ksa1004 installation instructions

Add to my manuals
6 Pages

advertisement

ksa1004 installation instructions | Manualzz

I N S T A L L A T I O N I N S T R U C T I O N S

Small Flat Panel Lift Arm

FSA-1004 and KSA-1004

The Lift Arm FSA/KSA-1004 is an accessory that can be used with a broad range of Small Flat Panel Displays.

The FSA/KSA-1004 allows the user to move a display vertically up or down in a 13 inch radius. The lift arm can be moved vertically 6-1/2” up from center and 6-1/2” down from center.

The FSA/KSA-1004 is designed to safely hold a display weighing up to 25 lbs. (11.3kg). The display can be up to

30 inches wide.

The FSA/KSA-1004 accommodates all VESA®

75mm/100mm compliant displays.

BEFORE YOU BEGIN

Lift Arm

CAUTION: To prevent damage to the mount, which could affect or void the Factory warranty, thoroughly study all instructions and illustrations before you begin to install the mount brackets. Pay particular attention to the “Important Precautions” on Page 2.

• If you have any questions about this installation, contact Chief Manufacturing at 1-800-582-6480 or 952-582-6480.

CHIEF MANUFACTURING INC.

1-800-582-6480 952-894-6280 FAX 952-894-6918

8401 EAGLE CREEK PARKWAY, STE. 700

SAVAGE, MINNESOTA 55378 USA

8832-000041 Rev. E

2004 Chief Manufacturing www.chiefmfg.com

04/05

Installation Instructions

IMPORTANT WARNINGS and CAUTIONS!

WARNING A WARNING alerts you to the possibility of serious injury or death if you do not follow

the instructions.

FSA/KSA-1004

CAUTION A CAUTION alerts you to the possibility of damage or destruction of equipment if you do not follow the corresponding instructions.

WARNING Improper installation can result in serious personal injury! Make sure that the mounting surface can support a redundant weight factor five times the total weight of the equipment: if not, reinforce the mounting surface structural members before

installing the FSA/KSA-1004.

WARNING Be aware of the potential for personal injury or damage to the unit if it is not

adequately mounted.

WARNING

The installer is responsible for verifying that the mounting surface to which the

FSA/KSA-1004 is anchored will safely support the combined load of all attached

components or other equipment.

WARNING The combined weight of the display placed on the FSA/KSA-1004 must not exceed 25

lbs. (11.3kg), the maximum load capacity of the mount.

WARNING Watch for pinch points. Do not put your fingers between movable parts.

WARNING Make sure the mount is correctly oriented.

WARNING When using an OFB and adding an additional arm to an existing mount, the total number of arms on the mount cannot exceed two arms.

CAUTION

CAUTION

Check the unit for shipping damage before you begin the installation.

Over-tightening mounting screws may damage your display.

TOOLS REQUIRED FOR

INSTALLATION

CONTENTS

PARTS .........................................................................3

PARTS LIST.................................................................3

INSTALLATION............................................................4

Removing the Display from the Mount .....................4

Installing the Lift Arm ................................................5

Installing base end of lift arm ................................5

Installing display end of lift arm.............................5

Adjusting Lateral Movement .....................................6

Adjusting Lift Arm Tension........................................6

Cable Management ..................................................6

• 5/32” Hex key wrench (provided)

• 3/16” Hex Key wrench (provided)

NOTE: Other tools may be required depending on the method of installation.

2

Installation Instructions

PARTS

30

50

70

70

Tension adjustment bolt

10

50

30

70

70

20

FSA/KSA-1004

40

20

60

PARTS LIST

Figure 1. Lift Arm Installation Drawing

80

Table 1. Lift Arm Parts

PART DESCRIPTION QTY

10

LIFT ARM

1

20 WASHER , UHMW , .640

ID X .845

OD 2

30 WASHER , UHMWPE , .318

ID X .031

OD 2

40 PIVOT PIN , SPF 1

50 CAPSCREW , BUTTON HEAD 2

60 LOCK NUT , NYLOCK 1

70 SPACER , STAINLESS STEEL , .320

X .018 4

80 LARGE LOCK NUT , NYLOCK 1

3

Installation Instructions

INSTALLATION

Adding a lift arm modifies your mount configuration. This procedure applies to most small flat panel displays, particularly those with a pivot or swing arm, whether wall mount or desk mount.

Removing the Display from the Mount

To remove the display from its mount, perform the following steps:

NOTE: Do not remove the four screws (not shown) that attach the display to the interface bracket.

1. Disconnect the power/audio/video cables from the display (not shown).

2. Remove the cap screw, washers, pivot pin, and retaining nut from the display end of the mount.

Refer to Figure 2. Separate the display from the mount.

FSA/KSA-1004

3. To remove the pivot pin (see Figure 2) from the other end, do the following: a. If the mount is a pivot/pitch wall mount, remove the attaching hardware from the display. b. If the mount is wall mounted, desk mounted, or has more than one swing arm, remove the attaching hardware from the arm closest to the display.

NOTE: The two button head cap screws removed from the mount will be replaced with longer screws when the lift arm is installed.

NOTE: Keep the pivot pin removed in step 2. This part will be used again when the lift arm is installed.

Cap screw

Small

Washer

Pivot Pin

Large

Washer

Flat Washers

Display Mount Parts — Typical

PART NAME QTY

SCREW , CAP 2

WASHER , FLAT 4

SMALL WASHER , NYLON 2

LARGE WASHER , NYLON 2

NUT , NYLOCK 2

Nut

Figure 2. Single Swing Arm (FWS-110) — Example

4

Installation Instructions

Installing the Lift Arm

To install the lift arm, perform the following procedures:

Installing base end of lift arm

1. Locate the tension adjustment bolt on the lift arm

(see Figure 3). Install the pivot pin (40) and a washer

(20) onto the base of the mount.

2. Assemble a button head cap screw (50), one stainless steel washer (70), washer (30), and a second stainless steel washer (70) onto button head cap screw (50) as shown in Figure 3.

3. Insert the screw assembly (step 2) into the pivot hole on the lift arm (10) and the base end of the mount.

4. Thread the lock nut (60) to the screw assembly (step

2) at the bottom of the mount.

CAUTION: Over-tightening a tension screw (50) will cause excessive wear and may distort adjustment components.

5. Using the 3/16” hex key (provided), tighten the button head cap screw (50) into the nut (60) several turns, leaving flexibility in the hinged joint. Do not over-tighten the cap screw (50).

FSA/KSA-1004

Installing display end of lift arm

1. Install the original pivot pin (see Figure 3) that was retained when the display was removed and a washer (20) onto the base of the mount.

2. Assemble a button head cap screw (50), one stainless steel washer (70), washer (30), and a second stainless steel washer (70) onto button head cap screw (50) as shown in Figure 3.

3. Insert the screw assembly (step 2) into the pivot hole on the lift arm (10) and the display end of the mount.

4. Thread the lock nut (80) to the screw assembly (step

2) at the bottom of the mount.

CAUTION: Over-tightening a tension screw (50) will cause excessive wear and may distort adjustment components.

5. Using the 3/16” hex key (provided), tighten the button head cap screw (50) into the nut (80) several turns, leaving flexibility in the hinged joint. Do not over-tighten the cap screw (50).

20

50

30

Original

Pivot

Pin

50

70

Lift Arm Parts

ITEM PART NAME QTY

10 LIFT ARM 1

20 LARGE WASHER , NYLON 2

30 SMALL WASHER , NYLON 2

40 PIVOT PIN , SPF 1

50 CAP SCREW , BUTTON HEAD 2

60 LOCK NUT , NYLOCK 1

70 SPACER , STAINLESS STEEL 4

80 LARGE LOCK NUT , NYLOCK 1

80

40

10

20

60

Figure 3. Installing Lift Arm

5

Installation Instructions

Adjusting Lateral Movement

CAUTION: Over-tightening tension bolt will cause excessive wear and may distort adjustment components.

To adjust the lateral movement tension, perform the following procedures:

1. Slightly tighten or loosen the tension adjustment bolt.

2. Check for desired tension. Repeat as necessary.

Adjusting Lift Arm Tension

CAUTION: Over-tightening tension bolt will cause excessive wear and may distort adjustment components.

To adjust the tension of the lift arm:

1. Raise or lower the lift arm until tension adjustment bolt appears in the opening.

2. Using the 5/32” hex key (provided), adjust the tension adjustment bolt, as follows:

NOTE: There is no fixed number of revolutions to turn the tension adjustment bolt. Tighten or loosen the bolt, as needed. When the bolt is adjusted correctly, the display can be easily raised or lowered at any time, and stay in place without sagging. a. To increase lift arm tension, turn the tension adjustment bolt counterclockwise. b. To decrease lift arm tension, turn the tension adjustment bolt clockwise.

3. Raise or lower the lift arm to check for desired tension. Repeat step 2 as needed.

Cable Management

CAUTION: Make sure your cables do not run through a pinch point.

Connect and secure power/audio/video cables, making sure to leave sufficient slack to allow for movement of the display.

Cable

Management

Slot

Adjusting Lateral Movement

Lift Arm Tension

Adjustment Bolt

FSA/KSA-1004

Lateral

Tension

Adjustment

Bolts

(Typical)

Adjusting Lift Arm Tension

6

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals