SW-MOTECH QUICK-LOCK 12V BMW 6 Power Socket User Manual

Below you will find brief information for Power Socket QUICK-LOCK 12V BMW 6. This manual describes how to install and use the QUICK-LOCK Power Socket 12V on your motorbike, including how to connect it to the battery and how to secure the cable routing. Pay attention to the torque specifications for each screw size, as well as proper cable management and the use of magnets near the socket. Make sure the cable is not damaged and that the handlebars have full movement without any obstructions from the cable. The manual also emphasizes the importance of consulting a qualified mechanic if you are not comfortable completing the assembly yourself.

PDF Download

Document

TRE.00.475.120
Revision: 00
QUICK-LOCK Power Socket 12V BMW 6
QUICK-LOCK Power Socket 12V BMW 6
!
Achtung: beim Verschrauben des
QUICK-LOCK Power Sockets 12V auf
den Tank auf Widerstand achten,
da bei zuviel Druck der
Tankdeckelring besch&auml;digt werden
kann.
Attention: Be careful when mounting
the QUICK-LOCK Power Socket 12V.
Using too much pressure to tighten
the screws can damage the fuel
tank cap.
!
Bitte pr&uuml;fen Sie den festen Sitz der
Schrauben im Rahmen der &uuml;blichen
Fahrzeugwartung.
Please check if all screws are
correctly mounted with every
maintanance.
!
Achtung: Schraubenart und L&auml;nge
m&uuml;ssen ggf. selbst ermittelt werden,
da diese je nach Motorradtyp variieren.
Attention: The type of screw and
length may vary depending upon
motorcycle.
!
Achtung: der Abstand zwischen den
Rasthaken mu&szlig; mindestens 70 mm
betragen, ggf. die Rasthaken beidseitig
nach Au&szlig;en dr&uuml;cken.
Attention: the space between the
hook-ends must be at least 70mm
wide, if necessary push the hookends outward while tightening so the
resulting distance between them is
at least 70mm.
70 m
m
SW-MOTECH GmbH &amp; Co. KG
Bahnhofstrasse 44d
35282 Rauschenberg
-GermanyTel.: ++ 49 (0) 6425 8168 00
Fax: ++ 49 (0) 6425 8168 10
www.sw-motech.com
Locked torque
! Anzugsmoment
M4
3,0 Nm
M5
4,5 Nm
Achtung: wir &uuml;berM6 4,5 Nm
nehmen keine Haftung
bei Br&uuml;chen durch zu festes Anziehen
der Schrauben.
Attention: we do not guarantee
against breakage due to
overtightening of screws.
!
Achtung: folgende Punkte sind
bei der Benutzung des QUICKLOCK Power Socket 12V
unbedingt zu beachten:
Attention: Pay attention to the
following points if you want to
use the QUICK-LOCK Power
Socket 12V:
- Nutzen Sie den QUICK-LOCK Power
Socket 12V nur in Verbindung mit
einem entsprechenden Oberring von
SW-MOTECH.
- Use the QUICK-LOCK Power Socket
12V only with the upper tankrings
from SW-MOTECH.
- Achten Sie auf eine korrekte
Kabelisolierung. Sollte eine
Besch&auml;digung vorliegen, tauschen Sie
diese Komponente umgehend aus.
- Halten Sie Magneten aller Art von
der Rastbolzen&ouml;ffnung des QUICKLOCK Power Socket 12V fern, um
Kurzschl&uuml;sse zu vermeiden.
- Achten Sie bei der Verlegung des
Kabels darauf, dass der volle
Lenkeinschlag ohne Behinderung
m&ouml;glich ist. Stellen Sie sicher, dass
das Kabel keinen Kontakt zu hei&szlig;en
oder beweglichen Komponenten des
Motors hat. Befestigen Sie das Relais
an einem geeigneten Ort (z. B. am
Rahmen). Schlie&szlig;en Sie die
Kabelenden wie in der Detailzeichnung
dargestellt an der Batterie an.
- Die Voraussetzung f&uuml;r die Montage
ist nat&uuml;rlich eine gewisse technische
Erfahrung. Wenn Sie sich nicht
sicher sind, wie man eine bestimmte
Arbeit ausf&uuml;hrt, sollten Sie diese
Ihrem Fachh&auml;ndler &uuml;berlassen.
- Make sure the electric cable is not
demaged. If the cable is damaged,
replace the component.
- To avoid a short-circuit don't use
any magnets near the lock bolt hole
of the QUICK-LOCK Power Socket.
- Be carefull when routing the cable.
Make sure full movement of the
handlebars is possible. The cable
must not contact any hot or moving
parts of the motorcycle. Fasten the
relay to a safe and secure location
(e.g. at the frame). Attach the cable
ends as represented in the detail
drawing of the battery.
- If you do not feel technically
qualified to install this product on
your own, please consult your
nearest motorcycle-dealer.
1
!
QUICK LOCK
Power Socket 12V
QUICK LOCK
Power Socket 12V
Anschluss an Fahrzeugbatterie.
Connection to batterie.
rot /
red
schwarz /
black
TKE.00.475.001_B
Anzahl/ Pcs.
2
Beispiel / example
1
Innensechskantschraube
Hexagon Socket Screw
3
Innensechskantschraube
Hexagon Socket Screw
2 3
2 3
M5 x 35
Anzahl/ Pcs.
DIN 912
4
M5 x 40
Anzahl/ Pcs.
DIN 912
2 3
4
2 3
1
QUICK-LOCK Power Socket 12V
Kabel
Cable
Relais
Relay
Batterie
Battery
Fahrtrichtung
Driving direction
TRE.00.475.120
">

Hello! I am an AI chatbot specifically trained to assist you with the QUICK-LOCK 12V BMW 6 Power Socket User Manual. I have thoroughly reviewed the document and can help you locate the exact information you need or explain the content in clear and simple terms. Whether you’re looking for guidance on specific features, troubleshooting steps, or general usage, feel free to ask your questions. The more details you provide about your concerns or needs, the more accurately and effectively I can assist you!

Show related prompts

Assistant typing

Assistant terminated

Key Features

QUICK-LOCK mounting system
12V power outlet
Waterproof and dustproof
Secure cable routing
Easy installation

Frequently Answers and Questions

What is the purpose of the QUICK-LOCK Power Socket 12V?

The QUICK-LOCK Power Socket 12V provides a convenient and secure way to connect a 12V device, such as a GPS unit, phone charger, or other accessories, to your motorcycle's battery.

How do I install the QUICK-LOCK Power Socket 12V?

Follow the step-by-step instructions provided in the user manual. Pay close attention to the torque specifications, cable routing, and placement of the relay. Consult a qualified mechanic if you are not comfortable with the installation process.

What type of screws are needed for installation?

The type and length of screws may vary depending on your motorcycle model. It is advisable to consult the user manual or your motorcycle dealer for the appropriate screw type and length.