LG | 42PX4RV | Datasheet | LG 42PX4RV plasma panel

PLASMA TV
OWNER’S MANUAL
Please read this manual carefully before operating your set.
Retain it for future reference.
Record model number and serial number of the set.
See the label attached on the back cover and quote this information to your dealer when you require service.
Model number
Serial number
:
:
P/NO : 3828VA0525F (MF056A, 151E TX) d
Safety Warnings
Safety Instructions
WARNING
W
Do not place the set in direct sunlight or near heat
sources such as heat registers, stove and so on.
- This may cause a fire.
Do not use the set in damp place such as a bathroom
or any place where it is likely to get wet.
- This may cause a fire or could give an electric shock.
Do not use water while cleaning the set.
- This may cause damaged the set or could give an electric
shock.
In case of smoke or strange smell from the set, switch
it off ,unplug it from the wall outlet and contact your
dealer or service center.
- This may cause a fire or could give an electric shock.
Bend antenna cable between inside and outside
building to prevent rain from flowing in.
- This may cause water damaged inside the set and could give an
electric shock.
Do not attempt to service the set yourself. Contact
your dealer or service center.
- This may cause damaged the set or could give an electric
shock.
Earth wire should be connected.
- If the earth wire is not connected, there is possible a danger of
electric shock caused by the current leakage.
- If grounding methods are not possible, a separate circuit breaker should be employed and installed by a qualified electrician.
Power
supplier
During storm activity, unplug the set from the wall
outlet and don’t touch an antenna cable.
- This may cause damaged the set or could give an electric
shock.
DISCONNECTING DEVICE FROM MAINS
- Mains plug is the disconnecting device. The plug must remain
readily operable.
Short-circuit
breaker
- Do not connect ground to telephone wires, lightning rods or gas
pipe.
Apparatus shall not be exposed to dripping or splashing and no objects filled with liquids, such as vases,
shall be placed on the apparatus.
Do not insert any object into the exhaust vent.
- This may cause a fire or could give an electric shock.
Do not place heavy objects on the set.
- This may cause serious injury to a child or adult.
WARNING in U.K. only
*
This set is supplied with a BS 1363 approved 13 amp mains plug, fused at 13 amp. When replacing the fuse
always use a 13 amp BS 1362, BSI or ASTA approved type. Never use this plug with the fuse cover omitted. To
obtain a replacement fuse cover contact your dealer or “LG Electronics U.K. Ltd.” If the type of plug supplied is not
suitable for the mains sockets in your home, then the plug should be removed and a suitable type fitted.
A mains plug removed from the mains lead of this set must be destroyed. A mains plug with bared wires is
hazardous if inserted in a mains socket. Do not connect either wire to the earth pin, marked with the letter E or
with the earth symbol
or coloured green or green and yellow. If any other plug is fitted, use a 13 amp fuse,
either in the plug, or at the distribution board.
The wires in this mains lead are coloured in accordance with the following codes: BLUE: NEUTRAL, BROWN: LIVE
As the colours of the wires in the mains lead of this set may not correspond with the coloured marking identifying the terminals in your plug, proceed as follows: The wire which is coloured blue must be connected to the terminal which is marked with the letter N or coloured black. The wire which is coloured brown must be connected
to the terminal which is marked with the letter L or coloured red.
2 PLASMA TV
ENGLISH
Safety Warnings
* Safety instructions have two kinds of information, and each meaning of it is as below.
WARNING The violation of this instruction may cause serious injuries and even death.
NOTES
The violation of this instruction may cause light injuries or damage of the
product.
Take care of danger that may happen under specific condition.
NOTES
Never touch the power plug with a wet hand.
- This may cause an electric shock.
Ensure the power cord doesn’t trail across any hot
objects like a heater.
- This may cause a fire or an electric shock.
Disconnect from the mains and remove all connections before moving.
Do not plug in unit if power cord or plug is damaged or
the connecting part of the power outlet is loose.
Do not place the set in a built-in installation such as a
bookcase or rack.
- This may cause a fire or an electric shock.
- Ventilation required.
Dispose of used batteries carefully to prevent a child
from eating them.
- In case of a child eating them, contact doctor immediately.
When moving the set assembled with speakers do not
carry holding the speakers.
- This may cause the set to fall, causing serious injury to a child or
adult, and serious damage to the Monitor.
Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners.
When installing the set on a table, be careful not to
place the edge of its stand on the end of the table.
- This may cause damage the set or could give an electric shock.
- This may cause the set to fall, causing serious injury to a child or
adult, and serious damage to the set.
Contact the service center once a year to clean the
internal part of the set.
- Accumulated dust can cause mechanical failure.
The distance between eyes and the screen should be
approx. 5 ~ 7 times the diagonal length of the screen
away.
- If not, eyes will strain.
Unplug the set from the wall outlet when it is left unattended
and unused for long periods of time or occurred a state of
emergency.
Do not place an outside antenna in the vicinity of overhead power lines or other electric light or power circuits.
- Accumulated dust may cause a fire or an electric shock from
deterioration through electric leakage.
- This may cause an electric shock.
There should be enough distance between an outside
antenna and power lines to keep the former from
touching the latter even when the antenna falls.
- This may cause an electric shock.
Do not pull the plug not the cord when disconnecting.
- This may cause a fire.
Owner’s Manual 3
Contents
Contents
Safety Warnings
Safety Instructions . . . . . . . . . . . . . . . . . . . . . . .2~3
Introduction
Remote Control Key Functions . . . . . . . . . . . . . . . .6
Location and Function of Controls . . . . . . . . . . .7~8
Installation
External Equipment Viewing Setups . . . . . . . . .9~12
Displayable Monitor Specification . . . . . . . . . . . . .13
HDMI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14~15
Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
Installation Options . . . . . . . . . . . . . . . . . . . . . . .17
Operation
Turning on the Set . . . . . . . . . . . . . . . . . . . . . . . .18
On-Screen Menu Language Selection (option) . . .18
Channel Menu Options
Auto Programme Tuning . . . . . . . . . . . . . . . . . . .19
Manual Programme Tuning . . . . . . . . . . . . . . . . .19
Fine Tuning . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
Assigning a Station Name . . . . . . . . . . . . . . . . . .20
Booster (option) . . . . . . . . . . . . . . . . . . . . . . . . . .20
Programme Edit . . . . . . . . . . . . . . . . . . . . . . . . . .21
Favourite Programme . . . . . . . . . . . . . . . . . . . . .21
Calling up the Programme Table . . . . . . . . . . . . .21
Picture Menu Options
PSM (Picture Status Memory) . . . . . . . . . . . . . . .22
CSM (Colour Status Memory) . . . . . . . . . . . . . . .22
Manual Colour Temperature Control . . . . . . . . . .22
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
sRGB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
ACM (Active Colour Management) . . . . . . . . . . . .23
Manual Picture Control . . . . . . . . . . . . . . . . . . . .23
Sound Menu Options
SSM (Sound Status Memory) . . . . . . . . . . . . . . . .24
BBE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24
AVL (Auto Volume Leveler) . . . . . . . . . . . . . . . . .24
Adjusting Sound Control . . . . . . . . . . . . . . . . . . .24
TV speaker . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25
Stereo/Dual Reception . . . . . . . . . . . . . . . . . . . . .25
NICAM Reception (option) . . . . . . . . . . . . . . . . . .25
Time Menu Options
Setting the Clock . . . . . . . . . . . . . . . . . . . . . . . . .26
Setting the On/Off Timer . . . . . . . . . . . . . . . . . . .26
Auto Sleep . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26
Sleep Timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26
Special Menu Options
Child Lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27
ISM (Image Sticking Minimization) Method . . . . . .27
Low Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28
Demo . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28
Screen Menu Options
Auto Configure . . . . . . . . . . . . . . . . . . . . . . . . . .29
Manual Configure . . . . . . . . . . . . . . . . . . . . . . . .29
Selecting Wide VGA/XGA mode . . . . . . . . . . . . .29
Setting Picture Format . . . . . . . . . . . . . . . . . . . . .30
Picture Size Zoom . . . . . . . . . . . . . . . . . . . . . . . .30
Screen Position . . . . . . . . . . . . . . . . . . . . . . . . . .31
Cinema . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31
NR (Noise Reduction) . . . . . . . . . . . . . . . . . . . . .31
Initializing (Reset to original factory value) . . . . . .31
PIP (Picture-in-Picture) Feature
Watching PIP . . . . . . . . . . . . . . . . . . . . . . . . . . . .32
Programme Selection for Sub Picture . . . . . . . . . .32
Selecting an Input Signal Source for the PIP . . . .32
Moving the PIP (PIP mode only) . . . . . . . . . . . . .32
POP (Picture-out-of-Picture: Channel Scan) . . . . .32
Picture Size . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32
Adjusting the screen for the PIP . . . . . . . . . . . . . .32
Adjusting PIP Transparency (PIP mode only) . . . .32
Teletext (option)
Switch on/off . . . . . . . . . . . . . . . . . . . . . . . . . . . .33
SIMPLE Text (option) . . . . . . . . . . . . . . . . . . . . . .33
TOP Text (option) . . . . . . . . . . . . . . . . . . . . . . . . .33
FASTEXT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34
Special Teletext Functions . . . . . . . . . . . . . . . . . .34
Miscellaneous
External Control Device Setup . . . . . . . . . . . .35~41
IR Code (NEC Format) . . . . . . . . . . . . . . . . . .42~43
Programming the Remote . . . . . . . . . . . . . . . . . .44
Programming Codes . . . . . . . . . . . . . . . . . . .45~46
Troubleshooting Checklist . . . . . . . . . . . . . . . . . .50
Product Specifications . . . . . . . . . . . . . . . . . . . . .51
Disposal of your old appliance
After reading this manual, keep it in a place
where the user can refer
to easily.
4 PLASMA TV
1. When this crossed-out wheeled bin symbol is attached to a product it
means the product is covered by the European Directive 2002/96/EC.
2. All electrical and electronic products should be disposed of separately
from the municipal waste stream via designated collection facilities
appointed by the government or the local authorities.
3. The correct disposal of your old appliance will help prevent potential
negative consequences for the environment and human health.
4. For more detailed information about disposal of your old appliance,
please contact your city office, waste disposal service or the shop
where you purchased the product.
Introduction
ENGLISH
Introduction
What is a Plasma Display ?
If voltage is inputted to gas in glass panels, ultraviolet rays are outputted and fused with a fluorescent substance. At this moment,
light is emitted. A Plasma Display is a next generation flat Display using this phenomenon.
160° - Wide angle range of vision
A Plasma Display provides more than 160° angle range of vision so that you can get a picture without distortion from any
direction.
Easy installation
A Plasma Display is much lighter and smaller than other same class products so that you can install the Plasma Display
in the desired place.
Big screen
The screen of a Plasma Display is 42" (or 50")so that you can get vivid experience as if you are in a theater.
Multimedia Plasma Display
A Plasma Display can be connected with a computer so that you can use it as a screen for conference, game, internet
and so on.
The explanation about coloured dots may be present on PDP screen
The PDP which is the display device of this product is composed of 0.9 to 2.2 million cells and a few cell defects can occur
in the manufacture of the PDP. Several coloured dots visible on the screen would be acceptable, in line with other PDP
manufacturers and would not mean that the PDP is faulty. We hope you will understand that the product which corresponds to this standard is regarded as acceptable. It means that it could not be changed or refunded.
We promise that we'll do our best to develop our technology to minimize the cell defects.
The explanation about noise of 42" (or 50") PDP (option)
In the same way that a fan is used in a PC to keep the CPU cool, the PDP is equipped with cooling fans to improve the
reliability of this product. Therefore, a certain level of noise could occur when the fan is operated. This noise doesn't have
any negative effect on its efficiency and reliability and it's also determined to have no difficulty while using this product.
The noise from the fans is normal in the operation of this product. We hope you will understand that a certain level of noise
is acceptable. It means that it is not changeable nor refundable.
WARNING
TO REDUCE THE RISK OF FIRE AND ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO
RAIN OR MOISTURE.
Owner’s Manual 5
Introduction
Remote Control Key Functions
- When using the remote control aim it at the remote control sensor of the set.
- There's maybe a defect in consecutive operation of remote control in specified brightness according to this set feature.
INPUT
Selects the TV, AV, Component, RGB or
HDMI modes.
switches the set on from standby.
MODE
Selects another device.
MULTIMEDIA
INPUT
POWER
DVD
TV
MODE
CABLE
SLEEP
Sets the sleep timer.
ZOOM -
T/
*
LIST
ARC
I/II
Selects the language during dual language broadcast.
Selects the sound output.
EXIT
LIST
Displays the programme table.
OK
PIP P
R-
MUTE
Switches the sound on or off.
I/II
MENU
Displays on screen menus one by one.
Exits the current menu.
Memorizes menu changes.
SSM
To select the sound appropriate to your
viewing programme.
MUT
E
SLEEP
U
MEN
PIP
Switches the sub picture on or off.
Selects PIP or DW modes.
PIP PR + /Selects a programme for the sub picture.
SWAP
Alternates between main and sub picture.
PIP INPUT
Selects the input mode for the sub picture.
SIZE
Adjusts the sub picture size.
POSITION
Moves the sub picture to D / E or F / G
direction.
ZOOM +
PIP
TEX
MULTIMEDIA
Selects the Component, RGB or HDMI
modes.
switches the set on from standby.
VCR
STB
AUDIO
ZOOM - / ZOOM +
Enlarges or reduces the main picture size.
POWER
switches the set on from standby or off to
standby.
PUT
PIP PR +
VOL
SSM
SWAP
PSM
EXIT
Clears all on-screen displays and returns
to TV viewing from any menu.
PIP IN
PR
ARC
Changes the picture format.
OK
accepts your selection or displays the current mode.
D / E or F / G
Adjusts menu settings.
Selects menu item.
FAVOURITE
Q.VIEW
SIZE
POSITION
INDEX
HOLD
TIME
REVEAL
MIX
MODE
VOL +/- (Volume Up/Down)
Increases/decreases sound level.
PR +/- (Programme Up/Down)
Selects a programme.
NUMBER buttons
?
FAVOURITE
selects a favorite programme.
TEXT/
These buttons are used for teletext.
For further details, see the ‘Teletext’ section.
Note : In teletext mode, the PIP PR +/-,
SWAP and PIP INPUT buttons are used for
teletext function.
*
M
PSM
Adjusts the factory preset picture according to the room.
Q.VIEW
Returns to the previously viewed programme.
VCR BUTTONS
Controls a LG video cassette recorder.
Installing Batteries
• Open the battery compartment cover on the back side and insert
the batteries with correct polarity.
• Install two 1.5V alkaline batteries of AA type. Don’t mix used batteries with new batteries.
6 PLASMA TV
Introduction
ENGLISH
Location and Function of Controls
<Front Panel Controls>
7
8
TV/AV
2
INPUT
MENU
3
4
1
1. Power Button
Switches the set on from standby or off to standby.
2. Remote Control Sensor
3. INPUT Button
Selects the TV, AV, Component, RGB or HDMI modes.
Switches the set on from standby.
4. MENU
Displays on screen menus one by one.
Exits the current menu.
Memorizes menu changes.
OK
5
VOL
MENU
OK
VOL
PR
PR
6
6. D / E (Programme Up/Down)
Selects a programme or a menu item.
Switches the set on from standby.
F / G (Volume Up/Down)
Adjusts the volume.
Adjusts menu settings.
7. Power Indicator
Illuminates red in standby mode, Illuminates green when the
set is turned on
8. Intelligent Eye
Adjusts picture according to the surrounding conditions.
5. OK
Accepts your selection or displays the current mode.
Owner’s Manual 7
Introduction
Location and Function of Controls
- Shown is a simplified representation of the set.
- What is shown here may be somewhat different from your set.
- This manual explains the features available on the 42PX4R series.
<Back Panel>
AV5
VIDEO
S-VIDEO
R AUDIO L/MONO
9
VIDEO
AUDIO
L
HDMI/
DVI(VIDEO)
AUDIO INPUT
R
AV2
VARIABLE
V
ARIABLE
AUDIO OUT
RS-232C INPUT
(CONTROL/SERVICE)
Antenna
AUDIO
L
REMOTE
CONTROL
AC INPUT
AV1
R
COMPONENT
RGB INPUT
AV4
AV3
L
S-VIDEO VIDEO
R
(MONO)
AUDIO
1
2
3
4
1. HDMI(DVI VIDEO) / AUDIO INPUT / RGB INPUT
Connect the monitor output socket of the PERSONAL COMPUTER, DVD or STB to this socket.
Note: If you want to use RGB/DVI audio, we strongly recommend that you use the cable that has a core, or the EMI Filter
core along with separate cable.
2. REMOTE CONTROL
3. RS-232C INPUT(CONTROL/SERVICE) PORT
Connect to the RS-232C port on a PC.
4. COMPONENT INPUT
Connect DVD video outputs to Y, PB, PR of COMPONENT
INPUT and audio outputs to Audio sockets of AUDIO INPUT.
AUDIO/VIDEO IN SOCKETS (AV4)
Connect the audio/video out sockets of external equipment to
these sockets.
S-VIDEO/AUDIO IN SOCKETS
Connect the S-VIDEO out socket of an VCR to the S-VIDEO
socket.
Connect the audio out sockets of the VCR to the audio sockets as in AV4.
8 PLASMA TV
5
6
7
8
5. VARIABLE AUDIO OUTPUT
6. EURO SCART SOCKET
Connect the euro scart socket of the VCR to these sockets.
Note:
a. If you want to use the EURO scart cable, you have to use
the signal shielded Euro scart cable.
b. If the S-VIDEO(Y/C) signal is received through the Euro scart
socket 2 (AV 2), you must change to the S-Video 2 (Y/C) mode.
7. ANTENNA INPUT
8. POWER CORD SOCKET
This Monitor operates on AC power. The voltage is indicated
on the Specifications page. Never attempt to operate the set
on DC power.
9. AUDIO/VIDEO INPUT (AV5)
S-VIDEO/AUDIO IN SOCKETS
Installation
ENGLISH
External Equipment Viewing Setups
Antenna Connection
- Be careful not to bend the bronze wire when connecting to an antenna port.
Apartments
(connecting to wall antenna socket)
Antenna
wall antenna socket
< Back panel of the set >
RF coaxial wire (75 ohms)
VHF antenna
UHF antenna
outdoor antenna
Private house
(connecting to wall outdoor antenna)
Watching VCR
- When connecting the set to external equipment, match the colours of connecting ports (Video - yellow, Audio (L) - white, Audio
(R) -red).
- Connect the VIDEO INPUT socket (yellow) of external equipment to the VIDEO INPUT on the set.
- If you have a mono VCR, connect the audio cable from the VCR to the AUDIO (L/MONO) input on the set.
- If you connect an S-VIDEO VCR to the S-VIDEO input, the picture quality is improved; compared to connecting a regular VCR
to the Video input.
Or, connect the Euro scart socket of the VCR to the Euro scart socket of the set.
- Use the orbiter function to Avoid having a fixed image remain on the screen for a long period of time. Typically a frozen still picture from a VCR. (Refer to p. 27)
If a 4:3 picture format is used, the fixed image may remain visible on the screen.
- To avoid picture noise (interference), leave an adequate distance between the VCR and set.
< Back panel of the set >
Watching TV programmes
- Turn the set on and select the programme you
want.
Watching VCR
1. Use the INPUT button on the remote control to
select AV1, AV2, S-Video2, AV3, AV4 or AV5.
- If both S-VIDEO and VIDEO sockets have been
connected to the S-VHS VCR simultaneously,
only the S-VIDEO can be received.
2. Insert a video tape into the VCR and press the
PLAY button on the VCR.
(See VCR owner’s manual)
VIDEO
AUDIO
L
AV1
R
L
R
AV2
VARIABLE
VARIABLE
AUDIO OUT
RS-232C INPUT
(CONTROL/SERVICE)
Antenna
AUDIO
COMPONENT
RGB INPUT
AV4
AV3
L
S-VIDEO VIDEO
R
(MONO)
AUDIO
< VCR >
Owner’s Manual 9
Installation
External Equipment Viewing Setups
Watching Cable TV
- After subscribing for a local cable TV station and installing a converter you can watch cable TV.
- For further information of cable TV, contact the local cable TV station.
< Back panel of the set >
VIDEO
AV1
R
Antenna
AUDIO
L
R
VARIABLE
V
ARIABLE
AUDIO OUT
C INPUT
L/SERVICE)
1. Use the INPUT button on the remote control to
select AV1, AV2, S-Video2, AV3, AV4 or AV5.
- If both S-VIDEO and VIDEO sockets have been
connected to the Cable box simultaneously, only
the S-VIDEO can be received.
2. Select your desired channel with the remote
control for cable box.
AUDIO
L
COMPONENT
NPUT
To watch cable TV
AV2
AV4
AV3
L
S-VIDEO VIDEO
R
(MONO)
AUDIO
< Cable box >
Watching external AV source
- When connecting the set to an external source, match the colours of AUDIO/VIDEO input jacks on the set with the output jacks
on the audio/video equipment: Video = yellow, Audio (Left) = white, Audio (Right) = red.
Or, connect the Euro scart socket of the VCR to the Euro scart socket of the set.
How to use
1. Use the INPUT button on the remote control to
select AV1, AV2, S-Video2, AV3, AV4 or AV5.
2. Operate the corresponding external equipment.
See external equipment operating guide.
< Back panel of the set >
VIDEO
AUDIO
L
AV1
R
L
R
VARIABLE
V
ARIABLE
AUDIO OUT
PUT
VICE)
Antenna
AUDIO
COMPONENT
UT
AV2
AV4
AV3
L
S-VIDEO VIDEO
R
(MONO)
AUDIO
Camcorder
R
Video game set
10 PLASMA TV
AUDIO
L
VIDEO
ENGLISH
Installation
Watching DVD
How to connect
Connect DVD video outputs to Y, PB, PR of COMPONENT INPUT and audio outputs to Audio sockets of
AUDIO INPUT.
How to use
1. Turn on the DVD player, and insert a DVD.
2. Use INPUT or MULTIMEDIA button on the remote
control to select Component.
Refer to the DVD player's manual for operating
instructions.
< Back panel of the set >
VIDEO
AUDIO
L
HDMI/
(VIDEO)
AUDIO INPUT
AV1
R
AUDIO
COMPONENT
RGB INPUT
L
EMOTE
ONTROL
RS-232C INPUT
(CONTROL/SERVICE)
R
R
VARIABLE
V
ARIABLE
AUDIO OUT
R
AV2
AV4
AV3
L
S-VIDEO VIDEO
R
(MONO)
AUDIO
• Component Input ports
You can get better picture quality if you connect
DVD player with component input ports as below.
Component ports of the
set
Video output ports
of DVD player
R
R
PR
Y
PB
Y
Y
Y
Y
Pr
Pb
B-Y R-Y
Cb Cr
PB PR
< DVD player >
Owner’s Manual 11
Installation
External Equipment Viewing Setups
Connecting PC
- To enjoy vivid picture and sound, connect a PC to the set.
- Avoid keeping a fixed image on the set’s screen for a long period of time. The fixed image may become permanently imprinted on
the screen; use a screen saver when possible.
- Connect PC to the RGB INPUT(PC INPUT) or HDMI INPUT(DIGITAL RGB INPUT) port of the set; change the resolution output
of PC accordingly.
- There might be noise according to some resolution, vertical pattern, contrast or brightness in PC mode. Change the PC mode into
another resolution or change the refresh rate into another rate or adjust the brightness and contrast on the menu until the picture
is clean. If the refresh rate of the PC graphic card can not be changed, change the PC graphic card or consult it to the manufacturer of the PC graphic card.
- The synchronization input waveform for Horizontal and Vertical frequencies are separate.
Setup Instructions to Connect a PC to your set
- We recommend using 1024x768, 60Hz for the PC mode, they provide the best picture quality.
In 42PX4RV series, we recommend using 640x480, 60Hz for the PC mode, they provide the best picture quality.
- If the resolution of PC is over UXGA, there will be no picture on the set.
- Connect the signal cable from the monitor output port of the PC to the RGB INPUT port of the set or the signal cable from the
HDMI output port of the PC to the HDMI INPUT port on the set.
- Connect the audio cable from the PC to the Audio input on the set. (Audio cables are not included with the set).
- If using a sound card, adjust PC sound as required.
- This set uses a VESA Plug and Play Solution. The set provides EDID data to the PC system with a DDC protocol. The PC adjusts
automatically to use this set.
- DDC protocol is preset for RGB (Analog RGB), HDMI (Digital RGB) mode.
- If required, adjust the settings for Plug and Play functionally.
- If graphics card on the PC does not output analog and digital RGB simultaneously, connect only one of RGB INPUT or HDMI
INPUT to display the PC on the set.
If graphic card on the PC does output analog and digital RGB simultaneously, set the set to either RGB or HDMI ; (the other mode
is set to Plug and Play automatically by the set.)
- DOS mode may not work depending on video card if you use a HDMI to DVI cable.
- When you use too long RGB-PC cable, there might be a noise on the screen. We recommend using under 5m of the cable. It provides the best picture quality.
< Back panel of the set >
VIDEO
AUDIO
L
HDMI/
DVI(VIDEO)
AUDIO INPUT
AV1
R
AUDIO
COMPONENT
RGB INPUT
L
REMOTE
CONTROL
VARIABLE
V
ARIABLE
AUDIO OUT
RS-232C INPUT
(CONTROL/SERVICE)
R
AV2
AV4
AV3
L
S-VIDEO VIDEO
R
(MONO)
AUDIO
12 PLASMA TV
PC Setup
1. Turn on the PC and apply power to the set.
2. Turn on the display by pressing the POWER button on
the set’s remote control.
3. Use the INPUT or MULTIMEDIA button on the remote
control to select the RGB or HDMI input source.
4. Set the resolution output of the PC to SXGA or under
(1280 x 1024, 60Hz). (Refer to p. 13)
Installation
RGB / HDMI mode
Resolution
640x350
ENGLISH
Displayable Monitor Specification
RGB / HDMI mode
Horizontal
Vertical
Frequency(KHz) Frequency(Hz)
31.468
70.09
31.469
70.08
37.927
85.03
59.94
31.469
59.94
35.000
66.66
35.000
66.66
37.861
72.80
37.861
72.80
37.500
75.00
37.500
75.00
43.269
85.00
43.269
85.00
31.500
60.00
31.500
60.00
37.799
70.00
37.799
70.00
39.375
75.00
39.375
75.00
31.500
60.00
31.500
60.00
37.799
70.00
37.799
70.00
39.375
75.00
39.375
75.00
35.156
56.25
35.156
56.25 (RGB)
37.879
60.31
37.879
60.31
48.077
72.18
48.077
72.18
46.875
75.00
46.875
75.00
53.674
85.06
53.674
85.06
49.725
74.55
49.725
74.55
48.363
60.00
48.363
60.00
56.476
70.06
56.476
70.06
60.023
75.02
60.023
75.02
68.677
85.00
68.677
85.00
54.348
60.05
47.700
60.00
63.995
70.01
59.625
75.02
67.500
75.00
68.500
85.00
1152x870
68.681
75.06
47.700
60.00
1280x960
60.023
60.02
59.625
75.02
1280x1024
63.981
60.02
69.500
85.00
54.348
60.05
63.995
70.01
67.500
75.00
77.487
85.00
68.681
75.06
47.693
60.00
60.091
75.00
848x480
852x480
800x600
832x624
1024x768
1152x864
31.469
70.08
37.927
85.03
31.469
640x350
85.08
640x480
85.08
Horizontal
Vertical
Frequency(KHz) Frequency(Hz)
31.468
70.09
37.861
720x400
37.861
Resolution
720x400
640x480
848x480
852x480
800x600
832x624
1024x768
1360x768
1366x768
42PX4RV series
1152x864
1152x870
1280x768
68.504
85.00
1280x960
60.023
60.02
1280x1024
63.981
60.02
42PX4R series
50PX4R series
Owner’s Manual 13
Installation
-
HDMITM, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing.
This set can receive the High-Definition Multimedia Interface (HDMI) or Input of Digital Visual Interface(DVI).
This set supports HDCP (High-bandwidth Digital Contents Protection) Protocol for the set (480p, 720p, 1080i) modes.
When you connect to HDMI/DVI Source devices (DVD Player, STB or PC) that support AUTO HDMI/DVI Plug & Play, this sets
the HDMI/DVI source devices automatically. (1280 x 720p) (or 42PX4RV series : 640 x 480p).
Afer reading HDMI/DVI source devices, using Display Data Channel (DDC) Protocol, Extended Display Identification Data
(EDID) stored in the set is used.
If HDMI/DVI Source devices do not support AUTO HDMI/DVI, the resolution is set manually.
- To get the best picture quality, adjust the DVD Player or Set Top Box output resolution to 1280 x 720p (or 42PX4RV series : 640 x 480p).
- To get the best picture quality, adjust the PC graphics card to 1024 x 768 (or 42PX4RV series : 640 x 480), 60Hz.
- When Source Devices have DVI Output Connector, you must connect audio with separated cable.(Refer to <How to connect>)
How to connect
1. When Source Devices (DVD Player or Set Top Box) support HDMI.
- If Source Devices have HDMI Output Connector, Source Devices connect to the set with HDMI Cable .(not supplied with the product).
- If Source Devices support Auto HDMI, automatically, Source Devices divert output resolution in 1280 x 720p (or 42PX4RV series :
640 x 480p). But if not, resolution divert Manually Setting for reference Manual of Source Devices.
- To get the best picture quality, adjust the DVD Player or Set Top Box output resolution to 1280 x 720p (or 42PX4RV series : 640 x
480p).
- Because HDMI sends Digital Video and Audio with one cable, there is no need for Audio Cable when using HDMI Cable.
2. When Source Devices (DVD Player or Set Top Box) supports DVI.
- If Source Devices have DVI Output Connector, Source Devices connect to the set with HDMI to DVI Cable (not supplied with the
product).
- If Source Devices support Auto DVI, automatically, Source Devices divert output resolution in 1280 x 720p (or 42PX4RV series : 640
x 480p). But if not, resolution divert Manually Setting for reference Manual of Source Devices.
- To get the best picture quality, adjust the DVD Player or Set Top Box output resolution to 1280 x 720p (or 42PX4RV series : 640 x
480p).
- In this case, Audio use other cable. When Source Devices have Analog Audio Output Connector, RGB/DVI Audio Input of the set
connect to Audio Cable (not supplied with the product). And then you can listen to normal Audio.
3.
-
When PC supports DVI.
If PC has a DVI Output Connector, Source Devices connect to the set with HDMI to DVI Cable (not supplied with the product).
To get the best picture quality, adjust the PC graphics card to 1024 x 768 (or 42PX4RV series : 640 x 480), 60Hz.
Use the the set’s HDMI/DVI (VIDEO) for video connections, depending on your PC connector.
If the graphics card on the PC does not output analog RGB and DVI simultaneously, connect only one of either RGB Input or
HDMI/DVI Input to display the PC on the set.
- If the graphics card on the PC does output analog RGB and DVI simultaneously, the set to either RGB Input or HDMI/DVI Input;
(the other mode is set to Plug and Play automatically by the set.)
- Then, make the corresponding audio connections. If using a sound card, adjust the PC sound as required.
- In this case, Audio use other cable. When PC (or sound card of PC) have Analog Audio Output Connector, RGB/DVI Audio Input
of the set connect to Analog Audio Cable (not supplied with the product). And then you can listen to normal Audio.
14 PLASMA TV
Installation
ENGLISH
Reference
Cable sample
HDMI Cable
(not supplied with the product)
HDMI to DVI Cable
(not supplied with the product)
Analog Audio Cable (RCA type)
(not supplied with the product)
Analog Audio Cable (Stereo to RCA type)
(not supplied with the product)
How to use
1.
2.
3.
4.
Connect the HDMI/DVI Source Devices(DVD Player or Set Top Box or PC) and the set.
Turn on the display by pressing the POWER button on the set and HDMI/DVI Source Devices remote control.
Select HDMI/DVI Input source in Main Input option of PIP/DW menu.
Check the image on your set. There may be noise associated with the resolution, vertical pattern, contrast or brightness in
HDMI/DVI Source Devices. If noise is present, change the HDMI/DVI Source Devices to another resolution, change the refresh
rate or adjust the brightness and contrast on the menu until the picture is clear. If the refresh rate of the PC graphics card can not
changed, change the PC graphics card or consult the manufacturer of the PC graphics card.
Notes:
- Depending on the graphics card, DOS mode may not work if you use a HDMI to DVI Cable.
- Avoid keeping a fixed image on the set screen for a long period of time. The fixed image may become permanently imprinted on
the screen. Use the Orbiter screen saver when possible.
- When Source Devices connected HDMI/DVI Input, output PC Resolution(VGA, SVGA, XGA), Position, Size may not fit to Screen.
As shown the lower picture, press the MENU button to adjust the screen Position of the set and contact an PC graphics card service center.
- When Source Devices connected HDMI/DVI Input output the set Resolution(480p, 720p, 1080i), the set Display fit EIA/CEA-861B Specification to Screen. If not, refer to the Manual of HDMI/DVI Source Devices or contact your service center.
- In case of HDMI/DVI Source Devices are not connected, Cable or poor cable connection, "No Signal" OSD display in HDMI/DVI
Input. And In case of Video Resolution not supported when output is HDMI/DVI Source Devices, "No Signal" OSD display. Refer
to the Manual of HDMI/DVI Source Devices or contact your service center.
Owner’s Manual 15
Installation
Accessories
MULTIMEDIA
INPUT
POWER
DVD
TV
VCR
MODE
CABLE
STB
AUDIO
ZOOM -
ZOOM +
PIP
TEXT/
*
SLEEP
MUTE
LIST
I/II
ARC
EXIT
MENU
OK
PIP PR
-
PIP PR +
VOL
SSM
SWAP
PSM
FAVOURITE
PIP INPUT
PR
Q.VIEW
SIZE
POSITION
INDEX
HOLD
TIME
REVEAL
MIX
MODE
?
M
LG TV
AS mark
Owner’s Manual
Remote Control handset
2-Eye Bolts
Power Cord
2-Wall brackets
1.5V
1.5V
Alkaline batteries
Fixing the set assembly to the wall to protect the set tumbling
- Secure the set assembly by fixing it to a wall by using the Eye Bolts/Wall brackets.
• If the set is mounted on a desk top, insert the 2 Eye-Bolts and tighten them
securely in the upper holes as shown.
Insert the 2 Eye Bolts and tighten securely, in the holes on the bracket.
Install the wall brackets on the wall with 2 bolts, (not supplied with the product),
as shown.
Match the height of the Eye Bolts and the wall brackets.
Check to be sure the brackets are tightened securely.
• Secure the set assembly to the wall with strong strings or wound wire cables,
(not supplied with the product), as shown.
Optional Extras
-
40
42
-
Optional extras can be changed or modified for quality improvement. Without any notification new optional extras can be
added.
Contract your dealer for buying these items.
40
50
16 PLASMA TV
42
Tilt wall mounting bracket
Ceiling mounting bracket
Video cables
Audio cables
Installation
ENGLISH
Installation Options
• The set can be installed in different ways such as on a wall, or on a desktop etc.
• Install this set only in a location where adequate ventilation is available.
Wall Mount: Horizontal Installation
Desktop Pedestal Installation
• The set can be installed on a wall as shown above.
(For further information, refer to the optional ‘Wall
Mounting Bracket Installation and Setup Guide’.)
To Mount on a Wall
Wall mount minimum allowable clearances for adequate ventilation.
• The set can be mounted on a desk as shown above.
To Install on a Desktop
Pedestal mount minimum allowable clearances for
adequate ventilation.
10cm
3cm
10cm
10cm
10cm
Swivel function (option)
• After installing the set, you can adjust the the set manually to the left or right direction by 20 degrees to suit your viewing position.
Note : Before adjusting the angle, you must loosen (to the left) the shaft bolt on the middle of stand’s back. And when
stand be level with set, you must close (to the right) the shaft bolt to set the hole.
Owner’s Manual 17
Operation
Turning on the Set
- When using the remote control, aim it at its sensor on the set.
Turning on the set just after installation
1. Connect power cord correctly, the set is switched to standby mode.
2. Press the r / I, INPUT or PR D / E button on the set or press the POWER, INPUT, MULTIMEDIA, PR
NUMBER buttons on the remote control and then the set will switch on.
D
/
E
or
D
/
E
or
Turning on the set (power cord is still connected)
If the set was turned off with the remote control power button and the r / I button on the set
• Press the r / I, INPUT or PR D / E button on the set or press the POWER, INPUT, MULTIMEDIA, PR
NUMBER button on the remote control to turn the set on.
On-Screen Menu Language Selection (option)
- The menus can be shown on the screen in the selected language. First select your language.
1. Press the MENU button and then use
2. Press the G button and then use D /
E
D
/
E
button to select the SPECIAL menu.
button to select Language.
3. Press the G button and then use D / E button to select your desired language.
From this point on, the on-screen menus will be shown in the language of your choice.
4. Press the EXIT button to return to normal TV viewing.
18 PLASMA TV
Operation
ENGLISH
Channel Menu Options
Auto Programme Tuning
- All stations that can be received are stored by this method. It is recommended that you use auto programme during
installation of this set.
1. Press the MENU button and then use D / E button to select the STATION menu.
2. Press the G button and then D / E button to select Auto programme.
3. Press the G button to select System. Select a TV system with the F / G button;
L : SECAM L/L’ (option)
BG : PAL B/G, SECAM B/G (Europe / East Europe / Asia / New Zealand / M.East / Africa
/Australia)
I
: PAL I/II (U.K. / Ireland / Hong Kong / South Africa)
DK : PAL D/K, SECAM D/K (East Europe / China / Africa / CIS)
M : (USA / Korea / Philippines) (option)
4. Press the E button to select Storage from. Select the beginning programme number
with the F / G button or NUMBER buttons on the Storage from menu.
5. Press the E button to select Start.
6. Press the G button to begin auto programming.
All receivable stations are stored.
STATION
PICTURE
Auto programme
programme G
Auto
Manual programme
Programme edit
Favourite programme
System
BG
Storage from
2
Start
SOUND
TIME
SPECIAL
SCREEN
PIP/DW
Menu Prev.
Note : In some models, the station name is stored for stations which broadcast VPS
(Video Programme Service), PDC (Programme Delivery Control) or TELETEXT data. If
no station name can be assigned to a station, the channel number is assigned and
stored as C (V/UHF 01-69) or S (Cable 01-47), followed by a number.
To stop auto programming, press the MENU button.
When auto programming is completed, the Programme edit menu appears on the
screen. See the ‘Programme edit’ section to edit the stored programme.
Manual Programme Tuning
- Manual programme lets you manually tune and arrange the stations in whatever order you desire. Also you can
assign a station name with five characters to each programme number.
1. Press the MENU button and then use D / E button to select the STATION menu.
2. Press the G button and then D / E button to select Manual programme.
3. Press the G button to select Storage. Select the desired programme number with the
F / G button or NUMBER buttons on the Storage menu.
4. Press the E button to select System. Select a TV system with the F / G button;
L : SECAM L/L’ (option)
BG : PAL B/G, SECAM B/G (Europe / East Europe / Asia / New Zealand / M.East / Africa
/Australia)
I
: PAL I/II (U.K. / Ireland / Hong Kong / South Africa)
DK : PAL D/K, SECAM D/K (East Europe / China / Africa / CIS)
M : (USA / Korea / Philippines) (option)
5. Press the E button to select Band. Press the F / G button to select V/UHF or Cable
as required.
6. Press the E button to select Channel. You can select the desired channel number with
the F / G button or NUMBER buttons. If possible, select the channel number directly with
the number buttons.
7. Press the E button to select Search. Press the F / G button to commence searching. If
a station is found the search will stop.
8. Press the OK button to store it.
9. To store another station, repeat steps 3 to 8.
STATION
Auto programme
Manual programme
Manual
programme G
PICTURE
Programme edit
Favourite programme
Storage
2
System
BG
Band
V/UHF
SOUND
Channel
TIME
Fine
SPECIAL
Search
Name
SCREEN
PIP/DW
Booster
1
C
01
Off
Menu Prev.
Owner’s Manual 19
Operation
Channel Menu Options
Fine Tuning
- Normally fine tuning is only necessary if reception is poor.
1.
2.
3.
4.
Repeat the ‘Manual programme tuning’ steps 1 to 2.
Press the G button and then D / E button to select Fine.
Press the F / G button to fine tune for the best picture and sound.
Press the OK button.
The finely tuned programme will be indicated by a yellow number during programme
selection.
5. Press the EXIT button to return to normal TV viewing.
STATION
Auto programme
Manual programme
Manual
programme
PICTURE
Programme edit
Favourite programme
SOUND
Storage
2
System
BG
Band
V/UHF
1
Channel
Fine
TIME
Search
SPECIAL
Name
SCREEN
C
Booster
PIP/DW
01
Off
Store
Assigning a Station Name
1. Repeat the ‘Manual programme tuning’ steps 1 to 2.
2. Press the G button and then D / E button to select Name.
3. Press the G button to display the Name menu.
4. Press the D button. You can use a blank, +, -, the alphabet A to Z and the numeric 0 to
9.
With the E button you can select in the opposite direction.
5. Select the next position by pressing the G button and then make your choice of the second character, and so on.
6. Press the OK button in twice.
7. Press the EXIT button to return to normal TV viewing.
STATION
PICTURE
Auto programme
Manual programme
Manual
programme
Programme edit
Favourite programme
SOUND
Storage
2
System
BG
Band
V/UHF
1
Channel
TIME
Fine
Search
SPECIAL
Name
C
01
SCREEN
Booster
PIP/DW
Off
Prev.
Booster (option)
In some models, Booster is an optional function. Only a set with Booster can perform this function.
If the reception is poor at the fringe area of TV signal, select Booster to On.
1.
2.
3.
4.
5.
Repeat the ‘Manual programme tuning’ steps 1 to 2.
Press the G button and then D / E button to select Booster.
Press the F / G button to select On or Off.
Press the OK button.
Press the EXIT button to return to normal TV viewing.
STATION
Auto programme
Manual programme
Manual
programme
PICTURE
Programme edit
Favourite programme
Storage
2
System
BG
Band
SOUND
Channel
TIME
Fine
V/UHF
1
Search
SPECIAL
Name
C
SCREEN
PIP/DW
20 PLASMA TV
Booster
Store
01
F G Off
ENGLISH
Operation
Programme Edit
- This function enables you to delete or skip the stored programmes. Also you can move some stations to other programme numbers or copy a blank station data into the selected programme number.
1. Press the MENU button and then use D / E button to select the STATION menu.
2. Press the G button and then D / E button to select Programme edit.
3. Press the G button to display the Programme edit menu.
CHANNEL
Programme
edit
0
1
2
3
4
Deleting a programme
1. Select a programme to be deleted with the D / E or F / G button.
2. Press the RED button twice.
The selected programme is deleted, all the following programmes are shifted up one
position.
