Asrock 775V88+ motherboard Datasheet

775V88/775V88+
User Manual
Version 1.0
Published December 2004
Copyright©2004 ASRock INC. All rights reserved.
1
Copyright Notice:
No part of this manual may be reproduced, transcribed, transmitted, or translated in
any language, in any form or by any means, except duplication of documentation by
the purchaser for backup purpose, without written consent of ASRock Inc.
Products and corporate names appearing in this manual may or may not be registered trademarks or copyrights of their respective companies, and are used only for
identification or explanation and to the owners’ benefit, without intent to infringe.
Disclaimer:
Specifications and information contained in this manual are furnished for informational use only and subject to change without notice, and should not be constructed
as a commitment by ASRock. ASRock assumes no responsibility for any errors or
omissions that may appear in this manual.
With respect to the contents of this manual, ASRock does not provide warranty of
any kind, either expressed or implied, including but not limited to the implied warranties or conditions of merchantability or fitness for a particular purpose.
In no event shall ASRock, its directors, officers, employees, or agents be liable for
any indirect, special, incidental, or consequential damages (including damages for
loss of profits, loss of business, loss of data, interruption of business and the like),
even if ASRock has been advised of the possibility of such damages arising from any
defect or error in the manual or product.
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation.
ASRock Website: http://www.asrock.com
2
Contents
1. Introduction .................................................. 5
1.1
1.2
1.3
1.4
Package Contents ..........................................................
Specifications ................................................................
Motherboard Layout ......................................................
ASRock I/O PlusTM .................................................................................................
5
6
8
9
2. Installation .................................................... 10
Pre-installation Precautions ...................................................
2.1 CPU Installation ..............................................................
2.2 Installation of CPU Fan and Heatsink ............................
2.3 Installation of Memory Modules (DIMM) .........................
2.4 Expansion Slots (PCI and AGP Slots) ...........................
2.5 Jumpers Setup ..............................................................
2.6 Onboard Headers and Connectors ..............................
2.7 Serial ATA (SATA) Hard Disks Installation .....................
2.8 Hot Plug and Hot Swap Functions for SATA HDDs .......
2.9 Making An SATA Driver Diskette ....................................
10
11
13
14
16
17
18
21
21
22
3. BIOS SETUP UTILITY ......................................... 23
3.1 Introduction ....................................................................
3.1.1 BIOS Menu Bar ....................................................
3.1.2 Navigation Keys ...................................................
3.2 Main Screen ...................................................................
3.3 Advanced Screen .........................................................
3.3.1 CPU Configuration ................................................
3.3.2 Chipset Configuration ..........................................
3.3.3 ACPI Configuration ...............................................
3.3.4 IDE Configuration .................................................
3.3.5 PCIPnP Configuration ...........................................
3.3.6 Floppy Configuration ...........................................
3.3.7 Super IO Configuration ........................................
3.3.8 USB Configuration ...............................................
3.4 Hardware Health Event Monitoring Screen ..................
3.5 Boot Screen ...................................................................
3.5.1 Boot Settings Configuration ..................................
3.5.2 Boot Device Priority ...............................................
3.6 Security Screen ............................................................
3.7 Exit Screen ....................................................................
3
23
23
24
24
25
25
26
28
29
31
31
32
33
34
34
35
35
36
37
4. Software Support .......................................... 38
4.1 Install Operating System ...............................................
4.2 Support CD Information .................................................
4.2.1 Running Support CD ............................................
4.2.2 Drivers Menu ........................................................
4.2.3 Utilities Menu ........................................................
4.2.4 “LGA 775 CPU Installation Live Demo” Program ..
4.2.5 Contact Information ..............................................
4
38
38
38
38
38
38
38
1. Introduction
Thank you for purchasing ASRock 775V88/775V88+ motherboard, a reliable
motherboard produced under ASRock’s consistently stringent quality control. It delivers excellent performance with robust design conforming to ASRock’s commitment to quality and endurance.
In this manual, chapter 1 and 2 contain introduction of the motherboard and step-bystep guide to the hardware installation. Chapter 3 and 4 contain the configuration
guide to BIOS setup and information of the Support CD.
Because the motherboard specifications and the BIOS software might be
updated, the content of this manual will be subject to change without
notice. In case any modifications of this manual occur, the updated
version will be available on ASRock website without further notice. You
may find the latest memory and CPU support lists on ASRock website as
well. ASRock website http://www.asrock.com
1.1 Package Contents
ASRock 775V88/775V88+ Motherboard
(ATX Form Factor: 12.0-in x 9.2-in, 30.5 cm x 23.4 cm)
ASRock 775V88/775V88+ Quick Installation Guide
ASRock 775V88/775V88+ Support CD
(including LGA 775 CPU Installation Live Demo)
One 80-conductor Ultra ATA 66/100/133 IDE Ribbon Cable
One Ribbon Cable for a 3.5-in Floppy Drive
One Serial ATA (SATA) Cable
One Serial ATA (SATA) HDD Power Cable(Optional)
One ASRock I/O PlusTM Shield
5
1.2 Specifications
Platform:
CPU:
ATX Form Factor: 12.0-in x 9.2-in, 30.5 cm x 23.4 cm
775-Pin Socket
Supporting Intel® Pentium® 4 / Celeron® processor (in 775-land
LGA package)
North Bridge:
VIA PT880, FSB @ 800/533 MHz,
with Intel® Hyper-Threading Technology ready
(see CAUTION 1)
South Bridge:
VIA VT8237, supports USB 2.0, ATA 133, SATA 1.5Gb/s
Memory:
4 DDR DIMM Slots: DDR1, DDR2, DDR3, and DDR4
2 DDR DIMM Slots Supports PC3200 (DDR400), Max.1GB,
4 DDR DIMM Slots Supports PC2700 (DDR333) /
PC2100 (DDR266), Max. 3.5GB,
Dual Channel Memory Technology support (see CAUTION 2)
IDE:
IDE1: ATA 133 / Ultra DMA Mode 6
IDE2: ATA 133 / Ultra DMA Mode 6
Supports up to 4 IDE devices
Serial ATA:
2 SATA connectors
Support up to 1.5Gb/s data transfer rate
Floppy Port:
Supports up to 2 floppy disk drives
Audio:
5.1 channels AC’97 Audio
LAN:
Speed: 802.3u (10/100 Ethernet), supports Wake-On-LAN
Hardware Monitor: CPU temperature sensing
Chassis temperature sensing
CPU overheat shutdown to protect CPU life
(ASRock U-COP)(see CAUTION 3)
CPU fan tachometer
Chassis fan tachometer
Voltage monitoring: +12V, +5V, +3.3V, Vcore
PCI slots:
5 slots with PCI Specification 2.2
AGP slot:
1 AGP slot, supports 1.5V, 8X/4X AGP card (see CAUTION 4)
USB 2.0:
8 USB 2.0 ports:
include 6 ready-to-use USB 2.0 ports on the rear panel,
plus one on-board header supporting 2 extra USB 2.0 ports
(see CAUTION 5)
Chipsets:
6
ASRock I/O PlusTM: 1 PS/2 mouse port, 1 PS/2 keyboard port,
1 serial port: COM1,
1 parallel port: ECP/EPP support,
6 ready-to-use USB 2.0 ports,
1 RJ 45 port,
Audio Jack: Line In / Line Out / Microphone
BIOS:
AMI BIOS
Supports “Plug and Play”
ACPI 1.1 compliance wake up events
Supports jumperfree
SMBIOS 2.3.1 support
CPU frequency stepless control
(only for advanced users’ reference, see CAUTION 6)
OS:
Microsoft® Windows® 98SE / ME / 2000 / XP compliant
CAUTION!
