LG | 42PX-3RV | Datasheet | LG 42PX-3RV plasma panel

PLASMA TV
OWNER’S MANUAL
Please read this manual carefully before operating your set.
Retain it for future reference.
Record model number and serial number of the set.
See the label attached on the back cover and quote this information to your dealer when you require service.
Model number
Serial number
:
:
P/NO : 3828VA0541F (MF056C, 138M TX) a
Safety Warnings
Safety Instructions
WARNING
W
Do not place the set in direct sunlight or near heat
sources such as heat registers, stove and so on.
- This may cause a fire.
Do not use the set in damp place such as a bathroom
or any place where it is likely to get wet.
- This may cause a fire or could give an electric shock.
Do not use water while cleaning the set.
- This may cause damaged the set or could give an electric
shock.
In case of smoke or strange smell from the set, switch
it off ,unplug it from the wall outlet and contact your
dealer or service center.
- This may cause a fire or could give an electric shock.
Bend antenna cable between inside and outside
building to prevent rain from flowing in.
- This may cause water damaged inside the set and could give an
electric shock.
Do not attempt to service the set yourself. Contact
your dealer or service center.
- This may cause damaged the set or could give an electric
shock.
Earth wire should be connected.
- If the earth wire is not connected, there is possible a danger of
electric shock caused by the current leakage.
- If grounding methods are not possible, a separate circuit breaker should be employed and installed by a qualified electrician.
Power
supplier
During storm activity, unplug the set from the wall
outlet and don’t touch an antenna cable.
- This may cause damaged the set or could give an electric
shock.
DISCONNECTING DEVICE FROM MAINS
- Mains plug is the disconnecting device. The plug must remain
readily operable.
Short-circuit
breaker
- Do not connect ground to telephone wires, lightning rods or gas
pipe.
Apparatus shall not be exposed to dripping or splashing and no objects filled with liquids, such as vases,
shall be placed on the apparatus.
Do not insert any object into the exhaust vent.
- This may cause a fire or could give an electric shock.
Do not place heavy objects on the set.
- This may cause serious injury to a child or adult.
WARNING in U.K. only
*
This set is supplied with a BS 1363 approved 13 amp mains plug, fused at 13 amp. When replacing the fuse
always use a 13 amp BS 1362, BSI or ASTA approved type. Never use this plug with the fuse cover omitted. To
obtain a replacement fuse cover contact your dealer or “LG Electronics U.K. Ltd.” If the type of plug supplied is not
suitable for the mains sockets in your home, then the plug should be removed and a suitable type fitted.
A mains plug removed from the mains lead of this set must be destroyed. A mains plug with bared wires is
hazardous if inserted in a mains socket. Do not connect either wire to the earth pin, marked with the letter E or
with the earth symbol
or coloured green or green and yellow. If any other plug is fitted, use a 13 amp fuse,
either in the plug, or at the distribution board.
The wires in this mains lead are coloured in accordance with the following codes: BLUE: NEUTRAL, BROWN: LIVE
As the colours of the wires in the mains lead of this set may not correspond with the coloured marking identifying the terminals in your plug, proceed as follows: The wire which is coloured blue must be connected to the terminal which is marked with the letter N or coloured black. The wire which is coloured brown must be connected
to the terminal which is marked with the letter L or coloured red.
2 PLASMA TV
ENGLISH
Safety Warnings
* Safety instructions have two kinds of information, and each meaning of it is as below.
WARNING The violation of this instruction may cause serious injuries and even death.
NOTES
The violation of this instruction may cause light injuries or damage of the
product.
Take care of danger that may happen under specific condition.
NOTES
Never touch the power plug with a wet hand.
- This may cause an electric shock.
Ensure the power cord doesn’t trail across any hot
objects like a heater.
- This may cause a fire or an electric shock.
Disconnect from the mains and remove all connections before moving.
Do not plug in unit if power cord or plug is damaged or
the connecting part of the power outlet is loose.
Do not place the set in a built-in installation such as a
bookcase or rack.
- This may cause a fire or an electric shock.
- Ventilation required.
Dispose of used batteries carefully to prevent a child
from eating them.
- In case of a child eating them, contact doctor immediately.
When moving the set assembled with speakers do not
carry holding the speakers.
- This may cause the set to fall, causing serious injury to a child or
adult, and serious damage to the Monitor.
Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners.
When installing the set on a table, be careful not to
place the edge of its stand on the end of the table.
- This may cause damage the set or could give an electric shock.
- This may cause the set to fall, causing serious injury to a child or
adult, and serious damage to the set.
Contact the service center once a year to clean the
internal part of the set.
- Accumulated dust can cause mechanical failure.
The distance between eyes and the screen should be
approx. 5 ~ 7 times the diagonal length of the screen
away.
- If not, eyes will strain.
Unplug the set from the wall outlet when it is left unattended
and unused for long periods of time or occurred a state of
emergency.
Do not place an outside antenna in the vicinity of overhead power lines or other electric light or power circuits.
- Accumulated dust may cause a fire or an electric shock from
deterioration through electric leakage.
- This may cause an electric shock.
There should be enough distance between an outside
antenna and power lines to keep the former from
touching the latter even when the antenna falls.
- This may cause an electric shock.
Do not pull the plug not the cord when disconnecting.
- This may cause a fire.
Owner’s Manual 3
Contents
Contents
Safety Warnings
Safety Instructions . . . . . . . . . . . . . . . . . . . . . . .2~3
Introduction
Remote Control Key Functions . . . . . . . . . . . . . . . .6
Location and Function of Controls . . . . . . . . . . .7~8
Installation
External Equipment Viewing Setups . . . . . . . . .9~12
Displayable Monitor Specification . . . . . . . . . . . . .13
HDMI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14~15
Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
Installation Options . . . . . . . . . . . . . . . . . . . . . . .17
Operation
Turning on the Set . . . . . . . . . . . . . . . . . . . . . . . .18
On-Screen Menu Language Selection (option) . . .18
Channel Menu Options
Auto Programme Tuning . . . . . . . . . . . . . . . . . . .19
Manual Programme Tuning . . . . . . . . . . . . . . . . .19
Fine Tuning . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
Assigning a Station Name . . . . . . . . . . . . . . . . . .20
Booster (option) . . . . . . . . . . . . . . . . . . . . . . . . . .20
Programme Edit . . . . . . . . . . . . . . . . . . . . . . . . . .21
Favourite Programme . . . . . . . . . . . . . . . . . . . . .21
Calling up the Programme Table . . . . . . . . . . . . .21
Picture Menu Options
PSM (Picture Status Memory) . . . . . . . . . . . . . . .22
CSM (Colour Status Memory) . . . . . . . . . . . . . . .22
Manual Colour Temperature Control . . . . . . . . . .22
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
sRGB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
ACM (Active Colour Management) . . . . . . . . . . . .23
Manual Picture Control . . . . . . . . . . . . . . . . . . . .23
Sound Menu Options
SSM (Sound Status Memory) . . . . . . . . . . . . . . . .24
BBE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24
AVL (Auto Volume Leveler) . . . . . . . . . . . . . . . . .24
Adjusting Sound Control . . . . . . . . . . . . . . . . . . .24
TV speaker . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25
Stereo/Dual Reception . . . . . . . . . . . . . . . . . . . . .25
NICAM Reception (option) . . . . . . . . . . . . . . . . . .25
Time Menu Options
Setting the Clock . . . . . . . . . . . . . . . . . . . . . . . . .26
Setting the On/Off Timer . . . . . . . . . . . . . . . . . . .26
Auto Sleep . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26
Sleep Timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26
Special Menu Options
Child Lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27
ISM (Image Sticking Minimization) Method . . . . . .27
Low Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28
Demo . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28
Screen Menu Options
Auto Configure . . . . . . . . . . . . . . . . . . . . . . . . . .29
Manual Configure . . . . . . . . . . . . . . . . . . . . . . . .29
Selecting Wide VGA/XGA mode . . . . . . . . . . . . .29
Setting Picture Format . . . . . . . . . . . . . . . . . . . . .30
Picture Size Zoom . . . . . . . . . . . . . . . . . . . . . . . .30
Screen Position . . . . . . . . . . . . . . . . . . . . . . . . . .31
Cinema . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31
NR (Noise Reduction) . . . . . . . . . . . . . . . . . . . . .31
Initializing (Reset to original factory value) . . . . . .31
Teletext (option)
Switch on/off . . . . . . . . . . . . . . . . . . . . . . . . . . . .32
SIMPLE Text (option) . . . . . . . . . . . . . . . . . . . . . .32
TOP Text (option) . . . . . . . . . . . . . . . . . . . . . . . . .32
FASTEXT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33
Special Teletext Functions . . . . . . . . . . . . . . . . . .33
Miscellaneous
External Control Device Setup . . . . . . . . . . . .34~39
IR Code (NEC Format) . . . . . . . . . . . . . . . . . .40~41
Troubleshooting Checklist . . . . . . . . . . . . . . . . . .42
Product Specifications . . . . . . . . . . . . . . . . . . . . .43
Disposal of your old appliance
After reading this manual, keep it in a place
where the user can refer
to easily.
4 PLASMA TV
1. When this crossed-out wheeled bin symbol is attached to a product it
means the product is covered by the European Directive 2002/96/EC.
2. All electrical and electronic products should be disposed of separately
from the municipal waste stream via designated collection facilities
appointed by the government or the local authorities.
3. The correct disposal of your old appliance will help prevent potential
negative consequences for the environment and human health.
4. For more detailed information about disposal of your old appliance,
please contact your city office, waste disposal service or the shop
where you purchased the product.
Introduction
ENGLISH
Introduction
What is a Plasma Display ?
If voltage is inputted to gas in glass panels, ultraviolet rays are outputted and fused with a fluorescent substance. At this moment,
light is emitted. A Plasma Display is a next generation flat Display using this phenomenon.
160° - Wide angle range of vision
A Plasma Display provides more than 160° angle range of vision so that you can get a picture without distortion from any
direction.
Easy installation
A Plasma Display is much lighter and smaller than other same class products so that you can install the Plasma Display
in the desired place.
Big screen
The screen of a Plasma Display is 42" (or 50") so that you can get vivid experience as if you are in a theater.
Multimedia Plasma Display
A Plasma Display can be connected with a computer so that you can use it as a screen for conference, game, internet
and so on.
The explanation about coloured dots may be present on PDP screen
The PDP which is the display device of this product is composed of 0.9 to 2.2 million cells and a few cell defects can occur
in the manufacture of the PDP. Several coloured dots visible on the screen would be acceptable, in line with other PDP
manufacturers and would not mean that the PDP is faulty. We hope you will understand that the product which corresponds to this standard is regarded as acceptable. It means that it could not be changed or refunded.
We promise that we'll do our best to develop our technology to minimize the cell defects.
The explanation about noise of 42" (or 50") PDP (option)
In the same way that a fan is used in a PC to keep the CPU cool, the PDP is equipped with cooling fans to improve the
reliability of this product. Therefore, a certain level of noise could occur when the fan is operated. This noise doesn't have
any negative effect on its efficiency and liability and it's also determined to have no difficulty while using this product. The
noise from the fans is normal in the operation of this product. We hope you will understand that a certain level of noise is
acceptable. It means that it is not changeable nor refundable.
WARNING
This is Class B product. In a domestic environment this product may cause radio interference in which
case the user may be required to take adequate measures.
WARNING
TO REDUCE THE RISK OF FIRE AND ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO
RAIN OR MOISTURE.
Owner’s Manual 5
Introduction
Remote Control Key Functions
- When using the remote control aim it at the remote control sensor of the set.
- There's maybe a defect in consecutive operation of remote control in specified brightness according to this set feature.
POWER
switches the set on from standby or
off to standby.
MUTE
Switches the sound on or off.
MULTIMEDIA
Selects the Component, RGB or
HDMI modes.
switches the set on from standby.
TV/AV
Selects the TV, AV, Component, RGB
or HDMI modes.
switches the set on from standby.
MUTE
POWER
TV/AV MULTIMEDIA I/II
LIST
ARC
MENU
PR
PSM
Adjusts the factory preset picture
according to the room.
Q.VIEW
Returns to the previously viewed programme.
Note : This function works only when
Favourite programme is set to
Off. Otherwise each press of this button will select a stored favorite programme.