----BLN 2
C 01
C 04
C 05
Delete
Move
5
6
7
8
9
C
C
C
S
S
05
07
55
27
29
Copy
Skip
Menu Prev.
Copying a programme
1. Select a programme to be copied with the D / E or F / G button.
2. Press the GREEN button.
All the following programmes are shifted down one position.
Moving a programme
1. Select a programme to be moved with the D / E or F / G button.
2. Press the YELLOW button.
3. Move the programme to the desired programme number with the
4. Press the YELLOW button again to release this function.
D /E
or
F /G
button.
Skipping a programme number
1. Select a programme number to be skipped with the D / E or F / G button.
2. Press the BLUE button. The skipped programme turns to blue.
3. Press the BLUE button again to release the skipped programme.
When a programme number is skipped it means that you will be unable to select it using
the PR D / E button during normal TV viewing. If you want to select the skipped programme, directly enter the programme number with the NUMBER buttons or select it in
the programme edit or table menu.
Favourite Programme
- This function lets you select your favourite programmes directly.
1.
2.
3.
4.
5.
Press the MENU button and then use D / E button to select the STATION menu.
Press the G button and then D / E button to select Favourite programme.
Press the G button to display the Favourite programme menu.
Press the D / E button to select -- -----.
Select a desired programme with the F / G button or NUMBER buttons. Any number
under 10 is entered with a numeric ‘0’ (or ‘00’) in front of it, i.e. ‘05’ (or ‘005’) for 5.
6. To store another programme, repeat steps 4 to 5.
You can store up to 8 programmes.
7. Press the OK button.
8. Press the EXIT button to return to normal TV viewing.
STATION
PICTURE
Auto programme
Manual programme
Programme edit
Favourite
Favourite programme G
SOUND
0 BLN 2
--- -- ----- -- ----- -- ---
TIME
--- -- ---
SPECIAL
--- -- ----- -- ---
SCREEN
--- -- ---
PIP/DW
Menu Prev.
Repeatedly press the FAVOURITE button to select stored favorite programmes.
Calling up the Programme Table
- You can check the programmes stored in the memory by displaying the programme table.
Displaying programme table
Press the LIST button to display the Programme table menu.
The programme table appears on the screen.
•
•
You may find some blue highlighted programmes shown. They have been set up in the
programme edit mode.
Some programmes with the channel number shown in the programme table indicate
there is no station name assigned.
0
1
2
3
4
----BLN 2
C 01
C 04
C 05
5
6
7
8
9
C
C
C
S
S
05
07
55
27
29
Selecting a programme in the programme table
Select a programme with the D / E or F / G button.
Then press the OK button.
The Plasma Display switches to the chosen programme number.
Paging through a programme table
There are 10 programme table pages in which contain 100 programmes.
Pressing the D / E or F / G button repeatedly turns the pages.
Press the LIST button to return to normal TV viewing.
Owner’s Manual 21
Operation
Picture Menu Options
PSM (Picture Status Memory)
- This function adjusts the set to the best picture appearance.
- When adjusting picture options (contrast, brightness, colour, sharpness and tint (NTSC AV only)) manually, PSM is
automatically changed to User.
1. Press the PSM button
• Each press of the PSM button changes the screen display as shown below.
Intelligent Eye
Dynamic
Standard
Mild
User
• You can also select Intelligent Eye, Dynamic, Standard, Mild or User in the PICTURE menu.
• Picture options Intelligent Eye, Dynamic, Standard and Mild are preset and programmed for good
picture quality at the factory and cannot be changed.
• When the eye function is on, the most suitable picture is automatically adjusted according to the surrounding conditions.
CSM (Colour Status Memory)
- To initialize values (reset to default settings), select the Normal option.
1. Press the MENU button and then use
2. Press the
G
button and then use D
D /E
/E
button to select the PICTURE menu.
button to select CSM.
STATION
SOUND
3. Press the
ture.
G
button and then use D
/E
button to select the desired colour tempera-
4. Press the EXIT button to return to normal TV viewing.
• Each press of
D
Cool
/
E
button changes the screen display as shown below.
Normal
Warm
PSM
CSM
G
PICTURE
TIME
ACM
Contrast
Brightness
Colour
Sharpness
Cool
Normal
Warm
100
60
50
50
User
Red
0
SPECIAL
Green
0
SCREEN
Blue
0
PIP/DW
Menu Prev.
User
Manual Colour Temperature Control
- You can adjust red, green, or blue to any colour temperature you prefer.
1. Press the MENU button and then use
2. Press the
G
3. Press the
G
4. Press the
G
button and then use
D /E
D /E
button to select the PICTURE menu.
button to select CSM.
STATION
SOUND
button and then use D
button and then use
/E
button to select User.
D / E / F / G button
to make appropriate adjustments.
5. Press the EXIT button to return to normal TV viewing.
PSM
CSM
G
PICTURE
TIME
ACM
Contrast
Brightness
Colour
Sharpness
Cool
Normal
Warm
100
60
50
50
User
Red
0
SPECIAL
Green
0
SCREEN
Blue
0
PIP/DW
Menu Prev.
- You can enjoy the vivid and hi-definition picture with LG’s Excellent Digital Reality processor technology.
- It’s not available to use this function in RGB[PC], HDMI[PC] mode.
- When selecting picture options (Intelligent Eye, Dynamic, Standard and Mild) in PICTURE menu, XD is automatically changed to On.
1. Press the MENU button and then use
2. Press the
G
button and then use D
D /E
/E
button to select the PICTURE menu.
button to select XD.
STATION
SOUND
3. Press the
G
button and then use
D /E
button to select On or Off.
4. Press the EXIT button to return to normal TV viewing.
PSM
CSM
G
PICTURE
TIME
ACM
Contrast
Brightness
Colour
Sharpness
SPECIAL
SCREEN
PIP/DW
22 PLASMA TV
Menu Prev.
100
60
50
50
On
Off
ENGLISH
Operation
sRGB
- When the set was connected to external equipment with sRGB function, It’s adjusted a colour difference to display
the equal image each other.
- This function works in the following mode:RGB[PC], HDMI[PC].
1. Press the MENU button and then use
2. Press the
G
button and then use D
3. Press the
G
button and then use
D /E
/E
button to select the PICTURE menu.
button to select sRGB.
STATION
SOUND
D /E
button to select On or Off.
4. Press the EXIT button to return to normal TV viewing.
PSM
CSM
PICTURE
sRGB
ACM
Contrast
Brightness
G
100
60
On
Off
TIME
SPECIAL
SCREEN
PIP/DW
Menu Prev.
ACM (Active Colour Management)
- Adjust the ACM to select the desired skin colour option.
- This function works in the following mode:
TV, AV1, AV2, S-Video2, AV3, AV4, AV5 or COMPONENT, RGB[DTV], HDMI[DTV].
- It’s not available to use this function in XD Off mode.
1. Press the MENU button and then use
2. Press the
G
button and then use
3. Press the G button and then use
D
D /E
button to select the PICTURE menu.
/ E button to select ACM.
F / G button
to make appropriate adjustments.
4. Press the EXIT button to return to normal TV viewing.
STATION
PSM
CSM
PICTURE
SOUND
TIME
ACM
Contrast
Brightness
Colour
Sharpness
G
100
60
50
50
Fleshtone
0
Greentone
0
Bluetone
0
SPECIAL
SCREEN
PIP/DW
Menu Prev.
Manual Picture Control
- You can adjust picture contrast, brightness, colour, sharpness and tint (NTSC AV only) to the levels you prefer.
- It’s not available to use colour, sharpness function in RGB[PC], HDMI[PC] mode.
- In the broadcasting system PAL/SECAM, the picture item Tint doesn’t work.
1. Press the MENU button and then use
button to select the PICTURE menu.
STATION
button to select the desired picture option.
PICTURE
D /E
2. Press the G button and then use
D /E
3. Press the G button and then use
F / G button
to make appropriate adjustments.
4. Press the EXIT button to return to normal TV viewing.
SOUND
TIME
PSM
CSM
ACM
Contrast
Contrast
Brightness
Colour
Sharpness
100
100 G
60
50
50
SPECIAL
SCREEN
PIP/DW
Menu Prev.
Owner’s Manual 23
Operation
Sound Menu Options
SSM (Sound Status Memory)
- This function lets you enjoy the best sound without any special adjustment because the set automatically selects the
appropriate sound option based on the program content.
- When adjusting sound options (treble and bass) manually, SSM is automatically changed to User.
1. Press the SSM button.
2. Press the SSM button to select your desired sound.
SRS TSXT
Flat
Music
Movie
Sports
User
• You can also select SRS TSXT, Flat, Music, Movie, Sports or User in the SOUND menu.
• The sound SRS TSXT, Flat, Music, Movie and Sports are programmed for good sound reproduction at the factory
and cannot be changed.
R
-
TruSurround XT
is a trademark of SRS Labs, Inc.
- TruSurround XT technology is incorporated under license from SRS Labs, Inc.
BBE
- BBE High Definition Sound restores clarity and presence for better speech intelligibility and musical realism.
1. Press the MENU button and then use
D /E
button to select the SOUND menu.
2. Press the
G
button and then use
D /E
button to select BBE.
3. Press the
G
button and then use
D /E
button to select On or Off.
STATION
PICTURE
SOUND
4. Press the EXIT button to return to normal TV viewing.
TIME
SSM
BBE
BBE
AVL
Balance
Treble
Bass
TV Speaker
G
On
Off
G
On
Off
0
50
50
SPECIAL
SCREEN
Manufactured under license from BBE Sound, Inc.
PIP/DW
Menu Prev.
AVL (Auto Volume Leveler)
- This feature maintains an equal volume level; even if you change channels.
1. Press the MENU button and then use
2. Press the
G
button and then use
D /E
D /E
button to select the SOUND menu.
button to select AVL.
STATION
PICTURE
SOUND
3. Press the
G
button and then use
D /E
button to select On or Off.
4. Press the EXIT button to return to normal TV viewing.
TIME
SSM
BBE
AVL
AVL
Balance
Treble
Bass
TV Speaker
0
50
50
SPECIAL
SCREEN
PIP/DW
Menu Prev.
Adjusting Sound Control
1. Press the MENU button and then use D
2. Press the G button and then use
D /E
/E
button to select the SOUND menu.
button to select the desired sound item.
STATION
PICTURE
SOUND
3. Press the
G
button and then use
F /G
button to make appropriate adjustments.
4. Press the EXIT button to return to normal TV viewing.
TIME
SSM
BBE
AVL
Balance
Treble
Treble
Bass
TV Speaker
SPECIAL
SCREEN
Note : Treble, Bass or BBE aren’t suitable to use SRS TSXT.
24 PLASMA TV
PIP/DW
Menu Prev.
0
50
50 G
50
ENGLISH
Operation
TV Speaker
- You can adjust internal speaker status.
- In COMPONENT, RGB[PC] and HDMI[PC] mode, TV speaker/variable audio can be output even though there is no
video signal.
- If you want to use your external hi-fi stereo system, turn off the internal speakers of the set.
1. Press the MENU button and then use
D /E
2. Press the
G
button and then use
D
3. Press the
G
button and then use
D /E
button to select the SOUND menu.
/ E button to select TV Speaker.
STATION
PICTURE
SOUND
button to select On or Off.
4. Press the EXIT button to return to normal TV viewing.
TIME
SSM
BBE
AVL
Balance
Treble
Bass
TV speaker
Speaker
TV
0
50
50
G
On
Off
SPECIAL
SCREEN
PIP/DW
Menu Prev.
Stereo / Dual Reception
- When a programme is selected, the sound information for the station appears after the programme number and station name disappear.
On Screen Display
Press the I/II button to received broadcast state.
Broadcast
Mono
Stereo
Dual
On screen Display
MONO
STEREO
DUAL I
Mono Sound Selection
In stereo reception if the stereo signal is weak, you can switch to mono by pressing the
I/II button twice. In mono reception the depth of sound is improved. To switch back to
stereo, press the I/II button twice again.
Language Selection for Dual Language Broadcast
If a programme received in two languages (dual language), you can switch to DUAL I,
DUAL II or DUAL I + II by pressing the I/II button repeatedly.
• DUAL I sends the primary broadcast language to the loudspeakers.
• DUAL II sends the secondary broadcast language to the loudspeakers.
• DUAL I + II sends a separate language to each loudspeaker.
NICAM Reception (option)
- If your Plasma Display is equipped with the PDP Tuner for NICAM reception, the high quality NICAM (Near
Instantaneous Companding Audio Multiplex) digital sound can be received.
Sound output can be selected according to the type of received broadcast as follows by
pressing the I/II button repeatedly.
• When NICAM mono is received, you can select NICAM MONO or FM MONO.
• When NICAM stereo is received, you can select NICAM STEREO or FM MONO. If
the stereo signal is weak, switch to FM mono.
• When NICAM dual is received, you can select NICAM DUAL I, NICAM DUAL II,
NICAM DUAL I + II, or MONO. When FM mono is selected the display MONO
appears on the screen.
Sound output selection
In AV, Component, RGB or HDMI mode, you can select output sound for the left and right
loudspeakers.
Repeatedly press the I/II button to select the sound output.
• L+R : Audio signal from audio L input is sent to left loud-speaker and audio signal from
audio R input is sent to right loud-speaker.
• L+L : Audio signal from audio L input is sent to left and right loud-speakers.
• R+R : Audio signal from audio R input is sent to left and right loud-speakers.
Owner’s Manual 25
Operation
T ime Menu Options
Setting the Clock
- If current time setting is erased by a power failure or the set is unplugged, reset the clock.
1. Press the MENU button and then use
D
/
E
button to select the TIME menu.
2. Press the
G
button and then use
D
/ E button to select Clock.
3. Press the
G
button and then use
D
/
E
button to adjust the hour.
4. Press the
G
button and then use
D
/
E
button to adjust the minute.
STATION
PICTURE
Clock
Clock
Off time
On time
Auto sleep
--
G
:
--
SOUND
TIME
SPECIAL
5. Press the EXIT button to return to normal TV viewing.
SCREEN
PIP/DW
Menu Prev.
Setting the On/Off Timer
- Timer function operates only if current time has been already set.
- Off Timer function overrides on Timer function if they are set to the same time.
- The set must be in standby mode for the On Timer to work.
1. Press the MENU button and then use
2. Press the
3. Press the
G
G
button and then use
button and then use
D
/
E
button to select the TIME menu.
STATION
/ E button to select Off time or On time.