1.
2.
About the setting of “Hyper Threading Technology”, please check page 26.
This motherboard supports Dual Channel Memory Technology. Before you
implement Dual Channel Memory Technology, make sure to read the
installation guide of memory modules on page 14 for proper installation.
3.
While CPU overheat is detected, the system will automatically shutdown.
Before you resume the system, please check if the CPU fan on the
motherboard functions properly and unplug the power cord, then plug it
back again. To improve heat dissipation, remember to spray thermal
4.
grease between the CPU and the heatsink when you install the PC system.
Do NOT use a 3.3V AGP card on the AGP slot of this motherboard!
5.
It may cause permanent damage!
Power Management for USB 2.0 works fine under Microsoft® Windows® XP
SP1 / 2000 SP4. It may not work properly under Microsoft® Windows® 98 /
ME.
6.
Although this motherboard offers stepless control, it is not recommended
to perform over-clocking. Frequencies other than the recommended CPU
bus frequencies may cause the instability of the system or damage the
CPU.
7
1.3 Motherboard Layout
1 2
3 4
5
6
23.4cm (9.2 in)
1
PS2_USB_PWR1
PS2
Mouse
ATX12V1
30.5cm (12.0in)
IDE2
DDR3 (64/72 bit, 184-pin module)
7
Prescott 800
Dual Channel
P V
Ch T8 IA
ip 80
se
t
2Mb
BIOS
27
8
IR1
1
Super
I/O
1.5V_AGP1
IDE1
26
ATXPWR1
USB 2.0
T: USB4
B: USB5
Top:
Line In
Center:
Line Out
Bottom:
Mic In
28
CPU_FAN1
29
DDR4 (64/72 bit, 184-pin module)
USB 2.0
T: USB2
B: USB3
USB 2.0
T: USB0 Top:
B: USB1 RJ-45
DDR2 (64/72 bit, 184-pin module)
COM1
DDR1 (64/72 bit, 184-pin module)
PARALLEL PORT
Ps2
Keyboard
9
LAN
PHY
ATA133
5.1 CH
24
CD1
AUX1
23
SATA
USB2.0
11
12
CMOS
Battery
PCI 4
Audio
CODEC
10
AGP 8X
PCI 3
GAME1
SATA2
VIA
VT8237
PCI 2
25
SATA1
PCI 1
13
FSB800
DDR400
AUDIO1
CLRCMOS1
22
21
PCI 5
775V88+
USB67
JR1
6
7
8
9
10
11
12
13
14
SPEAKER1
1
HDLED RESET
PANEL 1
CHA_FAN1
FLOPPY1
JL1
20
1
2
3
4
5
14
PLED PWRBTN
1
1
1
18
19
PS2_USB_PWR1 Jumper
ATX 12V Connector (ATX12V1)
775-Pin CPU Socket
North Bridge Controller
2 x 184-pin DDR DIMM Slots
(Dual Channel A: DDR1, DDR3; Blue)
2 x 184-pin DDR DIMM Slots
(Dual Channel B: DDR2, DDR4; Black)
Secondary IDE Connector (IDE2, Black)
Primary IDE Connector (IDE1, Blue)
AGP Slot (1.5V_AGP1)
Secondary Serial ATA Connector (SATA2)
Primary Serial ATA Connector (SATA1)
South Bridge Controller
CMOS Battery
Chasis fan connector (CHA_FAN)
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
8
17 16
15
System Panel Header (PANEL1)
Chasis Speaker Header (SPEAKER 1)
Clear CMOS Jumper (CLRCMOS1)
USB 2.0 Header (USB67, Blue)
Floppy Connector (FLOPPY1)
Internal Audio Connector: CD1 (Black)
JR1 Jumper / JL1 Jumper
Front Panel Audio Header (AUDIO1)
Internal audio connector: AUX1 (White)
Game Connector (GAME1)
PCI Slots (PCI 1-5)
Infrared Module Header (IR1)
BIOS chip
ATX Power Connector (ATXPWR1)
CPU Fan Connector (CPU_FAN1)
1.4 ASRock I/O Plus TM
1
2
3
4
5
11
1
2
3
4
5
6
10
9
8
Parallel Port
RJ-45 Port
Line In (Light Blue)
Line Out (Lime)
Microphone (Pink)
2 x Shared USB 2.0 Ports (USB4, USB5)
7
8
9
10
11
9
7
6
2 x USB 2.0 Ports (USB0, USB1)
2 x USB 2.0 Ports (USB2, USB3)
Serial Port: COM1
PS/2 Keyboard Port (Purple)
PS/2 Mouse Port (Green)
2. Installation
775V88/775V88+ is an ATX form factor (12.0-in x 9.2-in, 30.5 cm x 23.4 cm)
motherboard. Before you install the motherboard, study the configuration of your
chassis to ensure that the motherboard fits into it.
Pre-installation Precautions
Take note of the following precautions before you install motherboard components or change any motherboard settings.
1. Unplug the power cord from the wall socket before touching any
component.
2. To avoid damaging the motherboard components due to static electricity,
NEVER place your motherboard directly on the carpet or the like. Also
remember to use a grounded wrist strap or touch a safety grounded
object before you handle components.
3. Hold components by the edges and do not touch the ICs.
4. Whenever you uninstall any component, place it on a grounded antistatic pad or in the bag that comes with the component.
Before you install or remove any component, ensure that the power is
switched off or the power cord is detached from the power supply.
Failure to do so may cause severe damage to the motherboard,
peripherals, and/or components.
10
2.1 775-LAND CPU Installation
For the installation of Intel 775-LAND CPU,
please follow the steps below.
775-Pin Socket Overview
Before you insert the 775-LAND CPU into the socket, please check if
the CPU surface is unclean or if there is any bent pin on the socket.
Do not force to insert the CPU into the socket if above situation is
found. Otherwise, the CPU will be seriously damaged.