ARC
Changes the picture format.
MENU
Displays on screen menus one by
one.
Exits the current menu.
Memorizes menu changes.
LIST
Displays the programme table.
D / E (Programme Up/Down)
selects a programme or a menu item.
switches the set on from standby.
F / G (Volume Up/Down)
adjusts the volume.
adjusts menu settings.
OK
accepts your selection or displays the
current mode.
I/II
Selects the language during dual language broadcast.
Selects the sound output.
OK
VOL
VOL
PR
NUMBER buttons
1
2
3
4
5
6
7
8
9
PSM
0
SSM
Q.VIEW TEXT
SLEEP
REVEAL
?
MODE
M
SIZE
MIX
UPDATE
TIME
HOLD
INDEX
i
SSM
To select the sound appropriate to
your viewing programme.
SLEEP
Sets the sleep timer.
TEXT
These buttons are used for teletext.
For further details, see the ‘Teletext’
section.
COLOURED BUTTONS
These buttons are used for teletext (only
TELETEXT models) or programme edit.
Installing Batteries
• Open the battery compartment cover on the back side and
insert the batteries with correct polarity.
• Install two 1.5V alkaline batteries of AAA type. Don’t mix used
batteries with new batteries.
6 PLASMA TV
Introduction
ENGLISH
Location and Function of Controls
<Front Panel Controls>
42PX3RV series
TV/AV
1
2
TV/AV
MENU
4
5
3
1.
Remote Control Sensor
2.
Power Indicator
Illuminates red in standby mode, Illuminates green when the
set is turned on.
3. Power Button
Switches the set on from standby or off to standby.
4.
TV/AV Button
Selects the TV, AV, Component, RGB or HDMI modes.
Switches the set on from standby.
MENU
VOL
OK
6
OK
VOL
PR
PR
7
5.
MENU
Displays on screen menus one by one.
Exits the current menu.
Memorizes menu changes.
6.
OK
Accepts your selection or displays the current mode.
7.
D / E (Programme Up/Down)
Selects a programme or a menu item.
Switches the set on from standby.
F / G (Volume Up/Down)
Adjusts the volume.
Adjusts menu settings.
42PX2RV series
ON/OFF
TV/AV
Main Power Button
Remote Control Sensor
MENU
VOL
PR
MENU
Displays on screen menus one by one.
Exits the current menu.
Memorizes menu changes.
Power Standby Indicator
Illuminates red in standby TV/AV Button
mode, Illuminates green Selects the TV, AV, Component,
when the set is turned on RGB or HDMI modes. If OSD is
displayed, selects menu item.
D / E (Programme Up/Down)
selects a programme or a menu item.
switches the set on from standby.
F / G (Volume Up/Down)
adjusts the volume.
adjusts menu settings.
Owner’s Manual 7
Introduction
Location and Function of Controls
- Shown is a simplified representation of the set.
- What is shown here may be somewhat different from your set.
<Back Panel>
VIDEO
S-VIDEO
AV5
R AUDIO L/MONO
9
AUDIO
COMPONENT
L
R
AC INPUT
L
S-VIDEO
HDMI
AUDIO INPUT
RGB INPUT
VIDEO
(MONO)
R
AUDIO
AV1
L
REMOTE
CONTROL
Antenna
AUDIO
AV4
R
AV2
VARIABLE
VARIABLE
AUDIO OUT
RS-232C INPUT
(CONTROL/SERVICE)
AV3
1
2
3
4
1. HDMI(DVI VIDEO) / AUDIO INPUT / RGB INPUT
Connect the monitor output socket of the PERSONAL COMPUTER, DVD or STB to this socket.
Note: If you want to use RGB/DVI audio, we strongly recommend that you use the cable that has a core, or the EMI Filter
core along with separate cable.
2. REMOTE CONTROL
3. RS-232C INPUT(CONTROL/SERVICE) PORT
Connect to the RS-232C port on a PC.
4. COMPONENT INPUT
Connect DVD video outputs to Y, PB, PR of COMPONENT
INPUT and audio outputs to Audio sockets of AUDIO INPUT.
AUDIO/VIDEO IN SOCKETS (AV4)
Connect the audio/video out sockets of external equipment to
these sockets.
S-VIDEO/AUDIO IN SOCKETS
Connect the S-VIDEO out socket of an VCR to the S-VIDEO
socket.
Connect the audio out sockets of the VCR to the audio sockets as in AV4.
8 PLASMA TV
5
6
7
8
5. VARIABLE AUDIO OUTPUT
6. EURO SCART SOCKET
Connect the euro scart socket of the VCR to these sockets.
Note:
a. If you want to use the EURO scart cable, you have to use
the signal shielded Euro scart cable.
b. If the S-VIDEO(Y/C) signal is received through the Euro scart
socket 2 (AV 2), you must change to the S-Video 2 (Y/C) mode.
7. ANTENNA INPUT
8. POWER CORD SOCKET
This Monitor operates on AC power. The voltage is indicated
on the Specifications page. Never attempt to operate the set
on DC power.
9. AUDIO/VIDEO INPUT (AV5)
S-VIDEO/AUDIO IN SOCKETS
Installation
ENGLISH
External Equipment Viewing Setups
Antenna Connection
- Be careful not to bend the bronze wire when connecting to an antenna port.
Apartments
(connecting to wall antenna socket)
Antenna
wall antenna socket
< Back panel of the set >
RF coaxial wire (75 ohms)
VHF antenna
UHF antenna
outdoor antenna
Private house
(connecting to wall outdoor antenna)
Watching VCR
- When connecting the set to external equipment, match the colours of connecting ports (Video - yellow, Audio (L) - white, Audio
(R) -red).
- Connect the VIDEO INPUT socket (yellow) of external equipment to the VIDEO INPUT on the set.
- If you have a mono VCR, connect the audio cable from the VCR to the AUDIO (L/MONO) input on the set.
- If you connect an S-VIDEO VCR to the S-VIDEO input, the picture quality is improved; compared to connecting a regular VCR
to the Video input.
Or, connect the Euro scart socket of the VCR to the Euro scart socket of the set.
- Use the orbiter function to Avoid having a fixed image remain on the screen for a long period of time. Typically a frozen still picture from a VCR. (Refer to p. 27)
If a 4:3 picture format is used, the fixed image may remain visible on the screen.
- To avoid picture noise (interference), leave an adequate distance between the VCR and set.
< Back panel of the set >
Watching TV programmes
- Turn the set on and select the programme you
want.
COMPONENT
AUDIO
L
Watching VCR
1. Use the TV/AV button on the remote control to
select AV1, AV2, S-Video2, AV3, AV4 or AV5.
- If both S-VIDEO and VIDEO sockets have been
connected to the S-VHS VCR simultaneously,
only the S-VIDEO can be received.
2. Insert a video tape into the VCR and press the
PLAY button on the VCR.
(See VCR owner’s manual)
L
S-VIDEO
RGB INPUT
VIDEO
R
(MONO)
R
AUDIO
AV1
L
RS-232C INPUT
Antenna
AUDIO
AV4
R
AV2
VARIABLE
V
ARIABLE
AUDIO OUT
(CONTROL/SERVICE)
AV3
< VCR >
Owner’s Manual 9
Installation
External Equipment Viewing Setups
Watching Cable TV
- After subscribing for a local cable TV station and installing a converter you can watch cable TV.
- For further information of cable TV, contact the local cable TV station.
< Back panel of the set >
L
L
S-VIDEO
NPUT
To watch cable TV
AUDIO
COMPONENT
VIDEO
1. Use the TV/AV button on the remote control to
select AV1, AV2, S-Video2, AV3, AV4 or AV5.
- If both S-VIDEO and VIDEO sockets have been
connected to the Cable box simultaneously, only
the S-VIDEO can be received.
2. Select your desired channel with the remote
control for cable box.
R
(MONO)
R
AUDIO
AV1
Antenna
AUDIO
AV4
L
R
AV2
VARIABLE
VARIABLE
AUDIO OUT
C INPUT
/SERVICE)
AV3
< Cable box >
Watching external AV source
- When connecting the set to an external source, match the colours of AUDIO/VIDEO input jacks on the set with the output jacks
on the audio/video equipment: Video = yellow, Audio (Left) = white, Audio (Right) = red.
Or, connect the Euro scart socket of the VCR to the Euro scart socket of the set.
How to use
1. Use the TV/AV button on the remote control to
select AV1, AV2, S-Video2, AV3, AV4 or AV5.
2. Operate the corresponding external equipment.
See external equipment operating guide.
< Back panel of the set >
AUDIO
COMPONENT
L
L
S-VIDEO
PUT
VIDEO
R
(MONO)
R
AUDIO
AV1
L
INPUT
Antenna
AUDIO
AV4
R
VARIABLE
VARIABLE
AUDIO OUT
AV2
ERVICE)
AV3
Camcorder
Video game set
10 PLASMA TV
R
AUDIO
L
VIDEO
ENGLISH
Installation
Watching DVD
How to connect
Connect DVD video outputs to Y, PB, PR of COMPONENT INPUT and audio outputs to Audio sockets of
AUDIO INPUT.
How to use
1. Turn on the DVD player, and insert a DVD.
2. Use TV/AV or MULTIMEDIA button on the remote
control to select Component.
Refer to the DVD player's manual for operating
instructions.
< Back panel of the set >
AUDIO
COMPONENT
L
R
L
S-VIDEO
HDMI
AUDIO INPUT
R
R
VIDEO
RGB INPUT
(MONO)
R
AUDIO
AV1
AUDIO
AV4
L
REMOTE
CONTROL
R
VARIABLE
V
ARIABLE
AUDIO OUT
RS-232C INPUT
AV2
(CONTROL/SERVICE)
AV3
• Component Input ports
You can get better picture quality if you connect
DVD player with component input ports as below.
R
Component ports of the
set
Video output ports
of DVD player
R
PR
Y
PB
Y
Y
Y
Y
Pr
Pb
B-Y R-Y
Cb Cr
PB PR
< DVD player >
Owner’s Manual 11
Installation
External Equipment Viewing Setups
Connecting PC
- To enjoy vivid picture and sound, connect a PC to the set.
- Avoid keeping a fixed image on the set’s screen for a long period of time. The fixed image may become permanently imprinted on
the screen; use a screen saver when possible.
- Connect PC to the RGB INPUT(PC INPUT) or HDMI INPUT(DIGITAL RGB INPUT) port of the set; change the resolution output
of PC accordingly.
- There might be noise according to some resolution, vertical pattern, contrast or brightness in PC mode. Change the PC mode into
another resolution or change the refresh rate into another rate or adjust the brightness and contrast on the menu until the picture
is clean. If the refresh rate of the PC graphic card can not be changed, change the PC graphic card or consult it to the manufacturer of the PC graphic card.
- The synchronization input waveform for Horizontal and Vertical frequencies are separate.
Setup Instructions to Connect a PC to your set
- We recommend using 1024x768, 60Hz for the PC mode, they provide the best picture quality.
In 42PX3RV / 42PX2RV series, we recommend using 640x480, 60Hz for the PC mode, they provide the best picture quality.
- If the resolution of PC is over UXGA, there will be no picture on the set.
- Connect the signal cable from the monitor output port of the PC to the RGB INPUT port of the set or the signal cable from the
HDMI output port of the PC to the HDMI INPUT port on the set.
- Connect the audio cable from the PC to the Audio input on the set. (Audio cables are not included with the set).
- If using a sound card, adjust PC sound as required.
- This set uses a VESA Plug and Play Solution. The set provides EDID data to the PC system with a DDC protocol. The PC adjusts
automatically to use this set.
- DDC protocol is preset for RGB (Analog RGB), HDMI (Digital RGB) mode.
- If required, adjust the settings for Plug and Play functionally.
- If graphics card on the PC does not output analog and digital RGB simultaneously, connect only one of RGB INPUT or HDMI
INPUT to display the PC on the set.
If graphic card on the PC does output analog and digital RGB simultaneously, set the set to either RGB or HDMI ; (the other mode
is set to Plug and Play automatically by the set.)
- DOS mode may not work depending on video card if you use a HDMI to DVI cable.
- When you use too long RGB-PC cable, there might be a noise on the screen. We recommend using under 5m of the cable. It provides the best picture quality.
