock time and alarm, you can check the alarm icon “(“ by pressing CLOCK even when the unit is turned off. yy If you set the clock time and alarm, you can check the alarm icon “(“ and setting informaiton by pressing ALARM even when the unit is turned off. yy You can select ALARM ON/OFF mode by pressing ALARM. 3 Operating 8.Press RDS/SET. 3. Press C/V on the remote control to change the hours and minutes and press RDS/ SET to save. 34 Operating Sleep Timer Setting Press SLEEP repeatedly to select delay time between 10 and 180 minutes. After the delay time, the unit will be turned off. To cancel the sleep function, press SLEEP repeatedly until “SLEEP 10” appears, and then press SLEEP once again while “SLEEP 10” is displayed. ,,Note yy You can check the remaining time before the unit is turned off. yy Press SLEEP. The remaining time appears in the display window. 3 Operating Dimmer Press SLEEP once. The display window will be darkened by half. To cancel it, press SLEEP repeatedly until dim off. ,,Note yy All the LED turns off when Dimmer is being operated. Auto power down This unit will turn itself off to save electricity in the case were the main unit is not connected to an external device and is not used for 20 minutes. The unit will also turn itself off after six hours if the Main unit has been connected to another device using the analog inputs. How to disconnect the wireless network connection or the wireless device. Turn off the unit by pressing the power button for more than 5 seconds. Operating 35 AUTO POWER On Auto function change This unit automatically turns on by an input source : LG TV or Bluetooth This unit recognizes input signals such as Bluetooth and LG TV and then changes suitable function automatically. If you try to connect your Bluetooth device, this unit turns on and connects your Bluetooth device. You can play your music. ,,Note yy Depending on the connected device, this function may not operate. yy Depending on the connected device, the unit turns on but Bluetooth function may not be connected. yy If you try to connect to the “Music Flow Bluetooth” app, Bluetooth function of this unit is turned on. yy If you turn on the unit using LG TV or Bluetooth function, proper function of this unit is turned on. yy If you have already paired with this unit, automatically this unit can turn on by an input source when this unit is turned off. yy If you turn off the unit by pressing the power button for more than 5 seconds, Auto Power On function is disabled. To activate it, turn on the unit. When you try to connect your Bluetooth device to this unit, Bluetooth function is selected. Play your music on the Bluetooth device. When LG TV is connected When you turn on your LG TV connected by LG Sound Sync, this unit changes the function to LG TV. You can hear the sound from your TV. ,,Note yy This function is not available during recording or deleting. yy This function only works with devices that were previously connected. 3 Operating yy If you disconnect Bluetooth connection by this unit, some Bluetooth devices try to connect to the unit continually. Therefore it is recommended to disconnect the connection before turning off the unit. When you try to connect Bluetooth device 36 Operating LG Sound Sync You can control some functions of this unit by your TV’s remote control with LG Sound Sync. It is compatible with LG TV that supports LG Sound Sync. Make sure your TV has the LG Sound Sync logo. Controllable function by LG TV’s remote control : Volume up/down, mute 3 Refer to the TV’s instruction manual for the details of LG Sound Sync. Operating ,,Note yy You can also use the remote control of this unit while using LG Sound Sync. If you use TV’s remote control again, the unit synchronizes with the TV. yy If the connection fails, check the conditions of this unit and your TV : power, function. yy Make sure of the condition of this unit and the connection in the cases below when using LG Sound Sync. -- Turn off the unit. -- Changing to a different function. -- Disconnecting the wireless connection caused by interference or a distance. yy The amount of time to turn off this unit is different depending on your TV. yy If you try to change the function on using the LG TV function, volume will be change according to the LG TV volume level. yy Details of TV setting menu vary depending on the manufacturers or models of your TV. yy If you connect LG Sound Sync when “Music Flow Bluetooth” app is connected, control through the app is available. yy If you turned off the unit directly by pressing 1/!(Power), LG Sound Sync will be disconnected. To use this function again, you should reconnect the TV and the unit. yy If an LG TV is connected when using Bluetooth, Bluetooth is disconnected and the LG TV is connected. 1. Turn on the unit by pressing 1/!(Power). 2. Press FUNCTION until LG TV function is selected. 3. Set up the sound output of TV to listen to the sound through this unit : TV setting menu [Sound] -> [TV Sound output] -> [LG Sound Sync (Wireless)] “PAIRED” appears on the display window for about 3 seconds and then you can see “LG TV” on the display window if the TV and this unit are connected normally. Troubleshooting 37 Troubleshooting General Problem Cause & Solution yy Turn off the power of this unit and the connected external device (TV, Woofer, DVD-player, Amplifier, etc.) and turn it on again. The unit does not work properly. yy Disconnect the power cord of this unit and the connected external device (TV, Woofer, DVD-player, Amplifier, etc.) and then try connecting again. yy Previous setting may not be saved when device power is shut off. yy The power cord is not plugged in. Plug in the power cord. No Power. No sound. yy Check whether electricity failed. Check the condition by operating other electronic devices. yy Check whether you select right function. Press FUNCTION and check the selected function. yy An unplayable disc is inserted. Check the playable disc. The unit does not start playback. yy No disc is inserted. Insert a disc. yy The disc is dirty. Clean the disc. (Refer to page 41) yy The disc is inserted upside down. Place the disc with the label or printed side facing upwards. yy The antenna is positioned or connected poorly. Connect the antenna securely. Radio stations cannot be tuned in properly. yy The signal strength of the radio station is too weak. Tune to the station manually. yy No stations have been preset or preset stations have been cleared (when tuning by scanning preset channels). Preset some radio stations, see page 25 for details. 4 Troubleshooting yy Check to see if the Speakers are connected correctly. Speaker cables connected correctly. 38 Troubleshooting Problem Cause & Solution yy The remote control is too far from the unit. Operate the remote control within about 23 ft (7 m). The remote control does yy There is an obstacle in the path of the remote control and the unit. Remove the obstacle. not work properly. yy The batteries in the remote control are exhausted. Replace the batteries with new ones. No speaker light yy Check whether the speaker light cables are connected to the unit correctly. Connect the speaker light cables to the unit correctly. yy Check the speaker light effects by pressing LIGHTING. yy Check whether your LG TV supports LG Sound Sync. LG Sound Sync does not yy Check connection of LG Sound Sync. work. yy Check sound setting of your TV and this unit. 4 Troubleshooting Appendix 39 General specifications General Power requirements Refer to the main label. Refer to the main label. Power consumption Networked standby : 0.4 W (If all network ports are activated.) Dimensions (W x H x D) 450 mm x 160 mm x 355 mm Net Weight (Approx.) 6.5 kg Operating temperature 5 °C to 35 °C (41 °F to 95 °F) Operating humidity 60 % Bus Power Supply 5 V 0 500 mA Inputs AUX IN 2.0 Vrms (1 kHz, 0 dB), 600 Ω, RCA jack (L, R) PORT. IN 1.2 Vrms (3.5 Ø jack) MIC 27 mV Tuner 87.5 to 108.0 MHz or 87.50 to 108.00 MHz 5 Frequency Response 40 to 20000 Hz Appendix Signal-to-noise ratio 75 dB Dynamic range 80 dB FM Tuning Range CD Amplifier Total output 3000 W FRONT 500 W x 2 (4 Ω at 1 kHz) WOOFER 1000 W x 2 (8 Ω at 70 Hz) THD 25 % yy Design and specifications are subject to change without notice. 40 Appendix Speakers specifications Front speaker Type Front : 2 Way 2 Speaker Subwoofer : 1 Way 1 Speaker Impedance Front : 4 Ω Subwoofer : 8 Ω Rated Input Power Front : 500 W Subwoofer : 1000 W Max. Input power Front : 1000 W Subwoofer : 2000 W Net Dimensions (W x H x D) 414 mm x 562 mm x 376 mm Net Weight 18.3 kg yy Design and specifications are subject to change without notice. Trademarks and Licenses 5 Bluetooth® wireless technology is a system which allows radio contact between electronic devices. Appendix Connecting individual devices under Bluetooth® wireless technology does not incur any charges. A mobile phone with Bluetooth® wireless technology can be operated via the Cascade if the connection was made via Bluetooth® wireless technology. The Bluetooth® word mark and logos are owned by the Bluetooth® SIG, Inc. and any use of such marks by LG Electronics is under license. Other trademarks and trade names are those of their respective owners. Appendix Maintenance 41 Handling the Unit When shipping the unit Notes on Discs Handling Discs Never stick paper or tape on the disc. Storing Discs Please save the original shipping carton and packing materials. If you need to ship the unit, for maximum protection, re-pack the unit as it was originally packed at the factory. Keeping the exterior surfaces clean After playing, store the disc in its case. Do not expose the disc to direct sunlight or sources of heat and never leave it in a parked car exposed to direct sunlight. Do not use volatile liquids such as insecticide spray near the unit. Wiping with strong pressure may damage the surface. Do not leave rubber or plastic products in contact with the unit for a long period of time. Cleaning Discs Cleaning the unit Fingerprints and dust on the disc can cause poor picture quality and sound distortion. Before playing, clean the disc with a clean cloth. Wipe the disc from the center to out. To clean the player, use a soft, dry cloth. If the surfaces are extremely dirty, use a soft cloth lightly moistened with a mild detergent solution. Do not use strong solvents such as alcohol, benzine, or thinner, as these might damage the surface of the unit. Do not use strong solvents such as alcohol, benzine, thinner, commercially available cleaners, or anti-static spray intended for old vinyl records. Maintaining the Unit 5 Appendix The unit is a high-tech, precision device. If the optical pick-up lens and disc drive parts are dirty or worn, the picture quality could be diminished. For details, please contact your nearest authorized service center.
* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project