Step 1. Open the socket:
Step 1-1. Disengaging the lever by depressing
down and out on the hook to clear
retention tab.
Step 1-2. Rotate the load lever to fully open position at approximately 135 degrees.
Step 1-3. Rotate the load plate to fully open position at approximately 100 degrees.
black line
black line
Step 2. Insert the 775-LAND CPU:
Step 2-1. Hold the CPU by the edges where are
marked with black lines.
Step 2-2. Orient the CPU with IHS (Integrated
Heat Sink) up. Locate Pin1 and the two
orientation key notches.
Pin1
orientation
key notch
Pin1
alignment key
orientation
key notch
alignment key
775-Pin Socket
775-LAND CPU
11
For proper inserting, please ensure to match the two orientation key
notches of the CPU with the two alignment keys of the socket.
Step 2-3. Carefully place the CPU into the socket
by using a purely vertical motion.
Step 2-4. Verify that the CPU is within the socket
and properly mated to the orient keys.
Step 3. Remove PnP Cap (Pick and Place Cap):
Use your left hand index finger and thumb to
support the load plate edge, engage PnP cap
with right hand thumb and peel the cap from the
socket while pressing on center of PnP cap to
assist in removal.
It is recommended to use the cap tab to handle and avoid kicking off
the PnP cap.
Step 4. Close the socket:
Step 4-1. Rotate the load plate onto the IHS.
Step 4-2. While pressing down lightly on load
plate, engage the load lever.
Step 4-3. Secure load lever with load plate tab
under retention tab of load lever.
12
2.2
Installation of CPU Fan and Heatsink
This motherboard is equipped with 775-Pin socket that supports Intel 775-LAND CPU.
Please adopt the type of heatsink and cooling fan compliant with Intel 775-LAND CPU
to dissipate heat. Before you installed the heatsink, you need to spray thermal
interface material between the CPU and the heatsink to improve heat dissipation.
Ensure that the CPU and the heatsink are securely fastened and in good contact with
each other. Then connect the CPU fan to the CPU_FAN connector (CPU_FAN1, see
page 8, No. 29).
For proper installation, please kindly refer to the instruction manuals of
your CPU fan and heatsink.
Below is an example to illustrate the installation of the heatsink for 775-LAND CPU.
Step 1. Apply thermal interface material onto center
of IHS on the socket surface.
Step 2.
Step 3.
Step 4.
Place the heatsink onto the socket. Ensure
fan cables are oriented on side closest to the
CPU fan connector on the motherboard
(CPU_FAN1, see page 8, No. 29).
Align fasteners with the motherboard
throughholes.
Rotate the fastener clockwise, then press
down on fastener caps with thumb to install
and lock. Repeat with remaining fasteners.
If you press down the fasteners without rotating them clockwise,
the heatsink cannot be secured on the motherboard.
Step 5.
Connect fan header with the CPU fan
connector on the motherboard.
Step 6.
Secure excess cable with tie-wrap to ensure
cable does not interfere with fan operation or
contact other components.
13
2.3 Installation of Memory Modules (DIMM)
775V88/775V88+ motherboard provides four 184-pin DDR (Double Data Rate)
DIMM slots, and supports Dual Channel Memory Technology. For dual channel
configuration, you always need to install identical (the same brand, speed,
size and chip-type) DDR DIMM pair in the slots of the same color. In other words,
you have to install identical DDR DIMM pair in Dual Channel A (DDR1 and
DDR3; Blue slots; see p.8 No.5) or identical DDR DIMM pair in Dual Channel B
(DDR2 and DDR4; Black slots; see p.8 No.6), so that Dual Channel Memory
Technology can be activated. This motherboard also allows you to install four
DDR DIMMs for dual channel configuration, and please install identical DDR
DIMMs in all four slots. You may refer to the Dual Channel Memory Configuration
Table below.
Dual Channel Memory Configurations
DDR1
(Blue Slot)
Populated
Populated
(1)
(2)
(3)*
DDR2
(Black Slot)
Populated
Populated
DDR3
(Blue Slot)
Populated
Populated
DDR4
(Black Slot)
Populated
Populated
* For the configuration (3), please install identical DDR DIMMs in all four slots.
1.
If you want to install two memory modules, for optimal compatibility
and reliability, it is recommended to install them in the slots of the
same color. In other words, install them either in the set of blue slots
2.
(DDR1 and DDR3), or in the set of black slots (DDR2 and DDR4).
If only one memory module or three memory modules are installed
in the DDR DIMM slots on this motherboard, it is unable to activate
the Dual Channel Memory Technology.
3.
If a pair of memory modules is NOT installed in the same Dual
Channel, for example, installing a pair of memory modules in DDR1
and DDR2, it is unable to activate the Dual Channel Memory Technology .
14
Installing a DIMM
Please make sure to disconnect power supply before adding or
removing DIMMs or the system components.
Step 1.
Step 2.
Unlock a DIMM slot by pressing the retaining clips outward.
Align a DIMM on the slot such that the notch on the DIMM matches the break
on the slot.
notch
break
notch
break
The DIMM only fits in one correct orientation. It will cause permanent
damage to the motherboard and the DIMM if you force the DIMM into the
slot at incorrect orientation.
Step 3.
Firmly insert the DIMM into the slot until the retaining clips at both ends fully
snap back in place and the DIMM is properly seated.
15
2.4 Expansion Slots (PCI and AGP Slots)
There are 5 PCI slots and 1 AGP slot on 775V88/775V88+ motherboard.
PCI slots: PCI slots are used to install expansion cards that have the 32-bit PCI
interface.
AGP slot: The AGP slot is used to install a graphics card. The ASRock AGP slot has
a special design of clasp that can securely fasten the inserted graphics
card.
Please do NOT use a 3.3V AGP card on the AGP slot of this motherboard!
It may cause permanent damage! For the voltage information of your
AGP card, please check with the AGP card vendors.
Installing an expansion card
Step 1.
Step 2.
Step 3.
Step 4.
Step 5.
Step 6.
Before installing the expansion card, please make sure that the power
supply is switched off or the power cord is unplugged. Please read the
documentation of the expansion card and make necessary hardware
settings for the card before you start the installation.
Remove the system unit cover (if your motherboard is already installed in a
chassis).
Remove the bracket facing the slot that you intend to use. Keep the screws
for later use.
Align the card connector with the slot and press firmly until the card is
completely seated on the slot.
Fasten the card to the chassis with screws.
Replace the system cover.
16
2.5 Jumpers Setup
The illustration shows how jumpers are
setup. When the jumper cap is placed on
pins, the jumper is “Short”. If no jumper cap
is placed on pins, the jumper is “Open”. The
illustration shows a 3-pin jumper whose pin1
and pin2 are “Short” when jumper cap is
placed on these 2 pins.
Jumper
PS2_USB_PWR1
Short
Open
Setting
2_3
1_2
Short pin2, pin3 to enable
+5VSB (standby) for PS/2
or USB wake up events.
Note: To select +5VSB, it requires 2 Amp and higher standby current provided
by power supply.
(see p.8, No. 1)
+5VSB
+5V
JR1(see p.8, No. 21)
JL1(see p.8, No. 21)
JR1
JL1
Note: If the jumpers JL1 and JR1 are short, both the front panel and the rear panel
audio connectors can work.
Clear CMOS
(CLRCMOS1, 2-pin jumper)
(see p.8, No. 17)
2-pin jumper
Note: CLRCMOS1 allows you to clear the data in CMOS. The data in CMOS includes
system setup information such as system password, date, time, and system
setup parameters. To clear and reset the system parameters to default setup,
please turn off the computer and unplug the power cord, then use a jumper
cap to short the pins on CLRCMOS1 for 3 seconds. Please remember to
remove the jumper cap after clearing the CMOS. If you need to clear the CMOS
when you just finish updating the BIOS, you must boot up the system first, and
then shut it down before you do the clear-CMOS action.
17
2.6 Onboard Headers and Connectors
Onboard headers and connectors are NOT jumpers. Do NOT place jumper
caps over these headers and connectors. Placing jumper caps over the
headers and connectors will cause permanent damage of the motherboard!
FDD Connector
(33-pin FLOPPY1)
Pin1
(see p.8, No. 19)
FLOPPY1
the red-striped side to Pin1
Note: Make sure the red-striped side of the cable is plugged into Pin1 side of the
connector.
Primary IDE Connector (Blue)
Secondary IDE Connector (Black)
(39-pin IDE1, see p.8, No. 8)
(39-pin IDE2, see p.8, No. 7)
PIN1
IDE1
PIN1
IDE2
connect the black end
to the IDE devices
connect the blue end
to the motherboard
80-conductor ATA 66/100/133 cable
Note: If you use only one IDE device on this motherboard, please set the IDE
device as “Master”. Please refer to the instruction of your IDE device vendor
for the details. Besides, to optimize compatibility and performance, please
connect your hard disk drive to the primary IDE connector (IDE1, blue) and
CD-ROM to the secondary IDE connector (IDE2, black).
Serial ATA Connectors
SATA2
(SATA1: see p.8, No. 11)
(SATA2: see p.8, No. 10)
SATA1
Serial ATA (SATA)
Data Cable
These two Serial ATA (SATA)
connectors support SATA data
cables for internal storage
devices. The current SATA
interface allows up to 1.5 Gb/s
data transfer rate.
Either end of the SATA data
cable can be connected to the
SATA hard disk or the SATA
connector on the motherboard.
18
Serial ATA (SATA)
Power Cable
Please connect the black end of
SATA power cable to the power
(Optional)
connector on the drive. Then
connect the white end of SATA
power cable to the power
connector of the power supply.
connect to the SATA HDD
power connector
connect to the
power supply
USB_PWR
P-7
P+7
GND
DUMMY
USB 2.0 Header
(9-pin USB67)
(see p.8, No. 18)
1
GND
P+6
P-6
USB_PWR
Infrared Module Header
IRTX
+5V
DUMMY
(5-pin IR1)
1
(see p.8, No. 26)
ASRock I/O PlusTM provides you
6 ready-to-use USB 2.0 ports on
the rear panel. If the rear USB
ports are not sufficient, this
USB 2.0 header is available to
support 2 extra USB 2.0 ports.
This header supports an optional
wireless transmitting and
receiving infrared module.
GND
IRRX
Internal Audio Connectors
(4-pin CD1, 4-pin AUX1)
CD-R
GND
GND
CD-L
AUX-R
GND
GND
AUX-L
(CD1: see p.8, No. 20)
AUX1
(AUX1: see p.8, No. 23)
GND
+5VA
BACKOUT-R
BACKOUT-L
Front Panel Audio Header
(9-pin AUDIO1)
(see p.8, No. 22)
CD1
1
AUD-OUT-L
GND
AUD-OUT-R
MIC-POWER
MIC
PLED+
PLEDPWRBTN#
GND
System Panel Header
(9-pin PANEL1)
(see p.8, No. 15)
1
These connectors allow you
to receive stereo audio input
from sound sources such as
a CD-ROM, DVD-ROM, TV
tuner card, or MPEG card.
This is an interface for the front
panel audio cable that allows
convenient connection and
control of audio devices.
This header accommodates
several system front panel
functions.
DUMMY
RESET#
GND
HDLEDHDLED+
Chassis Speaker Header
(4-pin SPEAKER 1)
(see p.8, No. 16)
1
SPEAKER
DUMMY
DUMMY
+5V
19
Please connect the chassis
speaker to this header.
Chassis Fan Connector
(3-pin CHA_FAN1)
GND
+12V
CHA_FAN_SPEED
(see p.8, No. 14)
CPU Fan Connector
Please connect the chassis fan
cable to this connector and
match the black wire to the
ground pin.
You may connect either a 3-pin
or a 4-pin CPU fan cable to this
connector, then match the black
wire to the ground pin.
(4-pin CPU_FAN1)
(see p.8, No. 29)
+5V
JBB1
JBX
MIDI_OUT
JBY
JBB2
MIDI_IN
Game Connector
(15-pin GAME1)
(see p.8, No. 24)
Connect a Game cable to this
connector if the Game port
bracket is installed.
1
+5V
JAB2
JAY
GND
GND
JAX
JAB1
+5V
ATX Power Connector
Please connect an ATX power
supply to this connector.
(20-pin ATXPWR1)
(see p.8, No. 28)
ATX 12V Connector
Please note that it is necessary
to connect a power supply with
ATX 12V plug to this connector
so that it can provides sufficient
power. Failing to do so will cause
the failure to power up.
(4-pin ATX12V1)
(see p.8, No. 2)
20
2.7 Serial ATA (SATA) Hard Disks Installation
This motherboard adopts VIA VT8237 southbridge chipset that supports Serial
ATA (SATA) hard disks and RAID functions. You may install SATA hard disks on
this motherboard for internal storage devices. This section will guide you to install
the SATA hard disks.
STEP 1: Install the SATA hard disks into the drive bays of your chassis.
STEP 2: Connect the SATA power cable to the SATA hard disk.
STEP 3: Connect one end of the SATA data cable to the motherboard’s SATA
connector.
STEP 4: Connect the other end of the SATA data cable to the SATA hard disk.
2.8 Hot Plug and Hot Swap Functions for SATA HDDs
775V88/775V88+ motherboard supports Hot Plug and Hot Swap functions
for SATA Devices.
NOTE
What is Hot Plug Function?
If the SATA HDDs are NOT set for RAID configuration, it is called “Hot
Plug” for the action to insert and remove the SATA HDDs while the system
is still power-on and in working condition.
