DS-510
Setup Guide
Oct, 2014
silex LUN!
technology WA101800XX
Thank you for purchasing the USB Device бегуег "05-510".
This Setup Guide provides information on how to configure
and use the DS-510 in your network.
C Package Contents В
L] 25-510
[I Warranty Booklet
[] Rubber foot (4pcs)
[1 AC adaptor
[] Setup Guide (this document)
C Name of Parts )
Za
Е черт ba
© ©
Power connector
POWER LED
Network port
LINK LED
Push Switch
USB port
Before You Begin
C Downloading the necessary items
KE Access the URL below from the computer you are using to
configure the DS-510.
USA : silex technology america, Inc.
URL : http://www.silexamerica.com/
Europe : silex technology europe GmbH
URL : http://www.silexeurope.com/
2 Go to the Support page and select the product model.
| Product Model DS-510
В This section explains how to download the necessary utilities and user's manual from our website.
Download the utilities and user's manual below and extract them on
your computer.
Device Server Setup
SX Virtual Link
Utility
Users Manual | DS-510 User's Manual
There are Windows version and Macintosh version for each utility.
Please download the one appropriate for your operating system.
Step 1. Power on and Configuration
C 1-1. Power on
How to power on the DS-510 is explained:
KE The following items are required.
Ethernet HUB
Network cable USB cable
Connect the DS-510 to the USB device a
using a USB cable (2).
* There are USB devices not supported due
to the driver specification. Please check
the latest compatibility information on our
website.
* Only 1 device can run on bus power.
* If the DS-510 has been used in another network,
reset it to factory default first (see below for
Oo <= details).
)
Connect the DS-510 to the Ethernet
HUB using a network cable (1).
Connect the AC adaptor to the DS-510 (3)
and the AC plug to the power outlet (4).
Check that POWER LED and LINK LED
turn on (5).
El If the USB device requires external
power, use the power supply cable (6).
* Be sure to use the AC adaptor that came
with the DS-510.
C Factory Default Configuration
Remove the AC plug from the power
outlet (1).
=
J
Network
Push and hold the push switch with a
fine tipped object such as a pen or
pencil while inserting the AC plug
back into the power outlet (2).
Continue holding.
3 When the LINK LED (Green) starts
to blink (3),the factory default
configuration is complete.
Release the push switch.
N
C 1-2. Configuration
How to configure the DS-510 is explained:
By default, the DS-510 is configured to automatically obtain an IP
address from the DHCP server. If the DHCP server is installed on
your network, the configuration will not be necessary. In such a
case, go on to install the SX Virtual Link (see the back).
When you want to configure the IP address manually or you are not
sure if there is the DHCP server on your network, move on to KB .
KE Extract the Device Server Setup file
that you have downloaded at
Downloading the necessary items.
* Before moving on to KB, please temporarily disable
the firewall function of the computer you use for
configuration. Some of the methods to disable the
firewall are provided in the FAQ on our homepage.
- Standard Windows XP firewall
- Commercial security software's firewall function
| Ethernet HUB
—_ \
Network Cable
(1) Power Outlet
e
a B= o e
E oy
(3)
AC Adaptor
USB Cable |(2)
A POWER LED
(5)
LINK LED
USB Device
~
Power Outlet
(3)
ID
LINK LED m to
(So
AC Adaptor
1
(2)
Push Switch
See the contained PDF manual (Device
Server Configuration) to configure the
DS-510 using the Device Server Setup
utility.
Step 2. Using the USB Devices over Network
C 2-1. Installing the SX Virtual Link )
The SX Virtual Link is the software program to make a
communication between your computer and the USB
. . If the SX Virtual Link is not installed to your computer, Extract the SX Virtual Link file that you have downloaded See the contained PDF manual (SX Virtual Link Installation) to
devices connected to the device server. install it by following the instructions in this section. iB at Downloading the necessary items. install the SX Virtual Link.
To use the USB devices over the network, you have to
connect to or disconnect from it using the SX Virtual Link.
The SX Virtual Link installer will restart your computer after it is
installed. Make sure that you finished all software programs on your
computer before starting the installation.
C 2-2. Basic Use of the SX Virtual Link )
Starting the SX Virtual Link ТО CE»
Click the application icon (6) in the task tray Click the application icon (6 ) in the Dock or
or click Start - (All) Programs - SX Virtual click Macintosh HD - Applications - SX
Link - SX Virtual Link. Virtual Link. |
Con necting the USB devices Select a USB device and click the Connect button ( EJ) ). | Windows ) | Macintosh ) 2 The Plug and Play function automatically creates an
The USB device can be connected when the status icon appropriate environment to use the selected device.
. . [ Y lis displayed. e
* When using the USB device for the first time, you may (@ sxvirtuai int PS (A sx virtual Link Elo The USB device will be ready to use once the status
need to install the device driver for that USB device. or UB y ob eo = icon has changed to [ @ 1. See the operating manual
e evice can also be connecte selectin . Y yema
To install the driver, refer to the operating manual that and double-clicking it on the SX Virtual Linie 9 <u ) that came with your USB device for how to use it.
came with the USB device, or follow the instructions on
ВН * If a device server is not displayed on a list, please click
the screen displayed after clicking the Connect button the Refresh button ( [21 ).
in the SX Virtual Link.
* Only one device can be connected at a time. When
* Do not unplug the USB cable or network cable, or click Ms e uN by another compute ihe
the Disconnect button ( gy ) on the SX Virtual Link Status Icon | 15 disprayed, which means that the
while the USB device is in use. USB device is not available now.
N J
Disconnecting the USB devices | Windows ec»
SX Virtual Lin
When you have finished using the USB device 9
, ; o ! Y irtual Lin ee SX Virtual Link lt 25
disconnect the device by selecting it and Deas — ©
clicking the Disconnect button ( Y). 7 eee Y quen |
sos are connected оаН, | ( SP D vues )
* The USB device can also be disconnected by selecting
and double-clicking it on the SX Virtual Link.
(User Registration ) D\ (Customer Support )
Please complete user registration after you finish the setup. USA : silex technology america. Inc
User registration is required to provide you better technical ° ! °
support and services. E-mail : [email protected]
http://www.silex.jp/register/ URL : http://www.silexamerica.com/
For user registration, a Serial Number is required. Phone : 1-866-765-8761
The Serial Number is the last 6-digits of the Ethernet Europe: silex technology europe GmbH
Address(12-digits total) which can be found on the E-mail : [email protected]
bottom of the unit. .
URL : http://www.silexeurope.com/
E le: If the Eth t Add is "84:25:3F:00:11:22" the Serial
are "DOT Le Phone : +49-(0)2151-65009-0
\_ Number will be "001122", | \_
Accessing Online Help
Click the Help button ( ) and
select Help from the menu displayed.
@ Help
silex technology web site
FAQ Page
(# About SX Virtual Link
1
~
">