< Back panel of the set >
COMPONENT
AUDIO
L
L
S-VIDEO
HDMI
AUDIO INPUT
RGB INPUT
VIDEO
R
(MONO)
R
AUDIO
AV1
AUDIO
AV4
L
REMOTE
CONTROL
RS-232C INPUT
R
VARIABLE
VARIABLE
AUDIO OUT
AV2
(CONTROL/SERVICE)
AV3
12 PLASMA TV
PC Setup
1. Turn on the PC and apply power to the set.
2. Turn on the display by pressing the POWER button on
the set’s remote control.
3. Use the TV/AV or MULTIMEDIA button on the remote
control to select the RGB or HDMI input source.
4. Set the resolution output of the PC to SXGA or under
(1280 x 1024, 60Hz). (Refer to p. 13)
Installation
RGB / HDMI mode
Resolution
640x350
ENGLISH
Displayable Monitor Specification
RGB / HDMI mode
Horizontal
Vertical
Frequency(KHz) Frequency(Hz)
31.468
70.09
31.469
70.08
37.927
85.03
59.94
31.469
59.94
35.000
66.66
35.000
66.66
37.861
72.80
37.861
72.80
37.500
75.00
37.500
75.00
43.269
85.00
43.269
85.00
31.500
60.00
31.500
60.00
37.799
70.00
37.799
70.00
39.375
75.00
39.375
75.00
31.500
60.00
31.500
60.00
37.799
70.00
37.799
70.00
39.375
75.00
39.375
75.00
35.156
56.25
35.156
56.25 (RGB)
37.879
60.31
37.879
60.31
48.077
72.18
48.077
72.18
46.875
75.00
46.875
75.00
53.674
85.06
53.674
85.06
49.725
74.55
49.725
74.55
48.363
60.00
48.363
60.00
56.476
70.06
56.476
70.06
60.023
75.02
60.023
75.02
68.677
85.00
68.677
85.00
54.348
60.05
47.700
60.00
63.995
70.01
59.625
75.02
67.500
75.00
68.500
85.00
1152x870
68.681
75.06
47.700
60.00
1280x960
60.023
60.02
59.625
75.02
1280x1024
63.981
60.02
69.500
85.00
54.348
60.05
63.995
70.01
67.500
75.00
77.487
85.00
68.681
75.06
47.693
60.00
60.091
75.00
848x480
852x480
800x600
832x624
1024x768
1152x864
42PX3RV series
42PX2RV series
31.469
70.08
37.927
85.03
31.469
640x350
85.08
640x480
85.08
Horizontal
Vertical
Frequency(KHz) Frequency(Hz)
31.468
70.09
37.861
720x400
37.861
Resolution
720x400
640x480
848x480
852x480
800x600
832x624
1024x768
1360x768
1366x768
1152x864
1152x870
1280x768
68.504
85.00
1280x960
60.023
60.02
1280x1024
63.981
60.02
50PX3R series
Owner’s Manual 13
Installation
-
HDMITM, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing.
This set can receive the High-Definition Multimedia Interface (HDMI) or Input of Digital Visual Interface(DVI).
This set supports HDCP (High-bandwidth Digital Contents Protection) Protocol for the set (480p, 720p, 1080i) modes.
When you connect to HDMI/DVI Source devices (DVD Player, STB or PC) that support AUTO HDMI/DVI Plug & Play, this sets
the HDMI/DVI source devices automatically.(640 x 480p) (or 50PX3R series: 1280 x 720p).
Afer reading HDMI/DVI source devices, using Display Data Channel (DDC) Protocol, Extended Display Identification Data
(EDID) stored in the set is used.
If HDMI/DVI Source devices do not support AUTO HDMI/DVI, the resolution is set manually.
- To get the best picture quality, adjust the DVD Player or Set Top Box output resolution to 640 x 480p (or 50PX3R series: 1280 x 720p).
- To get the best picture quality, adjust the PC graphics card to 640 x 480 (or 50PX3R series: 1024 x 768), 60Hz.
- When Source Devices have DVI Output Connector, you must connect audio with separated cable.(Refer to <How to connect>)
How to connect
1. When Source Devices (DVD Player or Set Top Box) support HDMI.
- If Source Devices have HDMI Output Connector, Source Devices connect to the set with HDMI Cable .(not supplied with the product).
- If Source Devices support Auto HDMI, automatically, Source Devices divert output resolution in 640x480p (or 50PX3R series:
1280 x 720p). But if not, resolution divert Manually Setting for reference Manual of Source Devices.
- To get the best picture quality, adjust the DVD Player or Set Top Box output resolution to 640x480p (or 50PX3R series: 1280 x
720p).
- Because HDMI sends Digital Video and Audio with one cable, there is no need for Audio Cable when using HDMI Cable.
2. When Source Devices (DVD Player or Set Top Box) supports DVI.
- If Source Devices have DVI Output Connector, Source Devices connect to the set with HDMI to DVI Cable (not supplied with the
product).
- If Source Devices support Auto DVI, automatically, Source Devices divert output resolution in 640x480p (or 50PX3R series: 1280
x 720p). But if not, resolution divert Manually Setting for reference Manual of Source Devices.
- To get the best picture quality, adjust the DVD Player or Set Top Box output resolution to 640x480p (or 50PX3R series: 1280 x
720p).
- In this case, Audio use other cable. When Source Devices have Analog Audio Output Connector, RGB/DVI Audio Input of the set
connect to Audio Cable (not supplied with the product). And then you can listen to normal Audio.
3.
-
When PC supports DVI.
If PC has a DVI Output Connector, Source Devices connect to the set with HDMI to DVI Cable (not supplied with the product).
To get the best picture quality, adjust the PC graphics card to 640x480 (or 50PX3R series: 1024 x 768), 60Hz.
Use the the set’s HDMI/DVI (VIDEO) for video connections, depending on your PC connector.
If the graphics card on the PC does not output analog RGB and DVI simultaneously, connect only one of either RGB Input or
HDMI/DVI Input to display the PC on the set.
- If the graphics card on the PC does output analog RGB and DVI simultaneously, the set to either RGB Input or HDMI/DVI Input;
(the other mode is set to Plug and Play automatically by the set.)
- Then, make the corresponding audio connections. If using a sound card, adjust the PC sound as required.
- In this case, Audio use other cable. When PC (or sound card of PC) have Analog Audio Output Connector, RGB/DVI Audio Input
of the set connect to Analog Audio Cable (not supplied with the product). And then you can listen to normal Audio.
14 PLASMA TV
Installation
ENGLISH
Reference
Cable sample
HDMI Cable
(not supplied with the product)
Analog Audio Cable (RCA type)
(not supplied with the product)
HDMI to DVI Cable
(not supplied with the product)
Analog Audio Cable (Stereo to RCA type)
(not supplied with the product)
How to use
1.
2.
3.
4.
Connect the HDMI/DVI Source Devices(DVD Player or Set Top Box or PC) and the set.
Turn on the display by pressing the POWER button on the set and HDMI/DVI Source Devices remote control.
Select HDMI/DVI Input source in Main Input option of PIP/DW menu.
Check the image on your set. There may be noise associated with the resolution, vertical pattern, contrast or brightness in
HDMI/DVI Source Devices. If noise is present, change the HDMI/DVI Source Devices to another resolution, change the refresh
rate or adjust the brightness and contrast on the menu until the picture is clear. If the refresh rate of the PC graphics card can not
changed, change the PC graphics card or consult the manufacturer of the PC graphics card.
Notes:
- Depending on the graphics card, DOS mode may not work if you use a HDMI to DVI Cable.
- Avoid keeping a fixed image on the set screen for a long period of time. The fixed image may become permanently imprinted on
the screen. Use the Orbiter screen saver when possible.
- When Source Devices connected HDMI/DVI Input, output PC Resolution(VGA, SVGA, XGA), Position, Size may not fit to Screen.
As shown the lower picture, press the MENU button to adjust the screen Position of the set and contact an PC graphics card service center.
- When Source Devices connected HDMI/DVI Input output the set Resolution(480p, 720p, 1080i), the set Display fit EIA/CEA-861B Specification to Screen. If not, refer to the Manual of HDMI/DVI Source Devices or contact your service center.
- In case of HDMI/DVI Source Devices are not connected, Cable or poor cable connection, "No Signal" OSD display in HDMI/DVI
Input. And In case of Video Resolution not supported when output is HDMI/DVI Source Devices, "No Signal" OSD display. Refer
to the Manual of HDMI/DVI Source Devices or contact your service center.
Owner’s Manual 15
Installation
Accessories
MUTE
POWER
TV/AV MULTIMEDIA I/II
LIST
ARC
MENU
PR
OK
VOL
VOL
PR
LG TV
1
2
4
5
3
6
7
8
9
PSM
0
SSM
Q.VIEW TEXT
SLEEP
REVEAL
?
MODE
M
SIZE
MIX
UPDATE
TIME
HOLD
INDEX
i
AS mark
Owner’s Manual
Remote Control handset
2-Eye Bolts
Power Cord
2-Wall brackets
1.5V
1.5V
Alkaline batteries
Fixing the set assembly to the wall to protect the set tumbling
- Secure the set assembly by fixing it to a wall by using the Eye Bolts/Wall brackets.
• If the set is mounted on a desk top, insert the 2 Eye-Bolts and tighten them
securely in the upper holes as shown.
Insert the 2 Eye Bolts and tighten securely, in the holes on the bracket.
Install the wall brackets on the wall with 2 bolts, (not supplied with the product),
as shown.
Match the height of the Eye Bolts and the wall brackets.
Check to be sure the brackets are tightened securely.
• Secure the set assembly to the wall with strong strings or wound wire cables,
(not supplied with the product), as shown.
Optional Extras
-
40
42
-
Optional extras can be changed or modified for quality improvement. Without any notification new optional extras can be
added.
Contract your dealer for buying these items.
40
50
16 PLASMA TV
42
Tilt wall mounting bracket
Ceiling mounting bracket
Video cables
Audio cables
Installation
ENGLISH
Installation Options
• The set can be installed in different ways such as on a wall, or on a desktop etc.
• Install this set only in a location where adequate ventilation is available.
Wall Mount: Horizontal Installation
Desktop Pedestal Installation
TV/AV
MENU
OK
VOL
PR
TV/AV
• The set can be installed on a wall as shown above.
(For further information, refer to the optional ‘Wall
Mounting Bracket Installation and Setup Guide’.)
To Mount on a Wall
Wall mount minimum allowable clearances for adequate ventilation.
MENU
OK
VOL
PR
• The set can be mounted on a desk as shown above.
To Install on a Desktop
Pedestal mount minimum allowable clearances for
adequate ventilation.
10cm
3cm
10cm
10cm
TV/AV
TV/AV
MENU
OK
VOL
MENU
OK
VOL
PR
PR
10cm
Owner’s Manual 17
Operation
Turning on the Set
42PX3RV series
- When using the remote control, aim it at its sensor on the set.
Turning on the set just after installation
1. Connect power cord correctly, the set is switched to standby mode.
2. Press the r / I, TV/AV or PR D / E button on the set or press the POWER, TV/AV, MULTIMEDIA, D / E or NUMBER
buttons on the remote control and then the set will switch on.
Turning on the set (power cord is still connected)
If the set was turned off with the remote control power button and the r / I button on the set
• Press the r / I, TV/AV or PR D / E button on the set or press the POWER, TV/AV, MULTIMEDIA, D / E or NUMBER
button on the remote control to turn the set on.
42PX2RV series
- When using the remote control, aim it at its sensor on the set.
Turning on the set just after installation
1. Connect power cord correctly.
2. Press the
ON/OFF button on the set. At this moment, the set is switched to standby mode. Press the TV/AV or
PR D / E button on the set or press the POWER, TV/AV, MULTIMEDIA, D / E or NUMBER buttons on the remote
control and then the set will switch on.
Turning on the set (power cord is still connected)
1. If the set was turned off with the
• Press the
ON/OFF button on the set
ON/OFF button on the set to turn the set on.
2. If the set was turned off with the remote control and the
ON/OFF button on the set
• Press the
ON/OFF button on the set and then press the TV/AV or PR D / E button on the set or press the
POWER, TV/AV, MULTIMEDIA, D / E or NUMBER button on the remote control to turn the set on.
On-Screen Menu Language Selection (option)
- The menus can be shown on the screen in the selected language. First select your language.
1. Press the MENU button and then use
2. Press the G button and then use D /
E
D
/
E
button to select the SPECIAL menu.
button to select Language.
3. Press the G button and then use D / E button to select your desired language.
From this point on, the on-screen menus will be shown in the language of your choice.
4. Repeatedly press the MENU button to return to normal TV viewing.
18 PLASMA TV
Operation
ENGLISH
Channel Menu Options
Auto Programme Tuning
- All stations that can be received are stored by this method. It is recommended that you use auto programme during
installation of this set.
1. Press the MENU button and then use D / E button to select the STATION menu.
2. Press the G button and then D / E button to select Auto programme.
3. Press the G button to select System. Select a TV system with the F / G button;
L : SECAM L/L’ (option)
BG : PAL B/G, SECAM B/G (Europe / East Europe / Asia / New Zealand / M.East / Africa
/Australia)
I
: PAL I/II (U.K. / Ireland / Hong Kong / South Africa)
DK : PAL D/K, SECAM D/K (East Europe / China / Africa / CIS)
M : (USA / Korea / Philippines) (option)
4. Press the E button to select Storage from. Select the beginning programme number
with the F / G button or NUMBER buttons on the Storage from menu.
5. Press the E button to select Start.
6. Press the G button to begin auto programming.
All receivable stations are stored.
STATION
PICTURE
Auto programme
programme G
Auto
Manual programme
Programme edit
Favourite programme
System
BG
Storage from
2
Start
SOUND
TIME
SPECIAL
SCREEN
Menu Prev.
Note : In some models, the station name is stored for stations which broadcast VPS
(Video Programme Service), PDC (Programme Delivery Control) or TELETEXT data. If
no station name can be assigned to a station, the channel number is assigned and
stored as C (V/UHF 01-69) or S (Cable 01-47), followed by a number.
To stop auto programming, press the MENU button.
When auto programming is completed, the Programme edit menu appears on the
screen. See the ‘Programme edit’ section to edit the stored programme.
Manual Programme Tuning
- Manual programme lets you manually tune and arrange the stations in whatever order you desire. Also you can
assign a station name with five characters to each programme number.
1. Press the MENU button and then use D / E button to select the STATION menu.
2. Press the G button and then D / E button to select Manual programme.
3. Press the G button to select Storage. Select the desired programme number with the
F / G button or NUMBER buttons on the Storage menu.
4. Press the E button to select System. Select a TV system with the F / G button;
L : SECAM L/L’ (option)
BG : PAL B/G, SECAM B/G (Europe / East Europe / Asia / New Zealand / M.East / Africa
/Australia)
I
: PAL I/II (U.K. / Ireland / Hong Kong / South Africa)
DK : PAL D/K, SECAM D/K (East Europe / China / Africa / CIS)
M : (USA / Korea / Philippines) (option)
5. Press the E button to select Band. Press the F / G button to select V/UHF or Cable
as required.
6. Press the E button to select Channel. You can select the desired channel number with
the F / G button or NUMBER buttons. If possible, select the channel number directly with
the number buttons.
7. Press the E button to select Search. Press the F / G button to commence searching. If
a station is found the search will stop.
8. Press the OK button to store it.
9. To store another station, repeat steps 3 to 8.
STATION
Auto programme
Manual programme
Manual
programme G
PICTURE
Programme edit
Favourite programme
SOUND
Storage
2
System
BG
Band
V/UHF
Channel
1
Fine
TIME
Search
Name
SPECIAL
C
SCREEN
Menu Prev.
Booster
01
Off
Owner’s Manual 19
Operation
Channel Menu Options
Fine Tuning
- Normally fine tuning is only necessary if reception is poor.
1.
2.
3.
4.
Repeat the ‘Manual programme tuning’ steps 1 to 2.
Press the G button and then D / E button to select Fine.
Press the F / G button to fine tune for the best picture and sound.
Press the OK button.
The finely tuned programme will be indicated by a yellow number during programme
selection.
5. Repeatedly press the MENU button to return to normal TV viewing.
STATION
PICTURE
Storage
2
System
BG
Band
V/UHF
1
Channel
SOUND
Fine
TIME
Search
Name
SPECIAL
C
Booster
SCREEN
Assigning a Station Name
STATION
1. Repeat the ‘Manual programme tuning’ steps 1 to 2.
2. Press the G button and then D / E button to select Name.
3. Press the G button to display the Name menu.
4. Press the D button. You can use a blank, +, -, the alphabet A to Z and the numeric 0 to
9.
With the E button you can select in the opposite direction.
5. Select the next position by pressing the G button and then make your choice of the second character, and so on.
6. Press the OK button in twice.
7. Repeatedly press the MENU button to return to normal TV viewing.
Auto programme
Manual programme
Manual
programme
Programme edit
Favourite programme
PICTURE
01
Off
Store
Auto programme
Manual programme
Manual
programme
Programme edit
Favourite programme
Storage
2
System
BG
Band
V/UHF
1
Channel
SOUND
Fine
TIME
Search
Name
SPECIAL
C
Booster
SCREEN
01
Off
Store
Booster (option)
In some models, Booster is an optional function. Only a set with Booster can perform this function.
If the reception is poor at the fringe area of TV signal, select Booster to On.
1.
2.
3.
4.
5.
Repeat the ‘Manual programme tuning’ steps 1 to 2.
Press the G button and then D / E button to select Booster.
Press the F / G button to select On or Off.
Press the OK button.
Repeatedly press the MENU button to return to normal TV viewing.
STATION
Auto programme
Manual programme
Manual
programme
PICTURE
Programme edit
Favourite programme
SOUND
Storage
2
System
BG
Band
1
Fine
TIME
Search
Name
C
SPECIAL
Booster
SCREEN
20 PLASMA TV
V/UHF
Channel
Store
01
F G Off
ENGLISH
Operation
Programme Edit
- This function enables you to delete or skip the stored programmes. Also you can move some stations to other programme numbers or copy a blank station data into the selected programme number.
1. Press the MENU button and then use D / E button to select the STATION menu.
2. Press the G button and then D / E button to select Programme edit.
3. Press the G button to display the Programme edit menu.
CHANNEL
Programme
edit
0
1
2
3
4
Deleting a programme
1. Select a programme to be deleted with the D / E or F / G button.
2. Press the RED button twice.
The selected programme is deleted, all the following programmes are shifted up one
position.
----BLN 2
C 01
C 04
C 05
Delete
Move
5
6
7
8
9
C
C
C
S
S
05
07
55
27
29
Copy
Skip
Menu Prev.
Copying a programme
1. Select a programme to be copied with the D / E or F / G button.
2. Press the GREEN button.
All the following programmes are shifted down one position.
Moving a programme
1. Select a programme to be moved with the D / E or F / G button.
2. Press the YELLOW button.
3. Move the programme to the desired programme number with the
4. Press the YELLOW button again to release this function.
D /E
or
F /G
button.
Skipping a programme number
1. Select a programme number to be skipped with the D / E or F / G button.
2. Press the BLUE button. The skipped programme turns to blue.
3. Press the BLUE button again to release the skipped programme.
When a programme number is skipped it means that you will be unable to select it using
the D / E button during normal TV viewing. If you want to select the skipped programme,
directly enter the programme number with the NUMBER buttons or select it in the programme edit or table menu.
Favourite Programme
- This function lets you select your favourite programmes directly.
1.
2.
3.
4.
5.
6.
Press the MENU button and then use D / E button to select the STATION menu.
Press the G button and then D / E button to select Favourite programme.
Press the G button and then D / E button to select On.
Press the G button to display the Favourite programme menu.
Press the D / E button to select -- -----.
Select a desired programme with the F / G button or NUMBER buttons. Any number
under 10 is entered with a numeric ‘0’ (or ‘00’) in front of it, i.e. ‘05’ (or ‘005’) for 5.
7. To store another programme, repeat steps 5 to 6.
You can store up to 8 programmes.
8. Press the OK button.
9. Repeatedly press the MENU button to return to normal TV viewing.
STATION
PICTURE
Auto programme
Manual programme
Programme edit
Favourite programme
programme
Favourite
On
Off
0 BLN 2
--- -- ---
SOUND
--- -- ----- -- ---
TIME
--- -- ----- -- ---
SPECIAL
--- -- ----- -- ---
SCREEN
Prev.
Repeatedly press the Q.VIEW button to select stored favorite programmes.
Calling up the Programme Table
- You can check the programmes stored in the memory by displaying the programme table.
Displaying programme table
Press the LIST button to display the Programme table menu.
The programme table appears on the screen.
•
•
You may find some blue highlighted programmes shown. They have been set up in the
programme edit mode.
Some programmes with the channel number shown in the programme table indicate
there is no station name assigned.
0
1
2
3
4
----BLN 2
C 01
C 04
C 05
5
6
7
8
9
C
C
C
S
S
05
07
55
27
29
Selecting a programme in the programme table
Select a programme with the D / E or F / G button.
Then press the OK button.
The Plasma Display switches to the chosen programme number.
Paging through a programme table
There are 10 programme table pages in which contain 100 programmes.
Pressing the D / E or F / G button repeatedly turns the pages.
Press the LIST button to return to normal TV viewing.
Owner’s Manual 21
Operation
Picture Menu Options
PSM (Picture Status Memory)
- This function adjusts the set to the best picture appearance.
- When adjusting picture options (contrast, brightness, colour, sharpness and tint (NTSC AV only)) manually, PSM is
automatically changed to User.
1. Press the PSM button
• Each press of the PSM button changes the screen display as shown below.
Dynamic
Standard
Mild
User
• You can also select Dynamic, Standard, Mild or User in the PICTURE menu.
• Picture options Dynamic, Standard and Mild are preset and programmed for good picture quality at
the factory and cannot be changed.
CSM (Colour Status Memory)
- To initialize values (reset to default settings), select the Normal option.
1. Press the MENU button and then use
D /E
button to select the PICTURE menu.
STATION
2. Press the
G
button and then use D
/E
button to select CSM.
PICTURE
3. Press the
ture.
G
button and then use D
/E
button to select the desired colour tempera-
SOUND
TIME
4. Repeatedly press the MENU button to return to normal TV viewing.
SPECIAL
• Each press of
SCREEN
D
Cool
/
E
button changes the screen display as shown below.
Normal
Warm
PSM
CSM
ACM
Contrast
Brightness
Colour
Sharpness
G
Cool
Normal
Warm
100
60
50
50
User
Red
0
Green
0
Blue
0
Menu Prev.
User
Manual Colour Temperature Control
- You can adjust red, green, or blue to any colour temperature you prefer.
1. Press the MENU button and then use
2. Press the
G
button and then use
3. Press the
G
button and then use D
4. Press the
G
button and then use
D /E
D /E
/E
button to select the PICTURE menu.
STATION
PSM
CSM
button to select CSM.
PICTURE
button to select User.
SOUND
ACM
Contrast
Brightness
Colour
Sharpness
D / E / F / G button
to make appropriate adjustments.
5. Repeatedly press the MENU button to return to normal TV viewing.
TIME
G
Normal
Warm
100
60
50
50
User
SPECIAL
SCREEN
Cool
Red
0
Green
0
Blue
0
Menu Prev.
- You can enjoy the vivid and hi-definition picture with LG’s Excellent Digital Reality processor technology.
- It’s not available to use this function in RGB[PC], HDMI[PC] mode.
- When selecting picture options (Dynamic, Standard and Mild) in PICTURE menu, XD is automatically changed
to On.
1. Press the MENU button and then use
2. Press the
3. Press the
G
G
button and then use D
button and then use
D /E
/E
D /E
button to select the PICTURE menu.
button to select XD.
button to select On or Off.
4. Repeatedly press the MENU button to return to normal TV viewing.
STATION
PSM
CSM
G
PICTURE
SOUND
TIME
ACM
Contrast
Brightness
Colour
Sharpness
SPECIAL
SCREEN
22 PLASMA TV
Menu Prev.
100
60
50
50
On
Off
ENGLISH
Operation
sRGB
- When the set was connected to external equipment with sRGB function, It’s adjusted a colour difference to display
the equal image each other.
- This function works in the following mode:RGB[PC], HDMI[PC].
1. Press the MENU button and then use
2. Press the
G
button and then use D
3. Press the
G
button and then use
D /E
/E
D /E
button to select the PICTURE menu.
STATION
button to select sRGB.
PICTURE
button to select On or Off.
SOUND
4. Repeatedly press the MENU button to return to normal TV viewing.
PSM
CSM
sRGB
ACM
Contrast
Brightness
G
100
60
On
Off
TIME
SPECIAL
SCREEN
Menu Prev.
ACM (Active Colour Management)
- Adjust the ACM to select the desired skin colour option.
- This function works in the following mode:
TV, AV1, AV2, S-Video2, AV3, AV4, AV5 or COMPONENT, RGB[DTV], HDMI[DTV].
- It’s not available to use this function in XD Off mode.
1. Press the MENU button and then use
2. Press the
G
button and then use
3. Press the G button and then use
D
D /E
button to select the PICTURE menu.
/ E button to select ACM.
F / G button
to make appropriate adjustments.
4. Repeatedly press the MENU button to return to normal TV viewing.
STATION
PSM
CSM
PICTURE
ACM
Contrast
Brightness
Colour
Sharpness
SOUND
TIME
G
100
60
50
50
Fleshtone
0
Greentone
0
Bluetone
0
SPECIAL
SCREEN
Menu Prev.
Manual Picture Control
- You can adjust picture contrast, brightness, colour, sharpness and tint (NTSC AV only) to the levels you prefer.
- It’s not available to use colour, sharpness function in RGB[PC], HDMI[PC] mode.
- In the broadcasting system PAL/SECAM, the picture item Tint doesn’t work.
1. Press the MENU button and then use
button to select the PICTURE menu.
STATION
button to select the desired picture option.
PICTURE
D /E
2. Press the G button and then use
D /E
3. Press the G button and then use
F / G button
to make appropriate adjustments.
4. Repeatedly press the MENU button to return to normal TV viewing.
SOUND
TIME
PSM
CSM
ACM
Contrast
Contrast
Brightness
Colour
Sharpness
100
100 G
60
50
50
SPECIAL
SCREEN
Menu Prev.
Owner’s Manual 23
Operation
Sound Menu Options
SSM (Sound Status Memory)
- This function lets you enjoy the best sound without any special adjustment because the set automatically selects the
appropriate sound option based on the program content.
- When adjusting sound options (treble and bass) manually, SSM is automatically changed to User.
1. Press the SSM button.
2. Press the SSM button to select your desired sound.
SRS TSXT
Flat
Music
Movie
Sports
User
• You can also select SRS TSXT, Flat, Music, Movie, Sports or User in the SOUND menu.
• The sound SRS TSXT, Flat, Music, Movie and Sports are programmed for good sound reproduction at the factory
and cannot be changed.
R
-
TruSurround XT
is a trademark of SRS Labs, Inc.
- TruSurround XT technology is incorporated under license from SRS Labs, Inc.
BBE
- BBE High Definition Sound restores clarity and presence for better speech intelligibility and musical realism.
1. Press the MENU button and then use
D /E
button to select the SOUND menu.
STATION
2. Press the
G
button and then use
D /E
button to select BBE.
PICTURE
3. Press the
G
button and then use
D /E
button to select On or Off.
SOUND
4. Repeatedly press the MENU button to return to normal TV viewing.
SSM
BBE
BBE
AVL
Balance
Treble
Bass
TV Speaker
G
On
Off
G
On
Off
0
50
50
TIME
SPECIAL
Manufactured under license from BBE Sound, Inc.
SCREEN
Menu Prev.
AVL (Auto Volume Leveler)
- This feature maintains an equal volume level; even if you change channels.
1. Press the MENU button and then use
D /E
button to select the SOUND menu.
STATION
2. Press the
G
button and then use
D /E
button to select AVL.
PICTURE
3. Press the
G
button and then use
D /E
button to select On or Off.
SOUND
4. Repeatedly press the MENU button to return to normal TV viewing.
SSM
BBE
AVL
AVL
Balance
Treble
Bass
TV Speaker
0
50
50
TIME
SPECIAL
SCREEN
Menu Prev.
Adjusting Sound Control
1. Press the MENU button and then use D
/E
button to select the SOUND menu.
STATION
2. Press the G button and then use
D /E
button to select the desired sound item.
PICTURE
3. Press the
F /G
button to make appropriate adjustments.
SOUND
G
button and then use
4. Repeatedly press the MENU button to return to normal TV viewing.
SSM
BBE
AVL
Balance
Treble
Treble
Bass
TV Speaker
TIME
SPECIAL
Note : Treble, Bass or BBE aren’t suitable to use SRS TSXT.
24 PLASMA TV
SCREEN
Menu Prev.
0
50
50 G
50
ENGLISH
Operation
TV Speaker
- You can adjust internal speaker status.
- In COMPONENT, RGB[PC] and HDMI[PC] mode, TV speaker/variable audio can be output even though there is no
video signal.
- If you want to use your external hi-fi stereo system, turn off the internal speakers of the set.
1. Press the MENU button and then use
D /E
2. Press the
G
button and then use
D
3. Press the
G
button and then use
D /E
button to select the SOUND menu.
STATION
/ E button to select TV Speaker.
PICTURE
button to select On or Off.
SOUND
4. Repeatedly press the MENU button to return to normal TV viewing.
SSM
BBE
AVL
Balance
Treble
Bass
TV speaker
Speaker
TV
0
50
50
G
TIME
On
Off
SPECIAL
SCREEN
Menu Prev.
Stereo / Dual Reception
- When a programme is selected, the sound information for the station appears after the programme number and station name disappear.
On Screen Display
Press the I/II button to received broadcast state.
Broadcast
Mono
Stereo
Dual
On screen Display
MONO
STEREO
DUAL I
Mono Sound Selection
In stereo reception if the stereo signal is weak, you can switch to mono by pressing the
I/II button twice. In mono reception the depth of sound is improved. To switch back to
stereo, press the I/II button twice again.
Language Selection for Dual Language Broadcast
If a programme received in two languages (dual language), you can switch to DUAL I,
DUAL II or DUAL I + II by pressing the I/II button repeatedly.
• DUAL I sends the primary broadcast language to the loudspeakers.
• DUAL II sends the secondary broadcast language to the loudspeakers.
• DUAL I + II sends a separate language to each loudspeaker.
NICAM Reception (option)
- If your Plasma Display is equipped with the PDP Tuner for NICAM reception, the high quality NICAM (Near
Instantaneous Companding Audio Multiplex) digital sound can be received.
Sound output can be selected according to the type of received broadcast as follows by
pressing the I/II button repeatedly.
• When NICAM mono is received, you can select NICAM MONO or FM MONO.
• When NICAM stereo is received, you can select NICAM STEREO or FM MONO. If
the stereo signal is weak, switch to FM mono.
• When NICAM dual is received, you can select NICAM DUAL I, NICAM DUAL II,
NICAM DUAL I + II, or MONO. When FM mono is selected the display MONO
appears on the screen.
Sound output selection
In AV, Component, RGB or HDMI mode, you can select output sound for the left and right
loudspeakers.
Repeatedly press the I/II button to select the sound output.
• L+R : Audio signal from audio L input is sent to left loud-speaker and audio signal from
audio R input is sent to right loud-speaker.
• L+L : Audio signal from audio L input is sent to left and right loud-speakers.
• R+R : Audio signal from audio R input is sent to left and right loud-speakers.
Owner’s Manual 25
Operation
T ime Menu Options
Setting the Clock
- If current time setting is erased by a power failure or the set is unplugged, reset the clock.
1. Press the MENU button and then use
D
/
E
button to select the TIME menu.
STATION
2. Press the
G
button and then use
D
/ E button to select Clock.
3. Press the
G
button and then use
D
/
E
button to adjust the hour.
SOUND
4. Press the
G
button and then use
D
/
E
button to adjust the minute.
TIME
PICTURE
Clock
Clock
Off time
On time
Auto sleep
--
G
:
--
SPECIAL
5. Repeatedly press the MENU button to return to normal TV viewing.
SCREEN
Menu Prev.
Setting the On/Off Timer
- Timer function operates only if current time has been already set.
- Off Timer function overrides on Timer function if they are set to the same time.
- The set must be in standby mode for the On Timer to work.
1. Press the MENU button and then use
D
/
E
button to select the TIME menu.
2. Press the
G
button and then use
D
/ E button to select Off time or On time.
3. Press the
G
button and then use
D
/
E
STATION
PICTURE
button to select On.
G
button and then use
D
/
E
button to adjust the hour.
TIME
5. Press the
G
button and then use
D
/
E
button to adjust the minute.
SPECIAL
6. Only On time function; Press the
gramme number or volume level.
G
D
G
/
E
button to adjust pro-
SCREEN
On
Off
12
SOUND
4. Press the
button and then use
Clock
Off time
time
On time
Auto sleep
30
1
Menu Prev.
- To cancel Off/On time function
Press the D / E button to select Off in step 3.
- Two hours after the set is switched on by the on time function it will automatically switch back to standby mode
unless a button has been pressed.
Auto Sleep
- If there is no input signal, the monitor turn off automatically after 10 minutes.
D
/
E
button to select the TIME menu.
STATION
2. Press the G button and then use
D
/
E
button to select Auto sleep.
PICTURE
3. Press the G button and then use
D
/
E
button to select On or Off.
SOUND
4. Repeatedly press the MENU button to return to normal TV viewing.
Clock
Off time
On time
Autosleep
sleep
Auto
TIME
SPECIAL
SCREEN
Menu Prev.
Sleep Timer
- Sleep timer turns the set off at the preset time.
zz
- Press the SLEEP button to select the number of minutes. The display
--- Min will appear on the screen, followed by 10, 20, 30, 60, 90, 120, 180 and 240 minutes. The timer begins to count down from the number of minutes
selected.
a. To check the remaining sleep time, press the SLEEP button once.
b. To cancel the sleep time, repeatedly press the SLEEP button until the display
c. If you turn the set off after setting the sleep timer, the setting will be erased.
26 PLASMA TV
zz
--- Min
appears.
G
00
Programme
7. Repeatedly press the MENU button to return to normal TV viewing.
1. Press the MENU button and then use
:
Volume
On
Off
Operation
ENGLISH
Special Menu Options
Child Lock
- The set can be set up so that it can only be used with the remote control.
1. Press the MENU button and then
2. Press the
G
button and then
D
3. Press the G button and then D /
/
D
E
E
/
E
button to select the SPECIAL menu.
button to select Child lock.
button to select On or Off.
4. Repeatedly press the MENU button to return to normal TV viewing.
STATION
PICTURE
SOUND
Input
Language
Child lock
lock
Child
ISM Method
Low power
Set ID
Demo
G
On
Off
TIME
SPECIAL
SCREEN
Menu Prev.
- This set programmed to remember which option it was last set to even if you turn the set off.
- In Child lock ‘On’, if the set is turned off, press the TV/AV, PR D / E button on the set or POWER, TV/AV, MULTIMEDIA, D / E or NUMBER buttons on the remote control.
- With the Child lock On, the display ‘ Child lock on’ appears on the screen if any button on the front panel is
pressed while viewing the set.
ISM (Image Sticking Minimization) Method
- Frozen still picture from a PC/video game displayed on the screen for prolonged periods will result in an ghost
image remaining even when you change the image. Avoid allowing a fixed image to remain on the set's screen for
a long period of time.
1. Press the MENU button and then use
2. Press the
G
button and then
D /E
D /E
button to select the SPECIAL menu.
button to select ISM Method.
STATION
PICTURE
SOUND
3. Press the G button and then D / E button to select either Normal, White wash,
Orbiter or Inversion. If you unnecessary to set this function, set Normal.
Input
Language
Child lock
Method
ISM Method
Low power
Set ID
Demo
G
Normal
White wash
Orbiter
Inversion
TIME
SPECIAL
• White Wash :
White Wash removes permanent images from the screen.
Note: An excessive permanent image may be impossible to clear entirely with White
Wash.
• Orbiter :
Orbiter may help prevent ghost images. However, it is best not to allow any fixed
image to remain on the screen. To avoid a permanent image on the screen, the
screen will move every 2 minutes.
• Inversion :
This is the function to invert the panel colour of the screen. The panel colour is automatically inverted every 30 minutes.
SCREEN
Menu Prev.