However, please note that it cannot perform Hot Plug if the OS has been
installed into the SATA HDD.
What is Hot Swap Function?
If SATA HDDs are built as RAID1 then it is called “Hot Swap” for the action
to insert and remove the SATA HDDs while the system is still power-on
and in working condition.
21
2.9 Making An SATA Driver Diskette
If you want to install Windows 2000 or Windows XP on your SATA HDDs, you will
need to make an SATA driver diskette before you start the OS installation.
STEP 1: Insert the ASRock Support CD into your optical drive to boot your system.
(Do NOT insert any floppy diskette into the floppy drive at this moment!)
STEP 2: During POST at the beginning of system boot-up, press <F11> key, and
then a window for boot devices selection appears. Please select CDROM as the boot device.
STEP 3: When you see the message on the screen, “Do you want to generate
Serial ATA driver diskette [YN]?”, press <Y>.
STEP 4: Then you will see these messages,
Please insert a diskette into the floppy drive.
WARNING! Formatting the floppy diskette will
lose ALL data in it!
Start to format and copy files [YN]?
Please insert a floppy diskette into the floppy drive, and press <Y>.
STEP 5: The system will start to format the floppy diskette and copy SATA drivers
into the floppy diskette.
Once you have the SATA driver diskette ready, you may start to install Windows
2000 / Windows XP on your system directly without setting the RAID configuration on your system, or you may start to use “VT8237 SATA RAID BIOS” to set
RAID 0 / RAID 1 / JBOD configuration before you install the OS. Before you start
to configure the RAID function, you need to check the installation guide in the
Support CD for proper configuration. Please refer to the document in the Support
CD, “Guide to SATA Hard Disks Installation and RAID Configuration”, which is
located in the folder at the following path:
.. \ SATA RAID BIOS
You may also set the RAID configuration by using “VIA RAID Tool” in Windows
environment. Please refer to the document in the Support CD, “Guide to VIA RAID
Tool”, which is located in the folder at the following path:
.. \ VIA RAID Tool
22
3. BIOS SETUP UTILITY
3.1 Introduction
This section explains how to use the BIOS SETUP UTILITY to configure your system.
The Flash Memory on the motherboard stores the BIOS SETUP UTILITY. You may run
the BIOS SETUP UTILITY when you start up the computer. Please press <F2> during
the Power-On-Self-Test (POST) to enter the BIOS SETUP UTILITY, otherwise, POST
will continue with its test routines.
If you wish to enter the BIOS SETUP UTILITY after POST, restart the system by
pressing <Ctl> + <Alt> + <Delete>, or by pressing the reset button on the system
chassis. You may also restart by turning the system off and then back on.
Because the BIOS software is constantly being updated, the following
BIOS setup screens and descriptions are for reference purpose only,
and they may not exactly match what you see on your screen.
3.1.1 BIOS Menu Bar
The top of the
Main
Advanced
H/W Monitor
Boot
screen has a menu bar with the following selections:
To set up the system time/date information
To set up the advanced BIOS features
To display current hardware status
To set up the default system device to locate and load the
Operating System
Security
To set up the security features
Exit
To exit the current screen or the BIOS SETUP UTILITY
Use < > key or < > key to choose among the selections on the menu bar,
and then press <Enter> to get into the sub screen.
23
3.1.2 Navigation Keys
Please check the following table for the function description of each navigation
key.
Navigation Key(s)
/
/
+ / <Enter>
<F1>
<F9>
<F10>
<ESC>
Function Description
Moves cursor left or right to select Screens
Moves cursor up or down to select items
To change option for the selected items
To bring up the selected screen
To display the General Help Screen
To load optimal default values for all the settings
To save changes and exit the BIOS SETUP UTILITY
To jump to the Exit Screen or exit the current screen
3.2 Main Screen
When you enter the BIOS SETUP UTILITY, the Main screen will appear and display
the system overview
Advanced
Main
Main
BIOS SETUP UTILITY
H/W Monitor
Boot
System Overview
System Time
System Date
[17:00:09]
[Wed 08/02/2004]
12/22/2004]
[Tue
BIOS Version
Processor Type
Processor Speed
Cache Size
Microcode Update
:
:
:
:
:
Total Memory
: 512MB
Dual-Channel Memory Mode
: 256MB/166MHz (DDR333)
: None
: 256MB/166MHz (DDR333)
: None
DIMM
DIMM
DIMM
DIMM
1
2
3
4
775V88+
BIOSP1.00
P1.00
775V88 BIOS
Genuine
(R) (R)
CPU4 3.20GHz
Intel (R) Intel
Pentium
CPU 2.40 GHz
3200
2400 MHz
512KB
0F24/1E
Security
Use [+] or [-] to
system Time.
configure syst
+Tab
F1
F9
F10
ESC
Select Screen
Select Item
Change Field
Select Field
Genera
General Help
Load D
Defaults
Save an
and Exit
Exit
v02.54 (C) Copyright 1985-2003, American Megatrends, Inc.
System Time [Hour:Minute:Second]
Use this item to specify the system time.
System Date [Day Month/Date/Year]
Use this item to specify the system date.
24
Exit
Use [Enter], [[TAB]
[SHIFT-TAB] to
or [SHIFT-TA
select a field.
3.3 Advanced Screen
In this section, you may set the configurations for the following items: CPU
Configuration, Chipset Configuration, ACPI Configuration, IDE Configuration, PCIPnP
Configuration, Floppy Configuration, SuperIO Configuration, and USB Configuration.
Main
Advanced
BIOS SETUP UTILITY
H/W Monitor
Boot
Security
Exit
Configure CPU
Advanced Settings
WARNING : Setting wrong values in below sections
may cause system to malfunction.
CPU Configuration
Chipset Configuration
ACPI Configuration
IDE Configuration
PCIPnP Configuration
Floppy Configuration
SuperIO Configuration
USB Configuration
Enter
F1
F9
F10
ESC
Select Screen
Select Item
Go to Sub Screen
General Help
Load Defaults
Save and Exit
Exit
v02.54 (C) Copyright 1985-2003, American Megatrends, Inc.
Setting wrong values in this section may cause
the system to malfunction.
3.3.1 CPU Configuration
BIOS SETUP UTILITY
Advanced
Select how to set the
CPU host frequency.
CPU Configuration
CPU Host Frequency
Actual Frequency (MHz)
Spread Spectrum
Ratio Status
Ratio Actual Value
CPU Thermal Throttling
Hyper Threading Technology
[Auto]
[200]
[Disabled]
: Locked
: 18
[Enabled]
+F1
F9
F10
ESC
[Auto]
Select Screen
Select Item
Change Option
General Help
Load Defaults
Save and Exit
Exit
v02.54 (C) Copyright 1985-2003, American Megatrends, Inc.
CPU Host Frequency
While entering setup, BIOS auto detects the present CPU host frequency of
this motherboard. The actual CPU host frequency will show in the following
item.
Spread Spectrum
This item should always be [Disabled] for better system stability.
25
Ratio Status
This is a read-only item, which displays whether the ratio status of this
motherboard is “Locked” or “Unlocked”. If it shows “Unlocked”, you will find
an item Ratio CMOS Setting appears to allow you changing the ratio value
of this motherboard. If it shows “Locked”, then the item Ratio CMOS Setting will be hidden. If you use the ratio value to time the CPU frequency, it will
be equal to the core speed of the installed processor.
Ratio Actual Value
This is a read-only item, which displays the ratio actual value of this
motherboard.
CPU Thermal Throttling
You may select [Enabled] to enable P4 CPU internal thermal control mechanism to keep the CPU from overheated.
Hyper Threading Technology
To enable this feature, it requires a computer system with an Intel Pentium®4
processor that supports Hyper-Threading technology and an operating system that includes optimization for this technology, such as Microsoft® Windows ® XP. Set to [Auto] if using Microsoft® Windows® XP, or Linux kernel
version 2.4.18 or higher. This option will be hidden if the installed CPU does
not support Hyper-Threading technology.
3.3.2 Chipset Configuration
BIOS SETUP UTILITY
Advanced
Chipset Configuration
Options
DRAM Frequency
Flexibility Option
DRAM CAS# Latency
DRAM Command Rate
DRAM Bus Selection
[Auto]
[Disabled]
[Auto]
[2T Command]
[Auto]
DRAM Voltage
AGP Voltage
[Normal]
[High]
Primary Graphics Adapter
AGP Aperture Size
AGP Mode
AGP Fast Write
[PCI]
[64MB]
[Auto]
[Disabled]
PCI Delay Transaction
OnBoard LAN
OnBoard AC'97 Audio
[Disabled]
[Eabled]
[Auto]
133MHz (DDR266)
166MHz (DDR333)
200MHz (DDR400)
Auto
+F1
F9
F10
ESC
Select Screen
Select Item
Change Option
General Help
Load Defaults
Save and Exit
Exit
v02.54 (C) Copyright 1985-2003, American Megatrends, Inc.
DRAM Frequency
If [Auto] is selected, the motherboard will detect the memory module(s)
inserted and assigns appropriate frequency automatically. You may also
select other value as operating frequency: [133MHz (DDR 266)],
[166MHz (DDR 333)], [200MHz (DDR 400)].
26
Flexibility Option
The default value of this option is [Disabled]. It will allow better tolerance for
memory compatibility when it is set to [Enabled].
DRAM CAS# Latency
Use this item to adjust the means of memory accessing. Configuration
options: [Auto], [2.5], [2], and [3].
DRAM Command Rate
Use this to select among [2T Command] and [1T Command] for DRAM
Command Rate. The default value is [2T Command].
DRAM Bus Selection
The default value is [Auto], which will automatically select the proper access mode for the system. You may select between [Single Channel] and
[Dual Channel] if you have properly set the dual channel memory
configuration.
DRAM Voltage
Use this to select among [Normal] and [High] for DRAM Voltage. The default
value is [Normal].
AGP Voltage
Use this to select among [Normal] and [High] for AGP Voltage. The default
value is [High].
Primary Graphics Adapter
This allows you to select [PCI] or [AGP] as the primary graphics adapter.
The default vaule is [PCI].
AGP Aperture Size
It refers to a section of the PCI memory address range used for graphics
memory. It is recommended to leave this field at the default value unless the
installed AGP card’s specifications requires other sizes.
AGP Mode
The default value of this feature is set to [Auto]. If you install an 8X-AGP
card on this motherboard, you may select [Auto], [8X] or [4X] as the AGP
mode. If the installed AGP card is a 4X-AGP card, then you may set the AGP
mode as [Auto], [4X], [2X], or [1X].
AGP Fast Write
This allows you to enable or disable the feature of AGP fast write protocol
support.
PCI Delay Transaction
Enable PCI Delay Transaction feature will free the PCI Bus when the CPU is
accessing 8-bit ISA cards. Disable this feature when using ISA cards that
are not PCI 2.1 compliant.
27
OnBoard LAN
This allows you to enable or disable the onboard LAN feature.
OnBoard AC’97 Audio
Select [Auto] or [Disabled] for the onboard AC’97 Audio feature.
3.3.3 ACPI Configuration
BIOS SETUP UTILITY
Advanced
ACPI Configuration
Suspend To RAM
[Disabled]
Restore on AC / Power Loss
Ring-In Power On
PCI Devices Power On
PS / 2 Keyboard Power On
RTC Alarm Power On
[Power Off]
[Disabled]
[Disabled]
[Disabled]
[Disabled]
Select auto-detect or
disable the STR
feature.
+F1
F9
F10
ESC
Select Screen
Select Item
Change Option
General Help
Load Defaults
Save and Exit
Exit
v02.54 (C) Copyright 1985-2003, American Megatrends, Inc.
Restore on AC/Power Loss
Use this item to set the power state after an unexpected AC/power loss. If
[Power Off] is selected, the AC/power remains off when the power
recovers. If [Power On] is selected, the AC/power resumes and the system starts to boot up when the power recovers.
Ring-In Power On
Use this item to enable or disable COM Port Modem to turn on the system
from the power-soft-off mode.
PCI Devices Power On
Use this item to enable or disable PCI devices to turn on the system from the
power-soft-off mode.
PS/2 Keyboard Power On
Use this item to enable or disable PS/2 keyboard to turn on the system from
the power-soft-off mode.
RTC Alarm Power On
Use this item to enable or disable RTC (Real Time Clock) to power on the
system.
28
3.3.4 IDE Configuration
BIOS SETUP UTILITY
Advanced
IDE Configuration
OnBoard IDE Controller
Primary IDE Master
Primary IDE Slave
Secondary IDE Master
Secondary IDE Slave
[Both]
[Hard Disk]
[Not Detected]
[Not Detected]
[Not Detected]
DISABLED: disables the
integrated IDE
Controller.
PRIMARY: enables only
the Primary IDE
Controller.
SECONDARY: enables
only the Secondary IDE
Controller.
BOTH: enables both IDE
Controllers.
+F1
F9
F10
ESC
Select Screen
Select Item
Change Option
General Help
Load Defaults
Save and Exit
Exit
v02.54 (C) Copyright 1985-2003, American Megatrends, Inc.
OnBoard IDE Controller
You may enable either the primary IDE channel or the secondary IDE channel.
Or you may enable both the primary and the secondary IDE channels by
selecting [Both]. Set to [Disabled] will disable the both. Configuration options:
[Disabled], [Primary], [Secondary], [Both].
IDE Device Configuration
You may set the IDE configuration for the device that you specify. We will
use the “Primary IDE Master” as the example in the following instruction,
which can be applied to the configurations of “Primary IDE Slave”, “Secondary IDE Master”, and “Secondary IDE Slave” as well.
BIOS SETUP UTILITY
Advanced
Primary IDE Master
Device
Vendor
Size
LBA Mode
Block Mode
PIO Mode
Async DMA
Ultra DMA
S.M.A.R.T.
:Hard Disk
:ST340014A
:40.0 GB
:Supported
:16Sectors
:4
:MultiWord DMA-2
:Ultra DMA-5
:Supported
Type
LBA/Large Mode
Block (Multi-Sector Transfer)
PIO Mode
DMA Mode
S.M.A.R.T.
32Bit Data Transfer
[Auto]
[Auto]
[Auto]
[Auto]
[Auto]
[Disabled]
[Disabled]
Select the type
of device connected
to the system.
+F1
F9
F10
ESC
Select Screen
Select Item
Change Option
General Help
Load Defaults
Save and Exit
Exit
v02.54 (C) Copyright 1985-2003, American Megatrends, Inc.
29
TYPE
Use this item to configure the type of the IDE device that you specify.
Configuration options: [Not Installed], [Auto], [CD/DVD], and [ARMD].
[Not Installed]: Select [Not Installed] to disable the use of IDE device.
[Auto]: Select [Auto] to automatically detect the hard disk drive.
After selecting the hard disk information into BIOS, use a disk
utility, such as FDISK, to partition and format the new IDE hard
disk drives. This is necessary so that you can write or read
data from the hard disk. Make sure to set the partition of the
Primary IDE hard disk drives to active.
[CD/DVD]: This is used for IDE CD/DVD drives.
[ARMD]: This is used for IDE ARMD (ATAPI Removable Media Device),
such as MO.
LBA/Large Mode
Use this item to select the LBA/Large mode for a hard disk > 512 MB under
DOS and Windows; for Netware and UNIX user, select [Disabled] to
disable the LBA/Large mode.
Block (Multi-Sector Transfer)
The default value of this item is [Auto]. If this feature is enabled, it will
enhance hard disk performance by reading or writing more data during
each transfer.
PIO Mode
Use this item to set the PIO mode to enhance hard disk performance by
optimizing the hard disk timing.
DMA Mode
DMA capability allows the improved transfer-speed and data-integrity for
compatible IDE devices.
S.M.A.R.T.
Use this item to enable or disable the S.M.A.R.T. (Self-Monitoring, Analysis,
and Reporting Technology) feature. Configuration options: [Disabled], [Auto],
[Enabled].
32-Bit Data Transfer
Use this item to enable 32-bit access to maximize the IDE hard disk data
transfer rate.
30
3.3.5 PCIPnP Configuration
BIOS SETUP UTILITY
Advanced
Value in units of PCI
clocks for PCI device
latency timer
register.
PCI / PnP Configuration
PCI Latency Timer
PCI IDE BusMaster
[32]
[Enabled]
+F1
F9
F10
ESC
Select Screen
Select Item
Change Option
General Help
Load Defaults
Save and Exit
Exit
v02.54 (C) Copyright 1985-2003, American Megatrends, Inc.
PCI Latency Timer
The default value is 32. It is recommended to keep the default value unless
the installed PCI expansion cards’ specifications require other settings.
PCI IDE BusMaster
Use this item to enable or disable the PCI IDE BusMaster feature.
3.3.6 Floppy Configuration
In this section, you may configure the type of your floppy drive.
BIOS SETUP UTILITY
Advanced
Floppy Configuration
Floppy A
Floppy B
[1.44 MB 31 2"]
[Disabled]
Select the type of
floppy drive
connected to the
system.
+F1
F9
F10
ESC
Select Screen
Select Item
Change Option
General Help
Load Defaults
Save and Exit
Exit
v02.54 (C) Copyright 1985-2003, American Megatrends, Inc.
31
3.3.7 Super IO Configuration
BIOS SETUP UTILITY
Advanced
Configure Super IO Chipset
OnBoard Floppy Controller
Serial Port Address
Infrared Port Address
Parallel Port Address
Parallel Port Mode
EPP Version
ECP Mode DMA Channel
Parallel Port IRQ
OnBoard Game Port
OnBoard MIDI Port
Allow BIOS to Enable
or Disable Floppy
Controller.
[Enabled]
[3F8 / IRQ4]
[Disabled]
[378]
[ECP + EPP]
[1.9]
[DMA3]
[IRQ7]
[Enabled]
[Disabled]
+F1
F9
F10
ESC
Select Screen
Select Item
Change Option
General Help
Load Defaults
Save and Exit
Exit
v02.54 (C) Copyright 1985-2003, American Megatrends, Inc.
OnBoard Floppy Controller
Use this item to enable or disable floppy drive controller.
Serial Port Address
Use this item to set the address for the onboard serial port or disable it.
Configuration options: [Disabled], [3F8 / IRQ4], [2F8 / IRQ3], [3E8 / IRQ4],
[2E8 / IRQ3].
Infrared Port Address
Use this item to set the address for the onboard infrared port or disable it.
Configuration options: [Disabled], [2F8 / IRQ3], and [2E8 / IRQ3].
Parallel Port Address
Use this item to set the address for the onboard parallel port or disable it.
Configuration options: [Disabled], [378], and [278].
Parallel Port Mode
Use this item to set the operation mode of the parallel port. The default
value is [ECP+EPP]. If this option is set to [ECP+EPP], it will show the EPP
version in the following item, “EPP Version”. Configuration options:
[Normal], [Bi-Directional], and [ECP+EPP].
EPP Version
Use this item to set the EPP version. Configuration options: [1.9]
and [1.7].
ECP Mode DMA Channel
Use this item to set the ECP mode DMA channel. Configuration
options: [DMA0], [DMA1], and [DMA3].
Parallel Port IRQ
Use this item to set the IRQ for the parallel port. Configuration options:
[IRQ5] and [IRQ7].
32
OnBoard Game Port
Use this item to enable the Game Port or disable it.
OnBoard MIDI Port
Use this itme to select the address for the MIDI Port or disable it. Configuration options: [Disabled], [300], and [330].
3.3.8 USB Configuration
BIOS SETUP UTILITY
Advanced
USB Configuration
To enable or disable
the onboard USB
controllers.
USB Devices Enabled :
None
USB Controller
USB 2.0 Support
Legacy USB Support
[Enabled]
[Enabled]
[Disabled]
+F1
F9
F10
ESC
Select Screen
Select Item
Change Option
General Help
Load Defaults
Save and Exit
Exit
v02.54 (C) Copyright 1985-2003, American Megatrends, Inc.
USB Controller
Use this item to enable or disable the use of USB controller.
USB 2.0 Support
Use this item to enable or disable the USB 2.0 support.
Legacy USB Support
Use this item to enable or disable the support to emulate legacy I/O
devices such as mouse, keyboard,... etc. Or you may select [Auto] so
that the system will start to auto-detect; if there is no USB device
connected, “Auto” option will disable the legacy USB support.
33
3.4 Hardware Health Event Monitoring Screen
In this section, it allows you to monitor the status of the hardware on your system,
including the parameters of the CPU temperature, motherboard temperature, CPU fan
speed, chassis fan speed, and the critical voltage.
Main
Advanced
BIOS SETUP UTILITY
H/W Monitor
Boot
Security
Exit
Hardware Health Event Monitoring
CPU Temperature
M / B Temperature
: 56 C / 133 F
: 31 C / 87 F
CPU Fan Speed
Chassis Fan Speed
: 2463 RPM
: N/A
Vcore
+ 3.30V
+ 5.00V
+ 12.00V
:
:
:
:
1.629V
3.306V
5.067V
11.890V
Select Screen
Select Item
General Help
Load Defaults
Save and Exit
Exit
F1
F9
F10
ESC
v02.54 (C) Copyright 1985-2003, American Megatrends, Inc.
3.5 Boot Screen
In this section, it will display the available devices on your system for you to configure the boot settings and the boot priority.
Main
Advanced
BIOS SETUP UTILITY
H/W Monitor
Boot
Boot Settings
Security
Exit
Configure Settings
during System Boot.
Boot Settings Configuration
Boot Device Priority
Removable Drives
Enter
F1
F9
F10
ESC
Select Screen
Select Item
Go to Sub Screen
General Help
Load Defaults
Save and Exit
Exit
v02.54 (C) Copyright 1985-2003, American Megatrends, Inc.
34
3.5.1 Boot Settings Configuration
BIOS SETUP UTILITY
Boot
Boot Settings Configuration
Boot From Network
Bootup Num-Lock
To enable or disable the
boot from network feature.
[Disabled]
[On]
+F1
F9
F10
ESC
Select Screen
Select Item
Change Option
General Help
Load Defaults
Save and Exit
Exit
v02.54 (C) Copyright 1985-2003, American Megatrends, Inc.
Boot From Network
Use this item to enable or disable the Boot From Network feature.
Boot Up Num-Lock
If this item is set to [On], it will automatically activate the Numeric Lock
function after boot-up.
3.5.2 Boot Device Priority
In this section, you may specify the boot sequence from the available devices
in your system.
BIOS SETUP UTILITY
Boot
Boot Device Priority
1st Boot Device
2nd Boot Device
3rd Boot Device
[1st FLOPPY DRIVE]
[HDD: PM-MAXTOR 6L08]
[CD / DVD]
Specifies the boot
sequence from the
available devices.
A device enclosed in
parenthesis has been
disabled in the
corresponding type
menu.
+F1
F9
F10
ESC
Select Screen
Select Item
Change Option
General Help
Load Defaults
Save and Exit
Exit
v02.54 (C) Copyright 1985-2003, American Megatrends, Inc.
Likewise, you may also specify the boot sequence from the available devices
for the hard disk drives, the removable drives, and the CD/DVD drives.
35
3.6 Security Screen
In this section, you may set or change the supervisor/user password for the system.
For the user password, you may also clear it.
Main
Advanced
BIOS SETUP UTILITY
H/W Monitor
Boot
Security Settings
Supervisor Password
User Password
Security
Exit
Install or Change the
password.
: Not Installed
: Not Installed
Change Supervisor Password
Change User Password
Clear User Password
Enter
F1
F9
F10
ESC
Select Screen
Select Item
Change
General Help
Load Defaults
Save and Exit
Exit
v02.54 (C) Copyright 1985-2003, American Megatrends, Inc.
36
3.7 Exit Screen
Main
Advanced
BIOS SETUP UTILITY
H/W Monitro
Boot
Exit Options
Security
Exit
Exit system setup
after saving the
changes.
Save Changes and Exit
Discard Changes and Exit
Discard Changes
F10 key can be used
for this operation.
Load Optimal Defaults
Enter
F1
F9
F10
ESC
Select Screen
Select Item
Go to Sub Screen
General Help
Load Defaults
Save and Exit
Exit
v02.54 (C) Copyright 1985-2003, American Megatrends, Inc.
Save Changes and Exit
When you select this option, it will pop-out the following message, “Save
configuration changes and exit setup?” Select [OK] to save the changes
and exit the BIOS SETUP UTILITY.
Discard Changes and Exit
When you select this option, it will pop-out the following message, “Discard changes and exit setup?” Select [OK] to exit the BIOS SETUP UTILITY
without saving any changes.
Discard Changes
When you select this option, it will pop-out the following message, “Discard changes?” Select [OK] to discard all changes.
Load Optimal Defaults
When you select this option, it will pop-out the following message, “Load
optimal defaults?” Select [OK] to load the default values for all the setup
configurations.
37
Chapter 4 Software Support
4.1
Install Operating System
This motherboard supports various Microsoft® Windows® operating systems: 98 SE / ME / 2000
/ XP. Because motherboard settings and hardware options vary, use the setup procedures in this
chapter for general reference only. Refer to your OS documentation for more information.
4.2
Support CD Information
The Support CD that came with the motherboard contains necessary drivers and useful utilities
that enhance the motherboard features.
4.2.1 Running The Support CD
To begin using the support CD, insert the CD into your CD-ROM drive. The CD automatically displays the Main Menu if “AUTORUN” is enabled in your computer. If the Main
Menu did not appear automatically, locate and double click on the file “ASSETUP.EXE”
from the BIN folder in the Support CD to display the menus.
4.2.2 Drivers Menu
The Drivers Menu shows the available devices drivers if the system detects installed
devices. Please install the necessary drivers to activate the devices.
4.2.3 Utilities Menu
The Utilities Menu shows the applications software that the motherboard supports. Click on
a specific item then follow the installation wizard to install it.
4.2.4 “LGA 775 CPU Installation Live Demo” Program
This motherboard is equipped with Intel LGA 775 socket, which is a new CPU socket
interface that Intel has released. Since it has several tiny pins, whcih are easily to be
damaged by improper handling, ASRock sincerely presents you a clear installation guide
through this “LGA 775 CPU Installation Live Demo”. We hope you may check this live
demo program before you start the installation of LGA 775 CPU in order to reduce the risks
of CPU and motherboard damages caused by any improper handling. To see this Live
Demo, you can run Microsoft® Media Player® to play the file. You may find this Live Demo
in the motherboard’s Support CD through the following path:
..\ MPEGAV \ LGA775INST.DAT
4.2.5 Contact Information
If you need to contact ASRock or want to know more about ASRock, welcome to visit
ASRock’s website at http://www.asrock.com; or you may contact your dealer for further
information.
38