F1

CAR SEAT

ECE R44/04

GROUP I, II

(9-25 kgs)

MANUAL INSTRUCTION

EN

IMPORTANT! KEEP FOR FURTHER REFERENCES.

READ CAREFULLY!

Only suitable if the approved vehicles are fitted with

3-points static or 3-point retractor safety-belts.

Approved to UN/ECER Regulation No. 16 or other equivalent standarts.

EXTREME HAZARD

Do not use in passenger seats equipped with Airbags

(SRS)

MAINTENANCE AND CLEANING

1. The car seat can be cleaned using lukewarm water and soap. Do not use aggressive cleaners like abrasives or thinner.

dryer.

Step 1. Take the car seat out of your car.

step 2. Clean food particles and dirt with a vacuum. If possible, use a vacuum cleaner’s furniture attachment to clean the small, hard-to reach areas of the car seat.

Step 3. Clean off the plastic portions of the seat with gentle soap and water.

Step 4. Remove the entire car seat cover, if possible, and run it through your washing machine gentle cycle.

Step 5. Spot clean the stained spots on the car seat if you cannot remove the cover, make certain you can use the soap on the car seat’s material by checking the package’s guidelines.

Step 6. Re-install the clean car seat in your car, and take special care that all parts of the car seat are present and installed safely and correctly.

REMOVING AND REPLACING THE COVER AND BELT PADS

1. Loosen the belts pads. (See “Adjusting the height of the shoulder belts”)

2. Loosen the cover all around. (Fig.20)

3. Pull the belts, buckle tongues and buckle through the cover.

4. Remove the cover.

5. After washing, attach the belt pads and place the cover on the shell.

6. Thread the buckle, tongues and belts through the cover and fasten the cover at the release button/positioning handle.

7. Secure the cover on the pins.

8. Close the buckle and thread the belts through the belt pads, cover and shell.

9. Connect the shoulder belts to the belt yoke.

10. Fasten the cover all around, behind the pins.

FEATURES

1. Fabric Cover

2. Hook

3. Shell

4. Shaft and Lock

5. Lock-off Device

6. Instruction Manual Storage

7. Lap Belt Indicator

8. Installation Sticker

9. Belt Yoke

10. Belt Guider

11. Base

12. Backrest

13. Head Pillow

14. Belt Slots

15. Belt Pads

16. Shoulder Belt

17. Buckle

18. Crotch Strap

19. Cushion

20. Center Adjuster

21. Adjuster Cover

22. Positioning Handle

23. Adjuster Belt

INSTALLATION

The car seat “F1” can only be used with an automatic 3-point safety belt. (Fig.1) The car seat “F1” can be used in five position (Fig.2): Pull the positioning handle under the front of the seat forwards or backwards (feel the spring underneath), release the handle on your required position while hearing a distinct click.

Fig.1

Fig.2

INSTALLING THE CAR SEAT group I /9-18 kg/

1. Place the car seat in the sleeping position 3 or 4. (Fig. 3)

2. Remove the installation shaft by pulling the moveable part of the lock from the car seat. (Fig.4-А)

3. Pull and hold the shell forward, then thread the seat belt between the shell and the base, fasten the seat belt with the seat buckle, and ensure the belt is not twisted. (Fig.5)

*Make sure the shoulder belt go from top of the seat and through the lock-off device (Fig.5-А) and the lap belt go horizontally under the lap belt indicator (Fig.5-В) and joint with the shoulder belt and buckle up the seat. (Fig.5-С)

4. Return the shell to its original position, and thread the installation shaft into the hole and lock the device by pushing the moveable part on the other side until hear a distinct click. (Fig.4-В)

5. Adjust the shell to your child’s most comfortable position.

Fig.3

pull

Fig.4-A

Fig.4-B push

Fig.5-A

Fig.5-B pull

Fig.4

Fig.5-C

Fig.5

INSTALLING THE CAR SEAT group II /15-25 kg/

This installation method is for child within Group ІI (15 – 25 kg).

1. Remove the harness system first, including thee belt pads, buckle and crotch strap..

2. Install the shoulder and lap belt by threading the vehicle’s lap and shoulder belt through the hook

(Fig.6-А) on the top of shell and over the belt guider. (Fig.6-7)

Fig.6-A

Fig.6

Fig.7

PLACING YOUR CHILD

IN THE CAR SEAT

1. Loosen the shoulder belts by pressing the push button and pull the shoulder belts towards you.

Important: Do not pull on the belt pads when doing so. (Fig.8-9)

2. Press the red button to open the buckle. (Fig.10)

3. Part the belts over the sides of the shell. (Fig.11)

4. Position your child into the shell and make sure that there are no toys or other hard objects in the shell. (Fig.12)

5. Match buckle tongue sections together and insert them into the buckle. (Fig.13)

6. Make sure the shoulder belts fit your child snugly by pulling the adjuster belt. (Fig.14) pull

Press open

Fig.8

Fig.9

Fig.10

Fig.11

Fig.12

Fig.13

pull

Fig.14

ADJUSTING THE HEIGHT

OF THE SHOULDER BELTS

1. The correct belt height of the shoulder belts is attained when the belt disappears into the shell slightly above the shoulder of the child. Ensure that the shoulder belts fit comfortably over the child’s shoulder. (Fig.15)

2. Loosen the shoulder belts by pressing the push button of the adjuster and pulling the shoulder belts towards you as far as possible.

Important: Do not pull the belt pads when doing so. (Fig.9)

3. Place the shell of the seat in the sleeping position.

4. Remove the shoulder belts from the yoke. (Fig.16-А).

5. Pull the shoulder belts through the shell and cover out of the belt pads, ensuring that the buckle remains fixed to prevent the belts from twisting. (Fig.17)

6. If you wish to alter the belts from or to the lowest positions, place the car seat in the sleeping position.

7. If you wish to alter the belts from or to higher positions, place the car seat in the sitting position.

8. Place the shoulder pads at the desired height and thread the shoulder straps back through the shoulder pads, cover and shell. (Fig.18)

9. Connect the shoulder belts to the belt yoke. (Fig.19-А)

Fig.16-A

Fig.16

Fig.15

pull

Fig.17

Fig.18

Fig.19-A

Fig.19

Fig.20

Дидис ООД - България

Шумен 9700, “Правда” 1

Тел.: 054/850 830

Факс: 054/850 839 e-mail: [email protected]

www.bertoni-eu.com

Didis Ltd. - Bulgaria

Shumen 9700, “Pravda” 1 Str.

Tel.: +359 54 850 830

Fax: +359 54 850 839 e-mail: [email protected]