4. Repeatedly press the MENU button to return to normal TV viewing.
Owner’s Manual 27
Operation
Special Menu Options
Low Power
- This is the function to reduce the power consumption of the set.
1. Press the MENU button and then use
2. Press the
G
button and then use
3. Press the
G
button and then use
D /E
button to select the SPECIAL menu.
STATION
D /E
button to select Low power.
PICTURE
D /E
button to select On or Off.
SOUND
Input
Language
Child lock
ISM Method
Lowpower
power
Low
G
Set ID
On
Off
Demo
4. Repeatedly press the MENU button to return to normal TV viewing.
TIME
SPECIAL
SCREEN
Menu Prev.
Demo
- Use it to see the difference between XD demo on and XD Demo off.
- It’s not available to use this function in RGB[PC], HDMI[PC] mode.
1. Press the MENU button and then use
D /E
2. Press the
G
button and then use
3. Press the
G
button to begin XD Demo.
D /E
button to select the SPECIAL menu.
button to select XD Demo.
4. To stop XD Demo, press the MENU button.
STATION
PICTURE
SOUND
Input
Language
Child lock
ISM Method
Low power
Set ID
Demo
Demo
TIME
SPECIAL
SCREEN
28 PLASMA TV
Menu Prev.
G
To start
Operation
ENGLISH
Screen Menu Options
Auto Configure
- Automatically adjusts picture position and minimizes image shaking.
- This function works in the following mode : RGB[PC].
1. Press the MENU button and then use
2. Press the
G
button and then use
D
D
E
button to select the SCREEN menu.
button to select Auto config..
E
/
/
3. Press the G button to start Auto config..
• When Auto config. has finished, Ok will be shown on screen.
• If the position of the image is still not correct, try Auto adjustment again.
STATION
PICTURE
SOUND
TIME
Auto config.
config.
Auto
Manual config.
VGA Mode
ARC
Zoom +/Position
Cinema
NR
Reset
G
To set
SPECIAL
4. If picture needs to be adjusted more after Auto adjustment in RGB[PC], you can adjust
the Manual Config..
SCREEN
Menu Prev.
5. Repeatedly press the MENU button to return to normal TV viewing.
- Although the image is still not correct, your set is functioning properly but needs further adjustment.
- The Auto config. functions don’t need to be run for HDMI mode.
Manual Configure
- If the picture isn’t clear after auto adjustment and especially that characters are still trembling, adjust the picture
phase manually.
- To correct the screen size, adjust Clock.
- This function works in the following mode : RGB[PC], RGB[DTV], COMPONENT (480p/576p/720p/1080i), HDMI
(480p/576p/720p/1080i).
- It’s not available to use Phase, Clock function in RGB[DTV], COMPONENT (480p/576p/720p/1080i), HDMI
(480p/576p/720p/1080i) mode.
1. Press the MENU button and then
2. Press the
G
button and then
D
/
3. Press the
G
button and then
D
/
D
E
E
/
E
button to select the SCREEN menu.
PICTURE
button to select Phase, Clock, H-Position or
SOUND
V-Position.
4. Press the
F
STATION
button to select Manual config..
TIME
/
G
button to make appropriate adjustments.
5. Repeatedly press the MENU button to return to normal TV viewing.
Auto config.
Manualconfig.
config.
Manual
VGA Mode
ARC
Zoom +/Position
Cinema
NR
Reset
G
Phase
0
Clock
0
H-Position
0
V-Position
0
SPECIAL
SCREEN
Menu Prev.
Selecting Wide VGA/XGA mode
- To see a normal picture, match the resolution of RGB mode and selection of VGA/XGA mode.
- In some models, it’s not available to selection of XGA mode.
- This function works in the following mode : RGB[PC].
1. Press the MENU button and then use
2. Press the
G
button and then use
button to select the SCREEN menu.
STATION
button to select VGA Mode (or XGA Mode).
PICTURE
button to select the desired VGA/XGA resolution.
SOUND
D /E
D /E
3. Press the G button and then use D
/E
4. Repeatedly press the MENU button to return to normal TV viewing.
TIME
Auto config.
Manual config.
Mode
VGA Mode
ARC
Zoom +/Position
Cinema
NR
Reset
G
640x480
848x480
852x480
SPECIAL
SCREEN
Menu Prev.
Owner’s Manual 29
Operation
Screen Menu Options
Setting Picture Format
- You can watch the screen in various picture formats; Spectacle, Full (option), Original, 4:3, 16:9 (Wide), 14:9 and
Zoom.
1. Press the MENU button and then use
2. Press the
G
button and then use
D
3. Press the G button and then use
Original, 4:3, 16:9, 14:9 or Zoom.
D
E
/
/
E
button to select the SCREEN menu.
button to select ARC.
D / E
button to select Spectacle, Full (option),
STATION
PICTURE
SOUND
TIME
• Spectacle
When your TV receives the wide screen signal, following selection will lead you to adjust
the picture horizontally, in non-linear proportion, to fill the entire screen.
Auto config.
Manual config.
VGA Mode
ARC
ARC
G
Zoom +/Position
Cinema
NR
Reset
Spectacle
Full
Original
4:3
16:9
14:9
Zoom
SPECIAL
SCREEN
Menu Prev.
• Full (option)
When your TV receives the wide screen signal, following selection will lead you to adjust
the picture horizontally or vertically, in a linear proportion, to fill the entire screen fully.
• Original
When your TV receives the wide screen signal, it will be automatically changed to the
picture format to be sent.
• 4:3
Following selection will lead you to view a picture with an original 4:3 aspect ratio, with
gray bars appearing at both the left and right sides.
• 16:9 (Wide)
Following selection will lead you to adjust the picture horizontally, in a linear proportion,
to fill the entire screen (useful for viewing 4:3 formatted DVDs).
• 14:9
You can enjoy the picture format of 14:9 or general TV programme through the 14:9
mode. The screen 14:9 is viewed just like that the screen 4:3 is magnified to the left /
right.
• Zoom
Following selection will lead you to view the picture without any alternation, while filling
the entire screen. However, the top and bottom portions of the picture will be cropped.
4. Repeatedly press the MENU button to return to normal TV viewing.
-
You can only select 4:3 and 16:9 (Wide) in RGB[PC], HDMI[PC] mode only.
You can only select 4:3, 16:9 (Wide) and Zoom in RGB[DTV], HDMI[DTV], Component [DTV] mode only.
You can only select Spectacle, Full (option), 4:3, 16:9 (Wide), 14:9 and Zoom in Component [480i/576i] mode only.
There might be uncomfortable in full mode. Then change into other mode.
Picture Size Zoom
- When enlarging or reducing the picture, the screen may be display unnatural picture.
1. Press the MENU button and then
D
2. Press the
G
button and then
D
/
E
3. Press the
G
button and then
F
/
G
/
E
button to select the SCREEN menu.
button to select Zoom +/-.
button to make appropriate adjustments.
4. Repeatedly press the MENU button to return to normal TV viewing.
STATION
PICTURE
SOUND
TIME
Auto config.
Manual config.
VGA Mode
ARC
Zoom +/+/Zoom
Position
Cinema
NR
Reset
SPECIAL
SCREEN
30 PLASMA TV
Menu Prev.
100
G
F
%
G
ENGLISH
Operation
Screen Position
- You can available to this function after adjusting Zoom +/-.
1. Press the MENU button and then
D
2. Press the
G
button and then
D
/
E
3. Press the
G
button and then
D
/
E
E
/
button to select the SCREEN menu.
button to select Position.
or
F
/
G
button to adjust the position.
4. Repeatedly press the MENU button to return to normal TV viewing.
STATION
PICTURE
SOUND
TIME
Auto config.
Manual config.
VGA Mode
ARC
Zoom +/Position
Position
D
G
F
G
E
Cinema
NR
Reset
SPECIAL
SCREEN
Menu Prev.
Cinema
- When you watch the movie, this function adjusts the set to the best picture appearance.
- This function works in the following mode:
TV, AV1, AV2, S-Video2, AV3, AV4, AV5 or COMPONENT 480i/576i.
1. Press the MENU button and then use
D /E
button to select the SCREEN menu.
2. Press the
G
button and then use
D
/
E
button to select Cinema.
PICTURE
3. Press the
G
button and then use
D
/
E
button to select On or Off.
SOUND
4. Repeatedly press the MENU button to return to normal TV viewing.
STATION
TIME
Auto config.
Manual config.
VGA Mode
ARC
Zoom +/Position
Cinema
Cinema
G
On
Off
G
3D NR
0
MPEG NR
0
NR
Reset
SPECIAL
SCREEN
Menu Prev.
NR (Noise Reduction)
- You can select 3D NR or MPEG NR to reduce the picture noise which may appear on the screen during watching
the TV.
- This function is not available for use in RGB[PC[, HDMI[PC] mode.
- 3D NR is not available for use in RGB, HDMI, Component[DTV] mode.
1. Press the MENU button and then use
D /E
2. Press the G button and then use
D /E
button to select NR.
PICTURE
3. Press the G button and then use
D /E
button to select 3D NR or MPEG NR.
SOUND
4. Press the
F
/
G
button to select the SCREEN menu.
button to make appropriate adjustments.
5. Repeatedly press the MENU button to return to normal TV viewing.
STATION
TIME
Auto config.
Manual config.
VGA Mode
ARC
Zoom +/Position
Cinema
NR
Reset
SPECIAL
SCREEN
Menu Prev.
Initializing (Reset to original factory value)
This function operates in current mode.
To initialize the adjusted value
1. Press the MENU button and then
2. Press the
G
button and then
3. Press the
G
button.
D
/
D
E
/
E
button to select the SCREEN menu.
button to select Reset.
• You can initialize Phase, Clock, H-Position, V-Position, Position, Zoom +/-.
STATION
PICTURE
SOUND
TIME
Auto config.
Manual config.
VGA Mode
ARC
Zoom +/Position
Cinema
NR
Reset
G
To set
SPECIAL
SCREEN
Menu Prev.
Owner’s Manual 31
Operation
Teletext (option)
- Teletext (or TOP text) is an optional function, therefore only the set with the teletext system can receive the teletext
broadcast.
- Teletext is a free service broadcast by most TV stations which gives up-to-the-minute information on news, weather,
television programmes, share prices and many other topics.
- The teletext decoder of this set can support the SIMPLE, TOP and FASTEXT systems. SIMPLE (standard teletext)
consists of a number of pages which are selected by directly entering the corresponding page number. TOP and FASTEXT are more modern methods allowing quick and easy selection of teletext information.
Switch on/off
Press the TEXT button to switch to teletext.
• The initial page or last page appears on the screen.
Two page numbers, TV station name, date and time are displayed on the screen headline. The first page number indicates your selection, while the second shows the current
page displayed.
Press the TEXT button to switch off teletext.
SIMPLE Text (option)
Page selection
1. Enter the desired page number as a three digit number with the NUMBER buttons. If
during selection you press a wrong number, you must complete the three digit number
and then reenter the correct page number.
2. The D / E button can also be used to select the preceding or following page.
Programming a colour button in LIST mode
If the TV is in SIMPLE text, TOP text or FASTEXT mode, press the
LIST mode.
M
button to switch to
Four teletext page numbers of your choice can be colour coded and easily selected by
pressing the corresponding coloured button on the remote control handset.
1. Press a coloured button.
2. Using the NUMBER buttons, select the page you wish to programme.
3. Press the OK button. The selected page is stored as the selected page number, blinking once to confirm this. From now on, you can select this page with the same coloured
button.
4. The three other coloured buttons are programmed in this way.
TOP Text (option)
The user guide displays four fields-red, green, yellow and blue at the bottom of the screen.
The yellow field denotes the next group and the blue field indicates the next block.
Block / group / page selection
1. With the blue button you can progress from block to block.
2. Use the yellow button to proceed to the next group with automatic overflow to the next
block.
3. With the green button you can proceed to the next existing page with automatic overflow to the next group. (Alternatively the D button can be used.)
4. The red button permits to return to previous selection. (Alternatively the E button can
be used.)
Direct page selection
Corresponding to the SIMPLE text mode, you can select a page by entering it as a three
digit number using the NUMBER buttons in TOP mode.
32 PLASMA TV
ENGLISH
Operation
FASTEXT
The teletext pages are colour coded along the bottom of the screen and are selected by
pressing the corresponding coloured button.