D
D
/
E
PICTURE
Clock
Off time
time
On time
Auto sleep
G
SOUND
button to select On.
12
TIME
4. Press the
G
button and then use
D
/
E
button to adjust the hour.
5. Press the
G
button and then use
D
/
E
button to adjust the minute.
6. Only On time function; Press the
gramme number or volume level.
G
button and then use
D
/
E
On
Off
SPECIAL
PIP/DW
30
1
Menu Prev.
7. Press the EXIT button to return to normal TV viewing.
- To cancel Off/On time function
Press the D / E button to select Off in step 3.
- Two hours after the set is switched on by the on time function it will automatically switch back to standby mode
unless a button has been pressed.
Auto Sleep
- If there is no input signal, the monitor turn off automatically after 10 minutes.
1. Press the MENU button and then use
D
/
E
button to select the TIME menu.
2. Press the G button and then use
D
/
E
button to select Auto sleep.
3. Press the G button and then use
D
/
E
button to select On or Off.
STATION
PICTURE
Clock
Off time
On time
Autosleep
sleep
Auto
SOUND
TIME
4. Press the EXIT button to return to normal TV viewing.
SPECIAL
SCREEN
PIP/DW
Menu Prev.
Sleep Timer
- Sleep timer turns the set off at the preset time.
zz
- Press the SLEEP button to select the number of minutes. The display
--- Min will appear on the screen, followed by 10, 20, 30, 60, 90, 120, 180 and 240 minutes. The timer begins to count down from the number of minutes
selected.
a. To check the remaining sleep time, press the SLEEP button once.
b. To cancel the sleep time, repeatedly press the SLEEP button until the display
c. If you turn the set off after setting the sleep timer, the setting will be erased.
26 PLASMA TV
zz
--- Min
appears.
G
00
Programme
SCREEN
button to adjust pro-
:
Volume
On
Off
Operation
ENGLISH
Special Menu Options
Child Lock
- The set can be set up so that it can only be used with the remote control.
1. Press the MENU button and then
2. Press the
G
button and then
D
3. Press the G button and then D /
/
D
E
E
/
E
button to select the SPECIAL menu.
button to select Child lock.
button to select On or Off.
STATION
PICTURE
SOUND
Language
Child lock
lock
Child
ISM Method
Low power
Set ID
Demo
G
On
Off
TIME
4. Press the EXIT button to return to normal TV viewing.
SPECIAL
SCREEN
PIP/DW
Menu Prev.
- This set programmed to remember which option it was last set to even if you turn the set off.
- In Child lock ‘On’, if the set is turned off, press the INPUT, PR D / E button on the set or POWER, INPUT, MULTIMEDIA, PR D / E or NUMBER buttons on the remote control.
- With the Child lock On, the display ‘ Child lock on’ appears on the screen if any button on the front panel is
pressed while viewing the set.
ISM (Image Sticking Minimization) Method
- Frozen still picture from a PC/video game displayed on the screen for prolonged periods will result in an ghost
image remaining even when you change the image. Avoid allowing a fixed image to remain on the set's screen for
a long period of time.
1. Press the MENU button and then use
2. Press the
G
button and then
D /E
D /E
button to select the SPECIAL menu.
button to select ISM Method.
STATION
PICTURE
SOUND
3. Press the G button and then D / E button to select either Normal, White wash,
Orbiter or Inversion. If you unnecessary to set this function, set Normal.
Language
Child lock
Method
ISM Method
Low power
Set ID
Demo
G
Normal
White wash
Orbiter
Inversion
TIME
SPECIAL
SCREEN
• White Wash :
White Wash removes permanent images from the screen.
Note: An excessive permanent image may be impossible to clear entirely with White
Wash.
• Orbiter :
Orbiter may help prevent ghost images. However, it is best not to allow any fixed
image to remain on the screen. To avoid a permanent image on the screen, the
screen will move every 2 minutes.
• Inversion :
This is the function to invert the panel colour of the screen. The panel colour is automatically inverted every 30 minutes.
PIP/DW
Menu Prev.
4. Press the EXIT button to return to normal TV viewing.
Owner’s Manual 27
Operation
Special Menu Options
Low Power
- This is the function to reduce the power consumption of the set.
1. Press the MENU button and then use
D /E
button to select the SPECIAL menu.
2. Press the
G
button and then use
D /E
button to select Low power.
3. Press the
G
button and then use
D /E
button to select On or Off.
STATION
PICTURE
SOUND
Language
Child lock
ISM Method
Lowpower
power
Low
Set ID
Demo
G
On
Off
TIME
4. Press the EXIT button to return to normal TV viewing.
SPECIAL
SCREEN
PIP/DW
Menu Prev.
Demo
- Use it to see the difference between XD demo on and XD Demo off.
- It’s not available to use this function in RGB[PC], HDMI[PC] mode.
1. Press the MENU button and then use
D /E
2. Press the
G
button and then use
3. Press the
G
button to begin XD Demo.
D /E
button to select the SPECIAL menu.
button to select XD Demo.
STATION
PICTURE
SOUND
Language
Child lock
ISM Method
Low power
Set ID
Demo
Demo
TIME
4. To stop XD Demo, press the EXIT button.
SPECIAL
SCREEN
PIP/DW
28 PLASMA TV
Menu Prev.
G
To start
Operation
ENGLISH
Screen Menu Options
Auto Configure
- Automatically adjusts picture position and minimizes image shaking.
- This function works in the following mode : RGB[PC].
1. Press the MENU button and then use
2. Press the
G
button and then use
D
D
E
button to select the SCREEN menu.
button to select Auto config..
E
/
/
3. Press the G button to start Auto config..
• When Auto config. has finished, Ok will be shown on screen.
• If the position of the image is still not correct, try Auto adjustment again.
4. If picture needs to be adjusted more after Auto adjustment in RGB (PC), you can adjust
the Manual Config..
STATION
PICTURE
SOUND
TIME
SPECIAL
Auto config.
config.
Auto
Manual config.
VGA Mode
ARC
Zoom +/Position
Cinema
NR
Reset
G
To set
SCREEN
PIP/DW
Menu Prev.
5. Press the EXIT button to return to normal TV viewing.
- Although the image is still not correct, your set is functioning properly but needs further adjustment.
- The Auto config. functions don’t need to be run for HDMI mode.
Manual Configure
- If the picture isn’t clear after auto adjustment and especially that characters are still trembling, adjust the picture
phase manually.
- To correct the screen size, adjust Clock.
- This function works in the following mode : RGB[PC], RGB[DTV], COMPONENT (480p/576p/720p/1080i), HDMI
(480p/576p/720p/1080i).
- It’s not available to use Phase, Clock function in RGB[DTV], COMPONENT (480p/576p/720p/1080i), HDMI
(480p/576p/720p/1080i) mode.
1. Press the MENU button and then
2. Press the
G
button and then
D
/
3. Press the
G
button and then
D
/
D
E
E
/
E
button to select the SCREEN menu.
button to select Manual config..
button to select Phase, Clock, H-Position or
STATION
PICTURE
SOUND
TIME
V-Position.
SPECIAL
4. Press the
F
/
G
button to make appropriate adjustments.
5. Press the EXIT button to return to normal TV viewing.
Auto config.
Manualconfig.
config.
Manual
VGA Mode
ARC
Zoom +/Position
Cinema
NR
Reset
G
Phase
0
Clock
0
H-Position
0
V-Position
0
SCREEN
PIP/DW
Menu Prev.
Selecting Wide VGA/XGA mode
- To see a normal picture, match the resolution of RGB mode and selection of VGA/XGA mode.
- In some models, it’s not available to selection of XGA mode.
- This function works in the following mode : RGB[PC].
1. Press the MENU button and then use
2. Press the
G
button and then use
D /E
3. Press the G button and then use D
/E
button to select the SCREEN menu.
STATION
button to select VGA Mode (or XGA Mode).
PICTURE
D /E
button to select the desired VGA/XGA resolution.
SOUND
TIME
4. Press the EXIT button to return to normal TV viewing.
SPECIAL
Auto config.
Manual config.
Mode
VGA Mode
ARC
Zoom +/Position
Cinema
NR
Reset
G
640x480
848x480
852x480
SCREEN
PIP/DW
Menu Prev.
Owner’s Manual 29
Operation
Screen Menu Options
Setting Picture Format
- You can watch the screen in various picture formats; Spectacle, Full (option), Original, 4:3, 16:9 (Wide), 14:9 and
Zoom.
1. Press the MENU button and then use
2. Press the
G
button and then use
D
3. Press the G button and then use
Original, 4:3, 16:9, 14:9 or Zoom.
D
E
/
/
E
button to select the SCREEN menu.
button to select ARC.
D / E
button to select Spectacle, Full (option),
STATION
PICTURE
SOUND
TIME
SPECIAL
• Spectacle
When your TV receives the wide screen signal, following selection will lead you to adjust
the picture horizontally, in non-linear proportion, to fill the entire screen.
Auto config.
Manual config.
VGA Mode
ARC
ARC
G
Zoom +/Position
Cinema
NR
Reset
Spectacle
Full
Original
4:3
16:9
14:9
Zoom
SCREEN
PIP/DW
Menu Prev.
• Full (option)
When your TV receives the wide screen signal, following selection will lead you to adjust
the picture horizontally or vertically, in a linear proportion, to fill the entire screen fully.
• Original
When your TV receives the wide screen signal, it will be automatically changed to the
picture format to be sent.
• 4:3
Following selection will lead you to view a picture with an original 4:3 aspect ratio, with
gray bars appearing at both the left and right sides.
• 16:9 (Wide)
Following selection will lead you to adjust the picture horizontally, in a linear proportion,
to fill the entire screen (useful for viewing 4:3 formatted DVDs).
• 14:9
You can enjoy the picture format of 14:9 or general TV programme through the 14:9
mode. The screen 14:9 is viewed just like that the screen 4:3 is magnified to the left /
right.
• Zoom
Following selection will lead you to view the picture without any alternation, while filling
the entire screen. However, the top and bottom portions of the picture will be cropped.
4. Press the EXIT button to return to normal TV viewing.
-
You can only select 4:3 and 16:9 (Wide) in RGB[PC], HDMI[PC] mode only.
You can only select 4:3, 16:9 (Wide) and Zoom in RGB[DTV], HDMI[DTV], Component [DTV] mode only.
You can only select Spectacle, Full (option), 4:3, 16:9 (Wide), 14:9 and Zoom in Component [480i/576i] mode only.
There might be uncomfortable in full mode. Then change into other mode.
Picture Size Zoom
- When enlarging or reducing the picture, the screen may be display unnatural picture.
1. Press the MENU button and then
D
2. Press the
G
button and then
D
/
E
3. Press the
G
button and then
F
/
G
/
E
button to select the SCREEN menu.
button to select Zoom +/-.
button to make appropriate adjustments.
STATION
PICTURE
SOUND
TIME
4. Press the EXIT button to return to normal TV viewing.
SPECIAL
Auto config.
Manual config.
VGA Mode
ARC
Zoom +/+/Zoom
Position
Cinema
NR
Reset
SCREEN
PIP/DW
30 PLASMA TV
Menu Prev.
100
G
F
%
G
ENGLISH
Operation
Screen Position
- You are available to this function after adjusting Zoom In/Out.
1. Press the MENU button and then
D
2. Press the
G
button and then
D
/
E
3. Press the
G
button and then
D
/
E
E
/
button to select the SCREEN menu.
button to select Position.
or
F
/
G
button to adjust the position.
STATION
PICTURE
SOUND
TIME
4. Press the EXIT button to return to normal TV viewing.
SPECIAL
Auto config.
Manual config.
VGA Mode
ARC
Zoom +/Position
Position
D
G
F
G
E
Cinema
NR
Reset
SCREEN
PIP/DW
Menu Prev.
Cinema
- When you watch the movie, this function adjusts the set to the best picture appearance.
- This function works in the following mode:
TV, AV1, AV2, S-Video2, AV3, AV4, AV5 or COMPONENT 480i/576i.
1. Press the MENU button and then use
D /E
2. Press the
G
button and then use
D
/
E
button to select Cinema.
button to select the SCREEN menu.
3. Press the
G
button and then use
D
/
E
button to select On or Off.
4. Press the EXIT button to return to normal TV viewing.
STATION
TIME
Auto config.
Manual config.
VGA Mode
ARC
Zoom +/Position
Cinema
Cinema
SPECIAL
NR
Reset
PICTURE
SOUND
G
On
Off
G
3D NR
0
MPEG NR
0
SCREEN
PIP/DW
Menu Prev.
NR (Noise Reduction)
- You can select 3D NR or MPEG NR to reduce the picture noise which may appear on the screen during watching
the TV.
- This function is not available for use in RGB[PC[, HDMI[PC] mode.
- 3D NR is not available for use in RGB, HDMI, Component[DTV] mode.
1. Press the MENU button and then use
D /E
button to select the SCREEN menu.
2. Press the G button and then use
D /E
button to select NR.
3. Press the G button and then use
D /E
button to select 3D NR or MPEG NR.
STATION
PICTURE
SOUND
TIME
4. Press the
F
/
G
button to make appropriate adjustments.
5. Press the EXIT button to return to normal TV viewing.
SPECIAL
Auto config.
Manual config.
VGA Mode
ARC
Zoom +/Position
Cinema
NR
Reset
SCREEN
PIP/DW
Menu Prev.
Initializing (Reset to original factory value)
This function operates in current mode.
To initialize the adjusted value
1. Press the MENU button and then
2. Press the
G
button and then
3. Press the
G
button.
D
/
D
E
/
E
button to select the SCREEN menu.
button to select Reset.
STATION
PICTURE
SOUND
TIME
• You can initialize Phase, Clock, H-Position, V-Position, Position, Zoom +/-, PIP size,
PIP position, PIP Transparency and sub picture size of twin picture.
SPECIAL
Auto config.
Manual config.
VGA Mode
ARC
Zoom +/Position
Cinema
NR
Reset
G
To set
SCREEN
PIP/DW
Menu Prev.
Owner’s Manual 31
Operation
PIP (Picture-in-Picture) Feature
- PIP lets you view 2 different inputs (sources) on your set screen at the same time.
- It’s not available to use this function in TELETEXT mode.
Watching PIP
Press the PIP button to show the sub picture.
• Each press of PIP button changes the screen display as shown below.
RGB
AV1
RGB
AV1
RGB
AV1
10:30
10:30
10:30
RGB
AV1
RGB
10:30
10:30
Note :
a. When the sub picture size is 1/2 of the main picture, the picture quality might get poor.
b. The motion of the sub picture can be unnatural because the set displays full screen by synchronizing the main picture source when the
refresh rate between the main picture source and the sub picture source is different in PIP mode.
Programme Selection for Sub Picture
Moving the PIP (PIP mode only)
Press the PIP PR + /- button to select a programme for the sub
picture.
Press the POSITION button.
Repeatedly press the D / E or
F / G button until desired position is achieved. The sub picture moves up/down or
left/right.
Selecting an Input Signal Source for the PIP
Press the PIP INPUT button
to select the input source for
the sub picture.
Win. position
D
F
G
E
RGB
AV1
10:30
In some models, when the
sub picture quality get poor
for sub picture, select Auto,
PAL, SECAM or NTSC in
PIP System menu.
Picture Size
Press the SIZE button and
then F / G button to adjust
the sub picture size.
POP (Picture-out-of-Picture: Channel Scan)
Use POP to search the programmes of all the memorized channels one-by-one on the 3 PIP screen display, (while the main
picture source remains the current channel). The pictures of all
the programmed channels are searched with the 3 POP screen.
With SIZE button in DW1,
DW2 modes, main and sub
picture is adjusted simultaneously. With SIZE button in PIP
mode, sub picture is adjusted.
Win. size
F
G
Adjusting the screen for the PIP
Adjusting PIP Transparency (PIP mode only)
1. Press the MENU button and then
PIP/DW menu.
2. Press the
G
button and then
D
D
/
/
E
E
button to select the
button to select PIP
Transparency.
3. Press the
parency.
G
button and then
F
/
G
button to adjust PIP trans-
4. Press the EXIT button to return to normal TV viewing.
32 PLASMA TV
- In TV or AV modes for the main picture and RGB[PC] for the
sub picture, you can use Auto config and Manual config to
adjust the screen of the sub picture.
- In TV or AV modes for main picture and HDMI[DTV] or
Component 480p, 576p, 720p, 1080i for the sub picture, you
can use Manual config to adjust the screen of the sub picture.
Teletext (option)
- Teletext (or TOP text) is an optional function, therefore only the set with the teletext system can receive the teletext
broadcast.
- Teletext is a free service broadcast by most TV stations which gives up-to-the-minute information on news, weather,
television programmes, share prices and many other topics.
- The teletext decoder of this set can support the SIMPLE, TOP and FASTEXT systems. SIMPLE (standard teletext)
consists of a number of pages which are selected by directly entering the corresponding page number. TOP and FASTEXT are more modern methods allowing quick and easy selection of teletext information.
Switch on/off
Press the TEXT/ button to switch to teletext.
• The initial page or last page appears on the screen.
Two page numbers, TV station name, date and time are displayed on the screen headline. The first page number indicates your selection, while the second shows the current
page displayed.
Press the TEXT/ button to switch off teletext.
*
*
SIMPLE Text (option)
Page selection
1. Enter the desired page number as a three digit number with the NUMBER buttons. If
during selection you press a wrong number, you must complete the three digit number
and then reenter the correct page number.
2. The PR D / E button can also be used to select the preceding or following page.
Programming a colour button in LIST mode
If the TV is in SIMPLE text, TOP text or FASTEXT mode, press the
LIST mode.
M
button to switch to
Four teletext page numbers of your choice can be colour coded and easily selected by
pressing the corresponding coloured button on the remote control handset.
1. Press a coloured button.
2. Using the NUMBER buttons, select the page you wish to programme.
3. Press the OK button. The selected page is stored as the selected page number, blinking once to confirm this. From now on, you can select this page with the same coloured
button.
4. The three other coloured buttons are programmed in this way.
TOP Text (option)
The user guide displays four fields-red, green, yellow and blue at the bottom of the screen.
The yellow field denotes the next group and the blue field indicates the next block.
Block / group / page selection
1. With the blue button you can progress from block to block.
2. Use the yellow button to proceed to the next group with automatic overflow to the next
block.
3. With the green button you can proceed to the next existing page with automatic overflow to the next group. (Alternatively the PR D button can be used.)
4. The red button permits to return to previous selection. (Alternatively the PR E button
can be used.)
Direct page selection
Corresponding to the SIMPLE text mode, you can select a page by entering it as a three
digit number using the NUMBER buttons in TOP mode.
Owner’s Manual 33
ENGLISH
Operation
Operation
FASTEXT
The teletext pages are colour coded along the bottom of the screen and are selected by
pressing the corresponding coloured button.
Page selection
1. Press the i button to select the index page.
2. You can select the pages which are colour coded along the bottom line with the same
coloured buttons.
3. Corresponding to the SIMPLE text mode, you can select a page by entering its three
digit page number with the NUMBER buttons in FASTEXT mode.
4. The PR D / E button can also be used to select the preceding or following page.
Special Teletext Functions
REVEAL
Press this button to display concealed information, such as solutions of riddles or
puzzles.
Press this button again to remove the information from the display.
SIZE
Selects double height text.
Press this button to enlarge the top half of the page.
Press this button again to enlarge the bottom half of the page.
Press this button again to return to the normal display.
UPDATE
Displays the TV picture on the screen while waiting for the new teletext page.
Press this button to view the updated teletext page.
HOLD
Stops the automatic page change which will occur if a teletext page consists of 2 or
more sub pages. The number of sub pages and the sub page displayed is, usually,
shown on the screen below the time. When this button is pressed the stop symbol
is displayed at the top left-hand corner of the screen and the automatic page
change is inhibited.
To continue press this button again.
MIX
Displays the teletext pages superimposed on the TV picture.
To switch the TV picture off press this button again.
TIME
This button has two functions:
a) When viewing a TV programme, press this button to display the time at the top
right hand corner of the screen. Press this button again to remove the display.
b) In teletext mode, press this button to select a sub page number. The sub page
number is displayed at the bottom of the screen. To hold or change the sub page,
press the RED/ GREEN or PR D / E buttons. Press this button again to exit this
function.
34 PLASMA TV
Miscellaneous
ENGLISH
External Control Device Setup
- Connect the RS-232C input jack to an external control device (such as a computer or an A/V control system)
and control the set’s functions externally.
How to connect external control equipment
• Connect the serial port of the control device to the RS-232C jack on the Monitor back panel.
• RS-232C connection cables are not supplied with the set.
• The set remote control and front panel controls (except main power) will not be functional if the Monitor is controlled by a PC
computer or other external device.
< Back panel of the set >
VIDEO
AUDIO
L
HDMI/
DVI(VIDEO)
AUDIO INPUT
AV1
R
AUDIO
COMPONENT
RGB INPUT
L
VARIABLE
V
ARIABLE
AUDIO OUT
RS-232C INPUT
REMOTE
CONTROL
(CONTROL/SERVICE)
R
AV2
AV4
AV3
L
S-VIDEO VIDEO
R
(MONO)
AUDIO
Type of connector; D-Sub 9-pin male
No.
1
2
3
4
5
6
7
8
9
1
Pin name
No connection
RXD (Receive data)
TXD (Transmit data)
DTR (DTE side ready)
GND
DSR (DCE side ready)
RTS (Ready to send)
CTS (Clear to send)
No Connection
5
9
6
RS-232C configurations
3-wire configuration
(Not standard)
7-wire configuration
(Standard RS-232C cable)
RXD
TXD
GND
DTR
DSR
RTS
CTS
PC
PDP
2
3
5
4
6
7
8
3
2
5
6
4
8
7
D-Sub 9
D-Sub 9
TXD
RXD
GND
DSR
DTR
CTS
RTS
RXD
TXD
GND
DTR
DSR
RTS
CTS
PC
PDP
2
3
5
4
6
7
8
3
2
5
4
6
7
8
D-Sub 9
D-Sub 9
TXD
RXD
GND
DTR
DSR
RTS
CTS
Owner’s Manual 35
Miscellaneous
Set ID
- Use this function to specify a set ID number.
- Refer to ‘Real Data Mapping 1’. See page 40.
1. Press the MENU button and then use the
2. Press the
button and then use
D /E
3. Press the G button and then use
monitor ID number.
F /G
G
D /E
button to select the SPECIAL menu.
button to select Set ID.
STATION
PICTURE
button to adjust Set ID to choose the desired
SOUND
Language
Child lock
ISM Method
Low power
Set ID
G
1
Demo
TIME
SPECIAL
• The adjustment range of Set ID is 1 ~ 99.
SCREEN
4. Press the EXIT button to return to normal TV viewing.
PIP/DW
MENU Prev.
Communication Parameters
• Baud rate : 9600 bps (UART)
• Data length : 8 bits
• Parity : None
* Use a crossed (reverse) cable.
• Stop bit : 1 bit
• Communication code : ASCII code
Command Reference List
COMMAND 1 COMMAND 2
DATA
(Hexadecimal)
01. Power
02. Input Select
03. Aspect Ratio
04. Screen Mute
05. Volume Mute
06. Volume Control
07. Contrast
08. Brightness
09. Colour
10. Tint (option)
11. Sharpness
12. OSD Select
13. Remote control lock mode
14. PIP/DW
15. PIP Position
16. Treble
17. Bass
18. Balance
19. Colour Temperature (CSM)
20. Red Adjustment
21. Green Adjustment
22. Blue Adjustment
23. PIP input Source
24. Abnormal Status
25. ISM Method
26. Low Power
27. Orbiter Time Setting
28. Orbiter Pixel Setting
29. Picture Size
30. Auto Configure
31. Programme selection
32. Key
33. Input select (Main)
34. Input select (PIP)
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
k
j
j
j
j
j
j
m
m
x
x
a
b
c
d
e
f
g
h
i
j
k
l
m
n
q
r
s
t
u
v
w
$
y
z
p
q
r
s
t
u
a
c
b
y
0~1
0~9
Refer to p. 37
0~1
0~1
0 ~ 64
0 ~ 64
0 ~ 64
0 ~ 64
0 ~ 64
0 ~ 64
0~1
0~1
Refer to p. 38
0~3
0 ~ 64
0 ~ 64
0 ~ 64
0~3
0 ~ 50
0 ~ 50
0 ~ 50
0~9
0~a
0~3
0~1
1 ~ FE
1~3
0 ~ 20
1
0~63
Key Code
Refer to p. 41
Refer to p. 41
* When setting the 23 ~ 32, a menu doesn’t display on screen.
36 PLASMA TV
Transmission / Receiving Protocol
Transmission
[Command1][Command2][ ][Set ID][ ][Data][Cr]
* [Command 1]
* [Command 2]
* [Set ID]
* [DATA]
* [Cr]
* [ ]
: First command to control PDP set.
(j or k)
: Second command to control PDP set.
: You can adjust the set ID to choose
desired monitor ID number in special
menu.
Adjustment range is 1 ~ 99.
When selecting Set ID ‘0’, every
connected PDP set is controlled.
Set ID is indicated as decimal (1~99) on
menu and as Hexa decimal (0x0~0x63)
on transmission/receiving protocol.
: To transmit command data.
Transmit ‘FF’ data to read status of
command.
: Carriage Return
ASCII code ‘0x0D’
: ASCII code ‘space (0x20)’
OK Acknowledgement
[Command2][ ][Set ID][ ][OK][Data][x]
* The Monitor transmits ACK (acknowledgement) based on
this format when receiving normal data. At this time, if the
data is data read mode, it indicates present status data. If
the data is data write mode, it returns the data of the PC
computer.
Error Acknowledgement
[Command2][ ][Set ID][ ][NG][Data][x]
* The Monitor transmits ACK (acknowledgement) based on
this format when receiving abnormal data from
non-viable functions or communication errors.
Data 1: Illegal Code
2: not support function
3: Wait more time
01. Power (Command 2 : a)
04. Screen Mute (Command 2 : d)
G To control Power On/Off of the TV.
G To select screen mute on/off.
Transmission
Transmission
[k][d][ ][Set ID][ ][Data][Cr]
[k][a][ ][Set ID][ ][Data][Cr]
Data 0 : Power Off
1 : Power On
Ack
Data 0 : Screen mute off (Picture on)
1 : Screen mute on (Picture off)
Ack
[d][ ][Set ID][ ][OK][Data][x]
[a][ ][Set ID][ ][OK][Data][x]
G To show Power On/Off.
Transmission
05. Volume Mute (Command 2 : e)
[k][a][ ][Set ID][ ][FF][Cr]
G To control volume mute on/off.
You can also adjust mute using the MUTE button on
remote control.
Transmission
Ack
[a][ ][Set ID][ ][OK][Data][x]
* In like manner, if other functions transmit ‘0xFF’ data
based on this format, Acknowledgement data feed back
presents status about each function.
[k][e][ ][Set ID][ ][Data][Cr]
Data 0 : Volume mute off (Volume on)
1 : Volume mute on (Volume off)
Ack
02. Input Select (Command 2 : b)
[e][ ][Set ID][ ][OK][Data][x]
G To select input source for the TV.
You can also select an input source using the INPUT
SELECT button on the Monitor's remote control.
06. Volume Control (Command 2 : f)
G To adjust volume.
You can also adjust volume with the volume buttons
on remote control.
Transmission
[k][b][ ][Set ID][ ][Data][Cr]
Data 0
1
2
3
4
: TV
: AV1
: AV2
: S-Video2
: AV3
5
6
7
8
9
: AV4
: AV5
: Component
: RGB
: HDMI
Ack
Transmission
[k][f][ ][Set ID][ ][Data][Cr]
Data Min : 0 ~ Max : 64
* Refer to ‘Real data mapping 1’. See page 40.
Ack
[f][ ][Set ID][ ][OK][Data][x]
[b][ ][Set ID][ ][OK][Data][x]
07. Contrast (Command 2 : g)
03. Aspect Ratio (Command 2 : c) (Main Picture Size)
G To adjust the screen format. (Main picture format)
You can also adjust the screen format using the ARC
(Aspect Ratio Control) button on remote control or in the
SCREEN menu.
Transmission
[k][c][ ][Set ID][ ][Data][Cr]
Data 1
2
3
4
:
:
:
:
Normal screen (4:3)
Wide screen (16:9)
Spectacle
Full screen (Zoom)
6 : Original
7 : Wide screen (14:9)
8 : Full (Option)
Ack
[c][ ][Set ID][ ][OK][Data][x]
* Using the PC input, you select either 16:9 or 4:3 screen
aspect ratio.
G To adjust screen contrast.
You can also adjust contrast in the PICTURE menu.
Transmission
[k][g][ ][Set ID][ ][Data][Cr]
Data Min : 0 ~ Max : 64
* Refer to ‘Real data mapping 1’. See page 40.
Ack
[g][ ][Set ID][ ][OK][Data][x]
08. Brightness (Command 2 : h)
G To adjust screen brightness.
You can also adjust brightness in the PICTURE menu.
Transmission
[k][h][ ][Set ID][ ][Data][Cr]
Data Min : 0 ~ Max : 64
* Refer to ‘Real data mapping 1’. See page 40.
Ack
[h][ ][Set ID][ ][OK][Data][x]
Owner’s Manual 37
ENGLISH
Miscellaneous
Miscellaneous
09. Colour (Command 2 : i)
14. PIP / DW (Command 2 : n)
G To adjust the screen colour.
You can also adjust colour in the PICTURE menu.
G To control the PIP (Picture In picture)/DW.
You can also control the PIP/DW using the PIP button on
the remote control or in the PIP/DW menu.
Transmission
[k][i][ ][Set ID][ ][Data][Cr]
Transmission
Data Min : 0 ~ Max : 64
* Refer to ‘Real data mapping 1’. See page 40.
Ack
[i][ ][Set ID][ ][OK][Data][x]
10. Tint (Command 2 : j) (option)
[k][n][ ][Set ID][ ][Data][Cr]
Data 0: PIP/DW off
1: PIP
2: DW1
Ack
3: DW2
5: POP
[n][ ][Set ID][ ][OK][Data][x]
G To adjust the screen tint.
You can also adjust tint in the PICTURE menu.
Transmission
[k][j][ ][Set ID][ ][Data][Cr]
15. PIP Position (Command 2 : q)
Data Red : 0 ~ Green : 64
* Refer to ‘Real data mapping 1’. See page 40.
Ack
G To select sub picture position for PIP.
You can also adjust the sub picture position using POSITION button on the remote control or in the PIP/DW menu.
[j][ ][Set ID][ ][OK][Data][x]
Transmission
11. Sharpness (Command 2 : k)
Data 0
1
2
3
Ack
[k][q][ ][Set ID][ ][Data][Cr]
G To adjust the screen sharpness.
You can also adjust sharpness in the PICTURE menu.
Transmission
[k][k][ ][Set ID][ ][Data][Cr]
:
:
:
:
Right down on screen
Left down on screen
Left up on screen
Right up on screen
[q][ ][Set ID][ ][OK][Data][x]
Data Min : 0 ~ Max : 64
* Refer to ‘Real data mapping 1’. See page 40.
Ack
[k][ ][Set ID][ ][OK][Data][x]
16. Treble (Command 2 :r)
12. OSD Select (Command 2 : l)
G To select OSD (On Screen Display) on/off when controlling remotely.
G To adjust treble.
You can also adjust treble in the SOUND menu.
Transmission
[k][r][ ][Set ID][ ][Data][Cr]
Transmission
[k][l][ ][Set ID][ ][Data][Cr]
Data 0 : OSD off
1 : OSD on
Ack
Data Min : 0 ~ Max : 64
* Refer to ‘Real data mapping 1’. See page 40.
Ack
[r][ ][Set ID][ ][OK][Data][x]
[l][ ][Set ID][ ][OK][Data][x]
13. Remote control lock mode (Command 2 : m)
G To lock the front panel controls on the monitor and remote
control.
Transmission
[k][m][ ][Set ID][ ][Data][Cr]
Data 0 : Lock off
G To adjust bass.
You can also adjust bass in the SOUND menu.
Transmission
1 : Lock on
Ack
[m][ ][Set ID][ ][OK][Data][x]
* If you’re not using the remote control, use this mode.
When main power is on/off, external control lock is
released.
38 PLASMA TV
17. Bass (Command 2 : s)
[k][s][ ][Set ID][ ][Data][Cr]
Data Min : 0 ~ Max : 64
* Refer to ‘Real data mapping 1’. See page 40.
Ack
[s][ ][Set ID][ ][OK][Data][x]
18. Balance (Command 2 : t)
23. PIP Input Select (Command 2 : y)
G To adjust balance.
You can also adjust balance in the SOUND menu.
G To select input source for sub picture in PIP/DW picture mode. You can also adjust input source for sub
picture using PIP INPUT button on remote control.
Transmission
[k][t][ ][Set ID][ ][Data][Cr]
Transmission
Data Min : 0 ~ Max : 64
* Refer to ‘Real data mapping 1’. See page 40.
Ack
[k][y][ ][Set ID][ ][Data][Cr]
[t][ ][Set ID][ ][OK][Data][x]
Data 0
1
2
3
4
Ack
: TV
: AV1
: AV2
: S-Video2
: AV3
19. Colour Temperature (Command 2 : u)
[y][ ][Set ID][ ][OK][Data][x]
5
6
7
8
9
: AV4
: AV5
: Component
: RGB
: HDMI
G To adjust colour temperature.
You can also adjust CSM in the PICTURE menu.
24. Abnormal State (Command 2 : z)
Transmission
[k][u][ ][Set ID][ ][Data][Cr]
Data 0: Cool
1: Normal
G To recognize an abnormal state.
2: Warm
3: User
Transmission
Ack
[k][z][ ][Set ID][ ][FF][ ][Cr]
[u][ ][Set ID][ ][OK][Data][x]
Data FF : Read
Ack
[z][ ][Set ID][ ][OK][Data][x]
20. Red Adjustment (Command 2 : v)
G To adjust red in colour temperature.
Transmission
[k][v][ ][Set ID][ ][Data][Cr]
Data Min : 0 ~ Max : 50
* Refer to ‘Real data mapping 2’. See page 40.
Ack
[v][ ][Set ID][ ][OK][Data][x]
Data 0: Normal (Power on and signal exist)
1: No signal (Power on)
2: Turn the TV off by remote control
3: Turn the TV off by sleep time function
4: Turn the TV off by RS-232C function
5: 5V down
6: AC down
7: Turn the TV off by Fan Alarm function (option)
8: Turn the TV off by Off time function
9: Turn the TV off by Auto sleep function
a: Turn the TV off by AV board detect
* This function is “read only”.
21. Green Adjustment (Command 2 : w)
G To adjust green in colour temperature.
Transmission
[k][w][ ][Set ID][ ][Data][Cr]
Data Min : 0 ~ Max : 50
* Refer to ‘Real data mapping 2’. See page 40.
Ack
[w][ ][Set ID][ ][OK][Data][x]
25. ISM Method
(Command 1 : j, Command 2 : p)
G To control the ISM method. You can also adjust ISM
Method in SPECIAL menu.
Transmission
[j][p][ ][Set ID][ ][Data][Cr]
Data 0 : Normal Mode
1 : White Wash
22. Blue Adjustment (Command 2 : $)
Ack
G To adjust blue in colour temperature.
[p][ ][Set ID][ ][OK][Data][x]
2 : Orbiter
3 : Inversion
Transmission
[k][$][ ][Set ID][ ][Data][Cr]
Data Min : 0 ~ Max : 50
* Refer to ‘Real data mapping 2’. See page 40.
Ack
[$][ ][Set ID][ ][OK][Data][x]
Owner’s Manual 39
ENGLISH
Miscellaneous
Miscellaneous
26. Low Power
(Command 1 : j, Command 2 : q)
G To reduce the power consumption of the monitor. You
can also adjust Low Power in SPECIAL menu.
Transmission
30. Auto Configure
(Command 1 : j, Command 2 : u)
G To adjust picture position and minimize image shaking
automatically. It works only in RGB (PC) mode.
Transmission
[j][q][ ][Set ID][ ][Data][ ][Cr]
[j][u][ ][Set ID][ ][Data][Cr]
Data 0 : Off
1 : On
Data 1: To set
Ack
[u][ ][Set ID][ ][OK][Data][x]
Ack
[q][ ][Set ID][ ][OK][Data][x]
27. Orbiter Time Setting
(Command 1 : j, Command 2 : r)
G To adjust orbiter operation time term.
Transmission
[j][r][ ][Set ID][ ][Data][ ][Cr]
Data Min: 1 ~ Max: FE
* Refer to ‘Real data mapping 1’.
Ack
[r][ ][Set ID][ ][OK][Data][x]
31. Programme selection
(Command 1 : m, Command 2 : a)
G To select a programme for the main picture.
Transmission
[m][a][ ][Set ID][ ][Data0][ ][Data1][ ][Data2][Cr]
Data0 Min: 0 ~ Max: 63 (0 ~ C7, 200Pr is on)
* Refer to ‘Real data mapping 1’.
Data1 Don’t care
Data2 0 : Main
1 : Sub
Ack
[a][ ][Set ID][ ][OK][Data0][x]
28. Orbiter Pixel Setting
(Command 1 : j, Command 2 : s)
G To adjust pixel number in orbiter function.
Transmission
[j][s][ ][Set ID][ ][Data][Cr]
* Real data mapping 1
Data Min: 1 ~ Max: 3
* Refer to ‘Real data mapping 1’.
0 : Step 0
Ack
A : Step 10 (Set ID 10)
[s][ ][Set ID][ ][OK][Data][x]
F : Step 15 (Set ID 15)
10 : Step 16 (Set ID 16)
64 : Step 100
29. Picture Size Setting for DW Mode
(Command 1 : j, Command 2 : t)
G To select the DW picture format.
You can also select the DW picture format using the
SIZE on the remote control.
Transmission
[j][t][ ][Set ID][ ][Data][Cr]
Data Min: 0 ~ Max: 20
* Refer to ‘Real data mapping 1’.
Ack
[t][ ][Set ID][ ][OK][Data][x]
40 PLASMA TV
6E : Step 110
73 : Step 115
74 : Step 116
C7 : Step 199
FE : Step 254
FF : Step 255
* Real data mapping 2
0 : -40
1 : -39
2 : -38
28 : 0
4E : +38
4F : +39
50 : +40
32. Key
(Command 1 : m, Command 2 : c)
34. Input select (Command 1 : x, Command 2 : y)
G To adjust input source for sub picture in PIP mode
G To send IR remote key code.
Transmission
Transmission
[x][y][ ][Set ID][ ][Data][Cr]
[m][c][ ][Set ID][ ][Data][Cr]
Data Structure
Data Key code - Refer to page 43.
Ack
MSB
[c][ ][Set ID][ ][OK][Data][x]
0
LSB
0
0
0
0
External Input
0
0
Input Number
External Input
Data
0
0
0
1
Analog
0
0
1
0
AV
G To select input source for TV
0
1
0
0
Component
Transmission
0
1
0
1
RGB-DTV
[x][b][ ][Set ID][ ][Data][Cr]
0
1
1
0
RGB-PC
Data Structure
1
0
0
1
HDMI
33. Input select (Command 1 : x, Command 2 : b)
(Main Picture Input)
MSB
0
0
LSB
0
0
0
0
External Input
0
0
Data
0
0
0
0
Input1
0
0
0
1
Input2
Data
0
0
1
0
Input3
Input Number
External Input
Input Number
0
0
0
0
1
Analog
0
0
1
1
Input4
0
0
1
0
AV
0
1
0
0
Input5
0
1
0
0
Component
0
1
0
1
Input6
0
1
0
1
RGB-DTV
0
1
1
0
RGB-PC
1
0
0
1
HDMI
Input Number
Ack
[y][ ][Set ID][ ][OK][Data][x]
Data
0
0
0
0
Input1
0
0
0
1
Input2
0
0
1
0
Input3
0
0
1
1
Input4
0
1
0
0
Input5
0
1
0
1
Input6
Ack
[b][ ][Set ID][ ][OK][Data][x]
Owner’s Manual 41
ENGLISH
Miscellaneous
Miscellaneous
IR Code (NEC Format)
How to connect
G Connect your wired remote control to the Remote Control port on the Monitor.
Remote Control IR Code (NEC Format)
G Output waveform
Single pulse, modulated with 37.917KHz signal at 455KHz
TC
Carrier frequency
FCAR = 1/TC = fOSC/12
Duty ratio = T1/TC = 1/3
T1
G Configuration of frame
• 1st frame
Lead
code
Low
custom code
High
custom code
Data code
Data code
C0 C1 C2 C3 C4 C5 C6 C7 C0 C1 C2 C3 C4 C5 C6 C7 D0 D1 D2 D3 D4 D5 D6 D7 D0 D1 D2 D3 D4 D5 D6 D7
• Repeat frame
Repeat code
Tf
G Lead code
9 ms
4.5 ms
0.55 ms
G Repeat code
9 ms
2.25 ms
G Bit description
• Bit “0”
• Bit “1”
0.56 ms
0.56 ms
1.12 ms
2.24 ms
G Frame interval : Tf
The waveform is transmitted as long as a key is depressed.
Tf
Tf
Tf=108ms @455KHz
42 PLASMA TV
Code (Hexa)
00
01
02
03
40
41
06
07
08
C4
C5
09
10
11
12
13
14
15
16
17
18
19
0B
98
BF
C6
D5
D6
5A
D0
D1
D2
CF
D3
1E
1A
0A
0E
43
44
4D
52
53
20
2A
22
24
26
62
64
65
70
60
61
63
71
72
5C
5D
79
76
77
AF
Function
PR+
PRVOL+
VOLD
E
G
F
POWER
POWER ON
POWER OFF
MUTE
Number Key 0
Number Key 1
Number Key 2
Number Key 3
Number Key 4
Number Key 5
Number Key 6
Number Key 7
Number Key 8
Number Key 9
INPUT
MULTIMEDIA
COMPONENT
HDMI
RGB
TV
AV1
AV2
AV3
AV4
AV5
S-Video2
FAVOURITE
Q.VIEW
I/II
SLEEP
MENU
OK( )
PSM
SSM
LIST
TEXT/
REVEAL
MODE
MIX
TIME
UPDATE / WIN.POSITION
SIZE / WIN.SIZE
HOLD
INDEX
PIP/DW
PIP INPUT
SWAP
PIP PR+
PIP PRZoom +
Zoom ARC
ARC (4:3)
ARC (16:9)
ARC (Zoom)
*
ENGLISH
Miscellaneous
Note
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button (Power On/Off)
Discrete IR Code (Only Power On)
Discrete IR Code (Only Power Off)
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
Discrete IR Code (Input COMPONENT Selection)
Discrete IR Code (Input HDMI Selection)
Discrete IR Code (Input RGB Selection)
Discrete IR Code (Input TV Selection)
Discrete IR Code (Input AV1 Selection)
Discrete IR Code (Input AV2 Selection)
Discrete IR Code (Input AV3 Selection)
Discrete IR Code (Input AV4 Selection)
Discrete IR Code (Input AV5 Selection)
Discrete IR Code (Input S-Video2 Selection)
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
R/C Button
Discrete IR Code (Only 4:3 mode)
Discrete IR Code (Only 16:9 mode)
Discrete IR Code (Only Zoom mode)
Owner’s Manual 43
Miscellaneous
Programming the Remote
G The remote is a multi-brand or a universal remote. It can be programmed to operate most remote-controllable devices of
other manufacturers.
