CAL. VD50 1/10 SECOND RETROGRADE

CAL. VD50 1/10 SECOND RETROGRADE
CAL. VD50
1/10 SECOND RETROGRADE CHRONOGRAPH
l Hour, minute and second hands
l Date displayed in numerals
STOPWATCH
l Measures up to 60 minutes in 1/10 second increments.
ENGLISH
TIME/CALENDAR
SCREW DOWN CROWN
DISPLAY AND CROWN/BUTTONS
[for models with screw down crown]
STOPWATCH
1/10-second hand
Minute hand
A
STOPWATCH
minute hand
a
2 Crown can be pulled out.
b
Locking the crown
c
CROWN
Date
Second hand
1 Turn Crown counterclockwise until you no
longer feel the threads turning.
B
1 Push Crown back in to normal position.
English
English
Hour hand
Unlocking the crown
2 Turn Crown clockwise while pressing it
lightly until tight.
STOPWATCH
second hand
2
a: Normal position
b: First click
c: Second click
3
ADJUSTING THE STOPWATCH HAND POSITION
TIME/CALENDAR SETTING
lBefore setting the time, be sure to check that the STOPWATCH hands are in
the “0” position when the stopwatch is reset (for resetting the stopwatch, see
"STOPWATCH").
STOPWATCH
1/10-second
hand
CROWN
s
A
A
s
B
4
STOPWATCH
second hand
Press repeatedly to reset the
STOPWATCH 1/10 second
hand to the “0” position.
Press repeatedly to reset the
STOPWATCH second and minute hands to the “0” position.
s
B
STOPWATCH
minute hand
Hour hand
Pull out to second click
CROWN
Push back in to normal
position.
CROWN
Date
1 Pull out to first click, and turn clockwise until the previous day’s date
appears.
2 Pull out to second click when Second hand is at the 12 o’clock position.
3 Turn clockwise until the desired date appears.
4 Turn to set Hour and Minute hands.
5 Push back in to normal position in accordance with a time signal.
English
English
*If any of the STOPWATCH hands do not return to the "0" position when the stopwatch is reset, follow the procedure below to reset the hands.
Minute hand
Second hand
5
STOPWATCH
A
STOP
A
RESTART
A
STOP
B
RESET
Movement of the STOPWATCH 1/10 second hand
English
START
A
s
English
Accumulated elapsed time measurement
s
6
B
RESET
STOP
s
STOPWATCH
second hand
A Start / Stop / Restart
A
s
STOPWATCH
minute hand
STOPWATCH
1/10-second hand
A
START
s
*If the STOPWATCH hands do not return to the "0" position when the stopwatch is
reset, follow the procedure in "ADJUSTING THE STOPWATCH HAND POSITION"
to reset the hands..
Standard measurement
s
lThe stopwatch can measure up to 60 minutes in 1/10 second increments.
lThe measured time is indicated by the STOPWATCH hands that move independently of the center hands.
l Before using the stopwatch, be sure to check that the crown is set at the normal position and that the STOPWATCH hands are reset to the “0” position.
lAfter the measurement exceeds 1 minute, the STOPWATCH 1/10 second
hand stays at the "0" position while the stopwatch is counting.
lWhen the measurement is stopped, the hand moves to indicate the elapsed
1/10 seconds.
B Reset
7
NOTES ON OPERATING THE WATCH
ADJUSTING THE STOPWATCH HAND POSITION
lThe STOPWATCH minute hand moves correspondingly with the STOPWATCH
second hand.
8
TIME/CALENDAR SETTING
lIt is necessary to adjust the date on the first day after a 30-day month and February.
lDo not set the date between 9:00 p.m. and 1:00 a.m., as the date may not change
properly. If it is necessary to set the date during that period of time, first change the
time to any time outside of this period, set the date, and then reset to the correct
time.
Do
not press any button when the crown is at the second click position, as this will
l
move the STOPWATCH hands.
lWhen setting the hour hand, be sure to check that AM/PM is correctly set. The
watch is designed so that the date changes once in 24 hours.
*Turn the hands past the12 o’clock marker to determine whether the watch is set
for the A.M. or P.M. period. If the date changes,the time is set for the A.M.
period. If not, the time is set for the P.M. period.
time and then turn it back to the exact minute.
STOPWATCH
lRestart and stop of the stopwatch can be repeated by pressing button A.
BATTERY CHANGE
2
Years
Battery life : Approx. 2 years
Battery
: SEIKO SR920SW
English
English
lThe STOPWATCH hands move quickly if the respective buttons are kept pressed.
lWhen setting the minute hand, first advance it 4 to 5 minutes ahead of the desired
lIf the stopwatch is used for more than 2 hours a day, the battery life may be less
than the specified period.
l As the battery is inserted at the factory to check the function and performance of
the watch, its actual life once in your possession may be less than the specified
period.
lWhen the battery expires, be sure to replace it as soon as possible to prevent any
malfunction.
9
lWe recommend that you contact an AUTHORIZED PULSAR DEALER for battery
replacement.
lNecessary procedure after battery change
After the battery is replaced with a new one, or in case any of the hands should move
improperly, follow the procedure below to reset the STOPWATCH hands to “0” position.
CROWN
and
B
s
B
CROWN
Press and hold simultaneously
for 2 seconds or longer.
*The STOPWATCH second hand
turns counterclockwise, and then
returns to where it was.
Press repeatedly to set the
STOPWATCH 1/10 second
hand to the “0” position.
Press repeatedly to set the
STOPWATCH second and minute
hands to the “0” position.
Turn to set the time.
s
* The STOPWATCH minute
hand moves correspondingly with the STOPWATCH
second hand.
* The STOPWATCH hands
move quickly if the re spective buttons are kept
pressed.
s
B
A
s
English
A
English
10
A
When the battery nears its end, the second hand moves at two-second intervals
instead of normal one-second intervals. In that case, have the battery replaced with
a new one as soon as possible.
* The watch remains accurate while the second hand is moving at two-second
intervals.
s
lBattery life indicator
Pull out to second click.
CROWN
Push back in to normal position.
11
WARNING
l Do not remove the battery from the watch.
lIf it is necessary to take out the battery, keep it out of the reach of
children. If a child swallows it, consult a doctor immediately.
lNever short-circuit, tamper with or heat the battery, and never ex-
CAUTION
l The battery is not rechargeable. Never attempt to recharge it, as this
may cause battery leakage or damage to the battery.
12
WATER RESISTANCE
l Water resistance (5 bar)*
If “WATER RESISTANT 5 BAR”
l Non-water resistant
is inscribed on the case back,
If “WATER RESISTANT” is not
your watch is designed and
inscribed on the case back, your
manu-factured to withstand up to
watch is not water resistant, and
care should be taken not to get 5 bar and is suitable for swimming, yachting and
it wet as water may damage the movement. If taking a shower.
the watch becomes wet, we suggest that you l Water resistance (10 bar/15 bar/20
bar)*
have it checked by an AUTHORIZED PULSAR
If “WATER RESISTANT 10 BAR”,
DEALER or SERVICE CENTER.
“WATER RESISTANT 15 BAR” or
l Water resistance (3 bar)
“WATER RESISTANT 20 BAR” is
If “WATER RESISTANT” is inscribed
inscribed on the case back, your
on the case back, your watch is watch is designed and manufactured to withstand
designed and manufactured to up to 10 bar/15 bar/20 bar and is suitable for taking
withstand up to 3 bar, such as acci­ a bath, shallow diving, but not for scuba diving.
dental contact with splashes of water or rain, but it We recommend that you wear a PULSAR Diver’s
is not designed for swimming or diving.
watch for scuba diving.
13
English
English
pose it to fire. The battery may burst, become very hot or catch fire.
TO PRESERVE THE QUALITY OF YOUR WATCH
NOTE:
Pressure in bar is a test pressure and should not be considered as
corresponding to actual diving depth since swimming movement
tends to increase the pressure at a given depth. Care should also be
taken on diving into water.
TEMPERATURES
Your watch works with
stable accuracy within a
temperature range of 5°
C and 35° C (41° F and
95° F).
Temperatures over 60° C (140° F)
14 may cause battery leakage or short-
en the battery life. Do not leave
your watch in very low temperatures
below –10° C (+14° F) for a long
time since the cold may cause a
slight time loss or gain.
However, the above conditions will
be corrected when the watch returns to normal temperature.
MAGNETISM
Your watch will be adversely affected by strong
magnetism. Keep it away
from close contact with
magnetic objects.
SHOCKS & VIBRATION
CARE OF CASE AND BRACELET
To prevent possible rusting of
the case and bracelet caused
by dust, moisture and perspiration, wipe them periodically
with a soft dry cloth.
PERIODIC CHECK
It is recommended that the
Light activities will not
watch be checked once
affect your watch, but be
every 2 to 3 years. Have
careful not to drop your
your watch checked by an
watch or hit it against
AU T H O R I Z E D P U L S A R
hard surfaces, as this
DEALER
or
SER­
V ICE CENTER to
may cause damage.
ensure that the case, crown, buttons,
gasket and crystal seal remain intact.
CHEMICALS
Be careful not to expose
the watch to solvents,
mercury, cosmetic spray,
detergents, adhesives or
paints. Otherwise, the
case, bracelet, etc. may become
discolored, deteriorated or damaged.
English
English
* Before using the water resistance 5, 10, 15 or 20 bar watch in water, be sure the
crown is pushed in completely.
Do not operate the crown when the watch is wet or in water. If used in sea water,
rinse the watch in fresh water and dry it completely.
* When taking a shower with the water resistance 5 bar watch, or taking a bath with
the water resistance 10, 15 or 20 bar watch, be sure to observe the following:
• Do not operate the crown when the watch is wet with soapy water or shampoo.
• If the watch is left in warm water, a slight time loss or gain may be caused. This
condition, however, will be corrected when the watch returns to normal temperature.
PRECAUTION REGARDING
CASE BACK PROTECTIVE FILM
If your watch has a protective film and/or a sticker
on the case back, be sure
to peel them off before using your watch.
15
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement