advertisement
Blackstar Amplification Ltd, Beckett House, 14 Billing Road, Northampton, NN1 5AW, UK
For the latest information go to: www.blackstaramps.com
Whilst the information contained herein is correct at the time of publication, due to our policy of constant improvement and development, Blackstar Amplification Ltd reserves the right to alter specifications without prior notice.
ID:15TVP and ID:30TVP
Owner’s Manual
Designed and Engineered by
Blackstar Amplification UK
IMPORTANT SAFETY INSTRUCTIONS
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings.
8. Install in accordance with the manufacturer’s instructions.
9. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
10. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.
11. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.
12. Only use attachments/accessories specified by the manufacturer.
13. Unplug this apparatus during lightning storms or when unused for long periods of time.
14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
“TO COMPLETELY DISCONNECT THIS APPARATUS FROM THE AC MAINS,
DISCONNECT THE POWER SUPPLY CORD PLUG FROM THE AC RECEPTACLE”.
“WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT
EXPOSE THIS APPARATUS TO RAIN OR MOISTURE. THE APPARATUS SHALL
NOT BE EXPOSED TO DRIPPING OR SPLASHING AND THAT OBJECTS FILLED
WITH LIQUIDS, SUCH AS VASES, SHALL NOT BE PLACED ON APPARATUS".
This symbol is intended to alert the user to the presence of important operation and maintenance (servicing) instructions in the literature accompanying the appliance.
This symbol is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
3
4
Warning!
Important safety information!
READ THE FOLLOWING INFORMATION CAREFULLY. SAVE ALL
INSTRUCTIONS FOR FUTURE REFERENCE!
Follow all warnings and instructions marked on the product!
Danger! High internal operating voltages.
Do not open the equipment case. There are no user serviceable parts in this equipment. Refer all servicing to qualified service personnel.
Clean only with a dry cloth.
Condensation can form on the inside of an amplifier if it is moved from a cold environment to a warmer location. Before switching the unit on, it is recommended that the unit be allowed to reach room temperature.
Unauthorised modification of this equipment is expressly forbidden by Blackstar
Amplification Ltd.
Never push objects of any kind into ventilation slots on the equipment casing.
Do not expose this apparatus to rain, liquids or moisture of any type.
Do not place this product on an unstable trolley, stand or table. The product may fall, causing serious damage to the product or to persons!
Do not cover or block ventilation slots or openings. This unit must only be used in a well ventilated area and never switched on when it is within a poorly ventilated space, such as a bookcase.
This product should not be placed near a source of heat such as a stove, radiator, or another heat producing amplifier.
Use only the supplied power cord which is compatible with the mains voltage supply in your area.
Power supply cords should always be handled carefully and should be replaced if damaged in any way.
Never break off the earth (ground) pin on the power supply cord.
The power supply cord should be unplugged when the unit is to be unused for long periods of time.
An apparatus with Class I construction should be connected to a mains socket outlet with a protective earthing connection.
The mains plug of the power supply cord should remain readily accessible.
Before the unit is switched on, the loudspeaker should be connected as described in the handbook using the lead recommended by the manufacturer.
Always replace damaged fuses with the correct rating and type.
Never disconnect the protective mains earth connection.
High loudspeaker levels can cause permanent hearing damage. You should therefore avoid the direct vicinity of loudspeakers operating at high levels. Wear hearing protection if continuously exposed to high levels.
If the product does not operate normally when the operating instructions are followed, then refer the product to a qualified service engineer.
The U.S. Government's Occupational Safety and Health Administration (OSHA) has specified the following permissible noise level exposures:
Duration Per Day In Hours
8
6
4
3
2
1½
1
½
¼ or less
100
102
105
110
115
Sound Level dBA, Slow Response
90
92
95
97
According to OSHA, any exposure in excess of the above permissible limits could result in some hearing loss.
Ear plug protectors in the ear canals or over the ears must be worn when operating this amplification system in order to prevent a permanent hearing loss if exposure is in excess of the limits as set forth above. To ensure against potentially dangerous exposure to high sound pressure levels, it is recommended that all persons exposed to equipment capable of producing high sound pressure levels such as this amplification system be protected by hearing protectors while this unit is in operation.
All electrical and electronic products should be disposed of separately from the municipal waste stream via designated collection facilities appointed by the government or the local authorities.
5
6
Introduction
Thank you for purchasing this Blackstar ID:Series amplifier. Like all our products, this amp is the result of countless hours of painstaking Research and Development by our world-class design team. Based in Northampton (UK), the Blackstar team are all experienced musicians themselves and the sole aim of the development process is to provide guitarists with products which are the ultimate tools for self-expression.
All Blackstar products are subjected to extensive laboratory and road testing to ensure that they are truly uncompromising in terms of reliability, quality and above all TONE.
The ID:Series represents a truly ground-breaking achievement, combining unique innovations, an intuitive, traditional control set and the versatility of programmability.
Please read through this handbook carefully to ensure you get the maximum benefit from your new Blackstar product.
If you like what you hear and want to find out more about the Blackstar range of products please visit our website at www.blackstaramps.com.
Thanks!
The Blackstar Team
Features
In the five years since its launch, Blackstar has led the way in the innovation of guitar amplification. The ID:Series represents the culmination of more than seven years’ technical research and development. These amps have an intuitive control set like a traditional amp, but have the versatility of programmability. The unique controls allow you, the guitarist, to custom design your own sound, store it and then have the confidence that the amp will perform in a live environment.
Blackstar’s patent-applied-for True Valve Power offers six distinctly different power valve responses – EL84, 6V6, EL34, KT66, 6L6, KT88. When engaged it delivers the response, dynamics, sag and break up characteristics of a valve amp and uniquely delivers the same acoustic power output as an equivalent valve power amp. This means these amps deliver live without compromise – True Valve Power means
LOUD as valve TM .
The Voice control has six different settings – Clean Warm, Clean Bright, Crunch,
Super Crunch, OD 1, OD 2. When used together with Blackstar’s patented ISF control you can get the exact tone you’re thinking of.
The effects section delivers studio quality modulation, delay and reverb effects simultaneously that you can store with your sound.
Deep editing and storing of patches is simple using the Blackstar INSIDER software.
Patches can be shared, uploaded and downloaded via the online community. The
USB connector also allows you to record from your amp directly to your computer.
An emulated output and MP3/line input complete the package.
By using the unique Voice control, the patented ISF and patent-applied-for True
Valve Power, ID amplifiers allow unparalleled flexibility and ease of use, enabling you to, in effect, design the sound in your head and deliver it live as LOUD as valve TM .
Individuality is power!
7
8
Demo Mode
When the amplifier is first switched on after purchase, or after a factory reset, it will be in ‘Demo Mode’. The sound you hear will reflect the physical position of the front panel knobs as it will be in Manual Mode. All effects, plus TVP will be turned off.
All amplifier patch locations will contain Blackstar factory defaults. Patches can be created and stored in Demo Mode but the original factory default patches and settings will be restored each time the amplifier is turned off and turned on again.
To exit Demo Mode, hold down the Manual button (19) while switching the amplifier on. The Bank LED (20) will change from red, to orange, to green and then turn off to indicate that Demo Mode has been deactivated. If the Manual button is released before the Bank LED has cycled through all colours and switched off, then the operation is cancelled and the amplifier will remain in Demo Mode.
Blackstar’s INSIDER software can also be used to exit Demo Mode. From within the program, right click on the Demo Mode label and select ‘Disable’.
Factory Reset
The default factory patches and settings can be restored to your amplifier at any time. Simply hold down the MOD, DLY and REV buttons simultaneously, whilst switching on the amplifier. The bank LED will illuminate, and change from green, to orange, to red, to indicate that a factory reset is imminent. This process will take a total of two seconds. If any of the MOD, DLY and REV buttons are released before the bank LED has cycled through all colours and switched off, then the operation is cancelled and the amplifier will remain unaffected.
Once this is complete the amplifier will be in Demo Mode again.
IMPORTANT NOTE: This process will overwrite any user saved patches and settings.
9
10
Front Panel
1. Input
Plug your guitar in here. Always use a good quality screened guitar lead.
2. Voice
The Voice control changes the preamp voicing, ranging from ultra clean to extremely overdriven.
Clean Warm – Very clean, dynamic
Clean Bright – ‘Boutique’, will break up when pushed hard
Crunch – Classic medium gain overdrive
Super Crunch – More gain and punch than Crunch
OD 1 – Hot-rodded Master Volume overdrive
OD 2 – Mid boosted hot-rod overdrive
This setting is saved when you store a patch.
3. Gain
The Gain control adjusts the amount of overdrive or distortion. Low settings (counter clockwise) will deliver a clean sound on the edge of break-up. As the Gain control is turned clockwise the sound will become more overdriven, moving through beautiful crunch tones until, at its maximum position, a full distorted tone is achieved. This setting is saved when you store a patch.
4. Volume
This controls the preamp volume. Turning it clockwise increases the volume.
High levels of volume will introduce the effect of valve power amp distortion and compression, depending on the TVP (8) setting you have selected. This setting is saved when you store a patch.
5. Bass
The bass control adjusts the amount of low-end frequencies in your tone. This amp has an advanced tone shaping circuit which allows the tone to be tight and cutting
(counter clockwise) to warm and thumping (clockwise). This setting is saved when you store a patch.
6. Treble
The treble control allows exact adjustment of the treble frequencies within the sound.
At low settings (counter clockwise) the sound will be warm and dark in character.
As the treble control is increased (clockwise) the sound will become brighter. At the maximum settings the sound will be aggressive and cutting. This setting is saved when you store a patch.
EL84
6V6
EL34
KT66
6L6
KT88
7. ISF
The patented ISF control works in conjunction with the Bass and Treble controls. It allows you to choose the exact tonal signature you prefer. Fully counter clockwise has a more American characteristic with a tight bottom-end and more aggressive middle, and fully clockwise has a British characteristic which is more ‘woody’ and less aggressive.
USA UK
Unlike conventional ‘contour’ controls and parametric equalisation systems, the Bass and Treble controls remain interactive with each other just like in a traditional guitar amplifier tone stack. This leads to a very familiar, musical response. This setting is saved when you store a patch.
8. TVP (True Valve Power) Selector
Blackstar’s patent-applied-for True Valve Power offers six distinctly different power valve responses – EL84, 6V6, EL34, KT66, 6L6 and KT88. When engaged it delivers the response, dynamics, sag and break-up characteristics of a valve amp and uniquely delivers the same acoustic power output as an equivalent valve power amp. This means that these amps deliver live without compromise – True Valve
Power means LOUD as Valve TM .
TVP changes the characteristics of the sound from compressed and spongy to dynamic and tight.
Bell-like full bodied Class A with lots of compression
Crisp Class A with high compression and tight mids
Classic British Class A/B crunch with full bodied soft break-up
Rich and warm vintage British hot biased Class A/B
Tight dynamic Class A/B with extended high and lows
Tight, bold and dynamic Class A/B with strong low end
As you move from EL84 to KT88 the amount of compression and overdrive available from each valve response is reduced. Additionally, when either of the two clean voices is selected the output compression and overdrive are affected by the gain control.
This setting is saved when you store a patch.
9. TVP (True Valve Power) Switch
Pressing this switch turns TVP on and off. The internal button LED will light to show
TVP is on. When the LED is off, TVP is not active and the TVP Selector will be deactivated. This setting is saved in a patch.
NOTE: With TVP off the power amplifier has a linear response and you will not be able to achieve the valve-like sag, compression and power that TVP delivers.
Effects
Up to three studio quality effects can be switched on at any time.
11
12
10. MOD (Modulation)
Press this switch to turn the modulation effect on, off, or focus the effect for editing.
This setting is saved when you store a patch.
11. DLY (Delay)
Press this switch to turn the delay effect on, off, or focus the effect for editing. This setting is saved when you store a patch.
12. REV (Reverb)
Press this switch to turn the reverb effect on, off, or focus the effect for editing. This setting is saved when you store a patch.
With all three of the effect switches the LED will show what state it is in:
LED
LED not on
LED red
LED green
Effect State
Effect off
Effect on but not ‘focused’ for editing
Effect on and ‘focused’ for editing
Description
Effect not active
Effect is active, but not affected by the front panel effect controls
Effect active and affected by the front panel effect controls
Repeatedly pressing each effect switch on the front panel has the following effect:
Effect off
Effect on but not ‘focused’
Effect on and ‘focused’
Turns the effect on and ‘focuses’ the effect. Any previously focused effect reverts to an ‘on’ state
Focuses the effect. Any previously focused effect reverts to an ‘on’ state
Turns the effect off. If any other effect(s) are on, the previously ‘focused’ effect resumes being ‘focused’
NOTE: Only one effect may be ‘focused’ at any time
13. Effect Type
This changes the effect type and edits a parameter of the currently ‘focused’ effect
(modulation, delay, or reverb).
Each segment represents a different effect (four for each type of effect). An
LED shows which effect type is currently active. The distance travelled through the ‘segment’ modifies an effect parameter. The Effects Table below shows the modifiable parameters:
This setting is saved when you store a patch.
14. Effect Level
This modifies an effect parameter. For modulation and delay effects, turning the Level control while holding down the Tap button (15) modifies the rate/time of the effect.
The Effects Table below shows the modifiable parameters:
This setting is saved when you store a patch.
15. Tap
The Tap button is used to set the rate/time of the current ‘focused’ effect. The time between each press of the tap button defines the rate set.
Once set, the Tap LED will flash in time with the set rate of the currently ‘focused’ effect.
The Effects Table below shows the modifiable parameters:
Effects Table
Effect Segment Parameter Level Parameter Tap Parameter
MODULATION
Phaser
Flanger
Chorus
Tremolo
DELAY
Linear
Analogue
Tape
Multi
REVERB
Room
Hall
Spring
Plate
Size
Size
Size
Size
Mix
Feedback
Mix
Frequency modulation depth
Feedback
Feedback
Feedback
Feedback
Depth
Depth
Depth
Amplitude modulation depth
Delay level
Delay level
Delay level
Delay level
Reverb level
Reverb level
Reverb level
Reverb level
This setting is saved when you store a patch.
-
-
-
-
Time
Time
Time
Time
Speed
Speed
Speed
Speed
16. Master Volume
This controls the overall volume of your amplifier. Turning it clockwise increases the volume. This is a global setting and not saved when storing a patch.
If the master volume is at zero this allows for silent recording via the emulated output or USB. The emulated level is controlled via the preamp volume.
17. Power Switch
This switch is used to turn the amplifier on and off, the white dot means the amplifier is on.
NOTE: when in Demo Mode powering the amplifier off and then on restores the factory default settings. When not in Demo Mode, the amplifier will retain its state when powered back up.
13
14
18. USB
Plug a USB cable in here to connect the amplifier to a Windows PC or Mac.
Blackstar’s INSIDER software can be downloaded from our website and offers a host of features.
See the USB Audio section on page 20 for more information.
NOTE: The amplifier will appear on a personal computer as an audio capture device within recording software.
19. Manual
Press this switch to toggle between Manual Mode and the current patch. When the amplifier is in Manual Mode, the sound will reflect the current physical position of the knobs. This is applicable to the Voice, Gain, Volume, Bass, Treble, ISF and TVP knobs. The TVP on/off state will be retained from the previously active patch. Any effects that are active when switching to Manual Mode will be turned off.
While in Manual Mode any of the controls can still be modified by an external source
(Blackstar INSIDER software, footswitch, MIDI controller), but this means that the sound will not represent the positions of the knobs on the front panel.
Tuner Mode
Holding the Manual button (19) for three seconds will engage the tuner. The Recall
Indicator LED (28) will flash continuously to indicate the amplifier is in Tuner Mode.
By default the amplifier ouput will be muted whilst in Tuner Mode.
The Manual, Bank and Channel LEDs will indicate the closest note to the note being played.
Bank LED
CH1 LED
CH2 LED
CH3 LED
CH4 LED
String 1 and 6 (default E, low/high)
String 2
String 3
String 4
String 5
The MOD, DLY and REV LEDs act as indicators to show how close the played note is to the tuned note.
MOD LED red
DLY LED green
REV LED red
Note is sharp (above pitch)
Note is in tune
Note is flat (below pitch)
All other LEDs on the front panel will be off in Tuner Mode.
Pressing any button will exit Tuner Mode.
20. Bank
Press the button to scroll through the first three banks of patches.
Bank 1 2
Bank 2 3
Bank 3 1
The green LED indicates you’re in Bank 1, the orange LED indicates you’re in Bank
2 and the red LED indicates you’re in Bank 3.
NOTE: The first three banks can be selected from the front panel. When you activate
Bank 4 and higher from an external controller (e.g. Blackstar INSIDER software, footcontroller), the Bank LED will not be lit but the channel LEDs will continue to show you the patch location.
For example:
Patch 11 – Bank LED red, Channel 3 LED lit.
Selecting Bank 15 from an external controller will switch you to patch 15 – Bank
LED off, Channel 3 lit.
When the amplifier is in Manual Mode, the Bank LED will not be lit.
The channel will be remembered, therefore the corresponding patch within the current bank will be loaded when scrolling through the banks.
21 – 24. Channels 1-4
Channel 1 activates the first patch within the currently active bank.
Channel 2 activates the second patch within the currently active bank.
Channel 3 activates the third patch within the currently active bank.
Channel 4 activates the fourth patch within the currently active bank.
25. Footswitch
Connect one of the following supported footswitches here.
1 button footswitch
Use any latching footswitch (e.g. a Blackstar FS-4) to switch between Channels 1 and 2 of the currently selected Bank.
Footswitch latched OFF (e.g. LED extinguished on the FS-4) activates Channel 1
Footswitch latched ON (e.g. LED illuminated on the FS-4) activates Channel 2
Blackstar FS-10 Footcontroller
This multi function footcontroller allows you to access all patches, toggle effects and program patches.
15
16
26. MP3/Line In
Connect the output of your mp3 or CD player here. Adjust the player’s volume to match that of your guitar to enable you to play along.
NOTE: The connection is stereo summed into mono.
27. Emulated Output/Headphone Out
This output emulates the tonal characteristics of a guitar speaker cabinet and provides a natural tone for connection to a recording device or mixing desk.
To make full use of the stereo effects, use a stereo jack to two mono jacks splitter lead to feed two channels of the recording device or mixer. The output will also function into a mono guitar type lead. Always use a good quality screened lead.
Turning the Volume knob (4) will control the Emulated Output level. The Master
Volume only affects any connected speaker(s)/cabinet(s).
NOTE: To ‘silently’ record, set the Master Volume to zero. You may also record from this output without a loudspeaker connected, but ensure that no loudspeaker leads are connected to any of the loudspeaker output jack sockets of the amplifier, as this will defeat the load protection circuit and will cause damage to the amplifier.
28. Recall Indicator
The Recall Indicator shows if there is a mismatch between the current value of a parameter within the amplifier and the corresponding physical front panel control.
E.g. when you change to a different patch the controls on the front panel may not always reflect the setting you are hearing.
To prevent unexpected level jumps in the control you are adjusting, the front panel knobs will have no effect on the sound until the knob reaches the current parameter value. Once reached, the Recall Indicator flashes twice and the knob ‘takes control’ of the value and can increase or decrease the value.
The recall indicator will flash twice each time the physical knob ‘passes through’ the value stored within the current patch so you can easily see the programmed value.
Recall is only active for Gain, Volume, Bass, Treble and ISF.
When the Tuner is active the Recall Indicator will flash continuously.
Rear Panel
1. Mains Input
The supplied detachable mains lead is connected here. The lead should only be connected to a power outlet that is compatible with the voltage, power and frequency requirements stated on the rear panel. If in doubt get advice from a qualified technician.
Programmability
Storing Patches
To store the current sound as a patch
1. Press and hold any of the four Channel buttons for one second. All four
Channel LEDs will begin to flash.
2. Press the Bank button to toggle through the three banks (green, orange, red) to choose the store location.
3. Press any of the four Channel buttons once to store the patch in the chosen location.
The LED corresponding to the chosen store location will illuminate and the new patch will be active.
Green bank = Patches 1-4
Orange bank = Patches 5-8
Red bank = Patches 9-12
The amplifier controls can be used to edit the patch at any stage of the store process.
Press the Manual button at any stage to cancel the store process and return the amplifier to the last state.
Storing a patch will overwrite any previous patch in that location.
Patches can also be stored via Blackstar’s INSIDER software or a connected
Blackstar FS-10 footcontroller.
Recalling Patches
Press any Channel button to load that patch.
Pressing the Bank button will cycle through the three banks – green-orange-red.
The Channel will be preserved, therefore the corresponding patch within the current
Bank will be loaded when scrolling through the Banks.
Alternatively, patches can be recalled via Blackstar’s INSIDER software or any connected footswitch.
17
18
USB Audio
Standard audio drivers are used to connect the amplifier to a PC or Mac, no specific drivers are required.
The amplifier will appear as an audio capture device within recording software.
The output of the audio over USB can be changed via the Blackstar INSIDER software, and can be one of the following:
Speaker emulated stereo effected audio channels
2 x mono audio channels
- Left – effected amplifier signal
- Right – unprocessed guitar signal
Re-amping Mode
Re-amping
The amplifier can be switched into Re-amping Mode via Blackstar INSIDER software.
This is a non-storable setting and will be switched off either when the USB cable is removed, or when the amplifier power is switched off.
When activated, Re-amping Mode allows the amplifier to accept a pre-recorded, dry guitar signal via USB and return a fully processed audio signal. This return signal can then be captured using recording software on the connected PC or Mac.
Firmware Update
Firmware updates are initiated via Blackstar INSIDER software. A new version of the
Blackstar INSIDER software will be released whenever an update is available. Each update will take approximately 60-120 seconds.
When the amplifier is connected (via USB) to a version of the Blackstar INSIDER software containing newer firmware, a message will be displayed, prompting you to install the latest files. Whilst updating, the amplifier controls will be unresponsive.
The Tap LED will flash to indicate data activity during the update process.
The amplifier power should not be switched off during a firmware update. If the amplifier is switched off during an update, the controls will be unresponsive after the power is reapplied and the amplifier will produce no sound. The Tap LED will flash to indicate that the amplifier contains no valid firmware.
The amplifier must be connected to the Blackstar INSIDER software to reinstall valid firmware. The update process will start automatically if the Blackstar INSIDER software detects that the amplifier is in this state.
Technical Specification
ID:15TVP
Power: 15 Watts
Weight (kg): 11
Dimensions (mm): 450(W) x 417(H) x 220(D)
Footswitch (not supplied): FS-4 latching footswitch, FS-10 footcontroller
ID:30TVP
Power: 30 Watts
Weight (kg): 13
Dimensions (mm): 500(W) x 460(H) x 250(D)
Footswitch (not supplied): FS-4 latching footswitch, FS-10 footcontroller
19
20
Bitte benutzen Sie das Gerät nur in gut belüfteten Räumen und schalten Sie es nie in schlecht belüfteten Umgebungen, wie z.B. Schränken o.ä. an.
All electrical and electronic products should be disposed of separately from the municipal waste stream via designated collection facilities appointed by the government or the local authorities.
21
22
Einleitung
Vielen Dank, dass Sie sich für den Blackstar ID:Series Verstärker entschieden haben. Dieser Amp ist wie alle unsere Verstärker das Ergebnis unzähliger Stunden akribischer Arbeit durch unser erstklassiges Entwickler-Team. Blackstar hat seinen
Sitz in Northampton (UK) und setzt sich aus einem Team erfahrener Musiker zusammen, die nur ein Ziel verfolgen: Gitarristen mit den Werkzeugen zu versorgen, die ihnen dabei helfen, sich selbst zu verwirklichen.
Alle Blackstar-Produkte wurden sowohl in unseren Labors als auch im Live-Betrieb auf Herz und Nieren getestet, um sicherzustellen, dass sie in puncto Zuverlässigkeit,
Qualität und KLANG absolut kompromisslose Ergebnisse liefern.
Die ID:Series ist eine wirklich bahnbrechende Neuvorstellung, die einzigartige
Innovationen mit intuitiv-traditionellen Bedienelemente und einer vielseitigen
Programmierbarkeit kombiniert.
Bitte lesen Sie dieses Handbuch aufmerksam durch, um Ihr neues Blackstar-
Produkt optimal nutzen zu können.
Wenn Sie mehr über die Blackstar-Produktreihe erfahren möchten, besuchen Sie unsere Webseite unter www.blackstaramps.com.
Vielen Dank!
Das Blackstar-Team
Merkmale
In den 5 Jahren seit Gründung hat Blackstar sehr viel für die Innovation von
Gitarrenverstärkern getan. Die ID-Series ist nun das Ergebnis aus sieben
Jahren technischer Forschung und Entwicklung. Diese Verstärker bieten die gewohnt intuitiven Bedienelemente eines traditionellen Amps, sind aufgrund ihrer
Programmierbarkeit aber deutlich vielseitiger. Die einzigartigen Steuermöglichkeiten erlauben es Ihnen als Gitarrist, Ihren ganz persönlichen Sound zu finden, einzustellen und dann in jeder Live-Situation identisch abzurufen.
Die von Blackstar zum Patent angemeldete True Valve Power bietet sechs unterschiedliche Charakteristika von Endstufenröhren – EL84, 6V6, EL34, KT66,
6L6 und KT88. Diese Funktion sorgt für eine authentische Ansprache, Dynamik sowie das „Sag“- und das Sättigungsverhalten eines Röhren-Amps und liefert definitiv dieselbe akustische Power wie eine vergleichbare Röhren-Endstufe. Diese
Amps präsentieren sich live absolut kompromisslos – True Valve Power bedeutet:
LOUD as Valve TM .
Der Voice-Regler bietet sechs unterschiedliche Einstellungen – Clean Warm, Clean
Bright, Crunch, Super Crunch, OD 1, OD 2. In Verbindung mit dem für Blackstar patentierten ISF-Regler erzielen Sie genau den gewünschten Sound.
Die Effekt-Sektion erzeugt gleichzeitig Modulations-, Delay- und Reverb-Effekte in
Studio-Qualität, die Sie zusammen mit Ihren Sounds abspeichern können.
Mit Hilfe der mitgelieferten Blackstar INSIDER Software gestaltet sich die tief greifende Editierung ebenso wie das Speichern von Patches extrem einfach.
Patches können über die Online Community hochgeladen, heruntergeladen und ausgetauscht werden. Über den USB-Anschluss können Sie über den Amp direkt auf den Computer aufnehmen.
Ein emulierter Ausgang, ein MP3/Line-Eingang sowie eine MIDI-Umschaltung per
Fuß komplettieren das Angebot.
Dank des einzigartigen Voice-Reglers, der patentierten ISF-Schaltung sowie der zum
Patent angemeldeten True Valve Power bieten ID-Verstärker eine unvergleichliche
Flexibilität bei einfacher Bedienung, die es in Ihnen erlaubt, den Sound, den Sie sich vorstellen, live mit der LOUD as Valve TM zu realisieren. Individuality is Power!
23
24
Demo-Modus
Wenn der Verstärker zum ersten Mal in Betrieb genommen oder auf die
Werkseinstellungen zurückgesetzt wird, befindet er sich im ‚Demo-Modus’. Der
Sound, den Sie hören, entspricht – wie im Manual-Modus – den physikalischen
Reglerpositionen. Alle Effekte sowie TVP sind deaktiviert.
Alle Patch-Speicherplätze sind mit Werkseinstellungen von Blackstar belegt. Sie können Patches im Demo-Modus erzeugen und speichern, allerdings werden die ursprünglichen Werks-Patches und -Einstellungen immer wiederhergestellt, wenn der Verstärker aus- und wieder eingeschaltet wird.
Um den Demo-Modus zu verlassen, halten Sie den Taster Manual (19) gedrückt, während Sie den Verstärker einschalten. Die Bank-LED (20) wechselt von rot über orange zu grün und erlischt schließlich: Der Demo-Modus ist nun deaktiviert. Wenn
Sie den Taster Manual loslassen, bevor die Bank-LED alle Farben durchlaufen hat und erloschen ist, wird der Vorgang abgebrochen und der Verstärker arbeitet weiterhin im Demo-Modus.
Sie können den Demo-Modus auch über die Blackstar INSIDER Software beenden.
Klicken Sie innerhalb des Programms mit der rechten Maustaste auf den Eintrag
Demo Mode und wählen Sie ‚Disable’.
Factory Reset
Die Werks-Patches und -Einstellungen können im Verstärker zu jeder Zeit wiederhergestellt werden. Halten Sie die Tasten MOD, DLY und REV gleichzeitig gedrückt, während Sie den Verstärker einschalten. Die Bank-LED leuchtet und wechselt von grün über orange zu rot: Das bedeutet, dass ein Factory Reset durchgeführt wird. Dieser Vorgang dauert etwa zwei Sekunden. Wenn Sie eine der
Tasten MOD, DLY und REV loslassen, bevor die Bank-LED alle Farben durchlaufen hat und erloschen ist, wird der Vorgang abgebrochen und der Verstärker wird nicht zurückgesetzt.
Nach diesem Vorgang befindet sich der Verstärker wieder im Demo-Modus.
WICHTIGER HINWEIS: Dieser Vorgang überschreibt alle vom Anwender angelegten Daten.
25
26
Vorderseite
1. Input
Hier schließen Sie Ihre Gitarre an. Verwenden Sie in jedem Fall hochwertige geschirmte Gitarrenkabel.
2. Voice
Der Voice-Regler verändert das Preamp-Voicing im Bereich von extrem clean bis extrem übersteuert.
Clean Warm – Sehr clean, dynamisch
Clean Bright – ‚Boutique’, übersteuert bei hartem Anschlag
Crunch – Klassischer Overdrive bei mittlerem Gain
Super Crunch – Mehr Gain und Druck als Crunch
OD 1 – „Aufgebohrter“ Overdrive-Sound über das Master Volume
OD 2 – Heftiger Overdrive-Sound mit Mitten-Boost
Diese Einstellung wird beim Sichern eines Patches gespeichert.
3. Gain
Mit dem Gain-Regler steuern Sie den Grad der Übersteuerung bzw. Verzerrung.
Niedrige Einstellungen (gegen den Uhrzeigersinn) liefern einen cleanen Sound mit viel Druck und Durchsetzungsvermögen. Wenn der Gain-Regler im Uhrzeigersinn aufgedreht wird, nimmt der Verzerrungsgrad mehr und mehr zu und wechselt von crunchigen Sounds bis hin zu stark verzerrten Sounds in der Extremposition. Diese
Einstellung wird beim Sichern eines Patches gespeichert.
4. Volume
Dieser Regler steuert die Aussteuerung des Preamps. Im Uhrzeigersinn heben
Sie die Lautstärke an. Abhängig von der Einstellung für TVP (8) tritt bei höherer
Lautstärke ein Sättigungs- und Kompressionseffekt in der Röhren-Endstufe auf.
Diese Einstellung wird beim Sichern eines Patches gespeichert.
5. Bass
Der Bass-Regler steuert den Anteil der Bassfrequenzen im Gesamt-Sound. Dieser
Verstärker bietet eine umfangreiche Klangregelung, mit der Sie den Ton zwischen knackig und aggressiv (gegen den Uhrzeigersinn) oder warm und druckvoll (im
Uhrzeigersinn) einstellen können. Diese Einstellung wird beim Sichern eines Patches gespeichert.
6. Treble
Mit dem Regler Treble können Sie gezielt den Höhenanteil im Gesamt-Sound einstellen. Bei niedrigen Einstellungen (gegen den Uhrzeigersinn) erhält der Sound einen warmen und dunkleren Charakter. Wenn der Treble-Regler angehoben wird
(im Uhrzeigersinn), wird der Sound immer höhenreicher. In der Maximalposition klingt der Sound schließlich aggressiv und schneidend. Diese Einstellung wird beim
Sichern eines Patches gespeichert.
7. ISF
Der patentierte ISF-Regler arbeitet mit den Reglern für
Bass, Middle und Treble zusammen. Mit seiner Hilfe finden Sie die genau die Klangfärbung, die Sie suchen.
Bei Einstellungen gegen den Uhrzeigersinn besitzt der
Amp einen „amerikanischen“ Sound-Charakter mit einem knackigen Bassfundament und aggressiveren
Mitten. Bei Einstellungen im Uhrzeigersinn erzeugt der
Amp einen „britischen“ Sound, der deutlich erdiger und weniger aggressiv klingt.
USA UK
Im Gegensatz zu herkömmlichen ‚Contour’-Reglern und parametrischen EQ-
Systemen beeinflussen sich die Regler für Bass, Middle und Treble gegenseitig –so wie man das aus klassischen Gitarren-Stacks her kennt. Das führt letztlich zu einem vertrauten, musikalischen Verhalten. Diese Einstellung wird beim Sichern eines
Patches gespeichert.
8. TVP (True Valve Power) Wahlschalter
Die von Blackstar zum Patent angemeldete True Valve Power bietet sechs unterschiedliche Charakteristika von Endstufenröhren – EL84, 6V6, EL34, KT66,
6L6 und KT88. Diese Funktion sorgt für eine authentische Ansprache, Dynamik sowie das „Sag“- und das Sättigungsverhalten eines Röhren-Amps und liefert definitiv dieselbe akustische Power wie eine vergleichbare Röhren-Endstufe. Diese
Amps präsentieren sich live absolut kompromisslos – True Valve Power bedeutet:
LAUT wie eine Röhre TM .
TVP verändert die Klangcharakteristik – von komprimiert und druckvoll bis dynamisch und knackig.
EL84
6V6
EL34
KT66
6L6
KT88
Glockig-kräftiger Class-A-Sound mit viel Kompression
Knackiger Class-A-Sound mit starker Kompression und kräftigen Mitten
Klassischer britischer Class-A/B-Crunch mit ebenso mächtiger wie angenehmer Übersteuerung
Voller, warmer und typisch britischer Vintage-Class-A/B-Sound mit kräftigem Bias
Kraftvoller, dynamischer Class-A/B-Sound mit betonten Bässen und Höhen
Knackig-fetter und dynamischer Class-A/B-Sound mit kräftigem Bass-Fundament
Wenn Sie von EL84 auf KT88 umschalten, wird der Kompressionsgrad und die
Übersteuerungsreserve in der Röhrenansprache reduziert. Bei den beiden Clean-
Voices hängt die Ausgangskompression und -übersteuerung zudem von der
Stellung des Gain-Reglers ab.
Diese Einstellung wird beim Sichern eines Patches gespeichert.
9. TVP (True Valve Power) Taster
Mit diesem Taster (de-)aktivieren Sie TVP. Die in dem Taster integrierte LED leuchtet, wenn TVP aktiv ist. Wenn die LED nicht leuchtet, ist TVP inaktiv und der TVP-
Wahlschalter ist deaktiviert. Diese Einstellung wird mit dem Patch gespeichert.
ANMERKUNG: Wenn TVP inaktiv ist, liefert die Endstufe eine lineare Ansprache:
Röhren-typische Effekte wie das „Sag“, die Kompression und Power von TVP stehen entsprechend nicht zur Verfügung.
27
28
Effekte
Bis zu drei Effekte in Studio-Qualität können zu jeder Zeit aktiviert werden.
10. MOD (Modulation)
Mit diesem Schalter (de-)aktivieren Sie den Modulationseffekt oder wählen ihn zur
Editierung aus. Diese Einstellung wird beim Sichern eines Patches gespeichert.
11. DLY (Delay)
Mit diesem Schalter (de-)aktivieren Sie den Delay-Effekt oder wählen ihn zur
Editierung aus. Diese Einstellung wird beim Sichern eines Patches gespeichert.
12. REV (Reverb)
Mit diesem Schalter (de-)aktivieren Sie den Reverb-Effekt oder wählen ihn zur
Editierung aus. Diese Einstellung wird beim Sichern eines Patches gespeichert.
Die LEDs von allen drei Effekt-Tastern zeigen den aktuellen Status:
LED
LED inaktiv
LED rot
LED grün
Effekt-Status
Effekt aus
Effekt aktiv, aber nicht für die Editierung ausgewählt
Effekt aktiv und für die Editierung ausgewählt
Beschreibung
Effekt inaktiv
Effekt ist aktiv, wird aber nicht über die Effekt-
Regler auf der Front gesteuert
Effekt ist aktiv und wird über die Effekt-Regler gesteuert
Ein wiederholtes Drücken der Effekt-Taster auf der Vorderseite hat den folgenden
Effekt:
Effekt aus Aktiviert den Effekt und setzt den Effekt in den ‚Fokus’. Der bisherige ‚Fokus’-
Effekt wird in den Status ‚On’ geschaltet
Effekt aktiv, aber nicht im
‚Fokus’
Setzt den Effekt in den Fokus. Der bisherige ‚Fokus’-Effekt wird in den Status
‚On’ geschaltet
Effekt aktiv und im ‚Fokus’ Schaltet den Effekt aus. Wenn ein (oder mehrere) andere(r) Effekt aktiv ist, bleibt der bisherige ‚Fokus’-Effekt weiterhin im ‚Fokus’
ANMERKUNG: Es kann immer nur ein Effekt im ‚Fokus’ stehen.
13. Effekt-Type
Hier wählen Sie den Effekt-Typ und editieren einen Parameter des aktuellen ‚Fokus’-
Effekts (Modulation, Delay oder Reverb).
Jedes Segment steht für einen anderen Effekt (vier für jeden Effekt-Typ). Eine
LED zeigt, welcher Effekt-Typ momentan aktiv ist. Der Regelweg innerhalb des
‚Segments’ verändert den jeweiligen Effekt-Parameter. Die Effekt Tabelle unten listet alle einstellbaren Parameter auf:
Diese Einstellung wird beim Sichern eines Patches gespeichert.
14. Effekt-Level
Dieser Regler verändert einen Effekt-Parameter. Bei Modulations- und Delay-Effekten können Sie mit dem Level-Regler bei gehaltenem Tap-Taster (15) die Rate/Time des Effekts verändern.
Die Effekt Tabelle unten listet alle einstellbaren Parameter auf:
Diese Einstellung wird beim Sichern eines Patches gespeichert.
15. Tap
Der Tap-Taster dient zur Eingabe der Rate/Time des Effekts im aktuellen ‚Fokus’.
Die Dauer zwischen jedem Drücken des Tap-Tasters bestimmt die Rate-Einstellung.
Nach der Einstellung blinkt die Tap-LED in der Geschwindigkeit, die für den Effekt im ‚Fokus’ eingegeben wurde.
Die Effekt Tabelle unten listet alle einstellbaren Parameter auf:
Effekt Tabelle
Effekt Segment-Parameter Level-Parameter Tap-Parameter
MODULATION
Phaser
Flanger
Chorus
Tremolo
Mix
Feedback
Mix
Depth der Frequenz-
Modulation
DELAY
Linear
Analogue
Tape
Multi
REVERB
Room
Hall
Spring
Plate
Feedback
Feedback
Feedback
Feedback
Size
Size
Size
Size
Depth
Depth
Depth
Depth der Amplituden-
Modulation
Delay level
Delay level
Delay level
Delay level
Reverb level
Reverb level
Reverb level
Reverb level
Time
Time
Time
Time
-
-
-
-
Speed
Speed
Speed
Speed
Diese Einstellung wird beim Sichern eines Patches gespeichert.
29
30
16. Master Volume
Dieser Regler steuert die Gesamtlautstärke Ihres Verstärkers. Im Uhrzeigersinn heben Sie die Lautstärke an. Hierbei handelt es sich um eine globale Einstellung, die nicht in den Patches gespeichert wird.
Wenn das Master Volume auf 0 heruntergezogen ist, können Sie ohne den
Lautsprecher über den emulierten Ausgang oder über USB Aufnahmen machen.
Der Pegel der Emulation wird über das Preamp-Volume ausgesteuert.
17. Power Schalter
Mit diesem Schalter schalten Sie den Verstärker ein bzw. aus. Der weiße Punkt bedeutet, dass der Verstärker an ist.
ANMERKUNG: Wenn Sie den Verstärker aus dem Demo-Modus heraus aus- und wieder einschalten, werden die Werkseinstellungen wiederhergestellt. Wenn der
Demo-Modus nicht aktiv ist, befindet sich der Verstärker nach dem Einschalten wieder im vorher aktiven Modus.
18. USB
Hier schließen Sie ein USB-Kabel an, um den Verstärker mit einem Windows PC oder einem Mac zu verbinden. Die Blackstar INSIDER-Software kann von unserer
Webseite heruntergeladen werden und bietet zahlreiche Funktionen.
Lesen Sie dazu den Abschnitt USB Audio auf Seite 39.
ANMERKUNG: Der Verstärker erscheint innerhalb der Aufnahme-Software auf einem Computer als Audio-Interface.
19. Manual
Mit diesem Taster schalten Sie zwischen dem Manual-Modus und dem aktuellen
Patch um. Im Manual-Modus entspricht der Sound den aktuellen physikalischen
Positionen der Regler. Das gilt für die Regler Voice, Gain, Volume, Bass, Middle,
Treble, ISF und TVP. Der On/Off-Status für TVP wird vom vorher aktiven Patch
übernommen. Alle Effekte, die beim Umschalten in den Manual-Modus aktiv sind, werden abgeschaltet.
Im Manual-Modus können alle Regler weiterhin über externe Quellen (Blackstar
INSIDER Software, Fußschalter, MIDI-Controller) gesteuert werden. Das bedeutet aber, dass der Sound nicht den physikalischen Positionen der Regler auf der Front entspricht.
Tuner-Modus
Halten Sie den Manual-Taster (19) drei Sekunden gedrückt, um den Tuner zu aktivieren. Die LED der Recall-Anzeige (28) blinkt dauerhaft und zeigt so, dass der
Tuner-Modus aktiv ist. In der Voreinstellung wird der Verstärkerausgang stumm geschaltet, wenn der Tuner-Modus aktiv ist. Über die LEDs Manual, Bank und
Channel wird die Note angezeigt, die der gespielten Note am nächsten kommt.
Bank LED
CH1 LED
CH2 LED
CH3 LED
Saite 1 und 6 (Vorgabe E, tief/hoch)
Saite 2
Saite 3
Saite 4
Saite 5 CH4 LED
Über die LEDs MOD, DLY und REV wird dargestellt, wie nah die gespielte Note der
Referenzstimmung kommt.
MOD LED rot
DLY LED grün
REV LED rot
Note (Stimmung) ist zu hoch
Note ist korrekt gestimmt
Note (Stimmung) ist zu tief
Alle anderen LEDs auf der Vorderseite sind im Tuner-Modus inaktiv.
Durch Drücken eines Tasters auf der Front oder eines angeschlossenen Fußschalters beenden Sie den Tuner-Modus.
20. Bank
Drücken Sie diesen Taster, um durch die ersten drei Patch-Bänke zu blättern.
Bank 1 2
Bank 2 3
Bank 3 1
Die grüne LED zeigt, dass Sie sich in Bank 1 befinden, die orange LED steht für
Bank 2 und die rote schließlich für Bank 3.
ANMERKUNG: Über die Frontseite können Sie nur auf die ersten drei Bänke zugreifen. Wenn Sie Bank 4 oder höher über einen externen Controller (z.B. Software oder Fuß-Controller) aktivieren, leuchten anstelle der Bank-LEDs nun die Channel-
LEDs und zeigen den Patch-Speicherplatz an.
Ein Beispiel:
Patch 11 – Bank-LED rot, LED in Channel 3 leuchtet.
Wenn Sie Bank Up mit einem externen Schalter auswählen, wird Patch 15 aktiviert
- Bank LED aus, Channel 3 an.
Wenn der Verstärker im Manual-Modus arbeitet, leuchtet die Bank-LED nicht.
Der Channel wird zwischengespeichert, während das entsprechende Patch innerhalb der aktuellen Bank geladen wird, während Sie durch die Bänke blättern.
31
32
21 – 24. Channel 1-4
Channel 1 aktiviert das erste Patch in der aktuellen Bank.
Channel 2 aktiviert das zweite Patch in der aktuellen Bank.
Channel 3 aktiviert das dritte Patch in der aktuellen Bank.
Channel 4 aktiviert das vierte Patch in der aktuellen Bank.
25. Footswitch
Hier schließen Sie einen der unterstützten Fußschalter an.
Fußschalter mit 1 Taster
Mit einem Fußumschalter (z.B. Blackstar FS-4) schalten Sie zwischen Channel 1 und
2 der aktuellen Bank um.
Fußschalter aktiviert in der Stellung OFF (Beispiel FS-4: LED leuchtet nicht) Channel 1
Fußschalter aktiviert in der Stellung ON (Beispiel FS-4: LED leuchtet) Channel 2
Blackstar FS-10 Fußleiste
Mit diesem multifunktionalen Fußschalter können Sie auf alle Patches zugreifen und die Effekte sowie Programm-Patches umschalten.
MIDI-Fußleisten
Die Funktionalität hängt vom jeweiligen Controller ab.
26. MP3/Line In
An dieser Buchse schließen Sie den Ausgang Ihres MP3- oder CD-Spielers an. Zum
Üben passen Sie die Lautstärke der externen Quelle an den Pegel Ihrer Gitarre an.
ANMERKUNG: Der Anschluss ist mono ausgelegt.
27. Emulated Output
Dieser Ausgang emuliert den Klangcharakter einer Gitarren-Lautsprecherbox und sorgt in Kombination mit einem Aufnahmegerät oder Mischpult für einen natürlichen
Klang.
Um die Stereo-Effekte nutzen zu können, verwenden Sie ein Y-Kabel, das einen
Stereoklinkenstecker auf zwei Monoklinkenstecker splittet: So können Sie zwei
Kanäle des Aufnahmegeräts oder Mixers ansteuern. Der Ausgang kann aber auch mit einem Mono-Gitarrenkabel belegt werden. Verwenden Sie in jedem Fall hochwertige geschirmte Kabel.
Mit dem Volume-Regler (4) steuern Sie den Pegel des Emulated Outputs. Das
Master Volume steuert nur den (die) angeschlossenen Lautsprecher/Box(en) aus.
ANMERKUNG: Für Aufnahmen ‚ohne Ton’ drehen Sie das Master Volume auf null. Sie können diesen Ausgang auch dann zur Aufnahme verwenden, wenn kein Lautsprecher angeschlossen ist. Stellen Sie jedoch sicher, dass in diesem Fall auch keine Lautsprecherkabel an einem der Lautsprecherausgänge am Verstärker angeschlossen ist, da in diesem Fall die Last-Schutzschaltung umgangen wird und ernsthafte Schäden am Verstärker auftreten können.
28. Recall-Anzeige
Die Recall-Anzeige zeigt, ob der aktuelle Parameterwert im Verstärker mit der physikalischen Position des zugehörigen Reglers auf der Vorderseite übereinstimmt oder nicht. Wenn Sie z. B. zu einem anderen Patch wechseln, entsprechen die
Regler-Einstellungen auf der Frontseite mit Sicherheit nicht den Einstellungen, die
Sie hören.
Um unerwünschte Pegelsprünge beim Einstellen der Parameter zu verhindern, haben die Regler auf der Front keine Funktion, bis die physikalische Position den aktuellen Parameterwert erreicht hat. In diesem Moment blinkt die Recall-Anzeige zweimal und der Regler ‚übernimmt’ die Parametersteuerung, so dass Sie den Wert anheben oder absenken können.
Die Recall-Anzeige blinkt jeweils zweimal, wenn der physikalische Regler den im Patch gespeicherten Wert erreicht bzw. überstreicht: So können Sie den programmierten Wert zu jeder Zeit direkt ablesen.
Recall erfasst nur die Parameter Gain, Volume, Bass, Middle, Treble und ISF.
Wenn der Tuner aktiv ist, blinkt die Recall-Anzeige dauerhaft.
33
34
Rückseite
1. Netzanschluss
Hier wird das mitgelieferte Kaltgerätenetzkabel angeschlossen. Das Kabel muss an einer Netzsteckdose angeschlossen werden, die in puncto Spannung, Leistung und Netzfrequenz den auf der Rückseite vermerkten Spezifikationen entspricht. Im
Zweifelsfall wenden Sie sich an einen qualifizierten Techniker/Elektriker.
Programmierung
Speichern von Patches
So speichern Sie den aktuellen Sound als Patch
1. Drücken und halten Sie einen der vier Channel-Taster für eine Sekunde.
Alle vier Channel-LEDs blinken daraufhin.
2. Drücken Sie den Bank-Taster, um zwischen den drei Bänken (grün, orange, rot) umzuschalten und den Speicherplatz auszuwählen.
3. Drücken Sie einen der vier Channel-Taster einmal, um das Patch auf dem gewählten Speicherplatz abzuspeichern.
Die LED für den gewählten Speicherplatz leuchtet und das neue Patch ist aktiv.
Grüne Bank = Patches 1-4
Orange Bank = Patches 5-8
Rote Bank = Patches 9-12
Mit Hilfe der Regler am Verstärker können Sie das Patch nun zu jedem Zeitpunkt während dem Speichervorgang editieren.
Drücken Sie den Manual-Taster bei Bedarf, um den Speichervorgang abzubrechen:
Der Verstärker wird in den vorherigen Zustand zurückversetzt.
Das Speichern eines Patches überschreibt ein auf dem Speicherplatz eventuell vorhandenes Patch.
Patches können auch über die Blackstar INSIDER Software oder mit Hilfe eines angeschlossenen Blackstar FS-10 Fuß-Controllers gespeichert werden.
Laden von Patches
Drücken Sie einen Channel-Taster, um das zugehörige Patch zu laden.
Durch Drücken des Bank-Tasters blättern Sie durch die drei Bänke – grüne-orangerot. Der Channel bleibt erhalten, während das entsprechende Patch innerhalb der aktuellen Bank geladen wird, während Sie durch die Bänke blättern.
Alternativ können Sie Patches über die Blackstar INSIDER Software oder einen angeschlossenen Fußschalter laden.
USB Audio
Die Kommunikation des Verstärkers mit einem PC oder Mac erfolgt über Standard-
Audio-Treiber, spezifische Treiber werden nicht benötigt.
Der Verstärker erscheint innerhalb der Aufnahme-Software auf dem Computer als
Audio-Interface.
Folgende Audioformate für die USB-Ausgabe können über die Blackstar INSIDER
Software eingestellt werden:
Stereo-Audiokanäle mit Speaker-Emulation und Effekten
2 x Mono-Audiokanäle
- Links – Verstärkersignal mit Effekten
- Rechts – unbearbeitetes Gitarrensignal
Re-Amping-Modus
Re-amping
Über die Blackstar INSIDER Software kann der Verstärker in den Re-Amping-
Modus geschaltet werden. Hierbei handelt es sich um eine nicht-programmierbare
Einstellung, die deaktiviert wird, wenn wahlweise das USB-Kabel entfernt oder der
Verstärker ausgeschaltet wird.
Wenn der Re-Amping-Modus aktiv ist, kann ein bereits aufgenommenes, unbearbeitetes Gitarrensignal über USB in den Verstärker gespeist und ein bearbeitetes Audiosignal wieder ausgegeben werden. Das Return-Signal kann dann
über die Recording-Software im angeschlossenen PC oder Mac aufgenommen werden.
Firmware Update
Firmware-Aktualisierungen werden über die Blackstar INSIDER Software ausgeführt.
Eine neue Version der Blackstar INSIDER Software wird zu jedem Update veröffentlicht. Jedes Update dauert ungefähr 60 - 120 Sekunden.
Wenn der Verstärker über USB mit der INSIDER Software verbunden ist und diese eine neuere Version der Firmware erkennt, wird eine Meldung eingeblendet, die eine
Installation dieser aktuellen Daten vorschlägt. Während der Aktualisierung können die Regler am Verstärker nicht bedient werden. Die Tap-LED blinkt und weist so auf die Datenübermittlung während des Update-Vorgangs hin.
Der Verstärker darf während der Firmware-Aktualisierung nicht ausgeschaltet werden. Wenn der Amp während der Aktualisierung ausgeschaltet wird, können die Regler am Verstärker auch nach dem Einschalten nicht bedient werden und der Verstärker gibt keinen Sound aus. Die Tap-LED blinkt und zeigt so, dass im
Verstärker keine gültige Firmware installiert ist.
Der Verstärker muss an die Blackstar INSIDER Software angeschlossen werden, um eine gültige Firmware zu installieren. Die Aktualisierung wird automatisch ausgeführt, wenn die Blackstar INSIDER Software erkennt, dass sich der Verstärker in diesem
Status befindet.
35
36
Technical Specification
ID:15TVP
Leistung: 15 Watts
Gewicht (kg): 11
Abmessungen (mm): 450(B) x 417(H) x 220(T)
Fußschalter (nicht im Lieferumfang enthalten): FS-4-Fußschalter, FS-10-
Fußleiste
ID:30TVP
Leistung: 30 Watts
Gewicht (kg): 13
Abmessungen (mm): 500(B) x 460(H) x 250(T)
Fußschalter (nicht im Lieferumfang enthalten): FS-4-Fußschalter, FS-10-
Fußleiste
37
38
Cet appareil doit être utilisé dans un environnement bien ventilé et ne doit jamais être mis sous tension si l'endroit est confiné.
All electrical and electronic products should be disposed of separately from the municipal waste stream via designated collection facilities appointed by the government or the local authorities.
39
40
Introduction
Merci d’avoir acheté cet amplificateur Blackstar ID:Series. Comme tous nos produits, cet amplificateur est le résultat d’innombrables heures de recherche et développement minutieux par notre équipe de conception de classe mondiale.
Basée à Northampton (Royaume-Uni), l’équipe Blackstar est composée de musiciens chevronnés et l’unique objectif du processus de développement est de fournir aux guitaristes les outils ultimes pour s’exprimer.
Tous les produits Blackstar sont soumis à des tests intensifs en laboratoire et en conditions réelles pour s’affranchir véritablement de tout compromis en termes de fiabilité, de qualité et avant tout de SON.
L’ID:Series est véritablement révolutionnaire, combinant des innovations uniques, un jeu de commandes intuitives et traditionnelles, et la souplesse de programmation.
Veuillez lire attentivement la totalité de ce mode d’emploi pour tirer le bénéfice maximal de votre nouveau produit Blackstar.
Si vous aimez ce que vous entendez et voulez en découvrir plus sur la gamme de produits Blackstar, veuillez visiter notre site web à l’adresse www.blackstaramps.
com.
Merci !
L’équipe Blackstar
Caractéristiques
Dans les cinq ans qui ont suivi son lancement, Blackstar a montré la voie de l’innovation dans l’amplification de guitare. L’ID Series représente le point culminant de plus sept ans de recherche et développement techniques. Ces amplis ont le jeu de commandes intuitif d’un ampli traditionnel, mais offrent une grande souplesse de programmation. Les commandes uniques vous permettent à vous, le guitariste, de concevoir votre propre son, de le mémoriser et d’être sûr de la façon dont l’ampli se comportera en live.
La technologie True Valve Power , en instance de brevet, offre six réponses de lampes de puissance distinctement différentes – EL84, 6V6, EL34, KT66, 6L6,
KT88. Quand on l’active, elle fournit la réponse, la dynamique, la compression de la redresseuse (« sag ») et la rupture caractéristiques d’un ampli à lampes, et de façon unique elle donne la même puissance de sortie acoustique que son équivalent à lampes. Cela signifie que ces amplis assurent sans compromis en live – True Valve
Power signifie « LOUD as valve™ » (aussi fort que les lampes).
La commande Voice a six réglages différents – Clean Warm, Clean Bright, Crunch,
Super Crunch, OD 1, OD 2. Quand on les utilise avec la commande ISF brevetée de
Blackstar, vous pouvez obtenir exactement le son auquel vous pensiez.
La section d’effets offre simultanément des effets de qualité studio pour la modulation, le delay et la reverb, que vous pouvez mémoriser avec votre son.
L’édition en profondeur et la mémorisation des patches est simple grâce au logiciel
INSIDER par Blackstar. Les patches peuvent être partagés, mis à disposition et téléchargés via la communauté en ligne. Le connecteur USB vous permet aussi d’enregistrer directement votre ampli dans votre ordinateur.
Une sortie à émulation de baffle, une entrée MP3/ligne et une commutation MIDI au pied complètent l’ensemble.
Avec l'exceptionnelle commande Voice, l’ISF brevetée et la True Valve Power en instance de brevet, les amplificateurs ID offrent une flexibilité et une simplicité sans
égales, vous permettant de concevoir véritablement le son que vous avez en tête et de le fournir live « LOUD as valve™ ». Individuality is power!
41
42
Mode Démo
Quand l’amplificateur est allumé pour la première fois après l’achat, ou après une réinitialisation d’usine, il est en « mode Démo ». Le son que vous entendez reflétera la position physique des boutons de la face avant comme ce serait le cas en mode manuel. Tous les effets plus la TVP seront coupés.
Toutes les mémoires de patch de l’amplificateur contiennent par défaut des réglages d’origine Blackstar. Des patches peuvent être créés et mémorisés en mode Démo mais les patches et réglages d’origine par défaut seront restaurés chaque fois que l’amplificateur sera éteint et rallumé.
Pour quitter le mode Démo, maintenez le bouton Manual (19) pendant que vous allumez l’amplificateur. Le voyant à LED Bank (20) passe du rouge au orange puis au vert et enfin s’éteint pour indiquer que le mode Démo a été désactivé. Si le bouton
Manual est relâché avant que la LED Bank ait passé en revue toutes les couleurs et se soit éteinte, alors l’opération est annulée et l’amplificateur reste en mode Démo.
Le logiciel INSIDER de Blackstar peut également être utilisé pour sortir du mode
Démo. Depuis ce programme, faites un clic droit sur l’intitulé Demo Mode et sélectionnez « Disable » (désactiver).
Réinitialisation d’usine
Les patches et réglages d’origine par défaut peuvent être à tout moment restaurés dans votre amplificateur. Maintenez simplement pressés simultanément les boutons MOD, DLY et REV, pendant que vous allumez l’amplificateur. La LED Bank s’allumera et passera du vert au orange au rouge pour indiquer l’imminence de la réinitialisation d’usine. Ce processus prend un total de 2 secondes. Si n’importe lequel des boutons MOD, DLY ou REV est relâché avant que la LED Bank n’ait passé en revue toutes ces couleurs, alors l’opération est annulée et l’amplificateur ne subit aucune modification.
Une fois cela terminé, l’amplificateur retrouve le mode Démo.
NOTE IMPORTANTE: ce processus écrasera tout contenu créé par l’utilisateur.
43
44
Face avant
1. Input
Branchez ici votre guitare. Utilisez toujours un cordon blindé de bonne qualité pour guitare.
2. Voice
La commande Voice change l’harmonisation du préampli, en allant du son ultra-clair
à la saturation extrême.
Clean Warm – Très propre, dynamique
Clean Bright – « Boutique », en rupture si on le pousse à fond
Crunch – Saturation classique à gain moyen
Super Crunch – Plus de gain et de punch que Crunch
OD 1 – Saturation gonflée par volume Master avec amortissement moyen de
l’ampli de puissance
OD 2 – Saturation gonflée renforcée dans les médiums
Ce réglage est sauvegardé quand vous mémorisez un patch.
3. Gain
La commande Gain règle l’ampleur de la saturation ou de la distorsion. Des réglages bas, dans le sens anti-horaire, donneront un son clair, à la limite de la saturation.
Quand on tourne la commande Gain dans le sens horaire, le son devient plus saturé, allant vers de superbes sons Crunch jusqu’à sa position maximale, pour laquelle on obtient un son à pleine distorsion. Ce réglage est sauvegardé quand vous mémorisez un patch.
4. Volume
Contrôle le volume du préampli. Le tourner dans le sens horaire augmente le volume.
Des hauts niveaux de volume introduiront l’effet de distorsion et de compression d’un ampli de puissance à lampes, selon le réglage TVP (8) que vous avez sélectionné.
Ce réglage est sauvegardé quand vous mémorisez un patch.
5. Bass
La commande Bass règle la quantité de basses fréquences dans votre son. Cet ampli a un circuit de façonnage sonore sophistiqué qui permet de passer d’un son nerveux et tranchant (dans le sens anti-horaire) à un son chaud et lourd (sens horaire). Ce réglage est sauvegardé quand vous mémorisez un patch.
6. Treble
La commande Treble permet le réglage exact des aigus (hautes fréquences) dans le son. Avec des réglages bas (dans le sens anti-horaire), le son aura un caractère chaud et feutré. Quand on monte la commande Treble (sens horaire), le son devient plus brillant. Au réglage maximal, le son sera agressif et tranchant. Ce réglage est sauvegardé quand vous mémorisez un patch.
7. ISF
La commande ISF brevetée fonctionne en conjonction avec les commandes Bass, Middle et Treble. Elle vous permet de choisir la signature tonale exacte que vous préférez. À fond dans le sens anti-horaire, elle donne un caractère plus américain avec des graves nerveux et des médiums plus agressifs, et à fond dans le sens horaire, un caractère britannique plus « woody » et moins agressif.
USA UK
Contrairement aux commandes « contour » conventionnelles et aux systèmes
égaliseurs paramétriques, les commandes Bass, Middle et Treble restent interactives comme dans un réseau de correction traditionnel d’amplificateur de guitare. Cela donne une réponse musicale, très familière. Ce réglage est sauvegardé quand vous mémorisez un patch.
8. Sélecteur TVP (True Valve Power)
La True Valve Power de Blackstar, en instance de brevet, offre 6 réponses de lampes de puissance distinctement différentes – EL84, 6V6, EL34, KT66, 6L6 et
KT88. Quand on l’active, elle fournit la réponse, la dynamique, la compression de la redresseuse (« sag ») et la saturation caractéristiques d’un ampli à lampes, et de façon unique elle donne la même puissance de sortie acoustique que son équivalent
à lampes. Cela signifie que ces amplis assurent sans compromis en live – True Valve
Power signifie « LOUD as valve™ » (aussi fort que les lampes).
La TVP change les caractéristiques du son en le faisant passer d’un son compressé et souple à un son dynamique et nerveux.
EL84
6V6
EL34
KT66
6L6
KT88
Son classe A riche et carillonnant avec beaucoup de compression
Son classe A net et précis avec forte compression et médiums nerveux
Son crunch britannique classique de classe A/B avec rupture riche et douce
Son classe A/B britannique vintage à haute polarisation, riche et chaud
Son classe A/B dynamique et nerveux avec aigus et graves étendus
Son classe A/B dynamique, audacieux et nerveux avec de solides graves
Quand vous passez d’EL84 à KT88, la quantité de compression et de saturation pouvant être obtenue par chaque réponse de lampes se réduit. De plus, quand un des deux sons clairs est sélectionné, la compression de sortie et la saturation sont affectées par la commande Gain.
Ce réglage est sauvegardé quand vous mémorisez un patch.
9. Commutateur TVP (True Valve Power)
Presser ce commutateur met la TVP en/hors service. La LED intégrée au commutateur s’allume pour signaler que la TVP est en service. Quand la LED est
éteinte, la TVP n’est pas active et le sélecteur TVP est désactivé. Ce réglage est sauvegardé quand vous mémorisez un patch.
NOTE: avec la TVP désactivée, l’amplificateur de puissance a une réponse linéaire et vous ne pourrez pas obtenir le « sag », la compression et la puissance typiques des lampes qu’offre la TVP.
45
46
Effets
Trois effets de qualité studio peuvent être mis en service à tout moment.
10. MOD (Modulation)
Pressez ce commutateur afin de mettre l’effet de modulation en/hors service ou de le choisir pour l'éditer. Ce réglage est sauvegardé quand vous mémorisez un patch.
11. DLY (Delay)
Pressez ce commutateur afin de mettre l’effet delay (retard) en/hors service ou de le choisir pour l'éditer. Ce réglage est sauvegardé quand vous mémorisez un patch.
12. REV (Reverb)
Pressez ce commutateur afin de mettre l’effet reverb en/hors service ou de le choisir pour l'éditer. Ce réglage est sauvegardé quand vous mémorisez un patch.
Pour les trois commutateurs d’effet, la LED indique leur statut :
LED
LED éteinte
LED rouge
LED verte
Statut de l’effet
Effet désactivé
Description
L’effet n’est pas en service
Effet activé mais pas choisi pour l’édition L’effet est en service mais il n’est pas affecté par les commandes d’effet de la face avant
Effet activé et choisi pour l’édition L’effet est en service et est affecté par les commandes d’effet de la face avant
Presser répétitivement chaque commutateur d’effet de la face avant donne le résultat suivant :
Effet désactivé Active l’effet et le choisit pour l’édition. Tout effet préalablement choisi pour l’édition retrouve son simple statut activé
Effet activé mais pas choisi pour l’édition
Choisit l’effet pour l’édition. Tout effet préalablement choisi pour l’édition retrouve son simple statut activé
Effet activé et choisi pour l’édition
Désactive l’effet. Si un ou d’autres effets sont activés, l’effet préalablement choisi pour l’édition le redevient
NOTE: un seul effet peut être choisi à la fois pour l’édition.
13. Type d’effet
Change le type d’effet et modifie un paramètre de l’effet actuellement choisi pour l’édition (modulation, delay ou reverb).
Chaque segment représente un effet différent (quatre pour chaque type d’effet).
Une LED indique le type d’effet actuellement activé. La distance parcourue dans le
« segment » modifie un paramètre de l’effet. Le effet tableau ci-dessous montre les paramètres modifiables.
Ce réglage est sauvegardé quand vous mémorisez un patch.
14. Niveau d’effet (Level)
Modifie un paramètre d’effet. Pour les effets de modulation et de retard (delay), tourner la commande Level en maintenant enfoncé le commutateur Tap (15) modifie la cadence/ durée de l’effet.
Le effet tableau ci-dessous montre les paramètres modifiables.
Ce réglage est sauvegardé quand vous mémorisez un patch.
15. Tap
Le commutateur Tap sert à régler la cadence/durée de l’effet actuellement choisi pour l’édition. L’intervalle de temps séparant deux pressions du bouton Tap définit la cadence.
Une fois cela réglé, la LED Tap clignote au rythme ainsi fixé dans l’effet actuellement choisi pour l’édition.
Le effet tableau ci-dessous montre les paramètres modifiables :
Effet Paramètre du segment Paramètre réglé par
Level
Paramètre réglé par Tap
MODULATION
Phaser
Flanger
Chorus
Tremolo
Mixage
Réinjection
Mixage
Ampleur de modulation de fréquence
DELAY
Linear
Analogue
Tape
Multi
REVERB
Room
Hall
Spring
Plate
Réinjection
Réinjection
Réinjection
Réinjection
Taille
Taille
Taille
Taille
Profondeur
Profondeur
Profondeur
Ampleur de modulation d’amplitude
Niveau de retard
Niveau de retard
Niveau de retard
Niveau de retard
Niveau de reverb
Niveau de reverb
Niveau de reverb
Niveau de reverb
-
-
-
-
Vitesse
Vitesse
Vitesse
Vitesse
Temps
Temps
Temps
Temps
Ce réglage est sauvegardé quand vous mémorisez un patch.
16. Volume Master
Commande le volume général de votre amplificateur. Tourner cette commande dans le sens horaire augmente le volume. C’est un réglage global qui n’est pas sauvegardé quand vous mémorisez un patch.
Si le volume Master est à zéro, cela permet d’enregistrer en silence via la sortie avec
émulation de baffle ou l’USB. Le niveau émulé est contrôlé au moyen du volume du préampli.
47
48
17. Interrupteur d’alimentation Power
Cet interrupteur sert à mettre l’amplificateur sous et hors tension. Le point blanc signifie que l'amplificateur est sur.
NOTE : en mode Démo, éteindre l’amplificateur et le rallumer restaure les réglages d’usine par défaut. En dehors du mode Démo, l’amplificateur retrouve les réglages qu’il avait à l’extinction. .
18. USB
Branchez ici un câble USB pour relier l’amplificateur à un PC sous Windows ou à un
Mac. Le logiciel INSIDER de Blackstar peut être téléchargé depuis notre site web et offre une foule de fonctions.
Voir la section Audio USB en page 69 pour plus d’informations.
NOTE : l’amplificateur apparaîtra dans le logiciel d’enregistrement d’un ordinateur personnel comme un périphérique de capture audio.
19. Manual
Pressez ce commutateur pour alterner entre le mode manuel et le patch actuel.
Quand l’amplificateur est en mode manuel, le son reflète la position physique actuelle des commandes. Cela s’applique aux commandes Voice, Gain, Volume,
Bass, Middle, Treble, ISF et TVP. Le statut On/Off de TVP sera toujours celui du dernier patch activé. Tous les effets qui étaient actifs lors du passage en mode manuel sont désactivés.
En mode manuel, toutes les commandes peuvent toujours être modifiées par une source externe (logiciel INSIDER de Blackstar, pédalier, contrôleur MIDI), mais cela signifie alors que le son ne correspondra plus aux positions des commandes de la face avant.
Mode accordeur
Maintenir le commutateur Manual (19) durant trois secondes active l’accordeur. La
LED témoin Recall (28) clignotera continuellement pour signaler que l’amplificateur est en mode accordeur. Par défaut, la sortie de l’amplificateur sera coupée en mode accordeur.
Les LED Manual, Bank et CH (canal) indiqueront la note la plus proche de celle jouée.
LED Bank
LED CH1
LED CH2
LED CH3
LED CH4
Cordes 1 et 6 (mi par défaut, grave/aigu)
Corde 2
Corde 3
Corde 4
Corde 5
Les LED MOD, DLY et REV servent d’indication de justesse de la note jouée par rapport à la note accordée.
LED MOD rouge
LED DLY verte
LED REV rouge
La note est trop aiguë (au-dessus de la hauteur juste)
La note est accordée
La note est trop basse (au-dessous de la hauteur juste)
Les autres LED de la face avant seront éteintes en mode accordeur.
Presser n’importe quel commutateur de la face avant ou du pédalier vous fera quitter le mode accordeur.
20. Bank
Pressez ce commutateur pour passer en revue les trois premières banques de patches.
Banque 1 Banque 2
Banque 2 Banque 3
Banque 3 Banque 1
La LED verte indique que vous êtes en banque 1, la LED orange que vous êtes en banque 2 et la LED rouge que vous êtes en banque 3.
NOTE : seules les trois premières banques peuvent être sélectionnées depuis la façade. Quand vous activez la banque 4 ou plus depuis un contrôleur externe (par exemple le logiciel, le pédalier), la LED Bank ne s’allume pas mais les LED de canaux
(CH) continuent de vous indiquer l’emplacement du patch.
Par exemple :
Patch 11 – LED Bank rouge, LED CH3 allumée.
La sélection de la banque up avec un contrôleur externe vous commutera sur le patch 15 - LED de Banques off, Canal 3 allumé
Quand l’amplificateur est en mode manuel, la LED Bank n’est pas allumée.
Le canal sera mémorisé, par conséquent le patch correspondant dans la banque actuelle sera chargé lorsque vous ferez défiler les banques.
21 – 24. Canaux (CH) 1-4
Le canal 1 active le premier patch de la banque actuellement active.
Le canal 2 active le deuxième patch de la banque actuellement active.
Le canal 3 active le troisième patch de la banque actuellement active.
Le canal 4 active le quatrième patch de la banque actuellement active.
25. Pédalier
Branchez ici un des pédaliers pris en charge.
Pédale commutateur (1 bouton)
Utilisez n’importe quelle pédale à commutateur verrouillable (par exemple une FS-4
Blackstar) pour alterner entre les canaux 1 et 2 de la banque actuellement sélectionnée.
Le verrouillage sur OFF de la pédale (c’est-à-dire que la LED est éteinte sur la FS-4) active le canal 1
49
50
Le verrouillage sur ON de la pédale (c’est-à-dire que la LED est allumée sur la FS-4) active le canal2
Pédalier FS-10 Blackstar
Ce pédalier multifonction vous donne accès à tous les patches, à la commutation des effets et à la programmation des patches.
Pédaliers MIDI
Les fonctionnalités dépendent de votre pédalier.
26. Entrée MP3/ligne
Branchez ici la sortie de votre lecteur de MP3 ou de CD. Réglez le volume du lecteur en fonction de celui de votre guitare pour jouer avec.
NOTE: la connexion est mono.
27. Sortie émulée
Cette sortie émule les caractéristiques tonales d’un baffle de guitare et fournit un son naturel pour le branchement à un enregistreur ou à une table de mixage.
Pour tirer pleinement parti des effets stéréo, utilisez un câble en Y avec un jack stéréo vers deux jacks mono comme source pour deux canaux de l’enregistreur ou de la table de mixage. La sortie fonctionnera aussi avec un cordon pour guitare de type mono. Utilisez toujours un cordon blindé de bonne qualité.
Tourner la commande Volume (4) contrôlera le niveau de la sortie émulée. Le volume
Master n’affecte que le ou les haut-parleurs/baffles branchés.
NOTE : pour enregistrer « en silence », réglez le volume Master à zéro. Vous pouvez aussi enregistrer par cette sortie sans avoir branché de haut-parleur mais assurezvous qu’aucun cordon de haut-parleur n’est branché à aucune des prises de sortie pour haut-parleur de cet amplificateur, car cela désactiverait le circuit de protection de charge et entraînerait des dommages pour l’amplificateur.
28. Indicateur Recall
L’indicateur Recall signale une disparité entre la valeur actuelle d’un paramètre dans l’amplificateur et la commande physique correspondante en façade. Par exemple, quand vous changez de patch, les commandes de la face avant peuvent ne plus refléter les réglages que vous entendez.
Pour éviter des sauts brutaux de niveau quand vous réglez une commande, les commandes de la face avant n’ont pas d’effet sur le son tant que vous ne leur avez pas fait rejoindre la valeur actuelle du paramètre. Une fois celle-ci atteinte, l’indicateur Recall clignote deux fois et la commande « prend le contrôle » de la valeur, ce qui lui permet de l’augmenter ou de la diminuer.
L’indicateur Recall clignotera deux fois chaque fois que la commande physique
« passera par » la valeur mémorisée dans le patch actuel, pour que vous puissiez facilement voir la valeur programmée.
Recall ne concerne que les commandes Gain, Volume, Bass, Middle, Treble et ISF.
Quand l’accordeur est en service, l’indicateur Recall clignote continuellement.
Face arrière
1. Entrée d’alimentation secteur
Le cordon d’alimentation secteur détachable fourni se branche ici. Le cordon ne doit être branché qu’à une prise secteur compatible avec les besoins électriques de tension, puissance et fréquence indiqués en face arrière. En cas de doute, demandez conseil à un technicien qualifié.
Programmation
Mémorisation des patches
Pour mémoriser le son actuel comme un patch :
1. Pressez et maintenez n’importe lequel des quatre boutons de canal (CH) durant une seconde. Les quatre LED de canal commenceront à clignoter.
2. Pressez le bouton Bank pour alterner entre les trois banques (verte, orange, rouge) en vue de choisir l’emplacement où vous allez mémoriser.
3. Pressez une fois n’importe lequel des quatre boutons de canal (CH) pour mémoriser le patch à l’endroit choisi.
La LED correspondant à l’emplacement de mémorisation choisi s’allumera et le nouveau patch sera activé.
Banque verte = Patches 1-4
Banque orange = Patches 5-8
Banque rouge = Patches 9-12
Les commandes de l’amplificateur peuvent servir à modifier le patch à tout moment du processus de mémorisation.
Pressez à n’importe quel moment le bouton Manual pour annuler le processus de mémorisation et ramener l’amplificateur à ses derniers réglages.
Mémoriser un patch écrasera (remplacera) tout patch déjà mémorisé à cet emplacement.
Les patches peuvent également être mémorisés au moyen du logiciel INSIDER de
Blackstar ou d’un pédalier FS-10 Blackstar connecté.
Rappel des patches
Pressez n’importe quel bouton de canal (CH) pour charger ce patch.
Presser le bouton Bank vous fera parcourir les trois banques – verte, orange, rouge.
Le canal sera conservé, ce qui signifie que le patch correspondant dans la banque actuelle sera chargé lorsque vous passerez en revue les banques.
Sinon, les patches peuvent être rappelés au moyen du logiciel INSIDER de Blackstar ou de tout pédalier connecté.
51
52
Audio USB
Des pilotes audio standard sont utilisés pour connecter l’amplificateur à un PC ou à un Mac, aucun pilote spécifique n’est nécessaire.
L’amplificateur apparaîtra dans le logiciel d’enregistrement comme un périphérique de capture audio.
Le format de l’audio par USB peut être changé via le logiciel, et peut être un des suivants :
Canaux audio avec effets stéréo et émulation de baffle
2 canaux audio mono
- Gauche – signal d’amplificateur traité
- Droite – signal de guitare non traité
Mode de ré-amplification
Ré-amplification
L’amplificateur peut être commuté en mode de ré-amplification via le logiciel. C’est un réglage non programmable qui sera désactivé soit lorsque le câble USB sera retiré soit lorsque l’amplificateur sera éteint.
Quand il est activé, le mode de ré-amplification permet à l’amplificateur d’accepter un signal de guitare sec préenregistré via USB et de renvoyer un signal audio entièrement traité. Ce signal de retour peut alors être capturé par le logiciel d’enregistrement sur le PC ou Mac connecté.
Mise à jour du firmware
Les mises à jour du firmware sont initiées au moyen du logiciel INSIDER de Blackstar.
Une nouvelle version du logiciel INSIDER de Blackstar sortira lorsqu’une mise à jour sera disponible. Chaque mise à jour nécessite environ 60 à 120 secondes.
Quand l’amplificateur est connecté (par USB) à une version contenant un firmware plus récent, un message s’affiche, vous demandant d’installer les derniers fichiers.
Durant la mise à jour, les commandes de l’amplificateur ne sont pas opérationnelles.
La LED Tap clignote pour indiquer l’activité d’échange de données durant le processus de mise à jour.
L’alimentation de l’amplificateur ne doit pas être coupée durant une mise à jour de firmware. Si l’amplificateur est coupé durant une mise à jour, les commandes ne répondront pas lorsqu’il sera rallumé et l’amplificateur ne produira aucun son.
La LED clignotera pour indiquer que l’amplificateur ne contient pas de firmware exploitable.
L’amplificateur doit être connecté au logiciel INSIDER de Blackstar pour réinstaller un firmware valable. Le processus de mise à jour démarrera automatiquement si le logiciel INSIDER de Blackstar détecte que l’amplificateur est dans ces conditions.
Caractéristiques techniques
ID:15TVP
Puissance: 15 Watts
Poids (kg): 11
Dimensions (mm): 450(L) x 417(H) x 220(P)
Pédalier (pas fourni): pédale verrouillable FS-4, pédalier FS-10
ID:30TVP
Puissance: 30 Watts
Poids (kg): 13
Dimensions (mm): 500(L) x 460(H) x 250(P)
Pédalier (pas fourni): pédale verrouillable FS-4, pédalier FS-10
53
54
ESTE EQUIPO SE DEBERá USAR EN UNA ZONA BIEN VENTILADA Y NUNCA
SE DEBERá ENCENDER EN ESPACIOS POCO VENTILADOS, COMO UNA
ESTANTERíA.
All electrical and electronic products should be disposed of separately from the municipal waste stream via designated collection facilities appointed by the government or the local authorities.
55
56
Introducción
Gracias por comprar este amplificador Blackstar ID Series. Como todos nuestros productos, este amplificador es el resultado de incontables horas de meticulosa
Investigación y Desarrollo por parte de nuestro prestigioso equipo de diseño.
Con base en Northampton (Reino Unido), el equipo de Blackstar está formado por músicos experimentados y el único objetivo del proceso de desarrollo es proporcionar a los guitarristas con productos que sean las herramientas de autoexpresión definitivas.
Todos los productos Blackstar son sometidos a intensivas pruebas de laboratorio y de rodaje para asegurar que están fuera de compromiso en términos de fiabilidad, calidad y, sobre todo, TONO.
Los ID Series suponen un verdadero logro. Combinan innovaciones únicas, un set de control tradicional e intuitivo y la versatilidad de un amplificador programable.
Por favor lee este manual detenidamente para asegurarte de que obtienes el máximo rendimiento de tu nuevo producto Blackstar.
Si te gusta lo que oyes y quieres averiguar más acerca de la línea de productos
Blackstar, por favor visita nuestro sitio web en www.blackstaramps.com.
¡Gracias!
El Equipo de Blackstar
Características
En los cinco años transcurridos desde su lanzamiento, Blackstar ha liderado el camino de la innovación en amplificadores de guitarra. Los ID Series representan la culminación de más de siete años de investigación técnica y desarrollo. Estos amplificadores tienen un intuitivo panel de control, pero con la versatilidad que ofrece un amplificador programable. Los controles únicos te permiten a ti, el guitarrista, diseñar tu propio sonido, guardarlo y tener la seguridad de que el amplificador responderá en directo.
El sistema True Valve Power –Verdadera Potencia a válvulas –, pendiente de patente por parte de Blackstar, ofrece seis respuestas distintas de diferentes válvulas de potencia: EL84, 6V6, EL34, KT66, 6L6 y KT88. Cuando se conecta, entrega la respuesta, dinámica, amortiguación y saturación típicos de un amplificador a válvulas y proporciona el mismo nivel de potencia acústica que una etapa de potencia a válvulas equivalente. Esto significa que estos amplificadores se pueden usar en directo sin problemas. True Valve Power significa LOUD as valve TM .
El control Voice tiene seis ajustes diferentes: Clean Warm, Clean Bright, Crunch,
Super Crunch, OD 1 y OD 2.
Cuando se usan junto al control ISF –patentado por Blackstar– puedes obtener exactamente el sonido en el que estás pensando.
La sección Effects proporciona efectos con calidad de estudio para modulación, reverb y delay que puedes almacenar junto con tu sonido.
La edición avanzada de los bancos de sonido, muy sencilla, se realiza usando el software INSIDER de Blackstar. Los bancos se pueden descargar y compartir con la comunidad de usuarios en línea. El conector USB también te permite grabar directamente desde tu amplificador al ordenador.
Una salida emulada, entrada de línea o MP3 y control MIDI completan el equipamiento.
Usando el único control Voice, el patentado ISF y el pendiente de patente True Valve
Power, los amplificadores ID ofrecen una incomparable flexibilidad y facilidad de uso, permitiéndote, en la práctica, diseñar el sonido en tu cabeza y llevarlo al directo con la potencia real de las válvulas - Loud as valve TM
Individuality is power!
57
58
Modo Demo
Al encenderlo por primera vez, o tras restablecer los ajustes de fábrica, el amplificador estará en modo Demostración. El sonido que escuchas reflejará la posición física de los controles del panel frontal. Todos los efectos, además del control TVP, estarán apagados.
Todos los bancos de sonido del amplificador incorporan los preajustes por defecto de Blackstar. Los preajustes se pueden crear y almacenar en modo Demo, pero los ajustes de fábrica se restablecerán cada vez que el amplificador se apague y se vuelva a encender.
Para salir del modo Demostración, mantén pulsado el botón Manual (19) mientras que enciendes el amplificador. El indicador (20) de banco de sonido cambiará de color según la siguiente secuencia: rojo, naranja, verde y finalmente se apagará para indicar que el modo Demostración ha sido desactivado. Si el botón Manual se suelta antes de este ciclo de colores el amplificador volverá al modo Demostración.
El software INSIDER de Blackstar también se puede utilizar para desactivar el modo
Demostración. Desde el programa, haz click con el botón derecho del ratón en la etiqueta “Demo Mode” y selecciona ‘Disable’.
Reestablecer ajustes de fábrica
Los bancos de sonido por defecto se pueden restablecer en cualquier momento.
Simplemente mantén pulsados simultáneamente los botones MOD, DLY y REV, mientras enciendes el amplificador. El indicador de banco de sonidos cambiará de color según la siguiente secuencia: verde, naranja y rojo, para indicar que se van a restablecer los ajustes. Este proceso dura un total de dos segundos. Si alguno de los botones MOD, DLY o REV se suelta antes de que el indicador LED haya finalizado la secuencia de colores hasta finalmente apagarse, la operación será cancelada y el amplificador permanecerá como estaba antes de iniciar el proceso.
Una vez restablecidos los preajustes el amplificador estará en modo Demostración.
NOTA IMPORTANTE: Este proceso eliminará cualquier contenido guardado por el usuario.
59
60
Panel Frontal
1. Input
Conecta tu guitarra aquí. Usa siempre un cable apantallado de calidad.
2. Voice
El control Voice cambia el carácter del previo, desde limpios cristalinos hasta distorsión extrema.
Clean Warm – Sonido muy limpio y dinámico.
Clean Bright – Limpio de ‘Boutique’, romperá cuando se rasguee con fuerza.
Crunch – Distorsión clásica de alta ganancia.
Super Crunch – Versión más distorsionada del canal Crunch
OD 1 – Potente distorsión con volumen master, amortiguación de etapa media.
OD 2 – Potente distorsión con énfasis en frecuencias medias.
Este ajuste se almacenará al guardar un banco de sonido.
3. Gain
El control Gain ajusta la cantidad de overdrive o distorsión. Ajustes bajos (sentido anti-horario) entregarán un sonido limpio a punto de romper. A medida que el control de distorsión se incrementa en sentido horario el sonido se volverá más distorsionado, moviéndose a través de ricos tonos crunch hasta, en su máxima posición, alcanzar un sonido totalmente distorsionado. Este ajuste se almacenará al guardar un banco de sonido.
4. Volume
Este control ajusta el volumen del previo. Girarlo en sentido horario incrementa el volumen. Altos niveles de volumen introducirán el efecto de distorsión y compresión de la etapa de potencia, dependiendo del ajuste del control TVP (8). Este ajuste se almacenará al guardar un banco de sonido.
5. Bass
El control Bass ajusta la cantidad de frecuencias graves en tu sonido. Este amplificador tiene un avanzado circuito de formación de tono que permite que el sonido sea contundente y cortante (sentido anti-horario) o cálido y pesado (sentido horario). Este ajuste se almacenará al guardar un banco de sonido.
6. Treble
El control Treble permite un ajuste exacto de las frecuencias agudas o altas en tu sonido. A niveles bajos (sentido anti-horario) el sonido será oscuro y caliente en carácter. A medida que el control Treble se incrementa en sentido horario el sonido se volverá más brillante. Este ajuste queda almacenado al guardar un banco de sonido.
EL84
6V6
EL34
KT66
6L6
KT88
7. ISF
El control ISF funciona en conjunto con los controles
Bass, Middle y Treble. Te permite elegir la firma tonal exacta que prefieras. Ajustes anti-horarios proporcionan una característica más Americana con bajos apretados y medios agresivos, mientras que los ajustes en sentido horario tienen un tono Británico, que es más denso y menos agresivo.
USA UK
A diferencia de los convencionales controles de cuerpo o ‘contour’ y sistemas de ecualización paramétrica, los controles Bass, Middle y Treble permanecen interactivos los unos con los otros al igual que en un control de tono de guitarra tradicional. Esto conduce a una respuesta muy musical y familiar. Este ajuste queda almacenado al guardar un banco de sonido.
8. Selector TVP (True Valve Power)
El control True Valve Power, pendiente de patente por parte de Blackstar, ofrece seis respuestas de frecuencia diferenciadas de válvulas de potencia – EL84, 6V6,
EL34, KT66, 6L6 y KT88. Cuando se conecta entrega la respuesta, dinámica, amortiguación y saturación típicas de un amplificador a válvulas y, de una forma
única, entrega la misma potencia de salida acústica que en un? amplificador valvular equivalente. Esto significa que estos amplificadores se pueden usar en directo sin problemas. True Valve Power significa LOUD as valve TM .
El control TVP cambia las características de la compresión, dinámica y definición de tu sonido.
Sonido brillante de Clase A muy comprimido.
Sonido crujiente de Clase A con compresión fuerte y medios apretados.
Clásico sonido británico de Clase A/B. Crujiente y lleno de cuerpo.
Sonido Británico vintage, rico y cálido. Clase A/B.
Sonido apretado y dinámico de clase A/B con graves y agudos extendidos.
Apretado, dinámico y redondo sonido de Clase A/B con bajos muy presentes.
A medida que te mueves desde EL84 hasta KT88 se reduce la cantidad de compresión y distorsión disponible para las respuestas de cada válvula.
Adicionalmente, cuando alguno de los sonidos limpios (CLEAN) está seleccionado la compresión y saturación de la etapa se ven afectadas por el control de ganancia.
Este ajuste queda almacenado al guardar un banco de sonido.
9. Interruptor TVP (True Valve Power)
Presionar este interruptor conecta o desconecta el control TVP. El LED interno se encenderá para indicar que el modo TVP está conectado. Cuando el LED está apagado, el modo TVP está inactivo y el selector TVP estará desactivado. Este ajuste queda almacenado al guardar un banco de sonido.
NOTA: Cuando el modo TVP está apagado la etapa de potencia tiene una respuesta lineal y no proporcionará la respuesta, compresión y potencia que entrega el modo
TVP.
61
62
Efectos
Se pueden utilizar hasta tres efectos con calidad de estudio simultáneamente.
10. MOD (Modulación)
Pulsa este interruptor para conectar o desconectar el efecto de modulación, o seleccionar el efecto para su edición. Este ajuste queda almacenado al guardar un banco de sonido.
11. DLY (Delay)
Pulsa este interruptor para conectar o desconectar el efecto de delay (retardo), o seleccionar el efecto para su edición. Este ajuste queda almacenado al guardar un banco de sonido.
12. REV (Reverb)
Pulsa este interruptor para conectar o desconectar el efecto de reverberación, o seleccionar el efecto para su edición. Este ajuste queda almacenado al guardar un banco de sonido.
Para cada uno de los tres efectos el funcionamiento del LED indicador es similar:
LED
LED apagado
LED rojo
Estado de efecto
Apagado
Descripción
El efecto no estará activo
LED verde
Encendido (no permite edición)
Encendido (permite edición)
El efecto estará activo, pero no responde a los controles del panel frontal
El efecto estará activo y responderá a los controles del panel frontal
Al pulsar repetidamente cada uno de los controles de efecto obtendremos la siguiente secuencia:
Efecto apagado Enciende el efecto y lo selecciona para edición. Cualquier efecto previamente seleccionado para edición vuelve a su estado normal.
Efecto encendido pero no seleccionado para edición
Selecciona el efecto para su edición. Cualquier efecto previamente seleccionado para edición vuelve a su estado normal.
Efecto encendido y seleccionado para edición
Apaga el efecto, quedando seleccionado para edición el último efecto seleccionado en caso de que quedase algún efecto encendido.
NOTA: Sólo un efecto puede estar seleccionado para edición cada vez.
13. Effect Type (Tipo de Efecto)
Cambia el tipo de efecto y edita un parámetro del efecto que esté actualmente seleccionado para edición. (Modulación, delay ó reverb).
Cada segmento representa un efecto diferente (hay cuatro para cada tipo de efecto). UN LED muestra el tipo de efecto que se encuentra activo. La distancia recorrida por el segmento modifica un parámetro del efecto. La efectos tabla de abajo muestra los parámetros modificables:
Este ajuste queda almacenado al guardar un banco de sonido.
14. Effect Level (Nivel de Efecto)
Este control modifica un parámetro de efecto. Para los efectos de modulación y delay, girar el control de nivel mientras se presiona el interruptor Tap (15) modifica la frecuencia o el tiempo del efecto.
La effectos tabla de abajo muestra los parámetros modificables:
Este ajuste queda almacenado al guardar un banco de sonido.
15. Tap
El interruptor Tap se usa para ajustar la frecuencia ó tiempo del efecto seleccionado para edición actual. El tiempo entre pulsaciones del interruptor Tap estable la frecuencia del efecto.
Una vez establecido, el LED del interruptor Tap parpadeará indicando la frecuencia del efecto seleccionado.
La efectos tabla de abajo muestra los parámetros modificables:
Efecto Segmento Level Parameter Tap Parameter
MODULATION
Phaser
Flanger
Chorus
Tremolo
Mezcla general
Realimentación
Mezcla general
Profundidad de la modulación de frecuencia
DELAY
Linear
Analógico
Cinta
Multi
REVERB
Room
Hall
Spring
Plate
Realimentación
Realimentación
Realimentación
Realimentación
Tamaño
Tamaño
Tamaño
Tamaño
Profundidad ó ‘Depth’
Profundidad ó ‘Depth’
Profundidad ó ‘Depth’
Profundidad de la modulación de amplitud
Nivel de delay
Nivel de delay
Nivel de delay
Nivel de delay
Nivel de Reverb
Nivel de Reverb
Nivel de Reverb
Nivel de Reverb
Este efecto queda almacenado al guardar un banco de sonido.
Velocidad
Velocidad
Velocidad
Velocidad
Tiempo
Tiempo
Tiempo
Tiempo
Inactivo
Inactivo
Inactivo
Inactivo
16. Master Volume
Controla el volumen general de tu amplificador. Girándolo en sentido horario se incrementa el volumen.
Este es un ajuste global y no queda almacenado al guardar un banco de sonido.
63
64
Si el volumen master está a cero, el amplificador se puede utilizar para grabación silenciosa a través de la salida emulada o el conector USB. El nivel de la salida emulada es controlado mediante el volumen del preamplificador.
17. Power Switch (Interruptor de Encendido)
Este interruptor se utiliza para encender y apagar el amplificador. El punto blanco significa que el amplificador está en.
NOTA: si apagas el amplificador desde el modo Demo se restaurarán los valores por defecto de fábrica. En modo normal el amplificador guardará el estado previo al apagado.
18. USB
Conecta un cable mini USB aquí para enlazar tu amplificador con un sistema
Windows o Mac. El software INSIDER de Blackstar se puede descargar desde nuestro sitio web y ofrece un gran número de posibilidades.
Consulta la sección de Audio USB en la página 79 para más información.
NOTA: El amplificador aparecerá como “Dispositivo de grabación de audio” en la lista de periféricos de tu ordenador.
19. Manual
Pulsa este interruptor para cambiar entre modo manual y el banco de sonido actual.
Cuando el amplificador está en modo manual, el sonido reflejará la posición física de los controles del panel frontal. Esto es aplicable a los controles Voice, Gain, Volume,
Bass, Middle, Treble, ISF y TVP. El estado del control TVP se obtendrá del último banco de sonido guardado. Los efectos que estén activos cuando se cambie al modo manual se desactivarán.
En modo manual cualquiera de los controles se puede modificar mediante una fuente externa (Blackstar INSIDER, Pedal de control, Controladora MIDI…), pero esto significa que el sonido del amplificador no se corresponderá con la posición física de los controles del panel frontal.
Afinador
Al mantener pulsado el interruptor Manual (19) durante tres segundos se activará el afinador. El LED Recall LED (28) parpadeará continuamente para indicar que el amplificador se encuentra en modo Afinador. Por defecto la salida del amplificador se silenciará en este modo.
Los LEDs Manual y bank junto con los LEDs de los distintos canals indicarán la nota más próxima a la nota detectada:
LED de Banco
CH1 LED
CH2 LED
CH3 LED
CH4 LED
Cuerda 1 y 6 (E por defecto, bajo/alto)
Cuerda 2
Cuerda 3
Cuerda 4
Cuerda 5
Los LEDs MOD, DLY y REV te indicarán la desviación en la afinación para cada nota:
LED MOD (rojo)
LED DLY (verde)
LED REV (rojo)
La nota es más alta que el tono a afinar
La nota está afinada
La nota es más baja que el tono a afinar
Todos los otros LEDs se apagarán durante el modo Afinador.
Al pulsar cualquier interruptor del panel frontal el amplificador volverá al modo normal.
20. Bank (Banco)
Pulsa el interruptor Bank para moverte por los tres primeros bancos de sonidos.
Banco 1 Banco 2
Banco 2 Banco 3
Banco 3 Banco 1
El LED verde indica que estás en el banco 1. El LED naranja indica que estás en el banco 2. El LED rojo indica que estás en el banco 3.
NOTA: Sólo los primeros tres bancos se pueden seleccionar desde el panel frontal. Al activar el banco 4 y superiores mediante un controlador externo (Software, Pedalera,
MIDI…), el LED BANK no se encenderá pero los LEDs de los distintos canales te indicarán la ubicación del ajuste.
Por ejemplo:
Preajuste 11 – LED de banco rojo, LED de canal 3 encendido.
Incrementar el banco con una controladora externa cambiará el preajuste a 15 – LED de banco apagado, LED de canal 3 encendido.
Cuando el amplificador se encuentra en modo manual el LED de banco estará apagado.
El canal será recordado por el amplificador, por tanto el correspondiente preajuste del actual banco se cargará al cambiar entre bancos.
21 – 24. Canales 1-4
El canal 1 activa el primer preajuste del banco active actual.
El canal 2 activa el segundo preajuste del banco active actual.
El canal 3 activa el tercer preajuste del banco active actual.
El canal 4 activa el cuarto preajuste del banco active actual.
25. Pedal de control
Conecta uno de los pedales de control soportados aquí.
Pedal de un interruptor
Usa cualquier pedal con interruptor (p.ej. Blackstar FS-4) para cambiar entre los canales 1 y 2 del banco activo.
Con el interruptor abierto (p.ej. LED apagado en el FS-4) el canal 1 estará activo
65
66
Con el interruptor cerrado (p.ej. LED encendido en el FS-4) el canal 2 estará activo
Controlador Blackstar FS-10
Este pedal multifunción te permite el acceso a todos los preajustes, efectos y programas.
Controladora MIDI
La funcionalidad dependerá de cada controladora.
26. MP3/Line In
Conecta la salida de tu MP3 o reproductor de CD aquí. Ajusta el volumen del reproductor para igualar al volumen de tu guitarra de modo que puedas tocar al mismo tiempo.
NOTA: Esta conexión es mono.
27. Salida emulada
Esta salida emula las características tonales de una pantalla de altavoz y proporciona un tono natural para su conexión a un dispositivo de grabación o una mesa de mezclas.
Para hacer un uso completo de los efectos estéreo, usa un cable jack estéreo que tenga dos salidas mono para conectar a un dispositivo de grabación o una mesa de mezclas. La salida también funcionará con un cable mono. Usa siempre un cable apantallado de buena calidad.
Subir el mando de Volumen (4) ajustará el nivel de la Salida Emulada. El volumen
Master sólo afectará a la salida de altavoz.
NOTA: Para una grabación silenciosa, ajusta el volumen Master a cero. También puedes grabar desde esta salida si no hay ningún altavoz conectado, pero asegúrate antes de que no haya ningún cable conectado a ninguna de las salidas de altavoz del panel trasero del amplificador, ya que esto podría dañar el amplificador.
28. Indicador Recall
El indicadir Recall muestra si hay alguna discrepancia entre el valor actual del parámetro del amplificador y la posición de los controles del panel frontal. Por ejemplo, cuando cambias de preajuste los controles no siempre reflejarán el sonido que escuches.
Para prevenir cambios de nivel inesperados en el control que estás ajustando, los los controles del panel frontal no tendrán ningún efecto en el sonido hasta que el mando alcance el valor del parámetro actual. Una vez alcanzado, el indicador Recall parpadeará dos veces y el mando tomará el control del parámetro, que se podrá aumentar o disminuir.
El indicador Recall parpadeará dos veces cada vez que el mando físico pasa por el valor almacenado en el preajuste actual. De este modo podrás ver fácilmente el valor almacenado.
El indicador Recall solo se activa con los controles Gain, Volume, Bass, Middle, Treble e ISF.
Cuando el afinador está active el indicador Recall parpaderá continuadamente.
Panel Trasero
1. Entrada de corriente
Conecta aquí el cable de corriente incluido. Este cable sólo se debe conectar a una toma de corriente compatible con el voltaje, potencia y frecuencia requeridos en el panel trasero. En caso de duda pregunta a un técnico cualificado.
Programabilidad
Guardar Preajustes
Para guardar el sonido actual como un preajuste:
1. Pulsa y mantén cualquiera de los cuatro interruptores de canal. Los cuatro LEDs de canal parpadearán.
2. Pulsa el interruptor Bank para cambiar entre los tres bancos diferentes (verde, naranja, rojo).
3. Pulsa cualquiera de los cuatro interruptores de canal una sola vez para guardar el preajuste en la ubicación elegida.
El correspondiente LED se iluminará y el nuevo preajuste estará activo.
Banco Verde = Preajustes 1-4
Banco Naranja = Preajustes 5-8
Banco Rojo = Preajustes 9-12
Los controles del amplificador se pueden usar para editar un preajuste en cualquier momento del proceso.
Pulsa el interruptor Manual en cualquier momento para cancelar el proceso y volver al estado anterior del amplificador.
Guardar un preajuste borrará cualquier contenido que hubiese previamente en la memoria seleccionada.
Los preajustes también se pueden editar a través del software INSIDER de Blackstar o una pedalera FS-10.
Recuperando Preajustes
Pulsa cualquier interruptor de canal para cargar un preajuste.
Pulsar el interruptor Bank cambiará los distintos bancos. El canal se mantendrá, de modo que el correspondiente preajuste del banco actual se cargará cuando te muevas entre bancos
Alternativamente, los preajustes se pueden cargar mediante el software INSIDER de
Blackstar o un controlador externo.
67
68
Audio USB
Se pueden utilizar controladores de audio estándar para conectar el amplificador a un PC ó Mac. No se requieren controladores específicos.
El amplificador aparecerá como dispositivo de grabación de audio en nuestro panel de control.
El formato de audio USB se puede cambiar a través del software INSIDER de
Blackstar, y se puede ajustar a uno de los siguientes:
Salida emulada de altavoz con efectos estéreo
Modo Re-Amping
- Canal Izquierdo – salida de guitarra sin procesar
- Canal Derecho – salida de guitarra con efectos
Modo Re-Amping
El amplificador se puede configurar en modo ‘Re-Amping’ a través del software
INSIDER. Este es un ajuste no programable y se desactivará al desconectar el cable
USB o al apagar el amplificador.
Activar el modo ‘Re-Amping’ permite al amplificador procesar una señal de guitarra pregrabada a través de USB y devolver una señal totalmente procesada. Esta señal se puede capturar usando un software de grabación en el PC o Mac que estemos utilizando.
Actualización de Firmware
Las actualizaciones de Software se realizan mediante el software INSIDER de
Blackstar. Se lanzará una nueva versión del software INSIDER de Blackstar siempre que una actualización esté disponible. Cada actualización llevará aproximadamente
60-120 segundos.
Cuando el amplificador se conecta vía USB a una versión del software INSIDER de
Blackstar conteniendo un nuevo firmware, se mostrará un mensaje preguntando por la instalación de los últimos ficheros. Mientras se actualiza, los controles del amplificador no responderán. El LED ‘Tap’ parpadeará para indicar que hay actividad de datos durante el proceso de actualización.
El amplificador no se debe apagar durante una actualización de firmware. Si el amplificador se apaga durante una actualización, los controles no responderán tras volver a encenderlo y el amplificador no producirá ningún sonido. El LED ‘Tap’ parpadeará para indicar que el amplificador no contiene ningún firmware válido.
El amplificador se debe conectar al software INSIDER de Blackstar para reinstalar un firmware válido. El proceso de actualización comenzará automáticamente si el software INSIDER de Blackstar detecta que el amplificador no contiene un firmware válido.
