Part No: 2920-5001
QS020 Issue 2 Copyright © 2012 TDSi
Introduction
2920-5001 is a high performance proximity card reader and digital keypad:
Dual relay outputs:
ZONE 1: lock operation, door status detection, egress button functions.
ZONE 2 doorbell/button functionality.
Capacity for 1000 passwords and card holders
(ZONE 1) and up to 10 passwords or card holders
(ZONE 2).
Built-in tamper function, watchdog timer, and a powerful reboot and self-recovery watchdog which can be connected to an external unlock button.
Can be operated for card access only, card or password access or combined access.
5cm read range.
Operates at 125kHz.
Specifications
Temperature range
Humidity range
Power
Current
Card Read Range
Operating
Frequency
Capacity
-20ºC to +50ºC
5-95% non-condensing
12 - 24V DC; 12- 24 V AC
80mA (standby); 110mA (working)
Up to 50 mm
125kHz
Dimensions
Weight
ZONE 1: 1000 passwords AND cards;
ZONE 2: 10 passwords OR cards
123 (H) x 79 (W) x 21 (D) mm
0.54kg
Mounting
1. Open the controller by removing the back case screw at the bottom with the supplied spline tool.
2. Use the screws provided to mount the back case to the wall. Be sure to draw the wiring through the large central hole in the back case, and keep level.
3. Use the provided template to accurately locate and drill the required holes.
4. Connect all wires as described opposite and on the labelling guide on the back of the unit.
5. Put the unit onto the back cover and fasten in place.
Connection
Colour Use
Red
Black
+ AC or DC input
̶ 12V – 24V
POWER IN
White
Aqua
Lock: Normally open
Lock: Normally closed
ZONE 1
Blue
Grey
Bell: Normally open
Bell: Normally closed
ZONE 2
Green Ground for door sense, egress button and doorbell button
GNDs
For technical assistance, contact TDSi Support:
Email: [email protected]
Phone: +44(0) 1202 724998
Settings
Settings Mode
To access the settings mode, enter the administrator’s code (default 1234) twice. The keypad emits a long beep and the mode LED turns green.
To exit settings mode, press #. The keypad automatically exits settings mode after 30s of inactivity
You can also use an administrator’s master card (see below) to enter and exit settings mode.
Set the Admin Password
Having entered settings mode, press * and then 3. The mode LED flashes green.
Enter a new password of the correct length (default: 4 digits). Type the password again to confirm. The keypad emits a long beep and the mode LED turns green.
Set the Password Length
NOTE: CHANGING THIS SETTING CLEARS ALL
EXISTING CARDS AND PASSWORDS
Having entered settings mode, press * and then 9. The mode LED flashes green. Press 0 and then 4.
Enter required length of code: 2 to 6.
Reset the Admin Password
Switch unit off. Switch on whilst holding down # key.
Code is 123456 truncated to set password admin code length (see above).
Set User Access Mode
Having entered settings mode, press * and then 0. The mode LED flashes green. Set the required mode as follows:
Card access only press 0 twice
Card or password access press 0 and then 1
Card AND password access press 0 and then 2
Enrol Zone 1 Users
Having entered settings mode, type the user’s 3-digit code (000-999). Red LED indicates number already in use, green LED: number available.
Enrol card: optional for Card or password access mode
Swipe user’s card. Single beep indicates that card has been read successfully.
Enrol password: not available in Card Access mode
Type a password for the user (set digit length).
Delete Zone 1 User
Having entered settings mode, type the user’s 3-digit code (000-999). Red LED indicates number exists.
Press * twice.
Assign Master Card
Having entered settings mode, press * and then 7.
Swipe card.
Delete Master Card
Having entered settings mode, press * and then 7.
Swipe card. Press * twice
Modify User Password
Having entered settings mode, press * and then 9.
Press 0 and then 2.
Input 3-digit user code, e.g. 005.
Enter new access code (of required length)
Enrol Zone 2 Users
Having entered settings mode, press * and then 4.
Type the user’s 2-digit code (00-99). Red LED indicates number already in use, green LED: number available.
Enrol card: optional for Card or password access mode
Swipe user’s card. Single beep indicates that card has been read successfully.
Enrol password: not available in Card Access mode
Type a password for the user (set digit length).
Delete Zone 2 User
Having entered settings mode, press * and then 4.
Type the user’s 2-digit code (00-99). Red LED indicates code is valid.
Press * twice.
Delete all Cards and Passwords
(BOTH Zones)
Having entered settings mode, press * and then 8. The mode LED flashes green.
Press 8 twice. The unit beeps four times.
Set Door Lock Time
(Zone 1 only)
Having entered settings mode, press * and then 1.
Set the unlock time in seconds: 00-99 (e.g. 05 = 5 seconds). With value of 00, user must lock door with second authentication.
Set Door Bell Time
(Zone 2 only)
Having entered settings mode, press * and then 5.
Set the operating time in seconds: 00-99 (e.g. 05 = 5 seconds).
Enable/Disable Anti-Tamper Alarm
Having entered settings mode, press * and then 6.
DISABLE: press 0 and then 1; ENABLE: press 0 and then
2.
NOTE. If alarm is activated (due to exposure of internal sensor to light), switch off buzzer by replacing cover (60s delay) or by entering admin code.
Enable/Disable Doorbell
(Zone 2 only)
Having entered settings mode, press * and then 2.
DISABLE: press 0 and then 1; ENABLE: press 0 and then 2
NOTE. When enabled, press * to ring bell from standby mode.
Add a Group of Cards
(Zone 1 only)
Having entered settings mode, press * and then 9.
Press 0 and then 1.
Input 3-digit starting user code, e.g. 005.
Input size of block as 3-digit number, e.g. 010 for 10 numbers/cards.
Swipe first card in block or enter card’s 8-digit number.
Repeat for additional cards.
Restore Factory Defaults
Having entered settings mode, press * and then 8.
Press 9 twice.