Page selection
1. Press the i button to select the index page.
2. You can select the pages which are colour coded along the bottom line with the same
coloured buttons.
3. Corresponding to the SIMPLE text mode, you can select a page by entering its three
digit page number with the NUMBER buttons in FASTEXT mode.
4. The D / E button can also be used to select the preceding or following page.
Special Teletext Functions
REVEAL
Press this button to display concealed information, such as solutions of riddles or
puzzles.
Press this button again to remove the information from the display.
SIZE
Selects double height text.
Press this button to enlarge the top half of the page.
Press this button again to enlarge the bottom half of the page.
Press this button again to return to the normal display.
UPDATE
Displays the TV picture on the screen while waiting for the new teletext page.
Press this button to view the updated teletext page.
HOLD
Stops the automatic page change which will occur if a teletext page consists of 2 or
more sub pages. The number of sub pages and the sub page displayed is, usually,
shown on the screen below the time. When this button is pressed the stop symbol
is displayed at the top left-hand corner of the screen and the automatic page
change is inhibited.
To continue press this button again.
MIX
Displays the teletext pages superimposed on the TV picture.
To switch the TV picture off press this button again.
TIME
This button has two functions:
a) When viewing a TV programme, press this button to display the time at the top
right hand corner of the screen. Press this button again to remove the display.
b) In teletext mode, press this button to select a sub page number. The sub page
number is displayed at the bottom of the screen. To hold or change the sub page,
press the RED/ GREEN or D / E buttons. Press this button again to exit this function.
Owner’s Manual 33
Miscellaneous
External Control Device Setup
- Connect the RS-232C input jack to an external control device (such as a computer or an A/V control system)
and control the set’s functions externally.
How to connect external control equipment
• Connect the serial port of the control device to the RS-232C jack on the Monitor back panel.
• RS-232C connection cables are not supplied with the set.
• The set remote control and front panel controls (except main power) will not be functional if the Monitor is controlled by a PC
computer or other external device.
< Back panel of the set >
AUDIO
COMPONENT
L
L
S-VIDEO
HDMI
RGB INPUT
AUDIO INPUT
VIDEO
R
(MONO)
R
AUDIO
AV1
AUDIO
AV4
L
VARIABLE
V
ARIABLE
AUDIO OUT
RS-232C INPUT
REMOTE
CONTROL
R
AV2
(CONTROL/SERVICE)
AV3
Type of connector; D-Sub 9-pin male
No.
1
2
3
4
5
6
7
8
9
1
Pin name
No connection
RXD (Receive data)
TXD (Transmit data)
DTR (DTE side ready)
GND
DSR (DCE side ready)
RTS (Ready to send)
CTS (Clear to send)
No Connection
5
9
6
RS-232C configurations
3-wire configuration
(Not standard)
7-wire configuration
(Standard RS-232C cable)
PC
PDP
2
3
5
4
6
7
8
3
2
5
6
4
8
7
D-Sub 9
D-Sub 9
RXD
TXD
GND
DTR
DSR
RTS
CTS
34 PLASMA TV
TXD
RXD
GND
DSR
DTR
CTS
RTS
RXD
TXD
GND
DTR
DSR
RTS
CTS
PC
PDP
2
3
5
4
6
7
8
3
2
5
4
6
7
8
D-Sub 9
D-Sub 9
TXD
RXD
GND
DTR
DSR
RTS
CTS
ENGLISH
Miscellaneous
Set ID
- Use this function to specify a set ID number.
- Refer to ‘Real Data Mapping 1’. See page 39.
1. Press the MENU button and then use the
2. Press the
button and then use
D /E
3. Press the G button and then use
monitor ID number.
F /G
G
D /E
button to select the SPECIAL menu.
button to select Set ID.
STATION
PICTURE
button to adjust Set ID to choose the desired
SOUND
Input
Language
Child lock
ISM Method
Low power
Set ID
G
1
Demo
TIME
• The adjustment range of Set ID is 1 ~ 99.
SPECIAL
4. Repeatedly press the MENU button to return to normal TV viewing.
SCREEN
MENU Prev.
Communication Parameters
• Baud rate : 9600 bps (UART)
• Data length : 8 bits
• Parity : None
* Use a crossed (reverse) cable.
• Stop bit : 1 bit
• Communication code : ASCII code
Command Reference List
COMMAND 1 COMMAND 2
DATA
(Hexadecimal)
01. Power
02. Input Select
03. Aspect Ratio
04. Screen Mute
05. Volume Mute
06. Volume Control
07. Contrast
08. Brightness
09. Colour
10. Tint (option)
11. Sharpness
12. OSD Select
13. Remote control lock mode
14. Treble
15. Bass
16. Balance
17. Colour Temperature (CSM)
18. Red Adjustment
19. Green Adjustment
20. Blue Adjustment
21. Abnormal Status
22. ISM Method
23. Low Power
24. Orbiter Time Setting
25. Orbiter Pixel Setting
26. Auto Configure
27. Programme selection
28. Key
29. Input select
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
j
j
j
j
j
m
m
x
a
b
c
d
e
f
g
h
i
j
k
l
m
r
s
t
u
v
w
$
z
p
q
r
s
u
a
c
b
0~1
0~9
Refer to p. 36
0~1
0~1
0 ~ 64
0 ~ 64
0 ~ 64
0 ~ 64
0 ~ 64
0 ~ 64
0~1
0~1
0 ~ 64
0 ~ 64
0 ~ 64
0~3
0 ~ 50
0 ~ 50
0 ~ 50
0~a
0~3
0~1
1 ~ FE
1~3
1
0~63
Key Code
Refer to p. 39
* When setting the 21 ~ 29, a menu doesn’t display on screen.
Transmission / Receiving Protocol
Transmission
[Command1][Command2][ ][Set ID][ ][Data][Cr]
* [Command 1]
* [Command 2]
* [Set ID]
* [DATA]
* [Cr]
* [ ]
: First command to control PDP set.
(j or k)
: Second command to control PDP set.
: You can adjust the set ID to choose
desired monitor ID number in special
menu.
Adjustment range is 1 ~ 99.
When selecting Set ID ‘0’, every
connected PDP set is controlled.
Set ID is indicated as decimal (1~99) on
menu and as Hexa decimal (0x0~0x63)
on transmission/receiving protocol.
: To transmit command data.
Transmit ‘FF’ data to read status of
command.
: Carriage Return
ASCII code ‘0x0D’
: ASCII code ‘space (0x20)’
OK Acknowledgement
[Command2][ ][Set ID][ ][OK][Data][x]
* The Monitor transmits ACK (acknowledgement) based on
this format when receiving normal data. At this time, if the
data is data read mode, it indicates present status data. If
the data is data write mode, it returns the data of the PC
computer.
Error Acknowledgement
[Command2][ ][Set ID][ ][NG][Data][x]
* The Monitor transmits ACK (acknowledgement) based on
this format when receiving abnormal data from
non-viable functions or communication errors.
Data 1: Illegal Code
2: not support function
3: Wait more time
Owner’s Manual 35
Miscellaneous
01. Power (Command 2 : a)
04. Screen Mute (Command 2 : d)
G To control Power On/Off of the TV.
G To select screen mute on/off.
Transmission
Transmission
[k][d][ ][Set ID][ ][Data][Cr]
[k][a][ ][Set ID][ ][Data][Cr]
Data 0 : Power Off
1 : Power On
Ack
Data 0 : Screen mute off (Picture on)
1 : Screen mute on (Picture off)
Ack
[d][ ][Set ID][ ][OK][Data][x]
[a][ ][Set ID][ ][OK][Data][x]
G To show Power On/Off.
Transmission
05. Volume Mute (Command 2 : e)
[k][a][ ][Set ID][ ][FF][Cr]
G To control volume mute on/off.
You can also adjust mute using the MUTE button on
remote control.
Transmission
Ack
[a][ ][Set ID][ ][OK][Data][x]
* In like manner, if other functions transmit ‘0xFF’ data
based on this format, Acknowledgement data feed back
presents status about each function.
[k][e][ ][Set ID][ ][Data][Cr]
Data 0 : Volume mute off (Volume on)
1 : Volume mute on (Volume off)
Ack
02. Input Select (Command 2 : b)
[e][ ][Set ID][ ][OK][Data][x]
G To select input source for the TV.
You can also select an input source using the INPUT
SELECT button on the Monitor's remote control.
06. Volume Control (Command 2 : f)
G To adjust volume.
You can also adjust volume with the volume buttons
on remote control.
Transmission
[k][b][ ][Set ID][ ][Data][Cr]
Data 0
1
2
3
4
: TV
: AV1
: AV2
: S-Video2
: AV3
5
6
7
8
9
: AV4
: AV5
: Component
: RGB
: HDMI
Ack
Transmission
[k][f][ ][Set ID][ ][Data][Cr]
Data Min : 0 ~ Max : 64
* Refer to ‘Real data mapping 1’. See page 39.
Ack
[f][ ][Set ID][ ][OK][Data][x]
[b][ ][Set ID][ ][OK][Data][x]
07. Contrast (Command 2 : g)
03. Aspect Ratio (Command 2 : c) (Main Picture Size)
G To adjust the screen format. (Main picture format)
You can also adjust the screen format using the ARC
(Aspect Ratio Control) button on remote control or in the
SCREEN menu.
Transmission
[k][c][ ][Set ID][ ][Data][Cr]
Data 1
2
3
4
:
:
:
:
Normal screen (4:3)
Wide screen (16:9)
Spectacle
Full screen (Zoom)
6 : Original
7 : Wide screen (14:9)
8 : Full (Option)
Ack
[c][ ][Set ID][ ][OK][Data][x]
* Using the PC input, you select either 16:9 or 4:3 screen
aspect ratio.
G To adjust screen contrast.
You can also adjust contrast in the PICTURE menu.
Transmission
[k][g][ ][Set ID][ ][Data][Cr]
Data Min : 0 ~ Max : 64
* Refer to ‘Real data mapping 1’. See page 39.
Ack
[g][ ][Set ID][ ][OK][Data][x]
08. Brightness (Command 2 : h)
G To adjust screen brightness.
You can also adjust brightness in the PICTURE menu.
Transmission
[k][h][ ][Set ID][ ][Data][Cr]
Data Min : 0 ~ Max : 64
* Refer to ‘Real data mapping 1’. See page 39.
Ack
[h][ ][Set ID][ ][OK][Data][x]
36 PLASMA TV
09. Colour (Command 2 : i)
14. Treble (Command 2 :r)
G To adjust the screen colour.
You can also adjust colour in the PICTURE menu.
G To adjust treble.
You can also adjust treble in the SOUND menu.
Transmission
[k][i][ ][Set ID][ ][Data][Cr]
Transmission
Data Min : 0 ~ Max : 64
* Refer to ‘Real data mapping 1’. See page 39.
Ack
[i][ ][Set ID][ ][OK][Data][x]
Data Min : 0 ~ Max : 64
* Refer to ‘Real data mapping 1’. See page 39.
[k][r][ ][Set ID][ ][Data][Cr]
Ack
[r][ ][Set ID][ ][OK][Data][x]
10. Tint (Command 2 : j) (option)
G To adjust the screen tint.
You can also adjust tint in the PICTURE menu.
Transmission
[k][j][ ][Set ID][ ][Data][Cr]
15. Bass (Command 2 : s)
G To adjust bass.
You can also adjust bass in the SOUND menu.
Transmission
Data Red : 0 ~ Green : 64
* Refer to ‘Real data mapping 1’. See page 39.
Ack
[j][ ][Set ID][ ][OK][Data][x]
[k][s][ ][Set ID][ ][Data][Cr]
Data Min : 0 ~ Max : 64
* Refer to ‘Real data mapping 1’. See page 39.
Ack
[s][ ][Set ID][ ][OK][Data][x]
11. Sharpness (Command 2 : k)
G To adjust the screen sharpness.
You can also adjust sharpness in the PICTURE menu.
Transmission
[k][k][ ][Set ID][ ][Data][Cr]
Data Min : 0 ~ Max : 64
* Refer to ‘Real data mapping 1’. See page 39.
Ack
[k][ ][Set ID][ ][OK][Data][x]
16. Balance (Command 2 : t)
G To adjust balance.
You can also adjust balance in the SOUND menu.
Transmission
[k][t][ ][Set ID][ ][Data][Cr]
Data Min : 0 ~ Max : 64
* Refer to ‘Real data mapping 1’. See page 39.
Ack
[t][ ][Set ID][ ][OK][Data][x]
12. OSD Select (Command 2 : l)
G To select OSD (On Screen Display) on/off when controlling remotely.
G To adjust colour temperature.
You can also adjust CSM in the PICTURE menu.
Transmission
[k][l][ ][Set ID][ ][Data][Cr]
Data 0 : OSD off
17. Colour Temperature (Command 2 : u)
1 : OSD on
Transmission
[k][u][ ][Set ID][ ][Data][Cr]
Ack
Data 0: Cool
[l][ ][Set ID][ ][OK][Data][x]
1: Normal
2: Warm
3: User
Ack
13. Remote control lock mode (Command 2 : m)
G To lock the front panel controls on the monitor and remote
control.
Transmission
[k][m][ ][Set ID][ ][Data][Cr]
Data 0 : Lock off
[u][ ][Set ID][ ][OK][Data][x]
18. Red Adjustment (Command 2 : v)
G To adjust red in colour temperature.
Transmission
1 : Lock on
Ack
[m][ ][Set ID][ ][OK][Data][x]
* If you’re not using the remote control, use this mode.
When main power is on/off, external control lock is
released.
[k][v][ ][Set ID][ ][Data][Cr]
Data Min : 0 ~ Max : 50
* Refer to ‘Real data mapping 2’. See page 39.
Ack
[v][ ][Set ID][ ][OK][Data][x]
Owner’s Manual 37
ENGLISH
Miscellaneous
Miscellaneous
19. Green Adjustment (Command 2 : w)
G To adjust green in colour temperature.
23. Low Power
(Command 1 : j, Command 2 : q)
G To reduce the power consumption of the monitor. You
can also adjust Low Power in SPECIAL menu.
Transmission
[k][w][ ][Set ID][ ][Data][Cr]
Data Min : 0 ~ Max : 50
* Refer to ‘Real data mapping 2’. See page 39.
Ack
[w][ ][Set ID][ ][OK][Data][x]
Transmission
[j][q][ ][Set ID][ ][Data][ ][Cr]
Data 0 : Off
1 : On
Ack
[q][ ][Set ID][ ][OK][Data][x]
20. Blue Adjustment (Command 2 : $)
G To adjust blue in colour temperature.
24. Orbiter Time Setting
(Command 1 : j, Command 2 : r)
Transmission
[k][$][ ][Set ID][ ][Data][Cr]
Data Min : 0 ~ Max : 50
* Refer to ‘Real data mapping 2’. See page 39.
Ack
[$][ ][Set ID][ ][OK][Data][x]
G To adjust orbiter operation time term.
Transmission
[j][r][ ][Set ID][ ][Data][ ][Cr]
Data Min: 1 ~ Max: FE
* Refer to ‘Real data mapping 1’. See page 39.
Ack
21. Abnormal State (Command 2 : z)
[r][ ][Set ID][ ][OK][Data][x]
G To recognize an abnormal state.
Transmission
Data FF : Read
25. Orbiter Pixel Setting
(Command 1 : j, Command 2 : s)
Ack
G To adjust pixel number in orbiter function.
[z][ ][Set ID][ ][OK][Data][x]
Transmission
Data 0: Normal (Power on and signal exist)
1: No signal (Power on)
2: Turn the TV off by remote control
3: Turn the TV off by sleep time function
4: Turn the TV off by RS-232C function
5: 5V down
6: AC down
7: Turn the TV off by Fan Alarm function (option)
8: Turn the TV off by Off time function
9: Turn the TV off by Auto sleep function
a: Turn the TV off by AV board detect
[j][s][ ][Set ID][ ][Data][Cr]
[k][z][ ][Set ID][ ][FF][ ][Cr]
* This function is “read only”.
22. ISM Method
(Command 1 : j, Command 2 : p)
G To control the ISM method. You can also adjust ISM
Method in SPECIAL menu.
Transmission
[j][p][ ][Set ID][ ][Data][Cr]
Data 0 : Normal Mode
1 : White Wash
Ack
[p][ ][Set ID][ ][OK][Data][x]
38 PLASMA TV
2 : Orbiter
3 : Inversion
Data Min: 1 ~ Max: 3
* Refer to ‘Real data mapping 1’. See page 39.
Ack
[s][ ][Set ID][ ][OK][Data][x]
26. Auto Configure
(Command 1 : j, Command 2 : u)
28. Key
(Command 1 : m, Command 2 : c)
G To adjust picture position and minimize image shaking
automatically. It works only in RGB (PC) mode.
G To send IR remote key code.
ENGLISH
Miscellaneous
Transmission
Transmission
[m][c][ ][Set ID][ ][Data][Cr]
[j][u][ ][Set ID][ ][Data][Cr]
Data Key code - Refer to page 41.
Data 1: To set
Ack
Ack
[c][ ][Set ID][ ][OK][Data][x]
[u][ ][Set ID][ ][OK][Data][x]
27. Programme selection
(Command 1 : m, Command 2 : a)
G To select a programme for the main picture.
Transmission
[m][a][ ][Set ID][ ][Data0][ ][Data1][ ][Data2][Cr]
Data0 Min: 0 ~ Max: 63 (0 ~ C7, 200Pr is on)
* Refer to ‘Real data mapping 1’.
Data1 Don’t care
Data2 0 : Main
29. Input select (Command 1 : x, Command 2 : b)
G To select input source for TV
Transmission
[x][b][ ][Set ID][ ][Data][Cr]
Data Structure
MSB
0
Ack
LSB
0
0
0
0
External Input
0
0
0
Input Number
[a][ ][Set ID][ ][OK][Data0][x]
External Input
* Real data mapping 1
0 : Step 0
A : Step 10 (Set ID 10)
F : Step 15 (Set ID 15)
10 : Step 16 (Set ID 16)
64 : Step 100
* Real data mapping 2
0 : -40
1 : -39
2 : -38
Data
0
0
0
1
Analog
0
0
1
0
AV
0
1
0
0
Component
0
1
0
1
RGB-DTV
0
1
1
0
RGB-PC
1
0
0
1
HDMI
28 : 0
4E : +38
4F : +39
50 : +40
Input Number
Data
0
0
0
0
Input1
6E : Step 110
0
0
0
1
Input2
73 : Step 115
74 : Step 116
0
0
1
0
Input3
0
0
1
1
Input4
C7 : Step 199
0
1
0
0
Input5
FE : Step 254
FF : Step 255
0
1
0
1
Input6
Ack
[b][ ][Set ID][ ][OK][Data][x]
Owner’s Manual 39
Miscellaneous
IR Code (NEC Format)
How to connect
G Connect your wired remote control to the Remote Control port on the Monitor.
Remote Control IR Code (NEC Format)
G Output waveform
Single pulse, modulated with 37.917KHz signal at 455KHz
TC
Carrier frequency
FCAR = 1/TC = fOSC/12
Duty ratio = T1/TC = 1/3
T1
G Configuration of frame
• 1st frame
Lead
code
Low
custom code
High
custom code
Data code
Data code
C0 C1 C2 C3 C4 C5 C6 C7 C0 C1 C2 C3 C4 C5 C6 C7 D0 D1 D2 D3 D4 D5 D6 D7 D0 D1 D2 D3 D4 D5 D6 D7
• Repeat frame
Repeat code
Tf
G Lead code
9 ms
4.5 ms
0.55 ms
G Repeat code
9 ms
2.25 ms
G Bit description
• Bit “0”
• Bit “1”
0.56 ms
0.56 ms
1.12 ms
2.24 ms
G Frame interval : Tf
The waveform is transmitted as long as a key is depressed.
Tf
Tf
Tf=108ms @455KHz
40 PLASMA TV
Code (Hexa)
00
01
02
03
08
C4
C5
09
10
11
12
13
14
15
16
17
18
19
0B
98
BF
C6
D5
D6
5A
D0
D1
D2
CF
D3
1A
0A
0E
43
44
4D
52
53
20
2A
22
24
26
62
64
65
70
5C
5D
79
76
77
AF
Function
PR (D)
PR (E)
VOL (G)
VOL (F)
POWER
POWER ON
POWER OFF
MUTE
Number Key 0
Number Key 1
Number Key 2
Number Key 3
Number Key 4
Number Key 5
Number Key 6
Number Key 7
Number Key 8
Number Key 9
TV/AV
MULTIMEDIA
COMPONENT
HDMI
RGB
TV
AV1
AV2
AV3
AV4
AV5
S-Video2
Q.VIEW
I/II
SLEEP
MENU
OK( )
PSM
SSM
LIST
TEXT
REVEAL
MODE
MIX
TIME
UPDATE
SIZE
HOLD
INDEX
Zoom +
Zoom ARC
ARC (4:3)
ARC (16:9)
ARC (Zoom)
ENGLISH
Miscellaneous
Note
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button (Power On/Off)
Discrete IR Code (Only Power On)
Discrete IR Code (Only Power Off)
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
Discrete IR Code (Input COMPONENT Selection)
Discrete IR Code (Input HDMI Selection)
Discrete IR Code (Input RGB Selection)
Discrete IR Code (Input TV Selection)
Discrete IR Code (Input AV1 Selection)
Discrete IR Code (Input AV2 Selection)
Discrete IR Code (Input AV3 Selection)
Discrete IR Code (Input AV4 Selection)
Discrete IR Code (Input AV5 Selection)
Discrete IR Code (Input S-Video2 Selection)
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
Discrete IR Code (Only 4:3 mode)
Discrete IR Code (Only 16:9 mode)
Discrete IR Code (Only Zoom mode)
Owner’s Manual 41
Miscellaneous
Troubleshooting Checklist
• Check whether the set is turned on.
No picture &
No sound
• Power cord inserted into wall outlet?
• Plug another product’s power cord into the wall outlet where the set’s power
cord was plugged in.
• Press the VOLUME (G) button.
Picture OK &
No sound
• Sound muted? Press MUTE button.
• Check whether the TV speaker is “on” in the SOUND menu.
• Check to see if there is any object between the set and the remote control
causing obstruction.
The remote control
doesn’t work
• Check to see if the batteries are installed with the correct polarities.
(Refer to p.6)
• Check if the remote control handset is set up to correct mode.
• Install new batteries. (Refer to p.6)
Picture appears slowly,
after switching on
• This is normal as the image is muted during the startup process of the set.
Please contact your service centre, if the picture has not appeared after five
minutes.
• Select Colour in the PICTURE menu and press the VOLUME (G) button.
(Refer to p.23)
No or Poor colour
or Poor picture
• Keep a certain distance between the set and the VCR.
• Activate any function to restore the brightness of the picture.
(If still picture is on the screen for more than 5 minutes, the screen gets dark.)
Horizontal/vertical bars
or picture shaking
No output from one of the
speakers
Unusual sound from
inside the set
42 PLASMA TV
• Check for local interference such as an electrical appliance or power tool.
• Adjust Balance in the SOUND menu. (Refer to p.24)
• A change in ambient humidity or temperature may result in an unusual noise
at the time of switching off or on of the set and does not indicate a fault with
the set.
Miscellaneous
ENGLISH
Product Specifications
42PX3RVA
42PX2RVA
42PX3RVA-ZC
42PX2RVA-ZC
Width (inches / mm)
47.64 / 1210
47.7 / 1210
Height (inches / mm)
27.60 / 701
27.4 / 696
Depth (inches / mm)
11.61 / 295
10.7 / 270
Weight (pounds / kg)
66.14 / 30
77.2 / 35
MODEL
Power requirement
AC100-240V, 50/60Hz
Operating Temperature Range
32 ~ 104°F (0 ~ 40°C)
Operating Humidity Range
Less than 80%
50PX3R
MODEL
•
50PX3R-ZC
Width (inches / mm)
55.1 / 1400
Height (inches / mm)
32.3 / 821
Depth (inches / mm)
3.9 / 99
Weight (pounds / kg)
115 / 52.15
Power requirement
AC100-240V, 50/60Hz
Operating Temperature Range
32 ~ 104°F (0 ~ 40°C)
Operating Humidity Range
Less than 80%
The specifications shown above may be changed without notice for quality improvement.
Owner’s Manual 43
Download PDF

advertising