Intellinet Wireless 150N Portable 3G Router Quick Install Guide
Intellinet 524803 is a versatile and powerful device that combines the functionality of a wireless router with the convenience of a portable 3G connection. With its compact size and rechargeable battery, it's perfect for staying connected while on the go or in areas with limited internet access. The 524803 also features a built-in Ethernet port, allowing you to connect wired devices such as gaming consoles or smart TVs for a stable and reliable connection.
Advertisement
Advertisement
Guide
Model 524803
English
DEutsch
Español
FRançais polsKi italiano
INT-524803-QIG-ML1-1009-03-0
Wireless 150N Portable 3G Router • Quick Install Guide English
Thank you for purchasing the INTELLINET NETWORK SOLUTIONS ™ Wireless 150n
Portable 3G Router, Model 524803.
This guide presents the basic steps to set up and operate this device. For detailed instructions and specifications, refer to the user manual on the CD enclosed with this product or at www.intellinet-network.com.
Package Contents
• Wireless 150N Portable 3G Router
• Quick install guide, plus user manual on CD
• Power adapter
• Built-in rechargable Li-ion battery
• Ethernet Cat5 RJ45 cable: 1.0 m (3 ft.) and USB extension cable: 1.0 m (3 ft.)
• Carrying case and car charger
HARDWARE SETUP / CONNECTIONS
Charging the Battery
Before using the router, the battery needs to be charged. Charging the battery takes about four hours.
1. Remove the battery Cover Battery
compartment cover on
the back of the router,
insert the included
battery, then replace the
cover, sliding it until the latch
snaps securely back in place.
2. Plug the included power adapter into an AC
outlet or an automobile’s auxiliary power outlet,
PWR/CHG
LED
then connect it to the mini USB port on the router
(DC In). While the router battery is charging, the
PWR/CHG LED lights orange, then turns green when
the router battery is fully charged.
3. On the left side panel, set the On/Off switch to On. CAUTION:
Always switch the router off before removing the battery,
and only use the battery and power adapter included with
this router, as other types could be dangerous and damage
the router.
Power adapter
DC
In
Network Connections
If needed, visit www.intellinet-network.com for a complete list of compatible
3G USB modems.
2
English
1. Connect your 3G / 3.5G USB modem to the USB port on the top
panel of the router.
2. Connect your computer to the Ethernet port
on the right side panel of the router. NOTE:
USB port
It’s recommended that you use a cable
connection through the Ethernet port for the
router’s initial configuration. The PWR/CHG
LED should light green and the Ethernet
LED should be on if the computer or other
Modem
network device connected to the router’s Ethernet port is turned on and connected
properly.
NETWORk SETUP
The following steps are for the preliminary network setup of the router using a Web browser, which will make the router operational and ready for advanced configuration based on procedures in the user manual. NOTE: Screen images of other Windows operating systems are similar. Some screen images have been modified to fit the format of this guide.
1. Set your computer to
obtain an IP address from
a wireless router: Click
“Start” (usually located in
the lower-left corner of your
PC desktop), then Control
Panel; double-click Network
Connections, then double-
click Local Area Connection;
and lastly, on the Local Area
Connection Status screen,
click “Properties.”
English
3
2. When the Local Area
Connection Properties
screen appears, select
“Internet Protocol (TCP/IP),”
then click “Properties.”
3. Select “Obtain an IP
address automatically” and
“Obtain DNS server address
automatically,” then click
“OK.”
4. Once the IP address setup
is complete, click “Start” on
the desktop again, then
click “Run.” At the first DOS
prompt, enter “cmd” and
click “OK.”
4
English
5. When the next prompt screen appears, enter “ipconfig,” then press <Enter> on your
keyboard. Note the IP address and default gateway.
6. Open the Web browser and enter
the IP address of the router in the
address bar. When the prompt
screen at right appears, enter
“admin” (the default entry) in the
User name text field; and “1234”
(the default entry), in the Password
text field. Click “OK” to access the
Web management interface of the
router.
HERE!
7. When the main menu screen of the Web management interface displays, click “Quick
Setup” on the left.
English
5
8. When the subsequent Time Zone screen displays, select your local time zone from
the drop-down menu and click “Next.”
9. When the subsequent Broadband Type screen displays, select “3/3.5G” from among
the Internet connection options, then click “Next.”
10. Enter the Internet connection parameters required by your 3G/3.5G service provider,
then click “OK.”
6
English
11. With the Basic Settings screen displayed, make the selections/entries you prefer,
then click “Next.”
12. To protect your wireless network, it’s recommended that the security be enabled.
Select a security type from the drop-down menu, enter the encryption key, then
click “OK.”
13. When the prompt appears to restart the system, click “Apply.” A status message
will display, indicating that the router will be ready for operation in approximately
30 seconds. Once the router is ready for use, connect to any Internet site or open
any Internet application to check that they’re working properly.
NOTE: For detailed instructions about configuring all the useful features and options available with this Wireless 150N Portable 3G Router, refer to the user manual on the included CD.
English
7
Wireless 150N Portable 3G Router • Kurzanleitung Deutsch
Vielen Dank für den Kauf des INTELLINET NETWORK SOLUTIONS ™ Wireless 150n
Portable 3G Router, Modell 524803.
Diese Kurzanleitung zeigt die grundlegenden Schritte zur Einrichtung und
Inbetriebnahme dieses Geräts. Für genauere Anweisungen nutzen Sie bitte das beiliegende Handbuch auf CD oder auf www.intellinet-network.com.
