DC-DC Converter - Axiomatic Technologies Corporation

DC-DC Converter - Axiomatic Technologies Corporation
TECHNICAL DATASHEET #TD3003AX
DC-DC Converter
(48 VDC to 24 VDC)
P/N: PSU5K
Clean 24 VDC power in a rugged package
















Wide input operating voltage 35 to 65 VDC (48 VDC nominal)
Up to 80 VDC input versions available
Conditioned output of 24 VDC with low ripple
High current output capability (13 A nominal, 18 A peak)
315 Watts output power
Switch mode operation delivers very high efficiency >95%
Design manages heat dissipation avoiding forced cooling
Reverse polarity protection
Short circuit protection
Robust, rugged and highly reliable
Compact size for ease of mounting in confined spaces
Suitable for moist, high shock and vibration environments
Operational from -40 to 85C
IP65 protection
UL 583 recognized
Low emissions
Application: Designed to
interface between 48V batteries
and 24V electrical systems such as
24V solenoids, relays and other
electrical systems.
Description:
The DC-DC Converter provides clean 24 VDC power suitable for 24V solenoids, relays and other
electrical systems. For operation under the most harsh and demanding conditions, the IP65 rated unit is fully sealed
and potted in an enclosure to protect against moisture, shock and vibration. Power from a battery or other source of
48 VDC is converted to a 24 VDC output regulated to 0.5%. The unit has a high current output capability of 13 Amp
nominal (18 Amp peak). The device manages heat dissipation and requires no forced cooling systems. Short circuit
and reverse polarity protection are provided. The compact unit is designed with extremely rugged surge and transient
suppression in addition to sustained over/under voltage protection. With a nameplate rating of 315 Watts of output
power, the DC-DC Converter features proprietary dual-phase topology for a high efficiency of >95%.
Ordering Part Numbers:
Converter with Wire Harness KIT: PSU5K (SMP-BAC-48VD-24VD-01, WH-DTP06-4S-S-2M)
Items can also be ordered individually.
Converter: SMP-BAC-48VD-24VD-01
Mating Wire Harness, 2 m: WH-DTP06-4S-S-2M
Technical Specifications:
All specifications are typical at nominal input voltage and 25 degrees C unless otherwise specified.
Input Specifications
Power Source
Operating Voltage Range
Maximum Input Current
Inrush Current
Output Specifications
48 VDC nominal
(80 VDC versions
available)
36 to 65 VDC
10 ADC @ 36 VDC,
13 A I-output
None
Reverse Voltage
Protection
Over-voltage Protection
Provided
Under-voltage Protection
Provided
Isolation
Not provided
Provided
Nameplate Rating
(Output Power)
315 Watts nominal
(435 Watts peak)
Output Current (DC)
Output Voltage
13 A continuous (18 A peak)
26 VDC (nominal)  3%
(24 - 28 VDC)
VO(RIPPLE) < 100 mVpp
Output Voltage Ripple
Turn-on Time
(with full load)
Turn-on Overshoot
Stability
Transient Response
Short Circuit Protection
Overload Protection
100 msec. Maximum / 5% of final value
None
Stable at all load conditions
(no minimum load required)
200 mV/1.5 ms (No Load to Full Load)
100 mV/1 ms (50% - 100% Load)
Provided
Output fold back to 10 A @ 0 Ohms
General Specifications
Efficiency
Operating Temperature
Humidity
UL recognition
Protection rating
Electrical Connection
Weight
Dimensions
>95%
-40 to 85C (-40 to 185F)
0-99% relative humidity (non-condensing)
UL583 for use on Type E, ES, or EE Battery Powered Industrial Trucks
IP65
4 pin Deutsch connector P/N: DTP04-4P-L012
Power +, Power –
Output +, Output –
See page 3 for pinout.
A mating plug assembly with 12 AWG unterminated lead wires is available.
Ordering P/N: WH-DTP06-4S-S-2M
(The mating plug assembly is comprised of Deutsch P/N: DTP06-4S, WP4S and four
contact sockets 0462-203-12141 with 2 meters (6.5 ft.) of 12 AWG lead wire,
unterminated.)
Contact the manufacturer for application-specific wiring.
1.4 kg (3.08 lbs.)
5.50 x 6.93 x 2.37 inches (W x L x H excluding connector)
139.7 x 176.0 x 60.3 mm
Installation
Set up
1. A maximum 15A fuse is recommended in the primary circuit to provide protection for the primary wiring.
2. Use four ¼-20 1 inch screws to mount the converter.
3. Snap the mating plug connector with wiring harness into the receptacle mounted on the converter.
4. Once the load is ready to receive power, turn on the power source to the converter.
TD3003AX
2
Grounding
Protective Earth (PE) must be connected to the grounding stud
to reduce the risk of electric shock. The conductor providing
the connection should have a ring lug and wire larger than or
2
equal to 4 mm (12 AWG). The ring lug should be placed
between the nut and a star washer. (To secure the ground
strap, use an 8-32 “K-LOK” locknut, stainless steel, 3/8” O.D.)
All chassis grounding should go to a single ground point
designated for the machine and all related equipment.
Mounting
The ground strap that provides a low impedance path for EMI
should be a ½ inch wide, flat, hollow braid, no more than 12
inches long with a suitable sized ring lug for the module’s
grounding lug. It may be used in place of the PE grounding
conductor and would then perform both PE and EMI grounding
functions.
Mounting ledges include holes sized for ¼ inch or M6 bolts.
The bolt length will be determined by the end-user’s mounting
plate thickness. Typically ¾ inch (20 mm) is adequate.
If the module is mounted without an enclosure, it should be
mounted vertically with connectors facing left and right to
reduce likelihood of moisture entry.
All field wiring should be suitable for the operating temperature
range of the module.
Install the unit with appropriate space available for servicing
and for adequate wire harness access (6 inches or 15 cm) and
strain relief (12 inches or 30 cm).
Mechanical Drawing
Pin Out
Specifications are indicative and subject to change. Actual performance will vary depending on the application and operating
conditions. Users should satisfy themselves that the product is suitable for use in the intended application. All our products carry a
limited warranty against defects in material and workmanship. Please refer to our Warranty, Application Approvals/Limitations and
Return Materials Process as described on www.axiomatic.com/service.html.
Form: TD3003AX-09/30/13 2013 Axiomatic Technologies Corporation
TD3003AX
3
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement