Installation manual: CA-1803BT “Athos”

Before installation

This is the basic version of the installation manual and programming sequences.On the web site www.jablotronalarms.com

in the download section you can find a full version of this manual or you can find it included in the installation kit on CD / DVD. If you have no experience with CA-1803 installation, we recommend you to read

the extended version of the manual to know all the parameters well.

The immobilizer relay contact of car alarm is connected only in disarmed mode and if the ignition is on. Do not block circuits that are under voltage while the ignition is off. It could cause a serious damage of the vehicle.

The car alarm should only be installed by a professional installer. It is suitable for cars with a dashboard voltage supply of 12V or 24V with a negative ground connection. During the first power-up, the value of supply voltage is read and the inputs are set to default settings. The alarm is designed to be installed inside the car.

For cars with a voltage supply of 24V, the following restrictions apply to

car alarm installation:

1. It is not possible to connect a hands-free set of type HF-03.

2. When used for acoustic signalling, the SIR output is switched to the power supply voltage. Consequently, this output switches to 24V, so it is necessary to use a siren of type SA-606-24V instead of the SA-530 which is supplied in the standard package. In this case it is necessary to set the confirmation beeps to 100 ms.

Configuration table

SIM entry*

RESET EN 1

(After which, the entry is erased from the SIM)

Not applicable

SMS instruction Text

MASTER RESET EN 1

MASTER UC uuuu

Description

Mode setting. RESET 1 = alarm has its own remote control and provides signals for central locking.

RESET 2 = alarm is operated by an original remote controller for central locking. RESET 3 = GSM

pager for cars with an installed car alarm. Performing the RESET instruction is indicated by 4 beeps.

Consequently, all settings, enrolled remote controllers and wireless detectors will be erased.

User code setting – the code allows you to operate the alarm remotely via SMS from unauthorized phones. uuuu is a new user code, 4 to 8 letters (A–Z & 0–9, case insensitive). Factory default user code is USER

Not applicable MASTER MC xxxx

TELn xx...x

DIALn xx...x

DIP abcdefghij

SET abcdefghij

MASTER TELn xx...x

MASTER DIALn xx...x

MASTER DIP abcdefghij

MASTER SET abcdefghij

DIP parameters

Master code setting –xxxx is a new master code (A–Z & 0–9, case insensitive). The code allows you to change the maintenance settings for the car alarm. Factory default master code is MASTER

Setting of phone numbers to report alarms to n = 1 to 4

Setting the phone numbers to dial using Hands free. n = A, B, 1, 2

DIP parameter entry – see the DIP table

SET parameter entry – see the SET table

DIP

A

C

D

E

F

G

H

I

J

Description

0 1

0 = silent arming/disarming without siren chirps

1 = 10 ms siren chirps when arming/disarming (non backed-up siren)

2, 3, 4 ... 9 = siren chirps when arming/disarming (a siren of another type) lasting 20, 30, 40, 50, 100, 200, 300 or 500 ms

Audible alarm

SMS alarm report only

SMS alarm report and siren sound phone call

SMS remote control not confirmed by SMS reply

SMS remote control instructions confirmed by SMS reply

0 = arming control by dialling-in disabled

1 = arming control by dialling from TEL1 enabled

2 = arming control by dialling from TEL1 and TEL2 enabled

3 = arming control by dialling from TEL1, TEL2 and TEL3 enabled

4 = arming control by dialling from all TEL1 to TEL4 enabled

Arming control by dialling in (see E)

Arming control by dialling in is not confirmed by

SMS

User can not change SMS

Texts is confirmed by SMS to the phone which called the car alarm

User can change SMS texts by TXT

Sequence

REARM disabled

If the car is not entered within 1 minute after disarming, it will REARM

0 = Immobilization by arming and by SMS instruction

1 = Immobilization by arming and automatically 5 minutes after ignition is turned off (AUTOIMO) and also by SMS instruction

2 = Immobilization only by SMS instruction

3 = Immobilization and also by SMS instruction. If disarmed and ignition is turned off for more than 60 minutes the SMS STATUS is sent as an alert to possible forgotten arming.

Self-location disabled

The car’s location will be sent by SMS after an IMO instruction has been performed. or if the car stops after an immobilization

SMS instruction

Bold marked values = factory default

Steps to enroll RC-8x controllers:

1. The car alarm should be disarmed, with the ignition on.

2. Send the SMS instruction MASTER LEARN RC

3. The car alarm beeps 3 times and an LED starts to flash.

4. The RC-8x controller is enrolled by pressing buttons and simultaneously for approx. 3 sec. A siren chirp confirms the enrollment. By enrolling the first remote control all other remote controls previously enrolled will be erased (so enroll all the controllers intended for use, one by one).

5. Exit enrollment by turning the ignition off. The alarm confirms the enrollment by sending an SMS message to authorized phones TEL1 to TEL4.