Especificaciones técnicas
ID:15TVP
Potencia 15 Watios
Peso (kg): 11
Dimensiones (mm): 450(W) x 417(H) x 220(D)
Pedal (no incluido): FS-4 no momentáneo, controladora FS-10
ID:30TVP
Potencia 30 Watios
Peso (kg): 13
Dimensiones (mm): 500(W) x 460(H) x 250(D)
Pedal (no incluido): FS-4 no momentáneo, controladora FS-10
69
70 71
72
Introduction
Blackstar IDシリーズ・ アンプリファイアをお買い上げいただき、誠にあり
がとうございます。
この製品は、他の当社の製品同様、我々の世界的にもトップレベルの設計チ
ームにより、長期間にわたる徹底した研究、調査を元に設計してあります。
英国ノーザンプトンを拠点とする、ブラックスター社は全員がミュージシャ
ンとしての経験があり、ギタリストのベストパフォーマンスを実現するため
の「究極のギターツール」を提供することを唯一の目的としています。
全てのブラックスター製品は、品質、とりわけサウンドクオリティにおいて
妥協せず、多くの検査機関での試験、およびロードテスト(実施テスト)を
行っています。
このIDシリーズはユニークで革新的であり、直観的に操作できる伝統的なコ
ントロール、万能なプログラム機能を統合させたこれまでにない製品です。
ブラックスター製品を最大限に利用していただくために、このハンドブック
を注意深くお読みください。
さらにBlackstar製品に関して興味がある場合は、我々のウエブサイトにお立
寄りください。
URL: www.blackstaramps.com
ブラックスター・チームより
Features
主な特徴
ブラックスターは画期的なギターアンプによって、創立から5年でシーンの先
頭に到達しました。IDシリーズは弊社が技術研究と開発に7年以上かけて完成
させた、ユニークなコントロールでギタリストが自分自身のサウンドをカス
タムデザインし、保存することができるアンプです。だからこそ、ライブス
テージで、このアンプの最良の働きを見せることができるのです。
ブラックスターが特許請願中のTrue Valve Power(TVP)は6つの異なったパワ
ー管 EL84、6V6、EL34、KT66、6L6、KT88のレスポンスを出すことができ、真
空管特有のレスポンス、ダイナミクス、サグや歪み具合を余すところなく表
現し、本物の真空管アンプと同様のユニークな音圧を体験することができ、
これまでにないライブサウンドが楽しめます。True Valve Power - Valve
と同じラウドさがそこにあるのです。
ボイス・コントロールはCLEAN WARM、CLEAN BRIGHT、CRUNCH、SUPER
CRUNCH、OD1、OD2の6つの異なったセッティングができます。ブラックスター
の特許であるISFと合わせて使えば、あなたの思い描いているトーンを正確に
表現することが出来ます。
エフェクト・セクションはスタジオ・クオリティの品質を持たせたモジュレ
ーション、ディレイ、リバーブから構成され、サウンドと同様に記憶させる
ことが出来ます。
より詳細な編集やパッチの記憶はブラックスターが提供する専用ソフトウェ
ア
(Blackstar INSIDER Software)
を使って行うことが出来ます。オンライン・
コミュニティ経由でパッチの共有や、アップロード、ダウンロードが出来
ます。USBコネクター経由でアンプから直接あなたのコンピュータにレコー
ディングすることが出来ます。エミュレーテット、MP3ライン・インを搭載
し、MIDI フットスイッチにも対応しています。
ユニークなボイス・コントロール、特許取得済のISF、特許請願中のTrue
Valve Power(TVP)を活用すれば、IDアンプに無類の柔軟性と使い勝手の良さ
が得られ、その結果としてあなたの記憶にある音をデザインし、真空管と同
じラウドなサウンドを生み出すことが出来るのです。個性はパワーなので
す。
All electrical and electronic products should be disposed of separately from the municipal waste stream via designated collection facilities appointed by the government or the local authorities.
73
74
Demo Mode
アンプ購入後、またはファクトリー・リセットの後に最初にスイッチを入れ
た場合、アンプはデモ・モードになっています。マニュアル・モードのよう
に、アンプからのサウンドはフロントパネルのノブのポジションに合致しま
す。全てのエフェクト, TVPはオフ状態です。
全てのパッチ位置は工場出荷時のセッティングになっています。デモ・モー
ドでパッチを作成し記憶させることができますが、オリジナルの工場出荷時
のパッチとセッティングはスイッチを切って再び入れるごとに再読み込みさ
れます。
デモ・モードから抜け出す場合はアンプがオンの状態でMANUALボタン(19)を
押し続けてください。BANK LED (20)が赤 からオレンジ、緑に変わればデ
モ・モードが解除されたことになります。BANK LEDが一巡して点灯しスイッ
チ・オフになる前にMANUALボタンを解除するとアンプは再びデモ・モードに
戻ります。
ブラックスター専用ソフト・ウェア
(Blackstar INSIDER Software)
を使用しても
デモ・モードから抜け出すことができます。プログラム画面のDemo Modeラベ
ルをクリックしDisableを選択して下さい。
Factory Reset
アンプを工場出荷時のパッチの状態にいつでも戻すことが出来ます。
アンプがオンの時にMOD, DLY, REVボタンを同時に押し続けてください。BANK
LEDが点灯し緑からオレンジ、赤へと変わりファクトリー・リセットになった
ことを示します。
これはトータルで2秒かかります。もしBANK LEDが一巡し、スイッチ・オフす
る前にMOD,DLY,REVボタンを解除してしまうと、リセットへの操作はキャンセ
ルされ、アンプは元の状態に戻ります。
この操作が完了すれば、アンプは、デモ・モードに再び戻ります。
重要:この操作はあらゆるユーザー・コンテンツを上書きしてしまうのでご
注意下さい。
75
76
Front Panel
1. Input
楽器用シールドコードを使ってギターを接続します。
2. Voice
プリアンプのボイシングとレンジをクリーンなサウンドからオーバードライ
ブ・サウンドまで変化させます 。
Clean Warm – ダイナミックで上質なクリーン
Clean Bright – ハードに弾くと軽く歪むブティック・トーン
Crunch – 中程度のゲインを持たせたクラシックなオーバードライブ
Super Crunch – さらにゲインとパンチを効かせたサウンド
OD 1 – 中程度のパワーアンプ・ダンピングを持つホットロッドなオーバードライブ
OD 2 – よりミッドレンジを強化させたホットロッドなオーバードライブ
パッチをストアするとセッティングが保存されます
3. Gain
オーバードライブやディストーションをコントロールします。
左方向に回すとエッジの効いたクリーンなサウンドで、右方向に回すに従い、ドライ
ブさが増したクランチなトーンになり、回しきったポジションでフルにディストーシ
ョンの効いたトーンになります。
パッチをストアするとセッティングが保存されます。
4. Volume
プリアンプの音量を調節します。右方向に回すに従い音量が大きくなります。ポジショ
ンを高いレベルにすると真空管特有のパワー、ディストーション、コンプレッションが
現れます。この効果はTVPの設定によってそれぞれ変わってきます。
パッチをストアするとセッティングが保存されます。
5. Bass
低域をコントロールします。このアンプは進歩したトーンシェイプ回路搭載により左方
向に回すとタイトな切れ味良いサウンド、右方向に回すと暖かみのあるどっしりとした
トーンになります。
パッチをストアするとセッティングが保存されます。
6. Treble
高域をコントロールします。左方向に回すとウォームなサウンドになり、右方向に回す
に従って明るさが増していきます。右方向に回しきったセッティングではアグレシッブ
で切れのあるサウンドになります。
パッチをストアするとセッティングが保存されます。
EL84
6V6
EL34
KT66
6L6
KT88
7. ISF
ISFはベース、ミドル、トレブルと連動して働き、独自
の音色が選べます。左方向に回すとタイトなボトムエン
ドとアグレッシブなミドルのモダンなアメリカンサウン
ド、右方向に回すと、より箱鳴り感のあるブリティッシ
ュサウンドになります。
USA
従来のコンツアーやパラメトリックEQと異なり、ベー
ス、ミドル、トレブルのコントロールはトラディショナ
ルなアンプのように効果的に働きます。そのため音楽的に使える効果があります。
パッチをストアするとセッティングが保存されます。
UK
8. TVP (True Valve Power) Selector
ブラックスターが特許出願中のTrue Valve Power(TVP)は6つの異なったパワー管 EL84
、6V6、EL34、KT66、6L6、KT88のレスポンスを再現します。つまり真空管特有のレス
ポンス、ダイナミクス、サグのフィーリングや歪み具合を余すところなく表現し、本
物の真空管アンプと同じような音圧を体験することができます。TVPを活用してこれま
でにないライブサウンドが楽しめます。True Valve Power - まさに真空管と同じラ
ウド感を発揮します。
TVPはサウンド・キャラクターにコンプレッションを効かせたり、柔らかい音色からダ
イナミックで締まった音色にまでに自由に変化させることが可能です。
コンプレッションを効かせたベルの様なフルボディClass Aサウンド
コンプレッションを効かせた高域とタイトな中域のクリスピーなClass Aサウンド
フルボディでソフトな歪み具合のクラシックなブリティッシュClass A/Bサウンド
ホットにバイアスされリッチで暖かいビンテージ・ブリティッシュ・サウンド
高域と低域を拡げたタイトでダイナミックなClass A/Bサウンド
低域を強化したタイトで太くダイナミックなClass A/Bサウンド
例:EL84からKT88に設定を変更するとコンプレッションとオーバードライブの量が減
少します。さらに2つのクリーンサウンドのいずれかを選択すればコンプレッションと
オーバードライブがGAINコントロールを操作することによって変化することが分かる
でしょう。
パッチをストアするとセッティングが保存されます。
9. TVP (True Valve Power) Switch
ボタンを押してTVPのオン/オフを切り替えます。ボタン内のLEDが点灯しTVPがオンに
なったことを示します。LEDが消えている場合TVPは作動せずTVPセレクターは機能しま
せん。
パッチをストアするとセッティングが保存されます。
注意:TVPをオフにした場合、パワーアンプはリニア・レスポンス(デジタルアンプ)
となりTVPが作り出す真空管特有のサグ、コンプレッション、パワー感を得ることはで
きません。
Effects
3種12タイプのスタジオ・クオリティのエフェクトを搭載しています。
77
78
10. MOD (Modulation)
モジュレーションのオン/オフ/エフェクト編集の切替スイッチです。
パッチをストアするとセッティングが保存されます。
11. DLY (Delay)
ディレイのオン/オフ/エフェクト編集の切替スイッチです。
パッチをストアするとセッティングが保存されます。
12. REV (Reverb)
リバーブのオン/オフ/エフェクト編集の切替スイッチです。
パッチをストアするとセッティングが保存されます。
3つのEffect スイッチの点灯するLEDの色によってEffect の状態を確認することがで
きます。
LED
消灯
赤
緑
状態
エフェクト・オフ
エフェクト・オン。 編集は不可。
エフェクト・オン。 編集可能
(14,15,16参照)
内容
エフェクトは作動していません。
エフェクトは作動しますが、フロントパネル
のEFFECTコントロールの影響を受けません。
エフェクトは作動し、フロントパネルの
EFFECTコントロール位置の影響を受けます。
Effectスイッチを押すたびにエフェクトの状態が以下の順番で切り替わります。
エフェクト・オフ
エフェクト・オン。
編集は不可(赤))
エフェクト・オン。
編集可能(緑)
エフェクトがオンになりエフェクト効果がかかります。 前に設定したエ
フェクト数値が反映されます。
引き続きエフェクトはオンの状態でエフェクト・パラメータの編集がで
きます(14, 15, 16参照)。
エフェクト・オフになります。 他のエフェクトがオンであれば、そのエ
フェクトがかかります。
一度に編集できるのは、1つのエフェクトだけです。
13. Effect Type
選択しているエフェクト (MOD, DLY, REV)のエフェクトの種類の変更と、パラメータの
編集をします。
それぞれのセグメント内に異なったエフェクトを4タイプ備えています。
作動中のエフェクトにはLEDが点灯します。セグメント内でエフェクトのパラメータの
変更が出来ます。変更出来るパラメータについては下記表を参照ください。
パッチをストアするとセッティングが保存されます。
14. Effect Level
エフェクト・パラメータを変更します。
MODとDLYに限ってはTAP ボタン(15)を押しながらLEVELコントロールを回すことによって rate/timeを変更することができます。変更出来るパラメータについては下記表を参照くだ
さい。
パッチをストアするとセッティングが保存されます。
15. Tap
選択しているエフェクトのrate/timeを変更します。ボタンをタップする間隔でrate/ timeをセットします。
セットするとセットしたrate/timeでLEDが点滅します。
変更出来るパラメータについては下記表を参照ください。
Effects Table
エフェクト TYPEノブ・パラメータ
MODULATION
1.フェイザー
2.フランジャー
3.コーラス
4.トレモロ
DELAY
1.リニア
2.アナログ
3.テープ
4.マルチ
REVERB
1.ルーム
2.ホール
3.スプリング
4.プレート
ミックス
フィードバック
ミックス
フリケンシー
フィードバック
フィードバック
フィードバック
フィードバック
サイズ
サイズ
サイズ
サイズ
LEVELノブ・パラメータ T A P ス イ ッ チ ・
パラメータ
デプス
デプス
デプス
モジュレーション・デプス
スピード
スピード
スピード
スピード
ディレイ・レベル
ディレイ・レベル
ディレイ・レベル
ディレイ・レベル
タイム
タイム
タイム
タイム
リバーブ・レベル
リバーブ・レベル
リバーブ・レベル
リバーブ・レベル
-
-
-
-
パッチをストアするとセッティングが保存されます。
16. Master Volume
アンプから出る音量を調整します。
• 使用する環境に応じてセットするため、設定は保存できません。
17. Power Switch
アンプON/OFFを切り替えるスイッチです。 白い点は、アンプがオンであることを意味
します.
注意:デモ・モードで電源OFFにし、再びONにすると工場出荷時のセッティングに戻り
ます。デモ・モードではない場合、バックアップが行われた時の状態になります。
18. USB
Widows PCやMacからのUSBケーブルをここに接続できます。
ブラックスター専用ソフトウェア(Blackstar INSIDER Software)をブラックスター・ウ
ェブサイトからダウンロードでき、多くの機能を楽しむことが出来ます。
79
80
詳しくは、Page 98 (ハンドブック後半)に記載するUSB Audio の項目をご覧ください。
注意:このアンプはレコーディング・ソフト内のオーディオ・キャプチャー・デバイス
としてパーソナル・コンピュータの画面に現れます。
19. Manual
このスイッチを押してマニュアル・モードと現在選択しているパッチの切り替えを行い
ます。
マ ニ ュ ア ル ・ モ ー ド で は サ ウ ン ド は 現 在 の ノ ブ 位 置 に 反 映 さ れ ま す 。 こ れ は
Voice、Gain、Volume、Bass、Middle、 Treble、 ISFとTVPに適用されます。TVPのON/
OFF状況は切り替える前のパッチの状態が引き継がれます。あらゆるエフェクト はマニ
ュアル・モードに切り替えるとOFFになります。
マニュアル・モードでは全てのコントロールは外部機器(ブラックスター専用ソフトウ
ェア(Blackstar INSIDER Software)、フットスイッチ、MIDIコントローラ)でも変更で
きますが、この場合サウンドはフロントパネルのノブ位置に左右されません。
チューナー・モード
MANUAL ボタンを3秒以上押し続けると内蔵のチューナーが作動します。リコール・イン
ジケータ LED(28)が点滅しアンプがチューナー・モードに入ったことを知らせます。工
場出荷時の状態ではチューナー・モードでは出力はミュートされます。
MANUAL, BANK, CHANNELのLEDが最も近い音程を弾くと点灯して知らせます。
Bank LED
CH1 LED
CH2 LED
CH3 LED
CH4 LED
1弦、6弦 (工場出荷時はE, low/highです)
2 弦
3 弦
4 弦
5 弦
MOD, DLY, REV LEDが弾いた音程がどれぐらい近いかを点灯して知らせます。
MOD LED 赤
DLY LED 緑
REV LED 赤
音程がシャープ (音程が高い)
音程が合っている状態
音程がフラット (音程が低い)
チューナー・モードではフロントパネルの他のLEDはオフになります。
フロントパネルのあらゆるボタン、または接続した、あらゆるフットスイッチのボタン
を押すとチューナー・モードから抜け出します。
20. Bank
このボタン使用し、以下の3つのBANK切替を行います。
Bank 1 2
Bank 2 3
Bank 3 1
緑のLEDでBANK 1, オレンジのLEDでBANK 2, 赤のLEDでBANK 3を示します。
注意:最初の3つのBANKだけがフロントパネルから選択できます。外部コントローラ(
例 Blackstar INSIDER Software, フットコントローラ)からBANK 4またはそれ以上
のBANKを作動させると、BANK LEDは点灯しませんがCH LEDはパッチの位置を示し続けま
す。
例:
パッチ11では BANK LEDは赤く点灯し、CH 3 LEDが点灯します。
外部コントローラーでバンク15を選択すると、パッチ15を選択します。 - その場合
バンクLEDが消灯しチャンネル3が点灯します。
マニュアル・モードではBANK LEDは点灯しません
チャンネル番号は記憶されますので、BANKをスクロールすると選択したBANK内で相当す
るパッチが選択されます。
21 – 24. Channels 1-4
CH 1を選択した場合、現在のBANK内にある最初のパッチが作動します。
CH 2を選択した場合、現在のBANK内にある2番目のパッチが 作動します。
CH 3を選択した場合、現在のBANK内にある3番目のパッチが作動します。
CH 4を選択した場合、現在のBANK内にある4番目のパッチが作動します。
25. Footswitch
以下のサポートしているフットスイッチをここに接続して下さい。
1ボタンフットスイッチ
1ボタンのラッチ式フットスイッチ(例:FS-4)を接続し、フロントパネルで選択した
BANKのCH 1とCH2を切り替えることが出来ます。
ラッチオフ(例 FS-4のLEDが消灯の場合)CH 1が作動。
ラッチオン(例 FS-4のLEDが点灯の場合)CH 2が作動
ブラックスター FS-10フットコントローラ
マルチ機能を持たせたフットスイッチで、全パッチへのアクセスが可能で、エフェクト
切替、パッチ切替が行えます。
MIDIフットコントローラ
お手持ちのフットコントローラーで機能が決定されます。
26. MP3/Line In
MP3/CDプレーヤーなどの外部音源を接続する端子です。外部音源の音量は外部機器側で
調節してください。
注意:モノラル接続です。
27. Emulated Output
この端子からは、ギターアンプのスピーカーやキャビネットサウンドをシミュレーショ
ンした回路を通ったサウンドが出力されます。録音機器やミキサーに直接接続する場合
に使用します。
ステレオ効果をご利用する場合は、ミキサーや録音機器の2つのチャンネルに接続する
ためにステレオY字ケーブルをご使用ください(図参照)。
81
82
この端子はモノラル・ギター用ケーブルにも対応しています。
高品質ケーブルのご使用を推奨します。
VOLUME (4)でEMULATED OUTの出力を調整します。MASTER VOLUMEは接続されたスピーカ
ー・キャビネットのみに作用します。
注意:サイレント状態でレコーディングする場合、MASTER VOLUMEをゼロにセットしま
す。
スピーカーを接続せずにEMULATED OUTからレコーディングすることも可能です。
まず、アンプのスピーカー端子に何も接続されていないことを確認して下さい。
保護回路に負担がかかり故障の原因になります。
28. Recall Indicator
リコール・インジケータは現在のパラメータとフロントパネルのノブ位置との間に差異
があるかどうかを知らせます。例えば、異なったパッチへ変更すると、フロントパネル
のコントロールノブは必ずしも実際に聞こえているセッティングを反映しません。
調整する際の極端なレベル変更を避けるため、フロントパネルのノブが現在のパラメー
タの位置になるまで操作はサウンドに反映されません。ノブがその位置になるとリコー
ル・インジケータは2回点滅して、ノブのコントロールが有効となり効果のコントロー
ルが出来るようになります。
現在のパッチに保存されているコントロールの値を通過するたびにリコール・インジケ
ータが2回点滅しますので、記憶している値を簡単に確認することができます。
リコールはGain、Volume、Bass、Middle、TrebleとISFに対して働きます。
チューナー が作動している時もリコール・インジケータは継続して点滅します。
Rear Panel
1. Mains Input
付属の電源コードを接続する端子です。電源コードを差し込む前に、リア・パネルに記
載されている電圧や周波数が日本国内で使用する基準に適しているかを確認してくださ
い。不明な場合は、アフターサービスまでお問い合わせください。
プログラムに関して
現在のサウンドをパッチに記憶させる場合、
1. 4つのCHボタンのいずれかを1秒押し続けると、全てのCH LEDが点滅を始めます。
2. BANKボタンを押して3つのBANK (緑、オレンジ、赤)を切り替え、保存先のBANKを選
択します。
3. パッチの保存先を選択するため、保存するCHボタンを選択し押します。
選択したBANKのLEDの色が点灯し、新しいパッチが作動します。
GREEN BANK = パッチ1-4
ORANGE BANK = パッチ 5-8
RED BANK = パッチ9-12
アンプのコントロールは記憶させる過程であれば、どの段階でもパッチを編集するこ
とが出来ます。
記憶させる過程をキャンセルするにはMANUALボタンを押してください。
アンプは前の段階に戻ります。
パッチを記憶させると、同じ場所に入っていた情報は上書きされます。
パッチはブラックスター専用ソフトウェア(Blackstar INSIDER Software)やブラック
スター FS-10フットコントローラでも保存することが出来ます。
パッチの呼び出し
使用するパッチのCHボタンを押します。
BANKボタンを押して緑 -オレンジ-赤の色を切り替え、BANKを決定します。
CHはそのままで、現在のBANKで呼応するパッチを読み込みます。
パッチはブラックスター専用ソフトウェア(Blackstar INSIDER Software)あるいは接
続されたフットスイッチでも呼び出すことができます。
83
84
USB Audio
標準的なオーディオ・ドライバーをPCやMacと接続する場合に使用します。
特定のドライバーは要求されません。
アンプはレコーディング・ソフト内のオーディオ・キャプチャーとして認識されます。
オーディオ・フォーマットは Blackstar INSIDER Softwareを通して変更でき、2つのタ
イプから選べます。
スピーカーエミュレイテッド・ステレオエフェクト・オーディオ・チャンネル
2 x モノラル・オーディオ・チャンネル
- 左チャンネル – エフェクトされたアンプからの信号
- 右チャンネル – 未加工のギター・シグナル
リアンプ・モード
リアンプ
Blackstar INSIDER Software を経由してアンプはリアンプ・モードにスイッチできま
す。
これはプログラムできないセッティングで、USBケーブルを抜くかアンプ本体のスイッ
チをオフにした時に、スイッチがオフになります。
リアンプ・ モードにした場合、アンプはUSBを経由してパソコンにプリレコードされた
ギターのドライ・モノラル信号を受け入れることが出来ます。
さらにアンプで加工した信号を送り返すことができます。この戻されたデータは接続
されたPCやMacで使用しているレコーディング・ソフトでキャプチャーすることが出来
ます。
ファームウェアのアップデート
ブラックスター専用ソフトウェア(Blackstar INSIDER Software)を通して、ファーム
ウェアのアップデートが行なえます。アップデートに要する時間はおおよそ60-120秒
です。
アンプをUSBに接続し旧バージョンのファームウェアと認識されると、最新ファイルを
インストールするようメッセージがディスプレイされます。アップデート中、アンプの
コントロールはできません。アップデートの作業中はTAP LEDが点滅します。
ファームウェア・アップデート中はアンプの電源スイッチを切らないでください。
アップデートの間にアンプの電源がオフになると、再び電源をオンにしてもコントロー
ルは効かずアンプから音は出ません。TAP LEDが点滅した場合は、アンプに有効なファ
ームウェアが搭載されていないことを示します。
有効なファームウェアを入手するためにはアンプをブラックスター専用ソフトウェアに
接続しなければなりません。
もしブラックスター専用ソフトウェアがアンプの状態を感知すれば必要に応じて自動的
にアップデートを開始します。
Technical Specification
ID:15TVP
Power: 15 Watts
Weight (kg): 11
Dimensions (mm): 450(W) x 417(H) x 220(D)
Footswitch (not supplied): FS-4 latching footswitch, FS-10 footcontroller
ID:30TVP
Power: 30 Watts
Weight (kg): 13
Dimensions (mm): 500(W) x 460(H) x 250(D)
Footswitch (not supplied): FS-4 latching footswitch, FS-10 footcontroller
85
Manufacturer: Blackstar Amplification Date: 11-07-12
Model: ID:Series Version:
+---------------------+-----------------+----------------+---------------------+-----------------+
: Function ... : Transmitted : Recognized : Remarks : Value :
: : : : : :
+---------------------+-----------------+----------------+---------------------+-----------------+
:Basic Default : No : YES : Incoming message : 1-6 :
:Channel : : : channel. : :
: : : : Receiving messages : :
: : : : on ALL channels can : :
: : : : be set via the GUI : :
: +------------+-----------------+----------------+---------------------+-----------------:
: Changed : No : No : - : - :
+---------------------+-----------------+----------------+---------------------:-----------------+
:Mode Default : NO : NO : - : - :
: Messages : NO : NO : - : - :
: Altered : NO : NO : - : - :
+---------------------+-----------------+----------------+---------------------:-----------------+
:Note : : : : :
:Number True Voice : NO : NO : - : - :
+---------------------+-----------------+----------------+---------------------:-----------------+
:Velocity Note On : NO : NO : - : - :
: Note Off : NO : NO : - : - :
+---------------------+-----------------+----------------+---------------------:-----------------+
:After : : : : :
:Touch Keys : NO : NO : - : - :
: Channels : NO : NO : - : - :
+---------------------+-----------------+----------------+---------------------:-----------------+
:Pitch Bender - : NO : NO : - : - :
+---------------------+-----------------+----------------+---------------------:-----------------+
:Control : 5 : NO : YES : Voice : 0-5 :
:Changes : 6 : NO : YES : Gain : 0-127 :
: : 7 : NO : YES : Volume : 0-127 :
: : 8 : NO : YES : Bass : 0-127 :
: : 9 : NO : YES : Mid : 0-127 :
: : 10 : NO : YES : Treble : 0-127 :
: : 11 : NO : YES : ISF : 0-127 :
: : 12 : NO : YES : TVP : 0-5 :
: : 13 : NO : YES : Modulation Effect : 0-3 :
: : : : : Select : :
: : 14 : NO : YES : Modulation Adjust 1 : 0-127 :
: : 15 : NO : YES : Modulation Adjust 2 : 0-127 :
: : 16 : NO : YES : Modulation Level : 0-127 :
: : 17 : NO : YES : Modulation Rate : 0-127 :
: : 18 : NO : YES : Delay Effect Select : 0-3 :
: : 19 : NO : YES : Delay Adjust 1 : 0-127 :
: : 20 : NO : YES : Delay Adjust 2 : 0-127 :
: : 21 : NO : YES : Delay Level : 0-127 :
: : 22 : NO : YES : Reverb Effect Select: 0-3 :
: : 23 : NO : YES : Reverb Adjust 1 : 0-127 :
: : 24 : NO : YES : Reverb Adjust 2 : 0-127 :
: : 25 : NO : YES : Reverb Level : 0-127 :
: : 26 : NO : YES : Resonance : 0-127 :
: : 27 : NO : YES : Presence : 0-127 :
: : 64 : NO : YES : Modulation On/Off : 0-63 = OFF :
: : : : : : 64-127 = ON :
: : 65 : NO : YES : Delay On/Off : 0-63 = OFF :
: : : : : : 64-127 = ON :
: : 66 : NO : YES : Reverb On/Off : 0-63 = OFF :
: : : : : : 64-127 = ON :
: : 67 : NO : YES : TVP On/Off : 0-63 = OFF :
: : : : : : 64-127 = ON :
: : 68 : NO : YES : Delay Tap : DATA IGNORED :
: : : : : Duration : (Incoming :
: : : : : : message used :
: : : : : : as the trigger) :
: : 199 : NO : YES : Save Current Patch : DATA IGNORED :
: : : : : : (Incoming :
: : : : : : message used :
: : : : : : as the trigger) :
+---------------------+-----------------+----------------+---------------------+-----------------+
:Program : : : : :
:Change True# : NO : YES : Patch to recal : :
: : : : (Patch # 1-128) : 0-127 :
+---------------------+-----------------+----------------+---------------------+-----------------+
:System Exclusive : NO : NO : - : - :
+---------------------+-----------------+----------------+---------------------+-----------------+
:System Song Pos. : NO : NO : - : - :
:Common Song Sel. : NO : NO : - : - :
: Tune : NO : NO : - : - :
+---------------------+-----------------+----------------+---------------------+-----------------+
:System Clock : NO : NO : - : - :
:Real Commands : NO : NO : - : - :
:Time : - : - : - : - :
+---------------------+-----------------+----------------+---------------------:-----------------+
:AUX Local : NO : NO : - : - :
:Messages ON/OFF : : : - : - :
: All Notes : NO : NO : - : - :
: Off : : : - : - :
: Active Sense : NO : NO : - : - :
: Reset : NO : NO : - : - :
+---------------------+-----------------+----------------+---------------------+-----------------+
Manufacturer: Blackstar Amplification Date: 11-07-12
Model: ID:Series Version:
+---------------------+-----------------+----------------+---------------------+-----------------+
: Function ... : Transmitted : Recognized : Remarks : Value :
: : : : : :
+---------------------+-----------------+----------------+---------------------+-----------------+
:Basic Default : No : YES : Incoming message : 1-6 :
:Channel : : : channel. : :
: : : : Receiving messages : :
: : : : on ALL channels can : :
: : : : be set via the GUI : :
: +------------+-----------------+----------------+---------------------+-----------------:
: Changed : No : No : - : - :
+---------------------+-----------------+----------------+---------------------:-----------------+
:Mode Default : NO : NO : - : - :
: Messages : NO : NO : - : - :
: Altered : NO : NO : - : - :
+---------------------+-----------------+----------------+---------------------:-----------------+
:Note : : : : :
:Number True Voice : NO : NO : - : - :
+---------------------+-----------------+----------------+---------------------:-----------------+
:Velocity Note On : NO : NO : - : - :
: Note Off : NO : NO : - : - :
+---------------------+-----------------+----------------+---------------------:-----------------+
:After : : : : :
:Touch Keys : NO : NO : - : - :
: Channels : NO : NO : - : - :
+---------------------+-----------------+----------------+---------------------:-----------------+
:Pitch Bender - : NO : NO : - : - :
+---------------------+-----------------+----------------+---------------------:-----------------+
:Control : 5 : NO : YES : Voice : 0-5 :
:Changes : 6 : NO : YES : Gain : 0-127 :
: : 7 : NO : YES : Volume : 0-127 :
: : 8 : NO : YES : Bass : 0-127 :
: : 9 : NO : YES : Mid : 0-127 :
: : 10 : NO : YES : Treble : 0-127 :
: : 11 : NO : YES : ISF : 0-127 :
: : 12 : NO : YES : TVP : 0-5 :
: : 13 : NO : YES : Modulation Effect : 0-3 :
: : : : : Select : :
: : 14 : NO : YES : Modulation Adjust 1 : 0-127 :
: : 15 : NO : YES : Modulation Adjust 2 : 0-127 :
: : 16 : NO : YES : Modulation Level : 0-127 :
: : 17 : NO : YES : Modulation Rate : 0-127 :
: : 18 : NO : YES : Delay Effect Select : 0-3 :
: : 19 : NO : YES : Delay Adjust 1 : 0-127 :
: : 20 : NO : YES : Delay Adjust 2 : 0-127 :
: : 21 : NO : YES : Delay Level : 0-127 :
: : 22 : NO : YES : Reverb Effect Select: 0-3 :
: : 23 : NO : YES : Reverb Adjust 1 : 0-127 :
: : 24 : NO : YES : Reverb Adjust 2 : 0-127 :
: : 25 : NO : YES : Reverb Level : 0-127 :
: : 26 : NO : YES : Resonance : 0-127 :
: : 27 : NO : YES : Presence : 0-127 :
: : 64 : NO : YES : Modulation On/Off : 0-63 = OFF :
: : : : : : 64-127 = ON :
: : 65 : NO : YES : Delay On/Off : 0-63 = OFF :
: : : : : : 64-127 = ON :
: : 66 : NO : YES : Reverb On/Off : 0-63 = OFF :
: : : : : : 64-127 = ON :
: : 67 : NO : YES : TVP On/Off : 0-63 = OFF :
: : : : : : 64-127 = ON :
: : 68 : NO : YES : Delay Tap : DATA IGNORED :
: : : : : Duration : (Incoming :
: : : : : : message used :
: : : : : : as the trigger) :
: : 199 : NO : YES : Save Current Patch : DATA IGNORED :
: : : : : : (Incoming :
: : : : : : message used :
: : : : : : as the trigger) :
+---------------------+-----------------+----------------+---------------------+-----------------+
:Program : : : : :
:Change True# : NO : YES : Patch to recal : :
: : : : (Patch # 1-128) : 0-127 :
+---------------------+-----------------+----------------+---------------------+-----------------+
:System Exclusive : NO : NO : - : - :
+---------------------+-----------------+----------------+---------------------+-----------------+
:System Song Pos. : NO : NO : - : - :
:Common Song Sel. : NO : NO : - : - :
: Tune : NO : NO : - : - :
+---------------------+-----------------+----------------+---------------------+-----------------+
:System Clock : NO : NO : - : - :
:Real Commands : NO : NO : - : - :
:Time : - : - : - : - :
+---------------------+-----------------+----------------+---------------------:-----------------+
:AUX Local : NO : NO : - : - :
:Messages ON/OFF : : : - : - :
: All Notes : NO : NO : - : - :
: Off : : : - : - :
: Active Sense : NO : NO : - : - :
: Reset : NO : NO : - : - :
+---------------------+-----------------+----------------+---------------------+-----------------+
87
ID:15TVP Front Panel
EM. OUT
& PHONES
MP3 /
LINE IN
OD 1
SUPER
CRUNCH
CRUNCH
OD 2
INPUT
CLEAN
BRIGHT
CLEAN
WARM
VOICE GAIN VOLUME
0
LEVEL
10 0
LEVEL
10 0
EQUALISATION
10 0 10 0 10
KT66
6L6
KT88
EL34
6V6
EL84
TVP
MOD
DLY
REV
USB MANUAL BANK CH 1 CH 2 CH 3 CH 4 TVP TAP
1
EFFECTS
2
3
TYPE
4
0
LEVEL
10
MASTER
POWER
0 10
FOOTSWITCH
ID:15TVP Rear Panel
1
89
ID:30TVP Front Panel
EM. OUT
& PHONES
MP3 /
LINE IN
OD 1
SUPER
CRUNCH
INPUT
OD 2
CRUNCH
CLEAN
BRIGHT
CLEAN
WARM
VOICE GAIN VOLUME EQUALISATION
0
LEVEL
10 0
LEVEL
10 0 10 0 10 0 10
KT66
6L6
KT88
EL34
6V6
EL84
TVP
MOD
DLY
REV
USB MANUAL BANK CH 1 CH 2 CH 3 CH 4 TVP TAP
1
EFFECTS
2
3
TYPE
4
0
LEVEL
10
MASTER
0 10
POWER
FOOTSWITCH
ID:30TVP Rear Panel
1
91
92 93
94 95
Blackstar Amplification Ltd, Beckett House, 14 Billing Road, Northampton, NN1 5AW, UK
For the latest information go to: www.blackstaramps.com
Whilst the information contained herein is correct at the time of publication, due to our policy of constant improvement and development, Blackstar Amplification Ltd reserves the right to alter specifications without prior notice.
ID:15TVP and ID:30TVP
Owner’s Manual
Designed and Engineered by
Blackstar Amplification UK
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project