Lieferumfang
• Wireless 150N Portable 3G Router
• Kurzanleitung plus Handbuch auf CD
• Netzteil
• Aufladbarer Lithium-Ionen-Akku
• Cat5 RJ45-Kabel: 1,0 m und USB-Verlängerungskabel: 1,0 m
• Tasche und Kfz-Ladekabel
HARDWAREINSTAllATION / ANSCHlüSSE
Akku aufladen
Bevor Sie den Router verwenden, laden Sie den Akku bitte vollständig auf. Die Aufladung nimmt etwa vier Stunden in Anspruch.
1. Entfernen Sie die Abdeckung Akku
Akkuabdeckung auf der
Rückseite des Routers,
legen Sie den Akku ein,
bringen Sie die Abdeckung
wieder an.
2. Verbinden Sie das beiliegende Netzteil mit
einer Steckdose oder einem Kfz-Stromanschluss,
dann mit dem Mini-USB-Port des Routers “(DC In)”.
PWR/CHG
LED
Während der Akku aufgeladen wird, leuchtet die
“PWR/CHG”-LED orange und wechselt zu Grün
sobald der Akku vollständig geladen ist.
3. Stellen Sie den Ein/Aus-Schalter auf “On”. ACHTUNG:
Schalten Sie den Router immer aus, bevor Sie den Akku,
entfernen und verwenden Sie nur Netzteil und Akku aus
dem Lieferumfang dieses Routers, durch Fremdzubehör
kann das Gerät evtl. Schaden nehmen.
Netzteil
DC
In
Netzwerkverbindungen
Sollten Sie eine Liste aller kompatiblen 3G-USB-Modems benötigen, finden Sie diese unter www.intellinet-network.com.
8
DEutsch
1. Verbinden Sie Ihr 3G / 3.5G USB-Modem mit dem USB-Port an der
Kopfseite des Routers.
2. Verbinden Sie Ihren Computer mit dem Ethernet-Port
an der rechten Seite des Routers. HINWEIS:
USB-Port
Wir empfehlen die Verwendung einer
Kabelverbindung über den Ethernet-Port bei
der erstmaligen Konfiguration. Die PWR/CHG-
LED sollte grün leuchten und die Ethernet-
LED sollte leuchten, wenn der am
Modem
Ethernet-Port angeschlossene Computer bzw. das Netzwerkgerät eingeschaltet wird
und korrekt verbunden ist.
NETzWERk EINRICHTEN
Die folgenden Schritte beschreiben die Netzwerkeinrichtung des Routers über einen
Webbrowser, mit der Sie den Router betriebsbereit machen und die Basis für fortgeschrittene Einstellungen mit Hilfe des Handbuchs schaffen. HINWEIS: Die Oberfläche anderer Windows-Versionen ist ähnlich. Manche Screenshots wurden an das Format dieses Handbuchs angepasst.
1. Konfigurieren Sie Ihren PC
so, dass er eine IP-Adresse
vom Wireless Router erhält:
Klicken Sie auf “Start” (in der
linken unteren Ecke Ihres
Desktops), dann auf
Systemsteuerung;
doppelklicken Sie auf
Netzwerkverbindungen,
dann auf LAN-Verbindung
und auf dem folgenden
Statusfenster schließlich
auf “Eigenschaften”.
DEutsch
9
2. Im Eigenschaftenfenster
markieren Sie “Internet
Protocol (TCP/IP),” dann
klicken Sie auf
“Eigenschaften”.
3. Wählen Sie “IP-Adresse
automatisch beziehen” und
“DNS-Serveradresse
automatisch beziehen” dann
klicken Sie auf “OK.”
4. Sobald die
IP-Adresseinstellungen
vollständig sind, klicken Sie
auf Ihrem Desktop erneut
auf “Start”, dann auf
“Ausführen”. Geben Sie in
der Leiste “cmd” ein und
klicken Sie auf “OK.”
10
DEutsch
5. Im folgenden Fenster geben Sie “ipconfig” ein, dann und bestätigen Sie mit der
Enter-Taste. Notieren Sie sich die Zahlen bei IP-Adresse und Standardgateway.
6. Öffnen Sie Ihren Webbrowser und
geben Sie die IP-Adresse des
Routers in der Adresszeile ein. In der
folgenden Eingabemaske (s. rechts),
geben Sie “admin”
(Standardbenutzername) als
Benutzernamen und “1234”
(Standardpasswort), als Passwort
ein. Klicken Sie auf “OK”, um die
Web-Benutzeroberfläche des
Routers aufzurufen.
HERE!
7. Nachdem das Hauptmenüfenster der Web-Benutzeroberfläche geöffnet wurde,
klicken Sie links auf “Quick Setup”.
DEutsch
11
8. Im folgenden Zeitzonenfenster, wählen Sie Ihre lokale Zeitzone aus dem Drop-Down
-Menü und klicken Sie auf “Next.”
9. Im folgenden Breitbandverbindungsfenster, wählen Sie “3/3.5G” aus den Internet
verbindungsoptionen, dann klicken Sie auf “Next.”
10. Geben Sie die Internetverbindungsdaten ein, die Sie von Ihrem 3G/3.5G-Provider
erhalten haben, dann klicken Sie auf “OK.”
12
DEutsch
11. Im folgenden Grundeinstellungsfenster, nehmen Sie Ihre bevorzugten Einstellungen
vor, dann klicken Sie auf “Next.”
12. Um Ihr Wireless Netzwerk zu schützen, empfehlen wir, die Verschlüsselung zu
aktivieren. Wählen Sie eine Verschlüsselungsart aus dem Drop-Down-Menü, geben
Sie den Schlüssel ein, dann klicken Sie auf “OK.”
13. Im folgenden Schritt wird das System neugestartet. Klicken Sie auf “Apply”
[Übernehmen]. Eine Statusnachricht erscheint, die anzeigt, dass der Router in ca. 30
Sekunden betriebsbereit ist. Öffnen Sie eine Internetseite oder eine beliebige
Online-Anwendung, um zu prüfen, ob die Internetverbindung korrekt funktioniert.
HINWEIS: Weitere Informationen zu den Einstellungen und Features sowie nützliche
Tipps zu diesem Wireless 150N Portable 3G Router finden Sie im Handbuch auf der beiliegenden CD.
DEutsch
13
Ruteador Inalámbrico Portátil 3G 150 N • Guía de Instalación Rápida Español
Gracias por comprar el Ruteador Inalámbrico Portátil 3G 150 N INTELLINET NETWORK solutions ™ , modelo 524803.
Esta guía presenta los pasos básicos para instalar y operar este dispositivo. Para obtener instrucciones detalladas y especificaciones, consulte el manual de usuario en el CD adjunto ó en www.intellinet-network.com.
Contenido del Paquete
• Ruteador Inalámbrico Portátil 3G 150 N
• Guia rapida de instalación, manual del usuario en CD
• Adapatador de corriente
• Batería de ión de litio recargable
• Cable Ethernet Cat5 RJ45: 1,0 m (3 ft.) y cable USB extensión: 1,0 m (3 ft.)
• Carcasa y cargador para el auto
INSTAlACION DE HARDWARE / CONEXIONES
Cargando la Bateria
Antes de usar el router, la batería necesita ser cargada. La carga de la batería dura unas cuatro horas.
1. Retire la tapa del Tapa Batería
compartimiento de la
parte trasera del router,
inserte la bateria incluida,
coloque de nuevo la tapa
deslizandola hasta que la estaña
se asiente en su lugar.
2. Conecte el adaptador de alimentación incluido a
una toma de CA o la salida de un automóvil de
PWR/CHG
LED
DC
alimentación auxiliar, a continuación, conéctelo al
puerto mini USB en el router (DC). Mientras que la
batería del router se está cargando, la PWR / CHG se
liminara el LED de color naranja, cambia a verde cuando
Adaptador de alimentación
la batería está completamente cargada.
3. En el panel del lado izquierdo, coloque el interruptor
On / Off en On. PRECAUCION: Siempre apague el router
antes de retirar la bateria, sólo utilice el adaptador de
batería y alimentación que se incluye, usar otro tipo podria dañar el router.
Conexiones de red
Si es necesario, visite www.intellinet-network.com para obtener una lista completa de compatibilidad de modems 3G USB.
14
Español
1. Conecte su modem USB 3G / 3.5G al puerto USB
en la parte superior del router.
2. Conecte su computadora al puerto Ethernet
en el panel lateral derecho del router. NOTA:
Se recomienda que utilice un cable conexión
a través del puerto Ethernet para la
configuración inicial del router. El LED
PWR / CHG debera estar en verde y el
USB puerta
LED Ethernet estara encendido si la PC
Modem
y otro dispositivo de red estan conectado al puerto Ethernet del router esta encendido
y conectado correctamente.
INTAlACION DE RED
Los pasos siguientesle guiaran para la configuración en red del router mediante un navegador Web, lo que hará que el router sea funcional y listo para la configuración avanzada, basada en los procedimientos del manual de usuario. NOTA: Las imágenes de pantalla de otros sistemas operativos de Windows son similares. Algunas imágenes de la pantalla se han modificado para ajustarse al formato de esta guía.
1. Configure su PC para que
obtenga una dirección IP
de un router inalambrico:
haga clic en “Inicio”
(normalmente se encuentra
en la esquina inferior
izquierda de su PC), vaya al
Panel de Control; haga doble
clic en Conexiones de red,
haga doble clic en Conexion
de area local; y por ultimo,
en la conexión de area local
de la pantalla de estado,
haga clic en “Propiedades.”
Español
15
2. Cuando en pantalla se
muestre Propiedades de
conexiones de area local,
seleccione “Protocolo de
Internet (TCP/IP),”
entonces haga clic en
“Propiedades.”
3. Seleccione “Obtener una
dirección IP automatica” y
“Obtenga una dirección DNS
automatica,” haga clic en
“Aceptar.”
4. Una vez que la configuración,
de la dirección IP es
completada, haga clic en
“Inicio” en el escritorio de
nuevo, entonces haga clic en
“Ejecutar” vaya a la linea de
comandos de DOS, escriba
“cmd” y haga clic en
“Aceptar.”
16
Español
5. Cuando aparezca la pantalla del sistema, escriba “ipconfig” y luego presione <Enter>
en el teclado. Anote la dirección IP y puerta de enlace predeterminada.
6. Abra un navegador Web y escriba
la dirección IP del router en la barra
de direcciones. Cuando aparezca la
pantalla de la derecha, escriba
“admin” (predeterminado) en el
campo Usuario; y “1234”
(Predeterminado), en el campo de
contraseña. Haga clic “Aceptar” para
accesar a la interfaz web del router.
HERE!
7. Cuando la pantalla del menú principal de la interfaz de gestión Web, haga clic en
“Quick Setup” a la izquierda.
Español
17
8. Cuando en la pantalla siguiente aparece la pantalla de zona horaria, seleccione su
zona horaria local en el menú desplegable y haga clic en “Siguiente”.
9. Cuando en la siguiente pantalla se muestre Broadband Type, seleccione “3/3.5G”
entre las opciones de conexión a internet, haga clic en “Next.”
10. Introduzca los parámetros de conexión a Internet proporcionados por su proveedor
de servicios 3G/3.5G, a continuación, haga clic en “OK”.
18
Español
11. Cuando se muestre en la pantalla Basic Settings, realice las selecciones / entradas
que desees, a continuación, haga clic en “Next”.
12. Para proteger su red inalámbrica, se recomienda que la seguridad esté habilitada.
Seleccione un tipo de seguridad en el menú desplegable, introduzca la clave de
cifrado, a continuación, haga clic en “OK”.
13. Cuando aparezca el mensaje para reiniciar el sistema, haga clic en “Aceptar”. Un
mensaje de estado mostrará, lo que indica que el router estará listo para la operación
en aproximadamente 30 segundos. Una vez que el router está listo para su uso,
conectarse a cualquier sitio de Internet o abrir cualquier aplicación de Internet para
comprobar que está funcionando correctamente.
NOTA: Para obtener instrucciones detalladas sobre la configuración de todas las características útiles y opciones disponibles con este el Ruteador Inalámbrico Portátil
3G 150 N, consulte el manual del usuario en el CD incluido.
Español
19
Routeur portable sans fil 150N 3G • Guide d’installation rapide Français
Merci d’avoir acheté l’INTELLINET NETWORK SOLUTIONS ™ Routeur portable sans fil
150N 3G, modèle 524803.
Ce guide décrit les bases pour configurer et opérer cet appareil. Pour des instructions et spécifications détailées, veuillez lire le manuel de l’utilisation sur le CD inclus ou sur
www.intellinet-network.com.
Contenu du pack
• Routeur portable sans fil 150N 3G
• Guide d’installation rapide, plus manuel de l’utilisateur sur le CD
• Adaptateur secteur
• Batterie Li-ion rechargeable
• Câble Ethernet Cat5 RJ45: 1,0 m et rallonge USB: 1,0 m
• Sacoche de transport et chargeur de voiture
INSTAllATION mATéRIEllE / CONNEXIONS
Charger la batterie
Avant utiliser le routeur, la batterie doit être chargée. Ce processus dure environ quatre heures.
1. Enlevez le couvercle de Couvercle Batterie
la batterie au dessous
du routeur, insérez la
batterie incluse, puis
remettez le couvercle.
Assurez-vous qu’il est
encliqueté fermement.
2. Branchez l’adaptateur secteur à une prise de
courant ou une alimentation électrique de voiture,
DEL PWR/
CHG
puis connectez-le au port USB mini du routeur
(“DC In”). Pendant que la batterie du routeur charge,
le DEL “PWR/CHG” s’allume orange, puis s’allume
vert dès qu’il est chargé complètement.
3. Mettez l’interrupteur d’alimentation sur “On”. ATTENTION:
Toujours éteignez le routeur avant que vous sortiez la
batterie. N’utilisez que la batterie et l’adaptateur fournis
avec ce produit, d’autres types pourraient endommager le
routeur.
Adaptateur secteur
DC
In
Connexions de réseau
Visitez www.intellinet-network.com s’il faut une liste complète de modems USB 3G.
20
FRançais
1. Connectez votre modem USB 3G / 3.5G au port USB du routeur.
2. Connectez votre ordinateur au port Ethernet du routeur.
NOTE: Nous vous recommandons utiliser une
connexion filaire au port Ethernet pour la
Port USB
configuration initiale. Le DEL “PWR/CHG”
doit être allumé vert et le DEL Ethernet
doit être allumé si l’ordinateur ou d’autres
appareils réseau sont démarrés et
connectés proprement au port Ethernet
du routeur.
Modem
CONfIgURATION DU RéSEAU
Les étapes suivantes décrivent la configuration réseau du routeur via un navigateur
Web avec lequel vous faites le routeur prêt à l’emploi et créez la base pour la configuration avancée à l’aide des instructions dans le manuel de l’utilisateur. NOTE: Les surfaces des autres versions Windows sont similaires. Quelques images ont été adaptées au format de ce guide.
1. Ajustez votre ordinateur
afin qu’il obtient une adresse
IP d’un routeur sans fil:
Cliquez sur “Démarrer” (à
gauche en bas sur votre
bureau), puis sur le panneau
de configuration; double-
cliquez sur Connexions de
réseau puis sur Connexion
de réseau local et ensuite,
dans la fenêtre d’état,
cliquez sur “Propriétés.”
FRançais
21
2. La fenêtre de connexions du
réseau local s’affiche.
Sélectionnez “Protocole
Internet (TCP/IP),” puis
cliquez sur “Propriétés.”
3. Sélectionnez “Obtenir une
adresse IP
automatiquement” et
“Obtenir une adresse de
serveur DNS
automatiquement”, puis
cliquez sur “OK.”
4. Dès que la configuration
d’adresse est complète,
cliquez sur “Démarrer” à
nouveau, puis sur Exécuter
et entrez “cmd”, puis cliquez
sur “OK.”
22
FRançais
5. Une nouvelle fenêtre s’affiche. Entrez “ipconfig,” puis appuyez sur <Enter> sur votre
clavier. Retenez l’adresse IP et la passerelle par défaut..
6. Démarrez votre navigateur Web et
entrez l’adresse IP du routeur dans
la barre d’adresse. Une masque de
saisie s’affiche (cf. à droite), entrez
“admin” (nom d’utilisateur par
défaut) dans le champ du nom
d’utilisateur et “1234” (mot de passe
par défaut) dans le champ du mot
de passe. Cliquez sur “OK” afin
d’accéder l’interface Web du
routeur.
HERE!
7. Le menu principal de l’interface Web s’affiche, cliquez sur “Quick Setup” à gauche.
FRançais
23
8. La fenêtre du fuseau horaire s’affiche; sélectionnez votre fuseau horaire local de la
liste déroulante et cliquez sur “Next.”
9. La fenêtre de type large bande s’affiche; sélectionnez “3/3.5G” des options de
connexion Internet, puis cliquez sur “Next.”
