INSTRUCTION MANUAL For the T-Safe General - promet

INSTRUCTION MANUAL For the T-Safe General - promet
INSTRUCTION MANUAL
For the T-Safe
General Information:
Factory Master-Code is 1-2-3-4-5-6. User code is not activated.
For power supply use batteries of 9V type «ALKALINE»
Don’t forget to change Factory Master-Code to your Personal Master-Code.
1. How can I open the safe?
1.1 Press the button «*». You will hear a single signal and the green light is on.
1.2 Enter master- or user- code, from 4 to 6 digits (Factory master-code is 1-2-3-4-5-6)
1.3 Press «ENTER».
If you entered the correct code, you will hear a signal two times and the green light will be on during
the next 5 seconds.
1.4. While the green light is on, turn the handle of the lock clockwise and open the door.
1.5. Lockout Mode. If you entered incorrect code, you will hear a signal three times and the red light
is on. After three wrong entries, the lock keypad is blocked for five minutes. During all the time while
the keypad is blocked the red light is lit with the interval of five seconds (during this time one can’t
open the lock even when printing-in the correct code).
Note:
Each click to the keypad key (except «ENTER» button after entering the correct code) is confirmed by a single short sound
signal and the green light. If the button is not pressed during ten seconds, the lock is switched off, that is confirmed by a
single sound signal and the green light is on.
2. How can I close the safe?
Close the door of the safe and turn the lock handle counterlockwise to stop. The lock is now closed.
ATTENTION:
• The Change of the old code combination to the new one should be done
while the Door of the safe is Open.
• After changing the code combination please Check the new code two or three
times while the Door is Open.
3.How can I change the code?
3.1 Changing of the master-code
-Press button «*»;
-Press button«ENTER»;
-Press button «1»;
-Press button «ENTER»;
-Enter the present master-code and press «ENTER»;
-Enter the new master-code (minimum 4, maximum 6 digits) and press «ENTER»;
-Repeat the new master-code and press «ENTER».
Note:
If the new master-code is entered correct, you will hear signal two times and the green light will be lit twice. If the new master-code is
entered incorrect, you will hear signal three times and the red light will l be it twice. The old master-code remains.
If you made a mistake, please start from the beginning by pressing button «ENTER».
3.2 Changing the User code (using the «master-code»)
-Press button «*»;
-Press button «ENTER»;
-Press button «2»;
-Press button «ENTER»;
-Enter the present master-code and press «ENTER»;
-Enter the user code (minimum 4, maximum 6 digits) and press «ENTER»;
-Repeat the new user code and press «ENTER».
Sound and light signals are the same as for programming
the
master-code.
3.3 Changing the User-code (without entering master-code)
Note:
It is possible to change the user code without the entering of the master-code only after the user-code
was set with the help of the master-code.
-Press button «*»;
-Press button «ENTER»;
-Press button «3»;
-Press button «ENTER»;
-Enter the present user code and press «ENTER»;
-Enter the new user code (minimum 4, maximum 6 digits) and press «ENTER»
-Repeat the new user-code” and press «ENTER».
Sound and light signals are the same as for programming the “master-code”.
3.4 Deleting the user-code (only after entering the master-code).
-Press button «*»;
-Press button«ENTER»;
-Press button «0»;
-Press button «ENTER»;
-Enter the present master-code and press «ENTER»;
The user-code is deleted, only the master-code is active.
Sound and light signals are the same as in programming the user code.
4. Changing the batteries
For the power supply to the lock 9V type «ALKALINE» battery is used. It is set in the lower part
of the keypad body under the removable cover. Replace the old battery with the new one. The code is
in the memory even if the battery is switched off.
It is recommended to change the batteries at least once a year.
5. Service
If the Lock is damaged, a signal will sound three times and both lights are on. In this case
please contact the service person.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement