QUENTIN 7440.152 | American Standard QUENTIN 7440.151, 7440.152 Vessel Lavatory Fitting Installation Instructions

QUENTIN

™

VESSEL LAVATORY FITTING

Installation

Instructions

7440.151

7440.152

Thank you for selecting American-Standard...the benchmark of fine quality for over 100 years.

To ensure that your installation proceeds smoothly--please read these instructions carefully before you begin.

Recommended Tools

Regular Screwdriver

Phillips Screwdriver Adjustable Wrench Plumbers' Putty or Caulking

1 INSTALL LAVATORY FAUCET

CAUTION

Turn off hot and cold water supplies before beginning.

Slide EXTENSION (8) over FAUCET SUPPLIES (3). Thread

EXTENSION (8) onto FAUCET BODY (9) and fully tighten.

CAUTION: Do not damage finish on faucet EXTENSION (8) when tightening.

Seat SEAL (1) into groove in under side of ESCUTCHEON BASE (2).

Feed FAUCET SUPPLIES (3) and MOUNTING SHANK (4) through hole in mounting surface.

From below, install SUPPORT PLATE (7) GASKET (5) and MOUNTING

NUT (6) onto SHANK (4). Secure Faucet with MOUNTING NUT (6).

Before final tightening, adjust Faucet so that it is centered. Tighten

MOUNTING NUT (7) to complete mounting.

NOTE: For thick deck installations, the SUPPORT PLATE (7) can be omitted.

Certified to comply with ANSI A112.18.1M

M 9 6 5 2 2 8 R E V. 1 . 1

Channel Locks

9

8

GROOVE

(FAUCET BASE)

MOUNTING SURFACE

2

1

4

7

5

6

3

2

MAKE WATER SUPPLY CONNECTIONS

Turn off hot and cold water supplies before beginning.

Connect FLEXIBLE SUPPLIES (1, 2) directly to wall supplies. Connection on fitting supplies are 3/8" compression. Connect left supply to Hot and right supply to the Cold wall supply. Use adjustable wrench to tighten connections. Do not over tighten.

Faucet supplies are 28" long from faucet base.

Note: If additional supply length is required, installer must purchase additional parts separately.

Important: If SUPPLY HOSES (1, 2) are too long, loop as illustrated to avoid kinking.

Figure A.

HOT

Figure A.

COLD

3

DRAIN INSTALLATION

Apply a bead of PUTTY to underside of

DRAIN BODY FLANGE (1).

Feed DRAIN BODY (1) down through lavatory.

Assembly GASKET (2) WASHER (3) and LOCKNUT (4) onto DRAIN BODY (1). Tighten LOCKNUT (4) firmly.

Assembly TAILPIECE (5) to DRAIN BODY (1).

28"

HOT

2

LOOP SUPPLIES

IF REQUIRED

COLD

1

PUTTY

1

2

3

4

5

M 9 6 5 2 2 8 R E V. 1 . 1

4

TEST INSTALLED FAUCET

AND CHECK FOR LEAKS

With HANDLE (1) in OFF position, turn on WATER

SUPPLIES (2) and check all connections for leaks.

Remove AERATOR (3).

Operate HANDLE (1) to flush water lines thoroughly.

Replace AERATOR (3).

3 HOT

OFF

ON

COLD

1

HOT

2

COLD

5

SERVICE CAUTION

Turn off hot and cold water supplies before beginning.

To remove or replace cartidge: Fig. A.

Turn valve to OFF position.

Remove HANDLE SCREW (2).

Pull off HANDLE (3) and CAP (4).

Unthread CARTRIDGE NUT (5) and remove.

Pull out CARTEIDGE (6).

Inspect CARTRIDGE (6) and O-RING (7) for debris and clean if necessary.

Clean MANIFOLD (1) and rinse clean.

Reinstall CARTRIDGE (6) and O-RING (7) onto

MANIFLOD (1).

Reinstall CARTRIDGE NUT (5), CAP (4) and

HANDLE ASSEMBLY (3).

If spout drips, operate handle several times from

OFF to ON and HOT to COLD position. Do not force - handles turn only 90˚.

7

6

5

4

3

1

2

2.5mm HEX KEY

6

CARE INSTRUCTIONS:

DO: SIMPLY RINSE THE PRODUCT CLEAN WITH CLEAR WATER. DRY WITH A SOFT COTTON FLANNEL CLOTH.

DO NOT: DO NOT CLEAN THE PRODUCT WITH SOAPS, ACID, POLISH, ABRASIVES, HARSH CLEANERS, OR A

CLOTH WITH A COARSE SURFACE.

M 9 6 5 2 2 8 R E V. 1 . 1

M922894 -YYY0A

AERATOR

M919343-YYY0A

EXTENSION KIT

M962682-0070A

CARTRIDGE

QUENTIN

™

VESSEL LAVATORY FITTING

MODEL NUMBER

7440.151

7440.152

M904524 -0070A

CARTRIDGE NUT

M907059-YYY0A

CARTRIDGE COVER

M964143-YYY0A

HANDLE KIT

M918004-0070A

SET SCREW

Replace the "YYY" with appropriate finish code

CHROME

OIL RUBBED BRONZE

SATIN NICKEL

002

224

295

A911903-0070A

SEAL

A923480-0070A

SUPPORT PLATE

M961634-0070A

MOUNTING KIT

070532-0040A

TAILPIECE

015025-YYY0A

DRAIN COMPLETE

HOT LINE FOR HELP

For toll-free information and answers to your questions, call:

1 (800) 442-1902

Weekdays 8:00 a.m. to 6:00 p.m. EST

IN MEXICO 01-800-839-1200

IN CANADA 1-800-387-0369 (TORONTO 1-905-306-1093)

Weekdays 8:00 a.m. to 7:00 p.m. EST

Product names listed herein are trademarks of American Standard Inc.

© AS America,Inc. 2011 M 9 6 5 2 2 8 R E V. 1 . 1