SET parameters

Description

SET

0 1

A 0 = open door signalling and INP activation while arming are both disabled

1 = open door signalling and INP activation while arming are both enabled

2 = INP activation while arming enabled, open door signalling enabled with a 10 second delay

3 = INP activation while arming enabled, open door signalling disabled

B Voltage detector disabled Voltage-drop detector enabled

C lock / unlock signal duration (Reset 1)

0 = 0.5 / 0.5 sec (suitable for electromagnetic locks)

1 = 4 / 4 sec (suitable for pneumatic locks)

2 = 60 / 0.5 sec (suitable for automatic window closing)

D DOOR input logic:

1 = activated by falling edge (grounding)

2 = activated by rising edge (disconnecting from GND)

1 = activated by falling edge (grounding)

2 = activated by rising edge (disconnecting from GND)

0 = activated by falling edge (grounding), it triggers an alarm also if disarmed (24 hour reaction)

1 = activated by falling edge (grounding)

2 = activated by rising edge (disconnecting from GND)

G Central locking input logic: (Reset 2)

1 = activated by falling edge (grounding)

2 = activated by rising edge (disconnecting from GND)

H 0 = confirmation by turn lights for disarming is needed (Reset 2)

1 = confirmation by turn lights for arming and disarming is needed

2= confirmation by turn lights for arming and disarming is not needed so INP1 can be used as an alarm input

I When armed, no monitoring of

GPS location changes

GPS location changes are

monitored when armed

J 0 = AUX output is a bus for communication with CR-11A modules

1 = AUX output provides power for external sensors

Bold marked values = factory default

Steps to enroll l detectors:

1. The car alarm should be disarmed, ignition on.

2. To enroll the internal detectors, send the SMS command MASTER LEARN

INT (To enroll the external detectors, send the SMS command MASTER

LEARN EXT )

3. The car alarm beeps 3 times and an LED starts to flash.

4. You can enroll a new detector to the system by inserting its batteries.If you enroll a first detector, you will erase all detectors from the associated groups (enroll all of them, which will be used in the group in sequence).

5. Exit enrollment by turning the ignition off. The alarm confirms enrollment by sending an SMS message to authorized phones TEL1 to TEL4.

GSM car alarm CA-1803BT „Athos 1/6 MHF58202

Functions related to GPS

Location detection using GPS

An example of an instruction sent from an authorized phone: GPS

An example of response: Car alarm reports: Location:

(GMT:3.12.10:35) 50*43.495N;15*11.253E;515;50, Time:3.12.05 11:35

(GMT:3.12.10:35)

50*43.495N;15*11.253E

515

Greenwich Mean Time (mean meridian) latitude and longitude

altitude (approximated)

Time:3.12.05 11:35 current local time

 After this sequence has been sent once, the car alarm will check the balance automatically every xx days and if the balance is lower than yyy the user will be notified (TEL1)

 If the CREDIT instruction is enabled in the above way, the user can also obtain the current balance by the instruction CREDIT

 To disable the automatic balance checking set the time period “xx” to 00.

Reset GSM

If you need to disconnect and then reconnect the GSM module to the

GSM network, then use the command “MASTER RESET GSM”.

This does not affect any settings and is typically used for GPRS activation or charging up credit. This command always requires the

Master code.

Time zone setting

To adjust the time information to local time, time zone setting is possible. The car alarm adds/subtracts the time shift, expressed in hours, to the GMT time (for middle Europe: +2 hours in summer time,

+1 hour in winter time).

Instruction: MASTER TIME ±xy xy is the time shift in hours -3,-2 …+1,+2 relative to GMT

MASTER TIME GSM turns on automatic setting via incoming SMS.

Integrated Bluetooth module (BT)

Service instruction

The DINFO instruction allows you to obtain current settings, information about the quality of the GSM signal, the registration code for GSMLink devices and some other parameters. This command always requires the Master code.

Example of instruction: MASTER DINFO

Example of response: Car alarm reports: CA-1803A, SN:123456,

SV:01, LV:03, RK:ABCDE-12345-FG67, R:01, GSM:25,GPS:5,

Time:3.2.06 11:35

CA-1803A

SN:123456

SV:01 car alarm version identification number of the product

software version

When disarmed and with the ignition key on, the car alarm sends

GPS coordinates via the BT which can be used for navigation. The car alarm authorization code for device-pairing is 0000. The ignition key must be on during the pairing process.

Internet remote access

RK: ABCDE-12345-FG67

R:01

GSM:25 registration code for GSMLink current Reset mode of the device instant quality of GSM signal (ranging from 0 to 32 (best))

GPS:5 number of visible satelites (0-16)

The web site www.GSMLink.cz enables car alarm remote control

(to users) and setting (to installers).

To get internet access to an installed and powered car alarm you will first be asked to register your car alarm on the first page. You will find a unique registration code for your car alarm on the warranty card.

Additional features

Specification

Power supply 12/24V DC (8-32V)

Stand-by consumption

Immobilization

max. 20 mA

8A permanently, 12A intermittently

Complies with ECE Regulation No. 97.00

Can be operated according to ERC/DEC98(20,21), ERC REC 70-03

Pre-paid SIM card balance

It is recommended not to use prepaid cards in the car alarm. If you have no other choice than prepaid cards, you can enable the CREDIT

EMC

Radio interference

EN 55022, EN 50130-4

ETSI EN 301 419-1, EN 301 511, ETSI EN 300 220

ETSI EN 300 328 instruction by the following sequence:

MASTER CREDIT uuu..u xx yyy zz

E

8

97 RAI-01 4532 where: uuu…u is the provider’s code to obtain the balance xx is the time period (in days) for regular checking

JABLOTRON ALARMS a.s. hereby declares that the CA-1803BT is in yyy is the threshold level below which the balance is compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC and 1995/56/EC The original of the reported to the user (TEL1) conformity assessment can be found at www.jablotron.com

, Technical zz is the position of the first digit of the balance in the

Support section reply SMS from the provider

Note: Although this product does not contain any harmful materials we suggest you return the product to the dealer or directly to the producer after use.

GSM car alarm CA-1803BT „Athos“ 2/2 MHF58202