10. Entrez les paramètres de connexion que vous avez obtenus de votre fournisseur
d’accès à Internet 3G/3.5G, puis cliquez sur “OK.”
24
FRançais
11. La fenêtre des options principales s’affiche, sélectionnez vos paramètres préférés,
puis cliquez sur “Next.”
12. Afin de protéger votre réseau sans fil, nous vous recommandons activer le cryptage.
Sélectionnez un type de cryptage de la liste déroulante, entrez la clé de cryptage,
puis cliquez sur “OK.”
13. À cette étape le système est réinitialisé. Cliquez sur “Apply”. Un message d’état
apparaît, indiquant que le routeur sera prêt à l’emploi en environ 30 secondes. Dès
que ce processus est complet, accédez à un site Web ou démarrez une application
Internet à votre choix afin de vérifier que la connexion Internet est établie proprement.
NOTE: Pour des informations complémentaires sur l’installation, la configuration et les fonctions du Routeur portable sans fil 150N 3G, veuillez lire le manuel de l’utilisation sur le CD fourni avec ce produit.
FRançais
25
Router bezprzewodowy 150N 3G przenośny • Instrukcja szybkiej instalacji Polski
Dziękujemy za zakup Przenośnego Bezprzewodowego Routera 150N 3G INTELLINET nEtWoRK solutions ™ , model 524803.
Ta instrukcja prezentuje podstawowe kroki podłączenia i instalacji urządzenia. Aby uzyskać szczegółowe informacje techniczne oraz instrukcję użytkownika zapoznaj się zawartością płyty CD dołączonej do opakowania lub odwiedź stronę www.intellinet-network.com.
Zawartość opakowania
• Router bezprzewodowy 150N 3G przenośny
• Instrukcja szybkiej instalacji oraz instrukcja użytkownika na płycie CD
• Adapter zasilania
• Akumulator litowo-jonowy
• Kabel Ethernet RJ45 Cat5, 1m oraz przedłużacz USB, 1m
• Pokrowiec ochronny oraz ładowarka samochodowa
PODŁĄCzENIE / zŁĄCzA
Ładowanie akumulatora
Przed użyciem routera akumulator musi zostać naładowany. Ładowanie zajmuje około czterech godzin.
1. Zdejmij plastikową osłonkę Osłonka Akumulator
na spodniej części
routera, włóż do środka
dołączony akumulator, a
następnie załóż plastikową
osłonkę, upewniając się, że dobrze
dolega po pozostałej części routera.
2. Podłącz dołączony zasilacz do gniazda sieciowego
lub do gniazda zapalniczki samochodowej, a
Dioda
PWR/CHG
Wejście
DC
następnie podłącz kabel do portu mini USB (DC in)
routera. Podczas ładowania akumulatora dioda PWR/
CHG będzie świecić na pomarańczowo, zapalenie się
zielonej diody oznacza pełne naładowanie akumulatora.
3. Na bocznej części routera przełącznik On/Off ustaw na
pozycję On. WAŻNE: Zawsze przed wyciągnięciem
akumulatora należy wyłączyć router. Należy stosować tylko
i wyłącznie akumulator oraz zasilacz dostarczony wraz z
Zasilacz
routerem. Używanie innych typów akumulatorów oraz zasilaczy może być
niebezpieczne, może również doprowadzić do uszkodzenia routera.
26 polsKi
Podłączenie modemu
Odwiedź stronę www.intellinet-network.com aby sprawdzić listę kompatybilnych modemów USB 3G.
1. Podłącz swój modem USB 3G/3.5G do portu USB routera.
2. Połącz kablem Ethernet port karty sieciowej komputera z
portem RJ45 znajdującym się na prawej
bocznej części routera. UWAGA: Zaleca się,
aby podczas konfiguracji routera używać
Port USB
połączenia kablowego. Dioda PWR/CHG
powinna świecić na zielona. Jeśli router
jest prawidłowo połączony z kartą
sieciową komputera lub innym
Modem
urządzeniem sieciowym powinna również świecić dioda portu Ethernet.
USTAWIENIA SIECIOWE
Poniżej opisane kroki przedstawiają wstępną konfigurację sieci, potrzebną do zalogowania się do routera poprzez przeglądarkę internetową w celu dalszej konfiguracji urządzenia
(zapoznaj się z instrukcją użytkownika, aby poznać szczegóły). UWAGA: Konfiguracja we wszystkich wersjach Windows wygląda podobnie. Niektóre z przedstawionych obrazów zostały zmienione na potrzeby tego dokumentu.
1. Ustaw kartę sieciową na
automatyczne pozyskiwanie
adresu IP z bezprzewodowego
routera: Wciśnij kolejno
„Start”, następnie „Panel
sterowania” i wybierz
„Połączenia sieciowe”.
Następnie kliknij dwukrotnie
na ikonie „Połączenie lokalne”
i na karcie stanu połączenia
lokalnego wybierz
„Właściwości”.
polsKi
27
2. Na karcie właściwości
połączenia lokalnego zaznacz
składnik „Protokół internetowy
(TCP/IP)”, a następnie wybierz
„Właściwości”.
3. Na karcie właściwości
protokołu internetowego
(TCP/IP) zaznacz opcje
„Uzyskaj adres IP
automatycznie” oraz
„Uzyskaj adres serwera DNS
automatycznie” i wciśnij „OK.”
4. Gdy konfiguracja adresacji
jest zakończona, wciśnij
„Start”, a następnie polecenie
„Uruchom”. W okno, które się
pojawiło wpisz „cmd” i wciśnij
„OK”.
28 polsKi
5. W nowym DOS-owym oknie wpisz polecenie „ipconfig” i wciśnij „Enter”. Zapamiętaj
adres IP oraz adres bramy domyślnej.
6. Otwórz przeglądarkę internetową i
wpisz w pasek adresu domyślny
adres IP routera. Gdy pojawi się
okno logowania, w pole nazwy
użytkownika wpisz „admin”, a w
pole hasła wpisz „1234”. Wciśnij „OK”,
aby się zalogować.
HERE!
7. Po pojawieniu się menu routera w przeglądarce internetowej wybierz opcję „Quick
Setup” po lewej stronie ekranu.
polsKi
29
8. W nowym oknie ustawień czasu (Time Zone), wybierz z rozwijanej listy swoją
lokalizację, a następnie wciśnij „Next”.
9. W kolejnym oknie typu połączenia wybierz opcję „3/3.5G” i wciśnij „Next”.
10. Wpisz parametry logowania się do sieci 3G/3.5G i wciśnij OK. Wszystkie potrzebne
tutaj parametry otrzymasz od dostawcy swoich usług internetowych.
30 polsKi
11. Ustaw podstawowe parametry sieci bezprzewodowej i wciśnij „Next”.
12. Dla zapewnienia bezpieczeństwa sieci bezprzewodowej zaleca się włączenie
szyfrowania. Wybierz typ szyfrowania, wpisz klucz, a następnie wciśnij „OK.”
13. Po wyświetlenie monitu o ponowne uruchomienie urządzenia, wciśnij „Apply”.
Status będzie informował o gotowości routera do pracy w ciągu około 30 sekund.
Następnie należy otworzyć dowolną stronę internetową lub aplikację sieciową i
sprawdzić, czy jest połączenie sieciowe.
UWAGA: Aby uzyskać szczegółowe informacje na temat wszystkich przydatnych opcji i funkcji Przenośnego Bezprzewodowego Routera 150N 3G, zapoznaj się z instrukcją użytkownika znajdującą się na dołączonej płycie CD.
polsKi
31
Router 3G Wireless 150N Portatile • Guida Rapida Italiano
Grazie per aver scelto il Wireless 150N Portatile 3G Router INTELLINET NETWORK solutions ™ , modello 524803.
Questa guida fornisce le informazioni basilari per settare e far funzionare l’apparecchiatura.
Per istruzioni e specifiche dettagliate, fare riferimento al manuale d’istruzione nel CD incluso al prodotto o al sito www.intellinet-network.com.
Contenuto della confezione
• Router 3G Wireless 150N Portatile
• Guida rapida all’installazione , oltre al manuale d’istruzione sul CD
• Alimentatore
• Batteria agli Ioni litio ricaricabile inclusa
• Cavo di rete Cat5 RJ45: 1.0 m e prolunga USB: 1.0 m
• Borsetta da trasporto e caricatore da auto
SETTAggIO HARDWARE / CONNESSIONI
Ricarica della batteria
Prima di utilizzare il router, la batteria deve essere caricata. La carica della batteria richiede circa quattro ore.
1. Rimuovere il coperchio del Coperchio Batteria
compartimento della
batteria sul retro del
router, inserire la batteria
inclusa, quindi rimettere il
coperchio, facendolo scivolare fino
a quando si avverte che è avvenuto l’aggancio.
2. Collegare l’alimentatore incluso alla presa di
corrente o su una presa di alimentazione ausiliaria
Ingresso
DC
dell’automobile, quindi connetterlo alla porta mini
USB del router (DC In). Mentre la batteria del router si
carica, il LED PWR/CHG si illumina in arancione, quindi
diventa verde quando la carica è completa.
Alimentatore
3. Sul pannello laterale di sinistra, posizionare l’interruttore su
On. SI RACCOmANdA PRUdENzA: Spegnere sempre il
router prima di procedere alla rimozione della batteria.
Utilizzare solo la batteria e l’alimentatore incluso a questo
router, poiché altri tipi potrebbero essere pericolosi e causare danni al router.
Connessioni di rete
Se necessario, visitare il sito www.intellinet-network.com per una completa lista dei modem 3G USB compatibili.
32 italiano
1. Collegate il vostro modem USB 3G / 3.5G USB alla porta USB sul
pannello superiore del router.
2. Collegate il vostro computer alla porta Ethernet sul
pannello laterale sinistro del router. NOTA:
Porta USB
E’ consigliato utilizzare una connessione
via cavo attraverso la porta Ethernet per la
configurazione iniziale del router. Il LED
PWR/CHG LED dovrebbe illuminarsi in
verde e il LED dell’Ethernet dovrebbe
Modem
essere acceso se il computer o la periferica di rete connessa alla porta Ethernet del
router è accesa e collegata in modo corretto.
SETTAggIO DEllA RETE
I seguenti passaggi permettono un preliminare settaggio di rete del router usando un
Web browser, che renderà il router operativo e pronto per una configurazione avanzata basata sulle procedure del manuale d’istruzione. NOTA: Le immagini dello schermo di altri sistemi operativi Windows sono simili. Alcune immagini dello schermo sono state modificate per adeguarle al format di questa guida.
1. Settate il vostro computer
per ottenere un indirizzo IP
da un router wireless: Cliccare
“Start” (di solito posizionato
nell’angolo in basso a sinistra
della desktop del PC), quindi
“Control Panel”; fare doppio
clic su “ Network Connections “,
quindi doppio clic su “Local
Area Connection”; e alla fine,
sulla schermata della
Connessione area locale,
cliccare su “Properties”.
italiano
33
2. Quando sullo schermo
appaiono le Proprietà di
Connessione dell’area locale,
selezionare “Internet Protocol
(TCP/IP)”, quindi cliccare su
“Properties”.
3. Selezionare “Obtain an IP
address automatically” e
”Obtain DNS server address
automatically”, quindi cliccare
“OK.”
4. Appena il settaggio
dell’indirizzo IP è completo,
cliccare di nuovo “Start” sulla
desktop, quindi cliccare
“Run.” Alla prima prompt
DOS, inserire “cmd” e cliccare
“OK.”
34 italiano
5. Quando appare sullo schermo il successivo prompt, inserire “ipconfig,” quindi premere
<Enter> sulla tastiera. Annotare l’indirizzo IP e il gateway predefinito.
6. Aprire il Web browser ed inserire
l’indirizzo IP del router nella barra
dell’indirizzo. Quando la schermata
di prompt appare a destra, inserire
“admin” (voce predefinita) nel campo
di testo con il nome utente; e “1234”
(voce predefinita), nel campo di test
con la Password. Cliccare “OK” per
accedere all’interfaccia Web di
gestione del router.
HERE!
7. Quando sullo schermo appare il menu principale dell’interfaccia di gestione Web,
cliccare “Quick Setup” sulla sinistra.
italiano
35
8. Quando compare la schermata con Time Zone, selezionare il vostro fuso dal menù a
tendina e cliccare “Next.”
9. Quando appare la successive schermata “Broadband Type”, selezionare “3/3.5G” tra le
opzioni di connessioni Internet, quindi cliccare “Next.”
10. Inserire i parametri di connessione Internet richiesti dal vostro service provider 3G/
3.5G, quindi cliccare “OK.”
36 italiano
11. Quando viene visualizzato il “Basic Settings”, effettuare le selezioni desiderate, quindi
cliccare “Next.”
12. Per proteggere la vostra rete wireless, si raccomanda che la sicurezza sia attiva.
Selezionare un tipo di sicurezza dal menu a tendina, inserire la chiave di crittografia,
quindi cliccare “OK.”
13. Quando appare il prompt per riavviare il sistema, cliccare “Apply.” Un messaggio di
stato comparirà, indicando che il router sarà funzionante approssimativamente in
30 secondi. Appena il router è pronto all’uso, connettersi a qualsiasi sito Internet o
aprire un’applicazione Internet per verificare il corretto funzionamento.
NOTA: Per istruzioni dettagliate in merito alla configurazione di tutte caratteristiche utili e le opzioni disponibili con questo Router 3G Wireless 150N Portatile, fare riferimento al manuale d’istruzione presente nel CD incluso.
italiano
37
WASTE ELECTRICAL & ELECTRONIC EQUIPMENT
Disposal of Electric and Electronic Equipment
(applicable in the European Union and other European countries with separate collection systems)
ENGLISH
This symbol on the product or its packaging indicates that this product shall not be treated as household waste.
Instead, it should be taken to an applicable collection point for the recycling of electrical and electronic equipment. By ensuring this product is disposed of correctly, you will help prevent potential negative consequences to the environment and human health, which could otherwise be caused by inappropriate waste handling of this product. If your equipment contains easily removable batteries or accumulators, dispose of these separately according to your local requirements. The recycling of materials will help to conserve natural resources. For more detailed information about recycling of this product, contact your local city office, your household waste disposal service or the shop where you purchased this product. In countries outside of the EU: If you wish to discard this product, contact your local authorities and ask for the correct manner of disposal.
dEutSCH
Dieses auf dem Produkt oder der Verpackung angebrachte Symbol zeigt an, dass dieses Produkt nicht mit dem Hausmüll entsorgt werden darf. In Übereinstimmung mit der Richtlinie 2002/96/EG des Europäischen
Parlaments und des Rates über Elektro- und Elektronik-Altgeräte (WEEE) darf dieses Elektrogerät nicht im normalen Hausmüll oder dem Gelben Sack entsorgt werden. Wenn Sie dieses Produkt entsorgen möchten, bringen Sie es bitte zur Verkaufsstelle zurück oder zum Recycling-Sammelpunkt Ihrer Gemeinde.
ESPAñOL
Este símbolo en el producto o su embalaje indica que el producto no debe tratarse como residuo doméstico.
De conformidad con la Directiva 2002/96/CE de la UE sobre residuos de aparatos eléctricos y electrónicos
(RAEE), este producto eléctrico no puede desecha se con el resto de residuos no clasificados. Deshágase de este producto devolviéndolo al punta de venta o a un punta de recogida municipal para su reciclaje.
FRANçAIS
Ce symbole sur Ie produit ou son emballage signifie que ce produit ne doit pas être traité comme un déchet ménager. Conformément à la Directive 2002/96/EC sur les déchets d’équipements électriques et électroniques (DEEE), ce produit électrique ne doit en aucun cas être mis au rebut sous forme de déchet municipal non trié. Veuillez vous débarrasser de ce produit en Ie renvoyant à son point de vente ou au point de ramassage local dans votre municipalité, à des fins de recyclage.
ItALIANO
Questo simbolo sui prodotto o sulla relativa confezione indica che il prodotto non va trattato come un rifiuto domestico. In ottemperanza alla Direttiva UE 2002/96/EC sui rifiuti di apparecchiature elettriche ed elettroniche (RAEE), questa prodotto elettrico non deve essere smaltito come rifiuto municipale misto. Si prega di smaltire il prodotto riportandolo al punto vendita o al punto di raccolta municipale locale per un opportuno riciclaggio.
POLSkI
Jeśli na produkcie lub jego opakowaniu umieszczono ten symbol, wówczas w czasie utylizacji nie wolno wyrzucać tego produktu wraz z odpadami komunalnymi. Zgodnie z Dyrektywą Nr 2002/96/WE w sprawie zużytego sprzętu elektrycznego i elektronicznego (WEEE), niniejszego produktu elektrycznego nie wolno usuwać jako nie posortowanego odpadu komunalnego. Prosimy o usuniecie niniejszego produktu poprzez jego zwrot do punktu zakupu lub oddanie do miejscowego komunalnego punktu zbiórki odpadów przeznaczonych do recyklingu.
38
WARRANTY INFORMATION
ENGLISH: For warranty information, go to www.intellinet-network.com/warranty.
dEutSCH: Garantieinformationen finden Sie unter www.intellinet-network.com/warranty.
ESPAñOL: Si desea obtener información sobre la garantía, visite www.intellinet-network.com/warranty.
FRANçAIS: Pour consulter les informations sur la garantie, visitez www.intellinet-network.com/warranty.
POLSkI:
Informacje dotyczące gwarancji znajdują się na stronie www.intellinet-network.com/warranty.
ItALIANO: Per informazioni sulla garanzia, accedere a www.intellinet-network.com/warranty.
EN MéXICO: Poliza de Garantia INTELLINET — Datos del importador y responsable ante el consumidor
IC Intracom México, S.A. de C.V.
•
Av. Interceptor Poniente # 73, Col. Parque Industrial La Joya, Cuautitlan
Izcalli, Estado de México, C.P. 54730, México. Tel. (55)1500-4500
La presente garantía cubre este producto por 3 años contra cualquier defecto de fabricación en sus materiales y mano de obra, bajo las siguientes condiciones:
1. Todos los productos a que se refiere esta garantía, ampara su cambio físico, sin ningún cargo para
el consumidor.
2. El comercializador no tiene talleres de servicio, debido a que los productos que se garantizan no
cuentan con reparaciones, ni refacciones, ya que su garantía es de cambio físico.
3. La garantía cubre exclusivamente aquellas partes, equipos o sub-ensambles que hayan sido instaladas
defábrica y no incluye en ningún caso el equipo adicional o cualesquiera que hayan sido adicionados
al mismo por el usuario o distribuidor.
Para hacer efectiva esta garantía bastara con presentar el producto al distribuidor en el domicilio donde fue adquirido o en el domicilio de IC Intracom México, S.A. de C.V., junto con los accesorios contenidos en su empaque, acompañado de su póliza debidamente llenada y sellada por la casa vendedora
(indispensable el sello y fecha de compra) donde lo adquirió, o bien, la factura o ticket de compra original donde se mencione claramente el modelo, numero de serie (cuando aplique) y fecha de adquisición. Esta garantia no es valida en los siguientes casos: Si el producto se hubiese utilizado en condiciones distintas a las normales; si el producto no ha sido operado conforme a los instructivos de uso; ó si el producto ha sido alterado o tratado de ser reparado por el consumidor ó terceras personas.
39
FEDERAL COMMUNICATIONS COMMISSION
REGULATORY STATEMENT
FCC Class B
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of Federal Communications
Commission (FCC) Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment to an outlet on a circuit different from the receiver.
• Consult the dealer or an experienced radio/TV technician for help.
R&TTE
ENGLISH
This device complies with the requirements of the R&TTE Directive 1999/5/EC.
dEutSCH
Dieses Gerät enspricht der Direktive R&TTE Direktive 1999/5/EC.
ESPAñOL
Este dispositivo cumple con los requerimientos de la Directiva R&TTE 1999/5/EC.
FRANçAIS
Cet appareil satisfait aux exigences de la directive R&TTE 1999/5/CE.
POLSkI
Urządzenie spełnia wymagania dyrektywy R&TTE 1999/5/EC.
ItALIANO
Questo dispositivo è conforme alla Direttiva 1999/5/EC R&TTE.
40
intEllinEt nEtWoRK solutions ™ offers a complete line of active and passive networking products.
Ask your local computer dealer for more information or visit www.intellinet-network.com.
All products mentioned are trademarks or registered trademarks of their respective owners. intEllinEt nEtWoRK solutions ™ bietet ein vollständiges Sortiment aktiver und passiver
Netzwerkkomponenten. Für weitere Informationen wenden Sie sich bitte an Ihren Händler oder nutzen Sie die Webseite www.intellinet-network.com.
Alle erwähnten Produkte sind registrierte Marken und Eigentum Ihrer jeweiligen Besitzer.
intEllinEt nEtWoRK solutions ™ ofrece una línea completa de productos de red activa y pasiva.
Pregunte a su distribuidor para obtener mayor informacion o visite:
www.intellinet-network.com.
Todos los productos mencionados son marcas comerciales o marcas registradas de sus respectivos propietarios.
intEllinEt nEtWoRK solutions ™ offre un assortiment complet de produits de réseau actifs et
passifs. Pour plus d’informations veuillez contacter votre revendeur ou utiliser la page d’accueil
www.intellinet-network.com.
Tous les produits mentionnés sont des marques commerciales ou des marques déposées de leurs propriétaires respectifs.
intEllinEt nEtWoRK solutions ™ to kompletna linia aktywnych oraz pasywnych komponentów sieciowych. Poproś lokalnego dealera o więcej informacji lub odwiedź stronę
www.intellinet-network.com.
Wszystkie nazwy handlowe i towarów są nazwami i znakami towarowymi zastrzeżonymi odpowiednich firm odnośnych właścicieli.
intEllinEt nEtWoRK solutions ™ offre una linea completa di prodotti di rete attivi e passivi.
Chiedi maggiori informazioni al tuo rivenditore di computer o visita il sito
www.intellinet-network.com.
Tutti i prodotti sopracitati sono marchi di fabbrica o marchi registrati depositati dai proprietari.
Copyright © INTELLINET NETWORK SOLUTIONS
Advertisement
Key features
- Black, Grey
- 150 Mbit/s
- Fast Ethernet
- Ethernet WAN
- Ethernet LAN (RJ-45) ports: 1