Note that the remote may not control all models of other brands.
Programming a code into a remote mode
1. To find out whether your remote can operate the device without programming, turn on the device such as a VCR and
press the corresponding mode button on the remote.
After that, press the POWER button. If the device is turned off then it responds properly and the remote need not to
be programmed. If not, the remote should be programmed to operate the device. The programming procedures are
explained below.
2. Press the MENU and MUTE button continuously at the same time for 2 seconds, the current selected device button
will be illuminated.
If you don't press any button for 20 seconds, the light on the mode button will be turned off. In that case, you have to
repeat from step 2.
3. Enter code numbers using the number button on the remote by referring the code table on the following pages. When
pressing the button, the light blinks at a time. If the device turned off, the programming is successful.
4. Press the MENU button to store the code. After blinking twice, this code is stored.
5. Test the remote functions to see if the device responds properly. If not, repeat from step 2.
44 PLASMA TV
Miscellaneous
ENGLISH
Programming Codes
VCRs
Brand
Codes
Brand
Codes
Brand
Codes
Brand
Codes
AIWA
AKAI
034
016
125
072
031
012
035
028
108
003
031
005
065
112
108
012
034
059
006
029
036
129
003
034
031
107
132
012
004
043
031
031
012
040
043
012
048
130
KENWOOD
014
047
001
101
034
003
017
040
031
067
012
069
101
027
031
003
033
101
045
013
013
049
151
034
024
012
048
043
053
066
133
013
063
031
031
067
101
013
PORTLAND
PULSAR
QUARTZ
QUASAR
RCA
108
072
011
033
013
040
107
145
003
031
053
058
148
014
032
105
113
125
022
003
102
017
131
003
013
031
101
031
024
003
056
077
034
013
031
067
034
010
TATUNG
TEAC
TECHNICS
TEKNIKA
039
034
031
019
101
034
006
008
059
040
040
012
048
012
040
003
031
053
012
034
058
AMPRO
ANAM
AUDIO DYNAMICS
BROKSONIC
CANON
CAPEHART
CRAIG
CURTIS MATHES
DAEWOO
DAYTRON
DBX
DYNATECH
ELECTROHOME
EMERSON
FISHER
FUNAI
GE
GO VIDEO
HARMAN KARDON
HITACHI
INSTANTREPLAY
JCL
JCPENNY
JENSEN
JVC
043 046 124
146
033
023
037
031
103
039 043
129
033
040
033
007
108
116
135
041
010 064
110 111
117 119
023 039 043
053
027
035
101
153
010
LG (GOLDSTAR)
LLOYD
LXI
MAGIN
MAGNAVOX
MARANTZ
MARTA
MATSUI
MEI
MEMOREX
MGA
MINOLTA
MITSUBISHI
017
031
037
131
008
025
034
046
138
009
033
109
136
045
018
063
033
033
013
066
063 072
144 147
MTC
MULTITECH
NEC
026 034
137 150
NORDMENDE
OPTONICA
PANASONIC
PENTAX
015 033
101
031 033 043
050 055 060
150 152
PHILCO
PHILIPS
PILOT
PIONEER
034 039 043
048
012 013 020
106 114 123
009 013 014
034 101 106
033 034 041
068
031 033 067
030
033
010
034
102
046
020
020
051
REALISTIC
RICO
RUNCO
SALORA
SAMSUNG
014 031
053 072
134 139
059
045 046
059 061
040
034
023 039 043
054
070 074 083
140 145
020 031 033
034 067
033 034 054
071 101
021 048
SANSUI
SANYO
SCOTT
SEARS
SHARP
SHINTOM
SONY
SOUNDESIGN
STS
SYLVANIA
SYMPHONIC
TANDY
014
066
020
041
109
147
008
033
054
075
033
062
140
145
034
063
144
010 014
034 040
101
THOMAS
TMK
TOSHIBA
TOTEVISION
UNITECH
VECTOR RESEARCH
040 102 104
107 109 112
115 120 122
043 048 135
007 010 014
134
037 112 129
VICTOR
VIDEO CONCEPTS
VIDEOSONIC
WARDS
YAMAHA
ZENITH
043
039 043
033 070
031 033 034
013 042 047
082 112 131
101
034 046
013
033
054
034
048
072
017
034
131
039
056
080
024
040
043
101
008 009 010
014 017 020
042 073 081
054 149
009 031 052
057 058 076
078 149
033 034 059
034
CATV
CATV
Brand
Codes
Brand
Codes
ABC
003
046
112
014
005
026
092
007
007
065
080
019
023
020
057
032
072
008
052
GOLDEN CHANNEL
HAMLIN
HITACHI
HOSPITALITY
JERROLD
030
049
052
070
002
009
074
001
037
033
010
100
028
015
073
016
044
100
006
AJIN
ANTRONIK
ARCHER
CABLE STAR
CENTURION
CENTURY
CITIZEN
COLOUR VOICE
COMBANO
COMTRONICS
DIAMOND
EAGLE
EASTERN
ELECTRICORD
GE
GEMINI
GI
004 039 042
052 053
007 014 024
090
081
030
030 040
062 066
022 025 054
074
LG (GOLDSTAR)
M-NET
MACOM
MAGNAVOX
MEMOREX
MOVIE TIME
NSC
OAK
PANASONIC
PARAGON
PHILIPS
Brand
050 055
055
077
003 004 008
010 052 069
PIONEER
106 101 005
PULSAR
RCA
REGAL
REGENCY
REMBRANT
SAMSUNG
012 064 079
032
028 038 071
031 037 053
047
012 013 020
POST NEWS WEEK
PRUCER
PTS
SCIENTIFIC ATLANTA
SHERITECH
SIGNAL
SIGNATURE
SL MARX
Codes
Brand
Codes
065
034
076
016
059
011
073
100
047
049
057
025
102
003
043
022
030
052
030
SPRUCER
STARCOM
STARGATE
TADIRAN
TAEKWANG
TAIHAN
TANDY
TEXSCAN
TOCOM
TOSHIBA
UNIKA
UNITED CABLE
UNIVERSAL
047
002
008
030
110
105
017
029
039
100
007
004
005
026
012
087
100
085 090
051 052 063
048 071 072
074
050
107 030 068
011 041 042
045 046
VIEWSTAR
ZENITH
078
004 008 009
030
040 056
014
053
007
027
015
088
114
024
014
032
018
089
060
024
035
086
093
Owner’s Manual 45
Miscellaneous
Programming Codes
HDSTB
Brand
Codes
Brand
ALPHASTAR DSR
AMPLICA
BIRDVIEW
CHANNEL MASTER
123
050
051
013
036
008
054
050
005
011
141
024
038
093
097
122
089
114
017
133
GENERAL INSTRUMENT 003
031
HITACHI
139
HOUSTON TRACKER
033
057
HUGHES
068
JANIEL
060
JERROLD
061
KATHREIN
108
LEGEND
057
LG
001
LUTRON
132
LUXOR
062
MACOM
010
065
MEMOREX
057
NEXTWAVE
028
NORSAT
069
CHAPARRAL
CITOH
CURTIS MATHES
DRAKE
DX ANTENNA
ECHOSTAR
ELECTRO HOME
EUROPLUS
FUJITSU
126 129
014 015 018
055
009 012 077
145
006 007 010
052 112 116
046
040
094
098
056
057
095
099
076
058
096
100
021 022 027
Codes
Brand
134
004 016 029
059 101
140
037 039 051
104
147
144
059 063 064
124 125
070
Codes
143
PANASONIC
060
PANSAT
121
PERSONAL CABLE 117
PHILIPS
071
PICO
105
PRESIDENT
019
PRIMESTAR
030
PROSAT
072
RCA
066
REALISTIC
043
SAMSUNG
123
SATELLITE SERVICE CO 028
085
SCIENTIFIC ATLANTA
032
SONY
103
STARCAST
041
SUPER GUIDE
020
TEECOM
023
Brand
PACE SKY SATELLITE
142
TOSHIBA
UNIDEN
102
110 111
VIEWSTAR
WINEGARD
ZENITH
106
074
Codes
088
137
002
016
044
078
101
115
128
081
091
090 107 130
127
025
045
079
135
042 043
048 049
080 086
136
146
082 083 084
120
035 047 057
138
124 125
026 075 087
Audio
Brand
Codes
AIWA
014
125
230
AKAI
163
ANAM
003
059
217
BURMECTER
252
CARVER
086
CLARION
199
DAEWOO
027
102
DENON
015
FANTASIA
071
FINEARTS
022
FISHER
089
LG(GOLDSTAR)
001
087
190
211
HAITAI
034
HARMAN/KARDON 068
INKEL
037
078
122
152
157
189
225
247
028 070 096
129 139 229
014 017 023
106 189 216
235 236
Brand
Codes
JVC
KEC
KENWOOD
004
185
038
170
215
030
045
014
100
175
179
201
214
238
103
111
002
034
097
049
104
107
046
013
048
133
158
007
142
104
KOHEL
NAD
LOTTE
053 060 084
148 198 221
075 130 143
099
021
107
191
212
035
058
079
149
153
158
207
226
024
108
192
239
188
062
095
150
154
159
222
227
029
110
210
222
069
121
151
155
160
224
243
LXI
MAGNAVOX
MARANTZ
MCINTOSH
MCS
MEMOREX
NAD
ONKYO
OPTIMUS
PANASONIC
PENNEY
013
186
050
171
222
046
016
172
176
180
202
219
240
141
187
067 089
197 206
036
173
177
181
208
223
098
174
178
183
213
232
018 020 025
041 081 090
112
Brand
Codes
PHILIPS
PIONEER
026
039
065
115
113
080
092
103
124
193
204
011
019
106
031
072
156
206
005
044
118
012
076
162
166
205
QUASAR
RCA
RCX
REALISTIC
SAMSUNG
SANSUI
SANYO
SCOTT
SHARP
SHERWOOD
SONY
TAEKWANG
040 041 047
056 057 132
140
033 064 113
220 241 251
TEAC
TECHNICS
112
042
091
123
106
145
194
244
135
083
186
032
082
184
209
006
045
126
020
077
163
167
231
143
043 063
093 094
127 250
146
195
245
138
234
Brand
Codes
TOSHIBA
THE
VICTOR
WARDS
YAMAHA
147 218
137
061
088 131
089
054 055 066 092
199
182
203
246
144
051 052
117 119
199 200
158
109
248
073
105
164
168
233
114
249
074
161
165
169
242
010 085 106 136
185 187 237
101 113 128 134
DVD
Brand
Codes
Brand
Codes
Brand
Codes
Brand
Codes
APEX DIGITAL
DENON
GE
HARMAN KARDON
JVC
LG
022
020 014
005 006
027
012
001 010 016 025
MAGNAVOX
MARANTZ
MITSUBISHI
NAD
ONKYO
PANASONIC
013
024
002
023
008 017
003 009
PHILIPS
PIONEER
PROCEED
PROSCAN
RCA
SAMSUNG
013
004
021
005
005
011
SONY
THOMPSON
TOSHIBA
YAMAHA
ZENITH
007
005
019
009
010
46 PLASMA TV
026
006
006
015
006
008
018
016 025
Miscellaneous
ENGLISH
Notes
Owner’s Manual 47
Miscellaneous
Notes
48 PLASMA TV
Miscellaneous
ENGLISH
Notes
Owner’s Manual 49
Miscellaneous
Troubleshooting Checklist
• Check whether the set is turned on.
No picture &
No sound
• Power cord inserted into wall outlet?
• Plug another product’s power cord into the wall outlet where the set’s power
cord was plugged in.
• Press the VOLUME (G) button.
Picture OK &
No sound
• Sound muted? Press MUTE button.
• Check whether the TV speaker is “on” in the SOUND menu.
• Check to see if there is any object between the set and the remote control
causing obstruction.
The remote control
doesn’t work
• Check to see if the batteries are installed with the correct polarities.
(Refer to p.6)
• Check if the remote control handset is set up to correct mode.
• Install new batteries. (Refer to p.6)
Picture appears slowly,
after switching on
• This is normal as the image is muted during the startup process of the set.
Please contact your service centre, if the picture has not appeared after five
minutes.
• Select Colour in the PICTURE menu and press the VOLUME (G) button.
(Refer to p.23)
No or Poor colour
or Poor picture
• Keep a certain distance between the set and the VCR.
• Activate any function to restore the brightness of the picture.
(If still picture is on the screen for more than 5 minutes, the screen gets dark.)
Horizontal/vertical bars
or picture shaking
No output from one of the
speakers
Unusual sound from
inside the set
50 PLASMA TV
• Check for local interference such as an electrical appliance or power tool.
• Adjust Balance in the SOUND menu. (Refer to p.24)
• A change in ambient humidity or temperature may result in an unusual noise
at the time of switching off or on of the set and does not indicate a fault with
the set.
Miscellaneous
ENGLISH
Product Specifications
42PX4R
42PX4RV
42PX4RVA
42PX4R-ZA
42PX4RV-ZA
42PX4RVA-ZA
Width (inches / mm)
49.3 / 1252
49.3 / 1252
49.3 / 1252
Height (inches / mm)
27.78 / 705.5
27.78 / 705.5
27.8 / 706.5
Depth (inches / mm)
11.29 / 286.7
11.29 / 286.7
10.7 / 270.7
Weight (pounds / kg)
84.9 / 38.5
70.06 / 31.78
76.72 / 34.8
MODEL
Power requirement
AC100-240V, 50/60Hz
Operating Temperature Range
32 ~ 104°F (0 ~ 40°C)
Operating Humidity Range
Less than 80%
50PX4R
MODEL
•
50PX4R-ZA
Width (inches / mm)
55.1 / 1400
Height (inches / mm)
32.3 / 821
Depth (inches / mm)
3.9 / 99
Weight (pounds / kg)
115 / 52.15
Power requirement
AC100-240V, 50/60Hz
Operating Temperature Range
32 ~ 104°F (0 ~ 40°C)
Operating Humidity Range
Less than 80%
The specifications shown above may be changed without notice for quality improvement.
Owner’s Manual 51
Download PDF

advertising